The lithium-ion batteries are widely used as a power source for portable devices, including cell phones. The useful life is about 2 years or 500 cycles, contributing to the generation of waste from electrical and electronic equipment (WEEE). Mining of lithium and cobalt damages the environment and is onerous; therefore, sustainable alternatives, such as obtaining these elements from secondary sources as recycling of lithium-ion batteries, are essential to provide the inputs used in the sector. However, the metallurgical route which will used to recovering them must be considered, due to this work aims for a more environmentally favorable process using DL-malic acid 1.5 M and instead of compared with sulfuric acid 2 M, heat pretreatment of 1 h and 3 h, and for all conditions, experiments were carried out with and without adding the oxidizing agent hydrogen peroxide. The best yields occurred in presence of H2O2 10 % v/v, and heat pretreatment of 1 h: 33.49 % Co and 4.63 % Li, and 29.78 % Co e 3.44 % Li were recovered by sulfuric acid and DL-malic acid, respectively.

Epithelial–mesenchymal transition (EMT) is defined as a cellular process during which epithelial cells acquire mesenchymal phenotypes and behavior following the downregulation of epithelial features. EMT and its reversed process, the mesenchymal-epithelial transition (MET), and the special form of EMT, the endothelial-mesenchymal transition (EndMT), have been thought as a universal dogma controlling developmental and pathological processes. More than half a century of EMT study has made it a large research field and a mainstream concept. However, discrepancies and disputes over EMT and EMT research have also grown over time. Particularly, neither the epithelial and mesenchymal states/properties nor their regulatory networks nor specific markers have been defined, rendering the EMT, MET and EndMT concepts groundless. Moreover, EMT and MET effects should not be a cause, but rather a consequence of or an accompanying effect during developmental and pathological processes. EMT and MET represented by the change in cell shapes or adhesiveness or symbolized by EMT factors are biased interpretation of the overall change in cellular property and regulatory networks during development and cancer progression. The true meaning of EMT effects in some developmental and pathological processes, such as fibrosis, needs re-evaluation. But the core EMT factors are actually a few components of the regulatory networks of neural stemness, which determines tumorigenicity and pluripotency. The EMT effects in cancer progression and neural crest formation are wrong attribution of the role of neural stemness during cancer progression and the cell-intrinsic property of neural crest cells to the unknown mesenchymal state. It is time to reassess the significance of EMT and its related concepts in scientific research.

In the paper, by virtue of some properties for the Riemann zeta function, the author finds a double inequality for the ratio of two consecutive Bernoulli numbers with even indexes and analyzes the approximating accuracy of the double inequality.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

We presented unusual case of double left ventricular false aneurysm complicating late presentation AMI successfully treated with the combination of urgent surgical drainage of tamponade, staged PCI of non-culprit lesion, preventive implantation of ICD-DR, guideline directed heart failure medical therapy and delayed but effective reconstructive operation.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

We consider a model of predator-prey interaction at fractional-order where the predation obeys the ratio-dependent functional response and the prey is linearly harvested. For the proposed model, we show the existence, uniqueness, non-negativity as well as the boundedness of the solutions. Conditions for the existence of all possible equilibrium points and their stability criteria, both locally and globally, are also investigated. The local stability conditions are derived using the Magtinon's theorem, while the global stability is proven by formulating an appropriate Lyapunov function. The occurance of Hopf bifurcation around the interior point is also shown analytically. At the end, we implement the Predictor-Corrector scheme to perform some numerical simulations.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

Liver fibrosis is based on complex interactions between extracellular matrix-producing hepatic stellate cells and is defined as excessive matrix deposition and an abundance of infiltrating cells in the liver. Studying these processes requires in vitro and in vivo experimental work on animals. In fibrosis research, experimental work in rodents is currently the gold standard for confirming a proposed disease-associated mechanism. Bile duct ligation (BDL) induces obstructive jaundice resulting in cholestasis. BDL is useful for preclinical research studies of liver injury due to extrahepatic cholestasis such as apoptosis and fibrosis. Here we provide a stepwise surgical approach to resect the common bile duct and monitor in situ hepatic metabolism by microdialysis.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

As the global aging trend continues to intensify, there will inevitably be more complex and diverse aging problems in the future. There is no doubt that designers have the responsibility to explore the possibilities of the future and solve the problems that will be faced in the future. Based on the Future Cone, the Double Diamond Model and the IDEO Method Cards, this study proposes a new model to guide the design practice of future aging issues in the context of aging. With the aim of validating and refining the framework, an ageing designer workshop was held where participants were asked to imagine, explore and express ideas about future ageing issues. The workshop was used to refine the proposed model. More specifically, the model includes a future concept, a design guidance process based on the Double Diamond Model, and tools that can be applied at all stages of design, which can help designers generate ideas and solutions for future aging problems, and collectively lead society to a more desirable future. Moreover, this study also explores broader directions for the development of the model and provides a reference for continued research on this topic in the future.

Introduction: The identification of some prognostic markers in head and neck cancers (HNC) is necessary for the stratification of the therapeutic approach with benefits in increasing treatment response rates and limiting the toxic side effects of treatments. Neutrophil-to-lymphocyte ratio (NLR), lymphocyte-to-monocyte ratio (LMR) and pallets-to-lymphocyte ratio (PLR) are currently validated as cheap and accessible biomarkers in different types of solid tumors. The purpose of the study was to evaluate the possible biomarker value of NLR, PLR and MLR recorded pre-treatment (radiotherapy/chemotherapy) for prognostic purposes in HNC. Materials and methods: The study included 190 patients with HNC included in the oncology record in the oncology outpatient clinic of the Craiova County Emergency Hospital starting from January 2002 and deceased until December 2022. Among them, 40 patients treated multimodally in the Clinic were included in the study of Oncology of the Craiova County Emergency Hospital for which the pre-treatment value (chemotherapy/radiotherapy) of NLR, PLR and MLR could be calculated. Overall survival (OS) values were correlated with NLR, PLR and MLR. Results: Median values for NLR, PLR and MLR were 6.15 (1.24-69), 200.79 (61.3- 1775.0) and 0.53 (0.12-5.5) respectively. In the study, the mean values for NLR, PLR and MLR of 2.88, 142.97 and 0.36 respectively were obtained. Median OS in the study group was 11 months (1-120). Although a negative Pearson`s correlation, the relationship between your variables was only weak, values R =.07, p=.67; R=.02, p=.31 and R=07, p=.62 being related with NLR, PLR and MLR respectively correlation with overall survival (OS). The median values of NLR, PLR and MLR were calculated (1.53, 90.32 and 0.18 respectively) for HNC cases with pre-treatment values of NLR <2 and for HNC cases with NLR values ≥6 (23.5, 232.78 and 0.79 respectively). Median OS for cases with NLR<2 and NLR≥6 were 17.4 and 13 months, respectively. Conclusions: The negative correlations of NLR, PLR and MLR with OS reported in the study are in accordance with the data reported in the literature for locally advanced recurrent and metastatic HNSCC cases. The comparative analysis of the data in the group with NLR<2 and NLR≥6 highlights an advantage of 4.4 months in median OS in favor of the group with low values of NLR. Being cheap and accessible, these markers could change the therapeutic approach even in centers with limited resources. The role of borderline NLR values as a prognostic factor in HNSCC must also be defined. PLR and MLR are less evaluated as biomarkers but the study demonstrates their potential to be used as prognostic biomarkers, it remains to be clarified if their inclusion in multivariable models along with NLR would bring a benefit

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

Cutaneous melanoma (CM) is a candidate for screening programs, since its prognosis is excellent when diagnosed in an early disease stage. Targeted screening of those at high risk for developing CM, a cost-effective alternative to population-wide screening, requires valid procedures to identify the high-risk group. Self-assessment of the number of nevi has been suggested as a component of such procedures, but its validity has not yet been established. We analyzed the level of agreement between self-assessments and expert assessments of the number of melanocytic nevi in the area between the wrist and the shoulder of both arms based on 4548 study subjects in whom mutually blinded double counting of nevi was performed. Nevus counting followed the IARC protocol. Study subjects received written instructions, photographs, a mirror, and a “nevometer” to support self-assessment of nevi larger than 2 mm. Nevus counts were categorized based on the quintiles of the distribution into five levels defining a nevus score. Cohen’s weighted kappa-coefficient was estimated to measure the level of agreement. In the total sample, agreement between self-assessments and expert-assessments was moderate (raw agreement: 50.29%, weighted κ=0.596). Self-assessed nevus counts were higher than those determined by experts (mean differ-ence: 3.33 nevi). The level of agreement was independent of sociodemographic and cutaneous factors; however, participants’ eye color had a significant impact on the level of agreement. Our findings show that even with comprehensive guidance, only a moderate level of agreement between self-assessed and expert-assessed nevus counts can be achieved. Self-assessed nevus information does not appear to be reliable enough to be used in individual risk assessment to target screening activities.

