The welding and construction processes of H-type thick-plate-bridge steel involve complex multi-pass welding processes, which is difficulty to ensure its welding performance. Accordingly, it is crucial to explore the inherent correlation among the welding processes parameters and welding quality, and applied it into the welding robots, eliminating the instability from manual welding. In order to improve the welding quality, the GMAW (Gas Metal Arc Welding) welding process parameters are simulated using the Q345qD bridge steel flat joint model. Four welds with X-shaped grooves are designed to optimize the parameters of welding current, welding voltage, and welding speed. The optimal welding process parameters are investigated through thermal-elastic-plastic simulation analysis and experimental verification. The results indicate that when the welding current is set to 230A, the welding voltage to 32V, and the welding speed to 0.003m/s, the maximum deformation of the welded plate is 0.52mm, with a maximum welding residual stress of 345MPa. Both the simulation results of multi-pass welding and experimental tests meet the welding requirements, as they show no excessive stress or strain. These parameters can be applied into building large steel frame bridges with welding robots, improving the quality of welded joints.

Soil temperature reflects the impact of local factors，such as vegetation，soil and the atmosphere of a region. Therefore, it is important to understand the regional variation of soil temperature. However, lack of observations with adequate spatial and/or temporal coverage, it would be difficult to use the observation data to study the regional variation. Based on the observation data from Nanchang and Ganzhou stations and ERA-Interim/Land reanalysis data, this study analyzed the temporal-spatial distribution characteristics of soil temperature over Poyang Lake Basin. The results showed close correlations between observation data and reanalysis data at different depths. Reanalysis data could mainly reproduce the temporal-spatial distributions of soil temperature over the Poyang Lake Basin, but generally underestimate their magnitudes. Temporally, there is an obvious warming trend in the basin. Seasonally, the temperature raised fastest in spring and slowest in summer, except for the ST4, which rising fastest in spring and slowest in winter. In terms of depths, the temperature of ST1 rises fastest. For the other layers, the warming trend is almost similar. An abrupt change of annual soil temperature at all depths occurred in 1997, and annual soil temperatures at all depths were abnormally low in 1984. Spatially, annual soil temperature decreased with latitude, except for the summer ST1. Because of the high temperature and precipitation in summer, the ST1 are higher around the lake and the river. The climatic trend of soil temperature presents the general increase trend from south to north, opposite to the distribution of soil temperature. The findings provide a basis for understanding and assessing the variation of the soil temperature over the Poyang Lake Basin.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

Background: As the opioid epidemic continues, understanding the geospatial, temporal and demand patterns is important for policymakers to assign resources and interdict individual, organization, and country-level bad actors. Methods: GIS geospatial-temporal analysis and extreme-gradient boosted random forests evaluate ICD-10 F11 opioid-related admissions and admission rates using geospatial analysis, demand analysis, and explanatory models, respectively. The period of analysis was January 2016 through September 2018. Results: The analysis shows existing high opioid admissions in Chicago and New Jersey with emerging areas in Atlanta, Salt Lake City, Phoenix, and Las Vegas. High rates of admission (claims per 10,000 population) exist in the Appalachian area and on the Northeastern seaboard. Explanatory models suggest that hospital overall workload and financial variables might be used for allocating opioid-related treatment funds effectively. Gradient-boosted random forest models accounted for 87.8% of the variability of claims on blinded 20% test data. Conclusions: Based on the GIS analysis, opioid admissions appear to have spread geographically, while higher frequency rates are still found in some regions. Interdiction efforts require demand-analysis such as that provided in this study to allocate scarce resources for supply-side and demand-side interdiction: prevention, treatment, and enforcement. Based on GIS analysis, the opioid epidemic is likely to spread or diffuse through the country, and interdiction efforts require demand-analysis such as that provided in this study to allocate scarce resources for supply-side and demand-side interdiction: prevention, treatment, and enforcement.

Marine mortar was the goal material and its multi-scale physical-chemical-mechanical characteristics were the principal interest in this study. The on-line multi-scale damage detection experiments art was designed to quantify the characteristics mathematically and graphically. The normal cylinder specimen with 70-day age was produced and investigated by dynamically global MSHCT scan and local detection of EDS, SEM and XRD. The experiments results indicated that the marine mortar offered the appreciable strength at the early age at least, although some saline minerals were generated during the preparation. The micro-interfacial behavior and the parental foci controlled the damage development of the marine mortar the performance of which was still the adjustable one by the composition optimization.

There are four subtypes of adenosine receptors (ARs), named A1, A2A, A2B and A3, all of which are G protein-coupled receptors. The A2BAR, coupled to both Gαi and Gαq G proteins, is one of the several G-protein-coupled receptors that are expressed in a significantly higher level in some cancer tissues in comparison to adjacent normal tissues. There is growing evidence that the A2BAR plays an important role in tumor cell proliferation, angiogenesis, metastasis, and immune suppression. Thus, A2BAR antagonists are potentially novel attractive anticancer agents. Several antagonists targeting at the A2BAR are currently in clinical trials for various types of cancers. In this review, we first describe the signaling, agonists, and antagonists of the A2BAR. We further discuss the role of the A2BAR in the progression of various types cancers, and the rationale of using A2BAR antagonists in cancer therapy

In this work we study the recently developed parametrized partition function formulation and show how we can infer the thermodynamic properties of fermions based on numerical simulation of bosons and distinguishable particles at various temperatures. In particular, we show that in the three dimensional space defined by energy, temperature and the parameter characterizing parametrized partition function, we can map the energies of bosons and distinguishable particles to fermionic energies through constant-energy contours. We apply this idea to both noninteracting and interacting Fermi systems and show it is possible to infer the fermionic energies at all temperatures, thus providing a practical and efficient approach to obtain thermodynamic properties of large fermion systems with numerical simulation. As an example, we present energies for up to 50 noninteracting fermions and up to 20 interacting fermions at all temperatures and show good agreement with the analytical result for noninteracting case.

Background: Plasma levels of von Willebrand factor (VWF) are significantly elevated in patients with COVID-19. However, the dynamic changes and prognostic value of this biomarker in hospitalized patients with COVID-19 are not determined. Methods: 124 patients infected with SARS-CoV2 were prospectively recruited for the study. Serial blood samples were obtained at the time of admission (D1), 3-4 days following standard of care treatments (D2), and 1-2 days prior to discharge or death (D3). Plasma VWF antigen, ADAMTS13 antigen and activity, as well as the ratio of VWF/ADAMTS13 were determined, followed by statistical analyses. Results:While admission plasma levels of VWF in COVID-19 patients were significantly elevated, no statistical significance was detected among patients of different disease severity. Plasma ADAMTS13 activity, but not its antigen levels, were significantly lower in patients with severe or critical COVID-19 compared with other groups. Interestingly, the ratios of plasma VWF antigen to ADAMTS13 antigen were significantly higher in patients with severe or critical COVID-19 than in those with mild to moderate disease. More importantly, plasma levels of VWF and VWF/ADAMTS13 ratios were persistently elevated in patients with COVID-19 during hospitalization. Kaplan-Meier and Cox proportional hazard regression analysis revealed that an increased plasma VWF or ratio of VWF/ADAMTS13 at D2 and D3 associated with an increased mortality rate. Conclusions: Persistent endotheliopathy, marked by an elevated level of plasma VWF or an increased VWF/ADAMTS13 ratio, is present in all hospitalized patients following SARS-CoV2 infection and strongly associated with mortality.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

As an important means of controlling the spread of cities, large-scale urban green belts have been widely used in the planning and construction of green space systems in various mega-size cities around the world. In previous studies, there has been more research on the overall isolation effect of green belts, while there has been less research on changes in their internal structure. There have been more perspectives on the land-use change (LUC) caused by urban expansion, and less systematic research on the dual driving factors of LUC. In this paper, we constructed a multi-dimensional index system to measure the "contraction-expansion" mechanism of land use in the overlapping vegetation areas of large green belts under the dual influence of urban expansion and urban greening, from the perspectives of quantity, space, and connectivity during different construction periods. Taking the boundary of two green belts in Beijing as an example, we hope to provide scientific support for the construction and ecological protection of Beijing's green belts.

Tao and Ming (name) or Tao and Yan (language or speech) is an inseparable pair of important concepts in traditional Chinese language philosophy. In LaoTze’s opinion, Tao could not be spoken out, and language or speech could not reach Tao’s essence. Yan and Tao are separated from each other, and they are paradoxical. All the confusion derives from Yan regardless of how delicate they are. Tao can be expressed in words, but it will never be expressed through common languages. In this article, Tao is regarded as a human being’s thoughts or intentions and is even considered to be the origin of the real world. Language can express people’s thought, although it has some limitations. There exist some contradictions between the real word and the world expressed in words. To enable people to better understand the existence of the real world from multiple perspectives at the language or linguistic level without being constrained by words, this article studies LaoTze’s linguistic philosophy reflected in his opinion on the relationship between Tao and Yan and makes a comparative analysis of modern Western language philosophers’ stand on language (or speech) and existence.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

At present, there are still no specific therapeutic drugs and appropriate vaccines for Dengue. Therefore, it is very important to explore distinct clinical diagnostic indicators. In this study, we combined differentially expressed genes (DEGs) analysis and weighted co-expression network analysis (WGCNA) to screen a stable and robust biomarker which can be used to distinguish three clinical stages of Dengue and severity of Dengue. CD38 can distinguish excellently Early Acute, Late Acute, Convalescent stages for Dengue patients, and ZNF595 can discriminate DHF from DF in whole acute stages. We also found that three clinical stages can be discriminated based on the fractions of Plasma cells, activated memory CD4+ T cells, and Monocytes. In different clinical stages different immune cells function positively. Negative inhibition of viral replication based on Gene Ontology (GO) enrichment, Kyoto Encyclopedia of Genes and Genomes (KEGG) analysis and Gene set enrichment analysis (GSEA), up-regulated autophagy genes and impairing immune system are potential reasons resulting in dengue hemorrhagic fever (DHF).

A novel metal-doped carbon quantum dot, zinc-chlorine co-doped carbon quantum dots (Zn/Cl-CQDs), has been developed for the fluorescent probe detection of vitamin B2 and the analysis of the correlation properties of this carbon quantum dot and vitamin B2. Stability experiments demonstrate that Zn/Cl-CQDs possess good fluorescence properties under alkaline conditions. However, when vitamin B2 is added into Zn/Cl-CQDs, the fluorescence intensity decreases sharply, indicating that a fluorescence quenching phenomenon occurs between vitamin B2 and Zn/Cl-CQDs. Lastly, the use of Zn/Cl-CQDs in the detection of vitamin B2 tablets and vitamin B2-rich fruits resulted in recovery rates of 98.2% and 100.6%, respectively. Therefore, this method can be well applied to the detection and analysis of vitamin B2, and has great development prospects in the pharmaceutical industry and food monitoring fields.

