High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

In the pursuit of China’s dual carbon goals, identifying spatio-temporal changes in industrial carbon emission efficiency and their influencing factors in cities at different stages of development is the key to effective formulation of countermeasures to promote the low-carbon transformation of Chinese national industry and achieve high-quality economic development. In this study, we used balanced panel data of 270 Chinese cities from 2005 to 2020 as a research object: (1) to show spatio-temporal evolution patterns in urban industrial carbon emission efficiency; (2) to analyze the aggregation characteristics of industrial carbon emission efficiency in Chinese cities using Global Moran's I statistics; and (3) to use the hierarchical regression model for panel data to assess the non-linear impact of the digital economy on the industrial carbon emission efficiency of cities. The results show the following: (1) the industrial carbon emission efficiency of Chinese cities exhibited an upward trend from 2005 to 2020, with a spatial distribution pattern of high in the south and low in the north; (2) China's urban industrial carbon emission efficiency is characterized by significant spatial autocorrelation, with increasing and stabilizing correlation, and a relatively fixed pattern of spatial agglomeration; (3) there is a significant inverted-U-shaped relationship between the digital economy and the industrial carbon emission efficiency of cities. The digital economy increases carbon emissions and inhibits industrial carbon-emission efficiency in the early stages of development, but inhibits carbon emissions and promotes industrial carbon emission efficiency in mature developmental stages. Therefore, cities at all levels should reduce pollution and carbon emissions from high-energy-consuming and high-polluting enterprises, gradually reduce carbon-intensive industries, and accelerate the digital transformation and upgrading of enterprises. Western, central and eastern regions especially should seek to promote the sharing of innovation resources, strengthen exchanges and interactions relating to scientific and technological innovation, and jointly explore coordinated development routes for the digital economy.

Hydrological connectivity plays a major role in solving water resource and eco-environmental problems. However, this phenomenon has not been afforded the attention it deserves. Detailed analysis of connectivity in river systems could provide considerable insight into structural and functional attributes of riverine landscapes. The current study used graph theory approach and associated connectivity indicators to explore the characteristics and evolution of river systems and hydrological connectivity in a large catchment (Poyang Lake, China). The results revealed that the structure of the river system tended to be complex during 1990-2020, characterized by a dynamic evolution of tributaries in certain northern areas. Both river density and complexity exhibited an increasing trend by up to 15%, with the change rate after 2000 approximately twice as high as that of the preceding period. Overall, human activities across the catchment are more likely to play a key role in leading to significant changes in the quantity, morphometric, and structure characteristics of the river system. Additionally, the functional connectivity analysis indicated that the index of connectivity (IC) in the downstream catchment is stronger than that of the upstream vegetation areas, suggesting a strong contribution to the runoff-sediment transport (r=0.6-0.7). This study highlights the spatial and temporal evolution of both the structural and functional connectivity in the large Poyang Lake catchment. The findings of this work will bene-fit future water resource management and applications by providing a strategy for protecting the surface hydrology and mass transport of large river basins under climate and land-use changes.

In this paper, single and repetitive frequency UIS characteristics of 1200 V asymmetric (AT)and double trench silicon carbide (DT-SiC) metal–oxide-semiconductor field-effect transistors (MOSFETs) under different working conditions are investigated by experiment and simulation. For asymmetric trench SiC MOSFETs, the failure mode is all thermal runaway under working conditions. However, the failure mode of double trench SiC MOSFETs mostly is gate oxide rupture, which indicates an instable avalanche robustness under UIS stress. The variations of measured parameters are recorded to evaluate typical electrical features of device failure. Furthermore, TCAD simulation is used to reveal the electro-thermal stress inside the device during avalanche. Additionally, failed devices are decapsulated to verify the location of failure point from the perspective of the semiconductor die. Finally, a new type of stepped-oxide vertical power DT MOSFET with P-type shielding and current spread layers is proposed for improvement of gate dielectric reliability.

Drug-target affinity (DTA) prediction is crucial for understanding molecular interactions and aiding drug discovery and development. While various computational methods have been proposed for DTA prediction, their predictive accuracy remains limited, failing to delve into the structural nuances of interactions. With increasingly accurate and accessible structure prediction of targets, we developed a novel deep learning model, named S2DTA, to accurately predict DTA by fusing sequence and structural knowledge of drugs, targets, and pockets using heterogeneous models based on graph and semantic networks. Experimental findings underscored that complex feature representations imparted negligible enhancements to the model’s performance. However, the integration of heterogeneous models demonstrably bolstered predictive accuracy. In comparison to three state-of-the-art methodologies, the supremacy of S2DTA became strikingly apparent. It showcased a noteworthy 25.2% reduction in Mean Absolute Error (MAE) and an impressive 20.1% decrease in Root Mean Square Error (RMSE). Furthermore, S2DTA exhibited substantial advancements in other pivotal metrics, including Pearson Correlation Coefficient (PCC), Spearman, Concordance Index (CI), and R2. These metrics experienced remarkable increments of at least 19.6%, 17.5%, 8.1%, and a remarkable 49.4%, respectively. Finally, we conducted interpretability analysis on the effectiveness of S2DTA by bidirectional self-attention mechanism, fully proving that S2DTA is a valuable and accurate tool for predicting DTA. For further exploration, the source data and code repository can be accessed at https://github.com/dldxzx/S2DTA.

The deployment of a manufacturing execution system (MES) holds promising potential in facilitating the accumulation of a substantial amount of inspection data. Low quality levels in discrete manufacturing environments are the result of multi-factor coupling and failure to find quality issues in a timely manner within manufacturing settings may trigger the propagation of defects downstream. Currently, most of the inspection quality methods are direct measurement followed by manual judgment. The integration of deep learning methods provides a feasible way to identify defects in a timely manner, thus improving the acceptance rate of factories. This paper focuses on the design of a data-driven quality prediction and control model around discrete manufacturing characteristics, and use fuzzy theory to evaluate the quality level of production stages. Building Multivariate Long and short-term memory learning hidden quality representations to extract predictions from multi-level inspection data in manufacturing systems. Finally, by validating the data of actual produced water dispensers according to three evaluation indexes, RMSE, MAE, MAPE, the results show that Multivariate Long and short-term memory has better prediction performance.

Urban vitality is an important reflection of a city's development potential and urban quality. This study uses exploratory spatio-temporal big data such as social media check-ins to portray the spatio-temporal evolution of urban vitality at the subdistrict scale in Changsha, a city in central China, from 2013-2021, and finds that urban vitality in Changsha exhibits central agglomeration and outward circling expansion over time; and then use Geodetector and spatial regression analyses are used to explain the interactive effects and spatio-temporal heterogeneity of the spa-tial elements of subdistrict form, subdistrict function and subdistrict economy on urban vi-tality. The results show the following: (1) The subdistrict form and subdistrict function dimen-sions have a significant effect on urban vitality, and the effect of the economic dimension of the subdistrict is not significant. (2) The interaction effect of the density of entertainment and leisure facilities and the density of business office facilities in subdistrict function is the dominant factor in the change of urban vitality. (3) Under the spatio-temporal effect, land use diversity and park facility density have the strongest positive effect on urban vitality; road density and shopping facility density have the weakest effect. The study aims to provide a reference for the optimization and allocation of spatial elements of subdistricts in sustainable urban development and urban renewal, to achieve the purpose of urban vitality creation and enhancement.

This paper presents a novel 3-degrees-of-freedom (3-DOF) haptic master with rubber bands for self-resetting. The mechanical design avoids coupling between three directions mechanically by using three perpendicular axis intersecting at one point. Bevel gear transmission is adopted to increase the compactness of the overall structure. VR-based interactive system is designed and built by incorporating the proposed haptic master. The proposed haptic device can generate force feedback along 3-degree-of-freedom motion using motors and provide command signals to the avatar in the virtual environment. In order to analyze the performance of the developed device in terms of haptic feedback operation, ergonomics assessments are designed and experimentally implemented. Preliminary studies on the influencing factor including the guidance force, the reset force, the speed of the avatar and the arm the length have been conducted. The results of this paper are of great significance for the design of the haptic master and interactive system.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Due to the lack of theoretical research on the amount of spatio-temporal information in the high-speed photography technologies, obtaining an optimized system with a best amount of spatio-temporal information remains a challenge, resulting in insufficient effective information and observation accuracy for ultrafast events. The paper presents an ultrafast raster imaging (URI) system with a large amount of spatio-temporal information based on the all-optical raster principle in single-shot. Specifically, we derive the optimal equation of spatial resolution and the expression for the maximum amount of spatio-temporal information that can achieve excellent performance for an URI system. It serves as a general guideline for getting a large amount of information design in the URI system. Compared to the existing URI systems, the advanced URI system exhibits an improvement of nearly 1 order of magnitude in the amount of spatio-temporal information, and more than twofold in spatial resolution. It shows a great potential for capturing intricate and non-repetitive ultrafast events on the femtosecond time scale.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

For W-band long-range mm-wave wireless transmission systems, nonlinearity issues resulting from photoelectric devices, optical fiber, and wireless power amplifiers can be handled by deep learning equalization algorithms. Besides, the PS technique is considered an effective measure to further increase the capacity of the modulation-constraint channel. However, since the proba-bilistic distribution of m-QAM varies with the amplitude, there have been difficulties in learning valuable information from the minority class. This limits the gain of nonlinear equalization. To overcome the imbalanced machine learning problem, we propose a novel two-lane DNN (TLD) equalizer with the random over-sampling (ROS) technique in this paper. The combination of PS at the transmitter and ROS at the receiver improves the overall performance of the W-band wireless transmission system, and our 4.6-km ROF delivery experiment verifies its effectiveness for the W-band mm-wave PS-16QAM system. Based on our proposed equalization scheme, we realize single-channel 10-Gbaud W-band PS-16QAM wireless transmission over 100 m optical fiber link and 4.6-km wireless air-free distance. The results show that compared with the typical TLD without ROS, the TLD-ROS can improve the receiver sensitivity by 1dB. Furthermore, a reduction of 45.6% in complexity is realized, and training samples can be reduced by 15.5%. Considering the actual wireless physical layer with its requirements, there is much to be gained from the joint use of deep learning and balanced data pre-processing techniques.

