Humans are exposed to the environmental pollutants 2, 4-dichlorophenol (2, 4-DCP) and 2, 5-dichlorophenol (2, 5-DCP) through air, use of water and consuming products. In this study, we evaluated the urinary concentrations of these compounds in Korean people from the age of 18 to 69 years by making use of the data from the Korean National Human Biomonitoring Survey that was completed in 2009. Of 1,865 representative Koreans, 63.4% and 97.9% were found to have concentrations of 2, 4-DCP and 2, 5-DCP > 0.05 μg/L (limit of detection) in their urine. The geometric mean urinary concentrations were 0.14 μg/L (confidence interval of 95% = 0.13–0.16) and 0.44 μg/L (confidence interval = 0.41–0.48), respectively. It was fond that the adjusted proportional changes in 2, 4-DCP concentrations were significantly associated with body mass index, whereas those of 2, 5-DCP concentrations were influenced by place of residence. From these findings, it is evident that most adults in Korea have levels of 2, 4-DCP and 2, 5-DCP that are detectable in their urine and burden of these compounds on their bodies varies depending on numerous demographic factors.

In this work, pure TiO₂ and binary nanocomposites of Fe₃O₄/TiO₂ and Ag/TiO₂ were synthesized in order to improve photocatalytic performance of these samples for degradation of 2, 4-dichlorophenol (2, 4-DCP) as an organic pollutant. A range of analytical techniques including XRD, DRS, SEM/EDX, and elemental mapping were employed to reveal the crystal structure, morphology and property of the nanocomposites. XRD data demonstrated that the prepared samples are purely in TiO₂ anatase phase and cubic spinel Fe₃O₄ exist in the synthesized nanocomposite. We calculated the TiO₂ crystal size from XRD patterns, in the range of 8.35-11.09 nm. The presence of Ag, Fe, O, and Ti atoms in the synthesized nanocomposites was confirmed by SEM/EDX. We obtained 30.43, 32.02 and 42.40 % degradation of 2, 4-DCP (100 ml 2, 4-DCP 40 ppm and 0.01 g catalyst) for pure TiO₂, Fe₃O₄/TiO₂ and Ag/TiO₂, respectively, after 180 min of irradiation under visible light. Similar conditions were employed for 2, 4-DCP degradation under UV irradiation, we obtained 53.05, 51.00 and 71.50 % degradation of 2, 4-DCP pure TiO₂, Fe₃O₄/TiO₂ and Ag/TiO₂, respectively. Thus, the synthesized binary nanocomposites exhibited higher photocatalytic activity compared to pure TiO₂ under visible light.

4-(2-Methyloxazol-4-yl)benzenesulfonamide was synthesized by the reaction of 4-(2-bromoacetyl)benzenesulfonamide with an excess of acetamide. The obtained compound was evaluated as a potential inhibitor of human monoamine oxidase (MAO) A and B and was found to inhibit these enzymes with IC50 values of 3.47 μM for MAO-B and 43.3 μM for MAO-A. Thus, the new selective MAO-B inhibitor was identified, which may be used as the lead compound for development anti-Parkinson’s disease agents.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

The treatment of the bulky Rind-based dibromosilanes, (Rind)2SiBr2 (2) [Rind = 1,1,7,7-tetra-R1-3,3,5,5-tetra-R2-s-hydrindacen-4-yl: EMind (a: R1 = Et, R2 = Me) and Eind (b: R1 = R2 = Et)], with two equivalents of tBuLi in Et2O at low temperatures resulted in the formation of blue solutions derived from the diarylsilylenes, (Rind)2Si: (3). Upon warming the solutions above −20 °C, the blue color gradually faded, accompanying the decomposition of 3 and yielding the cyclic hydrosilanes (4) via intramolecular C−H bond insertion at the Si(II) center. The molecular structures of the bulky Eind-based 3b and 4b were confirmed by X-ray crystallography. Thus, at −20 °C, blue crystals were formed (Crystal-A), which were identified as mixed crystals of 3b and 4b. Additionally, colorless crystals of 4b as a singular component were isolated (Crystal-B), whose structure was also determined by an X-ray diffraction analysis. Although the isolation of 3 was difficult due to their thermally-labile nature, their structural characteristics and electronic properties were discussed based on the experimental findings complemented by computational results. We also examined the hydrolysis of 3b to afford the silanol, (Eind)2SiH(OH) (5b).

Healthcare professionals constantly face situations that reflect ecosystems’ degradation. These can negatively affect their mental health. Research suggests that hope and resilience can play an important role in this scenario, since they are related to/predict mental health in highly heterogeneous samples (considering geography, age, profession, health, etc.). In this context, the aims of the present study are: to characterize and explore the relationship between hope, resilient coping and mental health of Portuguese healthcare professionals. Using Google Forms, 276 healthcare professionals answered to the GHQ-28, the (adult) Trait Hope Scale, and the Brief Resilient Coping Scale (cross-sectional study). The minimum and maximum possible scores were reached, with the exception of the maximum score of GHQ-28-Total. Regarding Hope, 19.6% scored below the midpoint (M=43.46, SD=11.97); 29.3% revealed low resilience (M=14.93, SD=4.05); and the average of 4 of the 5 Mental Health scores (exception: Severe Depression) indicates the probability of a psychiatric case. Hope correlated with Social Dysfunction and GHQ-28-Total; resilient coping proved to be a (weak) predictor of 4 of the 5 GHQ-28 indicators (exception: Severe depression). The results support the need to promote the sample's mental health, hope and resilient coping. They also suggest that stimulating resilient coping may contribute to improving healthcare professionals’ mental health.

To mitigate pyrethroid resistance in mosquito vectors of emerging and re-emerging human pathogens, there is an urgent need to discover insecticides with novel modes of action. Natural alternatives, such as extracts derived from plants, may serve as substitutes for traditional synthetic insecticides if they prove to be sustainable, cost-effective, and safe for non-target organisms. Hemp (Cannabis sativa) is a sustainable plant known to produce various secondary metabolites with insecticidal properties, including terpenoids and flavonoids. The goal of this study was to assess the larvicidal activity of hemp leaf extract on 1st instar mosquito larvae from both pyrethroid-susceptible (PS) and pyrethroid-resistant (PR) strains of Aedes aegypti Another goal was to identify which components of the extracts were responsible for any observed larvicidal activity. We found that methanol extract of hemp leaves induced similar concentration-dependent larvicidal activity against PS (LC50: 4.4 ppm) and PR (LC50: 4.3 ppm) strains within 48 hours. Partitioning of the dried leaf extract between methanol and revealed that full larvicidal activity was restricted to the methanol fraction. Analysis of this fraction by gas chromatography-mass spectrometry and nuclear magnetic resonance showed it to be dominated by cannabidiol (CBD). Larvicidal assays using authentic CBD confirmed this compound was primarily responsible for the toxicity of hemp leaf extract against both strains. We conclude that hemp leaf extracts and CBD have the potential to serve as viable sources for the development of novel mosquito larvicides.

The focus of our study was the changes in the composition of semi-natural dry grasslands in Hungary. Since these valuable habitats were created with the help of humans, their preservation also requires regular treatment. Our mowing experiment aimed to investigate the suppression of the native Calamagrostis epigejos L. Roth. In Hungary, in the Cserhát Mountains, eight permanent plots were mowed twice a year. The vegetation was sampled annually between 2001 and 2011. The effects of mowing were investigated with repeated measures analysis of variance (ANOVA). After 10 years, the C. epigejos cover of the mowed plots decreased significantly, from the initial average of 62.38 to 7.50%. Surprisingly, we also experienced a similar decrease in the control plots. Regular treatment also had a positive effect on the number of species and diversity. Species richness increased continuously in both treatment types, which indicates the combined effect of vegetation succession and treatment. The biomass growth of other Poaceae and Fabaceae species, which are important from a grassland management perspective, was also facilitated by mowing. Our results suggest that long-term in situ experiments and continuous botanical studies are needed to establish a reliable utilization of grasslands.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

Introduction: The association of gene variants for interleukin 6(IL-6) (rs1800796), interleukin 10 (IL-10) (rs1800896) and tumor necrosis factorα (TNFα (rs1800629) with the occurrence of spontaneous preterm birth (PTB) was investigated to determine whether these genetic variants are a risk factor. Materials and methods: 199 blood samples from pregnant women who had given birth prematurely and 200 control blood samples were analyzed to determine single nucleotide polymor-phisms (SNPs) of genes for IL-6 (rs1800796), IL-10 (rs1800896) and TNFα (rs1800629). The control samples were samples from pregnant women with term delivery. Isolation of DNA was per-formed on mini-spin columns according to the manufacturer's protocol. The quality and purity of the isolated DNA were tested using a Qubit 3 fluorometer. Genotyping was performed with an ABI PRISM 7500 SDS using TaqMan SNP genotyping assays. The genotypes obtained were an-alyzed using the 7500 Software v2.3 package. Results: Carriers of the A/A genotype for the rs1800629 of the TNFα gene have 4.81 times greater chance of late-onset PTB compared to carriers of the G/G and A/G genotypes in the recessive inheritance model. The presence of the G/G genotype in the recessive inheritance model compared with the G/A and A/A genotypes for the rs1800896 of the IL-10 gene represents a potentially protective factor, with mothers in the term-birth group having an almost 2-fold lower odds of PTB in general and an almost 10-fold lower odds of early PTB. On the other hand, carriers of the A/G genotype of rs1800896 have a 1.54-fold higher chance of preterm birth in general and a 1.6-fold higher chance of late preterm birth in the super dominant inheritance model compared to the A/A and G/G genotypes in the group of mothers with PTB. In this study, no association was found between PTB and rs1800796 of the IL-6 gene. Conclusion: rs1800629 in mothers was associated with PTB. rs1800896 shows a potentially protective effect for the occurrence of PTB in this study. No association was found between PTB and rs1800796.

