Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

A nanocomposite rod-shaped structure with single-walled carbon nanotube (SWCNT) embedded in polypyrrole (PPy) doped with nonafluorobutanesulfonic acid (C4F), SWCNT/C4F-PPy, was synthesized using emulsion polymerization. The hybrid ink was then directly coated on a polyimide film interdigitated with the Cu/Ni/Au electrodes via a screen-printing technique to create a flexible film sensor. The sensor film showed a response of 1.72% at 25 °C/atmospheric pressure when acetone gas of 5 ppm was injected, which corresponds to almost 95% compared to the Si wafer-based array interdigitated with the Au electrode. Additionally, C4F was used as a hydrophobic dopant of PPy to improve the stability of humidity and to produce a highly sensitive film-type gas sensor that provides stable detection even in humid conditions.

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in MV-class bushing aimed to detect partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signals. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) principle for voltage measurement and D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kV) were less than 0.2% and 10 minutes, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

This study was conducted on elderly over 65 years of age to verify that healing garden activities control stress in the elderly. The experimental group performed garden activities once a week for 12 weeks, 2 hours each, and the control group continued their daily lives. Each group's cumulative stress at the beginning and end, total power (TP), the standard deviation of the normal-to-normal interval (SDNN), and root mean square differences of successive R-R intervals (RMSSD) were measured using a stress index meter, u-bio MACPA. As a result of the analysis, the experimental group had a statistically significant decrease in cumulative stress compared to the control group, and TP significantly increased compared to the control group. SDNN and RMSSD of the experimental group increased, respectively, and the control group decreased, respectively, but it was not statistically significant. The fact that cumulative stress decreased, and stress evaluation indicators increased shows that daily stress can be controlled through healing garden activities. This confirms that the value of the garden can extend to healing.

A lead zirconate titanate [PZT;Pb(Zr_0.52Ti_0.48)O₃] layer embedded infrared (IR) detector decorated with wavelength-selective plasmonic crystals has been investigated for high-performance non-dispersive infrared (NDIR) spectroscopy. A plasmonic IR detector with an enhanced IR absorption band has been designed based on numerical simulations, fabricated by conventional microfabrication techniques, and characterized with a broadly tunable quantum cascade laser. The enhanced responsivity of the plasmonic IR detector at specific wavelength band has improved the performance of NDIR spectroscopy and pushed the limit of detection (LOD) by an order of magnitude. In this paper, a 13 fold enhancement in the LOD of a methane gas sensing using NDIR spectroscopy is demonstrated with the plasmonic IR detector.

As symbionts of fungi and algae, lichens produce a variety of secondary products which pharmacological activities. This study aimed to investigate the anti-inflammatory activities of Heterodermia hypoleuca and its main compound, atraric acid. The results confirmed that atraric acid could regulating induced pro-inflammatory cytokine, nitric oxide, induced nitric oxide synthase and cyclooxygenase-2 expression by lipopolysaccharide (LPS)-stimulated RAW264.7 cells. Means while, atraric acid down-regulated expression of phosphorylated IκB, ERK and nuclear factor kappa B (NFκB) signaling pathway to exhibit anti-inflammatory effects in LPS-stimulated RAW264.7 cells. Based on these results, the anti-inflammatory effect of atraric acid during LPS-induced endotoxin shock in a mouse model was confirmed. In the atraric acid treated-group, cytokine production was decreased in the peritoneum and serum, and each organ damaged by LPS-stimulation was recovered. These results show that atraric acid has an anti-inflammatory effect and its molecular mechanism may be involved in the inactivation of the ERK/NFκB signaling pathway, demonstrating its value as a potential therapeutic for inflammatory diseases.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

To determine the mode of action of the effects of phytoalexins in soybeans, we analyzed enzyme inhibition kinetics using Michaelis–Menten plots and the Lineweaver–Burk plots. The results showed that glyceollin showed competitive inhibition, genistein showed noncompetitive, daidzein was uncompetitive, and luteolin showed a mixed mode of action. The Ki values were determined using a Dixon plot as: glyceollin, 18.99; genistein, 15.42; luteolin, 16.81; and daidzein, 9.99 μM, respectively. Furthermore, potential synergistic effects between glyceollin and the three designated polyphenols were investigated. A combination of glyceollin and luteolin (the ratio of 3:7 of glyceollin and luteolin) had synergistic effects on α-glucosidase inhibition according to combination index (CI)-isobologram equation. Collectively, these results showed that a combination of glyceollin and luteolin has the potential to inhibit α-glucosidase activity via a synergistic mode of action.

A probabilistic description is essential for understanding the dynamics of stochastic systems far from equilibrium. To compare different Probability Density Functions (PDFs), it is extremely useful to quantify the difference among different PDFs by assigning an appropriate metric to probability such that the distance increases with the difference between the two PDFs. This metric structure then provides a key link between stochastic processes and geometry. For a non-equilibrium process, we define an infinitesimal distance at any time by comparing two PDFs at times infinitesimally apart and sum these distances in time. The total distance along the trajectory of the system quantifies the total number of different states that the system undergoes in time and is called the information length. By using this concept, we investigate classical and quantum systems and demonstrate the utility of the information length as a unique Lagrangian diagnostic to quantify the information change as a system continuously evolves in time and to map out attractor structure. We further elucidate quantum effects (uncertainty relation) and the dual role of the width of PDF in quantum systems.

In Korea, the underground silo structure for low- and intermediate-level radioactive waste disposal facilities has been constructed and operated since 2014. Large-scale earthquakes occurred in 2016 and 2017, respectively, in Gyeongju and Pohang areas near the underground silo structures, and interest in the stability of the underground silo increased significantly. In this paper, one-dimensional free field analyses have been carried out before the three-dimensional silo dynamic analyses subjected to earthquake loadings. As an additional study, a new form of finite element equilibrium equation is derived in terms of relative motions, which is essentially the same equation as that expressed in terms of total motions where the base shear force is applied for earthquake load. The accuracy of conventional finite element solutions is evaluated by directly comparing them with closed-form solutions by frequency domain analysis such as SHAKE91.

Acoustic emission (AE) is caused by the sudden release of energy by a material as a result of material degradation related to deformation, crack, or fault within a solid. The same situation also occurs in leaks caused by turbulence in the fluid around the leak. In this study, analytical modeling for AE due to leakage through a circular pinhole in a gas storage cylinder was performed. The displacement fields responsible for AE, excited by the concentrated force (CF) associated with the turbulent flow though the pinhole, were derived by solving the Navier-Lamé equation. The CF as an excitation source was formulated in terms of a fluctuating Reynolds stress (FRS) and spatial Green’s function. In particular, a series of experiments were conducted under different operating conditions to explore the characteristics of the AE signals due to leak in a gas cylinder. Finally, the simulation and experimental results were compared to verify the accuracy of the simulation results.

This study examines the negative impacts of dark stores on the urban environment from three perspectives: land use, transportation, and streetscape. It is conducted on B-Mart, a representative dark store in South Korea. First, in terms of land use, we find that dark stores that function as logistics facilities conflict with the surrounding land use. Second, by analyzing the location of dark stores and the hourly traffic volume of delivery vehicles, we find that the impact on the surrounding transportation infrastructure and pedestrian traffic is not as significant as previously claimed. However, during the transportation and loading process of the dark store, several problems such as traffic violations, illegal parking, and illegal loading were observed, posing a risk to nearby vehicles and pedestrians. Third, in terms of streetscapes, the location of dark stores on the ground floor of buildings can harm streetscapes. The current urban planning system in South Korea does not clearly define the status and function of dark stores, making it unclear how to manage them. Therefore, it is necessary to clarify their legal definition and introduce urban planning and design guidelines that are consistent with their appropriate location and appearance.

Microbial production is a promising method that can overcome major limitations in conventional methods of lycopene production, such as low yields and variations in product quality. Significant efforts have been made to improve lycopene production by engineering either the 2-C-methyl-D-erythritol 4-phosphate (MEP) pathway or mevalonate (MVA) pathway in microorganisms. To further improve lycopene production, it is critical to utilize metabolic enzymes with high specific activities. Two enzymes, 1-deoxy-D-xylulose-5-phosphate synthase (Dxs) and farnesyl diphosphate synthase (IspA), are required in lycopene production using MEP pathway. Here, we evaluated the activities of Dxs and IspA of Vibrio sp. dhg, a newly isolated and fast-growing microorganism. Considering that the MEP pathway is closely related to the cell membrane and electron transport chain, the activities of the two enzymes of Vibrio sp. dhg were expected to be higher than the enzymes of E. coli. We found that Dxs and IspA in Vibrio sp. dhg exhibited 1.08-fold and 1.38-fold higher catalytic efficiencies, respectively. Consequently, the heterologous overexpression improved the specific lycopene production by 1.88-fold. Our findings could be widely utilized to enhance production of lycopene and other carotenoids.

The present study was conducted to evaluate encapsulated essential oils as an alternative anticoccidial in coccidiosis vaccine challenged broiler chickens. A total of 600 day-old male broiler chicks were provided with no-added corn-soybean meal-based control diet or diets that contained either salinomycin or EO at 60 and 120 mg per kg of diet. On day 21, half of the control groups were orally challenged with a coccidiosis vaccine at 25 times higher than the recommended vaccine dose. During 22 to 28 days (i.e., one-week post coccidiosis vaccine challenge), the challenged chickens had decrease (P < 0.05) in body weight gain and feed intake but increase in feed conversion ratio compared with the non-challenged, naïve control chickens. However, dietary EO significantly counteracted (P < 0.05) coccidiosis vaccine-induced depression in body weight gain and feed intake. Increasing dietary EO linearly decreased (P < 0.05) the concentrations of the volatile fatty acids. Dietary SAL and EO affected gut morphology in chickens at 20 days posthatch. Increasing dietary EO linearly (P = 0.073) increased serum catalase activity. Collectively, our study shows that dietary EO increased coccidiosis vaccine-induced growth depression and altered gut physiology in broiler chickens.

The construction of reinforced concrete (RC) structures inevitably consumes an excessive number of rebars, leading to significant cutting waste and carbon emissions. Extensive research has been conducted to minimize this issue and its consequences; however, these methods consistently consume a substantial number of rebars. This includes a previous study that utilizes the lap splice position optimization and special-length rebar concept without considering the lapping zone regulation. Moreover, conventional lap splices pose inherent drawbacks that could jeopardize the structural integrity of RC members. In contrast, mechanical couplers eliminate the need for rebar lapping, effectively reducing rebar consumption. This research aims to evaluate the impact of an integrated mechanical coupler and special-length-priority minimization algorithm on the reduction in rebar consumption and cutting waste in RC columns, achieving near-zero cutting waste. To validate the effectiveness of the proposed algorithm, it was applied to the column rebars of an RC building. The results revealed a significant reduction in ordered rebar consumption by 18.25%, accompanied by substantial reductions in cutting waste (8.93%), carbon emissions (12.99%), and total costs (10.81%) compared with a previous study. The outcomes provide the industry with insights into further reducing rebar consumption and its related consequences. Applying the proposed algorithm to various construction projects will further amplify the corresponding benefits.

