The development of sensitive and specific exosome detection devices is highly desirable because it is believed to deliver specific important information for cancer screening, diagnosis, and monitoring. Among many detection techniques, nanoplasmonic sensors are optical detection methods that offer advantages in sensitivity and detection speed and this makes the sample analysis process faster and more accurate. This paper summarizes the development of nanoplasmonic biosensors, especially Surface Plasmon Resonance (SPR) and Localized Surface Plasmon Resonance (LSPR)-based biosensors for exosome detection. There are three main parts in this paper. The first part will focus on introducing the theoretical background regarding the working principles of SPR and LSPR biosensors. After that, we will introduce several methods that can be used for exosome isolation. This article will close by explaining the engineering of nanoplasmonic sensors both in terms of transducer modification to amplify the signal and functionalization strategies to increase sensor specificity. In this section, the detection mechanism, the type of exosomes detected, and the resulting detection limits are some of the points highlighted in this paper.

Manipulation of radiation pattern control is challenging, especially at low frequencies. In this paper, we demonstrate that acoustic metamaterials as an effective array of quadrupoles can remarkably improve the directionality of acoustic radiation at low frequencies, compared with previous metamaterials as monopole and dipole structures. The directivity of the acoustic radiation can be adjusted by changing the characteristic parameter and the symmetry of the structure, which provide a flexible method of adjustable radiation di-rections. The directionality can be further improved by constructing linear array of structure. Our work opens an approach of acoustic radiation control via quadrupolar metamaterials.

Objectives To examine the comorbidity burden in patients with rheumatoid arthritis (RA) patients using a nationwide population-based cohort by assessing the Charlson Comorbidity Index (CCI), Elixhauser Comorbidity Index (ECI), Multimorbidity Index (MMI), and Rheumatic Disease Comorbidity Index (RDCI) scores and to investigate their predictive ability for all-cause mortality. Methods We identified 24,767 RA patients diagnosed between 1998–2008 in Taiwan and followed up until December 31, 2013. The incidence of comorbidities was estimated in three periods (before, during, and after the diagnostic period). The incidence rate ratios were calculated by comparing during vs. before and after vs. before the diagnostic period. One- and 5-year mortality rates were calculated and discriminated by low and high-score groups and modified models for each index. Results The mean score at diagnosis is 0.8 in CCI, 2.8 in ECI, 0.7 in MMI, and 1.3 in RDCI, and annual percentage changes are 11.0%, 11.3%, 9.7%, and 6.8%, respectively. The incidence of any increase in the comorbidity index is significantly higher in the periods of ‘during’ and ‘after’ the RA diagnosis (incidence rate ratios for different indexes: 1.33-2.77). The mortality rate significantly differs between the high and low-score groups measured by each index (adjusted hazard ratios: 2.5-4.3 for different indexes). CCI is slightly better in the prediction of 1- and 5-year mortality rates. Conclusion Comorbidities are common before and after RA diagnosis, and the rate of accumulation accelerates after RA diagnosis. All four comorbidity indexes are useful to measure the temporal changes and to predict mortality.

We aimed to determine whether A-mode ultrasound (US) can provide accurate and reliable measurements comparable to those obtained through B-mode US, under diverse conditions. Thirty healthy participants (15 female, 15 male) underwent measurements of subcutaneous fat thickness (SFT), muscle thickness (MT), and muscle quality (MQ) in the trapezius and biceps brachii muscle with both US modes after and before exercises designed to stimulate the respec-tive muscles. In three key indices, the results demonstrated high validity of A-mode, with min-imal mean differences between the two devices less than 0.91mm and intraclass correlation coef-ficients exceeding 0.95 at all measures. Also, Correlation coefficients between error scores and average scores for the trapezius and biceps brachii muscles suggested no evidence of systematic error. The trapezius MT and MQ significantly increased, and biceps brachii MT significantly in-creased after exercise (p<0.05). Notably, both A-mode and B-mode exhibited the same tendency in these post-exercise changes in muscle. This study suggests that low-cost and low-resolution A-mode US provides measurements of SFT, MT, and MQ similar to more expensive, high-resolution B-mode imaging. A-mode US can serve as an affordable and portable alternative for muscle assessment.

The Homotopy Analysis Method (HAM) is a useful method to derive analytical approximate solutions of black holes in modified gravity theories. In this paper, we study the Einstein-Weyl gravity coupled with Maxwell field, and obtain analytical approximation solutions for charged black holes by using the HAM. It is found that the analytical approximate solutions are sufficiently accurate in the entire spacetime outside the black hole's event horizon, and also consistent with numerical ones for charged black holes in the Einstein-Maxwell-Weyl gravity.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

The aim of this study is to prepare redox-sensitive nanophotosensitizers for targeted delivery of chlorin e6 (Ce6) against cervical cancer. For this purpose, Ce6 was conjugated with β-cyclodextrin (bCD) via disulfide bond creating nanophotosensitizers that were fabricated for redox-sensitive delivery of Ce6 against cancer cells. bCD was treated with succinic anhydride to synthesize suc-cinylated bCD (bCDsu). After that, cystamine was attached to the carboxylic end of bCDsu (bCDsu-ss) and the amine end group of bCDsu-ss was conjugated with Ce6 (bCDsu-ss-Ce6). Chemical composition of bCDsu-ss-Ce6 was confirmed with 1H and 13C NMR spectra. bCDsu-ss-Ce6 nanophotosensitizers were fabricated by dialysis procedure. They formed small particles with an average particle size of 152.0±23.2 nm and they showed improved singlet oxygen (SO) generation in the aqueous solution under light irradiation and was significantly higher than that of Ce6 alone. Ce6 release rate from bCDsu-ss-Ce6 nanophotosensitizers was accelerated by addition of glutathione (GSH), indicating that bCDsu-ss-Ce6 nanophotosensitizers have re-dox-sensitive photosensitizer delivery capacity. bCDsu-ss-Ce6 nanophotosensitizers have low in-trinsic cytotoxicity against CCD986Sk human skin fibroblast cells as well as Ce6 alone. However, bCDsu-ss-Ce6 nanophotosensitizers showed improved Ce6 uptake ratio, higher reactive oxygen species (ROS) production and phototoxicity compared to those of Ce6 alone. GSH addition resulted in higher Ce6 uptake ratio, ROS generation and phototoxicity than those of Ce6 alone, indicating that bCDsu-ss-Ce6 nanophotosensitizers have redox-sensitive biological activity in vitro against HeLa human cervical cancer cells. At tumor xenograft model using HeLa cells, bCDsu-ss-Ce6 nanophotosensitizers efficiently accumulated in the tumor rather than normal organs, i.e. fluores-cence intensity in tumor tissues was significantly higher than those of other organs while Ce6 alone did not specifically target tumor tissue. These results indicated higher anticancer activity of bCDsu-ss-Ce6 nanophotosensitizers, by efficiently inhibiting growth of tumor in in vivo animal tumor xenograft study.

Static standing postural stability has been measured by multiscale entropy (MSE), which is used to measure complexity. In this study, we used the average entropy (AE) to measure the static standing postural stability, as AE is a good measure of disorder. The center of pressure (COP) trajectories were collected from 11 subjects under four kinds of balance situation, from stable to unstable: bipedal with open eyes, bipedal with closed eyes, unipedal with open eyes, and unipedal with closed eyes. The AE, entropy of entropy (EoE), and MSE methods were used to analyze these COP data, and EoE was found to be a good measure of complexity. The AE of the 11 subjects sequentially increased by 100%as the balance situations progressed from stable to unstable, but the results of EoE and MSE did not follow this trend. Therefore, AE, rather than EoE or MSE, is a good measure of static standing postural stability. Furthermore, the comparison of EoE and AE plots exhibited an inverted U curve, which is another example of a complexity versus disorder inverted U curve.

Definitive surgical resection is the preferred treatment for early-stage non-small-cell lung cancer (NSCLC). Research into genetic alterations, including epidermal growth factor receptor (EGFR) mutation, in early stage NSCLC remains insufficient. Here, we investigated the prevalence of genetic alterations in early-stage NSCLC and the association between EGFR mutation and recurrence after complete resection. Between January 2019 and December 2021, 659 patients with NSCLC who underwent curative surgical resection at a single regional cancer center were recruited. We compared the clinical and pathological data between the recurrence and non-recurrence groups. Multivariate logistic regression was used to predict the risk factors for recurrence. Among the 659 enrolled cases, the most common histology was adenocarcinoma (74.5%), followed by squamous cell carcinoma (21.7%). The prevalence of EGFR mutation was 43% (194/451). Among them, L858R point mutation and exon 19 deletion was 52.3% and 42%, respectively. ALK rearrangement was found at 5.7% (26/453), and ROS1 fusion was found at 1.6% (7/441). The recurrence rate of the entire population was 19.7%. In multivariate analysis, the presence of EGFR mutation, stage II or III (vs. stage I), and pathologic subtype (presence of solid type) were associated with recurrence. Among the recurred group, 86.5% of the patients with EGFR mutation experienced distant recurrence compared to only 66.7% of wild-type (p = 0.016), with no significant difference in median disease-free survival (p = 0.983). In conclusion, the prevalence of EGFR mutation, ALK rearrangement, and ROS1 fusion was 43.0%, 5.7%, and 1.6%, respectively in patients with early-stage NSCLC who underwent curative resection. Along with stage II/III and solid pathologic subtype, EGFR mutation was an independent risk factor for recurrence. In the recurrence group, the rate of distant metastasis was higher in patients with EGFR mutation than in those with wild-type.

Echinococcus granulosus is a harmful cestode parasite which could cause Cystic Echinococcosis in humans, various livestock species and wild animals. Calmodulin (CaM), a Ca²⁺ sensor protein, is widely expressed in eukaryotes and mediates a variety of cellular signaling activities. In our study, the CaM in Echinococcus granulosus (rEgCaM) was successfully cloned and the molecular and biochemical characterizations of rEgCaM were identified. The results showed that rEgCaM was a highly conserved calcium-binding protein, consisting of 149 amino acids. Immunoblot analysis revealed that rEgCaM could be identified using E. granulosus infected sheep serum. The usage of rEgCaM as antigen was evaluated by indirect ELISA which exhibited a high sensitivity of 90.3% but low specificity (47.1%). rEgCaM was mainly located in the tegument tissues and parenchymal region of protoscoleces, the tegument and inner body of adult worm and predominantly expressed in the germinal layer. The mRNA expression of rEgCaM in PSCs were gradually decreased with the increase death of PSCs. In electrophoretic mobility tests and ANS assays, rEgCaM showed a typical calcium-binding protein characteristics. This is the first report on CaM from E. granulosus and rEgCaM is considered to be involved in some important biological function of E. granulosus as a calcium-binding protein.

Cisplatin induces early-onset ototoxicity, resulting in hearing loss. The exact mechanism by which cisplatin causes ototoxicity remains unclear. The purpose of this study was to identify the involvement of receptor-interacting protein kinase(RIP)3-dependent necroptosis in cisplatin-induced ototoxicity in animal models. Sprague–Dawley rats (SD, 8 week) were treated via intraperitoneal (i.p) injection with cisplatin (16 mg/kg for 1 day), and their hearing thresholds were was measured by the auditory brainstem response (ABR) method. Hematoxylin and eosin (H-E) staining, immunohistochemistry, and western blots were performed to determine the effect of cisplatin-induced ototoxicity on cochlear morphology. H-E stains outlined necroptotic changes in the organ of Cortis (OCs) and spiral ganglion neurons (SGNs). Additionally, immunohistochemistry and western blot analysis showed overexpression of RIP3 in the OCs and SGNs that were treated with cisplatin. These results suggest that RIP3-dependent necroptosis was substantial in cisplatin-induced ototoxicity; inner cochlear regions, the OCs, and SGNs were especially sensitive to necroptosis.