The concept of {\it quantum ratio} emerged in the recent efforts to understand how Newton's equations appear for the center of mass (CM) of an isolated macroscopic body at finite body-temperatures, as the first approximation to quantum-mechanical equations. It is defined as $Q\equiv R_q/L_0$, where the quantum fluctuation range $R_q$ is the spatial extension of the pure-state CM wave function, whereas $L_0$ stands for the body's linear size (the space support of the internal, bound-state wave function). The two cases $R_q /L_0 \lesssim 1$ or $R_q/ L_0 \gg 1$, roughly correspond to the body's CM behaving classically or quantum mechanically, respectively. In the present note we elaborate more on this concept, illustrating it in several examples. An important notion following from introduction of the quantum ratio is that the elementary particles (thus the electron and the photon) are quantum mechanical, even when the environment-induced decoherence turns them into a mixed state. Decoherence and classical state should not be identified. This simple observation, further illustrationed by the consideration of a few atomic or molecular processes, may have significant implications on the way quantum mechanics works in biological systems.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Background: Metabolic flux analysis (MFA) is an indispensable tool in metabolic engineering. The simplest variant of MFA relies on an overdetermined stoichiometric model of the cell’s metabolism under the pseudo-steady state assumption, to evaluate the intracellular flux distribution. Despite its long history, the issue of model error in the overdetermined MFA, particularly misspecifications of the stoichiometric matrix, has not received much attention. Method: We evaluated the performance of statistical tests from linear least square regressions, namely Ramsey RESET test, F-test and Lagrange multiplier test, in detecting model misspecifications in the overdetermined MFA, particularly missing reactions. We further proposed an iterative procedure using the F-test to correct such an issue. Result: Using Chinese hamster ovary and random metabolic networks, we demonstrated that: (1) a statistically significant regression does not guarantee high accuracy of the flux estimates, (2) the removal of a reaction with a low flux magnitude can cause disproportionately large biases in the flux estimates, (3) the F-test could efficiently detect missing reactions, and (4) the proposed iterative procedure could robustly resolve the omission of reactions. Conclusion: Our work demonstrated that statistical analysis and tests could be used to systematically assess, detect and resolve model misspecifications in the overdetermined MFA.

Understanding surface water evaporation in tropical catchments is pivotal for effective water management, but limited research exists on stable isotopic (δ2H and δ18O) assessment of water evaporation losses. Our study bridges that gap, examining stable isotopes in meteoric water and surface waters across tropical regions, both humid and semi-arid. Using the Craig-Gordon model, we calibrated evaporation-to-inflow (E/I) ratios, identifying distinct E/I variations between seasons and regions. Notably, the semi-arid region consistently exhibited higher E/I ratios due to climatic characteristics. By integrating the Hamiltonian Monte Carlo and the No-U-Turn Sampler, we were able to quantify uncertainties in isotopic and meteorological parameters, resulting in E/I estimates within 68% and 95% confidence intervals. Our Bayesian model insights are critical for freshwater resource optimization and hydrological modeling in tropical regions.

Acoustic Radiation Forced Impulse (ARFI) is an ultrasound integrated method, measuring stiff-ness by point shear wave elastography. To evaluate the diagnostic performance of ARFI of the liver and of the spleen, combined with spleen dimension and platelet count, in predicting clinical events in cirrhosis, a prospective and cross-sectional study was conducted between February 2017 and February 2021. The following ratio scores with ARFI measurements were performed: ALSDP (ARFI Liver-Spleen Diameter-to-Platelets ratio score), ASSDP (ARFI Spleen-Spleen Diam-eter-to-Platelets ratio score), ASSAP (ARFI Spleen-Spleen Area-to-Platelets ratio score), ALSAP (ARFI Liver-Spleen Area-to-Platelets ratio score). In 100 enrolled subjects, spleen ARFI, ASSDP, ASSAP, were significantly associated with high-risk oesophageal varices (HRVs) in the prospec-tive short- and long-term follow-up and in the cross-sectional study (p 0.7). ARFI-ratio scores can predict, in cirrhotic patients, the risk of developing HVRs in short and long-term period.

Background: Psoriasis is a chronic immune-mediated skin disease in which systemic inflammation plays an important role in the pathogenesis. In recent years, neutrophil-to-lymphocyte ratio (NLR), neutrophil-to-monocyte ratio (NMR), platelet-to-lymphocyte ratio (PLR), and systemic immune-inflammation index (SII) have been shown to be important indicators of inflammation. In this study, our aim is to investigate NLR, NMR, PLR, and SII levels in psoriasis patients treated with biologic agents. Method: Clinical and biochemical data of 209 patients who received systemic therapy for psoriasis were obtained by retrospectively reviewing their medical records. NLR, NMR, PLR, and SII values were calculated from the hemogram values of the patients. Results: In the third month of follow-up, the mean CRP, NLR, NMR, PLR, and SII values were significantly decreased compared to the baseline values. SII values showed strong positive correlations with NLR, NMR and PLR. Adalimumab, etanercept, and infliximab, which are TNF-α blockers, were observed to be more effective on PLR and NLR and especially NMR. Conclusion: NLR, NMR, PLR, and SII, which are data obtained from routine blood tests, can be used in the monitoring of treatment of psoriasis, especially with TNF- α blockers.

Combining the Job Demands-Resourses model and the Work Adjustment theory, this research aims to create a theoretical model that considers Leader-Member Exchange (LMX) and Work Adjustment as protective factors, capable of reducing job exhaustion and turnover intention. A convenience sample of 257 Italian employees filled an online self-report questionnaire. A sequential mediation model was tested, which showed that the relationship between LMX and turnover intention is mediated by Work Adjustment and Job Exhaustion. The results show that the higher the LMX, the higher the work adjustment of the workers and the less they will perceive job exhaustion and, consequently, intent to leave the organisation. With a view to primary prevention, the aim was to investigate possible protective factors at work and the risk factors to look out for in order to move in the direction of preventing a malaise phenomenon before it develops with the aim of promoting wellbeing in organisations.

With covid infection having a periodic occurrence and each wave affecting millions of people, there is an urgent need for healthcare providers to develop readily available biological markers to predict the severity and mortality of COVID-19 infection at an early stage of the disease to predict the most optimal management. The Neutrophil – lymphocyte Ratio (NLR) and Platelet-lymphocyte ratio (PLR), are novel inflammatory markers suggested to predict the severity of illness in COVID -19 patients. We evaluated a retrospective cohort of 224 patients with covid 19 illnesses from August 2020 to October 2020. We categorized the patients into 'mild' and 'moderate to severe as per the severity of their illnesses. The optimal cut-off values of the continuous NLR, PLR, and Age were calculated by applying the receiver operating characteristic (ROC) curve analysis. Sensitivity, specificity, and likelihood ratios were calculated from ROC analysis. The results showed that Age, Hb, and NLR are significant predictors of the severity of illness. So we quantified the predictive contribution of those variables by its Z- score and showed that NLR is the strongest predictor followed by Age.ROC curve analysis revealed NLR to be an excellent predictor of disease severity (sensitivity 88.30% and specificity 82.60%) at a cut-off of > 4.24. A cut-off of 165.63 was obtained for PLR, which showed good predictive value for the severity of illness. A NLR > 6 was used as a predictor for mortality due to covid illness with good sensitivity and specificity. Conclusion: NLR and PLR can be used as prognostic markers to identify the severity of covid illness and the probability of mortality in the future in low-resource settings. Given its low cost, easily available, accessible, and reproducible data, it can be used as a useful marker to assist the physician in early referral and treatment of covid 19 infected patients.