Background: Histone deacetylases (HDACs) are implicated in carcinogenesis, and HDAC inhibitors (HDACis) are explored as a therapeutic tool in several tumors. The aim of this study was to evaluate the clinical significance of HDAC -2, -4, and -5 expression in epithelial ovarian carcinoma (EOC). Methods: HDAC-2, -4, and -5 immunohistochemical expression was examined in 92 EOC tissue specimens and was correlated with clinicopathological characteristics. Results: HDAC-2 was the most frequently (94.4%) expressed isoform, being marginally higher in serous tumors compared with other types (p=0,08). HDAC-5 was the less frequently expressed (28.1%), being positively associated with HDAC-4. HDAC-4 positivity was associated with lower FIGO-stage (p=0,045) and T-category (p=0.,043) and the absence of lymph node (p=0,05) or distant metastasis (p=0,09) in serous carcinomas. HDAC-2 positivity was correlated with absence of lymph node metastasis in serous tumors (p=0,045). On the contrary, HDAC-5 nuclear positivity was correlated with lymph node metastasis in the entire cohort (p=0,048). HDAC-4 positivity was marginally associated with favorable prognosis in serous carcinomas in univariate survival analysis (p=0,086), a correlation which was not significant in multivariate analysis. Conclusion: These findings suggest a differential expression of HDAC-2, -4 and -5, providing evidence for a potential role in the pathobiology of EOC.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

The crystals, C11H4BrF5N2S, (I), 1-((4-bromothiophen-2-yl)methylene)-2-(perfluorophenyl)hydrazine and C12H6BrF5N2S, (II), 1-((4-bromo-5-methylthiophen-2-yl)methylene)-2-(perfluorophenyl)hydrazine are molecules with two rings and hydrazone part like a centre of the molecule. The compounds have been synthesized and characterized by elemental, spectroscopic (¹H-NMR) analysis. The crystal structures of the solid phase were determined by single crystal X-ray diffraction method. They crystallize in the monoclinic space group with Z = 4 and Z = 2 molecules per unit-cell. The compound (I) crystallizes as a racemate in the centrosymmetric space group and the compound (II) crystallizes as a non-racemate in the non-centrosymmetric space group. The “absolute configuration and conformation for bond values” were derived from the anomalous dispersion (ad) for (II). The crystal structures are revealed diverse non-covalent interactions such as intra- and interhydrogen bonding, π-ring···π-ring, C-H···π-ring and they were investigated. The expected stereochemistry of hydrazones atoms C7, N2 and N1 were confirmed for (I) and (II). The hole molecule of the (I), and (II) possesses “a boat conformation” like a 6-membered ring. The results of the single crystal studies are reproduced with the help of Hirshfeld surface study and Gaussian software.

"Public legal information from all countries and international institutions is part of the common heritage of humanity. Maximizing access to this information promotes justice and the rule of law". In accordance with the aforementioned declaration on Free Access to Law by Legal information institutes of the world, a plethora of legal information is available through the Internet, while the provision of legal information has never before been easier. Given that law is accessed by a much wider group of people, the majority of whom are not legally trained or qualified, diversification techniques, should be employed in the context of legal information retrieval, as to increase user satisfaction. We address diversification of results in legal search by adopting several state of the art methods from the web search, network analysis and text summarization domains. We provide an exhaustive evaluation of the methods, using a standard data set from the Common Law domain that we subjectively annotated with relevance judgments for this purpose. Our results i) reveal that users receive broader insights across the results they get from a legal information retrieval system, ii) demonstrate that web search diversification techniques outperform other approaches (e.g., summarization-based, graph-based methods) in the context of legal diversification and iii) offer balance boundaries between reinforcing relevant documents or sampling the information space around the legal query.

Urbanization is considered as a main indicator of regional economic development due to its positive effect on promoting industrial development; however, many regions, especially developing countries, are troubled by its negative effect — the aggravating environmental pollution. Many researchers have indicated that rapid urbanization stimulated the expansion of industrial production scale and increased industrial pollutant emissions. However, this judgement contains a grave deficiency in that urbanization not only expands industrial production scales but can also increase industrial labour productivity and change the industrial structure. To modify this deficiency, we first decompose the influence which urbanization impacts on industrial pollutant emissions into the scale effect, the intensive effect and the structure effect by using the Kaya Identity and the LMDI Method; second, we perform an empirical study of the three effects’ impacts by applying the spatial panel model with data from 282 Chinese cities between 2003 and 2013. Our results indicate that (1) there are significant reverse U-shapes between Chinese urbanization rate and its industrial pollutant emissions; (2) the scale effect and the structure effect have aggravated Chinese industrial waste water discharge, sulphur dioxide emissions and soot (dust) emissions, while the intensive effect has generated a decreasing and ameliorative impact on that aggravated trend. The definite relationship between urbanization and industrial pollutant emissions depends on the combined influence of the scale effect, the intensive effect and the structure effect; (3) there are significant spatial autocorrelations of industrial pollutant emissions between Chinese cities, but the spatial spillover effect from other cities does not aggravate local urban industrial pollutant emissions, we offer an explanation to this contradiction that the vast rural areas surrounding Chinese cities have served as sponge belts and have absorbed the spatial spillover of cities’ industrial pollutant emissions. According to the results, we argue that this type of decomposition of the influence into three effects is necessary and meaningful, it establishes a solid foundation for understanding the relationship between urbanization and industrial pollutant emissions, and effectively helps to meet relative policy making.

Disease, trauma, and aging account for a significant number of clinical disorders. Regenerative medicine is emerging as a very promising therapeutic option. The design and development of new cell-customized biomaterials able to mimic ECM functionalities represent one of the major strategy to control the cell fate and stimulate tissue regeneration. Recently, hydrogels have received a considerable interest for their use in the modulation and control of cell fate during regeneration processes. Several synthetic bioresponsive hydrogels are being developed in order to facilitate cell-matrix and cell-cell interactions. In this review new strategies and future perspectives of such synthetic cell microenvironment will be highlighted.

Benzazoles, such as benzoxazoles and benzothiazoles, are compounds with important biological and pharmacological activities and important intermediaries in synthesis. This report presents a linear synthesis of a butanamide derived from linking 5-chloro-2-aminobenzoxazole and 2-aminobenzothiazole via 4-chlorobutanoyl chloride. The corresponding compound N-(benzothiazol-2-yl)-4-((5-chlorobenzoxazol-2-yl)aminobutanamide was obtained in good [PVG1] yield using accessible starting materials and methodology in two reaction steps. Furthermore, we made docking studies of this compound on 3-TOP protein to explore its potential as an antidiabetic agent with an excellent yield.

A Cu₂ZnSnS₄ (CZTS) film with a thickness of approximately 1.5 μm was fabricated on a Mo-coated glass substrate by annealing a CZTS precursor fabricated from nanoparticle ink. The chemical states of the elements in the CZTS thin film in the depth direction were studied to identify the presence of secondary phases, which are detrimental to the performance of solar cells containing CZTS. X-ray diffraction was unable to detect any secondary phases in CZTS because of their small relative amount. Instead, X-ray photoelectron spectroscopy (XPS), which is highly sensitive to chemical state, was conducted at different depths in the CZTS film to further check the presence of secondary phases. XPS analysis revealed peaks shift consistent with the presence of secondary phases. For the CZTS film annealed in a S atmosphere at 575 °C for 3 h, the film surface consisted of a secondary-phase layer composed of CuS, ZnS, and SnSx (x=1 or 2) originating from the decomposition of CZTS. At depths below 80 nm, the film was pure CZTS. Formation of MoS2 at the CZTS–Mo interface was confirmed by XPS analysis of Mo and S.

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic and it represents a pollutant of global concern. Liquid Hg is highly volatile and it can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paints, plasters, roof tiles, concretes, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into 7 units) covers a surface of about 65 ha and contains mining structures and managers and workers buildings. In this work, nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in the units 2, 3 and 6. Moreover, detailed measurements were performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in terms of space and time mostly depending on the distance from the building hosting driers, furnaces and condensers and ambient temperature, respectively. In the Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng m⁻³, while in the Unit 6 they were on average much higher and occasionally they saturated the GEM measurement device (>50,000 ng m⁻³). Concentrations of total (in mg kg⁻¹) and leached (in μg L⁻¹) mercury measured in different building materials (up to 46,580 mg kg⁻¹ and 4,470 mg L⁻¹ for total and leached mercury, respectively) showed for the same type of material highly variable values in dependence on the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for the operational cleanings to be carried out during the reclamation activities.

In an effort to discover an effective and selective antitumour agent, synthesis and anti-cancer potential of 4-(pyridin-4-yl)-6-(thiophen-2-yl)pyrimidin-2(1H)-one (SK-25), which has been reported earlier by us with significant cytotoxicity towards MiaPaCa-2 malignant cells, with an IC₅₀ value of 1.95 μM and was found to instigate apoptosis. In the present study, the antitumour efficacy of SK-25 was investigated on Ehrlich ascites tumour (solid), Sarcoma 180 (solid) tumour and Ehrlich ascites carcinoma. The compound was found to inhibit tumour development by 94.71% in Ehrlich ascites carcinoma (EAC), 59.06% in Ehrlich tumour (ET, solid) and 45.68% in Sarcoma-180 (solid) at 30 mg/kg dose. Additionally, SK-25 was established to be non-toxic at a maximum tolerated dose of 1000 mg/kg in acute oral toxicity in Swiss-albino mice. Computer-based predictions also show that the compounds could have an interesting DMPK profile. The current study provides insight for further investigation of the antitumour potential of the molecule.

Introduction: Hypertension is a serious public health problem in Morocco. The objective of this pilot study was to estimate the salt intake of Moroccan adults by measuring 24-hour urinary sodium excretion. Methods: 132 participants were recruited from the central region of Morocco. Sodium, potassium and creatinine levels were measured using the 24-hour urine samples. Additional data included anthropometric measurements and socio-demographic questionnaire. Results: The daily sodium, potassium and creatinine excretions were 2779.1±1334.9 mg, 1350.0±642.8 mg and 820.3 ± 381.2 mg, respectively. Data analysis revealed that 71.2% of the participants had a daily sodium intake more than 2000 mg (5g of salt) recommended by the WHO. The mean of potassium excretion was 1350.0±642.8 mg /day, this average was lower than 3.51g per day recommended by the WHO. Conclusion: Public health measures to reduce sodium and increase potassium consumption in order to decrease the population’s risk of high blood pressure and heart disease are recommended.