The Chinese honeybee (Apis cerana cerana) sacbrood virus (CSBV) causes death of larvae and colony collapse, and could damage the beekeeping industry in China. We sequenced complete genomes of CSBV strains derived from the Maerkang area, Wenjiang area, and Wanyuan area of Sichuan province of China. The genome length of CSBV strains from Sichuan was 8863bp, and it contained one complete Open Reading Frame of a gene with 8544 bp that encoded a protein with 2848 amino acids. The (G+C) % and (A+T) % composition ranged from 40.6 to 40.7 and 59.3 to 59.4, respectively. A phylogenetic tree was constructed using the three CSBV strains and previously reported SBV and CSBV sequences from other regions. We found that viral strains clustered based on their region of origin and host species. The genetic sequences of the CSBV strain from Maerkang were 98.7% and 99.6% similar to CSBV strains from Wanyuan and Wenjiang, respectively. In addition, CSBV from Maerkang had 88.4%-95.2% sequence similarity to previously published genomes of CSBV or SBV from other areas. The VP1 gene sequenced in our study had a 43 bp deletion compared to VP1 sequences of CSBV from other regions in Asia. We detected 10 antigenic determinants on the VP1 protein of CSBV form Aba. Our study provides new insight into the diversity of CSBV strains in China and may help with identifying methods to prevent infection of honeybee colonies.

In order to reduce the large damage caused by train derailment, protective facilities of various shapes and conditions can be installed on railroad tracks. These protective facilities are referred to as derailment containment provisions (DCPs) and three different types are used worldwide. However, there are no clear standards for DCPs design such as installation location, size, and design load, and performance verification of DCPs installed in the actual railway field is not sufficiently performed. In this paper, the functionality of DCPs is analyzed through the full-scale derailment test. In order to propose a method for estimating the collision load acting on the DCP type I after derailment, the experimental results and simulation results are compared. The function of DCP type I according to the change of the vehicle's center of gravity is identified through comparative analysis of the post derailment behavior.

Large quantities of clothing are routinely discarded, ending up in landfills that contribute to the environmental crisis; hence, it is worthwhile investigating how to dispose of this waste in a sustainable way. This study considered environmental values and prosocial behavior from a behaviorism theory. The aim was to set up an environmental protection model for the sustainable disposal of consumer clothing. A structural equation modeling analysis of 407 undergraduate and postgraduate consumer data in Taiwan revealed that consumers’ choice to donate clothing was influenced by environmental values and prosocial behaviors. Clothing resale was influenced by the factor of prosocial behavior. However, prosocial consumers used other disposal patterns instead of resale. Clothing reuse was not influenced by either environmental values or prosocial behavior. The results indicated that environmental values and prosocial behavior did in fact influence consumers’ choices regarding clothing donation. However, prosocial consumers used other disposal patterns instead of resale. Behaviorism theory model is effective in analyzing the factors influencing sustainable clothing disposal. To face clothing waste issues, one can intensify traditional values of industriousness and thriftiness, of compassion and sympathy to others, to accelerate the promotion of the sustainable disposal of clothing.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

This study presents a novel approach for quantifying the dynamics of monthly hydraulic geometry relationships in the Jingjiang reach of the Yangtze River by integrating leaf area index (LAI) data as an indicator of riparian vegetation. A comprehensive system of ordinary differential equations (ODEs) couples traditional power-law hydraulic geometry equations with LAI, capturing the influence of erosion control on channel morphology. The periodic delayed response theory and automatic differentiation techniques are employed to enhance the modeling framework's capabilities. Calibration and verification demonstrate the models' effectiveness in capturing overall trends in discharge, width, and depth dynamics, outperforming traditional constant-parameter approaches. However, model predictive abilities are limited under extreme climate conditions due to training on normal climate data. Key assumptions, including the periodic delayed response theory's neglect of peak discharges, simplified representation of artificial cut-offs, and reliance on remotely sensed data with limited local validation, introduce uncertainties. The proposed modeling framework shows potential for broader application to other river systems with appropriate adjustments. Future research could incorporate additional environmental factors, integrate models across scales, couple with advanced simulation techniques, and expand stability assessments beyond the riverbed index. By addressing related challenges, this integrated approach lays a foundation for enhancing understanding of river morphodynamics and channel stability.

Lindera obtusiloba Blume has several activities, such as anti-inflammatory, anti-allergic, anti-tumor, anti-wrinkle, and antioxidant activities. Interleukin-6 (IL-6) is a classic pro-inflammatory cytokine that is associated with various functions, such as proliferation, invasion, inflammatory responses and functions within antioxidant defence systems. In this study, we investigated IL-6-induced STAT3 activation of lignan compounds isolated from L. obtusiloba. The structures of the isolated compounds were elucidated via spectroscopic nuclear magnetic resonance (NMR) and electrospray ionization mass spectrometry (ESI-MS). As a result, seven lignans were identified from L. obtusiloba. All the isolated compounds (1-7) were evaluated for their IL-6-induced STAT3 inhibitory effects in Hep3B cells using a luciferase reporter assay. Of the isolates, compounds 1 and 5 showed inhibitory effects against IL-6-stimulated STAT3 activation. Furthermore, the mRNA expression levels of inflammation-related genes such as CRP, IL-1b, and SOCS3 were significantly reduced by exposure to compound 1 and 5. The protein levels of p-STAT3, p-JAK2 in IL-6 induced U266 cells were regulated in the presence of lignans derived from Lindera obtusiloba by western blot assay. Based on the results, this study of L. obtusiloba demonstrates that the species has promise as a bioactive candidate for the treatment of IL-6-induced STAT3-related disease.

Various colors of clothing originating from synthetic dyes are presently causing serious environmental pollution problems, whereas natural dyes extracted from natural indigo plants help reduce the harm to the environment and extend the sustainable use of clothing. This study focuses on the relation between indigo dyeing colors and the environment on the basis of sustainable design. The results reveal that light colors are considered to conform to the sustainable spirit more than dark colors in different indigo colors. In fact, the recyclable light-colored indigo dyeing t-shirt is beneficial in its reuse. Indigo dyeing fabric can be decomposed by a variety of microorganisms; however, the light-colored indigo dyeing takes a short time. Light colored indigo dyeing is more resource-saving when considering dye, water and electricity costs. The results of colors and environmental protection provide scheme references to consumers or industry for clothing collocation of different indigo dyeing colors for a series of blue clothing and carry out the ideal of the sustainability and co-existence between clothing and natural resources.

Hang-ju was one of five officinal varieties of Flos chrysanthemum for its edible and potable usage. Besides Flos Chrysanthemum (FL), there were also Bud Chrysanthemum (BC) and Fetal Chrysanthemum (FC) at the early and late stage of buds, respectively, in the consumption market of Hang-ju with higher prices. Whether the quality and efficiency of BC and FC was superior to FL or merely consumption misunderstandings? Three commercial products of Hongxinju, a representive cultivar of Hang-ju were studied with a GC-MS based metabolomics approach, complemented with morphology, contents of moisture and protein and the anti-oxidant activity, to reveal the metabolic alterations of violate components in Hongxinju in different flowering stage and at different processing periods. It revealed that most of the violate components were increased from fresh FC to FL, and the low-boiling fractions, inflammatory methyl arachidonate and air-polluting component of ethylbenzene were declined while the representative components with pungent flavor and cool nature of a-curcumene and (Z,Z,Z)-9,12,15-octadecatrienoic acid, vision improving carotenol of rhodopin and high-boiling fractions were elevated after processed in final FL compared with that in BC and/or FC. Though the content of protein and anti-oxidative capacity of final BC and FC were nearly equal to those of FL, in comprehensive consideration of the representative components related with the efficiency in heat cooling and vision improving, as well as the representative components related with inflammation and air-pollution, final FL was recommended other than BC and FC in the practice of medicine with the yield and quality integrated into account.

Atypical hemolytic uremic syndrome (aHUS) is a rare and life-threatening disease characterized by microangiopathic hemolytic anemia, thrombocytopenia, and acute kidney injury, necessitating differentiation from other thrombotic microangiopathy disorders. Definitive biomarkers for disease diagnosis and activity are currently lacking, and identifying molecular markers is essential. We conducted single-cell sequencing on peripheral blood mononuclear cells from 13 aHUS patients, 3 aHUS family members, and 4 healthy controls. Analysis included clustering, cell type annotation, pseudotime estimation, and cell-cell communication. Immune cell populations differ among aHUS, aHUS families, and healthy controls. Disease activity and treatment influence T, NK, B, and monocyte subpopulations, with increased intermediate monocyte levels distinguishing aHUS from controls and aHUS groups with varying disease activity. Subclustering revealed differential gene expression in patients compared to controls; higher expression of mitochondria-related genes suggests cell metabolism may influence clinical course. Pseudotime trajectory analysis demonstrated unique immune cell differentiation, and cell-cell interaction analysis identified distinct signaling pathways among patients, family members, and controls. This single-cell sequencing study is the first to confirm immune cell dysregulation in aHUS pathogenesis, offering valuable insights into molecular mechanisms and potential new diagnostic and disease activity markers.

Stem cells are undifferentiated cells which can give rise to any types of cells in our body. Hence, they have been utilized for various applications such as drug testing and disease modeling. However, for the successful of those applications, the survival and differentiation of stem cells into specialized lineages should be well controlled. Growth factors and chemical agents are the most common signals to promote the proliferation and differentiation of stem cells. However, those approaches holds several drawbacks such as the negative side effects, degradation or denaturation, and expensive. To address such limitations, nanomaterials have been recently used as a better approach for controlling stem cells behaviors. Graphene oxide is the derivative of graphene, the first 2D materials in the world. Recently, due to its extraordinary properties and great biological effects on stem cells, many scientists around the world have utilized graphene oxide to enhance the differentiation potential of stem cells. In this mini review, we highlight the key advances about the effects of graphene oxide on controlling stem cell growth and various types of stem cell differentiation. We also discuss the possible molecular mechanisms of graphene oxide in controlling stem cell growth and differentiation.

Aberrant neutrophil extracellular trap (NET) formation and the loss of barrier integrity in inflamed intestinal tissues have long been associated with inflammatory bowel disease (IBD). However, whether NETs alter intestinal epithelium permeability during colitis remains elusive. Here, we demonstrated that NETs promote the breakdown in intestinal barrier function for the pathogenesis of intestinal inflammation in mouse models of colitis. NETs were abundant in the colon of mice with colitis experimentally induced by dextran sulfate sodium (DSS) or 2,4,6-trinitrobenzene sulfonic acid (TNBS). Analysis of the intestinal barrier integrity revealed that NETs impaired gut permeability, enabling the initiation of luminal bacterial translocation and inflammation. Furthermore, NETs induced the apoptosis of epithelial cells and disrupted the integrity of tight junctions and adherens junctions. Intravenous administration of DNase I, an enzyme that dissolves the web-like DNA filaments of NETs, during colitis restored the mucosal barrier integrity which reduced the dissemination of luminal bacteria, and attenuated intestinal inflammation in both DSS and TNBS models. We conclude that NETs serve a detrimental factor in the gut epithelial barrier function leading to the pathogenesis of mucosal inflammation during acute colitis.

The search for improved therapeutic approaches to breast cancer are still on going. Breast tumor kinase (BRK, also known as PTK6) is one of the targets, it is highly expressed in breast carcinomas while displaying low or no expression in the normal mammary gland, which hints at the oncogenic role of this enzyme in breast cancer. In these twenty years, an increasing number of studies have focused on understanding the cellular roles of BRK in breast cancers. This review outlines the advances made towards understanding the cellular and physiological role of BRK, the molecular and chemical inhibitors and its therapeutic significance in breast cancer.

Health services research is a multidisciplinary discipline that aims to improve population health by studying healthcare services' organization, delivery, and financing. Over time, the field has worked to define its boundaries and establish a set of core research topics and methods addressing population wellbeing, access, quality, and cost. Although the influence of health technology is significant, our literature survey on health services research showed that SCs in general—containing their management, cost, and policy—had received little attention. Importantly, our assessment also showed that the system’s readiness to handle supply policy and supply device deficiencies like those encountered during pandemic was hardly ever mentioned. Reduced open areas and water bodies, deteriorating infrastructure, and changes in the biological morphology all affect cities’ uncontrollable and unplanned growth. Urban amenities, facilities, and healthcare services were unevenly distributed due to this unchecked urban population development. In light of this, this research suggests two reliable models for site selection issues for one of Hong Kong’s main hospitals. Levels of uncertainty, infeasibility tolerance, and reliability are taken into consideration. Then, two categories of uncertainty—symmetric and bound-ed—were examined. As a result, the challenge of scheduling in uncertainty has been considered, and potential solutions have been presented using a specified probability distribution function. The paper concludes by introducing the specific justice and health problems and outlining four typical strategies. In order to ensure that medications and other healthcare supplies are produced, distributed, and given to patients, a vast network of systems, components, and procedures must be effectively managed. This research contributes in this regard. Also, its grantee fairness in health systems and the populations health locally, nationally, and globally. It highlights health inequity, advances the measurement of health inequity, and promotes public dialogues on health inequity.

