Variations in threshold voltage (VTH) and charge distributions in noncircular cells of three-dimensional (3D) NAND flash memory are investigated. The electric field difference in the circular and spike regions causes nonuniform trapped electron density in the charge trap layer (CTL) and influences the VTH variation. Such less-trapped electron (LT) regions in CTL between the circular and spike regions exhibit a lower electric field during the program, resulting in a higher current flow through that region. For the two-spike cells, the charge distribution and VTH variation are analyzed at different heights (HSpike) and angles between spikes. These irregular cells decrease VTH as the HSpike increases.

The effects of residual stress in a tungsten gate on a polysilicon channel in scaled 3D NAND flash memories were investigated using a technology computer-aided design simulation. The NAND strings with respect to the distance from the tungsten slit were also analyzed. The scaling of the spacer thickness and hole diameter induced compressive stress on the polysilicon channel. Moreover, the residual stress of polysilicon in the string near the tungsten slit had greater compressive stress than the string farther away. The increase in compressive stress in the polysilicon channel degraded the Bit-Line current (Ion) because of stress-induced electron mobility deterioration. Moreover, a threshold voltage shift (△Vth) occurred in the negative direction because of conduction band lowering.

This paper is an extended version of a previously reported conference paper regarding low power design for NAND Flash. As the number of bits per NAND Flash die increases with cost scaling, IO datapath speed increases to minimize the page access time with scaled CMOS in IOs. The power supply for IO buffers, namely VDDQ, has decreased from 3V to 1.2V, accordingly. In this paper, how a reduction in VDDQ can contribute to power reduction in BL path is discussed and validated. Conventionally, BL voltage of about 0.5V has been supplied from a supply voltage source (VDD) of 3V. BL path power can be reduced by a factor of VDDQ to VDD when BL voltage is supplied from VDDQ. To maintain a sense margin at sense amplifiers, the supply source for BLs is switched from VDDQ to VDD before sensing. As a result, power reduction and equivalent sense margin can be realized at the same time. The overhead of implementing this operation is an increase in BL access time of about 2% for switching the power supply from VDDQ to VDD and an increase in die size of about 0.01% for adding the switching circuit, both of which are not significant in comparison with a significant power reduction in BL path power of NAND die of about 60%. The BL path was designed in 180nm CMOS to validate the design. When the cost for powering SSD becomes quite significant especially for data center, an additional lower voltage supply such as 0.8V dedicated to BL charging for read and program verify operations may be the best option for the future.

We discuss a topological method of storing and retrieving information from flash memory. We first present a sensing method where the threshold voltage level, as represented by a sensing time, is extracted in one sensing cycle. The sense time distribution from one set of flash cells, e.g. one physical row, is then processed in software to decode the digital state of each cell. The decoding method uses topological constraints but no rigid or predetermined voltage thresholds to digitize the distribution. The software defined nature of the topologically defined flash (TDF) allows greater flexibility for allocating cells to arbitrary number of digital states.

We propose that a dietary reduction of Lipopolysaccharide (LPS) could reduce risk and slow the progression of cognitive decline and Alzheimer’s disease. LPS is a component of the highly inflammatory cell membrane of Gram-negative bacteria. The highest dietary sources of LPS are processed meat and dairy products, which can sharply raise plasma LPS within one to two hours. The LPS in these foods is packaged into chylomicrons, which enter the bloodstream. Smaller amounts of LPS from colonic microbiota do not account for the sharp postprandial increase of plasma LPS. Once in the bloodstream, LPS can trigger the release of inflammatory cytokines within three hours. LPS can increase cytokines via LPS binding protein and cluster of differentiation-14, triggering toll-like receptor-4, and activating nuclear factor kappa-B. Nuclear factor kappa-B can increase cytokine levels, including interleukin-1-beta, interleukin-6, and tumor necrosis factor-alpha. LPS and inflammatory cytokines are higher in Alzheimer’s disease, both in plasma and in the central nervous system. These cytokines can enter the brain via active transport and induce microglial activation and inflammatory damage in the brain, including loss of synapses and neurons. Elevated brain inflammation from dietary LPS can contribute to cognitive impairment and increased risk of dementia.

In this paper, we aim to present real implementation cases where non-visible elements of environmental impact assessments (EIA), wind flow, are visualized using a 3D digital twin technology. The conventional EIA process serves as a crucial tool in the evaluation of potential environmental impacts prior to the initiation of development projects. This evaluation helps to establish a legal and institutional framework that seeks to minimize the adverse effects on the environment. However, traditional EIA methods present challenges, particularly for non-experts, in comprehending the results of assessments involving non-visible environmental factors such as noise, air quality, and wind flow. These elements are often represented in static images or numerical tables, limiting accurate understanding and engagement. Our proposed method, termed Digital Twin based EIA, addresses these limitations by leveraging digital twin technology. This advanced methodology allows for the visualization of non-visible environmental elements in a spatio-temporal dimension, providing a more interactive and comprehensive user interface/experience for both citizens and stakeholders. In this context, we present a unique case study that focuses on visualizing wind flow using this technology. This paper serves as an example of how digital twin platforms can enhance traditional EIA processes, offering a more immersive and informative experience. The evolution of EIA into the digital realm signifies an important step forward in fostering public understanding and engagement in environmental protection efforts.

Counterfeiting electronic components is a serious problem for the security and reliability of any electronic systems. Unfortunately, the number of counterfeit components has increased considerably after the introduction of horizontal semiconductor supply chain. In this paper, we propose a new method for detecting recycled Flash memory, a major target of the counterfeiters due to its ubiquitous usage. Proposed method is based on measurement of change in Flash array characteristics (such as erase time, program time, fail bit count, etc.) with its usage. We find that erase time is the best metric to distinguish a used Flash chip from a fresh one for the following reasons: (1) erase time shows minimal variation among different fresh memory blocks/chip and (2) erase time increases significantly with usage. We verify our method for a wide range of commercial off the shelf Flash chips from several vendors, technology nodes, storage density and storage type (single-bit per cell and multi-bit per cell). The minimum detectable chip usage varies from 0.05% to 3.0% of its total lifetime depending on the exact details of the chip.

Diseases in articular cartilages have affected millions of people globally. Although the biochemical and cellular composition of articular cartilages is relatively simple, there is the limitation in self-repair ability of cartilage. Therefore, developing the strategies for cartilage repair is very important. Here, we reported a new manufacturing process of water-based polyurethane based photosensitive materials with hyaluronic acid and applied the materials for 3D printed customized cartilage scaffolds. The scaffold has high cytocompatibility and is one that closely mimics the mechanical properties of articular cartilages. It is suitable for culturing human Wharton's jelly mesenchymal stem cells (hWJMSCs) and the cells showed an excellent chondrogenic differentiation capacity. We consider that the 3D printing hybrid scaffolds may have potential in customized tissue engineering and facilitate the development of cartilage tissue engineering.

Literature reported the insulin is an important for the humans and it is secreted in the pancreas and controls, regulates the glucose level. It also controls the mechanism and growth. On decreasing the amount of insulin can caused diabetes, several cancers and other disease. Therefore, there is a need to find promising candidates can binds with insulin and stabilize them. Organic compounds containing hetero atoms have lots of biological potency in different area, therefore, researchers are designing new biological potent compounds. Further, insilico studies attracted the researchers in last one decade mainly to get the drug in less time with a clear strategy. In the present work, authors have designed two types of conjugates, xanthenes with trizole as well benzisoxazole and study their interaction with the insulin using computational methods. The library of compounds was screened through molecules docking in terms of binding energy between the designed compound and the active site of the receptor. Further, their ADME properties are investigated. CMPD19 showed best binding affinity with the insulin and may be considered as oral drug based on the bioactive scores.

The research aims to present an innovative methodology to execute the Heritage conservation processes in a collaborative and interdisciplinary BIM project, with an effective management of the deterioration suffered over time, emphasizing the structures and coatings. The research begins with the architectural survey using scanning techniques (TLS) and terrestrial photogrammetry (SfM) and taking as a study the Duomo of Molfetta (Italy), a unique Romanesque architecture of Puglia (Italy). The methodological process is mainly aided by the precise semantic segmentation of global point clouds, a semi-automatic process assisted by classification algorithms implemented in the post-processing software, and which has allowed the classification of the unstructured information provided by the remote sensing equipment when identifying the architectural-structural systems of a building with high historical values. Subsequently, it has been possible to develop an efficient Scan-to-HBIM workflow, where the Heritage-BIM (HBIM) project has fulfilled the function of a database by incorporating and organizing all the information (graphic and non-graphic) to optimize the tasks of auscultation, identification, classification, quantification and, in turn, facilitating the parametric modeling of unique structures and architectural elements. The results have shown great effectiveness in the processes of characterization of architectural and artistic heritage, focusing on the deformations and deterioration of the masonry in columns, and making multidisciplinary conservation work in an HBIM project more flexible. But there are still some difficulties for the automatic interpretation of 3D point cloud data, related to specific systems of the historical architecture. In conclusion, human action and interpretation continues to be a fundamental pillar to achieve precise results in a heritage environment.

