Transmission electron microscopy methods were used to analyze the cementite substructure in the head of special-purpose long rails of DT400IK category made of hypereutectoid steel after long-term operation on an experimental track on the Russian Railways ring (the passed tonnage is 187 million tonnes). It is noted that the study of various aspects of cementite – its structure, morphology, chemical composition, crystal lattice defects is relevant. The steel structure is represented by three morphological components at a distance of 10 mm from the sample surface: lamellar perlite, fractured and fragmented perlite. The volume fraction of lamellar perlite in the material is 65%. It is shown that after operation, the cementite plates are bent and separated by ferrite bridges. In the plates of ferrite and cementite, a dislocation substructure is formed which is of chaotically distributed and network type in ferrite and of ordered type in cementite. An increased density of dislocations at ferrite-cementite interfaces compared to the volume of ferrite plates was noted. Two possible mechanisms of deformation transformation of lamellar perlite grains are indicated: fracture of cementite plates and carbon pulling out from the lattice of the carbide phase. It is indicated that in the dissolution of cementite plates, the interfacial boundaries “α-phase-cementite” play an important role. The removal of carbon from cementite plates occurs most intensively near defects in ferrite and cementite. The formed nanosized particles of tertiary cementite are unevenly distributed in the ferrite plates, most of them are observed at the locations of ferrite subgrains and interfacial boundaries. This results in non-uniform diffraction contrast in dark-field images of cementite plates. Nanosized particles of cementite can be taken out into the interlamellar space of pearlite colonies in the process of dislocation slip, or they are formed as a result of deformation decomposition, which is less likely. Fragmentation of ferrite and cementite plates is revealed and azimuthal components of total misorientation angles are estimated. The mechanisms of mass transfer of carbon atoms over interstitial sites, deformation vacancies, dislocation tubes, grain boundaries and fragments are considered. According to all the established patterns of the cementite substructure transformation, a comparison with the results for rails made of hypoeutectoid steel was performed.

This paper secures the analytical soliton solutions of the perturbed NLSE gives to (1). The existence criteria have been demonstrated and the wave speed of the soliton befall out. To achieve all the results obtained we used the mathematical technique. In view of the results obtained, some new additional one have been reported in left-handed metamaterials.

We apply utilized the extended form of the auxiliary equation method to obtain extensively reliable exact travelling wave solutions of perturbed Gerdjikov–Ivanov equation (GIE) that is widely used as a model in the field theory of quanta and non-linear optics. The method is based on a simple first order second degree ODE. The new form of the approach gives more solutions to the governing equation efficiently.

In recent years, there has been an increasing demand for personalized experiences in various domains, including the cultural and educational sectors. Museums, as custodians of art, history, and scientific knowledge, are seeking innovative ways to engage their visitors and provide tailored content that enhances their understanding and appreciation of the exhibits. This article presents ExhibitXplorer, a distributed architecture service that leverages geofencing, artificial intelligence, and microservices to enable personalized content delivery in museums. By combining implicit and explicit segmentation of museum visitors and utilizing the GPT API for content generation, ExhibitXplorer offers a dynamic experience to different visitor segments, including researchers, students, casual visitors, and children. The system utilizes push notifications triggered by visitor location changes, allowing seamless delivery of personalized information both indoors and outdoors. Tests were conducted to evaluate the user experience of visitors to an outdoor ethnographic museum. The results showed that 55% of the test participants were satisfied and 45% very satisfied with the way personalized content was delivered.

An approach to the implementation of neural network for real-time cryptographic data protection with symmetric keys oriented on embedded systems is presented. This approach is valuable especially for onboard communication systems in unmanned aerial vehicles (UAV) because of suitability to hardware implementation. In this study we evaluate the possibility to build such a system in hardware implementation at FPGA. The proposed integrated neural network approach for real-time cryptographic data protection was based on theoretical foundations of neural network cryptographic data protection, new algorithms and structures of neural network data encryption and decryption, modern hardware components with programmable structure. The development and implementation of the on-board neural network system for cryptographic data protection in real-time are based on the following principles: variable composition of equipment; modularity; conveyorization and spatial parallelism; hardware and software modification and making them suitable for data encryption and decryption. The tabular-algorithmic method for calculation of the scalar product has been improved that makes it possible to perform fast calculation of the scalar product of fixed-point and floating-point input data by bringing them to the largest common order of weights and forming tables of macro-partial products. Components of neural network cryptographic data encryption and decryption have been developed on the processor core supplemented by specialized scalar product calculation modules. The specialized hardware for neural network cryptographic data encryption was developed using VHDL for equipment programming in the Quartus II development environment ver. 13.1 and the appropriate libraries, and implemented on the basis of the FPGA EP3C16F484C6 Cyclone III family.

The neural network technology for real-time cryptographic data protection with symmetric keys (masking codes, neural network architecture and weights matrix) for unmanned aerial vehicles (UAV) onboard communication systems has been developed. It provides hardware and software implementation with high technical and operational characteristics. The development of neural network technology for real-time cryptographic data protection was performed using an integrated approach based on theoretical foundations of neural network cryptographic data protection, new algorithms and structures of neural network data encryption and decryption, modern element base with the possibility of programming for the structure, and computer-aided design of hardware and software tools. The development and implementation of the on-board system of neural network cryptographic data protection in real-time are based on the following principles: variable composition of equipment; modularity; conveyorization and spatial parallelism; specialization and adaptation of hardware and software to data encryption and decryption. The tabular-algorithmic method of calculating the scalar product has been improved, it provides fast calculation of the scalar product of input data for both fixed and floating-point by bringing to the largest common order of weights and forming tables of macro-partial products for them. Components of neural network cryptographic data encryption and decryption have been developed on the processor core supplemented by specialized scalar product calculation modules. The specialized hardware for neural network cryptographic data encryption was developed using VHDL for equipment programming in the Quartus II development environment ver. 13.1 and the appropriate libraries, and implemented on the basis of the FPGA EP3C16F484C6 Cyclone III family.

In this paper, the linear nonequilibrium thermodynamic approach is used to analyze energy processes in the wind energy conversion system (WECS), with a directly connected vertical axis wind turbine (VAWT) and vector controlled permanent magnet synchronous generator (PMSG). Both elements are considered as linear universal energy converters (EC) linearized at the points of the given range of common to VAWT and PMSG angular velocity. The dependences on the angular velocity of the coupling coefficients between the ECs input and output and the dimensionless parameters of their operating modes were received. This allows for choosing the optimal points of ECs operation according to the specified criteria and obtaining indicators of their maximum efficiency. To assess the quality of the cascade connection of two ECs, the appropriate coefficient was introduced, the dimensionless parameters and characteristics of the equivalent EC were obtained, and the conditions of its maximum efficiency were determined. Analysis of the VAWT-PMSG connection quality showed reserves for improving WECS efficiency. The impact of VAWT and PMSG variable parameters on the quality of this connection is studied, and further research directions are shown. The proposed thermodynamic approach allows an effective search for solutions for the efficiency improvement of various systems with energy transfer and transformation.

The research presents the Methodology of Improving the Accuracy in Text Classification in Light of Modelling the Latent Semantic Relations (LSR). The aim of this Methodology is to find the ways of eliminating the Limitations of Discriminant and Probabilistic methods for LSR revealing and customizing the Text Classification Process to the more accurate recognition of the text tonality. This aim should be achieved by using the knowledge about the text’s Hierarchical Semantic Context in the form of Corpora-based Hierarchical Sentiment Dictionary. The main scientific contribution of this research is the following set of approaches to improve the qualitative characteristics of Text Classification process: combination of the Discriminant and Probabilistic methods allowing to decrease the influences of the Limitations of these methods on the LSR revealing process; considering each document as a complex structure allowing to estimate documents integrally by separated classification of topically completed textual component (paragraphs); taking into account the features of Argumentative type of documents (Reviews) allowing to use the author’s subjective evaluation of text tonality for development the Text Classification methodology. Tonality, expressed by the Review’s author, has a significant, but not critical, effect on the qualitative indicators of Sentiment Recognition.

OSI model used to be common network model for years. In the case of ad hoc networks with dynamic topology and difficult radio communications conditions, gradual departure is happening from the classical kind of OSI network model with a clear delineation of layers (physical, channel, network, transport, application) to the cross-layer approach. The layers of the network model in ad hoc networks strongly influence each other. Thus, the cross-layer approach can improve the performance of an ad hoc network by jointly developing protocols using interaction and collaborative optimisation of multiple layers. The existing cross-layer methods classification is too complicated, because it’s based on the whole manifold of network model layers combinations, regardless their importance. In this work, we review ad hoc networks cross-layer methods, propose the new useful classification of cross-layer methods, and show future research directions in ad hoc networks cross-layer methods development. The proposed classification can help to simplify the goal-oriented cross-layer protocol development.

Two Iron Age settlements, Tuzusai and Taldy Bulak 2 (ca. 500 BCE to 1 CE), located in Southeastern Kazakhstan on the Talgar alluvial fan north of the Tian Shan range, have yielded a small collection of bone, antler/horn, bronze, and stone artifacts with affinity to nomadic art of the first millennium BCE. Both settlements date within the period of late Saka culture. Two pieces have decorative ornamentations with zoomorphic imagery: a small carved fragment of a with carved images of a wing and an ear and a perforated bone disk with the carving of three birds’ heads. The other artifacts include objects associated with Saka weaponry or nomadic economy such as the two antler/horn psalia (cheek pieces) and a bronze amulet. A carnelian bead will also be described as an imported object. These special finds are found on the occupation floors of mud brick houses and pit houses of settlements, not in grave or burial contexts. The objects are placed in stratigraphic sequence in the settlement sites. Then the method for placing these objects within the chronological framework of “animal-style art” is through comparisons with similar objects found throughout Eurasia—a method used in Soviet and Post-Soviet archaeology. The results show that functional and stylistic elements of the six objects indicate that the Talgar settlements were part of a larger world-system of trade and communication along the early Silk Route(s).

In this paper, the authors consider the influence of the type of power supply and the internal parameters of the DC-DC converter on the stability of the system at constant power load. The stability of the system under consideration is important in the design and development of the power supply system for an autonomous consumer. Such a typical system can be a DC microgrid. In the work, when analyzing the stability of the system, the power source is not considered an ideal voltage source, but the active-inductive nature of the voltage source is taken into account, which is equivalent to using a synchronous machine with permanent magnets. The Rauss-Hurwitz algebraic criterion was used as a criterion for analyzing the stability of the system. This will make it possible to build and analyze the areas and boundaries of the system's stability. As a result, the areas and boundaries of the stability of the system were presented. The general trend towards the behavior of the zone of instability of the system was given. At the same time, dependences describing the boundaries of instability are presented, which are combinations of parameters of the DC-DC converter, beyond which the system becomes unstable. The presented definitions of the instability limits can be used as a corrective device of the control system to ensure the stability of the system in the upper limits of the power consumption.

Recent climatic disasters (dzudzs) and uncontrolled massive breeding endangered valuable ge-netic resources of Mongolian goats labored by five thousand years of evolution in extremes of Al-tai mountains and Gobi deserts. Meanwhile, Mongolian goats has never been characterized by genomic data. We used Illumina Goat SNP50 to investigate phylogenic relationships and genetic risks in 5 local Mongolian populations: Erchim (N=37) from geographically remote Darkhat Valley in the northern mountains, Ulgii Red (N=35) and Dorgon (N=28) from the western mountain region, Buural (N=34) from the western steppe and mountain areas and Gobi Gurvan Saikhan (N=33) from semi-arid steppe area in the South Gobi region. ROH analyses, estimated populations sizes and Fst values showed South Gobi and Darkhat Valley goats to be of a high risk of inbreed-ing that however appear to be of distinct origin (artificial selection vs geographical isolation). In-dices of genetic differentiations between Mongolian goats were relatively low compared to Euro-pean breeds. Meanwhile, we suggest direct comparison is not fully appropriate given that Mongo-lian breeds were not subjected to intense selection. Darkhat Valley goats were clearly differentiat-ed from other Mongolian breeds according to various types of analyses. Phylogenetic relationships within XXX breeds of the rest of the world plotted Mongolian goats between some Russian (Altai, Orenburg) and Chinese populations (Nanjiang and Qinggeli). Thus, present study (i) highlights demographic history Mongolian goats and (ii)provides unified SNP-data called for support deci-sions in conservational genetics. Finally, our work (iii) raises a question of how exactly these data should be compared to make objective choices.

