We show that combining vibrational spectroscopy with signal processing can result in a scheme for ultrasensitive detection of molecules. We consider the vibrational spectrum as a signal on the energy axis and apply a matched filter on that axis. On the example of a nerve agent molecule, we show that this allows detecting a molecule by its vibrational spectrum even when the recorded spectrum is completely buried in noise, when conventional spectroscopic detection is impossible. Detection is predicted to be possible with signal-to-noise ratios in recorded spectra as low as 0.1. We study the importance of spectral range used for detection as well as of the quality of the computed spectrum used to program the filter, specifically, the role of anharmonicity, of the exchange correlation functional, and of the basis set. The use of the full spectral range rather than of a narrow spectral window with key vibrations is shown to be advantageous, as well as accounting for anharmonicity.

A flexible asymmetric supercapacitor (ASCs) is successfully developed by using the composite of MoO3 and graphene oxide (GO) electrochemically deposited on carbon cloth (CC) (MoO3/rGO/CC) as the negative electrode, the MnO2 deposited on CC (MnO2/CC) as the positive electrode and Na2SO4/polyvinyl alcohol (PVA) as gel electrolyte. The results show that the introduction of GO layer can remarkably increase the specific capacitance of MoO3 from 282.7 F g-1 to 341.0 F g-1. Furthermore, the combination of such good electrode materials and a neutral gel electrolyte renders the fabrication of high-performance ASC with a large operating potential difference of 1.6 V in 0.5 mol L-1 Na2SO4 solution of water. Furthermore, the ASCs exhibit excellent cycle ability and the capacitance can maintain 87 % of its initial value after 6000 cycles. The fact that a light-emitting diode can be lighted up by the ASCs indicates the device’s potential applications as energy storage devices. The encouraging results demonstrate a promising application of the composite of MoO3 and GO in energy storage devices.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

The phenomenon of ordered self-assembly on solid substrates is a topic of interest in both fundamental surface science research and its applications in nanotechnology. The regulation and control of two-dimensional (2D) self-assembled supra-molecular structures on surfaces have been realized through applying external stimuli. By utilizing scanning tunneling microscopy (STM), researchers can investigate detailed phase transition process about self-assembled monolayers (SAMs), providing insight into the interplay between intermolecular weak interactions and substrate-molecule interactions, which govern the formation of molecular self-assembly. This review will discuss the structural transition of self-assembly probed by STM in response to external stimuli and provide state-of-art methods such as tip induced confinement for the alignment of SAM domains and selective chirality. Finally, we discuss the challenges and opportunities in the field of self-assembly and STM.

This research analyses extreme precipitation events in the Huaihe River Basin in China, a densely populated region with a history of human settlements and agricultural activities. This study aims to explore the impact of extreme precipitation index changes and provide decision-making suggestions for flood early warning and agricultural development in the Huaihe River Basin. The study utilises the NEX-GDDP-CMIP6 climate models dataset and the daily value dataset (V3.0) from China's national surface weather stations to investigate temporal and spatial changes in extreme precipitation indices from 1960 to 2014 and future projections. At the same time, this study adopted the RclimDex model, Taylor diagram and Sen+Mann-Kendall trend analysis research methods to analyse the data. The results reveal a slight increase in extreme precipitation indices from northwest to southeast within the basin, except for CDD, which shows a decreasing trend. Regarding spatial, the future increase of extreme precipitation in the Huaihe River Basin will show a spatial variation characteristic that decreases from northwest to southeast. These findings suggest that extreme precipitation events are intensifying in the region. Understanding these trends and their implications is vital for adaptation strategy planning and mitigating the risks associated with extreme precipitation events in the Huaihe River Basin.

We fabricated high-quality MAPbBr3 single crystals (SC) by introducing moderate amount electron-rich poly(propylene glycol bis(2-aminopropyl ether) (PEA) additives with an inverse temperature crystallization (ITC) method. The intramolecular vibrations and defective states of prepared MAPbBr3 single crystals were systemically studied by the in situ variable-temperature Fourier Transform Infrared (FTIR) Spectroscopy, X-ray photoelectron spectroscopy (XPS), and the synchrotron-based X-ray absorption near edge structure (XANES), et al. We infer that the proper amount of PEA additives would prevent the formation of intermediate states and crystal boundaries, passivating the density of defective states. The X-ray detection properties of single-crystal MAPbBr3 crystals were investigated, using both high dose and low dose X-ray photons at 40keV in synchrotron beamlines. The photocurrent of optimized PEA-treated MAPbBr3 single crystals demonstrate better performance compared with the as-prepared single crystals. Meanwhile, the decay time of MAPbBr3 single crystal is decreased from 460 ns to 210 ns by Time-resolved photoluminescence (TRPL) decay measurement, owing to the defect passivation by 0.5wt% PEA additives. The PEA-treated single crystals possess much faster decay time than the commercialized Ce:YAG scintillator (>500ns). These results help elucidate the passivation of defective states and contribute paths to manufacture high-quality single crystal perovskites for next-generation optoelectronic devices.

Postmenopausal osteoporosis, a metabolic bone disease associated with aging and that affects bones throughout the body, is emerging as an urgent public health concern and imposes a substantial healthcare burden on society. The clinical application of bisphosphonate, the primary treatment for osteoporosis, is limited owing to the drug’s severe complications. Herein, we investigate the synthesis and utilization of strontium-doped mesoporous bioactive glass loaded with alendronate (ALN@Sr-MBG) as a novel therapeutic agent for osteoporosis, to explore its potential as an alternative to alendronate (ALN). Strontium-doped mesoporous bioactive glass (Sr-MBG) was synthesized using the sol-gel method, while ALN@Sr-MBG was obtained by incorporating Sr-MBG into an alendronate saturated solution. The bioactivities of ALN@Sr-MBG, including biotoxicity, inflammation inhibition, and anti-osteoclast differentiation, were investigated in vitro using CCK-8, flow cytometry, tartrate-resistant acid phosphatase (TRAP) staining, and RT-PCR assays. Animal models were established by surgically removing the ovaries from non-pregnant female C57/BL mice, followed by weekly intraperitoneal injections of ALN@Sr-MBG, ALN, or excipients. After 8 weeks, the mice femurs were extracted and analyzed through Micro-CT scanning, and hematoxylin-eosi, osteoblastic, and osteogenic staining. The in vitro findings demonstrated that ALN@Sr-MBG displayed enhanced biological efficacy compared to ALN in terms of inflammation inhibition, osteogenesis promotion, and osteoclastogenesis inhibition. Furthermore, micro-CT analysis revealed that ALN@Sr-MBG significantly augmented bone mineral density (BMD), bone volume fraction (BV/TV), trabecular number (Tb.N), and trabecular thickness (Tb.Th), while reducing trabecular separation (Tb.Sp) and structural model index (SMI) in mice with ovariectomy-induced osteoporosis. The osteoblast and osteogenic staining results indicate the enhanced bioactivities of ALN@Sr-MBG in promoting bone formation and inhibiting bone resorption compared to ALN. In vitro and in vivo assessments further confirmed that ALN@Sr-MBG exhibits superior anti-osteoporotic bioactivity compared to ALN. The study findings confirm the potential of ALN@Sr-MBG as a novel alternative therapy to ALN and drug candidate for the treatment of osteoporosis.

Brucella abortus is a facultative intracellular Gram-negative bacterium that causes chronic persistent infections in humans and livestock. In this study, conventional bio-typing, multiple-locus variable-number tandem repeat analysis (MLVA), and whole-genome sequencing-single-nucleotide polymorphism (WGS-SNP) were used to investigate the molecular epidemiology characteristics of Brucella abortus strains in China and their relationships to world lineages. A total of 100 strains were collected from 1953 to 2013, suggesting that B. abortus circulated in China in the past five decades. Moreover, most strains were mainly distributed in the northwest area. During this period, seven biovars were found, indicating that B. abortus displayed a high diversity of biovars and that the main epidemic areas are in the northern provinces. Strains have high genetic diversity, and bruce07 is the most helpful locus for genotyping of this population. Moreover, 17 MLVA-11 genotypes were found; 13 of them are of known genotypes and four are unassigned genotypes, indicating that B. abortus in this study had several geographic origins. Still, strains from unassigned genotypes may originate from China. Many shared MLVA-16 genotypes were observed in strains from the same provinces in Northern China, which confirmed a brucellosis outbreak within northern regions. WGS-SNP analysis showed that eight Chinese strains formed a ladder-like phylogram (C. Ⅶ) with strains from nine countries, including Uganda, Iraq, Russia, Georgia, Spain, Italy, Egypt, Mongolia, and China; strains were introduced to these countries from a single source. Notably, Chinese strains were closely related to strains from Russia and Mongolia; frequent animal (cattle) trade and exchanges may promote this process. We will provide new and insightful information for strength surveillance and control of B. abortus brucellosis in China.

Red mud (RM), a bauxite residue, contains hazardous radioactive wastes and alkaline material and poses severe surface water and groundwater contamination risks, necessitating recycling. Pretreated RM can be used to make adsorbents for water treatment. However, its performance is affected by many factors, resulting in a nonlinear correlation and coupling relationship. This study aimed to identify the best formula for an RM adsorbent using a mathematical model that examines the relationship between 11 formulation types (e.g., pore-assisting agent, component modifier, and external binder) and nine properties (e.g., specific surface area, wetting angle, and Zeta potential, among others). This model was built using a back-propagation neural networks(BP) based on single-factor experimental data and orthogonal test data. The model trained and predicted the established network structure to obtain the optimal adsorbent formula. The RM particle adsorbents had a pH of 10.16, specific surface area(BET) of 48.92 m2·g−1, pore volume of 2.10 cm3·g−1, compressive strength(ST)) of 1.12 KPa, and 24-h immersion pulverization rate(η_m) of 3.72%. In the removal of total phosphorus in flotation tailings backwater, it exhibited a good adsorption capacity (Q)and total phosphorous removal rate(η) of 48.63 mg·g−1 and 95.13%, respectively.

Globally,coastal regions are vital areas of human activities and, as such, are centres of population growth and urban and economic development. Long-term human development has had a major impact on the ecological environment of coastal zones. Therefore, exploring the distribution and provenance of marine sediment types in coastal areas heavily influenced by human activities can provide scientific evidence and references for the current and future ecological management of these sensitive environments. For this reason, we have conducted an analysis on the sediment grain size, Endmember, organic matter content and geochemical elements in the Lu’erhuan River‒Malan Island‒Sandun Island area in the eastern part of Qinzhou Bay, a region heavily influenced by human activities. Sediment grain size clearly differs throughout the study site and the material provenances and hydrodynamic conditions are also varied, likely due to the local environmental conditions and the significant impact human activities have had on the area. The finest-grained sediment is imported from either inland or coastal areas via rivers and weak tidal currents, the next finest component is input from coastal areas through weak tidal currents, and the moderately coarse component mainly originates from nearby beaches. The two coarsest-grained sediment components are influenced by the combination of human activities, tidal currents and waves and enter the water via erosion. Organic matter provenance resembles that of the sediment components, exhibiting varied characteristics. This is due to the combination of natural and human activities in the bay. The organic matter in the upper reaches of the Lu’erhuan River originates from the river and coastal paddy fields, with obvious terrigenous characteristics; the organic matter in northern Malan Island mainly comes from external sources related to oyster farming; while organic matter in eastern Sandun Island is mainly produced endogenously by marine plankton. Al, Ti, Fe, Mg, K, Ga and other elements indicate that terrestrial sediments are significantly disturbed by human activities. However，Mn reflects the marine distribution of terrestrial sediments from the Lu’erhuan River to Jishuimen. Ca and Sr, indicators of marine sediments, are distributed in the eastern offshore area of Sandun Island, which is connected to the open waters. Due to the influence of human activities, As and Cd are highly enriched in the study area, while Cu is less affected by human activities.

Initial water content significantly affects the efficiency of soil stabilization. In this study, the effects of initial water content on the compressibility, strength, microstructure and composition of a lean clay soil stabilized by compound calcium-based stabilizer were investigated by static compaction test, unconfined compression test, optical microscope observations, environment scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction spectroscopy. The results indicate that as the initial water content increases in the range studied, both the compaction energy and the maximum compaction force decrease linearly and there are less soil aggregates or agglomerations, and smaller proportion of large pores in the compacted mixture structure. In addition, for specimens cured with or without external water supply and under different compaction degrees, the variation law of the unconfined compressive strength with initial water content is different and the highest strength value is obtained at various initial water contents. With the increase of initial water content, the percentage of oxygen element tends to increase in the reaction products of the calcium-based stabilizer, whereas the crystalline mineral of the soil did not change obviously.

The complete genomic sequence of a Cassava common mosaic virus Linggao isolate (CsCMV-LG) was determined from cassava (Manihot esculenta Crantz) with mild leafy mosaic symptom to no symptom in China. Excluding the poly(A) tail, the CsCMV-LG genome (GenBank accession No. MT038420) is 6374 nucleotides (nts) in length, with five major open reading frames encoding a 1450-amino acids (aa) RNA-dependent RNA polymerase (RdRp), three triple gene block (TGB) proteins (231-aa, 110-aa and 95-aa), and a 229-aa coat protein (CP). Phylogenetic analysis indicated that the complete genome of the CsCMV-LG is closely related to that of CsCMV-Brazilian which has been assigned to the genus Potexvirus, but the sequence identity shared only 88.0%. Notable, the mild CsCMV-LG isolate can also infect Nicotiana benthamiana in laboratory through rub inoculation causing mild vein yellowing at 15-day post inoculation. This is the first full-length genome sequence of a distinct isolate of Cassava common mosaic virus (CsCMV) infecting cassava in Hainan, China.