Alcohol use disorder (AUD) is a chronic and relapsing biopsychosocial condition that leads to a wide range of medical, psychological, social, economic, and personal issues. The study investigated the predictors of quality of life (QoL) among male patients seeking treatment for AUD based on attention, cognitive instability, motor impulsiveness, perseverance, and self-control dimensions of trait impulsivity. The study also investigated the potential mediating effect of anxiety and alcohol use severity in this relationship. After an initial assessment, participants underwent comprehensive evaluations, including sociodemographic data, clinical history, and QoL domains. Evaluations also covered AUD severity, impulsivity dimensions, cognitive functions, craving intensity, depression, anxiety and self-efficacy. Multiple linear regressions were employed to identify associations between independent variables and QoL. Attention dimension of impulsivity and anxiety symptoms significantly predicted physical health QoL. Self-control dimension and severity of alcohol use disorder predicted psychological QoL. Indirect effect of attention dimension on physical health was significant [effect =-1.082,95% CI (-2.008, -0.3598)].The significance of impulsivity in influencing QoL for individuals with AUD has profound clinical implications. These findings underscore the importance of addressing anxiety and impulsivity in managing AUD, given their considerable impact, particularly on QoL, ultimately shaping treatment outcomes.

Global environmental sustainability is a crucial issue, and Zambia, like many other countries, has particular potential and challenges in this regard. Environmental sustainability has been and is today a priority on the global development agenda due to serious issues emerging from extensive interference with human-related activities. Maintaining environmental sustainability is essential for preserving the nation's natural resources, fostering economic growth, and guaranteeing the welfare of its citizens. Even if there are many significant challenges, coordinated initiatives incorporating international cooperation, sustainable practices, and community engagement can open the door to a more sustainable future. While the ongoing discussion about environmental sustainability takes very diverse forms and concentrate on various aspects of the problem, this paper aims to discuss climate change, habitat and biodiversity, land degradation and agricultural constraints in the Zambian context. Using desktop approach, the paper will utilize reports, academic journals and policy documents in an attempt to define a common starting point from which to gain an understanding of the magnitude of the issue.

The rapid growth of Artificial Intelligence (AI) has led to considerable progress in Automated Fact Verification (AFV). This process involves collecting evidence for a statement, assessing its relevance, and predicting its accuracy. Recently, research has begun to explore automatic explanations as an integral part of the accuracy analysis process. However, the explainability within AFV is lagging compared to the wider field of explainable AI (XAI), which aims at making AI decisions more transparent. This study looks at the notion of explainability as a topic in the field of XAI, with a focus on how it applies to the specific task of Automatic Fact Verification. It examines the explainability of AFV, taking into account architectural, methodological, and dataset-related elements, with the aim of making AI more comprehensible and acceptable to the general society. Although there is a general consensus on the need for AI systems to be explainable, there a dearth of systems and processes to achieve it. In this research, we investigate the concept of explainable AI in general and demonstrate its various aspects through the particular task of Automated Fact Verification. We explore topic of faithfulness in the context of local and global explainability and how these correspond with architectural, methodological and data-based ways of achieving it. We examine these concepts for the specific case of AFV and analyze the current datasets used for AFV and how they can be adapted to further the identified aims on XAI. The paper concludes by highlighting the gaps and limitations in current data science practices and possible recommendations for modifications in architectural and data curation processes that would further the goals of XAI.

Transportation contributes significantly to greenhouse gas emissions, with electrification offering a promising solution. This study evaluates the degradation of State of Health (SOH) over 2.5 years for electrified buses under different charging protocols: DC Fast charging and Flash charging. The vehicles’ models, charging protocols, and financial implications are discussed. High-level simulations reveal that after 2.5 years, the Flash charging vehicle’s SOH reaches 88.93%, while the DC fast charging vehicle reaches 89.46%, showing a 0.47% difference. This slight variance is attributed to Flash charging vehicles avoiding full charge/discharge cycles, reducing battery aging impact. Considering this minimal SOH degradation difference, the choice between DC Fast charging and Flash charging primarily hinges on capital expenditure disparities. Flash charging, with its lower initial battery capacity and reduced capital costs, presents a compelling alternative for city busoperators seeking to electrify their fleets.

This paper illustrates an experimental activity for the closed-loop position control of an actuator made using shape memory alloy (SMA) wire. A solution with the self-sensing effect was implemented to miniaturize the systems, i.e., without external sensors. A proportional control algorithm was initially used, demonstrating the idea's feasibility: the wire can behave simultaneously as an actuator and sensor. An experimental investigation was subsequently conducted for the optimization of the developed actuator. As for the material, a Flexinol wire, Ni-Ti alloy, with a diameter of 0.150 mm and a length of 200 mm, was used. Preliminarily, a characterization of the SMA wire at constant and variable loads was carried out: the characteristics detected are elongation vs. electric current and elongation vs. electrical resistance. The control system is PC-based with a data acquisition card (DAQ). A drive board has been designed and built to read the wire's electrical resistance and power it by pulse width modulation (PWM). A notable result is that the actuator works with good precision and in dynamic conditions, even when it is called to support a load up to 65% different from that for which the electrical resistance-length correlation has previously been experimentally obtained, on which the control is based. This opens up the possibility of using the actuator in a counteracting configuration with a spring, which makes hardware implementation and control management simple.

In this paper, a thermodynamic investigation is done on a Kalina-flash cycle. This work is initially validated with the Kalina cycle power plant, Wich is commissioned in Husavic. Low-temperature Kalina-flash is considered for this study. This cycle is working with the ammonia-water mixture. The Kalina-flash cycle was optimized in the view of exergy and thermal efficiency. A multi-objective genetic algorithm is used to accomplish optimization. The optimum values of the objective functions are observed to be 40.20 and 11.70% respectively. At last, The influence of the separator inlet dryness fraction, basic ammonia mass fraction, temperature and flash pressure ratio on the first and second law efficiencies are analysed.

Advances in computing technology provide an opportunity to grow and develop an effective crop protection system. This study is a new way of diagnosing plant diseases using a deep and convolutional neural network. Deep learning is the strengthened method of machine learning. It uses a neural network that imitates like a human brain and gains certain information. Although powerful, its training process necessitates millions of tagged data points. The study's Methodology consists of three key stages: data acquisition, pre-processing, and Model Building.

In recent years, due to the detrimental impact of traditional gas-liquid refrigerants on the environment, the pursuit of solid-state refrigeration technology based on elastocaloric effect, as a promising sustainable alternative, has been promoted. However, the traditional trial-and-error method is inefficient and difficult to meet the material application requirements. In this work, machine learning (ML) was employed to accelerate the development of NiTi-based shape memory alloy (SMA) with excellent elastocaloric effect. By means of active learning, we identified 9 novel NiTi-based SMAs in four iterations, the phase transformation-induced entropy change (ΔS) of which are as high as over 90 J/kg·K-1. Moreover, the model exhibits good interpretability, allowing us to understand the relevance between the target and features from the aspect of mechanism.

Background: People with Down syndrome (DS) have a trisomy of chromosome 21 and marked deficits in verbal memory but relatively preserved visuospatial perception. Verbal memories are related to semantic knowledge. Little is known about the organization of semantic knowledge in people with DS, which was the aim of this study. Aims: The extent of false memory in people with DS was examined. Possible differences in the number of false memories induced by nominal and verbal themes were examined. Methods and Procedures: In the study phase, ten word lists with semantically related associates were presented. In the recognition phase, participants made judgments on whether each word had been represented previously as semantically related lures, old words, and semantically unrelated new words. Outcomes and Results: Differences in the processing of nominal and verbal theme-related lures were observed among people with DS. When processing nominal theme-related lures, people with DS showed delayed false positives. When processing verbal theme-related lures, people with DS showed no differences compared to controls. Similar patterns have been observed in people with DS when processing nominal theme-related associates and verbal theme-related associates. People with DS have delayed recognition of associates. When processing unrelated words, they showed significantly higher false positives than controls for both nominal and verbal eliciting themes. Further analyses of the themes revealed differences in false positives across syntactic categories among groups. Conclusions and Implications: People with DS showed a delayed recognition of associates and deviance in recognizing unrelated words in the nominal and verbal theme categories. People with DS were delayed in terms of nouns, but deviated with verbs in associated and unrelated words. Additionally, people with DS showed distinct patterns in processing five nominal lures and three verbal lures, suggesting that they formed false memories differently based on distinct syntactic categories. Thus, it was concluded that people with DS develop a deviant semantic structure. Category-based interventions for people with DS should be implemented in order to improve their semantic knowledge through lexical connections.

