In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

Some traditional robots are based on offline programming reciprocal motion, and with the continuous upgrading of vision technology, more and more tasks are replaced by machine vision. For the current problem of insufficient accuracy of robot target localization based on binocular vision, and an improved random sampling consistency algorithm is proposed to complete parallel robot target localization and grasping under the guidance For the current problem of insufficient accuracy of robot target localization based on binocular vision, an improved random sampling consistency algorithm is proposed to complete parallel robot target localization and grasping under the guidance of multi Firstly, the RANSAC algorithm is improved based on the SURF algorithm; then the parallax gradient method is applied to iterate the matched point pairs several times to further optimize the data; then the 3D reconstruction is completed by the program technique; finally the obtained data is finally the obtained data is input into the robot arm and the camera internal and external parameters are obtained by the calibration method so that the robot can accurately locate and The experiments show that the improved algorithm has advantages in recognition accuracy and grasping success rate under multi- The experiments show that the improved algorithm has advantages in recognition accuracy and grasping success rate under multi-vision system.

Discrete distribution estimation is a fundamental statistical tool, which is widely used to perform data analysis tasks in various applications involving sensitive personal information. Due to privacy concerns, individuals may not always provide their raw information, which leads to unpredictable biases in the final results of estimated distribution. Local Differential Privacy (LDP) is an advanced technique for privacy protection of discrete distribution estimation. Currently, typical LDP mechanisms provide same protection for all items in the domain, which imposes unnecessary perturbation on less sensitive items and thus degrades the utility of final results. Although, several recent works try to alleviate this problem, the utility can be further improved. In this paper, we propose a novel notion called Item-Oriented Personalized LDP (IPLDP), which independently perturbs different items with different privacy budgets to achieve personalized privacy protection. Furthermore, to satisfy IPLDP, we propose the Item-Oriented Personalized Randomized Response (IPRR) based on the observation that the sensitivity of data shows an inverse relationship with the population size of respective individuals. Theoretical analysis and experimental results demonstrate that our method can provide fine-grained privacy protection and improve data utility simultaneously.

The construction of large-scale water diversion projects alleviated effectively the current situa-tion of uneven distribution of water resources in China. However, due to the siltation of very fine sediment and organic matter on the side wall of the open channel, and the slow velocity of the side wall flow field, it is easy to produce epipelic algae, which affects water quality. For the prototype observation cannot be used to predict the series of flow in real time, and the mathe-matical model calculation is affected by parameter limitations, these two methods often cannot truly reflect the hydrodynamic characteristics of open channel with epipelic algae. Therefore, by referring to the design parameters of the water diversion project channel, this paper takes the epipelic algae growing on the side wall of the open channel as the research object, and uses the scale of 1:30 to carry out the generalized flume experiment. Through the analysis of the physical characteristics of the prototype sample, and the simulation of the cohesive force between the oblique side wall and the epipelic algae, the multi-group and multi-series hydrodynamic tests are carried out. The flow velocity distribution law and the development and change of the tur-bulent vortex on the side wall are analyzed. It has important scientific guiding significance and practical value for water quantity regulation water regulation and water quality safety protec-tion of long-distance projects.

Propolis was widely used in health preservation and disease healing, it contains many ingredients. The previous study had been revealed that the propolis has a wide range of efficacy, such as antiviral, immune enhancement, anti-inflammatory and so on, but its antiviral components and underlying mechanism of action remain unknown. In this study, we investigated the chemical composition, and anti-PPV and immunological enhancement of Propolis Flavonoid(PF). Chemical composition of PF was distinguished by UPLC-Q/TOF-MS/MS analysis.The presence and characterized of 26 major components was distinguished in negative ionization modes.To evaluate the effects of PF used as adjuvant on the immune response porcine parvovirus (PPV). Thirty Landrace-Yorkshire hybrid sows were randomly assigned to 3 groups, and the sows in adjuvant groups were intramuscular injected PPV vaccine with 2.0 mL PF adjuvant (PA), oilemulsion adjuvant (OA), respectively. After that, serum hemagglutination inhibition antibody titers, IgM and IgG subclasses, eripheral lymphocyte proliferation activity, and concentrations of cytokines were measured. Results indicated an enhancing effect of PA on IgM, IL-2, IL-4, IFN-γ and the IgG subclass responses. These findings suggested that PA could significantly enhance the immune responses. Furthermore, we screened the chemical components the effective of anti-PPV, Ferulic acid have an excellently anti-PPV effective.

Signal-to-noise ratio (SNR) is an important index to evaluate radiation performance and image quality of optical imaging systems under low illumination background. Under the nighttime lighting condition, the illumination of remote sensing objects is low and varies greatly, usually ranging from several lux to tens of thousands of lux. Nighttime light remote sensing imaging requires high sensitivity and large dynamic range of detectors. Luojia 1-01 is the first professional nighttime light remote sensing satellite in the world. In this paper, we took the nighttime light remote sensing camera carried on the satellite as research object, proposed an in-orbit SNR test method based on time series images to overcome the problem of low spatial resolution. We first analyzed the process of luminous flux transmission between objects and satellite and established a radiative transfer model. By combining the parameters of large relative aperture optical system and high sensitivity CMOS device, we established SNR model and specially analyzed the effect of exposure time and quantization bits on SNR. Finally we used the proposed in-orbit test method to calculate SNR of lighting images acquired by satellite. And the measured result is in good agreement with the model predicted data. Under the condition of 10lx illumination, the SNR of typical objects can reach 27.02dB, which is much better than the requirement of 20dB for engineering application.

The ridge-furrow plastic mulching (RFPM) system and nitrogen application have been effective strategies for improving crop productivity in the Loess Plateau of China. However, it is not clear how the ridge-furrow ratio and nitrogen fertilizer type (NT) affect the utilization of water, nitrogen, heat and radiation resources for increased rain-fed wheat production. Two nitrogen fertilizer types [Traditional urea (TU) and controlled-release urea (CRU)] and four planting patterns [conventional flat planting (F) and the RFPM system of 20 cm ridge with 40 cm furrow (R2F4), 40 cm ridge with 40 cm furrow (R4F4), and 60 cm ridge with 40 cm furrow (R6F4)] were tested from September, 2018 to June, 2021 during winter wheat growing season. The results showed that the RFPM system can increase the soil thermal time (TTsoil) by 41.0–152.1°C d compared to F. The thermal effect of the RFPM system shortens the vegetative growth period and extends the reproductive growth period by 2–7 days, promoting the increase of the leaf area index (LAI) and final dry matter (DM) accumulation. These significantly increased the grain yield (GY) in the RFPM system by 51.6–115.2% and enhanced the thermal time use efficiency (TUE) by 48–99.5%, water productivity (WP) by 37.4–76.3%, radiation use efficiency (RUE) by 16.3–34.4%, and partial factor productivity of nitrogen (PFPN) by 51.6–115.2% compared to F. Although a high ridge-furrow ratio combined with CRU increased GY and resources use efficiency, it also exacerbated the soil water depletion, especially in the 40–140 cm soil layer. Overall, applying CRU in combination with the RFPM system of 40 cm ridge with 40 cm furrow maximized resources use efficiency and increased wheat production in the Loess Plateau of China.

Strong-aroma Baijiu is a traditional Chinese spirit distilled from grains that undergo solid-state fermentation. At the end of each fermentation cycle, a significant quantity of Huangshui accumulates at the bottom of the fermentation pit, constituting one of the primary by-products in the brewing process of strong-flavor liquor. In this report, the chemical component analysis of Huangshui obtained from a strong-flavor liquor factory revealed a diverse array of organic acids, alcohols, esters, starch, reducing sugars, amino acids, and other compounds present in Huangshui. Additionally, two specialized solid-state fermentation models were developed to investigate the formation process of Huangshui. Our findings demonstrate a positive correlation between the yield of Huangshui and the initial moisture content of fermented grains. It is concluded that Huangshui is the percolate produced during the solid-state brewing process of strong-flavor liquor, with its water content originating from the initial moisture of fermented grains.

Surgical methods for treating spasmodic torticollis include denervation and myotomy (DAM) of the affected muscles, and deep brain stimulation (DBS). This study reports on the long-term efficacy, prognostic factors, safety, and hospitalization costs following these two procedures. We collected data from 94 patients with spasmodic torticollis, of whom 41 and 53 were treated with DAM and DBS, respectively, from June 2008 to December 2020 at the Chinese People’s Liberation Army General Hospital. We used the Tsui scale and the global outcome score of the Toronto Western Spasmodic Torticollis Rating Scale (TWSTRS) to evaluate the preoperative and postoperative clinical condition in all patients. We also determined the cost of hospitalization, prognostic factors, and serious adverse events following the two surgical procedures. The mean follow-up time was 68.83 months (range = 13–116). Both resection surgery and DBS showed good results in terms of Tsui (Z = -5.103, P = 0.000; Z = -6.210, P = 0.000) and TWSTRS scores (t = 8.762, P = 0.000; Z = -6.308, P = 0.000). Compared with the DAM group, the preoperative (47.71, range 24–67.25) and postoperative (18.57, range 0–53) TWSTRS scores in the DBS group were significantly higher (Z = -3.161, P = 0.002). We found no correlation between prognostic factors and the patient age, gender, or disease duration for either surgical procedure. However, prognostic factors were related to the length of the postoperative follow-up period in the DBS surgery group (Z = -2.068, P = 0.039; Z = -3.287, P = 0.001). The mean hospitalization cost in the DBS group was 6.85 times that found in the resection group (Z = -8.284, P = 0.000). The total complication rate was 4.26%. We found, both resection surgery and DBS, showed good results in the patients with spasmodic torticollis. Although DBS had a greater impact on the quality of life and the degree of pain relief, it was more expensive. Prognostic factors were related to the length of the postoperative follow-up period in patients who underwent DBS surgery.

Acanthamoeba keratitis (AK) is a blinding corneal infection caused by the protozoan Acanthamoeba. The long-term course of AK suggests the host immunity could not kill Acanthamoeba rapidly. The immune status is still unclear in the late stage of AK. The comparative transcriptome analysis was made based on the bulk RNA sequencing of cornea tissues from AK patients and donors. Differentially expressed genes and enriched signaling pathways were calculated. CIBERSORT algorithm was used for Immune infiltration analysis of cornea tissue between AK and normal controls. A total of 2668 differentially expressed genes, including 1477 upregulated genes and 1191 downregulated genes, were detected. Gene Ontology analysis revealed that the pathways were significantly enriched in leukocyte migration, regulation of T cell activation, the external side of plasma membrane, collagen-containing extracellular matrix, immune receptor activity and cytokine binding. KEGG pathway analysis showed that the pathways were significantly enriched in the cytokine-cytokine receptor interaction, hematopoietic cell lineage and Staphylococcus aureus infection pathway. The immune infiltration profiles varied little between AK and normal controls. Compared with normal tissue, cornea tissue of AK contained a higher proportion of M0 macrophages and CD8 T cells, while resting memory CD4 T cells contributed to a relatively lower portion (P < 0.05). Finally, the expression levels of cell markers and SLAMF7/STAT6 pathway were confirmed by histopathology examinations, RT-qPCR and western blot.

As the application of cyber-physical systems (CPSs) becomes more and more widespread, its security is becoming a focus of attention. Currently, there has been much research on the security defense of the physical layer of the CPS. However, most of the research only focuses on one of the aspects, for example, attack detection, security state estimation or recovery control. Obviously, the effectiveness of security defense targeting only one aspect is limited. Therefore, in this paper, a set of security defense processes is proposed for the case that a CPS containing multiple sensors is subject to three kinds of stealthy attacks (i.e., zero-dynamics attack, covert attack, and replay attack). Firstly, the existing attack detection method based on improved residuals is used to detect stealthy attacks. Secondly, based on the detection results, an optimal state estimation method based on improved Kalman filtering is proposed to estimate the actual state of the system. Then, based on the optimal state, internal model control (IMC) is introduced to complete the recovery control of the system. Finally, the proposed methods are integrated to give a complete security defense process, and the simulation is verified for three kinds of stealthy attacks. The simulation results show that the proposed methods are effective.