This study aims to investigate the effects of chest mobilization and breathing exercises on respiratory function, trunk stability, and endurance in chronic stroke patients who have contracted coronavirus disease (COVID-19). Thirty inpatients of a tertiary hospital in South Korea, who had a history of COVID-19 and were diagnosed with stroke within the last 6 months were randomly assigned to either the Chest Mobilization Exercise with Breathing Exercise (CMEBE) or Conservative Physical Therapy with Breathing Exercise (CPTBE) groups. The respiratory function, trunk stability, and endurance were measured at baseline and 6 weeks after the interventions. Both CMEBE and CPTBE groups showed improvements in respiratory function, trunk stability, and endurance after the intervention (p<0.05). However, the CMEBE group showed significantly greater improvements in forced expiratory volume in 1 second (p<0.05), trunk stability (p<0.05), and endurance (p<0.05) than the CPTBE group. No significant intergroup difference was observed in forced vital capacity and peak expiratory flow. Conclusion: The combination of chest mobilization and breathing exercises improved respiratory muscle mobility and endurance, stabilized the trunk, and enhanced balance and transfer of weight. The findings suggest that this intervention could be beneficial in improving respiratory function and endurance in stroke patients.

We investigated the characteristics of surface wind speeds and temperatures predicted by the local data assimilation and prediction system (LDAPS) operated by the Korean Meteorological Administration. First, we classified automated weather stations (AWSs) into four categories [urban flat (Uf), rural flat (Rf), rural mountainous (Rm), and rural coastal (Rc) terrains] based on the surrounding land cover and topography, and selected 25 AWSs representing each category. Then we calculated the mean bias error of wind speed (WE) and temperature (TE) using AWS observations and LDAPS predictions for the 25 AWSs in each category for a period of 1 year (January–December 2015). We found that LDAPS overestimated wind speed (average WE = 1.26 m s–1) and underestimated temperature (average TE = –0.63°C) at Uf AWSs located on flat terrain in urban areas because it failed to reflect the drag and local heating caused by buildings. At Rf, located on flat terrain in rural areas, LDAPS showed the best performance in predicting surface wind speed and temperature (average WE = 0.42 m s–1, average TE = 0.12°C). In mountainous rural terrain (Rm), WE and TE were strongly correlated with differences between LDAPS and actual altitude. LDAPS underestimated (overestimated) wind speed (temperature) for LDAPS altitudes that were lower than actual altitude, and vice versa. In rural coastal terrain (Rc), LDAPS temperature predictions depended on whether the grid was on land or sea, whereas wind speed did not depend on grid location. LDAPS underestimated temperature at grid points on the sea, with smaller TE obtained for grid points on sea than on land.

Cardiovascular disease is the leading cause of death worldwide. A key factor in assessing the risk of cardiovascular disease is left ventricular functional evaluation. Left ventricular (LV) systolic function is evaluated by measuring the left ventricular ejection fraction (LVEF) using echocardiography data. Therefore, quick and accurate left ventricle segmentation is important for estimating the LVEF. However, it is difficult to accurately segment the left ventricle due to changes in the shape and area of the left ventricle during cardiac cycles. In this study, we proposed a framework that considers changes in the shape and area of the left ventricle during the cardiac cycle by applying the convolutional long short-term memory (CLSTM) approach. In addition, we evaluated the left ventricular segmentation and multidimensional quantification of the proposed system in comparison to manual and automated segmentation methods. In addition, to assess the validity of CLSTM, the values of multi-dimensional quantification metrics were compared and analyzed using graphs and Bland–Altman plots on a frame-by-frame basis. We demonstrated that the CLSTM method effectively segments the left ventricle by considering the LV activity. In conclusion, we demonstrated that LV segmentation based on our framework may be utilized to accurately estimate LVEF values.

TGF-ꞵ signaling is a vital regulator for maintaining articular cartilage homeostasis. Runx transcription factors, downstream targets of TGF-ꞵ signaling, have been studied in the context of osteoarthritis (OA). Although Runx partner core binding factor β (Cbfβ) is known to play a pivotal role in chondrocyte and osteoblast differentiation, the role of Cbfβ in maintaining articular cartilage remains obscure. This study investigated Cbfβ as a novel anabolic modulator of TGF-ꞵsignaling and determined its role in articular cartilage homeostasis. Cbfβ significantly decreased in aged mouse articular cartilage and human OA cartilage. Articular chondrocyte-specific Cbfb-deficient mice (Cbfb△ac/△ac) exhibited early cartilage degeneration at 20 weeks old and developed OA at 12 months old. Cbfb△ac/△ac mice showed enhanced OA progression under the surgical-induced mice OA model. Mechanistically, forced expression of Cbfβ rescued Col2α1 and Runx1 expression in Cbfβ-deficient chondrocytes. TGF-ꞵ1-mediated Col2α1 expression failed despite the pSmad3 activation under TGF-ꞵ1 treatment in Cbfβ-deficient chondrocytes. Cbfβ protected Runx1 from proteasomal degradation through Cbfβ/Runx1 complex formation. These results indicate that Cbfβ is a novel anabolic regulator for cartilage homeostasis, suggesting that Cbfβ could protect OA development by maintaining the integrity of the TGF-ꞵ1 signaling pathway in articular cartilage.

Titanium dioxide nanoparticles (TiO2NPs) are used in products that are applied to the human body, such as cosmetics and food, but their biocompatibility remains controversial. Pycnogenol (PYC), a natural extract of pine bark, exerts anti-inflammatory and antioxidant effects. In this study, we investigated whether PYC effectively alleviates pulmonary toxicity induced by airway exposure to TiO2NPs, and the beneficial effects of PYC were explained through the analysis of changes to the mechanism of cytotoxicity. TiO2NPs induced pulmonary inflammation and mucus production, increased the levels of malondialdehyde, and upregulated thioredoxin-interacting protein (TXNIP) and cleaved-caspase 3 (Cas3) in the lungs of mice. However, PYC treatment reduced the levels of all toxicity markers of TiO2NPs and restored glutathione levels. These antioxidant and anti-inflammatory effects of PYC were also demonstrated in TiO2NP-exposed human airway epithelial cells by increasing the mRNA levels of antioxidant enzymes and decreasing the expression of TXNIP, cleaved-Cas3, and inflammatory mediators. Taken together, our results showed that PYC attenuated TiO2NP-induced lung injury via TXNIP downregulation. Therefore, our results suggest the potential of PYC as an effective anti-inflammatory and antioxidant agent against TiO2NP-induced pulmonary toxicity.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

Amid the deepening imbalance in the supply and demand of allogeneic organs, xenotransplanta-tion can be a practical alternative because it makes an unlimited supply of organs possible. How-ever, to perform xenotransplantation on patients, the source animals to be used must be free from infectious agents. This requires breeding of animals using assisted reproductive techniques, such as somatic cell nuclear transfer, embryo transfer, and cesarean-section, without colostrum de-rived in designated pathogen-free (DPF) facilities. Most infectious agents can be removed from animals produced by these methods, but several viruses known to pass through the placenta are not easy to remove, even with these methods. Therefore, in this review, we look at the characteris-tics of several viruses known to cross the placenta and determine how they can be detected. This review is intended to help maintain DPF facilities by preventing animals infected with the virus from entering DPF facilities and to help select pigs suitable for xenotransplantation.

In this study, various diamine monomers were used to synthesize aramid polymer films via a low-temperature solution condensation reaction with diacid chloride. For diamines with relatively high basicity, the reaction system became opaque because amine salt formation inhibited polymer synthesis. Meanwhile, low-basicity diamines with strong electron-withdrawing groups, such as CF3 and sulfone, were smoothly polymerized without amine salt formation to provide highly viscous solutions. The acid byproduct HCl generated during polymerization was removed by adding propylene oxide to the reaction vessel and converting the acid into highly volatile inert substances. The resulting solutions were used as varnishes without any additional purification, and polymer films with an excellent appearance were easily obtained through a conventional casting and convection drying process. The films neither tore nor broke when pulled or bent by hand; furthermore, even when heated up to 400°C, they did not decompose or melt. Moreover, polymers prepared from 2,2-bis (trifluoromethyl) benzidine (TFMB) and bis (4-aminophenyl) sulfone (pAPS) did not exhibit glass transition until decomposition. The prepared polymer films showed a high elastic modulus of more than 4.1 GPa and a high tensile strength of more than 52 MPa. In particular, TFMB-, pAPS-, and 2,2-bis (4-aminophenyl) hexafluoropropane-based polymer films were colorless and transparent, with very high light transmittances of 95%, 96%, and 91%, respectively, at 420 nm and low yellow indexes of 2.4, 1.9, and 4.3, respectively.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

The frame construction of an apartment complex that consists of multiple buildings encounters various uncertainties, owing to the complex relationships among units of work. Currently, the period of such a construction is calculated based on the number of floors of the highest building in the complex. This study quantitatively analyzes an apartment frame construction period using a queue model and evaluates the validity of the estimated period. In this regard, a methodology is proposed for analyzing the construction period by applying the concept of a customer and a server. A case study on the duration of an apartment frame construction is conducted with Korea Land and Housing Corporation, which has supplied the largest number of apartments in South Korea. It was found that the stable state of a queue system was observed when the rate of server utilization was applied to the basement and aboveground floors. However, a stable state was not reached on the ground floor. This study includes non-working days in its calculation and quantitatively analyzes uncertainty factors during construction. Therefore, the findings can be practically utilized to quantitatively plan the durations of work units in an apartment frame construction.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

Interstitial lung disease (ILD) is one of the most serious extra-articular complications of rheu-matoid arthritis (RA), which increases the mortality of RA. Because the pathogenesis of RA-ILD remains poorly understood, appropriate therapeutic strategies and biomarkers have not yet been identified. Thus, the goal of this review was to summarize and analyze the reported data on the etiology and pathogenesis of RA-ILD. The incidence of RA-ILD increases with age, and is also generally higher in men than in women and in patients with specific genetic variations and eth-nicity. Lifestyle factors associated with an increased risk of RA-ILD include smoking and exposure to pollutants. The presence of an anti-cyclic citrullinated peptide antibody, high RA disease activity, and rheumatoid factor positivity also increase the risk of RA-ILD. We also explored the roles of biological processes (e.g., fibroblast–myofibroblast transition, epithelial–mesenchymal transition, and immunological processes), signaling pathways (e.g., JAK/STAT and PI3K/Akt), and the his-topathology of RA involved in RA-ILD pathogenesis based on published preclinical and clinical models of RA-ILD in animal and human studies.

This study investigated the effects of whole-body circuit training using a weighted vest on plasma resistin, cardiovascular disease risk factors, and cardiorespiratory fitness for normal-weight obese women. In this study, thirty- six normal-weight obese women were divided into three groups: Weighted Vest Circuit Training (WVCT) (n = 12), Body Weight Circuit Training (BWCT) (n = 12), and Control (CON) (n = 12). Whole-body circuit training was conducted three times a week for eight weeks to compare and analyze plasma resistin, cardiovascular disease risk factors, and cardiorespiratory fitness before and after training. Although there was no significant baseline difference between the groups regarding skeletal muscle mass, it significantly increased for the WVCT group after eight weeks. percent body fat significantly decreased for the WVCT and BWCT groups, and there was a significant difference when the percent body fat of these two groups were compared to that of the control group. Moreover, the WVCT and BWCT groups displayed a significant decrease in plasma resistin, showing a significant difference from the CON group. The WVCT and BWCT group showed a significant decrease in plasma IL-6, whereas the CON group showed a significant increase. VO2max significantly increased post-training compared to before in the BWCT group and the WVCT group, and the WVCT group showed differences between groups compared to the BWCT group and the CON group. None of the three groups displayed significant changes in plasma hs-CRP, yet there was a significant difference between the hs-CRPs of the WVCT and BWCT group and that of the CON group. In conclusion, whole-body circuit training using a weighted vest efficiently improves body composition, plasma resistin, and cardiopulmonary fitness, reducing cardiovascular disease risk factors in normal-weight obese women.