A scalable optical convolutional neural network (SOCNN) based on free-space optics and Koehler illumination was proposed to address the limitations of the previous 4f correlator system. Unlike Abbe illumination, Koehler illumination provides more uniform illumination and reduces crosstalk. SOCNN allows for scaling up of the input array and the use of incoherent light sources. Hence, the problems associated with 4f correlator systems can be avoided. We analyzed the limitations in scaling the kernel size and parallel throughput and found that SOCNN can offer a multilayer convolutional neural network with massive optical parallelism.

The spatial heterogeneity in hydrologic simulations is a key difference between lumped and distributed models. Not all distributed models benefit from pedo-transfer functions based on soil properties and crop-vegetation dynamics. Mostly coarse scale meteorological forcing is used to estimate water balance at the catchment outlet only. Mesoscale hydrologic model (mHM) is one of the rare models that incorporates remote sensing data i.e. leaf area index (LAI) and aspect to improve actual evapotranspiration (AET) simulations and water balance together. The user can select either LAI or aspect to scale PET. However, herein we introduced a new weighting parameter “alphax” that allows user to incorporate both LAI and aspect together for PET scaling. With this mHM code enhancement, the modeler has an also option of using raw PET with no scaling. In this study, streamflow, and AET are simulated using the mesoscale Hydrological Model (mHM) in Main (Germany) basin for the period of 2002-2014. The additional value of PET scaling with LAI and aspect for model performance is investigated using Moderate Resolution Imaging Spectroradiometer (MODIS) AET and LAI products. From 69 mHM parameters, 26 parameters are selected for calibration using Optimization Software Toolkit (OSTRICH). For calibration and evaluation, KGE metric is used for water balance and SPAEF metric is used for evaluating spatial patterns of AET. Our results show that AET performance of the mHM is highest when using both LAI and aspect indicating that LAI and aspect contain valuable spatial heterogeneity information from topography and canopy (e.g., forests, grasslands, and croplands) that should be preserved during modeling. The additional “alphax” parameter makes the model physically more flexible and robust as the model can decide the weights according to the study domain.

This study explores the use of satellite-based LULC (Land Use / Land Cover) data while simultaneously correcting potential evapotranspiration (PET) input with Leaf Area Index (LAI) to increase the performance of a physically distributed hydrologic model. The mesoscale hydrologic model (mHM) was selected for this purpose due to its unique features. Since LAI input informs the model about vegetation dynamics, we incorporated the LAI based PET correction option together with multi-year LULC data. The Globcover land cover data was selected for the single land cover cases, and hybrid of CORINE (coordination of information on the environment) and MODIS (Moderate Resolution Imaging Spectroradiometer) land cover datasets were chosen for the cases with multiple land cover datasets. These two datasets complement each other since MODIS has no separate forest class but more frequent (yearly) observations than CORINE. Calibration period spans from 1990 to 2006 and corresponding NSE (Nash-Sutcliffe Efficiency) values varies between 0.23 and 0.42, while the validation period spans from 2007 to 2010 and corresponding NSE values are between 0.13 and 0.39. The results revealed that the best performance is obtained when multiple land cover datasets are provided to the model and LAI data is used to correct PET, instead of default aspect-based PET correction in mHM. This study suggests that to minimize errors due to parameter uncertainties in physically distributed hydrologic models, adequate information can be supplied to the model with care taken to avoid over-parameterizing the model.

This paper studies the evaporative heat transfer characteristics of R744 at low temperatures in a horizontal smooth tube as a cascade refrigeration system (CRS) among hybrid cascade refrigeration systems (HCRSs). There is a lack of research on the low-temperature evaporative heat transfer characteristics of R744 under the operating conditions of evaporators used in actual CRSs used in supermarkets. Therefore, this study aims to provide basic data on the evaporative heat transfer characteristics of R744 in the evaporators of refrigerators used in supermarkets. The tube used in the evaporation experiment conducted herein was a smooth horizontal copper tube with an inner diameter and length of 11.46 mm and 8000 mm, respectively. The experimental pa-rameters were as follows: heat fluxes of 12–21.5 kW/m2, mass fluxes of 75–225 kg/(m2·s), and saturation temperatures of −50–−30 °C. The main results are summarized as follows. (1) When designing the R744 evaporator, the mass and heat fluxes must be maximized within the operating conditions, and the saturation temperature must be designed to be as low as possible. (2) The evaporative heat transfer coefficient of R744 can be predicted well by using the correlation formula of Chen at the evaporation temperature of −40 °C in the CRS.

In the wake of increasing digital fraud, this paper introduces an innovative application of Artificial Intelligence (AI) in detecting fraudulent activities across finance, healthcare, and e-commerce sectors. It presents a detailed analysis of machine learning methodologies, specifically focusing on the advantages of supervised, unsupervised, and deep learning techniques. The paper addresses the challenges such as data imbalance, model interpretability, and ethical implications in AI-based fraud detection. It also discusses the necessity of high-quality datasets and advocates for the integration of traditional and advanced machine learning methods to enhance accuracy and adaptability in fraud identification. However, it acknowledges the limitations including computational demands and overfitting risks. The study underscores the importance of collaborative efforts between AI experts and industry professionals to develop ethical, efficient, and reliable AI solutions for fraud detection.

Biocontrol strategies are gaining tremendous attention with the growing awareness of the irreparable harm caused by the continuous use of synthetic pesticides. This study examines the proteolytic and chitinolytic activities of Bacillus velezensis CE 100 and its termiticidal effect through cuticle degradation. The proteolytic and chitinolytic activities of B. velezensis CE 100 systematically increased with cell growth to the respective peak of 68.3, and 128.3 units/mL after seventh days of inoculation, corresponding with the highest cell growth of 16 x 107 colony forming units (CFU)/mL. The in vitro termiticidal assay showed that B. velezensis CE 100 caused a rapid and high rate of termite mortality with the median lethal time (LT50) of &gt; 1h, and the highest mortality rate of 91.1% and 92.2% recorded at 11h and 12h in the bacterial broth culture and crude enzyme fraction, respectively. In addition to broken setae and deformed sockets, termites treated with the bacterial broth culture exhibited degraded epicuticles, while the crude enzyme fraction caused severe disintegration of both the epicuticle and endocuticle. These results indicate a tremendously higher prospect of B. velezensis CE 100 in the biological control of subterranean termites compared to the previously used entomopathogenic bacteria.

Corresponding to the principles of biological synapses, an essential prerequisite for hardware neural networks using electronics devices is continuous regulation of conductance. We implemented artificial synaptic characteristics in a (GeTe/Sb2Te3)16 iPCM with a superlattice structure under optimized identical pulse trains. Based on atomically controlling the Ge switch in the phase transition that appears in the GeTe/Sb2Te3 superlattice structure, multiple conductance states were implemented by applying the appropriate electrical pulses. Furthermore, we found that the bidirectional switching behavior of a (GeTe/Sb2Te3)16 iPCM can achieve a desired resistance level using the pulse width. Therefore, we also fabricated a Ge2Sb2Te5 PCM and designed a pulse scheme based on the phase transition mechanism to compare to the (GeTe/Sb2Te3)16 iPCM. We designed an identical pulse scheme that implements linear and symmetrical LTP and LTD based on the iPCM mechanism. As a result, the (GeTe/Sb2Te3)16 iPCM showed relatively excellent synaptic characteristics by implementing gradual conductance modulation, a nonlinearity value of 0.32, and LTP/LTD 40 conductance states using identical pulses trains. Our results demonstrate the general applicability of the artificial synaptic device for potential use in neuro-inspired computing and next generation non-volatile memory.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

Music therapy has served as complementary and alternative medicine for various neurological disorders. Five Phases Music Therapy (FPMT) employs the theory of five phases and five music scales or tones (宫Gong (do), 商Shang (ri), 角Jue (mi), 徵Zhi (so) and 羽Yu (la)) to analyze and treat mind-body illness. In Chinese Medicine (CM), the five music scales are used to connect the human body and the universe, interpret personalities and constitution and analyze the influences of climatic changes on health. FPMT has a self-contained theory and routine of practice application. Large amounts of clinical and fundamental reports have been available and clinical benefits have been obtained. However more systemic clinic research esp. evidence-based and random controlled trials must be performed to validate and optimize its routines and biological and neurological mechanism must be further explored. It’s reasonable to believe that the effective music therapy will attract more attention from the world outside China with the introduction of FPMT.

This manuscript critically reviews the design and delivery of spray-dried particles for the achievement of high total lung doses (TLD) with a portable dry powder inhaler. We introduce a new metric termed the product density, which is simply the TLD of a drug divided by the volume of the receptacle it is contained within. The product density is given by the product of three terms: the packing density (the mass of powder divided by the volume of the receptacle), the drug loading (the mass of drug divided by the mass of powder), and the aerosol performance (the TLD divided by the mass of drug). This manuscript discusses strategies for maximizing each of these terms. Spray drying at low drying rates with small amounts of a shell-forming excipient (low Peclet Number) leads to formation of higher density particles with high packing densities. This enables ultrahigh TLD (>100 mg of drug) to be achieved from a single receptacle. Emptying of powder from capsules is directly proportional to the mass of powder in the receptacle, requiring an inhaled volume of about 1 L for fill masses between 40 and 50 mg and up to 3.2 L for a fill mass of 150 mg.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

Construction productivity entails a wide range of work combinations. When human resources are scarce, it is critical to replace manpower with machinery, and calculating machinery productivity is crucial. Traditional labor productivity methods, however, cannot address dredging complex multi-attribute decision-making (MADM) problems. Aiming to address the limitations of the traditional labor productivity method, this paper extends the data envelopment analysis (DEA) and proposes a new dredging productivity evaluation method. The proposed method can solve the problem of evaluating various combinations of factors (single-input, multiple-input, sin-gle-output, and multiple-output) and the problem suggesting that the efficiency of the DEA method'scalculation results is equal to 1. The effectiveness of the proposed method was verified using reservoir dredging examples. The simulation results show that the proposed method has broad applicability, can accurately evaluate the related dredging performance issues, and provide directions for construction managers to improve labor productivity.

No research to date has explored the possibility of context-specific, within-relationship fluctuation in attachment security. In this present article, two cross-sectional studies were designed (1) to develop and validate context-specific attachment scales in Traditional-Chinese, and (2) to explore fluctuations in within-parent attachment security between the contexts of sport and academics, in relation to global attachment patterns and indicators of psychological wellbeing. Results indicated that youth can and do perceive within-parent attachment patterns differently depending upon context but that the relationship of such differences to context-specific outcomes is complex. Of particular interest was that the degree of within-parent attachment variability between contexts was clearly and negatively related to indices of psychological wellbeing. This suggests that contextual variation may be a meaningful and useful way to explore within-parent attachment fluctuation.

There are four categories of medical waste that cannot be mixed as this will cause serious problems such as environmental pollution or infection. In the past, the classification of medical waste often involved a lot of human and material resources to process, with workers at risk of exposure to infectious substances. Therefore, an augmented reality (AR) and artificial intelligence (AI) medical waste classification system and method were developed. This innovative medical waste classification system and method combines AR and AI identification technology to reduce the risk of manual judgment errors by clinical staff when handling medical waste.

