The merge areas of freeway work zones include relatively significant safety hazards that have continuously led to urgent safety issues to be solved by the management departments. In order to make up for the cumbersome process of independent identification of rear-end collision and lane change collision on complex road sections, an appropriate identification method of traffic conflicts in the merge area of freeway work zone was explored, this study collected vehicle running tracking data from the merge areas of multiple work zones, using an unmanned aerial vehicle video technique. Based on an inter-frame difference method and the principle of a spatio-temporal context visual tracking algorithm, the vehicles were detected and tracked, and the coordinate data of the vehicles in continuous motion were parsed using MATLAB extension tools. Based on the behavior characteristics of vehicle conflict avoidance, a new identification method for evading severe traffic conflicts is proposed according to the initial velocity, acceleration and accident rate of section traffic. Then, a statistical analysis was performed on the spatial distribution characteristics of the traffic conflicts in typical merge areas. The impacts of the road conditions in work zones, vehicle factors, and traffic flow factors on the traffic conflicts were analyzed. A binomial logistic model was established to identify the main influencing factors. The results show that in the merge area of the freeway work zone, there are serious traffic conflicts between vehicles in the following two situations: (Ⅰ) v∈[7,13.5] m/s and a∈[-3.96,-0.65]m/s2; and (Ⅱ) v∈[13.5,24.3] m/s, and a∈[-3.96,-1.57] m/s2. The probabilities of serious traffic conflicts in the first and last 25 m of the merge area are greater than those in the other sections. The smaller the space between the upstream work zone and the merge area, the greater the probability of serious traffic conflicts between vehicles. When the average vehicle speed is relatively high, the probability of serious conflicts is the highest, i.e., by a multiple of 5.95 from the baseline. Moreover, the probability of serious conflicts between vehicles is higher for larger vehicles, i.e., 4.765 times that for small vehicles. The research results can serve as a reference for freeway management departments to improve the safety levels of merge areas during road work. For example, the probability of serious conflicts can be effectively reduced by setting up reasonable speed limit signs in the work zone, increasing the spacing between work zone and merge area, and appropriately diverting large vehicles.

Plastic flow in body-centered cubic (bcc) alloys is governed by the thermally-activated screw dislocation motion. In bcc interstitial solid solutions, solute diffusion can occur at very fast rates owing to low migration energies and solute concentrations. Under mechanical loading, solutes may move on the same or similar time scale as dislocations glide, even at low temperatures, potentially resulting in very rich co-evolution processes that may have important effects in the overall material response. It is therefore important to accurately quantify the coupling between interstitial impurities and dislocations, so that larger-scale models can correctly account for their (co)evolution. In this paper, we use electronic structure calculations to obtain the energetics of oxygen diffusion under stress and its interaction energy with screw dislocation cores in bcc tungsten. We find that oxygen atoms preferentially migrate from tetrahedral to tetrahedral sites with an energy of 0.2 eV. This energy couples only weakly to hydrostatic and deviatoric deformations, with activation volumes of less than $0.02$ and $0.2b^3$, respectively. The strongest effect is found for the inelastic interaction between O atoms and screw dislocation cores, which leads to attractive energies on the order of 1.5 eV and a structural transformation of the screw dislocation core from an `easy' to a `hard' core configuration

Aborycin is a type I lasso peptide with a stable interlocked structure, offering a favorable framework for drug development. The aborycin biosynthetic gene cluster gul from marine sponge-associated Streptomyces sp. HNS054 was cloned and integrated into the chromosome of S. coelicolor hosts with different copies. The 3-copy gul-integration strains S. coelicolor M1346::3gul showed better production than one-copy or 2-copy gul-integration strains, and the total titer reached approximately 10.4 mg/L, i.e., 2.1 times that of the native strain. Then, five regulatory genes, phoU (SCO4228), wblA (SCO3579), SCO1712, orrA (SCO3008) and gntR (SCO1678), which were reported to have negative effects on secondary metabolism, were further knocked out from the M1346::3gul genome by CRISPR/Cas9 technology. While the ΔSCO1712 mutant showed a significant decrease (4.6 mg/L) and the ΔphoU mutant showed no significant improvement (12.1 mg/L) in aborycin production, the ΔwblA, ΔorrA and ΔgntR mutations significantly improved the aborycin titers to approximately 23.6 mg/L, 56.3 mg/L and 48.2 mg/L, respectively, which were among the highest heterologous yields for lasso peptides in both Escherichia coli systems and Streptomyces systems. Thus, this study provided important clues for future studies on enhancing antibiotic production in Streptomyces systems.

Aromatic azo compounds have -N=N- double bonds as well as larger π electron conjugation system, which endows aromatic azo compounds with wide applications in the fields of functional materials. The properties of aromatic azo compounds are closely related to the substituents on their aromatic rings. However, traditional synthesis methods, such as the coupling of diazo salts, have a great limitation on the structural design of aromatic azo compounds. Therefore, many scientists have devoted their efforts to developing new synthetic methods. Moreover, recent advances in the synthesis of aromatic azo compounds led to the improvement of design and preparation of light-response materials at molecular level. This review summarizes the important synthetic progress of aromatic azo compounds in recent years, with an emphasis on the pioneering contribution of functional nanomaterials in the field.

The Danxia landform area of Jingbian Wave Valley is located in the central part of Ordos Basin. The near-red Danxia landform consisting of sandstone in this area is a new discovery in geological circles at home and abroad, and its depositional age and genesis remain a hot topic of discussion at present. As the material basis for its development, red sandstone is of great importance to the in-depth study on its formation date and origin. The paper explores the origin, tectonic significance and paleogeographic pattern of the red sandstone through field geological investigation and zircon U-Pb dating analysis of the red sandstone of the Luohe Formation. The results show that the original materials of the red sandstone was formed in three main age intervals, 252~456 Ma, 1657~2084 Ma, and 2129~2538 Ma, and regional tectonothermal events in the origin area during the three periods were recorded, among which the events in Mesoproterozoic and Paleoproterozoic periods were the most active. The comparative analysis of zircon U-Pb age spectra shows that for the sediment of red sandstone, the early origin is near-origin and late origin is distant-origin. The main origin areas in the study area are the Xingmeng orogenic belt, the North China massif and the Alashan massif; the vertical section reflects that the origin area has the strongest erosion and transport in the upper deposition period, the smallest erosion and transport in the middle deposition period, and the moderate erosion and transport in the lower deposition period. With origins system dominated by the northern origins and the paleogeographic pattern of multi-period and cyclonic, the area mainly experienced four tectonic movement cycles, such as Wutai, Lvliang, Caledon and Haixi.

Based on acoustic fluid elements, dynamic analysis was performed on liquid sloshing modes and liquid-filled containers considering the fluid-structure interaction (FSI) effect. The liquid sloshing modes in two-dimensional (2D) and three-dimensional (3D) containers were analyzed, and the results were compared with liquid sloshing modes measured in tests and theoretically calculated modes. This thus verifies correctness of the simulation method based on acoustic fluid elements. Cylindrical liquid-filled containers with different water levels were subjected to modal analysis and dynamic and time-historical analysis. Results show that the finite element analysis (FEA) based on acoustic fluid elements can accurately simulate liquid sloshing modes in liquid-filled containers and vibration characteristics of these containers with different liquid levels. The vibration frequency of liquid-filled containers declines obviously with rising liquid level. The liquid level significantly affects distributions of the maximum displacement, maximum acceleration, and maximum von Mises stress on the sidewall of liquid-filled containers. Numerical simulations based on acoustic fluid elements provides an effective and reliable method for dynamic analysis of liquid-filled containers considering the FSI effect.

Consumer preference for products made from transgenic technology has been widely studied, yet few studies exist exploring the factors influencing producers’ adoption of transgenic technology. Based on field surveys in Chinese provinces of Shanxi, Henan and Shandong, we employed a gambling experiment to capture producers’ risk preferences by estimating their risk aversion coefficients. We further estimated producers’ risk amplification and risk perception of GM technology. Using ordered logit model and Poisson model we identified the major factors influencing producers’ adoption of transgenic technology. We found the factors impacted the decision of producers from different regions in different ways. The results showed that over 60% of participants amplified the risk of transgenic crops. When there was potential risk, producers might not be rational even if they had high level of knowledge and cognition about the technology. Our results shed light on government policies aiming to increase the adoption of new technologies by producers.

This experiment aimed to investigate the impact of malic acid (MA) and citric acid (CA) on the nutritional composition, fermentation quality, rumen degradation rate, and microbial diversity of a mixture of apple pomace and corn protein powder during ensiling. The experiment used apple pomace and corn protein powder as raw materials, with four groups: control group (CON), malic acid treatment group (MA, 10g/kg), citric acid treatment group (CA, 10g/kg), and citric acid + malic acid treatment group (MA, 10g/kg + CA, 10g/kg), subjected to mixed ensiling for 60 days. The results indicated: (1) Compared to the CON group, the crude protein content significantly increased in the MA, CA, and MA+CA groups (p < 0.05), with the highest content observed in the MA+CA group. The addition of MA and CA effectively reduced the water-soluble carbohydrate (WSC) content (p < 0.05). Simultaneously, the CA group showed a decreasing trend in NDFom and hemicellulose content (p = 0.08; p = 0.09). (2) Compared to the CON group, the pH significantly decreased in the MA, CA, and MA+CA groups (p < 0.01), and the three treatment groups exhibited a significant increase in lactic acid and acetic acid content (p < 0.01). The quantity of lactic acid bacteria increased significantly (p < 0.01), with the MA+CA group showing a more significant increase than the MA and CA groups (p < 0.05). (3) Compared to the CON group, the in situ dry matter disappearance (ISDMD) significantly increased in the MA, CA, and MA+CA groups (p < 0.05). All three treatment groups showed highly significant differences in in situ crude protein disappearance (ISCPD) compared to the CON group (p < 0.01). (4) Good's Coverage for all experimental groups was greater than 0.99, meeting the conditions for subsequent sequencing. Compared to the CON group, the Shannon index significantly increased in the CA group (P < 0.01), and the Simpson index increased significantly in the MA group (p < 0.05). However, there was no significant difference in the Chao index among the three treatment groups and the CON group (p > 0.05). At the genus level, the abundance of Lentilactobacillus in the MA, CA, and MA+CA groups was significantly higher than in the control group (p < 0.05). PICRUSt prediction results indicated that the metabolic functional microbial groups in the CA and MA treatment groups were significantly higher than in the CON group (p < 0.05), suggesting that the addition of MA or CA could reduce the loss of nutritional components such as protein and carbohydrates in mixed ensilage. In conclusion, the addition of malic acid and citric acid to a mixture of apple pomace and corn protein powder during ensiling reduces nutritional losses, improves fermentation quality and rumen degradation rate, enhances the diversity of the microbial community in ensiled feed, and improves microbial structure. The combined addition of malic acid and citric acid demonstrates a superior effect.