According to statistics from the Food and Agriculture Organization, the world population will increase to about 91 million (Asia 51 million, Africa 19 million). A rise in the world’s population means an increased need for food. However, climate change has caused desertification and unpredictable weather, creating problems in the supply and demand of food. Sweet potato (Ipomoea batatas) is an alternative to solving the food problem, as it is one of the world’s most important food crops, especially in developing countries. The tuberous roots of sweet potato are usually used as staple food, animal feed, industrial material, or raw material for alcohol production. In the future, more variations of sweet potato will be needed for breeding this crop. Recently, molecular markers developed for sweet potato have demonstrated good potential for use in genetic selection. In this study, a cDNA library was constructed from the total RNA of sweet potato leaves. A total of 789 copies of the cDNA were cloned in Escherichia coli by employing the pGEM-T Easy vector. Sequencing was carried out by Solgent Co. (Korea). As many as 579 expressed sequence tag–simple sequence repeat (EST-SSR) markers were designed (73.38%) from the known cDNA nucleotide base sequences. The lengths of the developed EST-SSR markers ranged from 100 to 499 bp (average length 238 bp). Their motif sequence types were varied, with most being dinucleotides and pentanucleotides, and the most commonly found motifs were CAGAAT (29.0%) and TCT (2.8%). Based on these SSR-containing sequences, 619 pairs of high-quality SSR primers were designed using WebSat and Primer3web. The total number of primers designed was 144. Polymorphism was evident in 82 EST-SSR markers among 20 Korean sweet potato cultivars tested and in 90 EST-SSR markers in the two parents of a mapping population, Yeseumi and Annobeny. In this study, the hexaploid sweet potato (2n = 6x = 90) EST-SSR markers were developed in the absence of full-sequence data. Moreover, by acting as a molecular tag for particular traits, the EST-SSR marker can also simultaneously identify information about the corresponding gene. These EST-SSR markers will allow the molecular analysis of sweet potato to be done more efficiently. Thus, we can develop high-quality sweet potato while overcoming the challenges from climate change and other unfavorable conditions.

In order to understand the effect of Pb-CuI co-doping on the thermoelectric performance of Bi₂Te₃, n-type Bi₂Te₃ co-doped with x at% CuI and 1/2x at% Pb (x = 0, 0.01, 0.03, 0.05, 0.07, and 0.10) were prepared via high temperature solid state reaction and consolidated using spark plasma sintering. Electron and thermal transport properties, i.e., electrical conductivity, carrier concentration, Hall mobility, Seebeck coefficient, and thermal conductivity, of CuI-Pb co-doped Bi₂Te₃ were measured in the temperature range from 300 K to 523 K and compared to corresponding x% of CuI-doped Bi₂Te₃ and undoped Bi₂Te₃. The addition of a small amount of Pb significantly decreased the carrier concentration, which could be attributed to the holes from Pb atoms, thus the CuI-Pb co-doped samples show a lower electrical conductivity and a higher Seebeck coefficient compared to CuI-doped samples with similar x values. The incorporation of Pb into CuI-doped Bi₂Te₃ rarely changed the power factor because of the trade-off relationship between the electrical conductivity and the Seebeck coefficient. The total thermal conductivity(κ_tot) of co-doped samples (κ_tot ~1.4 W/m∙K at 300 K) is slightly lower than that of 1% CuI-doped Bi₂Te₃ (κ_tot~1.5 W/m∙K at 300 K) and undoped Bi₂Te₃ (κ_tot ~1.6 W/m∙K at 300 K) due to the alloy scattering. The 1% CuI-Pb co-doped Bi₂Te₃ sample shows the highest ZT value of 0.96 at 370 K. All data on electrical and thermal transport properties suggest that the thermoelectric properties of Bi₂Te₃ and its operating temperature can be controlled by co-doping.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

The number of patients with bone metabolic disorders including osteoporosis is increasing worldwide. These disorders often facilitate bone fractures, which seriously impact the patient’s quality of life and could lead to further health complications. Bone homeostasis is tightly regulated to balance bone resorption and formation. However, many anti-osteoporotic agents are broadly categorized as either bone forming or anti-resorptive, and their therapeutic use is often limited due to unwanted side effects. Therefore, safe and effective therapeutic agents are needed for osteoporosis. This study aims to clarify the bone protecting effects of oat bran water extract (OBWE) and its mode of action. OBWE inhibited RANKL-induced osteoclast differentiation by blocking c-Fos/NFATc1 through the alteration of I-κB. Furthermore, we found that OBWE enhanced BMP-2-stimulated osteoblast differentiation by the induction of Runx2 via Smad signaling molecules. In addition, the anti-osteoporotic activity of OBWE was also evaluated using an in vivo model. OBWE significantly restored ovariectomy-induced bone loss. These in vitro and in vivo results showed that OBWE has the potential to combat bone metabolic disorders including osteoporosis

Organizing pneumonia (OP) can be diagnosed pathologically, and cryptogenic OP (COP) and secondary OP (SOP) have been classified by cause and underlying context. Because it is clinically difficult to differentiate between COP and SOP, this study investigated characteristics that could distinguish between COP and SOP. The medical records of patients who underwent lung biopsy from 2016 to 2018 were retrospectively reviewed. Eighty-five patients had pathologically proven OP, including 16 diagnosed with COP and 69 diagnosed with SOP. The most common cause of SOP was infectious pneumonia, observed in 57 (82.6%) of the 69 patients. Median time from symptom onset to hospital admission is shorter (P=0.006) and fever was more common (P=0.021) in the SOP. Some laboratory results differed significantly between the two groups. Lymphocyte in bronchoalveolar lavage fluid were higher in the COP (P=0.012). Radiologic findings showed that effusion was more common in the SOP (P=0.043). There were no between-group differences in steroid use, 30 day and in-hospital mortality rates, and rates of OP outcomes and recurrences. Infection is the main cause of SOP. Symptom onset is more rapid in patients with SOP. Pleural effusion was more common in the SOP but there were no differences in clinical course.

The protein extract of Ulva australis hydrolyzed with alcalase and flavourzyme investigated multi-functional properties, including total antioxidant capacity (TAC), collagenase inhibitory and antibacterial activities. The #5 fraction (SP5) and #7 fraction (SP7) of U. australis hydrolysate from cation-exchange chromatography showed significantly high TAC, collagenase inhibitory and antibacterial effects against Propionibacterium acnes, and only Q3 fraction from anion-exchange chromatography showed high multi-functional activities. The eight peptides among 42 peptides identified by MALDI-TOF/MS and Q-TOF/MS/MS were selected from the results to screen molecular docking on target proteins, and were synthesized. Thr-Gly-Thr-Trp (TGTW) showed ABTS [2,2′-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid)] radical scavenging activity. Effect TAC as Trolox equivalence was dependent on the concentration of TGTW. The Asn-Arg-Asp-Tyr (NRDY) and Arg-Asp-Arg-Phe (RDRF) possessing collagenase inhibitory activity increased according to the increase of concentration and the IC50 values of them were 0.95 mM and 0.84 mM, respectively. Peptides, RDRF and His-Ala-Val-Tyr (HAVY) showed anti-P. acnes effects with IC50 values of 8.57 mM and 13.23 mM, respectively. These results suggest that the U. australis hydrolysate could be a resource for the application of effective nutraceuticals and cosmetics.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

Acetic acid bacteria (AAB) are major contributors to the production of fermented vinegar, offering various cultural, culinary, and health benefits. Although the residual unpasteurized AAB after vinegar production are not pathogens, these are necessary the safety evaluations including antibiotic resistance for the use as starters. In this research, we investigated the antibiotics resistance profiles of 26 AAB strains, including various species of Komagataeibacter and Acetobacter, against ten different antibiotics using the E-test method. All strains exhibited resistance to aztreonam and clindamycin. Komagataeibacter species demonstrated a 50% resistance rate to ciprofloxacin, analogous to Acetobacter species, but showed twice the resistance rates to chloramphenicol and erythromycin. Genomic analysis of K. saccharivorans CV1 identified intrinsic resistance mechanisms, such as multidrug efflux pumps, thereby enhancing our understanding of antibiotic resistance in acetic acid-producing bacteria. These findings enhance understanding of antibiotic resistance in AAB for food safety and new antimicrobial strategies, suggesting the need for standardized testing methods and molecular genetic study.

Phototherapy is an efficient strategy to respond to oxidative stress and has been in the spotlight in various therapeutic fields through its biological effect, but the exact molecular mechanism has not yet been established. As a result of irradiating RAW264.7 cells with a 630 nm or 850 nm LED with an energy intensity of 0.01J/cm2, cell viability was increased depend on the irradiation time. After H2O2 was added, 630 nm or 850 nm LEDs were irradiated for 10 min or 40 min to increase cell viability by about 1.7- or 1.6-fold, respectively. In addition, 630nm or 850nm LED irradiation showed a significant ROS scavenging effect and significantly reduced TUNEL-positive cells by 45.7% and 37.8%, respectively, compared to cells treated only with H2O2. In the result of flow cytometry, the number of cells in the late apoptosis stage was about 2.3- and 1.8-fold lower than that of the cells treated with H2O2 only, but there was no significance. The Bax/Bcl-2 ratio of cells irradiated with 630 nm or 850 nm LED was significantly lower than that of cells treated with H2O2 only, and the expression of procaspase-3 and cleaved PARP was also significantly expressed in the direction of suppressing cell death. In conclusion, the ROS scavenging activity by 630 nm or 850 nm LED irradiation, leading the expression of cell death pathway proteins in the direction of inhibiting cell death.

To protect skin from harmful ultraviolet (UV), zinc oxide (ZnO) with tannin from gallnuts was treated on cotton and polyester fabrics in this study. Before the treatments, the fabrics were dyed with shikonin and xanthophyll from Gromwell and Cape Jasmine. First, this study found that xanthophyll was more effective at preventing light fade or discoloration than shikonin. Despite the highest K/S, the untreated cotton in violet faded the most intensely when exposed to UV. The color variation of untreated polyester was narrow, with little change in L, a*, and K/S. Due to the non-photochemical xanthophyll, the yellow-dyed samples treated with ZnO/polyphenol did not vary yellowness (b*: 28.838) significantly, while the violet fabrics displayed a significant decrease in K/S and an increase in b*. The combination of ZnO and polyphenol treatment improved UV absorption at 350 to 250 nm. Cu-mordanting after ZnO/polyphenols treatment caused the violet cotton to turn reddish from blueish (negative to positive b*), with a hue change of 316° to 59° and the highest ΔE (25.90±4.34) after UV exposure. In this study, the combination of ZnO/polyphenol with Cu-mordants contributed the xanthophyll-dyed polyester to achieve a minimum ΔE and keep chroma and hue after UV exposure.