The study considers building a dynamic model of profit maximization for the car-sharing system and its verification on the example of implementing such a system in Astana (Republic of Kazakhstan). The region, bounded by the administrative boundaries of Astana, was divided into subregions by covering the region with regular hexagons placed side by side. A dataset was built with information on 1168 trips to Astana from January to March 2023. The Kepler visualization service constructed maps of the beginning and end of trips in the region and a map of trips binding to the hexagonal grid cells. Each cell of the grid corresponds to a specific sub-region, for which the quantitative parameters necessary for solving the profit maximization problem in the car-sharing system are calculated. Stations with cars will be placed in the cells of the grid, which will be available to car-sharing service customers. Based on the collected data, a dynamic (four periods per day) and static profit maximization model in the car-sharing system was built. Modeling was carried out based on the built models in the example of Astana. It was established that using a dynamic model of profit maximization in the car-sharing system increases the profit by 3.7%.

Abstract: The aim of this study was to identify and quantify polyphenolic compounds in skin extracts from four Bulgarian grape varieties and compare to those of seed extracts. The values of total phenolic contents (TPC), flavonoids, anthocyanins, procyanidins, ascorbic acid in grape skin extracts were determined. The antioxidant capacities of skin extracts were evaluated by DPPH, ABTS, FRAP and CUPRAC methods. The TPC values of skin extracts were 2-3 times lower than those of seed extracts. The significant difference between total parameters values of individual grape varieties were also found. According to the TPC and antioxidant capacity of skin extracts the different grape varieties were in the following order: Marselan ≥ Pinot Noir ˃ Cabernet Sauvignon ˃ Tamyanka. The individual compounds in the grape skin extracts were determined by RP-HPLC and compared with those of seed extracts. The determined composition of skin extracts was significant different from seed extracts composition. Qualitative and quantitative evaluation of the procyanidins and catechins in the skins were carried out. A correlation between phenolic contents, individual composition and antioxidant capacity of different extracts was found. The studied grape extracts have a potential to be applied as natural antioxidants in the pharmaceutical and food industries.

Nanoparticles of graphene and carbon nanotubes are attractive materials for improvement of mechanical and barrier properties and functionality of biodegradable polymers for food packaging applications. However, the increase of the manufacture and consumption increases the probability of exposure of human and environment to such nanomaterials, this rising questions about the risks of nanomaterials since they can be toxic. For a risk assessment, it is crucial to know whether airborne nanoparticles of graphene and carbon nanotubes can be released from nanocomposites into the environment at their end-life, or they remain embedded in the matrix. In this work the release of graphene and carbon nanotubes from the poly(lactic) acid nanocomposite films were studied for the scenarios of: (i) biodegradation of matrix polymer at the disposal of wastes; and (ii) combustion and fire of nanocomposite wastes. Thermogravimetric analysis in air atmosphere, TEM, AFM and SEM were used to verify the release of nanoparticles from nanocomposite films. The three factors model was applied for the quantitative and qualitative risk assessment to the release of graphene and carbon nanotubes from nanocomposite wastes for these scenarios. Safety concern is discussed in respect to the existing regulations for nanowastes stream.

Chymotrypsin is an important proteolytic enzyme in human digestion system that cleaves milk proteins, through hydrolysis reaction, which makes it interesting subject to study activity of milk proteases. In this work, we compared detection of chymotrypsin by spectrophotometric, dynamic light scattering (DLS) and quartz crystal microbalance (QCM) methods and determined the limit of chymotrypsin detection (LOD), 0.15 ± 0.01 nM for spectrophotometric, 0.67 ± 0.05 nM for DLS and 1.40 ± 0.30 nM for QCM methods, respectively. We discuss peculiarities and give perspective for implementation of detection methods and note that while the optical detection methods are simple to implement, the QCM method is more robust for sample preparation. We give an overview on methods and instruments for detection of chymotrypsin and other milk proteases.

The purpose of the present study was to develop an experimental model for studying of the intra-articular knee movements depending on the work of the knee joint and applied muscle groups in isometric stretching conditions with different tens. The experimental procedure includes ultrasound examination of a knee joint after isometric stretching of healthy men (n=32). The changes in millimeters of the distances between the femur and tibia were measured with ultrasound sonographer at three stages. The first stage was performed on ten (n=10) healthy men at five different sitting and upright positions. In the second and third experimental model stages the lower limbs loading was on 22 participants. Our hypothesis which was confirmed, was that as a result of increasing extraloads on the participants back (2, 5, 10, 15, 17, 20 kg), a intra-articular decrease in the femur-tibia cartilage surface distance wiil be observed. The accuracy of the created experimental model was improved over its three stages from 30% to 9%. Quantitative model data can help to create a mathematical model for the mechanical effects during deformation of the knee joint bone cartilage, as well as to outlines the some future tasks: increasing loading weights; enlarge participant groups; comparison men and women; healthy and pathology comparison.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

Запропонована методика спрямована на визначення та прогнозування технічного стану елементів мосту, що може слугувати прогресивним інженерним інструментом для оцінки надійності та довговічності. Розроблено на основі фундаментальних досліджень, які узагальнюють досвід вивчення фізико-механічних і фізико-хімічних властивостей матеріалів мостових конструкцій, що експлуатуються в реальних умовах. Теоретичною основою методики є модель надійності та прогнозування залишкового ресурсу елементів мосту на основі теорії Маркова. Розроблена методика призначена для оцінки технічного стану окремих елементів мосту з подальшою комплексною оцінкою всієї конструкції. За показник технічного стану прийнята надійність при експлуатації. Цей кількісний показник надійності в моделі є критерієм для: оцінки рівня безпеки елементів мосту; ранжування елементів мосту за необхідністю для конкретних видів ремонту, реконструкції або заміни; стратегічне планування витрат на ремонт або реконструкцію в умовах обмеженого фінансування; прогнозування залишкового ресурсу елементів. Для застосування розробленої методики запропоновано алгоритм оцінки та прогнозування технічного стану мостів. Було проведено математичний експеримент розробленої методики, який підтвердив адекватність висунутої гіпотези, тобто використання моделі надійності та прогнозування залишкового ресурсу елементів мосту. По-перше, запропоновано триступеневий механізм уточнення технічного стану мосту, суттєво підвищення точності розрахунків. Тому розроблена методика має практичне значення і може слугувати основою для інформаційно-аналітичних систем управління станом мостів.

This paper investigates reachable set estimation and state-feedback controller design for linear time-delay control system with bounded disturbances. First, by constructing an appropriate Lyapunov-Krasovskii functional, we obtained a delay-dependent condition, which determed the admissible bounding ellipsoid for the reachable set of the system we considered. Then, a sufficient condition in form of liner matrix inequalities is given to solve the problem of controller design with reachable set estimation. Finally, by minimizing the volume of the ellipsoid and solving the liner matrix inequality, we obtain the desired ellipsoid and controller gain. A comparative numerical example is given to verify the usefulness of our result.

The pentose phosphate pathway (PPP) is one of three major pathways involved in glucose metabolism, regulated by glucose-6-phosphate dehydrogenase (G6PD), controlling NADPH formation. NADPH, in turn, regulates the balance of oxidative stress and reactive oxygen species (ROS) levels. G6PD dysfunction, affecting PPP, is implicated in neurological disorders, including epilepsy. However, PPP's role in epileptogenesis and ROS production during epileptic activity remains unclear. To clarify these points, we conducted electrophysiological and imaging analyses on mouse hippocampal brain slices. Using the specific G6PD inhibitor G6PDi-1, we assessed its effects on mouse hippocampal slices, examining intracellular ROS, glucose/oxygen consumption, and ROS production during synaptic stimulation and in the 4AP epilepsy model. G6PDi-1 increased basal intracellular ROS levels and reduced synaptically induced glucose consumption but had no impact on ROS production from synaptic stimulation. In the 4AP model, G6PDi-1 didn't significantly alter spontaneous seizure frequency or H2O2 release amplitude but increased the frequency and peak amplitude of interictal events. These findings suggest that short-term PPP inhibition has a minimal impact on synaptic circuit activity.

This paper discusses the preliminary results of archaeological surveys conducted in the Juuku Region of north-central Kyrgyzstan on the south side of Lake Issyk kul. Our goal was to document ancient and contemporary agropastoral systems over a four millenia time period. During the surveys about 350 loci were identified as settlements, burial mounds, graves, single artifact finds, and artifact scatters (ceramic). The areas of Juuku Valley survey included two discrete polygons: Polygon 1, Lower Juuku at 1750 to 1950 m asl in elevation and Polygon 2, Chak Juuku or Upper Eastern Branch Juuku Valley at 2060 to 2100 m asl in elevation. Three radiometric dates and preliminary archaeobotanical studies were conducted at three exposed profile cuts. The methods included here are: (1) pedestrian surveys; (2) use of digital maps (Google Earth, Encarta); (3) placing archaeological loci within known chronological time periods; (4) AMS dating of charcoal samples collected from profile deposits; and (5) preliminary identification of plant remains found from archaeobotanical samples. The results of our research represent the first step toward inventorying and interpreting archaeological data in the Juuku Valley derived from field studies.

This study aims to estimate the scientific productivity of collective subjects. The objective is to build a method for evaluating scientific productivity that allows calculating productivity, including for new collective subjects with a small citation network—the paper purposes the Time-Weighted PageRank method with citation intensity (TWPR-CI). The Citation Network Dataset (ver. 13) has been analyzed to verify the method. The dataset includes more than 5 million scientific publications and 48 million citations. There have been allocated four classes of collective subjects (more than 27,000 collective subjects in total). For each class, scientific productivity estimates from 2000 to 2021 were calculated using the PageRank, Time-Weighted PageRank, and TWPR-CI methods. It is shown that the advantage of the TWPR-CI method is the higher sensitivity of the scientific productivity estimates for new collective subjects on average during the first ten years of observation. At the same time, the assessment of scientific productivity for other collective subjects according to this method is stable. However, the small citation network of the new collective subjects does not allow an adequate assessment of scientific productivity during the first years of its operation. Therefore, the TWPR-CI method can be used to assess the scientific productivity of collective subjects, in particular the productivity of new ones.

An extended classification of active RC- and RLC- filters with Sallen-Key architectures, including those created in the last three years, is proposed. This makes it possible to formulate new design directions for an extended family of active RC- and RLC- Sallen-Key filters (PF, LPF, HPF, RF) for the tasks of high-speed and ultra-fast analog-to-digital signal conversion.

A new low-pass filter (LPF) circuit with independent adjustment of various, incl. digitally controlled, pole frequency resistors, pole quality factor and transmission coefficient. The proposed low-pass filter is based on the use of the properties of a multi-differential operational amplifier that performs the functions of a signal adder. The peculiarity of the filter is that it has three inputs, with respect to which different transmission coefficients are implemented, incl. inverting (-1) and non-inverting (+1). To check these properties of a low-pass filter in the Micro-Cap environment, computer simulation of a specific circuit was performed on a multi-differential operational amplifier AD 8130. Mathematical expressions are given for the main parameters of the proposed low-pass filter, which allow parametric synthesis of elements of a specific circuit under given restrictions on the used element base.

A new circuit of a low-pass filter (LPF) is considered, which is switched on at the input of analog-to-digital converters to limit the spectrum of input signals. The peculiarity of the proposed low-pass filter is the independent adjustment of the pole frequency, the quality factor of the pole and the transmission coefficient by different resistors. Computer simulation performed in the Micro-Cap environment confirms these properties of the LPF. The basic mathematical expressions are obtained, which make it possible to carry out the parametric synthesis of the LPF circuit. It is shown that the sensitivity of the LPF transmission coefficient to changes in the parameters of the frequency-setting elements of the circuit is close to zero and depends only on the ratio of the resistances of the two resistors in the feedback circuit.