The golden ratio, also known as Phi (ϕ ≈ 1.618034), attracted the interest of mathematicians, artists, and intellectuals for many centuries, probably from when it was discovered in human anthropometry. Even in recent times, researchers found the presence of golden ratio in Renaissance paintings and aesthetic preferences. The reasons behind the fascination with the golden ratio remain unclear, but it has been suggested that stimuli containing this proportion are often perceived as beautiful. However, evidence is conflicting, and the literature struggles to establish the existence of individual preferences for golden ratio. To gain new insights into the nature of these preferences, one hundred participants completed an implicit association task, with either golden ratio or random stimuli presented with positive or negative words. Participants initially categorized the stimuli based on their assigned categories. Then, we assessed their explicit preferences by asking to rate the stimuli in terms of pleasantness and by completing a line bisection task and the Ultimate Game. The results revealed the typical effects observed in implicit association tasks, with improved response times and accuracy when golden ratio stimuli were associated with positive word categories. In contrast, explicit ratings yielded mixed results. We discuss our findings in relation to previous studies that have explored this issue, highlighting the ongoing debate surrounding preferences for the golden ratio.

Day-ahead forecasting of electricity prices is important in deregulated electricity markets for all the stakeholders: energy wholesalers, traders, retailers, and consumers. Electricity price forecasting is an inherently difficult problem due to its special characteristic of dynamicity and non-stationarity. In this paper, we present a robust price forecasting mechanism that shows resilience towards aggregate demand response effect and provides highly accurate forecasted electricity prices to the stakeholders in a dynamic environment. We employ an ensemble prediction model in which a group of different algorithms participate in predicting the price for each hour of a day. We propose two different strategies, namely, Fixed Weight Method (FWM) and Varying Weight Method (VWM), for selecting each hour's expert algorithm from the set of participating algorithms. In addition, we utilize a carefully engineered set of features selected from a pool of features derived from information such as past electricity price data, weather data, and calendar data. The proposed ensemble model offers better results than both the Pattern Sequence-based Forecasting (PSF) method and our own previous work using Artificial Neural Networks (ANN) alone do on the datasets for New York, Australian, and Spanish electricity markets.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

This study addresses the implementation of the International Financial Reporting Standard 9 (IFRS 9) in the European Union as of January 1, 2018, replacing the International Accounting Standard 39 (IAS 39) to introduce a new model for recognizing Loan Loss Provisions (LLP) based on Expected Credit Loss (ECL). This model responds to criticisms of the former Incurred Credit Loss (ICL) system for its inability to reflect credit losses in a timely manner, potentially exacerbating the effects of financial crises (Bushman &amp; Williams, 2015; Gebhardt &amp; Novotny-Farkas, 2011). The study focuses on the effects of adopting the ECL model on the level of Loan Loss Allowances (LLA) in loans, own equity, and the Common Equity Tier 1 (CET1) ratio across 13 Portuguese commercial banks. A mean comparison test is used to evaluate scenarios before and after the application of the ECL model, highlighting the importance of regulator actions and the adequacy of loss recognition policies, including the effects of Regulation (EU) 2017/2395 of December 12. The results obtained demonstrate significant negative impacts on the net values of loans, own equity, and the CET1 ratio upon adopting the IFRS 9 ECL model, due to the widespread increase in LLAs.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

Background: Since the previous study dealing with the case fatality ratio and infection fatality ratio caused by COVID-19, the author has received many comments that prompted the question: "Why did an optimistic prognosis fail?" To answer this question, a more detailed and expanded analysis was carried out in a new study. Objective: To evaluate the dynamics of monthly numbers of cases, deaths, tests and CFR worldwide during three phases of the COVID-19 pandemic. Material and Methods: Twenty three sets of databases, dated the 22nd of each month from January 2020 to November 2021, for 213 countries were collected from the Worldometer website. The number of cases, deaths, tests, CFR, IFR, etc. were counted for various periods of time for each of the 213 countries, then results related to different periods of time were compared. Results: The analysis of the main epidemiological parameters led to the division of three phases of the global pandemic evolution. The first phase (23.01.20-22.07.20), the second phase (23.07.20-22.01.21) and the third phase (23.01.21-22.07.21) were different in terms of the number of tests performed, new cases, and mortality due to COVID-19. By the end of the second phase, the worldwide statistics indicated the imminent end of the pandemic, but the third phase was characterized by a sudden rise in the number of new cases and deaths that could not be explained rationally. The most dramatic evolution of the epidemic curve occurred in the countries where doctors had successfully battled COVID-19 during the first two phases of the pandemic. Conclusions: Despite the decrease in overall death numbers during the latest months analyzed, additional study is necessary to identify the cause for the increase in the number of new cases and deaths during the third phase of the pandemic. Only complete information regarding the positive and negative impact of medical and non-medical methods of diagnostics and prophylaxis of COVID-19 can help to organize effective measures to end the current pandemic and prevent a similar one from occurring in the future. Presumably, there are several causes of the negative evolution of the current pandemic, including the overreliance on PCR tests, application of non-specialized premises for quarantine and treatment, decrease in herd and individual immunity, inadequate change of therapeutic protocols, and ignoring prophylactic treatment. It can be suggested that the use of immunemodulatory drugs, for example, thymus extract or thymic peptides, in groups of people with compromised immunity is necessary, and prophylactic and therapeutic protocols should be changed from the 'standard' types to 'personalized' ones.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

Periodontitis is a chronic inflammatory disease which results in the destruction of the tooth’ s supporting tissues and the alveolar bone resorption. The complement becomes a major link between infection and inflammatory pathology including periodontitis. Gingipians as important virulence factors of P. gingivalis have the activity of C5 convertase, could cleave C5 into fully functional C5a to activate C5aR. The above process could be blocked by the C5aR antagonist (PMX-53) to suppress local periodontal inflammation, and then achieves the purpose of treatment of periodontitis. Nanoparticles incorporated within gelatin are promising carrier system for drug delivery in recent years. This study aimed to investigate whether gelatin nanoparticles loaded with PMX-53 prevents alveolar bone resorption in miniature swines model of periodontitis. Four miniature swines were placed ligatures around the maxillary and mandibular fourth premolar and first molar on both sides for seven weeks to induce periodontitis. Then, animals were assigned randomly to four groups: minocycline-treated group, gelatin with PMX53-treated group, gelatin-treated group and a sham control group. They were treated with 1ml related drugs respectively, into gingival sulcusl for 4 times at one-week intervals. We showed that local treatments with gelatin nanoparticles loaded with PMX-53 could inhibit alveolar bone loss of periodontitis. Our study revealed that gelatin nanoparticles loaded with PMX-53 prevented alveolar bone resorption miniature swines model of periodontitis. In addition, provided proof-of-concept for local targeting of gelatin nanoparticles loaded with PMX-53 as a powerful candidate for the treatment of periodontitis.

In this work model of mirror elements equilibrium of the micromechanical components is developed, the behavior analysis of the mirror element of micromechanical mirrors in case changing of control voltages of electrostatic actuators is carried out, an expression for determining the maximum value of deflection voltage at which the snap-down effect will take the following form is obtained in case of the influence of the coefficient of the electrostatic rigidity of electrostatic actuators. The developed equilibrium model of mirror elements and the obtained results of modeling can be used at design of micromechanical mirrors with internal suspensions.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Weak interaction processes continue to be hot topics in fundamental physics research. In this paper, we briefly review some recent advances in the theoretical study of beta and double-beta decays that include both the nuclear and atomic part of these processes. On the nuclear side, we present a statistical approach for the computation of the nuclear matrix elements (NME) for neutrinoless double-beta (0νββ). A range of NME values, the most probable value for NME, and the associated theoretical uncertainty are given. Correlations with other related observables are shown as well. On the atomic side, we first briefly review the methods used to get the electrons’ wave functions. Further, we use them for the computation of some relevant kinematic quantities such as Fermi functions, electron spectra and angular correlation between the emitted electrons. Then, we present applications of these calculations to the experimental data analysis related to the search of the Lorentz invariance violation in two-neutrino double-beta (2νββ) decay and description of the decay rates and decay rate ratios for allowed and unique forbidden electron capture (EC) processes.