Prunus tenella is a rare and precious relict plant in China. It is an important genetic resource for almond improvement and an indispensable material in ecological protection and landscaping. However, the research of molecular breeding and genetic evolution has been severely restricted, due to the lack of genome information. In this investigation, we created a chromosome-level genomic pattern of P. tenella, 231Mb in length with a contig N50 of 18.1 Mb by Hi-C techniques and high-accuracy PacBio HiFi sequencing. The present assembly predicted 32088 protein-coding genes, and an examination of the genome assembly indicated that 94.7% among all assembled transcripts were alignable to the genome assembly; most (97.24%) were functionally annotated. By phylogenomic genome comparison, we found that P. tenella is an ancient group that diverged approximately 13.4 million years ago (Mya) from 13 additional closely related species and about 6.5 Mya from the cultivated almond. Collinearity analysis revealed that P. tenella is highly syntenic and has high sequence conservation with almond and peach. However, this species also exhibit many presence/absence variants. Moreover, a large inversion at the 7,588 kb position of chromosome 5 was observed, which may have a significant association with phenotypic traits. Lastly, population genetic structure analysis in eight different populations indicated a high genetic differentiation among the natural distribution of P. tenella. This high-quality genome assembly provides critical clues and comprehensive information for the systematic evolution, genetic characteristics, and functional gene research of P. tenella. Moreover, it provides a valuable genomic resource for in-depth study in protecting, developing, and utilizing P. tenella germplasm resources.

Reducing the hardness of hard water is of great concern nowadays due to some adverse effects on water pipes, boilers and soap consumption. Using the method of biomineralization to precipitate calcium and magnesium ions to become carbonate minerals was one of the most important innovations for reducing the hardness of hard water. The present study sought to explore the physical and chemical conditions of carbonates bio-precipitation and the potential use of Bacillus licheniformis SRB2 strain (GenBank: KM884945.1) isolated from sludge sample of Moshui River (Shandong University of Science and Technology, Qingdao, China) in reducing the hardness of hard waters by the induction of carbonate minerals. In this study, B. licheniformis SRB2 strain was identified based on the morphological, biochemical and 16S rDNA gene sequence homology analysis. The carbonate minerals induced by B. licheniformis bacteria in the liquid culture medium with 3% NaCl and Mg/Ca molar ratio of 0, 6, 8, 10 and 12 were investigated. The culture medium was inoculated with the bacterial liquid seed was set as the experimental group and the other culture medium was inoculated with the same volume of distilled water was set as the control group. The mineral phases, micromorphologies, and crystal structures were analyzed using X-ray powder diffraction, scanning electron microscope, energy dispersive X-ray detector, high resolution transmission electron microscopy and selected area electron diffraction. The bacterial concentrations and pH values of the solution were measured by a spectrophotometer and a pH meter, respectively. The urease secreted by B. licheniformis SRB2 was found to greatly increase the pH values of the liquid medium, which favored the formation of calcium carbonate.As a result, Mg²⁺ and Ca²⁺ ion concentrations decreased greatly due to the biomineralization of calcium carbonate and nesquehonite minerals in the presence of B. licheniformis SRB2 bacterium. There were only few calcium carbonates and no nesquehonite minerals in the control groups. It was also found that the minerals of nesquehonite induced by B. licheniformis SRB2 had a phenomenon of preferred orientation. What was more, even though Mg²⁺ ions inhibited the precipitation of Ca²⁺ ions, but under the action of B. licheniformis SRB2 bacteria, the inhibition effect was significantly declined. The bio-precipitation of calcium carbonate and nesquehonite minerals may represent a new method of pretreatment for the hardness reduction of hard water. The accomplished study is of certain interest for interpretation of the carbonates biomineralization in natural environment, and maybe also has a certain application value in the former processing of hard water

The fall armyworm, Spodoptera frugiperda (Lepidoptera, Noctuidae), is a notorious migratory pest. After invading China in 2019, the species has established as a year-round breeding population in most of the southern provinces. The area of winter corn in this region has been increasing due to the huge demand of fresh corn consumption which is potentially at risk from this invasive, although S. frugiperda growth and development under changing climate in this region is unclear, particularly the rising temperature during night period. Here we used highest daily temperatures of 27℃, 24℃, 20℃ and night temperatures that were 2℃, 4℃, 6℃ lower giving three daily temperature treatments reflective of winter conditions; GroupⅠ: 27-21℃, 27-23℃, 27-25℃, Group Ⅱ: 24-18℃, 24-20℃, 24-22℃, and Group Ⅲ: 20-14℃, 20-16℃, 20-18℃; to evaluate the effect of increasing night temperature on growth and development of S. frugiperda. Results show that the survival rate of larvae and pupae significantly declined with the daily temperature declining and the night temperature range increasing. Significant developmental effects were observed in all day-night temperature treatment, except for adults, with significant interaction effects for all stages except egg and generation time. Development rate accelerated along with the increasing daily temperature and night temperature, except for the intermediate treatments (Group Ⅱ). The uniformity of pupation and emergence times are higher in high daily temperatures and night temperature. Predictions of FAW development and warnings to local farmers need to be adjusted to take into account the more rapid development. These results will support decision makers to develop long-term management strategies for FAW in southern China.

With a highly efficient optical absorption capability, bismuth selenide (Bi2Se3) nanomaterial can be used as an outstanding photothermal agent for anti-tumor treatment and shows promise in the field of nanotechnology-based biomedicine. However, little research has been done on the relevant mechanism underlying the photothermal killing effect of Bi2Se3 nanomaterial. Herein, the photothermal effects of Bi2Se3 nanoparticles on A549 cells were explored with emphasis put on autophagy. Firstly, we characterized the structure and physicochemical property of the synthesized Bi2Se3 and confirmed their excellent photothermal conversion efficiency (35.72%), photostability, biocompatibility and ability of photothermal killing on A549 cells. Enhanced autophagy was detected in Bi2Se3-exposed cells under an 808 nm laser. Consistently, an elevated expression ratio of LC3-II to LC3-I, a marker of autophagy occurrence, was induced in Bi2Se3-exposed cells upon NIR irradiation. Meanwhile, the expression of cleaved-PARP was increased in the irradiated cells dependently on the exposure concentrations of Bi2Se3 nanoparticles. Pharmacological inhibition of autophagy by 3-methyladenine (3-MA) further strengthened the photothermal killing effect of Bi2Se3. Meanwhile, stress-related signaling pathways including p38 and SAPK/JNK were activated coupled with the attenuated PI3K/Akt signaling. Our study figures out that autophagy and the activation of stress-related signaling pathways were involved in the photothermal killing of cancerous cells by Bi2Se3, which provides a more understanding of photothermal nanomaterials.

As the lifespan of porous asphalt pavement extends, it invariably experiences performance degradation and an increase in tire/pavement noise compared with the original surface when it is newly built. To understand the medium-term performance of porous asphalt pavement during service and reveal the influence of different pavement performance indicators on tire/pavement noise generation, a seven-year continuous observation and data analysis study was conducted. Porous asphalt with different designed material parameters was taken into account, including thin-layer porous asphalt overlay with a maximum nominal aggregate size of 10mm (PUC-10), porous asphalt with a maximum nominal aggregate size of 13mm (PAC-13), and a two-layer porous asphalt incorporating both PUC-10 and PAC-13 (PUC-10+PAC-13). Using automated pavement technology testing equipment, key performance indexes, including damage rate (DR), rut depth (RD), international roughness index (IRI), and sideway force coefficient (SFC), were measured and calculated. The on-board sound intensity (OBSI) method was used to test noise levels in three types of porous asphalt pavement structures and on a dense graded easy compact asphalt concrete (ECA) for comparison. The progressions of the medium-term performances were analyzed according to the measured results. The correlations between tire/pavement noise levels and testing speed, testing lane, pavement structure, and road condition indicators were investigated by regression. The research results revealed that the DR and SFC of the three types of porous asphalt pavement displayed more significant attenuation in the service period, while the IRI and RD showed small changes. Among them, the SFC demonstrated significant attenuation over the first 4 years, decreasing between 13.8% and 17.0%. From the 3-7 years of operation, the transverse crack disease in porous asphalt pavement progressed rapidly. The three porous asphalt pavement structures tested exhibited commendable noise reduction capabilities. Compared to ECA, the OBSI noise levels of these structures were lower by 2.09 dB, 1.53 dB, and 2.88 dB, respectively. Compared to other pavement condition indicators, RD had a more significant impact on the OBSI value of the PUC-10 porous asphalt pavement. For the PUC-10+PAC-13 porous asphalt pavement, there was a significant linear relationship between the OBSI value and SFC, mainly due to polishing of the coarse aggregate surface. It leads to a decrease of the micro-texture, which lies in increasing tire/pavement noise at high-frequency ranges and decreasing SFC. This study will have guiding significance for the research of the attenuated law and durability improvement of porous asphalt tire/pavement noise.

The energy E takes the place of the gravitational mass m_G to produce gravity [1]. We wonder whether the inertial mass m_i in the inertial force is also replaced by E. The experiments to measure the inertial force and weight of a carrier are presented. Now we can test the principle of equivalence and study foundations of physics in condensed matter.

The thesis proposes a argument that a mass point moving in a horizontal circle on the Earth's surface can generate a radial centrifugal force of the Earth's center of mass, thus realizing an unconventional anti-gravity path. And through the theoretical analysis of the difference in the distribution of gravitational acceleration at different latitudes caused by the rotation of the earth, and the centrifugal force of a mass point moving in a horizontal circle on the earth's surface is analyzed, the validity of the argument is demonstrated. At the same time, the paper puts forward two possible basic principles, and makes theoretical analysis and demonstration. Conceive of the concrete experimental verification of principle two is proposed. Four technical schemes for antigravity ascent are proposed and basic analysis is made. On the premise of not fully considering the practical technical ability, it is theoretically proved that three of them have realistic operability and development potential. In theory, this paper opens up a different way of anti-gravity for human beings, which will bring new ideas and prospects for human beings to get rid of the bondage of gravity.