Avian infectious bronchitis virus (IBV) is the causative agent of infectious bronchitis, which causes considerable economic losses to the poultry industry worldwide. It is imperative to develop safe and efficient candidate vaccines to control IBV infection. In the current study, recombinant baculoviruses co-expressing S1 and N proteins, mono-expressing S1 or N proteins alone of IBV were constructed and prepared into subunit vaccines rHBM-S1-N, rHBM-S1 and rHBM-N. The levels of immune protection of these subunit vaccines were evaluated by inoculating specific pathogen-free (SPF) chickens at 14 days of age, boosting with the same dose 14 days later, and following challenge with a virulent GX-YL5 strain of IBV 14 days post-booster (dpb). The commercial vaccine strain H120 was used as a control. The IBV-specific antibody levels as well as the percentages of CD4+ and CD8+ T lymphocytes were detected within 28 days post-vaccination (dpv). The morbidity, mortality, and re-isolation of virus from the tracheas and kidneys of challenged birds were evaluated at 5 days post-challenge (dpc). The results showed that the IBV-specific antibody levels and the percentages of CD4+ and CD8+ T lymphocyte in rHBM-S1-N group were higher than those of rHBM-S1 and rHBM-N groups, especially the cellular immunity response. At 5 dpc, the mortality, morbidity and virus re-isolation rate of rHBM-S1-N were slightly higher than those of H120 group, but were lower than those of rHBM-S1 group and rHBM-N group. The present study demonstrated that the protection of recombinant baculovirus co-expressing S1 and N proteins was better than that of recombinant baculoviruses mono-expressing S1 or N protein alone. Thus, the recombinant baculovirus co-expressing S1 and N proteins could serve as a potential IBV vaccine and this demonstrates that the bivalent subunit vaccine including the S1 and N proteins might be a strategy for the development of an IBV subunit vaccine.

Microfluidics is facing critical challenges in the quest of miniaturizing, integrating, and automating in vitro diagnostics, including the increasing complexity of assays, the gap between the macroscale world and the microscale devices, and the diverse throughput demands in various clinical settings. Here a “3D extensible” microfluidic design paradigm that consists of a set of basic structures and unit operations was developed for constructing any application-specific assay. Four basic structures- check valve (in), check valve (out), double-check valve (in and out), and on-off valve, were designed to mimic basic acts in biochemical assays. By combining these structures linearly, a series of unit operations can be readily formed. We then proposed a “3D extensible” architecture to fulfill the needs of the function integration, the adaptive “world-to-chip” interface, and the adjustable throughput in the X, Y, and Z directions, respectively. To verify this design paradigm, we developed a fully integrated loop-mediated isothermal amplification microsystem that can directly accept swab samples and detect Chlamydia trachomatis automatically with a sensitivity one order higher than that of the conventional kit. This demonstration validated the feasibility of using this paradigm to develop integrated and automated microsystems in a less risky and more consistent manner.

Taking a certain type of test centrifuge as the research object, the finite element model of the test centrifuge is established, the vibration characteristics and aerodynamic performance of the test centrifuge are analyzed, and the structural optimization design of the test centrifuge is carried out. In this paper, the load is applied according to the actual working condition of a certain type of test centrifuge. The vibration of the mounting seat of the test centrifuge is analyzed and the structure of the mounting seat is optimized. After optimization, the vibration of the mounting seat is 77.38 % lower than that of the original mounting seat. Then, the aerodynamic analysis of the test centrifuge is carried out. The analysis results show that the test centrifuge moves more smoothly under the whole package shell and the steady flow shell, and the resistance decreases and the shaft load decreases. Finally, the steady flow shell of the test centrifuge is optimized. The analysis shows that the increase of the width of the steady flow shell can reduce the resistance coefficient, which is helpful to the stability of the test centrifuge during operation and reduces the unbalanced response of the system caused by air resistance.

The effects of reaction temperature, reaction time, heating rate, nitrogen flow rate and catalyst quality on the oil yield and oxygen content in the oil were investigated by using the single factor principle. Too high and too low reaction temperature, nitrogen flow rate, heating rate and reaction time have improved the yield of bio-oil, but the oxygen content in bio-oil is higher. The reduction of catalytic dose is beneficial to the increase of oil yield but not conducive to the increase of aromatic compound content. The optimal reaction conditions were observed as reaction temperature of 500℃, nitrogen flow rate of 110 mL/min, heating rate of 20℃/min, reaction time of 15min, mass ratio of catalyst to coconut coat powder was 1, and the oil yield was 4.97%, aquatic yield was 35.80%, and solid yield was 30.78%. The gas yield was 28.45%, the oxygen content was 10.3%, and the aromatic compound content was 89.7%.The analysis of catalytic cracking mechanism shows that most of the oxygen-containing compounds in the bio-oil are generated into water and aromatic compounds by catalytic cracking reaction at high temperature, thus removing oxygen.

Metabolites present in the hemolymph of honey bees play a crucial role in modulating the metamorphic process within the species. However, the precise alterations in metabolite composition, along with the associated variances and regulatory pathways implicated during the larvae-to-pupae metamorphosis of honey bees, remain incompletely elucidated. In this investigation, we gathered hemolymph samples from honey bee larvae at three distinct physiological stages-feeding, prepupal, and pupae and subjected them to metabolite analysis utilizing the liquid chromatography-mass spectrometry (LC-MS) technique. Employing principal component analysis (PCA) and partial least squares-discriminant analysis (PLS-DA), we identified significant differential metabolites and conducted a metabolic pathway analysis on those differentially up-regulated during the prepupal and pupae stages. Notably, metabolites up-regulated in the hemolymph of prepupal stage larvae primarily governed glucose metabolism and fat digestion and absorption, while those in pupae stage larvae were involved in regulating chitin and lipopolysaccharide precursor formation, as well as the biosynthesis of phenylalanine, tyrosine, and tryptophan. These findings bear significant implications for advancing our comprehension of the metamorphic processes in honey bees.

Infrared small target detection (ISTD) plays a crucial role in both civilian and military applications. The detection of small targets against dense cluttered backgrounds remains a challenging task, requiring the collaboration of false alarm source elimination and target detection. Existing approaches primarily focus on modeling targets while often neglecting false alarm sources. To address this limitation, we propose a Target and False Alarm Collaborative Detection Network to leverage the information provided by false alarm sources and the background. Firstly, we introduce a False Alarm Source Estimation Block (FEB) that estimates potential interferences present in the background by extracting features on multiple scales and employing stepwise upsampling for feature fusion. Subsequently, we propose a framework that employs multiple FEBs to eliminate false alarm sources across multiple scales. Finally, a Target Segmentation Block (TSB) is introduced to accurately segment the targets to produce the final detection result. Experiments on public datasets demonstrate that, compared to other methods, our model achieves high accuracy in segmenting targets while being able to extract false alarm sources which can be used for further studies.

The migration paths and distribution driving factors of heavy metals in dry and windy area polluted by their production in the North China need a further research. To address this research gap, we collected 675 soil samples, 72 atmospheric deposition samples and 20 water samples around a production area and measured its heavy metal concentrations. Results showed that the Cu, Zn, As and Pb in 0-10 cm soil layer showed a fan-shaped distribution, which was consistent with their atmospheric deposition fluxes. It indicated the distribution patterns of these heavy metals were driven by strong winds in studied area. Although Cr concentrated to the production area in the 0-10 cm soil layer, principal component analysis showed that this migration was through wind as well. The concentration of Cd in the river increased from 0.257 mg/L to 0.460 mg/L along water flowing, and caused the same distribution trend in soil near the river from upstream to downstream. Unlike the above, surface runoff should drive the Cd migration. The concentration of Pb in the river was over threshold of pollution, and also led to an accumulation in the 5-10 cm soil layer. It suggested that the migration of Pb was through both wind and surface runoff. Six studied heavy metals showed different migration behaviors, and specific control strategies for individual heavy metal should be concerned.

This study primarily investigates the effect of fly ash (FA) content on the mechanical properties and hydration performance of alkali-activated ground granulated blast furnace slag cements (AAGC), and compares the related properties with ordinary Portland cement (OPC). Additionally, the study examined the hydration products, thermal analysis, MIP, SEM, chemically bound water, and pH values of AAGC. The compressive strength of AAGC showed a retrogression phenomenon from 3 to 28 days, with the 14-day and 28-day compressive strengths of AAGC being higher than those of OPC. The AAGC with 20% FA content exhibits the highest 28-day compressive strength (75 MPa). The hydration heat release rate curved of OPC and AAGC can be divided into the initial induction period, induction period, acceleration period, deceleration period and steady period. As FA content increases, the 28-day pore volume of AAGC increased while pH values and chemically bound water decrease. SEM images of AAGC with low FA content showed more microcracks.

In order to study the crystallinity of different density polyethylenes, the experimental study on the transformation of the conductance mechanism under high electric field was carried out. The X-ray Diffraction(XRD), Different Scanning Calorimeter(DSC), Direct Current(DC) breakdown of Low-density polyethylene(LDPE), Linear low density polyethylene(LLDPE), Medium density polyethylene(MDPE) and High-density polyethylene(HDPE) and the electric field of 5-200kV/mm were tested. Conductivity characteristics experiments, in addition, using the mathematical formula of a variety of conductance mechanisms, the electric field-current density curves of the four kinds of polyethylene were fitted to analyze the conductance transition of the above four kinds of polyethylene in non-ohmic regions under different high field strengths. mechanism. The experimental results show that as the density of polyethylene increases, the crystallinity increases continuously, and the continuous increase of crystallinity causes the electric conduction flow under the same field strength to decrease significantly. The field strength corresponding to the two turning points in the conductance characteristic curve increases simultaneously. Large, the breakdown field strength increases; through analysis, it is found that in the high field, as the electric field increases, the conductance mechanism develops from the ohmic conductance of the low field strength region to the bulk effect of the high field strength region (Poole-Frenkel). Then the electrode effect to the high field strength (Schottky), and the threshold field strength of this conductance mechanism transition increases with the increase of crystallinity.

Herein, activated red mud particles are used as an adsorbent for adsorbing phosphorus. Different concentrations of HCl and deionized water are used for desorption tests, and the optimal desorption mechanism is investigated. The Langmuir isothermal model and pseudo-second-order kinetic linear model produce consistent results: the desorption is dominated by the surface desorption of the monomolecular layer, and chemical desorption limits the rate of surface desorption. The desorption thermodynamics indicates that the desorption of phosphorus by the desorbent is spontaneous and high temperature promotes desorption. The particle diffusion model demonstrates that the removal of phosphorus in the form of precipitation from the surface of an activated hematite particle adsorbent occurs primarily via a chemical reaction, and an analysis of the microscopic morphology indicates that the desorption process is primarily accompanied by the dissolution of the metal element Ca, followed by Al and Fe. The desorbent reacts with the active elements in red mud, and the vibration of the [SiO4]2− group calcite or aragonite group of calcium–iron garnet in the functional group disappears. The intensity of the wave peaks of the PO43− groups decreases considerably. Thus, desorption primarily involves the chemical desorption of the monomolecular layer.

In this study, modified red mud after phosphorus adsorption was used as the adsorbent, and hydrochloric acid and deionized water were used as desorbents to desorb phosphorus. The components in the adsorbent were optimized based on density functional theory, and adsorbent and desorbent models were established. Molecular dynamics simulation was performed to determine the phosphorus concentration before and after desorption, interaction energies, radial distribution function(RDF), mean-square displacement(MSD), and diffusion coefficient. The Monte Carlo method was used to simulate the desorption isotherm, desorption site, heat of desorption, and desorption energy. Simulation results showed that deionized water could only desorb phosphorus on the adsorbent surface, and the stability of the system deteriorated upon adding hydrochloric acid. Hydrochloric acid destroyed the ionic and hydrogen bonding between the O atoms in H2PO4− and reactive metal and oxygen atoms in the activated red mud particles. Moreover, the van der Waals force decreased considerably. The ionic and hydrogen bonds between H2PO4− and the surface of activated red mud particles were broken by hydrochloric acid, which accelerated the desorption of phosphorus from the adsorbent surface. The interaction between hydrochloric acid and phosphorus accelerated the diffusion, which decreased the adsorption capacity. Moreover, the desorption capacity increased with increasing temperature.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

The effects of exogenous inorganic [i.e., nitrate (NO3-)/ammonium (NH4+)] and organic [i.e., glutamate (Glu)/argine (Arg)] N alone and in combination on the accumulation of proline (Pro) in rice plant under trivalent chromium [Cr(III)] stress were studied through the mass balance matrix model (MBMM). ‘NH4+’ application showed the largest contribution to the Pro content in rice shoots under different concentrations of Cr(III), followed by ‘NO3-’, ‘Arg’, and ‘Glu’ application respectively. While, ‘Arg’ application displayed the largest contribution to the Pro content in roots under Cr(III) stress, followed by ‘NH4+’, ‘Glu’, and ‘NO3-’ application. Among the combination cases of N sources used, the application of ‘NH4++Arg’ showed the greatest contribution to the Pro content in both roots and shoots of Cr(III)-treated rice seedlings, while the application of ‘NO3-+Glu’ showed the least contribution to the Pro content in rice seedlings under Cr(III) stress. Results from this study indicated that the level of indigenous Pro in rice seedlings is quite sensitive to Cr(III) stress under different N sources, and mathematical modeling showed a reliable result to estimate the relationship between Pro content and N source application in rice plants in response to Cr(III) exposure .