FLASH-RT represents a novel therapeutic radiation modality that holds remarkable potential for mitigating radiation therapy’s adverse side effects. This cutting-edge technology allows for the sparing of healthy tissue while precisely targeting cancerous cells by administering an ultra-high dose-rates of typically between 10 and 30 Gy in less than a few hundred milliseconds. FLASH-RT has demonstrated impressive results in small-animal models, prompting scientists to adapt and advance existing technologies to make it a viable treatment option for humans. However, producing the ultra-high-dose-rate radiation required for the therapy remains a significant challenge. Several radiation sources, such as very high energy electrons (VHEEs), low energy electrons, x-rays, and protons, have been studied for their ability to deliver the necessary dose. Among them, FLASH-x-ray has gained the most attention owing to its capacity to penetrate deeply seated tumours. Despite the complexity of the process, the potential advantages of FLASH-RT make it an exciting area of research. To achieve the FLASH effect, high-frequency, pulsed irradiated accelerator technology can be employed. Sparing healthy tissue, it may allow for more aggressive and effective cancer treatments, leading to a better quality of life for patients. Ongoing research and development will be necessary to refine and optimize this approach to radiation therapy.

During the last few years, the world witnessed one of the worst calamities to humankind- the COVID-19 pandemic. We also witnessed the development of vaccines at an unprecedented pace against the SARS-CoV-2- the causative agent. India was among the hard-hit countries by COVID-19, developed its indigenous vaccine and implemented vaccines developed in other countries as well. Initially, the antibody level and the neutralizing antibody titer against the pathogen were considered as the correlates of immune protection from the disease. However, the long-term protection from the pathogen was provided by the immune memory cells viz. T and B memory cells and their ability to efficiently make recall responses. In this regard, globally the research studies focused mainly on the mRNA-based vaccines. The studies on immune memory response, particularly- the B cell memory response bestowed by the vaccines given to Indians is relatively obscure. We studied the level of RBD specific memory B cells in the peripheral circulation of the study participants and the ability of B cells to secrete antigen-specific antibodies among Indians vaccinated with Covaxin (BBV152), Covishield (AZD1222), Corbevax (BECOV2D) and Sputnik Light (Gam-COVID-Vac) as well as unvaccinated individuals. Our study revealed that Corbevax and Sputnik Light conferred better antibody-secreting cell (ASC) responses.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

This paper presents the novel development of a shape memory polymer foam based on polymer-polymer nanocomposites. Herein, polylactide (PLA)/biosourced polyamide (PA) foams are fabricated by in-situ fibrillation of polymer blends and subsequent supercritical CO2 foaming technique. In this system, PLA serves as a shape memory polymer to endow this foam with a shape memory effect (SME), and in-situ generated PA nanofibers are employed to reinforce the PLA cell walls and provide an additional permanent phase. Concentration of PA, 5 wt.%, is chosen to form an entangled nanofibrillar network. Foams of PLA/PA nanoblends with the same content of constituents are fabricated to reveal the effect of minor phase morphology on the cell structure and shape memory behavior of polymer foams. Profiting from the reinforcing effect of PA nanofibers, the PLA/PA nanocomposite foam exhibits smaller foam cells, a narrower cell size distribution and a comparable cell concentration than the PLA/PA nanoblend foam. In addition, PA nanofibers, unlike PA nanodroplets, favor the shape fixation ratio and recovery ratio and shorten the shape recovery time.

Graph visualization has evolved significantly over time, offering various methods to effectively represent complex data structures. This study introduces a novel force-directed algorithm for 3D data visualization, specifically tailored for commonly used datasets in linked data visualization. Leveraging the power of graph theory and methods, the algorithm aims to address the challenge of creating visually appealing and easily interpretable visualizations, which often necessitate advanced user interaction. By utilizing 3D space and the Unity Engine, the research successfully visualizes data and develops interactive visualizations, overcoming limitations of basic force-directed implementations. The main contribution of presented research is in the force-directed algorithm with springs and controlled placement as a visualization technique that combines the use of springs and attractive forces to stabilize a graph in a 3D environment. The combination of these two techniques also helps prevent the formation of a single large cluster within the graph, enhancing the overall visualization quality.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

This research focuses on the use of the HEC-RAS model to estimate flash flood risk. It combines advanced hydraulic modeling techniques and precise data entry. The aim is to contribute knowledge to assess flash flood risk and reduce impacts on communities and infrastructure. The selection of study areas with a history of severe flooding, such as the Lam Saphung Basin, Phrom River Basin, and Lam Chern River Basin Part 1 in Thailand, highlights the importance of thorough flash flood risk assessment. By leveraging the HEC-RAS model, the results of this research inform proactive risk management strategies, improve emergency preparedness and help develop sustainable mitigation measures. The results are important in developing emergency response strategies and overall recovery ability in areas at risk of flash floods. The research combines advanced hydrologic modeling and real-world flash flood data. In addition to the flood condition assessment, the extent of the flood area and associated hazards were assessed using a two-case simulation strategy. The study covers future scenarios related to land use changes and retrospective analysis of past flood events. The results have practical implications for improving emergency response strategies, land use planning, and overall resilience in flash flood-prone areas. The integrated approach emphasizes the research output to providing insights and actionable solutions for communities facing ongoing challenges posed by flash floods.

The quest for youthful, healthy skin and full, vibrant hair has long been a driving force in the dermocosmetics field. However, traditional approaches often struggle to address the underlying causes of aging, damage, and hair loss. Regenerative cosmetics, powered by skin tissue engineering, offer a transformative alternative. This review explores the emerging field of using engineered skin tissues for cosmetic purposes, focusing specifically on their potential for anti-aging, repair, and hair restoration applications. We discuss how these technologies aim to rejuvenate aging skin by promoting collagen production, reducing wrinkles, and improving overall skin function. Additionally, the use of engineered skin for wound healing and scar reduction is examined, highlighting their potential to improve the appearance and functionality of damaged skin. Finally, we advance the exciting prospects of utilizing skin tissue engineering techniques to regenerate hair follicles, potentially offering solutions for hair loss and promoting denser hair growth.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

Flash flooding is one of the most devastating natural events that leads to enormous and recurring loss of life. Kuwait was subjected to severe rainstorms in the winter of 2018 and 2020 followed by an extreme violent flood that had not been known in Kuwait since 1976. It resulted in several geomorphological and environmental impacts in urban and desert areas. This produced some positive results, such as geomorphological activity in landforms, the flow of some valleys and the prosperity of wildlife in the Kuwaiti desert. Negative results included some problems in the metropolitan area and destruction of some road networks that intersect the main valleys, and which were not equipped with crossings for avoiding floods. There was also the emergence of some problems in the infrastructure. Study of flash floods requires the involvement of all scientific and executive bodies to avoid environmental risk. The study aims to: 1- Monitor geomorphological and environmental changes. 2- Assess the impact of floods in the urban areas and on infrastructure. 3- Modeling the impact. 4- Creating solutions and adaptions to the flash flood. The study uses several methods such as remote sensing (RS), geographic information systems (GIS), hydrologic modeling and fieldwork to evaluate the impact of flash flood hazards on the sustainable urban development of Kuwait state. This approach is rarely used in Kuwait. We propose a novel method that could help decision-makers and planners in determining inundated flood zones before planning future urban developments in Kuwait, and help them to manage flood water, by identifying the most appropriate places for storage to exploit water in agriculture and drinking.