In this paper, the Hafele‐Keating experiment and the geostationary orbit satellite of related physics problems of are analyzed and discussed in detail. If researchers read the paper and think about it, It will be found that the Hafele‐Keating experiment and the geostationary satellite problem prove that some of the core ideas and theories of relativity are seriously wrong. Isnʹt that a very serious problem in physics? Canʹt this cause the academic circles to pay great attention to it? Isnʹt this worthy of in‐depth analysis and research? The core of the paper is to point out that there are problems with the space concept and the reference system theory of classical physics and relativity, And that would bring up a whole host of physics problems. It takes a concerted effort from the academic community, Do furtherin‐depth analysis and research. Strive forthe further discovery and perfection of physics theory.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

Glycosaminoglycans (GAGs) with unique structures from marine animals show intriguing pharmacological activities and negligible biological risks, providing more options for us to explore safer agents. Swim bladder is a tonic food and folk medicine, and its GAGs show good anticoag-ulant activity. In this study, two GAGs SJG-1.0 and GMG-1.0 have been extracted and isolated from the swim bladder of Sphyraena jello and Gadus morhua. The physicochemical properties, pre-cise structural characteristics, and anticoagulant activities of these GAGs were determined. The analysis results of the SJG-1.0 and GMG-1.0 showed that they were chondroitin sulfate (CS)/dermatan sulfate (DS) hybrid chains with molecular weights of 109.32 kDa and 123.13 kDa, respectively. They were mainly composed of the repeating disaccharide unit of -{IdoA-α1,3-GalNAc4S-β1,4-}- (DS-A). The DS-B disaccharide unit of -{IdoA2S-α1,3-GalNAc4S-β1,4-}- also existed in both SJG-1.0 and GMG-1.0. SJG-1.0 had a higher proportion of CS-O disaccharide unit -{-GlcA-β1,3-GalNAc-β1,4-}-, while GMG-1.0 contained higher proportion of CS-E disaccha-ride unit -{-GlcA-β1,3-GalNAc4S6S-β1,4-}-. The disaccharide compositions of the GAGs varied in a species-specific manner. Anticoagulant activity assay revealed that both SJG-1.0 and GMG-1.0 had potent anticoagulant activity, which can significantly prolong activated partial thrombosis time. GMG-1.0 also can prolong the thrombin time. SJG-1.0 showed no intrinsic tenase inhibition ac-tivity, while GMG-1.0 can obviously inhibit intrinsic tenase with EC50 of 58 nM. Their significantly different anticoagulant activities may be due to their different disaccharide structural units and proportions. These findings suggested that the swim bladder CS/DS hybrid chains with well-defined structure may be safer anticoagulants with low bleeding risk.

In (Semigroup Forum 77: 325-338, 2008) Mahmoudi M. and Renshaw J. solved a study that covers of cyclic $S$-acts over monoids. This article is an attempt to initiate the covers of finitely generated $S$-acts. We give a necessary and sufficient condition for a monoid to have the properties that $n$-generated $S$-acts have strongly flat covers, Condition $(P)$ covers and projective covers. The main conclusions extend some known results. We show also that Condition $(P)$ covers of finitely generated $S$-acts are not unique, unlike the situation for strongly flat covers. Additionally, we demonstrate that the property of Enochs' $\mathcal{X}$-precover of $S$-act $A$, where $\mathcal{X}$ denotes a class of $S$-acts that are closed under isomorphisms.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

After the end of colonial rule in 1997, the Hong Kong education system has been experiencing a policy reform on Senior Secondary Education (NSS) Curriculum commenced in September 2009 aiming to educate students as globalized Hong Kong citizens for the Western. Although previous scholars argued that it is hard to differentiate between domestic values and the Western values in account of curriculum development (Sewpaul, 2007), this study demonstrates an analysis using the dichotomy to investigate how local curriculum, especially in the post-colonial areas, embrace both the Western values and domestic values. Using content analysis on the NSS curriculum guides, this article evaluates the influence of the Western values and Chinese values in the NSS curriculum through investigating: (1) how the Western values and Chinese values was incorporated into the curriculum throughout its development (2) why some values are more significantly highlighted in the curriculum guide. Findings include that more Chinese values are involved in the curriculum documents. This may be because of the upholding of domestic values as a post-colonial city. The Western values which are academically related are greatly incorporated into the local curriculum.

A PLS-based quality prediction method is proposed for batch processes using two-dimensional extended windows. To realize the adoption of information in the direction of sampling time and batch, a new definition region of support (ROS), k-i-back-extended region of support (KIBROS), is proposed to establish the extended window, which including the data of the previous sampling times in the same batch, the data of the same sampling time in the historical batches, the data of the previous sampling times in the historical batches and the data of the later sampling times in the historical batches. According to these regions of support, extended windows are established, and different models are proposed based on the extended windows for batch processes quality prediction. Further, using a typical batch process as an example, the injection molding process, the proposed quality prediction method is experimentally verified, proving that the proposed methods have higher prediction accuracy than the traditional method and the prediction stability is also improved.

The intense motion of a ship can greatly impacts the comfort of crew members and the safety of the vessel. Therefore, accurately estimating and predicting ship attitudes has become an important issue. This paper introduces the latest development in functional deep learning model called DeepOnet. It takes wave height as input and ship motion as output, using a cause-to-result prediction approach. The modeling data used in this study is sourced from publicly available experimental data from the Iowa Institute of Hydraulic Research. Firstly, parameters system tuning was conducted for the neural network's hyperparameters to determine the appropriate combination of parameters. Secondly, the DeepOnet model for wave height and multi-degree-of-freedom motion was established, and the influence of increasing time steps on prediction accuracy was examined. Finally, a comparison was made between the DeepOnet model and the classical time series model LSTM. It was found that the DeepOnet model had a 10-fold improvement in accuracy for roll and heave attitudes. Moreover, as the forecast duration increased, the advantage of DeepOnet showed a trend of strengthening. As a functional prediction model, DeepOnet provides a new promising tool for very short-term prediction of ship motion.

With the rapid development of earth observation, satellite navigation, mobile communication and other technologies, the order of magnitude of the spatial data we acquire and accumulate is increasing, and higher requirements are put forward for the application and storage of spatial data. Under this circumstance, a new form of spatial data organization emerged-the global discrete grid. This form of data management can be used for the efficient storage and application of large-scale global spatial data, which is a digital multi-resolution the geo-reference model that helps to establish a new model of data association and fusion. It is expected to make up for the shortcomings in the organization, processing and application of current spatial data. There are different types of grid system according to the grid division form, including global discrete grids with equal latitude and longitude, global discrete grids with variable latitude and longitude, and global discrete grids based on regular polyhedrons. However, there is no accuracy evaluation index system for remote sensing images expressed on the global discrete grid to solve this problem. This paper is dedicated to finding a suitable way to express remote sensing data on discrete grids, and establishing a suitable accuracy evaluation system for modeling remote sensing data based on hexagonal grids to evaluate modeling accuracy. The results show that this accuracy evaluation method can evaluate and analyze remote sensing data based on hexagonal grids from multiple levels, and the comprehensive similarity coefficient of the images before and after conversion is greater than 98%, which further proves that the availability hexagonal grid-based remote sensing data of remote sensing images. And among the three sampling methods, the image obtained by the nearest interpolation sampling method has the highest correlation with the original image.

This paper describes the formulations for viscoplasticity of metals based on the Chaboche and Delobelle model. The implementations of the viscoplastic models were detailed herein and then implemented via user subroutines for material models (UMAT) in ABAQUS. Two typical metals, i.e., 316 Stainless Steel and Zircaloy-4, were chosen as examples and their viscoplastic behaviors were captured. Numerical simulations are compared to reported experiments to validate the models and the UMAT codes. Typical viscoplastic behaviors of both metals, such as stress relaxation and creep, were captured well against available experiments. We publicize all the data and codes via: https://github.com/XJTU-Zhou-group/ABAQUS_UMAT_316ss_Zr4.

This paper considers the Hermitian solutions of a new system of commutative quaternion matrix equations, we establish both necessary and sufficient conditions for the existence of solutions. Furthermore, we derive an explicit general expression when it is solvable. To illustrate our main findings, we present two numerical algorithms and examples in this paper.

The gravitational charge should be the energy instead of mass. This modification will lead to some different results and the experiments to test are also presented. Especially, we propose a scheme to achieve the negative energy and gravitational repulsive force in the lab.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

Desert ecosystem occupies an important position in the composition of global biodiversity. The Tarim Basin locates in south Xinjiang of China and has the world 's second largest mobile desert, the Taklamakan Desert. As an endemic species in this region, Phrynocephalus forsythii has been demonstrated with potential high extinction risk to climate change. In order to understand the overall genetic status and provide accordant conservation strategies of the species, we investi-gated the genetic diversity and population structure of P. forsythii from 15 sites in the Tarim Basin using 21 highly polymorphic microsatellite markers. We found significant genetic structure across the study region. We also revealed generally low levels of gene flow between the 25 sites, sug-gesting individual dispersal and migration may be restricted within populations. In addition, geographical distance and ambient temperature might be important factors in explaining the observed genetic structure. Our results will provide scientific basis for the future protection of P. forsythii in this area, as well as an important reference for the conservation and management of biodiversity in desert ecosystems.

Predicting and evaluating the vitality level of public spaces of urban design is crucial before new construction and renewal, especially for developing countries, to avoid failures like "ghost neighborhood" and reduce resource waste. However, existing assessment methods for the urban vitality are either static and ignore changes in the time dimension, or rely on historical big data and are unable to predict unbuilt projects. This study combines previous methods and crowds’ characteristics observation in public space, puts forward the crowd-frequency hypothesis and constructs an algorithm, and establishes a time-dimensional urban vitality dynamic prediction model. Taking the Rundle Mall neighborhood in Adelaide, Australia, as an example, the effec-tiveness of the prediction model was proved through on-site observation sampling comparative verification method. In addition, the decision tree model was used to conduct machine learning on the case data, and a set of algorithm programs were obtained that can directly input some basic information to obtain the urban vitality level (high-medium-low) in a certain period. It can be used as a tool to support the design and decision-making processes of urban planners and government officials, providing a low-cost way to achieve sustainable urban vitality construction of late-developing cities directly.

The quantified residence time distribution (RTD) provides a numerical characterization of mixing in the continue casting tundish, thus allowing the engineer to better understand the metallurgical performance of the reactor. This paper describes a computational fluid dynamic (CFD) modelling study for analyzing the flow pattern and the residence time distribution in a five-strand tundish. Two passive scalar transport equations are applied to separately calculate the E-curve and F-curve in the tundish. The numerical modelling results are compared to the water modelling results for the validation of the mathematical model. The volume fraction of different flow regions (plug, mixed and dead) and the intermixing time during the ladle changeover are calculated to study the effects of the flow control device (FCD) on the tundish performance. The result shows that a combination of the U-baffle with deflector holes and the turbulence inhibitor has three major effects on the flow characteristics in the tundish: i) reduce the extent of the dead volume; ii) evenly distribute the liquid streams to each strand and iii) shorten the intermixing time during the ladle changeover operation.