The Simplified Spherical Harmonic (SPN) approximation was first introduced as a three-dimensional (3-D) extension of the plane-geometry Spherical Harmonic (PN) equations. A third order SPN (SP3) solver, recently implemented in the Nodal Expansion Method (NEM), has shown promising performance in the reactor core neutronics simulations. This work is focused on the development and implementation of the transport corrected interface and boundary conditions in NEM SP3 solver, following recent published work on the rigorous SPN theory for piecewise homogeneous regions. A streamlined procedure has been developed to generate the flux zero and second order/moment discontinuity factors (DFs) of the generalized equivalence theory to eliminate the error introduced by pin-wise homogenization. Moreover, several color set models with varying size and configuration are later explored for their capability of generating DFs that can produce results equivalent to that using the whole-core homogenization model for more practical implementations. The new developments are tested and demonstrated on the C5G7 benchmark. The results show that the transport corrected SP3 solver shows general improvements to power distribution prediction compared to the basic SP3 solver with no DFs or only zero order/moment DFs. The complete equivalent calculations using the DFs can almost reproduce transport solutions with high accuracy. The use of equivalent parameters from larger size color set models show better prediction in the whole-core calculations. By coupling different color set models DFs can offer the best accuracy at both eigenvalues and power distributions.

This study presents a pre-processing approach adopted for the radar reflectivity data assimilation and results of simulations with the Harmonie numerical weather prediction model. The method shows an improvement of precipitation prediction within the radar location area in both the rain rates and spatial pattern presentation. With the assimilation of radar data, the model simulates larger water content in the middle troposphere within the layer from 1 to 6 km, with major variations at 2.5–3 km; it also reproduces better the mesoscale belt and cell patterns of precipitation fields.

The article's purpose is a citation analysis of the impact of scientific publications by authors of different gender compositions. The PageRank method was chosen to calculate the citation impact of scientific publications, and the citation has also estimated the impact of scientific publications based on the number of citations. The normalized citation impact of scientific publications is calculated according to nine subsets of scientific publications that correspond to patterns of different gender compositions of authors. Also, these estimates were calculated for each country with which the authors of the publications are affiliated. The Citation database was chosen for the scientometric analysis Network Dataset ( ver . 13). The dataset includes more than 5 million scientific publications and 48 million citations. The main subject areas of scientific publications in this database are computer science, artificial intelligence, mathematics, engineering, etc. The results indicate that articles with a predominantly male composition are cited more than articles with a mixed or female composition of authors in this direction. Analysis of advantages in dynamics indicates that in the last decade for developed countries, there has been a decrease in the connection between the citation impact of scientific publications and the gender composition of their authors. However, the obtained results still confirm the presence of gender inequality in science, which may be related to socioeconomic and cultural characteristics, natural homophily, and other factors that contribute to the appearance of gender gaps. An essential consequence of overcoming these gaps, including in science, is ensuring the rights of people in all their diversity.

In this work, the possibility of fabrication magneto-optical ceramics by vacuum sintering of compacts prepared by electrophoretic deposition (EPD) from suspensions of (Ho0.95La0.05)2O3 (HoLa) nanopowders made by self-propagating high-temperature synthesis and (Y0.9La0.1)2O3 (YLa) nanopowders made by laser synthesis was systematically investigated. The processes of the formation of bulk one- and two-layer compacts by the EPD method from non-aqueous suspensions of nanopowders was studied. The use of acetylacetone and polyvinyl butyral (PVB) was shown to make it possible to obtain stable alcohol suspensions of the nanopowders characterized by high zeta potential values (+29…+80 mV) and to carry out a stable EPD process. One-layer compacts were made from the YLa and HoLa nanopowders with a density of 30–43%. It was found out that the introduction of PVB into the suspension leads to a decrease in the mass and thickness of the green bodies deposited, but does not significantly affect their density. A possibility to make two-layers (YLa/HoLa) compacts with a thickness of up to 2.6 mm and a density of up to 46% was demonstrated. Sintering such compacts in a vacuum at a temperature of 1750°C for 10 hours leads to the formation of ceramics with a homogeneous boundary between the YLa/HoLa layers and thickness of the interdiffused ions layer of about 30 μm.

Epidemics are the most common natural phenomena that have occurred throughout the entire history of human society. Depending on the type of disease and the development of the collective immunity that society had acquired by then, the consequences of epidemics were usually very severe. Precisely because of this, the aim of the paper is a scientific description of the way in which the prescribed preventive measures should be applied from the epidemiological, security, economic, legal and other aspects, so that the society, through the mechanisms of the state, can defend and rehabilitate the consequences of an epidemic of an infectious disease. Eliminating the epidemic's impacts is a very difficult issue. In particular, there is an infectious illness epidemic that is spreading uncontrolled throughout society on the one hand. In order to introduce a quarantine that restricts the epidemic's progress and, if the quarantine lasts long enough, to end the epidemic, contact between members of the social group must be broken. On the other side, the cessation of communication between members of a social group also signifies the cessation of all facets of life in that society, including economic ties, education, growth of culture, scientific research, etc.

The development of the automotive industry leads to the improvement of the designs of automatic transmissions and drives and to the development of methods for monitoring and diagnosing their condition. The trend of improving transmissions comes down mainly to the endless improvement of existing designs of CVTs and variators, which inevitably leads to the complication of designs and methods for their control and diagnostics.There is a need to create a fundamentally new simplified gearbox based on the scientific achievements of mechanics. However, the created structures remained inoperable due to the lack of theoretical justification.The adaptive gear variator developed by the author, which has CVT functions, is a mechanism with two degrees of freedom and with an additional constraint of a fundamentally new type, called a force - speed constraint. The force - speed constraint imposes a force restriction on the movement of links, while maintaining the number of degrees of freedom in the kinematics. Monitoring the state of the developed gearbox in the form of a non-switchable gear variator is greatly simplified, since the largest number of faults occur in the control system, and there is no control system in the gear variator. It seems possible to apply the digital twin method to diagnose the developed simplified CVT.The proposed article is devoted to a theoretical description of a fundamentally new adaptive gearbox, created on the basis of the latest achievements in mechanics, with the prospect of developing a simplified monitoring and diagnostic system for it

In a 24-week-long experiment, 31 rats were assigned to one of 3 groups: a Control group receiving standard chow and water, a Fructose group receiving standard chow and a 20% fructose solution, or an STZ+lipids group that received a fat-enriched diet following a single 25 mg/kg streptozotocin injection at the onset of the diet. Both groups experienced significantly increased caloric intake but did not gain weight above the Control group level. Adipocytes in subcutaneous and visceral adipose depots of both groups had smaller size compared to control and higher density in tissue. Respirometric analyses unveiled a substantial increase in mitochondrial respiration across all adipose tissue types in both dietary intervention groups, with greater changes observed in the Fructose group. Correlation analyses demonstrated that in both experimental groups high tissue respiration is associated with better biochemical profile and closer to control adipose tissue morphology. Increased tissue respiration in adipose depots could be an important mechanism of resilience to excessive caloric intake.

Positive invariant set is an important concept of dynamic systems. The purpose of this paper is to study the sufficient and necessary conditions that the set of ellipsoids and the Lorenz cone are positive invariant sets of discrete time systems. By means of nonlinear programming and induced norm, the problem of positive invariance is formulated as an optimization problem, and the equivalent dual form optimization is also presented using the dual optimization method. Our results provide more alternative methods for determining the positive invariance of quadratic form convex sets from the point of view of optimization and dual optimization. The effectiveness of this method is demonstrated by numerical examples.

A developing energy-saving approach of cold sintering in a pure aqueous medium was applied to the preparation of α-Al2O3 ceramics and performed on spark plasma sintering equipment. The initial γ-Al(OH)3 and γ-AlOOH powders and the cold-sintered ceramics were studied by X-ray diffraction analysis, infrared spectroscopy, thermal analysis, and scanning electron microscopy to reveal the chemical and structural transformations they experienced during the cold sintering. At 450°C and 70 MPa, initial γ-AlOOH transformed into a fragile α-Al2O3 material. Porous α-Al2O3 ceramics with about 60% porosity was obtained after cold sintering of γ-Al(OH)3 in the same conditions combined with subsequent annealing at 1250°C for 3 h. The role of water molecules in the studied processes was considered as the enhancement of structural mobility in the cold-sintered material due to its reversible hydroxylation similar to earlier investigated supercritical water action on the precursors during α-Al2O3 formation. Further improvement of the cold sintering setup and regimens would open prospects in α-Al2O3 ceramics manufacturing by an ecologically benign route.

Infectious diseases are a global health problem affecting billions of people. Developing rapid and sensitive diagnostic tools is key for successful patient management and curbing disease spread. Currently available diagnostics are very specific and sensitive but time-consuming and require expensive laboratory settings and well-trained personnel; thus, they are not available in resource-limited areas, for the purposes of large-scale screenings and in case of outbreaks and epidemics. Developing new, rapid, and affordable point-of-care diagnostic assays is urgently needed. This review focuses on CRISPR-based technologies and their perspectives to become platforms for point-of-care nucleic acid detection methods and as deployable diagnostic platforms that could help to identify and curb outbreaks and emerging epidemics. We describe the mechanisms and function of different classes and types of CRISPR-Cas systems, including pros and cons for developing molecular diagnostic tests and applications of each type to detect a wide range of infectious agents. Many Cas proteins (Cas9, Cas12, Cas13, Cas14) have been leveraged to create highly accurate and sensitive diagnostic tools combined with technologies of signal amplification and fluorescent, potentiometric, colorimetric, or lateral flow assay detection. In particular, the most advanced platforms -- SHERLOCK/v2, DETECTR, or CRISPR-Chip -- enable detection of attomolar amounts of pathogenic nucleic acids with specificity comparable to that of PCR but with minimal technical settings. Further developing CRISPR-based diagnostic tools promises to dramatically transform molecular diagnostics, making them easily affordable and accessible virtually anywhere in the world. The burden of socially significant diseases, frequent outbreaks, recent epidemics (MERS, SARS and the ongoing coronoviral nCov-2019 infection) urgently need the developing of express-diagnostic tools. Recently devised CRISPR-technologies represent the unprecedented opportunity to reshape epidemiological surveillance and molecular diagnostics.

This comparative study aims to investigate environmental awareness, knowledge, and safety among students in Montenegro and North Macedonia, considering the unique socio-cultural and environmental contexts of both countries. A mixed-methods approach involving surveys and interviews was employed to gather data from students in educational institutions across Montenegro and North Macedonia. The study assessed various factors, including students' awareness of environmental issues, their perceived level of knowledge, and their attitudes towards safety measures. A comprehensive series of 400 face-to-face interviews was carried out and these interviews encompassed 200 students from Montenegro and an equal number from North Macedonia, taking place at two esteemed academic institutions: The University of Montenegro in Podgorica and The University of St. Clement of Ohrid, Bitola, Republic of North Macedonia. Our hypothetical conceptual framework proposes that a combination of variables, including gender (H1), age (H2), year of study (H3), and rate of study (H4), significantly influences the attitudes of students from Montenegro and North Macedonia towards environmental awareness, safety, and knowledge. Research findings indicate significant variations in environmental awareness and knowledge perception among students in the two countries. While both Montenegro and North Macedonia face environmental challenges, differences in educational systems and socio-economic factors contribute to distinct attitudes and behaviors towards environmental issues and safety practices. This study sheds light on the importance of understanding regional differences in environmental awareness and knowledge perception among students. By identifying areas of strength and areas needing improvement, policymakers and educators can develop targeted interventions to enhance environmental education and foster a culture of sustainability in both Montenegro and North Macedonia.

The structural evolution and phase composition of multi-block thermoplastic polyurethanes, with different nature of the soft segments based on poly(butylene adipate) (PBA), were analyzed during in-situ thermal treatments. A combination of synchrotron small- and wide-angle X-ray scattering, differential scanning calorimetry, thermogravimetric analysis, and FTIR spectroscopy was used to determine the influence of macrodiol nature and crystallization conditions on the polymorphic behavior of PBA. Using a new synthesis scheme, a relatively high degree of crystallinity for urethane blocks was achieved, which depends on the diisocyanate type in the structure of the soft segment. The hard segment domains impose geometrical constraints on PBA, thereby altering its crystallization process compared to the neat oligomer. Thus, crystallization after annealing at a low temperature (80 °C) is fast, predominantly yielding a metastable β-phase. When heated to 180 °C, which is higher than the hard-segment melting temperature, a phase-separated structure is observed. Subsequent crystallization is slower, favoring the formation of the stable α-PBA modification. The phase separation can be observed even after the hard block melting. A notably slow crystallization from an isotropic melt was documented after the disruption of phase separation at 230 °C.