In this paper, a new type of self-excited thermomechanical oscillator containing an oscillating shape memory alloy (SMA) filament with two symmetrically arranged spheres is investigated. The self-excitation of the oscillations is due to a heater of constant temperature, which causes periodic contractions of the filament when it approaches it. The contracted filament moves away from the heater a distance sufficient to cool it. Under the action of the weight of the spheres, the cooled filament re-approaches the heater, causing the above processes to repeat periodically. On the basis of experimental studies, approximating functions of the heater's heat field distribution are derived. A dynamic model of the oscillator has been created, in which the minor and major hysteresis in the SMA alloy and the distribution of the heat field around the heater have been taken into account. By numerical solutions of the differential equations, the laws of motion of the spheres are obtained. The displacements of the spheres in two perpendicular directions were measured using an experimental system. The obtained experimental results validate the proposed dynamic model and its assumptions with a high degree of confidence. Conclusions are drawn about the stochastic nature of the oscillations due to the hysteresis properties of the SMA and the temperature variation of the natural frequency of the oscillating system.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

A novel means of applying radiotherapy in cancer treatment is the application of the radiation dose at a very high intensity for a very short time, FLASH radiotherapy (FLASH-RT). This technique involves exposure of tumors to >40 Gy/s, usually for less than one second. Studies conducted in cell and preclinical models suggest that FLASH-RT seems less damaging to normal tissues from adverse effects, relative to the same overall dose of radiation administered in conventional therapy (CONV-RT) which involves administration of lower levels of radiation repeated intermittently over a protracted period. In contrast, the susceptibility of tumor tissues to FLASH-RT is not diminished relative to CONV-RT. Within solid tumors both modes of dispensation of radiation produce an equivalent degree of cell damage. This differential between normal and malignant material has been found in isolated tissues, animal studies, and more recently in clinical trials. However, the classical radiation concept is that high energy linear transfer radiation (LET) is more damaging than the equivalent total dose of low LET. Thus, the susceptibility of cells should be greater to short-term exposure to high LET. This article discusses the potential reasons that may account for this discrepancy. While the relative protection given to untransformed tissues by FLASH-RT relative to tumor tissue is a major step forward in radiation therapy of cancer, the processes that lie behind this phenomenon are incompletely understood and are considered here.

Reconstructing 3D indoor scenes from 2D images has always been an important task in computer vision and graphics applications. For indoor scenes, traditional 3D reconstruction methods suffer from the lack of surface details, poor reconstruction of large flat surface textures and areas with uneven lighting, and many falsely reconstructed floating debris noises in the reconstructed models. We add adaptive normal priors to the neural implicit reconstruction process to optimize the network, and improve the accuracy of volume density prediction by adding regularization terms to the neural radiation field to constrain the volume density obtained by weight distribution, and learn a smooth SDF surface from the network to obtain an explicit mesh model. Experiments show that the method proposed in this paper outperforms the state-of-the-art methods on ScanNet, Hypersim, and Replica datasets.

The learning equations of an ANN are presented, giving an extremely concise derivation based on the principle of backpropagation through the descendent gradient. Then, a reflection is developed on the dual attention network that applies the learning equations and coordinates subnetworks toward purposeful behaviors. Speculation is made on possible developments of functionalities that could provide additional skills and at the same time shed light on competencies typical of ``natural intelligence".

Introduction: Obstructive sleep apnea syndrome (OSAS) is characterized by recurrent episodes of upper airway obstruction and involves intermittent hypoxia and sleep fragmentation, with potentially serious consequences for affected patients. (1–3). Although nocturnal polysomnography is the gold standard, it is an exam that is not readily available and is very expensive. (4). Hence, the need to find new diagnostic methods. Considering that the causes of OSAS can be divided into anatomical-structural ones, related to craniofacial anomalies, it has been hypothesized that anthropometric measurements taken by new 3D stereophotogrammetric systems could be useful as a diagnostic tool in pediatric patients with OSAS (5) (6). The primary objective of the study is, therefore, to evaluate the correlation between mandibular length measured between menton and gonion, obtained through 3D stereophotogrammetry using the "Face Scanner maxi 6", and the severity of OSAS (AHI classification), defined by the score of the Sleep Clinical Record (SCR) questionnaire in a group of pediatric patients with suspected obstructive sleep disorders. The secondary objective concerns the identification of possible correlations between other mandibular parameters estimated by 3D stereophotogrammetry and the severity of OSAS, defined by the McGill Oximetry Score (MOS), and the association between MOS and SCR to determine the AHI level. Materials and methods: The study considered patients who were prescribed a pulseoximetry exam due to suspected obstructive sleep disorders. All participating patients underwent a specialized orthodontic examination, which included completing the SCR questionnaire and taking facial photographs using a 3D stereophotogrammetric system. The SCR questionnaire considers 11 dental, nasal, oropharyngeal, and facial phenotype parameters to determine a final score from 0 to 18, indicating the risk of obstructive sleep apnea syndrome. The acquired stereophotogrammetric images were processed using dedicated software to obtain a three-dimensional model representing the patient's facial phenotype. Subsequently, anatomical landmarks and relevant anthropometric measurements were identified on the model, and it was assessed whether one or more of these showed concordance criteria with the parameters derived from SCR and MOS. The anthropometric evaluation was performed by expert operators, taking into account mandibular variables. Results: Fifteen patients were analyzed, with 2 excluded due to alterations in the stereophotogrammetric images caused by poor patient cooperation during the acquisition of the photographs. Spearman's correlation analysis was performed to investigate the relationship between anthropometric measurements, obtained by 3D stereophotogrammetry, and OSAS severity, by means of SCR, MOS, and SCR+MOS. A significant and negative correlation was observed between right mandibular length (gonion-menton) and MOS (ρ=−0.586, p=0.036). Conclusions: The result obtained has important implications for the field of study and suggests that future attention should focus more on the mandibular length variable as a determining factor for OSAS. However, the sample examined was relatively small, which might obscure the correlation with contralateral mandibular length and potential correlations with other mandibular/facial parameters. Additionally, the small sample size prevented stratification by sex and age. The study thus provides an important contribution to understanding the relationships between 3D stereophotogrammetry and pediatric OSAS but also highlights the need for further research that could potentially influence future developments in diagnosing OSAS in children.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Over 2.2 billion people across the globe face significant barriers to accessing essential ophthalmic care, with elderly, rural, and refugee populations being disproportionately affected. These obsta-cles deepen existing disparities in eye care. 3D printing is a novel technology that has the potential to transform the field and improve access through alleviating many patient-specific barriers. This article delves into the evolution of 3D printing within ophthalmology, highlighting its current ap-plications and future potential. It explores various 3D printing techniques and biomaterials, dis-cussing their effectiveness in creating advanced solutions such as bioengineered corneas, ocular prosthetics, and innovative treatments for dry eye syndrome. Additionally, 3D printing has rev-olutionized drug delivery systems for conditions like glaucoma, retinal diseases, and for ocular brachytherapy. Despite its promise, the integration of 3D printing into clinical practice presents challenges, which the article addresses alongside strategies for overcoming them. By mapping out the technological advancements and challenges, this review offers a roadmap for enhancing global eye care accessibility and improving patient outcomes on a global scale.

Traditional 3D reconstruction models have consistently encountered a challenge: attaining high recall of object edges while preserving precision. In this paper, we introduce a post-processing method Multi-Head Attention Refiner (MA-R) aimed at tackling this challenge by integrating a multi-head attention mechanism within the U-Net style refiner module. The 3D reconstruction model applying this method demonstrates excellence in parsing intricate image details, resulting in significant enhancement of boundary predictions and increased recall rates. In our experiments, our method significantly enhances the reconstruction performance of Pix2Vox++ when multiple images are utilized as input. Specifically, it achieves an enhanced Intersection Over Union score of approximately 1.1% compared to the original Pix2Vox++ model when 16-view images are employed.

With the current increase in the demand from animal and agricultural products, management of agrowaste has become critical to avoid greenhouse gas emissions. The present article investigates the applicability of ammonium bicarbonate synthesis via flash distillation to valorize and stabilize several types of anaerobic digestate produced from individual fermentations of amino acids. Prior to the development of the model in Aspen Plus v12, the description of the system aqua-ammonia-carbon dioxide provided by the electrolyte non-random two-liquid property method was validated with empirical data available in the literature. The content of CO₂ in the digestate was found to be responsible of the OH alkalinity (0.4 equivalents of acid/kg digestate), while the partial and total alkalinities (0.8 eq/kg digestate) were essentially derived from the content of NH₃. The most suitable conditions for the flash distillation were 95 ⁰C and 1 bar with the condensation occurring at 25 ⁰C. However, in order to attain the precipitation of NH₄HCO₃ in the distillate, it was necessary to consider digestates with a moisture content of 50 wt.%, since the minimum levels of inorganic nitrogen and inorganic carbon were not attained otherwise. Even under these conditions, few amino acids (i.e. arginine, glycine, and histidine) were able to provide an anaerobic digestate, upon fermentation, that would be suitable for NH₄HCO₃ stabilization. Despite alanine digestate and glutamine digestate presented sufficient concentrations of inorganic nitrogen and inorganic carbon, the NH₄HCO₃-stabilization was not feasible due to the limited volatilization of NH₃. The process of stabilization with a capacity of a tonne of digestate per hour was improved by adding hydrochloric acid or sodium hydroxide at rates 44 kg/h, leading to production of 34 kg NH₄HCO₃/h. The economic viability of this process needs to be investigated considering not only the market value of the isolated inorganic fertilizer but the carbon credits saved, resulting from handling a more stabilized organic manure. Furthermore, given the role of the volatile elements of the biogas as endogenous stripping agents, it is recommended to use a fresh and saturated digestate as feed for the flash distillation.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