This study aimed to investigate how transplanting date affects the agronomic and grain quality traits of two early maturing rice varieties. The experiment was conducted in the rice research field of Chungnam Agricultural Research and Extension Services, South Korea and rice materials were transplanted at intervals of approximately 15 days from April 16 to July 16 in 2019 and 2020. Results showed that agronomic and grain quality traits varied according to the transplanting date, and earlier transplanting resulted in the longer period of days from transplanting to heading (DTH). The spikelet number m-2 was highly correlated with the milled rice yield (r = 0.963** for Jinbuol, r = 0.909** for Yeoreumi) and it significantly decreased as the transplanting date was delayed, which was leading to lower yield. Environmental factors, the mean temperature during the grain filling stage, had a negative correlation with head rice rate (r2 = 0.825** for Jinbuol, r2 = 0.803** for Yeoreumi), and the number of days from transplanting to heading showed negative correlation with protein content (r2 = 0.777** for Jinbuol, r2 = 0.833** for Yeoreumi). Therefore, increasing the number of days from transplanting to heading date can lead to higher milled rice yield and lower protein content, and avoiding heading dates on July 17 can improve the appearance traits. As a results, it is suggested that early transplanting is advantageous to increase the milled rice yield and grain quality of early maturing rice.

Change orders have received considerable attention from researchers thus far, but none have considered pricing strategies of change orders through the interaction between general contractors and subcontractors. Previous studies found that contractors’ opportunistic bidding considering beyond-contractual reward (BCR) in the execution stage can be reduced by improving the construction management system and strengthening the supervision of contractors’ performance. However, the BCR remains in ecology of construction engineering. This study proposes an integrated evolutionary game theory-system dynamics model (ET-SD model) and simulates the pricing strategy of change orders between general contractors and subcontractors to explore the root cause of BCR phenomenon. Sensitivity analysis on the evolutionary dynamics of payoff is explored. Results reveal that change orders with BCR maintain Nash equilibrium and evolutionary stable strategy (ESS) unless changing the payoff structure between general and subcontractors’ pricing strategies. This study presents important managerial insights from the evolutionary game perspectives, nature of change orders, and payoff of the alternative.

Linear state estimation (SE) formulation under a rectangular coordinate system has been proved to be applicable for real-time distribution network management. Micro phasor measurements’ model can be accommodated into this kind of SE easily. However, voltage magnitude, active power and reactive power measurements are transformed to linear measurements with large node voltage error. To cope with this issue, a linear state estimation under a polar coordinate system is adopted at the first stage to obtain accurate enough complex node voltage, and then nonlinear measurements are transformed to be linear with complex node voltage. At the second stage, linear SE under a rectangular coordinate system can be adopted to satisfy more strict network constraints. The proposed two-stage linear SE is validated on balanced 14, 33, 70,84, 119, 135 nodes network and IEEE 13, 34, 37,123 unbalanced test feeders.

With large-scale distributed generators (DGs) in an active distribution network (ADN), conventional load flow convergence failure is incurred by heavy power transmission. The Holomorphic Embedding Load Flow Method (HELM) has proven to be more robust than the Newton–Raphson method under heavy power transmission. At present, HELM is mainly designed for balanced transmission networks. In this study, we developed a three-phase HELM model to accommodate DGs, delta connection loads, and ZIP loads for ADN. The effectiveness and better performance of the proposed method under heavy load situations were validated using modified unbalanced IEEE 13, 34, 37, and 123 test feeders.

Sustainable urban design or planning is not a LEGO-like assembly of prefabricated elements, but an embryo-like growth with persistent differentiation and adaptation towards a coherent whole. The coherent whole has a striking character – called living structure – that consists of far more small substructures than large ones. To detect the living structure, natural streets or axial lines have been previously adopted to be topologically represent an urban environment as a coherent whole. This paper develops a new approach to detecting the underlying living structure of urban environments. The approach takes an urban environment as a whole and recursively decomposes it into meaningful subwholes at different levels of hierarchy or scale ranging from the largest to the smallest. We compared the new approach to natural street and axial line approaches and demonstrated, through four case studies, that the new approach is better and more powerful. Based on the study, we further discuss how the new approach can be used not only for understanding, but also for effectively designing or planning the living structure of an urban environment to be more living or more livable.

COVID-19 is a highly infectious respiratory illness caused by SARS-CoV-2, and acute lung injury (ALI) is the major cause of COVID-19. The challenge in studying SARS-CoV-2 pathogenicity is the limited availability of animal models. Therefore, it is necessary to establish animal models that can reproduce multiple characteristics of ALI to study therapeutic applications. The present study established a mouse model that has features of ALI that are similar to COVID-19 syndrome to investigate the role of ACE2 and the administration of the Chinese herbal prescription NRICM101 in ALI. Mice with genetic modifications, including overexpression of human ACE2 (K18-hACE2 TG) and absence of ACE2 (mACE2 KO), were intratracheally instillated with hydrochloric acid. The acid intratracheal instillation induced severe immune cell infiltration, cytokine storms, and pulmonary disease in mice. Compared with K18-hACE2 TG mice, mACE2 KO mice exhibited dramatically increased levels of multiple inflammatory cytokines (IL-6, TNF-α, and TGF-β1) in bronchoalveolar lavage fluid, histological evidence of lung injury, and dysregulation of MAPK and MMP activation. In mACE2 KO mice, NRICM101 could ameliorate the disease progression of acid-induced ALI. In conclusion, the established mouse model provided an effective platform for researchers to investigate pathological mechanisms and develop therapeutic strategies for ALI, including COVID-19-related ALI.

The purpose of this study is to develop a cranial traction therapy program to help correct facial asymmetry of the hard tissues through the means of the treatment of soft tissues—a non-surgical therapeutic method for the correcting of facial asymmetry. We have formed a group of experts who have agreed to the study. In the primary survey, open questions were used. In the second survey, the results of the first survey were summarized and the degree of agreement was presented to the questions in each category. In the third survey, we conducted a statistical analysis of the degree of agreement on each item of question. All surveys also performed email. The distribution was calculated using the SPSS (ver.23.0) program, and the mean difference between the result and X² was calculated. The significance level was set to p&lt;.05. Most of the questions attained a certain level of consensus by the experts (average of 4.0 or higher), it can be said that most are important and suitable questions. the results regarding the degree of importance for each of the points of evaluation made by the groups of experts in both the second and third stage of the cranial traction therapy program were verified using content validity ratio (CVR 77). The ratio for the cranial traction 13 points of evaluation was within the range of 0.40∼1.00, so the Delphi program for the cranial traction therapy verified that the content was valid.

Conventional methods of crop mapping need ground truth information to train the classifier. Thanks to the frequent acquisition allowed by recent satellite missions (Sentinel 2), we can identify temporal patterns that depend on both phenology and crop management. Some of these patterns are specific to a given crop and thus can be used to map it. Thus, we can substitute ground truth information used in conventional methods with agronomic knowledge. This approach was applied to identify irrigated permanent grasslands (IPG) in the Crau area (Southern France) which play a crucial role in groundwater recharge. The grassland is managed by making three mows during the May-October period which leads to a specific temporal pattern of leaf area index (LAI). The mowing detection algorithm was designed using the temporal LAI signal derived from Sentinel 2 observations. The algorithm includes some filtering to remove noise in the signal that might lead to false mowing detection. A pixel is considered a grassland if the number of detected mows is greater than 1. A data set covering five years (2016-2020) was used. The detection mowing number was done at the pixel level and then results are aggregated at the plot level. A validation data set including 780 plots was used to assess the performances of the classification. We obtained a Kappa index ranging between 0.94-0.99 according to the year. These results were better than other supervised classification methods that include training data sets. The analysis of land-use changes shows that misclassified plots concern grasslands managed less intensively with strong intra-parcel heterogeneity due to irrigation defects or year-round grazing. Time series analysis, therefore, allows us to understand different management practices. Real land-use change in use can be observed, but long time series are needed to confirm the change and remove ambiguities with heterogeneous grasslands.

Typically, a diesel generator on the merchant ship, composed of a wound rotor synchronous generator and a four-stroke diesel engine, supplies electrical power to various loads. Recently, shaft generators for merchant vessels are increasingly replacing diesel generators to reduce CO2 emissions through fuel efficiency improvement. In particular, permanent magnet generators replace induction generators due to their high-efficiency characteristics at light loads. The surface-mounted permanent magnet can be a suitable rotor topology due to the relatively short constant power range. This generator can also operate as a motor according to the propulsion mode, so minimizing the harmonics of the induced voltage and the torque ripple is necessary. This paper proposes an alternative NdFeB magnet pole topology combined with the modular step-skewed rotor. The step-skewed rotor affects to reduce higher-order harmonics, and the modular pole reduces the permanent magnet assembly process and harmonics in voltage and torque. A 2-D finite element method is used to evaluate the harmonics of induced voltage and torque pulsation for the proposed topology. The topology shows harmonic minimization effect by comparing the characteristics of three flatted-bottom magnets. Compared to the tapered bread-loaf magnet, voltage harmonics to the 100th component are almost the same, and the torque ripple is reduced by more than 12% at the same residual flux density. The analysis method is verified by comparing test and analysis results for prototype machines with similar specifications.

We constrain two dynamical dark energy models that are parametrized by the logarithm form of $w(z)=w_{0}+w_{1}\left(\frac{\ln (2+z)}{1+z}-\ln 2\right)$ and the oscillating form of $w(z)=w_{0}+w_{1}\left(\frac{\sin(1+z)}{1+z}-\sin(1)\right)$. Comparing with the Chevallier-Polarski-Linder (CPL) model, the two parametrizations for dark energy can explore the whole evolution history of the universe properly. Using the current mainstream observational data including the cosmic microwave background data and the baryon acoustic oscillation data as well as the type Ia supernovae data, we perform the $\chi^2$ statistic analysis to global fit these models, finding that the logarithm parametrization and the oscillating parametrization are almost as well as the CPL scenario in fitting these data. We make a comparison for the impacts of the dynamical dark energy on the cosmological constraints on the total mass of active neutrinos. We find that the dark energy properties could significantly change the fitting results of neutrino mass. Looser constraints on $\sum m_{\nu}$ are obtained in the logarithm and oscillating models than those derived in the CPL model. Consideration of the possible mass ordering of neutrinos reveals that the most stringent constraint on $\sum m_{\nu}$ appears in the degenerate hierarchy case.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Solid state sensors having timing capabilities are becoming an absolute need in particle tracking techniques of future experiments at colliders. In this sense, silicon sensors having 3D structure are becoming an interesting solution, due to their intrinsic speed and radiation resistance. A characteristics of such devices is the strict dependence of their performance on their geometric structure, which can be widely optimised by design, thus requiring suitable tools for an accurate modeling of their behaviour. This paper illustrates the development, performance and use of the TCoDe simulator, specifically dedicated to the fast simulation of carrier transportation phenomena in solid state sensors. Some examples of its effectiveness in the design and analysis of 3D sensors is also given.

Arid- and semi-arid Central Asia is particularly sensitive to climate change. The changes in extreme precipitation in Central Asia stemming from climate warming are the subject of intense debate within the scientific community. This study employed a Morlet wavelet analysis to examine the annual occurrence number of extreme precipitation in Central Asia from May to September during the period of 1951–2005. Their modulating planetary-scale climate modes were identified by using a linear regression analysis. Two major scales of the temporal variability were derived: 2–3.9 yr and 4–6 yr. The dominant variability was 2–3.9-yr scale and was associated with the negative phase of the Polar/Eurasia (POL) pattern. The 4–6-yr scale provided a secondary contribution and was closely linked to the negative phase of the North Atlantic Oscillation (NAO). These planetary climate modes acted as precursors of extreme precipitation over Central Asia. The negative phase of POL directly contributed to a negative height anomaly over Central Asia, which was intimately related to extreme precipitation. In contrast, the negative NAO phase possibly manifested as a Rossby wave source, which was subsequently exported to Central Asia through a negative–positive–negative Rossby wave train.