We consider the conjecture of the relationship between the entanglement entropy of spacetime, matter and the action in Einstein's general relativity. Our analysis suggests the possibility of regarding the entanglement entropy of spacetime and matter as the dimensionless action in general relativity by using Planck units. In this case, the action principle originates from the maximization of the entanglement entropy. We also show that the fundamental property of entanglement entropy leads to attractive characteristic of gravitational force for classical particles.

We consider the quantum thermodynamic origin of the gravitational force of matter by applying the spacetime entanglement entropy and the Unruh effect originating from vacuum quantum fluctuations. By analyzing both the local thermal equilibrium and quasi-static processes of a system, we may get both the magnitude and direction of Newton's gravitational force in our theoretical model. Our work shows the possibility that the elusive Unruh effect has already shown its manifestation through gravitational force.

The apple leaf-curling midge, Dasineura mali Kieffer (Diptera: Cecidomyiidae), is an invasive pest of apple. To provide crucial information for its pest risk analysis, forecast and management, we investigated the effects of temperatures (5, 10, 15, 20 and 25°C) and daylengths (10, 11, 12, 13, 14 and 15 hrs) on its development and survival. The midge could not complete its development at 10°C or lower. After transferred from 20°C to 10°C, mature larvae could survive for about two months and develop to adults. Pupation and emergence rates were significantly higher at 20°C than at 10°C and 25°C. Daylength had no effect on these parameters. The low temperature threshold and thermal requirement to complete development from eggs to adults were 3.7°C and 627 degree-days, respectively. The midge had significantly lower thermal requirement for completion of its lifecycle at 20°C (614.5 degree-days) than at 15°C (650.1 degree-days) and 25°C (634.8 degree-days). The thermal model developed in this study provided accurate predictions of the number of D. mali generations and adult emergence time in each generation in different regions of New Zealand. We suggest that the model could be used to predict population dynamics of this pest in other parts of the world.

In this study, a new method for synthesizing Au-NaYF4:Yb3+/Er3+-DSPE-PEG2K nanocomposites was introduced. Using a hydrothermal method, the synthesized Yb3+- and Er3+-codoped NaYF4 upconversion luminescent materials and Au nanoparticles were doped into upconversion nanomaterials and modified with DSPE-PEG2k up-conversion nanomaterials. This material is known as Ag-UCNPs-DSPE-PEG2k, it improves both the luminous intensity because of the doped Au nanoparticles and has low cytotoxicity because of the DSPE-PEG2k modified. Exciting UCNPs with a wavelength of 980nm near-infrared light will emit light with a wavelength of 520nm to further excite gold nanoparticles to convert light energy into heat. Successful synthesized gold nanoparticles was confirmed using transmission electron microscopy (TEM). The morphology of UCNPs was observed using scanning electron microscopy (SEM), and the mapping confirmed the successful doping of Au nanoparticles. Fluorescence spectra were used to compare changes in luminescence intensity before and after doping Au nanoparticles. The cytotoxicity of Au-UCNPs-DSPE-PEG2K was tested via the cell counting kit-8 (CCK-8) method, and its imaging ability was characterized using the Magnetic Resonance Imaging (MRI) and Computed Tomography (CT) method.

Transverse momentum spectra of +, p, Λ, Ξ or ¯Ξ+, Ω or ¯Ω+ and deuteron (d) in different centrality intervals in Gold-Gold (Au-Au) and Lead-Lead (Pb-Pb) collisions at 62.4 GeV and 2.76 TeV respectively, are analyzed by the blast wave model with Boltzmann Gibbs statistics. We extracted Kinetic freeze out temperature,transverse flow velocity and kinetic freezeout volume from the transverse momentum spectra of the particles. It is observed that the non-strange and strange (multi-strange) particles freezeout separately due to different reaction cross-sections. While the freezeout volume and transverse flow velocity are mass dependent which decrease with the rest mass of the particles. The present work reveals the scenario of double kinetic freezeout in collisions at STAR and ALICE Collaborations. Furthermore, the kinetic freezeout temperature and freezeout volume are larger in central collisions than the peripheral collisions and they decrease from central to periphery. However the transverse flow velocity remains almost unchanged from central to peripheral collisions.

Due to the advantages of low latency, low power consumption and high flexibility of FPGA-based acceleration technology, it has been more and more widely studied and applied in the field of computer vision in recent years. An FPGA-based feature extraction and tracking accelerator for real-time visual odometry (VO) and visual simultaneous localization and mapping (V-SLAM) is proposed, which can realize the complete acceleration processing capability of the image front-end and directly output the feature point ID and coordinates to the backend. The accelerator consists of image preprocessing, pyramid processing, optical flow processing, and feature extraction and tracking modules. For the first time, it implements a hardware solution that combines features from accelerated segment test (FAST) corners with Gunnar Farneback (GF) dense optical flow, to achieve better feature tracking performance and provide more flexible technical route selection. In order to solve the scale invariance and rotation invariance lacking problem of FAST features, an efficient pyramid module with a five-layer thumbnail structure is designed and implemented. The accelerator is implemented on a modern Xilinx Zynq FPGA. The evaluation result shows that the accelerator can achieve stable tracking of features of violently shaking images, and is consistent with the results of MATLAB code running on PC. When operating at 100MHz, the accelerator can process 108 frames per second for 720P images and 48 frames per second for 1080P images. Compared to PC CPUs that consume seconds of time, the processing latency is greatly reduced to the order of milliseconds, making GF dense optical flow an efficient and practical technical solution on the edge side.

Carboxypeptidase A4 (CPA4) has shown the potential possibility as a biomarker in the early diagnosis for certain cancers. However, no previous research has linked CPA4 to therapeutic or prognostic significance in bladder cancer. Using data from The Cancer Genome Atlas (TCGA) database, we set out to determine the full extent of the link between CPA4 and BLCA. We further analyzed the interacting proteins of CPA4 and infiltrated immune cells via TIMER2，STRING and GEPIA2 databases. The expression of CPA4 in tumor and normal tissues was compared using the TCGA+GETx database. The connection between CPA44 expression and clinicopathologic characteristics and overall survival (OS) was investigated using multivariate methods and Kaplan-Meier survival curves. The potential functions and pathways were investigated via gene set enrichment analysis. Furthermore, we analyze the associations between CPA4 expression and infiltrated immune cells with their respective gene marker sets using the ssGSEA, TIMER2, and GEPIA2 databases. Compared to matching normal tissues, human CPA4 was found to be substantially expressed. We confirmed that overexpression of CPA4 is linked with shorter OS, DSF, PFI, and increased diagnostic potential using Kaplan-Meier and ROC analysis. The expression of CPA4 is related to T-bet, IL12RB2, CTLA4, and LAG3, among which T-bet and IL12RB2 are Th1 marker genes, while CTLA4 and LAG3 are related to T cell exhaustion, which may be used to guide the application of checkpoint blockade and the adoption of T cell transfer therapy.

Oil has become the object of global exploits and fierce competition among the major world powers as it is a key strategic non-renewable resource. Transnational petroleum investment is therefore an important mechanism available to countries and international corporations to control oil resources even though there are numerous inherent uncertainties and risks. A new risk assessment index system is proposed in this paper based on use of the Delphi expert scoring system and fuzzy comprehensive evaluation that aims to minimize the potential risks inherent to multinational petroleum investment. This approach encapsulates political, legal, socioeconomic, and infrastructural factors to develop a technical method that can be used for transnational petroleum investment risk assessment. An evaluation of oil investment risk within a case study area is also presented; results provide reference data that can be applied by national and international oil companies to mitigate risks of transnational oil investment.

An adaptive spatial clustering (ASC) algorithm is proposed in this present study, which employs sweep-circle techniques and a dynamic threshold setting based on the Gestalt theory to detect spatial clusters. The proposed algorithm can automatically discover clusters in one pass, rather than through the modification of the initial model (for example, a minimal spanning tree, Delaunay triangulation or Voronoi diagram). It can quickly identify arbitrarily-shaped clusters while adapting efficiently to non-homogeneous density characteristics of spatial data, without the need of prior knowledge or parameters. The proposed algorithm is also ideal for use in data streaming technology with dynamic characteristics flowing in the form of spatial clustering in large data sets.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

The current study emphasizes on optimizing a suitable ratio of enzymatically hydrolyzed potato powder (EHPP) and whole milk powder (WMP) to produce a quality yogurt by evaluating the physicochemical and rheological properties. The results showed that the addition of EHPP decreased the pH towards acidic conditions which resulted in the high acidity of yoghurt. The proximate composition showed that EHPP increased the ash, protein, water holding capacity (WHC) while fat, synersis, color parameters and total solid were decreased when compared to control yoghurt (CY) sample. Moreover, texture profile (TPA) analysis showed that the addition of EHPP decreased the hardness and cohesiveness while springiness did not show significant difference. Furthermore, rheological properties revealed that EHPP decreased the storage modulus (G’) and loss modulus (G”) when compared with control. In addition to this, sensory analysis revealed that the treatment P4M (1:3) was found as optimum ratio regarding taste, flavor, and aroma. Besides this, scanning electron microscopy (SEM) confirms that the high amount of EHPP resulted in the void holes while CY showed dense gel structure. The prepared yogurt with EHPP provides an excellent flavor, satisfying sweetness and homogeneous texture. These findings suggest the optimum formulation ratio of prepared yogurt was found to be P4M (1:3) for desirable attributes and consumer acceptance. The prepared yogurt from the EHPP presents the potential industrial applications.

This paper investigates the influence of different vegetation on the permeability of the shallow soil layers of slopes under rainfall infiltration. Firstly, four large slopes are filled in the outdoor natural environment, and the overburdens of the four slopes are Magnolia multiflora, Cynodon dactylon, Magnolia multiflora mixed with Cynodon dactylon, and no vegetation. Secondly, the four slopes are cultivated in the outdoor natural environment for one year. After the vegetation overburdens are matured, the field artificial rainfall test is carried out through the self-developed artificial rainfall device to monitor the water migration law inside the four slopes in real time. Finally, the unsaturated permeability coefficients of the shallow soil layers of slopes are calculated. The results show that the infiltration rate of rainwater in each overburden slope from fast to slow is Magnolia multiflora overburden slope, no vegetation slope, Cynodon dactylon overburden slope, Magnolia multiflora mixed with Cynodon dactylon overburden slope. In the early stage of rainfall, Magnolia multiflora increases the permeability coefficient of the shallow soil layer of the slope, thus weakening the anti-seepage ability of the slope, but the influence of Magnolia multiflora is not obvious in the later stage. Cynodon dactylon and Magnolia multiflora mixed with Cynodon dactylon can significantly reduce the permeability coefficient of the shallow soil layers of the slopes, thereby increasing the anti-seepage ability of the slopes, and the mixed planting of Magnolia multiflora and Cynodon dactylon can minimize the permeability coefficient of the shallow soil of the slope, resulting in the best anti-seepage effect.