Background: This study investigated the incidence, characteristics and functional outcomes associated with unplanned Acute Care Unit Readmissions (ACUR) during inpatient traumatic brain injury (TBI) rehabilitation in an Asian cohort. Methods: Retrospective review of electronic medical records from single rehabilitation unit was conducted from 1 Jan 2012 to 31 Dec 2014. Inclusion criteria were first TBI, aged >18 years, admitted < 6 months of TBI. ACUR were characterized into either of neurological, medical or neurosurgical subtypes. The main outcome measure was discharge Functional Independence Measure (FIM). Secondary outcomes included rehabilitation length of stay (RLOS). Results: Of 121 eligible TBI records, the incidence of ACUR was 14% (n=17), comprising neurologic (76.5%) and medical (23.5%) subtypes, occurring at median of 13 days (IQR 6, 28.5) after rehabilitation admission. Patients without ACUR had significantly higher admission mean (SD) FIM score compared to those with ACUR (FIM ACUR-negative 63.4 (21.1) vs FIM ACUR-positive 50.53(25.4), P =0.026). Significantly lower discharge FIM was noted in those with ACUR compared to those without. (FIM ACUR-positive 65.8(31.4) vs FIM ACUR-negative 85.4 (21.1), P = 0.023) Furthermore, a significant near-doubling of RLOS was noted in ACUR patients compared to non-ACUR counterparts [ACUR-positive median 55 days (IQR 34.50, 87.50) vs ACUR-negative median 28 days (IQR 16.25, 40.00), P = 0.002]. Conclusion: This study highlights the significant negative functional impact and lengthening of rehabilitation duration of ACUR on inpatient rehabilitation outcome for TBI.

Density functional theory (DFT) and coupled cluster theory (CCSD(T)) calculations are performed to investigate the geometric, electronic structures and chemical bonding of a series of Cu-doped zinc oxide clusters, CunZn3O3 (n = 1-4). The structural evolution of CunZn3O3 (n = 1-4) clusters are elaborated in our work. The planar seven-membered ring of CuZn3O3 cluster plays an important role in the structural evolution, that is, the Cu atom, Cu dimer (Cu2) and Cu trimer (Cu3) anchor on the CuZn3O3 cluster. The aggregate behavior of Cu atoms on Zn3O3 may offer insight into the study of Cu/ZnO-based catalysts. Additionally, it is found that the CunZn3O3 clusters become more stable as the Cu content (n) increases. Bader charge analysis points out that as the Cu atoms doping, the reducibility of Cu aggregation (Cun-1) on the CuZn3O3 cluster increases. Combined with the d-band centers and the surface electrostatic potential (ESP), the reactivity and the possible reaction sites of CunZn3O3 (n = 1-4) clusters are also illustrated.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Aflatoxin biosynthesis is correlated with oxidative stress and is proposed to function as a secondary defense mechanism to redundant intracellular reactive oxygen species (ROS). We find that the antioxidant gallic acid inhibits aflatoxin formation and growth in A. flavus in a dose-dependent manner. Global expression analysis (RNA-Seq) of gallic acid treated A. flavus showed that 0.8% (w/v) gallic acid revealed two possible routes of aflatoxin inhibition. Gallic acid significantly inhibited the expression of farB, encoding a transcription factor that participates in peroxisomal fatty acid β oxidation, a fundamental contributor to aflatoxin production. Secondly, the carbon repression regulator encoding gene creA was significantly down regulated by gallic acid treatment. CreA is necessary for aflatoxin synthesis and aflatoxin biosynthesis genes were significantly downregulated in DcreA mutants. In addition, the results of antioxidant enzyme activities and the lipid oxidation levels coupled with RNA-Seq data of antioxidant genes indicated that gallic acid may reduce oxidative stress through the glutathione- and thioredoxin-dependent systems in A. flavus.

2-Pyridone ligand-facilitated palladium-catalyzed direct C–H bond functionalization via the transient directing group strategy has become an attractive topic. Here we report a Pd-catalyzed direct β-C(sp3) –H arylation reaction of tertiary aliphatic aldehydes by using an α-amino acid as a transient directing group in combination with a 2-pyridone ligand.

Crop residue burning produces a lot of polluting gases and fine particles, endangering human health, damaging soil structure, and causing fire accidents. In addition to the impact of residue burning on the local environment, pollutants can spread with the wind to more distant areas and impact the air quality of surrounding areas, especially cities. Nevertheless, a comparative analysis of the impact of two common residue burning parameters, the number of residue fire points and residue burned area, on urban air quality indicators has not been reported. In this study, the correlation between these two different residue burning parameters on air quality in Daqing City was investigated comparatively using the Visible Infrared Imaging Radiometer Suite (VIIRS) fire point product, the Moderate-resolution Imaging Spectroradiometer (MODIS) burned area product, and buffer zone analysis. The association between MODIS burned area products and air quality index (AQI) was found to be around 0.8, with a maximum of 0.816 at a buffer zone radius of 50 km. Meanwhile, it was found that the correlation between the number of residue fire points extracted from the VIIRS active fire products and air quality was above 0.6, again with a maximum of 0.745 at a buffer radius of 50 km. Within other levels of buffer zones, the correlation between residue burned area and AQI was consistently higher than that between residue fire points and AQI. By comparing the correlation between VIIRS fire points, MODIS burned area, and AQI with the concentration of each pollutant, we found that the correlation between residue burned area and AQI and the concentration of each pollutant is higher. MODIS burned area monitoring, on the other hand, detects changes in the time series of images taken by satellite at two transit moments to obtain the new burned area and cumulative burned area during this period, allowing the monitoring of fire traces caused by fire points at non-transit moments. From analyzing the correlation between residue fire points, residue burned area, and the concentration of each pollutant (PM2.5, PM10, CO, NO2, SO2, O3), we found significant correlations between residue burning and PM2.5, PM10, CO, and NO2 concentrations, with the highest correlation (R2) of 0.81 for PM2.5. Moreover, the correlation between residue burned area and PM2.5, PM10, CO, and NO2 concentrations was significantly higher than that between the number of residue fire points and their concentrations.

Multi-object tracking (MOT) in airborne videos is a challenging problem due to the uncertain airborne vehicle motion, vibrations of the mounted camera, unreliable detections, size, appearance and motion of the moving objects as well as occlusions due to the interaction between the moving objects and with other static objects in the scene.To deal with these problems, this work proposes a four-stage Hierarchical Association framework for multiple object Tracking in Airborne video (HATA). The proposed framework combines data association-based tracking (DAT) methods and target tracking using a Compressive Tracking approach, to robustly track objects in complex airborne surveillance scenes. In each association stage, different sets of tracklets and detections are associated to efficiently handle local tracklet generation, local trajectory construction, global drifting tracklet correction and global fragmented tracklet linking. Experiments with challenging airborne video datasets show significant tracking improvement compared to existing state-of-art methods.

To conduct a precise impact assessment of marine diesel engines, a 200t floating impact platform was utilized to simulate realistic testing conditions. The testing generated the acceleration time curve and the impact response spectrum for the diesel engine. According to the applicable standards, the spectral velocity was chosen as the evaluation index, and an evaluation of the longitudinal, transverse, and vertical impact environment of the diesel engine was conducted. The shock factor interpolation method was corrected using the confidence interval based on normal distribution, and the interpolated confidence interval of the shock factor was determined. The findings reveal that: The 200t-class floating shock platform is capable of providing a reliable shock environment for diesel engine tests. The shock wave serves as the primary external force during the experiment, and the impact of bubble pulsation can be disregarded when assessing using the floating shock platform. To more accurately describe the experimental shock intensity when presented with dispersed data, the confidence interval can be utilized, and the resulting prediction formula provides a higher level of impact safety. The obtained conclusions can serve as a reference for predicting the shock environment of large shipboard equipment using the shock platform.

In this work, we proposed a novel design of microfluidic mixer utilizing the amplified Marangoni chaotic advection induced by AC continuous electrowetting of a metal droplet situated in electrolyte solution, due to the linear and quadratic voltage-dependence of flow velocity at small or large voltages, respectively. Unlike previous researchers exploiting the unidirectional surface stress with DC bias at droplet/medium interface for pumping of electrolyte where the resulting flow rate is linearly proportional to the field intensity, dominance of another kind of dipolar flow pattern caused by local Marangoni stress at the drop surface in sufficiently intense AC electric field is demonstrated by both theoretical analysis and experimental observation, which exhibits a quadratic growth trend as a function of the applied voltage. The dipolar shear stress merely appears at larger voltages and greatly enhances the mixing performance by inducing chaotic advection between the neighboring laminar flow. The mixer design developed herein, on the basis of amplified Marangoni chaotic advection around a liquid metal droplet at larger AC voltages, has great potential for chemical reaction and MEMS actuator applications, because of generating high-throughput and excellent mixing performance at the same time.

Five new cembrane-type diterpenes, lobocalines A–E (1–5), and four new steroids, lobocalines F–I (9–12), along with six known related compounds (6–8 and 13–15) were isolated from the Yalong Bay soft coral Lobophytum catalai. The structures of the new compounds were elucidated by extensive spectroscopic analysis, NMR calculation with DP4+ analysis, time-dependent density functional theory-electronic circular dichroism (TDDFT-ECD) calculations, X-ray diffraction analyses, and the comparison with the reported spectroscopic data of known compounds. Further, with the aid of X-ray diffraction analysis, the structure of lobocrasol B (15) was firmly revised as 15a. In in vitro bioassays, compound 2 showed moderate antibacterial activities against fish pathogenic bacteria Streptococcus parauberis KSP28 and Phoyobacterium damselae FP2244 with minimum inhibitory concentration (MIC) values of 8.7 and 17.3 µg/mL, respectively. All the steroids exhibited antibacterial activities against the S. parauberis KSP28 with MIC values ranging from 12.3 to 53.6 µg/mL. Compounds 2, 7 and 14 have remarkable inhibitory effects on the hemolysin production of Staphylococcus aureus, while compounds 8–12 have medium inhibitory effects on the pyocyanin production in Pseudomonas aeruginosa.

A series of novel N-n-butyl-1,8-naphthalimide derivatives were synthesized via a three-step reaction involving nucleophilic substitution and acylation. All of the compounds were characterized by IR, ¹H NMR, ¹³C NMR, MS, and elemental analysis, and the crystal structure of N-n-butyl-4-[N’,N’-bis(2`,4`-dichlorobenzoyl)ethylamino]-1,8-naphthalimide was determined. The π-π stacking interactions and hydrogen bonds between the two molecular core planes (naphthalimide ring) and the van der Waals forces between the flexible n-butyl groups resulted in a 3D long-chain structure. The UV-vis and fluorescence properties of the title compounds were investigated. The results indicated that the monosubstituted 1,8-naphthalimide derivatives bearing an electron-donating group on the benzene ring or a structure with a larger conjugative effect exhibited enhanced fluorescence properties.

A 'little brother' of pain, itch is an unpleasant sensation that creates a specific urge to scratch. To date, various machine-learning based image classifiers (MBICs) have been proposed for quantitative analysis of itch-induced scratch behaviour of laboratory animals in an automated, non-invasive, inexpensive and real-time manner. In spite of MBICs' advantages, the overall performances (accuracy, sensitivity and specificity) of current MBIC approaches remains inconsistent, with their values varying from ~50% to ~99%, for which the reasons underlying have yet to be investigated further, both computationally and experimentally. To look into the variation of the performance of MBICs in automated detection of itch-induced scratch, this article focuses on the experimental data recording step, and reports here for the first time that MBICs' overall performance is inextricably linked to the sharpness of experimentally recorded video of laboratory animal scratch behaviour. This article furthermore demonstrates for the first time that a linearly correlated relationship exists between video sharpness and overall performance (accuracy and specificity, but not sensitivity) of MBICs, and highlight the primary role of experimental data recording in rapid, accurate and consistent quantitative assessment of laboratory animal itch.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

Sewage sludge was utilized into biochar using the slow pyrolysis method. The biochar was then being used for ammonium removal. The sewage sludge biochar was produced at temperature of 550°C, 600°C, 650°C, 700°C and 750°C. A few characterization tests were carried out to study about the physical and chemical properties of the biochar. For instance, moisture and ash content analysis, FTIR spectroscopy, pH Zero Point Charge, biochar yield and SEM. As the pyrolysis temperature increased, the moisture content of SSB decreased while the ash content increased. The FTIR spectra of sewage sludge biochar showed that there were various organic functional groups on the surface of the biochar which were responsible for ammonium adsorption. Furthermore, through pH Zero Point Charge analysis, pH 7.0 was the most optimum pH for the adsorption test of ammonium. The optimum adsorbent dosage was 0.01g while optimum contact time was 150 minutes. Furthermore, 1.2ppm was the most optimum concentration for adsorption process. Based on the result of the characterization tests, SSB700 was the most effective biochar for ammonium adsorption. Based on the result of kinetic and isotherm analysis, the adsorption of ammonium ions usign sewage sludge biochar was a monolayer chemisorption process.