Abstract Background: Parkinson's disease (PD) is a neurodegenerative disorder featured with motor and non-motor deficits. Using 1-methyl-4-phenyl-1,2,3,6-tetrahydropyridine (MPTP) induced dopamine neuron degeneration has been widely used to produce reliable animal models of the PD. However, most of previous preclinical studies focused on the motor dysfunctions, few non-motor symptoms were evaluated. So far there is a lack of comprehensive investigation of the non-motor symptoms in animal models. Objectives: In this study, we aim to use a battery of behavioral methods to evaluate the non-motor symptoms in MPTP-induced non-human primate PD models. Methods: Cognitive functions, sleep and psychiatric behaviors were evaluated in MPTP-treated cynomolgus monkeys. The tests consisted of delayed matching-to-sample (DMTS), physical activity monitor (PAM), apathy feeding task (AFT), human intruder test (HIT), novel fruit test (NFT) and predator confrontation test (PCT). In addition, we tested whether the dopamine receptor agonist pramipexole (PPX) will improve these non-motor symptoms. Results: The present results show that the MPTP-treated monkeys exhibited cognitive deficits, abnormal sleep, and anxiety-like behaviors as compared to the control monkeys. These symptoms were relieved partially by PPX. Conclusions: These results suggest that MPTP-induced PD monkeys displayed non-motor symptoms that were similar to those found in PD patients. PPX treatment showed moderate therapeutic effects on these non-motor symptoms. This battery of behavioral tests may provide a valuable model for future preclinical research.

Lactic acid (LA) is a significant byproduct in Baijiu fermentation, with both D(-)-lactic acid (D(-)-LA) and L-lactic acid (L(+)-LA) being present due to the diverse microbial metabolism involved. L(+)-LA, a key industrial raw material, is metabolizable by humans, unlike D(-)-LA. This study aims to isolate microorganisms from fermented grains that preferentially produce L(+)-LA and apply these strains to Baijiu fermentation processes. We analyzed 106 commercially available Baijiu samples, along with fermented grains, yellow water, and Baijiu samples from 10 Baijiu factories, confirming the coexistence of D(-)-LA and L(+)-LA in fermentation products. Notably, a strong correlation was found between L(+)-LA in fermented grains and L-ethyl lactate (L(+)-EL) in Baijiu. Microbial community analysis revealed that Lactobacillus and Bacillus were the dominant bacterial groups, with a succession of microbial communities throughout fermentation. Two strains, A6 and B12, identified as Bacillus licheniformis and Bacillus cereus, respectively, were isolated for their high selectivity in L(+)-LA production. Both strains demonstrated a high yield of L(+)-LA in fermentation tests. Incorporating these strains into both liquid- and solid-state fermentation systems markedly increased the proportion of L(+)-EL relative to total ethyl lactate in Baijiu. This study successfully isolated and applied L(+)-LA-producing strains to fermentation models, offering a practical strategy for increasing L(+)-LA content in Baijiu.

Species have shown their habital variations in responding to climate change, especially during the spring and summer spawning seasons. The species distribution model (SDM) is considered the most favorable tool to study the potential effects of climate change on species distribution. Therefore, we developed the ensemble SDM to predict the changes in species distribution of Portunus trituberculatus among different seasons in 2050 and 2100 under the climate scenarios RCP4.5 and RCP8.5. The results of SDM indicate that the distribution of this species will move northward and have obviouse seasonal variations. Meanwhile, the suitable habitat for the species will be significantly reduced in summer, with loses rates ranging from 45.23% (RCP4.5) to 88.26% (RCP.8.5) by 2100s. Habitat reduction will mainly occur in the East China Sea and southern part of the Yellow Sea, while there will be a small increase in the northern Bohai Sea. These findings will be important to manage the ecosystem and fishery, provide an information forecast of this species in the future, and maintain species diversity if the seawater temperature rises.

To determine the metamorphic ages of the accretionary complexes in the Northern Chichibu Belt in SW Japan, K–Ar dating was conducted using weakly metamorphosed sedimentary rocks collected from the Kanto Mountains, Central Japan. Whole-rock ages were obtained for chert and red shale samples, and the mineral ages of fine-grained illite with the grain size less than 4 μm were obtained for chert, red shale, mudstone, acidic tuff, and basic tuff. The K–Ar ages of chert and red shale presented large variations, with systematically older ages compared to those of mudstone and tuff in the same strata. The influence of submarine hydrothermal activities on chert and red shale before subduction is a possible cause of this deviation. The illite samples, which were fractionated into four grain-size classes using a suspension method, yielded older ages and higher illite crystallinity (i.e., smaller values of Kübler’s crystallinity index) for larger grain-size classes. The peak metamorphic ages were determined from the K–Ar ages of the 3–4 μm class illite in mudstone and tuff. The Late Jurassic to the Earliest Cretaceous accretionary complex of the lowest structural unit (Kashiwagi Unit) was dated within a small range between 117–110 Ma, which is distinctly older than the K–Ar ages of white mica reported from the Sanbagawa Belt. The peak metamorphic age of acidic tuff (113 Ma) at the type locality of the Mikabu Greenstones indicates that the subducted Mikabu seamount is a constituent of the Kashiwagi Unit. The peak metamorphic ages of the Manba and Kamiyoshida Units were obtained as 132–107 Ma and 163–144 Ma, respectively. Major structural discontinuity is suggested within the Middle Jurassic accretionary complexes.

Hydrological connectivity plays a major role in solving water resource and eco-environmental problems. However, this phenomenon has not been afforded the attention it deserves. Detailed analysis of connectivity in river systems could provide considerable insight into structural and functional attributes of riverine landscapes. The current study used graph theory approach and associated connectivity indicators to explore the characteristics and evolution of river systems and hydrological connectivity in a large catchment (Poyang Lake, China). The results revealed that the structure of the river system tended to be complex during 1990-2020, characterized by a dynamic evolution of tributaries in certain northern areas. Both river density and complexity exhibited an increasing trend by up to 15%, with the change rate after 2000 approximately twice as high as that of the preceding period. Overall, human activities across the catchment are more likely to play a key role in leading to significant changes in the quantity, morphometric, and structure characteristics of the river system. Additionally, the functional connectivity analysis indicated that the index of connectivity (IC) in the downstream catchment is stronger than that of the upstream vegetation areas, suggesting a strong contribution to the runoff-sediment transport (r=0.6-0.7). This study highlights the spatial and temporal evolution of both the structural and functional connectivity in the large Poyang Lake catchment. The findings of this work will bene-fit future water resource management and applications by providing a strategy for protecting the surface hydrology and mass transport of large river basins under climate and land-use changes.

When the epipelic algae group growing on the concrete inclined side wall, which is typical of urban rivers and open diversion channels, enters the water flow, it will seriously affect the func-tion of the rivers or the channels. It is urgent to predict the transport capacity of epipelic algae group with water flow. However, the current research on the transport of pollutants is mostly based on mathematical models, and the study of the transport of flake epipelic algae group is extremely rare. A generalized hydrodynamic experimental model of a flume with sidewall epi-pelic algae group was established. Through a series of hydraulic experiments, the physical movement form and transport capacity of the suspended epipelic algae group on the side wall of the channel were studied qualitatively and quantitatively by taking the thickness, sheet size and flow rate of the epipelic algae group as the influencing factors. The key influencing factors of the suspension of epipelic algae are clarified, so as to quantitatively analyze the critical conditions of its suspension. Through flow scheduling, the probability of epipelic algae gathering some-where is increased. It provides a theoretical basis for realizing the long-distance migration of epipelic algae and optimizing the mathematical model.

With the development of deep learning, several Graph Neural Networks (GNN)-based approaches have been utilized for text classification. However, GNNs encounter challenges in capturing contextual text information within a document sequence. To address this, a novel text classification model RB-GAT is proposed by combining RoBERTa-BiGRU embedding and a multi-head Graph ATtention Network (GAT). First, the pre-trained RoBERTa model is exploited to learn word and text embeddings in different contexts. Second, the Bidirectional Gated Recurrent Unit (BiGRU) is employed to capture long-term dependencies and bidirectional sentence information from the text context. Next, the multi-head graph attention network is applied to analyze this information, which serves as a node feature for the document. Finally, the classification results are generated through a Softmax layer. Experimental results on three benchmark datasets demonstrate that our method can achieve an accuracy of 71.48%, 98.45%, and 80.32% on Ohsumed, R8, and MR, which is superior to the existing nine text classification approaches.

In offshore drilling, accidents such as gas invasion, overflow, and kicks are inevitable, and they can escalate into blowouts and other catastrophic events that result in casualties and substantial economic losses. Therefore, maintaining drilling safety requires accurate monitoring of gas invasion and overflow. The majority of overflow monitoring methods currently utilized at drilling sites are threshold-based. However, monitoring parameters acquired during actual drilling operations frequently contain noise signals, making it difficult for threshold-based methods to strike a balance between improving accuracy and minimizing false positives. In this paper, Pattern Recognition-based Kick Detection (PRKD) is proposed as a novel method for diagnosing overflow in offshore drilling. This method utilizes the overflow evolution process by integrating multi-phase flow calculations, data filtering theory, pattern recognition theory, the Bayesian framework, and other theoretical models. The PRKD effectively detects and monitors gas intrusion and overflow based on single parameters by analyzing the shape and wave characteristics of the curves. The case analysis demonstrates that the proposed method for monitoring drilling overflow achieves high precision while maintaining a low false positive rate. By combining advanced computational techniques with pattern recognition algorithms, the PRKD improves the accuracy and reliability of kick detection, enabling proactive responses to potential risks, protecting the environment and human lives, and optimizing drilling operations.

Many engineered approaches have been proposed over the years for solving the hard problem of performing indoor localisation using smartphone sensors. However, specialising these solutions for difficult edge cases remains challenging. Here we propose an end-to-end hybrid multimodal deep neural network localisation system, MM-Loc, relying on zero hand-engineered features, learning them automatically from data instead. This is achieved by using modality-specific neural networks to extract preliminary features from each sensing modality, which are then combined by cross-modality neural structures. We show that our choice of modality-specific neural architectures is capable of estimating the location with good accuracy independently. But for better accuracy, a multimodal neural network fusing the features of early modality-specific representations is a better proposition. Our proposed MM-Loc solution is tested on cross-modality samples characterised by different sampling rates and data representation (inertial sensors, magnetic and WiFi signals), outperforming traditional approaches for location estimation. MM-Loc elegantly trains directly from data unlike conventional indoor positioning systems, which rely on human intuition.

NongXiangXing Baijiu (NBJ) is produced using a solid-state fermentation system, but the impact of stratified fermented grains on fermentation remains unclear. Therefore, in a typical distillery plant, we evaluated the physical and chemical composition, volatile compound profile, and microbial community of fermented grains in NBJ both above (FG-A) and below (FG-B) the Huangshui line. Significant differences in fermentation parameters between FG-A and FG-B were observed after 30 days of fermentation (P < 0.05). Additionally, the partial least squares projection to latent structure discriminant analysis (PLS-DA) revealed distinct differences in volatile compounds between FG-B and FG-A, identifying 26 discriminant markers. The diversity of short-chain fatty acids (SCFAs) and their esters was higher in FG-B compared to FG-A. Furthermore, microbial diversity and abundance differed significantly between the two layers of fermented grains (P < 0.05). Correlation and pathway enrichment analyses indicated that the higher SCFA content in FG-B could be attributed to the greater abundance of acid-producing microorganisms compared to FG-A. This study highlights the differences between the two layers of fermented grains in NBJ fermentation, offering new insights into solid-state fermentation and expanding the current understanding of the traditional NBJ fermentation process.