The article shows materials to the question about algebraic features of the genetic code and about the dictatorial influence of the DNA and RNA molecules on the whole organism. Presented results testify in favor that the genetic code is an algebraic code related with a wide class of algebraic codes, which are a basis of noise-immune coding of information in communication technologies. Structural features of the genetic systems are associated with hypercomplex double (or hyperbolic) numbers and with bisymmetric doubly stochastic matrices. The received results confirm that represented matrix approaches are effective for modeling genetic phenomena and revealing the interconnections of structures of biological bodies at various levels of their organization. This allows one to think that living organisms are algebraically encoded entities where structures of genetic molecules have the dictatorial influence on inherited structures of the whole organism. New described algebraic approaches and results are discussed.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

Despite notable advancements in immunotherapy in the past decades, allogeneic hematopoietic stem cell transplantation (allo-HCT) remains a promising, potentially curative treatment modality. Only a limited number of studies has performed a direct comparison of two prevalent rabbit anti-thymocyte globulin (r-ATG) formulations — specifically, Thymoglobuline (ATG-T, formerly Genzyme) and Grafalon (ATG-G, formerly Fresenius). The primary objective of our retrospective analysis was to compare the outcomes of adult patients undergoing matched or mismatched unrelated donor (MUD/MMUD) allo-HCT, with a graft-versus-host disease (GvHD) prophylaxis based on either ATG-T or ATG-G. A total of 87 patients undergone allo-HCT between 2012 and 2022 were included. We observed no significant differences between ATG-T and ATG-G concerning the occurrence of acute graft-versus-host disease (aGvHD), regardless of its severity. Conversely, chronic graft-versus-host disease (cGvHD) occurred less frequently in the ATG-T group compared to ATG-G (7.5% vs. 38.3%, p=0.001). Patients treated with ATG-T manifested a higher incidence of cytomegalovirus (CMV) reactivations (70% vs. 31.9%, p&lt;0.001), with a shorter time between transplant and CMV (&lt;61 days, 77.8% vs. 33.3%, p=0.008) and a higher median CMV copy number (1000 vs. 0, p=0.004). Notably, despite a higher occurrence of CMV reactivations in the ATG-T cohort, most patients were asymptomatic compared to ATG-G (85.7% vs. 43.8%, p=0.005). Finally, we observed no significant differences in terms of 5-year overall survival (OS) and 3-year probability of relapse while comparing ATG-T and ATG-G (32.0% vs 40.3%, p=0.423; 63.9% vs 55.7%, p=0.438, respectively).

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

Smart manufacturing encompasses a category of manufacturing that employs computer-integrated capabilities and technologies to enhance supply chain optimization, production efficiency, and recyclability. Yet limited studies have been conducted to optimize these prospects from the perspective of low resource countries where such innovative studies have not been adequately explored. This paper aims to examine the implications of smart manufacturing practices (Smart Procurement, Smart Supply Chain, Smart Production Planning and Control, Automation and Industrial Robot, and Supply Chain Configuration) on pro-environmental behaviour and develop a baseline moderated mediation model to explain the relationship between smart manufacturing and pro-environmental behaviour with a role of green dynamic capability, and environmental orientation. This study is anchored on quantitative research approach, deductive reasoning, and explanatory design. Cross – sectional survey data have been obtained from 382 manufacturing companies in Ghana. Our hypotheses have been tested using Structural Equation Modelling and SMART-PLS version 3.8.9. The study has revealed that smart manufacturing practices significantly and positively relate to pro-environmental behaviour. Moreover, green dynamic capability and environmental orientation moderate the relationship between smart manufacturing and pro-environmental behaviour. The implications of the study include the emergence of a baseline model to guide policymakers, practitioners, and academicians to explain the relationship between smart manufacturing and sustainable manufacturing in the context of developing countries. Again, the social implication of the study includes the realisation of decent job and economic growth, responsible consumption and production as well as actions taken to combat climate change.

A comprehensive kinetic model of the Fischer-Tropsch synthesis (FTS) is developed in a fixed bed reactor under operating conditions (temperature, 230–235°C, pressure, 20–25 bar, gas hourly space velocity, 4000–5000 cm³(STP)/h/g_catalyst ,H₂/CO feed molar ratio, 2.1) over a Co based catalyst. Reaction rate equations based on Eley-Rideal (ER) type model for initiation step and Langmuir-Hinshelwood-Hougen-Watson (LHHW) type model for propagation and termination steps of the FTS reactions have been considered and the readsorption of olefins were taken into account. The model that was reported in the literature was modified in order to explain many significant deviations from the ASF distribution. Optimum parameters have been obtained by Genetic Algorithms (GA). The calculated activation energies to produce n-paraffins and 1-olefins were in the range of 82.24 to 90.68 kJ/mol and 100.66 to 105.24 kJ/mol, respectively. The hydrocarbon distribution in FTS reactions was satisfactorily predicted particularly for paraffins.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

We start out by deriving simple analytic expressions for all measurable amounts of cases and fatalities during a pandemic evolution exhibiting multiple waves, described by the semi-time SIR model. The approximant shares all relevant features with the exact solution, including time and position of the peak of daily new infections, as well as the asymptotic behaviors at small and large times. We derive exact analytic expressions for the early doubling time, late half decay time, and a half-early peak law, characterizing the dynamical evolution. We show, in particular, how the asymmetry of the first epidemic wave and its exponential tails are affected by the initial conditions; a feature that has no analogue in the all-time SIR model. We apply the approach to available data from different continents. Our analysis reveals that the immunity is very strongly increasing during the 2nd wave, while it was still at a very moderate level of a few percent in several countries at the end of the first wave. The wave-specific SIR parameters describing the infection and recovery rates we find to behave in a similar fashion, while their ratio k was decreasing only by a about 5% for most countries. Still, an apparently moderate change of k can have significant consequences for the relevant numbers like the final amount of infected or deceased population. As we show, the probability for an additional wave is however low in several countries due to the fraction of immune inhabitants at the end of the 2nd wave, irrespective the currently ongoing vaccination efforts. We compare with alternate approaches.

This paper aims to develop a hierarchical risk assessment model using the newly-developed evidential reasoning (ER) rule, which constitutes a generic conjunctive probabilistic reasoning process. In this paper, we first provide a brief introduction to the basics of the ER rule and emphasize the strengths for representing and aggregating uncertain information from multiple experts and sources. Further, we discuss the key steps of developing the hierarchical risk assessment framework systematically, including (1) formulation of risk assessment hierarchy, (2) representation of both qualitative and quantitative information, (3) elicitation of attribute weights and information reliabilities, (4) aggregation of assessment information using the ER rule and (5) quantification and ranking of risks using utility-based transformation. The proposed hierarchical risk assessment framework can potentially be implemented to various complex and uncertain systems. A case study on the fire/explosion risk assessment of marine vessels demonstrates the applicability of the proposed risk assessment model.

In current transportation hubs, it is a common phenomenon that passengers travel with necessary wheeled-luggage or suitcases. Due to the fact that most luggage occupies certain space within dense passenger crowds with giant mass inertia, its abnormal motions, such as drifting, frequently trig unavoidable local disturbances and turbulence in surrounding pedestrian flows, further increasing security risk. While, current researches primarily concentrate on examining the impact of luggage on crowd evacuation efficiency through scenario-based experiments and analyzing the spatial characteristics of crowd distribution in surveillance videos. There still lacks of the dynamic disturbance mechanisms and crowd stability associated with the combined motion of passengers and luggage. Therefore, this study considers the luggage-laden passenger as a deformable particle, the resulting disturbance on surrounding non-luggage passengers is analyzed and quantified into a nonlinear pressure term. Subsequently, the disturbance propagation model of passenger-luggage is developed by adapting the classical Aw-Rascle traffic flow model with incorporation of the pressure term. Simulation experiments of disturbances caused by luggage drifting and retrograding validate that the proposed propagation model aligns with real-world situations in transportation hubs. Quantitively, when luggage-laden passenger drifted left, the disturbing force of left side crowd can reach a peak of 238N in the passenger density of 3.0 p/m2, and the maximum difference between the left and right sides disturbing force can reach 153N. Furthermore, it is recommended that the proposed model can be applied to crowd flow analysis and risk assessment.

Antioxidant, anti-inflammatory and chemo-preventive features have been reported for the carotenoid diatoxanthin. Diatoxanthin is only produced by a few groups of microalgae where it functions in photoprotection. Its large-scale production in microalgae is currently not feasible. In fact, rapid conversion into the inactive pigment diadinoxanthin is triggered when the cells are removed from the high-intensity light source, which will be the case during large-scale harvesting of microalgae biomass. Zeaxanthin epoxidase (ZEP) 2 and/or ZEP3 have been suggested to be responsible for the back-conversion of high-light accumulated diatoxanthin to diadinoxanthin in low light in diatoms. Using the CRISPR/Cas9 gene editing technology we knocked out the ZEP2 and ZEP3 genes in the already commercially used marine diatom Phaeodactylum tricornutum to investigate their role in the diadinoxanthin-diatoxanthin cycle, and to determine if one of the mutant strains could function as a diatoxanthin production line. Light shift experiments proved that ZEP3 encodes the enzyme converting diatoxanthin to diadinoxanthin in low light. Loss of ZEP3 caused the high-light accumulated diatoxanthin to be stable for several hours after the cultures had been returned to low light, suggesting that zep3 mutant strains could be suitable as commercial production lines of diatoxanthin.