Solar assisted hybrid cooling systems are promising for the energy saving of refrigeration systems. In most cases, the solar thermal gain is only able to power the heat-driven process of facilities in part of the working period. Therefore, the reduction of compressor power strongly depends upon the duration of heat-driven processes, which has not been addressed properly. Motivated by such knowledge gap, the thermodynamic understanding of solar assisted hybrid cooling systems is deepened through considering the duration in heat-driven processes. Three absorption-compression integrated cooling cycles were taken as examples. It is found that optimal parameters, e.g., inter-stage pressure and temperature, corresponding to various performance indicators trend to be identical, as the duration of heat-driven processes is taken into account. Furthermore, the optimal parameter for different working conditions was obtained. It is displayed that the dimensionless optimal intermediate temperature of layout with the cascade condensation process varies slightly, e.g., 4%, for different conditions. Moreover, the fall of compressor power in entire working periods is nearly independent upon the intermediate temperature. The paper is favorable for the efficient design and operation of solar assisted hybrid cooling systems.

An increasingly large quantity of primary mineral resource is being converted into manufactured products and destined for solid waste disposal. This material can be reclassified as “anthropogenic mineral reserves” and be a potential source of metals for a range of manufacturing uses. China is implementing a range of policy interventions which can lead to such a classification that will raise the profile of recycling programs as a means of metal supply. China is not only a major producer of consumer products and importer of secondary metals, but also has a major urban infrastructure footprint. Here we consider three product groups, 30 products, and imports, and map the recycling potential of anthropogenic mineral and 23 types of the capsulated materials by targeting their evolution from 2010 to 2050. Total weight of anthropogenic mineral on average in China reached 39 Mt in 2010, but it will double in 2022 and quadruple in 2045. Stocks of precious metals and rare earths will increase faster than most base materials. The total economic potential in yearly-generated anthropogenic mineral is anticipated to grow markedly from 100 billion US$ in 2020 to 400 billion US$ in 2050. Anthropogenic mineral of around 20 materials will be able to meet projected consumption of three product groups by 2050, due to high availability of recycled content and gradual saturation of consumption. Durability of material usage and the concomitant stock of the anthropogenic mineral remain major challenges in determining the viability of this supply in the second half of the coming century.

The heritage of ancient buildings is an important part of the world's history and culture, which has an extremely rich historical-cultural value and artistic research value. Beijing has a large number of palace ancient buildings, and because of the age of their construction, many of them have problems of varying degrees of peeling and mold on the inner surfaces of the envelope. To solve the problems of the damp and moldy interior of palace buildings, a mathematical model of indoor heat and moisture transfer was established based on a wooden palace ancient building in Beijing. Through the indoor mold distribution validation model, the effects of outdoor humidity, soil moisture, wall humidity, and other factors on the indoor heat and moisture transfer of ancient buildings were simulated and analyzed by using the control variables method. The results showed that the molds were distributed at the indoor corners and floors, and the simulation of indoor humidity match the measured humidity. Thus, the simulation results were consistent with the actual situation. The variable trend of the relative humidity of the indoor environment with the outdoor humidity is inconsistent from plane to plane, i.e. it increases or remains constant with the increase of the outdoor humidity. The indoor ambient relative humidity increased with increasing the wall humidity. And the indoor average temperature is 23.3 ℃ and indoor relative humidity ranged between 90.9 % to 92.44 %. Soil moisture and wall humidity were the main factors affecting the indoor environmental relative humidity.

The promotion of plant growth and suppression of plant disease using beneficial microorganisms is considered an alternative to the application of chemical fertilizers or pesticides in the field. In this study, a coconut-scented antagonistic Trichoderma strain LZ42, previously isolated from Genoderma lucidum-cultivated soil, was investigated for biostimulatory and biocontrol functions in tomato seedlings. Morphological and phylogenetic analyses suggested that strain LZ42 is closely related to T. atroviride. Tomato plants showed increased aerial and root dry weights in greenhouse trials after treatment with T. atroviride LZ42 formulated in talc, indicating the biostimulatory function of this fungus. T. atroviride LZ42 effectively suppressed Fusarium wilt disease in tomato seedlings, with an 82.69% control efficiency, which is similar to that of fungicide treatment. The volatile organic compounds (VOCs) emitted by T. atroviride LZ42 were found to affect the primary root growth direction and promote the root growth of tomato seedlings in root Y-tube olfactometer assays. The fungal VOCs from T. atroviride LZ42 were observed to significantly inhibit F. oxysporum in a sandwiched Petri dish assay. SPME-GC-MS analysis revealed several VOCs emitted by T. atroviride LZ42; the dominant compound was tentatively identified as 6-pentyl-2H-pyran-2-one (6-PP). 6-PP exhibited a stronger ability to influence the direction of the primary roots of tomato seedlings but not the length of the primary roots. The inhibitory effect of 6-PP on F. oxysporum was the highest among the tested pure VOCs, showing a 50% effective concentration (EC50) of 5.76 μL mL-1 headspace. In conclusion, T. atroviride LZ42, which emits VOCs with multiple functions, is a promising agent for the biostimulation of vegetable plants and integrated management of Fusarium wilt disease.

In this paper, an intelligent blind guide system based on 2D LiDAR and RGB-D camera sensing is proposed, and the system is mounted on the smart cane. The intelligent guide system relies on 2D LiDAR, RGB-D camera, IMU, GPS, Jetson nano B01, STM32 and other hardware. The main advantage of the intelligent guide system proposed by us is that the distance between the smart cane and obstacles can be measured by 2D LiDAR based on Cartographer algorithm, thus achieving Simultaneous localization and mapping (SLAM). At the same time, through the improved yolov5 algorithm, pedestrians, vehicles, pedestrian crosswalks, traffic lights, warning posts, stone piers, tactile paving and other objects in front of the visually impaired can be quickly and effectively identified. Laser SLAM and improved yolov5 obstacle identification tests were carried out inside a teaching building on the campus of Hainan Normal University and on a pedestrian crossing on Longkun South Road in Haikou City, Hainan Province. The results show that the intelligent guide system developed by us can drive the wheels and omnidirectional wheels at the bottom of the smart cane, and give the smart cane a self-leading blind guide function like a "guide dog", which can effectively guide the visually impaired to avoid obstacles and reach the predetermined destination, and can quickly and effectively identify the obstacles on the way out. The laser SLAM speed of this system is 25~31FPS, which can realize the short-distance obstacle avoidance and navigation function both in indoor and outdoor envionments. The improved yolov5 helps to identify 86 types of objects, the recognition rate for pedestrian crosswalks and for vehicles are 84.6% and 71.8%, respectively; the overall recognition rate for 86 types of objects is 61.2%, and the obstacle recognition rate of the intelligent guide system is 25-26FPS.

This study aimed to evaluate the effects of a palygorskite-based antibacterial agent (PAA) as an alternative to antibiotics on growth performance, blood parameters, rumen fermentation, and rumen microbiota in sheep. A total of 120 sheep were randomly divided into five groups of six replicates with four sheep each. Sheep were fed a basal diet, an antibiotic diet supplemented with 500 g/t chlortetracycline (CTC), and a basal diet supplemented with 500, 1,000, and 2,000 g/t PAA for 80 d, respectively. Supplementation with 2,000 g/t PAA and 500 g/t CTC increased the average daily gain (ADG) of sheep compared with the control group (P < 0.05). Diets supplemented with 2,000 g/t PAA and 500 g/t CTC reduced (P < 0.05) the feed: gain (F/G ratio) in the overall periods. Dietary Supplementation with 1,000 g/t PAA significantly increased albumin and total protein (P < 0.05). A significant positive correlation was found between growth hormone concentration and PAA supplementation (P < 0.05). In addition, compared to the control group, the CTC group had higher growth hormone concentration and lower lipopolysaccharide concentration (P < 0.05). No dif-ference was observed between the five groups in terms of rumen fermentation characteristics (P > 0.05). At the phylum level, the relative abundance of Proteobacteria was lower in the PAA 2000 and CTC 500 groups than that in the control and PAA 500 groups (P < 0.05). At the genus level, a sig-nificant decrease (P < 0.05) in the relative abundance of RuminococcaceaeUCG-010 was observed in the PAA 1000, PAA 2000, and CTC 500 groups compared with that in the control group. In addition, the relative abundance of Prevotella1 (P < 0.05) was higher in the PAA 2000 group than that in the control group. These findings indicate that dietary supplementation with PAA has ameliorative effects on growth performance, blood parameters, and rumen microbiota, with an optimal dosage of 2,000 g/t for sheep.

Peanut (Arachis hypogaea) is a crop plant with high economic value, but the epigenetic regulation of its growth and development has only rarely been studied. The peanut histone deacetylase 1 gene (AhHDA1) has been isolated and is known to be ABA- and drought-responsive. In this paper, we investigate the role of AhHDA1 in more detail, focussing on the effect of altered AhHDA1 expression in hairy roots at both the phenotypic and transcriptional levels. Agrobacterium rhizogenes-mediated transformation of A. hypogaea hairy roots was used to analyse how overexpression or RNA interference of AhHDA1 affects this tissue. In both types of transgenic hairy root, RNA sequencing was adopted to identify genes that were differentially expressed, and these genes were assigned to specific metabolic pathways. AhHDA1-overexpressing hairy roots were growth-retarded after 20 d in vitro cultivation, and superoxide anions and hydrogen peroxide accumulated to a greater extent than in control or RNAi groups. Overexpression of AhHDA1 is likely to accelerate flux through various secondary synthetic metabolic pathways in hairy roots, as well as reduce photosynthesis and oxidative phosphorylation. Genes encoding the critical enzymes caffeoyl-CoA O-methyltransferase (Araip.XGB85) and caffeic acid 3-O-methyltransferase (Araip.Z3XZX) in the phenylpropanoid biosynthesis pathway, chalcone synthase (Araip.B8TJ0) and polyketide reductase (Araip.MKZ27) in the flavonoid biosynthesis pathway, and hydroxyisoflavanone synthase (Araip.0P3RJ) and isoflavone 2'-hydroxylase (Araip.S5EJ7) in the isoflavonoid biosynthesis pathway were significantly upregulated by AhHDA1 overexpression, while their expression in AhHDA1-RNAi and control hairy roots remained at a lower level or was unchanged. Our results suggest that alteration of secondary metabolism activities is related to overexpression of AhHDA1, which is mainly reflected in phenylpropanoid, flavonoid and flavonoid biosynthesis. Future studies will focus on the function of AhHDA1 interacting proteins and their action on cell growth and stress responses.