(1) Background: Most of the existing studies focus on the evaluation of technology finance; the relationship between technology finance and technology innovation. But there are few studies on the development of technology finance and the quality of economic development in our country; (2) Methods: Based on the panel data of 30 provinces in China, this paper constructs an index system to measure the development of technology finance through the improved entropy method, and tests the spatial correlation of the development of technology finance in China by Moran'I index. According to the test results, this paper constructs a spatial econometric model to empirically analyze the promoting effect of scientific, technological and financial development on high-quality economic development, and analyzes its promoting effect in different regions and different time periods; (3) Results: The results show that the quality of China's economic growth is spatially dependent, and the development of science, technology and finance can significantly promote the quality economic development in China. And the promotion coefficient of the central region is the largest, as well as the coefficient of the eastern region is the smallest. The promotion coefficient was small and not significant before 2015, and was significantly positive after 2015; (4) Conclusions: this paper puts forward the corresponding policy recommendations according to the research results.

Our understanding of phylogenetic relationships among Gadiformes fish is obtained through the analysis of a small number of genes, but uncertainty remains around critical nodes. A series of phylogenetic controversial exists at the suborder, family, subfamily, and species levels. A total of 1105 orthologous exon sequences and translated amino acid sequences from 36 genomes and 12 transcriptomes covering 33 species were applied to investigate the phylogenetic relationships within Gadiformes and address these problems. Phylogenetic trees reconstructed with the amino acid data set using different tree-building methods (RAxML and MrBayes) showed consistent topology. The monophyly of Gadifromes was confirmed in our study. However, the three suborders Muraenolepidoidei, Macrouroidei, and Gadoidei were not well recovered by our phy-logenomic study, rejecting the validity of suborder Muraenolepidoidei. Four major lineages were revealed in this study. The family Bregmacerotidae forming clade I was the basal lineage of Gadiformes. The family Merluciidae formed clade II. Clade III contained families Melanonidae, Muraenolepididae, Macrouridae (with subfamilies Trachyrincinae, Macrourinae, and Bathygadinae), and Moridae. Clade IV contained at least three families of suborder Gadoidei, i.e., Gadidae, Phycidae, and Ranicipitidae. The subspecies of Lota lota from Amur River were confirmed, indicating that exon markers were a valid high-resolution method for delimiting subspecies or distinct lineages within species level. The PSMC analysis of different populations of L. lota suggests a continuous decline since 2 Myr.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The earth pressure acting on soilbag reinforced retaining structures subjected to surcharge loads under non-limited states, is crucial for designing these structures. In this study, the earth pressures are investigated through model tests of the soilbag reinforced retaining wall. Findings from these tests reveal a non-linear distribution of lateral earth pressure on the wall when subjected to surcharge loads in non-limited states, with an observed escalation in pressure corresponding to increased surcharge loads. Compression tests on soilbags were conducted to analyze their lateral stress-strain behavior. Insights from these tests facilitated the development of a predictive method for estimating lateral pressure on soilbag reinforced retaining walls under similar conditions. This method, rooted in the principle of force equilibrium in differential elements, has its accuracy and reliability substantiated by the alignment of its predictions with the model test outcomes.

Ocean big data is the scientific practice of using big data technology in the marine field. Data from satellites, manned spacecraft, space stations, airship, unmanned aerial vehicles, shore-based radar and observation stations, exploration platforms, buoys, underwater gliders, submersibles, and submarine observation networks are seamlessly combined into the ocean’s big data. Increasing numbers of scholars have tried to fully analyze the ocean’s big data. To explore the key research technology knowledge graphs related to ocean big data, articles between 1990 and 2020 were collected from the “Web of Science”. By comparing bibliometric software and using the visualization software Cite-Space, the pivotal literature related to ocean big data, as well as countries, institutions, categories, and keywords, were visualized and recognized. Journal co-citation analysis networks can help determine the national distribution of core journals. Co-citation analysis networks for documents show authors who are influential at key technical levels. Key co-occurrence analysis network keywords can determine research hot spots and research frontiers. The three supporting elements of marine big data research are shown in the co-citation network. These elements are author, institution, and country. By examining the co-occurrence of keywords, the key technology research directions for future marine big data were determined.

Initial attempts to develop monoclonal antibodies as therapeutics to resolve influenza infections focused mainly on searching for antibodies with the potential to neutralise the virus in vitro with classical haemagglutination inhibition and micro-neutralisation assays. This led to the identification of many antibodies that bind to the head domain of haemagglutinin (HA) which generally have potent neutralisation capabilities that block viral entry or viral membrane fusion. However, this class of antibodies has a narrow breadth of protection in that they are usually strain specific. This led to the emphasis on stalk targeting antibodies which are able to bind a broad range of viral targets that span across different influenza subtypes. Recently, a third class of antibodies targeting the vestigial esterase (VE) domain have been characterised. In this review, we describe the key features of neutralising VE targeting antibodies and compare them with head and stalk class antibodies.

Recent advancements in Artificial Intelligence (AI) and generative models have significantly accelerated the evolution of internet services. In data centers, where data is often distributed across multiple machines, leveraging these machines to expedite the training of machine learning applications is common. However, this approach incurs substantial communication overhead. To mitigate this, data compression techniques such as quantization, sparsification, and dimension reduction are gaining attention, especially with iterative training algorithms that frequently exchange gradients. With the advancement of FPGA technology, FPGA-based bump-in-the-wire network interface controllers (smartNICs) have demonstrated notable benefits for data centers, matching ASIC switches in port-to-port latency and capacity. However, FPGA-based switches often have spare hardware resources beyond their switching functions, which are typically wasted. we propose a novel architecture that integrates FPGA-based switches with ensemble learning methods, utilizing these spare resources on FPGA-based network switches. This architecture employs random projection as a compression method to accelerate machine learning tasks while maintaining high accuracy. Our system accelerates the training process for Multilayer Perceptron (MLP) models with a speedup of 2.1-6.7 times across four high-dimensional datasets. In addition, it leverages the Hamming distance metric for k-Nearest Neighbors (kNN) classification, combining random projection with Hamming encoding, to offload large-scale classification tasks from downstream servers. This achieves a worst-case speedup of 2.3-8.7 times and a memory reduction of 3.9-27.7 times compared to CPU-based kNN classifiers using cosine distance. Our architecture addresses the challenges of high-dimensional data processing and exemplifies the potential of AI-driven solutions in accelerating and optimizing internet services. Moreover, the programmability of FPGAs allows the system to adopt various compression methods, extending its applicability. Offloading tasks to FPGAs can significantly reduce query response times, showcasing a crucial step towards achieving greater levels of autonomic computing and the rapid evolution of internet systems.

Semi-continuous data are very common in the social science and economics. In this paper, a Bayesian variable selection procedure is developed to assess the influence of exogenous factors including observed and unobserved on the semi-continuous data. Our formulation is based on the two-part latent variable model with polytomous response. We consider two schemes for the penalties of regression coefficients and factor loadings: the Bayesian spike and slab bimodal prior and the Bayesian lasso prior. Within the Bayesian framework, we implement Markov Chains Monte Carlo sampling method to conduct posterior inference. To facilitate posterior sampling, we recast the logistic model in part one as the norm-like mixture model. Gibbs sampler is designed to draw observations from the posterior. Our empirical results show that with suitable hyper-parameters, the spike and slab bimodal method slightly outperforms the Bayesian lasso in the current analysis. Finally, a real example related to the China household finance survey is analyzed to illustrate the application of the methodology.. .

The number of visible navigation satellites in a multi-constellation system increases exponentially compared to a single constellation, significantly increasing the complexity of the system state equations in the data fusion algorithm of a tightly coupled navigation system. This results in an exponential increase in the computation volume for navigation and positioning, seriously affecting real-time performance. To address this, a low-cost, low-computation satellite screening algorithm is proposed. It adaptively changes the number of constellation satellites by setting different screening thresholds and adjusting the number of remaining satellites. The algorithm then sorts and differentiates the azimuth and elevation angles of the screened satellites to form a selection strategy that divides the space region multiple times, enabling fast satellite selection. This approach greatly reduces the calculation amount while ensuring positioning accuracy. Experimental results show that the proposed algorithm maintains positioning differences within 5 meters compared to traditional satellite selection algorithms, and the time consumed for selecting a single epoch is greatly reduced. This indicates that the algorithm is suitable for low-cost multi-constellation satellite positioning systems.

The service life of the reinforced concrete structure in the marine environment can be impaired significantly due to chloride-induced corrosion. However, how the chloride diffusion in pre-cracked concrete structures is affected by the hydrostatic pressure magnitude is poorly understood. This study experimentally examined the effect of hydrostatic pressure on the chloride diffusion in pre-cracked concrete. Cracks with five different widths, i.e., 20 μm, 40 μm, 60 μm, 80 μm, and 100 μm, were manually created using a splitting tensile apparatus respectively. The chloride diffusion in the concrete with a certain crack was then studied under four different hydrostatic pressures of 0 MPa, 0.1 MPa, 0.3 MPa, and 0.5 MPa. Experimental results show that the chloride diffusion in concrete with a crack greatly relies on both the hydrostatic pressure and the crack width. The chloride concentration increases as the hydrostatic pressure grows, particularly for the wider cracks with width ranging from 60 μm to 100 μm. Surprisingly, the hydrostatic pressure has a negligible effect on the chloride distribution in the concrete with a crack width no larger than 40 μm. Both the chloride diffusion coefficient and the surface chloride concentration of concrete increased gradually as the hydrostatic pressure increased. The experimental findings enrich our understanding of the behavior of pre-cracked concrete when exposed to chloride-induced corrosion at different depths of marine environments.

Environmental nanoparticles have been shown to exist in most aquatic environments, and environmental nanoparticles in water distribution systems significantly affect water quality. However, little research has been conducted on the environmental nanoparticles in mineral water, which is a special water resource. Nanoparticle tracking analysis (NTA) and high-resolution transmission electron microscopy (HRTEM) were conducted. This study was the first to identify many environmental nanoparticles in natural mineral water in Zibo City, Shandong Province, China. The results of the NTA showed that the concentration of the particles was 5.5 ×106 particles/mL and the peak diameter of the size distribution was 180 nm. The HRTEM showed that the nanoparticles were granular, pinniform, rodlike, and flakey in shape, and some of the nanoparticles existed in aggregation. The energy-dispersive spectrometry results showed that most of the nanoparticles contained O, Mg, Ca, Si, Fe, Ti, and P, and some of them also contained F, V, S, and Mn. When combined with the characteristics of the selected area electron diffraction pattern, the nanoparticles were confirmed to be Ca-bearing nanoparticles, attapulgite nanorods, MnO2 nanosheets, and TiO2 nanoparticles. These results indicate a new form of elements occurring in mineral water. In addition, based on the chemical and physical characteristics of the nanoparticles and mineral water, these environmental nanoparticles in the mineral water are likely to be the weathering byproducts of minerals. These nanoparticles within mineral water provide a good opportunity for understanding the behavior of nanoparticles in varied systems. Moreover, environmental nanoparticle science is important for continuing efforts in water safety, treatment, and remediation.