The effect of γ-ray irradiation on surface plasmon resonance (SPR) sensing capability of refractive index (n = 1.418–1.448) of the silica glass optical fiber comprised of germano-silicate glass cladding embedded with Au nano-particles (NPs) was investigated. As the γ-ray irradiation increased from 1 hour to 3 hours with the dose rate of 1,190 Gy/h, the morphology of the Au NPs and the SPR spectrum were found to change. The average diameter of Au NPs increased with the aspect ratio from 1 to 2 and the nano-particles became grown to the clusters. The SPR peak wavelength shifted towards longer wavelength with the increase of total dose of γ-ray irradiation regardless of the corresponding refractive indices. The SPR sensitivities (wavelength/refractive index unit, nm/RIU) also increased from 407 nm/RIU to 3,553 nm/RIU, 1,483 nm/RIU, and 2,335 nm/RIU after the γ-ray irradiation at the total dose of 1,190 Gy, 2,380 Gy, and 3,570 Gy, respectively.

Transcutaneous injection laryngoplasty is a well-known procedure for treating paralyzed vocal fold by injecting augmentation material into it. Hence, vocal fold localization plays a vital role in the preoperative planning as the fold location is required to determine the optimal injection route. In this communication, we propose a mirror environment based reinforcement learning (RL) algorithm for localizing the right and left vocal folds in preoperative neck CT. RL-based methods commonly showed noteworthy outcome in general anatomic landmark localization problem in the recent years. However, such methods suggest training individual agent for localizing each fold, though the right and left vocal folds are located in close proximity and have high feature-similarity. Utilizing the lateral symmetry between the right and left vocal folds, the proposed mirror environment allows for a single agent for localizing both the folds by treating the left fold as a flipped version of the right fold. Thus, localization of both folds can be trained using a single training session which utilizes the inter-fold correlation and avoids redundant feature learning. Experiment with 120 CT volumes showed improved localization performance and training efficiency of the proposed method compared with the standard RL method.

Artificial sweeteners are widely used food ingredients in beverages and drinks to lower calorie intake which in turn prevent lifestyle diseases such as obesity. Epidemiological evidences suggest that an overdose of artificial sweeteners could result to adverse effects after consumption. Thus, our study aims to systematically explore the potential adverse effects of eight commercial artificial sweeteners, including acesulfame-K, alitame, aspartame, sodium cyclamate, dulcin, neotame, saccharin and sucralose on cardiac performances of zebrafish (Danio rerio) and Daphnia as model animals. Embryonic zebrafish and Daphnia were exposed to eight artificial sweeteners at 100 ppb concentrations and their cardiac performance (heart rate, ejection fraction, fractional shortening, stroke volume, cardiac output and heartbeat regularity) were measured and compared. Saccharin significantly increased the heart rate of zebrafish larvae while a significant decrease was observed in Daphnia. Significant increase was also noted in zebrafish heart rate variability after incubation in acesulfame K, dulcin, sodium cyclamate, and sucralose. However, a significant increase in Daphnia was only observed after incubation in dulcin. Based on Principal Component Analysis (PCA) and hierarchical clustering results, several artificial sweetener samples were species-specific to zebrafish and Daphnia. Our study demonstrates the potential adverse physiological effects of artificial sweeteners in cardiovascular systems of zebrafish larvae and Daphnia.

Confronting the dual challenges of rapid urbanization and climate change, although extensive research has investigated the influencing factors and practical strategies of urban carbon emissions and urban vibrancy, respectively, the unclear mutual nexus between them and the development strategy of collaborative optimization requires further in-depth analysis. This study explores the delicate balance between urban vibrancy and low-carbon sustainability within the confines of Beijing’s Fifth Ring Road. By integrating OpenStreetMap, land use, population, and building carbon emission data, we have developed a reproducible method to estimate total carbon emission and emission intensity per capita. Furthermore, we have introduced vibrancy index data to distinguish the vibrancy evaluation of residential and non-residential land and applied cross-combinational classification technology to dissect the spatial correlation between urban carbon emissions and urban vibrancy. The results reveal that the four combination typologies show more significant differences and regularity in residential land. Based on the discovery of spatial correlation, this study puts forward corresponding development strategy suggestions for each typology based on geographical location and the requirements of urban development policies of these four combination typologies. In conclusion, our study highlights the importance of integrating carbon emissions and urban vibrancy comprehensively in sustainable urban planning and proposes that various land use combinations need targeted development strategies to achieve this goal, which need to consider population, energy, service facilities, and other diverse aspects.

This study focuses on the impact of weak partial discharges (PDs) on defect recognition accuracy in epoxy resin through phase-resolved partial discharge (PRPD) analysis. Two measurement conditions are compared until PRPD pattern saturation: one-minute and one-hour durations. The PD data specifically target three void types located at different positions within the epoxy material. The aim is to evaluate how the presence of weak PDs at the PD extinction voltage (PDEV) influences defect recognition accuracy. This research sheds light on the potential implications of neglecting the significance of weak PD signals in defect detection. A convolutional neural network (CNN) model is trained using PRPD data recorded at the PD inception voltage (PDIV) and tested using the new PRPD data from both conditions recorded from a lower PDIV to a PDEV. The trained CNN model achieves a defect recognition accuracy of 100% for a one-hour duration, highlighting the importance of not neglecting weak PD signals. This emphasizes the significance of extended measurement duration and pattern saturation in capturing and analyzing weak PD signals for improved defect recognition. This study contributes to the advancement of practical applications by understanding the behavior of the epoxy material and enhancing defect detection techniques.

A digital twin is a virtual representation that serves as the real-time digital counterpart of a physical object or system. Recent advancements have extended the concept of digital twins to humans, incorporating complex biological data such as DNA (Predictiv Care, Inc.) and immune system profiles. These sophisticated models go beyond mere pictorial representations, offering a more holistic digital reflection. However, a significant gap remains. The current human digital twin models are not capable of learning one’s preferences. In this pilot study, we introduce Diginality, a chatbot powered by HyperCLOVA X, a Large Language Model (LLM) developed by NAVER, Inc. Diginality, learns one’s preferences with custom training from data collected by interview-style questions on the user’s topic of interest. Our findings demonstrate that Diginality successfully answers one’s preferences, thereby adding a new dimension to the concept of human digital twins. This work represents a pioneering step towards creating a more comprehensive and psychologically nuanced human digital twin.

Background: Neurological disorders are the leading cause disability in Australia and the world. Combating the perceived difficulty of neurology or “neurophobia” and improving physician education is a key component in addressing this problem. We aim to conduct the first study to identify whether neurophobia exists in medical students and junior doctors in an Australian population and try to identify factors that may contribute to this in this population. Methods: A 24 question online validated survey was distributed via email broadcast to all medical students and junior doctors at a metropolitan tertiary care centre in Australia. Responses were collected over 6 weeks with weekly reminder emails for 4 weeks after the initial invitation email. Results: 114 medical students and junior doctors participated in the study. Participants perceived neurology as the most difficult medical speciality compared to 10 other medical specialties (p=0.001). The top three factors contributing to this perceived difficulty were: a lack of understanding of neuroanatomy, lack of diagnostic certainty and lack of clinical exposure. 65% of the participants stated that they had too little planned teaching in neurology with only 36% of the participants having performed a neurology rotation during medical school. Conclusion: The prevalence of neurophobia in this Australian cohort of medical students and junior doctors is consistent with previous findings from around the world. This concerning finding requires further examination into the contributing factors in order to created trials of targeted interventions in order to resolve this.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Skeletal muscle is a specialized tissue consisting of nondividing and multinucleated muscle fibers. Skeletal muscle-specific myostatin (MSTN) is a secreted protein that acts as a negative regulator of muscle mass by inhibiting proliferation and differentiation of myoblasts. In this study, we established a screening platform to monitor myostatin promoter activity in rat L8 myoblasts. Extract of Glycyrrhiza uralensis (GUE), an oriental herbal medicine, was identified through this screening platform and, the active fractions of GUE were identified by process-scale liquid column chromatography system. For in vivo study, the GUE as a feed additive was investigated in growth-finishing pigs. The results showed that GUE significantly increased body weight, carcass weight and lean content in pigs. Microbiota analysis indicated that GUE did not affect the composition of gut microbiota in pigs. In summary, this established rodent myoblast screening platform was used to identify a myogenesis-related phytogenic, GUE, and further demonstrated that the active fractions inhibited MSTN expression. These finding suggest a novel application for GUE in growth performance enhancement through modulation of MSTN expression. Furthermore, this established screening platform has great potential for identification and evaluation of a wide variety of phytogenics involving in myogenesis.

Bowlby’s (1969/1982) attachment theory has been employed as a broad and integrative framework to explore human wellness across a range of disciplines. Attachment theory has even been labelled one of the last surviving “grand theories” not to have been completely dismissed, replaced, or extensively reworked (e.g., Carr, 2012; Mercer, 2011). However, despite the ubiquitous nature of some of the theory’s fundamental tenets, there are always possibilities for new conceptual development, extension, and revision. In this paper, we critically explore the idea of “context-specific” attachment within parent-child relationships. We briefly outline critical assumptions and key areas of attachment and articulate potential rationale, conceptualisation, and relevance of contextual attachment.

Using morphological characteristics and SSR markers, we evaluated the morphological and genetic variation of 200 Perilla accessions collected from the five regions of South Korea and other region. In morphological characteristics analysis, particularly, leaf color, stem color, degree of pubescence, leaf size were found to be useful for distinguishing the characteristics of native Perilla accessions cultivated in South Korea. A total of 137 alleles were identified in the 20 simple sequence repeat (SSR) markers, and the number of alleles per locus ranged from 3 to 13, and the average number of alleles per locus was 6.85. The average gene diversity (GD) was 0.649, with a range of 0.290-0.828. From analysis of SSR markers, accessions from the Jeolla-do and Gyeongsang-do regions showed comparatively high genetic diversity values compared with those from other regions in South Korea. In the unweighted pair group method with arithmetic mean (UPGMA) analysis, the 200 Perilla accessions were found to cluster into three major groups and an outgroup with a genetic similarity of 42%, and did not showed a clear geographic structure from the five regions of South Korea. Therefore, it is believed that landrace Perilla seeds are frequently exchanged by farmers through various routes between the five regions of South Korea. The results of this study are expected to provide useful information for conservation of these genetic resources and selection of useful resources for the development of varieties for seeds and leafy vegetables of cultivated var. frutescens of Perilla crop in South Korea.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

The electrical motor design requires a lot of work and resources. In the field, motor designers need to decide on competitive motor sizing quickly to compete with other motor suppliers. Generally, it requires expensive FEM S/W to get accurate motor sizing results, but buying and maintaining many licenses is costly. Moreover, it needs some patience to get the result from FEM analysis. In this paper, the motor sizing technique using an existing production motor is presented to respond to urgent requests from customers without using FEM analysis. In order to enhance the fidelity of the result, magnetic flux loss by magnet coating and non-linear characteristics are considered during the motor sizing process. The proposed sizing method was verified by comparison to the FEM analysis and test result and showed reasonable confidence in them. Also, this method has the substantial advantage of outputting accurate results instantly without taking any time. It helps with the modification design of electrical motors without using expensive FEM S/W and a certain level of skill or experience.

Early debridement and stabilization for pyogenic spondylodiscitis allow early mobilization of the patient and prevent subsequent spinal deformity. Tantalum (Ta) trabecular metal (TM) components have several potential advantages over conventional implant materials, such as its uniformity and structural continuity, strength, low stiffness, high porosity, high coefficient of friction and tantalum trabecular metal enhances the host defense mechanism by increasing leukocyte chemotaxis, phagocytosis, and the bacterial killing rate. A single-stage surgery with a tantalum trabecular metal cage combining two different approaches is sufficient to maintain vertebral stability. This retrospective cohort study included 57 patients, 31 (54%) patients were treated with single-stage debridement and reconstruction with trabecular metal cages, and 26 (45.6%) patients received spine surgery without trabecular metal cages received surgery between January 2018 and March 2021 in our tertiary academic teaching hospital. The CRP values dropped borderline significantly in the TM cage group compared with the non-TM cage group postoperatively. In patients with spondylodiscitis, it is advisable to perform single-stage debridement and reconstruction with a trabecular metal cage, which allows abscess drainage and rapid mobilization, prevents deformity.