Land-cover classification that uses very-high-resolution (VHR) remote sensing images is a topic of considerable interest. Although many classification methods have been developed, there is still room for improvements in the accuracy and usability of classification systems. In this paper, a novel post-processing approach based on a dual-adaptive majority voting strategy (D-AMVS) is proposed for improving the performance of initial classification maps. D-AMVS defines a strategy for refining each label of a classified map that is obtained by different classification methods from the same original image and fusing the different refined classification maps to generate a final classification result. The proposed D-AMVS contains three main blocks. 1) An adaptive region is generated by extending gradually the region around a central pixel based on two predefined parameters (T1 and T2) in order to utilize the spatial feature of ground targets in a VHR image. 2) For each classified map, the label of the central pixel is refined according to the majority voting rule within the adaptive region. This is defined as adaptive majority voting (AMV). Each initial classified map is refined in this manner pixel by pixel. 3) Finally, the refined classified maps are used to generate a final classification map, and the label of the central pixel in the final classification map is determined by applying AMV again. Each entire classified map is scanned and refined pixel by pixel based on the proposed D-AMVS. The accuracies of the proposed D-AMVS approach are investigated through two remote sensing images with high spatial resolutions of 1.0 and 1.3 m, respectively. Compared with the classical majority voting method and a relatively new post-processing method called general post-classification framework, the proposed D-AMVS can achieve a land-cover classification map with less noise and higher classification accuracies.

Three new cembranoids (1–3) and a new casbanoid (4), along with three known analogues (5–7), have been isolated from the soft coral Sinularia nanolobata collected off Ximao Island. The structures including the absolute configurations of new compounds were established by extensive spectro-scopic data analysis, time-dependent density functional theory/electronic circular dichroism (TDDFT-ECD) calculations and the comparison with spectroscopic data of known compounds. In in vitro bioassay, compounds 1 and 5 exhibited moderate cytotoxic activities against human erythroleukemia (HEL) cells line with IC50 values of 37.1 and 42.4 uM, respectively.

Osteoarthritis (OA) has become one of the most common disabilities among elders, especially in female. Obesity and mechanical injury causing OA are attributed to joint loading, cartilage disintegration, bone loss and inflammation as well. Several strategies used for treatment OA including non-pharmacological and pharmacological. Fucoidan possesses several bioactivities such as antitumor, antiviral, anticoagulation, anti-obesity, and immunomodulation. This study aims to investigate the effect of fucoidan in surgery-induced OA on diet-induced obesity rats. OA was induced by anterior cruciate ligament transection and partial medial meniscectomy (ACLT+MMx). Male SD rats were fed high-fat diet (HFD) for 4 weeks to induce obesity before ACLT+MMx to induce OA. OA rats were administered with intragastric water or fucoidan in three different concentrations (32 mg/kg, 64 mg/kg, and 320 mg/kg) after the surgeries for 40 days with HFD. We observed that the swelling in knee joint was alleviated and hind paw weight distribution was rectified after feeding fucoidan, with no significant effect on weight gain and feed intake. Fucoidan administration indicated no significant variation on HDL-Cholesterol level, but reduced plasma triglycerides and LDL-Cholesterol level. In addition, weight-bearing tests showed improvement in the fucoidan-treated group. Our results suggested that fucoidan may improve meniscal/ligamentous injury and obesity-induced OA.

The phylogenetic relationships among the Peninsular Malaysian orchid genus Coelogyne were studied by morphological characteristics and by sequencing the internal transcribed region (ITS) from the nuclear ribosomal DNA (nrDNA). Coelogyne is a large genus of about 200 species distributed in pantropical areas from the Himalayas, Sri Lanka, India, Southern China and throughout South East Asia to Papua New Guinea. The widely accepted previous classification system was exclusively based on floral morphology. There were very few molecular systematic studies of Coelogyne done in Peninsular Malaysia thus far. In this study, 59 Coelogyne taxa were collected from throughout Peninsular Malaysia and 57 of them were identified to the species level. To study the phylogeny of this genus, morphological characters were utilized together with molecular evidences to generate the systematic hypotheses. Cluster analysis was performed using both the vegetative and floral characters. The results showed that three sections of Peninsular Malaysian Coelogyne, namely Longifoliae, Speciosae and Fuliginosae were sister groups which were more closely related by forming one clade than they were with the other sections. Another clade consisted of four other sections, namely Flaccidae, Coelogynae, Tomentosae and Verrucosae. Molecular phylogenies obtained by using the Neighbour Joining method revealed the close relationship between the sections Tomentosae and Verrucosae, whereas usage of the Maximum Likelihood method demonstrated that three sections namely Longifoliae, Speciosae and Fuliginosae were sister groups since they formed a single clade.

In India, particularly within its North-Eastern territories, the occurrence of landslides triggered by post-dry period rainfall events is a significant concern, with the phenomena persistently causing extensive damage to both life and infrastructure. Despite the inevitability of such natural disasters, it is understood that the impact they exert can be substantially mitigated through the implementation of pre-emptive measures. Critical to the endeavour of landslide prevention is the application of a spectrum of mitigation strategies, predicated upon a foundational analysis of slope stability to ascertain critical surfaces for intervention. This investigation delves into the dynamics of partially saturated soils, a condition commonly resultant from the prolonged dry periods preceding the monsoonal rains. The study's focal point is an experimental examination conducted on soil samples to assess parameters such as soil matric suction and unconfined compressive strength across varying degrees of saturation and density, alongside performing analyses of slope failure incidents after dry period during the 2017 monsoon in the Lunglei district, Mizoram based on some established data. The Soil-Water Characteristic Curve (SWCC), derived from soil suction measurements employing the ASTM D5298-10 standard, utilizes a contact filter paper method and serves to delineate the moisture transition phases of the slope. To replicate the desiccation of the soil slope after monsoonal rains, a microwave drying technique based on the ASTM standard was employed to prepare unsaturated soil samples for Unconfined Compressive Strength (UCS) testing. The integrity of the slope was evaluated in a temporal context, before and after rainfall events of varied intensities throughout the calendar year, utilizing a blend of numerical modeling and empirical laboratory investigations. The persistence of real onsite slope failures underscores the necessity for a numerical analysis approach to unravel the underlying factors causing slope instability, especially given the absence of prior stability assessments for the landslide in question. An evaluation of SWCC curves, UCS tests on partially saturated soil at different densities and saturation and the utilization of the benchmark data collected in 2017 on the shallow transitional landslide in Lunglei, Mizoram caused by intense monsoonal precipitation, are central key data and information used to carry out this research. Rainfall data for Lunglei, sourced from the Mizoram Meteorological Department, facilitated a real-time monsoonal data-driven numerical analysis. This analysis elucidated the pivotal role of rainfall in inducing slope failure, indicating a marked destabilization of the slope after precipitation events. The implications of these findings are far-reaching, suggesting a foundational basis for the development of an advanced landslide early warning system, thereby enhancing disaster preparedness, and mitigating potential damages.

With the swift advancement of wearable electronic devices and the electronic textile industry, the energy storage components of these devices must possess the capability to maintain stable mechanical and chemical properties even after undergoing multiple bending or tensile deformations. This circumstance has expedited research efforts toward novel materials, processing techniques, and designs for flexible energy storage devices. Among the myriad of materials investigated thus far, biomass-derived architectures have garnered significant attention due to renewability, cost-effectiveness, and abundance in earthly resources. Notably, flexible carbon membrane/ monolithic derived from biomass serve as a particularly promising option for self-supporting electrodes, align seamlessly with the requirements of next-generation electronic devices, and obviate the need for additional costs, unnecessary weight, and the high contact resistance that additive insulating adhesives may entail. This review delves into the comprehensive analysis of biomass feedstocks and methodologies employed in the synthesis of flexible self-supporting carbon electrodes. Subsequently, the advancements in their application in energy storage devices are elucidated. Finally, an outlook on the potential of biomass self-supported carbon architectures and the challenges they face is provided.

Molten salt electrolysis stands as an indispensable technique for the production of rare earth metals, where the judicious distribution of the electric field within the electrolytic cell is paramount for ensuring the seamless operation of the electrolysis process. This study introduces a pioneering approach by integrating the Nernst-Planck equation with the Butler-Volmer equation, thereby devising a holographic electric field model tailored for the electrolysis of the NdF3-LiF molten salt system. The paper presents pioneering experimental measurements concerning the potential distribution and voltage drop characteristics within a 6kA rare earth electrolytic cell, elucidating the interplay between decomposition voltage and current density, which substantiates the model's precision. Our findings unveil that, under operational conditions of 4010 amperes, the 6kA electrolytic cell incurs a total voltage drop of 6.3 volts, delineating a melt voltage drop of 4.43 volts, an ohmic voltage drop of 0.248 volts, and an interfacial voltage drop of 1.622 volts at the electrode-electrolyte junction. The discrepancy in error is confined to within 0.3% of the actual measured voltage of 6.28 volts.The simulation outcomes from the holographic electric field model have been confirmed to precisely and comprehensively reflect the characteristics of the electric field distribution during the rare earth molten salt electrolysis process, offering valuable theoretical insights for practical manufacturing applications.

We report on the role of synergistic polarization of Ba0.9Sr0.1TiO3 (BST) nanoparticles in sulfur cathodes to enhance the redox kinetics of polysulfides for high-capacity Li-S batteries. Ferroelectric nanoparticles are known to significantly improve the electrochemical performance of Li-S batteries due to their inherent self-polarization and high adsorption capacity towards polysulfides. X-ray diffraction spectra confirmed the tetragonal symmetry (c/a=1.0073), while Raman spectroscopic analysis validated the presence of tetragonal orientation Raman modes in BST-modified composites. Scanning electron microscope (SEM) images showed a homogeneous distribution of BST in the sulfur cathode system, with grain sizes ranging from 1 to 1.5 μm. Notably, the BST-coupled S50BST30CB10PVDF10 composite cathode achieved a capacity of approximately 820 mAh/g at 100 mA/g, maintaining stability over 100 cycles, demonstrating improved electrochemical performance. Two distinct plateaus between 2.3 V to 2.0 V and 2.0 V to 1.5 V further underscore the superior performance of BST ferroelectric nanoparticles in enhancing the redox kinetics of Li-S batteries. By leveraging the favourable affinity of polar substances towards polysulfides, we aimed to create a more stable reactive environment within the cathodic site, effectively trapping polysulfide intermediates through the synergistic polarization of BST nanoparticles. The synergistic polarization induced by the asymmetric crystal structure of ferroelectrics is anticipated to generate internal electric fields, enhancing chemisorption with heteropolar reactive. The observed high cyclic stability further validates the efficacy of these composite cathodes in mitigating the polysulfide shuttle effect, offering promising prospects for advancing Li-S battery technology.

Aborycin is a type I lasso peptide with a stable interlocked structure, offering a favorable framework for drug development. The aborycin biosynthetic gene cluster gul from marine sponge-associated Streptomyces sp. HNS054 was cloned and integrated into the chromosome of S. coelicolor hosts with different copies. The 3-copy gul-integration strains S. coelicolor M1346::3gul showed better production than one-copy or 2-copy gul-integration strains, and the total titer reached approximately 10.4 mg/L, i.e., 2.1 times that of the native strain. Then, five regulatory genes, phoU (SCO4228), wblA (SCO3579), SCO1712, orrA (SCO3008) and gntR (SCO1678), which were reported to have negative effects on secondary metabolism, were further knocked out from the M1346::3gul genome by CRISPR/Cas9 technology. While the ΔSCO1712 mutant showed a significant decrease (4.6 mg/L) and the ΔphoU mutant showed no significant improvement (12.1 mg/L) in aborycin production, the ΔwblA, ΔorrA and ΔgntR mutations significantly improved the aborycin titers to approximately 23.6 mg/L, 56.3 mg/L and 48.2 mg/L, respectively, which were among the highest heterologous yields for lasso peptides in both Escherichia coli systems and Streptomyces systems. Thus, this study provided important clues for future studies on enhancing antibiotic production in Streptomyces systems.

Codon use bias is an important characteristic in the process of genetic information transmission of species. With the publication of the genome of C. panzhihuaensis, it is of great significance to investigate the codon use bias for understanding the genetic evolution of this species and for molecular breeding. In this study, Perl language and CodonW 1.4.2 software was used to systematically analyze the coding gene sequences of the C. panzhihuaensis genome, obtain the characteristics of codon use, and identify the sources of variation affecting codon use. The results showed that GC3s content, GCall content, and ENC value were 46.75%, 47.67%, and 52.8 respectively. As the first seed plant, the GC3 content of Cycas is similar to that of most gymnosperms and most dicotyledons, but considerably different from that of monocotyledons.RSCU value was greater than 1, among which 21 codons ended in U or A. Enc-plot analysis, PR2-plot neutral plot analysis, and correlation coefficient analysis of Axis1 with GC3s and CAI revealed that the codon bias was mainly affected by natural selection, but also by mutation pressure and other factors. Thirty-one optimal codons of Cycas genes were screened. This research can provide a reference for the phylogeny and genome codon evolution of Cycas.