Marine soft corals are prolific sources of various natural products that have served as a wealthy reservoir of diverse chemical scaffolds for new drug leads. The genus Litophyton contains almost 100 species but only a small part of them had been classified and chemically investigated, which calls for more attentions from the global researchers. In the current work, 109 secondary metabolites have been discussed based on published data from 1975 to July, 2023, covering a period of near five decades. The studied species of the genus Litophyton inhabited various tropical and temperate regions and afforded a variety of biologically active natural products such as terpenes, steroids, alkaloids, and lipids. A wide spectrum of pharmacological effects of these compounds had been evaluated, including cytotoxic, anti-HIV, antibacterial, antifungal, anti-malarial, antifeedant, molluscicidal, PTP1B inhibitory, and insect growth inhibitory activities. This review aims to provide an up-to-date literature survey and comprehensive insight into chemical structures, taxonomical distributions, and biological activities of the reported metabolites from the title genus whenever available.

Adipose tissue composition contributes greatly to the quality and nutritional value of meat. Transcriptomic and lipidomic techniques were used to investigate the molecular mechanism of fat deposition difference among Ningxiang, Berkshire and F1 pigs. Transcriptomic analysis identified 680, 592 and 380 differentially expressed genes (DEGs) by comparing the groups of Ningxiang pigs vs Berkshire pigs, Berkshire pigs vs F1 pigs, Ningxiang pigs vs F1 pigs. Lipidomic analysis screened 423, 252, and 50 significantly changed lipids (SCLs) by comparing the groups of Ningxiang pigs vs Berkshire pigs, Berkshire pigs vs F1 pigs, Ningxiang pigs vs F1 pigs. Lycine, serine and threonine metabolism pathway, fatty acid biosynthesis and metabolism related pathways were siginificant enriched in the groups of Berkshire pigs vs Ningxiang pigs and Berkshire pigs vs F1 pigs. The DEGs (PHGDH, LOC110256000) and the SCLs (Phosphatidylserines) may have a great impact on lycine, serine and threonine metabolism pathway. Moreover, the DEGs (FASN, ACACA, CBR4, SCD, ELOV6, HACD, CYP3A46, CYP2B22, GPX1, GPX3) and the SCLs (palmitoleic acid, linoleic acid, arachidonic acid, icosadienoic acid) play important role in fatty acid biosynthesis and metabolism. Thus, the fat deposition difference among Ningxiang, Berkshire and F1 pigs may be caused by the difference of the expression pattern of key genes in multiple enrichment KEGG pathways. The research presented multiple lipids that were potentially available biological indicator and screened key genes that were potentially gene targets for molecular design breeding. The research also explored the molecular mechanisms of fat deposition difference among Ningxiang, Berkshire and F1 pigs and provides insight into the selection of backfat thickness and fat composition of adipose tissue for future breeding strategies.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Given the increased provision of international exchange programmes in higher education, this paper examines students’ perceptions of their learning process in one Erasmus+ programme in Food Innovation and Product Design. Using evaluation model of international exchange programme and triple helix model as the analytical framework, students’ testimonials from 2015–2021 were analysed using a critical discourse analysis. EU and non-EU students had similar perceptions of learning outcomes related to knowledge of the food innovation industry, but non-EU students had a stronger sense of awareness of both the international context and multicultural interaction.

Trace metals can enter some natural regions with low human disturbance from atmospheric circulation, but little information is available regarding how the canopy can retained trace metals. Therefore, a representative sub-alpine spruce plantation was selected to investigate the net throughfall fluxes of eight trace metals (Fe, Mn, Cu, Zn, Al, Pb, Cd and Cr) of closed canopy and gap-edge canopy from August 2015 to July 2016. Over a one-year observational period, the annual fluxes of Al, Zn, Fe, Mn, Cu, Cd, Cr and Pb were 7.29 kg·ha^-1, 2.30 kg·ha^-1, 7.02 kg·ha^-1, 0.16 kg·ha^-1, 0.19 kg·ha^-1, 0.06 kg·ha^-1, 0.56 kg·ha^-1 and 0.24 kg·ha^-1, respectively, in the deposited precipitation. The annual net throughfall fluxes of these trace metals were 1.73 kg·ha^-1, 0.9 kg·ha^-1, 1.68kg·ha^-1, -0.032 kg·ha^-1, 0.04 kg·ha^-1, 0.018 kg·ha^-1, 0.093 kg·ha^-1 and 0.087kg·ha^-1, respectively, in the gap-edge canopy and -1.6 kg·ha^-1, 1.13 kg·ha^-1, 1.65 kg·ha^-1, -0.10 kg·ha^-1, 0.05 kg·ha^-1, 0.03 kg·ha^-1, 0.26 kg·ha^-1 and 0.15 kg·ha^-1, respectively, in the closed canopy. The closed canopy displayed a greater filter effect on the trace metals from precipitation than did the gap-edge canopy in the sub-alpine forest. In the rainy season, the net filtering ratio of trace metals ranged from -66%-89% in the closed canopy and from -52% to 25% in the gap-edge canopy. However, the net filtering ratio of all trace metals was greater than 50% in the closed canopy in the snowy season. Therefore, the results suggested that the most trace metals moving through the forest canopy are taken up rather than by rainfall leaching; moreover, the closed canopy can efficiently take up trace metals in the snowy season.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

Saliency detection in synthetic aperture radar (SAR) image is a difficult problem. This paper proposed a multitask saliency detection (MSD) model for the saliency detection task of SAR image. Firstly, we extract four features of SAR image as the input of the MSD model, which include the intensity, orientation, uniqueness and global contrast. Then, the saliency map is generated by the multitask sparsity pursuit (MTSP) which integrates the multiple features collaboratively. Subjective and objective evaluation of the MSD model verifies its effectiveness. Based on the saliency maps of the source images, an image fusion method is proposed for the SAR and color optical image fusion. The experimental results of real data show the proposed image fusion method is superior to the presenting methods in terms of several universal quality evaluation indexes, as well as in the visual quality. The salient areas in the SAR image can be highlighted and the spatial and spectral details of color optical image can also be preserved in the fusion result.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Fire is a common natural disturbance in forest ecosystems and plays an important role in subsequent vegetation patterns. Based on the spatial sequence method instead of the time successional sequence method, this study selected burned areas in different locations in the Anning River Basin, which contains typical dry valleys. Quadrat surveys and quantitative classification were used to identify the vegetation classification, distribution pattern, and environmental interpretation during the natural restoration process after forest fire. The results showed that: (1) the vegetation community in the early stage of natural recovery after forest fire disturbance could be divided into seven community types, and Quercus guyavaefolia H. Leveille (Qg) was the dominant species in the community; (2) vegetation samples could be divided into five ecological types, and the classification and distribution pattern of community types in this region changed most obviously with altitude; and (3) detrended correspondence analysis could clearly classify vegetation community types, and detrended canonical correspondence analysis could well reveal the relationships between species and environmental factors. This study provides a scientific basis guiding the restoration of ecosystem structural stability and biodiversity in burned areas.

Smart air filters are beneficial to provide highly efficient particle removal, treat multiple contaminants simultaneously and conserve energy during air filtration processes. Herein, a type of self-supporting smart air filter (SSSAF) was fabricated by sandwiching the VOC-responsive PZT/PVDF electrospun membrane with two metal mesh electrodes. Besides the high filtration efficiency for sub-micron particles, the SSSAF showed good responses to pressure drop in the range of 0 to 500 Pa via the electroactivity of PZT/PVDF membrane. In addition, the SSSAF achieved VOC sensing function via the swelling properties of PZT/PVDF membrane in organic vapors, demonstrated by its signal to 50 to 200 ppm ethanol gases. The SSSAF based nanogenerator was employed to harvest wind energy, which was further applied to inhibit bacterial growth without the need of additional power input. The results provide new insight into development of all-in-one smart air filters.

Photoacoustic imaging (PAI) is a cutting-edge biomedical imaging modality, providing detailed anatomical and functional information about the area beneath the skin surface. Its light energy deposition is such that PAI typically provides clear images of the skin with high signal-to-noise ratios. Specifically, the rich optical contrast of PAI allows biological information related to lesion growth, malignancy, treatment response, and prognosis to be seen. Given its significant advantages and emerging role in imaging skin lesions, we summarize and comment on representative studies of skin PAI, such as the guidance of skin cancer biopsies and surgical excisions, and the accurate diagnosis of psoriasis. We conclude with our insights about the clinical significance of skin PAI, showing how its use to identify biological characteristics in lesion microenvironments allows early diagnosis and prognosis of disease.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

As the global population rapidly ages with longer life expectancy and declining birth rates, the need for healthcare services and caregivers for older adults is increasing. Current research envisions addressing this shortage by introducing domestic service robots to assist with daily activities. The successful integration of robots as domestic service providers in our lives requires them to possess efficient manipulation capabilities, provide effective physical assistance, and have adaptive control frameworks that enable them to develop social understanding during human-robot interaction. In this context, human factors, especially quantifiable ones, represent a necessary component. The objective of this paper is to conduct an unbiased review encompassing studies on human factors studied in research involving physical interactions and strong manipulation capabilities. We identified the prevalent human factors in physical human-robot interaction (pHRI), noted the factors typically addressed together and determined the frequently utilized assessment approaches. Additionally, we gathered and categorized proposed quantification approaches based on measurable data for each human factor. We also formed a map of common contexts and applications addressed in pHRI for a comprehensive understanding and easier navigation of the field. We found out that most of the studies in direct pHRI (when there is direct physical contact) focus on social behaviors with belief being the most commonly addressed human factor type. Task collaboration is moderately investigated, while physical assistance is rarely studied. In contrast, indirect pHRI (when the physical contact is mediated via a third item) studies often involve industrial settings, with physical ergonomics being the most frequently investigated human factor. More research is needed on human factors in direct and indirect physical assistance applications, including studies that combine physical social behaviors with physical assistance tasks. We also found that while the predominant approach in most studies involves the use of questionnaires as the main method of quantification, there is a recent trend that seeks to address quantification approaches based on measurable data.

In this paper, a new approach is proposed for designing ultra-low-power FFT (Fast Fourier Transform) system suitable for use in energy harvesting powered sensors. Bit-serial architecture is adopted to reduce the power consumption of butterfly operation. Simulation results show that, compared with state-of-the-art bit-serial and conventional parallel processors, the proposed technique is superior in terms of silicon area, power consumption, dynamic energy use due to variable precision arithmetic. A sample design of a 64-point FFT shows that the implementation can save about 40% area and 36% leakage power compared with a conventional parallel counterpart, accordingly achieving significant power benefits at a low sample rate and low voltage domain. The dynamic variation of the arithmetic precision can be achieved through a simple modification of the controller with hardware area overhead of 10% gate count.