To investigate the composition of caproic acid-producing bacterial communities in sub-high-temperature Daqu, we analyzed four different Daqu samples from Sichuan. After enriching the samples with a specialized medium, we performed high-throughput sequencing of 16S rRNA gene amplicons on the metagenomic DNA from both the Daqu samples and the enrichment cultures. Our analysis focused on identifying and characterizing the caproic acid-producing bacterial communities present in Daqu. The results revealed that enrichment increased both the diversity and abundance of potential caproic acid-producing bacteria in Daqu. The predominant caproic acid-producing bacteria, with a relative abundance greater than 1%, included Clostridium sensu stricto 18 (2.19% to 69.00%), Clostridium sensu stricto 15 (1.76% to 7.65%), as well as smaller amounts of Clostridium sensu stricto 12, Clostridium sensu stricto 1, Clostridium sensu stricto 10, Clostridium sensu stricto 7, and Caproiciproducens. Specifically, Q1 Daqu was characterized by the presence of Clostridium sensu stricto 18 and Clostridium sensu stricto 15. Q2 Daqu featured Clostridium sensu stricto 1, Caproiciproducens, and Clostridium sensu stricto 18. Q3 Daqu included Clostridium sensu stricto 18 and Caproiciproducens. Q4 Daqu contained Clostridium sensu stricto 18 and Clostridium sensu stricto 1. These findings indicate that there are variations in the composition of caproic acid-producing bacterial communities among different sub-high-temperature Daqu samples from Sichuan. This preliminary analysis provides a theoretical basis for further studies on caproic acid bacteria in Daqu and offers insights into the development of high-quality Daqu, which may enhance the quality of Nongxiangxing liquor.

Public-Private Partnerships (P3 or PPPs) have been utilized and studied more frequently over the past couple of decades for both infrastructure projects and building development projects. Based upon the records of the outcomes of these projects there is a plethora of data that demonstrates the benefits and challenges that this delivery method poses. As the name suggests, these partnerships allow for public goals to become realized while also providing opportunities for the private sector to gain business success. These two often divergent interests are finding mutual benefit but the process of compromises also comes with some disadvantages that should be understood in order to make decision of whether the risk/reward equation works for all stakeholders. In particular, this paper will focus on how PPPs affect the construction aspects of projects and will assert how to understand the risks and evaluate the benefits from a construction perspective.

Based on the theory of behavioral economics, this study deeply analyzes the principles of behavioral economics involved in the development of mass sports, including psychological expectation, selection deviation and incentive mechanism, rationalize the current situation of group sports development, discusses how to effectively promote the development of mass sports, and puts forward a series of concrete countermeasures. In view of the problem of behavioral expectations, it is suggested to establish a comprehensive publicity and education system to improve the public's awareness and understanding of sports, and to stimulate individuals' active participation through self-setting goals and planning methods. In view of the selection bias, it is suggested that the government and relevant institutions provide diversified and attractive sports activity options, and make full use of technological means to increase the visibility and participation of activities.In addition, in view of the incentive mechanism problem, it is advocated to adopt differentiated incentive measures to meet the needs of different groups. The government can provide some preferential policies and establish incentive mechanisms to provide support for the organization of mass sports activities. It is expected that this research can stimulate the enthusiasm of the masses to participate in sports and promote the healthy development of mass sports.

Most natural language processing (NLP) tasks operate an input sentence as a sequence with token-level embeddings and features, despite its clausal structures. Taking Abstract Meaning Representation (AMR) parsing as an example, recent parsers are empowered by Transformers and pre-trained language models, but long-distance dependencies (LDDs) introduced by long sequences are still open problems. We argue that LDDs are not superficially blamed on the sequence length but are essentially related to the internal clause hierarchy. Typically, non-verb words in a clause cannot depend on words outside, and verbs from different but related clauses have much longer dependencies than those in the same clause. With this intuition, we introduce a type of clausal feature, hierarchical clause annotation (HCA), into AMR parsing and propose two HCA-based approaches, HCA-based self-attention (HCA-SA) and HCA-based curriculum learning (HCA-CL), to integrate HCA trees of complex sentences for addressing LDDs. We conduct extensive experiments on two in-distribution (ID) AMR datasets (AMR 2.0 and AMR 3.0) and three out-of-distribution (OOD) ones (TLP, New3, and Bio). Experimental results show that our HCA-based approaches achieve significant and explainable improvements against the baseline model and outperform the state-of-the-art (SOTA) model when encountering sentences with complex clausal structures that introduce most LDD cases.

Curcumin is a promising anti-cancer drug but its applications in cancer therapy are limited due to its poor solubility, short half-life and low bioavailability. In this study, curcumin loaded magnetic alginate / chitosan nanoparticles were fabricated to improve the bioavailability, uptake efficiency and cytotoxicity of curcumin to MDA-MB-231 breast cancer cells. Alginate and chitosan were deposited on Fe3O4 magnetic nanoparticles based on their electrostatic properties. The sizes of the nanoparticles (120-200 nm) were within the optimum range for drug delivery. Sustained curcumin release was obtained use the nanoparticles with the ability to control the curcumin release rate by altering the number of chitosan and alginate layers. Confocal fluorescence microscopy results showed that targeted delivery of curcumin with the aid of magnetic field were achieved. The FACS assay indicated that MDA-MB-231 cells treated with curcumin loaded nanoparticles had a 3-6 folds uptake efficiency to those treated with free curcumin. MTT assay indicated that the curcumin loaded nanoparticles exhibited significantly higher cytotoxicity toward MDA-MB-231 cells than toward HDF cells. The sustained release profiles, enhanced uptake efficiency and cytotoxicity to cancer cells as well as the targeting potential make MACPs a promising candidate for cancer therapy.

We recently found that in human osteoblasts Homer1 complexes to CaSR and mediates AKT initiation via mTORC2 leading to beneficial effects in osteoblasts including -catenin stabilization and mTORC1 activation (doi: 10.1074/jbc.RA118.006587). Herein we further investigated the relationship between Homer1 and CaSR and demonstrate a link between the protein levels of CaSR and Homer1 in human osteoblasts in primary culture. Thus, when siRNA was used to suppress the CaSR, we observed upregulated Homer1 levels and when siRNA was used to suppress Homer1 we observed downregulated CaSR protein levels using immunofluorescence staining of cultured osteoblasts as well as western blot analyses of cell protein extracts. This finding was confirmed in vivo as the bone cells from osteoblast specific CaSR(-/-) mice showed increased Homer1 expression compared to wild-type. Furthermore, when the commonly used osteosarcoma cell lines MG63 and SAOS-2 were compared to primary osteoblasts, higher levels of Homer1 protein were associated with increased protein levels of the CaSR as well as mTOR and Rictor. CaSR and Homer1 protein were both expressed in osteocytes embedded in the long bones of wild-type mice, and immunofluorescent studies of these cells revealed that Homer1 protein sub-cellular localization was markedly altered in the osteocytes of CaSR(-/-) mice compared to wt. The study identifies additional roles for Homer1 in the control of the protein level and subcellular localization of CaSR in cells of the osteoblast lineage, in addition to its established role of mTORC2 activation downstream of the receptor.

The basic idea is to expand the completed zeta function $\xi(s)$ in MacLaurin series (infinite polynomial), which can be further expressed as infinite product (Hadamard product) by conjugate complex roots. Finally, the functional equation $\xi(s)=\xi(1-s)$ leads to $(s-\alpha_i)^2 = (1-s-\alpha_i)^2, i \in \mathbb{N}$ with solution $\alpha_i= \frac{1}{2}, i \in \mathbb{N}$, where $\alpha_i$ are the real parts of the zeros of $\xi(s)$, i.e., $s_i =\alpha_i\pm j\beta_i, i\in \mathbb{N}$. Therefore, a proof of the Riemann Hypothesis is achieved.

This paper shares our work in developing and implementing an immersive gamification training platform for students who undergo manufacturing shopfloor training at the School of Engineering, Nanyang Polytechnic, Singapore. In this gamification training platform, we developed a virtual manufacturing shopfloor that is identical to the actual shopfloor located in the school. Students have the freedom to learn the manufacturing shopfloor operations and safety acts through the various game scenarios and training tasks which include workshop safety, CNC machine introduction, CNC machining dynamics, MES, etc. In addition, the assessment feature with immediate feedback were embedded within the gamification platform, which aim to help students to assess their level of understanding and help teachers to monitor the learning progress of their students. To investigate the impact of this gamification training platform on students’ learning outcome and motivation in manufacturing shopfloor technologies and safety acts, a pilot study was conducted in AY2018 semester 2 for a total 134 students from 4 classes of digital & precision engineering diploma. It is found that gamification can be integrated effectively into manufacturing education to motivate students and enhance their learning effectiveness. Based on the collected data from the technical quizzes and satisfactory survey, the results showed that the integration of gamification into the classroom learning not only added a stimulating and captivating game-like layer to the learning experience of the students, but also provided a safe environment for students to learn without fear of making errors. Challenges faced in implementing this gamification training platform will also be discussed in this paper.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

Arctic sea ice prediction holds significant importance for facilitating Arctic route planning, optimizing fisheries management, and advancing the field of sea ice dynamics research. While various deep learning models have been developed for sea ice prediction, they predominantly operate at the seasonal or sub-seasonal scale, often focusing on localized areas, and few cater to full-region daily scale prediction. This study introduces the use of spatiotemporal sequence data prediction models, namely, the convolutional LSTM (ConvLSTM) and predictive recurrent neural network (PredRNN), for the prediction of sea ice concentration (SIC). Our analysis reveals that, when solely utilizing SIC historical data as the input, the ConvLSTM model outperforms the PredRNN model in SIC prediction. To enhance the model's capacity to capture spatiotemporal relationships between multiple variables, we expanded the range of input data types to form the ConvLSTM-multi and PredRNN-multi models. Experimental findings demonstrate that the ConvLSTM-multi model excels in assimilating the influence of reanalysis data on sea ice within the sea ice edge region, thus exhibiting superior performance in predicting daily Arctic SIC over the subsequent 10 days. Furthermore, sensitivity tests on various model parameters highlight the substantial impact of sea surface temperature and prediction date on the accuracy of daily sea ice prediction. Additionally, meteorological and oceanographic parameters primarily affect the prediction accuracy of the thin ice region at the edge of the sea ice.

Most natural language processing (NLP) tasks suffer performance degradation when encountering long complex sentences, such as semantic parsing, syntactic parsing, machine translation, and text summarization. Previous works address the issue with an intuition of decomposing complex sentences and linking simple ones, such as RST-style discourse parsing, split-and-rephrase (SPRP), text simplification (TS), simple-sentence-decomposition (SSD), etc. However, these works are not applicable for semantic parsing like abstract meaning representation (AMR) parsing and semantic dependency parsing due to misalignments to semantic relations and unavailabilities to preserve original semantics. Following the same intuition and avoiding deficiencies of previous works, we propose a novel framework, hierarchical clause annotation (HCA), based on the linguistic research of clause hierarchy. With the HCA framework, we annotate a large HCA corpus to explore the potentialities of integrating HCA structural features into semantic parsing with complex sentences. Moreover, we decompose HCA into two subtasks, i.e., clause segmentation and clause parsing, and provide neural baseline models for more silver annotations.

Ocean exploration is crucial for utilizing its extensive resources. Images captured by underwater robots suffer from issues such as color distortion and reduced contrast. To address the issue, we propose an innovative enhancement algorithm that integrates Transformer and Convolutional Neural Network (CNN) in a parallel fusion manner. Firstly, a novel transformer model is intro-duced to capture local features, employing peak-signal-to-noise ratio (PSNR) attention and linear operations. Subsequently, to extract global features, both temporal and frequency domain features are incorporated to construct convolutional neural network. Finally, the Fourier’s high and low-frequency information of the original image are utilized to fuse different features. To demon-strate the algorithm's effectiveness, underwater images with various levels of color distortion are selected for both qualitative and quantitative analyses. The experimental results demonstrate that our approach surpasses other mainstream methods, achieving superior PSNR and structural sim-ilarity index measure (SSIM) metrics and leading to a detection performance improvement of over ten percent.