Goal-conditioned reinforcement learning (RL) holds promise for addressing intricate control challenges by enabling agents to learn and execute desired skills through separate decision modules. However, the irregular occurrence of required skills poses a significant challenge to effective learning. In this paper, we demonstrate the detrimental effects of this imbalanced skill(sub-goal) distribution and propose a novel training approach, Classified Experience Replay (CER), designed to mitigate this challenge. We demonstrate that adapting our method to conventional RL methods significantly enhances the performance of the RL agent. Considering the challenges inherent in tasks such as driving, characterized by biased occurrences of required sub-goals, our study demonstrates the improvement in trained outcomes facilitated by the proposed method. In addition, we introduce a specialized framework tailored for self-driving tasks on highways, integrating Model Predictive Control (MPC) into our RL trajectory optimization training paradigm. Our approach, utilizing CER with the suggested framework, yields remarkable advancements in trajectory optimization for RL agents operating in highway environments.

Precision metagenomic approaches using Oxford Nanopore Technology (ONT) sequencing has been shown to allow recovery of complete genomes of Escherichia coli O157:H7 from overnight enrichments of agricultural waters. This study tests the applicability of a similar approach for Cronobacter genome recovery from powdered infant formula (PIF) overnight enrichments, where Cronobacter typically dominates the overall microbiome (&gt;90%). In this study, we aimed to test whether using ONT sequencing of overnight PIF enrichments could recover a completely closed Cronobacter genome for further genomic characterization. Ten PIF samples, each inoculated with different Cronobacter strains, covering Cronobacter sakazakii, C. muytjensii, C. dublinensis, C. turicensis, and C. universalis, were processed according to the Bacteriological Analytical Manual (BAM) protocol. qPCR was used for initial screening (detection and quantification) of the overnight enrichments and confirmed that the spiked PIF samples after the overnight enrichment have high levels of Cronobacter (107 to 109 CFU/mL). DNA from overnight PIF enrichments was extracted from the enrichment broth and sequenced using ONT. Results showed that ONT sequencing could accurately identify, characterize, and close the genomes of Cronobacter strains from overnight PIF enrichments in 3 days, much faster than the nearly two weeks required by the current BAM method. Complete genome recovery and species differentiation were achieved. This suggests that combining qPCR with ONT sequencing provides a rapid, cost-effective alternative for detecting and characterizing Cronobacter in PIF, enabling timely corrective actions during outbreaks.

This study aimed to investigate the influence of urban garden activities on participants' Perceived restorativeness, resilience, sense of community, and stress reduction. Ninety individuals who agreed to participate to the experiment were divided into experimental and control groups. To collect data 16 sessions of urban garden activities were conducted every two weeks from May to November of 2022. Perceived Restorativeness Scale, Conner-Davidson Resilience Scale, Sense of Community Index, and Brief Encounter Psychosocial Instrument were employed to measure participants’ psychological effects. To evaluate physiological effect salivary cortisol tests were performed. The results of the study revealed that urban gardening activities influenced on participants' physiological and psychological reactions in positive ways.

The purpose of this study is to analyze the causes of cost variation in natural disaster prevention projects (NDPP) in Gyeongsangbuk-do and to develop effective cost and risk management strategies. The study collected data by conducting an online survey of 244 stakeholders. Binary logistic regression was used to analyze the impact of various variables on cost deviation, in-cluding project management risk (PMR), project costing and execution risk (PCER), project exe-cution strategy risk (PESR), construction project risk (CPR), project cost and schedule risk (PCSR), project management challenges (PMC), and construction project subcontractor and safety man-agement (CPSSM). The results showed that PMR (OR=3.744, 95% C.I. [1.657, 8.457]), PCER (OR=5.068, 95% C.I. [2.236, 11.484]), PESR (OR=3.447, 95% C.I. [1. 853, 6.413]), CPR (OR=2.292, 95% C.I. [1.020, 5.151]), PCSR (OR=4.817, 95% C.I. [2.250, 10.317]), PMC (OR=2.954, 95% C.I. [1.452, 6. 013]), and CPSSM (OR=2.419, 95% C.I. [1.297, 4.515]) had statistically significant effects on cost deviation. In particular, PMR, PCER, and PESR were identified as the main causes, and the effects of additional factors such as CPSSM were also important. The developed predictive model plays an important role in helping stakeholders of NDPP to manage risks in advance and take appro-priate preventive measures to ensure the success of the project. This study empirically supports the theoretical hypotheses of previous studies and provides a clear understanding of the causes of cost deviation in NDPP, which provides important insights for strategic decision-making and provides a new perspective on risk management.

The reaction mechanism of the carboxylation of K-2-naphthoxide was investigated by density functional theory calculations and spectroscopic studies. The reaction intermediates and products were confirmed by CO₂ adsorbed-FTIR and ¹H-NMR measurements. Four steps of the reaction pathway were identified: CO₂ activation, electrophilic substitution, CO₂-K complex rearrangement, and H-shift, producing 2-hydroxy-1-naphthoic acid (2,1-HNA), 2-hydroxy-3-naphthoic acid (2,3-HNA), and 2-hydroxy-6-naphthoic acid (2,6-HNA). The occurrence of CO₂-K complex rearrangement was also confirmed. These energy profiles of reaction pathways for the reaction intermediates were well consistent the experimental results on the carboxylation of K-2-naphthoxide.

This study aimed to investigate the characteristics of composite scaffolds in combination of fibroin and carboxymethyl cellulose (CMC) in bone tissue engineering. Fibroin is a useful biomaterial and is a major component of silk yarns composed of fibrous proteins. Improving for binding efficiency in bone formation after implanted scaffold, CMC was added to fibroin. CMC could improve injectable characters in bone substitutes by adding in scaffold material, fibroin. The porous shapes, porosity, surface wettability, water absorption, and thermal properties of the CMC added fibroin scaffold were better than fibroin only scaffold. For tissue engineering of bone marrow mesenchymal stem cells (BMSCs), BMSCs isolated from mice were seeded onto the scaffold, and the cell proliferation rate was measured. alkaline phosphatase activity in BMSCs was higher in the scaffold containing CMC than that in the scaffold containing fibroin alone. The expression levels of osteocyte marker genes and proteins were increased in the CMC scaffold. The biocompatibility and hydrophilicity of CMC scaffolds play important roles in the growth and proliferation of osteocytes. Furthermore, the CMC scaffold design proposed in this study could play an important role in facilitating cartilage, ossification, and nerve differentiation of BMSCs.

We report the use of four-layer graphene (4LG) as a highly reliable transparent conductive electrode (TCE) for polymer-dispersed liquid crystal (PDLC)-based smart window devices. The adhesion between 4LG and the substrate was successfully improved through a water-induced interface-cleaning (WIIC) process. We compared the performance of a device with a WIIC-processed 4LG electrode with that of devices with a conventional Indium tin oxide (ITO) electrode and a 4LG electrode without a WIIC. With the application of the WIIC process, the PDLC smart window with a 4LG electrode exhibited reduced turn-on voltage and haze compared to 4LG without the WIIC process and characteristics comparable to those of the ITO electrode. Based on our observations, we conclude that 4LG with WIIC is a promising TCE for flexible smart windows.

A probabilistic description is essential for understanding the dynamics of stochastic systems far from equilibrium, given uncertainty inherent in the systems. To compare different Probability Density Functions (PDFs), it is extremely useful to quantify the difference among different PDFs by assigning an appropriate metric to probability such that the distance increases with the difference between the two PDFs. This metric structure then provides a key link between stochastic systems and information geometry. For a non-equilibrium process, we define an infinitesimal distance at any time by comparing two PDFs at times infinitesimally apart and sum these distances in time. The total distance along the trajectory of the system quantifies the total number of different states that the system undergoes in time, and is called the information length. By using this concept, we investigate the information geometry of non-equilibrium processes involved in disorder-order transitions between the critical and subcritical states in a bistable system. Specifically, we compute time-dependent PDFs, information length, the rate of change in information length, entropy change and Fisher information in disorder-to-order and order-to-disorder transitions, and discuss similarities and disparities between the two transitions. In particular, we show that the total information length in order-to-disorder transition is much larger than that in disorder-to-order transition, and elucidate the link to the drastically different evolution of entropy in both transitions. We also provide the comparison of the results with those in the case of the transition between the subcritical and supercritical states and discuss implications for fitness.

The economic development and infrastructure of a nation are closely interrelated. In addition, public trust in national infrastructure facilities is closely linked to the preservation of the advantages provided by these facilities to the public. Since the 1970s, Korea has achieved exponential economic growth over a short period of time and the number of infrastructure facilities has increased correspondingly. This compressed economic development has been underpinned by the national infrastructure, whose safety and usability have been excluded from the scope of the development. However, after around 30 years, structural deterioration coupled with general insensitivity to safety in today’s society has considerably reduced public trust in using the infrastructure. Realistically, policies that mainly focus on developing new technologies related to infrastructure construction have led to practical limitations that discourage the development of technologies for maintenance or inspection. Furthermore, current maintenance works face certain limitations caused by various reasons: insufficient budget, increasing number of infrastructure facilities requiring maintenance, shortage of manpower, and rapidly increasing number of aging infrastructure facilities. To overcome these limitations, a new approach is required that is different from general inspection methods under the existing rules and regulations. In this context, this study aimed to explore the efficiency of bridge inspection and maintenance by unmanned aerial vehicles (UAVs) that could observe inaccessible areas, could be conveniently and easily controlled, and could offer high economic benefits. To this end, various tests were performed on elevated bridges, and suitable UAV images were obtained. The obtained UAV images were inspected by using machine vision technology, thereby excluding subjective evaluations by humans. Methods for enhancing the objectivity of the inspection were also discussed. The test results showed that both the efficiency and objectivity of the proposed method were better than those of the existing bridge maintenance and inspection methods.

Plant-derived compounds have been historically used for the treatment of various diseases and an important source of several clinically useful anti-cancer agents. The Artemisia annua is known as a medicinal herb that is effective against cancer. Thus, the purpose of this study was to investigate whether ethanol extracts of Artemisia annua could increase an anti-cancer effect against LS174T cells. Our results show that Artemisia annua extracts (AAE) induces apoptosis through the regulation of mitochondria outer membrane potential. We demonstrate that apoptosis is induced by p53-dependent manner when cells were treated with Nutlin-3 (MDM2 inhibitor) and LY294002 (Akt inhibitor). In addition, the apoptotic effect was also observed in the p53-independent manner through pifithrin-α (p53 inhibitor) and celecoxib (COX-2 inhibitor) treatment. As in in vitro, AAE induced apoptotic effects and regulated apoptosis-related proteins in LS174T xenograft model. Taken together, these results suggest that Artemisia annua extracts exerts an anti-cancer effect through p53-independent manner, as well as p53-dependent manner by p53´ translocation in LS174T colon cancer cells.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

In recent years, the AHRS has become an important research area. In order to improve the orientation measurement accuracy of AHRS, this paper first expounds the algorithm principle of the AHRS. Then, aiming at the problem of poor stability of the traditional gradient descent method under high dynamics or large magnetic field interference, a gain-scheduled anti-interference AHRS orientation algorithm is designed. By using the switching architecture designed with this algorithm for gain scheduling, it can ensure stable performance while being subjected to apparent acceleration and ferromagnetic interference. Finally, experimental verification is conducted, and the experimental results show that: in the presence of interference, the roll angle error is 0.0350°, the pitch angle error is 0.0277°, and the yaw angle error is 0.9611°, thereby verifying the strong anti-interference performance of the gain-scheduled AHRS orientation algorithm proposed in this paper.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.

