Flexible capacity applications demands to large energy storage density and high breakdown electric field strength of flexible films. Here, P(VDF-HFP) with ultra-thin Al2O3 nanosheets composite films were designed and fabricated through an electrospinning process followed by hot-pressing in sandwich structured. The results show that the insulating ultra-thin Al2O3 nanosheets and the sandwich structure can enhance the composites' breakdown field (by 24.8%) and energy density (by 30.6%) remarkedly to P(VDF-HFP) polymer matrix. An energy density of 23.5 J/cm3 at the ultrahigh breakdown field of 740kV/mm can be therefore realized. Insulating test and phase-field simulation results reveal that ultra-thin nanosheets insulating buffer layers can reduce the leakage current in composites, thus it effects the electric field spatial distribution to enhance breakdown strength. Our research provides a feasible method to increase the breakdown strength of ferroelectric polymers, which is comparable to those of non-ferroelectric polymers.

Abstract:The ecological protection of cultivated land is crucial for advancing high-quality agricultural development. This study analyzes the impact of agricultural socialization services on the ecological conservation of farmland, focusing on the reduction of chemical fertilizers and pesticides among rice farmers in the Jianghan Plain area. Utilizing data from 743 farmer household surveys conducted in 2023, the findings reveal that agricultural socialization services significantly encourage farmers to reduce chemical input usage. Specifically, a 1% increase in the level of agricultural socialization services correlates with a 14% decrease in chemical fertilizers and a 16.4% decrease in pesticides per mu. The study identifies scale operation, factor substitution, and alleviation of capital constraints as mediating factors enhancing the efficacy of these services. Furthermore, heterogeneity analysis indicates that these services are more effective in reducing chemical inputs among large-scale and newer-generation farmers compared to their small-scale and older counterparts. Additionally, technology-intensive socialized services exhibit a stronger impact on reducing chemical inputs than labor-intensive services.

The western Sulige gas field is a new and key reserve area for the rolling development of the Sulige gas field in China. However, due to the complex gas–water relationship and the difficulty in identifying gas and water formation, the scale and benefit deployment of the gas field are seriously restricted. In particular, almost all of the wells in the area produce water and no water measurement has been carried out for any single well, which leads to an unclear understanding of the dynamic characteristics of the production wells, thus affecting the productivity calculations of the gas wells and the overall regional productivity evaluation. Based on the testing data for a gas well, the impacts of the reservoir property parameters on the gas and water production were analyzed by combining the production performance and static geological characteristics. It was determined that the physical parameters K, Kh, and φSg had good positive correlations with gas production but not with water production; thus, effective prediction cannot be obtained for water production in gas well testing. After the analysis of the liquid loading law, the gas wells were classified into three types: continuous liquid carrying production, slight liquid loading, and liquid loading wells. In general, up to 96% of the gas wells were liquid loaded. According to the different production performances exhibited in the different stages of the gas wells, five types of methods for diagnosing water production wells were proposed (gas testing, pilot production, gas–liquid two-phase measurement testing, liquid level detection, and production performance analysis), as well as the diagnostic criteria and corresponding solutions. To obtain real-time water production data for each well and investigate the change of water-gas ratio (WGR) during the whole production process, a water production splitting method for gas wells based on three-dimensional geological modeling and numerical simulation combined with the constraints of the total water production of gas gathering stations was explored and established. The splitting results can be used to evaluate the water and gas productivity of gas wells and determine the best deliquification period. The gas well productivity when water production was considered was about 10% lower than that when water production was not considered. The best deliquification period was determined to be 125 days for wells with small water production, 20 days for wells with moderate water production, and 3 days for wells with serious water production. The results of this study could provide technical support for the scientific evaluation of gas well production indicators, reduction of development costs, and improvement of oil recovery.

Tilapia lake virus (TiLV) is the main tilapia-infecting virus worldwide, causing serious economic losses. However, there is no vaccine for this viral disease. Here, TiLV ORF10 (TiLV-ORF10) encoding a protein with abundant epitopes was constructed into the eukaryotic expression vector pcDNA3.1, and used to evaluate the immune protective effects in Nile tilapia (Oreochromis niloticus). RT-PCR and western blot analyses confirmed vaccine plasmid expression in tilapia muscle tissues. Moreover, the transcription levels of immunoglobulin M, toll-like receptor 2, myeloid differentiation factor 88, interleukin 8, tumor necrosis factor alpha, gamma-IFN, and nuclear factor κB immune-related genes were statistically significantly upregulated in the spleen, liver, and kidney of vaccinated tilapias (P < 0.05). TiLV challenge experiments showed that relative percent survival (RPS) was significantly enhanced in fish by this DNA vaccine. Moreover, RPS was enhanced further when using a higher amount of the DNA vaccine (85.72% RPS at a DNA dose of 45 μg pcDNA3.1–ORF10). Vaccination with pcDNA3.1–ORF10 significantly reduced virus replication, as evidenced by the low amount of virus in the spleen, liver, and kidney of vaccinated tilapias after TiLV challenge. Thus, pcDNA3.1–ORF10 could induce protective immunity in tilapia and may be a potential vaccine candidate for controlling diseases caused by TiLV.

Two-dimensional (2D) of transition metal dichalcogenides (TMDCs) are potential candidates for thermoelectric (TE) applications due to their unique structural properties. In this paper, we constructed an 2D monolayer TMDCs semiconductor γ-PbSn2(X=S, Se, Te) and first-principles calculations and Boltzmann transport theory are used to study the thermoelectric performance. We found that γ-PbSnX2 had an ultra-high carrier mobility up to 4.04×103 cm2V−1s−1 leading to a metal-like electrical conductivity. Meanwhile, γ-PbSnX2 both have high Seebeck coefficients, resulting in high power-factors, and also shows intrinsic low lattice thermal conductivity of 6-8 W/mK at room temperature. The lower lattice thermal conductivity and high power-factors resulted in excellent thermoelectric performance. The high ZT values of γ-PbSnS2 and γ-PbSnSe2 were as high as 2.65 and 2.96 at 900 K, respectively. The result suggests that the monolayer γ-PbSnX2 are better candidates for excellent thermoelectric performance.

In this work, we proposed a novel design of microfluidic mixer utilizing the amplified Marangoni chaotic advection induced by AC continuous electrowetting of a metal droplet situated in electrolyte solution, due to the linear and quadratic voltage-dependence of flow velocity at small or large voltages, respectively. Unlike previous researchers exploiting the unidirectional surface stress with DC bias at droplet/medium interface for pumping of electrolyte where the resulting flow rate is linearly proportional to the field intensity, dominance of another kind of dipolar flow pattern caused by local Marangoni stress at the drop surface in sufficiently intense AC electric field is demonstrated by both theoretical analysis and experimental observation, which exhibits a quadratic growth trend as a function of the applied voltage. The dipolar shear stress merely appears at larger voltages and greatly enhances the mixing performance by inducing chaotic advection between the neighboring laminar flow. The mixer design developed herein, on the basis of amplified Marangoni chaotic advection around a liquid metal droplet at larger AC voltages, has great potential for chemical reaction and MEMS actuator applications, because of generating high-throughput and excellent mixing performance at the same time.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

To expand the application area of the reference group and enrich exercise theoretical research, based on Stimulus-Organism-Response (S–O-R) framework, this study examines the factors that motivate for adherence to exercise from the external. Taking reference group and strategy and cultural fit as the main stimulus, and personal investment and life satisfaction as mediating variables, this study try to explore the influence of external stimulus on residents’ exercise behavior. In order to enrich the sample size, two surveys of 734 Chinese residents in two cities (Xiamen vs. Fuzhou) were conducted using factor analyses, regression analysis, and T-test analysis. The results indicated that the reference group and strategic and cultural fit as external stimulus have impact on residents’personal investment, life satisfaction and exercise adherence, personal investment and life satisfaction as the organism has impact on residents’ exercise adherence. Personal investment and life satisfaction play a chain mediating role between the reference group and exercise adherence, strategy and cultural fit, and exercise adherence. Moreover, the T-test determined the differences between Xiamen and Fuzhou residents’ exercise adherence and life satisfaction. Residents’ surroundings affect their exercise behavior and life satisfaction. These findings have implications for policymaking aimed at promoting national exercise, which could gradually improve residents’ physical fitness, particularly in light of the current coronavirus emergency.

The ergosterol pathway is a prime antifungal target. The minimum inhibitory concentration (MIC) assay is a simple research tool that determines the lowest concentration at which a novel antimicrobial with limited scope to determine the mechanism of action for a drug. In this study, we show that by adding hydrogen peroxide, an oxidative stressor, or glutathione (GSH), an antioxidant, to modify a commonly performed MIC assay allowed us to screen selectively for new antifungal drugs that target ergosterol biosynthesis in fungi. A human pathogen, Microsporum gypseum, was used as a test organism. When exposed to ergosterol targeting drugs, the hydrogen peroxide treatment significantly decreased fungal survival by reducing ergosterol in the cell wall, whereas GSH increased survival of M. gypseum. Further, by performing a series of experiments with M. gypseum, it was determined that the oxidative stress from hydrogen peroxide causes cell death at different developmental stages. These findings allow us to describe a simple, high-throughput method for simultaneously screening new antifungal drugs for activity and effects on the ergosterol pathway. By using this tool, two isoquinoline alkaloids were discovered to be potent inhibitors of ergosterol biosynthesis by reducing the amount of ergosterol without affecting the expression of 1,3-β-glucan.

Nutrients are the driving force of plant and herbivore interactions. Different elements and fertilization levels in soil, or artificially fertilized substrates can have a direct impact on plant defense responses. Meanwhile, nutrient levels mediated by root associated microbes can indirectly affect plant-herbivore interactions. Nutrient uptake promoted by beneficial mycorrhizal fungi or rhizobacteria interacting with roots can stimulate plant tolerance to herbivore attack, as evidenced by herbivore performance, plant nutrient status, plant biomass allocation and compensatory growth. In return, herbivory affects nutrient fluxes between plants and their associated beneficial microbes. Furthermore, aboveground and belowground herbivory can affect the nutrient exchange between plants and soil microbial communities, mainly for carbon-and nitrogen-based resources supporting herbivores´ life cycles. These ecological interactions are governed by jasmonic acid (JA) and key enzymes on the molecular level. This review summarizes the current scientific literature on the role of nutrients in plant-herbivore interactions. This will support efforts to optimize plant defense strategy via managing nutrient variance.

Fire is a serious security threat that can lead to casualties, property damage, and environmental damage. However, despite the availability of object detection algorithms, challenges persist in detecting fires and smoke. These challenges include slow convergence speed, poor performance in detecting small targets, and high computational cost limiting deployments. In this paper, Fire smoke and human detection based on ConvNeXt and Mixed encoder (FCM-DETR), an end-to-end object detection algorithm based on Deformable DETR, is proposed. Firstly, we introduce ConvNeXt to take the place of Resnet, which greatly reduces the amount of computation and improves the ability to extract irregular flame features. Secondly, to effectively process multi-scale features, the original encoder is decoupled into two modules. Then Mixed encoder, an innovative encoder structure, is proposed, resulting in excellent performance of multi-scale fire and smoke features fusion. What can’t be overlooked is that the encoder block is compatible with any DETR-based models. Finally, the convergence speed is accelerated and the mean of average precision is improved by applying a novel loss function called Powerful IoU v2. The experimental results indicate that our model achieves the best detection accuracy compared to other models, with mAP reaching 66.7%, mAPs and Accuracyfire achieving impressive 50.2% and 98.05%, respectively.

This article analyzes in detail the influence of Jupiter on the measurement of the gravitational constant. Including a specific estimate of the change in the gravitational constant caused by the change of the earth's orbital position every half month. The influence of Jupiter's perihelion and aphelion on the gravitational constant is also estimated. On this basis, this article analyzes the data with specific time records such as BIPM-01, BIPM-14, JILA-10, UCI-14, HUST-09. The analysis results show that after considering the influence of Jupiter, the experimental results have been significantly improved.