Characterized in biomedical terms, stretching exercises have been defined as movements applied by external and/or internal forces – to increase muscle and joint flexibility, decrease muscle stiffness, to elevate joint range of motion (ROM), to increase the length of the morpho-functional unit “muscle-tendon”, to improve joint, muscle and tendon movements, contraction and relaxa-tion. The present review examines and summarizes the initial and recent literature data related to the biomechanical, physiological and therapeutic effects of static stretching (SS) on flexibility and other physiological characteristics of the main structural and functional unit “joint-ligaments-tendon-muscle”. The healing and therapeutic effects of SS, soon combined with other rehabilitation techniques (massage, foam rolling – with and without vibrations; hot/cold therapy, etc.) are discussed in relationship to creation of individual (patient-specific) or group programs for treatment and prevention of joint injuries as well as for improving performance in sports. From a theoretical point of view, the role of SS as positively affecting the composition of the connective tissue matrix is pointed out: type I-III collagen synthesis, hyaluronic acid and glucosaminoglycans (GAGs) turnover – under influence of the transforming growth factor beta-1 (TGF-β-1). Different variables as collagen type, biochemistry, elongation and elasticity are used as molecular biomarkers. Recent studies evaluated that the static progressive stretching therapy could prevent/reduce the development of arthrogenic contractures, joint capsule fibrosis, muscle stiffness and need new clinical applications. Combined stretch techniques are proposed and ap-plied in medicine and sports, depending on their long- and short-term effects on variables such as ROM, EMG activity, muscle stiffness, etc. The results obtained are of theoretical and practical interest for development of new experimental, mathematical and computational models and creation of efficient therapeutic programs. The healing SS effects on the main structural and functional unit – “joint-ligament-tendon-muscle” need further investigations, which could clarify and evaluate benefits of SS in prophylaxis and treatment of joint injuries - in healthy and ill in-dividuals, in older adults, as compared to young, active and well-trained persons, as well as to professional athletes.

The deregulated markets have replaced the traditional way of trading electricity from the producers to the consumer, via government-owned organizations and regulated tariffs. Nowadays, electricity prices are determined by the offer-demand mechanism and consumers can negotiate tariffs with their supplier of choice. For classic wholesale suppliers, the tariffs are a result of the transactions performed on the wholesale market and the energy mix available in certain geographical regions. In parallel with becoming eligible and participating in retail electricity markets, the consumers use increasingly local generation sources based mostly on renewable energy technologies such as PV panels, and become prosumers. They want to be able to sell back to the market the generation surplus, in order to obtain the maximum benefits from their initial investment. Currently, several trading mechanisms for prosumers are available, ranging from the simplest, selling back the surplus to an aggregator at fixed tariffs, to more complex market schemes. This paper proposed a two-tier local market model for prosumers and consumers connected in microgrids, based on the blockchain technologies and other technologies and concepts such as remote sensing, smart grids, crowdsourcing and energy poverty.

The deregulated markets have replaced the traditional way of trading electricity from the producers to the consumer, via government-owned organizations and regulated tariffs. Nowadays, electricity prices are determined by the offer-demand mechanism and consumers can negotiate tariffs with their supplier of choice. For classic wholesale suppliers, the tariffs are a result of the transactions performed on the wholesale market and the energy mix available in certain geographical regions. In parallel with becoming eligible and participating in retail electricity markets, the consumers use increasingly local generation sources based mostly on renewable energy technologies such as PV panels, and become prosumers. They want to be able to sell back to the market the generation surplus, in order to obtain the maximum benefits from their initial investment. Currently, several trading mechanisms for prosumers are available, ranging from the simplest, selling back the surplus to an aggregator at fixed tariffs, to more complex market schemes. This paper proposed a two-tier local market model for prosumers and consumers connected in microgrids, based on the blockchain technologies and other technologies and concepts such as remote sensing, smart grids, crowdsourcing and energy poverty.

The paper proposes an innovative solution for managing and ensuring high energy efficiency of power supply systems at high non-linear loads. This is realized by maintaining optimal value of reliability indicators and high quality of power supply. The validation is carried out using analyzes and tests of quality of electromagnetic compatibility (EMC) for increased number of powered frequency converters. It has been proven that the effective use and reduction of energy consumption can be achieved thanks to the unique technological features of the employed electrical devices. This enables a normal operation of the system with decreased power and adequate control of energy processes. The problem of predicting power losses under changing conditions in a decentralized electrical network has been solved based on the theory of electromagnetic compatibility. The influence of the mains mode parameters and the indices of instantaneous distortion of current and voltage waveforms caused by the operation of converters on the resonance phenomena in power supply systems were investigated. Recommendations were developed for the selection of proper parameters of compensators for 6-10 kV and 0.4-0.66 kV circuits based on the analysis of the optimization problem when minimizing active power losses. Results of our findings may aid parties involved in designing and maintaining power networks in various applications, such as mines, etc.

Emerging of mass-spectroscopy with inductively-coupled plasma (ICP-MS) made possible to study the microelement composition of crude oil and its derivatives (with the limit of detection at the ppt level). We have studied the crude oil composition of some West Siberian and Tatarstan oilfields with the ICP-MS method to detect 50 rare, rare-earth, and other microelements. The elemental composition is reasonably comparable to their concentrations in ultrabasites whereas the contents of most of the elements are low to the limit. On the diagrams of rare-earth elements, one can see the prevalence of light lanthanides and positive europium anomaly. The study shows that crude oils have a specific microelement composition that stands out from other geological systems.

The gravel road pavement has a lower construction cost but poorer performance than the asphalt surface. It also emits dust and deforms under the impact of vehicle loads and ambient air factors. The resulting ripples and ruts are constantly deepening, increasing vehicle vibrations and fuel consumption, reducing safe driving speed and comfort. In this article, existing pavement quality evaluation indexes are analysed, and a methodology for their adaptation for roads with gravel pavement is proposed. This article reports the measured wave depth and length of the gravel pavement profile by the straightedge method of a 160 m long road section in three road exploitation stages. The measured pavement elevation was processed according to ISO 8608, and vehicle frequency response has been investigated using simulations in MATLAB/Simulink. The applied International Roughness Index (IRI) analysis showed that a speed of 30-45 km/h instead of 80 km/h provides the objective results of IRI calculation on the flexible pavement due to a decreasing velocity of vehicle's unsprung mass on a more deteriorated road pavement state. The influence of the corrugation phenomenon of gravel pavement has been explored, identifying specific driving safety and comfort cases. Finally, an increase in the Dynamic Load Coefficient (DLC) at a low speed of 30 km/h on the most deteriorated pavement and a high speed of 90 km/h on the middle-quality pavement demonstrates the demand for timely gravel pavement maintenance and the complicated prediction of a safe driving speed for drivers.

Background: Despite the fact that bone reconstructive surgeries are widely practiced worldwide, the search for an ideal bone replacement matetrial is still an open issue. We aimed to provide an overview of the current status of research and developments in this field with a focus on sapphire materials; Methods: A literature search and review was conducted using the PubMed, Scopus, and Embase databases. We searched for literature using the following keywords: bone implants; biocompatible materials; bone replacement material; sapphire implants; Results: Sapphire has a unique combination of mechanical, physical and chemical characteristics thanks to wich it has an excelent biocompatability and biointegrity.Unlike other materials it is incredibly strong and has a high endurance. The successful experience of using this material in medical instrument engineering, dentistry and cardiac surgery shows its benefits; Conclusions: We consider that sapphire is a perspective material for bone replacement implants and researchers should look in this direction.

We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

Grid refinement is used to save computing costs while preserving high precision of fluid simulation. In the Lattice Boltzmann Method, grid refinement often uses interpolated values. We found a method, where interpolation in space and time is not required. For this purpose, we used the moment matching condition and rescaling the non-equilibrium part of populations, and developed the recalibration procedure that allows to transfer information between different LBM stencils in the simulation domain. Then, we build non-uniform lattice which uses stencils with different shapes on the transition. The resulting procedure is verified on the 2D Poisselle flow and the advected vortex benchmark. In prospect, grids with adaptive geometry can be built with the use of the proposed method.

The interaction of human immunodeficiency virus with human cells is responsible for all stages of the viral life cycle, from the infection of CD4+ cells to reverse transcription, integration, and the assembly of new viral particles. To date, a large amount of OMICs data as well as information from functional genomics screenings regarding the HIV-1-host interaction has been accumulated in the literature and in public databases. We processed databases containing HIV-host interactions and found 2910 HIV-1-human protein-protein interactions, mostly related to viral group M subtype B, 137 interactions between human and HIV-1 coding and non-coding RNAs, essential for viral lifecycle and cell defense mechanisms, 232 transcriptomics, 27 proteomics, and 34 epigenomics HIV-related experiments. Numerous studies regarding network-based analysis of corresponding OMICs data have been published in recent years. We overview various types of molecular networks, which can be created using OMICs data, including HIV-human protein-protein interaction networks, co-expression networks, gene regulatory and signaling networks, and approaches for the analysis of their topology and dynamics. The network-based analysis can be used to determine the critical pathways and key proteins involved in the HIV life cycle, cellular and immune responses to infection, viral escape from host defense mechanisms, and mechanisms mediating different susceptibility of humans to infection. The proteins and pathways identified in these studies may represent a basis for developing new anti-HIV therapeutic strategies such as new small-molecule drugs preventing infection of CD4+ cells and viral replication, effective vaccines, "shock and kill" and "block and lock" approaches to cure latent infection.

This paper discusses approaches to the numerical integration of the coupled nonlinear Schrödinger equations system in case of few-mode wave propagation. The wave propagation assumes the propagation of up to nine modes of light in an optical fiber. In this case, the light propagation is described by the non-linear coupled Schrödinger equation system, where propagation of each mode is described by own Schrödinger equation with other modes interactions. In this case, the non-linear coupled Schrödinger equation system solving becomes increasingly complex, because each mode affects the propagation of other modes. The suggested solution is based on the direct numerical integration approach, which is based on a finite-difference integration scheme. The well-known explicit finite-difference integration scheme approach fails, due to the non-stability of the computing scheme. Due to this fact, the combined explicit/implicit finite-difference integration scheme, based on the implicit Crank–Nicolson finite-difference scheme, is used. It allows ensuring the stability of the computing scheme. Moreover, this approach allows separating the whole equation system on the independent equation system for each wave mode at each integration step. Additionally, the algorithm of numerical solution refining at each step and the integration method with automatic integration step selection are used. The suggested approach has performance gains (or resolutions) up to three or more orders of magnitude in comparison with the split-step Fourier method due to the fact that there is no need to produce direct and inverse Fourier transforms at each integration step. The main advantage of the proposed method is the ability to calculate the propagation of an arbitrary number of modes in the fiber.

Four-wire low voltage microgrids supply one-phase consumers with continuously changing electricity demand. For addressing climate change concerns, governments implemented incentive schemes for residential consumers, encouraging the installation of home PV panels for covering self-consumption needs. In the absence of sufficient storage capacities, the surplus is sold back by these entities, called prosumers, to the grid operator or in local markets, to other consumers. While these initiatives encourage the proliferation of green energy resources, and ample research is dedicated to local market designs for prosumer-consumer trading, the main concern of distribution network operators is the influence of power flows generated by prosumer surplus injection on the operating states of microgrids. The change in power flow amount and direction can greatly influence the economic and technical operating conditions of radial grids. This paper proposes a metaheuristic algorithm for prosumer surplus management that optimizes the power surplus injections using the automated control of three-phase inverters, with the aim of improving the active power losses and balancing the phase voltage profiles. A case study is performed on two real distribution networks with distinct layouts and load profiles and the algorithm shows its efficiency in both scenarios.