The phenolics concentrations of rapeseed are important because they are antinutritional com-pound or directly positive related to antioxidant actives. In this study, single nucleotide poly-morphisms (SNPs) identified from genotyping-by-sequencing (GBS), and genome-wide associa-tion study of phenolic contents were investigated in 95 rapeseed mutant lines derived from gamma rays and their original cultivar. A total of 3,196,318 SNPs were detected, identifying a set of 70,208 union SNPs used to perform association studies. Six phenolics and glucosinolate (pro-goitrin) were identified, sinapine was the major phenolic compound (91.2–99.2%) in all geno-types. The association study was conducted for six phenolic compounds, progoitrin, total sinap-ine content (TSC), total phenolic content (TPC) and seed yield. The association study identified 241 SNPs that were significantly associated with six phenolic compounds, progoitrin, TSC and TPC. Based on the detected SNP markers, BnaA06g31740D, a gene associated progoitrin, BnaC-nng39930D, a gene associated trans-sinapine 1, BnaA07g31720D, a gene associated trans-sinapine 2, BnaC03g31950D and BnaA06g09180D, a gene associated TSC, and BnaAnng27700D, a gene associ-ated TPC, were selected as candidate genes. The SNP makers associated major phenolic com-pounds identified and could be used as targets for breeding programs aimed at improving anti-oxidant contents and reducing antinutritional components.

Large lithium-ion batteries (LIBs) in electric vehicles and energy storage systems demonstrate different performance and lifetime compared to small LIB cells, owing to the size effects generated by the electrical configuration and property imbalance. However, the calculation time for performing life predictions with three-dimensional (3D) cell models is undesirably long. In this paper, a lumped cell model with equivalent resistances (LER cell model) is proposed as a reduced order model of the 3D cell model, which enables accurate and fast life predictions of large LIBs. The developed LER cell model is validated via the comparisons with results of the 3D cell models by simulating a 20-Ah commercial pouch cell (NCM/graphite) and the experimental values. In addition, the LER cell models are applied to different cell types and sizes, such as a 20-Ah cylindrical cell and a 60-Ah pouch cell.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

The association between the choice of general anesthetic agents and the risk of acute kidney injury (AKI) and long-term renal function after nephrectomy has not yet been evaluated. We reviewed 1087 cases of partial or radical nephrectomy. The incidence of postoperative AKI, new-onset chronic kidney disease (CKD) stage 3a and CKD upstaging were compared between different general anesthetic agent groups: propofol, sevoflurane, and desflurane. Four different propensity score analyses were performed to minimize confounding for each pair of comparison (propofol vs sevoflurane; propofol vs desflurane; sevoflurane vs desflurane; propofol vs volatile agents). Study outcomes were compared before and after matching. Kaplan-Meier survival curve analysis was performed to compare renal survival determined by the development of CKD stage 3a between groups up to 36 months after nephrectomy before and after matching. Propofol was associated with a lower incidence of AKI, CKD upstaging and a higher three-year renal survival after nephrectomy compared to sevoflurane or desflurane group after matching (AKI: propofol 23.2% vs. sevoflurane 39.5%, P=0.004, vs. desflurane 34.3%, P=0.031; CKD upstaging: propofol 27.2% vs. sevoflurane 58.4%, P<0.001, vs. desflurane 48.6%, P=0.017; Log-rank test propofol vs. sevoflurane P<0.001, vs. desflurane P=0.015). Propofol was also associated with a lower incidence of new-onset CKD after nephrectomy compared to sevoflurane after matching (P<0.001). However, there were no significant differences between sevoflurane and desflurane. In conclusion, propofol, compared to volatile agents, may be the reasonable choice of general anesthetic agent for nephrectomy to attenuate postoperative renal dysfunction. Randomized prospective trials are warranted to test this hypothesis.

Suicide is a major public health concern in South Korea, and self-poisoning by pesticides is one of the common methods of suicide. Pesticide ban policies have been successful for suicide prevention; however, no studies have shown their effect according to occupational groups. The present study analyzed suicide and suicide by pesticide rates among South Korean workers age 15-64 in 2003-2017, their associations with occupational groups, and the impact of three major economic indices on these factors. Workers in the agriculture, forestry, and fishery industries have relative risks of 5.62 (95% CI: 5.54-5.69) for suicide overall and 25.49 (95% CI: 24.46-26.57) for suicide by pesticide. The real gross domestic product (RGDP) has a positive association with suicide overall only in the last five-year period investigated in this study, and the unemployment rate consistently has a positive association. The economic status and policy for suicide prevention affect suicide and suicide by pesticide rates differently among occupational groups and different time periods. Policy addressing suicidal risk for different occupational groups should be of concern in South Korea.

Coxsackievirus A6 (CV-A6) has emerged as the predominant causative agent of hand, foot, and mouth disease (HFMD) in young children. Since the declaration of coronavirus disease 2019 (COVID-19) as a global pandemic, the incidence of infectious diseases, including HFMD, has decreased markedly. When social mitigation was relaxed during the COVID-19 pandemic in 2022, re-emergence of HFMD was observed in Gwangju, South Korea, and seasonal characteristics of the disease appeared to have changed. To investigate the molecular characteristics of enterovirus (EV) associated with HFMD during 2022, 277 specimens were collected. Children aged under 5 years accounted for the majority of affected individuals. EV detection and genotyping were performed using real-time RT-PCR and nested RT-PCR followed by sequence analysis. EV detection rate was found to be 82.3%, and the main genotype identified was CV-A6. Sixteen CV-A6 samples were selected for whole genome sequencing. According to phylogenetic analysis, all CV-A6 strains from this study belonged to the sub-genotype D3 clade based on VP1 sequences. Analysis of 3D polymerase phylogeny showed that only the recombinant RF-A group was identified. In conclusion, circulating EV types should be continuously monitored to understand pathogen emergence and evolution during the post-pandemic era.

The radar sensor described realizes healthcare monitoring capable of detecting subject chest-wall movement caused by cardiopulmonary activities, and wirelessly estimating the respiration and heartbeat rates of the subject without attaching any devices to the body. Conventional single-tone Doppler radar can only capture Doppler signatures because of a lack of bandwidth information with noncontact sensors. In contrast, we take full advantage of impulse radio ultra-wideband (IR-UWB) radar to achieve low power consumption and convenient portability, with a flexible detection range and desirable accuracy. A noise reduction method based on improved ensemble empirical mode decomposition (EEMD) and a vital sign separation method based on the continuous-wavelet transform (CWT) are proposed jointly to improve the signal-to-noise ratio (SNR) in order to acquire accurate respiration and heartbeat rates. Experimental results illustrate that respiration and heartbeat signals can be extracted accurately under different conditions. This noncontact healthcare sensor system proves the commercial feasibility and considerable accessibility of using compact IR-UWB radar for emerging biomedical applications.

Human Pose Estimation (HPE) is a technique in computer vision and AI for detecting and tracking human body parts and poses from images or videos. Widely used in augmented reality, animation, fitness applications, and surveillance, HPE methods using monocular cameras are highly versatile due to their applicability in standard video and CCTV footage. These methods have evolved from 2D to 3D pose estimation. However, current 3D HPE methods trained on laboratory-based motion capture data encounter challenges such as limited training data, depth perception ambiguity, left/right switching, and issues with occlusions when applied in real-world environments. This study compares two representative 3D HPE methods by assessing their strengths and weaknesses with real-world videos. Then, we propose data processing techniques to eliminate and correct anomalies like left/right inversion and false detections of joint positions in daily life motions. Finally, we obtain joint angle trajectories using an optimization method based on a 3D humanoid simulator, taking as input the joint coordinate data corrected by applying the proposed human joint data processing technique. The efficacy of the proposed 3D HPE method is verified by applying it to three-dimensional freehand gymnastics exercises and comparing the joint angle trajectories during the motion.

Background: Animal-assisted therapy has positive effects on cognitive function, depression, performance ability, and social functioning in elderly patients. The aim of this study was to evaluate the effects of rearing pet insects on the cognitive function of healthy elderly participants, with fMRI (functional magnetic resonance imaging) being used for this purpose. Methods: Community-dwelling elderly women (≥60 years) with normal cognitive function were enrolled during April 2015. They were randomized at a 1:1 ratio into two groups: insect-rearing and control (n=16) groups, with the insect-rearing group being further classified into two groups for analysis according to the subjects’ scores in the Wisconsin Card Sorting Test, WCST) at the first fMRI: insect-rearing group I with a relatively high score (n=13), and insect-rearing group II with a relatively low score (n=6). All subjects were educated on a healthy lifestyle for better cognitive function at every visit, and the insect-rearing groups received and reared crickets as pet insects. The fMRI was performed at baseline and after 8 weeks using the WCST as a stimulus. The WCST consisted of two variations, a high level baseline (HLB) and semi-WCST version. Results: There were no significant differences in the baseline characteristics among the three groups. There was a significant difference accuracy of the HLB–semi-WCST (p<0.05) in insect-rearing group II after 8 weeks from the baseline test. In the fMRI analysis involving the WCST reaction test, increased activation was observed in the right dorsal lateral prefrontal cortex and parietal cortex in insect-rearing group II when the semi-WCST, rather than the HLB, was performed. There were no significant differences in the other groups. Conclusion: The rearing of pet insects as an animal-assisted therapy is cost-effective, easy, and occupies little space. In this study, it showed positive effects on executive functions and performance improvement in elderly women. Further larger studies on the effects of pet insects on cognitive function are warranted.

Fibrillin (FBN) is a plastid lipid-associated protein found in photosynthetic organisms from cyanobacteria to plants. In this study, 10 CsaFBN genes were identified in genomic DNA sequences of cucumber (Chinese long and Gy14) through database searches using the conserved domain of FBN and the 14 FBN genes of Arabidopsis. Phylogenetic analysis of CsaFBN protein sequences showed that there was no counterpart of Arabidopsis and rice FBN5 in the cucumber genome. FBN5 is essential for growth in Arabidopsis and rice; its absence in cucumber may be because of incomplete genome sequences or that another FBN carries out its functions. Among the 10 CsaFBN genes, CsaFBN1 and CsaFBN9 were the most divergent in terms of nucleotide sequences. Most of the CsaFBN genes were expressed in the leaf, stem, and fruit. CsaFBN4 showed the highest mRNA expression levels in various tissues, followed by CsaFBN6, CsaFBN1, and CsaFBN9. High-light stress combined with low temperature decreased photosynthetic efficiency and highly induced transcript levels of CsaFBN1, CsaFBN6, and CsaFBN11, which decreased after 24 h treatment. Transcript levels of the other seven genes were changed only slightly. This result suggests that CsaFBN1, CsaFBN6, and CsaFBN11 may be involved in photoprotection under high-light conditions at low temperature.