Benveniste’s experiments – known in the lay press as the “water memory” phenomenon – are generally considered to be a closed case. However, the amount of data generated by twenty years of well-conducted experiments prevents closing the file so simply. An issue, which has been little highlighted so far, merits to be emphasized. Indeed, if Benveniste failed to persuade his peers of the value of his experiments, it was mainly because of a stumbling block, namely the difficulty of convincingly proving the causal relationship between the supposed cause (“informed water”) and the experimental outcomes in different biological models. To progress in the understanding of this phenomenon, we abandon the idea of any role of water in these experiments (“water memory” and its avatars). In other words, we assume that “control” and “test” conditions to be evaluated were physically identical and differed only by their respective designations. We show in this article how simple probabilistic considerations allow to build a model that accounts for all aspects of Benveniste’s experiments. In this model based on probability amplitudes, constructive and destructive interferences emerge – or not – according to the experimental context. The recording of a statistical regularity shapes the intertwined whole constituted by the probability amplitudes of the states of the experimenter’s cognitive structures and of the experimental system. This model provides an alternative explanation to Benveniste’s experiments where water plays no role and where the place of the experimenter is central.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

Deep underground laboratories offer advantages for conducting high-precision observations of weak geophysical signals, benefitting from a low background noise level. It is both valuable and feasible to enhance strong, noisy ground electromagnetic (EM) field data using synchronously recorded underground EM signals, which typically exhibit a high signal-to-noise ratio. In this study, we propose an EM field reconstruction method employing a Long Short-Term Memory (LSTM) recurrent neural network with referenced deep underground EM observations. Initially, a deep learning model was developed to capture the time-varying features of underground multi-component EM fields using the LSTM recurrent neural network. Subsequently, this model was applied to process synchronously observed strong, noisy data from other conventional observation systems, such as those at surface, to achieve noise suppression through signal reconstructions. Both theoretical analysis and practical observational data suggest that the proposed method effectively suppresses noise and reconstructs clean EM signals. This method is efficient and time-saving, representing an effective approach to fully utilizing the advantages of deep underground observation data. Furthermore, this method could be extended to the processing and analysis of other geophysical data.

The monocular structured light measurement system has low cost, simple algorithms, and a wide measurement range, making it widely applicable in multiple fields. However, in practical applications, the system may be affected by various factors including noise, non-linear intensity, changes in the reflectivity of the object being measured, and the calibration method and accuracy of the system, thereby reducing the measurement accuracy. In order to solve these issues, this paper proposes a new monocular structured light measurement method, mainly comprises the following two points: (a) A denoising algorithm for phase images based on DAE is proposed, which calculates the wrapped phase of the phase-shifted fringes after initial denoising by DAE. Then, a new phase-shifted fringe pattern is generated and input into DAE for iterative denoising, achieving high-performance image denoising and high-precision wrapped phase solution. (b) A new absolute phase height calibration algorithm is proposed, which introduces camera internal and external parameters and uses a two-layer feedforward network to directly establish the relationship between phase and the 3D coordinate system. Without the need for high-precision motion platforms, high-precision phase height calibration is attainable. In general, compared to conventional methods, the experimental results indicate the effectiveness of the proposed method for low-quality phase-shifted fringe 3D reconstruction. In addition, the measurement method described in this article also demonstrates effectiveness in high-dynamic scenes.

This paper will argue that memory from early childhood underlies many practices and beliefs that we commonly refer to as “religious”. The consciousness of young children does not yet have certain features that characterizes adult consciousness. This paper will concentrate on four of these: (I) a reality that is recognizable; (II) a sense of temporal duration; (III) a sense of self; (IV) an experience of the world that is deeply affected by our acquaintance with (a) language. Absence of these features presumably characterizes the consciousness of infants. It also often characterizes mystical experiences. The paper will argue that the human tendency to engage in so-called religious practices and beliefs makes most sense on the assumption that adults somehow preserve the memory of their state of being in childhood.

Due to the inherent limitations of a single viewpoint, reconstructing 3D human meshes 1 from a single image has long been a challenging task. While deep learning networks enable us to 2 approximate the shape of unseen sides, capturing the texture details of the non-visible side remains 3 difficult with just one image. Traditional methods utilize Generative Adversarial Networks (GANs) 4 to predict the normal maps of the non-visible side, thereby inferring detailed textures and wrinkles 5 on the model’s surface. However, we have identified challenges with existing normal prediction 6 networks when dealing with complex scenes, such as a lack of focus on local features and insufficient 7 modeling of spatial relationships.To address these challenges, we introduce EMAR—Enhanced 8 Multi-scale Attention-driven Single Image 3D Human Reconstruction. This approach incorporates 9 a novel Enhanced Multi-Scale Attention (EMSA) mechanism, which excels at capturing intricate 10 features and global relationships in complex scenes. EMSA surpasses traditional single-scale attention 11 mechanisms by adaptively adjusting the weights between features, enabling the network to more 12 effectively leverage information across various scales.Furthermore, we have improved the feature 13 fusion method to better integrate representations from different scales. This enhanced feature fusion 14 allows the network to more comprehensively understand both fine details and global structures 15 within the image. Finally, we have designed a hybrid loss function tailored to the introduced attention 16 mechanism and feature fusion method, optimizing the network’s training process and enhancing the 17 quality of reconstruction results.Our network demonstrates significant improvements in performance 18 for 3D human model reconstruction. Experimental results show that our method exhibits greater 19 robustness to challenging poses compared to traditional single-scale approaches.

Elbow dislocation and instability present significant clinical challenges, necessitating a thorough understanding of the underlying bio-mechanical mechanisms. In this study, a quasi-static three-dimensional finite element model of the human elbow joint is developed to investigate stress distribution and stages of dislocation in the human elbow under various loading conditions. The model simulates the elbow joint in different degrees of flexion (30°, 45°, 60°, and 90°) and forearm positions (pronation and supination), providing detailed insights into the progression of dislocation. Significant findings include the identification of high stress concentrations on the humerus at 90° flexion and on the radial and coronoid processes at 30°, 45°, and 60° flexion. Three reproducible stages of dislocation were observed, particularly in flexed positions with forearm pronation or supination. These stages align with experimental observations and highlight the initial occurrence of bony failures, such as radial head and ulnar coronoid fractures, preceding soft tissue tears. Clinically, the study underscores that early-stage low-impact posterior elbow dislocations retain enough stability to be managed with closed reduction and early mobilization. However, as dislocations progress, significant damage to the medial and lateral collateral ligaments is expected, necessitating more invasive treatments. This research provides valuable bio-mechanical insights into elbow dislocation, aiding in the development of improved treatment strategies and enhancing patient outcomes through precise and timely clinical interventions. The validated FEM serves as a powerful tool for pre-surgical planning offering a comprehensive understanding of elbow joint mechanics.

This study introduces a novel method for early prediction of Kimchi cabbage (Brassica rapa subsp. pekinensis (Lour.) Hanelt) height, utilizing drone imagery and a long short-term memory (LSTM) model. The research was conducted on a testbed at the National Institute of Agricultural Sciences (NAS) in South Korea, encompassing two distinct soil types (loam and sandy loam) to investigate their impact on growth. High-resolution drone images were captured throughout the growing season to generate a canopy height model (CHM) for estimating plant height at various stages. Missing height data were interpolated using a logistic growth curve, and an LSTM model was trained on this data to predict the final height of Kimchi cabbage at harvest. Three LSTM models were developed using time-series data collected at 29, 36, and 44 days after planting (DAP). The model trained on data from DAP 44 demonstrated the highest accuracy with a coefficient of determination (R²) of 0.83, a mean absolute error (MAE) of 2.48 cm, and a root mean square error (RMSE) of 3.26 cm, outperforming models trained on earlier data. Color-coded maps were generated to visualize the spatial distribution of predicted Kimchi cabbage heights, revealing variations in growth patterns across the testbed and confirming the model's potential for site-specific management. Considering the trade-off between accuracy and prediction timing, the model trained on DAP 36 data (MAE = 2.77 cm) was deemed optimal for informing cultivation management decisions. This research demonstrates the feasibility and effectiveness of integrating drone imagery, logistic growth curves, and LSTM models for early and accurate prediction of Kimchi cabbage height. The proposed technology enables data-driven decision-making for farmers, facilitating timely interventions based on predicted growth patterns. This could lead to improved crop yields, resource optimization, and a more sustainable agricultural future. Future research will focus on refining the model's accuracy and exploring its applicability to other crops, further expanding the potential of precision agriculture technologies.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