This paper investigates the hydroelastic responses of offshore floating solar photovoltaic farms (OFPVs) to minimize structural motion. The OFPV usually occupies a large sea space in the order of hectares and due to its huge structural length-to-thickness ratio, the structural deformation under wave action has to be taken into consideration. The flexible deformation of the structure under hydrodynamic loading is termed the hydroelastic response. Due to the relatively long structural length with respect to the encountering wavelength, the diffraction and radiation of waves have to be taken into account to accurately represent the hydrodynamic loadings on the floating platform. The numerical model is first validated by comparing the eigenvalues and eigenvectors of the OFPV obtained from the proposed numerical scheme with their counterparts obtained from an established finite element software. This is followed by the investigation of the hydroelastic response of various OFPVs designed in varying layout configurations. The various layout configurations are obtained by altering the floating modular units’ dimensions as well as the spacing of the OFPVs when deployed adjacent to each other. The optimal configuration that gives the best performance in terms of the overall smallest response, known as compliance, is then suggested. The results suggest that a longish OFPV layout has a lower hydroelastic response and the motion could be further reduced by increasing the global flexural stiffness via layout arrangement.

Brucella abortus is a facultative intracellular Gram-negative bacterium that causes chronic persistent infections in humans and livestock. In this study, conventional bio-typing, multiple-locus variable-number tandem repeat analysis (MLVA), and whole-genome sequencing-single-nucleotide polymorphism (WGS-SNP) were used to investigate the molecular epidemiology characteristics of Brucella abortus strains in China and their relationships to world lineages. A total of 100 strains were collected from 1953 to 2013, suggesting that B. abortus circulated in China in the past five decades. Moreover, most strains were mainly distributed in the northwest area. During this period, seven biovars were found, indicating that B. abortus displayed a high diversity of biovars and that the main epidemic areas are in the northern provinces. Strains have high genetic diversity, and bruce07 is the most helpful locus for genotyping of this population. Moreover, 17 MLVA-11 genotypes were found; 13 of them are of known genotypes and four are unassigned genotypes, indicating that B. abortus in this study had several geographic origins. Still, strains from unassigned genotypes may originate from China. Many shared MLVA-16 genotypes were observed in strains from the same provinces in Northern China, which confirmed a brucellosis outbreak within northern regions. WGS-SNP analysis showed that eight Chinese strains formed a ladder-like phylogram (C. Ⅶ) with strains from nine countries, including Uganda, Iraq, Russia, Georgia, Spain, Italy, Egypt, Mongolia, and China; strains were introduced to these countries from a single source. Notably, Chinese strains were closely related to strains from Russia and Mongolia; frequent animal (cattle) trade and exchanges may promote this process. We will provide new and insightful information for strength surveillance and control of B. abortus brucellosis in China.

We explored the dynamics of the two interacting information systems. We show that for the Markovian marginal systems the driving force for information dynamics is determined by both the information landscape and information flux. While the information landscape can be used to construct the driving force to describe the equilibrium time reversible information system dynamics, the information flux can be used to describe the nonequilibrium time-irreversible behaviours of the information system dynamics. The information flux explicitly breaks the detailed balance and is a direct measure of the degree of the nonequilibriumness or time irreversibility. We further demonstrate that the mutual information rate between the two subsystems can be decomposed into the equilibrium time-reversible and nonequilibrium time-irreversible parts respectively. This decomposition of the mutual information rate (MIR) corresponds to the information landscape-flux decomposition explicitly when the two subsystems behave as Markov chains. Finally, we uncover the intimate relationship between the nonequilibrium thermodynamics in terms of the entropy production rates and the time-irreversible part of the mutual information rate. We found that this relationship and MIR decomposition still hold for the more general stationary and ergodic cases. We demonstrate the above features with two examples of the bivariate Markov chains.

In this paper we study the class of mixed-index time fractional differential equations in which different components of the problem have different time fractional derivatives on the left hand side. We prove a theorem on the solution of the linear system of equations, which collapses to the well-known Mittag-Leffler solution in the case the indices are the same, and also generalises the solution of the so-called linear sequential class of time fractional problems. We also investigate the asymptotic stability properties of this class of problems using Laplace transforms and show how Laplace transforms can be used to write solutions as linear combinations of generalisedMittag-Leffler functions in some cases. Finally we illustrate our results with some numerical simulations.

In this paper, mineralogical and elemental geochemical characteristics of massive sulfide samples collected from Jade hydrothermal field, located in the Izena depression in the central graben of Okinawa Trough, were analyzed by means of optical microscopy, scanning electron microscopy and electron probe. The results show that the sulfide in Jade hydrothermal area can be divided into Zn-Cu-Pb rich massive sulfide and Zn-Fe rich massive sulfide. The former is composed of sphalerite, galena, anglesite, chalcopyrite and pyrite, and its formation stage can be divided into pyrite stage, sphalerite-chalcopyrite stage, anglesite stage and colloidal pyrite stage. The latter is mainly composed of sphalerite, pyrite, marcasite and a small amount of galena, which can be divided into galena stage, pyrite stage, sphalerite stage, pyrite and marcasite stage. Cu and Zn in pyrite may exist in the form of microinclusions, while Ag and Pb may exist in pyrite in the form of fine galena inclusions containing Ag. Fe and Cu may enter sphalerite in the form of ion replacement. Zn may enter chalcopyrite in the form of ion replacement, and As and Pb may be inclusions in chalcopyrite as As-bearing galena inclusions. Consistent with the previous understanding, the metal elements in the hydrothermal liquid system in Jade hydrothermal field mostly migrate with the hydrothermal fluid as sulfur complexes, and when the hydrothermal fluid mixes with seawater, the physical and chemical conditions of the fluid change, resulting in sulfide mineral precipitation. However, the chemical structure of chalcopyrite is still controversial, which restricts the understanding of the substitution mechanism of trace elements during chalcopyrite precipitation.

. In this paper, we introduce a series of definitions of generalized affine functions for vector-valued functions. We prove that our generalized affine functions have some similar properties with generalized convex functions. We present examples to show that our generalized affinenesses are different from one another, and also provide an example to show that our definition of presubaffinelikeness is non-trivial; presubaffinelikeness is the weakest generalized affineness introduced in this article. We work with optimization problems that are defined and taking values in linear topological spaces. We devote to the study of constraint qualifications, and derive some optimality conditions as well as a strong duality theorem. Our optimization problems have inequality constraints, equality constrains and abstract constraints; our inequality constraints are generalized convex functions and equality constraints are generalized affine functions.

In this paper, we prove that the sub convexlikeness introduced by V. Jeyakumar [1], and the subconvexlikeness defined in V. Jeyakumar [2] are equivalent in loccallly convex topological spaces. And then, we work with set-valued vector optimization problems and obtain some vector saddle-point theorems and vector Lagrangian theorems.

General wisdom thinks that the central of blackholes are singular and featured by mass, charge and spin exclusively; the microstate reflected in the Bekenstein-Hawking entropy can be accounted for only in some quantum gravity. We challenge this wisdom with two exact solution families to the sourceful Einstein equation which describe dust ball with oscillatory inner structure and variety of mass profiles. We attribute the matter content's oscillation across the central point of the system to the forward scattering domination in high energy collisions induced by inter-gravitating acceleration and provide their Penrose-Carter diagram representation and quantum description briefly. Our solution family provides a very simple semi-classic picture for the micorstate definition of black holes.

An outbreak of a virus-like disease has caused severe damage to noni plants (Morinda citrifolia L.) in Xishuangbanna area of China's southwestern Yunnan province since 2015. The diseased plants displayed typical mosaic symptom with light and dark green patches on leaves. Flexuous filamentous virus particles of about 800 nm in length were observed from the leaf saps by transmission electron microscope. Illumina transcriptomic sequencing further revealed the presence of a potyvirus and its near complete genome was obtained from de novo assembly. The complete genome of 9,659 nts was obtained by Sanger sequencing of eight amplicons generate by RT-PCR and 5’ and 3’ RACE. BLASTp analysis of the polyprotein sequence showed that the virus was most closely related to Tobacco vein banding mosaic virus (TVBMV), but these two viruses only shared 50.7% amino acid sequence similarity. Both phylogenetic analyses of the polyprotein and CP amino acid sequences indicated that this virus is a member of genus Potyvirus. However, the low sequence homology with all known potyviruses established this virus as a new species in the genus, tentatively named as Noni mosaic virus (NoMV). Our field surveys showed that 100% of the symptomatic samples and 28.57% of the asymptomatic samples were infected with this novel potyvirus. Aphids collected from diseased leaves were also detected carrying the virus. In summary, our data indicated that a novel species of potyvirus, NoMV, is prevalent in Yunnan, China and is associated with an emerging mosaic disease on M. citrifolia.

High-quality rice (Oryza sativa L.) is increasingly widely planted in China with the improvement of people's living standards and the achievement of rice breeding efforts in recent years. However, the agronomic and physiological performances of high-quality indica rice (HQIR) under different nitrogen(N) application conditions in southern China are little known. Two-year consecutive field experiments were conducted with two HQIR and two ordinary-quality indica rice (OQIR) varieties under moderate and high N application rates, with yield and yield components, biomass, N up-take, and their related traits investigated. We found that grain yields of HQIR were slightly de-creased, but grain yields of OQIR were significantly increased by 6.60%-8.88% under high N rate compared with moderate N rate in both years. Thereby, OQIR produced 8.34%-11.87% and 22.00%-22.50% higher grain yield than HQIR under moderate and high N rates, respectively. The different responses of grain yield to N application rates were mainly due to decreased grain set-ting rate in HQIR and increased spikelets m-2 in OQIR under high N rate. Furthermore, high N rate significantly reduced pre-anthesis AE and improved grain-leaf area ratio, while did not in-crease post-anthesis DM compared with moderate N rate in HQIR, which might result in carbon metabolic deterioration and imbalance of source-sink relationship and subsequently lower supply of carbohydrate to panicle. Our results suggest that a moderate N rate (165 kg N ha-1) is beneficial for HQIR varieties to balance the maximum grain yield and high quality in southern China

This paper proposes an approach for image data extraction and driving behavior analysis using geographic information and driving data. Information derived from geographic and global positioning systems was used for image data extraction. In addition, we used an onboard diagnostic II and a controller area network bus logger to record driving data for driving behavior analysis. Driving behavior was analyzed using sparse automatic encoders and data exploration to detect abnormal and aggressive behavior. A regression analysis was used to derive the relationship between aggressive driving behavior and road facilities. Several traffic improvements were proposed for specific intersections and roads. The results indicate that lane ratios without lane markings and with straight lane markings are important features that affect aggressive driving behaviors.

This study is a two-phase hybrid study on the behavioral activities of undergraduate students during the COVID-19 pandemic lockdown. A questionnaire survey of students during the whole school period and a semistructured interviews with 13 undergraduates of different majors were conducted. First, we found that compared with primary and secondary school students, undergraduates showed many problems with self-time management. Second, the behavior of undergraduates at home may result from multiple factors, such as past experience, professional identity and behavioral habits. When secondary school provided a relatively relaxed learning environment or secondary school teachers placed more emphasis on continuous effort, and when students had a strong sense of the social value of their undergraduate major, students worked harder and achieved more during the pandemic. Otherwise, it was easier for students to slack off and be passive during the pandemic. Altogether, this study deepens our understanding of undergraduates' self-management of free time, and the differences in the values underlying different behaviors and the formation process of various behaviors.

High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

Against the backdrop of the current carbon peaking and carbon neutrality policies, higher requirements have been put forward for the upgrading and construction of smart grids. Non-intrusive load monitoring (NILM) technology is a key technology for advanced measurement systems at the end of the power grid. It obtains detailed power information of the load, without the need for traditional hardware deployment. The key step to solve this problem is load decomposition and identification. This paper first utilized Long Short Term Memory-Denoising Autoencoder(LSTM-DAE) to decompose the mixed current signal on the household busbar and obtain the current signals of multiple independent loads that constituted the mixed current. Then, the obtained independent current signals were combined with voltage signals to generate multi-cycle colored Voltage-Current(VI) trajectories, which were color-coded according to the background. These colored VI trajectories with background colors formed a feature library. When the CNN network was used for load recognition, considering the influence of hyperparameters on recognition results, the BOA algorithm was used for optimization, and the optimized CNN network was employed for VI trajectory recognition. Finally, the proposed method was validated using the PLAID dataset. Experimental results showed that the proposed method exhibited better performance in load decomposition and identification.