A growing number of households benefit from the government subsidies to install renewable generation facilities such as PV panels, used to gain independence from the grid and provide cheap energy. In the Romanian electricity market, these prosumers can sell their generation surplus only at regulated prices, back to the grid. A way to increase the number of prosumers is to allow them to make higher profit by selling this surplus back into the local network. This would also be an advantage for the consumers, who could pay less for electricity exempt from network tariffs and benefitting from lower prices resulting from the competition between prosumers. One way of enabling this type of trade is to use peer-to-peer contracts traded in local markets, run at microgrid (μG) level. This paper presents a new trading platform based on smart peer-to-peer (P2P) contracts for prosumers energy surplus trading in a real local microgrid. Several trading scenarios are proposed, which give the possibility to perform trading based on participants’ locations, instantaneous active power demand, maximum daily energy demand and the principle of first come first served implemented in an anonymous blockchain trading ledger. The developed scheme is tested on a low-voltage (LV) microgrid model to check its feasibility of deployment in a real network. A comparative analysis between the proposed scenarios, regarding traded quatities and financial benefits is performed.

Porous α-Al2O3 ceramics is a highly demanded material for multitude applications such as filters, substrates, biomedicine materials, etc. Despite the availability of the raw materials, a challenge of their technology is in a high energy budget caused by the sintering above 1500 °C. For a cold sintering processing (CSP) of ceramics, the lowering of α-Al2O3 sintering temperature is one of the most urgent challenges at the background of its rapid development. The current paper for the first time demonstrates the solution of the mentioned problem by the CSP of α-alumina ceramics in a presence of pure water as a transient liquid. The manufactured materials were examined by XRD analysis; the evolution of their microstructures during the CSP was revealed by SEM, and the porosity evaluated by the Archimedes method. The ceramics with an open porosity up to 36 % was produced at 380-450 °C, 220 MPa in 30 min. An increase in the pressure was found to impede α-Al2O3 formation from γ-AlOOH. The development of the microstructure was discussed within the frameworks of the dissolution-precipitation model and the homogenous nucleation. The results of the SEM study pointed to the coalescence of γ-AlOOH grains during the CSP.

The aim this text to present the confined covariant quark model (CCQM) and review its applications to the decays of B mesons. We do so in the context of existing experimental measurements and theoretical results of other authors, which we review also. The physics principles are in detail exposed for the CCQM, the other results (theoretical and experimental) are surveyed in an enumerative way with comments. We proceed by considering successively three categories of decay processes: leptonic, semileptonic and non-leptonic.

Bottlebrush (BB) elastomers with water-soluble side chains and tissue-mimetic mechanical properties are promising for biomedical applications like tissue implants and drug depots. This work investigates the microstructure and phase transitions of BB elastomers with crystallizable polyethylene oxide (PEO) side chains by real-time synchrotron X-ray scattering. In the melt, the elastomers exhibit the characteristic BB peak corresponding to the backbone-to-backbone correlation. Upon crystallization of the side chains, the intensity of the peak decays linearly with crystallinity, and eventually vanishes due to BB packing disordering within intercrystalline amorphous gaps. This behavior of the bottlebrush peak differs from an earlier study of BBs with poly(ε-caprolactone) side chains, explained by stronger backbone confinement in the case of PEO, a high-crystallinity polymer. Microstructural models based on 1D SAXS correlation function analysis suggest crystalline lamellae of PEO side chains separated by amorphous gaps of monolayer-like BB backbones.

We employ hierarchy of models (HoM) with 2, 3 and 4 parameters to reanalyze the nucleation kinetics in the electrodeposition as quantified by n(t) - “the number of nuclei vs. time” data obtained at different overvoltages from precise experiments on electrodeposition of Hg on two different types of Pt-cathodes by Ivan V. Markov and Evgenia Stoycheva [1]. The obtained two scales, nmax and , are used to rescale the original data mapping it on a master curve in coordinates . Our main result is obtained by studying further the dependence of these two scales on the overvoltage (analogue of supersaturation). Surprisingly, for one of the two cathode types - the “hemispherical single-crystal electrode” (as defined by the authors), there is discontinuity in the “ vs. overvoltage” dependence – an almost horizontal jump from 85 to 86 mV accompanied by a change in the slope of the dependence - it is ~ -1 and ~ -0.5 after. For the other cathode - “plane structureless platinum electrode”,  decreases smoothly. Combined, these two behaviors point at the so called “cusp catastrophe”. We compare our findings with published results on protein nucleation.

Papain-like protease PLpro, a domain within a large polyfunctional protein nsp3, plays key roles in the life cycle of SARS-CoV-2, being responsible for the first events of cleavage of a polyprotein into individual proteins (nsp1-4) as well as for the suppression of cellular immunity. Here, we developed a new genetically encoded fluorescent sensor, named PLpro-ERNuc, for detection of PLpro activity in living cells using translocation-based readout. The sensor was designed as follows. A fragment of nsp3 protein was used to direct the sensor on the cytoplasmic surface of endoplasmic reticulum (ER) membrane, thus closely mimicking the natural target of PLpro. The fluorescent part included two bright fluorescent proteins - red mScarlet I and green mNeonGreen, separated by a linker with the PLpro cleavage site. Nuclear localization signal (NLS) was attached to ensure accumulation of mNeonGreen into the nucleus upon cleavage. We tested PLpro-ERNuc in the model of recombinant PLpro expressed in HeLa cells. The sensor demonstrated expected cytoplasmic reticular network in the red and green channels in the absence of protease, and efficient translocation of the green signal into nuclei in the PLpro-expressing cells (14-fold increase of the nucleus/cytoplasm ratio). Then, we used PLpro-ERNuc in the model of Huh7.5 cells infected with SARS-CoV-2 virus, where it showed robust ER-to-nucleus translocation of the green signal in the infected cells 24 h post infection. We believe that PLpro-ERNuc represents a useful tool for screening PLpro inhibitors as well as for monitoring virus spread in a culture.

The main goal of this paper is to present results of preliminary archaeological research on the south side of Lake Issyk-Kul in Kyrgyzstan. We test the hypothesis that agropastoral land use changed over four millennia from the Bronze Age through the ethnographic Kirghiz period due to economic, socio-political, and religious changes in the prehistoric and historic societies of this region. Our research objectives are to: (1) describe and analyze survey results from Lower Kizil Suu Valley; (2) discuss the results of radiometric and archaeobotanical samples taken from three stratigraphic profiles from three settlements from the Juuku Valley, including these chronological periods: the Wusun period (200 to 400 CE), the Qarakhanid period (1100 to 1200 CE), and the ethnographic Kirghiz period (1700 to 1900 CE); and (3) conduct preliminary GIS spatial analyses on the Iron Age mortuary remains (Saka and Wusun period). This research emerges out of the first archaeological surveys conducted in 2019 - 2021 and includes the Lower Kizil Suu alluvial fan; it is an initial step toward developing a model for agropastoral land use for upland valleys of the Inner Tian Shan Mountains.

Early identification of viruses leads to more efficient disease management and control, and is extremely important. A possible new approach for creating virus sensors is the Electromagnetic echo effect (EMEE). An important feature is that the signal from EMEE is highly dependent on the state of the irradiated body. This makes it possible to control ongoing reactions, even if these reactions are invisible to the human eye or other equipment. This article shows the possibility of registering reaction occurring in the presence of an avian coronavirus causing infectious bronchitis, strain Massachusetts. The same methodology can be applied for other types of viruses as well.

Atmospheric correction is a necessary step in image processing data and spectra recorded by spaceborne sensors for pure cloudless atmosphere, primarily in the visible and near-IR spectral range. We have present a fast and sufficiently accurate method of atmospheric correction based on the proposed analytical solutions describing with high accuracy the spectrum of outgoing radiation at the top boundary of the cloudless atmosphere. This technique includes the model of the atmosphere and its optical parameters that are important in terms of radiation transfer. The solution of the inverse problem for finding unknown parameters of the model is carried out by the method of non-linear least squares (Levenberg-Marquardt algorithm) for an individual selected pixel of the image (its spectrum), taking into account the adjacency effects. Using the found parameters of the atmosphere and the average surface albedo, assuming homogeneity of the atmosphere within a certain area of the hyperspectral image (or the whole frame), the spectral albedo at the Earth's surface is calculated for all other pixels. It is essential that the procedure of the numerical simulation with non-linear least squares of the direct transfer problem is based on using analytical solutions, which provides a very short calculation time of the atmospheric parameters (seconds or less) and the ability to perform atmospheric correction "on-fly." Testing methods of atmospheric correction was performed using the synthetic outgoing radiation spectra at the top of the atmosphere (TOA), obtained by numerical simulation in the LibRadTran code, as well as spectra of real space images of the Hyperion hyperspectrometer. A comparison with the results of atmospheric correction in module FLAASH of ENVI package has been performed. Finally, to validate our data obtained by the SHARK method, a comparative analysis with ground-based measurements of Radiometric Calibration Network (RadCalNet) was carried out.

Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

The research considers creating a network of moss-based biotechnological purification filters in the Smart City concept. The extent of absorption of heavy metals and gases by Sphagnopsida moss under different conditions was investigated. The efficiency of air purification with biotechnological filters was also investigated using the example of the city of Almaty, Republic of Kazakhstan, where an excess of the permissible concentration of harmful substances in the air, according to the WHO air quality guidelines, is recorded throughout the year. Data on the level of pollution recorded by sensors located in the biggest Kazakhstani cities from 06/21/2020 to 06/04/2023 were selected as the basis for calculating the efficiency. In total, there are two hundred twenty sensors in 73 settlements of the Republic of Kazakhstan, with 80 such sensors located in the city of Almaty. Since creating a single biotechnological filter is expensive, the task was to calculate the air purification effect in the case of increasing the number of filters placed in polluted areas. As a result, it is shown that ten filters provide an air purification efficiency of 0.77%, 100 filters 5.72%, and 500 filters 23.11%. A biotechnological filter for air purification based on moss was designed at Astana IT University, considering the climatic features, distribution, and types of pollution in the Republic of Kazakhstan. The obtained results are essential for ensuring compliance with the ISO 37120:2018 standard for environmental comfort in the Republic of Kazakhstan. Additionally, the research findings and the experience of implementing a moss-based biotechnological filter can be applied to designing similar air purification systems in other cities. This is of great importance for the advancement of the field of urban science.

In this work, the use of graphite-like carbon nitride (g-C3N4) with improved texture characteristics for the synthesis of supported palladium catalysts of dehydrogenation of nitrogen-containing heterocycles was studied. This process is key to the creation of liquid organic carrier technology (LOHC) using N-heterocycles as reversibly hydrogenated/dehydrogenated substrates. For the preparation of g-C3N4-mca supports with advanced textural characteristics, well-established technology of the melamine cyanurate complex carbonization and standard techniques of adsorption precipitation together with wet impregnation were used for the synthesis of Pd-containing systems. The activity of the synthesized catalysts was studied in decahydroquinoline dehydrogenation. The high weight content of extractable hydrogen (7.2 wt %) and the high extraction rate, respectively, make it possible to consider these substances as the most promising N-heterocyclic compounds for this technology. It was shown that an increase in the specific surface area of g-C3N4 allows for achieving a slightly lower, but comparable fineness of palladium particles for the 1 wt% Pd/MCA-500 sample, compared to the standard 1 wt% Pd/C. In this case, the catalytic activity of 1 wt% Pd/MCA-500 in dehydrogenation of both substrates exceeded the analogous parameter for catalysts supported by nitrogen free supports. This regularity is presumably associated with the electron-donor effect of surface nitrogen, which favorably affects the dehydrogenation rate as well as the stability of catalytic systems.

Lead-based ternary chalcogenide thin films of the (PbTe)1-x(PbS)x system were obtained by plasma-enhanced chemical vapor deposition technique (PECVD) under conditions of a nonequilibrium low-temperature argon plasma of an RF discharge (40.68 MHz) at a reduced pressure (0.01 Torr). High-purity elements were directly used as starting materials – Pb, S and Te. Plasma-chemical synthesis was carried out on the surface of of c-sapphire and silicon substrate. The physicochemical properties of the films were studied by various analytical methods. The dependence of the Seebeck coefficient, resistivity, and power factor on the structural properties and composition has been studied. The thermoelectric characteristics were found to be dependent on the film composition. Upon the selection of optimal sulfur concentration one can increase the power factor as compared to single phase PbS ot PbTe films.

