The adsorption of supramolecular composites for Cs(I) in high level liquid waste (HLLW) are different due to different carriers. We chose 25,27-bis(ethyl)-calix[4]arene-26,28-crown-6 (EC[4]C6) as adsorbent, SiO2-P, XAD-7 and UiO-66 as carriers. The synthesis and characterization of supramolecular EC[4]C6 loaded with three different carriers were presented. SEM, N2 adsorption/desorption isotherms, TG-DSC spectra, FT-IR spectra results shown that EC[4]C6 was successfully introduced into the pores of carriers via physical intermolecular interactions. EC[4]C6/SiO2-P, EC[4]C6/XAD-7 and EC[4]C6/UiO-66 shown high efficiency, high selectivity towards Cs(I) over 18 typical fission or corrosion products in HNO3 solution. The adsorption properties of the three materials were investigated after electron irradiation. These results demonstrate that EC[4]C6/SiO2-P possess greater potential for highly efficient removal of Cs(I) from HLLW.

Environmentally friendly lead-free K1-xNaxNbO3 (KNN) ceramics possess electromechanical properties comparable to lead-based ferroelectric materials, but cannot meet the needs of device miniaturization, and the corresponding thin films lack of theoretical and experimental studies. To this end, we developed the nonlinear phenomenological theory for ferroelectric materials to study the effects of non-equiaxed misfit strain on the phase structure, electromechanical properties and electrical response of K0.5Na0.5NbO3 epitaxial films and constructed the in-plane misfit strain (u1-u2) phase diagrams. The results show that K0.5Na0.5NbO3 epitaxial film under non-equiaxed in-plane strain can exhibit abundant phase structures, including orthorhombic a1c, a2c and a1a2 phases, tetragonal a1, a2 and c phases, and monoclinic r12 phases. Moreover, in the vicinity of a2c-r12, a1c-c and a1a2-a2 phase boundaries, K0.5Na0.5NbO3 epitaxial films exhibit excellent dielectric constant ε11, while at a2c -r12 and a1c-c phase boundaries large piezoelectric coefficient d15 is observed. It was also found that high permittivity ε33 and piezoelectric coefficients d33 exist near the a2c - a2, r12- a1a2 and a1c-a1 phase boundaries due to the existence of polymorphic phase boundaries (PPB) in the KNN system, which makes it easy to polarize near the phase boundaries, and the polarizability changes suddenly, leading to electromechanical enhancement. In addition, the results show that the K0.5Na0.5NbO3 thin films possess a large electrocaloric response at the phase boundary at the r12-a1a2 and a1c-a1 phase boundaries. And the maximum adiabatic temperature change ∆T is about 3.62 K when the electric field change is 30 MV/m at room temperature, which is significantly enhanced compared with equiaxed strain. This study provides theoretical guidance for obtaining K1-xNaxNbO3 epitaxial thin films with excellent properties.

Adipose-derived stem cells (ADSCs) were suggested for treating degenerative osteoarthritis, suppressing inflammatory responses, and repairing damaged soft tissues. Moreover, the ADSCs have the potential to undergo self-renewal and differentiate into bone, tendon, cartilage, and ligament. Recently, investigation of the self-renewal and differentiation of the ADSCs becomes an attractive area. In this work, a pneumatic microdevice has been developed to study the gene expression of the ADSCs after the stimulation of multi-axial tensile strain. The ADSCs were cultured on the microdevice and experienced multi-axial tensile strain during a 3-day culture course. Self-renewal and differentiation abilities were investigated by mRNA expressions of NANOG, SOX2, OCT4, SOX9, PPAR-γ, and RUNX2. The result showed that the genes related self-renewal were significantly up-regulated after the tensile stimulation. Higher proliferation ratio of the ADSCs was also shown by cell viability assay. The microdevice provides a promising platform for cell-based study under mechanical tensile stimulation.

In GNSS/IMU integrated navigation systems, factors such as satellite occlusion and non-line-of-sight conditions can lead to degradation of satellite positioning results, Subsequently affecting the overall accuracy of the integrated navigation system. To address this issue and ef-fectively utilize historical pseudorange information from satellites, this paper proposes a graph optimization-based GNSS/IMU model with virtual constraints. These virtual constraints are con-structed using satellite ‘s position from previous time step, the rate of change of pseudoranges, and ephemeris data. This virtual constraint can serve as an alternative solution for individual satellites in case of signal anomalies, ensuring the integrity and continuity of the graph optimi-zation model. Additionally, this paper conducts an analysis of the graph optimization model constructed using these virtual constraints, comparing it with traditional integrated navigation graph optimization model, and analyzes and reconstructs the marginalization process based on these virtual constraints. The experimental results, compared with tightly coupled Kalman fil-tering and the original graph optimization method on a set of real-world data, demonstrate that the introduction of virtual pseudoranges maintains high positioning accuracy. The RMSE error between it and the original graph optimization remains within 5%, affirming the high feasibility of this approach.

Methylsilsesquioxane aerogels with uniform mesopores have been facilely prepared via a sol–gel process followed by microwave drying with methyltrimethoxysilane (MTMS) as precursor, hydrochloric acid (HCl) as catalyst, water and methanol as solvents, hexadecyltrimethylammonium chloride (CTAC) as surfactant and template and propylene oxide (PO) as gelation agent. The microstructure, chemical composition and pore structures of the resultant MSQ aerogels were investigated in detail to achieve controllable preparation of MSQ aerogels, and the thermal stability of MSQ aerogels was also analyzed. The gelation agent, catalyst, solvent and microwave power have important roles on pore structures of MSQ aerogels. Meanwhile, microwave drying method is found to not only have a remarkable effect on improving production efficiency, but also be conducive to avoid the collapse of pore structure especially micropores during drying. The resulting MSQ aerogel microwave-dried at 500 W possesses a specific surface area up to 821 m2/g and a mesopore size of 20 nm, and displays good thermal stability.

To prevent CO2 leakage and ensure the safety of long-term CO2 storage, it is essential to investigate the flow mechanism of CO2 in complex pore structures at the pore scale. This study focuses on reviewing the experimental, theoretical, and numerical simulation studies on the microscopic flow of CO2 in complex pore structures during the last decade. For example, advanced imaging techniques, such as X-ray computed tomography (CT) and nuclear magnetic resonance (NMR), are used to reconstruct the complex pore structures of rocks. Mathematical methods, such as Darcy's law, Young–Laplace’s law, and the Navier-Stokes equation, are used to describe the microscopic flow of CO2. Numerical methods, such as the lattice Boltzmann method (LBM) and pore network (PN) model, are used for numerical simulation. The application of these experimental and theoretical models and numerical simulation studies is discussed, considering the effect of complex pore structures. Finally, future research is suggested to focus on: (1) Conducting real-time CT scanning experiments of CO2 displacement combined with the developed real-time CT scanning clamping device to realize real-time visualization and provide quantitative description of the flow behavior of CO2 in complex pore structures; (2) The effect of pore structures change on the CO2 flow mechanism caused by the chemical reaction between CO2 and the pore surface, the flow theory of CO2 considering wettability and damage theory in a complex pore structures; (3) The flow mechanism of multi-phase CO2 in complex pore structures; (4) The flow mechanism of CO2 in the pore structures at multiscale and the scale upgrade from microscopic to mesoscopic to macroscopic. Generally, this study focuses on reviewing the research progress of CO2 flow mechanisms in complex pore structures at the pore scale and affords an overview of potential advanced developments to enhance the current understanding of CO2 microscopic flow mechanisms.

Time-modulated sparse circular array (TMSCA) with elements uniformly excited is designed and synthesized in this paper. By utilizing rotationally symmetric structure, the array geometry and the time modulation of the TMSCA is presented, and the radiation patterns in frequency domain are formulated. In order to achieve the desired radiation pattern at the operating frequency and suppress the sideband radiation, the synthesis problem is established and solved by the proposed harmony search-convex programming (HS-CP) algorithm in two dependent optimizations. Two designs are presented, and the numerical results indicate that the TMSCA with rotationally symmetric structure has the advantages of designing time-modulated sparse arrays with superior performance.

In this paper, the sol−gel method was used to synthesize powders of LaMnO3 (LMO), La0.85Ca0.15MnO3 (LCM), and La0.85Sr0.15MnO3 (LSM). We investigated the impact of substituting Ca and Sr at the A−site on the perovskite crystal structure and electrochemical capabilities of LMO. LCM retained its orthogonal structure in comparison to the parent LMO components, whereas LSM transitioned to a rhombic structure. At 0.5 A/g, the specific capacitance of LCM and LSM electrodes is 185.5 F/g and 248 F/g, respectively.The specific capacitance of LCM was more three times than that of the LMO electrode. Among the three samples (LMO, 22.25 m2 g−1; LSM, 31.56 m2 g−1), the LCM sample exhibited the highest specific surface area of 38.79 m2 g−1. The charge transfer resistances of the LMO, LCM, and LSM are 0.48 Ω, 0.36 Ω, and 0.38 Ω, correspondingly. The LCM electrode exhibits the greatest capacitance performance due to its more refined morphology, increased concentration of oxygen vacancy, and more complete utilization of the perovskite bulk structure. The above results demonstrate that Ca or Sr substitution of A−site compounds has great potential for supercapacitor applications.

The genetic code evolved around the reading of the tRNA anticodon on the primitive ribosome, and tRNA-34 wobble and tRNA-37 modifications coevolved with the code. We posit that EF-Tu, the closing mechanism of the 30S ribosomal subunit, methylation of wobble U34 at the 5-carbon and suppression of wobbling at the tRNA-36 position were partly redundant and overlapping functions that coevolved to establish the code. The genetic code devolved in evolution of mitochondria to reduce the size of the tRNAome (all of the tRNAs of an organism or organelle). “Superwobbling” or four-way wobbling describes a major mechanism for shrinking the mitochondrial tRNAome. In superwobbling, unmodified wobble tRNA-U34 can recognize all four codon wobble bases (A, G, C and U), allowing a single unmodified tRNA-U34 to read a 4-codon box. During code evolution, to suppress superwobbling in 2-codon sectors, U34 modification by methylation at the 5-carbon position appears essential. As expected, at the base of code evolution, tRNA-37 modifications mostly related to the identity of the adjacent tRNA-36 base. TRNA-37 modifications help maintain the translation frame during elongation.

Thymic stromal lymphopoietin (TSLP) is a cytokine and is closely related to Interleukin (IL) - 7, and hTSLP can activation through the human thymus dendritic cell in thymic to indirectly promote the differentiation of natural Regulatory T cells (Tregs) of the thymus. In this study, we focused on recombinant TSLP to determine its effects on the differentiation of CD4+CD25-T cells separated from the thymus of myasthenia gravis (MG) patients. Our results demonstrated that exogenous TSLP could increase CD4+CD25+T/CD4+T cells ratio, up-regulate the expression of Foxp3 mRNA and protein expression in CD4+CD25+Treg cells. Furthermore, we found that CD4+CD25+ Treg cells induced by exogenous TSLP could secrete IL - 10, Transforming growth factor (TGF) - β and the ability to inhibit CD4+T cell proliferation improved. These results indicate that TSLP may promote the differentiation of thymic CD4+CD25-T cells of MG patient to CD4+CD25+Foxp3+ regulatory T cells and enhance the function of immune suppression.