The organic fraction of municipal solid waste (OFMSW) is a significant environmental threat, and an economic and social challenge to manage. As such, the efficient treatment of OFMSW is a significant key factor in achieving sustainable waste management. Decentralized Composting (DC) develops a new framework of waste management. The DC Analysis Model (DCAM), proposed in our previous study, provides a powerful tool for decision makers, based on the quantification of the DC project characteristics. In this paper, we focus on the qualitative analysis as a complementary tool to support decision making, in cases where quantitative analysis is unequivocal. The qualitative analysis identifies the main players in the field, the critical stakeholders and the potential conflicts between them. It also reveals the root problems and the core competencies for the project's implementation. DCAM qualitative analysis in Shefa-Amr (case study) indicates that unresolved root problems, such as the “lack of national regulation”, “clear ownership of the project” and “lack of ongoing budget” can result in an unsustainable composting system. Countering that, “the commitment of the municipality”, together with “economic viability” and securing “suitable areas for placing composters” are among the most important core competencies for the effective implementation of DC projects.

Based on the definition of double fuzzy relations, two types of new rough set models are constructed, which are multi-granulation double fuzzy rough sets called optimistic and pessimistic multi-granulation double fuzzy rough sets, and some of their properties were studied. In addition, we study the relationship between optimistic and pessimistic multi-granulation double fuzzy rough sets and double fuzzy rough sets.

Gestational diabetes mellitus (GDM) pathophysiology comprises clinical and genetic factors. In fact, GDM has been associated with several single nucleotide polymorphisms (SNPs). This study aimed to build a prediction model of GDM combining clinical and genetic risk factors. A total of 1588 pregnant women from the San Carlos Cohort participated in the present study, 1069 (67.3%) Caucasian (CAU) and 519 (32.7%) Latin American (LAT), 255 (16.1%) with GDM. The incidence of GDM was similar in both groups (16.1% CAU and 16.0% LAT). Genotyping was performed by IPLEX Mass ARRAY PCR selecting 110 SNPs based on literature references. The SNPs showing the strongest likelihood of GDM development were the rs10830963, rs7651090 and rs1371614 in CAU and rs1387153 and the rs9368222 in LAT. Clinical variables including age, pre-pregnancy body mass index and fasting plasma glucose (FPG) at 12 gestational weeks predicted the risk of GDM (AUC 0.648, 95%CI 0.601-0.695 in CAU; AUC 0.688, 95%CI 0.628-9.748 in LAT) and adding the SNPs modestly improved prediction (AUC 0.722, 95%CI 0.680-0.764 in CAU; AUC 0.769, 95%CI 0.711-0.826 in LAT). In conclusion, adding genetic variants enhanced the prediction model of GDM risk in CAU and LAT pregnant women. An RCT is underway to demonstrate its usefulness

The hump feature is one of the major instabilities in pump-turbines. When pump-turbines operate in the hump region, strong noise and serious fluctuations can be observed, which are harmful to their safe and stable operation and can even destroy the whole unit as well as water conveyance system. In this paper, a low specific speed (n_q = 36.1 min⁻¹) pump-turbine model was experimentally investigated. Firstly, the hump characteristic was obtained under 19 mm guide vane opening conditions. More interestingly, when the hump characteristic was measured in two directions (increasing and decreasing the discharge), characteristic hysteresis was found in the hump region. The analysis of performance characteristics reveals that the hump instability is the result of Euler momentum and hydraulic losses, and different Euler momentum and hydraulic losses in the two development processes lead to the hysteresis phenomenon. Then, 12 pressure sensors were mounted in the different parts of the pump-turbine model to obtain the time and frequency characteristics. The analysis of the corresponding fast Fourier transform confirms that the hump characteristic is related to low-frequency (0.04–0.15 times rotational frequency) vortices. The occurrence and cessation of vortices depend on the operating condition and measurement direction, which contribute to the hysteresis feature. Finally, the type of the low-frequency vortices was analyzed through the cross power spectrum.

Analysing the human body by direct observation can lead to misinterpretation of underlying trends, whereas in vitro organ models facilitate their understanding. Likewise, in vitro organ models serve as valuable tools for assessing the toxicity of compounds. However, none of the existing models had the features we considered critical for toxicity assessment, so we developed an in vitro liver model for toxicity assessment. We used four different types of primary liver cells: Hepatic sinusoidal endothelial cells, hepatic stellate cells, Kupffer cells and hepatocytes. We cultured them in different combinations of composition and volume of cell medium, hepatocyte proportion of total cells, and addition of extracellular matrix. We added rifampicin, ibuprofen and 5-fluorouracil to this model and observed the microanatomy and physiology changes for a week with preclinical and clinical instruments. Among the different model configurations, we selected the feature combination of the in vitro model that had similar biomarker values to those measured by the clinical instruments used in clinical diagnostics. When we exposed the selected model configuration to rifampicin, ibuprofen and 5-fluorouracil, the viability of Kupffer cells and liver sinusoidal endothelial cells was significantly lower than in the untreated samples. In contrast, we observed negligible viability of hepatocytes compared to the untreated samples. We have built an in vitro liver model that resembles the liver microenvironment and we have analysed it with clinical instrumentation to facilitate the data translation. In this sense, we have established that Kupffer and LSEC cells are suitable candidates for the search for clinical diagnostic markers of liver function.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

: Inflammation may mediate the association of mitral valve prolapse (MVP) with ventricular scarring and arrhythmia. The purpose of this study is to investigate the association of neutrophil- and platelet-to-lymphocyte ratios (NLR, PLR) with ventricular arrhythmia in MVP. Clinical and demographic data were extracted from electronic medical records for all patients aged 18-90 years with MVP on echocardiography between 2016-19 at our institution. We studied 65 patients who had a differential blood count within six months prior to ambulatory ECG (A- ECG) (medi-an age [IQR] 70 [61-77] years; 62% female; 12% African American). Patients with surgery or in-fection within six months prior to CBC were excluded. Complex or frequent ventricular ectopy (cfVE) was defined as the presence of two or more premature ventricular contractions (PVCs) on a 10-second ECG tracing or greater than 1% PVC burden or NSVT on ambulatory ECG monitoring. Logistic and bivariate regression was used to analyze clinical, electrocardiographic and echo-cardiographic factors associated with NLR and PLR. Factors associated with higher NLR were congestive heart failure (p=0.005), male sex (p=0.01), age (p=0.003), and bileaflet MVP (p=0.04). NLR was associated with higher absolute PVC burden (rs=0.28, p=0.03) and cfVE (median NLR [IQR] 3.0 [1.6 – 6.3]) with cfVE versus (2.4 [1.4-3.4], p=0.04) without cfVE. An NLR of 5.6 yielded 50% sensitivity and 90% specificity for PVC burden >1% (AUC 0.69). No significant association was found between PLR and PVC burden or cfVE. NLR is associated with PVC burden and com-plex ventricular ectopy in MVP, suggesting that inflammation is a significant factor in the patho-genesis of ventricular arrhythmia in this condition.

The prevalence and incidence of cardiac pro-arrhythmic disorders are often influenced by sex due to specific effects on the QT interval. Androgens shorten QT, which may be protective against acquired long QT syndromes and their related arrhythmias in men such as torsade de pointes (TdP). On the other hand, androgens can potentiate Brugada and early repolarization syndromes, which are most prevalent in men. In this case series, we highlight four male patients with aborted SCD in the setting of abnormal testosterone status; two patients with TdP in a setting of testosterone deprivation (of which one drug-induced) and 2 patients with ventricular fibrillation associated with exogenous androgenic booster (Tribulus terrestris) intake. From this case series, we review the current available literature of the effects of androgen as a double-edged sword on the QTc interval and emphasize the importance of QTc monitoring in this subset of patients.