Proteomics is the study of cellular proteome by investigating how different proteins interact with each other and the roles they play in the organism. For mRNA expression levels do not always correlate well with protein expression levels, and the study of mRNA does not consider protein posttranslational modifications (PTMs), complex formation and localization; all of which are key to protein function. Quantitative proteomics uses mass spectrometry to identify and quantify proteins so as to find differentially expressed proteins under different condition. This allows us to gain biological insights under stress or other pathological conditions. posttranslational modifications, such as lysine acetylation, succinylation and lactylation, occur after protein biosynthesis and play vital roles in protein activity and cell physiology regulation. Here we present the mass spectrometry analysis in detail to unveil protein acylase and deacylase’ roles in metabolic regulation based on PTMomics lysine acetylome and suincylome.

Immunohistochemistry (IHC) helps identify different types of tissues and provides important information about the pattern, shape, and structure of cells in a tissue sample. It is a very useful tool and widely used to uncover histology and pathology diagnosis uses. The IHC is a very useful tool to conduct research in the developmental biology area. Some insects, like butterflies, bees, beetles, ants, wasps, and moths, undergo a unique life cycle called complete metamorphosis, which has four distinct stages: egg, larva, pupa, and adult. Larvae are often wingless and have different habits and forms than adults, which are better suited for growth and development. During the metamorphosis, how does the insect legs change is a really an interesting issue.To better understand insect development, agriculture pest control, and insect pathogen interaction, here we use an insect Bombyx mori (domestic silk moth) as a model to detail how to conduct the IHC assays, such as HE staining, TUNEL to see the cell apoptosis, pH3 and BrdU staining to check cell division. The reagents can be easily found, and this step-by-step protocol is easily reproduced.

Road cracks significantly affect the serviceability and safety of roadways, especially in mountainous terrain. Traditional inspection methods, such as manual detection, are excessively time-consuming, labor-intensive, and inefficient. Additionally, multi-function detection vehicles equipped with various sensors are expensive and not suitable for mountainous roads due to poor conditions. To address these challenges, this study proposes a customized Unmanned Aerial Vehicles (UAV) inspection system designed for automatic crack detection. The system focuses on enhancing autonomous capabilities in mountainous terrains by incorporating embedded algorithms for route planning, autonomous navigation, and automatic crack detection. The slide window method is proposed to enhance the autonomous navigation of UAV flights by generating path planning in mountainous roads. This method compensates for GPS/IMU positioning errors, particularly in GPS-denied or GPS-drift scenarios. Moreover, the YOLOv8 algorithm is introduced to conduct autonomous crack detection from UAV imagery in the offboard module. To validate our UAV inspection system's performance, we conducted several experiments to assess its accuracy, robustness, and efficiency. The experimental results demonstrate that our UAS inspection system accurately estimates the flight trajectory along the mountainous road for autonomous navigation. Furthermore, the experimental detection results also demonstrate that the YOLOv8 algorithm achieves higher recognition accuracy compared to the YOLOv5, and YOLOv7-tiny algorithms, exceeding 3.1%,and 6.8% of mAP, respectively. In summary, the UAV inspection system proposed in this study can provide a useful tool and technological guidance for the regular inspection of mountainous roads.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Ecological city is currently a hot topic in urban planning research. How to balance urban development and ecological environment protection has become a focus and difficulty of research. Traditional urban planning is mainly based on experience, but its disadvantage is that it is easy to overlook key geographical factors such as terrain and vegetation, and cannot fully reflect the actual spatial characteristics of the city. Therefore, this article applied the combination of urban and rural planning and environmental remote sensing technology to urban planning and design, obtaining a massive amount of data. Through the actual analysis of Langfang, this paper monitored the vegetation, water, land and landscape data of Langfang through environmental remote sensing technology. By using these data to identify existing problems, this article proposed reasonable planning for the problems, in order to achieve the effective goal of ecological city planning and design. It provided a more accurate analysis of urban structure, including urban planning and urban ecological landscape planning. Among them, ecological landscape planning includes renovating ecological embankments, protecting ecological green belts around the city, and creating characteristic landscape areas, thereby providing more scientific basis for urban planning and design, making urban planning and design more reasonable and scientific. This paper investigated the planned Langfang City, and the average errors of vegetation, soil, water quality, and landscape data obtained from traditional field surveys were 0.35, 0.33, 0.34, and 0.31, respectively. The average errors of remote sensing technology in obtaining vegetation, soil, water quality, and landscape data were 0.16, 0.15, 0.17, and 0.15, respectively. The total suspended solids content of waterscape 1-10 before planning was 5.51mg/L and 7.41mg/L, respectively. After planning, the total suspended solids content of waterscape 1-10 was 3.60mg/L and 4.47mg/L, respectively. From this, it can be seen that the error in obtaining data after planning has decreased, and the total suspended solids content has also decreased.

Amidst the escalating demands for efficient Intelligent Transportation Systems (ITS) management, the significance of accurate Origin-Destination (OD) data prediction has emerged as a paramount concern, given its indispensable role in the ITS domain. This paper introduces a groundbreaking integrated model, creatively fusing the unique strengths of Graph Convolutional Network (GCN), Residual Neural Network (ResNet), and Long Short-Term Memory Network (LSTM) into a single architecture, which we name GraphResLSTM, to exploit road segment average speed data for OD prediction. Compared with conventional road segment traffic volume data, average speed data is more readily available, significantly reducing the data accessibility barrier for OD prediction. We underscore the critical role of selection of key road segments and employs a combination of Entropy Weight Method and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) to identify 41 representative road segments from the experimental road network. In the experimental phase, we simulate 86400000 seconds of traffic conditions, generating a total of 1440000 data records. Utilizing these simulated data, we design and conduct comparative experiments between models as well as data types. The results demonstrate that both the GraphResLSTM model and road segment average speed data outperform other models and data types notably in OD prediction tasks.

This paper presents a compact wideband circularly polarized cross dipole antenna with low-pass filter response. It consists of two pairs of folded crossed dipole arms printed separately on both sides of the top substrate, and the two dipole arms on the same surface are connected by an annular phase-shifting delay line to generate circular polarization. A bent metal square ring and four small metal square rings around the cross dipoles are employed to introduce new resonant frequencies, effectively extending the impedance and axial ratio bandwidth. Four square patches printed on the middle substrate are connected to the ground plane by the vertical metal plates, in order to reduce the antenna height. Thus, a compact wideband circularly polarized antenna is realized. In addition, a transmission zero can be introduced at the upper frequency stopband by the bent metal square rings, without using extra filter circuits. For verification, the proposed model is implemented and tested. The overall size of the model is 90mm×90mm×33mm(0.37λ0×0.37λ0×0.14λ0, λ0 denotes the center operating frequency). The measured impedance bandwidth and 3 dB axial ratio bandwidth are 53.3% and 41%, respectively. More than 15 dB upper-band radiation suppression level is realized, indicating a good low-pass filter response.

This paper aims to address the exponential stability and stabilization problems for a class of delayed nonlinear Markov jump systems under randomly occurring Denial-of-Service (DoS) attack and packet loss. Firstly, the stochastic characteristics of DoS attack and packet loss are depicted by the attack success rate and packet loss rate. Secondly, a Period Observation Window (POW) method and a hybrid-input strategy are proposed to compensate for the impact of DoS attack and packet loss on the system. Thirdly, A Dynamic Event-triggered Mechanism (DETM) is introduced to save more network resources and ensure the security and reliability of systems. Then, by constructing a general common Lyapunov functional and combining with the DETM and other inequality analysis techniques, the less conservative stability and stabilization criteria for the underlying systems are derived. In the end, the effectiveness of our result is verified through a numerical example.

In (Semigroup Forum 77: 325-338, 2008) Mahmoudi M. and Renshaw J. solved a study that covers of cyclic $S$-acts over monoids. This article is an attempt to initiate the covers of finitely generated $S$-acts. We give a necessary and sufficient condition for a monoid to have the properties that $n$-generated $S$-acts have strongly flat covers, Condition $(P)$ covers and projective covers. The main conclusions extend some known results. We show also that Condition $(P)$ covers of finitely generated $S$-acts are not unique, unlike the situation for strongly flat covers. Additionally, we demonstrate that the property of Enochs' $\mathcal{X}$-precover of $S$-act $A$, where $\mathcal{X}$ denotes a class of $S$-acts that are closed under isomorphisms.

To enhance the safety of power grid operations, this study proposes a high-precision short-term photovoltaic power prediction method that integrates information from surrounding pho-tovoltaic stations and the Conv-LSTM-ATT model. In the deep learning prediction model, not only is numerical weather prediction (NWP) data from the target photovoltaic station used as input features, but also highly correlated features from nearby photovoltaic stations are incor-porated. The research begins by analyzing the correlation between irradiance and power se-quences, along with distance factors, to calculate a composite similarity index between the target and other regional photovoltaic stations. Stations with high similarity indices are then selected as data sources. Subsequently, Bayesian optimization techniques are employed to find the optimal data fusion ratios. Ultimately, using the selected data, power prediction mod-eling is conducted via the Conv-LSTM-ATT deep neural network. Experimental results con-firm the superiority of the proposed model, which demonstrates higher predictive accuracy compared to three other classical models. The data fusion strategy determined by Bayesian optimization significantly enhances prediction accuracy, reducing the root mean square error (RMSE) of the test set by 20.04%, 28.24%, and 30.94% for three weather types, respectively.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Type 2 diabetes mellitus (T2DM), a multifactorial and complicated metabolic disorder, is a growing public health problems. Numerous studies indicated that bioactive compounds from herbal medicine have beneficial effects on T2DM prevention and treatment, owing to their numerous biological properties. Curcumin, the major curcuminoid of turmeric, is one of the most studied bioactive components of herbal supplements, which has a variety of biological activities. Clinical trials and preclinical research have recently produced compelling data to demonstrate the crucial functions of curcumin against T2DM via several routes. Accordingly, this review systematically summarizes the antidiabetic activity of curcumin, along with various mechanisms. Results showed that effectiveness of curcumin on T2DM is due to it being anti-inflammatory, anti-oxidant, anti-hyperglycemic, anti-apoptotic, anti-hyperlipidemia and other activities. In light of these results, curcumin may be a promising prevention/treatment choice for T2DM.

The carbonation of industrial calcium-rich byproducts such as steel slag demonstrates significant potential for CO2 sequestration. This technique aids in reducing carbon emissions while also promoting waste recycling. Despite its advantages, gaps remain in understanding how steel slag characteristics and operational parameters influence the carbonation process, as well as the underlying mechanism of direct aqueous carbonation. We evaluated the carbonation performance of three types of steel slag at temperatures below 100°C using a gas–liquid–solid reaction system. The slag with the highest CO2 sequestration capacity was chosen for a systematic evaluation of the effects of operating conditions on carbonation efficiency. Thermodynamic analysis indicated that the reactivity of CaO and Ca(OH)2 with CO2 exceeded that of CaO•SiO2 and 2CaO•SiO2. Under conditions of 85°C, a particle size less than 75 μm, an initial CO2 pressure of 0.5 MPa, a liquid-to-solid ratio of 5 mL/g, and a stirring speed of 200 rpm, the steel slag achieved a sequestration capacity (K) of 283.5 gCO2/kg and a carbonation efficiency (ζCa) of 51.61%. Characterization of the slag before and after carbonation using X-ray diffraction, SEM‒EDS, thermogravimetric analysis, and Fourier transform infrared spectrometry confirmed the formation of new carbonates. Mechanistic analysis revealed that the rate-limiting step initially involved the mass transfer of CO2, transitioning to Ca2+ mass transfer as time progressed. Our research provides a viable technique for CO2 capture and a beneficial approach for reutilizing waste steel slag. Furthermore, solid residues after capturing CO2 have the potential for conversion into carbon-negative building materials, offering a sustainable strategy for steel companies and other enterprises with high carbon emissions.