Thermal interface material (TIM) that can exist as liquid at the service temperature enables efficient heat transfer across two adjacent surfaces in electronic applications. In this work, the thermal conductivities of different phase regions in the Ga-In system at various compositions and temperatures are measured for the first time. A modified comparative cut bar technique is used for the measurement of the thermal conductivities of In_xGa_1-x (x=0, 0.1, 0.214, 0.3, and 0.9) alloys at 40, 60, 80, and 100^oC that are the temperatures commonly encountered in consumer electronics. The thermal conductivity values for the liquid and semi-liquid (liquid+β) Ga-In alloys are higher than the TIM currently used in consumer electronics. These measured quantities, along with the available experimental data from the literature, served as input for the thermal conductivity parameter optimization using the CALPHAD (CALculation of PHase Diagram) method for the pure elements, solution phase, and two-phase region. A set of self-consistent parameters for the description of the thermal conductivity of the Ga-In system is obtained. There is good agreement between the measured and calculated thermal conductivity values for all the phases. Hence, it can be envisaged that liquid/semi-liquid Ga-In alloys can be considered as a potential TIM in consumer electronics due to its high thermal conductivity.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

In this study, a new method for synthesizing Ag-NaYF4:Yb3+/Er3+ @ SiO2 nanocomposites was introduced. Using a hydrothermal method, the synthesized Yb3+- and Er3+-codoped NaYF4 upconversion luminescent materials and Ag nanoparticles were doped into upconversion nanomaterials and coated with SiO2 up-conversion nanomaterials. This material is known as Ag-UCNPs-SiO2’ it improves both the luminous intensity because of the doped Ag nanoparticles and has low cytotoxicity because of the SiO2 coating. The morphology of UCNPs was observed using scanning electron microscopy (SEM), and the mapping confirmed the successful doping of Ag nanoparticles. Successful coating of SiO2 was confirmed using transmission electron microscopy (TEM). Fluorescence spectra were used to compare changes in luminescence intensity before and after doping Ag nanoparticles. The reason for the increase in luminescence intensity after doping with Ag nanoparticles was simulated using first-principles calculations. The cytotoxicity of Ag-UCNPs-SiO2 was tested via the cell counting kit-8 (CCK-8) method, and its imaging ability was characterized using the micro-CT method.

Carbon fiber insole (CFI), which is lightweight and stiff to reduce energy loss and help wearers perform better in sports, has recently been introduced. However, there are scarce reports on the effects of CFI on sports performance, muscle fatigue and wearing comfort. This study investigat-ed the short-term effects of CFI on sports performance, lower extremity muscle activity, and sub-jective comfort. Thirty young healthy males performed various sports tasks and treadmill runs with wearable sensors under two experimental insole conditions (benchmark insole as a baseline, CFI). The results showed that compared to the benchmark insole, CFI significantly improved sports performance in terms of power generation and agility. However, it activated more of the Tibialis Anterior and Gastrocnemius Medialis muscles and was perceived stiffer, and less com-fortable. These findings suggested that CFI can improve sports performance, but it could cause more lower extremity muscle fatigue and subjective discomfort.

In order to perform multi-degree-of-freedom motion measurements of marine machinery such as ship-borne mechanical platform in an absolute environment without a reference, absolute measurement methods using acceleration sensors and tilt gyroscopes are typically employed. However, due to the influence of wave forces on ship-borne mechanical platform, the coupling between different degrees of freedom can cause mutual interference, resulting in significant sensor measurement disturbances that make efficient computation and real-time analysis challenging. Specifically, when ship-borne mechanical platform swings, the proof mass of the acceleration sensor produces an undesirable signal output in the vertical direction, which leads to imprecise acceleration integration, thereby affecting accurate motion collection and posture estimation. To address these challenges, by analyzing the influence of the inclination angle of the ship-borne mechanical platform on the sensor measurement, and using the working principle of the acceleration sensor and angle sensor, a correction method for the motion measurement of the ship-borne mechanical platform based on multi-sensor fusion is proposed. In this article, we first analyze the influence of inclination angle on the integral effect in the heave direction. Then the configuration using four groups of acceleration sensors to correct the integral effect is proposed. Finally, the optimal inclination angle is determined through Kalman filtering based on the measured value of angle sensors and estimated values from the acceleration sensor sets. Experiments have proved that the average error of the corrected heave displacement signal is 25.34 mm, which is better than the integral displacement signal of a single acceleration sensor. At the same time, the acceleration sensor is used to calculate the roll angle and pitch angle of the ship-borne mechanical platform, and combined with the angle sensor signal to perform Kalman filtering, which filters out the errors caused by the shaking and instability of the mechanical platform, and can more accurately estimate the true inclination of the platform. Therefore, this method can enhance the precision and accuracy of the ship-borne mechanical platform motion signal acquisition, providing more valuable experimental data for research in marine engineering and related fields.

The challenging terrain and deep ravines characteristic of mountainous regions often result in slower path planning and suboptimal flight paths for Unmanned Aerial Vehicles (UAVs) when traditional meta-heuristic optimization algorithms are employed. This study investigates the application of an Improved Enhanced Snake Optimizer (IESO) for three-dimensional path planning in a simulated rugged mountainous terrain. The initialization process in the enhanced snake optimizer is refined by integrating the Chebyshev chaotic map. Additionally, a non-monotonic factor is introduced to modulate the "temperature," and a boundary condition is incorporated into the dynamic opposition learning mechanism. These modifications collectively reduce the likelihood of population convergence to local optima during optimization. The feasibility of IESO is validated through time complexity and global convergence analyses. Comparative simulation experiments benchmarked IESO against five state-of-the-art optimization algorithms across test functions and path-planning simulated scenarios. The experimental results indicate that the enhanced algorithm achieves superior optimization precision, faster convergence speeds, and improved quality in the planned trajectories by 30%.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Chinese Taihe Black-bone silky fowl (TBsf) is the homology of medicine and food and has high nutritional and medical value all over the world. However, the nutritional compositions and specific metabolite advantages of Taihe silky fowl muscle are still poorly understood. In this study, we investigated the differences of nutritional components between TBsf and another similar breed (Black Feathered chicken and laid green-shelled eggs, BF-gsc). Meanwhile, we also explored the divergences in muscle characteristics of Taihe silky fowl fed with two different diets, that is normal chicken feed (TBsf-ncf) and Broussonetia papyrifera-fermented feed (TBsf-bpf). Firstly, the growth performance and biochemical index of Taihe silky fowl was significantly different compared with black-feathered chicken. Secondly, we identified the metabolic alterations in Taihe silky fowl by performing an un-targeted UHPLC-Q-TOF-MS/MS analysis. Our results suggested that the whole metabonomic characteristics had obvious separation between TBsf-ncf, TBsf-bpf and BF-gsc groups both in the positive and negative ion mode by PCA analysis. Next, OPLS-DA multivariate analysis revealed that 57 metabolites (in positive mode) and 49 metabolites (in negative mode) were identified as differential metabolites between TBsf-ncf and BF-gsc group. These differential metabolites were mainly enriched to ABC transporters, biosynthesis of amino acids and aminoacyl-tRNA biosynthesis. Besides, there were 47 metabolites (in positive) and 13 metabolites (in negative) were differentially regulated between TBsf-ncf and TBsf-bpf group, which were majorly involved in histidine metabolism and linoleic metabolism. Furthermore, the integrated network analysis suggested that DL-arginine, DL-isoleucine, linoleoylcarnitine, stearoylcarnitine (positive) and ricionleic acid, D-proline, uric acid (negative) were the significantly metabolic biomarkers in Taihe silky fowl. Moreover, the metabolites of primaquine, ticlpoidine, riboflavin, acetylcarnitine (positive) and salicylic acid, acetaminophen sulfate, glutamic acid (negative) were markedly changed in the Taihe silky fowl fed with BP-fermented feed. In summary, a global survey of the nutritional components and metabolite differences were performed in muscle tissues of Taihe silky fowl between various breeds and feeds. The comprehensive expression profiles of the metabolites in Taihe silky fowl affected by genetic and environmental factors were acquired. This study provided valuable evidence fo breed and feed-induced putative biomarkers as well as improved the economic value of Taihe silky fowl through targeted metabolite regulation.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

Material identification based on R_value (transparency natural logarithm ratio of low-energy to high-energy) of line-scan dual-energy X-ray transmission (DE-XRT) has a good prospect for industrial application. Unfortunately, the DE-XRT signals before attenuation cannot be directly measured, whereas their precision is very important to R_value. Therefore, a context-based signal synthesis method which takes the filtered signals that remove high-frequency noises and retain low-frequency actual fluctuations as the reference value, and takes into account the vertical (forward/column) direction and horizontal (scanning/row) direction anisotropy of line-scan images was proposed. The vertical is a time series with continuity of signal trend; the horizontal is a spatial characteristic with the fluctuation synchronization within the same row signals. The special synthesis evaluations of curve synthesis difference and surface synthesis difference were also proposed. Experimental results show that the tow evaluations are both only about 0.0007, and it only takes 35 ms to complete the surface synthesis of 119×119 pixels on the CPU with 3.4 GHz main frequency. The presented method can achieve high signal synthesis precision and calculation real-time, so as to facilitate DE-XRT material identification. It can be extended to improve the precision of numerical synthesis in other line-scan uncomplete signals.

(1) Background: Substantial evidence that neural timing deficits are prevalent in developmental disorders, aging, and concussions resulting from a mild Traumatic Brain Injury (mTBI) is presented. We show that if timing deficits are remediated using low-level movement discrimination training, then high-level cognitive skills, including reading, attention, processing speed, and working memory improve substantially. (2) Methods: Two case studies are presented using MEG source imaging on an adult dyslexic, and a healthy older adult observed before and after training on movement discrimination two times/week for 8 weeks for adult dyslexic. (3) Results: We found improvements in reading, attention, processing speed, and working memory on neuropsychological tests. Substantial MEG signal increases in visual Motion Networks (V1, V3, MT, MST), Attention Networks (ACC, dlPFC, vlPFC and precuneous/ PCC areas) and Memory Networks (dlPFC). (4) Conclusions: Improving neural timing deficits before cognitive exercises to improve specific cognitive skills provides a rapid and effective method to improve cognitive skills. Improving the timing and sensitivity of low-level dorsal pathways, improving feedforward and feedback pathways, is essential to improve high-level cognitive skills. This adaptive training with substantial feedback shows cognitive transfer to tasks not trained on, significantly improving a person’s quality of life rapidly and effectively.