(S)-1-Methyl-2-oxoimidazolidine-4-carboxylic acid 1 is an analog of (S)-pyroglutamic acid, a key component of naturally occurring peptide hormones and synthetic pharmaceutical candidates. Reaction of (S)-2-amino-3-(methylamino)propionic acid with COCl2 and aqueous NaHCO3 followed by ion exchange afforded 1, which was recrystallized from acetonitrile and then characterized by IR, 1H NMR, 13C NMR, polarimetry, elemental microanalysis, high resolution mass spectrometry and single crystal X-ray diffraction. The acid 1 crystallized in the orthorhombic chiral space group P212121 with cell constants a = 6.2275(4) Å, b = 8.3963(5) Å, c = 24.9490(14) Å. The X-ray crystal structure reveals that two distinct conformers of 1 occur at alternating positions within helices which are supported by hydrogen-bonding. Each molecule of 1 is linked to its two neighbors in the helix by a total of three hydrogen bonds and four molecules of 1 are contained within each turn of the helix. The pattern of hydrogen bonds illustrates a preference for the carboxylic acid group to act as a hydrogen bond donor and for the urea unit to be a hydrogen bond acceptor.

The oxidative stress is one of the main cause for cardiovascular diseases (like Hypertension) also one of the results of these diseases. This study involved 56 subjects matched ages and sex divided into two groups; 28 hypertensive subject and 28 healthy subject as control group. The following analysis was done: 4-Hydroxy-2-nonenal(4HNE) and albumin. The results show that there is a significant increase in (4HNE) between patients group and control group. The increase in 4HNE which is a product of lipid peroxidation is attributed to destruction in body cell caused by due to the increase in stress events. It has been concluded that is important nappy on ideal weight, because obesity considered main factors for heart disease and hardening of the arteries. The aim of this study was to investigate the relationship between of some oxidative stress markers and cardiovascular diseases.

The present study comprises the second part of our previous work that dealt mainly with the phytochemical and physicochemical characterization of green coffee, clove, cinnamon/clove and nutmeg ethanolic extracts of grape origin. In the present study, we focused on producing a discriminating model concerning green coffee, clove, cinnamon, cinnamon and clove, and nutmeg fine powders based on multivariate analysis of variance and supervised learning on data of volatile compounds analysis, carried out with solid phase dynamic extraction in combination with gas chromatography/mass spectrometry. Results showed that 7 volatile compounds namely ethylene, methanol, 3-methylpentane, ethyl acetate, 9-hexadecen-1-ol, toluene, and methyl acetate could differentiate the investigated samples resulting in a 100% classification rate using the cross-validation method of linear discriminant analysis. Results were further confirmed using partial least squares regression analysis. The study contributes to the typification of green coffee, cinnamon, clove, cinnamon and clove and nutmeg, based on selected volatile compounds, and provides further support to the literature by means of possible adulteration given the statistical models developed.

In this work, optimal consumption and investment strategies are derived for risk-averse investors under the 4/2 stochastic volatility class of models. We work under an expected utility (EUT) framework and consider a Constant Relative Risk Aversion (CRRA) investor, who might also be ambiguity-averse. The corresponding Hamilton-Jacobi-Bellman (HJB) and HJB-Isaacs (HJBI) equations are solved in closed-form for a subset of the parametric space and under some restrictions on the portfolio setting, for complete markets. Conditions for proper changes of measure and well defined solutions are provided. These are the first analytical solutions for the 4/2 stochastic volatility model and the embedded 3/2 model for the type of excess returns established in .

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Simple Summary: The distribution of typical bacterial redox enzymes such as pyruvate-ferredoxin oxidoreductase (PFOR) in protozoa remains interestingly puzzling. Previous studies have demonstrated diverse cellular localizations of PFOR in some amitochondriate anaerobic protozoa. PFOR is of particular pharmacological importance because it catalyzes the reductive bio-activation of nitro-based prodrugs to cytotoxic radical metabolites. Metronidazole was developed primarily as an antiprotozoal agent against infections caused by Trichomonas vaginalis. However, its antimicrobial spectrum was subsequently expanded to cover anaerobic bacterial infections. It has been shown that mutations in the genes encoding PFOR result in inherent resistance of PFOR-possessing anaerobic protozoa and bacteria to nitro-based prodrugs. Deciphering the evolutionary history of PFOR is crucial in deepening our understanding of the evolution of anaerobic pathogens and unfold new approaches for drug discovery and targeting in pathogen chemotherapy. Abstract: The present frontrunners in the chemotherapy of infections caused by protozoa are nitro-based prodrugs that are selectively activated by PFOR-mediated redox reactions. This study seeks to analyze the distribution of PFOR in selected protozoa and bacteria by applying comparative bioinformatics approaches to test the hypothesis that PFOR was most likely acquired through horizontal gene transfer (HGT) from bacteria. Furthermore, to identify other genes that were putatively acquired using proteome-wide and gene expression analyses. A plausible explanation for the patchy occurrence of PFOR in protozoa is based on the hypothesis that bacteria are potential sources of genes that enhance optimal adaptation of protozoa in hostile environments. The exclusively expressed proteins obtained from Entamoeba histolytica and the putative gene donor, Desulfovibrio vulgaris, showed an over-expression of eleven genes involved in intermediary metabolism. If these results can be reproduced in other PFOR-possessing protozoa, it would provide a more validated evidence to support the horizontal transfer of pfor from bacteria.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Survivors of severe brain injury may require care in a neurointensive care unit (neuro-ICU), where the brain is vulnerable to secondary brain injury. Thus, there is a need for noninvasive, bedside, continuous cerebral blood flow monitoring approaches in the neuro-ICU. Our goal is to address this need through combined measurements of EEG and functional optical spectroscopy (EEG-Optical) instrumentation and analysis to provide a complementary fusion of data about brain activity and function. The present case demonstrates in a patient with traumatic brain injury, noninvasive cerebral blood flow transients can be recorded that correlate with gold-standard invasive measurements and with the frequency content changes in the EEG data during clinical care.

1-[5-(4-methylphenyl)-1,3,4-oxadiazol-2-yl]methanamine compound has been successfully synthesized by reacting p-Toluic hydrazide and glycine via polyphosphoric acid condensation route. The course of the reaction was found to be high yielding and the title compound was spectroscopically characterized by FT-IR, DSC, 13C/1H-NMR and Mass spectrometric techniques.

The treatment of acute myeloid leukemia (AML) with adverse genetics remains unsatisfactory, with very low response rates to standard chemotherapy and shorter durations of remission commonly observed in these patients. The complex biology of AML with adverse genetics is continuously evolving. Herein, we discuss recent advances which have investigated the contribution of cell intrinsic mechanisms as well as of the immune system to myeloid leukemogenesis in this specific subset of AML. We focus on the biological rationales for combining targeted therapy and immunotherapy, which are currently being investigated in ongoing trials, and could hopefully ameliorate the poor outcomes for these patients

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

Transition-metal-free synthesis of 4-pyrones via TfOH-promoted nucleophilic addition/cyclization of diynones and water has been developed. This transformation is simple, atom economical and environmentally benign, providing rapid and efficient access to substituted 4-pyrones.

Lynch syndrome (LS) is one of the most common hereditary cancer syndrome in human populations, associated with germline variants in MLH1, MSH2/EPCAM, MSH6 and PMS2 genes. The advent of next generation sequencing has proven a significant impact in germline variant detection in the causative genes; however, a large proportion of patients with clinical criteria still receive uncertain or negative results. PMS2 is the least frequent reported gene, associated with up to 15% of LS cases with late-onset disease and low penetrance phenotype; however, the proportion of PMS2-LS cases is considered to be highly underestimated. In this context, we consulted public available databases (ClinVar, LOVD) for missense and intronic PMS2 variants and performed an in silico analysis of the genomic sequence. Splicing bioinformatics tools proven effective in other genes were used to assess both the wild-type DNA sequence and reported genetic variants. Splicing alterations were predicted in silico and using GTEx short-read RNA expression data. Out of the 2384 missense variants discovered, 90% were classified with uncertain significance (VUS). 4.9% of missense variants were shown to have a potential splicing consequence (DS > 0.2) using SpliceAI. As described in the original publication, SpliceAI-visual was proven effective in annotation of short intronic variants (< 50 bp). Four short intronic variants were identified using SpliceAI-visual as potentially splicing disturbing, in spite of using a lower threshold (DS > 0.1). Moreover, we observed that Splicing Regulatory Elements (SREs) may play a fundamental role in alternative splicing in PMS2 gene, ESE motifs being overrepresented in highly expressed exons 5, 11 and 14. Computational analysis performed in our study serves as a valuable filtering step for guiding further RNA sequencing experiments. Additional functional data is necessary to evaluate the significance of our findings.

Zwitterionic polymers emerge as very useful materials for applications in antifouling surfaces. The properties of these polymers can be tuned by variation of the chemical structure of the corresponding monomer. In this study, two zwitterionic ammonium sulfonate monomers bearing an hydroxyl function and a styrenic polymerizable groups were prepared in two steps. The two monomers were obtained using 4-vinylbenzyl chloride as the key precursor. The zwitterionic monomers were characterized by 1H NMR, 13C NMR, IR spectroscopy and high-resolution mass spectrometry (HRMS). These two monomers enable the preparation of novel zwitterionic polymers with enhanced hydrophilicity due to the presence of a hydroxyl group.