This paper examines the use of multisensory virtual reality (VR) as a novel approach in psychological therapy for autobiographical memory retrieval with benefits for cognitive enhancement, stress reduction etc. The research in this paper was done under Romanian Arut Research Grant no. 27/09/10/2023 ”Intelligent VR system for treating autobiographical/episodic memory deficits".  By simulating realistic multisensory experiences, VR technology offers an immersive environment that surpasses traditional therapeutic methods in effectiveness. Previous studies demonstrate improved outcomes in treating various psychological conditions (affective disorders and PTSD, specific phobias and age-related cognitive decline). Technological advancements in VR, such as olfactory integration cand contribute to the realism and therapeutic potential of these environments, the integration of various physical stimuli with VR holds promising potential psychological therapies and highlighting the need for further interdisciplinary research. In this pilot study we tested the efficacy of a new system for triggering autobiographical memory retrieval. For this we used images combined with odors in a congruent manner and offering participants the chance to interact with the VR environment by using 2 virtual hands. We evaluated the efficacy of this system using qualitative methods with emphasis on the evaluation of the emotions associated with memory recollection and the ease of triggering memories. All participants in our pilot study experienced intense emotions related to childhood or adolescence and the pleasant feelings they had during the experiment persisted even after it ended. This is an advancement to what exists currently and original research elements for our paper.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

Recent advances in organoid technology have revolutionized cancer biology and thera-peutic interventions, offering personalized immunotherapy treatment. Organoids, three-dimensional cell cultures derived from patient tumors, accurately replicate the tumor microenvi-ronment, providing unprecedented insights into tumor-immune interactions and therapeutic re-sponses. In this literature-based study, we discuss various culture methods for the diverse appli-cations of organoids in cancer immunotherapy, including drug screening, personalized treatment strategies, and mechanistic studies. Additionally, we address the technological challenges asso-ciated with these methods and propose potential future solutions to accelerate the development of novel immunotherapeutic approaches. This review highlights the transformative potential of or-ganoid models in advancing preclinical cancer immunotherapy modeling, screening, and evalua-tion, paving the way for more effective and personalized cancer treatments.

Responsible, efficient, and environmentally conscious energy consumption practices are increasingly essential for ensuring the reliability of the modern electricity grid. This study focuses on leveraging time series analysis to improve forecasting accuracy, crucial for various application domains where real-world time series data often exhibit complex, non-linear patterns. Our approach advocates for utilizing Long Short Term Memory (LSTM) and Bidirectional LSTM (BiLSTM) models for precise time series forecasting. To ensure a fair evaluation, we compare the performance of our proposed approach with traditional neural networks, time-series forecasting methods, and conventional decline curves. Additionally, individual models based on LSTM, Bi-LSTM, and other machine learning methods are implemented for a comprehensive assessment. Experimental results consistently demonstrate that our proposed model outperforms all benchmarking methods in terms of mean absolute error (MAE) across most datasets. Addressing the imbalance between activations by consumer and prosumer groups, our predictions show superior performance compared to several traditional forecasting methods, such as the Autoregressive Integrated Moving Average model (ARIMA) and Seasonal Autoregressive Integrated Moving Average model (SARIMA). Specifically, the root mean square error (RMSE) of Bi-LSTM is 5.35%, 46.08%, and 50.6% lower than LSTM, ARIMA, and SARIMA, respectively, on the May test data.

This study examines the feasibility of using event-related potentials (ERPs) obtained from electroencephalographic (EEG) recordings as biomarkers for long-term memory item classification. Previous studies have identified old/new effects in memory paradigms associated with explicit long-term memory and familiarity. Recent advancements in convolutional neural networks (CNNs) have enabled the classification of ERP trials under different conditions and identification of features related to neural processes at the single-trial level. We employed this approach to compare three CNN models with distinct architectures using experimental data. Participants (N = 25) performed an association memory task while recording ERPs that were used for training and validation of the CNN models. The EEGNET-based model achieved the most reliable performance in terms of precision, recall, and specificity compared with the shallow and deep convolutional approaches. The classification accuracy of this model reached 70% for known items and 62% for unknown items. Good overall accuracy requires a trade-off between recall and specificity and depends on the architecture of the model and the dataset size. These results suggest the possibility of integrating ERP and CNN into online learning tools and identifying the underlying processes related to long-term memorization.

Objective: The aim of this in vitro study was to evaluate the accuracy of resin-based fixed dental restorations, namely veneers, single crowns, and four-unit fixed partial dental prosthesis (FPDs) using two different 3D printers and polymer-based materials. Materials and Methods: A standard maxillary polyurethane jaw model containing prepared teeth was scanned using an intraoral scanner. The generated STL data were used to design the restorations virtually using CAD software. Two 3D printers were utilized for the provisional digital light processing and stereolithography for the castable resin patterns. Each printer produced 10 specimens of each type of restoration, for a total of 80 restorations. The 3d-printed restorations were then 3D scanned using the same intraoral scanner and evaluated for external and internal dimensional accuracy in terms of trueness and precision. A one-way ANOVA and Two-sample T-Test were implemented to compute the precision (variability between groups) and trueness (with the designed CAD model). A level of statistical significance of p-Value

Neuron degeneration is the most common old age complications worldwide. Alzheimer's disease (AD) is one of the most common neurodegenerative condition with limited drug options and significant adverse effects. Hence, there is a growing interest in exploring natural products for their potential pharmacological activities against AD. This study investigates the efficacy of Verbesina encelioides flower extract (VFE) in alleviating neurobehavioral damage induced by Scopolamine in rat mimicking AD model. GC-MS analysis showed that V. encelioides flower extract is rich in carotenoids like spirilloxanthin. Various behavioural models were used to assess the rats' learning and memory capabilities. Additionally, biochemical tests were conducted on the AD rat models to evaluate oxidative stress in the brain, including superoxide dismutase (SOD), nitric oxide (NO), reduced glutathione (GSH), and anti-acetylcholinesterase (AChE) enzyme assays. Findings from this study suggest that the VFE significantly improved the rats' cognitive aptitude and alleviated them from oxidative stress by reducing free radical generation. Based on the results obtained from GC-MS analysis, in silico interaction analysis of gingkolide A and spirilloxanthin with acetylcholinesterase was carried out. In summary, this study suggests that V. enceloides flower extract improves learning abilities and mitigates cognitive deficits caused by scopolamine. Thus V. enceloides could be potentially seen as natural therapeutic intervention against neurodegenerative disorders likes Alzheimer’s disease and dementia.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

This study presents the design and comprehensive 3D multiphysics simulation of a novel microfluidic immunosensor for real-time, non-invasive monitoring of pro-inflammatory biomarkers in human sweat. The patch-like device, designed using COMSOL Multiphysics, integrates magnetofluidic manipulation with direct-field capacitive sensing. The sensor comprises two distinct units: an immunocomplex enhancement unit, employing a series of microcoils to optimize the binding efficiency, reaction kinetics, and homogeneity of biomarker-magnetic nanoparticle (MNP) interactions, thereby enhancing the sensor's specificity; and a layered capacitive sensing unit, designed to concentrate and detect biomarker-tagged MNPs, thus amplifying sensitivity. Simulations of the capacitive sensing unit revealed a substantial sensitivity increase of up to 42.48\% at an 85\% MNP concentration within the detection zone. These findings highlight the potential of the proposed immunosensor for efficient and precise real-time biomarker monitoring, which may facilitate early disease diagnosis and enable personalized healthcare interventions.

K-band radar waves have high penetration and low attenuation coefficients. However, the wavelength of this radar wave is relatively short; thus, designing and preparing both broadband and wide-angle radar wave absorbers in this band presents considerable challenges. In this study, a resin-based K-band radar wave absorber with a biomimetic lotus leaf structure was designed and formed by UV curing. Here, microscale lotus leaf papillae and antireflection structures were prepared using a DLP 3D printer, and the contact angle between the material and water droplets was increased from 56° to 130°. In addition, the influence of the geometric parameters of the lotus leaf antireflection structure on the electromagnetic absorption performance and mechanical strength was investigated. After simulation optimization, the maximum electromagnetic loss of the lotus leaf structure 3D printed sample was −32.3 dB, and the electromagnetic loss was below −10 dB in the 20.8–26.5 GHz frequency range. When the radar incidence angle was 60°, the maximum electromagnetic loss was still less than −10 dB. The designed lotus leaf structure has a higher mechanical energy absorption per unit volume (337.22 KJ/m3) and per unit mass (0.55 KJ/Kg) than commonly used honeycomb lightweight structures during the elastic deformation stage, and we expect that the designed structure can be used as an effective lightweight material for K-band radar stealth.