Detecting cracks in structural health monitoring is crucial for ensuring infrastructure safety and longevity. Using drones to obtain crack images and automate processing can improve the efficiency of crack detection. To address the challenges posed by the limited computing resources of edge devices in practical applications, we propose CrackScopeNet, a lightweight segmentation network model that simultaneously considers local and global crack features, suitable for deployment on drone platforms with limited computational power and memory. CrackScopeNet features a multi-scale branch to improve sensitivity to cracks of varying sizes without substantial computational overhead and a stripe-wise context attention mechanism to enhance the capture of long-range contextual information, mitigating the interference from complex backgrounds. Experimental results on CrackSeg9k dataset demonstrate that CrackScopeNet leads to a significant improvement in prediction performance, with the highest mean intersection over union (mIoU) scores reaching 82.12%, while maintaining a lightweight architecture with only 1.05M parameters and 1.58G floating point operations (FLOPs). Besides, CrackScopeNet excels in inference speed on edge devices without GPU because of its low FLOPs. CrackScopeNet contributes to the development of efficient and effective crack segmentation networks, suitable for practical structural health monitoring applications using drone platforms.

Expansion tube is ideal energy absorber which dissipates kinetic energy through plastic deformation and friction. There is an urgent need to understand the influence of key parameter, e.g. semi angle, tube material, and friction coefficient, on the mechanical response and energy absorption characteristics of expansion tube. In the present work, the material properties of the tubes were tested under quasi-static loading condition, and the numerical simulations were carried out by using commercial software ABAQUS. Based on the validated finite element simulation, all the semi angle, tube material, and friction have significant effects on the energy absorption capacity of expansion tube. The expansion tube with high tensile stress of parent material have high energy absorption capacity, while the specific energy absorption is linear with the tensile stress/density of tube material. This work would give a guidance to the structural design and parent materials selection for expansion tubes.

Carbon tax policies (CTP) are globally acknowledged for curbing energy consumption and emissions. Despite global adoption, China's reluctance to embrace a carbon tax, possibly due to effectiveness and public acceptance concerns, is notable. This study employs Choice-Based Conjoint Analysis to gauge Shanghai residents' preferences on four CTP attributes. Among Shanghai's populace, the annual cost of the carbon tax policy ranks highest (48.87%), followed by implementation transparency (24.72%), revenue utilization (16.68%), and policy implementers (9.73%). Notably, Shanghai residents exhibit an average annual willingness to pay of 1435.28 CNY, indicating increased acceptance. Enhanced public awareness of carbon tax policies significantly boosts willingness to pay, augmenting carbon tax revenues and fostering low-carbon technology development. Additionally, transparency improvements in carbon tax policy yield notable increases in willingness to pay, underscoring the link between understanding CTP and its perceived importance. These findings highlight the potential of carbon tax policies in advancing sustainability and transitioning to low-carbon economies.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

Although Eulerian approaches are standard in computational acoustics, they are less effective for certain classes of problems like bubble acoustics and combustion noise. A different approach for solving acoustic problems is to compute with individual particles following particle motion. In this paper, a Lagrangian approach to model sound propagation in moving fluid is presented and implemented numerically, using three meshfree methods to solve the Lagrangian acoustic perturbation equations (LAPE) in the time domain. The LAPE split the fluid dynamic equations into a set of hydrodynamic equations for the motion of fluid particles and perturbation equations for the acoustic quantities corresponding to each fluid particle. Then, three meshfree methods, the smoothed particle hydrodynamics (SPH) method, the corrective smoothed particle (CSP) method, and the generalized finite difference (GFD) method, are introduced to solve the LAPE and the linearized LAPE (LLAPE). The SPH and CSP methods are widely used meshfree methods, while the GFD method based on the Taylor series expansion can be easily extended to higher orders. Applications to modeling sound propagation in steady or unsteady fluids in motion are outlined, treating a number of different cases in one and two space dimensions. A comparison of the LAPE and the LLAPE using the three meshfree methods is also presented. The Lagrangian approach shows good agreement with exact solutions. The comparison indicates that the CSP and GFD method exhibit convergence in cases with different background flow. The GFD method is more accurate, while the CSP method can handle higher Courant numbers.

Semisolid casting can provide excellent castings, but the nature of the pore-forming mechanisms has not been properly clarified. In the current communication, it was suggested that hydrogen precipitated during slurry making might have a decisive role in the formation of both gas and shrinkage porosity. Intensive stirring at the end of the slurry making process may act as a degassing step. Without the intense stirring, structures of primary slurry particles form around the hydrogen pores, strongly affecting pore formation and feeding during the intensification stage.

In order to explore the effect of Wickerhamomyces on the production of flavor compounds in Xiaoqu Baijiu, this study examined the correlation between the fungal communities in Xiaoqu and ester compounds. It was hypothesized that Wickerhamomyces contributes to the aroma of Xiaoqu. Enhanced fermentation methods were used to validate the role of Wickerhamomyces in Xiaoqu Baijiu brewing. Compared to traditional Xiaoqu, enhanced fermentation significantly increased the acidity of fermented grains and starch utilization rate (P<0.05). The fungal communities in fermented grains were analyzed by high-throughput sequencing technology. The dominant fungi in both control and test groups were Saccharomyces, Cyberlindnera, Rhizopus, and Meyerozyma, with Wickerhamomyces replacing Saccharomymycopsis in the enhanced group. Flavor compounds in the fermentation experiments were analyzed, revealing that ethyl acetate content in Xiaoqu Baijiu increased by 949.94 mg/L in the test group, while isoamyl alcohol decreased by 23.62 mg/L and isobutanol decreased by 34.81 mg/L. Functional prediction analysis using PICRUSt2 confirmed a higher relative abundance of enzymes involved in ethyl acetate metabolism and a lower relative abundance of enzymes involved in higher alcohol metabolism in the test group. These findings demonstrate that Wickerhamomyces enhances ethyl acetate production and reduces higher alcohols during Xiaoqu Baijiu brewing, offering a theoretical foundation for enhancing the quality of Xiaoqu Baijiu.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Arthropods, the most abundant group in ecosystems, play crucial roles in human production. Soil physicochemical properties reflect soil health and are linked to arthropods through cascading effects. Gravel-sand mulching, commonly practiced in dry farming regions, initially aids in water retention and temperature regulation. However, long-term cultivation can lead to land degradation and habitat fragmentation. This study aimed to investigate field systems using multiple comparison, linear, and nonlinear correlation analyses to explore the effects of different tillage durations on soil properties and arthropod diversity under gravel-sand mulching. Results indicate that arthro-pod diversity was lower while the fields maintained better soil fertility than the desert steppe. Both soil fertility and arthropod diversity declined significantly with increased years of cultivation. Mantel tests revealed no significant response of desert steppe arthropods to the altered soil properties of gravel-sand mulched fields. However, the Generalized Additive Model analysis indicated significant linear correlations between arthropod occurrence and total nitrogen (positive), available phosphorus, and water content (negative). Arthropod abundance showed significant nonlinear correlations with total potassium, alkali hydrolyzable nitrogen, and organic matter (OM), with OM changes having the most pronounced impact. Thus, gravel-sand mulching can maintain soil fertility over time but at the expense of local arthropod diversity.

Leaf photosynthetic pigments play a crucial role in evaluating nutritional elements and physiological states. In facility agriculture, it is vital to obtain rapidly and accurately the pigment content and distribution of leaves to ensure precise water and fertilizer management. In our research, we utilized chlorophyll a (Chla), chlorophyll b (Chlb), chlorophyll (Chll), and carotenoid (Caro) as indicators to study the variations in leaf position of Lycopersicon esculentum Mill. Under 10 nitrogen concentration applications, a total of 2610 leaves (435 samples) were collected using visible-near infrared hyperspectral imaging (VNIR-HSI). In this study, a "coarse-fine" screening strategy was proposed by using competitive adaptive reweighted sampling (CARS) and iteratively retained informative variable (IRIV) algorithm to extract characteristic wavelengths. Finally, simultaneous and quantitative models were established using partial least squares regression (PLSR). The CARS-IRIV-PLSR was used to create models to achieve a better prediction effect. The coefficient determination (R2), root mean square error (RMSE), and ratio performance deviation (RPD) were predicted to be 0.8240, 1.43, 2.38 for Chla, 0.8391, 0.53, 2.49 for Chlb, 0.7899, 2.24, 2.18 for Chll, and 0.7577, 0.27, 2.03 for Caro, respectively. The combination of these models with the pseudo-color image allowed for a visual inversion of the content and distribution of pigment. These findings have important implications for guiding pigment distribution, nutrient diagnosis, and fertilization decisions in plant growth management.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

Functional partially linear regression model, contains a functional linear part and a non-parametric part, in which testing the linear relationship between the response and the functional predictor is of fundamental importance. When functional data cannot be approximated with a few principal components, based on a pseudo estimate for the unknown non-parametric component, we develop a U-statistic of order-two in this paper. Under some regularity conditions, we use the martingale central limit theorem to prove that the proposed test statistic is asymptotically normal. The finite sample performance with simulation studies and real data application are assessed to verify the proposed test procedure.

Microcystis-dominated cyanobacterial blooms (MCBs) frequently occur in freshwaters worldwide due to massive Microcystis colonies formation and severely threaten human and ecosystems health. Quorum sensing (QS) is a direct cause of Microcystis colonies formation, possibly regulating MCBs occur and Microcystis population behaviors [1, 2]. Many novel findings in fundamental knowledge of Microcystis QS phenomenon and the signaling molecules have been documented. However, little effort has devoted to comprehensively summarize and discuss research progresses and exploration direction on QS signaling molecules-mediated QS system in Microcystis. This article summarizes action process of N-acyl homoserine lactones (AHLs) as major signaling molecules in Microcystis and discussed the detailed roles of AHLs-mediated QS system in cells aggregation, colonies formation, ecological adaptability and competitive advantage. And the progress was summarized in research on the QS mechanism in Microcystis. Compared to other QS system, the LuxI/LuxR-type QS system is more likely to found in Microcystis. Also, we introduced Quorum quenching (QQ) — QS blocking process in Microcystis, with emphasizing on the potential of QS inhibitors in MCBs control. Finally, in response to the research deficiencies and gaps in Microcystis QS and QQ, we proposed several future research directions in these fields. This review may deepen the understanding of Microcystis QS knowledge and provide theoretical guidance for the development of strategies to monitor, control and harness MCBs.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

The purpose of this paper is to construct an evaluation system for AI painting software based on generative adversarial network technology, which optimizes the performance of the related software in terms of functionality, ease of use, system performance and safety. The results of the questionnaires are statistically analyzed. In addition, exploratory factor analysis was supported to extract the data of the study, which was ultimately used to calculate the weight and importance of each index through fuzzy hierarchical analysis method. The study constructed an evaluation system for AI painting software based on generative adversarial network technology, including 16 indicators of functionality, 16 indicators of ease of use, 7 indicators of system performance, and 8 indicators of safety respectively that their alpha coefficients were 0.882, 0.962, 0.932, 0.932, and 0.932, respectively. In addition, the accumulated explanatory variances of their coefficients were 84.405%, 84.897%, 84.013%, and 72.606%, respectively, 73.013%, and 72.606%, respectively. It is clear that the items included in each of the indicators are homogeneous, with a high degree of internal consistency. This paper suggests that the development of AI painting software focusing on functionality, ease of use, system performance and safety can enhance the market competitiveness of the software.