It is a truism that whole energy system models underpin the development of policies for energy system decarbonisation. But recent reviews have thrown doubt on the appropriateness of such models for addressing the multiple goals for future energy systems, in the face of emergent real-world complexity and the evolution of stakeholder’s priorities. Without an understanding of the changing priorities of policy makers and expectations of stakeholders for future systems, system objectives and constraints are likely to be ill-defined, and there is a risk that models may be inadvertently instrumentalised. Adopting a system architecture perspective, the authors have undertaken a three-year programme of research to explore strategies for decarbonising heat in the UK, with interaction with and elicitation of needs from stakeholders at its heart. This paper presents the procedure, methods, and results of an exercise in which experts from stakeholder organisations across the energy system were interviewed. Analysis of interview data reveals two broad approaches to heat decarbonisation which can be broadly defined as either adaptive or transformative. Specific insights gained from these interviews enabled our modelling teams to refocus their work for exploration with a wider circle of stakeholders. Results suggests that this iterative approach to formalising model-policy interaction could improve the transparency and legitimacy of modelling and enhance its impact on policy making.

In recent years, the demand for coffee has increased tremendously. During the production process, green coffee beans are traditionally screened manually for defective beans before they are packed into coffee bean packages; however, this method is not only time-consuming but also increases the rate of human error due to fatigue. Therefore, this paper proposed a lightweight deep convolutional neural network (LDCNN) for the quality detection system of green coffee beans, which combined depthwise separable convolution (DSC), squeeze-and-excite block (SE block), skip block, and other frameworks. To avoid the influence of low parameters of the lightweight model caused by the model training process, rectified Adam (RA), lookahead (LA), and gradient centralization (GC) were included to improve efficiency; the model was also put into the embedded system. Finally, the local interpretable model-agnostic explanations (LIME) model was employed to explain the predictions of the model. The experimental results indicated that the accuracy rate of the model could reach up to 98.38% and the F1 score could be as high as 98.24% when detecting the quality of green coffee beans. Hence, it can obtain higher accuracy, lower computing time, and lower parameters. Moreover, the interpretable model verified that the lightweight model in this work is reliable, providing the basis for screening personnel to understand the judgment through its interpretability, thereby improving the classification and prediction of the model.

Drug-induced liver injury (DILI) stands as a significant cause of drug attrition. To mitigate clinical DILI risks, assessing drugs using human liver models is crucial since animal studies may fall short due to species-specific liver pathway variations. Cell-based preclinical hepatotoxicity testing is often pertinent. In the present study, cells from a human liver cancer line (HepG2, HepaRG) were cultured in both formats of 2D and 3D spheroids to explore their responses to drugs. Liver-specific marker expressions across cell lines and culture formats were also examined to assess disparities in drug-induced liver injury marker expressions. In cytotoxicity assays, HepG2 cells exhibited heightened sensitivity to amiodarone HCl, while HepaRG cells showed greater sensitivity to acetaminophen. Generally, 2D cultures were more responsive to drugs than 3D cultures. Consistency was observed between cytotoxicity assays and liver injury markers AST and ALT. Variations were also noted in liver cell marker secretion, with albumin and urea concentrations declining post-drug treatment, particularly with higher baseline expression in HepaRG cells and 3D cultures. Additionally, mRNA expression levels of CYP enzymes involved in hepatocellular drug metabolism were compared following treatment with enzyme inducers. CYP1A2 and CYP2C9 were not expressed in HepG2 cells. On the other hand, CYP3A4 was expressed higher in 3D culture than in 2D culture. HepaRG cells exhibited significantly increased expression of all three enzymes post-treatment. Notably, enzyme expression was notably higher in 3D cultures than in 2D cultures. Collectively, these findings suggest that HepaRG cells and 3D cultures hold promise for evaluating DILI during early-stage drug development.

Synthetic cathinones, derived from cathinone found in the plant Catha edulis, represent the second-largest and most frequently seized group of new psychoactive substances. They are considered as β-keto analogs of amphetamine, sharing pharmacological effects with amphetamine and cocaine. This review describes the neurotoxic properties of synthetic cathinones, encompassing their capacity to induce neuroinflammation, dysregulate neurotransmitter systems, and alter in monoamine transporters and receptors. Additionally, it discusses the rewarding and abuse potential of synthetic cathinones drawing from findings obtained through various preclinical animal models, contextualized with other classical psychostimulants. The review also offers an overview of current abuse trends of synthetic cathinones on the illicit drug market, specifying the aspects covered, and underscores the risks they pose to public health.

Considering the aging society and budget constraints, a strategy for reforming public transportation welfare policies is essential for sustainability. Among the various transportation welfare policies, fare discount policies are provided to specific age groups, and most countries offer benefits to several public transportation. South Korea provides a fare-free policy limited to subways, and the need for policy modification is emerging due to sustainability problems caused by an aging society. Hence, the scope of the policy should be expanded to all travel modes, but the discount rate should be reduced, or the target group should be reduced in consideration of the budget. This study proposes a travel mode to focus on by city through the preference of the elderly. The latent class model is employed to classfy stated preference data collected from the survey. The estimation results show a significant preference heterogeneity depending on the level of subway supply by region, and a policy focused on subways would be more reasonable in cities with sufficient subway infrastructure. Hence, regarding sustainability, it may be more appropriate to focus on specific means than to provide the same discount policy for all public transport.

The advent of deep learning has completely reshaped our world. Now, our daily life is fulfilled with many well-known applications that adopt deep learning techniques, such as self-driving cars and face recognition. Furthermore, robotics developed more forms of technology which share the same principle with face recognition, such as hand pose recognition and fingerprint recognition. Image recognition technology requires a huge database and various learning algorithms, such as convolutional neural network and recurrent neural network, that requires lots of computational power, such as CPUs and GPUs. Thus, clients could not be satisfied with the computational resource of the local machine. The cloud resource platform emerged at a historic moment. Docker containers play a significant role of microservices-based applications in the next generation. However, it could not guarantee the quality of service. From clients’ perspective, they have to balance the budget and quality of experiences (e.g. response time). The budget leans on individual business owners and the required Quality of Experience (QoE) depends on usage scenarios of different applications, for instance, an autonomous vehicle requires real-time response, but, unlocking your smartphone can tolerate delays. Plenty of on-going projects developed user-oriented optimization resource allocation to improve the quality of the service. Considering the users’ specifications, including accelerating the training process and specifying the quality of experience, this thesis proposes two differentiate containers scheduling for deep learning applications: TRADL and DQoES .

The International Health Regulations (2005) promote national capacity in core institutions so countries can better detect, respond to and recover from public health emergencies. In accordance with the ‘all hazards’ approach to public health risk, this systematic review examines poisoning and toxic exposures in Myanmar. A systematic literature search was undertaken to find articles pertaining to poisoning in Myanmar published between 1998 and 2020. A number of poisoning risks are identified in this review including snakebites, heavy metals, drugs of abuse, agro-chemicals and traditional medicine. Patterns of poisoning presented in the literature diverge from poisoning priorities reported in other lower-middle income countries in the region. The expe-rience of professionals working in a Yangon-based poison treatment unit indicates that frequently observed poisoning as a result of substances including pharmaceuticals, methanol, and petroleum products were absent from the literature. Other notable gaps in the available research include assessments of the public health burden of poisoning through self-harm, household exposures to chemicals, paediatric risk and women’s occupational risk of poisoning. There is a limited amount of research available on poisoning outcomes and routes of exposure in Myanmar. Further inves-tigation and research is warranted to provide a more complete assessment of poisoning risk and incidence.

Various methods including electrochemical purification, chemical precipitation, solvent extraction, and ion-exchange resins, have maturely been used for removal of copper from nickel anolyte. Interestingly, these approaches of copper removal from nickel anolyte by precipitation are well used as the primary industrial method in nickel production again. However, these methods suffer from several severe drawbacks in industrial practices. One is that a small amount of nickel precipitates with copper in slags，resulting in slag treatment difficulties. Second, this process requires an extremely high activity of the sulfide-based copper removal agents which results in high production costs; the short storage period of the copper removal agent is another drawback of this method. These have been the key challenges in the smelting process of nickel. Herein, we present a comprehensive review of the nickel removal methods used for nickel anolyte purification, electrochemical purification, chemical precipitation, solvent extraction, and ionexchange resins. The advantages and feasibilities of each technique in industrial applications are also explored and analyzed. Finally, we demonstrate that ion-exchange resin-based extraction method can pave a new path for metallurgical research on nickel.

Because only two variables are needed to characterize a simple thermodynamic system in equilibrium, any such system is constrained on a 2D manifold. Of particular interest are the exact 1-forms on the cotangent space of that manifold, since the integral of exact 1-forms is path-independent, a crucial property satisfied by state variables such as internal energy dE and entropy dS. Our prior work [1] shows that given an appropriate language of vector calculus, a machine can re-discover the Maxwell equations and the incompressible Navier-Stokes equations from data. In this paper, We enhance this language by including differential forms and show that machines can re-discover the equation for entropy dS given data. Since entropy appears in various fields of science in different guises, a potential extension of this work is to use the machinery developed in this paper to let machines discover the expressions for entropy from data in fields other than classical thermodynamics.

Abstract: Background: Stigma in health can result in a broad range of vulnerabilities and risk for patients and healthcare providers. The media plays a role in people’s understanding of health and stigma is socially constructed through many communication channels including via media framing. Among health issues that were affected by stigma recently were the Monkeypox and Covid-19. Objectives: This research aims to examine how The Washington Post framed stigma around mon-keypox and COVID-19. Guided by the framing theory and stigma theory, online news coverage for monkeypox and COVID-19 were analyzed to understand the construction of social stigma through the media reporting. Methods: This research employed a qualitative content analysis to compare news framing in The Washington Post online news regarding monkeypox and COVID-19. Results: Based on endemic, reassurance, and sexual transmission frames, the The Washington Post predominantly defined Africa as the source of the disease, blames gay communities, and empha-sizes no need to worry about the spread of the monkeypox virus. For the COVID-19 coverage, The Washington Post described China as the source of the coronavirus and constructs the image of panic towards the spread of the virus. Conclusions: The shifts in stigma discourse essentially manifest racism, xenophobia, and sexism in public health. This research affirms that the media reinforces stigma phenomenon in health through framing and offers constructive suggestions for mitigating this issue.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

Bright morning light (BML) entrains the body clock, modulates circadian rhythm, and improves sleep-wake disturbances. However, its impact on the autonomic nervous system (ANS) at night remains unclear. Hence, we investigated the effects of BML exposure on activities of the parasympathetic nervous system (PSNS) and sympathetic nervous system (SNS) at night. This non-randomized controlled pilot study included participants ≥60 years, diagnosed with a type of dementia or cognitive disorder. We excluded participants with pacemakers. The treatment group received 2500 lx BML, whereas the control group received approximately 200 lx of general lighting. We measured the heart rate variability to quantify ANS activity. The treatment group displayed significantly increased high-frequency (HF) power (Roy's largest root=2.44; P<.01) and insignificantly decreased normalized low-frequency (LF%) power. The corresponding low-frequency/high-frequency ratio (LF/HF), insignificant decrease, and cognitive function were correlated with PSNS activity (Roy's largest root=3.92; P<.01), which is effective for moderate dementia. BML exposure reduced SNS activity and enhanced PSNS activity at night, which consequently affected cognitive function. Furthermore, the light washout intervention markedly increased SNS activity at night. BML therapy may be a useful clinical tool for alleviating the deterioration of cognitive function.

Levels of synthetic musk fragrances (SMFs) and various personal care products (PCPs) were measured in the Han River and its tributaries in Seoul, Korea. The most abundant SMF in all river and PCP samples was 4,6,6,7,8,8-hexamethyl-1,3,4,7-tetrahydrocyclopenta[g]isochromene (HHCB), followed by 1-(3,5,5,6,8,8-hexamethyl-6,7-dihydronaphthalen-2-yl)ethanone (AHTN), musk ketone (MK), and 1,1,2,3,3-pentamethyl-2,5,6,7-tetrahydroinden-4-one (DPMI). There was a significant correlation between the SMF concentration in the PCPs and the Han River samples. Moving from upstream to downstream in the Han River, the median SMF concentration was 6.756, 2.945, 0.304, and 0.141 μg/L in the sewage treatment plant (STP) influent, effluent, tributaries, and mainstream, respectively, implying that effective SMF removal was achieved during the sewage treatment process, followed by dilution in the receiving water. Four STPs using advanced biological treatment processes had removal efficiencies of 55.8%, 50.6%, 43.3% for HHCB, AHTN, and MK, respectively. The highest SMF concentrations in the tributaries were observed at locations close to the STPs. Our study confirmed that the main source of SMFs in the receiving water were sewage effluent containing untreated SMFs, which are largely originated from household PCPs, especially hair care products (e.g., shampoo) and perfumes.