Recent research has suggested that working memory training interventions may benefit children with Developmental Language Disorder (DLD). The current study investigated a short and engaging adaptive working memory intervention that targeted executive skills and aimed to improve both language comprehension and working memory abilities in children with DLD. Forty-seven 6- to 10-year-old children with DLD were randomly allocated to an executive working memory training intervention (n=24) or an active control group (n=23). A pre-test/intervention/post-test/9-month-follow-up design was used. Outcome measures included assessments of language (to evaluate far transfer of the training) and working memory (to evaluate near transfer of the training). Hierarchical multiple regression analyses controlling for pre-intervention performance and age found group to be a significant predictor of sentence comprehension and of performance on six untrained working memory measures at post-intervention and 9-month follow-up. Children in the intervention group showed significantly higher language comprehension and working memory scores at both time points than children in the active control group. The intervention programme showed potential to improve working memory and language comprehension in children with DLD and demonstrated several advantages: it involved short sessions over a short period; caused little disruption in the school day; and was enjoyed by children.

Tailings generated by mining account for the largest proportion of global waste from industrial activities. Copper is relatively uncommon world-wide, with low concentrations in sediments and waters, yet is very elevated around mining sites. On the Keweenaw Peninsula of Michigan, USA, jutting out into Lake Superior, 140 mines extracted native copper from the Portage Lake Volcanic Series, part of an intercontinental rift system. Between 1901-1932, two mills at Gay (Mohawk, Wolverine) sluiced 22.7 million metric tonnes (MMT) of copper-rich tailings (stamp sands) into Grand (Big) Traverse Bay. Here we examine: 1) 3D coastal elevation and reef bathymetry, 2) particle dispersal, 3) copper concentrations and leaching, plus 4) shoreline toxicity. About 10 MMT of tailings created a migrating coastal beach that stretches 7 km from the Gay pile to the Traverse River Seawall. Another 10 MMT are moving underwater on the coastal shelf, threatening Buffalo Reef, an important lake trout and whitefish breeding ground. Aerial photos, ALS (plane) LiDAR, and relatively inexpensive UAS (drone) surveys characterize shoreline structure and aid initial remediation. Because sands (natural beach quartz, stamp sand basalt) are silicates of similar density, particle dispersal is similar and challenging. However, stamp sand beaches contrast greatly with natural sand beaches in both physical profile and chemistry. Dispersing particles retain copper, and release toxic concentrations. Leaching is elevated by exposure to high DOC and low pH waters. Field experiments, shoreline seining, and benthic sampling confirm serious impacts on aquatic biota, supporting tailings removal.

Direct-to-blister copper flash smelting slag contains up to 14% of copper and 2-4% of lead. Considering this fact, this material is subjected to the high-temperature reduction process. After this, converting process is performed on the Cu-Pb-Fe alloy being the product of decopperization process in electric furnace. An alternative to the presently used processing of flash smelting slag would be its hydrometallurgical treatment and selective recovery of Pb and Cu. This paper presents the results of laboratory tests on flash smelting slag leaching with citric acid solutions. The experiments performed allowed to determine the process parameters at which the Pb concentration in the post-leaching sediment reached the value of 0.41-0.6% while the Pb content in flash smelting slag was 3.05%. Analogous values for copper were 11.5-11.8% (after leaching) and 12.44% (before). Material after leaching in citric acid solutions can be processed, in the second step, using sulfuric acid solutions, and it could lead to the recovery of almost all copper contained in it.

The paper presents two procedures for creating 3D discrete models of apple using the finite element method (FEM). The study focused on a new Polish apple variety, Chopin at development, ripening, and senescence maturity stages. The analysis of the results allowed for the determination that, depending on the desired outcomes, the parenchymal tissue can be considered as a material with either elastic or elastoplastic properties. Model validation was performed using displacement-force relationships and changes in contact area as a function of loading force obtained from compression tests. Elastoplastic models reflect empirical studies much better. The fit of the elastic models, based on force vs. displacement curves, ranged from 79% to 83%, while the fit of the elastoplastic models to empirical data ranged from 91% to 96%. Elastic models, on the other hand, are well-suited to the modified force vs. displacement curves, which reflect the elastic behavior of apples under compression test. Contour plots of pressures for elastoplastic models align much better with the test results than those for elastic models. 4. Similarly, in the case of contact area values, the elastoplastic models outperformed the elastic models, achieving a fit between 92% and 96%, while the elastic models reached only 82% to 83% compliance.

In addition to changes in the amount of rain, changes in land use upstream are considered a factor that directly affects the maximum runoff flow in a basin, especially in areas that have experienced floods and flash floods. This research article presents the application of the SWAT model to assess runoff in areas that have experienced flash floods, in order to analyze the proportion of land use change to the maximum runoff. Study areas that had experienced flash floods were in 3 basins in Thailand (Lam Saphung Basin, Phrom River Basin, and Chern River Basin Part 1 which is a subbasin of the Nam Chi River Basin). This study analyzed two main factors that influence runoff in the river basin: Changes in rainfall and changes in land use by considering 2 simulation situations.: (1) Changes in land use affecting runoff assessed by considering land use maps in 2006, 2008, 2010, 2015, 2017, 2019, and 2021 when using rainfall data only in the year 2021 for all cases, and (2) Changes in the amount of rainfall influencing runoff by considering the rainfall record in 2006, 2008, 2010, 2015, 2017, 2019, and 2021 when using the land use data only in the year 2021 for all cases. The results of the study found that the SWAT model can be effectively applied to estimate annual runoff in areas that have experienced flash floods under 8 parameters with R2 values of 0.74, 0.82 and 0.74 for the Lam Saphung River Basin and the Phrom River Basin and the Chern River Basin Part 1 respectively. In addition, it was found that the proportion of land use changes that involved changes from forest areas to residential areas was the greatest from 2008 to 2010 in the Phrom River Basin and Chern River Basin Part 1. This resulted in an increase in the maximum runoff amount of 77.78% and 46.87%, respectively. When land use was constant, it was found that the rainfall in 2010, which was the highest, also had the greatest impact on the runoff in all 3 areas.

Flash flood is one of the most significant natural disasters in China, particularly in mountainous area, causing heavy economic damage and casualties of life. Accurate risk assessment is critical to an efficient flash flood management. There are more than 530,000 small watersheds in 2058 counties in China where flash flood should be prevented. In practice, with limited fund and different risk levels, the priorities of each small watershed for flash flood prevention and control are also needed for an efficient flash flood management. This paper, take Licheng county in China as an example, aims to give out these priorities for management. First, sensitive indexes are identified among index system, which includes 9 indexes based on underlying surface characteristics of small watershed in hilly region. Second, the range of each index and the rank division of each index for evaluation are determined. Based on the rank divisions for evaluation, the flash flood risk grade eigenvalue (H) is calculated by Variable Fuzzy Method (VFM ) using 1000 samplings generated by Latin hypercube sampling method. Third, the key sensitivity factors that affect flash flood risk grade eigenvalue (H) are assessed by two different global sensitivity analysis methods -- stepwise regression analysis and mutual entropy. Both results indicate that watershed slope (S) is the most sensitive factor; the second is antecedent precipitation index (CN); while other factors are slightly different sensitive in sequence. This study shows that stepwise regression analysis and mutual information analysis are appropriate for the sensitivity analysis of mountain flash flood risk. Finally, based on watershed slope (S), the priorities of flash flood prevention and control of 119 small watersheds in Licheng county are given out.