Artificial Intelligence (AI) is a breakthrough technology that has been widely applied in many fields and its use in pharmacy is also gaining increasing attentions. Recently, ChatGPT, a newly developed virtual assistant and large language model, is showing strong ability in writing, which makes it a potential tool for review writing. Here in our study, we employ the public available ChatGPT and try to instruct it to generate a mini review on the topic of “lipid-based drug delivery systems” by conversation. Our results showed that ChatGPT can give reasonable outline for this topic and give seemingly sentences with concluding wording, which can give useful information to the readers. However, the accuracy and consistence of the review are not fully guaranteed and there is lack of reliable citations. Therefore, it is concluded that ChatGPT can only give general knowledge on the selected topic, but not capable of giving in-depth discussion. The generated review article can be a useful but occasionally unprecise electronic encyclopedia instead of rigorous scientific literature, which can give benefit for pharmaceutical education and interchange to some extent.

This study presents an instant preview and analysis system implementation of intelligent stereo cameras (ISCs). A parameter optimization prototype adopted the instant preview and analysis system of the ISCs has been achieved the automatic alignment function, and obtained optimal stereo films with the automatic alignment function by adjusting gap and angle between dual cameras. The instant preview and analysis system of the ISCs with parameter optimization can enhance the quality of stereo films effectively and reduce filmed errors and save retouched cost and time in harsh filmed environment.

The negative impact of the modern-day lifestyle on the environment is aggravated during the COVID-19 pandemic through the increased use of single-use plastics from food takeaways to medical supplies. Similarly, the closure of food outlets and disrupted supply chains have also resulted in significant food wastage. As the pandemic rages on, the aggravation of increased waste becomes an increasingly urgent problem that threatens the biodiversity, ecosystems, and human health worldwide through pollution. While there are existing methods to deal with the organic and plastic waste, many of the solutions also cause additional problems. Increasingly proposed as a natural solution to man-made unnatural problems, there are insect solutions for dealing with the artificial and organic waste products towards a circular economy, making the use of natural insect solutions commercially sustainable. This review discusses the findings and how some of these insects, particularly the Hermetia illucens, Tenebrio molitor, and Zophobas morio, can play an increasing important role in food and plastics, with a focus on the latter.

Climate change poses a serious threat to the ancient Magnoliaceae family, particularly for the endangered Yulania trees. Until now, little is known about the suitable geographical range of Yulania zenii, and about how it responds to past and future climate scenarios. Here, we first employed ten models from Biomod2 to preliminarily simulate its potential distribution in China and selected MaxEnt for final modeling. The results showed that among the key environmental factors influencing its distribution, the top three factors were Bio2 (Mean diurnal range), Bio15 (Precipitation seasonality of variation coefficient) and Elevation. Its current suitable distribution were primarily concentrated in southern Anhui, central Hubei, eastern Hunan, southern Jiangsu, northern Jiangxi, and northern Zhejiang. The total suitable area of Yulania zenii was 14.68 × 104 km2, only taking 1.53% of China's total territory, which is larger than known. During the Last Interglacial and Middle Holocene, its suitable habitats were larger than currently, exhibiting a relatively continuous distribution. Under various future climate scenarios, its suitable habitats may averagely decrease by 20.26% compared with the current, and these habitats become more fragmented. Collectively, the centroid of Yulania zenii is expected to migrate towards the southeast in the future. Therefore, our findings demonstrate, for the first time, that climate change takes an adverse effect on this species in distribution from the past to current till future. Our study can contribute to the conservation and management of Yulania zenii in China, and can provide reference for other endangered Yulania species of this country under the condition of climate change.

The aim of this paper is to use deep learning tools to innovate pre-trained object detection models to improve the accuracy of non-destructive testing (NDT) of civil aviation maintenance. First, this thesis classifies object defects for NDT, such as cracks, undercut, etc. Nowadays, thesis surveys innovation deep-learning methods technology is used to improve the defect detection performance inferencing capability, increase the accuracy and efficiency of automatic identification which in enhanced the safety and reliability of aircraft fuselage in future, mark hidden cracks and solve the challenges that cannot be identified by manual inspection. Second, recent mainstream techniques the YOLOv4 neural network to the graphics card GPU core operator to speed up the recognition of defect images is being applied to the non-destructive inspection process of aircraft maintenance on A, C and D-Level, fully validating the deep learning model's powerful defect detection target capability. The attention-based YOLOv4 algorithm is improved by applying a one-stage attention mechanism to the YOLOv4, thereby improving the accuracy of the innovation model. Finally, thesis improved YOLOv4 based on an attention mechanism is proposed for object detection NDT via the deep learning method to effectively improve and shorten the inspection anomaly detection method for automatic detection sensor systems.

To ensure the safety in aircraft flying, we aim use of the deep learning methods of nondestructive examination with multiple defect detection paradigms for X-ray image detection posed. The use of the Fast Region-based Convolutional Neural Networks (Fast R-CNN) driven model seeks to augment and improve existing automated Non-Destructive Testing (NDT) diagnosis. Within the context of X-ray screening, limited numbers insufficient types of X-ray aeronautics engine defect data samples can thus pose another problem in training model tackling multiple detections perform accuracy. To overcome this issue, we employ a deep learning paradigm of transfer learning tackling both single and multiple detection. Overall the achieve result get more then 90% accuracy based on the AE-RTISNet retrained with 8 types of defect detection. Caffe structure software to make networks tracking detection over multiples Fast R-CNN. We consider the AE-RTISNet provide best results to the more traditional multiple Fast R-CNN approaches simpler translate to C++ code and installed in the Jetson™ TX2 embedded computer. With the use of LMDB format, all images using input images of size 640 × 480 pixel. The results scope achieves 0.9 mean average precision (mAP) on 8 types of material defect classifiers problem and requires approximately 100 microseconds.

A flexible asymmetric supercapacitor (ASCs) is successfully developed by using the composite of MoO3 and graphene oxide (GO) electrochemically deposited on carbon cloth (CC) (MoO3/rGO/CC) as the negative electrode, the MnO2 deposited on CC (MnO2/CC) as the positive electrode and Na2SO4/polyvinyl alcohol (PVA) as gel electrolyte. The results show that the introduction of GO layer can remarkably increase the specific capacitance of MoO3 from 282.7 F g-1 to 341.0 F g-1. Furthermore, the combination of such good electrode materials and a neutral gel electrolyte renders the fabrication of high-performance ASC with a large operating potential difference of 1.6 V in 0.5 mol L-1 Na2SO4 solution of water. Furthermore, the ASCs exhibit excellent cycle ability and the capacitance can maintain 87 % of its initial value after 6000 cycles. The fact that a light-emitting diode can be lighted up by the ASCs indicates the device’s potential applications as energy storage devices. The encouraging results demonstrate a promising application of the composite of MoO3 and GO in energy storage devices.

Postmenopausal osteoporosis, a metabolic bone disease associated with aging and that affects bones throughout the body, is emerging as an urgent public health concern and imposes a substantial healthcare burden on society. The clinical application of bisphosphonate, the primary treatment for osteoporosis, is limited owing to the drug’s severe complications. Herein, we investigate the synthesis and utilization of strontium-doped mesoporous bioactive glass loaded with alendronate (ALN@Sr-MBG) as a novel therapeutic agent for osteoporosis, to explore its potential as an alternative to alendronate (ALN). Strontium-doped mesoporous bioactive glass (Sr-MBG) was synthesized using the sol-gel method, while ALN@Sr-MBG was obtained by incorporating Sr-MBG into an alendronate saturated solution. The bioactivities of ALN@Sr-MBG, including biotoxicity, inflammation inhibition, and anti-osteoclast differentiation, were investigated in vitro using CCK-8, flow cytometry, tartrate-resistant acid phosphatase (TRAP) staining, and RT-PCR assays. Animal models were established by surgically removing the ovaries from non-pregnant female C57/BL mice, followed by weekly intraperitoneal injections of ALN@Sr-MBG, ALN, or excipients. After 8 weeks, the mice femurs were extracted and analyzed through Micro-CT scanning, and hematoxylin-eosi, osteoblastic, and osteogenic staining. The in vitro findings demonstrated that ALN@Sr-MBG displayed enhanced biological efficacy compared to ALN in terms of inflammation inhibition, osteogenesis promotion, and osteoclastogenesis inhibition. Furthermore, micro-CT analysis revealed that ALN@Sr-MBG significantly augmented bone mineral density (BMD), bone volume fraction (BV/TV), trabecular number (Tb.N), and trabecular thickness (Tb.Th), while reducing trabecular separation (Tb.Sp) and structural model index (SMI) in mice with ovariectomy-induced osteoporosis. The osteoblast and osteogenic staining results indicate the enhanced bioactivities of ALN@Sr-MBG in promoting bone formation and inhibiting bone resorption compared to ALN. In vitro and in vivo assessments further confirmed that ALN@Sr-MBG exhibits superior anti-osteoporotic bioactivity compared to ALN. The study findings confirm the potential of ALN@Sr-MBG as a novel alternative therapy to ALN and drug candidate for the treatment of osteoporosis.

Tremor is a prevalent neurological disorder characterized by involuntary shaking or trembling of body parts. This condition impairs fine motor skills and hand coordination to varying degrees and can even affect overall body mobility. As a result, tremors severely disrupt the daily lives and work of those affected, significantly limiting their physical activity space. This study developed an innovative Spatial Augmented Reality (SAR) system aimed at assisting individuals with tremor disorders to overcome their physical limitations and expand their range of activities. The system integrates eye-tracking and Internet of Things (IoT) technologies, enabling users to smoothly control objects in the real world through eye movements. It employs a virtual stabilization algorithm for stable interaction with objects in the real environment. The study comprehensively evaluated the system's performance through three experiments: 1) assessing the effectiveness of the virtual stabilization algorithm in enhancing the system's ability to assist individuals with tremors in stable and efficient interaction with remote objects; 2) evaluating the system's fluidity and stability in performing complex interactive tasks; 3) investigating the precision and efficiency of the system in remote interactions within complex physical environments. The results demonstrate that the system significantly improves the stability and efficiency of interactions between individuals with tremor and remote objects, reduces operational errors, and enhances the accuracy and communication efficiency of interactions.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

Dryland winter wheat in Loess Plateau is facing yield reduction due to shortage of soil moisture and delayed sowing time. Field experiment was conducted at Loess Plateau in Shanxi Province, China from 2012 to 2014, to study the effect of subsoiling and conventional tillage and different sowing dates on the soil water storage and contribution of N accumulation and remobilization to yield of winter wheat. The results showed that subsoiling significantly improved the soil water storage at 0-300 cm depth, improved the number of tillers and pre-anthesis N translocation in various organs of wheat and post-anthesis N accumulation, eventually increased the yield up to 17-36%. Delaying sowing time had reduced the soil water storage at sowing and winter accumulated temperature by about 180˚C. The contribution of N translocation to grain yield was maximum in glume+spike followed by in leaves and minimum by stem+sheath. In addition a close relationship was found between the N accumulation and translocation and the soil moisture in the 20-300 cm. Subsoiling during the fallow period and the medium sowing date was beneficial for improving the soil water storage and increased the N translocation to grain, thereby increasing the yield of wheat, especially in dry year.

The average working person can spend between 35-60 hours a week in the workplace, making it an influential place for mental well-being while also being a place for socio-economic contribution. Workplace incivility can diminish positive mental health outcomes and negatively impact work engagement through increased social anxiety. To investigate this, 118 working adults aged between 19 to 67 years old in Singapore were recruited for a survey comprising of demographics questions, the Workplace Incivility Scale, Brief DSM-5 Social Anxiety Disorder Severity Scale, Utrecht Work Engagement Scale-9 over the period of November 2022 to April 2023. Correlational, regression and mediation analysis showed workplace incivility scale scores to significantly pre-dict social anxiety after controlling for covariates, supporting our hypothesis that employees exposed to work-place incivility would have higher levels of social anxiety that mediated work engagement after controlling for age and gender. The findings here show workplace incivility to be a possible intervention target for social anx-iety to reduce negative impacts on work engagement in order to improve employee experience and retention for organizations.