The genetic code evolved by parallel tracks of chaotic and ordered processes. Liquid-liquid phase separation (hydrogels), a chaotic process, constructs diverse membraneless compartments within cells, resulting in regulated hydration and sequestration and concentration of reaction components. Hydrogels relate to chaotic amyloid fiber production. We propose that polyglycine and related hydrogels (i.e. GADV; G is glycine), phase separations, membraneless droplets and amyloid accretions organized protocell domains to drive the earliest evolution of the genetic code and the pre-life to cellular life transition. By contrast, evolution of tRNA, tRNAomes, aminoacyl-tRNA synthetases and translation systems followed highly ordered and systematic pathways, described by well-defined mechanisms and rules. The pathway of evolution of aminoacyl-tRNA synthetases, which tracked evolution of the genetic code, is clarified. Hydrogels and amyloids form a chaotic component, therefore, that complemented otherwise systematic processes. We describe with detail a pre-life world in which hydrogels and amyloids provided the selections of the first life.

There are no theorems (proven theories) in the biological sciences. We propose that the 3 31 nt minihelix tRNA evolution theorem be universally accepted as one. The 3 31 nt minihelix theorem completely describes evolution of type I and type II tRNAs from ordered precursors (RNA repeats and inverted repeats). Despite diversification of tRNAome sequences, statistical tests overwhelmingly support the theorem. Furthermore, the theorem relates the dominant pathway for the origin of life on Earth, specifically, how tRNAomes and the genetic code may have coevolved. Alternate models for tRNA evolution (i.e., 2 minihelix, convergent and accretion models) are falsified. In the context of the pre-life world, tRNA was a molecule that via mutation could modify anticodon sequences and teach itself to code. We relate the clearest history to date of the chemical evolution of life on Earth. From analysis of tRNA evolution, ribozyme-mediated RNA ligation was a primary driving force in evolution of complexity during the pre-life to life transition on Earth.

The 3 31 nucleotide minihelix tRNA theorem describes evolution of type I and type II tRNAs to the last nucleotide. In databases, type I and type II tRNA V loops (V for variable) were improperly aligned, but alignment based on the theorem is accurate. Type II tRNA V arms were a 3’-acceptor stem (initially CCGCCGC) ligated to a 5’-acceptor stem (initially GCGGCGG). The type II V arm evolved to form a stem-loop-stem. In Archaea, tRNALeu and tRNASer are type II. In Bacteria, tRNALeu, tRNASer and tRNATyr are type II. The positioning of the type II V arm is determined by the number of unpaired bases just 5’ of the Levitt base (Vmax). For Archaea, tRNALeu has 2 unpaired bases, and tRNASer has 1 unpaired base. For Bacteria, tRNATyr has 2 unpaired bases, tRNALeu has 1 unpaired base and tRNASer has 0 unpaired bases. Thus, the number of type II tRNAs is limited by the possible set points of the arm. From analysis of aminoacyl-tRNA synthetase structures, contacts to type II V arms appear to adjust allosteric tension communicated primarily via tRNA to aminoacylating and editing active sites. To enhance allostery, it appears that type II V arm end loop contacts may tend to evolve to V arm stem contacts.

Evolutionary, sequence and structural analyses of tRNA variable (V) loops provides a new understanding. Type I tRNA V loops have a primordial length of 5 nt, and type II tRNA V loops have a primordial length of 14 nt. Sequence-based alignments of type I and type II V loops gave deceptive results. Type II V loops are characterized by the trajectory of the V arm, the size and sequence of the loop and the first and last V loop nucleotides and their known contacts. Depending on the V arm trajectory, type II V stems and loops can be interaction sites for aminoacyl-tRNA synthetases. So, type II V arms for tRNALeu, tRNASer and tRNATyr (found in Bacteria) were coevolved and selected to distinguish determinants to support cognate tRNA charging. The alignment of type I and type II V loops was adjusted based on tRNA evolution. Results are consistent with Archaea being an older and simpler life form than Bacteria. TRNAome sequences were derived from radiation of an ordered tRNAPri (Pri for primordial) sequence comprised of known RNA repeats and inverted repeats. V loop and tRNA sequences, therefore, convey a history of the primary successful pathway in the origin of life.

The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions. The study developed a novel method for evaluating the freshness of citrus fruits by integrating near-infrared spectroscopy with the nonlinear data processing capabilities of a BP neural network. This approach utilizes specific wavelength analysis to distinguish between fresh and non-fresh fruits effectively. Advanced preprocessing techniques are employed to remove spectral anomalies, enhancing the network's ability to accurately identify crucial quality indicators like sugar content. Concurrently, an experiment utilising a MATLAB-based BP neural network optimised the number of hidden layer nodes, identifying 61 as optimal. This configuration achieved impressive metrics, including a mean squared error of 0.0025665 and a root mean squared error of 49.8214, over 1000 training iterations with an 80% learning rate. The model demonstrated a high accuracy rate of 97.6275%, confirming its precision and reliability in assessing citrus freshness. This synergy between advanced neural network processing and spectroscopic techniques marks a significant advancement in agricultural quality assessment, setting new standards for speed and efficiency in data processing.

Preconception or prenatal carrier screening for hereditary deafness is an effective early intervention strategy to reduce the incidence of newborn deafness, but current research is limited. This study aimed to investigate the carrier frequencies of common deafness genes in the Chinese population and to follow up on pregnancy outcomes in high-risk couples. Carrier screening for common deafness genes in the Chinese population, including the GJB2 and SLC26A4 genes, was performed using next-generation sequencing technology. Of the 9,993 subjects screened, the carrier rate was 2.86% for the GJB2 gene and 2.63% for the SLC26A4 gene. Of the six high-risk couples, four made alternative reproductive decisions (three with prenatal diagnosis and one with preimplantation genetic testing), with consequent successful termination of the birth of two affected fetuses. The frequencies of preconception or prenatal carrier screening for the deafness genes GJB2 and SLC26A4 in 9,993 subjects from China in this study were 2.86% and 2.63%, respectively. In addition, four out of six high-risk couples made alternative reproductive decisions, followed by the successful prevention of the birth of two affected fetuses. These findings confirmed the clinical utility of preconception or prenatal carrier screening for hereditary deafness.

This study aimed to investigate how transplanting date affects the agronomic and grain quality traits of two early maturing rice varieties. The experiment was conducted in the rice research field of Chungnam Agricultural Research and Extension Services, South Korea and rice materials were transplanted at intervals of approximately 15 days from April 16 to July 16 in 2019 and 2020. Results showed that agronomic and grain quality traits varied according to the transplanting date, and earlier transplanting resulted in the longer period of days from transplanting to heading (DTH). The spikelet number m-2 was highly correlated with the milled rice yield (r = 0.963** for Jinbuol, r = 0.909** for Yeoreumi) and it significantly decreased as the transplanting date was delayed, which was leading to lower yield. Environmental factors, the mean temperature during the grain filling stage, had a negative correlation with head rice rate (r2 = 0.825** for Jinbuol, r2 = 0.803** for Yeoreumi), and the number of days from transplanting to heading showed negative correlation with protein content (r2 = 0.777** for Jinbuol, r2 = 0.833** for Yeoreumi). Therefore, increasing the number of days from transplanting to heading date can lead to higher milled rice yield and lower protein content, and avoiding heading dates on July 17 can improve the appearance traits. As a results, it is suggested that early transplanting is advantageous to increase the milled rice yield and grain quality of early maturing rice.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

This paper investigates the dynamic properties of artificial neural networks using differential equations and explores the influence of parameters on stability and neural oscillations. By analyzing the equilibrium point of the differential equations, we identify conditions for asymptotic stability and criteria for oscillation in artificial neural networks. Furthermore, we demonstrate how adjusting synaptic weights between neurons can effectively control stability and oscillation. The proposed model offers potential insights into the malfunctioning mechanisms of biological neural networks implicated in neurological disorders like Parkinson's disease tremors and epilepsy seizures, which are characterized by abnormal oscillations.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

Five new perylenequinone derivatives, altertoxins VIII-XII (1-5), as well as one known compound cladosporol I (6), were isolated from the fermentation broth of Cladosporium sp. KFD33 from a blood cockle from Haikou Bay, China. Their structures were determined based on spectroscopic methods and ECD spectra analysis along with quantum ECD calculations. Compounds 1-6 exhibited quorum sensing inhibitory activities against Chromobacterium violaceum CV026 with MIC values of 30, 30, 20, 30, 20 and 30 μg/well, respectively.

We constrain two dynamical dark energy models that are parametrized by the logarithm form of $w(z)=w_{0}+w_{1}\left(\frac{\ln (2+z)}{1+z}-\ln 2\right)$ and the oscillating form of $w(z)=w_{0}+w_{1}\left(\frac{\sin(1+z)}{1+z}-\sin(1)\right)$. Comparing with the Chevallier-Polarski-Linder (CPL) model, the two parametrizations for dark energy can explore the whole evolution history of the universe properly. Using the current mainstream observational data including the cosmic microwave background data and the baryon acoustic oscillation data as well as the type Ia supernovae data, we perform the $\chi^2$ statistic analysis to global fit these models, finding that the logarithm parametrization and the oscillating parametrization are almost as well as the CPL scenario in fitting these data. We make a comparison for the impacts of the dynamical dark energy on the cosmological constraints on the total mass of active neutrinos. We find that the dark energy properties could significantly change the fitting results of neutrino mass. Looser constraints on $\sum m_{\nu}$ are obtained in the logarithm and oscillating models than those derived in the CPL model. Consideration of the possible mass ordering of neutrinos reveals that the most stringent constraint on $\sum m_{\nu}$ appears in the degenerate hierarchy case.

A digital twin is a virtual representation that serves as the real-time digital counterpart of a physical object or system. Recent advancements have extended the concept of digital twins to humans, incorporating complex biological data such as DNA (Predictiv Care, Inc.) and immune system profiles. These sophisticated models go beyond mere pictorial representations, offering a more holistic digital reflection. However, a significant gap remains. The current human digital twin models are not capable of learning one’s preferences. In this pilot study, we introduce Diginality, a chatbot powered by HyperCLOVA X, a Large Language Model (LLM) developed by NAVER, Inc. Diginality, learns one’s preferences with custom training from data collected by interview-style questions on the user’s topic of interest. Our findings demonstrate that Diginality successfully answers one’s preferences, thereby adding a new dimension to the concept of human digital twins. This work represents a pioneering step towards creating a more comprehensive and psychologically nuanced human digital twin.

Transcutaneous injection laryngoplasty is a well-known procedure for treating paralyzed vocal fold by injecting augmentation material into it. Hence, vocal fold localization plays a vital role in the preoperative planning as the fold location is required to determine the optimal injection route. In this communication, we propose a mirror environment based reinforcement learning (RL) algorithm for localizing the right and left vocal folds in preoperative neck CT. RL-based methods commonly showed noteworthy outcome in general anatomic landmark localization problem in the recent years. However, such methods suggest training individual agent for localizing each fold, though the right and left vocal folds are located in close proximity and have high feature-similarity. Utilizing the lateral symmetry between the right and left vocal folds, the proposed mirror environment allows for a single agent for localizing both the folds by treating the left fold as a flipped version of the right fold. Thus, localization of both folds can be trained using a single training session which utilizes the inter-fold correlation and avoids redundant feature learning. Experiment with 120 CT volumes showed improved localization performance and training efficiency of the proposed method compared with the standard RL method.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

Considering the aging society and budget constraints, a strategy for reforming public transportation welfare policies is essential for sustainability. Among the various transportation welfare policies, fare discount policies are provided to specific age groups, and most countries offer benefits to several public transportation. South Korea provides a fare-free policy limited to subways, and the need for policy modification is emerging due to sustainability problems caused by an aging society. Hence, the scope of the policy should be expanded to all travel modes, but the discount rate should be reduced, or the target group should be reduced in consideration of the budget. This study proposes a travel mode to focus on by city through the preference of the elderly. The latent class model is employed to classfy stated preference data collected from the survey. The estimation results show a significant preference heterogeneity depending on the level of subway supply by region, and a policy focused on subways would be more reasonable in cities with sufficient subway infrastructure. Hence, regarding sustainability, it may be more appropriate to focus on specific means than to provide the same discount policy for all public transport.