This paper aims to address the exponential stability and stabilization problems for a class of delayed nonlinear Markov jump systems under randomly occurring Denial-of-Service (DoS) attack and packet loss. Firstly, the stochastic characteristics of DoS attack and packet loss are depicted by the attack success rate and packet loss rate. Secondly, a Period Observation Window (POW) method and a hybrid-input strategy are proposed to compensate for the impact of DoS attack and packet loss on the system. Thirdly, A Dynamic Event-triggered Mechanism (DETM) is introduced to save more network resources and ensure the security and reliability of systems. Then, by constructing a general common Lyapunov functional and combining with the DETM and other inequality analysis techniques, the less conservative stability and stabilization criteria for the underlying systems are derived. In the end, the effectiveness of our result is verified through a numerical example.

Suitable soil structure and nutrient security are important for plant growth and development, characteristics of soil fractal dimension and distribution of physical and chemical properties and their interactions play an important role in studying the stability of soil structure and water and fertilizer cycles. As a sustainable management model, intercropping has positive benefits for erosion control, spatial optimization of resources, as well as improving system productivity. The effects of four intercropping methods on soil fractal dimension and physicochemical properties were investigated by intercropping Salvia miltiorrhiza with forage and S. miltiorrhiza with forest under typical karst rock desertification habitats in Guizhou. The results showed that soil nutrient content of intercropping was significantly higher than that of monoculture, the organic carbon content of soil grown under forest is higher than other treatments, and there was a non-significant change in soil water content of intercropping compared with monoculture. The soil fine-grained matter of intercropping was significantly higher than that of monoculture, while the soil fractal dimension showed a tendency to become larger with the increase of fine-grained matter. The intercropping planting, due to its component types and spatial and temporal configurations, leads to differences in soil water and fertilizer interactions, which can be combined with other ecological restoration measures to optimize the composite model and jointly promote the restoration and development of ecologically fragile areas.

Brain-stimulation reward, also known as intracranial self-stimulation (ICSS), is a commonly used procedure for studying brain reward function and drug reward. In electrical ICSS, an electrode is surgically implanted into the medial forebrain bundle in the lateral hypothalamus or the ventral tegmental area in the midbrain. Operant lever responding leads to the delivery of electrical pulse stimulation. The alteration in the stimulation frequency-lever response curve is used to evaluate the impact of pharmacological agents on brain reward function. If a test drug induces a leftward or upward shift in the ICSS response curve, it implies a reward-enhancing or abuse-like effect. Conversely, if a drug causes a rightward or downward shift in the functional response curve, it suggests a reward-attenuating or aversive effect. A significant drawback of electrical ICSS is the lack of cellular selectivity in understanding the neural substrates underlying drug reward versus aversion. Excitingly, recent advancements in optical ICSS (oICSS) have facilitated the development of at least three cell type-specific oICSS models – dopamine-, glutamate-, and GABA-dependent oICSS. In these new models, a comparable frequency-rate response curve has been established and employed to study the substrate-specific mechanisms underlying brain reward function and a drug's rewarding versus aversive effects. In this review article, we summarize recent progress in this exciting research area. The findings in these new behavioral models have not only increased our understanding of the neural mechanisms underlying drug reward and addiction but have also introduced a novel experimental approach in preclinical medication development for treating substance use disorders.

In the face of the current energy and environment problems, the full use of biomass resources instead of fossil energy to produce a series of high-value chemicals has great application prospects. 5-hydroxymethylfurfural (HMF), which can be synthesized from lignocellulose as raw material, is an important biological platform molecule. Its preparation and catalytic oxidation of subsequent products have important research significance and practical value. In the actual production process, porous organic polymer (POPs) catalysts are highly suitable for biomass catalytic conversion due to its high efficiency, low cost, good designability, and environmentally friendly features. Here, we briefly described the application of various types of POPs (including COFs、PAFs、HCPs、CMPs) in the preparation and catalytic conversion of HMF from lignocellulosic biomass, and analyzed the influence of the structural properties of catalysts for the catalytic performance. Finally, we summarized some challenges that POPs catalysts will face in biomass catalytic conversion, and prospected the important research directions in future. This review would provide valuable references for the efficient conversion of biomass resources into high-value chemicals in practical applications.

Magnetic Nanoparticles (MNPs) is a promising technique to cure brain diseases. On the one hand, by serving as drug carriers, they can bypass the blood-brain barrier and deliver drug molecules to the brain parenchyma; on the other hand, their transport trajectory can be manipulated by applying an external magnetic field. However, due to the complex microstructure of brain tissues, e.g. the anisotropy of white matter (WM), how to achieve desired drug distribution patterns, e.g. uniform distribution, by tuning the drug delivery system is largely unknown. Here, in this study, by adopting a mathematical model capable of capturing the diffusion trajectories of MNPs in the microstructures, we systematically investigated the effects of key parameters in the MNPs delivery system on the equivalent diffusion coefficient of MNPs in the microenvironment of brain WM. The results show that uniform distribution of MNPs in anisotropic tissues can be achieved by adjusting the particle size and magnetic field. We have not only obtained a deeper understanding on how to optimise the MNPs delivery system, it can also be anticipated that an improved mathematical model could even help to achieve complex drug distribution patterns in the complicated brain environment by designing an appropriate combination of the key parameters.

The volatile fatty acids (VFAs) productions, as well as particulate organics decomposition, soluble chemical oxygen demand (SCOD) yield, and the VFAs production pathways, of mesophilic and thermophilic anaerobic fermentation were investigated. Batch experiments showed that the decomposition rate of volatile suspended solids (VSS), particulate carbohydrate (P-C) and particulate protein (P-P) followed the first-order kinetic model at different temperature. However, the intermediates， accumulated in the process of protein or carbohydrate digestion had a more significant inhibitory effect on the production of VFAs during the mesophilic anaerobic acidification process. Thermophilic fermentation led to more accumulation of VFAs compared to mesophilic fermentation. Then 13C stable isotope labeling experiment demonstrated that, acetic (HAc), propionic (HPr) and butyric (HBu) could be produced from carbohydrate and protein digestion, but valeric (HVa) was only generated from the degradation of protein. Finally, the possible pathway of HVa synthesis was proposed.

Human pose estimation is a complex detection task in which the network needs to capture the rich information contained in the images. In this paper, we propose MSTPose (Multi-Scale Transformer for human Pose estimation). Specifically, MSTPose leverages a high-resolution Convolution neural network (CNN) to extract texture information from images. For the feature maps from three different scales produced by the backbone network, each branch performs the coordinate attention operations. The feature maps are then spatially and channel-wise flattened, combined with keypoint tokens generated through random initialization, and fed into a parallel Transformer structure to learn spatial dependencies between features. As the Transformer outputs one-dimensional sequential features, the mainstream two-dimensional heatmap method is abandoned in favor of one-dimensional coordinate vector regression. The experiments show that MSTPose outperforms other CNN-based pose estimation models and demonstrates clear advantages over CNN + Transformer networks of similar types.

Background: Endotheliopathy is common pathologic findings in patients with acute and long COVID-19. It may be associated with disease severity and predispose to long-term complications. Plasma levels of a proteoglycan syndecan-1 are found to be significantly elevated in patients with COVID-19, but its roles in assessing the disease severity and predicting long-term outcome are not fully understood. Methods: 124 consecutive hospitalized patients with SARS-CoV2 infection were prospectively enrolled and blood samples were collected on admission (T1), 3-4 days following treatment (T2), and 1-2 days prior to discharge or death (T3). Plasma levels of syndecan-1 were determined using an immunosorbent assay; various statistical analyses were performed to determine the association between plasma syndecan-1 levels and disease severity or the 60-day mortality rate. Results: Compared with those in the healthy controls, plasma levels of syndecan-1 in patients with critical COVID-19 were significantly higher (p<0.0001). However, there was no statistically significant difference among patients with different disease severity (p>0.05), resulting from large individual variability. Longitudinal analysis demonstrated that while the levels fluctuated during hospitalization in all patients, plasma syndecan-1 levels were persistently elevated from baseline in critical COVID19 patients. Cox proportional hazard regression analyses revealed that elevated plasma levels of syndecan-1 (>260 ng/mL at T1, >1018 ng/mL at T2, and >461 ng/mL at T3) were significantly associated with the 60-day mortality rate. Conclusions: Endotheliopathy, marked by glycocalyx degradation and elevated plasma syndecan-1, occurs in nearly all hospitalized patients with SARS-CoV2 infection; the elevated plasma syndecan-1 is associated with increased mortality in COVID-19 patients.

Abstract: Characterization the 3-D structure of clouds is needed for a more complete understanding of the Earth's radiative and latent heat fluxes. Here we develop and explore a “ray casting” algorithm applied to the Multi-angle Imaging SpectroRadiometer (MISR) on board the Terra satellite, to reconstruct 3-D cloud volumes for observed clouds. The ray casting algorithm is first applied to geometrically simple synthetic clouds to show that, under the assumption of perfect, clear-conservative cloud masks, the reconstruction method yields overestimation whose magnitude depends on the cloud geometry and the resolution of the reconstruction grid relative to the image pixel resolution. The method is then applied to two select MISR scenes, fully accounting for MISR’s viewing geometry for reconstructions over the Earth’s ellipsoidal surface. The MISR Radiometric Camera-by-camera Cloud Masks at 1.1 km resolution and custom cloud masks at 275 m resolution independently derived from MISR RGB channels are used as input cloud masks. A wind correction method, termed “cloud spreading”, is devised and applied to the cloud masks to offset potential cloud movements over short time intervals (around 7 minutes at maximum) between the cameras. The MISR cloud top height product is used as a constraint to reduce the overestimation at the cloud top. The reconstruction results show that their uncertainty is significant when the wind correction is applied, and that they have more refined structures when the input cloud mask has a higher resolution. Recommendations for improving the presented cloud volume reconstructions as well as for future passive remote sensing satellite missions are discussed.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

Purpose: Pancreatic cancer (PAAD) is one of the most lethal malignancies. Immunotherapy is largely ineffective in PAAD. T-cell exhaustion contributes to the resistance for immunotherapies. We investigated the prognostic potential of T cell exhaustion-related genes (TEXGs). Methods: Single-cell RNA (scRNA) sequencing dataset from TISCH, and bulk sequencing datasets from TCGA and GTEx were applied to screen differently expressed TEXGs. Kaplan-Meier survival, LASSO regression, and Univariate/Multivariate Cox regression analysis were performed to construct TEXGs risk model. This model was used to predict the prognosis, tumor immune microenvironment, and immunotherapy response. PAAD cohorts from ICGC and GSE71729 datasets were used to validate this risk model. Pan-cancer expression of SPOCK2 was performed in TISCH database. Results: A six-gene (SPOCK2, MT1X, LIPH, RARRES3, EMP1, and MEG3) risk model was constructed. Low-risk PAAD patients had longer survival time in both training dataset (TCGA-PAAD, n=178) and validation datasets (ICGC-PACA-CA, ICGC-PAAD-US, and GSE71729, n=412). Multivariate Cox regression analysis demonstrated that the risk score was an independent prognostic variable for PAAD. High-risk patients correlated with cancer-related KEGG pathway enrichment, higher mutation frequency of KRAS and TP53 genes, and immunosuppressive status. Immunohistochemistry staining confirmed the changes of TEXGs in clinical samples. Moreover, pan-cancer scRNA sequencing datasets from TISCH analysis indicated that SPOCK2 might be a novel marker of exhausted CD8+ T cells. Conclusion: In conclusion, we established and validated a T cell exhaustion-related prognostic signature for PAAD patients. Moreover, our study suggests that SPOCK2 may be a novel marker of exhausted CD8+ T cells.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