Although the positive relationship between religion and environmental behavior is well-argued, empirical research about the relationship between religion and public pro-environmental behavior is relatively lacking. This paper aims to explore the group differences in the influence of religion on public pro-environmental behavior and the mediating role of environmental risk perception in religion and public pro-environmental behavior. Using the Chinese General Social Survey data in 2013 for empirical analysis, this study’s results show that there are group differences in the impact of religion on public pro-environmental behavior. Women with religious beliefs are more willing to engage in public pro-environmental behavior than those without religious beliefs. Religious believers over the age of 45 are more willing to participate in public pro-environmental behavior than those without religious beliefs. Political participants with religious beliefs are more willing to practice public pro-environmental behavior than those without religious beliefs. In addition, we found that environmental risk perception can act as partial mediation in religious and public pro-environmental behavior. In other words, religious beliefs are deeply embedded in local political and social culture. In order to correctly understand the relationship between religion and public pro-environmental behavior, it is necessary to consider religion in a specific cultural background.

Plant Cysteine Oxidase (PCO) is a plant O2-sensing enzyme of catalyzing oxidation of cysteine to Cys-sulfinic acid at the N-termini of target proteins. To better understand the Brassica napus PCO gene family, PCO genes in B. napus and related species were analyzed. In this study, 20, 7 and 8 PCO genes were identified in Brassica napus, Brassica rapa and Brassica oleracea, respectively. According to phylogenetic analysis, the PCOs were divided into five groups: PCO1, PCO2, PCO3, PCO4 and PCO5. Gene organization and motif distribution analysis suggested that PCO gene family was relatively conserved during evolution. Expression analysis showed that PCO genes were expressed in different tissues at different developmental stages. Interestingly, most of the Bna/Br/BoPCO5 members were expressed in leaves, roots, flowers, buds and siliques, suggesting an important role in both vegetative and reproductive development. Expression of BnaPCO was induced by various abiotic stress, especially waterlogging stress, which was consistent with the result of cis-element analysis. In this study, the PCO gene family of Brassicaceae was analyzed for the first time, which contributes to a comprehensive understanding of the origin and evolution of PCO genes in Brassicaceae and the function of BnaPCO in regulating plant responses to abiotic stresses.

These years have witnessed growing research on applying rheology in grinding and flotation treatment of finely disseminated ores. The slurry rheology has long been identified as the comprehensive effect of inter-particle interactions, including their aggregation (coagulation and flocculation) and dispersion states in slurry, which are more impactive under the fine-particle effect. In this regard, rheology has the potential to play a significant role in interpreting the flowing and deforming phenomenon of inter-particle aggregates, particle-bubble aggregates, and flotation froth. Though much attention has been paid to the rheological effect in industrial suspension, this has not been the case for mineral grinding and flotation for fine particles. The influential mechanism of rheology on the sub-processes of mineral processing has not been systemically concluded and revealed thoroughly, without which the underpinning mechanism for enhancing the processing efficiency has been difficult to discover. This paper reviews the current application and importance of rheology in the fine mineral processing, and the potential research direction in the field is proposed.

The model internal year-to-year variability (hereafter, internal variability) is a significant source of uncertainty when estimating anthropogenic aerosol effective radiative forcing (ERF). In this study, we investigate the impact of internal variability using large ensemble simulations (600 years in total) with the same climate model under prescribed anthropogenic aerosol forcings. A comparison of the magnitudes (i.e., standard deviation, Std) of these influences confirms that internal variability has negligible impacts on the instantaneous radiative forcing (RF) diagnosed by double radiation calls but has considerable impacts on estimating ERF through rapid adjustments (ADJ). Approximately half of the model grids exhibit strong internal variability influence on ERF (Std &gt; 5 W m−2). These strong internal variabilities lead to a 50% probability that 30-year linear change can reach 2 W m−2, and 10-year linear change can reach 4 W m−2. A 50-year simulation can provide a relatively stable annual mean map of ERF (ERF = ADJ + RF), but it fails for ADJ. The statistically significant areas in the annual mean maps of both ERF and ADJ from a 10-year simulation exhibit instability with evident chaotic features. These analyses contribute to the setup of comparative experiments and a more comprehensive understanding of the modeled anthropogenic aerosol ERF.

The Marchenko method is a data-driven way which makes it possible to calculate Green's functions from virtual points in the subsurface by the reflection data at the surface, only requiring a macro velocity model. This method requires collocated sources and receivers. However, in practice, subsampling of sources or receivers will cause gaps and distortions in the obtained focusing functions and Green's functions. To solve this problem, this paper proposes to integrate sparse inversion into the iterative Marchenko scheme. Specifically, we add sparsity constraints to the Marchenko equations and apply sparse inversion during the iterative process. Our work not only reduces the strict requirements on acquisition geometries, but also avoids the complexity and instability of direct inversion for Marchenko equations. This new method is applied to a two-dimensional numerical example with irregular sampled data. The result shows that it can effectively fill gaps of the obtained focusing functions and Green's functions in the Marchenko method.

Silicon anodes have been considered one of the most promising anode candidates for the next generation of high-energy density lithium-ion batteries due to the high theoretical specific capacity (4200 mAh g-1) of Si. However, high lithiation capacity endows silicon anodes with severe volume expansion effects during the charge/discharge cycling. The repeated volume expansions not only lead to the pulverization of silicon particles and the separation of electrode materials from the current collector, but also brings rupture/formation of solid electrolyte interface (SEI) and also continuous electrolyte consumption, which seriously hinders the commercial application of silicon anodes. Structural design and optimization is the key to improving the electrochemical performances of silicon anodes, which has attracted wide attention and research in recent years. This paper mainly summarizes and compares the latest research progress for the structural design and optimization of silicon anodes.

This research analyses extreme precipitation events in the Huaihe River Basin in China, a densely populated region with a history of human settlements and agricultural activities. This study aims to explore the impact of extreme precipitation index changes and provide decision-making suggestions for flood early warning and agricultural development in the Huaihe River Basin. The study utilises the NEX-GDDP-CMIP6 climate models dataset and the daily value dataset (V3.0) from China's national surface weather stations to investigate temporal and spatial changes in extreme precipitation indices from 1960 to 2014 and future projections. At the same time, this study adopted the RclimDex model, Taylor diagram and Sen+Mann-Kendall trend analysis research methods to analyse the data. The results reveal a slight increase in extreme precipitation indices from northwest to southeast within the basin, except for CDD, which shows a decreasing trend. Regarding spatial, the future increase of extreme precipitation in the Huaihe River Basin will show a spatial variation characteristic that decreases from northwest to southeast. These findings suggest that extreme precipitation events are intensifying in the region. Understanding these trends and their implications is vital for adaptation strategy planning and mitigating the risks associated with extreme precipitation events in the Huaihe River Basin.

Chicken infectious anemia (CIA) poses a significant threat to the chicken industry in China. De-spite its non-specific symptoms, the disease is often overlooked. This study aimed to conduct a comprehensive analysis of the etiology and pathology of CIA in Guangxi Province, China. Three strains of the chicken infectious anemia virus (CIAV) were isolated from liver samples of diseased 20-week-old chickens. The complete genomes of these strains were sequenced, and experiments on specific pathogen-free (SPF) chicks revealed that the GX21121 strain exhibited high virulence. Histopathological examination of the deceased chicks showed liver cell necrosis, fibrous-serous exudation, inflammatory cell infiltration, hemorrhage in liver tissues, as well as congestion in lung and renal tissues. Phylogenetic analysis of the genome revealed that the three strains had a close genetic relationship to the Heilongjiang wild-type (GenBank KY486144). The genetic evolu-tion of their VP1 genes indicated that all three CIAV isolates belonged to genotype IIIc. In sum-mary, this study demonstrated the genomic diversity of three CIAV strains in adult layer hens. The isolation and characterization of the GX21121 strain as a highly virulent isolate provide val-uable information for further investigations into the etiology, molecular epidemiology, and viral evolution of CIAV.

The phenomenon of ordered self-assembly on solid substrates is a topic of interest in both fundamental surface science research and its applications in nanotechnology. The regulation and control of two-dimensional (2D) self-assembled supra-molecular structures on surfaces have been realized through applying external stimuli. By utilizing scanning tunneling microscopy (STM), researchers can investigate detailed phase transition process about self-assembled monolayers (SAMs), providing insight into the interplay between intermolecular weak interactions and substrate-molecule interactions, which govern the formation of molecular self-assembly. This review will discuss the structural transition of self-assembly probed by STM in response to external stimuli and provide state-of-art methods such as tip induced confinement for the alignment of SAM domains and selective chirality. Finally, we discuss the challenges and opportunities in the field of self-assembly and STM.

Rail impedance directly affects the transmission performance of track circuit . Considering the condition of earth stratification, for the difficult to calculate the rail impedance due to the semi-infinite integration interval and the oscillation of the integrand by using the Carson formula, The truncation method is proposed to divide the impedance formula is divided into definite integral and tail integral. The integral is approximated by the spline function, and the tail integral is calculated by using the exponential integral and Euler formula. Based on it, the rail impedance calculation formula of track circuit is obtained. The electromagnetic field model of track circuit with earth stratification is simulated by finite element method, and the correctness of the method is verified. Based on the formula, the influence of current frequency, soil depth and conductivity on rail impedance is studied. The relative error between the calculated results of rail impedance and the simulation results of finite element is within 5%. It can be seen that the formula has high accuracy and correctly reflects the law of rail impedance variation with current frequency, soil depth and resistivity. It provides a reliable reference for the theoretical calculation of rail impedance of track circuit.

As the number of end-of-life vehicles continues to grow, the field of separation technology for broken copper and aluminium parts of end-of-life vehicles has emerged as a significant area of research. As a key technology for the separation of non-magnetic non-ferrous metals, such as copper and aluminium, eddy current separation can achieve efficient separation of non-magnetic non-ferrous metals according to their differing conductivity and density. Nevertheless, further research is required in the separation of large-scale broken copper and aluminium parts of end-of-life vehicles. This paper presents a novel magnetic roller model comprising circumferential and axial periodic arrangements of permanent magnets. A single permanent magnet was constructed as an equivalent current model, and the magnetic scalar potential equations were solved using simulation tools. This allowed the distribution of the magnetic field outside the magnetic roller to be studied. The results demonstrate that the novel permanent magnet array magnetic roller can enhance the magnetic field intensity and action distance of the external magnetic field, which is more conducive to the separation of large-scale broken copper and aluminium parts of scrap cars. The findings of this research provide a theoretical foundation for the separation of scrap car broken copper and aluminium parts.

Red mud (RM), a bauxite residue, contains hazardous radioactive wastes and alkaline material and poses severe surface water and groundwater contamination risks, necessitating recycling. Pretreated RM can be used to make adsorbents for water treatment. However, its performance is affected by many factors, resulting in a nonlinear correlation and coupling relationship. This study aimed to identify the best formula for an RM adsorbent using a mathematical model that examines the relationship between 11 formulation types (e.g., pore-assisting agent, component modifier, and external binder) and nine properties (e.g., specific surface area, wetting angle, and Zeta potential, among others). This model was built using a back-propagation neural networks(BP) based on single-factor experimental data and orthogonal test data. The model trained and predicted the established network structure to obtain the optimal adsorbent formula. The RM particle adsorbents had a pH of 10.16, specific surface area(BET) of 48.92 m2·g−1, pore volume of 2.10 cm3·g−1, compressive strength(ST)) of 1.12 KPa, and 24-h immersion pulverization rate(η_m) of 3.72%. In the removal of total phosphorus in flotation tailings backwater, it exhibited a good adsorption capacity (Q)and total phosphorous removal rate(η) of 48.63 mg·g−1 and 95.13%, respectively.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

This study examined the tourism spatial distribution of nine cities in the Fujian province and assessed the impacts of COVID-19. The modified gravity model found that it was widely dispersed, with uneven and relatively independent tourism development in different cities. The social network analysis showed that tourism connections across cities were significantly reduced after the pandemic. The impacts of brand awareness and transport accessibility on spatial networks were positive in pre-pandemic but became negative during the pandemic. In contrast, tourist volume had negative impacts on spatial networks in pre-pandemic but had positive ones during the pandemic. Tourism resources and market performance had significantly positive impacts in the post-pandemic era. These findings provide advice on tourism recovery and destination management in coping with future critical events. It also contributes to the theoretical gravity framework in tourism and the research scope of the social networks analysis at the city level.