In order to provide a new direction for the diagnosis and treatment of gastric cancer, the differentially expressed blood-based miRNAs in gastric carcinoma were obtained and analyzed from the datasets GSE113486, GSE112264 and GSE113740 by the SangerBox, the miRNA - target genes prediction, GO and KEGG functional enrichment analyses with DAVID 6.8, and the STRING database with Cytoscape, respectively. The correlation between the key miRNAs expression and the prognosis and diagnostic value of gastric cancer patients were detected by survival prognosis and ROC curve. QRT-PCR was used to detect the possible key miRNAs expression in human blood species. The dataset GSE108307 which shows the miRNAs affected by H. pylori infection was analyzed by GEO2R. The expression level of CagA and the clinically used gastric cancer markers were detected in human blood species for contrast. Five key blood-based miRNAs were determined, including hsa-miR-124-3p, hsa-miR-125a-3p, hsa-miR-29b-3p, hsa-miR-4276, and hsa-miR-575.The detection in human blood species as well as the cross analysis with H. pylori infection and clinically used markers expression suggested the importance and efficacy of the specific miRNAs in the early diagnosis and monitoring of gastric carcinoma. The study identified potential novel blood miRNA biomarkers of gastric cancer by bioinformatics and human blood species detection, which may give a new possibility of the important biomarkers for the diagnosis and prognosis of gastric cancer.

This paper aims to investigate the coal thickness change area of the combined rock strata energy accumulation law. The method of connecting a uniaxial compression experiment with a theoret-ical analysis is used in this work. We employ a combination of coal and rock to carry out our studies. We investigate how different lithologies and ratios of coal-rock height affect the me-chanical properties of the mixture and the law governing energy accumulation. We have deter-mined the following facts: (1) The combination's peak strength and elastic modulus exceed that of coal and are inferior to that of rock but are nearer to that of coal. (2) When the coal-rock height ratios are dissimilar, the peak strength and modulus of elasticity of the combination show a negative correlation with the coal-thickness share, and the pre-peak energy accumulation and impact energy index of the combination shows a positive correlation with the coal-thickness share. (3) For the combination with the same coal-rock height ratio, the peak strength, elastic modulus, pre-peak energy accumulation, and impact energy index all increase with greater rock strength and elastic modulus. The presence of a hard rock layer affects the accumulation of pre-peak energy. ( 4 ) The stress in the surrounding rock gradually decreases as the coal thick-ness increases. In the area where coal thickness declines, the stress in surrounding rock is higher than that in the region where it thickens. The energy stored in the surrounding rock is directly proportional to the coal in the zone. Conversely, areas with thinner coal deposits exhibit a lower energy storage capacity in the surrounding rock than those with thicker coal deposits. The stress distribution of surrounding rock in coal thickness change is abnormal; substantial energy accu-mulation can swiftly initiate dynamic disasters, such as rock bursts. This study has important reference significance for preventing and controlling rock burst in coal thickness change areas.

Federated Distillation (FD) has recently attracted increasing attention for its efficiency in aggregating multiple diverse local models trained from statistically heterogeneous data of distributed clients. Existing FD methods generally treat these models equally by merely computing the average of their output soft predictions for some given input distillation sample, which does not take the diversity across all local models into account, thus leading to degraded performance of the aggregated model, especially when some local models learn little knowledge about the sample. In this paper, we propose a new perspective that treats the local data in each client as a specific domain and design a novel domain knowledge aware federated distillation method, dubbed DaFKD, that can discern the importance of each model to the distillation sample, and thus is able to optimize the ensemble of soft predictions from diverse models. Specifically, we employ a domain discriminator for each client, which is trained to identify the correlation factor between the sample and the corresponding domain. Then, to facilitate the training of the domain discriminator while saving communication costs, we propose sharing its partial parameters with the classification model. Extensive experiments on various datasets and settings show that the proposed method can improve the model accuracy by up to $6.02\%$ compared to state-of-the-art baselines.

To expand the application area of the reference group and enrich exercise theoretical research, based on Stimulus-Organism-Response (S–O-R) framework, this study examines the factors that motivate for adherence to exercise from the external. Taking reference group and strategy and cultural fit as the main stimulus, and personal investment and life satisfaction as mediating variables, this study try to explore the influence of external stimulus on residents’ exercise behavior. In order to enrich the sample size, two surveys of 734 Chinese residents in two cities (Xiamen vs. Fuzhou) were conducted using factor analyses, regression analysis, and T-test analysis. The results indicated that the reference group and strategic and cultural fit as external stimulus have impact on residents’personal investment, life satisfaction and exercise adherence, personal investment and life satisfaction as the organism has impact on residents’ exercise adherence. Personal investment and life satisfaction play a chain mediating role between the reference group and exercise adherence, strategy and cultural fit, and exercise adherence. Moreover, the T-test determined the differences between Xiamen and Fuzhou residents’ exercise adherence and life satisfaction. Residents’ surroundings affect their exercise behavior and life satisfaction. These findings have implications for policymaking aimed at promoting national exercise, which could gradually improve residents’ physical fitness, particularly in light of the current coronavirus emergency.

Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

Chinese investors are easily affected by hot topics on the media and Internet and likely take irrational behavior. They tend to consume rationally and invest emotionally. This research aims to analyze the Baidu index’s effect on share price of solar power industry in China. Three main models are established to identify the correlation between Baidu index and stock price of solar industry. The media index and searching index of Baidu are chosen as an independent variable to measure the influence from media and Internet, and stock price as the dependent variable. To improve and complete the analysis, Hexun index is taken into consideration as mediator variable. This study applied Multiple Linear Regression Model and VAR (Vector auto-regression) Model. The research mainly uses the tools of SPSS, Eviews and Excel to conduct data analysis. The test is based on the theories of Granger Causality, unit root test, F-test, and t-test. The research proves the relationship between the close price of stock and Baidu index, and it also created a model for further forecasting.

Background: Diabetic retinopathy (DR) is one of the most prominent pathological microvascular complications in diabetes. A series of studies reported that vitamin D deficiency was associated with increased prevalence of retinopathy in diabetic patients but the results were inconsistent. In this study we focused on evaluating the relationship between vitamin D deficiency and DR by conducting a meta-analysis of observational studies. Methods: Systematic computerized searches were performed in PubMed, MEDLINE, and the Cochrane Library for relevant original articles till November 20, 2016. The pooled odds ratios (ORs) with corresponding confidence intervals (CIs) were calculated to assess the associated value of vitamin D deficiency to the risk of DR. 9 studies including 6332 participants were subjected to final analysis. Results: The results indicated that vitamin D deficiency increases the risk of DR (OR = 1.57, 95% CI 1.32-1.87) with a little heterogeneity (I2 = 23%). In addition, the subgroup analysis demonstrated that there were obvious heterogeneities in T2DM (I2 = 47.8%). Sensitivity analysis showed that the results were relatively stable and reliable. Conclusion: our meta-analysis demonstrated that vitamin D deficiency could increase the risk of DR.

Nutrients are the driving force of plant and herbivore interactions. Different elements and fertilization levels in soil, or artificially fertilized substrates can have a direct impact on plant defense responses. Meanwhile, nutrient levels mediated by root associated microbes can indirectly affect plant-herbivore interactions. Nutrient uptake promoted by beneficial mycorrhizal fungi or rhizobacteria interacting with roots can stimulate plant tolerance to herbivore attack, as evidenced by herbivore performance, plant nutrient status, plant biomass allocation and compensatory growth. In return, herbivory affects nutrient fluxes between plants and their associated beneficial microbes. Furthermore, aboveground and belowground herbivory can affect the nutrient exchange between plants and soil microbial communities, mainly for carbon-and nitrogen-based resources supporting herbivores´ life cycles. These ecological interactions are governed by jasmonic acid (JA) and key enzymes on the molecular level. This review summarizes the current scientific literature on the role of nutrients in plant-herbivore interactions. This will support efforts to optimize plant defense strategy via managing nutrient variance.

In the context of the rural revitalization strategy, it is urgent to accurately grasp the spatial differentiation characteristics and influencing factors of rural settlements in underdeveloped arid inland river basins. Taking the Shiyang River Basin as an example, the rural settlements from 2000 to 2019 were obtained by visual interpretation using satellite remote sensing data and official statistical data. Following the logical of "state characteristics - evolutionary patterns - influence factors - layout optimization", the average nearest index, gravity-center migration model, spatial statistical analysis and other methods were used combine with GIS. The spatiotemporal pattern evolution characteristics of rural settlements in the past 20 years have been analyzed. The results revealed the following: 1) The distribution pattern of rural settlements in the study area is sheet-like and strip-shaped. The projects in the southeast are mostly distributed in a patchy pattern with high density, while the characteristics in the west and north are exactly opposite. The objects in the south are distributed in the alluvial area of rivers, while settlements in the north are located in the oasis area. 2) From 2000 to 2019, the scale of rural settlements in the Shiyang River Basin, where simultaneous occurrence of new-built and disappearing phenomena, shows an expansion trend that fast firstly and then slow. Spatially, rural settlements in the basin show a trend of clustering towards the southwest. 3) The distribution characteristics of rural settlements are close to water and roads, greatly influenced by urban-rural integration and ecological migration. The results will provide scientific basis for accelerating the modernization of rural areas, and the construction of new rural areas according to local conditions.

Potato (Solanum tuberosum L) gradually becomes a stable food worldwide since it can be treated as practical nutritional supplement and antioxidant, as well as energy provider for human beings. Financially and nutritionally, cultivation and utility of potatoes is worthy enough attention of the world. To further explore functionality and maximize utilization of component parts, also to develop new products based on potato still be an ongoing issue. To maximize the benefits of potato and induce new high-value products while avoiding unfavorable properties of the crop has been a growing trend in food and medical areas. This review intends to summarize the factors that influence the changes in the key functional components of potatoes and discuss referred research focuses, then help further researchers to make efforts into. Afterwards, it summarizes the application of the latest commercial products and potential value of components existing in potato. Particularly, there are several main tasks for the next potato research: preparing starchy foods for special group of people and developing fiber-rich products to supply the dietary fiber intake as well as manufacturing bio-friendly and specific design films/coating in packaging industry; extracting bioactive proteins and potato protease inhibitors with high biological activity, and continue to build new commercial products based on potato protein and examine their health benefits. Noteworthy, the preservation methods play a key role in phytochemicals contents left in foods and potato performs superior to many common vegetables when meeting demand of mineral daily intake and alleviating mineral deficiencies.