The advent of deep learning has completely reshaped our world. Now, our daily life is fulfilled with many well-known applications that adopt deep learning techniques, such as self-driving cars and face recognition. Furthermore, robotics developed more forms of technology which share the same principle with face recognition, such as hand pose recognition and fingerprint recognition. Image recognition technology requires a huge database and various learning algorithms, such as convolutional neural network and recurrent neural network, that requires lots of computational power, such as CPUs and GPUs. Thus, clients could not be satisfied with the computational resource of the local machine. The cloud resource platform emerged at a historic moment. Docker containers play a significant role of microservices-based applications in the next generation. However, it could not guarantee the quality of service. From clients’ perspective, they have to balance the budget and quality of experiences (e.g. response time). The budget leans on individual business owners and the required Quality of Experience (QoE) depends on usage scenarios of different applications, for instance, an autonomous vehicle requires real-time response, but, unlocking your smartphone can tolerate delays. Plenty of on-going projects developed user-oriented optimization resource allocation to improve the quality of the service. Considering the users’ specifications, including accelerating the training process and specifying the quality of experience, this thesis proposes two differentiate containers scheduling for deep learning applications: TRADL and DQoES .

Prediction of protein-ligand binding affinities is crucial for computational drug discovery. A number of deep learning approaches have been developed in recent years to improve the accuracy of such affinity prediction. While the predicting power of these systems have advanced to some degrees depending on the dataset used for model training and testing, the effects of the quality and quantity of the underlying data have not been thoroughly examined. In this study, we employed erroneous datasets and data subsets of different sizes, created from one of the largest databases of experimental binding affinities, to train and evaluate a deep learning system based on convolutional neural networks. Our results show that data quality and quantity do have significant impacts on the prediction performance of trained models. Depending on the variations in data quality and quantity, the performance discrepancies could be comparable to or even larger than those observed among different deep learning approaches. In particular, the presence of proteins during model training leads to a dramatic increase in prediction accuracy. This implies that continued accumulation of high-quality affinity data, especially for new protein targets, is indispensable for improving deep learning models to better predict protein-ligand binding affinities.

In this paper, we investigate the new degenerate Daehee polynomials and numbers which are called the degenerate Daehee polynomials of the second kind, and derive some new and interesting identities and properties of those polynomials.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

To clarify whether cryptochrome contributes to stem elongation and flowering promoted by blue lights associated with low phytochrome activity, wild-type Arabidopsis was compared with its cryptochrome-deficient mutants and cryptochrome-overexpressing transgenic plants. Results indicated that the promotion effects were mainly related to low CRY1 activity, despite partial involvement of high-activity CRY2.

The research examines the relationship between self-rated health situation and personal percep-tion of heat waves, and how social linkage of communities would be a moderator variable in residents’ perception of heat waves in Taiwan. This study uses the questionnaire conducted by Sinica “Responsive Capacity under Heat Wave: The Perspectives of the Locals”(2019), using OLS method for estimating the unknown parameters in multiple regression model. The author finds that the correlation of self-rated health situation and perception toward heat is significantly posi-tive. Also, social linkage in communities affects strongly as a moderator variable: While the sat-isfaction to with their community could reduce negative reaction to heat, contacts with neighbors could increase possibility people feel uncomfortable in high-temperature situation. This study ex-hibits the effects of social environment on community, and expects further related researches or practices to strengthen capability to resist heat wavesƒ for Taiwanese residents.

In this perspective article, we ponder topographical enhancements of artificial neural networks. In our recent paper in JMLR, we proved a quasi-equivalence between the network width and depth and also discussed the power of intra-links, which can be viewed as network height. In 1982, Hopfield published a network to model human associative memory, which contains many loops for dynamic evolution toward fixed points. Based on noising-denoising loops, diffusion models are recently developed to enable Bayesian modeling and inference with big data. Furthermore, we envision development of multi-AI-agent systems through “netware” engineering as a quantum leap of software engineering for emergent behaviors and autonomous AI at individual and population levels. We believe that the novel use of links and loops in space and time via multi-scale coupling would catalyze the next-generation neural networks.

Evodiamine is a bioactive alkaloid that is specified as a biomarker for the quality assessment of Evodia rutaecarpa and for traditional Chinese medicines containing this plant. We previously reported that quantitative structure-activity modeling indicated that evodiamine may cause cardiotoxicity. However, previous investigations have indicated that evodiamine has beneficial effects in patients with cardiovascular diseases and there are no previous in vitro or in vivo reports of evodiamine-induced cardiotoxicity. The present study investigated the effects of evodiamine on primary cultured neonatal rat cardiomyocytes in vitro, and on zebrafish in vivo. Cell viability was reduced in vitro, where evodiamine had a 24-h 50% inhibitory concentration of 28.44 µg/mL. Cells exposed to evodiamine also showed increased lactate dehydrogenase release and maleic dialdehyde levels, and reduced superoxide dismutase activity. In vivo, evodiamine had a 10% lethal concentration of 354 ng/mL and induced cardiac malfunction, as evidenced by changes in heart rate and circulation, and pericardial malformations. This study indicated that evodiamine could cause cardiovascular side effects involving oxidative stress. These findings suggest that cardiac function should be monitored in patients receiving preparations containing evodiamine.

Aging is associated with muscle atrophy and fatty infiltration of skeletal muscle. The multifidus muscle stabilizes the lumbar spine and undergoes adipose accumulation with age, leading to functional decline in the elderly. Therefore, quantitative assessment of the multifidus muscle can be beneficial for the elderly when formulating treatment strategies and reducing future complications. Fifty-seven patients (mean age, 73.89 ± 6.09; 23 male patients) who underwent lumbar Magnetic resonance imaging (MRI) were prospectively recruited. The cross-sectional area (CSA) of the multifidus from the L2-S1 level and the CSA of the L4-5 level psoas muscle were measured. The functional CSA (fCSA) of the multifidus muscle was measured by excluding the fat infiltration area from the multifidus CSA. The CSA to fCSA ratio was obtained by multiplying 100 by the value obtained by dividing CSA by the fCSA. Pfrrmann classification was used to evaluate the degree of disc degeneration. The functional disability measurements were the Short Physical Performance Battery (SPPB), Berg Balance Scale (BBS), grip strength, and functional reach test (FRT). Pearson's correlation analysis was used to examine the relationship between the functional disability measurements and the multifidus muscle. The CSA to fCSA ratio value was relatively constant at each spine level and showed a significant correlation with the SPPB, grip strength, FRT, and psoas index (p<0.05). However, degree of disc and multifidus muscle degeneration were not statistically significant. So, age-related changes play a significant role in developing back muscle fatty infiltration than disc dgeneration. Moreover, Grip strength showed a stronger relationship with the quality of the multifidus muscle than other functional disability measurements.

The betel nut chewing habit of taxi drivers has shown that can promote companionship, relaxation, and emotional stability at work. 19.3% of betel nut behaviors are instigated by an invitation among drivers to engage in the habit. The objective of this study was to explore the impact of social learning, subjective norm, and self-efficacy on betel nut chewing in taxi drivers in Taiwan. We conducted a cross-sectional study on taxis’ driver of betel nut behaviour and measured their evaluations of its consequences using a self-report questionnaire. Other variables include socio-demographic characteristics and chewing-related experience. The overall variance is 44.5% in socio-demographic variable, social learning, self-efficacy, and subjective norm. Results show that the variables of affected betel nut chewing behavior, driving years has the strongest influence, followed by learning about betel nut from the media, relatives, and friends, and education level, which positively affect betel nut chewing behavior. Findings indicated that education related to quitting betel nut chewing, significant others, and rules of the taxi fleet are adopted to design a plan for quitting betel chewing to reduce the positive expectations of taxi drivers for betel nut chewing and decrease their betel nut chewing behavior.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

Decades of research identified numerous gene biomarkers of cardiac diseases whose restored sequence or/and expression level was hoped to recover the normal cardiac function. However, each human has unique and dynamic pathophysiological characteristics resulting from the unrepeatable combination of favoring factors such are: race, sex, age, medical history, diet, stress, exposure to toxins, habits etc. As such, no treatment fits everybody and finding personalized solutions is a top priority for medicine of 21st century. The Genomic Fabric Paradigm (GFP) provides the most theoretically possible comprehensive characterization of the transcriptome, its alterations in disease and recovery following a treatment. By attaching to each gene the independent average expression level, expression variation and expression coordination with each other gene, GFP delivers thousands times more information than the traditional analysis. This report presents the theoretical bases of the GFP and some applications to our microarray data from mouse models of post ischemic, and constant and intermittent hypoxia-induced heart failure. The GFP analyses revealed novel transcriptomic aspects of the gene expression control and networking under ischemic conditions. Through all-inclusive characterization of the transcriptome and the unrepeatable gene hierarchy in each condition, GFP is an essential avenue towards development of a truly personalized cardiogenomic therapy.

Embracing innovative digital technologies within educational systems is essential for overcoming challenges in modern learning environments, especially in the post-COVID-19 era. Teaching sustainability management in higher education institutions with innovative digital tools plays a fundamental role in the transition toward sustainable societies. Suitable game design elements play a significant role in facilitating sustainable learning. This study explored the effectiveness of incorporating business simulation games with project-based learning (PBL) in a flipped classroom setting. This approach was adopted within the context of a university cross-border e-commerce course to prepare students for acquiring 21st -century skills as higher-order thinking skills in a rapidly changing educational landscape. A quasi-experimental method was employed, involving a total of 60 university students from China's Zhejiang Province. Participants completed an online questionnaire designed to assess their learning engagement across three dimensions (cognitive, emotional, and behavioral) as well as their higher-order thinking skills (problem-solving, critical thinking, and creativity). The results show that the business simulation games combined with flipped classroom learning had a significantly positive impact on students’ learning outcomes, enhancing their problem-solving, critical thinking, and creative capabilities. Importantly, this approach also improved student engagement and promoted sustainable practices by applying real-life scenarios in an interactive environment. We conclude that business simulation games integrated with project-based learning (PBL) in flipped classroom settings represent a valuable educational approach. This approach not only enhances learning engagement but also fosters the development of higher-order thinking skills, encouraging students to adopt sustainable learning practices.

The intricate relationship between physical and social environments within organizations plays a pivotal role in shaping sustainable innovation endeavors. This paper presents a comprehensive analysis of two key dynamics that have garnered substantial scholarly attention for promoting sustainable innovation: the physical environment and the organizational climate. To elucidate the intricate interplay between these dynamics, we propose a novel three-dimensional framework that guides the modeling of the intricate processes through which the physical environment and innovation climate synergistically influence innovation outcomes. Building on this framework, we delve into an in-depth literature review concerning physical environments that exert a significant impact on innovation. Through this review, we identify and elaborate on four pivotal elements of the physical environment: communality, personalization, comfort, and healthiness. Leveraging insights gleaned from this review, we outline two promising avenues for future research in the realm of the physical environment's interaction with the innovation climate. Furthermore, we underscore the critical importance of adopting an interdisciplinary approach that seamlessly integrates insights from both the physical and social domains to comprehensively understand the sustainable innovation landscape.