Color image binarization plays a pivotal role in image preprocessing work, significantly impacting subsequent tasks, particularly in text recognition. This paper concentrates on Document Image Binarization (DIB), aiming to separate a image into foreground (text) and background (non-text content). Through a thorough analysis of conventional and deep learning-based approaches, we conclude that prevailing DIB methods leverage deep learning technology. Furthermore, we explore the receptive fields pre- and post-network training to underscore the Transformer model's advantages. Subsequently, we introduce a lightweight model based on the U-Net structure, enhanced with the Mobile ViT module to better capture global information features in document images. Given its adeptness at learning both local and global features, our proposed model exhibits superior performance on two standard datasets (DIBCO2012 and DIBCO2017) compared to state-of-the-art methods. Notably, our proposed DIB method presents a straightforward end-to-end model devoid of additional image preprocessing or post-processing. Moreover, its parameter count is less than a quarter of the HIP'23 model, which achives best results on three datasets(DIBCO2012, DIBCO2017 and DIBCO2018). Finally, two sets of ablation experiments were conducted to verify the effectiveness of the proposed binarization model.

In this study, a novel and efficient method was developed for the extraction of total flavonoids from Flos Sophorae Immaturus (FSI) using ultrasound-assisted deep eutectic solvent (UAE-DES). Different DES formulations were first investigated and choline chloride/1,2-propanediol (ChCl/PD) was identified as the optimal solvent due to its highest flavonoid yield. The extraction process was optimized through single factor experiments and response surface methodology (RSM). An extraction temperature of 68 °C, a sonication time of 41 minutes, a water content of 21% and a liquid-solid ratio of 21 mL/g were identified as the optimal conditions. Under these conditions, a maximum flavonoid yield of 378.77 mg RE/g DW was achieved. The crude extract was further purified using a macroporous D-101 resin, resulting in a flavonoid extract with a purity of 83.11 ± 3.54%. The antioxidant activity of the purified extract (FSPE) was evaluated using DPPH and ABTS radical scavenging assays, showing significant antioxidant properties with IC50 values of 52.50 μg/mL and 49.47 μg/mL, respectively. The UAE-DES method developed in this study not only significantly improves the extraction yield of flavonoids from FSI, but is also in line with sustainable and environmentally friendly practices. This method offers an environmentally friendly, efficient and scalable approach for the extraction of bioactive compounds from medicinal plants and has potential applications in the food, pharmaceutical and dietary supplement industries.

Integrating ecosystem services (ESs) to delineate ecological functional zones (EFZs) is a fundamental work in terrestrial spatial planning and ecosystem management. However, existing studies have largely overlooked the refinement of EFZs at local scales, which hinders targeted and multi-scale ecosystem management. This study introduced a "two-step refinement zoning method" to address this gap, first using the self-organizing feature mapping method to delineate EFZs based on ESs at a township scale, and then applying hotspot overlay analysis to identify hotspots of dominant ESs within EFZs at a village scale. By overlaying the outcomes of these two steps, EFZs can be further graded by designating villages with hotspots of dominant ESs as level I and those without as level II. The proposed method was applied in Wuhan City, dividing it into five types of EFZs with different ESs combinations and land use compositions. Furthermore, 5.23% of villages were identified as Level I of EFZs, serving as advantageous areas of dominant ESs in the study area. On this basis, diversified management strategies and conservation priorities were proposed. This study provides a theoretical and methodological reference for terrestrial spatial planning and sustainable ecosystem management.

In view of the fact that the field monitoring information can more intuitively and accurately reflect the stability state of slopes, this paper takes the warning threshold of slope deformation rate monitoring as the slope stability evaluation standard, and puts forward a method for solving the safety coefficient of rocky slopes. The discrete element method 3DEC, which is suitable for rocky slopes, is selected as the numerical calculation tool, and the convergence criterion of its strength reduction method is modified to the slope deformation rate threshold, and the method is realized by the bifurcation method through its built-in FISH programming language. The results of the classical case show that, by selecting the slope deformation rate threshold in the appropriate interval, the results of this paper's method are very close to those of the finite unit stress method and the limit equilibrium method, which verifies the reliability of this paper's method. Further, the method of this paper is applied to an open-pit mine slope project, based on the slope deformation on-site monitoring data, through the time series prediction method to determine the slope deformation rate warning threshold, using the threshold as an evaluation criterion to solve the slope's coefficient of safety, the calculation results show that: the slope's coefficient of safety in natural working conditions is 1.086, basically stable, suffered from continuous rainfall, the slope body is gradually saturated, the slope's coefficient of safety is reduced to 0.987, the slope's safety is reduced to 0.987. After continuous rainfall and gradual saturation of the slope, the coefficient of safety decreased to 0.987, destabilizing and destroying, which is consistent with the site conditions.

There are few longitudinal studies on the association between dietary vitamin C and sleep disorders. The aim of this study was to investigate the association between dietary vitamin C intake and various types of sleep disorders, including sleep apnea and insomnia, as well as recommended dietary intakes. A total of 68,221 participants from the UK Biobank were enrolled in the study. Dietary vitamin C intake was calculated by a 24-hour dietary recall questionnaire. We used Cox regression model to assess the association between dietary vitamin C and sleep disorders and restricted cubic spline models to explore potential nonlinear relationships. Stratified analyses and sensitivity analyses were also performed to further test the results. The results showed that vitamin C intake at the Q4 level (132.88-191.51 mg/d) was significantly protective against sleep disorders with an HR (95% CI) of 0.78 (0.65-0.94), and against sleep apnea with an HR (95% CI) of 0.75 (0.62-0.92). The protective effect remained significant in stratified analyses of men and age ≤60 years, and the results were robust in sensitivity analyses. Adequate dietary vitamin C intake may have a protective effect in preventing sleep disorders.

Pipelines extend thousands of kilometers to transport and distribute oil and gas. Given the challenges often faced with corrosion, fatigue, and other issues on steel pipes, the demand for glass fiber reinforced plastics (GFRP) pipes is increasing in the oil and gas gathering and transmission systems. However, the medium transported through these pipelines contains multiple acid gases such as CO2 and H2S, as well as ions including Cl-、Ca2+、Mg2+、SO42-、CO32- and HCO3-. These substances can cause a series of problems, such as aging, debonding, delamination, and fracture. In this study, a series of aging damage experiments were conducted on V-shaped GFRP pipes with depths of 2mm and 5mm. The aging and failure of GFRP were studied under the combined effects of external force and acidic solution using acoustic emission (AE) techniques. It was found that the acidic aging solution promoted matrix damage, fiber/matrix desorption, and delamination damage in GFRP pipes over a short period. However, the overall aging effect was relatively weak. Based on the experimental data, the SSA-LSSVM algorithm was proposed and applied to the damage pattern recognition of GFRP. An average recognition rate of up to 90% was achieved, indicating that this method is highly suitable for analyzing AE signals related to GFRP damage.

This paper represents the first investigation into the consensus problem of linear time-varying multi-agent systems utilizing an event-triggered communication scheme. First, a general event-triggered consensus control scheme is proposed for a general category of linear time-varying multi-agent systems. Under some suitable assumptions, it is demonstrated that all agents’ states will converge exponentially, with Zeno behaviour being ruled out. Second, the consensus problem in a network of linear time-varying multi-agent systems with a spanning tree is investigated using the proposed control strategy. It demonstrates that the consensus issue for the specified system can be reformulated as a stabilization problem for an error system through a time-varying linear transformation. Then, the event-triggered consensus problem is just a special instance of the general event-triggered consensus problem mentioned above. Finally, to illustrate the efficacy of the event-triggered method proposed in this study, simulation results are shown.

At present, farmland abandonment（FA）is a severe phenomenon in China, imposing a serious restriction on agricultural production. In this context, it is of great significance to explore the logical relationship between high-standard farmland construction (HSFC) and FA to optimize land resource allocation and guarantee national food security. Based on 838 samples of farmers in the main rice production area of the Yangtze River Basin in China, this paper employs the Tobit model, the mediating effect model, and the moderated mediating effect model to analyze the impact of HSFC on FA at the micro level. The results show that (1) HSFC inhibits FA, and FA proportion decreases by 1.14% for every 1% increase in HSFC proportion, and the robustness test and endogeneity treatment also yield consistent conclusions. (2) Agricultural socialization services (ASS) play a positive mediating role in the influence path. HSFC promotes farmers' purchase of ASS, which in turn inhibits FA. (3) The agricultural labor transfer distance (ALTD) plays a positive moderating role in the relationship between HSFC and FA. The farther the distance, the more likely HSFC can promote farmers' purchase of ASS and inhibit FA. The results provide enlightenment on how to precisely implement HSFC policy, that is, to inhibit FA by improving the construction of high-standard farmland and the post-construction management as well as protection system. Moreover, this study helps guiding the development of ASS and optimizing the institutional environment for agricultural labor transfer, creating conditions for agricultural scale management.

Sunflower is one of the oil crops and its planting areas was listed behind Soybean, peanut and rapeseeds in China. It will encounter different kind of diseases during planting, thus limited the seeds yield. Fusarium species are the major threat to different crops nowadays, it is very important to identify the species caused diseases on different hosts, so that the potential control measures may be explored. In Inner mongolia, Sunflower Disk Rot (SDR) was found in different sunflower planting field, the average infection ratio around 8.50%, typically in some verieties, its infection ratio reach to 11.67%. The diseased receptacle were collected from different locations and Koch’s postulate was conducted. The results showed that Fusarium verticillioides was the main causal agent caused SDR. Fungicide toxicity tests shown that Fludioxonil and Flutolanil were screened out from six fungicides for controlling F. verticillioides, with EC50 values of 0.05 µg/mL (R = 0.9825) and 0.96 µg/mL (R = 0.9964) , respectively. This is the first report of SDR caused by F. verticillioides, and it will alert sunflower reseachers to include SDR in the disease list, so as to control sunflower diseases with integrated management strategy successfully.

The new digital infrastructure has become an important basis for the green development of agriculture. This paper selects provincial sample data from 2006 to 2022, constructs an indicator system to measure new digital infrastructure and agricultural green total factor productivity, and explores how new digital infrastructure can promote agricultural green development. The results show that: (1) the new digital infrastructure has a significant role in promoting the green development of agriculture, and this conclusion is still valid after processing endogeneity and heteroscedasticity; (2) Technology and land factors play an intermediary role in the promotion of green agricultural development by the new digital infrastructure, that is, the new digital infrastructure helps to improve the quality and technical level of cultivated land and thus promote green agricultural development; (3) Labor force factors optimize the mediating role of technology factors, that is, the higher the quality of labor force, the stronger the role of the new digital infrastructure in promoting the green development of agriculture through the technological path; (4) The effect of new digital infrastructure on the green development of agriculture is obviously heterogeneous, and the effect is more obvious in northwest China and the regions with lower marketization level, higher environmental regulation level. This study is helpful to clarify the relationship between new digital infrastructure and agricultural green development in China, and provide corresponding policy suggestions for promoting regional agricultural green development.

Aim: We estimated the correlation between serum bilirubin concentrations and insulin resistance in advanced maternal age without diabetes mellitus. Method: The cross-sectional study involved consecutive 50 women of advanced maternal age without diabetes mellitus, and insulin resistance (IR) was diagnosed according to the homeostatic model assessment insulin resistant (HOMA-IR) formula and the cut-off point was set to more than 2.5. Serum bilirubin and HOMA-IR were compared between the IR (+) and IR (-) groups. Results: We found that serum bilirubin levels in the IR subjects were significantly decreased compared to those without IR (p = 0.0252). Serum bilirubin concentrations were negatively correlated with the weight and the fasting insulin concentrations in all subjects (r=−0.282, p=0.047, r=-0.424, p=0.002). Additionally, serum bilirubin had a negatively correlation with HOMA-IR (r = -0.410, p = 0.003) in all subjects. The multiple linear regression analysis found that serum total bilirubin levels were independently correlated with HOMA-IR (beta = -0.392, p= 0.015) in these subjects. Conclusions: The study demonstrated that serum bilirubin concentrations had negatively correlation with insulin resistance in advanced pregnant women without diabetes mellitus, and decreased serum bilirubin may forebode increased gestational diabetes mellitus risk in our study population.