In a complex working environment, the fault signal of the gearbox is greatly affected by the outside world, and fault feature recognition is difficult, so the fault diagnosis accuracy is difficult to meet the expected requirements. To solve this problem, this paper proposes a gearbox fault diagnosis method based on an optimized stacked denoising auto encoder (SDAE) and kernel extreme learning machine (KELM). Firstly, the Particle Swarm Optimization algorithm in Adaptive Weight (SAPSO) was adopted to optimize the SDAE network structure, and the number of hidden layer nodes, learning rate, noise addition ratio and iteration times were adaptively obtained to make SDAE obtain the best network structure. Then, the best SDAE network structure was used to extract the deep feature information of weak faults in the original signal. Finally, the extracted fault features are fed into KELM for fault classification. Experimental results show that, compared with existing commonly used methods of fault diagnosis, the fault diagnosis model proposed in this paper can reduce the influence of noise in the original signal can better learn the deep-level features in the original signal and has higher diagnosis accuracy, faster diagnosis speed and good generalization in fault diagnosis.

Technological advances in tea production are critical to meet global demands for tea consumption. To illuminate differences in the scientific and commercial relevance of research programs between major tea-related research organizations around the world, we conducted a bibliometric analysis comparing the scientific outputs, including peer-reviewed publications and patents, of six major research organizations published between January 01, 2008 and July 11, 2020. For this competitive ranking analysis, we examined a number of papers, research topics, academic influence, capacity for development, capacity for collaboration, and capacity for technological innovation. Among the six research organizations, Anhui Agricultural University (in China) had the most publications, while the Chinese Academy of Agricultural Sciences, Tea Research Institute showed a higher capacity for development. The Council for Scientific and Industrial Research (in India) and the University of Shizuoka (Japan) both showed high academic influence, while the University of Shizuoka, Tea Research Association Tocklai and National Agriculture and Food Research Organization (Japan) showed a high capacity for collaboration. The Chinese Academy of Agricultural Sciences, Tea Research Institute applied for the most patents, while the Council for Scientific and Industrial Research applied for the most international patents.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

In this work, we studies the principle of ground electrode current field through ground communication technology, signal design, and optimal working mode of excitation source, so as to adapt the working mode, working frequency, and transmission medium condition of signal transmission. Through waveform design, energy is concentrated in the main conduction direction, which is beneficial for signal filtering at the receiving end and achieving high reliability data transmission; On this basis, on-site environmental testing was conducted to verify the detection and recognition technology of weak signals. Signal design and detection recognition are a very important part of the grounding electrode current field through ground communication technology. The grounding electrode current field through ground communication technology is mainly applied to solve the problem of communication between rescue personnel and trapped personnel before and during tunnel engineering collapse and rescue.

This paper presents a novel approach for semantic segmentation of building roof in dense urban environment with Deep Convolution Neural Network (DCNN) using imagery acquired by a Chinese Very High Resolution (VHR) satellite mission, i.e. GaoFen-2 (GF-2). To provide an operational end-to-end work flow for accurate build roof mapping with feature extraction as well as image segmentation, a fully convolutional DCNN with both convolutional and deconvolutional layers is designed to perform the VHR image analysis for labeling pixels. Since the diverse urban patterns and building styles in large areas, sample image data sets of building roof and non-building roof are collected over different metropolitan regions in China. We selected typical cities with dense urban environment in each metropolitan region as study areas for collecting training and test samples. High performance cluster with GPU-mounted workstations is employed to perform the model training and optimization. With the building roof samples collected over different cities, the predictive model with multiple NN layers is developed for building roof labeling. The validation of the building roof map shows that the overall accuracy(OA) and the mean Intersection Over Union( mIOU) of DCNN based segmentation are 94.67%, 0.85 respectively, while CRF-refined segmentation achieved OA of 94.69% and mIOU of 0.83. The results suggest that the proposed approach is a promising solution for building roof mapping with VHR images over large areas across different urban and building patterns. With the operational acquisition of GF2 VHR imagery, it is expected to develop an automated pipeline for operational built-up area monitoring and timely update of building roof map over large areas.

Pathogens, especially invasive species, have caused significant global ecological, economic, and social losses in forests. Plant disease research has traditionally focused on direct interactions between plants and pathogens in an appropriate environment. However, recent research indicates that the microbiome can interact with the plant host and pathogens to modulate plant resistance or pathogen pathogenicity, thereby altering the outcome of plant–pathogen interactions. Thus, this presents new opportunities for studying the microbial management of forest diseases. Compared to parallel studies on human and crop microbiomes, research into the forest tree microbiome and its critical role in forest disease progression has lagged. The rapid development of microbiome sequencing and analysis technologies has resulted in the rapid accumulation of a large body of evidence regarding the association between forest microbiomes and diseases. These data will aid the development of innovative, effective, and environmentally sustainable methods for the microbial management of forest diseases. Herein, we summarize the most recent findings on the dynamic structure and composition of forest tree microbiomes in belowground and aboveground plant tissues (i.e., rhizosphere, endosphere, and phyllosphere), as well as their pleiotropic impact on plant immunity and pathogen pathogenicity, highlighting representative examples of biological control agents used to modulate relevant tree microbiomes. Lastly, we discuss the potential application of forest tree microbiomes in disease control as well as their future prospects and challenges.

Target recognition mainly includes three approaches: optical image-based, echo detection-based, and passive signal analysis-based methods. Among them, the passive signal-based method is closely integrated with practical applications due to its strong environmental adaptability. Based on passive radar signal analysis, we design an "end-to-end" model that cascades a noise estimation network with a recognition network to identify working modes in noise environment. The noise estimation network is implemented based on U-Net, which adopts a method of feature extraction and reconstruction to adaptively estimate the noise mapping level of the sample, which can help the recognition network to reduce noise interference. Focusing on the characteristics of radar signal, the recognition network is realized based on Multi-Scale Convolutional Attention Network (MSCANet). Firstly, the deep group convolution is used to isolate the channel interaction in the shallow network. Then, through the multi-scale convolution module, finer-grained features of the signal are extracted without increasing the complexity of the model. Finally, the self-attention mechanism is used to suppress the influence of low-correlation and negative-correlation channels and spaces. This method overcomes the problem that the conventional method is seriously disturbed by noise. We validated the proposed method in 81 kinds of noise environments, achieving an average accuracy of 94.65%. Additionally, we discussed the performance of six machine learning algorithms and four deep learning algorithms. Compared to these methods, proposed MSCANet achieved an accuracy improvement of approximately 17%. Our method demonstrates better generalization and robustness.

The portal website of a university or a college usually represents the cultural characteristics and teaching advantages and plays a vital role in higher education, showing the style of the university or college to society and improving the admission rate. Mississippi State (MS) is bounded by the Mississippi River in the west and the Gulf of Mexico in the south, with a population of 3.1 million. It has a rich cultural heritage, and many universities, especially historically black colleges and universities (HBCUS), have strong scientific research strength in agriculture, medicine, petrochemicals and papermaking. Therefore, this article will analyze the design of the portal websites of four HBCUs in Mississippi from two aspects: user experience (UE) and functional architecture (FA), determine their advantages, disadvantages, similarities and differences, and propose some optimization suggestions.

Large language model (LLM) is a representation of a major advancement in AI, and has been used in multiple natural language processing tasks. Nevertheless, in different business scenarios, LLM requires fine-tuning by engineers to achieve satisfactory performance, and the cost of achieving target performance and fine-tuning may not match. Based on the Baidu STI dataset, we study the upper bound of the performance that classical information retrieval methods can achieve under a specific business, and compare it with the cost and performance of the participating team based on LLM. This paper gives an insight into the potential of classical computational linguistics algorithms, and which can help decision-makers make reasonable choices for LLM and low-cost methods in business R&D.

While the language model using the stop sign as an independent token has been widely used to decide when the model should stop, it may lead to the growth of vocabulary dimensions and further problems. Similarly, present research on game algorithms usually estimate stopping point related problems based on the evaluation of the winning rate. However, information redundancy may also exist in such models, thus increasing the training difficulty. Above two types of tasks (and similar autoregressive tasks) show a common problem of stopping point prediction. In this paper, we describe a design of separated model, trying to separate the complexity of stopping point prediction from the main task model, so that the information used for estimating stopping point can be reduced. On this basis, in order to verify the rationality of using separated model, we propose a model-free test method. It judges the separability of transformed data based on point difference and sequence difference metrics. In this way, it can predict the credibility of the separated model inference.

Directed energy deposition (DED) is an efficient method to fabricate functionally graded materials (FGMs) with gradient composition and complex structures, allowing for local tailoring of properties instead of the costly need for extraneous welds and joints. In this study, a FGM from stainless steel to Inconel alloy was successfully fabricated using the powder-based laser DED. A very refined grain structure has been observed in at the composition with 75 wt.% Inconel alloy content, which also exhibits the highest (entropy). For the first time, the post heat treatments, microstructure and aging precipitation behaviors of FGMs were systematically studied via experimental characterization and computation, to elucidate their effects on the gradient smoothing and mechanical properties. The diffusion and segregation of Ni, Nb and Ti elements underly the transformation mechanism between Laves, δ, γ’ and γ’’ phases during precipitation. Homogenization on FGMs not only eliminates the heterogeneity inherited from the AM process, but also provides a practical way to smoothen the gradient on composition and microstructure for the eventual good gradient properties. It has a direct influence on the following precipitation behaviors in the FGM, which highly relies on the diffusion degree of the elements in the matrix and grain boundaries. The high-throughput thermodynamic modeling and kinetic modeling were exploited to evaluate the experimental microstructure and address computational uncertainty using different thermodynamic conditions and databases, which enables an accelerated design through local tailoring of process-structure-property relationships to develop new functional materials.