Free-edge effect is one of the factors affecting the mechanical properties of three-dimensional woven composites under tensile load. However, current research is relatively poorly understood regarding the effect of free-edge on the stiffness and strength of the material. This paper aims at examining the influence of free-edge effect on the mechanical properties of 3D woven composites under tension through experimental and simulation mathods. The three-dimensional DIC technique is used to collect the full-field strains on the specimen surface during the test, and the stress-strain differences in different regions in the width direction are analyzed, and the overlap of the curves in each region is found to be high. Experimental studies are conducted on specimens of different widths (within the range of 15-20 mm), and the results indicate that the differences in mechanical properties of 3D woven composites under tension loading in this width range are not significant. A progressive damage finite element model is developed for calculation and compared with experimental results.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

In this paper, we present a new stress calculation method for flexible structures, particularly, the tensile armors, and apply it to flexible riser fatigue analysis. The method is based on a 3-dimensional curved bar theory. First, the tensile armor center line was described as a cylindrical helix curve, its bended curve length and bending migration length were derived and studied under different friction scenarios. Second, the tensile and bending stiffness was given with consideration of frictional hysteretic effect, and verified through FEA analysis results. Third, we presented the stress calculation formula for tensile armor under tension and bending load. All stress components are considered, including tensile, bending and shear stresses. Fourth, the method was benchmarked with published experimental results on a flexible prototype tension and bending tests, and comparisons showed general agreements. Fifth, the method is further applied to a 8” flexible riser for fatigue assessment and lifetime extension evaluation, and showed the flexible riser has sufficient remaining fatigue life, and is suitable to continue its service under the current operating conditions. Last, conclusions are drawn. It concluded that the presented tensile armor stress calculation method and modelling techniques are valid for flexible riser fatigue analysis. This method is time efficient, and can be implemented into other multi-scale models for riser dynamic analysis. It is also applicable to other similar helix structure stress analysis, such as wire ropes, submarine hoses, and subsea umbilicals.

The advancement of mass spectrometry technologies has revolutionised plant metabolomics research by enabling the acquisition of raw metabolomics data. However, the identification, analysis, and visualisation of these data require specialised tools. Existing solutions lack a dedicated plant-specific metabolite database and pose usability challenges. To address these limitations, we developed PlantMetSuite, a web-based tool for comprehensive metabolomics analysis and visualisation. PlantMetSuite encompasses interactive bioinformatics tools and databases specifically tailored for plant metabolomics data, facilitating upstream-to-downstream analysis in metabolomics and supporting integrative multi-omics investigations. PlantMetSuite can be accessed directly through a user's browser without the need for installation or programming skills. The tool is freely available at https://plantmetsuite.verygenome.com/ and will undergo regular updates and expansions to incorporate additional libraries and newly published metabolomics analysis methods. The tool's significance lies in empowering researchers with an accessible and customisable platform for unlocking plant metabolomics insights.

Black barley seeds are a health-beneficial diet resource because of their special chemical composition and antioxidant properties. The black lemma and pericarp (BLP) locus was mapped in a genetic interval of 0.807 Mb on chromosome 1H, but its genetic basis remains unknown. In this study, targeted metabolomics and conjunctive analyses of BSA-seq and BSR-seq were used to identify candidate genes of BLP and the precursors of black pigments. The results revealed that five differentially expressed genes identified on the 1H chromosome were candidate genes of the BLP locus, and 17 differential metabolites, including the precursor and repeating unit of allomelanin, were accumulated in the grain-filling stage of black barley. Phenol nitrogen-free precursors such as catechol (protocatechuic aldehyde) or catecholic acids (caffeic, protocatechuic, and gallic acids) may promote black pigmentation. BLP can manipulate the accumulation of benzoic acid derivatives (salicylic acid, 2,4-dihydroxybenzoic acid, gallic acid, gentisic acid, protocatechuic acid, syringic acid, vanillic acid, protocatechuic aldehyde, and syringaldehyde) through the shikimate/chorismite pathway other than the phenylalanine pathway and alter the metabolism of the phenylpropanoid-monolignol branch. Collectively, it is reasonable to infer that black pigmentation in barley is due to allomelanin biosynthesis in lemma and pericarp, and BLP regulates melanogenesis by manipulating the biosynthesis of its precursors.

Raindrop size distribution (RSD) is an index for reflecting precipitation characteristics. Analyzing the differences of RSD plays an important role in understanding the precipitation microphysical processes and improving quantitative precipitation prediction of radar. In this paper, the RSD data of Dafang (57708) station, Majang (57828) station, and Luodian (57916) station (with an altitude of 1722.7m, 985.0m, and 441.5m, respectively) in Guizhou are analyzed according to the precipitation microphysical characteristics. First,Particles with particle size less than 1mm contributes the highest value to the density of particle number , and decrease with the descending altitude. Second, the GAMMA distribution fit shows a better fit compare to M-P distribution fit, and GAMMA distribution fit increases with the ascending altitude. Third, the mass-weighted average diameter is not sensitive enough to the change of precipitation intensity with correlation coefficients of 54.84%, but there is a obvious relationship between the average volume diameter and the precipitation intensity with correlation coefficients of 69.15%. Then, the precipitation prediction model is established using LSTM neural network after fusing the representative microphysical characteristics of RSD with radar and rain gauge data. The precipitation prediction model is applied to the Dafang (57708) site to predict precipitation for time range of 0-180 minutes, and it is found that for the prediction of convective cloud and stratiform cloud precipitation, the 60-minute prediction results are the most consistent with the actual precipitation, where the correlation coefficients are 92.87% and 92.57%, respectively. Conclusively, the results demonstrate that combining with the RSD base data could improve the reliability of precipitation forecasting.

We explored the dynamics of the two interacting information systems. We show that for the Markovian marginal systems the driving force for information dynamics is determined by both the information landscape and information flux. While the information landscape can be used to construct the driving force to describe the equilibrium time reversible information system dynamics, the information flux can be used to describe the nonequilibrium time-irreversible behaviours of the information system dynamics. The information flux explicitly breaks the detailed balance and is a direct measure of the degree of the nonequilibriumness or time irreversibility. We further demonstrate that the mutual information rate between the two subsystems can be decomposed into the equilibrium time-reversible and nonequilibrium time-irreversible parts respectively. This decomposition of the mutual information rate (MIR) corresponds to the information landscape-flux decomposition explicitly when the two subsystems behave as Markov chains. Finally, we uncover the intimate relationship between the nonequilibrium thermodynamics in terms of the entropy production rates and the time-irreversible part of the mutual information rate. We found that this relationship and MIR decomposition still hold for the more general stationary and ergodic cases. We demonstrate the above features with two examples of the bivariate Markov chains.

Although hydrogen gas (H2) treated soil improves crop biomass, this approach appears difficult for the field application due to the flammability of H2 gas. In this report, we investigated whether and how H2 applied in hydrogen nanobubble water (HNW) improves the yield and quality of cherry tomato (Lycopersicon esculentum var. cerasiforme) with/without fertilizers. Two-year field trials showed that compared to corresponding controls, HNW without/with fertilizers improved cherry tomato yield per plant by 39.7% and 26.5% in 2021 (Shanghai), and 39.4% and 28.2% in 2023 (Nanjing). Compared to surface water (SW), HNW increased soil available nitrogen (N), phosphorus (P), and potassium (K) consumption regardless of fertilizer application, which may be attributed to the increased NPK transport related genes in roots (LeAMT2, LePT2, LePT5, and SlHKT1,1). Also, HNW-irrigated cherry tomato displayed higher sugar-acid ratio (8.6%) and lycopene content (22.3%) than SW-irrigated plants without fertilizers. Importantly, the beneficial effects of HNW without fertilizers on yield per plant (9.1%), sugar-acid ratio (31.1%), volatiles (20.0%) and lycopene contents (54.3%) were stronger than those achieved by fertilizers alone. In short, this study clearly indicated that HNW-supplied H2 not only exhibited fertilization effect on enhancing tomato yield, but also improved fruit quality with a lower carbon footprint.

This study aimed to identify miRNA editing sites during adipose tissue development in Ningxiang pigs and analyze their characteristics and functions. Based on the small RNA-seq data from subcutaneous adipose tissue samples of Ningxiang pigs at four stages (30, 90, 150 and 210 days), we constructed a developmental atlas of the miRNA editome in adipose tissue of Ningxiang pigs. The characteristics and functions of this editome were further explored through bioinformatics analysis. The findings revealed that a total of 505 miRNA editing sites were identified with C-to-U editing types being the most prevalent, followed by U-to-C, A-to-G and G-to-U. Importantly, these four types of miRNA editing exhibited a base preference. The number of editing sites showed obvious differences among age groups, with the highest occurrence of miRNA editing events observed at 90 days of age and the lowest at 150 days of age. In the miRNA seed region, a total of 9 miRNA editing sites were identified with significant differences in editing levels (P &lt; 0.05), and located in ssc-miR-23a, ssc-miR-27a, ssc-miR-30b-5p, ssc-miR-15a, ssc-miR-497, ssc-miR-15b, and ssc-miR-425-5p, respectively. Target gene prediction and enrichment analysis revealed that the editing of miR-497 may potentially regulate fat deposition by inhibiting adipose synthesis via influencing target binding. These results provide new insights into the regulatory mechanism of pig fat deposition.

As an essential synthetic material used in continuous casting of steels, mold fluxes improve the surface quality of steel slabs. In this study, a CaO-SiO₂-Na₂O based low-fluorine mold flux was solidified by an improved water-cooled copper probe with different temperatures of molten flux and different probe immersion times. The heat flux through solid films and the film structures were calculated and inspected, respectively. The results indicate: large internal cracks (formed in the glassy layer of films during solidification) were observed, the formation and evolution of those cracks contributed to the the unstable heat flux density. The roughness of the surface in contacted with the water-cooled copper probe formed as films were still glassy and the roughness have no causal relationship with crystallization or devitrification. Combeite with columnar and faceted dendritic shapes is the main crystal in the film.

Novel coronavirus infection is a recent infective agent that causes severe potentially fatal pneumonia. The clinical presentation includes asymptomatic infection, severe pneumonia, and acute respiratory failure. Data pertaining to the clinical presentation of solid organ transplant recipients are scarce. Two cases of novel coronavirus infection in two recipients of renal transplant with variable clinical presentations and outcomes are reported. The first patient presented with progressive respiratory symptoms, acute renal failure, and passed away, whereas the second one, although presented with respiratory tract symptoms and hypoxemia remained stable and exhibited an excellent clinical recovery despite recent reception of thymoglobulin induction. This paper reports rare cases of novel coronavirus infection in renal transplant recipients. For an enhanced insight of the novel coronavirus infection and acute kidney injury on the clinical presentation, severity, and outcome in solid organ transplant recipients, further investigations are required.