The need for miniaturized shear force sensors is expanding, particularly for biomedical applications. Examples include measuring interfacial shear stresses between a human and an external device (e.g., footwear or a prosthesis). However, there are considerable challenges in designing a shear sensor for these applications due to the need for a small package, low power requirements, and resistance to interference from motion artifact and electromagnetic fields. This paper presents the design, fabrication, and characterization sensor that measures two-axis shear force by detecting displacement between a color panel and a red, green, and blue light-sensing photodiode. The sensor response to applied displacements and forces was characterized under benchtop testing conditions. We also present the design of a prototype wireless version of the sensor for integration into footwear. The sensor exhibited strong agreement with gold standard measurements for two axis shear displacements (R2>0.99, RMSE≤5.0 µm) and forces (R2>0.99, RMSE≤0.94 N). This performance, along with the sensor’s scalability, miniaturized form, and low power requirements make it well-suited a variety of biomedical applications.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

This article analyzes in detail the influence of Jupiter on the measurement of the gravitational constant. Including a specific estimate of the change in the gravitational constant caused by the change of the earth's orbital position every half month. The influence of Jupiter's perihelion and aphelion on the gravitational constant is also estimated. On this basis, this article analyzes the data with specific time records such as BIPM-01, BIPM-14, JILA-10, UCI-14, HUST-09. The analysis results show that after considering the influence of Jupiter, the experimental results have been significantly improved.

Porous coatings on prosthetic implants encourage implant fixation. Enhanced fixation may be achieved using a magneto-active porous coating that can deform elastically in vivo on application of an external magnetic field, straining in-growing bone. Such coating, made of 444 ferritic stainless steel fibres, was previously characterised in terms of its mechanical and cellular responses. In this work, co-cultures of human osteoblasts and endothelial cells were seeded into a novel fibrin-based hydrogel embedded in a 444 ferritic stainless steel fibre network. Albumin was successfully incorporated into fibrin hydrogels improving the specific permeability and the diffusion of fluorescently-tagged dextrans without affecting their Young’s modulus. The beneficial effect of albumin was demonstrated by upregulation of osteogenic and angiogenic gene expression. Furthermore, mineralisation, extracellular matrix production and formation of vessel-like structures were enhanced in albumin-enriched fibrin hydrogels compared to fibrin hydrogels. Collectively, the results indicate that the albumin-enriched fibrin hydrogel is a promising bio-matrix for bone tissue engineering and orthopaedic applications.

The papaya mealybug Paracoccus marginatus is an invasive, polyphagous pest and poses a quarantine threat to tropical and subtropical countries. Infested commodity internationally should be undergoing phytosanitary treatment, while irradiation is recommended to replace methyl bromide fumigation. Dose-response tests were conducted on the 2-, 4-, and 6-d-old eggs and gravid females of P. marginatus using the X-ray radiation doses of 15–105 Gy with an interval of 15 Gy, respectively. Radiotolerance was compared using fiducial overlapping and lethal dose ratio (LDR) test, resulting in insignificant difference except for LDR test at LD90 (leading 90% mortality at 95% confidence level (CL)); the estimated dose for 99.9968% mortality at 95% CL was 176.5–185.2 Gy, which was validated in the confirmatory tests using gamma irradiation because gammy and X-rays have equal biological effect on pests. Therefore, a total of estimating 60,386 gravid females of papaya mealybug irradiated with 146.8–185.0 Gy resulted in no F1 nymphs developing. Eggs can therefore be used as an alternative to gravid females for dose-response tests; the recommended minimum dose for phytosanitary treatment of P. marginatus on infested commodity is 185 Gy, with treatment efficacy ≥ 99.9950% at 95% CL.

The design and fabrication of low-cost catalysts for highly efficient oxygen reduction is of paramount importance for various renewable energy-related technologies, such as fuel cells and metal-air batteries. Herein, we report the in situ growth of Fe3N nanoparticles encapsulated N-doped carbon nanotubes on the surface of flexible biomass-derived carbon cloth (Fe3N@CNTs/CC) via a simple one-step carbonization process. Taking advantage of its unique structure, Fe3N@CNTs/CC was employed as a self-standing electrocatalyst for oxygen reduction reaction (ORR) and possessed high activity as well as excellent long-term stability and methanol resistance in alkaline media. Remarkably, Fe3N@CNT/CC can directly play the role of both gas diffusion layer and electrocatalytic cathode in a zinc-air battery without additional means of catalyst loading, and display higher open circuit voltage, power density, and specific capacity in comparison with the commercial Pt/C catalyst. This work is anticipated to inspire the design of cost-effective, easy-preparation, and high-performance air electrodes for advanced electrochemical applications.

Taking Korla fragrant pear as the research object, single factor testing and water and fertilizer coupling testing were conducted. Under the premise of the drip irrigation mode, the effects of water, nitrogen, and phosphorus on the growth, fruit quality, and yield of Korla Fragrant Pear were studied to provide a theoretical basis for efficient water and fertilizer management. Among them, the single factor test set water, nitrogen and phosphorus as the three factors, and each factor was set at five levels, namely, water (W1, 5460 m3·hm−2;W2, 5880 m3·hm−2;W3,6300 m3·hm−2; W4, 6720 m3·hm−2; W5, 7140 m3·hm−2), nitrogen (N1, 150 kg N·hm−2;N2, 225 kg N·hm−2; N3, 300 kg N·hm−2; N4, 375 kg N·hm−2; N5, 450 kg N·hm−2), phosphorus (P1,75 kg P2O5·hm−2; P2, 150 kg P2O5·hm−2; P3, 225 kg P2O5·hm−2; P4, 300 kg P2O5·hm−2; P5, 375 kg P2O5·hm−2). The results showed that the total nitrogen and total phosphorus contents in leaves under the W3, W4, N3, N4, P3, and P4 treatments were significantly higher than those under other treatments, and the fruit quality was better. Therefore, the W3, W4, N3, N4, P3, and P4 treatments were selected as the water and fertilizer inputs for the water–fertilizer coupling test for Korla fragrant pear. Eight treatments were set up in the water and fertilizer coupling test: Treatment 1 (T1, W3N3P3), Treatment 2 (T2, W3N3P4), Treatment 3 (T3, W3N4P3), Treatment 4 (T4,W3N4P4), Treatment 5 (T5, W4N3P3), Treatment 6 (T6, W4N3P4), Treatment 7 (T7, W4N4) P3), and Treatment 8 (T8, W4N4P4). The results showed that the leaf area index of the T1, T2, T3, and T4 treatments was significantly higher than that of the other treatments at maturity. The T3 treatment resulted in the highest fruit yield, single fruit weight, and primary fruit rate. The results of the grey correlation degree analysis of fruit quality showed that T3 treatment had the highest degree of correlation and ranking of each fruit quality index, indicating that T3 treatment had the highest fruit quality. Detailed investigation of pear tree growth and fruit quality showed that the T3 treatment (375 kg·hm−2 nitrogen application, 225 kg·hm−2 phosphorus application and 6300 m3·hm−2 irrigation) had the best fruit growth and development performance, and the sweet pear fruit quality was the best.

This paper investigates the hydroelastic responses of offshore floating solar photovoltaic farms (OFPVs) to minimize structural motion. The OFPV usually occupies a large sea space in the order of hectares and due to its huge structural length-to-thickness ratio, the structural deformation under wave action has to be taken into consideration. The flexible deformation of the structure under hydrodynamic loading is termed the hydroelastic response. Due to the relatively long structural length with respect to the encountering wavelength, the diffraction and radiation of waves have to be taken into account to accurately represent the hydrodynamic loadings on the floating platform. The numerical model is first validated by comparing the eigenvalues and eigenvectors of the OFPV obtained from the proposed numerical scheme with their counterparts obtained from an established finite element software. This is followed by the investigation of the hydroelastic response of various OFPVs designed in varying layout configurations. The various layout configurations are obtained by altering the floating modular units’ dimensions as well as the spacing of the OFPVs when deployed adjacent to each other. The optimal configuration that gives the best performance in terms of the overall smallest response, known as compliance, is then suggested. The results suggest that a longish OFPV layout has a lower hydroelastic response and the motion could be further reduced by increasing the global flexural stiffness via layout arrangement.

Taking Korla fragrant pear as the research object, single factor testing and water and fertilizer coupling testing were conducted. Under the premise of the drip irrigation mode, the effects of water, nitrogen, and phosphorus on the growth, fruit quality, and yield of Korla Fragrant Pear were studied to provide a theoretical basis for efficient water and fertilizer management. Among them, the single factor test set water, nitrogen and phosphorus as the three factors, and each factor was set at five levels, namely, water (W1, 5460 m3·hm−2;W2, 5880 m3·hm−2;W3,6300 m3·hm−2; W4, 6720 m3·hm−2; W5, 7140 m3·hm−2), nitrogen (N1, 150 kg N·hm−2;N2, 225 kg N·hm−2; N3, 300 kg N·hm−2; N4, 375 kg N·hm−2; N5, 450 kg N·hm−2), phosphorus (P1,75 kg P2O5·hm−2; P2, 150 kg P2O5·hm−2; P3, 225 kg P2O5·hm−2; P4, 300 kg P2O5·hm−2; P5, 375 kg P2O5·hm−2). The results showed that the total nitrogen and total phosphorus contents in leaves under the W3, W4, N3, N4, P3, and P4 treatments were significantly higher than those under other treatments, and the fruit quality was better. Therefore, the W3, W4, N3, N4, P3, and P4 treatments were selected as the water and fertilizer inputs for the water–fertilizer coupling test for Korla fragrant pear. Eight treatments were set up in the water and fertilizer coupling test: Treatment 1 (T1, W3N3P3), Treatment 2 (T2, W3N3P4), Treatment 3 (T3, W3N4P3), Treatment 4 (T4,W3N4P4), Treatment 5 (T5, W4N3P3), Treatment 6 (T6, W4N3P4), Treatment 7 (T7, W4N4) P3), and Treatment 8 (T8, W4N4P4). The results showed that the leaf area index of the T1, T2, T3, and T4 treatments was significantly higher than that of the other treatments at maturity. The T3 treatment resulted in the highest fruit yield, single fruit weight, and primary fruit rate. The results of the grey correlation degree analysis of fruit quality showed that T3 treatment had the highest degree of correlation and ranking of each fruit quality index, indicating that T3 treatment had the highest fruit quality. Detailed investigation of pear tree growth and fruit quality showed that the T3 treatment (375 kg·hm−2 nitrogen application, 225 kg·hm−2 phosphorus application and 6300 m3·hm−2 irrigation) had the best fruit growth and development performance, and the sweet pear fruit quality was the best.

The features of a class of cubic curves with a shape factor are analyzed by means of the theory of envelope and topological mapping. The effects of the shape factor on the cubic curves are made clear. Necessary and sufficient conditions are derived for the curve to have one or two inflection points, a loop or a cusp, or to be locally or globally convex. Those conditions are completely characterized by the relative position of the edge vectors of the control polygon and the shape factor. The results are summarized in a shape diagram, which is useful when the cubic parametric curves are used for geometric modeling. Furthermore we discussed the influences of the shape factor on the shape diagram and the ability for adjusting the shape of the curve.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

It is well known that human activities and climate change have increased steppe habitat loss and fragmentation in Northwest China. Carabid beetles are often used as bioindicators of environmental change because they are extremely sensitive to disturbance. We chose 42 landscapes (18 fragmented and 24 continuous) in both desert and typical steppes of Northwest China to examine the influence of habitat loss and fragmentation on carabid beetle communities. The results showed the largest correlation coefficient between carabid communities and landscape compositions within a 7-km spatial scale in both desert and typical steppes. Further, the response of carabid communities to habitat fragmentation was species-specific in both desert and typical steppes. Habitat fragmentation in the desert steppe had positive effects on the richness and abundance of carabid communities, while in the typical steppe, the effects were negative. Additionally, habitat fragmentation significantly decreased the abundance of two common carabid species in the desert steppe. Therefore, the effects of habitat fragmentation on carabid biodiversity differ with species characteristics and habitat traits, where plant communities, soil structure, and microclimate vary in the different steppe types. The results of this study provide experimental evidence and technical support for biodiversity conservation management in the steppes of Northwest China.

Schistosoma infection in snails can be monitored by microscopy or indirectly by sentinel mice. As both these approaches sometimes miss infections, more sensitive tests are needed, particularly in low-level transmission settings. In this study, the loop-mediated isothermal amplification (LAMP) technique, designed to detect a specific 28S ribosomal S. japonicum gene with high sensitivity, was compared to microscopy using snail samples from 51 areas endemic for schistosomiasis in five Chinese provinces. The results were compared with those by polymerase chain reaction (PCR) adding DNA sequencing as a reference when needed. The testing of pooled snail samples showed that a dilution factor of 1/50, i.e., one infected snail plus 49 non-infected ones, would still result in a positive reaction after the recommended number of amplification cycles. Testing a total of 232 pooled samples, emanating from 4,006 snail specimens, with the LAMP assay showed a 6.5% rate of infection, while traditional microscopy found only 0.04% positive samples in the same materials. Parallel PCR analysis confirmed the diagnostic accuracy of the LAMP assay, with DNA sequencing even giving LAMP a slight lead. Microscopy and the LAMP test were carried out at local schistosomiasis-control stations demonstrating that the potential of the latter assay to serve as a point-of-care (POC) test with results available within 60–90 minutes, while the more complicated PCR test had to be carried out at the National Institute of Parasitic Diseases (NIPD) in Shanghai, China. In conclusion, LAMP was found to be clearly superior to microscopy and as good as, or better, than PCR. Application of LAMP testing would be useful for surveillance and risk prediction as it requires less time than other techniques and can be used under field conditions, which improves and accelerates schistosomiasis control.