The mangrove plant Acanthus ilicifolius and its relative, A. mollis, have been previously proved to possess diverse pharmacological effects. Therefore, evaluating the differentially expressed proteins of these species under tidal flooding stress is essential to fully exploit and benefit from their medicinal values. The roots of A. ilicifolius and A. mollis were exposed to 6 h of flooding stress per day for 10 days. The dry weight, hydrogen peroxide (H2O2) content, anatomical characteristics, carbon and energy levels, and two-dimensional electrophoresis coupled with MALDI-TOF/TOF MS technology were used to reveal the divergent flooding resistant strategies. A. ilicifolius performed better under tidal flooding stress, which was reflected in the integrity of the morphological structure, more efficient use of carbon and energy, and a higher percentage of up-regulated proteins associated with carbon and energy metabolism. A. mollis could not survive in flooding conditions for a long time, as revealed by incomplete cell structures of the roots, less efficient use of carbon and energy, and a higher percentage of down-regulated proteins associated with carbon and energy metabolism. Energy provision and flux balance played a role in the flooding tolerance of A. ilicifolius and A. mollis.

The root system plays an irreplaceable role in plant growth. Its improvement can increase crop productivity. However, such system is still mysterious for us. The underlying mechanism has not been fully uncovered. The investigation on proteins related to the root system is an important means to complete this task. In the previous time, lack of root-related proteins makes it impossible to adopt machine learning methods for designing efficient models for the discovery of novel root-related proteins. Recently, a public database on root-related proteins was set up and machine learning methods can be applied in this field. In this study, we proposed a machine learning based model, named Graph-Root, for identification of root-related proteins. The features derived from protein sequences and one network were extracted, where the former features were processed by graph convolutional neural network and multi-head attention, and the later features abstracted the linkage between proteins. These features were fed into the fully connected layer to make prediction. The 5-fold cross-validation and independent tests suggested its good performance. It also outperformed the only one previous model, SVM-Root. Furthermore, the importance of each feature type and component in the proposed model was investigated.

This paper presents ConF, a novel deep learning model designed for accurate and efficient prediction of non-coding RNA families. NcRNAs are essential functional RNA molecules involved in various cellular processes, including replication, transcription, and gene expression. Identifying ncRNA families is crucial for comprehensive RNA research, as ncRNAs within the same family often exhibit similar functionalities. Traditional experimental methods for identifying ncRNA fam-ilies are time-consuming and labor-intensive. Computational approaches relying on annotated secondary structure data face limitations in handling complex structures like pseudoknots and have restricted applicability, resulting in suboptimal prediction performance. To overcome these chal-lenges, ConF integrates mainstream techniques such as residual networks with dilated convolutions and cross multi-head attention mechanisms. By employing a combination of dual-layer convolu-tional networks and BiLSTM, ConF effectively captures intricate features embedded within RNA sequences. This feature extraction process leads to significantly improved prediction accuracy compared to existing methods. Experimental evaluations conducted on a ten-fold publicly available dataset demonstrate the superiority of ConF in terms of accuracy, sensitivity, and other perfor-mance metrics. Overall, ConF represents a promising solution for accurate and efficient ncRNA family prediction, addressing the limitations of traditional experimental and computational methods.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

This study presented a novel and sustainable method for producing chitin nanocrystals (PA-ChNCs) using phosphoric acid hydrolysis. The produced PA-ChNCs were used as stabilizers for Pickering emulsions and their physicochemical properties as well as stabilization mechanisms were systematically investigated. The PA-ChNCs exhibited small particle sizes and high surface areas, enabling an effective adsorption at the oil/water interface, which prevented coalescence in Pickering emulsions. The particle size and surface charge PA-ChNCs were strongly pH-dependent, which were critical factors for stabilizing Pickering emulsions. The study showed that emulsions with higher O:W ratios (50%) exhibited larger droplets but greater viscosity, forming a stable gel-like matrix that was more stable than emulsions with other O:W ratios after storage for 30 days. Emulsions with higher PA-ChNCs concentrations (2.0 wt%) and higher pH values (pH 10) showed small droplets and high viscosity, leading to stable emulsions. This research contributes to the development of sustainable and effective emulsifiers for use in the food industry, making utilization of seafood waste in an eco-friendly manner possible. Overall, this study highlights the potential of using newly developed PA-ChNCs as stabilizers for Pickering emulsions in food products.

This study was conducted to examine the moderating and mediating effect of ego - resilience, parenting attitude, and peer attachment in the relation between smartphone dependency and aggression. Participants were 1,863 youths using a smartphone among the first middle school students responded in the 7th Korean Children and Youth Panel Survey (KCYPS) conducted by the National Youth Policy Institute in Korea. The data were analyzed by descriptive statistics, a correlation, and a hierarchical regression analysis. First, ego-resilience showed a partial mediating effect on the relationship between smartphone dependency, aggression and significant moderating effects were revealed. Second, parenting behavior showed a partial mediating effect on the relationship between smartphone dependency and aggression, with no moderating effects seen. Third, peer attachment had a partial mediating effect on the relationship between smartphone dependency and aggression, with no moderating effects seen. The research suggested the mental health and growth of students could be improved by applying various nursing and health care programs to improve ego-resilience, parenting behavior and peer attachment as they grow into adulthood.

Types of DNA recombination include homologous recombination and nonhomologous recombination. Homologous DNA recombination is a general term that includes exchange of information between chromatids: (reciprocal) crossing-over, gene conversion, and post-meiotic segregation. Gene conversion is now thought to be a type of non-Mendelian segregation of heterozygous markers near the recombination initiation site. Thus, it includes both gene conversion and post-meiotic segregation previously described. DNA non-HR including transpositional recombination and site-specific recombination. Our understanding of the molecular mechanism by which DNA recombination occurs has significantly increased in the past decades. Currently The synthesis-dependent strand annealing model is now thought to give rise to most or all noncrossovers, with the double-strand-break repair model forming mainly crossovers. The Shapiro model proposed by Dr. J. Shapiro explains the molecular mechanism of transpositional recombination. Site-specific recombination results from another distinct model. We previously proposed a novel theory which can provide a more reasonable and simpler explanation accounting for DNA HR including the 3 classes of recombinogenic events described above. In the new supplementedly molecular model, DNA meiotic recombination can be initiated by a copy choice mechanism, that is, copying part of 1 single-stranded DNA template, followed by DNA polymerase switching to another single-stranded DNA template, and then resuming the following DNA synthesis along the new template. The current review suggests that transpositional recombination and site-specific recombination should be initiated by copy choice during DNA synthesis rather than break/join mechanism. The work indicates that review of DNA nonhomologous recombination are very necessary. The novel theory would challenge earlier models accounting for transpositional recombination and site-specific recombination and would be critical to the understanding of the mechanisms. We hope copy choice initiating DNA nonhomologous recombination will be one of the concepts that are explored. Proper and specific experiments are required to reconstruct the detailed mechanism described here.

Vibration signal analysis is regarded as a fundamental approach in diagnosing faults in rolling bearings, and recent advancements have shown notable progress in this domain. However, the presence of substantial background noise often results in the masking of these fault signals, posing a significant challenge for researchers. In response, an Adaptive Denoising Autoencoder (ADAE) approach is proposed in this paper. The data representations are learned by the encoder through convolutional layers, while the data reconstruction is performed by the decoder using deconvolutional layers. Both the encoder and decoder incorporate adaptive shrinkage units to simulate denoising functions, effectively removing interfering information while preserving sensitive fault features. Additionally, dropout regularization is applied to sparsify the network and prevent overfitting, thereby enhancing the overall expressive power of the model. To further enhance ADAE's noise resistance, shortcut connections are added. Evaluation using publicly available datasets under scenarios with known and unknown noise demonstrates that ADAE effectively enhances the signal-to-noise ratio in strongly noisy backgrounds, facilitating accurate diagnosis of faults in rolling bearings.

Fractures of the talar neck and body are associated with spine fractures and scoliosis deformity, which affect cosmetic appearance and cause difficulty in ambulation. The implant design for talus surgery is thriving as a functional alternative in case of severe talar destruction, focusing on segmentation and reconstruction of the talus’s shape. However, manual segmentation of the talus is time-consuming and subjective. In this study we exploited the automatic segmentation framework to efficiently train a deep learning-based model to accurately segment the talus based on computed tomography imaging. We developed three model configurations with nnU-Net and investigated their Dice similarity coefficients (DSC) and 95% Hausdorff distances (HD95) for talus segmentation on a CT image dataset. The three configurations performed well (DSC > 0.95, HD95 < 0.6). When tested on the same samples, one of the configurations was more efficient while ensuring higher accuracy. We propose to focus on talus anatomic variations with increasing age based on this framework and apply it to clinical trials at the next stage.

Though the energy density of lithium-ion batteries continues to increase, safety issues related with the internal short-circuit and the resulting combustion of highly flammable electrolyte impede the further development of lithium-ion batteries. It has been well-accepted that a thermal stable separator is important to postpone the entire battery short-circuit and thermal-runaway. Traditional methods to improve the thermal stability of separators includes surface modification and/or developing alternate material systems for separators which may always affect the battery performance negatively. Herein, a thermostable and shrink-free separator with little compromise in battery performance is prepared by coaxial electrospinning and tested. The separator consists of core-shell fiber networks where poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) layer serves as shell and polyacrylonitrile (PAN) as the core. This core-shell fiber network exhibits little or even no shrinking/melting at elevated temperature over 250 °C. Meanwhile, it shows excellent electrolyte wettability and can take large amount of liquid electrolyte three times more than that of conventional Celgard 2400 separator. In addition, the half-cell using LiNi1/3Co1/3Mn1/3O2 as cathode and the aforementioned electrospun core-shell fiber network as separator demonstrates superior electrochemical behavior, stably cycling for 200 cycles at 1 C with a reversible capacity of 130 mAh g-1 and little capacity decay.

With the development of society and the economy, the unified planning of architectural style has become a difficult problem in the competition between urban expansion and the protection of tra-ditional buildings in villages and towns. At the same time, it also allows people to re-examine the appearance and quality of life of traditional village buildings. In this paper, the Conditional Gen-erative Adversarial Network (CGAN) is used to construct a method of building facade generation in villages and towns, so as to gradually realize the governance of the style of villages and towns. At the same time, it has also reduced the restoration of the facades of villages and towns and the graphic design of rural tourism products, showing its application value and potential in the field of planning and design. In the research, taking villages and towns in the Wuyishan area of China as an example, the method is used to carry out model training, image generation, and comparison of the derivation results of different assumed building contours and product contours. The research shows that: (1) CGAN can be used to derive and design the facades of conventional civil buildings in villages and towns. (2) In terms of product graphic design, especially the common tourist cultural products fans and water cups, show significant potential. (3) The construction of this method is not only applicable to villages and towns under the World Heritage City, but can be further promoted and used in the future for cities and villages that have a demand for architectural style consistency.

In recent years, there has been significant growth in the ubiquity and popularity of three dimensional(3D) point clouds, with an increasing focus on the classification of 3D point clouds. To extract richer features from point clouds, many researchers have turned their attention to various point set regions and channels within irregular point clouds. However, this approach has limited capability in attending to crucial regions of interest in 3D point clouds and may overlook valuable information from neighboring features during feature aggregation. Therefore, this paper proposes a novel 3D point cloud classification method based on global attention and adaptive graph convolution. The method consists of two main branches: the first branch com-putes attention masks for each point, while the second branch employs adaptive graph convolu-tion to extract global features from the point set. It dynamically learns features based on point interactions, generating adaptive kernels to effectively and precisely capture diverse relationships among points from different semantic parts. Experimental results demonstrate that the proposed model achieves 93.8% in overall accuracy and 90.8% in average accuracy on the ModeNet40 dataset.