Polo-like kinase 1 (PLK1) plays a pivotal role in cell division regulation and emerges as a promising therapeutic target for cancer treatment. Consequently, the development of small-molecule inhibitors targeting PLK1 has become a focal point in contemporary research. The adenosine triphosphate (ATP)-binding site and the polo-box domain in PLK1 present crucial interaction sites for these inhibitors, aiming to disrupt the protein's function. However, designing potent and selective small-molecule inhibitors can be challenging, requiring a deep understanding of protein-ligand interaction mechanisms at these binding sites. In this context, our study leverages the fragment molecular orbital (FMO) method to explore these site-specific interactions in-depth. Through the FMO approach, we used the FMO method to elucidate the molecular mechanisms of small-molecule drug binding to these sites to design PLK1 inhibitors that are both potent and selective. Our investigation further entailed a comparative analysis of various PLK1 inhibitors, each characterized by distinct structural attributes. This comparison enhanced our understanding of the structure-activity relationships of these inhibitors, underscoring the efficacy of the FMO method in identifying critical binding features and predicting binding modes for small-molecule ligands. Furthermore, Our research spotlighted "hot spot" residues instrumental for selective and robust PLK1 binding. Our findings offer profound insights, priming the rational design of innovative potential PLK1 inhibitors with significant implications for developing anticancer therapeutics.

Background Telomere shortening is related to aging and unfavourable health outcomes. Obesity and metabolic diseases are important factors for accelerating aging. This study aimed to find out the association between obesity, metabolic disease, and telomere length in metabolically healthy adults. Methods 237 adults were enrolled with written consents at a health promotion centre of a tertiary hospital from February 2014 to March 2015. After excluding 99 subjects who met the exclusion criterion, a total of 130 metabolically healthy subjects were selected for final analysis. The subjects were divided into quartile groups according to the telomere lengths of their oral mucosal cells. Results The subjects consisted of 66 (50.8%) males with a mean age of 58.59 years. The body mass index (BMI, kg/m2) increased significantly along with the quartile groups (Q1, 23.00; Q2, 23.96; Q3, 23.70; Q4, 25.20; P-for trend=0.008). Waist circumference (WC, P-for trend=0.022), waist-to-hip ratio (WHR, P-for trend=0.005), and waist-to-height ratio (WHtR, P=0.001) also increased along with the quartile groups. Obesity prevalence (BMI ≥25 kg/m2), abdominal obesity (WC ≥90 cm for men, ≥85 cm for women), WHR 〉1.0 for men or 〉0.85 for women, and WHtR ≥0.5 increased significantly as the telomere length increased (P-for trend <0.05). After adjusting for covariates, the ORs for each obesity markers increased as the telomere length increased (P-for trend <0.05); and the ORs of WHtR were especially meaningful (Q1, 1.00; Q2, 2.53; Q3, 2.97; Q4, 7.81; P-for trend = 0.001). There were no significant trends for metabolic syndrome and its components along with the prevalence of fatty liver disease. Conclusion Obesity markers and telomere length had significant positive correlation despite the established theory. The obesity paradox may exist in metabolically healthy adults with regard to telomere length, However, further studies with larger sample sizes for the association between obesity and telomere length are needed.

As renewable energy generation prediction systems have been introduced into the energy trading market, accurate prediction of solar photovoltaic (PV) energy generation has become a crucial challenge for ensuring stable trade of variable energy. Therefore, it is essential to quantitatively investigate and analyze current prediction technology and develop more advanced prediction systems. In this study, three models for predicting PV energy generation were investigated. Multiple regression, random forest, and gradient boosting machine (GBM) models were con-structed for 15 utility-scale power plants throughout South Korea. Model performance was evaluated in terms of root mean square error (RMSE) and mean absolute error (MAE). The multiple regression-based model had an RMSE of 12.00% and MAE of 9.06%. The random forest model had an RMSE of 11.69% and MAE of 8.61%. The GBM model had an RMSE of 11.34% and MAE of 8.18%, indicating its superior accuracy among the three models in predicting PV energy generation. These findings provide valuable insights that may contribute to the development of advanced PV energy generation models and their application in grid operations.

Objectives: Essential thrombocythemia (ET) is a chronic myeloproliferative neoplasm characterized by elevated platelet counts and an increased risk of thrombotic events, including ischemic strokes. Methods: We conducted a retrospective analysis of data from consecutive ischemic stroke patients with ET between March 2014 and February 2023. Results: This case series describes the clinical presentation, radiological features, and management of five patients with ET-associated ischemic strokes, all harboring the JAK2 mutation. The diverse radiological findings suggest that both large and small vessel diseases may be influenced by the prothrombotic state induced by ET. A significant elevation in platelet count was observed to correlate with the emergence of new acute infarctions in some cases. Conclusions: The study highlights combined use of antiplatelet and cytoreductive therapy in preventing secondary stroke events in patients with ET and JAK2 mutations. The heterogeneity of stroke patterns in this population necessitates a comprehensive understanding of the underlying pathophysiological mechanisms and tailored therapeutic approaches.

In traditional oriental medicine, carrots (Daucus carota L.) are considered effective medicinal herbs; however, the use of D. carota leaves (DGL) as therapeutic agents has not been explored in depth. Therefore, we aimed to demonstrate the value of DGL, generally treated as waste while developing plants for wide industrial availability. Six flavone glycosides were isolated and identified from DGL, and their constituents were identified and quantitated using an NMR and HPLC/UV method, which was optimized and validated. The structure of chrysoeriol-7-rutinoside from DGL was elucidated for the first time. The method exhibited adequate relative standard deviation (&lt;1.89%) and recovery (94.89–105.97%). The deglycosylation of DGL flavone glycosides by Viscozyme L and Pectinex was assessed. Upon converting the reaction contents to percentages, the luteolin, apigenin, and chrysoeriol groups showed values of 85.8, 33.1, and 88.7%, respectively. The enzyme-treated DGL had a higher inhibitory effect on TNF-α and IL-2 expression than that of the carrot roots or carrot leaves without enzyme treatments. These results highlight the importance of carrot leaves and could be used as baseline standardization data for commercial development.

The ubiquitous presence of microplastics (MPs) in the environment poses a threat to ecosystems and increases concerns about their exposure to the human body. However, despite being consumed for health improvement, limited research has been conducted on MPs in functional foods. This study aimed to investigate the occurrence of MPs and the relation of the source of raw material or the manufacture in various omega-3 oil in the Korean market. MPs in omega-3 capsule and raw oil, sourced from both plant-based (PB) and animal-based (AB) sources, were investigated. We developed the method by direct filtration with acetone washing and analyzed MPs greater than 5 μm using microscope-Raman spectroscopy. The average number of MPs was found to be 1.2 ± 1.7 MPs/g for PB raw oil, 2.2 ± 1.7 MPs/g for AB raw oil, 3.5 ± 3.9 MPs/g for PB capsule oil, and 10.6 ± 8.9 MPs/g for AB capsule oil. Polypropylene and polyethylene terephthalate were major specious (83-95 %) found in omega-3 oil. The ratio of size range remained consistent across all groups, with a trend of higher detection rates as the size diminished. The results reveal that the main reason of MPs contamination is not the source of raw material but the manufacturing and packaging process for omega-3 oil.

Metal oxide p-n heterojunction nanofibers (NFs) are among the most promising approaches to enhancing the efficiency of gas sensors. In this paper, we report the preparation of a series of p-NiO-loaded n-ZnO NFs, namely (1 − x) ZnO-xNiO (x = 0.03, 0.05, and 0.1 wt%), for hydrogen gas sensing experiments. Samples were prepared through the electrospinning technique followed by a calcination process. The sensing experiments showed that the sample with 0.05 wt% NiO loading resulted in the highest sensing performance at an optimal sensing temperature of 200 °C. The sensing mechanism is discussed in detail and contributions of the p-n heterojunctions, metallization of ZnO and catalytic effect of NiO on the sensing enhancements of an optimized gas sensor are analyzed. This study demonstrates the possibility of fabricating high-performance H₂ sensors through the optimization of p-type metal oxide loading on the surfaces of n-type metal oxides.

Cell-culture meat is a novel concept to replace traditional meat produced from animals, and to satisfy rising food demands due to the world population growth. It is still a young field and requires to solve technical issues including cell sources and types, efficient culture for large scale production, taste and texture for customer satisfaction. The current review summarized traditional beef meat production and evaluation methods for customer satisfaction. In particular, serum biomarkers for beef meat evaluation are discussed, which can be applicated for cell-culture meat production.

The introduction of electrical vehicle charging infrastructure including EV charger, renewable energy resource at secondary feeder in distribution system has been increased as one of countermeasure for global environmental issues. However, the Electric Vehicle Charging (EVC) infrastructure may act as the peak load in distribution system, which can adversely impact on the voltage stability when the electric vehicle is quickly charged. Therefore, to keep within the limit capacity of secondary feeder and allowable limit for feeder voltage, this paper proposes a stabilization method by the Energy Storage System (ESS) control strategy at secondary feeder in order to be not violated over than lower and upper limit. Also, this paper presents the estimation method to keep the proper standard value of State of Charge (SOC). From the simulation results, the voltage stabilization operation by ESS should make the feeder voltages of the distribution system(secondary feeder) introduced EVC Infra keep better voltage conditions, also estimation method to keep the proper standard value is confirmed that the SOC of ESS when is the standby condition could be exactly kept within the proper reference range.

Purpose To investigate the effects of intra-articular glenohumeral joint triamcinolone injection in treating secondary adhesive capsulitis after breast cancer surgery.Methods This study prospectively enrolled 37 participants, 22 of the breast cancer surgery group and 15 of the idiopathic group. All participants received intra-articular glenohumeral joint injection in the affected shoulder joint and received physiotherapy for 12 week. The clinical assessment evaluated before, and 1, 3, and 6 months after the intervention. The primary outcome was the change in the Shoulder Pain and Disability Index (SPADI).Results The total SPADI(%) in both groups showed significant decrease from baseline to 1, 3, and 6 months after the intervention. There was no significant difference in the differences of the total SPADI from baseline to 1, 3, and 6 months between two groups. However, the improvement in the SPADI pain subscale and the PROM of abduction at 3 and 6 months post-injection in the breast cancer group were inferior to the idiopathic group.Conclusion Intra-articular triamcinolone injection for adhesive capsulitis after breast cancer surgery significantly improved in significant improvements of pain, shoulder function and the PROM. The effects were similar to idiopathic adhesive capsulitis, but in the breast cancer surgery group, appropriate pain and ROM management and monitoring are required even 3 months after injection. With a standardized injection protocol, intra-articular triamcinolone injection could be an effective and safe treatment option for secondary adhesive capsulitis after breast cancer surgery.

Rice prolamins are categorized into three groups by molecular size (10, 13, or 16 kDa), while the 13 kDa prolamins are assigned to four subgroups (Pro13a-I, Pro13a-II, Pro13b-I, and Pro13b-II) based on cysteine residue content. Here, we generated four knockout strains of rice using CRISPR-Cas9, each of which demonstrated selectively reduced expression of specific subgroups of the 13 kDa prolamins. These four mutant rice lines also demonstrated compensatory expression of glutelins and non-targeted prolamins, which resulted in low grain weight, altered starch content and atypically-shaped starch granules and protein bodies. Transcriptome analysis identified 746 transcripts that were differentially expressed in the mutant rice lines during development. These transcripts played roles primarily in RNA processing, protein synthesis, stress response, and transport. After selective suppression/knockout of genes in the Pro13a-I subgroup, compensatory upregulation of genes in the Pro13a-II and Pro13b-I/II subgroups was observed. Compensatory expression of 9 ER stress and 17 transcription factor genes was also observed in mutant rice in which expression of 13 kDa prolamin genes was suppressed. Our results provide valuable insight into the regulatory mechanisms underlying rice seed development and the specific roles played by 13 kDa rice prolamins and their target genes.