Globally,coastal regions are vital areas of human activities and, as such, are centres of population growth and urban and economic development. Long-term human development has had a major impact on the ecological environment of coastal zones. Therefore, exploring the distribution and provenance of marine sediment types in coastal areas heavily influenced by human activities can provide scientific evidence and references for the current and future ecological management of these sensitive environments. For this reason, we have conducted an analysis on the sediment grain size, Endmember, organic matter content and geochemical elements in the Lu’erhuan River‒Malan Island‒Sandun Island area in the eastern part of Qinzhou Bay, a region heavily influenced by human activities. Sediment grain size clearly differs throughout the study site and the material provenances and hydrodynamic conditions are also varied, likely due to the local environmental conditions and the significant impact human activities have had on the area. The finest-grained sediment is imported from either inland or coastal areas via rivers and weak tidal currents, the next finest component is input from coastal areas through weak tidal currents, and the moderately coarse component mainly originates from nearby beaches. The two coarsest-grained sediment components are influenced by the combination of human activities, tidal currents and waves and enter the water via erosion. Organic matter provenance resembles that of the sediment components, exhibiting varied characteristics. This is due to the combination of natural and human activities in the bay. The organic matter in the upper reaches of the Lu’erhuan River originates from the river and coastal paddy fields, with obvious terrigenous characteristics; the organic matter in northern Malan Island mainly comes from external sources related to oyster farming; while organic matter in eastern Sandun Island is mainly produced endogenously by marine plankton. Al, Ti, Fe, Mg, K, Ga and other elements indicate that terrestrial sediments are significantly disturbed by human activities. However，Mn reflects the marine distribution of terrestrial sediments from the Lu’erhuan River to Jishuimen. Ca and Sr, indicators of marine sediments, are distributed in the eastern offshore area of Sandun Island, which is connected to the open waters. Due to the influence of human activities, As and Cd are highly enriched in the study area, while Cu is less affected by human activities.

Metabolites present in the hemolymph of honey bees play a crucial role in modulating the metamorphic process within the species. However, the precise alterations in metabolite composition, along with the associated variances and regulatory pathways implicated during the larvae-to-pupae metamorphosis of honey bees, remain incompletely elucidated. In this investigation, we gathered hemolymph samples from honey bee larvae at three distinct physiological stages-feeding, prepupal, and pupae and subjected them to metabolite analysis utilizing the liquid chromatography-mass spectrometry (LC-MS) technique. Employing principal component analysis (PCA) and partial least squares-discriminant analysis (PLS-DA), we identified significant differential metabolites and conducted a metabolic pathway analysis on those differentially up-regulated during the prepupal and pupae stages. Notably, metabolites up-regulated in the hemolymph of prepupal stage larvae primarily governed glucose metabolism and fat digestion and absorption, while those in pupae stage larvae were involved in regulating chitin and lipopolysaccharide precursor formation, as well as the biosynthesis of phenylalanine, tyrosine, and tryptophan. These findings bear significant implications for advancing our comprehension of the metamorphic processes in honey bees.

Initial water content significantly affects the efficiency of soil stabilization. In this study, the effects of initial water content on the compressibility, strength, microstructure and composition of a lean clay soil stabilized by compound calcium-based stabilizer were investigated by static compaction test, unconfined compression test, optical microscope observations, environment scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction spectroscopy. The results indicate that as the initial water content increases in the range studied, both the compaction energy and the maximum compaction force decrease linearly and there are less soil aggregates or agglomerations, and smaller proportion of large pores in the compacted mixture structure. In addition, for specimens cured with or without external water supply and under different compaction degrees, the variation law of the unconfined compressive strength with initial water content is different and the highest strength value is obtained at various initial water contents. With the increase of initial water content, the percentage of oxygen element tends to increase in the reaction products of the calcium-based stabilizer, whereas the crystalline mineral of the soil did not change obviously.

We found an important fact that the beam footprint line of Ping will intersect with the real water depth when the initial incidence angle is about 45°, and sound velocity error hardly has an effect on it. This is contrary to our previous experience that the soundings of the central beam of multi-beam bathymetric system (MBS) is the most accurate. Firstly, the influence of sound velocity errors on central beam and seafloor topography distortion was analyzed. Secondly, the process of proving this fact was given, and the topography correction method was proposed by compensating the sound velocity profile area (SVP area). Finally, we showed in the first simulation of four type errors in SVPs that this fact is verified. The topography correction method used in the second simulation to correct the topography distortion of the first simulation is also verified.

Hydrological connectivity plays a major role in solving water resource and eco-environmental problems. However, this phenomenon has not been afforded the attention it deserves. Detailed analysis of connectivity in river systems could provide considerable insight into structural and functional attributes of riverine landscapes. The current study used graph theory approach and associated connectivity indicators to explore the characteristics and evolution of river systems and hydrological connectivity in a large catchment (Poyang Lake, China). The results revealed that the structure of the river system tended to be complex during 1990-2020, characterized by a dynamic evolution of tributaries in certain northern areas. Both river density and complexity exhibited an increasing trend by up to 15%, with the change rate after 2000 approximately twice as high as that of the preceding period. Overall, human activities across the catchment are more likely to play a key role in leading to significant changes in the quantity, morphometric, and structure characteristics of the river system. Additionally, the functional connectivity analysis indicated that the index of connectivity (IC) in the downstream catchment is stronger than that of the upstream vegetation areas, suggesting a strong contribution to the runoff-sediment transport (r=0.6-0.7). This study highlights the spatial and temporal evolution of both the structural and functional connectivity in the large Poyang Lake catchment. The findings of this work will bene-fit future water resource management and applications by providing a strategy for protecting the surface hydrology and mass transport of large river basins under climate and land-use changes.

Taking a certain type of test centrifuge as the research object, the finite element model of the test centrifuge is established, the vibration characteristics and aerodynamic performance of the test centrifuge are analyzed, and the structural optimization design of the test centrifuge is carried out. In this paper, the load is applied according to the actual working condition of a certain type of test centrifuge. The vibration of the mounting seat of the test centrifuge is analyzed and the structure of the mounting seat is optimized. After optimization, the vibration of the mounting seat is 77.38 % lower than that of the original mounting seat. Then, the aerodynamic analysis of the test centrifuge is carried out. The analysis results show that the test centrifuge moves more smoothly under the whole package shell and the steady flow shell, and the resistance decreases and the shaft load decreases. Finally, the steady flow shell of the test centrifuge is optimized. The analysis shows that the increase of the width of the steady flow shell can reduce the resistance coefficient, which is helpful to the stability of the test centrifuge during operation and reduces the unbalanced response of the system caused by air resistance.

Diffuse cavernous hemangioma of the rectum (DCHR) is a rare benign lesion of vascular malformation. According to previous studies, the most reported major symptoms of DCHR are recurrent painless rectal bleeding or iron deficiency anemia[1][2][3][4][5][6]. We present a case of an 8Y11M boy who was diagnosed with DCHR by MRI. The patient underwent Laparoscopic-assisted transanal distal sigmoidectomy and sigmoido-anal anastomosis（Laparoscopic Swenson Procedure）, and recovered well. After the operation, the child had short-term fecal incontinence and loose stools, which returned to normal after half a year. Regardless of age and symptoms, early and correct diagnosis and treatment of DCHR and postoperative restoration of normal anal function are necessary. Laparoscopic Swenson procedure may be a good option for the treatment of DCHR.

Quantum coherence is an important physical resource in quantum information science, and also as one of the most fundamental and striking features in quantum physics. In this paper, we obtain a symmetry-like relation of relative entropy measure $C_r(\rho)$ of coherence for $n$-partite quantum states $\rho$, which gives lower and upper bounds for $C_r(\rho)$. Meanwhile, we discuss the conjecture about the validity of the inequality $C_r(\rho)\leq C_{\ell_1}(\rho)$ for any state $\rho$. We observe that every mixture $\eta$ of a state $\rho$ satisfying $C_r(\rho)\leq C_{\ell_1}(\rho)$ and any incoherent state $\sigma$ also satisfies the conjecture. We also note that if the von Neumann entropy is defined by the natural logarithm $\ln$ instead of $\log_2$, then the reduced relative entropy measure of coherence $\bar{C}_r(\rho)=-\rho_{\rm{diag}}\ln \rho_{\rm{diag}}+\rho\ln \rho$ satisfies the inequality ${\bar{C}}_r(\rho)\leq C_{\ell_1}(\rho)$ for any mixed state $\rho$.

Drug-target affinity (DTA) prediction is crucial for understanding molecular interactions and aiding drug discovery and development. While various computational methods have been proposed for DTA prediction, their predictive accuracy remains limited, failing to delve into the structural nuances of interactions. With increasingly accurate and accessible structure prediction of targets, we developed a novel deep learning model, named S2DTA, to accurately predict DTA by fusing sequence and structural knowledge of drugs, targets, and pockets using heterogeneous models based on graph and semantic networks. Experimental findings underscored that complex feature representations imparted negligible enhancements to the model’s performance. However, the integration of heterogeneous models demonstrably bolstered predictive accuracy. In comparison to three state-of-the-art methodologies, the supremacy of S2DTA became strikingly apparent. It showcased a noteworthy 25.2% reduction in Mean Absolute Error (MAE) and an impressive 20.1% decrease in Root Mean Square Error (RMSE). Furthermore, S2DTA exhibited substantial advancements in other pivotal metrics, including Pearson Correlation Coefficient (PCC), Spearman, Concordance Index (CI), and R2. These metrics experienced remarkable increments of at least 19.6%, 17.5%, 8.1%, and a remarkable 49.4%, respectively. Finally, we conducted interpretability analysis on the effectiveness of S2DTA by bidirectional self-attention mechanism, fully proving that S2DTA is a valuable and accurate tool for predicting DTA. For further exploration, the source data and code repository can be accessed at https://github.com/dldxzx/S2DTA.

As a widely used plastic, the aging and degradation of polyethylene (PE) are inevitable problems, whether the goal is to prolong the life of PE products or address the issue of white pollution. Molecular simulation is a vital scientific tool in elucidating the mechanisms and processes of chemical reactions. To obtain the distribution and evolution process of PE's thermal oxidation products, this work employs the self-consistent charge density functional tight binding (SCC-DFTB) method to perform molecular simulations of the thermal oxidation of PE with different crystallinity and branched structures. We discovered that crystallinity does not affect the thermal oxidation mechanism of PE, but higher crystallinity makes PE more susceptible to cross-linking and carbon chain growth, reducing the degree of PE carbon chain breakage. The branched structure of PE results in differences in pore size between the carbon chains, with larger pores leading to a concentrated distribution of O2 and free radicals subsequently formed. The breakdown of PE is slowed down when free radicals are localized in low-density regions of the carbon chain. The specifics and mechanism of PE's thermal oxidation are clearly revealed in this paper, which is essential for understanding the process in-depth and for the development of anti-aging PE products.

Due to the lack of theoretical research on the amount of spatio-temporal information in the high-speed photography technologies, obtaining an optimized system with a best amount of spatio-temporal information remains a challenge, resulting in insufficient effective information and observation accuracy for ultrafast events. The paper presents an ultrafast raster imaging (URI) system with a large amount of spatio-temporal information based on the all-optical raster principle in single-shot. Specifically, we derive the optimal equation of spatial resolution and the expression for the maximum amount of spatio-temporal information that can achieve excellent performance for an URI system. It serves as a general guideline for getting a large amount of information design in the URI system. Compared to the existing URI systems, the advanced URI system exhibits an improvement of nearly 1 order of magnitude in the amount of spatio-temporal information, and more than twofold in spatial resolution. It shows a great potential for capturing intricate and non-repetitive ultrafast events on the femtosecond time scale.