We previously showed that feeding mice a diet containing 1% mantle tissue decreased food consumption, leading to death. We also isolated and identified toxic substances in the mantle tissue. In the present study, we investigated the characteristics and stability of mantle tissue toxicity. Treatment of mantle tissue with 1 mM HCl, 1 mM NaOH, 1 mM dithiothreitol, and 1 mM H2O2 and heating did not reduce the toxicity of mantle tissue in mice. These results suggest that mantle toxins are stable in tissues, particularly when exposed to acidic and digestive enzymes. We examined whether mantle tissue exhibited acute toxicity. Diets containing 1% and 20% mantle extract showed similar levels of toxicity, demonstrating that feeding of mantle tissue does not lead to acute toxicity. Finally, we examined the toxicity of the mantle tissue against small intestinal tissue. Chronic feeding of mantle tissue to mice changed the color of the small intestine. Real-time PCR analysis showed that mantle tissue feeding caused changes of inflammation and endoplasmic reticulum stress markers in the small intestine. These results suggest that feeding of mantle tissue causes toxicity after causing initial damage to the small intestinal tissue.

In this work, cobalt doped ZnO nanorod arrays with anticorrosion function were successfully prepared on FTO substrate by a simple aqueous solution method. XRD and EDS results indicate the doped Co2+ has successfully incorporated into the ZnO crystal lattice. Photocurrent density and open circuit potential (OCP) results indicate the photocathodic protection performance for 316 stainless steel (316 SS) and Q235 carbon steel in 3.5 wt.% NaCl solution under 300 W Xe lamp enhanced with the increase of cobalt concentration, and the photoanode with 15% Co/Zn ratio has the optimal photocathodic protection effect. The mechanism of enhancement may be result from the narrowed band gap, the lower recombination rate of photogenerated electron-holes, the intermediate impurity level and the split of the hypo-outer shell of cobalt ions.

The minimum dominating tree (MDT) problem consists of finding a minimum weight sub-graph from an undirected graph, such that each vertex not in this sub-graph is adjacent to at least one of the vertices in it, and the sub-graph is connected without any ring structures. This paper presents a Dual Neighborhoods Search (DNS) algorithm for solving the MDT problem, which integrates several distinguishing features, such as two neighborhoods collaboratively working for optimizing the objective function, a fast neighborhood evaluation method to boost the searching effectiveness, and several diversification techniques to help the searching process jump out of the local optimum trap thus obtaining better solutions. DNS improves the previous best-known results for 4 public benchmark instances while providing competitive results for the remaining ones. Several ingredients of DNS are investigated to demonstrate the importance of the proposed ideas and techniques.

The influence of polysialic acid (PSA) and sialic acid (SA) on the gut microbial community composition and metabolites in healthy human was investigated using a bionic gastrointestinal reactor. The results indicated that PSA and SA significantly changed the gut microbiota and metabolites in different degrees. PSA can increase the relative abundances of Faecalibacterium and Allisonella, whereas SA can increase those of Bifidobacterium and Megamonas. Both can significantly increase the content of short-chain fatty acids. The results of metabolome analysis showed that PSA can upregulate ergosterol peroxide and gallic acid and downregulate the harmful metabolite N-acetylputrescine. SA can upregulate 4-pyridoxic acid and lipoic acid. PSA and SA affect gut microbiota and metabolites in different ways and have positive effects on human health. These results will provide reference for the further development of PSA- and SA-related functional foods and health products.

The sustainable development of resource-based cities has long been a focal point for both governmental policies and academic research. A wealth of academic literature identifies the 'resource curse' as a critical barrier to sustainable development in these urban areas. Despite extensive studies, a consensus on effective strategies to circumvent or resolve this challenge remains elusive. Recent empirical data reveals a noticeable pattern of economic growth differentiation in China's resource-based cities. Why do some resource-based cities experience economic decline while others achieve sustainable economic growth? Therefore, this paper analyzes the reasons for the divergence of economic growth in resource cities from the perspective of heterogeneity. The results of the study show that the phenomenon of the resource curse is conditional, and the heterogeneity of demo-graphic changes, geographic location and institutional environment has a significant impact on the economic growth of resource cities. These factors are investigated to elucidate the observed diversification and heterogeneity in the economic growth of resource-based cities. Building upon this analysis, the paper proposes a framework for differentiated sustainable development pathways tailored to the unique contexts of these cities. This approach not only contributes to the current understanding of the 'resource curse' but also offers novel insights for future research aiming to adopt a more nuanced and context-specific perspective in examining sustainable urban development.

Three-phase AC electric arc furnace (EAF) is a typical non-linear load, causing many power quality problems. Most of the researches on the voltage problems of EAF mainly focus on the voltage fluctuation, and less on the transient voltage problems caused by EAF short circuit and open circuit. In this paper, the relationship between voltage and current of EAF is obtained by combining hyperbolic function and exponential function, then the white noise and chaotic circuit are added to establish the EAF model which is suitable for the study of voltage fluctuation and transient voltage. This paper analyzes the causes of the transient voltage problem of the EAF, calculates the short-circuit current, reactive impact and the influence on voltage at the point of common coupling (PCC) in the three-phase short-circuit of the EAF, and compares the calculation results with the simulation results to prove the accuracy of this model. The results show that the reactive impact of three-phase short circuit is about twice as much as that of normal operation of EAF, resulting in about 30% voltage sag at the PCC, which is very unfavorable to the power grid. This paper provides reference for transient power quality evaluation and dynamic reactive power compensation of EAF.

Using the techniques of computer-aided drug design, the docking of Survivin and known active small molecules was simulated and then the key amino acid residue fragment of the target protein was analyzed. It led to the discovery of active groups capable of binding to the critical sites. Through the use of the natural product, Oleanolic Acid, as a lead compound, the introduction of the active groups onto the A-ring, and the modification of the carboxyl group at the C-28 position using esterification or amidation, twenty new Oleanolic acid derivatives had been designed and synthesized.A549 and SGC-7901 cells were used to screen the antitumor activity in vitro through the standard MTT method. The compounds, II₃, III₅ and Ⅳ_4, exhibited more potent cytotoxicity than positive drugs.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Dictionary Learning (DL) and Sparse Representation (SR) based Classifier have impacted greatly on the classification performance and has had good recognition rate on image data. In Video Semantic Analysis (VSA), the local structure of video data contains more vital discriminative information needed for classification. However, this has not been fully exploited by the current DL based approaches. Besides, similar coding findings are not being realized from video features with the same video category. Based on the issues stated afore, a novel learning algorithm, called Sparsity based Locality-Sensitive Discriminative Dictionary Learning(SLSDDL) for VSA is proposed in this paper. In the proposed algorithm, a discriminant loss function for the category based on sparse coding of the sparse coefficients is introduced into structure of Locality-Sensitive Dictionary Learning (LSDL) algorithm. Finally, the sparse coefficients for the testing video feature sample are solved by the optimized method of SLSDDL and the classification result for video semantic is obtained by minimizing the error between the original and reconstructed samples. The experiment results show that, the proposed SLSDDL significantly improves the performance of video semantic detection compared with the comparative state-of-the-art approaches. Moreover, the robustness to various diverse environments in video is also demonstrated, which proves the universality of the novel approach.

Convolutional neural networks (CNNs) face challenges in capturing long-distance text correlations, and Bidirectional Long Short-Term Memory (BiLSTM) networks exhibit limited feature extraction capabilities for text classification of work order. To address the abovementioned problems, this work utilizes an ensemble learning approach to integrate model elements efficiently. This study presents a method for classifying work order texts using a hybrid neural network model called BERT-BiLSTM-CNN. First, use Bert for preprocessing to obtain text vector representations. Then, capture context and process sequence information through BiLSTM. Next, capture local features in the text through CNN. Finally, obtain classification results through Softmax. Through comparative analysis, the method of fusing these three models is superior to other hybrid neural network model architectures in multiple classification tasks. It has a significant effect on work order classification.

Though Cyber Physical Systems (CPS) become very popular in last the decade, dependability of CPS is still a critical issue and related survey is rare. We try to spell out the jigsaw of technologies and figure out the technical trends of dependable self-managing CPS. This survey first recalls the motivation and the similar concepts. By analyzing four generic architectures, we summarize the common characteristics and related assurance technologies, and propose a more generic environment-in-loop processing flow of CPS and a formal interaction flow between physical space and cyber space. Further, the similarity between correctness and dependability is formally analyzed and the new five research questions of dependable self-managing CPS are presented. Then we review the critical technologies and related correctness verification & validation (V&V) methods, the architectures for dependable self-managing CPS. Further, the detail dependability management and V&V technologies are surveyed, which covers the areas of running-time fault management methods and whole life cycle V&V technologies, maintenance and available tool sets. For holistic CPS development, Modeling techniques and MDE (model driven engineering) based V&V methods are analyzed in detail. Then we complete the jigsaw of technologies and figure out the missing part. Further, we propose the technical challenges and the further direction. To our best knowledge, this is the first comprehensive survey on dependable self-managing CPS development and evaluation.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

Visualization of the seabed terrain is one of the key functions of marine geographic information system. The major challenge here is that the obtained data for seabed terrain usually consists of elevation and sediment only but does not include remote sensing images, which is important for ground terrain visualization, as they can be used as textures to reveal detailed information and achieve realistic visual results. Existing seabed terrain visualizing methods (including annotations, color-mapping, and texture-mapping) have limitations in reality and intuition, as they are inadequate to express the physical characteristics of sediment accurately. This paper presents a novel and advanced 3D visualization method of seabed terrain, which introduces the Physically Based Rendering (PBR) theory into the field of geographic visualization. We analyze the main categories of seabed sediments and their optical features respectively, then develop a procedural method to generate physically based rendering materials for different sediments. Then an enhanced bidirectional reflectance distribution function is employed to achieve accurate and intuitive terrain rendering. We also refine the texture sampling method and propose a procedural seabed objects generation method to construct a more natural and realistic undersea environment. Experimental results reveal our method can make good use of the limited seabed terrain data and get significant improvements in visual effect, which can help users to cognize and analyze the seabed geographic environment more accurately and intuitively.

Surface finishing is challenging for additively manufactured components with complex geometries. Magnetic abrasive finishing (MAF) is a promising surface finishing technology that can refine the surface quality of components with complex shapes produced by additive manufacturing. However, there is insufficient study regarding the impact of MAF on microstructure-property relationships for additively manufactured builds, which is critical for evaluating the mechanical performance. Furthermore, although MAF is usually used as the final step of post-processing, it remains unclear whether adjusting the sequence between MAF and other processes, e.g., heat treatment, can potentially improve the mechanical performance. In this work, the effects of MAF on the microstructure and mechanical property evolution of Inconel 718 superalloys made by laser powder bed fusion (LPBF) were studied. The application of MAF was found to significantly reduce the surface roughness of alloys and refine the grain size of aged samples. Moreover, MAF is able to increase the elongation of materials, which can be further influenced by the sequence of MAF and different heat treatments. The highest elongation can be achieved when MAF is performed between homogenization and aging processes. This work demonstrated a promising solution to improving the performance of LPBF Inconel 718 by combining MAF and heat treatment, which provides new perspectives on the post-processing development of additively manufactured alloys for advanced mechanical properties.