The security of several full homomorphic encryption (FHE) schemes depends on the hardness of the approximate common divisor (ACD) problem. The analysis of attack and defense against the system is one of the frontiers of cryptography research. In this paper, the performance of existing algorithms, including orthogonal lattice, simultaneous diophantine approximation, multivariate polynomial and sample pre-processing are reviewed and analyzed for solving the ACD problem. Orthogonal lattice (OL) algorithms are divided into two categories (OL-$\land$ and OL-$\vee$) for the first time. And an improved algorithm of OL-$\vee$ is presented to solve the GACD problem. This new algorithm works well in polynomial time if the parameter satisfies certain conditions. Compared with Ding and Tao's OL algorithm, the lattice reduction algorithm is used only once, and when the error vector $\mathbf{r}$ is recovered in Ding et al.'s OL algorithm, the possible difference between the restored and the true value of $p$ is given. It is helpful to expand the scope of OL attacks.

Miniature sensors are key components for the applications in the Internet of Things (IoT), wireless sensor networks, autonomous vehicles, smart cities and smart manufacturing. As a miniature and self-powered magnetic sensor, Wiegand sensor possesses the advantageous traits including changing-rate-independent output, low cost, and remarkable repeatability and reliability. Typical Wiegand sensor requires hard magnetic pole pieces that provide external fields for triggering voltage outputs that are called Wiegand pulses. However, the wire-shaped sensing element of Wiegand sensor is the critical issue that limits the design, selection, and adoption of the external triggering magnets. Currently, the widely used pole piece materials are rare-earth magnets. However, adopting rare-earth magnets brings strong stray fields, causing electromagnetic interference (EMI) problem. In this study, patterned CoNiP hard magnets were electrodeposited on flexible substrates through microfabrication. Origami magnetization was utilized to control the resultant stray fields, and hence the pole piece of CoNiP magnets can successfully trigger the output of Wiegand pulse. In comparison, the output voltage of the triggered pulse acquired through the patterned CoNiP magnets is comparable to that by using the rare-earth magnets. Furthermore, both the volume (meanwhile the weight) of the Wiegand sensor and the EMI issue can be significantly reduced and mitigated by the CoNiP magnets.

Polyacetylene phytochemicals are emerging as potentially responsible for the chemoprotective effects of consuming apiaceous vegetables. There is some evidence suggesting that polyacetylenes impact carcinogenesis by influencing a wide variety of signalling pathways, which are important in regulating inflammation, apoptosis, cell cycle regulation, etc. Studies have shown a correlation between human dietary intake of polyacetylene-rich vegetables with reduced risk of inflammation and cancer. Polyacetylene supplementation can influence cell growth, gene expression, and immunological responses, and reduce tumour number in rat and mouse models. Cancer chemoprevention by dietary polyacetylenes involves several mechanisms, including effects on inflammatory cytokines, the NF-κB pathway, antioxidant response elements, UPR pathway, growth factor signalling, cell cycle progression, and apoptosis. This review summarises the published research on falcarinol-type polyacetylene compounds and their mechanisms of action regarding cancer chemoprevention and treatment, and also identifies some gaps in our current understanding of the health benefits of these polyacetylenes.

The Connor–Davidson Resilience Scale (CD-RISC) and the Brief Resilience Scale (BRS) are two widely used scales to measure resilience. Although both scales seek to assess an individual’s ability to recover from and adapt to disruptions or stressful events, they may capture different aspects of resilience. While the CD-RISC focuses on resources that can help individuals recover from and adapt to disruptions or stressful events, the BRS directly measures one’s ability to bounce back or be resilient. The aim of this study is to empirically examine the differences between the CD-RISC and the BRS. Two samples (n = 202, 246) consisting of undergraduate students from Taiwan were used. The results of confirmatory factor analysis show that the CD-RISC and the BRS are highly correlated but still distinct. The results of regression analyses show that the CD-RISC and the BRS have unique predictive effects on depression and life satisfaction. The research findings suggest that the CD-RISC and the BRS capture different aspects of resilience. For future research on resilience, researchers should pay attention to the differences between these scales and choose the one that most closely fits their research purpose.

This study aims to understand the contents of debriefing performance in simulation education and its results by comprehensively examining the learning performance of the education ac-cording to the difference in the debriefing methods employed in domestic and overseas nursing simulation training. This is a literature review conducted to identify the effect of debriefing of simulation nursing practice education. The existing literature was found in electronic databases using Pubmed, Embase, MEDLINE complete, PsycINFO, Web of Science, CINAHL, the Cochrane Library, KoreaMed, National Discovery for Science Leaders, and Research Information Sharing Service and the key words were “nurse,” “nursing student,” “simulation,” “simulator,” “stand-ardized patient,” “debriefing.” Finally, 32 studies were analyzed. All the studies were conducted from 2012 to 2021. A total of 11 RCT, 17 quasi-experimental studies, 3 mixed method studies and 1 pilot study were identified. The debriefing process used media, structured questionnaires, and a method of teaching or peer-led debriefing. The outcome variables that were statistically significant were skill, performance, knowledge, problem-solving competency, critical thinking disposition, clinical judgement, self-confidence, satisfaction, and debriefing quality evaluation. It is necessary to educate the debriefers who are responsible for strategy development and meeting effective debriefing goals.

The Diaphorina citri Kuwayama (D. citri) is one of the major pests in the citrus industry, which spreads Citrus Huanglongbing disease. It has developed resistance to chemical insecticides. Therefore, searching for greener solutions for pest management is critically important. The main aim of this study was to evaluate the repellent and insecticidal efficacy of essential oils (EOs) from four species of Myrtaceae plants: Psidium guajava (PG), Eucalyptus robusta (ER), Eucalyptus tereticornis (ET), and Baeckea frutescens (BF) against D. citri and to analyze their chemical composition. GC-MS analysis was performed, and the results indicated that the EOs of PG, ER, ET, and BF were rich in terpenoids, ketones, esters, and alcohol compounds. The repellent rate of all four EOs showed that it decreased with exposure time but increased with concentrations of EOs. Repellent rates ranged from 80.50% to 100.00% after treating D. citri for 6 hours with four EOs at 100% concentration and decreased to 67.71% to 85.49% after 24 hours of exposure. Among the compounds from the EOs tested, eucalyptol had the strongest repellent activity, with a 24-hour repellency rate of 100%. The contact toxicity bioassay results showed that all EOs have insecticidal toxicity to D. citri; the LC50 for nymphs was 36.47-93.15 mL/L, and for adults, it was 60.72-111.00 mL/L. These results show that when PG is used as the reference material, both ER, ET, and BF EOs have strong biological activity against D. citri, which provides a scientific basis for the further development of plant-derived agrochemicals.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

Digitized counter-diabatic (CD) optimization algorithms have been proposed and extensively studied to enhance performance in quantum computing by accelerating adiabatic processes while minimizing energy transitions. While adding approximate counter-diabatic terms can initially introduce adiabatic errors that decrease over time, Trotter errors from decomposition approximation persist. On the other hand, increasing the high-order nested commutators for CD terms may improve adiabatic errors but could also introduce additional Trotter errors. In this article, we examine the two-qubit model to explore the interplay between approximate CD, adiabatic errors, Trotter errors, coefficients and commutators. Through these analysis, we aim to gain insights into optimizing these factors for better fidelity, shallower circuit depth, and reduced gate number in near-term gate-based quantum computing.

Taxanes, particularly docetaxel (DTX), has been widely used for combination therapy of head and neck squamous cell carcinoma (HNSCC). For locally advanced unresectable HNSCC, DTX combined with cisplatin and 5-fluorouracil as a revolutionary treatment revealed an advantage in improvement of patient outcome. In addition. DTX plus immune check inhibitors (ICIs) showed low toxicity and increased response of patients with recurrent or metastatic HNSCC (R/M HNSCC). Accumulating data indicate that taxanes not only function as antimitotics but also impair diverse oncogenic signalings including angiogenesis, inflammatory response, ROS production, and apoptosis induction. However, despite an initial response, development of resistance remains a major obstacle to treatment response. Taxane resistance could result from intrinsic mechanisms such as enhanced DNA/RNA damage repair, increased drug efflux, and apoptosis inhibition, and extrinsic effects such as angiogenesis and interactions between tumor cells and immune cells. This review provides an overview of taxanes therapy applied in different stages of HNSCC and describe the mechanisms of taxane resistance in HNSCC. Through a detailed understanding the mechanisms of resistance may help developing the potential therapeutic methods and the effective combination strategies to overcome drug resistance.

Objective: To evaluate the effect of care bundles on treatment compliance and intestinal barrier function in patients with refractory septic shock in the intensive care units (ICUs). Methods: In this retrospective study, the clinical data of 94 patients with refractory septic shock admitted to our hospital between June 2020 and April 2022 were collected. Patients with routine nursing were included in the routine group, and those with care bundles were assigned to the care bundles group, with 47 cases in each group. Outcome measures included nursing efficiency, treatment compliance, sequential organ failure assessment (SOFA) score, acute physiology and chronic health evaluation (APACHE II) score, intestinal barrier function, inflammation factor level, treatment outcome and complications. Results: Care bundles resulted in significantly higher nursing efficiency and treatment compliance versus routine care (P<0.05). Patients receiving care bundles showed significantly higher SOFA scores and APACHE II scores than those receiving routine care (P<0.05). Intestinal fatty-acid binding protein (I-FABP), diamine oxidase (DAO), lactate, endotoxin, and intestinal dysfunction scores in the care bundles group were significantly lower than those in the conventional group after treatment (P<0.05). Care bundles were associated with significantly lower levels of procalcitonin (PCT) and hypersensitive C-reactive protein (hsCRP), shorter time to symptom relief, ICU treatment time, and duration of mechanical ventilation, and lower 28-d morbidity and mortality versus routine care (P<0.05). Patients in the care bundles group had a significantly lower incidence of complications than those in the routine group (P<0.05). Conclusion: Care bundles effectively enhance treatment compliance, improve intestinal barrier function and treatment outcomes, reduce the inflammatory response, and decrease the risk of SOFA score, APACHE II score, and complications in patients with refractory septic shock.

Objective: To evaluate the effect of care bundles on treatment compliance and intestinal barrier function in patients with refractory septic shock in the intensive care units (ICUs). Methods: In this retrospective study, the clinical data of 94 patients with refractory septic shock admitted to our hospital between June 2020 and April 2022 were collected. Patients with routine nursing were included in the routine group, and those with care bundles were assigned to the care bundles group, with 47 cases in each group. Outcome measures included nursing efficiency, treatment compliance, sequential organ failure assessment (SOFA) score, acute physiology and chronic health evaluation (APACHE II) score, intestinal barrier function, inflammation factor level, treatment outcome and complications. Results: Care bundles resulted in significantly higher nursing efficiency and treatment compliance versus routine care (P<0.05). Patients receiving care bundles showed significantly higher SOFA scores and APACHE II scores than those receiving routine care (P<0.05). Intestinal fatty-acid binding protein (I-FABP), diamine oxidase (DAO), lactate, endotoxin, and intestinal dysfunction scores in the care bundles group were significantly lower than those in the conventional group after treatment (P<0.05). Care bundles were associated with significantly lower levels of procalcitonin (PCT) and hypersensitive C-reactive protein (hsCRP), shorter time to symptom relief, ICU treatment time, and duration of mechanical ventilation, and lower 28-d morbidity and mortality versus routine care (P<0.05). Patients in the care bundles group had a significantly lower incidence of complications than those in the routine group (P<0.05). Conclusion: Care bundles effectively enhance treatment compliance, improve intestinal barrier function and treatment outcomes, reduce the inflammatory response, and decrease the risk of SOFA score, APACHE II score, and complications in patients with refractory septic shock.