China is in the climbing phase of the "Inverted U" environmental Kuznets curve, from excessive environmental consumption to the development stage of governance and protection, and green innovation. It is the most complex period of environmental quality. Environmental and policy regulation are very important. Select panel data of 29 provinces of China (excluding Hong Kong, Macau, Taiwan, Hainan and Tibet) from 2008 to 2017, construct a nonlinear two-threshold regression model, empirically analyse the impact of environmental tax and government innovation subsidies to green processes innovation, and attempt to explore whether the implementation of these two policies at the same time can make enterprises more inclined to green process innovation and whether there is an optimal space for policy implementation. It is proposed that the synergy effect of environmental tax and government innovation subsidy policies on enterprise green process innovation should be fully utilized, and the enterprise green process innovation environment and incentive mechanism should be improved to promote the green transformation and sustainable development of enterprises.

Cellular senescence has recently been recognized as a hallmark of cancer, reflecting its association with aging and inflammation, its role as a response to deregulated proliferation and oncogenic stress, and its induction by cancer therapies such as radiation, chemotherapy, and targeted agents. While such therapy-induced senescence (TIS) has been linked to resistance, recurrence, metastasis and normal tissue toxicity, TIS has the potential to enhance therapy response and stimulate anti-tumor immunity. In this review, we examine the Jekyll and Hyde nature of senescent cells (SnCs), with a particular focus on how their persistence while expressing the senescence-associated secretory phenotype (SASP) modulates the tumor microenvironment through autocrine and paracrine mechanisms. Via the SASP, the formation of SnCs may alternately mediate resistance or response to conventional therapy. Further, toward fulfilling the unmet potential of cancer immunotherapy, we consider how SnCs may influence tumor inflammation and serve as a source of antigen to potentiate anti-tumor immunity. This new view suggests treatment strategies based on inducing TIS to enhance immune checkpoint blockade. Finally, we describe strategies for mitigating the detrimental effects of senescence, such as modulating the SASP or targeting SnC persistence, toward enhancing the benefits of cancer treatment.

In recent years, there has been significant growth in the ubiquity and popularity of three dimensional(3D) point clouds, with an increasing focus on the classification of 3D point clouds. To extract richer features from point clouds, many researchers have turned their attention to various point set regions and channels within irregular point clouds. However, this approach has limited capability in attending to crucial regions of interest in 3D point clouds and may overlook valuable information from neighboring features during feature aggregation. Therefore, this paper proposes a novel 3D point cloud classification method based on global attention and adaptive graph convolution. The method consists of two main branches: the first branch com-putes attention masks for each point, while the second branch employs adaptive graph convolu-tion to extract global features from the point set. It dynamically learns features based on point interactions, generating adaptive kernels to effectively and precisely capture diverse relationships among points from different semantic parts. Experimental results demonstrate that the proposed model achieves 93.8% in overall accuracy and 90.8% in average accuracy on the ModeNet40 dataset.

In this paper, we study the well-posedness and asymptotic behaviour of solutions to a laminated beam in thermoelasticity of type III. We first give the well-posedness of the system by using the semigroup method. Then, we show that the system is exponentially stable under the assumption of equal wave speeds. Furthermore, it is proved that the system is lack of exponential stability for case of nonequal wave speeds. In this regard, a polynomial stability result is proved.

Increasing attention has been paid to the potential probiotic effects of Latilactobacillus sakei. To explore the genetic diversity of L. sakei, 14 strains isolated from different niches (feces, fermented kimchi and meat products) and 54 published strains were compared and analyzed. The results showed that the average genome size and GC content of L. sakei were 1.98Mb and 41.22%, respectively. Its core genome mainly encodes translation and transcription, amino acid synthesis, glucose metabolism and defense functions. L. sakei has an open pan-genomic characteristics, and its pan-gene curve shows an upward trend. L. sakei has open pan-genome feature, and its pan-genome curve is on the rise. The genetic diversity of L. sakei is mainly reflected in carbohydrate utilization, antibiotic tolerance, and immune/competition-related factors, such as clustering regular interval short palindromic repeat sequence (CRISPR)-Cas. The CRISPR system is mainly IIA type, and a few are IIC types. This work provides a basis for the study of this species.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

The exploration and identification of targets and pathways for Atopic dermatitis (AD) treatment and diagnosis are critical for AD control. The conventional target exploration approach such as the literature review is not satisfying in terms of efficiency and accuracy. Recently, the bioinformatic approach is drawing attention for its unique advantage of high-volume data analysis for target and pathway exploration; Open Targets Platform is the targets source for this study to extract top 200 high-rank proteins from 3122 AD associated proteins. STRING, Cytoscape, CytoHubba, ClueGo, and CluePedia function had been applied for data analysis. The KEGG Mapper search & colour pathway was the pathway map resource for identified pathways; 23 key hub genes (VDR, KIT, BCL2L11, NFKBIA, KRAS, IL13, JAK2, STAT3, IL21, IL4R, REL, PDGFRB, FOXP3, RARA, RELB, EGFR, IL21R, MYC, CREBBP, NR3C1, IL2, JAK1, and KITLG). Additionally, 8 correlated pathways and the biological process had been identified; Through this study, a viable approach for target and pathway exploration had been presented. The identified AD targets and pathways will be tested for upcoming research for traditional Chinese medicinal herb interactions

The recyclable paper based on photochromic materials not only reduces the pollution in the paper manufacture process, but also reduces the pollution caused by the use of ink, which receives wide attention. In this paper, a serial of PMoA-PWA/ZnO/PVP hybrid films which had different ratio of PMoA/PWA was prepared by the ultrasonic composite method. The results indicated that the hybrid film prepared when the ratio of PMoA to PWA was 3 had the best photochromic performance. In this system, ZnO was the photosensitizer while PMoA/PWA was the chromophore. The photochromic mechanism of PMoA-PWA/ZnO/PVP hybrid film was based on the photogenerated electron transfer mechanism. ZnO generated photoelectron under the excitation of visible light, then PMoA and PWA obtained the photoelectron and produced photoreduction reaction to generate heteropolyblue. The visible light photochromic paper was prepared by loaded PMoA-PWA/ZnO/PVP hybrid film (A3) on A4 paper. Application test showed that the prepared paper had extremely stable, excellent and reversible visible light photochromic properties, whether it was printing patterns or words and could replace the ordinary paper to realize the reuse of paper.

Spermatogonial stem cells (SSCs) are the only primitive spermatogonial cells in males that can naturally transmit genetic information to their offspring and replicate throughout their lives. Phospholipase D family member 6 (PLD6) has recently been found to be a surface marker for SSCs in mice and boars; however, it has not been validated in cattle. The results of RT-PCR and qRT-PCR found that the relative expression of PLD6 gene in the testicular tissues of 2-year-old Simmental calves was significantly higher than that of 6-month-old calves. Immunofluorescent staining further verified the expression of PLD6 protein in bovine spermatogenic cells like germ cell marker VASA. Based on multiple bioinformatic databases, PLD6 is a conservative protein which has high homology with mouse Q5SWZ9 protein. It is closely involved in the normal functioning of the reproductive system. Molecular dynamics simulation analyzed the binding of PLD6 as a phospholipase to cardiolipin (CL), and PLD6-CL complex showed high stability. The protein interaction network analysis showed that there is a significant relationship between PLD6 and piRNA binding protein. PLD6 acts as an endonuclease and participates in piRNA production. In addition, PLD6 in bovine and mouse testes has a similar expression pattern with the spermatogonium-related genes VASA and PIWIL2. In conclusion, these analyses imply that PLD6 has a relatively high expression in bovine testes and could be used as a biomarker for spermatogenic cells including SSCs.

The data assimilation method to improve sea fog forecast over the Yellow Sea is usually three-dimensional variational assimilation (3DVAR), whereas ensemble Kalman filter (EnKF) has not yet been applied on this weather phenomenon. In this paper, two sea fog cases over the Yellow sea, one spread widely and the other spread narrowly along the coastal area, are studied in detail by a series of numerical experiments with 3DVAR and EnKF based on the Grid-point Statistical Interpolation (GSI) system and the Weather Research and Forecasting (WRF) model. The results show that the assimilation effect of EnKF outperforms that of 3DVAR: for the widespread-fog case, the probability of detection and equitable threat scores of the forecasted sea fog area get improved respectively by ~57.9% and ~55.5%; the sea fog of the other case completely mis-forecasted by 3DVAR is produced successfully by EnKF. These improvements of EnKF relative to 3DVAR are benefited from its flow-dependent background error, resulting in more realistic depiction of sea surface wind for the widespread-fog case and better moisture distribution for the other case in the initial conditions. More importantly, the correlation between temperature and humidity in the background error of EnKF plays a vital role in the response of moisture to the assimilation of temperature, which leads to a great improvement on the initial moisture conditions for sea fog forecast.

Orogenic antimony-gold deposits contribute significantly to the global antimony resource base. China's orogenic antimony-gold deposits are primarily in southern Tibet. Investigations indicate that antimony combines and migrates with sulfur hydroxides in ore-forming fluids. Previous research on fluid inclusions in orogenic antimony-gold ores with sedimentary rock accommodation revealed the presence of organic inclusions, including liquid hydrocarbons, alongside common components such as CO2, H2O, CH4, and NaCl. However, the impact of liquid hydrocarbons on antimony migration and mineralization is still de-batable. To investigate the transportability of antimony by liquid hydrocarbons in orogenic antimony ores, we selected n-dodecanethiol and n-dodecane as the subjects. We measured the solubility and occurrence form of antimony in these compounds at various temperatures and durations. The results indicate that after 5 and 10 days of reaction at 100 °C, the antimony concentrations in the n-dodecanethiol and n-dodecane groups were 67.44±7.62 ppm, 75.15±16.74 ppm, 1.40±1.02 ppm, and 3.02±3.09 ppm, respectively. At 150 °C for 5 and 10 days, the respective concentrations were 50.58±5.39 ppm, 77.26±45.20 ppm, 2.66±3.08 ppm, and 2.41±2.03 ppm. At 200 °C for 5 and 10 days, the corresponding concentrations were 339.76±71.94 ppm, 218.97±25.03 ppm and 6.53±7.17 ppm, 2.27±0.82 ppm (n=3). The measured solubility of antimony in the n-dodecanethiol group increased gradually with rising temperature. The solubility of antimony in the n-dodecane group was low and notably inferior to that observed in the n-dodecanethiol group. X-ray photoelectron spectroscopy (XPS) analysis demonstrated a distinct thiol (R-SH) peak at 163.31 eV and compound peaks of antimony reacting with thiols at 162.06 and 160.87 eV. This suggests that antimony predominantly forms complexes with thiols for migration. Our findings suggest that specific liquid hy-drocarbon components, predominantly thiols, can interact with antimony at metallogenic temperatures and persist in ore-forming fluids, facilitating migration and mineral enrichment. Earlier experimental studies on gold and crude oil have indicated that liquid hydrocarbons also play an essential role in the transportation and enrichment of gold during the formation of gold deposits, thus indicating that liquid hydrocarbons possess the considerable potential to act as an ore-forming fluid during orogenic antimony-gold deposit formation in southern Tibet.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

Bipedal locomotion remains one of the major open challenges of humanoid robotics. The common approaches are based on simple reduced model dynamics to generate walking trajectories, often neglecting the whole-body dynamics of the robots. As motions in nature are often considered as optimal with respect to certain criteria, in this work we present an optimal control based approach that allows us to generate optimized walking motions using a precise whole-body dynamic model of the robot, in contrast with the common approaches. The optimal control problem is formulated to minimize a set of desired objective functions with respect to physical constraints of the robot and contact constraints of the walking phases. We apply the method with combinations of different objective criteria to the model of a reduced version of the iCub humanoid robot of 15 internal DOF. The obtained trajectories are executed on the real robot and we carry out a discussion on the differences between the outcomes of this approach with the classic approaches.