A comprehensive review on symmetry and conditional symmetry is made from the core conception of symmetry and conditional symmetry. For a dynamical system, the structure of symmetry means its robustness against the polarity change of some of the system variables. Symmetric systems typically show symmetrical dynamics and even when the symmetry is broken, symmetric pairs of coexisting attractors are born annotating the symmetry in another way. The polarity balance can be recovered by the combinations of the polarity reverse of system variables, and furthermore, it can also be restored by the offset boosting of some of the system variables if the variables lead to the polarity reverse from their functions. In this case, conditional symmetry is constructed giving a chance for a dynamical system outputting coexisting attractors. Symmetric strange attractors typically represent the flexible polarity reverse of some of the system variables, which brings more alternatives of chaotic signal and more convenience for chaos application. Symmetric and conditionally symmetric coexisting attractors can also be found in memristive systems and circuits. Therefore, symmetric chaotic system and those of conditional symmetry provide sufficient system options for chao-based applications.

The development of photocatalysts with a wide spectral response and effective carrier separation capability is essential for the green degradation of tetracycline. In this work, a magnetic recyclable Z-scheme ZnO/ZnFe2O4 heterojunction (ZZF) was successfully constructed by the solid phase method using MIL-88A(Fe)@Zn as the precursor. Appropriate band gap width and Z-scheme charge transfer mechanism make ZZF have excellent visible light absorption performance, efficient charge separation and strong redox ability. Under visible light irradiation, the degradation efficiency of TCH for optimal sample ZZF2 can reach 86.3 % within 75 min in deionized water, and achieve 92.9 % within 60 min in tap water, which exhibits superior stability and reusability after five cycles. Moreover, the catalyst in the water can be conveniently recovered by magnetic force. After visible light irradiation for 70 minutes, the temperature of the reaction system increased by 21.9 °C. Its degradation constant (35.53×10-3 min-1) increases 5.1 times that at room temperature (6.95×10-3 min-1). Thermal energy perfects the kinetic driving force of the reactants and promotes carrier migration to produce more •O2- and •OH. This work provides a potential candidate and inspires the design of photocatalyst for tetracycline hydrochloride degradation.

Different kinds of freshwater fish soups show a diverse range of health functions, due to their different nutritional substances and corresponding bioactivities. Crucian carp soup and snakehead soup have different dietotherapy functions, crucian carp soup is suitable for lactating women and snakehead soup is suitable for postoperative patients. In the current study, the changes of nutrient profiles in the different fish soups, such as chemical composition, free amino acids, mineral and fatty acid contents, were investigated. The antioxidant activities of the fish soups were evaluated by using the DPPH radical scavenging activity, the ferrous ion chelating activity, the hydroxyl radical-scavenging activity and the reducing power effect. In order to learn the theoretical basis of the potential role fish soup plays in diet therapy functions after being digested by the human body, the nutrient profiling and bioactivities of the fish soup samples after simulated gastrointestinal digestion were also explored. The intensive profiles of nutritional composition and antioxidant activities of these two kinds of fish soups were expected to partly provide the theoretical basis of therapeutic effects.

Abstract: Dispersal strategies of a species can affect its invasion success. Investigation into the dispersal strategies of invasive species in relation to different factors helps our understanding of the invasion mechanisms and provides knowledge for population management and invasion evaluation. Tetranychus ludeni Zacher (Acari: Tetranychidae) is an invasive species, which is native to Europe but now cosmopolitan. Here, we examined the effects of age and density on dispersal in mated females. Our results show that older females with more eggs were more likely to disperse and moved longer distances than younger ones with fewer eggs. Older females spread most of their eggs out of the natal habitats and over longer distances, which reduced competition and increased offspring fitness. Females significantly increased dispersal probability and distance with the increase of population density to avoid crowding. The synchronization of dispersal and reproduction, along with the positive density-dependent dispersal strategy, may facilitate habitat colonization and invasion speed of T. ludeni.

This research investigates the fatigue crack propagation on the lower surface of rocket deflector troughs of offshore rocket launch platforms. Initially, a numerical model of the offshore rocket launch platform is established using ABAQUS based on the Extended Finite Element Method (XFEM). Subsequently, two variable parameters—namely, the initial crack length and initial tilt angle—are introduced. This research systematically analyzes the impact of these parameters on fatigue crack propagation patterns in both the maximum stress and maximum deformation regions of the deflector channels under the combined conditions of high temperature and impact. Finally, the research indicates that the propagation length of surface cracks in the deflector trough exhibits a trend of initial increase followed by a subsequent decrease with the increase in the preset inclination angle. Notably, the stable propagation rate of the crack in the region of maximum deformation surpasses that observed in the region of maximum stress. Through meticulous comparative analysis, it is evident that temperature loading significantly fosters the initiation and propagation of cracks, particularly in the upper region of the deflector channel's lower surface.

Basil, renowned for its aromatic properties, exhibits commendable drought tolerance and holds significant value both as an edible and medicinal plant. Recognizing the scarcity of studies addressing basil’s response to drought stress, we undertook a comprehensive analysis of the volatile metabolome and transcriptome of sweet basil across four distinct levels of drought stress. Our metabolic analysis meticulously identified 830 metabolites, with 215 differentially accumulated metabolites discerned. Notably, the primary constituents of sweet basil volatiles exhibited minimal alterations, while the differentially accumulated metabolites were predominantly lipids and terpenes. The transcriptome analysis unveiled 27,181 differentially expressed DEGs, with a predominant focus on metabolic pathways and biosynthesis of secondary metabolites. Integrating insights from both transcriptome and volatile metabolomic analyses highlighted the pivotal roles of Alpha-linolenic acid, flavonoid, and lignin metabolism in fortifying the resistance of sweet basil against drought stress. This holistic approach not only enriches our understanding of the molecular intricacies underpinning basil’s drought resistance but also furnishes valuable insights for the molecular breeding of basil varieties endowed with enhanced drought tolerance.

Gyroscopes are fascinating instruments with a history of about 200 years. When J.G.F. Bohnenberger presented his machine to his students in 1810 at the University of Tuebingen, Germany, nobody could have foreseen that this fascinating development would be used for complex orientation and positioning. At the University of Stuttgart, Germany, a collection of 160 exhibits is available and in transition for a sustainable future. Here, the systems are digitized in 2D, 2.5D and 3D and are made available for a world-wide community using OpenAccess platforms. The technologies being used are Computed Tomography, Computer Vision, Endoscopy and Photogrammetry. The workflows for combining voxel representations and colored point clouds are described, to create Digital Twins of the tangible assets. Advantages and disadvantages are discussed und work for near future is outlined in this new and challenging field of Tech Heritage digitization.

Kiwifruit is a perennial horticultural crop species with high nutritional and economic value. However, various pathogens stress brings a serious threat to kiwifruit. Pentatricopeptide repeat proteins (PPRs) are characterized by tandem repetitions of 35 amino acid motifs, and have been found to function in plant RNA editing. However, the roles of PPRs in plant development and disease resistance remain unclear. In this study, we performed a genome-wide identification and characterization of PPR gene family in two kiwifruit species (Actinidia chinensis (Ach), and Actinidia eriantha (Ace)) with markedly different disease resistance. A total of 497 and 499 PPRs were identified in Ach and Ace, respectively. All the kiwifruit PPRs could be phylogenetically divided into four subfamilies. There were about 40.68% PPRs predicted to be localized to mitochondria or chloroplasts. Synteny analysis showed that the expansion of kiwifruit PPRs mainly came from segmental duplication. Based on RNA-seq data from the fruit during 12 periods of development and maturity, weighted correlation network analysis suggested that two PPRs Actinidia20495.t1 and Actinidia15159.t1 were involved in the fruit development and maturation. In addition, we observed different gene expression of PPRs and chloroplast RNA editing profiles between resistant and susceptible kiwifruits after pathogen infection, indicating the roles of PPRs in stress response by modulating the editing extend of mRNA. The differentially expressed upstream transcription factors of PPRs were further identified, they may regulate resistance adaption by modulating the PPRs expression. These results provide a solid foundation for further analyses of the functions and molecular evolution of PPRs, in particular, for clarifying the resistance mechanisms in kiwifruits and breeding new cultivars with high resistance.

Background and Objectives: Although researchers suggested that non-pharmaceutical intervention (NPI) and vaccination together can provide the best protection from the COVID-19 [1], people’s willingness to adopt personal NPIs seems to decrease through the COVID-19 waves. This study seeks for an explanation for this observation based on the framework of risk perception. Materials and Methods: Two cross-sectional surveys (N = 407 in Survey 1 and N = 505 in Survey 2) were administered before and in the first outbreak of COVID-19 in Taiwan. The survey items were designed to measure people’s recognized severity of COVID-19, worry of COVID-19, intention to adopt personal NPIs, and attitude toward COVID-19 vaccines. We established a structural model according to the framework of risk perception, which was applied to fit the data of the two surveys. Results: The multigroup SEM (Structural Equation Modeling) results showed that worry (i.e., emotional component of risk perception) fully mediates the influence of recognized severity of COVID-19 (cognitive component of risk perception) on the intention to adopt NPIs in each survey. Before the outbreak (i.e., Survey 1), people’s attitude toward COVID-19 vaccines has nothing to do with their worry of COVID-19. However, when people have experienced the real outbreak of COVID-d19 (i.e., Survey 2), their attitude toward COVID-19 vaccines negatively predicts their worry of COVID-19, forming an indirectly negative effect on their intention to adopt personal NPIs, suggesting the occurrence of the Peltzman effect. That is, receiving vaccination makes people feel safer, that the other way around relaxes their alert for COVID-19, thus, declining the intention to adopt personal NPIs.

It has been proposed that tumourigenicity was an intrinsic feature of embryonic/germ cell developmental axis as well as embryonic/germ cell-related genes play a crucial role in tumourigenicity. Our previous studies indicated that primordial germ cell (PGC)-like potential could be reactivated in tumourigenesis. In this study, 4T1, 168FARN and 67NR cells which originated from the same mouse breast cancer were studied and the results indicated that the acquisition of embryonic/germ cell-like state is essential for tumourigenicity. We further demonstrated that somatic to PGC-like transformation (SPLT) was activated in 4T1 cells and that inhibition of PGC-like cell formation by depleting pluripotency and/or PGC specification-related genes markedly repressed SPLT and the tumourigenicity. Collectively, our findings reveal that tumourigenicity is linked to the acquisition of PGC-like state through SPLT in 4T1 cells, provide new insight into deeper understanding the biological nature of tumours and novel therapeutical strategies for cancer targeting.