In this study, we evaluated the effects of Cyclosporine A (CsA) on Lipopolysaccharide (LPS)-induced cytokine production in the genital tract of female rabbits. Twelve sexually mature and healthy female rabbits were randomly divided into four groups (n = 3 each). The rabbits in the LPS group were given an intrauterine infusion of Escherichia coli LPS (4 mg/kg body weight (BW)). Rabbits in the CsA group were given CsA (20 mg/kg BW). Rabbits in the LPS + CsA group were given LPS (4 mg/kg BW) and CsA (20 mg/kg BW). The control group received only LPS and CsA carrier. The gene expression and protein levels of pro- and anti-inflammatory cytokines were observed using qRT-PCR and immuno-histochemical (IHC) assay, respectively. Our study showed that IL-1β, IL-6, IL-8, TNF-α, IFN-γ, IL-4, IL-10, IL-13, and TGF-β were expressed in female genital organs. The LPS challenge increased the mRNA expression of IL-6 and TNF-α in the uterine body and IL-1β in the uterotubal junction compared to the control group. CsA increased the basal mRNA expression of anti-inflammatory cytokines (i.e., IL-4 in the uterine body, uterotubal junction, and oviductal ampulla; IL-10 in the cervix, oviductal isthmus, and ampulla; and TGF-β in the uterotubal junction and oviductal ampulla) and pro-inflammatory cytokines (i.e., IL-6 and IL-8 in the cervix; IL-1β in the oviductal isthmus; TNF-α in the oviductal ampulla; and IFN-γ in the uterine body compared to the control group). In addition, CsA inhibited the mRNA expression of pro-inflammatory cytokines, such as IL-6 in the uterine body, uterotubal junction, and oviductal isthmus; TNF-α in the uterine body; and IFN-γ in the uterotubal junction and oviductal isthmus induced by the LPS challenge. The IHC assay showed the LPS-induced increase in protein production of IL-6 in the uterine body and oviductal isthmus. CsA increased the protein production of IL-10 in the cervix, uterine body, oviductal ampulla, and isthmus. Moreover, CsA decreased the protein production of IL-6 in the uterine body and oviductal isthmus induced by LPS.

. In this paper, we introduce a series of definitions of generalized affine functions for vector-valued functions. We prove that our generalized affine functions have some similar properties with generalized convex functions. We present examples to show that our generalized affinenesses are different from one another, and also provide an example to show that our definition of presubaffinelikeness is non-trivial; presubaffinelikeness is the weakest generalized affineness introduced in this article. We work with optimization problems that are defined and taking values in linear topological spaces. We devote to the study of constraint qualifications, and derive some optimality conditions as well as a strong duality theorem. Our optimization problems have inequality constraints, equality constrains and abstract constraints; our inequality constraints are generalized convex functions and equality constraints are generalized affine functions.

In this paper, we prove that the sub convexlikeness introduced by V. Jeyakumar [1], and the subconvexlikeness defined in V. Jeyakumar [2] are equivalent in loccallly convex topological spaces. And then, we work with set-valued vector optimization problems and obtain some vector saddle-point theorems and vector Lagrangian theorems.

General wisdom thinks that the central of blackholes are singular and featured by mass, charge and spin exclusively; the microstate reflected in the Bekenstein-Hawking entropy can be accounted for only in some quantum gravity. We challenge this wisdom with two exact solution families to the sourceful Einstein equation which describe dust ball with oscillatory inner structure and variety of mass profiles. We attribute the matter content's oscillation across the central point of the system to the forward scattering domination in high energy collisions induced by inter-gravitating acceleration and provide their Penrose-Carter diagram representation and quantum description briefly. Our solution family provides a very simple semi-classic picture for the micorstate definition of black holes.

Private vehicle travel is the most basic mode of transportation, and the effective control of the real-world fuel consumption rate of light-duty vehicles plays a vital role in promoting sustainable economic development as well as achieving a green low-carbon society. Therefore, the impact factors of individual carbon emission must be elucidated. This study builds five different models to estimate real-world fuel consumption rate of light-duty vehicles in China. The results reveal that the Light Gradient Boosting Machine (LightGBM) model performs better than the linear regression, Naïve Bayes regression, Neural Network regression, and Decision Tree regression models, with mean absolute error of 0.911 L/100 km, mean absolute percentage error of 10.4%, mean square error of 1.536, and R squared (R2) of 0.642. This study also assesses a large number of factors, from which three most important factors are extracted, namely, reference fuel consumption rate value, engine power and light-duty vehicle brand. Furthermore, a comparative analysis reveals that the vehicle factors with greater impact on real-world fuel consumption rate are vehicle brand, engine power, and engine displacement. Average air pressure, average temperature, and sunshine time are the three most important climate factors.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Accurate lithium battery diagnosis and prognosis is critical to increase penetration of electric vehicles and grid-tied storage systems. They are both complex due to the intricate, nonlinear, and path-dependent nature of battery degradation. Data-driven models are anticipated to play a significant role in the behavioral prediction of dynamical systems such as batteries. However, they are often limited by the amount of training data available. In this work, we generated the first big data comprehensive synthetic datasets to train diagnosis and prognosis algorithms. The proof-of-concept datasets are over three orders of magnitude larger than what is currently available in the literature. With benchmark datasets, results from different studies could be easily equated, and the performance of different algorithms can be compared, enhanced, and analyzed extensively. This will expend critical capabilities of current AI algorithms, tools, and techniques to predict scientific data.

Li₂MnO₃ is critical component in the well-studied Li-excess cathode materials xLi₂MnO₃•(1- x)LiMO₂ for achieving high lithium storage capacity. In this article, the diffusion of Li ions in Li₂MnO₃ is studied using molecular dynamics (MD) simulation with well-behaved empirical force fields obtained by fitting against the crystal structure from experiment and phonons calculated using Density Function Theory (DFT). We have found two possible tetrahedral hopping channels, 0-TM and 1-TM(Mn⁴⁺) channel, which are differentiated by the face sharing octahedral cations. Simulation results show that the 0-TM channel is active for Li hopping, while 1-TM(Mn4+) channel is inactive. During the delithiation process, the Li ions in the TM layered are firstly removed, then those in the Li layer. However, the Li ions will be trapped in the tetrahedral 0-TM channels as long as the four face sharing octahedral sites are cleared. Up to x=1.0 for Li₂-xMnO₃, almost all the Li ions are located at the tetrahedral sites, forming a regular array along a axis. The de-intercalation of tetrahedral Li ions requires a high voltage (>5.2 V vs. Li/Li+), limiting the practical capacities measured in lab. The diffusion of Mn ions into the Li layers is observed in a deeper delithiated structure (x=1.2 for Li₂-xMnO₃), indicating an initial phase transformation to a spinel-like structure. However, the Mn ions are mainly trapped in the tetrahedral sites in the Li layer, instead of the octahedral sites fin spinel-like structure. A few of Mn ions diffusing into the octahedral sites in Li layers have no face sharing tetrahedral Li ions, revealing a further Li de-intercalation is imperative for the complete phase transformation. Our model is not stable for x≥1.4 in Li₂-xMnO₃. Other charge compensation mechanism should be considered in this high delithiation stage, eg. oxygen release.

In this paper, mineralogical and elemental geochemical characteristics of massive sulfide samples collected from Jade hydrothermal field, located in the Izena depression in the central graben of Okinawa Trough, were analyzed by means of optical microscopy, scanning electron microscopy and electron probe. The results show that the sulfide in Jade hydrothermal area can be divided into Zn-Cu-Pb rich massive sulfide and Zn-Fe rich massive sulfide. The former is composed of sphalerite, galena, anglesite, chalcopyrite and pyrite, and its formation stage can be divided into pyrite stage, sphalerite-chalcopyrite stage, anglesite stage and colloidal pyrite stage. The latter is mainly composed of sphalerite, pyrite, marcasite and a small amount of galena, which can be divided into galena stage, pyrite stage, sphalerite stage, pyrite and marcasite stage. Cu and Zn in pyrite may exist in the form of microinclusions, while Ag and Pb may exist in pyrite in the form of fine galena inclusions containing Ag. Fe and Cu may enter sphalerite in the form of ion replacement. Zn may enter chalcopyrite in the form of ion replacement, and As and Pb may be inclusions in chalcopyrite as As-bearing galena inclusions. Consistent with the previous understanding, the metal elements in the hydrothermal liquid system in Jade hydrothermal field mostly migrate with the hydrothermal fluid as sulfur complexes, and when the hydrothermal fluid mixes with seawater, the physical and chemical conditions of the fluid change, resulting in sulfide mineral precipitation. However, the chemical structure of chalcopyrite is still controversial, which restricts the understanding of the substitution mechanism of trace elements during chalcopyrite precipitation.

In this paper we study the class of mixed-index time fractional differential equations in which different components of the problem have different time fractional derivatives on the left hand side. We prove a theorem on the solution of the linear system of equations, which collapses to the well-known Mittag-Leffler solution in the case the indices are the same, and also generalises the solution of the so-called linear sequential class of time fractional problems. We also investigate the asymptotic stability properties of this class of problems using Laplace transforms and show how Laplace transforms can be used to write solutions as linear combinations of generalisedMittag-Leffler functions in some cases. Finally we illustrate our results with some numerical simulations.

Fire is a serious security threat that can lead to casualties, property damage, and environmental damage. However, despite the availability of object detection algorithms, challenges persist in detecting fires and smoke. These challenges include slow convergence speed, poor performance in detecting small targets, and high computational cost limiting deployments. In this paper, Fire smoke and human detection based on ConvNeXt and Mixed encoder (FCM-DETR), an end-to-end object detection algorithm based on Deformable DETR, is proposed. Firstly, we introduce ConvNeXt to take the place of Resnet, which greatly reduces the amount of computation and improves the ability to extract irregular flame features. Secondly, to effectively process multi-scale features, the original encoder is decoupled into two modules. Then Mixed encoder, an innovative encoder structure, is proposed, resulting in excellent performance of multi-scale fire and smoke features fusion. What can’t be overlooked is that the encoder block is compatible with any DETR-based models. Finally, the convergence speed is accelerated and the mean of average precision is improved by applying a novel loss function called Powerful IoU v2. The experimental results indicate that our model achieves the best detection accuracy compared to other models, with mAP reaching 66.7%, mAPs and Accuracyfire achieving impressive 50.2% and 98.05%, respectively.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

Malaxidinae is one of the confusing groups with classification in Orchidaceae. Previous phylogenetic analysis reveals that the relationships among the taxa in Malaxidinae have not yet been reliably established using a few plastome regions or nuclear ribosomal internal transcribed spacer (nrITS). In the present study, the complete plastomes of Oberonia integerrima and Crepidium purpureum were assembled using high-throughput sequencing. Combined with publicly available complete plastome data, this resulted in a data set of 19 plastomes, including 17 species of Malaxidinae. The plastome feature and phylogenetic relationship were compared and analyzed. The results showed that: (1) The plastomes of Malaxidinae species possessed the quadripartite structure of typical angiosperms, with sizes ranging from 142,996 bp to 158,787 bp and encoding from 125 to 133 genes. The ndh genes were lost or pseudogenized with varying degrees in six species. An unusal inversion was detected in the Large Single-Copy region (LSC) of Oberonioides microtatantha. (2) A total of 8 regions, including ycf1, matK, rps16, rpl32, ccsA-ndhD, clpP-psbB, trn-FGAA-ndhJ, and trnSGCU-trnGUCC, were identified as mutational hotspots. (3) Based on complete plastomes, 68 protein-coding genes and 51 intergenic regions, respectively, the phylogenetic analyses resolved genera-level relationships in this subtribe with strong support. The Liparis was supported as polyphyletic.