Prediction of protein-ligand binding affinities is crucial for computational drug discovery. A number of deep learning approaches have been developed in recent years to improve the accuracy of such affinity prediction. While the predicting power of these systems have advanced to some degrees depending on the dataset used for model training and testing, the effects of the quality and quantity of the underlying data have not been thoroughly examined. In this study, we employed erroneous datasets and data subsets of different sizes, created from one of the largest databases of experimental binding affinities, to train and evaluate a deep learning system based on convolutional neural networks. Our results show that data quality and quantity do have significant impacts on the prediction performance of trained models. Depending on the variations in data quality and quantity, the performance discrepancies could be comparable to or even larger than those observed among different deep learning approaches. In particular, the presence of proteins during model training leads to a dramatic increase in prediction accuracy. This implies that continued accumulation of high-quality affinity data, especially for new protein targets, is indispensable for improving deep learning models to better predict protein-ligand binding affinities.

In this work, we report on the first attempt using size-controlled ZnO nanoparticles (NPs) to analyze role of thioacetamide (TAA) in forming ZnS nanostructures from ZnO. The size-controlled B(blue)_, G(green)_, Y(yellow)_ZnO QDs, and NC (nanocrystalline)_ZnO NPs were synthesized by sol-gel process as well as hydrothermal method, respectively and then reacted with an ethanolic TAA solution as sulfur source. After reacting with TAA, the formation of ZnS QDs was observed over time. The chemical reactions were identified using X-ray diffraction (XRD), Transmission Electron Microscope (TEM), UV-vis spectroscopy, and Photoluminescence (PL). All results indicate that ZnS formation is due to direct crystal growth and/or chemical conversion of ZnO to ZnS. Our results enable a broader understanding of the synthetic mechanisms involved in the use of TAA as a sulfur source in forming ZnS nanostructures from ZnO.

Urbanization and industrialization processes in Mongolia have been significant and rapid for the last half-century. During this period, changes in political and economic systems, growth in the population, and the occasional harsh climate conditions were subject to fluctuations in the natural resource usage. The total Ecological Footprint (EF) in Mongolia has increased from 6.8 million global hectares (gha) in 1961 to 14.6 million gha in 2012. However, Biocapacity (BC) has decreased from 50.6 million gha in 1961 to 39.0 million gha in 2012. The study shows that grazing land Footprint and carbon uptake land Footprint are the two major contributors of the recent intensified use of biological resources. To ensure stable economic development and sustainable use of natural resources, environmental planning is required to consider both the population’s pressure on the environment and the ecosystem’s regeneration capacity, simultaneously. We have proposed a few possible strategies for sustainable utilization of grazing land Footprint and carbon Footprint. For grazing land Footprint, efficient management of both herding practice and number of animals should be considered. In case of carbon Footprint, it is estimated that with the improved combustion efficiencies of coal-based power plants and the maximum use of renewable energy, carbon dioxide (CO₂) emissions in Mongolia can be reduced up to 30% compared to the base line business as usual case in 2030.

In this paper, we investigate the new degenerate Daehee polynomials and numbers which are called the degenerate Daehee polynomials of the second kind, and derive some new and interesting identities and properties of those polynomials.

The research examines the relationship between self-rated health situation and personal percep-tion of heat waves, and how social linkage of communities would be a moderator variable in residents’ perception of heat waves in Taiwan. This study uses the questionnaire conducted by Sinica “Responsive Capacity under Heat Wave: The Perspectives of the Locals”(2019), using OLS method for estimating the unknown parameters in multiple regression model. The author finds that the correlation of self-rated health situation and perception toward heat is significantly posi-tive. Also, social linkage in communities affects strongly as a moderator variable: While the sat-isfaction to with their community could reduce negative reaction to heat, contacts with neighbors could increase possibility people feel uncomfortable in high-temperature situation. This study ex-hibits the effects of social environment on community, and expects further related researches or practices to strengthen capability to resist heat wavesƒ for Taiwanese residents.

This retrospective study aimed to assess coronary artery calcium (CAC) progression in serial computed tomography measurements according to risk factor changes. In 448 asymptomatic adults who underwent CAC measurements with more than one-year intervals, CAC progression was assessed according to age, sex, variable traditional risk factors (diabetes mellitus, hypertension, hyperlipidemia, and smoking), and initial CAC score (0, 0.1–100, and &gt;100). Univariate and multivariate logistic regression analyses were assessed for independent predictors of rapid CAC progression (△CAC/year&gt;20). During the 3.5-year follow-up, coronary artery calcifications occurred in 43 (12.8%) of 336 individuals with an initial CAC score of zero. Of 112 individuals with initial CAC presence, 60 (53.6%) had △CAC/year&gt;20. Age, male sex, body mass index, and all risk factors were significantly associated with △CAC/year&gt;20, but recently diagnosed hypertension (odds ratio [OR], 11.3) and initial CAC score (OR, 1.05) were significant independent predictors in multivariate regression analyses. CAC progression was affected by demographic and traditional risk factors, but adjusting for these factors, recently diagnosed hypertension and initial CAC score were the most influential factors for rapid CAC progression. These findings suggest that patients with higher initial CAC scores may benefit from more frequent follow-up scans and checks regarding risk factor changes.

In this study, the microbial community during the barley yeast fermentation of stevia leaves and its correlation with antioxidant, antiobesity, and anti-inflammatory properties, as well as metabolites, were investigated using UPLC-Q-TOF-MS. Stevia was fermented using commercial TSB media (TSB 1, TSB 2, and TSB 3) and sucrose (Sucrose 1, Sucrose 3, and Sucrose 3) for 1, 3, and 5 days, respectively. Stevia ferments showed higher DPPH and ABTS radical scavenging capacity compared to samples incubated with sucrose for 5 days, and all six ferments inhibited nitric oxide production in a concentration-dependent manner in LPS-induced mouse macrophages. Furthermore, UPLC-QTOF-MS analysis identified 23 related substances, including 10 terpenoids, including rubusoside, steviolbioside, and rebadioside derivatives; dulcoside A; and phlomisoside II, which are indicators of stevia, as well as five flavonoids, four phenolic acids, and four fatty acids. We also identified the microbial community during fermentation via the next-generation sequencing of the 16S rRNA gene for bacteria and the internal transcribed spacer (ITS) gene for fungi. The results showed that TSB 1 and Sucrose 1 ferments were dominated by the pathogens Enterococcus hirae (58.93%) and Cronobacter sakazakii (80.92%), while samples fermented for more than 3 days were pathogen-free and dominated by lactic acid bacteria such as Pediococcus stilesii (73.37%). Microbial community analysis using the ITS region showed that Saccharomycopsis fibuligera, classified as a yeast rather than a mold, dominated the stevia fermentation regardless of the fermentation duration. In particular, the microbial community of the fermentation with a sugar solution was dominated by S. fibuligera by more than 99% throughout the fermentation periods of 1, 3, and 5 days. Finally, to apply the stevia ferments topically to human skin, skin irritation tests were performed on 30 volunteers. The results showed that the highly concentrated extracts (1 mg/mL) of all six stevia ferments were hypoallergenic. Taken together, these findings suggest that brewer's yeast fermented from stevia leaves with a sugar solution offers promise as a natural ingredient for use in functional foods and cosmetics.

To clarify whether cryptochrome contributes to stem elongation and flowering promoted by blue lights associated with low phytochrome activity, wild-type Arabidopsis was compared with its cryptochrome-deficient mutants and cryptochrome-overexpressing transgenic plants. Results indicated that the promotion effects were mainly related to low CRY1 activity, despite partial involvement of high-activity CRY2.

Geniposide is a major ingredient in the herb gardenia, and this study investigated effects of geniposide on lipopolysaccharide-stimulated macrophages (RAW 264.7). Griess reagent assay, Fluo-4 calcium assay, dihydrorhodamine 123 assay, multiplex cytokine assay, quantitative RT-PCR, and flow cytometry assay were done using RAW 264.7. Data showed that geniposide at concentrations of 10, 25, and 50 μM reduced significantly levels of nitric oxide, intracellular Ca2+, and hydrogen peroxide in lipopolysaccharide-stimulated RAW 264.7. Multiplex cytokine assay represented geniposide at concentrations of 10, 25, and 50 μM meaningfully suppressed levels of IL-6, G-CSF, MCP-1 and MIP-1α in RAW 264.7 provoked by lipopolysaccharide; additionally, geniposide at concentrations of 25 and 50 μM meaningfully suppressed levels of TNF-α, IP-10, GM-CSF, and MIP-1β. Flow cytometry assay represented that geniposide reduces significantly the level of phosphorylated P38 MAPK in RAW 264.7 provoked by lipopolysaccharide. Geniposide meaningfully suppressed lipopolysaccharide-induced transcription of inflammatory target genes such as Chop, Jak2, Fas, c-Jun, c-Fos, Stat3, Nos2, Ptgs2, Gadd34, Asc, Xbp1, Nlrp3, and Par-2. Taken together, geniposide exerts anti-inflammatory effects in lipopolysaccharide-stimulated macrophages via calcium-P38 MAPK pathway.

Aging is associated with muscle atrophy and fatty infiltration of skeletal muscle. The multifidus muscle stabilizes the lumbar spine and undergoes adipose accumulation with age, leading to functional decline in the elderly. Therefore, quantitative assessment of the multifidus muscle can be beneficial for the elderly when formulating treatment strategies and reducing future complications. Fifty-seven patients (mean age, 73.89 ± 6.09; 23 male patients) who underwent lumbar Magnetic resonance imaging (MRI) were prospectively recruited. The cross-sectional area (CSA) of the multifidus from the L2-S1 level and the CSA of the L4-5 level psoas muscle were measured. The functional CSA (fCSA) of the multifidus muscle was measured by excluding the fat infiltration area from the multifidus CSA. The CSA to fCSA ratio was obtained by multiplying 100 by the value obtained by dividing CSA by the fCSA. Pfrrmann classification was used to evaluate the degree of disc degeneration. The functional disability measurements were the Short Physical Performance Battery (SPPB), Berg Balance Scale (BBS), grip strength, and functional reach test (FRT). Pearson's correlation analysis was used to examine the relationship between the functional disability measurements and the multifidus muscle. The CSA to fCSA ratio value was relatively constant at each spine level and showed a significant correlation with the SPPB, grip strength, FRT, and psoas index (p&lt;0.05). However, degree of disc and multifidus muscle degeneration were not statistically significant. So, age-related changes play a significant role in developing back muscle fatty infiltration than disc dgeneration. Moreover, Grip strength showed a stronger relationship with the quality of the multifidus muscle than other functional disability measurements.

The betel nut chewing habit of taxi drivers has shown that can promote companionship, relaxation, and emotional stability at work. 19.3% of betel nut behaviors are instigated by an invitation among drivers to engage in the habit. The objective of this study was to explore the impact of social learning, subjective norm, and self-efficacy on betel nut chewing in taxi drivers in Taiwan. We conducted a cross-sectional study on taxis’ driver of betel nut behaviour and measured their evaluations of its consequences using a self-report questionnaire. Other variables include socio-demographic characteristics and chewing-related experience. The overall variance is 44.5% in socio-demographic variable, social learning, self-efficacy, and subjective norm. Results show that the variables of affected betel nut chewing behavior, driving years has the strongest influence, followed by learning about betel nut from the media, relatives, and friends, and education level, which positively affect betel nut chewing behavior. Findings indicated that education related to quitting betel nut chewing, significant others, and rules of the taxi fleet are adopted to design a plan for quitting betel chewing to reduce the positive expectations of taxi drivers for betel nut chewing and decrease their betel nut chewing behavior.