The global climate change mitigation efforts have increased the efforts of national government to incentivize local households in adopting individual renewable energy as a mean to help reduce the usage of electricity generated using fossil fuels and to gain independence from the grid. Since the majority of residential generation is made by PV panels that generate electricity at off-peak hours, the optimal management of such installations often considers local storage that can defer the use of locally generated electricity at later times. On the other hand, the presence of distributed generation can affect negatively the operating conditions of low-voltage distribution networks. The energy stored in batteries located in optimal places in the network can be used by the utility to improve the operation of the network. This paper proposes a metaheuristic approach based on a Genetic Algorithm that considers three different scenarios of using energy storage for reducing the losses in the network. Prosumer and network operator priorities can be considered in different scenarios inside the same algorithm, to provide a comparative study of different priorities in storage placement. A case study performed on a real distribution network provides insightful results.

Data can be illustrated in shapes, and the shapes could provide insight for data modeling and information extraction. Topological data analysis provides an alternative insight in biomedical data analysis and knowledge discovery with the algebra topology tools. In present work, we study the application of topological data analysis for personalized electrocardiographic signal classification toward arrhythmia analysis. Using phase space reconstruction technique, the signal samples are converted into point clouds for topological analysis facility. With topological techniques the persistence landscapes from the point clouds are extracted as features to perform the arrhythmia classification task. We find that the proposed method is robust to the training set size, with only a training set size of 20% percents, the normal heartbeat class are 100% recognized, ventricular beats for 97.13%, supra-ventricular beats for 94.27% and fusion beats for 94.27% within the corresponding experiments. The property of keeping high performance when using smaller training sample proves that the proposed method is especially applicable to personalized analysis. With the present study, we show that the topological data analysis technique could be a useful tool in biomedical signal analysis, and provide powerful ability in personalized analysis.

The paradigm of drug delivery via nano- and microcarriers is one of the leading ideas that enable overcoming the limitations of traditional chemotherapy. The trend toward more complex drug carriers capable of multifunctionality is observed in the literature. To date, prospects of stimuli-responsive systems to control the cargo release in the lesion nidus are widely accepted. Both endogenous and exogenous stimuli are employed for this purpose, however, endogenous pH is one of the most common triggers. Unfortunately, scientists face difficulties in the implementation of this idea since a range of biological barriers, drug bioavailability issues, and challenges in the synthesis of carriers with required properties have arisen. Here, we discuss fundamental strategies of pH-responsive drug delivery as well as limits in its application and reveal the main problems, weak sides, and reasons for poor clinical results. Also, we have made an attempt to formulate the profiles of "ideal" drug carrier in the frame of different strategies and considered recently published studies through the lens of these profiles. This approach enables the identification of current trends and promising vectors in the development of pH-responsive drug delivery systems, as well as challenges to be resolved in the next generation of carriers.

Innovative practices in irrigation systems can bring improvements in terms of economic efficiency and in the same time can reduce environmental impact. Investment in high tech technologies frequently involves additional costs, but an efficient water management can increase the lifetime of the equipment. The main objective of this article is to reduce the energy consumption by one thousand cubic meters pumped and automatically to increase the economic efficiency of the pumping groups. This paper develops a new operating algorithm that ensures the operation of the pumping group at safe operating intervals and in the same time identifies the equivalent pump operating points for the entire flow range and pumping height of the pumping group. This methodology is based on the principles of an Expert System to perform the optimization process of the energy consumption in pumping groups. The resulting methodology avoids the combinatorial explosion of the solutions to be analyzed and determines the point of maximum efficiency without violation of any of the system constraints under any operating condition. The proposed methodology is tested on an irrigation system that includes a pumping group with 5 pumps, showing its effectiveness in obtaining the optimal solution with a relatively low computational burden.

Objectives: Non-adhesive gel-like embolic materials (NAGLEMs) are becoming increasingly dominant in the endovascular treatment of hypervascularised formations in the head and neck due to a combination of their key properties. The main advantages include their lack of adhesion, effective distribution and penetration through pathological vessels, and crucially, their controlla-bility during the process. Our assigned duty was to scrutinise the literature and assess the efficacy and outcomes of administering NAGLEMs, in comparison to other embolizing substances (name-ly, coils, glue, and particles), among patients treated at our clinic. The procedures involved ana-lyzing the technical aspects, efficiency, and safety of endovascular therapy applied to two catego-ries of hypervascular pathological anomalies, surgically managed from 2015 to 2023. Arteriove-nous malformations (AVMs) located in the head, neck, and paragangliomas with jugular/carotid body localization are combined by intense shunting blood flow and shared requirements for em-bolizates used in endovascular treatment (such as penetration, distribution, delayed polymeriza-tion and controllability). An analysis of the literature was also conducted. Results showed 18 pa-tients diagnosed with neck paragangliomas of the carotid body and jugular type. Five patients with arteriovenous malformation (AVM) of the face and neck were included, consisting of 16 fe-males and 7 males with an average age of 55 ± 13 years. Endovascular procedures were conduct-ed using NAGLEMs (ONYX (Medtronic), SQUID (Balt), and PHIL (Microvention)) and dimethyl sulfoxide (DMSO)-compatible balloon catheters. All patients achieved complete or partial embo-lization of hypervascularized formations using one or more stages of endovascular treatment. Additionally, three AVMs of the face and two paragangliomas of the neck were surgically ex-cised following embolization. In other instances, formations were not deemed necessary to be re-moved. The patients' condition upon discharge was assessed by the modified Rankin Scale (mRs) and rated between 0 and 2. Conclusion: Currently, NAGLEMs are predominantly used to treat hypervascularized formations in the neck and head due to their fundamental properties. These properties include a lack of adhesion and a delay in predictable polymerization (after 30-40 minutes). NAGLEMs also exhibit excellent distribution and penetration throughout the vascular bed of the formation. Adequate controllability of the process is largely achieved through the pres-ence of embolism forms of different viscosity, as well as excellent X-ray visualization.

Three patients with severe life-threatening COVID-19 who failed to achieve substantial improvement on tocilizumab, received pulse therapy with corticosteroids (methylprednisolone, 1000 mg/day IV for three consecutive days) and intravenous immunoglobulin (20 g/day IV). This was associated with a prompt resolution of respiratory failure, elimination of cytokine release syndrome, and reversal of pulmonary CT changes. The treatment was generally safe and well tolerated. There was no evidence of protracted persistence of the virus in the patients who received pulse therapy. Randomized controlled trials are necessary to specify the efficacy and safety of high-dose methylprednisolone and intravenous immunoglobulin in the treatment of severe life-threatening COVID-19 separately or in combination.

Mining activities often generate important amounts of extractive waste, and as a consequence, environmental impacts that affects all factors to a greater or lesser extent. Depending on a variety of variables, the impact can be permanent or temporary, reversible or irreversible, negative or positive. This study conducted research on the status of closure and remediation processes of mining areas in Romania, specifically in the counties of Maramureș, Suceava, Harghita, Alba, Hunedoara, and Caraș-Severin. Furthermore, based on the type and level of pollution, the degree of application of remediation techniques for water and soil pollution in the investigated mining areas was studied. From the analysed information, it is evident that although the closure and remediation process started in Romania over 20 years ago, unfortunately, to this day, the technical projects, technical assistance, and execution of closure and remediation works have not yet completely solved the complex environmental issues in the mining sector. Most of the tailing ponds and waste piles of former mines continue to pose permanent specific risk to the environment and the population. This study concludes that the mining sector in Romania, although it has the necessary techniques and technologies for the ecological rehabilitation of degraded lands related to the Extractive Waste Facilities and the elimination of negative impacts on the environment and public health, has not yet been able to fully concretize its remediation efforts.

This paper uses preliminary studies of archaeological sites (burial mounds and settlements) from the Iron Age through Medieval periods (ca. 800 BCE to 1200 CE) in the Juuku Valley on the South side of Lake Issyk-Kul to model land-use across vertical mountain zones. To do so, we have established a radiometric chronology, conducted test excavations of an Iron Age settlement and a Turkic period burial, undertaken preliminary archaeobotanical research, and pedestrian surveys. Seed remains of wheat (Triticum aestivum), barley (Hordeum vulgare), broomcorn millet (Panicum milaceum) and foxtail millet (Setaria italica) and legumes were recovered in very small quantities from an Iron Age upland settlement at 2100 m asl and a Turkic period burial mound at 1934 m asl. These preliminary archaeobotanical results are compared to the Talgar Iron Age settlements on the north side of the Tian Shan Mountain range in Kazakhstan studied earlier by Robert Spengler. Small samples of faunal remains found at the Turkic period kurgan and from a profile at the upland Iron Age settlement indicate livestock herding of sheep/goats, cattle, and horses in Juuku Valley. The goal of this paper is to test the hypothesis that pastoral transhumance and agropastoralism were economic strategies used by ancient societies during the Iron Age through Medieval periods in mountain-river valley areas between 750 m to 2500 m asl. These economic strategies that combined the pasturing of sheep, goats, cattle and horses with the cultivation of cereals were adapted to the use of different vegetational zones along a vertical gradient. This paper based on preliminary research of upland sites of the Juuku Valley in Kyrgyzstan, initiates a long-term research study of four millennia of settlements that ranged from pastoral transhumance, pastoral nomadism, and combined mountain agriculture using survey data and test excavations.

The Malyy (Little) Murun massif of the Aldan Shield of the Siberian Craton has long been a kind of the geologists’ Siberian Mecca. It attracted thousands of geologists, prospectors and mineral collectors despite of its remote location. It is famous for a dozen of new and rare minerals, including gemstones charoite and dianite (the latter is the market name for strontian potassicrichrerite), as well as for specific alkaline igneous rocks. Despite of this, the age of the Malyy Murun igneous complex and associated metasomatic and hydrothermal mineral associations remained poorly constrained. In this paper, we provide extensive 40Ar/39Ar geochronological data to reveal its age and temporal history. It appeared that being unique in terms of rocks and constituent minerals, the Malyy Murun is one of multiple alkaline massifs and lavas emplaced in Early Cretaceous (~137-128 Ma) within a framework of extensional setting of the Aldan Shield and nearby Transbaikalian region. The extension has occurred 40-60 million years after the supposed closure of the Mongolia-Okhotsk Ocean and peak of orogeny in Early-Middle Jurassic.

The influence of neutrosophy in the previous period is constantly growing in many areas of science and technology. Moreover, various applications of the neutrosophic approach have become more common in recent years. Our goal in this research is to utilize the neutrosophy to improve the performance of the Dai-Liao conjugate gradient (CG) method. Specifically, in this research, we propose and investigate a new neutrosophic logic system to calculate the key parameter t involved in the Dai–Liao CG iterations. Theoretical analysis and numerical experience indicate that the efficiency and robustness of the new rule for determining t. Combining the neutrosophy and the Dai-Liao conjugate gradient method, we propose and explore a new Dai-Liao CG iterations for solving large-scale unconstrained optimization models. The global convergence is established under common assumptions and the backtracking line search. Finally, by conducting numerical experiments, computational evidence demonstrates that the new fuzzy neutrosophic Dai-Liao conjugate gradient method is computationally effective and robust.

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

The work presents an approach to instrument the load sensing bearings for automotive applications for estimation of the loads acting on the wheels. The system comprises fiber-optic sensors based on addressed fiber Bragg structures (AFBS) with two symmetrical phase shifts. A mathematical model for load-deformation relation is presented, and the AFBS interrogation principle is described. The simulation includes (i) modeling of vehicle dynamics in a split-mu braking test, during which the longitudinal wheel loads are obtained, (ii) the subsequent estimation of bearing outer ring deformation using a beam model with simply supported boundary conditions, (iii) the conversion of strain into central wavelength shift of AFBS, and (iv) modeling of the beating signal at the photodetector. The simulation results show that the estimation error of the longitudinal wheel force from the strain data acquired from a single measurement point was 5.44% with root-mean-square error of 113.64 N. A prototype load sensing bearing was instrumented with a single AFBS sensor and mounted in a front right wheel hub of an experimental vehicle. The experimental setup demonstrated comparable results with the simulation during the braking test. The proposed system with load-sensing bearings is aimed at estimation of the loads acting on the wheels, which serve as input parameters for active safety systems, such as automatic braking, adaptive cruise control, or fully automated driving, in order to enhance their effectiveness and safety of the vehicle.