In this study, the effect of heat treatment was investigated to influence the occurrence of fracture during manufacturing process of Alloy B steel with boron contents as high as 130 ppm. As the content of boron increases, it affects the phase transformation temperature and texture. The development of {111}<uvw> components in the γ-fiber is affected depending on the austenite fraction after phase transformation. The Alloy B steel indicated that the increase in the boron content increased the α to γ phase transformation temperature such that sufficient transformation did not occur in the normalizing condition. The cracks occurred at the point of the transition from elastic to plastic deformation in the ND direction during the rolling process, thereby resulting in failure. Therefore, it is necessary to avoid the intermediate heat treatment condition in which γ-fiber does not fully develop, i.e., an imperfect normalization.

This study delves into the critical domain of public procurement, specifically focusing on Sustainable Public Procurement (SPP) and Environmental, Social, and Governance (ESG) considerations within the context of South Korea. The aim of this research is to empirically scrutinize the factors influencing the impact index of SPP, with a particular emphasis on services related to labor standards. The investigation spans three years, from January 1, 2019, to July 31, 2021, encompassing state agency orders and post-implementation legal changes. Leveraging the comprehensive Korea On-line E-Procurement Sys-tem(KONEPS) platform, we meticulously collected data, ultimately culminating in 21,573 services meeting our criteria, from which 250 cases underwent an in-depth analysis. The study sheds light on the influence of social responsibility evaluation cri-teria on overall procurement scores, while also uncovering the moderating effects of various factors. The outcomes of this study offer valuable insights into the impact index of social responsibility evaluation criteria within South Korea's public procurement landscape. Factors including procurement year, classification, service period, and estimated price were identified as significant influencers. Moreover, the number and location of evalu-ation criteria items, inclusion of sincerity elements, and the evaluating agency were deemed pivotal determinants of the influence index. These findings hold profound implications for policymakers, procurement practitioners, and researchers and provide a roadmap for optimizing the utilization of social responsibility evaluation criteria to advance responsible and sustainable procurement practices. Future research avenues include conducting further study of additional moderat-ing variables, expanding datasets to encompass a broader spectrum of procurement contexts, and evaluating the long-term repercussions of social responsibility evaluation on procurement outcomes. These endeavors promise to further refine and advance public procurement practices in South Korea and beyond.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

Rammed earth in a built environment has vapor diffusion characteristics and humidity control ability each of which are respectively attributed to the porous structures and the hydrophilic properties. Indeed, these structures and properties, which allows easily absorbing water parti-cles, hence, affecting the durability of a rammed earth wall. This paper presents the water repel-lency method for rammed earth walls which synthesizes siloxane copolymers containing fluo-rine. The water-repellent properties are investigated by measuring the contact angle, water ab-sorption rate, and compressive strength after spray coating with the synthesized siloxane co-polymers on the surface of the rammed earth specimens under study. The water contact angle of the specimen coated with a siloxane copolymer containing 10 mol.% of a silane monomer with a fluorine group is about 140o. The water absorption of the specimen obtained after immersing in water for 24 hours is low at about 3.5 wt.%. In addition, the compressive strength is remained more than 80% of the corresponding strength of the specimen which is not immersed into water. It is confirmed that the use of a 10% by volume of the siloxane copolymer containing the fluo-rine group may assure the water-repellent performance and the economic competitiveness.

Objective: To explore the hot spots and development trends of community public health research. Methods: The literature related to this topic was searched in CNKI and PubMed databases, and the trend map of the number of articles was drawn according to the obtained data. The included literature were analyzed with Vosviewer software for keyword and author co-occurrence, and CiteSpace 6.3.R1 Basic software was used for mechanism co-occurrence, key emergence and clustering analysis, and timeline distribution map drawing. Results: 189 Chinese literature and 77 English literature were selected. The Chinese literature focused on “community public health service, emergency management, and community governance”, and the research trend was “community public health emergency management and community governance”; English literature focuses on “nursing education, health education, human qualitative research”. Conclusion: Although the Chinese and English literature shows that scholars in this field have different emphases, the primary community health is the key and difficult point to realize the national public health service project, and improving the basic public health service in the primary community is related to the health of all the people, so it is very important.

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) is a promising chemotherapeutic agent because of its selective apoptotic action on cancer cells. However, resistance to TRAIL-induced apoptosis remains a challenge in many cancers. The gintonin-enriched Panax ginseng extract fraction (GEF) has diverse pharmacological benefits. We explored the combined efficacy of GEF and TRAIL in inducing apoptosis in human renal cell carcinoma (RCC) cells. The effect of GEF treatment on viability, clonogenic potential, wound healing, and TRAIL-induced apoptotic signaling of RCC cells was studied in vitro. Our investigation revealed that GEF pre-treatment sensitized RCC cells to TRAIL-induced apoptosis, as evidenced by DNA fragmentation and cell proliferation, colony formation, and migration inhibition. This sensitization was linked to the upregulation of death receptors 4 and 5 and alterations in apoptotic protein expression; notably, decreased expression of Mu-2-related death-inducing gene, a novel anti-apoptotic protein. Our findings underscore the necessity of caspase activation for GEF/TRAIL-induced apoptosis using the pan-caspase inhibitor Z-VAD-FMK. It demonstrates that GEF sensitizes human RCC cells to TRAIL-induced apoptosis by upregulating DR4/5 and modulating apoptotic protein expression. These findings suggest a promising strategy for overcoming TRAIL resistance in cancer therapy and highlight the potential of GEF as a valuable adjunct to TRAIL-based treatments.

We fabricated the nano-aperture plasmonic platforms for single molecule detection and other various applications such as infrared thermal emission device. The nano-apertures including the nanopores on the pyramid, and the nano-slits on the Au flat membrane were fabricated using a Ga ion focused ion beam drilling technique, followed by high energy electron beam irradiations dependent upon the electron beam current density. The nanopores with a few nanometer size and the nanoslit array with order of ~ 100 nm width were fabricated. Optical characteristics for the various nanoslits were examined dependent upon the slit opening width and sample thickness. The broad emission spectra from the (7x 7) slit array are obtained from spp-mediated emission in the visible and infrared region. A sharp strong infrared emission peak is also obtained due to Au nanoparticle. The fabricated Au platform can be utilized as single molecule sensor and infrared thermal emission device.

Although health policy resides mainly with the government, industry can play an important role in building a health ecosystem. From March to May, we administered questionnaires to 1,200 individuals from the general Korean population asking about their perception of health-friendly labels, and if they would purchase such labeled products (foods, pharmaceuticals, etc.) and services (purifying water, preventing air pollution, etc.) at extra cost. The participants placed a high value on the importance of mental, social, spiritual, and physical health factors in terms of company’s products and services with a score of about 8 out of 10 (range, 7.74-8.33). Most respondents (72.4%) said they were interested in adopting health-friendly labels. When a health-friendly label is introduced (such as one by the Business for Social Responsiveness), 65.1% of the respondents said they intended to purchase the product or service, while 6.8% said they did not, and 75.0% said they were willing to pay extra for the health-friendly product or service. Multivariate logistic regression models showed urban residence, high education level, and good social health to be significantly associated with positive attitudes toward health-friendly labels. People with high income, no religion, or normal weight were more likely to say they intend to purchase products and services with health-friendly labels. They also had a more positive attitude toward paying more for such products and services, as did people with good spiritual health. This study provides data that illustrate the importance of health-friendly products and services to the general population and companies.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

The diffusion coefficients of ions are measured in a microchip filled with a cationic charged 3D hydrogel in order to study the effect of cationic charged 3D hydrogel on the diffusivity of ions. In this study, poly-diallyl-dimethyl-ammoniumchloride (poly-DADMAC) is used to produce a 3D hydrogel. Four different fluorophores are used in the 3D hydrogel rhodamine 6G, rhodamine-BSA, fluorescein isothio-cyanate (FITC) and FITC-BSA. The rhodamine 6G and rhodamine-BSA are positively charged (cations), while fluorescein isothio-cyanate (FITC) and FITC-BSA are negatively charged (anions). Two widely used techniques which are short time diffusivity measurement technique and long time diffusivity measurement techniques are used to measure the diffusion coefficients. For the short time measurement, Fluorescence recovery after photo-bleaching (FRAP) is used by a 3D confocal microscope. For the long time measurement, fluorescence images are taken for 11 days to observe a pure diffusivity without any convective movement. As a result, the diffusivity of the cations was found to be lower than that of the anions in the cationic charged hydrogel.

Especially for drought periods, the higher the accuracy of reservoir inflow forecasting, the more reliable the water supply from a dam. The article focuses on probabilistic forecasting of seasonal inflow to reservoirs and determines estimates from the probabilistic seasonal inflow according to drought forecast results. The probabilistic seasonal inflow was forecasted by a copula-based Bayesian network employing a Gaussian copula function. Drought forecasting was performed by calculation of the standardized streamflow index value. The calendar year is divided into four seasons; the total inflow volume of water to a reservoir for a season is referred to as the seasonal inflow. Seasonal inflow forecasting curves conforming to drought stages produce estimates of probabilistic seasonal inflow according to the drought forecast results. The forecasted estimates of seasonal inflow were calculated by using the inflow records of Soyanggang and Andong dams in the Republic of Korea. Under the threshold probability of drought occurrence ranging from 50 to 55 %, the forecasted seasonal inflows reasonably matched critical drought records. Combining the drought forecasting with the seasonal inflow forecasting may produce reasonable estimates of drought inflow from the probabilistic forecasting of seasonal inflow to a reservoir.

Urbanization is considered as a main indicator of regional economic development due to its positive effect on promoting industrial development; however, many regions, especially developing countries, are troubled by its negative effect — the aggravating environmental pollution. Many researchers have indicated that rapid urbanization stimulated the expansion of industrial production scale and increased industrial pollutant emissions. However, this judgement contains a grave deficiency in that urbanization not only expands industrial production scales but can also increase industrial labour productivity and change the industrial structure. To modify this deficiency, we first decompose the influence which urbanization impacts on industrial pollutant emissions into the scale effect, the intensive effect and the structure effect by using the Kaya Identity and the LMDI Method; second, we perform an empirical study of the three effects’ impacts by applying the spatial panel model with data from 282 Chinese cities between 2003 and 2013. Our results indicate that (1) there are significant reverse U-shapes between Chinese urbanization rate and its industrial pollutant emissions; (2) the scale effect and the structure effect have aggravated Chinese industrial waste water discharge, sulphur dioxide emissions and soot (dust) emissions, while the intensive effect has generated a decreasing and ameliorative impact on that aggravated trend. The definite relationship between urbanization and industrial pollutant emissions depends on the combined influence of the scale effect, the intensive effect and the structure effect; (3) there are significant spatial autocorrelations of industrial pollutant emissions between Chinese cities, but the spatial spillover effect from other cities does not aggravate local urban industrial pollutant emissions, we offer an explanation to this contradiction that the vast rural areas surrounding Chinese cities have served as sponge belts and have absorbed the spatial spillover of cities’ industrial pollutant emissions. According to the results, we argue that this type of decomposition of the influence into three effects is necessary and meaningful, it establishes a solid foundation for understanding the relationship between urbanization and industrial pollutant emissions, and effectively helps to meet relative policy making.