Observe the synergistic effect and dose-effect relationship of Trimethoprim (TMP) on bactericidal activity with Flos Lonicerae in vitro. Microamount chessboard dilution method was conducted to determine the minimal inhibitory concentration (MIC) of Trimethoprim, Flos Lonicerae, as well as the combination of Trimethoprim and Flos Lonicerae separately against Staphylococcus aureus, Escherichia coli in vitro and Salmonella. The pour plate count method was used to determine the combined bactericidal activity of Flos Lonicerae combined with Different concentrations TMP. The results showed that the MIC values of the combination of Flos Lonicerae with TMP was much less than the MIC values of the independent use of Flos Lonicerae or TMP, The FIC values of the combination of Flos Lonicerae with TMP were between 0.5 and 1, there was additive effect between them. The bactericidal rates were fitted with least square method, the 95% confidence intervals of the optimal blending quantity about the combination of Flos Lonicerae with TMP on the test organisms were 231μg·mL^-1-249μg·mL^-1, 237μg·mL^-1-259μg·mL^-1, and 235 -259μg·mL^-1

Objectives: The study aimed to develop a deep learning-based edge AI model deployed on electrocardiograph (ECG) devices for real-time detection of atrial fibrillation (AF)-risk during sinus rhythm (SR) using standard 10-second 12-lead electrocardiograms (ECGs). Methods: A novel approach was used to convert standard 12-lead ECGs into binary images for model input, and a lightweight convolutional neural network (CNN)-based model was trained using data collected by the Japan Agency for Medical and Research Development (AMED) between 2019 and 2022. Patients over 40 years old with digital, SR ECGs were retrospectively enrolled and divided into AF and non-AF groups. Data labeling was supervised by cardiologists. The dataset was randomly allocated into training, validation, and internal testing datasets. External testing was conducted on data collected from other hospitals.　Results: The best-trained model achieved an AUC of 0.82 and 0.80, sensitivity of 79.5% and 72.3%, specificity of 77.8% and 77.7%, precision of 78.2% and 76.4%, and overall accuracy of 78.6% and 75.0% in the internal and external testing datasets, respectively. The deployed model and app package utilized 2.5MB and 40MB of the available ROM and RAM capacity on the edge ECG device, correspondingly. Processing time for AF-risk detection was approximately 2 seconds.　Conclusion: The model maintains comparable performance and improves its suitability for deployment on resource-constrained ECG devices, thereby expanding its potential impact to a wide range of healthcare settings. Its successful deployment enables real-time AF-risk detection during SR, allowing for timely intervention to prevent AF-related serious consequences like stroke and premature death.

Diabetes mellitus (DM) poses a significant challenge to global health, with its prevalence projected to rise dramatically by 2045. This narrative review explores the bidirectional relationship between periodontitis (PD) and type 1 diabetes mellitus (T1DM), focusing on cellular and molecular mechanisms derived by the interplay between oral microbiota and the host immune response. A comprehensive search of literature published between 2008 and 2023 was conducted to elucidate the association between these two diseases. Preclinical and clinical evidence suggests a bidirectional relationship, with individuals with T1DM exhibiting heightened susceptibility to periodontitis, and vice versa. The review includes recent findings from human clinical studies, revealing variations in oral microbiota composition in T1DM patients, including increases in certain pathogenic species such as Porphyromonas gingivalis, Prevotella intermedia, and Aggregatibacter actinomycetemcomitans, along with shifts in microbial diversity and abundance. Molecular mechanisms underlying this association involve oxidative stress and dysregulated host immune responses, mediated by inflammatory cytokines such as IL-6, IL-8, and MMPs. Furthermore, disruptions in bone turnover markers, such as RANKL and OPG, contribute to periodontal complications in T1DM patients. While preventive measures to manage periodontal complications in T1DM patients may improve overall health outcomes, further research is needed to understand the intricate interactions between oral microbiota, host response, periodontal disease, and systemic health in this population.

The Biginelli reaction is a highly versatile reaction, which leads to dihydropyrimidinones/thiones. This scaffold is reported as being a privileged structure due to its ability to interact with biological targets. Synthesis of ethyl 4-(2-fluorophenyl)-6-methyl-2-thioxo-1-(p-tolyl)-1,2,3,4-tetrahydropyrimidine-5-carboxylate was achieved through the Biginelli reaction using a functionalized thiourea. In silico studies demonstrated that the compound title showed good potential for interacting with ecto-5’-nucleotidase, which has been considered as a target in designs for anti-cancer drugs.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

In this paper the one-to-one correspondences and equivalences between ideals, primals, filters and grills are introduced. It is shown the local functions and the topological spaces induced by them are the same. From this point of view, the topological properties with respect to one topology can be derived from topological properties valid in the corresponding topology.

We report here the synthesis and characterization of new N-(3-(8-bromoimidazo[1, 2-a]pyridin-2-yl)-4-fluorophenyl)benzamide derivatives. This collection was obtained from 3-(8-bromoimidazo [1,2-a]pyridin-2-yl)-4-fluoroaniline(5). The family of new compounds was characterized by ¹H-NMR, ¹³C-NMR, FT-IR and LC-MS analysis.

Objective: Mechanical bowel preparation is essential for the visualisation of the colon during colonoscopy, and previous studies have identified changes in gut microbiota composition after bowel preparation and colonoscopy. Considering the gut microbiota is increasingly implicated in mood, we aimed to explore the potential impact of this intervention on mood and the microbiota-gut-brain axis. Methods: We conducted a pre-post intervention study, with timepoints of one week before and one month after bowel preparation and colonoscopy, in community-dwelling adults referred for colonoscopy. Our primary outcome was change in average Hospital Anxiety and Depression Scale depression sub-scores using generalised estimating equations. We also examined changes in average anxiety, stress, and quality of life scores, and faecal microbiota composition and potential function using 16S rRNA sequencing. We further explored associations between changes in depressive symptoms and the gut microbiota and conducted post-hoc analyses to explore potential effect modifiers. Key Results: 59 participants were included in the analyses. Depressive symptoms decreased one-month post-procedure compared to baseline (adjusted β=−0.64; 95%CI: −1.18, −0.11). Irritable bowel syndrome (IBS) appeared to moderate this relationship (1.78; 0.292, 3.26); depressive symptoms increased in those with, and decreased in those without, IBS. Changes in gut microbiome composition included reduced alpha diversity, modest effects on beta-diversity, and increases in genera associated with potential health benefits, one-month post-procedure compared to baseline. Increases in the CLR-transformed abundance of Ruminococcaceae UCG-009 were associated with improvements in depressive symptoms. Conclusions: There is preliminary evidence of a potential mental health effect of bowel preparation and colonoscopy, which may be associated with changes to the gut microbiota. There may also be a differential mental health impact of this procedure for those with and without IBS. Considering the limitations of our study, further research is required to confirm these findings and their clinical relevance.

Antibiotic prescription is the first line of treating bacterial diseases. But it affects the composition and function of non-targeted intestinal microbiota. Antimicrobial resistance will be the cause for the death of millions of people worldwide. By considering collateral damage of antibiotics, searching an alternative antimicrobial agent will be a solution to minimize the problems. Probiotics, prebiotics and synbiotics are an alternative to antibiotics. Thanks to GIT microbes as they are responsible for metabolism, energy production, protection from pathogens and immunomodulation. So, it is appreciable if the gut microbiota modulated through consumption of probiotics, prebiotics and synbiotics. Probiotic effects are genus and species specific. To get good health benefit of probiotics, safety of probiotics should be assessed before using them. This is mandatory for prebiotics and synbiotic selection. So this review paper gives information about side effects of antibiotics on gut microbiota, description of probiotics, prebiotics and synbiotics as alternative to antibiotics in modulating GIT microbiota, techniques of assessing safety of probiotics and health benefits of probiotics, prebiotics and synbiotics with scientific evidence in clinical trial and some disagreement and challenges of using probiotics, prebiotics and synbiotics.

In this data deposit, I describe a dataset that is the result of content mining 167,318 published articles for statistical test results. As a result of this content mining, 688,112 results from 50,845 articles were extracted. In order to provide a comprehensive set of data, the statistical results are supplemented with metadata from the article they originate from. The dataset is provided in a comma separated file (CSV) in long-format. For each of the 688,112 results, 20 variables are included, of which seven are article metadata and 13 pertain to the individual statistical results (e.g., reported and recalculated p-value). A five-pronged approach was taken to generate the dataset: (i) collect journal lists, (ii) spider journal pages for articles, (iii) download articles, (iv) add article metadata, and (v) mine articles for statistical results.

Recent experiments devoted to characterizing the behavior of sessile ferroelectric liquid droplets on ferroelectric solid substrates, showed the existence of a droplet electromechanical Rayleigh-like instability. The instability is induced by the bulk polarization of the ferroelectric fluid which couples to the polarization of the underlying substrate through its fringing field and solid-fluid interface coupling. With the aim of characterizing this phenomenon, namely the coupling between the polarizations of a fluid and a solid material, we studied the behavior of ferroelectric liquid droplets confined between two solid substrates, arranged in different configurations realized so to generate fringing fields with different profiles. Results show that the features of the droplets instability are indeed affected by the specific fringing field shape in a way dominated by the minimization of the electrostatic energy associated to the bulk polarization of the ferroelectric fluid.

Amidst worsening climate change, drought stress imperils global agriculture, jeopardizing crop yields and food security, necessitating urgent exploration of sustainable methods like biopriming, harnessing beneficial microorganisms to bolster plant resilience. Recent research has revealed diverse biological compounds with versatile applications produced by Schizophyllum commune, rendering this fungus as a promising contender for biopriming applications. For the first time this study aimed to investigate,the potential of S. commune exo- (EPSH) and intra-PSH (IPSH), isolated from two strains: Italian (ITA) and Serbian (SRB) under submerged cultivation, in enhancing the resilience of Pisum sativum L. seeds through biopriming technique. Testing of seed quality of bioprimed, hydroprimed, and unprimed seeds was done using a germination test, under optimal and drought conditions. In optimal conditions, the IPSH SRB increased germination energy by 5.50% compared to the control, while the highest percentage of germination (94.70%) was shown after biopriming with PSH isolated from the ITA strain. Additionally, all assessed treatments resulted in a boost in seedling growth and biomass accumulation, where the ITA strain demonstrated greater effectiveness in optimal conditions, whereas the SRB strain showed superiority in drought conditions. The drought tolerance indices increased significantly in response to all examined treatments during the drought, with EPSH ITA (23.00%) and EPSH SRB (24.00%) demonstrating the greatest effects. Results demonstrate a significant positive influence of fungal PSH, indicating their potential as biopriming agents and offers insights into novel strategies for agricultural resilience in the face of changing environmental conditions.

Keywords: Marine Coasts; Protected Areas; Defense and Conservation; Asbestos Cement Materials; Wastes; Contamination; Human Health Risk; Medical Geology.

2-(5,6-diphenyl-1,2,4-triazin-3-yl)pyridinium dichloroiodate (I) (1) was synthesized by reacting 3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine with ICl in dichloromethane solution. The structural characterization of 1 by SC-XRD analysis was accompanied by elemental analysis, FT-IR, and FT-Raman spectroscopy measurements.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Injury to the peritoneum during surgery is followed by a healing process that frequently results in the attachment of adjacent organs by a fibrous mass, referred to commonly as adhesions. Because injuries to the peritoneum during surgery are inevitable, one must understand the mechanisms of adhesion formation to prevent its occurrence. This requires a thorough understanding of the molecular sequence that results in the attachment of injured peritoneum and the development of fibrous tissue. Recent data show that fibroblasts from the injured peritoneum may play a critical role in forming adhesion tissues. Therefore, identifying changes in gene expression patterns in the peritoneal fibroblasts during the process may provide clues to the mechanisms by which adhesion develops. This review presents many papers discussing genes implied in peritoneal adhesion.