In the present paper we investigate the conservative conditions in Quadratic Gravity. It is shown explicitly that the Bianchi identities lead to the conservative condition of the left-hand-side of the (gravitational) field equation. Therefore, the total energy-momentum tensor is conservative in the bulk (like in General Relativity). However, in Quadratic Gravity it is possible to have singular hupersurfaces separating the bulk regions with different behavior of the matter energy-momentum tensor or different vacua. They require special consideration. We derived the conservative conditions on such singular hypersurfaces and demonstrated the very possibility of the matter creation. In the remaining part of the paper we considered some applications illustrating the obtained results.

Accurate diagnosis for the 400 million people with rare diseases is critical for healthcare decisions, prognosis, understanding disease mechanisms, and identification of treatments. Despite advances in genome sequencing, barriers such as high interpretation costs, diagnostic expertise, throughput associated delays, and uncertain variant classifications persist, with demand exceeding capacity. Many variant classification methods focus narrowly on specific consequences, leading to the use of complex integrative pipelines that often overlook transcript variability and lack prediction transparency. To overcome these limitations, we introduce DITTO. This transparent, transcript-aware machine-learning method demonstrates superior overall performance in accuracy, recall, and precision when compared to existing tools. DITTO is publicly available at https://github.com/uab-cgds-worthey/DITTO

The Imbalance Cost Pass-Through (ICPT) is a flexible component of the Incentive Regulation (IBR) that empowers power producers to adjust tariffs in response to variable fuel prices, thereby enhancing the economic resilience of electricity generation. However, the cost of electricity generation is significantly influenced by the volatility of commodity prices, including coal, gas and LNG. In Malaysia, the Energy Commission has conducted biannual reviews of fuel and other generation costs. Any cost savings or increases identified during these reviews will be passed on to customers in the form of rebates or surcharges. Due to that reason, this study proposes ICPT price forecasting for the electricity market in Peninsular Malaysia. The study aims to construct an ICPT-related baseline model for the peninsular generation data by employing three forecasting methods. The forecasting performance is analysed by a Mean Absolute Percentage Error (MAPE). In findings, the ARIMA method is one of the most accurate forecasting methods for fuel prices compared to the Moving Average (MA) and LSSVM methods. The observed price differences between the ARIMA and LSSVM models for ICPT are minimal. The ICPT price for July-December 2022 and January-June 2023 is MYR 0.21/ kWh for ARIMA and MYR 0.18/kWh for LSSVM, which are close to the actual TNB’s ICPT tariff. As for the forecasting, the ICPT price is expected to drop for the next announcement. The findings of this study may contribute to a positive impact on the sustainability of the energy sector in Malaysia.

Semi-continuous data are very common in the social science and economics. In this paper, a Bayesian variable selection procedure is developed to assess the influence of exogenous factors including observed and unobserved on the semi-continuous data. Our formulation is based on the two-part latent variable model with polytomous response. We consider two schemes for the penalties of regression coefficients and factor loadings: the Bayesian spike and slab bimodal prior and the Bayesian lasso prior. Within the Bayesian framework, we implement Markov Chains Monte Carlo sampling method to conduct posterior inference. To facilitate posterior sampling, we recast the logistic model in part one as the norm-like mixture model. Gibbs sampler is designed to draw observations from the posterior. Our empirical results show that with suitable hyper-parameters, the spike and slab bimodal method slightly outperforms the Bayesian lasso in the current analysis. Finally, a real example related to the China household finance survey is analyzed to illustrate the application of the methodology.. .

The paper examines the various uncertainties encountered in high-frequency trading (HFT) environments and delves into the multiple challenges faced by HFT firms in navigating the Dodd-Frank Wall Street Reform and Consumer Protection Act (referred to as the "Dodd-Frank Act"), particularly during the initial stages of its enactment. These challenges include the ambiguity surrounding the definition of HFT, the lack of clarity regarding regulatory requirements and boundaries, inconsistencies in enforcement resulting from deviations in understanding the content, and the absence of detailed descriptions of the Act’s provisions. These hurdles significantly impact not only the daily operations of HFT firms but also pose higher demands on their long-term strategic planning and risk management. Drawing upon the Data, Information, Knowledge, Wisdom, and Purpose (DIKWP) model, this study employs an innovative analytical framework. Through the comprehensive application of conceptual space, cognitive space, and semantic space, it provides a systematic methodology for identifying and analyzing the aforementioned issues. This approach not only aids firms in better comprehending and adhering to complex regulatory requirements but also enables them to explore new business opportunities and competitive advantages while ensuring compliance.

The novel coronavirus disease (COVID-19) pandemic has resulted in over 720 million confirmed cases and 7 million deaths worldwide, with insufficient treatment options. Innumerable efforts are being made around the world for faster identification of therapeutic agents to treat the deadly disease. Postacute sequelae of SARS-CoV-2 infection or COVID-19 (PASC), also called Long COVID, is still being understood and lacks treatment options as well. A growing list of drugs are being suggested by various in silico, in vitro and ex vivo models, however currently only two treatment options are widely used: the RNA-dependent RNA polymerase (RdRp) inhibitor remdesivir, and the main protease inhibitor nirmatrelvir in combination with ritonavir. Computational drug development tools and in silico studies involving molecular docking, molecular dynamics, entropy calculations and pharmacokinetics can be useful to identify new targets to treat COVID-19 and PASC, as shown in this work and our recent paper that identified alendronate as a promising candidate. We have now investigated all bisphosphonates which can bind competitively to nidovirus RdRp-associated nucleotidyl (NiRAN) transferase domain, and systematically down selected seven candidates (CHEMBL608526, CHEMBL196676, CHEMBL164344, CHEMBL4291724, CHEMBL4569308, CHEMBL387132, CHEMBL98211), two of which closely resemble the approved drugs minodronate and zoledronate. This work and our recent paper together provide an in silico mechanistic explanation for alendronate and zoledronate users having dramatically reduced odds of SARS-CoV-2 testing, COVID-19 diagnosis, and COVID-19-related hospitalizations, and indicate that similar observational studies with minodronate could be valuable.

The eyes serve as a window into underlying physical and cognitive processes. Although factors such as pupil size have been studied extensively, a less explored yet potentially informative aspect is blinking. Given its novelty, blink detection techniques are far less available compared to eye-tracking and pupil size estimation tools. In this work, we present a new unsupervised machine learning blink detection strategy using existing eye-tracking technology. The method is compared to two existing techniques. All three algorithms make use of eye aspect ratio values for blink detection. Accurate and rapid blink detection complements existing eye-tracking research and may provide a new informative index of physical and mental status.

The figures of merit of luminescence intensity ratio (LIR) thermometry for Er3+ in 40 different crystals and glasses have been calculated and compared. For calculations, the relevant data has been collected from the literature while the missing data were derived from available absorption and emission spectra. The calculated parameters include Judd-Ofelt parameters, refractive indexes, Slater integrals, spin-orbit coupling parameters, reduced matrix elements (RMEs), energy differences between emitting levels used for LIR, absolute and relative sensitivities. We found a slight variation of RMEs between hosts as a result of variations in values of Slater integrals and spin-orbit coupling parameters, and we calculated their average values over 40 hosts. The calculations showed that crystals perform better than glasses in Er3+ based thermometry, and we identified hosts that have large values of both absolute and relative sensitivity.

In public health literature the risk of death or disease associated with a dietary, environmental of behavioral factor is most commonly denoted by odds ratio (OR), hazard ratio (HR) or risk ratio (RR). The ratio indices have several desirable statistical properties. However, the most important question is whether there are some evolved innate norms of perception of risk that people use and what they are. We conducted a simple one question survey of 98 individuals with different age, sex, educational and professional backgrounds. The respondents were asked to judge the relative perceived risk of four different hypothetical habits for which data on the percentage of people affected by the disease with and without the habit was given. They were asked to rank the risks for the four habits. Results showed that the habits that had the highest difference between probability of acquiring the disease were ranked high on risk perception. The probability ratios did not affect risk perception significantly. Further age, sex, profession or formal training in statistics did not affect the response significantly. Even individuals that were formally trained to use OR and HR as risk indicators, preferred using probability differences over ratios for judging their own risk in the perceived context. This preliminary inquiry into intuitive statistical perception suggests that designing statistical indices based on people’s innate perception may be a better strategy than trying to train people to understand the indices designed by expert statisticians.