Background: The present retrospective study was designed to evaluate the relative diagnostic utility of breast-specific gamma imaging (BSGI) and breast magnetic resonance imaging (MRI) as means of evaluating female breast cancer patients in China. Methods: A total of 229 malignant breast cancer patients underwent ultrasound, mammography, BSGI, and MRI between January 2015 and December 2018 for initial tumor staging. Of these patients, 73 were subsequently treated via definitive breast surgery following neoadjuvant chemotherapy (NAC), of whom 17 exhibited a complete pathologic response (pCR) to NAC. Results: BSGI and MRI were associated with respective 76.8% and 69.6% sensitivity values as a means of detecting residual tumors following NAC, while both of these approaches exhibited comparable specificity in this diagnostic context (58.8% vs 70.6%, P=0.473). Conclusion: These results demonstrate that BSGI is a useful auxiliary approach to evaluating pCR to NAC treatment.

Chemical composition analysis of açaí extracts revealed higher levels of total polyphenol content in purple açaí samples for both commercial (4.3 – 44.7 gallic acid equivalents mg/g) and non-commercial samples (30.2 – 42.0 mg/g) compared to white (8.2 – 11.9 mg/g) and oil samples (0.8 – 4.6 mg/g). The major anthocyanin compounds found in purple açaí samples were cyanidin-3-glucoside and cyanidin-3-rutinoside with total concentrations in the range of 3.6 – 14.3 cyanidin-3-glucoside equivalents mg/g. The oligomeric proanthocyanidins were quantified in the range of 1.5 – 6.1 procyanidin B1 equivalents mg/g. Moreover, açaí presented significant levels of calcium, magnesium, manganese, iron, zinc and copper, essential minor and trace elements, in comparison with other berries. All of the açaí extracts at 50 μg/mL potently inhibited the release of reactive oxygen species in lipopolysaccharide-stimulated RAW 264.7 macrophage cells, but none inhibited the release of nitric oxide. Furthermore, all the açaí samples demonstrated potential as wound healing agents due to the high levels of migration activity in human fibroblast cells.

Epigallocatechin gallate (EGCG), the principal catechin in green tea, exhibits diverse therapeutic properties. However, its clinical efficacy is hindered by poor stability and low bioavailability. This study investigated solid particle-in-oil-in-water (S/O/W) emulsions stabilized by whey protein isolate (WPI) and sodium caseinate (NaCas) as carriers to enhance the bioavailability and intestinal absorption of EGCG. Molecular docking revealed binding interactions between EGCG and these macromolecules. The emulsions exhibited high encapsulation efficiencies and augmented EGCG bioaccessibility by 64% compared to free EGCG in a simulated gastrointestinal digestion model. EGCG-loaded emulsions demonstrated minimal cytotoxicity towards Caco-2 cells and facilitated EGCG transport across the intestinal epithelial layer without compromising tight junction integrity. Notably, EGCG-loaded emulsions protected Caco-2 cells against oxidative stress by suppressing intracellular reactive oxygen species generation. The results demonstrate the potential of WPI- and NaCas-stabilized S/O/W emulsions to enhance the bioavailability, intestinal absorption, and bioactivity of EGCG, expanding its applications in functional foods and nutraceuticals.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

Nanling Mountain region is a typical southern hilly region, which plays an important ecological and environmental protection role in China's overall land protection pattern. Based on the remote sensing image data of Longnan City in Nanling Mountain in 2013, 2018 and 2023, this paper interpreted the land use type and analyzed the land use transfer situation by using Land use transfer flow, and Land use transfer matrix. At the same time, based on the remote sensing Ecological index (RSEI) model, the ecological environment quality of Longnan City from 2013 to 2023 was retrieved. The temporal and spatial response model of ecological environment quality to land use transfer in Longnan City from 2013 to 2023 was discussed based on Spatial autocorrelation and Geographic detector. The results show that from 2013 to 2023, the decrease of forest land (16.23km²) and the increase of construction land (13.25km²) were the main land use transfer in Longnan City. The ecological environment index of Longnan City in 2013, 2018 and 2023 was 0.789, 0.917 and 0.872, respectively, showing a trend of "first rising and then decreasing". The ecological environment quality in the north of Longnan City was significantly lower than that in the south, and the poor ecological quality area appeared in and around the northern main urban area, showing a trend of "inward contraction". Forest land, garden land, grassland, cultivated land and water area have a positive impact on ecological environment quality, while traffic land, construction land and other land have a negative impact on ecological environment quality. The response of ecological environment quality to different land use transfer modes is related to the change of the overall ecological environment quality. The interaction between LUCC and other factors had a great impact on the evolution of ecological environment quality in Longnan City.

A debris flows generation related to a poorly sorted mixture of soil, catchment topography and rainfall characteristic. Runoff of some depth on valley resulting from intensive rainfall can incur the sediments movement of beds or adjacent banks. The fluid flow in channel affected by rainfall parameters combinations, such as duration, intensity, cumulative rainfall, etc., is the key factor for debris movement. In this paper, the rainfall characteristics and occurrence conditions of debris flow in Xiongmao gully on July, 26th, 2016, have been explored, combined with field survey and indoor simulation experiment on the collected critical discharge parameters of debris movement. Further, debris distribution and the critical discharge characteristics have been analysed, by means of investigation on the catchment topography and occurrence cause of the debris flow, analysis of the critical discharge parameters on which the channel debris began to move, and K value clustering analysis method to characterize the rainfall pattern of the studied area, the discharge calculation of debris flow occurring in different rainfall patterns. The results have shown that, for the debris flow occurrence in Xiongmao gully, the debris initiation on the middle reaches of the gully provide the majority of solid particles for the disaster on July, 26th, 2016, and the upstream confluent provided catchment. Based on the relationship obtained from laboratory test, in which the calculated critical discharge was 43.8m3/s, less than the peak discharge (Qc =66.7m3/s), calculated by morphological method. In addition, it has been indicated that the dominated rainfall patterns of the studied area are first-quartile and second-quartile, that is, the rainfall is primarily at earlier or middle to preliminary stage of this time rainfall event. The critical discharge for the occurrence of debris flow on July, 26th was achieved 20a rainfall frequency, the larger runoff volume generated on shorten heavily rainfall. Based on individuality characteristics, such as distributed hydrological analysis, critical discharge and rainfall pattern of debris flow, the forewarning could be more efficient.

The calculation of the release of liquid hazardous chemicals storage tanks is an important part of the quantitative risk assessment of accidents. This paper mainly establishes a continuous real–time release model based on the instantaneous mass flow Q_m model. Meanwhile, the software function module was analyzed, and programming software was developed using C# language for model solving. A series of experiments for repeated leakage tests was designed and the discharges through three small holes with different heights for 200 s were observed. The results show that the continuous real–time leakage model is effective, and the deviation between theoretical and experimental release amounts are within a reasonable range. The higher the liquid level above the leak hole is, and the smaller the height of the leak hole from the ground is, the greater the flow rate at the leak orifice is and the smaller discharge rate change is. Therefore, the deviation between the theoretical release amount M_t and the experimental average release amount Ma is greater while the height of the leak hole from the ground is smaller, which indicates that the smaller the distance from the leak orifice to the ground, the greater the influence of the empirical discharge coefficient C₀ on the release amount M.

Lung cancer predominates in cancer-related deaths worldwide, with lung adenocarcinoma (LUAD) being a common histological subtype of lung cancer. The aim at this study was to search for biomarkers associated with the progression and prognosis of LUAD. We have integrated the expression profiles of 1174 lung cancer patients from five GEO datasets (GSE18842, GSE19804, GSE30219, GSE40791 and GSE68465) and identified a set of differentially expressed genes. Functional enrichment analysis showed that these genes are closely related to the progression of LUAD, such as cell cycle, mitosis and adhesion. Cytoscape software was used to establish a protein-protein interaction (PPI) network to analyze important modules using Molecular Complex Detection (MCODE), and finally CCNB1, BUB1B and TTK were selected for further study. The study found that compared with non-tumor lung tissue, CCNB1, BUB1B and TTK are highly expressed in LUAD. Kaplan-Meier analysis showed that CCNB1, BUB1B and TTK were negatively correlated with the overall survival and disease-free survival of patients. Gene set enrichment analysis (GSEA) demonstrated that for the samples of any hub gene highly expressed, most of the functional gene sets enriched in cell cycle. In summary, CCNB1, BUB1B and TTK can be used as biomarkers of poor prognosis of LUAD. The high expression of CCNB1, BUB1B and TTK can accelerate the progression of LUAD and lead to shorter survival, suggesting that they may be potential targets for treatment in LUAD.

Federated Distillation (FD) has recently attracted increasing attention for its efficiency in aggregating multiple diverse local models trained from statistically heterogeneous data of distributed clients. Existing FD methods generally treat these models equally by merely computing the average of their output soft predictions for some given input distillation sample, which does not take the diversity across all local models into account, thus leading to degraded performance of the aggregated model, especially when some local models learn little knowledge about the sample. In this paper, we propose a new perspective that treats the local data in each client as a specific domain and design a novel domain knowledge aware federated distillation method, dubbed DaFKD, that can discern the importance of each model to the distillation sample, and thus is able to optimize the ensemble of soft predictions from diverse models. Specifically, we employ a domain discriminator for each client, which is trained to identify the correlation factor between the sample and the corresponding domain. Then, to facilitate the training of the domain discriminator while saving communication costs, we propose sharing its partial parameters with the classification model. Extensive experiments on various datasets and settings show that the proposed method can improve the model accuracy by up to $6.02\%$ compared to state-of-the-art baselines.

Soups show diverse health functions, which should be related with their nutrient profiles. NMR spectroscopy is a robust, sensitive and rapid method to unveil or identify the chemical composition of food or food-derived metabolites. In the current study, 1H-NMR spectroscopy approach was applied to identify the metabolic profiling of two kinds of home-cooked freshwater fish soups (crucian carp and snakehead fish) before and after in vitro gastrointestinal digestion. The nutritional profiles of these two kinds of soups were identified at first. With the help of OPLS-DA method (Orthogonal Partial Least Squares Discriminant Analysis), these two different kinds freshwater fish under different states were completely discriminated. The metabolites changes in digested fish soups could reveal the information of chemical compounds which play important roles in the body. Furthermore, the metabolic patterns of different kinds of fish soups could reflect the various nutrition profiling characteristics for dietary therapy.

For equivalent modeling of mixed wind farms (WFs), existing clustering indicators cannot consider the complex coupling characteristics between different types of wind turbines (WTs). This paper proposes a refined equivalent modeling method for mixed WFs based on artificial intelligence technology. Firstly, the electromechanical transient performance of mixed WFs is analyzed. The WT type, wind speed and direction, and voltage dip are considered the main factors affecting the external dynamic response of mixed WFs. Secondly, the equivalent node model is established, including the selection of independent and dependent variables. Then, the multiple artificial neural networks (ANNs) are trained one by one based on sample data, to explore the nonlinear relationship between the dependent variables and the independent variables. Finally, the electromechanical transient simulations of the power systems with a mixed WF is carried out by using the MATLAB platform. Simulation results show that the proposed model can reflect the external characteristics of the mixed WF in different wind scenarios and voltage dips.