Authorities and governmental bodies strongly emphasize the importance of residents preparing for natural disasters, particularly underscoring the significance of readiness for geophysical hazards like earthquakes. In this study, which represents comparative quantitative research, the levels and predictors of the impact on preparedness for earthquake-induced disasters in South-Eastern Europe countries such as Montenegro, North Macedonia, and Serbia are examined. Using the snowball sampling technique (online questionnaire), a survey of 1245 respondents (Montenegro (n = 400), North Macedonia (n = 345), and Serbia (n = 500) was conducted from February 2023 to February 2024. The paper is based on the central hypothesis that the most significant predictor of earthquake preparedness in Montenegro, North Macedonia, and Serbia is age, followed by gender and education. Multivariate regression analysis was used to determine the extent to which five scores of the subscales (household preparedness, community preparedness, disaster preparation, earthquake risk awareness, reinforced house) were associated with seventh demographic and socio-economic variables. In addition to the mentioned analysis, other statistical analyses such as T-test, one-way ANOVA analysis, and Pearson correlation were also utilized. The results indicate that age emerges as a predictor in various aspects of earthquake-induced disaster preparedness and awareness in most models, followed by education. These findings confirm the significance of respondents' age in determining levels of preparedness and earthquake awareness. Overall, in North Macedonia, respondents recorded the highest ratings (M = 3.52) for household preparedness for earthquakes, compared to Montenegro (M = 2.98) and Serbia (M = 3.26), where the lowest ratings were recorded. Research findings, taking into account cultural characteristics, can serve as a basis for the development of targeted interventions, strategies, policies, and programs aimed at improving the level of societal preparedness for earthquake-induced disasters.

Glycerol represents a useful functional component of heat-transfer fluids. Glycerol is known to be triboelectrically active. We report how the flow of glycerol, stopped in a cylindrical coiled pipe, influences horseradish peroxidase (HRP) enzyme. Namely, glycerol flow was pumped through the coil and then stopped. After that, we incubated the 0.1 µM solution of HRP near the side of the coil, and then adsorbed HRP onto mica. This operation markedly increased the HRP aggregation on mica in comparison with the control sample. We explain this phenomenon by the influence of triboelectrically induced electromagnetic fields. Our results can be useful in the development of flow-based systems for biosensors and bioreactors.

A facile and environmentally benign method for a single-phase barium titanate synthesis in water vapor medium was studied to reveal the mechanism of phase transformation of the initial simple oxides mixture and estimate the capability of the product to be used as a raw material for low-frequency dielectric ceramics. The composition and structure of the reaction mixture treated in vapor at 130…150 °C as well as 230 °C for various time were investigated by means of XRD, SEM, HRTEM, EDX, and FTIR methods. The kinetics of the occurring phase transformation was described by Johnson-Mehl-Avrami-Erofeev equation. The reaction between the initial oxides was considered as a topochemical process with an apparent activation energy of 74…80 kJ mol^-1. A crucial role in this process belonged to the water vapor medium, which facilitated the generation of the reaction zone and its spreading inward the solid particles. The synthesized tetragonal barium titanate powder (mean particle size of 135 ± 24 nm) was sintered by a conventional technique at 1250 °C to obtain ceramics with grains of about 2 μm. Capacitance measurements performed a dielectric constant and loss tangent of ceramics, which reached 3879 and 6.7 10^-3, respectively, at 1 kHz and room temperature.

Objective: The purpose of this study was to evaluate the surface texture and biofilm adhesion of veneered or CAD/CAM milled zirconia (partially stabilized with yttrium) after professional oral hygiene procedures. Samples (4x4 mm, thickness 2 mm; n = 72) were separated from zirconia blanks (3Y-TZP-LA). One group was veenired with ceramics and the other group of samples was CAD/CAM milled. Each group had 2 subgroups: polished and glazed. The samples were subjected to simulated strokes of professional brushing using abrasive paste and ultrasonic scaling. Parameters of surface micromorphology and receptivity to biofilm were calculated before and after simulating the given methods of professional maintenance of oral hygiene. The characteristics of zirconia surface were evaluated by scanning electron microscopy (SEM). Microbial bacterial/fungal species (Staphylococcus aureus, Streptococcus sanguinis and Candida albicans) were used and cultured on the respective sterilized zirconia surfaces. The amount of biofilm formation on zirconia surface was quantified by colony forming unit (CFU) counts. Results: SEM analysis showed the greatest change in surface microtopography after the use of ultrasonic scaling, in glazed zirconia samples. Less formation of colonies on the surface CAD/CAM milled zirconia restorations was observed. Conclusion: Routine methods of professional maintenance of oral hygiene can damage the surface of glazed zirconia restorations.

Novel tetragonal matrix Ba0.5Gd0.5-xNaxF2.5-x, where x = 0.05, doped by Yb3+, Ho3+, Er3+, was synthesized by molten salt synthesis (MSS) from nitrate flux. XRD data show that tetragonal phase with a = 4.122(1) Å, c = 17.672(1) Å is stable in argon atmosphere up to 960 °C. Luminescence spectra recorded in 500-900 nm and 1050-1700 nm upon 974 nm pumping demonstrated the characteristic luminescence at 1550 nm (4I13/2 → 4I15/2) for Er3+ and 1150 nm (5I6 → 5I8) for Ho3+. The relative thermal sensitivity (Sr) at 296-316 K were 0.3 %*K-1 and 5.5%*К-1 in shortwave infrared (SWIR) and visible range, respectively. Synthesized luminophores can be used as dual-range optical temperature sensors, which simultaneously operating in visible and SWIR ranges.

We present the case of a 35-year-old patient without pathological history who developed hemopneumothorax due to altitude barotrauma during a commercial airline flight. The computed tomography of the chest identified the presence of emphysema "blebs" and bubbles, and the histopathological examination of the lung fragment obtained during the diagnostic and therapeutic thoracoscopy identified elements suggestive for the diagnosis of respiratory bronchiolitis associated with desquamative interstitial pneumonia (DIP).

Estrogens play a protective role during early life stages. However, endogenous 17β-estradiol (E2) can accelerate atherosclerosis progression in low-grade inflammatory conditions like established atherosclerosis. Our single-center cohort study assessed sex-specific associations of gonadal hormones with oxidative stress, inflammation, and myocardial injury markers in 111 patients (37% women) diagnosed with acute myocardial infarction (MI) between July 2011 and December 2013. Blood samples were collected within 48 hours of symptom onset, and we measured sex steroids (E2, total testosterone [T]), oxidized low-density lipoproteins, high-sensitive C-reactive protein (CRP), white blood cell counts (WBC), and cardiac enzymes (creatine kinase [CK], the CK Muscle-Brain fraction [CK-MB], and high-sensitive troponin T [hsTnT]). The SYNTAX score gauged coronary disease severity from coronary angiography results. In men with acute MI, peak cardiac enzyme levels were predicted by post-percutaneous coronary intervention (PCI) E2 plasma levels (OR 1.011, p=0.047 - CK; OR 1.018, p=0.013 - CK- MB; OR 1.019, p=0.005 - TnT), peak WBC count (OR 1.487, p=0.015 - CK ; OR 1,709, p=0,005 - CK- MB; OR 1.391, p=0.012 - TnT), and peak CRP plasma levels (OR 1.040, p=0.033 - CK; OR 1.024, p=0.029 - CK-MB; OR 1.063, p=0.006 - TnT). T levels and E2/T ratio were associated with post-PCI CRP in these men (OR 0.980, p = 0.024 - T, OR 1.010, p = 0.076 - CRP). For women, peak WBC was a marker of highest testosterone (OR 1.348, p = 0.062), and only WBC was a significant indicator of myocardial injury extent (OR 1.426, p=0.039 - CK; OR 1.384, p=0.036 - CK-MB; OR 1.299, p=0.048 - TnT). During acute MI, elevated endogenous estradiol levels correlate with myocardial necrosis severity in men, while in women, increased leukocyte levels indicate acute myocardial damage. Elevated plasma T is associated with increased WBC in women. In men, post-PCI plasma CRP specifically indicates endogenous T levels and E2/T ratio during the acute phase.

Multidrug-resistant (MDR) Pseudomonas aeruginosa infections represent major a public health concern and require comprehensive understanding of their genetic make-up. This study investigated the first occurrence of IMP-carrying MDR P. aeruginosa strains from Bulgaria. Whole genome sequencing identified a novel plasmid-mediated blaIMP-100 allele located in a In1300-like integron embedded in a novel putative transposon. Two other closely related chromosomal blaIMP variants IMP-13 and IMP-84 were also detected. The IMP-producers were resistant to last-line drugs including cefiderocol (CFDC) (2 out of 3) and susceptible to colistin. The blaIMP-13/84 cassettes were situated in a In320 integron inserted in a Tn5051-like transposon as previously reported. Lastly, the p47825-IMP plasmid rendered PAO1 transformant resistant to CFDC, suggesting a transferable CFDC resistance. A variety of virulence factors associated with adhesion, antiphagocytosis, iron uptake, quorum-sensing, as well as secretion systems, toxins, and proteases were confirmed, suggesting significant pathogenic potential consistent with the observed strong biofilm formation. Emergence of IMP-producing MDR P. aeruginosa is alarming as they remain unsusceptible even to last geneneration drugs like CFDC. Newly detected IMP-100 was even located in an CFDC-resistant XDR strain.

Micro- and nanoflowers are a class of materials composed of particles with high surface-to-volume ratio. They are being extensively studied in the last decade due to simple preparation protocols and promising applications in biosensing, as drug delivery agents, for water purification and so on. Flowerlike objects, due to their highly irregular surface, may act also as plasmonic materials, providing resonant coupling between optical waves and surface plasmon excitations. This fact infers for the possibility to use micro- and nanoflowers as effective surface-enhanced Raman scattering (SERS) substrate materials. Here, we report on the design and Raman enhancement properties of silver flowerlike structures, deposited on aluminum surface. A simple and cost-effective fabrication method is described, which leads to SERS substrates of high developed surface area. The morphology of the silver flowers on a nanoscale is characterized by self-organized quasiperiodic stacks of nanosheets, which act as plasmonic cavity-resonators. The substrates were tested against rhodamine-6G (R6G) water solutions of concentration varying between 10^–3 M and 10^–7 M. Optimal SERS enhancement factors of up to 10⁵ were established at R6G concentrations in the range 10^–6 – 10^–7 M.

In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

With the automotive industry moving towards automated driving, sensing is increasingly important in enabling technology. The virtual sensors allow data fusion from various vehicle sensors and provide a prediction for measurement that is hard or too expensive to measure in another way or in the case of demand on continuous detection. In this paper, virtual sensing is discussed for the case of vehicle suspension control, where information about the relative velocity of the unsprung mass for each vehicle corner is required. The corresponding goal can be identified as a regression task with multi-input sequence input. The hypothesis is that the state-of-art method of Bidirectional Long-Short Term Memory (BiLSMT) can solve it. In this paper, a virtual sensor has been proposed and developed by training a neural network model. The simulations have been performed using an experimentally validated full vehicle model in IPG Carmaker. Simulations provided the reference data which was used for Neural Network (NN) training. The extensive dataset covering 26 scenarios has been used to obtain training, validation and testing data. The Bayesian Search was used to select the best neural network structure using root mean square error as a metric. The best network is made of 167 BiLSTM, 256 fully connected hidden units and 4 output units. Error histograms and spectral analysis of the predicted signal compared to the reference signal are presented. The results demonstrate the good applicability of neural network-based virtual sensors to estimate vehicle unsprung mass relative velocity.