The purpose of this study was to see how dietary supplementation with phenylpyruvate affected broiler chicken growth, slaughter performance, gut health microbiota, and immunity. A total of 288 day old broiler chickens were randomly assigned to one of four groups (6 replicates each with 12 chicken). NC (basal diet), PC (basal diet plus antibiotic virginiamycin 15ppm), LCP and HCP (basal diet plus phenylpyruvate 1kg/t and 2kg/t, respectively). Results showed that PC had higher ADFI during the first 21 days, and better FCR than the NC, the LCP and HCP also improved broilers’ FCR 0.001 and 0.037% in relation to NC respectively. HCP has a higher all-eviscerated ratio than NC and less abdominal fat than LCP. HCP has increased villus length and crypt depth in the ileum compared to the NC. Bursa was lower in HCP and thymus was lower in LCP and PC. In contrast HCP have lower pro-inflammatory cytokine IL-1, as well as lower TLR4. The phenylpyruvate improved family Selenomonadaceae, genus Megamonas Bacteroides species that are known for beneficial effects like for maintenance of the cell surface structure, regulating aromatic amino acids and C. jejuni-suppressive treatment respectively. Finally, phenylpyruvate feed supplement can be utilized to improve growth performance and positively modulate gut microbiota, however this is less efficient than antibiotics in improving growth performance, although more efficient in improving productive performance and gut morphology. Moreover, high dose of phenylpyruvate is more effective than low dose

High-quality rice (Oryza sativa L.) is increasingly widely planted in China with the improvement of people's living standards and the achievement of rice breeding efforts in recent years. However, the agronomic and physiological performances of high-quality indica rice (HQIR) under different nitrogen(N) application conditions in southern China are little known. Two-year consecutive field experiments were conducted with two HQIR and two ordinary-quality indica rice (OQIR) varieties under moderate and high N application rates, with yield and yield components, biomass, N up-take, and their related traits investigated. We found that grain yields of HQIR were slightly de-creased, but grain yields of OQIR were significantly increased by 6.60%-8.88% under high N rate compared with moderate N rate in both years. Thereby, OQIR produced 8.34%-11.87% and 22.00%-22.50% higher grain yield than HQIR under moderate and high N rates, respectively. The different responses of grain yield to N application rates were mainly due to decreased grain set-ting rate in HQIR and increased spikelets m-2 in OQIR under high N rate. Furthermore, high N rate significantly reduced pre-anthesis AE and improved grain-leaf area ratio, while did not in-crease post-anthesis DM compared with moderate N rate in HQIR, which might result in carbon metabolic deterioration and imbalance of source-sink relationship and subsequently lower supply of carbohydrate to panicle. Our results suggest that a moderate N rate (165 kg N ha-1) is beneficial for HQIR varieties to balance the maximum grain yield and high quality in southern China

In this study, we analyzed the optical observations of a subluminous Type Ia supernova (SN Ia) 2017fzw, which exhibited high photospheric velocity (HV) at B-band maximum light. The absolute B-band peak magnitude was determined to be M^B_max = -17.77  0.10 mag, similar to 91bg-like SNe Ia. The decline rate of the B-band light curve was estimated to be Dm15(B) = 1.60  0.06 mag. The spectra of SN 2017fzw were similar to those of 91bg-like SNe Ia, with prominent Ti II and Si II l5972 features at early phases, gradually transitioning to spectra resembling normal (mainly HV subclass) SNe Ia at later phases, with a stronger Ca II NIR feature. Notably, SN 2017fzw exhibited spectral evolution features similar to those of HV SNe Ia at all phases, with a maximum-light Si II l6355 velocity of 13, 786  414 km s

Lead-free copper halide perovskite nanocrystals (NCs) are emerging materials with excellent photoelectric properties. Herein, we present a colloidal synthesis route of orthorhombic Cs2CuCl4 NCs with well-defined cubic shape and an average diameter of 24 ± 2.1 nm. The Cs2CuCl4 NCs exhibit bright deep blue photoluminescence, which is attributed to the Cu(II) defects. In addition, passivating the Cs2CuCl4 NCs by Ag+ can effectively improve the photoluminescence quantum yield (PLQY) and environmental stability.

China is rich in coal resources, but the complex hydrogeological conditions lead to difficulties in coal mining, such as coal mine collapse, roof and water damage, and other accidents that occur frequently, resulting in many casualties and property losses. The use of coal mine hole detection technology to detect and analyze the internal environment of the coal mine in advance helps to reduce safety hazards and prevent coal mine accidents, for the existing coal mine hole detection technology operation is cumbersome, not easy to control, and insufficient depth of jacking prob-lems, this paper designs a new type of mine hole detection small robot. Firstly, this paper ana-lyzes the function and structural design of the mine hole detection robot, designs the variable diameter function according to the characteristics of narrow and uneven mine holes in coal mines, and analyzes the mechanics of the critical parts through theoretical calculations; secondly, based on the three-dimensional modeling software, established the structural model of the small robot for mine hole detection; after that, designed the robot's hardware circuits and control pro-grams for the presence of water and gas inside the mine hole, highlighting the need to carry out a new type of mine hole detection small robot. After that, we designed the robot's hardware circuit and control program, giving particular emphasis to the safety design of the circuit for the pres-ence of water and gas inside the mine hole of the coal mine. Finally, to verify the feasibility of the design program, the basic parameters and function tests of the mine hole detection small robot are carried out. The experimental results show that the mine hole inspection small robot realized by this design can adapt to the working hole diameter from 65 mm to 100 mm, the maximum working power is only 12 W, and the maximum crawling speed is 3.96 m/min. The maximum crawling slope reaches 90°, which can meet the actual mine hole inspection needs. The research can provide theoretical and design guidance for developing the mine hole detection robot with substantial engineering practical reference value.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

Molecular dynamics (MD) simulations present a sophisticated nano-scale computational approach that can play a critical role in material design for next generation batteries. One critical piece of information needed for MD simulations is the non-bonded potential parameters, which can be obtained through quantum mechanics (QM) calculations or experimental methods. However, experimental data is not available for exploratory and novel materials to derive the potential parameters. Also, the QM approach needs significant computational power and is too time consuming for large systems. On the other hand, current Artificial Intelligence techniques are faster, but they cannot be generalized across molecules and properties. As a result, there is a significant barrier to discovering and exploring new materials. Overcoming this barrier, in this work, we propose a Machine Learning (ML) based technique that can learn inter-atomic potential parameters for various particle-particle interactions employing QM calculations. This ML model can be used as an alternative for QM calculations for predicting non-bonded interactions in a computationally efficient manner. Using these parameters as input to MD simulations, we can predict a diverse range of properties, enabling researchers to design new and novel materials suitable for various applications in the absence of experimental data. We employ our ML-based technique to learn the Buckingham potential, a non-bonded interatomic potential. Subsequently, we utilize these predicted values to compute the densities of four distinct molecules, achieving an accuracy exceeding 93%. This serves as a strong demonstration of the efficacy of our proposed approach.

The development of novel porous composite materials for organic dye degradation and removal has received increasing attention due to water contamination problem. In this paper, hydrothermal synthesized nano zeolite A have been encapsulated with porous periodic mesoporous organosilica (PMO) through a simple modified StÖber method an organosilane-directed growth-induced etching strategy, the obtained yolk-shell structured sample was further functionalized by the impregnation of copper, realizing the composite material with hierarchical porous and catalytic properties. The morphology, porosity and metal content of the zeolite Cu/A and Cu/A@Et-PMO were fully characterized. As compared to the parent material, the composite Cu/A@Et-PMO have an efficient adsorption and catalytic degradation performance on methylene blue (MB), the removal efficiency reached as high as 95% of 60 mg/L MB with 10min. These novel structured porous composites may have great potential for adsorption and degradation application including waste effluents.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

The sexual reproduction of ascomycetes is controlled by the mating-type(MAT) locus. (Pseudo)homothallic reproduction has been hypothesized based on genetic data from Hirsutella sinensis (Genotype #1 of Ophiocordyceps sinensis). In this study, the differential occurrence of the mating-type genes in the MAT1-1 and MAT1-2 idiomorphs, which constitute the genetic control of O. sinensis reproduction, was analyzed in 237 strains and 5 genomes of H. sinensis. The mating-type genes were differentially transcribed in H. sinensis Strain L0106, and the MAT1-2-1 transcript in H. sinensis Strain 1229 was alternatively spliced, with an unspliced intron I containing stop codons; these findings constitute O. sinensis reproduction controls at the transcriptional and coupled transcriptional-translational levels. The occurrence of the mating-type genes and a-/α-pheromone receptor genes differed among the 5 H. sinensis genomes. The differential occurrence and transcription of these genes are inconsistent with self-fertilization under (pseudo)homothallism but suggest self-sterility of H. sinensis, which therefore needs a mating partner to achieve sexual outcrossing under heterothallism or hybridization. Consistent occurrence and transcription of the mating-type genes of both the MAT1-1 and MAT1-2 idiomorphs have been reported in natural and cultivated Cordyceps sinensis, but these findings are insufficient to determine the reproduction mode(s) because of the co-occurrence of >90 fungal species and multiple genomically independent genotypes of O. sinensis. The mutant MAT1-1-1 and α-pheromone receptor transcripts in natural C. sinensis result in the N-terminus or middle-truncated proteins, with changes in hydrophobicity and secondary structures of the proteins, suggesting heterogeneous fungal source(s) of the proteins and hybridization reproduction.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

Artificial Intelligence (AI) is a breakthrough technology that has been widely applied in many fields and its use in pharmacy is also gaining increasing attentions. Recently, ChatGPT, a newly developed virtual assistant and large language model, is showing strong ability in writing, which makes it a potential tool for review writing. Here in our study, we employ the public available ChatGPT and try to instruct it to generate a mini review on the topic of “lipid-based drug delivery systems” by conversation. Our results showed that ChatGPT can give reasonable outline for this topic and give seemingly sentences with concluding wording, which can give useful information to the readers. However, the accuracy and consistence of the review are not fully guaranteed and there is lack of reliable citations. Therefore, it is concluded that ChatGPT can only give general knowledge on the selected topic, but not capable of giving in-depth discussion. The generated review article can be a useful but occasionally unprecise electronic encyclopedia instead of rigorous scientific literature, which can give benefit for pharmaceutical education and interchange to some extent.