Alopecia refers to the continuous shedding of hair from the scalp or other areas. Genetic factors are the most common of the variety of causes of alopecia. Male pattern baldness, also known as androgenic alopecia, is prevalent. Recently, the interest in hair loss treatment has increased due to the growing number of people experiencing anxiety and stress related to hair loss. Nepenthes kampotiana Lecomte is known for its anticancer effects, but its potential for preventing hair loss has not been researched. Therefore, this study focused on the hair loss prevention effects of N. kampotiana Lecomte ethanol extract (Nk-EE). The results showed that Nk-EE has a proliferative effect on human follicle dermal papilla cells and inhibited cell death. In vivo experiments using androgenic areata models showed that Nk-EE had a positive effect on a variety of biomarkers such as hair-to-skin ratio, hair type frequency, and hair thickness. The results of this study suggest that Nk-EE has the potential to be an effective treatment for androgenic alopecia.

Disparities between fold amplitude (A) and intrusion thickness (Hsill) are critical in identifying elastic or inelastic deformation in a forced fold. However, accurate measurement of these two parameters is challenging because of the limit in separability and detectability for the seismic data. In the TZ-47 exploring area from the Tarim Basin, Northwest China, we combined wireline data and 3-D seismic data, to accurately constrain the fold amplitude and total thickness of sills that inducing the roof uplift. The measurement results show that the forced fold amplitude is 155 m and the total sill thickness is 148.4 m. When using a magma density of 2.7 g/cm3, and solid rock density of 3 g/cm3, the molten magma thickness at the time of intrusion would be 153.8 m, which is almost no difference from the forced fold amplitude. Therefore, the TZ-47 fold is a pure elastic forced fold induced by emplacement of multiple sills. Measurement solely based on seismic data may not be able to detect some thin interlayers and may result in large errors.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

Currently, active and intelligent packaging have been developed to solve the spoilage problem for rich protein foods during storage, especially by adding anthocyanin extracts. In such film system, the antioxidant and antibacterial properties were dramatically increased by adding anthocyanins. The physicochemical properties were enhanced through interactions between active groups in anthocyanins and reactive groups in polymer chains. Additionally, active and intelligent film could monitor the spoilage of rich protein foods in response to pH change. Therefore, this film could monitor the sensory acceptance, and extending the shelf life of rich protein foods simultaneously. In this paper, the structure and functional properties of anthocyanins, the composite actions of anthocyanin extracts and biomass materials, and their reinforced properties of active and intelligent film were discussed. Also, the applications of this film in quality maintenance, shelf-life extension and quality monitoring for fresh meat, aquatic product and milk were summarized. The film that achieves high stability and continuous release of anthocyanins on demand will become an underlying trend in packaging applications for rich protein foods.

Background: Diffuse large B-cell lymphoma is the most common type of non-Hodgkin's lymphoma. Due to the variety of clinical manifestations, accurate diagnosis can be challenging. Here, we present a case of DLBCL that was initially misdiagnosed as a hematoma, highlighting the importance of considering malignancy in the setting of non-responsive soft tissue swelling. Methods: A 76-year-old man presented to the emergency department with right periorbital swelling and ecchymosis. The symptoms first appeared after an injury and did not resolve spontaneously. The patient was taking warfarin for atrial fibrillation. A facial bone CT revealed a large irregular homogeneous mass. An extraconal hematoma was suspected based on clinical history and radiologic findings. Incision and drainage were performed, resulting in evacuation of old blood. Despite continued drainage, the patient's symptoms worsened. A comparison with the previous CT revealed an increase in the size of the lesion. As a result, a surgical excisional biopsy was performed. Results: Biopsy of the mass showed a diffuse infiltrate of lymphocytes around the tissue. The diagnosis of diffuse large B-cell lymphoma was confirmed pathologically. The patient was referred to hematology for further management. Conclusions: DLBCL is a rare disease associated with a poor prognosis. Due to the previous injury and the use of anticoagulants, the patient was initially misdiagnosed as having a hematoma. This delayed the prompt diagnosis and affected the timing of treatment initiation. We must be aware that a malignant mass is a potential cause of unresponsive soft tissue swelling.

Fragment-based drug discovery (FBDD) has become a major strategy to derive novel lead candidates for various therapeutic targets, as it promises efficient exploration of chemical space by employing fragment-sized (MW < 300) compounds. One of the first challenges in implementing a FBDD approach is the design of a fragment library, and more specifically, the choice of its size and individual members. A diverse set of fragments is required to maximise the chances of discovering novel hit compounds. However, the exact diversity of a certain collection of fragments remains underdefined, which hinders direct comparisons among different selections of fragments. Based on structural fingerprints, we herein introduced quantitative metrics for the structural diversity of fragment libraries. Structures of commercially available fragments were retrieved from the ZINC database, from which libraries with sizes ranging from 100 to 100,000 compounds were selected. The selected libraries were evaluated and compared quantitatively, resulting in interesting size-diversity relationships. Our results demonstrated that while library size does matter for its diversity, there exists an optimal size for structural diversity. It is also suggested that such quantitative measures can guide the design of diverse fragment libraries under different circumstances.

The move to a low carbon economy is very important for enhancing international competitiveness. The eco-innovation is the critical factor of the green paradigm. This study is designed to investigate deeply the determinants of eco-innovation of manufacturing firms in Korea by suggesting anticipated regulations, self-regulations, and industry-specific characteristics as external factors and open information sources as internal factors. The data used in the analysis is 1946 sample firms from Korean Innovation Survey 2010 based on the Oslo Manual. Using the multi-variate probit analysis and the zero-inflated negative binomial (ZINB) regression analysis, we have found out that the anticipated regulations and self-regulations have significant influences both on eco-process innovation and eco-product innovation, while industrial characteristics have no effects. The empirical results also show that the breadth of information sources has a positive effect on businesses in implementing eco-innovations. Our findings show that the Korean government should provide a good platform where firms can better understand the future trends of environmental policies, particularly policies on anticipated and self-regulations. At the same time, Korean firms should establish a voluntary system to control environmental activities so that they can improve eco-innovations through integrating external information.

Recently L-shaped tunneling field-effect-transistor (LTFET) has been introduced to overcome the thermal subthreshold limit of conventional metal-oxide-semiconductor field-effect-transistors (MOSFET). In this work, shortcoming of LTFET was investigated. It was found that corner effect present in LTFET effectively degrades its subthreshold slope. To get rid of corner effect a new type of device with dual material gates is presented. The new device termed as DG-LTFET gets rid of the corner effect and results in a significantly improved subthreshold slope of less than 10 mV/dec, and an improved ON/OFF current ratio over LTFET. In this work DG-LTFET was evaluated for different device parameters, and bench-marked against LTFET. This work presents an optimum configuration of DG-LTFET in terms of device dimensions and doping levels, to get the best subthreshold, ON current and ambipolar performance from the DG-LTFET.

Although health policy resides mainly with the government, industry can play an important role in building a health ecosystem. From March to May, we administered questionnaires to 1,200 individuals from the general Korean population asking about their perception of health-friendly labels, and if they would purchase such labeled products (foods, pharmaceuticals, etc.) and services (purifying water, preventing air pollution, etc.) at extra cost. The participants placed a high value on the importance of mental, social, spiritual, and physical health factors in terms of company’s products and services with a score of about 8 out of 10 (range, 7.74-8.33). Most respondents (72.4%) said they were interested in adopting health-friendly labels. When a health-friendly label is introduced (such as one by the Business for Social Responsiveness), 65.1% of the respondents said they intended to purchase the product or service, while 6.8% said they did not, and 75.0% said they were willing to pay extra for the health-friendly product or service. Multivariate logistic regression models showed urban residence, high education level, and good social health to be significantly associated with positive attitudes toward health-friendly labels. People with high income, no religion, or normal weight were more likely to say they intend to purchase products and services with health-friendly labels. They also had a more positive attitude toward paying more for such products and services, as did people with good spiritual health. This study provides data that illustrate the importance of health-friendly products and services to the general population and companies.

Background and Objectives: The ingestion of anhydrous calcium chloride (CaCl2) causes direct injury to the gastrointestinal wall via a thermal burn. Severe CaCl2 intoxication can induce a hypercalcemic crisis, presenting with arrhythmia, acute pancreatitis, and acute kidney injury. This case report details a patient with hematemesis and hypercalcemia following the ingestion of a commercial desiccant. We aimed to report the progression of the case and focused on the elec-trocardiographic manifestations. Case presentation: A 39-year-old female presented at a regional emergency center with blood in her vomit after the ingestion of a commercial desiccant. Bloody emesis was the initial symptom, and various electrolyte imbalances developed during admission. Electrocardiogram (ECG) changes occurred early after hospitalization and disappeared before the electrolyte levels normalized. The patient was maintained in an NPO state throughout her hospital stay. Bloody emesis and abdominal pain resolved rather early, despite her minimal mention of symptoms, possibly due to her suspected negative psychiatric symptoms. Conclusions: The rise in suicidal attempts has led to an increase in unusual intoxication cases. Previous reports on CaCl2 ingestion primarily considered the gastrointestinal injury. In this case, we observed the dynamic and prolonged multiple electrolyte imbalances along with the early-phase ECG changes, all of which responded well to supportive care. This report adds to the understanding of the diverse manifestations and management of CaCl2 intoxication.

In the last two decades, our knowledge of synaptic proteomes and their relationship to normal brain function and neuropsychiatric disorders has been expanding rapidly through the use of more powerful neuroproteomic approaches. However, mass spectrometry (MS) based neuroproteomic studies of synapses still need cell-type, spatial, and temporal proteome information. With the advancement of sample preparation and MS techniques, we have just begun to identify and understand proteomes within a given cell type, subcellular compartment, and cell-type-specific synapse. Here, we review the progress and limitations of MS-based neuroproteomics of synapses in the mammalian CNS and highlight the recent applications of these approaches in studying neuropsychiatric disorders such as major depressive disorder and substance use disorders. Combining neuroproteomic findings with other omics studies can generate an in-depth, comprehensive map of synaptic proteomes and possibly identify new therapeutic targets and biomarkers of several central nervous system disorders.

Aluminum alloy (Al6061) sheet micro-hole processing is extensively used in smartphones, tablet PC, and smart wearable devices. The micro-hole processing is commonly performed using laser, micro drilling, microstamping, micro discharge, and chemical etching technologies. Micro-stamping technology is characterized by precision and rapid processing, but the precision positioning of the punch head and lower die is one of the major difficulties in micro-hole stamping, especially in manufacturing array micro-holes. This study used stamping without die technology. This technology uses an array punch head to punch the lower die holes on the base, then performs array micro-hole stamping. The experimental results show that a micro-hole array with 37 micro-holes were successfully manufactured and can be reproduced many times. Tapered array micro-holes with a high aspect ratio can be manufactured using this stamping without die technology; the micro-hole depth can be 260μm, the inlet diameter is 116μm, and the outlet diameter is 25μm. This study has successfully developed the feasibility of array micro-hole stamping technology.