Background: Acute kidney disease (AKD) is a known risk factor for increased mortality and evolution towards chronic kidney disease (CKD) in adults. The data regarding children are scarce. The purpose of our study is to explore the risk factor for AKD and impact of AKD following an acute kidney injury (AKI) episode in children on mortality and new-onset CKD. Methods: We retrospectively evaluated 736 children with ages between 2 and 18 years old with AKI admitted in a tertiary care hospital from the west Romania over a 9 years period. Results: AKD incidence following AKI was 17%. Patients that developed AKD were older, with higher baseline serum creatinine values, urea, C reactive protein and lower proteins, haemoglobin and sodium. They were more often exposed to sepsis, critical illness and nephrotoxic medications and presented certain susceptibilities like CKD, neoplasia, anemia, heart failure, arterial hypertension, stem cell transplant and female gender. AKI causes that increased the risk of AKD were intrinsic ones. AKD increased the overall mortality by three times. The factors that independently increased the risk of evolution towards CKD were AKD, acute tubular necrosis and higher baseline serum creatinine values. Conclusions: AKD is an independent risk factor for mortality and new-onset CKD in children.

Breast cancer (BC) ranks among the most prevalent cancers diagnosed in women. Its treatment necessitates precision tailored to the cancer's genetic makeup for enhanced efficacy. Research has been directed towards natural compounds for their anti-BC properties, aiming to augment existing treatment modalities. Chromolaena tacotana (Klatt) R.M. King and H. Rob, commonly referred to as Ch. tacotana, is a notable source of bioactive hydroxy-methylated flavonoids. However, the specific anti-BC mechanisms of these flavonoids, particularly those present in the plant's inflorescences, remain partly undefined. This study focuses on assessing a chalcone derivative extracted from Ch. tacotana inflorescences for its potential to concurrently activate regulated autophagy and intrinsic apoptosis in Luminal A and triple-negative BC cells. We determined the chemical composition of the chalcone using ultraviolet (UV) and nuclear magnetic resonance (NMR) spectroscopy. Its selective cytotoxicity against BC cell lines was assessed using the MTT assay. Flow cytometry and western blot analysis were employed to examine the modulation of proteins governing autophagy and the intrinsic apoptosis pathway. Additionally, in silico simulations were conducted to predict interactions between the chalcone and various anti-apoptotic proteins, including the mTOR protein. The chalcone was identified as 2',4-dihydroxy-4',6'-dimethoxy-chalcone (DDC), also known as Flavokavain C (FKC). This compound demonstrated selective inhibition of BC cell proliferation and triggered autophagy and intrinsic apoptosis. It induced cell cycle arrest in the G0/G1 phase and altered mitochondrial outer membrane potential (∆ψm). The study observed the activation of autophagic LC3-II and mitochondrial pro-apoptotic proteins in both BC cell lines. The regulation of Bcl-XL and Bcl-2 proteins varied according to BC subtype, yet they showed promising molecular interactions with DDC. Among the examined pro-survival proteins, mTOR and Mcl-1 exhibited the most favorable binding energies and were downregulated in MCF-7 and MDA-MB-231 cell lines. Further research is needed to fully understand the molecular dynamics involved in the activation and interaction of autophagy and apoptosis pathways in cancer cells in response to potential anticancer agents like the hydroxy-methylated flavonoids from Ch. tacotana.

The reaction of 2-bromo-1-(5-methyl-1-(4-nitrophenyl)-1H-1,2,3-triazol-4-yl)ethan-1-one (1) with 4-amino-5-((2,4-dichlorophenoxy)methyl)-4H-1,2,4-triazole-3-thiol (2) in absolute ethanol in the presence of triethyl amine as catalyst gave 2-((4-amino-5-((2,4-dichlorophenoxy)methyl)-4H-1,2,4-triazol-3-yl)thio)-1-(5-methyl-1-(4-nitrophenyl)-1H-1,2,3-triazol-4-yl)ethan-1-one (3) in 73% yield. The structure of the title heterocycle (3) was confirmed by X-ray single crystal diffraction and spectral analyses (NMR and IR).

Although ovarian cystic teratoma is the most common ovarian tumor, complications are quite rare. However, it is important to be recognized by the radiologist in order to avoid inaccurately diagnosing them as malignant lesions. This case report describes a 61-year-old postmenopausal woman, who presented to the emergency room with abdominal pain following a minor blunt abdominal trauma. In this context, a CT scan was performed, which showed the presence of round, hypodense masses randomly distributed in the peritoneum, with coexisting ascites in moderate amount; ovarian carcinoma with peritoneal carcinomatosis was suspected. The patient was hospitalized and an MRI of the abdomen and pelvis was recommended for a more detailed lesion characterization. Following this examination, the patient was diagnosed with mature cystic ovarian teratoma complicated by rupture. Surgery was performed, and the outcome was favorable. The cases of ruptured cystic teratomas are rare, and to our knowledge, this is the first occurrence described in literature. Special attention must be paid when confronting with such a case in medical practice, since it can easily misdiagnosed as peritoneal carcinomatosis

This paper presents the PEnsemble 4 model, a sophisticated machine learning framework that integrates IoT-based environmental data to accurately forecast maize yield. With the projected significant growth in global maize demand over the next decade, the inherent risks posed by the crop’s dependence on weather conditions necessitate improved prediction capabilities. The PEnsemble 4 model, developed with high accuracy, incorporates comprehensive datasets encompassing soil attributes, nutrient composition, weather conditions, and UAV-captured vegetation imagery. By employing a combination of Huber and M estimates, the PEnsemble 4 model effectively analyzes temporal patterns in vegetation indices, specifically CIre and NDRE, which serve as reliable indicators of canopy density and plant height. In addition, this research significantly contributes to precision agriculture by offering an efficient and sustainable alternative to conventional farming practices through precise yield predictions. Notably, the PEnsemble 4 model enables earlier estimation, advancing the timeline for yield prediction from the conventional day 100 in the R6 stage to day 79 in the R2 stage. This improvement enhances decision-making processes in farming operations. The remarkable accuracy rate of 91% underscores the importance of adopting a multifaceted data approach that harnesses IoT-derived environmental insights. Additionally, the PEnsemble 4 model extends its benefits beyond yield prediction, facilitating the detection of water and crop stress, as well as disease monitoring in broader agricultural contexts. Ultimately, the PEnsemble 4 model establishes a new standard in maize yield prediction, revolutionizing crop management and protection through the synergistic utilization of IoT and machine learning technologies.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

2-(Morpholin-4-yl)-4,5-bis(2’’,2’’,2’’-trinitroethoxy)-1,3,5-triazine having QSAR-predicted anti-tumor activity was tested for the cytotoxicity using MTT and LDH cell viability tests. The experiments were conducted using human fibroblasts, peripheral blood mononuclear cells and breast cancer cells and allowed to identify effective cytotoxic concentration ant therapeutic range of this compound. The data obtained suggest the feasibility of the further studies of the test compound as a potential anti-cancer agent.

Nowadays, animal breeders look for effective innovations to care animal health. Use of probiotics, postbiotics, parabiotics and the other beneficial natural substances are dominated. Mundticin-like substance EM 41/3 is thermo-stable bacteriocin (postbiotic) with a broad antimicrobial spectrum. In this study its effect in broiler rabbits was assessed. Rabbits represent food-derived animal and they are also suitable animal model. The parameters tested were analyzed by validated methods. Administration of MLS EM 41/3 produced by non-autochthonous strain Enterococcus mundtii EM 41/3 lead to significant increase of parameter immunity-phagocytic activity, while it did not influence microbiota composition. It also did not influence blood biochemistry and no oxidative stress was noted. Moreover, higher growth parameters were noted and also stimulated hydrolytic activity. Finally, no negative influence on rabbit meat quality was noted. Postbiotic MLS EM 41/3 administration in feeding strategy seems to be contributing fact for rabbit health status maintaining.

This study proposes an innovative pharmacovigilance approach, VIGI-4, leveraging ChatGPT Teams Pro version. Our method involves aggregating data from all phase 4 studies published in February 2024 to identify adverse reactions. These results are categorized by disease state alphabetically, demonstrating the method's capacity to generate structured and easily navigable outputs. The results section is tailored to exemplify the valuable, actionable insights attainable through our workflow. This research emphasizes the game-changing potential of integrating advanced technologies such as ChatGPT into pharmacovigilance, signaling a new era in safeguarding drug safety.