The agamid lizard Phrynocephalus melanurus, is restricted to the Northwest China (Dzungar Basin) and adjacent Eastern Kazakhstan (Zaisan and Alakol basins). To elucidate the phylogeography of P. melanurus, we obtained the mitochondrial DNA COI segments of 175 sampled lizards from 44 localities across the whole distribution range. Phylogenetic analyses revealed two main clades comprising six geographically structured lineages (I, IIa, IIb, IIc1, IIc2, and IIc3) that fits an isola-tion by distance (IBD) model. The divergence from the most recent ancestor was dated to ~1.86 million years ago (Ma). Demographic analyses demonstrated lineage-specific response to past climate change: stable population for Clade I, IIb and IIc2; while past population expansion for IIc1 and IIc3 since 0.02 Ma and 0.18 Ma, respectively. Bayesian phylogeographic diffusion anal-yses detected initial spreading at the Saur Mount vicinity approximately 1.8 Ma. Historical species distribution modeling (SDM) projected expansion of the suitable habitat in the last interglacial period and stepwise contraction in the Last Glacial Maximum and Holocene epochs. The SDM predicts a shrinkage and shift of suitable area eastward as a response to future climate change. Our findings suggest that the evolution of P. melanurus followed a parapatric divergence with subsequent dispersal and adaptation to cold and dry environments during the Quaternary. Moreover, future conservation strategies need to be taken to maintain the population of lineage IIc1.

East Lake in Wuhan, China, harbors a high number of freshwater fish species of great conservation value, concurrently serving as vital resources for local livelihoods. However, the ecosystem is threatened by an array of anthropogenic activities, thus requiring consistent monitoring of the local fish community to enable more efficacious conservation management. In place of conventional surveying methods, we undertook the first analysis of the fish distribution within East Lake via metabarcoding of environmental DNA (eDNA). The accuracy and efficacy of eDNA metabarcoding relies heavily upon selecting an appropriate primer set for PCR amplification. Given the varying environmental conditions and taxonomic diversity across distinct study systems, it remains a challenge to propose an optimal genetic marker for universal use. Thus, it becomes necessary to select PCR primers suitable for the composition of fish in the East Lake. Here, we evaluated the performance of two primer sets, Mifish-U and Metafish, designed to amplify 12S rRNA barcoding genes in fishes. Our results detected a total of 116 taxonomic units and 51 fish species, with beta diversity analysis indicating significant differences in community structure diversity between the 6 sampling locations encompassing East Lake. While it was difficult to accurately compare the species-level discriminatory power and amplification bias of the two primers, Mifish outperformed Metafish in terms of taxonomic specificity for fish taxa and reproducibility. These findings will assist with primer selection for eDNA-based fish monitoring and biodiversity conservation in the East Lake and other freshwater ecosystems.

Lucky bamboo (Dracaena sanderiana hort. ex Mast. = Dracaena braunii) is a domestic species widely cultivated for ornamental purposes in China. In March 2022, a severe occurrence of anthracnose disease was observed on the stems of lucky bamboo plants in a greenery retail store located in Nanjing, Jiangsu Province, China. The morphological characteristics of isolates obtained from diseased stem tissues were identical with those described for Colletotrichum species. Based on multilocus phylogenetic analysis with the internal transcribed spacer (ITS), actin (ACT) gene, and glyceraldehyde-3-phosphate dehydrogenase (GAPDH) gene, the pathogen was identified as Colleto-trichum gloeosporioides (Penz.) Penz. & Sacc. Pathogenicity was verified by mycelial plug-inoculating stem cuttings of one-year-old lucky bamboo plants and spray-inoculating whole one-year-old lucky bamboo plants, respectively. Koch’s postulates were fulfilled by the re-isolation of C. gloeosporioides from symptomatic tissues. To the best of our knowledge, this report describes the first time that C. gloeosporioides was observed to cause anthracnose on lucky bamboo in China.

Multi-source image registration often suffered from great radiation and geometric differences. Specifically, gray scale and texture from similar landforms in different source images often show significantly different visual features. And these differences disturb the corresponding point extraction in the following image registration process. Considering that edges between heterogeneous images can provide homogeneous information and more consistent features can be extracted based on image edges, an edge consistency radiation-change insensitive feature transform (EC-RIFT) method is proposed in this paper. Firstly, the noise and texture interference are reduced by preprocessing according to the image characteristics. Secondly, image edges are extracted based on phase congruency, and an orthogonal Log-Gabor filter is performed to replace the global algorithm. Finally, the descriptors are built with logarithmic partition of the feature point neighborhood, which improves the robustness of descriptors. Comparative experiments on datasets containing multi-source remote sensing image pairs show that the proposed EC-RIFT method outperforms other registration methods in terms of precision and effectiveness.

Saiga (Saiga tatarica) was extirpated in China. Since Mid-1980s, attempts have been made for revival the species in the country, however, only a breeding herd of Saiga was successfully established at Wuwei, Gansu, China. The reintroduced Saiga population experienced a bumpy growth. Then, the population collapsed following the catastrophe die-off in the Saiga ranging countries in Central Asia, then population started to rebound when 6 new lams were born in 2019. After reviewing the population trend and conservation breeding of Saiga in China, we concluded that to establish a migratory species that needs vast range size like Saiga on central Asia steppe, an international collaboration is needed for introducing new genes. We recommend China to ratify the CMS in order to facilitate international conservation efforts to restoring the species in its former range.

Bulbophyllum is one of the largest genera and presents some of the most intricate taxonomic problems in the family Orchidaceae, including species of ornamental and medical importance. The lack of knowledge regarding the characterization of Bulbophyllum chloroplast (cp) genomes has imposed current limitations on our study. Here, we reported the complete cp genomes of seven Bulbophyllum species, including B. ambrosia, B. crassipes, B. farreri, B. hamatum, B. shanicum, B. triste and B. violaceolabellum, and compared with related taxa to provide a better understanding of their genomic information on taxonomy and phylogeny. A total of 28 Bulbophyllum cp genomes exhibit typical quadripartite structures with lengths ranging from 145,092 bp to 165,812 bp and GC content of 36.60% to 38.04%. Each genome contained 125–132 genes, encompassing 74–86 protein-coding genes, 38 tRNA genes, and eight rRNA genes. The genome arrangements, gene contents and length were similar with differences observed in ndh gene composition. A total of 18–49 long repeats and 38–80 simple sequence repeats (SSRs) were detected and the single-nucleotide (A/T) was dominant in Bulbophyllum cp genomes, with an obvious A/T preference. An analysis of relative synonymous codon usage (RSCU) revealed Leucine (Leu) was the most frequently used codon, while cysteine (Cys) was the least used. Six highly variable regions including ndhF-trnLUAG, trnTUGU-trnLUAA, trnFGAA-ndhJ, rps15-trnNGUU, rbcL-accD and psbI-trnSGCU were identified based on the ranking of the Pi values, had the potential to serve as DNA markers for species identification and phylogeny of the genus Bulbophyllum. Phylogenetic analysis based on the complete cp genome sequences and 68 protein-coding genes strongly supported 28 Bulbophyllum species can be divided into four branches and sects. Brachyantha, Cirrhopetalum, Leopardinae defined by morphology were non-monophyly. Our results enriched the genetic resources of Bulbophyllum species, providing valuable information to illustrate the complicated taxonomy, phylogeny and evolution process of the genus.

In recent times, there has been significant enthusiasm for the development of all solid state batteries. This interest stems from a dual focus on safety—addressing concerns related to toxic and flammable organic liquid electrolytes—and the pursuit of high energy density. \cite{SCHNELL2018160,Zheng2018}. While liquid electrolyte batteries constitute for now the vast majority of commercial cells, solid electrolyte batteries show great promise. In parallel with experimental research, computational models \cite{GrazioliEtAlCM2016} clarify the several fundamental physics \cite{LiMonroeARCBM2020} that take place throughout battery operations. We review some classical models, emphasizing the conceptual advancements documented in the most recent works.

The possibility of using graphane monolayer crystals as the electrode material is becoming popular. Graphane is stable at room temperature and has large surface area, but its chemical inertness hinders its direct interactions with Li ions. In this study, we performed density functional theory calculations to study the energetic stability, structural and electronic properties of Li on graphane with various CH divacancy configurations (v12, v13 and v14 ). The results show that adsorption of Li atom reduces the formation energy of the CH divacancy configurations. The Li-v12 is most stable with the highest binding energy of 3.25 eV/Li and relaxes to in-plane with other C atoms. Altering the Li charge state to have Li−1-v12 or Li+1 -v12 affects the energetic stability and electronic characters of Li-v12 . The Li−1-v12 (Li +1-v 12 ) enhances (reduces) the binding force between Li and v 12 configuration, and furthermore it improves (deteriorates) the conductivity of the structure. Further investigation of graphane with vacancies is encouraged due to these intriguing observations, as it holds promise for potential utilization as an electrode material.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

This study examined the tourism spatial distribution of nine cities in the Fujian province and assessed the impacts of COVID-19. The modified gravity model found that it was widely dispersed, with uneven and relatively independent tourism development in different cities. The social network analysis showed that tourism connections across cities were significantly reduced after the pandemic. The impacts of brand awareness and transport accessibility on spatial networks were positive in pre-pandemic but became negative during the pandemic. In contrast, tourist volume had negative impacts on spatial networks in pre-pandemic but had positive ones during the pandemic. Tourism resources and market performance had significantly positive impacts in the post-pandemic era. These findings provide advice on tourism recovery and destination management in coping with future critical events. It also contributes to the theoretical gravity framework in tourism and the research scope of the social networks analysis at the city level.