We developed an ovarian cancer-targeted drug delivery system based on a follicle-stimulating hormone receptor (FSHR) peptide. The lipophilic chemotherapeutic drug SN38 and the photosensitizer IR820 were loaded into the phospholipid bilayer of liposomes. Near-infrared laser irradiation stimulated the generation of reactive oxygen species, causing short-term reactive molecular species and spatial-temporal restricted photodamage to the biological targets. The reactive molecular species and spatial-temporal restricted photodamage enhanced the release and uptake of chemotherapy drugs and increased the sensitivity to chemotherapy drugs in ovarian cancer cells. FSH liposomes loaded with SN38 and IR820 (SN38/IR820-Lipo@FSH) were prepared using thin-film hydration-sonication. FSH peptide binding was analyzed using 1H NMR spectrum and Maldi-Tof. The average size and zeta potential of SN38/IR820-Lipo@FSH were 105.1 ± 1.15 nm (PDI: 0.204 ± 0.03) and −27.8 ± 0.42 mV, respectively. SN38/IR820-Lipo@FSH exhibited good drug-loading properties and the in vitro release was slow. FSH significantly increased the uptake of liposomes, inhibited cell proliferation, and induced apoptosis in A2780 cells. Moreover, SN38/IR820-Lipo@FSH exhibited good tumor-targeting ability and anti-ovarian cancer activity in vivo. The SN38/IR820-Lipo@FSH exhibited specific targeting to A2780 ovarian cancer cells. The combination of chemotherapy and photodynamic treatment based on an FSH peptide-targeted delivery system may be an effective approach to treating ovarian cancer.

Weight-bearing computed tomography (WBCT) enables acquisition of three dimensional bony structure images in a physiological weight-bearing position, which is fundamental in under-standing the pathologic lesions and deformities of the ankle joint. Over the past decade, re-searchers focused on validating and developing WBCT measurements, which has significantly enhanced our knowledge of common foot and ankle disease. Consequently, understanding the application of WBCT in clinical practice is becoming more important to produce improved out-comes in the treatment of disease around the ankle joint. This review will describe an overview of what is currently being evaluated in the foot and ankle surgery using WBCT and where the course of research will be heading in the future.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Longitudinal cutting is a most common process in steel structure manufacturing, and the man-hours of the process provide an important basis for enterprises to generate production schedules.However, currently the man-hours in factories are mainly estimated by experts, and the accuracy of this method is relatively low.In this study,we propose a system that predicts man-hours with history data in the manufacturing process and that can be applied in practical structural steel fabrication.The system addresses the data inconsistency problem by one-hot encoding and data normalization techniques,Pearson correlation coefficient for feature selection,and the Random Forest Regression(RFR) for prediction.Compared with the other three Machine Learning(ML) algorithms, the Random Forest algorithm has the best performance.The results demonstrate that the proposed system outperforms the conventional approach and has better forecast accuracy, so that it is suitable for man-hours prediction.

Human milk reduces risk for necrotizing enterocolitis in preterm infants. Necrotizing enterocolitis occurs in the ileocecal region where thousands of milk protein-derived peptides have been released from digestion. Digestion-released peptides may exert bioactivity, such antimicrobial and immunomodulatory activities, in the gut. In this study, we applied mass spectrometry-based peptidomics to characterize peptides present in colostrum before and after in vitro digestion. Sequence-based computational modeling was applied to predict peptides with antimicrobial activity. We identified more peptides in undigested samples, yet the abundances were much higher in the digested samples. Heatmapping demonstrated highly different peptide profiles between undigested and digested samples. Four peptides (αS1-casein [157–163], αS1-casein [157–165], β-casein [153–159] and plasminogen [591–597]) were selected, synthesized and tested against common pathogenic bacteria associated with necrotizing enterocolitis. All four exhibited bacteriostatic, though not bactericidal, activities against Klebsiella aerogenes, Citrobacter freundii and Serratia marcescens, but not Escherichia coli.

Reinforcement Learning (RL) has demonstrated considerable potential in solving challenges across various domains, notably in autonomous driving. Nevertheless, implementing RL in autonomous driving comes with its own set of difficulties, such as the overestimation phenomenon, extensive learning time, and sparse reward problems. Although solutions like Hindsight Experience Replay (HER) have been proposed to alleviate these issues, the direct utilization of RL in autonomous vehicles remains constrained due to the intricate fusion of information and the possibility of system failures during the learning process. In this paper, we present a novel RL-based autonomous driving system technology that combines Obstacle Dependent Gaussian (ODG) RL, Soft Actor-Critic (SAC), and meta-learning algorithms. Our approach addresses key issues in RL, including the overestimation phenomenon and sparse reward problems, by incorporating prior knowledge derived from the ODG algorithm. We evaluated our proposed algorithm on official F1 circuits, using high-fidelity racing simulations with complex dynamics. The results demonstrate exceptional performance, with our method achieving up to 89% faster learning speed compared to existing algorithms in these environments.

Osteoporosis is an abnormal bone remodeling condition characterized by decreased bone density, which leads to high risks of broken bones. Previous studies have demonstrated that Lycii Radicis Cortex (LRC) extract inhibits bone loss in ovariectomized (OVX) mice by enhancing the osteoblast differentiation. A bioactive compound, Kukoamine B (KB), was identified from a fractionation of LRC extract as a candidate component responsible for an anti-osteoporotic effect. This study investigated the anti-osteoporotic effects of KB using in vitro and in vivo osteoporosis models. KB treatment significantly increased the osteoblastic differentiation and mineralized nodule formation of osteoblastic MC3T3-E1 cells, while it significantly decreased the osteoclast differentiation of primary-cultured monocytes derived from mouse bone marrow. The effects of KB on osteoblastic and osteoclastic differentiations under more physiological conditions were also examined. In the co-culture of MC3T3-E1 cells and monocytes, KB promoted osteoblast differentiation but did not affect osteoclast differentiation. For the in vivo experiments, KB significantly inhibited OVX-induced bone mineral density loss and restored the impaired bone structural properties in osteoporosis model mice. These results suggest that KB may be a potential therapeutic candidate for the treatment of osteoporosis.

Postbiotics are biologically active probiotic microorganisms that have produced non-viable bacterial products in the host. Eating a diet high in probiotic and prebiotic foods may help to ensure that the gut has an appropriate supply of these essential nutrients because postbiotics are produced when probiotics feed on prebiotics. Cell wall components and metabolites produced by living bacteria that have positive effects on the host are referred to as postbiotics. Postbiotics are functional bioactive chemicals that are produced in a matrix during anaerobic fermentation of organic nutrients like prebiotics. Postbiotics are low molecular weight soluble chemicals that are either produced after microbial cell lysis or secreted by live microflora as byproducts of this metabolic process. In general, the producer strains from bacterial and fungal species such as Lactobacillus, Bifidobacterium, Streptococcus, Akkermansia muciniphila, Saccharomyces boulardii, Eubacterium hallii, Faecalibacterium, etc. When handling and selling food items in an industrial setting, postbiotics can be used as functional components in foods, which has a number of advantages, including the potential to be added to some foods that are known to be harmful to probiotic survival. Postbiotic supplements have grown in popularity among customers because of their numerous health advantages, particularly food, cosmetic, and healthcare industries. Classification of postbiotics depends on various factors including type of microorganism, structural composition, and physiological functions. This review presents a succinct introduction, history, and concept of postbiotics, the salient features of postbiotics, classification, production, purification, characterization, biological functions, and applications of postbiotics in the food industry.

With improved measurement and modelling technology, variability has emerged as an essential feature in non-equilibrium processes. While traditionally, mean values and variance have been heavily used, they are not appropriate in describing extreme events where a significant deviation from mean values often occurs. Furthermore, stationary Probability Density Functions (PDFs) miss crucial information about the dynamics associated with variability. It is thus critical to go beyond a traditional approach and deal with time-dependent PDFs. Here, we consider atmospheric data from the Whole Atmosphere Community Climate Model (WACCM) and calculate time-dependent PDFs and the information length from these PDFs, which is the total number of statistically different states that a system passes through in time. Time-dependent PDFs are shown to be non-Gaussian in general, and the information length calculated from these PDFs shed us a new perspective of understanding variabilities, correlation among different variables and regions. Specifically, we calculate time-dependent PDFs and information length and show that the information length tends to increase with the altitude albeit in a complex form. This tendency is more robust for flows/shears than temperature. Also, much similarity among flows and shears in the information length is found in comparison with the temperature. This means a stronger correlation among flows/shears because of a strong coupling through gravity waves in this particular WACCM model. We also find the increase of the information length with the latitude and interesting hemispheric asymmetry for flows/shears/temperature, a stronger anti-correlation (correlation) between flows/shears and temperature at a higher (low) latitude. These results also suggest the importance of high latitude/altitude in the information budge in the Earth's atmosphere, the spatial gradient of the information as a useful proxy for the transport of physical quantities.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

Evans' Syndrome (ES) is a rare autoimmune disorder characterized by the simultaneous occurrence of immune thrombocytopenia (ITP) and autoimmune hemolytic anemia (AIHA). Thrombotic complications in ES patients are uncommon, particularly involving Buerger's Disease (BD). We report a case of a 49-year-old male with ES and a history of diabetes and heavy smoking, presenting with a necrotic wound on his right great toe. Diagnostic evaluations revealed severe stenosis and thrombosis in the lower limb arteries, diagnosed as BD. The patient underwent successful popliteal-tibioperoneal artery bypass surgery and subsequent disarticulation and revision of the distal phalanx, followed by the application of an acellular dermal matrix (ADM) to promote healing. Post-surgery, the patient showed significant improvement in blood flow and complete epithelialization without complications. This case highlights the importance of a multidisciplinary approach in managing complex wounds in ES patients, suggesting potential treatment pathways for future cases involving BD

The calmodulin-binding transcription activators (CAMTAs) mediate transcriptional regulation of development, growth, and responses to various environmental stresses in plants. To characterize the biological processes of soybean CAMTA (GmCAMTA) family members in response to abiotic stress, we identified 15 GmCAMTA genes from soybean (Glycine max L.) and investigated their roles in the abiotic stress response. The transcriptions of GmCAMTAs exhibited distinct circadian regulation patterns and were expressed differently in response to salt, drought, and cold stresses, except ABA. Interestingly, the expression levels of GmCAMTA2, GmCAMTA8, and GmCAMTA12 were higher in stem tissue than in other soybean tissues. To determine the roles of GmCAMTAs in the regulation of developmental processes and stress responses, we isolated GmCAMTA2 and GmCAMTA8 cDNAs from soybean and generated Arabidopsis overexpressing transgenic plants. The GmCAMTA2-OX and GmCAMTA8-OX plants showed hypersensitivity to drought stress. The water in the leaves of GmCAMTA2-OX and GmCAMTA8-OX plants was lost faster than that in WT plants under drought stress conditions. In addition, stress-responsive genes in the GmCAMTA2-OX and GmCAMTA8-OX plants were down-regulated under drought stress conditions. Our results suggest that GmCAMTA2 and GmCAMTA8 genes are regulated by circadian rhythms and function as negative regulators in development and drought stress responses.