Teachers of English as a foreign language in Taiwan are challenged to organize multi-dimensional language activities for foreign students coming from ASEAN countries, including Japan, the Philippines, South Korea, and Vietnam. With different cultural backgrounds, these students have different prior knowledge of Taiwanese culture, and, because of the similarities and differences between Taiwan and these countries, it is meaningful to explore the development of globalization with the students, who are learning both English and Chinese. The different historical backgrounds, various cultural and religious differences, and social conditions, such as gender relationships in working places, are significant topics for class discussions. When teachers serve as discussion facilitators, they encourage students to express their own multi-identities and expectations for the exchange program. Most interesting of all is to find out about their own short-term and long-term career goals. 32 foreign students from the Philippines and Vietnam were recruited for research. Questionnaires were used to assess their foreign language learning motivation and strategies, as well as to discover the learning environment they prefer and their globalization prospects. It was found that multi-lingual language policies for promoting globalization in higher education are very likely to influence the success of foreign student study in Taiwan.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

As symbionts of fungi and algae, lichens produce a variety of secondary products which pharmacological activities. This study aimed to investigate the anti-inflammatory activities of Heterodermia hypoleuca and its main compound, atraric acid. The results confirmed that atraric acid could regulating induced pro-inflammatory cytokine, nitric oxide, induced nitric oxide synthase and cyclooxygenase-2 expression by lipopolysaccharide (LPS)-stimulated RAW264.7 cells. Means while, atraric acid down-regulated expression of phosphorylated IκB, ERK and nuclear factor kappa B (NFκB) signaling pathway to exhibit anti-inflammatory effects in LPS-stimulated RAW264.7 cells. Based on these results, the anti-inflammatory effect of atraric acid during LPS-induced endotoxin shock in a mouse model was confirmed. In the atraric acid treated-group, cytokine production was decreased in the peritoneum and serum, and each organ damaged by LPS-stimulation was recovered. These results show that atraric acid has an anti-inflammatory effect and its molecular mechanism may be involved in the inactivation of the ERK/NFκB signaling pathway, demonstrating its value as a potential therapeutic for inflammatory diseases.

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

Intelligent ship technology is currently an international research hotspot, and model predictive control is widely used in the path-tracking control of intelligent vehicles. To construct an intelligent ship anti-disturbance path-tracking control method, firstly, an environmental disturbance model was constructed with the actual meteorological data of the target sea area. Secondly, the Fossen ship equation of motion is linearized and discretized as the ship motion model. Thirdly, the expression of the prediction equation is derived from the ship motion model. Fourthly, the cost function is constructed by using the polar diameter and polar angle values of the ship. Fifth, the power function in the cost function is replaced with an exponential function to obtain an improved cost function. Sixthly, according to the Lyapunov theory and the MPC terminal constraint theory, the stability of the improved cost function is verified. Seventh, different test paths are set up, the environmental disturbance model is taken as the external disturbance, the ship motion model, the prediction equation, and the improved cost function are used to design the anti-disturbance path-tracking control algorithm according to the model prediction control idea for simulation experiments. Finally, different MATLAB simulation results show that the improved cost function can resist disturbance of the external wave, current, and wind, and effectively track the target path. Therefore, this study provides a reference for improving the navigation safety of ship path-tracking.

Magnetometric Resistivity(MMR) Method, which can use the power supply method of the traditional apparent resistivity method to measure the magnetic field. At present, the application research abroad is relatively extensive, but the domestic(China) research on the application of the MMR method is very few, and it is not even well-known. This paper is based on the MMR theoretical method under the point source DC condition, combined with the abnormal potential method and the modified Biot-Savart law, and using the three-dimensional numerical calculation method of the finite difference method to calculate the abnormal potential field, electric field, and magnetic field on the matlab2018a platform. Calculate, realize the multi-physics simulation in the electromagnetic field through Matlab platform programming, and verify the correctness of the algorithm by the spherical anomaly model with an analytical solution. Through the visual simulation of the three-dimensional data volume of the multi-physics field in the electromagnetic field, we can better understand the response mechanism of the electromagnetic field under DC conditions and grasp their three-dimensional spatial distribution rules. It is hoped that the research in this article can help the research of MMR Personnel better use this method for exploration.

With the rapid development of network science, Turing pattern on complex networks has attracted extensive attention from researchers. In this paper, we focus on spatial patterns in multiplex ER (Erdös-Rényi) random networks, taking the predator-prey model with Allee effect and hyperbolic mortality as an example. In theory, the threshold condition for generating Turing pattern is given using the Turing instability theory of multiplex networks. Numerically, we design relevant experiments to explore the impact of network topology on Turing pattern. The factors considered include model parameters, diffusion rate, average degree of the network, and differences in the average degree of different layers. The results indicate that the importance of diffusion rate and network average degree for Turing pattern is affirmed on the single-layer network. For multiplex networks, the differentiation of average degrees in different layers controls the generation of Turing pattern, which is not affected by the diffusion rates of the two populations. More interestingly, we observe the switching of Turing pattern and spatiotemporal pattern. We believe that these findings contribute to a better understanding of self-organization on complex networks.

To address the issue of reduced orbit estimation accuracy resulting from discrepancies between in-orbit measured geomagnetic field values and IGRF model values in autonomous orbit estimation of microsatellites based on geomagnetic field measurements, this study introduces an adaptive cubature H-infinity filtering algorithm. Firstly, it presents the low-altitude orbital dynamics model and geomagnetic field measurement model for microsatellites. Subsequently, within the adaptive cubature H-infinity filtering algorithm, a spherical simplex rule and a second-order Gaussian-Legendre quadrature criterion are employed to compute the spherical surface integral and radial integral. Additionally, a spherical simplex-radial quadrature rule is proposed to enhance the approximation accuracy of nonlinear Gaussian weighted integrals. Furthermore, by integrating extended H-infinity filtering based on game theory with the cubature quadrature rule, an inverse proportional relationship between constraint level and filtering innovation is established. This allows for adaptive adjustment of the constraint level to enhance robustness against model errors. Finally, through semi-physical simulation experiments, it is demonstrated that compared with traditional algorithms, the proposed algorithm improves autonomous orbit estimation position accuracy of microsatellites by 7.49%, while also enhancing velocity accuracy by 3.1%, thus validating its effectiveness.

Our previous studies showed pure blue (B) spectra from LEDs can promote shade avoidance responses (SARs). However, it is unknown whether SARs vary among different peak wavelengths (λpeak) of B or how they compare with other photomorphologically-important wavebands, such as ultraviolet-A and far-red. To answer these questions, mustard (Brassica juncea, ‘Ruby Streaks’) and arugula (Brassica eruca, ‘Rocket’) seedlings, grown to the cotyledon unfolding stage under the following narrowband spectrum treatments: UVA (λpeak = 385 nm), B1 (λpeak = 404 nm), B2 (λpeak = 440 nm), B3 (λpeak = 455 nm), and FR (λpeak = 730 nm). Both red (R, λpeak = 660 nm) and dark (D) were used as control treatments. The spectrum treatments were provided at 50 μmol m−2 s−1 on a continuous basis. There were no differences among the B treatments except for reduced mustard fresh weight (FWt) in B3. Compared with R, the B treatments promoted hypocotyl elongation, reduced cotyledon size, and increased petiole length in arugula and B1 increased petiole length in mustard. Compared with the B treatments, UVA inhibited hypocotyl and petiole elongation, similar to or greater than R in both species. Compared with the other LED treatments, seedlings grown under FR generally had the lowest hypocotyl and petiole elongation and the smallest cotyledons. Compared to the LED treatments, D substantially promoted hypocotyl elongation and reduced cotyledon size, except compared to FR in arugula. Among the spectrum treatments, the three B treatments had the greatest SAR promotion effects in both species. Despite having the lowest phytochrome activity, FR inhibited SARs normally associated with high FR environments. Legacy parameters used to estimate SAR-promoting effects of spectrum treatments may not be appropriate for characterizing narrowband spectra from LEDs – new approaches must be developed.

Polymethyl methacrylate (PMMA) polymer is widely used in various fields today. In order to thoroughly reveal the structural impact performance of PMMA materials, this paper is based on the comprehensive Johnson-Cook constitutive model and damage failure model, and accurately confirm the J-C constitutive and damage failure model parameters of PMMA through material test data, The dynamic process of steel bullet impacting PMMA plate structure is analyzed by finite element software ABAQUS. The calculation results show that the numerical simulation results in this paper are in good agreement with the experimental test data. Therefore, the feasibility and accuracy of the impact analysis of PMMA structures based on J-C constitutive and damage failure models in this paper are studied. Finally, based on the J-C constitutive model and damage failure model, the variation of the residual velocity of the bullet with the PMMA plate thickness is analyzed in depth, that is, the results show that the residual velocity of the bullet has a certain linear relationship with the plate thickness.

Sign language recognition is essential in hearing-impaired people’s communication. Sign language recognition is an important concern in computer vision and has been developed with rapid progress in image recognition technology. However, sign language recognition using a general monocular camera has problems with occlusion and recognition accuracy in sign language recognition. In this research, we aim to improve accuracy by using a 2-axis bending sensor as an aid in addition to image recognition. We aim to achieve higher recognition accuracy by acquiring hand keypoint information of sign language actions captured by a monocular RGB camera and adding sensor assist. To improve sign language recognition, we need to propose new AI models. In addition, the amount of dataset is small because it uses the original data set of our laboratory. To learn using sensor data and image data, we used MediaPipe, CNN, and BiLSTM to perform sign language recognition. MediaPipe is a method for estimating the skeleton of the hand and face provided by Google. In addition, CNN is a method that can learn spatial information, and BiLSTM can learn time series data. Combining the CNN and BiLSTM methods yields higher recognition accuracy. We will use these techniques to learn hand skeletal information and sensor data. Additionally, the 2-axis Bending sensor glove data support training AI model. Using these methods, we aim to improve the recognition accuracy of sign language recognition by combining sensor data and hand skeleton data. Our method performed better than using skeletal information, achieving 96.5% accuracy in Top-1.

Land use is an embodiment of human socioeconomic activities and represents a bridge between these activities and natural systems. Through social activities, humans transform land use to promote social and economic development and improve production, living conditions, and eco-logical functions of land. Rural residential land represents a space for rural residents to reside in and exhibits spatial characteristics that evolve over time, which is proof of rural socioeconomic development. This paper observes rural residential land in 21 cities on the Grand Canal and analyses its spatial differentiation. Then, it explores the driving factors of this land using spatial grid analysis and the geographic detector model. Lastly, it proposes three different forms of rural residential land based on the results. The study found that: (1) the change of rural residential land in the northern part of the Grand Canal was more volatile than that in the southern part. The change of rural residential land from 1990 to 2020 conformed to the pattern of cultivated land - rural residential land - urban construction land; (2) Based on the driving factors of rural residen-tial land, the land is divided into one-dimensional cities, two-dimensional cities and three-dimensional cities. Circular, linear, and scattered cities of different sizes were affected by socioeconomic factors, transportation accessibility, and the natural environment, respectively; and (3) Finally, according to the spatial differentiation characteristics and the driving factors of rural residential land, the study proposes the construction of three types of villages through the strate-gies of constructing large-scale villages, relocating and reconstructing new villages, and con-structing high-quality villages, respectively. Enhancing the scientific planning of rural residential land and its efficiency can offer the protection of agricultural land and the integration of urban and rural areas in the new era.

Failure characteristics induced by unloading disturbance and the corresponding mechanical mechanism of the coal seam floor are important theoretical bases for water-bursting prevention from the floor of the coal seam and rock burst alarm in deep mining. However, the existing two-dimensional ground-pressure-control theory based on shallow mining cannot sufficiently guide deep-mining practices. In this study, the redistribution of mining-induced stress field in rocks surrounding the longwall face and mechanical behaviors of strata in deep mining are investigated through a combination of numerical simulation, physical simulation, and field measurement. Results demonstrate that mining-induced stress fields in the floor of the longwall face differ in space and time. Vertical stress unloading from top to bottom of the floor and horizontal stress unloading are relatively low. A concentration zone of high horizontal stress exists at stope boundaries. The critical yield load of rock stratum in the floor is determined through thin plate yield theory. Under the combined effect of concentrated high horizontal and vertical resilience stresses, strata in the floor fracture from seam to seam if the load increases to the minimum critical buckling value. Fractured strata slide along the fracture surface, which leads to floor heave. The stope floor shows evident time-delay progressive failure characteristics. The stress shell in the stope floor in deep mining is found to be a sensitive mechanical parameter that produces three-dimensional ground-pressure behavior in the floor. This ground-pressure behavior in the stope floor is controlled by the existence of the corresponding stress shell and effects induced by its space–time evolution. This study provides theoretical basis for the dynamic control of a hazard-inducing environment in engineering and minimizing or altering disaster-occurrence conditions during the construction engineering of the coal seam floor.