Zearalenone is one of the most prevalent estrogenic mycotoxins produced mainly by Fusarium family fungi, and harmed the heath of animals. Zearalenone hydrolase is an important enzyme capable of degrading zearalenone into a non-toxic compound. Although previous research has investigated the catalytic mechanism of zearalenone hydrolase, information on its dynamic interaction with zearalenone remains unknown. This study aimed to develop a pipeline for identifying the allosteric pathway of zearalenone hydrolase. Using an identity analysis, we identified hub genes whose sequences can generalize a set of sequences in a protein family. We then utilized a neural relational inference (NRI) model to identify the allosteric pathway of the protein throughout the entire molecular dynamics simulation. The production run lasted 1 microsecond, and we analyzed residues 139-222 for the allosteric pathway using the NRI model. We found that the cap domain of the protein opened up during catalysis, resembling a hemostatic tape. We used umbrella sampling to simulate the dynamic docking phase of the ligand-protein complex and found that the protein took on a square sandwich shape. Our energy analysis using both MMPBSA and PMF analysis showed discrepancies, with scores of -8.45 kcal/mol and -1.95 kcal/mol, respectively. MMPBSA, however, obtained a similar score to that of a previous report.

Privacy and information insurance have consistently been a priority for the European Union lawmaker. This paper presents whether the NIS prevails in its underlying endeavors to remain the congruity among residents and companies. It distinguishes current difficulties that specific business structures may experience while conforming to the Regulation. The exploration traces certain reasons which could impede the opportune reception of the new lawful ideas inside the system of the organizations. The exploration incorporates what is unique about the NIS; how it overlaps with existing frameworks; and how security requirements in the GDPR influence the NIS Directive. This paper furnishes different point of views of experts with the aim of setting up an entire examination

Infrared small target detection (ISTD) plays a crucial role in both civilian and military applications. The detection of small targets against dense cluttered backgrounds remains a challenging task, requiring the collaboration of false alarm source elimination and target detection. Existing approaches primarily focus on modeling targets while often neglecting false alarm sources. To address this limitation, we propose a Target and False Alarm Collaborative Detection Network to leverage the information provided by false alarm sources and the background. Firstly, we introduce a False Alarm Source Estimation Block (FEB) that estimates potential interferences present in the background by extracting features on multiple scales and employing stepwise upsampling for feature fusion. Subsequently, we propose a framework that employs multiple FEBs to eliminate false alarm sources across multiple scales. Finally, a Target Segmentation Block (TSB) is introduced to accurately segment the targets to produce the final detection result. Experiments on public datasets demonstrate that, compared to other methods, our model achieves high accuracy in segmenting targets while being able to extract false alarm sources which can be used for further studies.

Aromatic azo compounds have -N=N- double bonds as well as larger π electron conjugation system, which endows aromatic azo compounds with wide applications in the fields of functional materials. The properties of aromatic azo compounds are closely related to the substituents on their aromatic rings. However, traditional synthesis methods, such as the coupling of diazo salts, have a great limitation on the structural design of aromatic azo compounds. Therefore, many scientists have devoted their efforts to developing new synthetic methods. Moreover, recent advances in the synthesis of aromatic azo compounds led to the improvement of design and preparation of light-response materials at molecular level. This review summarizes the important synthetic progress of aromatic azo compounds in recent years, with an emphasis on the pioneering contribution of functional nanomaterials in the field.

The orthogonal matrix with cube be symmetric is a common class of matrices with important properties. We pay attention to this kind of matrices. By using the close relationship between the eigenvalues of a matrix and the trace of its power, we obtain the algorithm for its all possible different eigenvalues and multiplicities. The calculation formula is expressed only by the trace of a matrix and its power, avoiding solving the characteristic polynomial. The method is simple and practical. Furthermore, a new essential characterization for the sum of orthogonal matrix pairs being orthogonal is given as well.

We fabricated high-quality MAPbBr3 single crystals (SC) by introducing moderate amount electron-rich poly(propylene glycol bis(2-aminopropyl ether) (PEA) additives with an inverse temperature crystallization (ITC) method. The intramolecular vibrations and defective states of prepared MAPbBr3 single crystals were systemically studied by the in situ variable-temperature Fourier Transform Infrared (FTIR) Spectroscopy, X-ray photoelectron spectroscopy (XPS), and the synchrotron-based X-ray absorption near edge structure (XANES), et al. We infer that the proper amount of PEA additives would prevent the formation of intermediate states and crystal boundaries, passivating the density of defective states. The X-ray detection properties of single-crystal MAPbBr3 crystals were investigated, using both high dose and low dose X-ray photons at 40keV in synchrotron beamlines. The photocurrent of optimized PEA-treated MAPbBr3 single crystals demonstrate better performance compared with the as-prepared single crystals. Meanwhile, the decay time of MAPbBr3 single crystal is decreased from 460 ns to 210 ns by Time-resolved photoluminescence (TRPL) decay measurement, owing to the defect passivation by 0.5wt% PEA additives. The PEA-treated single crystals possess much faster decay time than the commercialized Ce:YAG scintillator (>500ns). These results help elucidate the passivation of defective states and contribute paths to manufacture high-quality single crystal perovskites for next-generation optoelectronic devices.

Mineral identification is an important part of geological analysis. Traditional identification methods rely on either the experiences of the appraisers or the various measuring instruments and the methods are either easily influenced by the experiences or need too much work. To solve the above problems, there have been studies using image recognition and intelligent algorithms to identify minerals. But the current studies can not identify many minerals, and the accuracy is low. To increase the number of identified mineral categories and the accuracy, we proposed the method that uses both the mineral images and the Mohs hardness in the deep neural networks to identify the minerals. The experimental results showed that the method can reach 94.0% Top-1 accuracy and 99.9% Top-5 accuracy for 28 common minerals. The model that combines image and Mohs hardness together can identify more minerals and increase the accuracy using less training data.

To obtain a cost-effective and high-performance composite material of polybutylene adipate-terephthalate (PBAT), for this study we selected microcrystalline cellulose, which is inexpensive and easily available, as the reinforcing medium. Hexadecyl trimethoxysilane (HDTMS) containing a long carbon chain was chosen to silanize the microcrystalline cellulose (MCC) to obtain silanized cellulose (SG). Three types of SGs with different degrees of silanization were obtained by controlling the reaction ratio. Characterization of these three types of SGs was conducted using FTIR, TEM, and water absorption analysis. Subsequently, PBAT/SG composites were prepared through a sol-gel method, and the effects of these three types of SGs on the thermal stability, compatibility, mechanical properties, and dynamic thermomechanical properties of PBAT were evaluated. Furthermore, the mechanism behind enhancing the mechanical properties of the composite was analyzed. The results demonstrated successful synthesis of SG. As the reaction ratio between HDTMS and MCC increased, the nanoparticle size increased, while the water absorption decreased significantly. After SG was added to the PBAT composites, the yield stress increased while maintaining good thermal stability. Both the SEM and DMA results indicated good compatibility of the PBAT/SG composites. Analysis of the mechanical properties revealed that the tensile strength initially increased and then decreased with increasing blending ratio for all three composites tested; among them, the PBAT/SG2 composites exhibit superior performance, with a maximum tensile strength reaching 22 MPa at an 85/15 blending ratio—nearly 30% higher than that of pure PBAT alone. The addition of SG significantly improved the strength of the PBAT, and we speculated as to the underlying mechanism involved. This study provides a new idea for the industrial-scale development of degradable polyesters with low cost and good mechanical properties.

In this work, an novel flow-electric field coupling configuration for enhanced Zn-Cd cementation was designed and utilized. A series of tests were conducted to explore the optimization of Zn-Cd cementation process and its mechanism.Firstly, the various characterisations of the cadmium sponge at different locations in the device were compared and it was concluded that the purity of the cadmium sponge was optimal from the anode surface. The generation and stripping of cadmium sponge was revealed for the first time by cross-sectional electron microscopy. The four stages of the apparent reaction in the system were analysed in relation to the pH, cadmium concentration and cadmium sponge flaking at each flow rate. It was proved that the separation of cadmium sponge mainly occurred in the third phase. Secondly, by comparing the morphology and specific surface area of cadmium sheep at different flow rates, the optimum flow field velocity was identified as 30 ml/s. Six flow field configurations were compared and preferred. The results demonstrate that the LCAH modulation results in a more sparse structure of the cadmium sponge, which is more easily exfoliated from the zinc anode surface by fluid impact. This was considered to be the most beneficial flow field configuration for improving the cadmium cementation rate and reducing the cost of the reaction. Further, the reaction steps of the system were analysed. The diffusion process under different flow field configurations was confirmed by calculations to follow first order kinetics. The diffusion coefficient of LACH proved to be the highest in the comparative tests and this result was also supported by the apparent experimental results.

Following the occurrence of a typhoon, quick damage assessment related to residents can facilitate quick dispatch of house repair and disaster insurance works. Employing a deep learning method, this study used aerial photos of the Chiba prefecture obtained following the Typhoon Faxai in 2019 to automatically detect and evaluate the roof damage. This study comprised three parts: training deep learning model, detecting the roof damage using trained model, and classifying the level of roof damage. The detection object comprised roof outline, blue tarps, and roof completely destroyed. The roofs were divided into three categories: roof without damage, roof with blue tarps and roof completely destroyed. the F value obtained using the proposed method was higher than those obtained using other methods. In addition, it can be further divided into 5 levels from level 0 to 4. Finally, the spatial distribution of the roof damage was analyzed using ArcGIS tools. The proposed method is expected to provide certain reference for the real-time detection of the roof damage after the occurrence of a typhoon.

Arylsulfatase and β-glucuronidase are two important enzymes in human, which play important role on dynamic equilibrium of steroidal estrogens. This work probably for the first time reported that hydrogen peroxide (H2O2), hypochlorite and peracetic acid (PAA) could effectively inhibit the activities of arylsulfatase and/or β-glucuronidase. The 50 percent of inhibitions (IC50) of H2O2, and PAA on arylsulfatase were found to be 142.90±9.00, 91.83±10.01, and 43.46±2.92 μM, respectively. The corresponding respective IC50 of hypochlorite and PAA on β-glucuronidase were 704.90±41.40 and 23.26±0.82 μM, while H2O2 showed no inhibition on β-glucuronidase. It was further revealed that the inhibition of hypochlorite on both arylsulfatase and β-glucuronidase was irreversible. On the contrary, the inhibition by H2O2 and PAA was reversible. Moreover, it was found that the inhibitions of arylsulfatase and/or β-glucuronidase by these three chemicals were pH-dependent, among which the inhibition by H2O2 was competitive and non-competitive for PAA. In general, H2O2 and hypochlorite can be endogenously produced in human, which suggested that the two compounds are potential endocrine disruption compounds (EDCs) as they can cause endocrine disruption via inhibition of arylsulfatase and β-glucuronidase. This work further indicated that any agent that can induce production of H2O2 or hypochlorite in human is potential EDC, which explains why some EDCs with very weak or no estrogenic potency can cause endocrine disruption that confirmed in epidemiological studies.

The migration paths and distribution driving factors of heavy metals in dry and windy area polluted by their production in the North China need a further research. To address this research gap, we collected 675 soil samples, 72 atmospheric deposition samples and 20 water samples around a production area and measured its heavy metal concentrations. Results showed that the Cu, Zn, As and Pb in 0-10 cm soil layer showed a fan-shaped distribution, which was consistent with their atmospheric deposition fluxes. It indicated the distribution patterns of these heavy metals were driven by strong winds in studied area. Although Cr concentrated to the production area in the 0-10 cm soil layer, principal component analysis showed that this migration was through wind as well. The concentration of Cd in the river increased from 0.257 mg/L to 0.460 mg/L along water flowing, and caused the same distribution trend in soil near the river from upstream to downstream. Unlike the above, surface runoff should drive the Cd migration. The concentration of Pb in the river was over threshold of pollution, and also led to an accumulation in the 5-10 cm soil layer. It suggested that the migration of Pb was through both wind and surface runoff. Six studied heavy metals showed different migration behaviors, and specific control strategies for individual heavy metal should be concerned.