Two-dimensional (2D) of transition metal dichalcogenides (TMDCs) are potential candidates for thermoelectric (TE) applications due to their unique structural properties. In this paper, we constructed an 2D monolayer TMDCs semiconductor γ-PbSn2(X=S, Se, Te) and first-principles calculations and Boltzmann transport theory are used to study the thermoelectric performance. We found that γ-PbSnX2 had an ultra-high carrier mobility up to 4.04×103 cm2V−1s−1 leading to a metal-like electrical conductivity. Meanwhile, γ-PbSnX2 both have high Seebeck coefficients, resulting in high power-factors, and also shows intrinsic low lattice thermal conductivity of 6-8 W/mK at room temperature. The lower lattice thermal conductivity and high power-factors resulted in excellent thermoelectric performance. The high ZT values of γ-PbSnS2 and γ-PbSnSe2 were as high as 2.65 and 2.96 at 900 K, respectively. The result suggests that the monolayer γ-PbSnX2 are better candidates for excellent thermoelectric performance.

Exosomes are associated with cancer progression, pregnancy, cardiovascular diseases, central nervous system–related diseases, immune responses and viral pathogenicity. However, study on the role of exosomes in the immune response of teleost fish, especially antiviral immunity, is limited. Herein, serum-derived exosomes from mandarin fish were used to investigate antiviral effect for the exosomes of teleost fish. Exosomes were isolated from mandarin fish serum by ultracentrifugation could internalize into Mandarin fish fry (MFF-1) cells and inhibited Infectious spleen and kidney necrosis virus (ISKNV) infection. To further investigated the underlying mechanisms of exosomes in inhibiting ISKNV infection. The protein composition of serum-derived exosomes was by analysis mass spectrometry and found that myxovirus resistance 1 (Mx1) was incorporated in the exosomes. Furthermore, the scMx1 protein was proved transferred to the recipient cells though the exosomes. Our results found that the serum-derived exosomes from mandarin fish could inhibit ISKNV replication and suggested an underlying mechanism of the serum-derived exosomes antivirus is that serum-derived exosomes incorporation of the Mx1 protein into exosomes and delivery into recipient cells. This study provided an evidence for the important antiviral role of exosomes in the immune system of teleost fish.

SARS-CoV-2, the newly identified human coronavirus causing severe pneumonia epidemic, was probably originated from Chinese horseshoe bats. However, direct transmission of the virus from bats to humans is unlikely due to lack of direct contact, implying the existence of unknown intermediate hosts. Angiotensin converting enzyme 2 (ACE2) is the receptor of SARS-CoV-2, but only ACE2s of certain species can be utilized by SARS-CoV-2. Here, we evaluated and ranked the receptor-utilizing capability of ACE2s from various species by phylogenetic clustering and sequence alignment with the currently known ACE2s utilized by SARS-CoV-2, predicting potential intermediate hosts of SARS-CoV-2.

As a dominant mangrove species, Kandelia obovata is distributed in an intertidal marsh with an active H₂S release. Whether H₂S participates in the salt tolerance of mangrove plant is still ambiguous although increasing evidence have demonstrated that H₂S functions in plant responses to multiple abiotic stresses. In this study, as an H₂S donor, NaHS was used to investigate the regulatory mechanism of H₂S on salt tolerance of K. obovata seedlings using a combined physiological and proteomic analysis. The results showed that the reduction in photosynthesis (Pn) caused by 400 mM NaCl was recovered by the addition of NaHS (200 μM). Furthermore, the application of H₂S enhanced the quantum efficiency of PSII and the membrane lipid stability, implying that H₂S is beneficial to the survival of K. obovata seedlings under high salinity. We further identified 37 differentially expressed proteins by proteomic approaches under salinity and NaHS treatment. Among them, the proteins related to photosynthesis, primary metabolism, stress response and hormone biosynthesis were primarily enriched. The physiological and proteomic results highlighted that exogenous H₂S up-regulated photosynthesis and energy metabolism to help K. obovata to cope with high salinity. Specifically, H₂S increased photosynthetic electron transfer, chlorophyll biosynthesis and carbon fixation in K. obovata leaves under salt stress. Furthermore, the abundances of other proteins related to metabolic pathway, such as antioxidation (APX, CSD2, PDX1), protein synthesis (HSP, Cpn 20), nitrogen metabolism (GS2, GS1:1), glycolysis (PGK, TPI), AsA-GSH cycle were increased by H₂S under high salinity. These findings provide new insights into the roles of H₂S in the adaptations of mangrove plant K. obovata to high salinity environment.

Fracture grouting has been a widely used mitigation measure against seepage in the Yellow River Embankment. However, there is currently a lack of systematic investigation for evaluating the anti-seepage effectiveness of fracture grouting employed in this longest river embankment in China. Therefore, in this work, laboratory and in-situ experiments are carried out for investigating the reinforcement effect of fracture grouting in the Jinan Section of the Yellow River Embankment. In particular, firstly, the laboratory tests concentrate on studying the optimum strength improvement for cement-silicate grout by varying the content of backfilled fly ash and bentonite as admixtures. Flexural strength and Scanning Electron Microscope photographs are investigated for assessing the strength and compactness improvement. Subsequently, based on the obtained optimum admixtures content, in-situ grouting tests are carried out in the Jinan Section of the Yellow River Embankment to evaluate the anti-seepage effectiveness of fracture grouting, where geophysical prospecting and pit prospecting methods are employed. Laboratory results show that, compared with pure cement-silicate grouts, the gelation time of the improved slurry is longer and gelation time increases as fly ash content increases. The optimum mixing proportion of the compound cement-silicate grout is 70% cement, 25% fly ash and 5% bentonite, and the best volume ratio is 2 for the investigated cases. Geophysical prospecting using the Ground Penetrating Radar and High Density Resistivity methods can reflect the anti-seepage effectiveness of fracture grouting on site. It shows that the grouting material mainly flows along the axial direction of the embankment. The treatment that is used to generate directional fracture is proved to be effective. The injection hole interval distance is suggested to be 1.2 m, where the lapping effect of the grouting veins is relatively significant. For the investigated cases, the average thickness of the grouting veins is approximately 6.0 cm and the corresponding permeability coefficient is averagely 1.6 × 10⁻⁶ cm/s, which meets the anti-seepage criterion in practice.

As with every new technology, safety demonstration is a critical component of bringing products to market and gaining public acceptance for cultured meat and seafood. This manuscript develops research priorities from the findings from a series of interviews and workshops with governmental scientists and regulators from food safety agencies in fifteen jurisdictions globally.  The interviews and workshops aimed to identify the key safety questions and priority areas of research. Participants raised questions about which aspects of cultured meat and seafood production are novel, and the implications of the paucity of public information on the topic. Novel parameters and targets may require the development of new analytical methods or adaptation and validation of existing ones, including for a diversity of product types and processes. Participants emphasized that data sharing of these efforts would be valuable, similar to those already developed and used in the food and pharmaceutical fields. Contributions to such databases from the private and public sectors would speed general understanding as well as efforts to make evaluations more efficient. In turn, these resources, combined with transparent risk assessment, will be critical elements of building consumer trust in cultured meat and seafood products.

An outbreak of a virus-like disease has caused severe damage to noni plants (Morinda citrifolia L.) in Xishuangbanna area of China's southwestern Yunnan province since 2015. The diseased plants displayed typical mosaic symptom with light and dark green patches on leaves. Flexuous filamentous virus particles of about 800 nm in length were observed from the leaf saps by transmission electron microscope. Illumina transcriptomic sequencing further revealed the presence of a potyvirus and its near complete genome was obtained from de novo assembly. The complete genome of 9,659 nts was obtained by Sanger sequencing of eight amplicons generate by RT-PCR and 5’ and 3’ RACE. BLASTp analysis of the polyprotein sequence showed that the virus was most closely related to Tobacco vein banding mosaic virus (TVBMV), but these two viruses only shared 50.7% amino acid sequence similarity. Both phylogenetic analyses of the polyprotein and CP amino acid sequences indicated that this virus is a member of genus Potyvirus. However, the low sequence homology with all known potyviruses established this virus as a new species in the genus, tentatively named as Noni mosaic virus (NoMV). Our field surveys showed that 100% of the symptomatic samples and 28.57% of the asymptomatic samples were infected with this novel potyvirus. Aphids collected from diseased leaves were also detected carrying the virus. In summary, our data indicated that a novel species of potyvirus, NoMV, is prevalent in Yunnan, China and is associated with an emerging mosaic disease on M. citrifolia.

Physical inactivity is a well-known risk factor for various non-communicable diseases (NCDs). Sufficient physical activity (PA) is essential for the prevention of NCDs and thus it is imperative to study the current status of PA and its influencing factors among rural residents in China. A population-based survey was conducted in rural areas of Shandong, Shanxi and Yunnan Provinces using a stratified random sampling method. The International Physical Activity Questionnaire Short Form (IPAQ-S) was used to collect the data on PA. A total of 3780 rural residents participated in the survey. The result showed that 22.2% of rural residents were physical inactivity. The proportion of rural residents reporting practice of physical exercise was 54.4%. The most frequently performed physical exercise was walking/brisk walking(78.3%).Binary logistic regression analyses showed that being female, people at age between 15 to 34 years or 60 years old and above, employees of governmental departments/retirees, school students, the unemployed, people with NCDs were risk factors of PA and ethnic minority groups,smoking and alcohol consumption were risk factors of physical exercise. Health promotion programme aiming at increasing people’s PA in rural China is needed and it should focus on the populations groups of the female, people at age 60 years and above ,school students, the unemployed, and people with NCDs.

The genus Amomum encompasses six medicinal species that are extensively utilized and have a significant historical background. Due to their morphological similarities, however, the presence of counterfeit and substandard products remains a challenge. Accurate plant identification is therefore essential to address these issues. This study utilized 11 newly sequenced samples along with extensive data from NCBI to perform molecular identification of these six species. The plastomes of Amomum displayed a typical quadripartite structure with conserved gene content, yet showed independent variations in the SC/IR boundary shifts at both inter- and intra-specific levels. Our approach incorporated ITS, ITS1, ITS2, complete plastomes, matK, rbcL, and psbA-trnH sequences for molecular identification, which effectively differentiated the six medicinal species within the genus Amomum, as confirmed by distance-based and phylogenetic tree analyses. Among these, the ITS, ITS1, and complete plastomes sequences demonstrated the highest identification success rate (3/6), followed by ITS2, matK, and psbA-trnH (1/6). In contrast, rbcL failed to identify any species. This research successfully established a reliable molecular identification method for Amomum plants, to protect wild plant resources and promote the sustainable use of medicinal plants and restrict the exploitation of these resources.

We analyzed the plant-litter-soil continuum to investigate the carbon and nitrogen distribution and ecological stoichiometry of an evergreen broad-leaved forest at Dagangshan Mountain, Jiangxi. The results showed that the average C and N contents and C:N ratios in the leaves and fine roots among 6 different tree species were 401.87g/kg, 21.41g/kg, 19.27 and 348.64g/kg, 15.73g/kg, 23.97, respectively; the average C and N contents and C:N ratios were 323.06 g/kg, 12.76 g/kg, 25.58 respectively in leaf litter, and 16.40 g/kg, 1.09 g/kg, 16.27 respectively for soil. In contrast with the C content, the total N content of the fine roots and litter had a high coefficient of variation and a high spatial heterogeneity. We ranked the six different representative tree species according to total C and N content in leaves and fine roots. The results for each species were generally consistent with each other, showing a positive correlation relationship between total C and N content in the leaves and roots. Among them, S. discolor (Champ. ex Benth.) Muell. plants displayed high carbon and nitrogen storage capacities, and on the other hand, C. fargesii Franch., C. myrsinifolia (Blume) Oersted, A. fortunei (Hemsl.) Makino, and V. fordii (Hemsl.) Airy Shaw showed a high nitrogen transfer rate. Total soil N and C decreased with depth. Soil organic carbon (SOC), soil resistant organic carbon (ROC), total N, alkali nitrogen, NH4+-N and NO3--N contents were all also negative correlated with soil depth, but the contents of the NH4+-N and NO3--N did not change significantly; The spatial distribution of soil NO3--N was significantly heterogeneous. At 0-10 cm soil depth, SOC was positively correlated with alkaline nitrogen, and at 10-20 cm soil depth, SOC was significantly positively correlated with total N. In general, when soil carbon was abundant, nitrogen supply capacity was also high.

The gut microbiota plays a crucial role in childhood obesity, and diet is a dominating driver. The effects of fructo-oligosaccharides (FOS), as a dietary fiber, on the composition and metabolism of gut microbiota in healthy children was investigated by vitro fermentation system with a reformative YCFA medium (rich in tryptic hydrolysates of meat). The 16S rRNA sequencing technology was utilized to analyze the varieties of gut microbiota. Measurement of short chain fatty acids (SCFAs) and gases were used by the gas chromatograph. Majorbio Cloud Platform and MetOrigin, as the interactive cloud server, perform the microbiota analysis, the metabolic pathway enrichment analysis, the statistical correlations, and biological relationships using network visualization. We found that the FOS group significantly regulated the composition and metabolism of gut microbiota. The co-metabolism network showed that 3 metabolites were related to 6 differential bacteria and 8 metabolism pathways. These findings suggest that dietary fiber could regulate the composition of gut microbiota and its metabolites in a better direction, but when dietary fiber participates in precision nutrition formula, it may be relevant for precision obesity, may help identify windows of opportunity for the dietary intervention of childhood obesity.