This paper is based on the concept of absolute airspace and its local absolute stationary reference system proposed by the author, on the premise of abandoning space concept and the relativity principle of relativity theory, It is proposed that general relativity and special relativity can be unified into Simple and practical a space-time transformation theory which fully includes other basic physical principles of relativity. And the unified and simple expression of the time transformation effect is proved and deduced. By comparing with the theoretical derivation and checking calculation of Hafele-Keating experiment in an ideal state, It is proved that the expression of time transformation effect proposed in this paper is completely correct. Compared with the theory of relativity, the calculation is simpler and more accurate. The paper also puts forward two checking prediction of physical cases about the time transformation effect, which are left for the capable competent unit or individual to verify in practice.

With the aging of China's population, the problem of pension security has become more and more prominent, and whether delayed retirement can effectively alleviate the pension fund gap and ensure the sustainability of the pension fund has become the focus of social concern. This study predicts the income and expenditure of urban workers' basic pension insurance fund from 2021 to 2050 by constructing an actuarial model of pension insurance fund income and expenditure, and simulates the effect of delayed retirement policy. The prediction results show that under the existing system, the basic pension insurance fund for urban workers will have a shortfall for the first time in 2027, and the shortfall will expand year by year. Compared with the non-implementation of delayed retirement policy, the simulation of the implementation of delayed retirementt program delayed the emergence of the fund gap until 2029, and the forecast period of the pension fund gap significantly narrowed, indicating that delayed retirement policy has a certain positive impact on alleviating the pressure of pension payments, but delayed retirementt can not completely eliminate the pension fund gap. In view of this, this paper suggests that a progressive and flexible delayed retirement policy should be introduced as soon as possible to better adapt to the needs of different groups. At the same time, differentiated policies should be formulated for different groups of people and a pension incentive mechanism for delayed retirement should be set up to improve public acceptance of delayed retirement policy. In addition, delayed retirement policy should be combined with other measures, such as lowering the corporate contribution rate and enhancing the value-added capacity of the pension fund, so as to ensure the sustainability of the pension fund.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

Complexity science studies physical phenomena that cannot be explained by the mere analysis of the single units of a system but requires to account for their interactions. A feature of complexity in connected systems is the emergence of mesoscale patterns in a geometric space, such as groupings in bird flocks. These patterns are formed by groups of points that tend to separate from each other, creating mesoscale structures. When multidimensional data or complex networks are embedded in a geometric space, some mesoscale patterns can appear respectively as clusters or communities, and their geometric separability is a feature according to which the performance of an algorithm for network embedding can be evaluated. Here, we introduce a framework for the definition and measure of the geometric separability (linear and nonlinear) of mesoscale patterns by solving the travelling salesman problem (TSP), and we offer experimental evidence on embedding and visualization of multidimensional data or complex networks, which are generated artificially or are derived from real complex systems. For the first time in literature the TSP’s solution is used to define a criterion of nonlinear separability of points in a geometric space, hence redefining the separability problem in terms of the travelling salesman problem is an innovation which impacts both computer science and complexity theory.

While numerous studies have explored the correlation between the built environment and ride-hailing demand, few have assessed their nonlinear interplay. Utilizing ride-hailing order data and multi-source built environment data from Nanjing, China, this paper uses the machine learning method, eXtreme Gradient Boosting (XGBoost), combined with SHapley Additive exPlanations (SHAP) and Partial Dependence Plots (PDP) to investigate the impact of built environment factors on ride-hailing travel demand, including their non-linear and threshold effects. The findings reveal that dining facilities have the most significant impact, with a contribution rate of 30.75%, on predicting ride-hailing travel demand. Additionally, financial, corporate, and medical facilities also exert considerable influence. The built environment factors need to reach a certain threshold or within a certain range to maximize the impact of ride-hailing travel demand. population density, land use mix and distance to the subway station collectively influence ride-hailing demand. The results are helpful for TNCs to allocate network ride-hailing resources reasonably and effectively.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

Modern war is sudden and rapid, and once the battle starts, the demand for equipment maintenance and guarantee will show an outburst situation, which puts equipment maintenance and guarantee capability to a severe test. To accurately grasp the civil-military integration of aviation maintenance and guarantee capabilities, it is necessary to evaluate their capabilities. To this end, the evaluation indicator system is established by using the three-dimensional indicator system construction model of "maintenance task → task demand → capability demand", and the evaluation method based on intuitionistic fuzzy entropy and normal grey cloud model is proposed, using intuitionistic fuzzy entropy theory to determine the expert weights and indicator weights, and the grey cloud model theory to determine the capability evaluation level. Finally, the application process of the evaluation model is demonstrated through specific examples, and the evaluation results are analyzed to verify the effectiveness of the evaluation model.

Modern war is sudden and rapid, and once the battle starts, the demand for equipment maintenance and guarantee will show an outburst situation, which puts equipment maintenance and guarantee capability to a severe test. To accurately grasp the civil-military integration of aviation maintenance and guarantee capabilities, it is necessary to evaluate their capabilities. To this end, the evaluation indicator system is established by using the three-dimensional indicator system construction model of "maintenance task → task demand → capability demand", and the evaluation method based on intuitionistic fuzzy entropy and normal grey cloud model is proposed, using intuitionistic fuzzy entropy theory to determine the expert weights and indicator weights, and the grey cloud model theory to determine the capability evaluation level. Finally, the application process of the evaluation model is demonstrated through specific examples, and the evaluation results are analyzed to verify the effectiveness of the evaluation model.

Abstract: Steamed ginseng water (SGW), the by-product generated from the heated processing of red ginseng, with high content of active substances, better skincare activities, and large amount output ineffective utilization, resulted in environmental pollution and resource waste. In current study, UHPLC-Q-Exactive-MS/MS liquid chromatography-mass spectrometry and multivariate statistical analysis were conducted to characterize the compositional features of the repeated thermal-treated SGW. The total sugar content, total sugar content, total reducing sugar content, total non-reducing sugar content, DPPH, ABTS+, Fe3+ reducing capacity, and the hydroxyl radical scavenging abilities were employed to evaluate the gross contents variation connect with anti-oxidant activities during heat processes. The result revealed the SGW content and antioxidant activity were highly correlated, the 7th SGW sample showed the highest content and the strongest ability on anti-aging capacities. 38 significant common differential markers were screened, by the four compared SGW groups (1- and 3-, 1- and 5-, 1- and 7-, and 1- and 9) through OPLS-DA analysis. The current study showed that the thermal proceeding times could be a vital index value during the recycling operation quality control of SGW, which has a huge potential in anti-aging cosmetic raw materials, In the meanwhile, our results provided a green, sustainable, low-cost thinking of rational application on ginseng resource.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

MEMS (Micro-electromechanical Systems) becomes important increasingly due to the smarter and smaller fuze used in OICW (Objective Individual Combat Weapon). MEMS Safety and Arming (S&A) device is employed in different platforms and regions for small caliber projectile. Therefore, it is necessary to make a parametric study of the MEMS S&A device in different apply environments and explore the main sensitive factors of the MEMS S&A device to provide reference for designs. In this paper, based on the MEMS S&A device designed by our term, theory and finite element models are established, and the centrifugal insurance mechanism of the MEMS S&A device is parametric studied under the different speeds, temperature and thickness of the model by nonlinear dynamic method. By comparing the experimental and predicted results, the established FEM model is verified, and the conclusion is that the temperature and the centrifugal force are the main sensitive factors in the centrifugal insurance mechanism. In summary, we can suggest that the application environment, which the MEMS S&A device is suitable for, is the temperature equal to or slightly greater than normal temperature and the rotating speed higher than35000r/min of small caliber projectile.

Territory space is an ecological resource carrier and place for human development. Human activities and ecological systems are the basis of ecological product supply. Promoting territory spatial protection and governance by improving the ecological products supply is very important. In this study, we established an ecological products supply capacity evaluation index system involving three types of ecological products, i.e., ecological environmental products, ecological material products, and ecological cultural products. For the case of the Beijing-Tianjin-Hebei region, we comprehensively used principal component analysis, equivalent factor method, and entropy method to evaluate the supply capacity of the ecological products from 2011 to 2021. Then, we analyzed the spatio-temporal pattern combining the natural breakpoint and quantile classification methods and analyzed the obstacle factors using the obstacle degree model of ecological supply. The results show that the supply capacity of different ecological product in each city are closely related to ecological resource endowment. The supply capacity of ecological products exhibited an upward trend, with the highest ecological environmental products supply, relatively smaller ecological material product supply, and the largest growth rate for ecological cultural product supply. The supply capacity of different ecological products varied across cities over time and displayed noticeable spatial differentiation. The main obstacle factors included eco-land, eco-tourism, eco-leisure, park green space, and fishery products, although there were variations among cities. Finally, based on the level, spatial-temporal pattern, and obstacle factors of ecological product supply, we proposed strategies for territory spatial protection and governance from the perspectives of integrated protection of elements, structural regulation, and systematic governance. The results reflected the ecological functional heterogeneity of territory space, which can provide spatial planning guidance for sustainable development.

Mitochondrial alternative oxidase 1a (AOX1a) plays an extremely important role in critical node of seed viability. However, the regulatory mechanism is still poorly understood. The study aims to identify regulatory mechanisms by comparing between OsAOX1a-RNAi and wild type (WT) rice seed during artificial aging treatment. Gain weight and P50 significantly decreased in OsAOX1a-RNAi rice seed, indicating that there might be impaired in seed development and storability. Compared to WT seeds in the 100%, 90%, 80%, and 70% germination, respectively, NADH and succinate-dependent O2 consumption, the activity mitochondrial malate dehydro-genase and ATP contents were decreased in OsAOX1a-RNAi seeds in the 100%, 90%, 80%, and 70% germination, respectively, indicating that mitochondrial status in the OsAOX1a-RNAi seeds after imbibition was weaken than the WT. In addition to, the reduced abundance of complex I N and P module subunits might showed that the capacity of mitochondrial electron transfer chain was significantly inhibited in the OsAOX1a-RNAi seed at critical node of seed viability. Above results might indicated that the ATP production was impaired in OsAOX1a-RNAi seeds during ageing. Therefore, we conclude that the activities of mitochondrial metabolism and alternative pathways were severely inhibited in OsAOX1a-RNAi seeds at critical node of viability, which was leading to accelerate the collapse of seed viability. The precise regulatory mechanism of the alternative pathway at the critical node of viability still needs to be further analyzed.