The analysis of high-temperature physicochemical properties of theK₃AlF₆-Na₃AlF₆-AlF₃ molten salt system is crucial for practical production of electrolytic aluminum. In this paper, the physicochemical properties of the K₃AlF₆-Na₃AlF₆-AlF₃ molten salt electrolyte system at 1173 K and standard atmospheric pressure were simulated using molecular dynamics calculations. The effects of Zr、B、C、W、Ti、Hf、Nb、and Ta on the radial distribution function, coordination number, viscosity and conductivity of the electrolyte system are discussed in detail. The simulation results show that the coordination number between Al-F and the conductivity is decreasing as the content of B²- increases. And the coordination number between Al-F and the viscosity is decreasing as the content of Zr⁴⁺ increases. With the addition of impurity elements such as C, W, Ti, Hf, Nb, and Ta, the data show that C has no significant effect on this electrolyte system, while the presence of W will decrease the coordination number between Al-F in the system. The presence of Ti, Hf, Nb, and Ta may intensify the decomposition reaction between one of the Al-F ligands, which increases the coordination number between Al-F and the number of ions in the electrolyte. This work provides theoretical support for the subsequent study of inert anodes containing Zr, B, Ti, Hf, Nb, and Ta.

This research focussed on utilisation of salmon protein and lipid to manipulate pasta glycaemic index and protein digestibility. Salmon fish (Oncorhynchus tschawytscha) powder (SFP) supplemented pasta flour at the from 5% to 20% (w/w). Inclusion of SFP lead to a significant reduction in starch digestibility and hence the potential glycaemic values of pasta (experimental pasta being up to 143% lower than control values). SFP addition to pasta increased the release of phenolic compounds from pasta during both a gastric digestion (179%) and pancreatic digestion ( 133%) in comparison to the control sample. At the same time, the antioxidant activity of the digested pasta was increased by up to 263% (gastric) and 190% (pancreatic) in comparison to durum wheat pasta alone. Interestingly, although protein levels increased with incorporation of SFP, the digestibility values of the protein decreased from 86.41% for the control pasta to 81.95% for 20% SFP pasta. This may indicate that there are interactions between phenolic and protein in the pasta samples which affect overall protein digestibility levels.

Wearable touch sensors, which can convert force or pressure signals into quantitative electronic signals, have emerged as an essential smart sensing devices and played an important role in various cutting-edge fields, including wearable health monitoring, soft robots, electronic skin, artificial prosthetics, AR/VR, and the Internet of Things. Flexible touch sensors have made significant advancements, while construction of novel touch sensors via mimicking the unique properties of biological materials and biogenetic structures always remains a hot research topic and significant technological pathway. This review provides a comprehensive summary of the research status of wearable touch sensors constructed by imitating the material and structural characteristics in nature, and also summarizes the scientific challenges and development tendency of this aspect. Firstly, the research status for constructing flexible touch sensors based on biomimetic materials is summarized, including hydrogel materials, self-healing materials, and other bioinspired or biomimetic materials with extraordinary properties. Then, design and fabrication of flexible touch sensors based on bionic structures for performance enhancement are fully discussed. These bionic structures include special structures in plants, special structures insects/animal, and special structures in human body. Moreover, a summary of the current issues and future prospects for developing wearable sensors based on bioinspired materials and structures is discussed.

Currently the majority of studies on vision-based measurement has been conducted under ideal environments so that an adequate measurement performance and accuracy is ensured. However, vision-based systems may face some adverse influencing factors such as illumination change and fog interference, which can affect the measurement accuracy. This paper develops a robust vision-based displacement measurement method which can handle the two common and important adverse factors given above and achieve sensitivity at the subpixel level. The proposed method leverages the advantage of high-resolution imaging incorporating spatial and temporal context aspects. To validate the feasibility, stability and robustness of the proposed method, a series of experiments was conducted on a two-span three-lane bridge in the laboratory. The illumination change and fog interference are simulated experimentally in the laboratory. The results of the proposed method are compared to conventional displacement sensor data and current vision-based method results. It is demonstrated that the proposed method gives better measurement results than the current ones under illumination change and fog interference.

Air pollution has recently gained much attention from the general population. Despite pollution control being an issue in both urban and rural regions, most of the available research has concentrated on urban districts. Hence, investigations into how urban-rural transition affects PM2.5 are warranted within the framework of urban-rural integration. Using the Yellow River Basin as a case study, this study employed the entropy method and Analytic Hierarchy Process (AHP) to uncover the extent of urban-rural transformation. It then used the spatial autocorrelation method to investigate the spatiotemporal features of PM2.5 and the spatial econometric model to investigate the mechanisms that influence the relationship between urban-rural transformation and PM2.5. The results are as follows: (1) Over time, there was a discernible upward tendency in the change in urban-rural areas. The development has progressed from asymmetrical north-east and south-west elevations to a more balanced pattern of north-east, middle-east, and west-west elevations. (2) The PM2.5 concentration increased steadily, then fluctuated, and finally decreased. Notably, the general pattern has not changed much, and it is high in the east and low in the west. (3) Different subsystems of the urban-rural transformation have different impacts on air pollution at different stages. The influence of industrial transformation (IT) on PM2.5 showed an inverted “N-shaped” curve of negative-positive-negative changes, and the industrial structure played a leading role in the spatiotemporal evolution of PM2.5. Currently, an inverted "U-shaped" curve forms the left side of the impact of population transition (PT) on PM2.5. Land development (LT) has a "U-shaped" curve for its effect on PM2.5. This research provides a new perspective on the topic of PM2.5 and its connection to urban-rural integration, which is crucial to understanding the dynamics of this shift. To achieve its goal of high-quality development, it supports regional initiatives to reduce PM2.5 emissions in the Yellow River Basin. Moreover, it can provide a reference for decision-makers in the world’s densely populated areas that suffer from serious air pollution.

Real-time object detection remains a pivotal topic in the realm of computer vision. Balancing the accuracy and speed of object detectors poses a formidable challenge for both academic researchers and industry practitioners. While recent transformer-based models have showncase the prowess of the attention mechanism, delivering remarkable performance improvements over CNNs, their computational demands can hinder their effectiveness in real-time detection tasks. In this paper, we elect to use YOLOX as our robust starting point and introduce a series of effective enhancements, culminating in a new high-performance detector named YOLOAX. To further exploit the power of the attention mechanism, we devise multi-dimensional attention-based modules that activate CNNs, emphasizing the most pertinent regions and bolstering the capacity to learn the most informative image representations from feature maps. Moreover, we introduce a novel leading label assignment strategy called STA, along with a groundbreaking loss function named GEIOU Loss, to further refine our detector's performance. We provide extensive ablation studies on the COCO and PASCAL VOC 2012 detection datasets to validate our proposed methods. Remarkably, our YOLOAX is trained solely on the MS-COCO dataset from scratch, without leveraging any prior knowledge, which achieves an impressive 54.2% AP on the COCO 2017 test set while maintaining a real-time speed of 72.3 fps, surpassing YOLOX by a significant margin of 3.0% AP. Our source code and pre-trained models are openly accessible at https://github.com/KejianXu/yoloax.

Aiming to investigate the impact of strategic knowledge disclosure on the continuous realization of digital innovation in enterprises, this study examines data from 168 listed companies across three high-tech industries in China from 2012 to 2021. By examining investor trust, consumer trust, worker trust, and rival trust as mediating variables within the market trust dimension, this research explores the impact mechanism of strategic knowledge disclosure on the sustainability of input and output in digital innovation. The findings reveal that strategic knowledge disclosure significantly promotes both input and output sustainability in digital innovation. Specifically, investor trust positively mediates the relationship between strategic knowledge disclosure and the sustainability of digital innovation input. Similarly, consumer trust and worker trust positively mediate the association between strategic knowledge disclosure and both input and output sustainability in digital innovation. However, it is important to note that rival trust negatively mediates the link between strategic knowledge disclosure and both input and output sustainability in digital innovation. The research findings possess significant theoretical value and provide valuable guidance for promoting the sustainable development of digital innovation in enterprises.

As one of the common techniques for measuring coseismic deformations, optical image correlation techniques are capable of overcoming the drawbacks of inadequate coherence and phase blurring which can occur in radar interferometry, as well as the problem of low spatial resolution in radar pixel offset tracking. However, the scales of the correlation window in optical image correlation techniques typically influence the results, the conventional SAR POT method faces a fundamental trade-off between the accuracy of matching and the preservation of details in the matching window size. This study regards co-seismic deformation as a two-dimensional vector, and develops a new post-processing workflow called VACI-OIC to reduce the dependence of shift estimation on the size of the matching window. This paper takes the coseismic deformations in both the east-west and north-south directions into account at the same time, treating them as vectors, while also considering the similarity of displacement between adjacent points on the surface. Herein, the angular continuity index of the coseismic deformation vector was proposed as a more reasonable constraint condition to fuse the deformation field results obtained by optical image correlation across different matching window. Taking the earthquake of 2021 in Maduo, China, as the study area, the deformation with the highest spatial resolution in the violent surface rupture area was determined (which could not be provided by SAR data). Compared to the results of single-scale optical correlation, the presented results were more uniform (i.e., more consistent with published results). At the same time, the proposed index also detected the strip fracture zone of the earthquake with impressive clarity.

Epilepsy is characterized by repeated spontaneous reactions caused by hyper-excitability and neurons firing in high synchronization in the central nervous system. It seriously affects the quality of life of epileptic patients and nearly 30% of individuals are refractory to treatment of antiepileptic drugs. Therefore, there is an urgent need to develop new medicines to manage and control the refractory epilepsy. Cannabinoid ligands including selective cannabinoid receptor subtype (CB1 or CB2 receptor) ligands and non-selective cannabinoid (synthetic and endogenous) ligands may serve as the novel candidates for this need. Cannabinoid systems appear to regulating seizure activity in the brain through the activation of CB1 and CB2 cannabinoid receptors (CB1R and CB2R). An abundant series of cannabinoid analogues have been tested in various animal models, including a rat pilocarpine model of acquired epilepsy, in vitro hippocampal neuronal culture models of acquired epilepsy and status epilepticus, a pentylenetetrazole model of myoclonic seizures in mice and a penicillin-induced model of epileptiform activity in the rats. The accumulating lines of evidence show that cannabinoid ligands exhibit significant benefits to control seizure activity in different epileptic models. For this reason, we summarize the relationship between brain CB2 receptors and seizures, and emphasize the potential mechanisms of their therapeutic effects involving affecting neurons, astrocytes, and microglia cells. The unique features of CB2Rs, such as lower expression levels under physiological conditions and high inducibility under epileptic conditions, make it an important target for future research on drug-resistant epilepsy.

Hand and arm gesture recognition using radio frequency (RF) sensing modality proves valuable in man-machine interface and smart environment. In this paper, we use time series analysis method for accurately measuring the similarity of the micro-Doppler (MD) signatures between the training and test data, thus providing improved gesture classification. We characterize the MD signatures by the maximum instantaneous Doppler frequencies depicted in the spectrograms. In particular, we apply the dynamic time warping (DTW) method and compare its performance with that of the long short-term memory (LSTM) network. Both methods take into account the values as well as the temporal evolution and trends of time series data. It is shown that the DTW method achieves high gesture classification rates and is robust to time misalignment.

List-only entity linking is the task of mapping ambiguous mentions in texts to target entities in a group of entity lists. Different from traditional entity linking task, which leverages rich semantic relatedness in knowledge bases to improve linking accuracy, list-only entity linking can merely take advantage of co-occurrences information in entity lists. State-of-the-art work utilizes co-occurrences information to enrich entity descriptions, which are further used to calculate local compatibility between mentions and entities to determine results. Nonetheless, entity coherence is also deemed to play an important part in entity linking, which is yet currently neglected. In this work, in addition to local compatibility, we take into account global coherence among entities. Specifically, we propose to harness co-occurrences in entity lists for mining both explicit and implicit entity relations. The relations are then integrated into an entity graph, on which Personalized PageRank is incorporated to compute entity coherence. The final results are derived by combining local mention-entity similarity and global entity coherence. The experimental studies validate the superiority of our method. Our proposal not only improves the performance of list-only entity linking, but also opens up the bridge between list-only entity linking and conventional entity linking solutions.