SARS-CoV-2, influenza A/B virus (IAV/IBV) and respiratory syncytial virus (RSV) are among the common viruses causing acute respiratory infections. Clinical diagnosis to differentiate these viruses is challenging due to similar clinical presentations, thus laboratory-based real-time RT PCR is the gold standard for diagnosis. The study aimed to evaluate the diagnostic performance of STANDARD M10 Flu/RSV/SARS-CoV-2 (SD Biosensor Inc, Seoul, Korea). This retrospective study was conducted with archived respiratory samples positive and negative for SARS-CoV-2, IAV, IBV or RSV. The evaluation study involved a total of 322 respiratory samples comprising 215 positive samples (49 SARS-CoV-2, 48 IAV, 53 IBV, 65 RSV) and 107 negative samples. All samples were tested with both STANDARD M10 and either Xpert Xpress SARS-CoV-2 or Xpert Xpress Flu/RSV (Cepheid, USA). The sensitivity, specificity, positive predictive value and negative predictive value rates of STANDARD M10 were very similar to Xpert Xpress SARS-CoV-2 or Xpert Xpress Flu/RSV ranges for each virus (98-100%). The overall agreement was 99.4% with 99.1% agreement for positive samples and 100% agreement for negative samples. In conclusion, the STANDARD M10 point-of-care test is suitable for rapid simultaneous detection of SARS-CoV-2, IAV, IBV and RSV.

This paper proposes an approach for image data extraction and driving behavior analysis using geographic information and driving data. Information derived from geographic and global positioning systems was used for image data extraction. In addition, we used an onboard diagnostic II and a controller area network bus logger to record driving data for driving behavior analysis. Driving behavior was analyzed using sparse automatic encoders and data exploration to detect abnormal and aggressive behavior. A regression analysis was used to derive the relationship between aggressive driving behavior and road facilities. Several traffic improvements were proposed for specific intersections and roads. The results indicate that lane ratios without lane markings and with straight lane markings are important features that affect aggressive driving behaviors.

Fruit cracking or splitting, a severe physiological disease that highly affects appearance and quality, compromise the commodity value of fruit and also causes huge economical losses to the producers of several fleshy fruit crops. The growth-promoting phytohormone gibberellic acid (GA) and growth-inhibiting phytohormone abscisic acid (ABA) antagonistically regulate numerous developmental processes throughout the plant life cycle. Homeostasis of endogenous GA and ABA play a significant role in the normal growth of fruits, and its imbalance may lead to the occurrence of cracking or splitting during the process of fruit growth, development, ripening and postharvest storage. The pathways of GA and ABA metabolism and signaling have been studied widely, and the major components were well characterized, which including the genes encoding major biosynthesis and catabolism enzymes and the key signaling components. Nevertheless, our knowledge of the mechanisms of GA and ABA governing fruit cracking is not comprehensive enough. In this review, we not only focus on the scenarios of effects of endogenous GA and ABA contents in the fruit and exogenous plant growth regulators GA and ABA treatments, but also endeavor to provide some genetic cues on the function of GA and ABA responsible for fruit cracking modulation. Information from this review aims to strengthen the understanding of potential molecular bases underlying GA and ABA in fruit cracking control and provide guidance in breeding of fruit cultivars with cracking-resistant ideotypes, and also make great theoretical significance in guiding the establishment of integrated prevention and control measures to fruit cracking or splitting.

Remote sensing image registration plays an important role in military and civilian fields, such as natural disaster damage assessment, military damage assessment and ground targets identification, etc. However, due to the ground relief variations and imaging viewpoint changes, non-rigid geometric distortion occurs between remote sensing images with different viewpoint, which further increases the difficulty of remote sensing image registration. To address the problem, we propose a multi-viewpoint remote sensing image registration method which contains the following contributions. (i) A multiple features based finite mixture model is constructed for dealing with different types of image features. (ii) Three features are combined and substituted into the mixture model to form a feature complementation, i.e., the Euclidean distance and shape context are used to measure the similarity of geometric structure, and the SIFT (scale-invariant feature transform) distance which is endowed with the intensity information is used to measure the scale space extrema. (iii) To prevent the ill-posed problem, a geometric constraint term is introduced into the L2E-based energy function for better behaving the non-rigid transformation. We evaluated the performances of the proposed method by three series of remote sensing images obtained from the unmanned aerial vehicle (UAV) and Google Earth, and compared with five state-of-the-art methods where our method shows the best alignments in most cases.

This study is a two-phase hybrid study on the behavioral activities of undergraduate students during the COVID-19 pandemic lockdown. A questionnaire survey of students during the whole school period and a semistructured interviews with 13 undergraduates of different majors were conducted. First, we found that compared with primary and secondary school students, undergraduates showed many problems with self-time management. Second, the behavior of undergraduates at home may result from multiple factors, such as past experience, professional identity and behavioral habits. When secondary school provided a relatively relaxed learning environment or secondary school teachers placed more emphasis on continuous effort, and when students had a strong sense of the social value of their undergraduate major, students worked harder and achieved more during the pandemic. Otherwise, it was easier for students to slack off and be passive during the pandemic. Altogether, this study deepens our understanding of undergraduates' self-management of free time, and the differences in the values underlying different behaviors and the formation process of various behaviors.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

Against the backdrop of the current carbon peaking and carbon neutrality policies, higher requirements have been put forward for the upgrading and construction of smart grids. Non-intrusive load monitoring (NILM) technology is a key technology for advanced measurement systems at the end of the power grid. It obtains detailed power information of the load, without the need for traditional hardware deployment. The key step to solve this problem is load decomposition and identification. This paper first utilized Long Short Term Memory-Denoising Autoencoder(LSTM-DAE) to decompose the mixed current signal on the household busbar and obtain the current signals of multiple independent loads that constituted the mixed current. Then, the obtained independent current signals were combined with voltage signals to generate multi-cycle colored Voltage-Current(VI) trajectories, which were color-coded according to the background. These colored VI trajectories with background colors formed a feature library. When the CNN network was used for load recognition, considering the influence of hyperparameters on recognition results, the BOA algorithm was used for optimization, and the optimized CNN network was employed for VI trajectory recognition. Finally, the proposed method was validated using the PLAID dataset. Experimental results showed that the proposed method exhibited better performance in load decomposition and identification.

The low and unstable performance is still one of the major obstacles for anaerobic digestion, which provokes researchers to develop some strategies to improve it. In addition to traditional approaches such as co-digestion, pretreatment, and recirculation, some emerging strategies, namely additive and microaeration have also been recognized and developed in recent years due to the update of knowledge. Many studies have evaluated the effect of those strategies on digestion performance. However, it lacks a unified analysis and induction, especially the mechanism for different strategies. Therefore, this review presents a comprehensive view of research progress on the strategies based on latest researches considering five main strategies. Critical think and summary of their mechanism, reactor performance, and availability of those strategies were executed. The results demonstrated that the contribution of microaeration is mainly to balance the composition and activity of hydrolysis, acidogenesis, and methanogenic archaea. Recirculation and co-digestion balance mass and reaction environments. Pretreatment makes the structure of the substrate (such as removing lignin, reducing cellulose crystallinity, and increasing the substrate-specific surface area) more conducive to microbial utilization. The mechanism of the additive strategy varies greatly depending on the type of additive, such as enhancing interspecies electrons transfer through conductive materials, resisting adverse digestion conditions through functional microbial additives, and accelerating nutrient absorption by regulating the bioavailability of trace elements. Although these strategies have different mechanisms for promoting digestion performance, their ultimate goal is to make the parameters of the reactor to an ideal status, and then to achieve a balance among substance, microorganisms and water in anaerobic reactor.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Accurate lithium battery diagnosis and prognosis is critical to increase penetration of electric vehicles and grid-tied storage systems. They are both complex due to the intricate, nonlinear, and path-dependent nature of battery degradation. Data-driven models are anticipated to play a significant role in the behavioral prediction of dynamical systems such as batteries. However, they are often limited by the amount of training data available. In this work, we generated the first big data comprehensive synthetic datasets to train diagnosis and prognosis algorithms. The proof-of-concept datasets are over three orders of magnitude larger than what is currently available in the literature. With benchmark datasets, results from different studies could be easily equated, and the performance of different algorithms can be compared, enhanced, and analyzed extensively. This will expend critical capabilities of current AI algorithms, tools, and techniques to predict scientific data.

Li₂MnO₃ is critical component in the well-studied Li-excess cathode materials xLi₂MnO₃•(1- x)LiMO₂ for achieving high lithium storage capacity. In this article, the diffusion of Li ions in Li₂MnO₃ is studied using molecular dynamics (MD) simulation with well-behaved empirical force fields obtained by fitting against the crystal structure from experiment and phonons calculated using Density Function Theory (DFT). We have found two possible tetrahedral hopping channels, 0-TM and 1-TM(Mn⁴⁺) channel, which are differentiated by the face sharing octahedral cations. Simulation results show that the 0-TM channel is active for Li hopping, while 1-TM(Mn4+) channel is inactive. During the delithiation process, the Li ions in the TM layered are firstly removed, then those in the Li layer. However, the Li ions will be trapped in the tetrahedral 0-TM channels as long as the four face sharing octahedral sites are cleared. Up to x=1.0 for Li₂-xMnO₃, almost all the Li ions are located at the tetrahedral sites, forming a regular array along a axis. The de-intercalation of tetrahedral Li ions requires a high voltage (>5.2 V vs. Li/Li+), limiting the practical capacities measured in lab. The diffusion of Mn ions into the Li layers is observed in a deeper delithiated structure (x=1.2 for Li₂-xMnO₃), indicating an initial phase transformation to a spinel-like structure. However, the Mn ions are mainly trapped in the tetrahedral sites in the Li layer, instead of the octahedral sites fin spinel-like structure. A few of Mn ions diffusing into the octahedral sites in Li layers have no face sharing tetrahedral Li ions, revealing a further Li de-intercalation is imperative for the complete phase transformation. Our model is not stable for x≥1.4 in Li₂-xMnO₃. Other charge compensation mechanism should be considered in this high delithiation stage, eg. oxygen release.

This study presents an instant preview and analysis system implementation of intelligent stereo cameras (ISCs). A parameter optimization prototype adopted the instant preview and analysis system of the ISCs has been achieved the automatic alignment function, and obtained optimal stereo films with the automatic alignment function by adjusting gap and angle between dual cameras. The instant preview and analysis system of the ISCs with parameter optimization can enhance the quality of stereo films effectively and reduce filmed errors and save retouched cost and time in harsh filmed environment.

The negative impact of the modern-day lifestyle on the environment is aggravated during the COVID-19 pandemic through the increased use of single-use plastics from food takeaways to medical supplies. Similarly, the closure of food outlets and disrupted supply chains have also resulted in significant food wastage. As the pandemic rages on, the aggravation of increased waste becomes an increasingly urgent problem that threatens the biodiversity, ecosystems, and human health worldwide through pollution. While there are existing methods to deal with the organic and plastic waste, many of the solutions also cause additional problems. Increasingly proposed as a natural solution to man-made unnatural problems, there are insect solutions for dealing with the artificial and organic waste products towards a circular economy, making the use of natural insect solutions commercially sustainable. This review discusses the findings and how some of these insects, particularly the Hermetia illucens, Tenebrio molitor, and Zophobas morio, can play an increasing important role in food and plastics, with a focus on the latter.

Supramolecular solvent (SUPRAS) has received increasing interest as an innovative, efficient, and green solvent for the effective extraction and separation of bioactive compounds from natural resources. However, studies on the use of SUPRAS for the extraction of phenolic components from plants, which are highly valued in food products due to their excellent antioxidant capacity, are still lacking. The present study developed a green ultrasound-assisted and efficient SU-PRAS method to simultaneously determine three phenolic acids in Prunella vulgaris by high-performance liquid chromatography (HPLC) and the experimental parameters were optimized in detail. The efficiency and antioxidant properties of the phenolic compounds obtained by different extraction methods were also compared. Under the optimal conditions, the extraction efficiency of SUPRAS, prepared with octanoic acid reverse micelles dispersed in ethanol-water, was substantially higher than conventional organic reagents. Moreover, this SUPRAS method also showed more significant antioxidant capacities. The confocal laser scanning microscopy (CLSM) images presented the spherical droplet structure of SUPRAS (A well-defined circle), which coincided with the position of the fluorescence position of phenolic acids. The phenolic acids were encapsulated in the vesicles by the SUPRAS droplets, which indicated the efficient extraction capacities of SUPRAS for the target compounds. Finally, combined with the CLSM method, the mechanism of the proposed method was further clarified, and the superior extraction performance of SUPRAS was theoretically demonstrated through molecular dynamics simulations. In comparison with conventional methods, the higher extraction efficiency of SUPRAS can be illustrated by the larger solvent contact surface area, more types of hydrogen bonds between extractants and supramolecular solvents, and stronger and more stable interaction forces. The results of the theoretical studies are in rational agreement with the experimental outcome.