HIV-1 Tat protein interacts with TAR RNA and recruits CDK9/cyclin T1 and other host factors to induce HIV-1 transcription. Thus Tat-TAR RNA interaction, which is unique for HIV-1, represents an attractive target for anti-HIV-1 therapeutics. To target Tat-TAR RNA interaction, we used a crystal structure of TAR RNA with acetylpromazine bound to the bulge of TAR RNA, to dock compounds from Enamine database containing 1.6 million individual compounds. Docking identified 173 compounds that were analyzed for the inhibition of HIV-1 infection. Top ten inhibitory compounds with IC50 ≤ 6 µM were selected and the three least toxic compounds, T6780107 (IC50=2.97 μM), T0516-4834 (IC50=0.2 μM) and T5628834 (IC50=3.46 μM), were further tested for HIV-1 transcription inhibition. Only T0516-4834 compound showed selective inhibition of Tat-induced HIV-1 transcription, whereas T6780107 compound inhibited equally basal and Tat-induced transcription and T5628834 compound only inhibited basal HIV-1 transcription. The T0516-4834 compound also showed strongest inhibition of HIV-1 gag RNA expression and p24 production in CEM T cells infected with HIV-1 IIIB. Of the three compounds, only the T0516-4834 compound disrupted Tat-TAR RNA interaction indicating that it might target TAR RNA. Also, of the three tested compounds, T5628834 but not T6780107 or T0516-4834 disrupted Tat-CDK9/cyclin T1 interaction. Taken together, our study identified novel compound T0516-4834 that disrupted Tat-TAR RNA interaction and inhibited Tat-induced transcription and HIV-1 infection suggesting that this compound might serve as a new lead for anti-HIV-1 therapeutics.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

Carbapenemase-producing Enterobacter spp. Serratia marcescens, Citrobacter freundii, Providencia spp. and Morganella morganii (CP-ESCPM) are increasingly identified as causative agents of nosocomial infections but are still not under systematic genomic surveillance. In this study, using a combination of whole genome sequencing and conjugation experiments, we sought to elucidate the genomic characteristics and transferability of resistance genes in clinical CP-ESCPM isolates from Bulgaria. Among the 36 sequenced isolates, NDM-1 (12/36), VIM-4 (11/36), VIM-86 (8/36) and OXA-48 (7/36) carbapenemases were identified; two isolates carried both NDM-1 and VIM-86. The majority of carbapenemase genes were found on self-conjugative plasmids. IncL plasmids were responsible for the spread of OXA-48 among E. hormaechei, C. freundii and S. marcescens. IncM2 plasmids were generally associated with the spread of NDM-1 in C. freundii and S. marcescens, and also of VIM-4 in C. freundii. IncC plasmids were involved in the spread of the recently described VIM-86 in P. stuartii isolates. IncC plasmids carrying blaNDM-1 and blaVIM-86 have been observed too. blaNDM-1 was also detected on IncX3 in S. marcescens and on IncT plasmid in M. morganii. The significant resistance transfer rates highlight the role of the ESCPM group as a reservoir of resistance determinants and stress the need for strengthening the infection control measures.

This work presents the synthesis and self-organization of the calamitic fluorinated mesogen, 1,1,2,2-tetrafluoro-2-(1,1,2,2-tetrafluoro-4-iodobutoxy)ethanesulfonic acid, a potential model for perfluorosulfonic acid membranes (PFSA). The compound is derived in three steps from 1,1,2,2-tetrafluoro-2-(1,1,2,2-tetrafluoro-2-iodoethoxy)ethanesulfonyl fluoride, achieving an 78% overall yield. The resulting compound exhibits intricate thermal behavior. At 150 °C, a crystal-to-crystal transition is observed due to the partial disordering of calamitic molecules, which is followed by isotropization at 218 °C. Upon cooling, sample ordering occurs through the formation of large smectic liquid crystalline phase domains. This thermotropic state transforms into a layered crystal phase at lower temperatures, characterized by alternating hydrophilic and hydrophobic layers. Using X-ray diffraction, crystalline unit cell models at both room temperature and 170 °C were proposed. Computer simulations of the molecule across varying temperatures support the idea that thermal transitions correlate with a loss of molecular orientation. Importantly, the study underscores the pivotal role of precursor self-organization in aligning channels during membrane fabrication, ensuring controlled and oriented positioning.

A hydrothermal technique with microwave heating (200 °C, 2 hours, 2 magnetrons, 2.45 GHz) was modified to obtain UV-C luminescent LaPO4: Pr3+ colloidal nanorods for the potential use in X-ray cancer theranostics. For further possible biofunctionalization, a compound of tartaric acid formed under basic conditions was used as a coating and stabilizing agent to provide colloidal properties to the surface of nanoparticles in basic to neutral aqueous media, which was confirmed by zeta potential measurements. In addition, the colloidal properties and clustering processes of synthesized LaPO4:Pr3+ nanorods in aqueous solutions with different pH values were studied in real time using a highly sensitive laser ultramicroscope operating according to the “light-sheet” scheme. A comparative analysis of the transmission electron microscopy, X-ray powder diffraction and high-energy spectroscopy showed the different effects of synthesis parameters on the morphological, crystalline and luminescent properties of the obtained nanorods. Through optimization of the synthesis parameters, stable aqueous solutions of m-LaPO4:Pr3+ nanorods with sizes less than 30 nm and an intensity of UV-C luminescence equal to 5-10% of the unmodified nanofibers were obtained.

Porcine circovirus type 2 (PCV2) is responsible for a number of porcine circovirus associated diseases (PCAD) that can severely impact domestic pig herds. For a non-enveloped virus with a small genome (1.7 kb ssDNA), PCV2 is remarkably diverse, with 8 subtypes (a-h). New subtypes of PCV2 can spread through migration of wild boars, which are thought to infect domestic pigs and spread further through the domestic pig trade. Despite a large swine population, the diversity of PCV2 subtypes in Ukraine has been undersampled, with few PCV2 genome sequences reported in the past decade. To gain a deeper understanding of PCV2 subtype diversity in Ukraine, samples of blood serum were collected from wild boars (n = 107) that were hunted in Ukraine during the November-December 2012 hunting season. We found 34/107 (31.8%) prevalence of PCV2 by diagnostic PCR. For domestic pigs, liver samples (n = 16) were collected from a commercial market near Kharkiv in 2019, of which 6/16 (37%) were positive for PCV2. We sequenced the genotyping locus ORF2, a gene encoding the PCV2 viral capsid (Cp), for 11 wild boar and 6 domestic pig samples in Ukraine using an Oxford Nanopore MinION device. Of 17 samples with resolved subtypes, PCV2 subtype b was most common in wild boar (10/11, 91%), while domestic pigs were infected with subtypes b and d. We also detected subtype b/d and b/a co-infections in wild boar and domestic pigs, respectively, and subtype f in a wild boar from Poltava for the first time in Ukraine. Building a maximum likelihood phylogeny, we identified a sublineage of PCV2 subtype b infections in both wild and domestic swine, suggesting a possible epizootic cluster and ecological interaction in northeastern Ukraine.

The spatial and temporal variability in dietary preferences of juvenile three-spined stickleback Gasterosteus aculeatus, was studied across typical coastal habitats of Keret Archipelago, Kandalaksha Bay, the White Sea. Sampling of fish using beach seine was implemented in late July-early August and in late August, and zooplankton samples were collected to make a quantitative evaluation of abundance of potential prey items. Similarity Percentage (SIMPER) analysis implemented over the data obtained from stomach content analysis revealed five planktonic taxa mostly contributing to the diet of juvenile sticklebacks, of which copepod Temora longicornis was the most important prey item at marine sites, while Acartia longiremis prevailed in diet of fishes in marine lagoon. Calculation of selectivity index demonstrated that some taxa (e.g., A. longiremis) were always avoided by juvenile fishes, others (e.g. Microsetella norvegica) were firstly avoided and then selected in late August. Calculation of selectivity index was implemented per sample and per individual fish indicated that taxa like T. longicornis and were selected during the whole period of study, fishes demonstrated pronounced individual variation in prey selectivity. In general, data on selectivity indicated that despite juvenile sticklebacks feed on mostly available prey items, they can demonstrate taxonomic and size-specific prey selectivity.

To develop a modern plague vaccine, we used hypo-endotoxic Yersinia pestis bacterial ghosts (BGs) with combinations of genes encoding the bacteriophage ɸX174 lysis-mediating protein E and/or holin-endolysin systems from λ or L-413C phages. Expression of the protein E gene resulted in the BGs that retained the shape of the original bacterium. Co-expression of this gene with genes coding for holin-endolysin system of the phage L-413C caused formation of structures resembling collapsed sacs. Such structures, which have lost their rigidity, were also formed as a result of the expression of only the L-413C holin-endolysin genes. Similar holin-endolysin system from phage λ containing mutated holin gene S and intact genes R-Rz coding for the endolysins caused generation of mixtures of BGs that had (i) practically preserved and (ii) completely lost their original rigidity. The addition of protein E to the work of this system shifted the equilibrium in the mixture towards the collapsed sacs. The collapse of the structure of BGs can be explained by endolysis of peptidoglycan sacculi. Immunizations of laboratory animals with the variants of BGs followed by infection with a wild-type Y. pestis strain showed that bacterial envelopes protected only cavies. BGs with peptidoglycan maximally hydrolyzed had a greater protectivity compared to BGs with preserved peptidoglycan skeleton.

Studies of dietary preferences of migratory species are of great importance as these species connect food webs of habitats across the migration route and thus represent trophic relationships between the spatially disjointed communities. Here we describe dietary preferences of threespine stickleback G. aculeatus in the White Sea during the spawning season using stable isotope and stomach content analyses. Both analyses indicated that during the spawning season, when sticklebacks spend most of the time in the inshore, their diet significantly consist of benthic species in contrast to the start of the spawning season when fishes migrating from the offshore are feeding on zooplankton. Also, we show that stickleback eggs contribute greatly to the diet of both male and female fishes. Using Bayesian mixing modelling we show that dietary preferences in females were broader than in males, and more variable during the spawning season. Males fed on eggs almost while guarding their nests. Both stomach contents and isotope signatures demonstrate that by the end of the spawning season sticklebacks again increase consumption of plankton, and isotope analysis proved to be more reliable tool to trace this change than stomach content analysis. Our results show that stable isotope and stomach content analyses well supplement each other in understanding of seasonal changes in dietary composition of stickleback.

In these last years, self-healing polymers have emerged as a topic of considerable interest owing to their capability to partially restore material properties and thereby extend the product's lifespan. The main purpose of this study is to investigate the nano-indentation response in terms of hardness, reduced modulus, contact depth and coefficient of friction of a self-healing resin developed for use in aeronautical and aerospace contexts. To achieve this, the bifunctional epoxy precursor underwent tailored functionalization to improve its toughness, facilitating effective compatibilization with a rubber phase dispersed within the host epoxy resin. This approach aimed to highlight the significant impact of the quantity and distribution of rubber domains within the resin on enhancing its mechanical properties. The main results are that pure resin exhibits a higher hardness (about 36.7% more) and reduced modulus (about 7% more), consequently leading to a lower contact depth and coefficient of friction (11.4% less) compared to other formulations that, conversely, are well-suited for preserving damage from mechanical stresses due to their capabilities in absorbing mechanical energy. Furthermore, finite element method (FEM) simulations of the nanoindentation process were conducted. The numerical results were meticulously compared with experimental data, demonstrating a good agreement. This validation of the FEM model underscores its efficacy in predicting the mechanical behavior of nanocomposite materials under nanoindentation. The proposed investigation aims to contribute knowledge and optimization tips about self-healing resins.

Host ribosome-associated scaffold protein Receptor for Activated C Kinase 1 (RACK1) is utilized by a diverse group of human viruses for Internal Ribosomal Entry Sites (IRES) – mediated translation of viral mRNAs. We recently reported inhibition of herpes virus by small molecules targeting the RACK1 functional site. Here, we tested these molecules against HIV-1 and HCV, as HIV-1 contains two potential IRES sites and HCV translation occurs exclusively through IRES. Compounds significantly downregulated activities of HIV-1- and HCV-related dicistronic reporter constructs in transfected HEK293T cells. The compounds also strongly downregulated production of the HIV-1 capsid protein p24 in HIV-infected cells, as well as production of HIV-1 Gag precursor p55 and p55-derived proteins p24 and p17 in cells infected with the HIV-1 virus. Hepatitis C virus (HCV) IRES activities were also significantly inhibited by RACK1 inhibitor compounds. Since a number of human and plant pathogenic viruses are reported to use IRES, the RACK1 compounds can be established as broad host-targeted antivirals.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Plasmonic sensors have great potential for widespread usage, but the prohibitive cost of noble metals restrains the wider adoption of this technology. The aim of our study is to develop a cost-effective Al-based alternative to plasmonic detectors commonly based on noble metals. We considered a structure that consists of a Si p-n junction with an overlying grating-relief aluminum layer. The investigation of the infrared plasmonic resonance dependency on the structure geometric parameters and optimization of the fabrication process allowed us to determine optimal parameters for photodetection enhancement. The resonance photoresponse of optimized aluminum-based plasmon-polariton photodetector was significantly improved and became comparable to noble metal-based analogs. Our results can be used for the creation of cost-effective high-sensitivity plasmonic sensors.