Here, we present a series of novel block copolymers (BCP) from bio-derived monomers, poly(lactic acid)-block-poly(2,5-furandimethylene succinate) (PLA-b-PFS), in which the furan groups from PFS block can be crosslinked with bis(maleimido) triethylene glycol (M2) through a Diels-Alder reaction. This dynamic crosslinking reaction leads to a network structure for enhancing the mechanical properties compared to their linear BCP analogous. Decreasing the crosslinking density leads to a decrease of glass transition temperature of BCPs and a transition from glassy to rubbery-like behavior at room temperature. This allows a wide tunablity of both elastic moduli and yields of the materials. For the lowest crosslinking density. the material exhibits an over 50% self-healing efficiency at room temperature after five days, attributed to the low Tg (15.2 C) from the introduction of PFS block, allowing sufficient chain mobility for structure re-organization. Moreover, with the appropriate selection of crosslinking density (PLA-b-PFS/M2 (6/1)), it also shows an excellent shape memory property with a high recovery rate of 96.3% and a fixity rate of 97.3%. The permanent shape can be rewriteable due to the reversibility of Diels-Alder reaction. With these advanced functionalities and ease in large-scale fabrication, the PLA-b-PFS/M2 shows great promises for self-healing coatings or films with shape memory properties in a wide variety of applications such as packaging materials

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

Connected and Autonomous Vehicle (CAV) combines technologies of autonomous vehicle (AV) and connected vehicles (CV) to develop quicker, more reliable and safer traffic. Artificial Intelligence (AI) based CAV solutions play significant roles in sustainable city. The convergence imposes stringent security requirements for CAV safety and reliability. In practice, vehicles are developed with increased automation and connectivity. Increased automation increases the reliance on the sensor-based technologies and decreases the reliance on driver; increased connectivity increases the exposures of vehicles vulnerability and increases the risk for an adversary to implement a cyber-attack. Much work has been dedicated to identifying the security vulnerabilities and recommending mitigation techniques associated with different sensors, controllers, and connection mechanisms, respectively. However, there is an absence of comprehensive and in-depth studies to identify how the cyber-attacks exploit the vehicles vulnerabilities to negatively impact the performance and operations of CAV. In this survey, we set out to thoroughly review the security issues introduced by AV and CV technologies, analyze how the cyber-attacks impact the performance of CAV, and summarize the solutions correspondingly. The impact of cyber-attacks on the performance of CAV is elaborated from both viewpoints of intra-vehicle system and inter-vehicle system. We pointed out that securing the perception and operations of CAV would be the top requirement to enable CAV to be applied safely and reliably in practice. Also, we suggested to utilize cloud and new AI methods to defend against smart cyber-attacks on CAV.

Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

Artificial intelligence provides a new research concept for digital image processing. However, at present, artificial intelligence is rarely introduced into the teaching of digital image processing in colleges and universities, and there are problems such as obsolete teaching content, single teaching methods, and simple course experiments, which affect the teaching effect and are not conducive to the cultivation of comprehensive and innovative talents. Digital image processing technology brings more possibilities to communication engineering and makes communication more convenient. For example, video calls and photo transmission make people's communication methods in daily life more and more diversified. Time and space limitations allow people to meet online, creating more communication possibilities. However, there are still many problems and methods worthy of in-depth exploration. Therefore, this paper has a comprehensive understanding and mastery of the traditional and deep learning methods of digital image processing to improve the relevant project practice and scientific research exploration ability and refer for similar research conclusions.

In order to study the crystallinity of different density polyethylenes, the experimental study on the transformation of the conductance mechanism under high electric field was carried out. The X-ray Diffraction(XRD), Different Scanning Calorimeter(DSC), Direct Current(DC) breakdown of Low-density polyethylene(LDPE), Linear low density polyethylene(LLDPE), Medium density polyethylene(MDPE) and High-density polyethylene(HDPE) and the electric field of 5-200kV/mm were tested. Conductivity characteristics experiments, in addition, using the mathematical formula of a variety of conductance mechanisms, the electric field-current density curves of the four kinds of polyethylene were fitted to analyze the conductance transition of the above four kinds of polyethylene in non-ohmic regions under different high field strengths. mechanism. The experimental results show that as the density of polyethylene increases, the crystallinity increases continuously, and the continuous increase of crystallinity causes the electric conduction flow under the same field strength to decrease significantly. The field strength corresponding to the two turning points in the conductance characteristic curve increases simultaneously. Large, the breakdown field strength increases; through analysis, it is found that in the high field, as the electric field increases, the conductance mechanism develops from the ohmic conductance of the low field strength region to the bulk effect of the high field strength region (Poole-Frenkel). Then the electrode effect to the high field strength (Schottky), and the threshold field strength of this conductance mechanism transition increases with the increase of crystallinity.

The deployment of a manufacturing execution system (MES) holds promising potential in facilitating the accumulation of a substantial amount of inspection data. Low quality levels in discrete manufacturing environments are the result of multi-factor coupling and failure to find quality issues in a timely manner within manufacturing settings may trigger the propagation of defects downstream. Currently, most of the inspection quality methods are direct measurement followed by manual judgment. The integration of deep learning methods provides a feasible way to identify defects in a timely manner, thus improving the acceptance rate of factories. This paper focuses on the design of a data-driven quality prediction and control model around discrete manufacturing characteristics, and use fuzzy theory to evaluate the quality level of production stages. Building Multivariate Long and short-term memory learning hidden quality representations to extract predictions from multi-level inspection data in manufacturing systems. Finally, by validating the data of actual produced water dispensers according to three evaluation indexes, RMSE, MAE, MAPE, the results show that Multivariate Long and short-term memory has better prediction performance.

Avian infectious bronchitis virus (IBV) is the causative agent of infectious bronchitis, which causes considerable economic losses to the poultry industry worldwide. It is imperative to develop safe and efficient candidate vaccines to control IBV infection. In the current study, recombinant baculoviruses co-expressing S1 and N proteins, mono-expressing S1 or N proteins alone of IBV were constructed and prepared into subunit vaccines rHBM-S1-N, rHBM-S1 and rHBM-N. The levels of immune protection of these subunit vaccines were evaluated by inoculating specific pathogen-free (SPF) chickens at 14 days of age, boosting with the same dose 14 days later, and following challenge with a virulent GX-YL5 strain of IBV 14 days post-booster (dpb). The commercial vaccine strain H120 was used as a control. The IBV-specific antibody levels as well as the percentages of CD4+ and CD8+ T lymphocytes were detected within 28 days post-vaccination (dpv). The morbidity, mortality, and re-isolation of virus from the tracheas and kidneys of challenged birds were evaluated at 5 days post-challenge (dpc). The results showed that the IBV-specific antibody levels and the percentages of CD4+ and CD8+ T lymphocyte in rHBM-S1-N group were higher than those of rHBM-S1 and rHBM-N groups, especially the cellular immunity response. At 5 dpc, the mortality, morbidity and virus re-isolation rate of rHBM-S1-N were slightly higher than those of H120 group, but were lower than those of rHBM-S1 group and rHBM-N group. The present study demonstrated that the protection of recombinant baculovirus co-expressing S1 and N proteins was better than that of recombinant baculoviruses mono-expressing S1 or N protein alone. Thus, the recombinant baculovirus co-expressing S1 and N proteins could serve as a potential IBV vaccine and this demonstrates that the bivalent subunit vaccine including the S1 and N proteins might be a strategy for the development of an IBV subunit vaccine.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

Bovine respiratory disease (BRD) is the leading cause of morbidity and mortality in cattle raised in North America. At the feedlot, cattle are subject to metaphylactic treatment with macrolides to prevent BRD, a practice that may promote antimicrobial resistance and has resulted in an urgent need for novel strategies. Mannheimia haemolytica is one of the major bacterial agents of BRD. The inhibitory effects of two amphipathic, α-helical (PRW4, WRL3) and one β-sheet (WK2) antimicrobial peptides were evaluated against multidrug-resistant (MDR) M. haemolytica isolated from Alberta feedlots. WK2 was not cytotoxic against bovine turbinate (BT) cells by the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay. All three peptides inhibited M. haemolytica, with WK2, being the most efficacious against multiple isolates. At 8-16 µg/ml, WK2 was bactericidal against Mh 330 in broth and at 32 µg/ml in the presence of BT cells, reduced the population by 3 logs CFU/ml without causing cytotoxic effects. The membrane integrity of Mh 330 was examined using NPN (1-N-phenylnaphthylamine), and ONPG (o-Nitrophenyl β-D-galactopyranoside) with both the inner and outer membranes being compromised. Thus, WK2 may be a viable alternative to the use of macrolides as part of BRD prevention and treatment strategies.

Based on the analysis of the spatial distribution of uranium grade in 348 boreholes of a uranium deposit in Xinjiang, the enrichment and spatial variation of uranium ore in two stopes of the deposit are discussed by using multifractal theory. The distribution characteristics of uranium ore of the two stopes are studied by multifractal parameters: the scaling exponent of mass , the scaling exponent of each sub-set and its corresponding fractal dimension , the fractal dimension D0 and information dimension D1. The differences of uranium distribution in two stopes can be well quantified by multifractal spectrum and multifractal parameters( , , ).10m×10m is defined as a fence unit, and the window sizes are respectively set, the singularity exponent of the two stopes are calculated by this element concentration-area(C-A) method. The results show that the multifractal theory and model can organically combine spatial structure information, scale change information and anisotropy information to obtain low-grade and weak mineral resources information, and can effectively distinguish complex and superimposed anomalies. This will provide a basis for local concentration and spatial variation rules of uranium distribution and the design of the parameters of leaching uranium mining well site.

Urban vitality is an important reflection of a city's development potential and urban quality. This study uses exploratory spatio-temporal big data such as social media check-ins to portray the spatio-temporal evolution of urban vitality at the subdistrict scale in Changsha, a city in central China, from 2013-2021, and finds that urban vitality in Changsha exhibits central agglomeration and outward circling expansion over time; and then use Geodetector and spatial regression analyses are used to explain the interactive effects and spatio-temporal heterogeneity of the spa-tial elements of subdistrict form, subdistrict function and subdistrict economy on urban vi-tality. The results show the following: (1) The subdistrict form and subdistrict function dimen-sions have a significant effect on urban vitality, and the effect of the economic dimension of the subdistrict is not significant. (2) The interaction effect of the density of entertainment and leisure facilities and the density of business office facilities in subdistrict function is the dominant factor in the change of urban vitality. (3) Under the spatio-temporal effect, land use diversity and park facility density have the strongest positive effect on urban vitality; road density and shopping facility density have the weakest effect. The study aims to provide a reference for the optimization and allocation of spatial elements of subdistricts in sustainable urban development and urban renewal, to achieve the purpose of urban vitality creation and enhancement.

Density functional theory (DFT) and coupled cluster theory (CCSD(T)) calculations are performed to investigate the geometric, electronic structures and chemical bonding of a series of Cu-doped zinc oxide clusters, CunZn3O3 (n = 1-4). The structural evolution of CunZn3O3 (n = 1-4) clusters are elaborated in our work. The planar seven-membered ring of CuZn3O3 cluster plays an important role in the structural evolution, that is, the Cu atom, Cu dimer (Cu2) and Cu trimer (Cu3) anchor on the CuZn3O3 cluster. The aggregate behavior of Cu atoms on Zn3O3 may offer insight into the study of Cu/ZnO-based catalysts. Additionally, it is found that the CunZn3O3 clusters become more stable as the Cu content (n) increases. Bader charge analysis points out that as the Cu atoms doping, the reducibility of Cu aggregation (Cun-1) on the CuZn3O3 cluster increases. Combined with the d-band centers and the surface electrostatic potential (ESP), the reactivity and the possible reaction sites of CunZn3O3 (n = 1-4) clusters are also illustrated.