This paper considers estimating the ratio of two distributions with different parameters and common supports. We consider a Bayesian approach based on the Log--Huber loss function which is resistant to outliers and useful to find robust M-estimators. We propose two different types of Bayesian density ratio estimators and compare their performance in terms of Bayesian risk function with themselves as well as the usual plug-in density ratio estimators. Some applications such as classification and divergence function estimation are addressed.

Based on the elasticity theory, this paper deals with the static analysis of a cracked double beam system in presence of a Winkler medium. The double-beam system is also supposed to be constrained at both ends by elastically flexible springs, with transverse and rotational stiffness. Using a variational formulation, the static governing equations are derived and solved by using analytical and numerical approaches. In the first approach, the closed-form solutions for the displacements functions are obtained based on the Euler-Bernoulli beam theory. In the second approach, the Cell-Discretization Method (CDM) is performed, according to which the two beams are reduced to a set of rigid bars linked together by means of elastic constraints, where the bending stiffness of the bars is concentrated. The resulting stiffness matrix is easily deduced, and the governing equations of the static problem can be immediately solved. A comparative analysis is performed in order to verify the accuracy and validity of the proposed method. This study focuses on the effect of various parameters including the crack depth and position, boundary conditions, elastic medium and slenderness. The validity of the proposed analysis is confirmed by comparing the present results with those obtained from the other approach. In particular, the results obtained by closed-form solution and Cell-discretization method (CDM) are compared by Finite element method (FEM). Accuracy of the results has been evaluated by making comparisons with the results in literature and reported in bibliography. It is demonstrated that the proposed algorithm provides a simple and powerful tool in dealing with the static analysis of a double-beam system. Finally, some concluding remarks are made.

Discrete Double Hilbert Exponential sums along polynomials. This is preprint version (not peer reviewed) And we now check the proof of (ii) of Lemma 3.2 whether it is really true.

Layout estimation is a challenge of segmenting a cluttered room image into floor, walls and ceiling. We applied Double refinement network proved to be efficient in the depth estimation to generate heat maps for room key points and edges. Our method is the first not using encoder-decoder architecture for the room layout estimation. ResNet50 was utilized as a backbone for the network instead of VGG16 commonly used for the task, allowing the network to be more compact and faster. We designed a special layout score function and layout ranking algorithm for key points and edges output. Our method achieved the lowest pixel and corner errors on the LSUN data set. The input image resolution is 224*224.

The impact of the agriculture net carbon effect is crucial for climate change mitigation, yet research on this topic in China is currently insufficient. In this study, the carbon balance ratio (CBR) is used to characterise the net carbon effect of agriculture, and the spatial Durbin model and threshold regression model were used to empirically analyse the CBR with a sample of 30 provincial-level regions in China from 2004 to 2019. The aim was to investigate the mechanism of the influence of the land management scale (SCALE) of farming on the CBR. The results of the study indicate that national farming generally has a net sink effect, with large changes in interannual fluctuations; the expansion of SCALE has an obvious role in increasing sinks and reducing emissions, and has a positive spatial spillover effect on CBR, with significant spatial heterogeneity. Furthermore, as the SCALE expands, the direction of the influence of rural residents’ income and education level on CBR changes in the opposite direction, showing a significant non-linear relationship characteristic. However, in most areas, the SCALE threshold has not yet been reached, suggesting that the improvement in education levels can still offset the negative impact of economic income growth in the short term. The study recommends paying attention to the role of farmers’ human capital, changing production methods, and implementing carbon peaking and carbon neutrality goals to enhance the net sink effect of the farming industry, which would be achieved by increasing land management scale.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

Meningitis is a severe disease associated with death in children under five with highest rates of infections under age of one. Vaccines for Neisseria meningitides and Haemophilus influenza are used to prevent the main causative agents of meningitis. Administration of H. influenzae type b (Hib) vaccine is recommended at 2, 4 and 6 months with a booster dose at 18 months. N. meningitidis has two commercially available vaccines, the pure polysaccharide is recommended at 24 months meanwhile the protein-conjugated vaccines at 12 months. We sought in this study to examine if coadministering the vaccines for the two main meningitis causing bacteria might be synergistic as a preliminary step towards the possibility of shuffling immunization schedule. So, we coadministered Hib vaccine with commercially available vaccines either quadrate (ACWY) polysaccharide meningococcal (Men) or conjugated meningococcal (Nim) vaccines in Balb/C mice (n = 6/group) and compared to each vaccine administered separately and controls. Thirty-five days post immunization, we measured specific antibodies titers. Hib vaccine increased Men antibody titers significantly for serotypes Y and W. When Hib vaccine was coadministrated with Nim, antibody titer for Y, W and A significantly increased. For serotype C, there was no significant difference in antibody titers among immunized groups. As for effect of meningococcal vaccines on Hib, Men significantly increased Hib antibody titers while Nim had no effect. Collectively, our data suggested that coadministration of Hib and Men or Nim vaccines was safe and had synergistic effect on immune responses elicited to both vaccines. Further studies are needed before immunization schedule modifications. Such immunization schedule recommendation should provide better protection against this life-threatening disease in young children.

Local food has continued to become more popular in both the home and as featured ingredients in all segments of food service. Numerous studies have explored the motivating factors for consumer purchasing motivators. However, no known study has explored if there is a correlation between ego and intent to buy local foods. This study adopted a modified version of the Theory of Trying and surveyed a sample of 237 food service buying agents in South Carolina to examine their perceptions of buying local. Results suggest that ego is a predictor of trying to purchase local foods for restaurants. It was also found that the modified model is an acceptable model for predicting buyer intent. These findings support the majority of the studies looking at ego-centric behaviors with green purchases and could potentially help local food suppliers to better market their products to foodservice establishments. This study could also act as the foundation for future studies to explore the full extent of ego’s motivational effect on purchasing intentions in the food service industry.

This paper introduces extensions H4,p and X8,p of Horn’s double hypergeometric function H4 and Exton’s triple hypergeometric function X8, taking into account recent extensions of Euler’s beta function, hypergeometric function, and confluent hypergeometric function. Among the numerous extended hypergeometric functions, the primary rationale for choosing H4 and X8 is their comparable extension type. Next, we present various integral representations of Euler and Laplace type, Mellin and inverse Mellin transforms, Laguerre polynomial representation, transformation formulae and a recurrence relation for the extended functions. In particular, we provide a generating function for the X8,p and several bounding inequalities for the H4,p and X8,p.

ESG (Environmental, Social, and Governance) responsibility fulfillment increasingly affects enterprise valuation. Although researchers debate about the precise effects, the prevailing view suggests a linear relationship between ESG performance and enterprise value. This study introduces a novel ESG responsibility performance metric through the Regulated Intermediary Model to delve into this relationship within the Chinese context. Our findings reveal an inverted U-shaped relationship between ESG performance and enterprise value, with financing constraints having a significant moderating effect. These findings remain robust after employing instrumental variables to mitigate potential endogeneity. Heterogeneity analysis demonstrates that this inverted U-shaped relationship is particularly pronounced in non-polluting and non-state-owned enterprises. Moreover, a comparison between equity and debt financing mechanisms underscores that improved ESG performance is associated with lower cost of equity financing, thereby enhancing enterprise value. Financial institutions are encouraged to leverage innovative financial instruments to diversify enterprise financing channels and alleviate financing constraints of enterprises that fulfill their ESG responsibilities.

Nitrogen (N) strongly affects plant growth and metabolism. For shikonin biosynthesis, although the ammonium toxicity phenomenon has been reported, the effects of nitrogen on the shikonin synthesis remains obscure. In this study, we carried out four different concentrations of NH4+ treatments on Arnebia euchroma hairy roots (AEHR) to clarify the influence of NH4+ on the growth and shikonin accumulation in A. euchroma and the possible mechanism. The results showed that compared with the 0% NH4+ treatment (only nitrate as nitrogen source), 10% NH4+ treatment increased the fresh weight and the dry weight of AEHR, and promoted the synthesis of shikonins; 20% NH4+ treatment started to show the inhibition effects on growth and shikonin accumulation of AEHR and 30% NH4+ treatment exhibited the strongest inhibition effects. With increased percentage of NH4+, AEHRs became shorter and thicker with more branches. To further elucidate the mechanism, we analyzed the time-course of nitrogen assimilation, gene expression level of key enzymes involved in the shikonin biosynthesis pathway, and contents of various endogenous hormones under NH4+ toxicity condition. Results indicated that auxin and cytokinin might regulate the growth and architecture of AEHR under NH4+ toxicity, and jasmonate level was reduced along with the inhibition of shikonin biosynthesis. This first comprehensive investigation into the effects of ammonium/nitrate ratio on shikonin biosynthesis not only provided valuable data for optimizing the in vitro culture and shikonin production in A. euchroma, but also suggested potential fertilizer strategies for its cultivation.