Landslides impact on human activities and socio-economic development especially in mountainous areas. This study focuses on the comparison of the prediction capability of advanced machine learning techniques for rainfall-induced shallow landslide susceptibility of Deokjeokri catchment and Karisanri catchment in South Korea. The influencing factors for landslides i.e. topographic, hydrologic, soil, forest, and geologic factors are prepared from various sources based on availability and a multicollinearity test is also performed to select relevant causative factors. The landslide inventory maps of both catchments are obtained from historical information, aerial photographs and performing field survey. In this study, Deokjeokri catchment is considered as a training area and Karisanri catchment as a testing area. The landslide inventories content 748 landslide points in training and 219 points in testing areas. Three landslide susceptibility maps using machine learning models i.e. Random Forest (RF), Extreme Gradient Boosting (XGBoost) and Deep Neural Network (DNN) are prepared and compared. The outcomes of the analyses are validated using the landslide inventory data. A receiver operating characteristic curve (ROC) method is used to verify the results of the models. The results of this study show that the training accuracy of RF is 0.757 and the testing accuracy is 0.74. Similarly, training accuracy of XGBoost is 0.756 and testing accuracy is 0.703. The prediction of DNN revealed acceptable agreement between susceptibility map and the existing landslides with training and testing accuracy of 0.855 and 0.802, respectively. The results showed that, the DNN model achieved lower prediction error and higher accuracy results than other models for shallow landslide modeling in the study area

Complex models have received significant interest in recent years and are being increasingly used to explain the stochastic phenomenon with upward and downward fluctuation such as the stock market. Different from existing semi-variance methods in traditional integer dimension construction for two variables, this paper proposes a simplified multi-factorized fractional dimension derivation with the exact Excel tool algorithm involving the fractional center moment extension to covariance, which is a complex parameter average that is a multi-factorized extension to Pearson covariance. By examining the peaks and troughs of gold price averages, the proposed algorithm provides more insight into revealing underlying stock market trends to see who is the financial market leader during good economic times. The calculation results demonstrate that the complex covariance is able to distinguish subtle differences among stock market performances and gold prices for the same field that the two variable covariance may overlook. We take the London, Tokyo, Shanghai, Toronto and Nasdaq as the representative examples.

Intergenerational integration has given rise to a novel aging paradigm known as all-age communities, which is garnering international attention. In China, the aging population and the implementation of the three-child policy have resulted in increased demand for retirement and childcare services among residents in older neighborhoods. Consequently, there is a pressing need to retrofit these older neighborhoods to accommodate all-age living arrangements given the high demand they generate. Therefore, this study undertakes research interviews with residents and constructs an exploratory theoretical model rooted in established theory. To assess the significance of our model, we employ Smart PLS 3.0 based on 297 empirical data points. Our findings indicate that anxiety has a significant negative effect on payment behavior; objective perception, willingness to pay, and government assistance exert significant positive effects on payment behavior. By comprehensively analyzing the mechanisms underlying residents’ payment behavior, this study provides valuable insights to the government for promoting the aging process within communities and formulating effective transformation policies.

Today, the digital economy has pursued the required social and economic development, and enterprises can achieve long-term sustainability by relying on the digital platform ecosystem. However, the development of the digital economy and the rapid growth of platform ecosystems have also generated some problems. To study effective digital platform ecosystem governance, this study used the tripartite evolutionary game method and analyzed the changes and effects of platform regulation under different development stages from the perspectives of government, platforms, and enterprises. The results indicate that in the early stages, digital platforms primarily relied on the government’s obligation to regulate. With the digital platform ecosystem’s evolution, the platform organization and settled enterprises’ governance effects gradually appeared, establishing the three common constraints of governance mode. Finally, when the digital platform ecosystem is in its self-renewal period, the government effect is reduced, with the platform itself and settled enterprises taking primary supervisory roles. This study provides reasonable methods for effective platform governance at different stages and enriches the theoretical basis and management practices of platform ecosystems.

Existing one-shot neural architecture search (NAS) methods have to conduct a search over a giant super-net, which leads to the huge computational cost. To reduce such cost, in this paper, we propose a method, called FTSO, to divide the whole architecture search into two sub-steps. Specifically, in the first step, we only search for the topology, and in the second step, we search for the operators. FTSO not only reduces NAS’s search time from days to 0.68 seconds, but also significantly improves the found architecture's accuracy. Our extensive experiments on ImageNet show that within 18 seconds, FTSO can achieve a 76.4% testing accuracy, 1.5% higher than the SOTA, PC-DARTS. In addition, FTSO can reach a 97.77% testing accuracy, 0.27% higher than the SOTA, with nearly 100% (99.8%) search time saved, when searching on CIFAR10.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

As the number of end-of-life vehicles continues to grow, the field of separation technology for broken copper and aluminium parts of end-of-life vehicles has emerged as a significant area of research. As a key technology for the separation of non-magnetic non-ferrous metals, such as copper and aluminium, eddy current separation can achieve efficient separation of non-magnetic non-ferrous metals according to their differing conductivity and density. Nevertheless, further research is required in the separation of large-scale broken copper and aluminium parts of end-of-life vehicles. This paper presents a novel magnetic roller model comprising circumferential and axial periodic arrangements of permanent magnets. A single permanent magnet was constructed as an equivalent current model, and the magnetic scalar potential equations were solved using simulation tools. This allowed the distribution of the magnetic field outside the magnetic roller to be studied. The results demonstrate that the novel permanent magnet array magnetic roller can enhance the magnetic field intensity and action distance of the external magnetic field, which is more conducive to the separation of large-scale broken copper and aluminium parts of scrap cars. The findings of this research provide a theoretical foundation for the separation of scrap car broken copper and aluminium parts.

This study examined ways to prevent failures in the front-end of forklifts by addressing the center of gravity of heavy objects carried by forklifts, predicting the remaining useful lifetime (RUL), and the fault diagnosis based on alarm rules. In the research process, acceleration signals were acquired from the outer beam of the front-end of the forklift. A one-second window was applied to extract the time-domain statistical features, which were then set as variables. An exponentially weighted moving average was used to smooth the noise in the feature data set. The AWGN and LSTM autoencoders were used for data augmentation. Based on them, random forest and lightGBM models were used to develop classification models for the weight center of heavy objects carried by a forklift. In addition, contextual diagnosis performed by applying exponentially weighted moving averages to the classification probabilities of the machine learning models showed that random forest achieved an accuracy of 0.9563 and lightGBM achieved an accuracy of 0.9566. In addition, the acceleration data were collected through experiments to predict forklift failure and RUL because of the repeated forklift use when the center of heavy objects carried by the forklift was skewed to the right. The time-domain statistical features of the acceleration signals were extracted and set as variables by applying a 20-second window. Subsequently, logistic regression and random forest models were used to classify the failure stages of the forklifts. The f1-score (macro) obtained were 0.9790 and 0.9220 for logistic regression and random forest, respectively. In addition, the random forest probabilities for each stage were combined and averaged to generate a degradation curve and derive the failure threshold. The coefficient of the exponential function was calculated using the least squares method on the degradation curve, and the RUL prediction model was developed to predict the failure point. In addition, the SHAP algorithm was used to identify the significant features in classifying the stage. The alarm rule-based fault diagnosis was performed using the threshold of the normal stage distribution of the significant features.

Background: We conducted research on the newly developed personalized recommendation service (PRS) of the global network of Korean scientists and engineers (KOSEN) in order to explore the information usage behavior and importance of the PRS used by Korean scientists and engineers. Methods: In order to understand information usage behavior, we gathered data from 513 survey results and analyzed them in terms of information usage behavior and the corresponding importance in each of the service quality areas. Results: We analyzed the 321 outcomes that indicated non-use of the PRS in order to understand the underlying reason(s); we employed 192 results that demonstrated the use of functionality to examine information usage behavior and importance. They found that the predominant motive for non-use of the service resulted from the respondents not knowing how to use it. According to demographic characteristics, the usage behavior of the PRS showed a difference regarding the purpose of using the service in the categories of gender and major field of study. Furthermore, users were concerned with various components of the PRS such as ease of use, design, relevance of content, user support, and interactivity. Conclusions: We suggest reinforcing user education degree and promotion to enhance the PRS. Since users were concerned with ease of use, design, relevance, user support, and interactivity, we recommend these as major points for improvement.

Proton exchange membrane water electrolyzers (PEMWEs) for water electrolysis have received tremendous attention due to their immediate response, high proton conductivity, low ohmic losses and gas crossover rate. However, design high activity, economical and long-term durable electrocatalysts in an acidic environment is still the bottleneck to realize the large-scale commercialization of PEMWEs. Iridium-based materials represent one of the most promising classes of oxygen evolution reaction (OER) catalysts due to their intrinsic stability in acid media over ruthenium-based counterparts. However, only a few innovative approaches have been developed to synthesizing iridium-based catalysts (IBCs) in the past decade, mainly due to achieving high activity may deteriorate the stability of IBCs. Accordingly, various engineering strategies of optimizing IBCs have been proposed to address this issue, including doping engineering, morphology engineering, crystal phase engineering and support engineering. Herein, a critical overview focusing on various synthesis and modulation strategies of IBCs is presented, based on an in-depth understanding of the relationship between electronic structures, charge redistribution and activity as well as stability of the electrocatalysts. In addition, the unprecedented achievements in PEMWEs are summarized. The reaction mechanisms and future perspectives are critically discussed to inspire more rational design of IBCs toward practical applications.

Deep underground laboratories offer advantages for conducting high-precision observations of weak geophysical signals, benefitting from a low background noise level. It is both valuable and feasible to enhance strong, noisy ground electromagnetic (EM) field data using synchronously recorded underground EM signals, which typically exhibit a high signal-to-noise ratio. In this study, we propose an EM field reconstruction method employing a Long Short-Term Memory (LSTM) recurrent neural network with referenced deep underground EM observations. Initially, a deep learning model was developed to capture the time-varying features of underground multi-component EM fields using the LSTM recurrent neural network. Subsequently, this model was applied to process synchronously observed strong, noisy data from other conventional observation systems, such as those at surface, to achieve noise suppression through signal reconstructions. Both theoretical analysis and practical observational data suggest that the proposed method effectively suppresses noise and reconstructs clean EM signals. This method is efficient and time-saving, representing an effective approach to fully utilizing the advantages of deep underground observation data. Furthermore, this method could be extended to the processing and analysis of other geophysical data.

The way people innovate and create new ideas and bring them to the market is undergoing a fundamental change from closed innovation to open innovation. Why and how do firms perform open innovation? Firms’ open innovation is measured through the levels of firms’ joint patent applications. Next, we analyze network structures and characters of firms’ joint patent applications such as betweenness and degree centrality, structure hole, and closure. From this research, we drew conclusions as follows. First, the structure of collaboration networks has both direct and indirect effects on firms’ innovative performance. Second, in the process of joint patent applications, there is a long tail phenomenon in networks of joint patent applications. Third, the number of patents and International Patent Classification (IPC) subclasses together constitute a meaningful measure of the innovation performance of firms.