The present study was performed to examine that transforming growth factor beta (TGF-β) in root-surrounding tissues on deciduous teeth during the physiological root resorption regulates the differentiation induction into odontoclast. We prepared root-surrounding tissues with (R) or without (N) physiological root resorption scraped off at three regions (R1-R3 or N1-N3) from the cervical area to the apical area of the tooth and measured both TGF-β and the tartrate-resistant acid phosphatase (TRAP) activities. The TGF-β activity level was increased in N1-N3, whereas the TRAP activity was increased in R2 and R3. In vitro experiments for RANKL-mediated osteoclast differentiation revealed that TGF-β in N1-N3 and R1-R3 enhanced the TRAP activity in RAW264 cells. A genetic study indicated that the mRNA level of TGF-β1 in N1 and N2 was significantly increased, and corresponded with that of osteoprotegerin (OPG). In contrast, the expression level of receptor activator of NF-κB ligand (RANKL) was increased in R2 and R3. Our findings suggest that TGF-β is closely related to the regulation of OPG induction and RANKL-mediated odontoclast differentiation depending on the timing of RANKL and OPG mRNA expression in the root-surrounding tissues of deciduous teeth during physiological root resorption.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Coronavirus disease 2019 (COVID-19) has affected medical practice. More than 7,000,000 patients died worldwide after being infected with COVID-19; however, no specific laboratory markers have yet been established to predict death related to this disease. In contrast, electrocardiographic changes owing to COVID-19 include QT prolongation and ST-T changes; however, there have been no studies on ambulatory electrocardiographic markers of COVID-19. We encountered three patients diagnosed as having COVID-19 who did not have a prior history of significant structural heart diseases. All had abnormalities in ambulatory echocardiogram parameters detected by high-resolution 24-h electrocardiogram monitoring: positive late potentials (LPs) and T-wave alternans (TWA), abnormal heart rate variability (HRV), and heart rate turbulence (HRT). Case 1 involved a 78-year-old woman with a history of chronic kidney disease, Case 2 a 76-year-old man with hypertension and diabetes, and Case 3 a 67-year-old man with renal cancer, lung cancer, and diabetes. None of them had a prior history of significant structural heart disease. Although no significant consistent increases in clinical markers were observed, all three patients died, mainly because of respiratory failure with mild heart failure. LP, TWA, HRV, and HRT were all positive in three cases with no significant structural cardiac disease at the initial phase of admission. There is a possibility that LP, TWA, HRV, and HRT have the potential to be risk stratifiers of COVID-19 pneumonia in the early phase of admission. Further accumulation of data regarding ambulatory electrocardiographic markers in patients with COVID-19 is needed.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

A novel hybrid cobalt phosphite, (H2DAB)[Co(H2PO3)4]·2H2O, has been synthesized by using slow evaporation method, in the presence of cobalt nitrate, phosphorous acid and 1,4- dia-minobutane (DAB= 1,4- diaminobutane) as a structure-directing agent. Single crystal X-ray diffraction analysis showed that the compound crystallizes in the P-1(n.2) triclinic space group, with the following unit cell parameters (Å, °) a = 5.4814 (3), b = 7.5515 (4), c = 10.8548 (6), α = 88.001 (4), β = 88.707 (5), γ = 85.126 (5), and V= 447.33 (4) Å3. The crystal structure was built up from cor-ner-sharing [CoO6] octahedra, forming chains parallel to [001], which are interconnected by H2PO3 pseudo-tetrahedral units. The deprotonated cations, residing between the parallel chains, interacted with the inorganic moiety via hydrogen bonds leading thus to the formation of the 3D crystal structure. The Fourier transform infrared spectrum showed characteristic bands corresponding to the phosphite group and the organic amine. The thermal behavior of the compound consisted mainly of the loss of its organic moiety and the water molecules. The biological tests exhibited significant activity against Candida albicans and Escherichia coli strains in all used concentrations, while less inhibitory activity was pronounced against Staphylococcus epidermidis and Saccharomyces cerevisiae, and in the case of multi-cellular organisms, no activity against the nematode model Steinernema feltiae was detected.

In recent years, the focus of disease resistance and susceptibility studies in cattle have been on determining patterns in the innate immune response of key proteins, such as Toll-like receptors (TLR). In the bovine genome, there are 10 TLR family members and, of these, TLR2, TLR4 and TLR6 are specialized in recognition of bacterial ligands. Indigenous cattle breeds of Anatolia have been reported to show fewer signs of clinical bacterial infections, such as bovine tuberculosis and mastitis, and it is hypothesized that this might be due to a less stringent genetic selection during breeding. In contrast, Holstein-Friesian cattle have been under strong selection for milk production, which may have resulted in greater susceptibility to diseases. To test this hypothesis, we have compared the TLR2, TLR4 and TLR6 genes of Anatolian Black (AB), East Anatolian Red (EAR), South Anatolian Red (SAR), Turkish Grey (TG), and Holstein (HOL) cattle using Next Generation Sequencing. The SAR breed had the most variations overall, followed by EAR, AB, TG and HOL. TG had the most variations for TLR2 whereas SAR had the most variations in TLR4 and TLR6. We compared these variants with those associated with disease and susceptibility traits. We used exon variants to construct haplotypes, investigated shared haplotypes within breeds and determined candidate haplotypes for disease resistance phenotype in Anatolian cattle breeds.

This paper reports design of a 2 × 4 hybrid multimode interferometer-Mach-zehnder interferometer (MMI-MZI) configuration and compact thermo-optical switch consisting of slab waveguides on the silicon-on-insulator (SOI), platform. The device consisted of two identical MMIs as power splitters and couplers that are connected with two identical MMI-based phase shifters, and linear tapers at both ends of the MMIs to minimize the power coupling loss. A thin Al pad is used as a heating element, and a trench is created around this pad to prevent heat from spreading and to minimize loss. The calculated average thermo-optical switching power consumption, excess loss, and power imbalance are 1.4 mW, 0.9 dB, and 0.1 dB, respectively. The overall footprint of the device is 6 × 304 μm². The new heating method has advantages of compact size, ease of fabrication on SOI platform with the current CMOS technology, and offers low excess loss and power consumption as demanded by devices based on SOI technology. The device can act as two independent optical switches in one structure.

PVC items are environmentally friendly as, unlike polyolefins, they are mainly based on chlorine, one of the most abundant elements on earth. However, in the eco-design context, articles' durability plays the crucial role, contributing to the enhancement of their sustainability. In this framework the research on additives capable of increasing the weatherability of outdoor articles is essential. The theory section of the paper reviews the mechanisms of weathering leading to PVC degradation that undermine the durability of items such as window frames or roller shutters. The weathering of PVC items is a complex phenomenon involving photo-chemical and secondary chemical reactions, that yields the formation of conjugated polyene sequences underskin in absence of oxygen and carbonyls in the surface. Here the chain scission of the polymer backbone occurs, bringing the disintegration of the surface of the item and causing the typical discoloration called chalking, especially evident in dark-colored articles. In the experimental section of the paper the effect of different acid scavengers on the item weathering has been studied with natural outdoor and two accelerated exposures, xenon-arc and Q-UV testing devices. Results confirm that some acid scavengers are efficient in preventing chalking, but some are ineffective or even detrimental. Thus, the PVC formulations of durable articles upon weathering still depend on a complex choice of the appropriate ingredients, and several outdoor and indoor accelerated weathering tests are needed to predict the articles' lifetime.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

We investigate, whereas the SU(4)/SU(2) model, is viable for describing strong interactions. The existing problems of confinement and asymptotic freedom, two phenomena that can not be described by the SU(3) model, might indicate that we need something "larger" than the SU(3) model. The considered coset SU(4)/SU(2) or the Stiefel manifold V^2(C_4) contains an su(3) algebra, plus additional degrees of freedom that resembes the Feddev-Poppov concept. The richer structure of this coset, give us enough room, to seek for new phenomena, as its dimensionality is 12. The consideration of the SU(4)/SU(2) model flavors firstly the unification of nuclear fields (strong and weak) in an SU(4) model.

Functional articular cartilage regeneration remains an unmet medical challenge, increasing the interest for innovative biomaterial-based tissue engineering (TE) strategies. Hydrogels, 3D macromolecular networks with hydrophilic groups, present articular cartilage-like features such as high water content and load-bearing capacity. In this study, 3D porous polyethylene glycol diacrylate (PEGDA) hydrogels were fabricated combining the gas foaming technique and an UV-based crosslinking strategy. The 3D porous PEGDA hydrogels were characterized in terms of their physical, structural and mechanical properties. Our results showed that the size of the hydrogels pores can be modulated by varying the initiator concentration. In vitro cytotoxicity tests showed that 3D porous PEGDA hydrogels presented high biocompatibility both with human chondrocytes and osteoblast-like cells. Importantly, the 3D porous PEGDA hydrogels supported the viability and chondrogenic differentiation of human bone marrow-derived mesenchymal stem/stromal cells (hBM-MSCs)-based spheroids as demonstrated by the positive staining of typical cartilage extracellular matrix (ECM) (glycosaminoglycans (GAGs)) and upregulation of chondrogenesis marker genes. Overall, the produced 3D porous PEGDA hydrogels presented cartilage-like mechanical properties and supported MSC-spheroid chondrogenesis, highlighting their potential as suitable scaffolds for cartilage TE or disease modelling strategies.

The ongoing challenge to ensure a sustainable and affordable energy supply forces industrial companies to implement appropriate measures. These measures typically lead to an increased system complexity, which has to be addressed during operation. Whereas existing approaches from the field of supervisory and optimal control appear to be capable of mastering this issue, these are still not adopted in industry. Therefore, this work presents a procedure model for the systematic development of application-oriented operating strategies for industrial energy supply systems. The procedure model combines research approaches from the fields of sequencing control and approximate MPC to extract rule-based operating strategies. By splitting the procedure model into five phases, expert knowledge can be integrated in a target-oriented manner. Subsequently to the description, the procedure model is exemplary applied to the example of an industrial heating supply system. Throughout an optimization study, the developed operating strategy is compared to a MPC strategy as well as a baseline strategy. Whereas the conventional MPC approach is the upper bound with regard to optimality, the developed operating strategy is able to generate comparable results. Compared to the baseline strategy, a relative reduction in operating expenses of 5.4 % to 37.0 % are achieved in this specific use case.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

In this work, pure TiO₂ and nano-magnetic of Fe₃O₄/TiO₂ were synthesized for degradation of 2,4-dichlorophenol (2, 4-DCP) as an organic pollutant. A range of analytical techniques including XRD, DRS, FESEM, and VSM were employed to reveal the crystal structure, morphology and property of the nanocomposite. The XRD results showed the prepared samples including 100% anatase phase. We obtained the band gap energy 2.9 and 2.8 eV for pure TiO₂ and Fe₃O₄/TiO₂ respectively. VSM results demonstrate that easy, fast separation and redispersion of Fe₃O₄/TiO₂ sample can be realized. We obtained 62% and 31% degradation of 2,4-DCP in the presence of Fe₃O₄/TiO₂ and pure TiO₂ under visible light respectively.

We define a spinor-Minkowski metric for SL(4,C). It is not a trivial generalization of the SL(2,C) metric and it involves the Minkowskian one. We define 4x4 version of the Pauli matrices and eight 4-component associated generalized eigenvectors that can be regarded as undotted covariant spinors. The 4-component spinors can be grouped into four categories. Each category transforms in its own way. The outer products of pairwise combinations of 4-component spinors can be associated with 4-vectors. Including the dotted covariant, undotted and dotted contravariant forms totally we have sixteen pairs of spinors. Eight of them live in the conjugate space which has no countepart in SL(2,C).