This study investigated the effectiveness of virtual reality (VR) technology in table tennis education compared to traditional training methods. A 12-week randomized controlled trial was conducted with 120 participants divided equally between VR and traditional training groups. Performance metrics, learning motivation, and satisfaction were assessed at regular intervals. Results demonstrated significant advantages of VR training, with the VR group showing superior improvements in serve accuracy (23.5% vs. 15.8%, p < 0.001), rally endurance (increase of 8.2 vs. 5.7 shots, p < 0.01), and overall skill scores (18.7 vs. 13.2 points improvement, p < 0.001). The VR group also exhibited higher increases in learning motivation (23.5% vs. 12.8%, p < 0.001) and satisfaction (31.5% vs. 18.7%, p < 0.001). Subgroup analysis revealed particular benefits for novice players and younger participants. These findings suggest that VR technology offers a promising approach to enhance table tennis education, potentially revolutionizing sports training methodologies. Future research should focus on long-term skill retention and the optimization of VR training protocols.

Forest fires can occur suddenly and have significant environmental, economic, and social consequences. Timely and accurate evaluation and prediction of their progression, particularly the spread speed in difficult-to-access areas, are essential for emergency management departments to proactively implement prevention strategies and scientifically extinguish fires. This paper provides a comprehensive analysis of advanced technologies for predicting forest fire spread in China and globally. Incorporating remote sensing (RS) technology and forest fire science as the theoretical foundation, and utilizing the Wang Zhengfei forest fire spread model as the technical framework, this study constructs a forest fire spread model based on remote sensing interpretation. The model optimizes the method for acquiring parameters and enhances algorithm accuracy. By considering regional landforms (ridge lines, valley lines, slopes) and vegetation coverage, this paper establishes visual interpretation markers for identifying hotspots within the spread model. Utilizing statistical data from pixels within the fire line zone transforms the methodology for predicting forest fire spread speed, resulting in greater accuracy compared to conventional fixed-point predictions. Finally, the model was applied to the case of a forest fire in Mianning County, Sichuan Province, China and verified using high-time resolution mid-infrared image data and previous research findings. The results demonstrate that the predicted fire spread area from this RS-enabled model is consistent with both high-time resolution geostationary satellite data and previous research outcomes, indicating high reliability. This model can provide crucial fire spread information to relevant emergency departments, enabling effective preemptive measures and scientific firefighting strategies.

The existences of the N→C dative bonds in the complexes between N-containing molecules and fullerenes have been verified both theoretically and experimentally. However, finding stable N→C dative bonds is still a highly challenging task. In this work, we investigated computationally the N→C dative bonds in the complexes formed by fullerene C60 with 1,2,5-chalcogenadiazoles, 2,1,3-benzochalcogenadiazoles and 1,2,4,5-chalcogenatriazoles, respectively. It was found that the N→C dative bonds are formed along with the formation of the N–Ch···C (Ch = S, Se, Te) chalcogen bonds. In the gas phase, from S-containing complexes through Se-containing complexes to Te-containing complexes, the intrinsic interaction energies become more and more negative, which indicates that the N–Ch···C chalcogen bonds can facilitate the formation of the N→C dative bonds. The intrinsic interaction energies are compensated by the large deformation energy of fullerene C60. The total interaction energies of Te-containing complexes are negative, while both of the total interaction energies of S-containing complexes and Se-containing complexes are positive. This means that the N→C dative bonds in the Te-containing complexes are more easily observed in experiments in comparison with those in the S-containing complexes and Se-containing complexes. This study provides a new theoretical perspective on the experimental observation of the N→C dative bonds in the complexes involving fullerenes. Further, the formation of stable N→C dative bonds in the complexes involving fullerenes can significantly change the properties of fullerenes, which will greatly simulate and expand the application range of fullerenes.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Obesity and chronic inflammation are well-known risk factors for cancer. Interleukin-33 (IL-33) functions in inflammatory diseases, particularly those related to obesity and cancer. However, the correlation and molecular mechanisms linking IL-33, obesity, and cancer remain unclear. IL-33 is a nuclear cytokine released as an alarm signal when cells are damaged or stressed. It is expressed in epithelial, endothelial, and fibroblast-like cells during normal conditions and in-flammation. When IL-33 is present, immune cells expressing the IL-1RL1/ST2 receptor are alerted in response to tissue damage or cell injury. Research on IL-33 and its correlation with obesity has revealed improvements in inflammatory and metabolic changes associated with obesity. IL-33 can have both pro-tumorigenic and antitumorigenic effects, depending on the cellular content, in-flammatory environment, expression levels, and bioactivity of IL-33. This review will discuss the various functions of IL-33 in obesity-driven inflammation and cancers and how they intersect.

Currently, urban renewal activities in China are booming. And promoting the renovation of public buildings is the key due to its large scale, high cost and significant impact to the nature and social environment. To reduce the ambiguity and uncertainty in evaluating the potential for renewal of existing public buildings, a renewal potential evaluation model combining game theory combination weighting method and cloud model theory is proposed. The paper constructs a comprehensive evaluation index system based on relevant standards and literature. Game theory is used to optimize the weights obtained by AHP and entropy weight methods to obtain a combined weight. MATLAB programming is used to calculate the comprehensive cloud parameters of the evaluation index for the potential renewal of existing public buildings and therefore generate cloud Graphs. Through case study in Nanjing of China, it has been demonstrated that the combination empowerment cloud model can objectively reflect the relationship between the fuzziness and randomness of evaluation indicators for public building renewal potential. The expression of cloud Graphs can intuitively reflect the magnitude of renewal and renovation potential and the degree of uncertainty in evaluation results. The research result provides useful references for the sustainable utilization of building resources in the era of building.

Domain generalization has led to remarkable achievements in Hyperspectral Image (HSI) classification. Inspired by contrastive language-image pre-training (CLIP), the language-aware domain generalization method has been explored to learn cross-domain-invariant representation. However, existing methods face some challenges: 1) The weak capacity to extract long-range contextual information and inter-class correlation. 2) Due to the inadequacies of the large-scale pre-training for HSI data, the spatial-spectral features of HSI and linguistic features can not be straightforwardly alignment. To address the above problems, a novel network has been proposed with a CLIP framework, which consists of an image encoder, based on an encoder-only transformer to obtain the global contextual information and inter-class correlation, a frozen text encoder, and a cross-attention mechanism, named Linguistic-Interact-with-Visual Engager (LIVE), enhances the interaction between two modalities. Extensive experiments demonstrating superior performance over state-of-the-art methods in HSI Domain Generalization with a CLIP framework.

The impacts of inflation on international finance are generally reflected in the decline of buying power, risks of investment and deposit loss from currency devaluation. For the purpose of optimized allocation and management of asset values, i.e., annual income or research grants, a framework of a three-level model for static financial management is presented to maximize banking interests, bonuses, and the remaining balance after spending necessary expenditures. Meanwhile, in retrospect to higher-level financial inflation, strategies of dynamic investment, i.e., posing regular tests of flipping coins, exploiting variations of the currency exchange rate, as well as applying the theory of broad money, are presented to increase the appreciation rate of net assets in and post the era of COVID-19. Quantitative evaluations in case studies verify the feasibility of improving the financial situation, indicating broader applications for budgeting and investing when US inflation rate is below 3.0%. Besides, combining approaches of static and dynamic strategies, the expected annual growth rate of individual zero-risk asset investment is predicted as within the range of 8.30~9.62% according to budgeted appreciation on net assets in 12 months, which is capable of overcoming negative impacts from higher level annual inflation, i.e., those as highest as 8.01% in the Year 2022.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

Tsallis entropy has been widely used in image thresholding because of its non-extensive properties. The non-extensive parameter q contained in this entropy plays an important role in various adaptive algorithms and has been successfully applied in bi-level image thresholding. In this paper, the relationships between parameter q and pixels’ long-range correlations have been further studied within multi-threshold image segmentation. It is found that the pixels’ correlations are remarkable and stable for images generated by a known physical principle, such as infrared images and medical CT images. And the corresponding non-extensive parameter q can be evaluated by using self-adaptive Tsallis entropy algorithm. The results of this algorithm are compared with those of Shannon entropy algorithm and the original Tsallis entropy algorithm, in terms of quantitative image quality evaluation metrics PSNR (Peak Signal-to-Noise Ratio) and SSIM (Structural Similarity). Furthermore, we observed that for image series with the same background, the q values determined by the adaptive algorithm are consistently kept in a narrow range. Therefore, similar or identical scenes during imaging would produce similar strength of long-range correlations, which provides potential applications for unsupervised image processing.

This article systematically studied the A-optimal designs of a high-order mixture central polynomial model, which is an advancement of the research results for the A-optimal design of the most recent third-order mixture central polynomial model and a more accurate response surface model. This article is based on the simplex center design, obtaining measurement values at various design points, and verifying them through the A-optimal equivalence theorem. We also compare the A-efficiency of designs through examples, which can be applied to the A-optimal precise design of the fourth-order mixture model.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

This study presents a novel Fe-CNs-P/S carbon composite material, synthesized by doping elements P and S into NH2-MIL-101 (Fe) using carbonization method. The material's application in sustainable water treatment was evaluated, focusing on its effectiveness in activating persulfate for pollutant degradation. The research thoroughly investigates the synthesis process, structural characteristics, and performance in degrading pollutants. Results indicate that Fe-CNs-P/S-5 with 50% P and S co-doping is higher than that of other samples, where the degradation rate of TC in 30min is as high as 98.11% under the optimum conditions, that is temperature at 25 ℃, 0.05 g/L of catalyst concentration, and 0.2 g/L of PMS concentration. The composite material demonstrates robust versatility and stability, maintaining high degradation efficiency across multiple organic pollutants, with no significant reduction in catalytic performance after four cycles. Furthermore, the free radical quenching experiments displays that the singlet oxygen 1O2 is the main active species. It is demonstrated that the doping of P and S play a role in the enhancement of PMS activation over the Fe-CNs-P/S catalyst. This material demonstrates remarkable efficacy in treating a range of organic contaminants and exhibits excellent reusability, presenting a promising approach for enhancing sustainability in water treatment applications.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Elderly individuals frequently perceive companion robots devoid of warmth, resulting in a reluctance to accept these robots' services. This perception has become a significant barrier to the introduction of companion robots into households. To address this issue, this study employs KE methods to translate the elderly's need for warmth perception from companion robots into elements of modelling design. Initially, 20 pairs of affective words and 22 sample images of companion robots were chosen. The "rational-emotional" and "dim-bright" dimensions were identified as positively influencing the elderly's warmth perception of companion robots through SD method analysis. Subsequently, a hierarchical analysis table was established, with warmth perception as the root layer, modelling style and color matching as the basic layer, "rational-emotional" and "dim-bright" as the expansion layer, and the eight characteristic elements of companion robots as the morphological layer. The link between affective imagery and design elements was then established from the sample robots with higher warmth perception scores. Based on the correlation between the two, various design schemes were formed through random combinations. Finally, the design schemes were evaluated using the warmth perception scale, and the warmth perception scores of each sample model were obtained. This research provides design references for designing companion robots for the elderly with a "sense of warmth".

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.