Our previous study demonstrated that mesenchymal stem/stromal cells (MSCs) induced the differentiation of myeloid-derived suppressor cells (MDSCs) in the bone marrow (BM) under inflammatory conditions. In the present study, we aimed to explore the signaling pathway in BM cells responsible for MDSC generation. RNA-seq revealed that the mitogen-activated protein kinase (MAPK) pathways, among biochemical pathways, exhibited the highest number of differentially expressed genes in BM cells with MSC coculture relative to those without. Western blot confirmed strong phosphorylation of c-Jun N-terminal kinase (JNK) in BM cells cocultured with MSCs under GM-CSF stimulation, whereas p38 kinase activation remained unaltered by MSCs. Inhibition of JNK by SP600125 significantly abolished the expression of Arg1 and Nos2, the hallmark genes of MDSCs, as well as Hif1α, a molecule mediating monocyte functional re-programming into suppressive phenotype, in MSC-cocultured BM cells, while increasing TNF-α in response to lipopolysaccharides stimulation. Furthermore, JNK inhibition markedly abrogated the effect of MSCs on the production of TGF-β1, TGF-β2 and IL-10 in BM cells. These results suggest that MSCs induce MDSC differentiation in BM during inflammation, at least in part, through the activation of the JNK MAPK signaling pathway.

A flexible structure is applied to improve the lubrication performance of a misaligned journal bearing. The journal bearing is representative sliding bearing and there are damages due to metal-to-metal contact by misalignment. Since misalignment is an unavoidable phenomenon, a journal bearing with a flexible structure was proposed as a way to improve it. The lubrication characteristics of the bearing are evaluated numerically under steady-state condition. EHL (elastohydrodynamic lubrication) analysis considering elastic deformation was performed. The lubrication performance is compared in accordance with variation of the geometry of the flexible structure and evaluated based on the minimum film thickness. Moreover, the results of the journal bearing with flexible structure are compared with those of the journal bearing without the flexible structure. The flexible structure is then applied in the form of a groove to the area supporting high load on the journal bearing; it is elastically deformed by the generated oil-film pressure, which helps to obscure a larger oil film. Through numerical analysis, it is found that the journal bearing with flexible structure can improve the lubrication performance in the misaligned condition.

As the incidence and prevalence of diabetes increases, intervention through dietary education is becoming more important for diabetes control. This systematic review aimed to confirm the ef-fect of dietary intervention education on diabetes control. The study subjects were type 2 diabet-ic patients, and the main outcome variable was glycosylated hemoglobin level (HbA1c). The target studies were randomized controlled trials. Thirty-six studies were included in the analysis, of which 33 were included in the meta-analysis. The effect size between the dietary education and general intervention, was -0.42 (n=5,639, MD=-0.42; 95% CI -0.53 to -0.31) and was signifi-cantly different (Z=7.73, P<.001). When subgroup analyses were performed following the appli-cation periods, intervention methods, and intervention contents, the mean differences in 4–6-month application, individual education, diet-exercise-psychosocial intervention were -0.51, (n=2,742, 95% CI -0.71 to -0.32), -0.63 (n=627, 95% CI -1.00 to -0.26), and -0.51 (n=3.244, 95% CI -0.71 to -0.32), respectively. Dietary education interventions provided for at least 3 months were highly effective in controlling blood sugar levels. Regarding the education method, individual-ized education was more effective, and for this, contact or non-contact education may be applied. Combining diet, exercise, and psychosocial intervention is more effective than diet education alone.

Embracing innovative digital technologies within educational systems is essential for overcoming challenges in modern learning environments, especially in the post-COVID-19 era. Teaching sustainability management in higher education institutions with innovative digital tools plays a fundamental role in the transition toward sustainable societies. Suitable game design elements play a significant role in facilitating sustainable learning. This study explored the effectiveness of incorporating business simulation games with project-based learning (PBL) in a flipped classroom setting. This approach was adopted within the context of a university cross-border e-commerce course to prepare students for acquiring 21st -century skills as higher-order thinking skills in a rapidly changing educational landscape. A quasi-experimental method was employed, involving a total of 60 university students from China's Zhejiang Province. Participants completed an online questionnaire designed to assess their learning engagement across three dimensions (cognitive, emotional, and behavioral) as well as their higher-order thinking skills (problem-solving, critical thinking, and creativity). The results show that the business simulation games combined with flipped classroom learning had a significantly positive impact on students’ learning outcomes, enhancing their problem-solving, critical thinking, and creative capabilities. Importantly, this approach also improved student engagement and promoted sustainable practices by applying real-life scenarios in an interactive environment. We conclude that business simulation games integrated with project-based learning (PBL) in flipped classroom settings represent a valuable educational approach. This approach not only enhances learning engagement but also fosters the development of higher-order thinking skills, encouraging students to adopt sustainable learning practices.

This study presented a novel and sustainable method for producing chitin nanocrystals (PA-ChNCs) using phosphoric acid hydrolysis. The produced PA-ChNCs were used as stabilizers for Pickering emulsions and their physicochemical properties as well as stabilization mechanisms were systematically investigated. The PA-ChNCs exhibited small particle sizes and high surface areas, enabling an effective adsorption at the oil/water interface, which prevented coalescence in Pickering emulsions. The particle size and surface charge PA-ChNCs were strongly pH-dependent, which were critical factors for stabilizing Pickering emulsions. The study showed that emulsions with higher O:W ratios (50%) exhibited larger droplets but greater viscosity, forming a stable gel-like matrix that was more stable than emulsions with other O:W ratios after storage for 30 days. Emulsions with higher PA-ChNCs concentrations (2.0 wt%) and higher pH values (pH 10) showed small droplets and high viscosity, leading to stable emulsions. This research contributes to the development of sustainable and effective emulsifiers for use in the food industry, making utilization of seafood waste in an eco-friendly manner possible. Overall, this study highlights the potential of using newly developed PA-ChNCs as stabilizers for Pickering emulsions in food products.

Potential breeding habitat of egrets and herons was evaluated using the Maximum Entropy Model (MaxEnt). Model output can help guide management of nuisance egret and heron rookeries in urban forests of Daejeon Metropolitan City, Korea. This study examined 126 locations regarded as breeding sites of egrets and herons at the nationwide census conducted by the National Institute of Environmental Research between 2011 and 2012. In addition, 252 randomly selected locations were used to identify the significant variables among a total of 15 environmental variables within 4 factors (topography, natural environment, distance and climate). Twelve variables were significantly different between the breeding and randomly selected points. The final 10 variables were selected through Pearson’s correlation analysis. Using MaxEnt, breeding area was estimated using the 10 selected variables in Daejeon. The area under the receiver operating characteristic curve (AUC) was 0.950, which was the average value through 10-fold cross-validation to estimate the model reliability. The potential breeding habitat for egrets and herons was estimated to be 106.69 km2 (19.76% of the total area) in Daejeon. Within the estimated potential habitat, 11.82 km2 (12.46%) were less than 50 m from the residential district while 79.85 km2 (88.92%) were more than 50m from the residential district. Discriminative management strategies considering the breeding location of egrets and herons should be applied not only to minimize conflicts with residents, but also to maintain stable egret and heron breeding sites in Daejeon, Korea.

Lymphoma diagnoses in the U.S. are substantial, with an estimated 89,380 new cases in 2023, necessitating innovative treatment approaches. Phase 1 clinical trials play a pivotal role in this context. We developed a binary predictive model to assess trial adherence to expected average durations, analyzing 1,089 completed Phase 1 lymphoma trials from clinicaltrials.gov. Using machine learning, the Random Forest model demonstrated high efficacy with an accuracy of 0.7248 and ROC-AUC of 0.7701 for lymphoma trials. Importantly, this model maintained an accuracy of 0.7405 when applied to lung cancer trials, showcasing its versatility. A key insight is the correlation between higher predicted probabilities and extended trial durations, offering nuanced insights beyond binary predictions. Our research contributes to enhanced clinical research planning and potential improvements in patient outcomes in oncology.

A human eye has about 120 million rod cells and 6 million cone cells. This huge number of light sensing cells inside a human eye will continuously produce a huge quantity of visual signals which flow into a human brain for daily processing. However, the real-time processing of these visual signals does not cause any fatigue to a human brain. This fact tells us the truth which is to say that human-like vision processes do not rely on complicated formulas to compute depth, displacement, and colors, etc. On the other hand, a human eye is like a PTZ camera. Here, PTZ stands for pan, tilt and zoom. We all know that in computer vision, each set of PTZ parameters (i.e., coefficients of pan, tilt and zoom) requires a dedicated calibration to determine a camera’s projection matrix. Since there is an infinite number of PTZ parameters which could be produced by a human eye, it is unlikely that a human brain stores an infinite number of calibration matrices for each human eye. Therefore, it is an interesting question for us to answer, which is to say whether simpler formulas of computing depth and displacement exist or not. Moreover, these formulas must be calibration friendly (i.e., easy process on the fly or on the go). In this paper, we disclose an important discovery of a new solution to 3D projection in a human-like binocular vision system. The purpose of doing 3D projection in binocular vision is to undertake forward and inverse transformations (or mappings) between coordinates in 2D digital images and coordinates in a 3D analogue scene. The formulas underlying the new solution are accurate, easily computable, easily tunable (i.e., to be calibrated on the fly or on the go) and could be easily implemented by a neural system (i.e., a network of neurons). Experimental results have validated the discovered formulas.

Visual signals are the upmost important source for robots, vehicles or machines to achieve human-like intelligence. Human beings heavily depend on binocular vision to understand the dynamically changing world. Similarly, intelligent robots or machines must also have the innate capabilities of perceiving knowledge from visual signals. Until today, one of the biggest challenges faced by intelligent robots or machines is the matching in stereovision. In this paper, we present the details of a new principle toward achieving a robust matching solution which leverages on the use and integration of top-down image sampling strategy, hybrid feature extraction, and RCE neural network for incremental learning (i.e., cognition) as well as robust match-maker (i.e., recognition). A preliminary version of the proposed solution has been implemented and tested with data from Maritime RobotX Challenge (www.robotx.org). The contribution of this paper is to attract more research interest and effort toward this new direction which may eventually lead to the development of robust solutions expected by future stereovision systems in intelligent robots, vehicles and machines.

When following a prescribed route, we need to decide at each intersection which way to proceed. The present work addressed several factors that might influence the difficulty of this decision making process. Participants repeatedly followed a route through a virtual maze with twelve or eighteen intersections, and with two or three choices per intersection. One group performed task S, which promoted decision making by the serial order strategy since all intersections looked alike. Another group performed task SA, which allowed the use of the serial order and the associative cue strategy since unique visual cues were presented at each intersection. We found that in both tasks, participants were more accurate in making decisions on routes with twelve rather than eighteen intersections, and more accurate by a similar amount on routes with two rather than three choices. Reaction time in task SA was reciprocal to accuracy; reaction time in task S was generally lower and route-independent. Accuracy in task SA was similar for participants who experienced smooth transport across intersections and those who experienced abrupt transport, while accuracy in task S was lower for participants who experienced smooth rather than abrupt transport across intersections. We conclude that the number of intersections and the number of choices were equivalent determinants of route following difficulty. We further conclude that optic flow during turns at intersections interfered with anticipatory decision making in task S; hence natural (smooth) transport across intersections did not enhance route following performance.

Additive manufacturing (AM) has revolutionized the field of biopolymers by providing a range of opportunities to create complex and intricate structures. Here we provide an overview of developments in biopolymer AM, first in the context of how natural systems have impacted the synthetic processes of AM, and secondly in the context of how synthetically derived structures can be used for biomedical applications. In particular, we explore the range of biopolymers developed for AM, AM techniques for biopolymers, and potential biocompatible medical applications with a focus on four categories of tissue in the human body: skin, bone, heart, and nerve. Despite the current challenges of the technology, exciting results in tissue regeneration, synthetic replacements for natural grafts, and complex dynamic organoids have already come to pass - with many more possible in the future.