The rationalization of single molecule magnets’ (SMMs) magnetic properties by quantum mechanical approaches represents a major task in the field of the Molecular Magnetism. The fundamental interpretative key of molecular magnetism is the phenomenological Spin Hamiltonian and the understanding of the role of its different terms by electronic structure calculations is expected to steer the rational design of new and more performing SMMs. This paper deals with the ab initio calculation of isotropic and anisotropic exchange contributions in the Fe(III) dimer [Fe₂(OCH₃)₂(dbm)₄]. This system represents the building block of one of the most studied Single Molecule Magnets ([Fe₄RC(CH₂O)₃)₂(dpm)₆] where R can be an aliphatic chain or a phenyl group just to name the most common functionalization groups) and its relatively reduced size allows the use of a high computational level of theory. Calculations were performed using CASSCF and NEVPT2 approaches on the X-ray geometry as assessment of the computational protocol, which has then be used to evinced the importance of the outer coordination shell nature through organic ligand modelization. Magneto-structural correlations as function of internal degrees of freedom for isotropic and anisotropic exchange contributions are also presented, outlining for the first time the extremely rapidly changing nature of the anisotropic exchange coupling.

By slowly evaporating 4-bromo-2-methylbenzonitrile at room temperature, it was possible to make a single organic nonlinear optical crystal. The grown crystal's crystalline nature was verified, and the unit cell characteristics are provided as a = 4.08Å, b = 6.61 Å, c = 28.93Å, α = 90º, β = 90º, γ = 90º. The functional groups of the crystal produced were identified using the FTIR and FT-Raman spectra. The UV cutoff wavelength is found at 221.6 nm, and the transparency nature of the crystal was analyzed in the optical studies.  The band gap of the grown crystal was estimated using the Taucs’ plot. The violet and red emissions of photoluminescence are discussed. A high dielectric constant was received at a low frequency. The TG/DTA curve shows that the grown crystal was stable up to 125.59 ºC.  The Kurtz-Perry powder technique was applied to confirm the Second Harmonic Generation's (SHG) nature. By using the agar diffusion method, the antibacterial property of the grown 4B2MBN crystal was determined.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

The quinoline derivative, N-(7-chloro-4-morpholinoquinolin-2-yl)benzamide, was synthesized in a conventional three-step procedure from 4,7-dichloroquinoline using N-oxidation reaction/C2-amidation reaction/C4 SNAr reaction sequence. The structure of the compound was fully characterized by FT-IR, 1H‐, 13C-NMR, DEPT-135°, and ESI-MS techniques. Its physicochemical parameters (Lipinski’s descriptors) were also calculated using the online SwissADME database. Such derivatives are relevant therapeutic agents exhibiting potent anticancer, antibacterial, antifungal, and antiparasitic properties.

A conjugate compound 5, (E)-6-hydroxy-2-oxo-2H-chromen-7-yl 3-(4-hydroxy-3-methoxyphenyl)acrylate, of 6,7-hydroxycoumarin (esculetin) 3 and (E)-3-(4-hydroxy-3-methoxyphenyl)- acrylic acid (ferulic acid) 1 was prepared in 61% yield by the esterification reaction of a protected ferulic acid 2a with esculetin 3 in the presence of triethylamine in dichloromethane for 3 h, followed by deprotection using 3M HCl. The structure of compound 5 was confirmed by 1H, 13C NMR spectroscopy, mass-spectrometry and elemental analysis.

Currently, studies are being conducted on the possible role of the cytoprotective effect of biologically active substances in conditions of cerebral hypoxia or cardiomyopathies. At the same time, oxidative stress is considered as one of the important mechanisms of cellular cytotoxicity and a target for the action of cytoprotectors. The aim of this study is to search for derivatives of 3-(arylmethyl)-6-methyl-4-phenylpyridin-2(1H)-ones. The probability of cytoprotective action was assessed by two tests by measuring cell viability (with neutral red dye and MTT test). It was found that some derivatives of 3-(arylmethyl)-6-methyl-4-phenylpyridin-2(1H)-ones under the conditions of our experiment have a pronounced cytoprotective activity, providing better cell survival in vitro, including the MTT test and conditions of blood hyperviscosity. To correlate the obtained results in vitro, molecular docking of the synthesized derivatives was also carried out. The standard drug omeprazole (co-crystallized with the enzyme) was used as a standard. It was shown that all synthesized derivatives of 3-(arylmethyl)-6-methyl-4-phenylpyridin-2(1H)-ones had higher affinity for the selected protein than the standard gastro-cytoprotector omeprazole. The studied derivatives of 3-(arylmethyl)-6-methyl-4-phenylpyridin-2(1H)-ones also fully satisfy Lipinski's rule of thumb of five (RO5), which increases their chances for possible use as orally active drugs with a good ability to absorption and moderate lipophilicity. Thus, the results obtained make it possible to evaluate derivatives of 3-(arylmethyl)-6-methyl-4-phenylpyridin-2(1H)-ones as having a relatively high cytoprotective potential.

The 5-hydroxymethylfurfural (HMF) is a six-carbon heterocyclic organic compound with two substituents an aldehyde group and an alcohol group. It is formed from saccharides as a result of two reactions: the Maillard reaction and the caramelization of saccharides. It has both a negative and a positive effect on the human body, which makes it, even more, an attractive research object. The objective of the study was to determine HMF content in honey samples available on the Polish market using three varied methods and compare the results obtained. The methodology used included: two spectrophotometric methods (by White and Winkler) and the HMF determination method based on the LC-MS/MS technique developed uniquely for this study. The determined HMF content in all tested honey samples did not exceed the applicable standard. All results are within the scope of the European Council Directive 2001/110/EC of 20 December 2001, i.e. they do not exceed HMF content in honey, which is 40 mg/kg.

Postprandial glucose levels between 4 and 7.9 hours (PPG4–7.9h) correlate with mortality from various diseases including hypertension, diabetes, cardiovascular disease, and cancer. This study aimed to assess if predicted PPG4–7.9h could diagnose diabetes. Two groups of participants were involved: Group 1 (4420 participants) had actual PPG4–7.9h, while Group 2 (8422 participants) lacked this measure but had all the diabetes diagnostic measures. Group 1 underwent multiple linear regression to predict PPG4–7.9h using 30 predictors, achieving accuracy within 11.1 mg/dL in 80% of the participants. Group 2 had PPG4–7.9h predicted using this model. Receiver operating characteristic curve analysis showed that predicted PPG4–7.9h could diagnose diabetes with an accuracy of 87.3% in Group 2, with a sensitivity of 75.1% and specificity of 84.1% at the optimal cutoff of 102.5 mg/dL. Simulation on 10,000 random samples from Group 2 revealed that 175 participants may be needed to investigate PPG4–7.9h as a diabetes diagnostic marker with a power of at least 80%. In conclusion, predicted PPG4–7.9h appears to be a promising diagnostic indicator for diabetes. Future studies seeking to ascertain its definitive diagnostic value might require a minimum sample size of 175 participants.

Paratuberculosis, or Johne's disease, caused by Mycobacterium avium subsp. paratuberculosis (MAP), is a chronic granulomatous enteritis affecting both domestic and wild ruminants. The agent was also found in wild mammals such as wild boar (Sus scrofa), however, the role of wild mammals in the epidemiology of MAP is unclear. During the research period, 941 free-ranging wild boar (S. scrofa) legally hunted in two locations in the Centre-eastern region of Portugal were examined. Ninety-seven wild boar exhibited one or more gross lesions and were tested for the presence of Mycobacterium avium subsp. paratuberculosis using acid-fast staining, mycobacterial culture, poly-merase chain reaction (PCR), and histopathological examination. Forty-five animals (46.4%, 95% CI: 36.5-56.3%) were identified as infected, as indicated by positive results in culture and/or PCR. The findings revealed that the most significant risk factor was being a juvenile compared to year-lings and adults (OR = 10.2, 95% CI: 2.2-48.0). Based on our results, 37.9% (n = 11) of the infected animals were considered suitable for human consumption. Our findings offer novel insights into mycobacterial infections in wild boar populations in Portugal and suggest that wild boar could be a source of human infection if zoonotic potential is considered.

Introduction The monitoring of cerebral perfusion in patients with brain damage is a major clinical challenge. Monitoring cerebral oxygenation (rSO2) by NIRS was introduced at the turn of the 1980s, and many clinicians believed it was a valuable method for assessing cerebral perfusion and subsequent measures to optimize cerebral flow. The main problem of NIRS usage is the presence of the intermediate structures-skin, skull, meninges, cerebrospinal fluid-and their influence on the outcome of the test. Therefore, it seems that NIRS assessment performed on a patient during brain death attempts, can give an idea of the magnitude of the influence of these intermediate structures on the monitoring result. Case We present a retrospective analysis of cerebral oxygenation measurements of a patient undergoing a brain death diagnostic procedure. A clinical situation where the cerebral blood flow is stopped can give an idea of the specificity of the method, particularly the impact of the influence of intermediate structures on the monitoring outcome. In this case, the NIRS result is increased by the oxygenation of the patient before the apnoea test. The influence of chromophores in the tissues surrounding the CNS, reflections and scattering of the light wave spectrum have a very significant effect on the final result of cerebral saturation measurement. Discussion The majority of research observations describing changes in cerebral perfusion or its optimisation may be burdened by the problem described, i.e. the significant influence of measured oxygenation from intermediate structures. The specificity of NIRS to assess cerebral perfusion requires careful analysis. The therapeutic implications of monitoring cerebral oxygenation with NIRS are of great importance and, from the example presented and the literature provided, the method should be used with caution. It has been shown that in a patient with brain death, the result of NIRS oxygenation measurements depends on the surrounding structures of the brain.

In the British setting, the deployment of the phrase ‘doing god’ has become increasingly common to refer to an emerging trend whereby religion has acquired an increasingly prominent role in political spaces and discourses. This was particularly prominent while David Cameron was Prime Minister and leader of the Conservative Party. While historically, religion has not had a prominent place in either the former Prime Minister David Cameron. Here, the findings from critical analyzing a series of Cameron’s public pronouncements about religion—and Christianity in particular—is set out to try and better understand his own adherence to Christianity (the personal) how this intersected with his politics and role as Prime Minister (the political), and more importantly how this shaped his views about Britain being a Christian country (the national). Contextualised within the embryonic scholarly literature relating to the phenomenon of ‘doing god’ in the contemporary British setting, this article concludes by considering alternative and analogous frames through which greater elucidation of the true motivations of his pronouncements might be understood.