The temporal evolution of pandemics described by the susceptible-infectious-recovered (SIR)-compartment model is sensitively determined by the time dependence of the infection (a(t)) and recovery (u(t)) rates regulating the transitions from the susceptible to the infected and from the infected to the recovered compartment, respectively. Here approximated SIR-solutions for different time dependencies of the infection and recovery rates are derived which are based on the adiabatic approximation assuming time-dependent ratios k(t)=u(t)/a(t) varying slowly in comparison to the typical time characteristics of the pandemic wave. For such slow variations the available analytical approximations from the KSSIR-model, valid for a stationary value of the ratio k, are used to insert a-posteriori the adopted time-dependent ratio of the two rates. Instead of investigating endless different combinations of the time dependencies of the two rates a(t) and u(t) a suitably parameterized reduced time dependence of the ratio k(tau) is adopted. Together with the definition of the reduced time this parameterized ratio k(tau) allows us to cover a great variety of different time dependencies of the infection and recovery rates. The agreement between the solutions from the adiabatic approximation in its four different studied variants and the exact numerical solutions of the SIR-equations is remarkably good providing strong confidence in the accuracy of the proposed adiabatic approximation.

The enhancement of early diagnosis of lung cancer is mandatory to improve prognosis. We observed the increase cancer stem cells (CSC) and circulating tumor cells (CTC) in blood of mice on d3 after Lewis lung carcinoma (LLC) cell implantation before disease symptom. Besides we have developed an approach to reprogramming immune cells by inhibiting the MAPK/ERK pathway through MEKi and the PD-1/PD-L1 immune checkpoint signaling pathway. We hypothesized that reprogramming of spleen CD8+ T-cells could also create a population of immune cells with high antitumor activity. We reprogrammed CD8+ T-cells derived from the spleen of C57BL/6 mice (rsCD8+T-cells). The rsCD8+T-cells were able to migrate to lung and were more resistant after the exhaustion in vitro in comparison with naïve sCD8+T-cells. In the orthotopic LLC model, the rsCD8+T-cells therapy increased the amount of proliferating CD8+ and CD4+ T-cells in blood and lung from mice. The amount of CSC decreased in the blood and lung of mice treated with rsCD8+ T-cells. A morphological study revealed a decrease in the number of metastases in lung tissue. The antitumor effects of rsCD8+T-cells are based on the activation of the host immune response by increasing the populations of CD8+ and CD4+ T-cells and apoptosis of CSCs.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

Background: Nowadays vital signs in clinics are electronically monitored excepted for urine output which still requires, manual recording, which is subject to human errors. We, in-vitro, assessed in this study the ability a novel electronic device to measure by a combination of two different methods, the real time flow-output, like urine output. Methods: Flow or urine output was measured by a combination technique of gravimetry using a dynamometer and capacitive sensing to improve precision. Data were obtained in 3 different situations, low, medium, and high flow. Results: Three different situations were tested: full or empty dead space and Pasteur’s chamber. The differences between the injected and measured volume varies from 0 to 5 ml representing a maximal error of 3 % regardless of the volume injected and the flow in ml/hour. The capacitive sensors behave as expected with a parallel curve of the expected and measured flow. Conclusion: We have shown in this in-vitro study that the combination of gravimetry and capacitive sensors analysis allow accurate measurement of volume and flow-output. Clinical trials should be conducted to confirm its usefulness in urine output measurement in the real life.

This article conceptualises the link between firms’ value chains and distribution networks and the requirements for double materiality assessments in contemporary reporting regulations worldwide. The new European Sustainability Reporting Standards (ESRS) and the standards for sustainability reporting issued by the International Sustainability Standards Board (ISSB), called IFRS S1 and IFRS S2, require companies to report their own direct (scope 1) and indirect (scope 2) greenhouse gas (GHG) emissions as well as GHG emissions in their value chains and distribution networks (both scope 3). However, GHG emissions comprise just one dimension of information that is relevant to understand when assessing, managing and reporting the footprints and impacts of a firm and are, therefore, only a fraction of the key performance indicators (KPIs) related to ESG that should be disclosed. Through a case study, this article demonstrates the connection between the due diligence analysis of firms’ value chains and distribution networks, the analysis of the competitive parameters of the business model, the identified impacts, risks and opportunities, and the double materiality perspective. The double materiality perspective prioritises actions based on probability and significance, creating a natural space to identify KPIs. The article concludes by applying the REGS model and illustrating how it can assist firms in identifying relevant KPIs based on double-materiality assessments.

Two extensions of the generalized double Lomax distribution are introduced - the spliced-scale generalized double Lomax distribution and the exponentiated generalized double Lomax distribution. Their properties are studied. Usefulness of the new distributions is shown by fitting them to stock returns datasets.

In this paper, we focus on variational Bayesian learning deterministic optimization methods for inference in biparametric exponential models where the parameters follow semiparametric regression structures. This combination of data models and algorithms contributes to solving real-world problems and reduces the computation time. This allows both the rapid exploration of many data models and the accurate estimation of the mean and variance functions through the connection between generalized linear models and graph theory. A simulation study was carried out to assess the performance of the deterministic approximation. Finally, herein, we present an application using macroeconomic data to emphasize the benefits of the proposed approach.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p &lt; 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

Urbanization is considered as a main indicator of regional economic development due to its positive effect on promoting industrial development; however, many regions, especially developing countries, are troubled by its negative effect — the aggravating environmental pollution. Many researchers have indicated that rapid urbanization stimulated the expansion of industrial production scale and increased industrial pollutant emissions. However, this judgement contains a grave deficiency in that urbanization not only expands industrial production scales but can also increase industrial labour productivity and change the industrial structure. To modify this deficiency, we first decompose the influence which urbanization impacts on industrial pollutant emissions into the scale effect, the intensive effect and the structure effect by using the Kaya Identity and the LMDI Method; second, we perform an empirical study of the three effects’ impacts by applying the spatial panel model with data from 282 Chinese cities between 2003 and 2013. Our results indicate that (1) there are significant reverse U-shapes between Chinese urbanization rate and its industrial pollutant emissions; (2) the scale effect and the structure effect have aggravated Chinese industrial waste water discharge, sulphur dioxide emissions and soot (dust) emissions, while the intensive effect has generated a decreasing and ameliorative impact on that aggravated trend. The definite relationship between urbanization and industrial pollutant emissions depends on the combined influence of the scale effect, the intensive effect and the structure effect; (3) there are significant spatial autocorrelations of industrial pollutant emissions between Chinese cities, but the spatial spillover effect from other cities does not aggravate local urban industrial pollutant emissions, we offer an explanation to this contradiction that the vast rural areas surrounding Chinese cities have served as sponge belts and have absorbed the spatial spillover of cities’ industrial pollutant emissions. According to the results, we argue that this type of decomposition of the influence into three effects is necessary and meaningful, it establishes a solid foundation for understanding the relationship between urbanization and industrial pollutant emissions, and effectively helps to meet relative policy making.

Mutual exclusion algorithms are at the heart of concurrent, distributed/parallel, real-time and operating systems. It is well-known that such algorithms are very difficult to analyze and in the literature different conjectures about starvation-freedom and the number of by-passes (also said the overtaking factor), which in turn affects the (hopefully) bounded waiting time that a process competing for entering the critical section has to suffer before accessing the shared resource, have been formulated for specific algorithms. This paper proposes a novel modelling approach based on Timed Automata and the Uppaal toolset, which proves effective for studying all the properties of a mutual exclusion algorithm for N≥2 processes, by exhaustive model checking. Although the approach, as already confirmed by similar experiments reported in the literature, is not scalable due to state explosion problems, and can be practically applied until N≤5, it is of great value for revealing true properties of analyzed algorithms. For dimensions N>5 the statistical model checker of Uppaal can be used which, although based on simulations, can confirm properties by estimations and probabilities. The paper describes the proposed modelling and verification method and applies it to several mutual exclusion algorithms, thus retrieving known properties but also showing new results about properties often studied only by peer-review and intuitive reasoning.