Salvia hispanica (chia) is a highly nutritious food source and has gained popularity due to its high omega-3 fatty acid content. Red spider mites are a serious problem in the production of S. hispanica. However, no study has been conducted to analyse the defensive response to the infestation of red spider mites in S. hispanica. To elucidate the molecular mechanisms of the defensive response of S. hispanica to red spider mites, we performed a transcriptomic analysis of S. hispanica when infested by red spider mites. In the comparative assessment of leaf transcriptomes, a total of 1743 differentially expressed genes (DEGs) were identified between control and mite-infested S. hispanica. From these, 1208 (69%) transcripts were up-regulated and 535 (31%) were down-regulated. The DEGs included transcription factors, defense hormones, and secondary metabolites that were either suppressed or activated in response to spider mite herbivory. Gene Ontology (GO) enrichment analysis revealed that plant secondary metabolites such as glucosinolates, and signalling pathways, including the jasmonic acid signalling pathway, may play an important role in the defence against red spider mites. This study provides novel insights into the defence response of S. hispanica in response to insect herbivory and could be a resource for the improvement of pest resistance in the chia.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

Version Control and Source Code Management Systems, such as GitHub, contain large amount ofunstructured historical information of software projects. Recent studies have introduced Natural Language Processing (NLP) to help software engineers retrieve information from very large collection of unstructured data. In this study, we have extended our previous study by increasing our datasets and ML and clustering techniques. Method: We have followed a complex methodology made up of various steps. Starting from the raw commit messages we have employed NLP techniques to build a structured database. We have extracted their main features and used as input of different clustering algorithms. Once labelled each entry, we have applied supervised machine learning techniques to build a prediction and classification model. Results: We have developed a machine learning-based model to automatically classify commit messages of a software project. Our model exploits a ground-truth dataset which includes commit messages obtained from various GitHub projects belonging to the HEP context. Conclusions: The contribution of this paper is two-fold: it proposes a ground-truth database; it provides a machine learning prediction model. They automatically identify the more change-proneness areas of code. Our model has obtained a very high average precision, recall and F1-score.

Service pricing is a bottleneck in the development of innovation services, as it is the issue of most concern between the suppliers and demanders. In this paper, a negotiation pricing model that is based on the multiobjective genetic algorithm is developed for innovation service pricing. Regarding the service pricing process as a multiobjective problem, the objective functions, which include the service price, service efficiency, and service quality, for suppliers and demanders are constructed. As the solution of a multiobjective problem is typically a series of alternatives, another negotiation process is necessary for determining the final decision. A learning strategy is adopted during the negotiation process to simulate reality. Finally, the model is implemented for an innovation service transaction, the objective of which is to identify the optimal price plan. The results demonstrate that the model can provide quantitative decision support for the pricing of an innovation service and ultimately yield a win-win result for both the supplier and demander of the innovation service. Furthermore, the influence of the parameters during the negotiation process is analyzed in detail. The effects of the learning strategy on accelerating the negotiation process, as well as the chosen of reasonable parameters are given.

The rapid development of 2019-2020 Wuhan seafood market pneumonia currently posed a major public health concern in China. Genome sequencing identified a novel beta-coronavirus closely related to SARS-CoV, named 2019-nCoV by WHO, as the cause of this pandemic disease. Viruses with single stranded RNA genome are prone to evolve quickly by accumulation of mutations, such as SNV, INDEL and cross viral recombination, aiding fast transmission among hosts and cross species. Here we collected related genome sequences and investigated variations shared by different strains of 2019-nCoV, identified reoccurrence of SNV mutations in clusters of patients, an indication of rapid evolution of 2019-nCoV at the transmission from animal host to human. The information collected herein would help to understand the dynamics of current pandemic.

Thought runs through the mind like blood runs through our body to keep us alive. Like the mind, the body does not stay inert and is in constant motion. Not a single cell in our body is left inert unless cell is under stress or dying. These scenarios are reflected upon when a person is sick, the person lies in bed with less movement; however, is active when the person is healthy. The topic of mechanical stimulation has emerged due to the increasing understanding of the physical stimulations we face each day. Further understanding of the mechanically-regulated mechanism can help us explore the pathological events in a disease. Here, we reviewed the role of sensory proteins in pathological events that are observed in cardiomyopathy, cancer, respiratory, renal, obesity, genetics, physical injury and bacterial infection. Taken together, sensory proteins are mechanically-activated which assist reception of external physical stimulation and convert into biochemical to trigger intracellular signaling cascade.

The intestinal microbial community of aquatic animals is closely related to the environment and thus affects the health of aquatic animals. Here we investigated annual variation of intestinal bacteria community structures of Ruditapes philippinarum cultured using two different methods, bottom sown and raft hanging. Bacterial diversity of seawater and sediment in different seasons was examined as well. Correlation between R. philippinarum intestinal bacteria community structures and environmental factors was analyzed. The results showed that in the two aquculture areas where R. philippinarum was differentially cultured, bacteria community structure of seawater and sediment both altered with seasons. However, neither seasonal changes nor difference in culture methods could significantly affect the intestinal bacteria community structures of R. philippinarum. Additionally, in terms of the alpha diversity of intestinal bacteria communities, there was no significant difference in R. philippinarum cultured using the two methods. For benthic cultured clams, alpha diversity of the intestinal bacterial communities was often higher than that of the environmental bacterial communities. For raft hanging cultured calms, Alpha diversity of the intestinal bacterial communities was normally comparable with that of the environmental counterparts. Beta diversity analysis showed that the intestinal bacterial community structure of R. philippinarum was mainly determined by both deterministic and stochastic processes. Correlation analysis showed that the intestinal bacterial community structures of R. philippinarum were determined by a variety of environmental factors. For clams collected from the benthic culture area, the intestinal bacterial structure was more correlated with the physicochemical properties of sediment in comparing with those of seawater. For clams collected from the raft-culture area, the intestinal bacterial structure was mainly determined by the phsicochemical characteristics of seawater. This study helps us to better understand the bacterial community structure in complex aquaculture ecosystems, providing a reference for healthy shellfish aquaculture and ecosystem protection in aquaculture area.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

The scope of this work was part of our previous research on Pulsed Power Plasma Stimulation Technique. Electromagnetic fields generated during a pulsed power plasma discharge were simulated using a finite element method in the COMSOL RF module. The field distributions were calculated during and after the pulse. The current paper takes advantage of prior work measuring and modeling the current distribution in the plasma arc. Agreement with laboratory experimental measurements provides support for extension of the model to reservoir scale. The validated model was used to quantify the signal attenuation level in different medium environment.

Euler sums are alternating (or level two) extension of multiple zeta values (MZVs). Kaneko and Tsumura initiated the study of multiple T-values (MTVs), another level two generalization, by restricting the summation indices in the definition of MZVs to a fixed parity pattern. In this paper, we shall study finite MTVs and their alternating versions which are level two and level four variations of finite MZVs, respectively. We conjecture that all finite MZVs are in the Q-span of finite MTVs which in turn apparently lie in the span of finite Euler sums, and the inclusions are both proper. We shall first provide some structural results for Euler sums of small weights, guided by the author's previous conjecture that the finite Euler sum space of weight w is isomorphic to a quotient Euler sum space of weight w. Then, by utilizing some well-known properties of the classical alternating MTVs, we shall derive a few important Q-linear relations among the finite alternating MTVs, including the reversal, linear shuffle and sum relations. We then compute the upper bound for the dimension of the Q-span of weight w finite (alternating) MTVs for w<9, both rigorously using the newly discovered relations and numerically aided by computers.

Despite the strong anticancer activity of SN38 (7-ethyl-10-hydroxy-camptothecin), some defects prevent its clinical application, such as severe side effects and loss of anticancer activity due to lack of selectivity to cancer cells and hydrolysis of ring E, respectively. To address the issue, herein a multifunctional SN38 derivative (compound 9) containing biotin (tumor-targeting group) and valproic acid (histone deacetylase inhibitor, HDACi) was synthesized via click chemistry and evaluated using MTT assay. The in vitro cytotoxicity study showed that compound 9 exhibited superior cytotoxicity as irinotecan against human cervical cancer HeLa cells, albeit inferior to SN38. More significantly, compound 9 significantly reduced toxicity in mouse embryonic fibroblast NIH3T3 cells, indicating that compound 9 had the capacity to enhance tumor targeting due to its cell selectivity. Further studies demonstrated that compared with irinotecan, compound 9 induced similar apoptosis of cancer cells. Consequently, compound 9 can not only improve its tumor-targeting ability mediated by biotin but also exert the potent anticancer activity through the synergism of SN38 and valproic acid, indicating that the design concept is an effective strategy for structural modification of SN38.

In the fifth generation communication system, millimeter wave (mmWave) networks will coexist with traditional micro wave (μWave) networks, which allows for higher data transmission rate and better user experience. In this paper, we give a comprehensive framework of mathematical models and analytical methods for multi-tier mmWave and μWave hybrid caching networks based on stochastic geometry. We propose an association strategy by assuming average biased-received power association and Rayleigh fading. Accordingly, by using a D-ball approximating blockage model of mmWave networks, expressions of the cell association probability and the coverage probability of the hybrid networks are derived. Also, we use the average successful delivery probability as the performance metric to analyze the existing caching placement strategies. Simulation results validate the accuracy of our analytical conclusions.

Purpose- This study seeks to investigate the collaboration between Digitalization and traditional manufacturing industry and investigate, how digitalized management brings new chances and challenges of management. Design/methodology/approach – The author designed a content analytical study researching the role of digitalization in traditional manufacturing industries. The article presents a selective but systematical review of recent digitalization trend and digital twin to be applied for innovative management in Industry 4.0 era. Findings– Digitalization is highly correlated with traditional manufactory in Industry 4.0 era. The study brings a new outlook on the next wave of Digitalization and review of associated challenges and opportunities for management and innovation in traditional manufacturing industries. Research limitations/implications – The research focuses on two branches of traditional industries only: machine tools building and metalworking industries. Future research needs to examine other traditional industries. The research is limited to 2 high related traditional manufacturing industries, machine tools and metalworking industry. Practical implications – The study and application of digitalization should be highly recommended and launched in traditional manufacturing industries. Universities, institutes and vocational schools should update, optimize their courses systems according to prediction of future industry. Originality/value – The paper enhances understanding about the collaboration between digitalization and traditional manufacturing industry. This paper analyzes an important issue the digitalization serves traditional industries. It is unique in its broad analysis of the related terms – Digitalization, Machines 4.0, Industry 4.0 and innovative management in Industry 4.0 era.