Dredging is a common technique for managing eutrophication problems in waters, reducing the accumulation of pollutants by removing sediments from the bottom of water bodies. However, dredging can cause complex impacts on lake ecosystems, and it is crucial to understand benefits and mechanisms for environments. In this paper, the dredged and undredged areas in the Caohai portion of Dianchi Lake were studied to analyze the effects of dredging on nitrogen-phosphorus transport and conversion and changes in nitrogen-phosphorus morphology content and its mechanisms by comparing the nitrogen-phosphorus morphology content, percentage; nitro-gen-phosphorus ratio, and release contribution of the two areas. It was found that the ratio of sta-bilized nitrogen (SN) to stabilized phosphorus (SP) in the dredged area was lower than that in the non-dredged area; the BD-P and TOC contents had a large turnaround at the 16-20 cm position of the sediment in the dredged area; and the main conclusions were that the dredging would disrupt the internal equilibrium of the lake system for many years, and in particular, it would have the greatest effect on the balance of the BD-P in the phosphorus forms of the sediment, and that the column cores of the dredged area from 0 to 16 cm might be newly accumulated sediments after the dredging project. However, with time, the distribution of nitrogen and phosphorus forms in the newly accumulated sediments will gradually reach a new equilibrium. In addition, dredging will also cause significant changes in the retention efficiency of nitrogen and phosphorus in the sediment, and the stable nitrogen and phosphorus forms will be released and transformed into unstable ni-trogen and phosphorus forms.

The aim of this paper is to use deep learning tools to innovate pre-trained object detection models to improve the accuracy of non-destructive testing (NDT) of civil aviation maintenance. First, this thesis classifies object defects for NDT, such as cracks, undercut, etc. Nowadays, thesis surveys innovation deep-learning methods technology is used to improve the defect detection performance inferencing capability, increase the accuracy and efficiency of automatic identification which in enhanced the safety and reliability of aircraft fuselage in future, mark hidden cracks and solve the challenges that cannot be identified by manual inspection. Second, recent mainstream techniques the YOLOv4 neural network to the graphics card GPU core operator to speed up the recognition of defect images is being applied to the non-destructive inspection process of aircraft maintenance on A, C and D-Level, fully validating the deep learning model's powerful defect detection target capability. The attention-based YOLOv4 algorithm is improved by applying a one-stage attention mechanism to the YOLOv4, thereby improving the accuracy of the innovation model. Finally, thesis improved YOLOv4 based on an attention mechanism is proposed for object detection NDT via the deep learning method to effectively improve and shorten the inspection anomaly detection method for automatic detection sensor systems.

To ensure the safety in aircraft flying, we aim use of the deep learning methods of nondestructive examination with multiple defect detection paradigms for X-ray image detection posed. The use of the Fast Region-based Convolutional Neural Networks (Fast R-CNN) driven model seeks to augment and improve existing automated Non-Destructive Testing (NDT) diagnosis. Within the context of X-ray screening, limited numbers insufficient types of X-ray aeronautics engine defect data samples can thus pose another problem in training model tackling multiple detections perform accuracy. To overcome this issue, we employ a deep learning paradigm of transfer learning tackling both single and multiple detection. Overall the achieve result get more then 90% accuracy based on the AE-RTISNet retrained with 8 types of defect detection. Caffe structure software to make networks tracking detection over multiples Fast R-CNN. We consider the AE-RTISNet provide best results to the more traditional multiple Fast R-CNN approaches simpler translate to C++ code and installed in the Jetson™ TX2 embedded computer. With the use of LMDB format, all images using input images of size 640 × 480 pixel. The results scope achieves 0.9 mean average precision (mAP) on 8 types of material defect classifiers problem and requires approximately 100 microseconds.

The design, facilities and conditions inside a classroom play a significant role in the teaching and learning experience for both students and lecturers. Prior studies of primary schoolchildren indicate three design principles affecting student learning, namely: naturalness, individualisation and stimulation. The current study extends these investigations to Higher Education through a survey of undergraduate students and university lecturers aimed at determining the most critical factors in undergraduate classroom design. One-to-one interviews were conducted with students and lecturers (n. 31) at the University of Nottingham, Malaysia Campus. Interviewees were encouraged to express their opinions, comments, concerns and suggestions through open-ended questions. The interviews were recorded and then transcribed and coded using NVivo10. Results show a strong desire among lecturers and students for improved classroom equipment, greater flexibility in classroom arrangement, more attractive decoration and for the addition of natural elements to the classroom environment. Of the three design principles, individualisation and naturalness emerged most strongly from the interviews and appear to be more important factors for undergraduates than stimulation. These findings could make a novel and significant contribution to the physical aspects of classroom design in Higher Education settings. Educational institutions are increasingly employing non-traditional classroom designs, which are expected to provide for more flexible, collaborative, and active learning and teaching experiences. Taking into consideration the environmental psychology of teaching and learning, several of the reported design attributes can serve as benchmarks for upgrading current classroom design and facilities in the future, as institutions look to upgrade their physical infrastructures to meet the changing demands of teachers and learners arising from technological innovations and shifts in our understanding of the methods and purposes of Higher Education.

This study chose the indoor soil column test as the main method and the field test as the validation test to investigate the effects of various straw mulching techniques (surface, deep and straw mulching + deep burial) on evaporation and salt dynamics in saline soils. The results showed that straw mulching treatment could effectively reduce soil water evaporation, promote desalination in the stage of leaching infiltration and alleviate salt return in the stage of water evaporation, and the effect of straw mulching + deep burial treatment was better than that of single-layer straw mulching treatment. The indoor soil column test showed that S2D1 treatment (a 2:1 ratio of soil surface cover to the amount of straw buried 40cm below the soil surface) had the best effect on the suppression of soil moisture evaporation, and the cumulative evaporation of soil moisture was reduced by 65.85% compared with that of the CK, and the rate of salinity return in the evaporation stage was effectively reduced by 92.04% compared with that of the CK. In addition, there is a significant positive correlation between cumulative evaporation of soil moisture and cumulative soil salinity, which implies that cumulative soil salinity increases with cu-mulative evaporation of soil moisture. The results of the field experiment were consistent with the soil column test, and the S2D1 treatment was able to maintain high soil moisture content in all soil layers in all periods of the experiment and kept soil salinity in the 0-40 cm soil layer at a low level. However, in the 40-80 cm soil layer, the soil salinity suppression effect of DB treatment (straw buried at 40 cm below soil surface) was the best. So in summary, the S2D1 treatment had the best salinity and evapo-transpiration suppression effect in saline soils. This study is of great significance for the resource uti-lization of straw waste, improvement of water utilization and efficiency, and soil salinization manage-ment.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

Molecular dynamics (MD) simulations present a sophisticated nano-scale computational approach that can play a critical role in material design for next generation batteries. One critical piece of information needed for MD simulations is the non-bonded potential parameters, which can be obtained through quantum mechanics (QM) calculations or experimental methods. However, experimental data is not available for exploratory and novel materials to derive the potential parameters. Also, the QM approach needs significant computational power and is too time consuming for large systems. On the other hand, current Artificial Intelligence techniques are faster, but they cannot be generalized across molecules and properties. As a result, there is a significant barrier to discovering and exploring new materials. Overcoming this barrier, in this work, we propose a Machine Learning (ML) based technique that can learn inter-atomic potential parameters for various particle-particle interactions employing QM calculations. This ML model can be used as an alternative for QM calculations for predicting non-bonded interactions in a computationally efficient manner. Using these parameters as input to MD simulations, we can predict a diverse range of properties, enabling researchers to design new and novel materials suitable for various applications in the absence of experimental data. We employ our ML-based technique to learn the Buckingham potential, a non-bonded interatomic potential. Subsequently, we utilize these predicted values to compute the densities of four distinct molecules, achieving an accuracy exceeding 93%. This serves as a strong demonstration of the efficacy of our proposed approach.

The COVID-19 pandemic caused by the novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) virus has exposed the vulnerabilities and unpreparedness of the global healthcare system in dealing with emerging zoonoses. In the past two decades, coronaviruses (CoV) have been responsible for three major viral outbreaks, and the likelihood of future outbreaks caused by these viruses is high and nearly inevitable. Therefore, effective prophylactic universal vaccines targeting multiple circulating and emerging coronavirus strains are warranted. This study utilized an immunoinformatic approach to identify evolutionarily conserved CD4+ (HTL) and CD8+ (CTL) T cells, and B-cell epitopes in the coronaviral spike (S) glycoprotein. A total of 132 epitopes were identified, with the majority of them found conserved in the bat CoV, pangolins CoV, endemic coronaviruses, SARS-CoV-2, and Middle East respiratory syndrome coronavirus (MERS-CoV). Their peptide sequences were then aligned and assembled to identify the overlapping regions. Eventually, two major peptide assemblies were derived based on their promising immune-stimulating properties. In this light, they can serve as lead candidates for universal coronavirus vaccine development, particularly in the search for pan-coronavirus multi-epitope universal vaccines that can confer protection against current and novel coronaviruses.

Food-grinding occurs in rodents and is influenced by multiple-factors. However, the factors affecting this behavior remain unclear. In this study, we aimed to investigate the effect of food restriction on food grinding by Brandt’s voles (Lasiopodomys brandtii), as well as the potential role of the gut microbiota in this process, through a comparison of the variations between voles with different food supplies. Food restriction reduced the relative amount of ground food to a greater extent than it lowered the relative food consumption, and altered the abundance of Staphylococcus, Aerococcus, Jeotgalicoccus, and Un--s-Clostridiaceae bacterium GM1. Strong correlations between the ground-to-consumed food ratio and the abundance of fecal microbiota were found for Un--s-Clostridiaceae bacterium GM1 and Aerococcus. The content of fecal acetate and propionate for the 7.5 g-food supply group was lower than that for the 15 g-food supply group. Further, the relative amount of ground food and ground-to-consumed food ratio were both positively correlated with the acetate content. Our study indicated that food restriction can effectively inhibit food grinding. Further, Un--s-Clostridiaceae bacterium GM1 abundance, Aerococcus abundance, and acetate content were strongly related to food grinding. Variations in gut microbial abundance and metabolite short-chain fatty acid content induced by food restriction likely promote the inhibition of food grinding. These results could potentially provide guidance for reducing food waste during laboratory rodent maintenance.

Dryland winter wheat in Loess Plateau is facing yield reduction due to shortage of soil moisture and delayed sowing time. Field experiment was conducted at Loess Plateau in Shanxi Province, China from 2012 to 2014, to study the effect of subsoiling and conventional tillage and different sowing dates on the soil water storage and contribution of N accumulation and remobilization to yield of winter wheat. The results showed that subsoiling significantly improved the soil water storage at 0-300 cm depth, improved the number of tillers and pre-anthesis N translocation in various organs of wheat and post-anthesis N accumulation, eventually increased the yield up to 17-36%. Delaying sowing time had reduced the soil water storage at sowing and winter accumulated temperature by about 180˚C. The contribution of N translocation to grain yield was maximum in glume+spike followed by in leaves and minimum by stem+sheath. In addition a close relationship was found between the N accumulation and translocation and the soil moisture in the 20-300 cm. Subsoiling during the fallow period and the medium sowing date was beneficial for improving the soil water storage and increased the N translocation to grain, thereby increasing the yield of wheat, especially in dry year.

Climate change poses a serious threat to the ancient Magnoliaceae family, particularly for the endangered Yulania trees. Until now, little is known about the suitable geographical range of Yulania zenii, and about how it responds to past and future climate scenarios. Here, we first employed ten models from Biomod2 to preliminarily simulate its potential distribution in China and selected MaxEnt for final modeling. The results showed that among the key environmental factors influencing its distribution, the top three factors were Bio2 (Mean diurnal range), Bio15 (Precipitation seasonality of variation coefficient) and Elevation. Its current suitable distribution were primarily concentrated in southern Anhui, central Hubei, eastern Hunan, southern Jiangsu, northern Jiangxi, and northern Zhejiang. The total suitable area of Yulania zenii was 14.68 × 104 km2, only taking 1.53% of China's total territory, which is larger than known. During the Last Interglacial and Middle Holocene, its suitable habitats were larger than currently, exhibiting a relatively continuous distribution. Under various future climate scenarios, its suitable habitats may averagely decrease by 20.26% compared with the current, and these habitats become more fragmented. Collectively, the centroid of Yulania zenii is expected to migrate towards the southeast in the future. Therefore, our findings demonstrate, for the first time, that climate change takes an adverse effect on this species in distribution from the past to current till future. Our study can contribute to the conservation and management of Yulania zenii in China, and can provide reference for other endangered Yulania species of this country under the condition of climate change.

Plant Cysteine Oxidase (PCO) is a plant O2-sensing enzyme of catalyzing oxidation of cysteine to Cys-sulfinic acid at the N-termini of target proteins. To better understand the Brassica napus PCO gene family, PCO genes in B. napus and related species were analyzed. In this study, 20, 7 and 8 PCO genes were identified in Brassica napus, Brassica rapa and Brassica oleracea, respectively. According to phylogenetic analysis, the PCOs were divided into five groups: PCO1, PCO2, PCO3, PCO4 and PCO5. Gene organization and motif distribution analysis suggested that PCO gene family was relatively conserved during evolution. Expression analysis showed that PCO genes were expressed in different tissues at different developmental stages. Interestingly, most of the Bna/Br/BoPCO5 members were expressed in leaves, roots, flowers, buds and siliques, suggesting an important role in both vegetative and reproductive development. Expression of BnaPCO was induced by various abiotic stress, especially waterlogging stress, which was consistent with the result of cis-element analysis. In this study, the PCO gene family of Brassicaceae was analyzed for the first time, which contributes to a comprehensive understanding of the origin and evolution of PCO genes in Brassicaceae and the function of BnaPCO in regulating plant responses to abiotic stresses.