Accompanied by increasing population growth and urban sprawl, most coastal cities are unprecedentedly vulnerable to climate change and its impacts, such as sea level rise, increasing extreme storm events, and coastal flooding. Coastal resilience and sustainable development are antidotes to vulnerability; they aim to enhance the adaptive capability of absorbing disturbances and resisting uncertainty. This study explores building a quantitative assessment framework to measure resilience and provide an objective and comparable method to understand the strengths and weaknesses in a given region. The proposed 25 resilience indicators incorporate the aspects of essential livelihood protection, infrastructure and natural resource maintenance, emergency facilities and institutions, floodplain management regulations, and adaptive planning process. Each indicator is assigned the resilience quality that includes robustness, resourcefulness, redundancy, and rapidity. The aggregated resilience quality scoring reflects the systematic performance of the city to cope with the coastal hazards. The innovative part of this framework is combining hazard mitigation measures, climate adaptation strategies, and sustainable development goals together to achieve a comprehensive assessment method. In the case of New Haven, the resilience assessment is taken as a practical monitoring tool and decision-making support.

The study of precipitation amount at different time scales constitutes an important issue in climate research and risk assessment. When dealing with daily totals, a frequent but sometimes underestimated problem is at what time the observation day begins. The choice of different starting times may lead to incompatibility between stations and incorrect identification of extreme events. In this work, the problem of temporal misalignment between precipitation datasets characterized by different starting time of the observation day is analyzed. The most widely used adjustment methods (1day and uniform shift) and two methods based on reanalysis (NOAA and ERA5) are evaluated in terms of temporal alignment, precipitation statistics and percentile distributions. As test series, the precipitation amount collected from 9 a.m. local time (09 LT) on the previous day to 09 LT on the target day (9-9 datasets) of the Padua and nearby stations in the period 1993-2022 have been selected. Results show that the reanalysis-based methods, in particular ERA5, outperform the others in temporal alignment, regardless the station. But, for the periods in which reanalysis data are not available, “1day” method, which shifts the daily amount back one calendar day, and “unif” method, which distributes uniformly the daily total from a 2-day moving window surrounding the target date, can be considered valid alternatives. On the other side, concerning the precipitation statistics, the reanalysis-based methods are not the best option, as they increase the precipitation frequency and reduce the mean value over wet days, NOAA much more than ERA5. Nevertheless, the uniform method provides a larger deviation from the original daily series. The use of the series of a station nearby the target one, which is mandatory in case of missing data, gives similar or better results than applying any adjustment method to the 9-9 series. General conclusions can hardly be drawn as they depend on the method and station. For the Padua dataset, the analysis was repeated at monthly and seasonal resolution. In general, the adjustment series show the most relevant changes in the precipitation statistics in summer and less temporal alignment with the original series in summer and autumn, the two seasons mainly affected by heavy rains in Padua. Finally, the percentiles distribution, analyzed for all the methods and stations, indicates that any adjustment method underestimates the percentile values, except ERA5. Only Legnaro, the station most correlated with Padua, gives results like ERA5.

Hydrological processes are complex to compute on hilly areas when compared to the plain areas. Most of the hydrological model do not take into account the critical rainfall-runoff generation processes such as subsurface storm flow, saturation excess flow, overland flow, return flow and pipe storage. The simulations of the above processes in the soil matrix requires detailed hillslope hydrological modelling. In present study, a hillslope experimental plot is designed to study the runoff generation processes on the plot scale. The setup is designed keeping in view the natural hillslope conditions prevailing in the north western Himalayas, India where high intensity storm event occurs frequently. Using the experimental data and the developed conceptual model, the overland flow and the subsurface flow through macropore dominated area has been estimated/analyzed on the pixel basis. Over the experimental hillslope plot, a rainfall simulator was installed to generate the rainfall intensity in the range of 15 to 150 mm/hr which represented the dominating rainfall intensity range in the region. Soil moisture sensors were also installed at 100 mm and 300 mm depth at different locations of the plot to observe soil moisture variations. It was found that once the soil is saturated, it remains in the field capacity for next 24-36 hours. Such antecedent moisture conditions are most favorable for the generation of rapid stormflow from hillslopes. Dye infiltration test was also performed on the undisturbed soil column to observe the macropore fraction variability over the vegetated hillslopes. The surface runoff predicted using the developed hillslope hydrological model compared well with the observed surface runoff under high intensity rainfall conditions.

The creation of the National Muslims Women’s Advisory Group (NMWAG) in 2008 by Britain’s New Labour Government was part of a strategy which sought to engage different levels of Muslim communities beneath an overarching focus on reducing ‘Islamic extremism’. To do so however, Government acknowledged that it would need to support Muslim women to overcome some of the constraints it believed were placed on Muslim women in contemporary Britain. Deeming theology and religious interpretation to be one of those constraints, Government saw the need to empower Muslim women to ‘influence and challenge’ religious and theological discourses as a priority. This article therefore offers a case study on a project that was commissioned by Government that sought to empower Muslim women to ‘influence and challenge’ theological interpretations in collaboration with the NMWAG. Having gained unprecedented access to the NMWAG, its activities and engagement with Government, this article presents previously unpublished findings from that project to focus on two key themes: Muslim women, their identity and position; and theology, leadership and the participation of women. Having explored these in detail, this article concludes by critically reflecting on the way in which Government engaged and interacted with Muslim women, the role and relative success of the NMWAG and, most importantly, the extent to which the NMWAG was able to ‘influence and challenge’ interpretations of Islamic theology.

Quantum correlations, especially time correlations, are crucial in ghost imaging in order to significantly reduce the background noise on the one hand while increasing the imaging resolution. Moreover, the time correlations serve as a critical reference, distinguishing between signal and noise, which in turn enable clear visualization of biological samples. Quantum imaging also addresses the challenge involved in imaging delicate biological structures with minimal photon exposure and sample damage. Here we explore the recent progress in quantum correlation-based imaging, notably its impact on secure imaging and remote sensing protocols as well as on biological imaging. We also exploit the quantum characteristics of heralded single-photon sources (HSPS) combined with decoy-state methods for secure imaging. This method uses Quantum Key Distribution (QKD) principles to reduce measurement uncertainties and protect data integrity. It is highly effective in low-photon-number regimes for producing high-quality, noise-reduced images. The versatility of decoy-state methods with WCSs (WCS) is also discussed, highlighting their suitability for scenarios requiring higher photon numbers. We emphasize the dual advantages of these techniques: improving image quality through noise reduction and enhancing data security with quantum encryption, suggesting significant potential for quantum imaging in various applications, from delicate biological imaging to secure quantum communication.

An oxidation resistant coating on cemented tungsten carbides is characterised in this work. Cemented tungsten carbides (cWCs) are routinely used in mining and manufacturing but are also candidate materials for compact radiation shielding in fusion power generation. In both environments, cWCs will suffer significant degradation due to oxidation at relatively low temperatures. In a recent study, a Si-deposition coating method was demonstrated to improve the oxidation resistance of cWCs by up to a factor of 1,000. This work focusses on the growth kinetics, phase composition, and mechanical properties of these coatings. By combining quantitative X-ray diffraction, electron microscopy and nanoindentation, we show that the coating layer has a 20 % higher hardness than the substrate, which was explained on the basis of a previously-unknown presence of a fine distribution of very hard SiC laths. To interpret the coating stability, a coating growth map is developed. The map shows the structure is stable under a broad range of processing temperatures and composite compositions, demonstrating the potential application of these coatings in a variety of nuclear shielding cWCs.

Reverse engineering is applied to identify optimum polymerization conditions for the synthesis of polymer with pre-defined properties. The proposed approach uses multi-objective optimization (MOO) and provides multiple candidate polymerization procedures to reach the targeted polymer property. The objectives for optimization include maximal similarity of molar mass distributions (MMD) compared to the target MMD, minimal reaction time, and maximal monomer conversion. The method is tested for vinyl acetate radical polymerizations and can be adopted to other monomers. The data for the optimization procedure is generated by an in-house developed kinetic Monte-Carlo (kMC) simulator for a selected recipe search space. The proposed reverse engineering algorithm comprises several steps: kMC simulations for the selected recipe search space to derive initial data, performing MOO for a targeted MMD, and identification of the Pareto optimal space. The last step uses a weighted sum optimization function to calculate the weighted score of each candidate polymerization conditions. To decrease the execution time clustering of the search space based on MMDs is applied. The performance of the proposed approach was tested for various target MMDs. The suggested MOO-based reverse engineering provides multiple recipe candidates depending on competing objectives.

Solar radiation is the main energy source for mankind and an accurate data of solar radiation levels for a particular location is vital for the optimum operation of solar energy transducers such as photovoltaic cells and solar thermal collectors. In this work, we show that there is a linear relationship between recorded monthly average temperatures and solar radiation in Swaziland. The correlation can be utilized to develop two mathematical models for the estimation of solar radiation: one from the measured monthly average temperatures and the other based on the square-root of the difference between measured maximum and minimum monthly average temperatures. Both models fit the data well and can be applied to estimate solar radiation in other parts of the region.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

Herein, two title compounds, N-Benzoyl-N’-4-cyanophenyl thiourea (I) and N-(4-nitrobenzoyl)-N’-4-cyanophenyl thiourea (II) were synthesized in high yield, via aroyl isocyanate and 4-aminobenzonitrile. The structure of the prepared compounds was characterized by elementary analysis and FT-IR, ¹H, ¹³C NMR spectroscopic methods. Cyclic voltammetric (CV) experiments were performed with glassy carbon electrode. The reduction potential values of different functional group such as nitro, cyano in title compounds were investigated using CV curves.

In the article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal aging after so-lution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC), and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) during cooling (from +1500C to -500C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20 and 100 hours at 500°C; (2) during heating (from -500C to +1500C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19’) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time, (4) the width of the total temperature range of the transformation M(B19’)  A(B2) during heating changes from large (∆T=49,7°C), after solution annealing, to narrow (∆T=19.3°C and ∆T=17.9°C after 20 h and 100 h of ageing) and, most importantly, (5) a comparison with literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of the fact whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite  austenite transformation in the same temperature range.