Aspergillus montevidensis is an important domesticated fungus that has been applied to produce many traditional fermented foods under high osmotic conditions. However, the detailed mechanisms of tolerance to osmotic stress remain largely unknown. Here, we construct a target-deleted strain (ΔLeuRS) of A. montevidensis and found that the ΔLeuRS mutants grew slowly and suppressed the development of the cleistothecium compared to the wide-type strains (WT) under salt-stressed conditions. Furthermore, differentially expressed genes (P<0.0001) governed by LeuRS were involved in salt tolerance, ABC transporter, amino acid metabolism, sugar metabolism, and reproduction process. The ΔLeuRS strains compared to WT strains under short- and long-term salinity stress especially altered accumulation levels of metabolites, such as amino acids and derivatives, carbohydrates, organic acids, and fatty acids. The study provides new insights into the underlying mechanisms of salinity tolerance and lays a foundation for favor improvement of foods fermented with A. montevidensis.

Molecular communication (MC) is a promising bio-inspired paradigm for exchanging molecule information among nanomachines. This paper proposes a synchronisation-assist photolysis MC system that aims to transmit the bio-sensing signal of the tumour microenvironment, facilitated by mitigating redundant molecules for improved bit error rate (BER) performance. Benefits from bio-compatible MC, biosensors could transmit bio-sensing signals of the tumour in $vivo$ instead of converting them to electrical signals. Due to diffusion motion's slow and stochastic nature, inter-symbol interference (ISI), resulting from previous symbols' residual information molecules, inevitably occurs in diffusion-based MC. ISI is one of the challenges in diffusion-based MC, which significantly impacts signal detection. Inspired by on-off keying (OOK) modulation, the proposed modulation implements a switch of molecules and light alternatively. The light emitted is triggered by a synchronisation signal, and the photolysis reactions could reduce the redundant molecules. An expression for the relevant channel impulse response (CIR) is derived from a hybrid channel model of diffusion and photolysis-reaction. This paper implements the maximum posterior estimation scheme to find the optimal decision threshold and analysis the BER performance in terms of different time intervals of the system. Numerical simulations demonstrate that the proposed method can improve the channel capacity and BER performance. We believe that our work may pave the way for MC application in bio-sensing.

Green and low-carbon development has become an important embodiment of China's path to becoming a strong agricultural country. How to enable agricultural enterprises to better adopt green technologies and conduct production and operation with the concept of sustainable development has become a key link. This article utilizes a structural equation model (SEM) to analyze the role paths and mediating effects of organizational learning ability and policy orientation in agricultural enterprises' market orientation and willingness to adopt green technologies[ The definition of green technology in this paper refers to Guo Kesha, Tian Xiaoxiao. Green technology and green transformation of industrial development mode [J]. Tianjin Social Sciences, 2024 (02) :99-107, including green manufacturing (production) technology and green service technology.]. The results show that market orientation, organizational learning ability, and policy effectiveness have significant direct positive impacts on the willingness to adopt; market orientation has a significant positive impact on agricultural enterprises' organizational learning ability, organizational learning ability has a significant positive impact on policy orientation, and market orientation has a significant positive impact on policy effectiveness; the results of mediation analysis also indicate that learning ability has a significant mediating effect between market orientation and willingness to adopt, and policy effectiveness has a significant mediating effect between market orientation and willingness to adopt. Through difference analysis, it is believed that the mediating effects of the three paths are equally important, and organizational learning ability and policy effectiveness play a partial mediating role in agricultural enterprises' willingness to adopt green technologies. Based on this, policy suggestions are proposed to improve enterprises' own organizational learning ability, increase the promotion of policies related to green technologies, improve relevant policies for the application of green technologies, and increase research and development efforts for green technologies.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

This paper studies the mechanism of how China’s state-owned enterprise (SOEs) reform can influences economic growth, and distinguishes the capital efficiency between state-owned and private enterprises. The results show that: 1) the capital allocation efficiency among state-owned enterprises is lower than private enterprise due to an insufficiently released productivity of state-owned enterprises; 2) although with a higher capital allocation efficiency, the improvement of technology progress of private enterprises at a much slower pace compared to its rapidly increasing share in China’s economy. In case of poor allocation with private sector, blindly reforming ownership of state-owned enterprises cannot effectively alleviate the problem of efficiency losses. State-owned enterprise reform can boost economic growth by increasing capital marginal output, improving capital dynamic allocation efficiency, promoting TFP growth and exerting external spillovers on other firms. At present, China is exploring the endogenous power of economic growth, improving the market institutions and promoting the state-owned enterprises reform with positive and steady pace. By properly re-allocation SOEs into the private sector, which has significant influence on improving economic efficiency and promoting sustained economic growth.

The existing segmentation-based scene text detection methods mostly need complicated post-processing, and the post-processing operation is separated from the training process, which greatly reduces the detection performance. The previous method, DBNet successfully simplified post-processing and integrated the post-processing into a segmentation network. However, the training process of the model took a long time for 1200 epochs and the sensitivity to texts of various scales was lacking, leading to some text instances being missed. Considering the above two problems, we design the text detection Network with Binarization of Hyperbolic Tangent(HTBNet). First of all, we propose Binarization of Hyperbolic Tangent (HTB), optimized along with which, the segmentation network can expedite the initial convergent speed by reducing the amount of epochs from 1200 to 600. Because features of different channels in the same scale feature map focus on the information of different regions in the image, to better represent the important features of all objects in the image, we devise the Multi-Scale Channel Attention(MSCA). Meanwhile considering that multi-scale objects in the image cannot be simultaneously detected, we propose a novel module named Fused Module with Channel and Spatial(FMCS), which can fuse the multi-scale feature maps from channel and spatial dimension. Finally we adopt cross entropy as the loss function, which measures the difference between predicted values and ground truths. The experimental results show that HTBNet compared with lightweight models has achieved competitive performance and speed on Total-Text(F-measure:86.0%, FPS:30) and MSRA-TD500 (F-measure:87.5%, FPS:30).

Electricity consumption is often the hotspot of life cycle assessment (LCA) of products, industrial activities, or services. The objective of this paper is to provide a consistent, scientific, region-specific electricity-supply-based inventory of electricity generation technology for national and regional power grids. Marginal electricity generation technology is pivotal in assessing impacts related to additional consumption of electricity. China covers a large geographical area with regional supply grids; these are arguably equally or less integrated. Meanwhile, it is also a country with internal imbalances in regional energy supply and demand. Therefore, we suggest an approach to achieve a geographical subdivision of the Chinese electricity grid, corresponding to the interprovincial regional power grids, namely the North, the Northeast, the East, the Central, the Northwest, and the Southwest China Grids, and the China Southern Power Grid. The approach combines information from the Chinese national plans on for capacity changes in both production and distribution grids, and knowledge of resource availability. The results show that nationally, marginal technology is coal-fired electricity generation, which is the same scenario in the North and Northwest China Grid. In the Northeast, East, and Central China Grid, nuclear power gradually replaces coal-fired electricity and becomes the marginal technology. In the Southwest China Grid and the China Southern Power Grid, the marginal electricity is hydropower towards 2030.

Tea (Camellia sinenesis) is a health beneficial beverage and is also a source for extracting bioactive components such as theanine, tea polyphenols (TPP) and tea polysaccharides (TPS). TPS is a group of hetero-polysaccharides bounded with proteins. There were tests showing that TPS had various bioactivities, such as antioxidant, antitumors, antihyperglycemia, anti-inflammation and improving immunity. However, inconsistent results concerning chemical composition and bioactivity of TPS were published in recent years. The advances in chemical composition and bioactivities of TPS were reviewed in the present paper. The inconsistent and controversial results regarding composition and bioactivities of TPS were also discussed.

An innovative superconducting mechanism was developed based on a patented discovery of room temperature superconductivity in several thorium (Th) salts or compounds. The rationale behind this discovery is through the experimental results about the unique electrical and magnetic properties of these Th salts. Accordingly, this new superconducting mechanism for these Th salts was obtained through the analyses of the compounds’ molecular configurations and the packings of their relevant crystal structures. Owing to the distinctive properties of the Th compounds in this discovery, we further established a different electron pairing scheme as opposed to the pairing of the Cooper pairs. Compared to the long distance electron pairing of the Cooper pairs, the new electron pairing in our mechanism is constructed by two closely correlated electrons that reside on the same atomic orbital of the Th cation as an electron lone pair. In this new superconducting mechanism, the Th cation is sitting on a relevant crystallographic lattice arrangement or a network of the relevant Th compounds. This network is constructed by many Th cations along certain crystallographic lattice arrangement where each Th cation contains one electron lone pair. This network allows the electron lone pairs on the Th cations to be delocalized over the network, “in pair”, and thus, reveals the electron lone pair in presence in a long distance fashion. The closely correlated electron lone pairs hop on this network and thus, construct the supercurrent over the network. This explanation about the superconductivity laid the basis for our superconducting mechanism. All these conclusions came from the previous studies about these compounds that illustrated their unusual features of a coexistence of high electrical conductivity and diamagnetism. These electrical and magnetic properties fall in line with that of superconductors but, surprisingly, these Th compounds have such properties at the ambient condition, meaning under room temperature and atmosphere pressure. We expect that this mechanism may be appropriate to be utilized to other superconducting cases, either conventional or unconventional, and therefore, can be adapted to describe the superconducting phenomenon for other superconductors.

A one-pot, one-step protocol combining hydrogen transfer initiated dehydration (HTID) of 1,3-propanediol (1,3-PDO), catalysed by [Cp*IrCl2(NHC)] (Cp* = pentamethylcyclopentadienyl; NHC = carbene ligand) complexes (1-5H and 1-3F), and self-aldol condensation (SAC) of propanal (2), allowed selective production of aldehyde 2-methyl-pent-2-enal (3), in ionic liquids with high substrate conversion. The Ir(III) pre-catalysts, and the ionic liquids, were recyclable. 3 could also be selectively produced in the presence of water, and in neat 1,3-PDO. The efficient, selective delivery of a value-added chemical from 1,3-PDO, a major product of many whole cell bacterial fermentation processes, shows that the combination of chemo-catalytic processing of the chemical platform via Cp*IrCl2(NHC) - catalysed HTID / SAC with bio-catalysis has the potential to allow direct valorisation of the bio-renewable feedstocks, such as waste glycerol and sugars, into valuable chemicals.