To reveal the antibacterial effect of wound secretions of different Chinese fir strains on five kinds of bacteria. Three 3-year-old seedlings of Taxus chinensis var.koraiensis and Yangkou and the 3-year-old container seedlings of Taxus chinensis var.pendula, Yang061 and Yang020, were used as the research objects. The antibacterial effect of wound secretions was determined by the filter paper diffusion method, and the antibacterial effect was analyzed. Results showed that the wound secretions of different strains of Chinese fir bark had noticeable bacteriostatic effects on Bacillus subtilis, Salmonella paratyphi B, Pseudomonas aeruginosa, Escherichia coli, and Staphylococcus aureus. However, the bacteriostatic effects of different strains of Chinese fir secretions differed. The minimum inhibitory concentrations (MICs) of the wound secretions of different strains of Chinese fir against the five test bacteria differed. The mean MIC of Pseudomonas aeruginosa was the highest, and the mean MIC of Escherichia coli was the lowest. The antibacterial ability of the wound secretions of different Chinese fir strains was mainly determined by the composition of the wound secretions. There was no noticeable relationship with the number of wound secretions.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

Glioblastoma (GBM) is the most common malignant brain tumor in adults. Despite advancements in treatment, the prognosis for patients with GBM remains poor due to its aggressive nature and resistance to therapy. CRISPR-based genetic screening has emerged as a powerful tool for identifying genes crucial for tumor progression and treatment resistance, offering promising targets for tumor therapy. In this review, we provide an overview of the recent advancements in CRISPR-based genetic screening approaches and their applications in GBM. We highlight how these approaches have been used to uncover genetic determinants of GBM progression and susceptibility to various therapies. Furthermore, we discuss ongoing challenges and future directions of CRISPR-based screening methods in advancing GBM research.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

Nutrition therapy is the best solution to human chronic diseases, especially beer and barley which play an important role in human health and civilization. We demonstrated the actional mechanism of functional ingredients in beer and barley to combat chronic diseases, based on PubMed, google, CNKI, and ISI Web of Science databases from 1997 to 2024. Beer is rich in functional ingredients that is a complex of barley malt and hops; the health effect of beer against 26 chronic diseases is highly similar to that of barley, due to molecular mechanism of polyphenols (phenolic acids, flavonoids), melatonin, minerals, bitter acids, vitamins, and peptides. The ancient German Beer Purity Law provides much scientific basis today, especially indirectly supporting the human one cell disease theory. Low purine beer can be produced by enzymatic and biological degradation and adsorption of purines as well as dandelion addition. Functional beer with low purine and high active ingredients made from Beer Purity and barley malt as well as functional foods addition will be the key and important development direction, such as ginger beer and ginseng beer, especially coix-lily beer at the ancestors ca. 9000 years ago. This review paper not only reveals the actional mechanism of beer overcoming human chronic diseases, but also provides scientific basis for the development of functional beer for the prevention and treatment of human chronic diseases.

Despite well-documented health benefits of probiotics Saccharomyces, its application in oral health has not been comprehensively assessed. Dental caries is a transmissible disease initiated by acid production of cariogenic bacteria and yeast, such as Streptococcus mutans and Candida albicans, on tooth enamel and followed by subsequent enamel demineralization. Here, we investigated the effect of two Saccharomyces strains (Saccharomyces boulardii, Saccharomyces cerevisiae) on S. mutans-C. albicans cross-kingdom interactions using a cariogenic planktonic model. Viable cells, pH changes and gene expression were measured. S. cerevisiae and S. boulardii inhibited the growth of C. albicans either in dual-, or multi-species conditions. Saccharomyces also inhibited C. albicans hyphal formation. Furthermore, Saccharomyces reduced the acidity of the culture medium which usually plummeted below pH 5 when S. mutans and C. albicans were present in the model. The presence of Saccharomyces maintained the culture medium above 6 even after overnight incubation, demonstrating a protective potential against dental enamel demineralization. S. boulardii significantly downregulated S. mutans atpD and eno genes expression. Overall, our results shed light on a new promising candidate, Saccharomyces, for dental caries prevention due to its potential to create a less cariogenic environment marked by a neutral pH and reduced growth of C. albicans.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Although the positive relationship between religion and environmental behavior is well-argued, empirical research about the relationship between religion and public pro-environmental behavior is relatively lacking. This paper aims to explore the group differences in the influence of religion on public pro-environmental behavior and the mediating role of environmental risk perception in religion and public pro-environmental behavior. Using the Chinese General Social Survey data in 2013 for empirical analysis, this study’s results show that there are group differences in the impact of religion on public pro-environmental behavior. Women with religious beliefs are more willing to engage in public pro-environmental behavior than those without religious beliefs. Religious believers over the age of 45 are more willing to participate in public pro-environmental behavior than those without religious beliefs. Political participants with religious beliefs are more willing to practice public pro-environmental behavior than those without religious beliefs. In addition, we found that environmental risk perception can act as partial mediation in religious and public pro-environmental behavior. In other words, religious beliefs are deeply embedded in local political and social culture. In order to correctly understand the relationship between religion and public pro-environmental behavior, it is necessary to consider religion in a specific cultural background.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

The average working person can spend between 35-60 hours a week in the workplace, making it an influential place for mental well-being while also being a place for socio-economic contribution. Workplace incivility can diminish positive mental health outcomes and negatively impact work engagement through increased social anxiety. To investigate this, 118 working adults aged between 19 to 67 years old in Singapore were recruited for a survey comprising of demographics questions, the Workplace Incivility Scale, Brief DSM-5 Social Anxiety Disorder Severity Scale, Utrecht Work Engagement Scale-9 over the period of November 2022 to April 2023. Correlational, regression and mediation analysis showed workplace incivility scale scores to significantly pre-dict social anxiety after controlling for covariates, supporting our hypothesis that employees exposed to work-place incivility would have higher levels of social anxiety that mediated work engagement after controlling for age and gender. The findings here show workplace incivility to be a possible intervention target for social anx-iety to reduce negative impacts on work engagement in order to improve employee experience and retention for organizations.

Two-dimensional (2D) of transition metal dichalcogenides (TMDCs) are potential candidates for thermoelectric (TE) applications due to their unique structural properties. In this paper, we constructed an 2D monolayer TMDCs semiconductor γ-PbSn2(X=S, Se, Te) and first-principles calculations and Boltzmann transport theory are used to study the thermoelectric performance. We found that γ-PbSnX2 had an ultra-high carrier mobility up to 4.04×103 cm2V−1s−1 leading to a metal-like electrical conductivity. Meanwhile, γ-PbSnX2 both have high Seebeck coefficients, resulting in high power-factors, and also shows intrinsic low lattice thermal conductivity of 6-8 W/mK at room temperature. The lower lattice thermal conductivity and high power-factors resulted in excellent thermoelectric performance. The high ZT values of γ-PbSnS2 and γ-PbSnSe2 were as high as 2.65 and 2.96 at 900 K, respectively. The result suggests that the monolayer γ-PbSnX2 are better candidates for excellent thermoelectric performance.

As one of the critical state parameters of the battery management system, lithium battery state of charge (SOC) can provide an essential reference for battery safety management, charge/discharge control, and energy management of electric vehicles. To analyze the application of deep learning in electric vehicle power battery SOC estimation, this study reviewed the technical process, common public datasets, and the neural networks used, structural characteristics, advantages and disadvantages of lithium battery SOC estimation in deep learning method. First, the specific technical processes of the deep learning method for SOC estimation were analyzed, including data collection, data preprocessing, feature engineering, model training, and model evaluation. Secondly, the current commonly and publicly used lithium battery dataset was summarized. Then, the input variables, data sets, errors, and advantages and disadvantages of four types of deep learning methods, were concluded using the structure of neural network used for training as the classification criterion. Finally, the challenges and future development directions of lithium battery SOC estimation in deep learning method were explained.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

In this paper the application of recycled Li-ion batteries spent cathode (LIB-SC) combined with NaHCO₃/H₂O₂ system is presented for the first time in the literature as an alternative for degradation of potentially toxic organic molecules. The model pollutant choice was methylene blue molecule. The spent cathode composition corresponds to LiCoO₂, which was proved by the XRD and EDX. Regarding the decolorization of methylene blue solution, the addition of NaHCO₃ in comparison with only H₂O₂ reduces the complete decolorization time in 96%. This reduction occurs because the radical CO₃ is more stable than OH. In this way, the application the system proposed in this article is aimed at solving two major global problems: the disposal of cell phone batteries and the pollution of liquid effluents.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

The model internal year-to-year variability (hereafter, internal variability) is a significant source of uncertainty when estimating anthropogenic aerosol effective radiative forcing (ERF). In this study, we investigate the impact of internal variability using large ensemble simulations (600 years in total) with the same climate model under prescribed anthropogenic aerosol forcings. A comparison of the magnitudes (i.e., standard deviation, Std) of these influences confirms that internal variability has negligible impacts on the instantaneous radiative forcing (RF) diagnosed by double radiation calls but has considerable impacts on estimating ERF through rapid adjustments (ADJ). Approximately half of the model grids exhibit strong internal variability influence on ERF (Std &gt; 5 W m−2). These strong internal variabilities lead to a 50% probability that 30-year linear change can reach 2 W m−2, and 10-year linear change can reach 4 W m−2. A 50-year simulation can provide a relatively stable annual mean map of ERF (ERF = ADJ + RF), but it fails for ADJ. The statistically significant areas in the annual mean maps of both ERF and ADJ from a 10-year simulation exhibit instability with evident chaotic features. These analyses contribute to the setup of comparative experiments and a more comprehensive understanding of the modeled anthropogenic aerosol ERF.

The Marchenko method is a data-driven way which makes it possible to calculate Green's functions from virtual points in the subsurface by the reflection data at the surface, only requiring a macro velocity model. This method requires collocated sources and receivers. However, in practice, subsampling of sources or receivers will cause gaps and distortions in the obtained focusing functions and Green's functions. To solve this problem, this paper proposes to integrate sparse inversion into the iterative Marchenko scheme. Specifically, we add sparsity constraints to the Marchenko equations and apply sparse inversion during the iterative process. Our work not only reduces the strict requirements on acquisition geometries, but also avoids the complexity and instability of direct inversion for Marchenko equations. This new method is applied to a two-dimensional numerical example with irregular sampled data. The result shows that it can effectively fill gaps of the obtained focusing functions and Green's functions in the Marchenko method.