Recent evidence has highlighted the critical role of memory cells in maintaining lifelong food allergies, thereby identifying these cells as therapeutic targets. IgG⁺ memory B cells replenish pools of IgE-secreting cells upon allergen exposure, which contract thereafter due to the short lifespan of tightly regulated IgE-expressing cells. Advances in the detection and highly dimensional analysis of allergen-specific B and T cells from allergic patients have provided insight on their phenotype and function. The newly identified Th2A and Tfh13 populations represent a leap in our understanding of allergen-specific T cell phenotypes, though how these populations contribute to IgE memory responses remains poorly understood. Within, we discuss the mechanisms by which memory B and T cells are activated, integrating knowledge from human systems and fundamental research. We then focus on memory reactivation; specifically, on the pathways of secondary IgE responses. Throughout, we identify areas of future research which will help identify immunotargets for a transformative therapy for food allergy.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

Atopic dermatitis (AD) is a chronic inflammatory disorder presenting a dysregulated immune response and derangement of the epidermal barrier lipids. The Th2-type cytokines interleukin IL-4 and IL-13 play a prominent role in AD by activating the Janus Kinase/Signal Transduction and Activator of Transcription (JAK/STAT) intracellular signal axis. This study aimed to investigate the role of JAK/STAT in the lipid perturbations induced by Th2 signaling in 3D-epidermal equivalents. We used tofacitinib, a low-molecular-mass JAK inhibitor, to screen for the JAK/STAT-mediated deregulation of lipid metabolism. Th2 cytokines decreased the expression of elongases 1, 3, and 4, and serine-palmitoyl-transferase and increased that of sphingolipid delta(4)-desaturase, and carbonic anhydrase 2. Th2 cytokines inhibited the synthesis of palmitate and caused a depletion of triglycerides. This depletion was associated with altered PC profiles and fatty acid (FA) metabolism. Overall, the ceramide profiles were minimally affected. Except for most sphingolipids and very long chain FAs, the effects of Th2 on lipid pathways were reversed by co-treatment with tofacitinib. An increase in the mRNA levels of CPT1A and ACAT1, reduced by tofacitinib, suggests that Th2 cytokines promote FA beta-oxidation. In conclusion, pharmacological inhibition of JAK/STAT activation prevents the lipid disruption caused by halted homeostasis of FA metabolism.

Background/Objectives: Conventional surgery gland using the naked eye remains the standard for submandibular gland resection. Owing to its excellent automatic focus and high magnification, the ORBEYE 3D system introduces precise submandibular resection with less stress. Therefore, we examined the usefulness of the exoscope in submandibular gland resection for the first time. Methods: This retrospective study enrolled 12 patients who underwent submandibular gland resection using an ORBEYE exoscope at the Department of Head and Neck Surgery and Otorhinolaryngology at Kansai Medical University from April 2021 to March 2024. Surgical outcomes were retrospectively reviewed. Results: The mean age of the 12 patients (six females and six males) was 58.5 years (23–83 years). The final histopathology showed pleomorphic adenoma in eight cases, non-sebaceous-type lymphadenoma and carcinoma ex pleomorphic adenoma in one case each, and sialolithiasis with chronic inflammation in two cases. We performed facial artery and vein sparing in all cases except one in which level I neck dissection, including the submandibular gland, was performed. In all cases, we identified the marginal mandibular branches of the facial, hypoglossal, and lingual nerves, as well as the submandibular duct. No postoperative complications occurred in any patient. The mean operative time was 104 min (80–129 min). The mean blood volume lost was 20 mL (5–43 mL). Conclusions: Using ORBEYE in submandibular gland resection will contribute to preserving the mandibular marginal branch of the facial and lingual nerves and the facial artery and vein, and visualizing the submandibular duct, which are important structures surrounding the submandibular gland.

Previous studies reported a reduction of the perceived effort and an improvement of the perfor-mances of healthy subjects and patients when a motor task was combined with artistic images with respect to non-artistic images. This phenomenon, called Michelangelo effect, could contribute to the efficacy of art therapy in neurorehabilitation. In this study, the possible occurrence of this effect was tested in a cognitive task by asking to 15 healthy subjects and 17 patients with stroke to solve a digital version of the classical memory card game. Three different types of images were used in a randomized order: French cards, artistic portraits, and photos of famous people (to compensate the possible effects of face recognition). Healthy subjects were involved to test the usability and the load demanding of the developed system, reporting no statistically significant differences among the three sessions (p > 0.05). Conversely, patients had a better performance in terms of time (p = 0.014) and number of trials (p = 0.007) needed to complete the task in presence of artistic stimuli, accompanied by a reduction of the perceived effort (p = 0.033). Furthermore, artistic stimuli, with respect to the other two types of images, seemed more associated to visuo-spatial control than to linguistic functions.

Three-dimensional (3D) geological modeling technology offers intricate geological information services and technical support for the research of urban geological conditions and their evolutionary mechanisms. It further facilitates the analysis of environmental geological problems, encompassing their distinguishing features and genetic mechanisms. The precision of such three-dimensional models is predominantly influenced by the caliber of modeling data, the chosen modeling methodologies, and the intricacy of the modeled geological objects. This research, exemplified by the three-dimensional geological structure modeling of the Wuhan metropolitan development area, aims to explore a comprehensive three-dimensional modeling framework for urban geology, particularly in scenarios with large-scale and complex geological conditions. This study holds significant technical value in enhancing the application of 3D geological modeling, as well as practical importance for urban geological investigations and research.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

This paper explores indigenous perspectives on the understanding and management of cultural heritage within the Mapungubwe and Makgabeng Cultural landscapes in South Africa. State-based management system paid little attention to indigeneity resulting in contested interpretation of the archaeological past. This by-passing of indigenous input is a product of colonial and apartheid policies that glorified Western practices at the expense of black African heritage stakeholders. World heritage mechanisms are also skewed in favor of modern practice which is overly designed to be sensitive to tangible aspects of the past than the intangible elements that make up much of indigenous African heritage. We used the archaeology of Mapungubwe and Makgabeng Cultural landscapes as a test case for the impact of indigenous voices on heritage, but the results have wider applicability. We employed semi-structured interviews and focus group discussions to gather qualitative data that we calibrated with our lived experiences as products of Tsonga-speakers from this broader landscape. The results expose that indigenous people use physical manifestation of sites, ethnographic inquiry, names, oral history, spirit mediums, landscape memory, genealogy, and praise poetry to identify, interpret, evaluate, and manage their cultural heritage. Additionally, indigenous perspectives which rely on collective memory, ritual practices, and indigenous knowledge systems have huge potential for enriching our understanding of the archaeological heritage. We propose a more inclusive archaeology and heritage management practice that involve indigenous groups in the identification, interpretation, grading, and presentation of the African past.

This study examines the relationship between semantic memory and social cognition in schizophrenia, addressing how these cognitive domains intersect. Semantic memory, which includes general world knowledge and word meanings, was evaluated using verbal fluency tasks and the Camels and Cactus Test. Social cognition, essential for social interaction, was assessed through emotion recognition (Faces Test) and Theory of Mind (Hinting Task). Participants included 50 individuals with schizophrenia and 30 controls. The schizophrenia group showed significantly lower performance on both semantic memory and social cognition tasks. Notably, strong correlations were found between the Camels and Cactus Test and social cognition measures, suggesting that social cognition deficits in schizophrenia may be linked to semantic memory impairments. Regression analyses highlighted that the Camels and Cactus Test significantly predicted social cognition performance, independent of symptomatology. These findings underscore the interconnectedness of semantic memory and social cognition in schizophrenia, suggesting that semantic memory deficits, particularly in non-categorical associations, play a important role in social cognitive impairments. This study provides new insights into the cognitive underpinnings of schizophrenia, emphasizing the need for further research to explore these relationships and their implications for cognitive models and therapeutic interventions.

Understanding the complex relationship between sleep and memory is a major challenge in neuroscience. Many studies on memory consolidation in humans suggest that sleep triggers offline memory processes, resulting in less forgetting of declarative memory and performance stabilization in non-declarative memory. However, issues related to non-optimal experimental designs, task characteristics and measurements, and inappropriate data analysis practices can significantly affect the interpretation of the effect of sleep on memory. In this article, we discuss these issues and suggest constructive solutions to address them. We believe that implementing these solutions in future sleep and memory research will significantly advance this field by improving the understanding of the specific role of sleep in memory consolidation.

To live in the information society means to be surrounded by billions of electronic devices full of sensors that constantly acquire data. This enormous amount of data must be processed and classified. A solution commonly adopted is to send these data to server farms to be remotely elaborated. The drawback is a huge battery drain due to high amount of information that must be exchanged. To compensate this problem data must be processed locally, near the sensor itself. But this solution requires huge computational capabilities. While microprocessors, even mobile ones, nowadays have enough computational power, their performance are severely limited by the Memory Wall problem. Memories are too slow, so microprocessors cannot fetch enough data from them, greatly limiting their performance. A solution is the Processing-In-Memory (PIM) approach. New memories are designed that are able to elaborate data inside them eliminating the Memory Wall problem. In this work we present an example of such system, using as a case of study the Bitmap Indexing algorithm. Such algorithm is used to classify data coming from many sources in parallel. We propose an hardware accelerator designed around the Processing-In-Memory approach, that is capable of implementing this algorithm and that can also be reconfigured to do other tasks or to work as standard memory. The architecture has been synthesized using CMOS technology. The results that we have obtained highlights that, not only it is possible to process and classify huge amount of data locally, but also that it is possible to obtain this result with a very low power consumption.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

In recent years, many molecular and environmental factors have been studied to understand how synaptic plasticity is modulated. Sleep, as an evolutionary conserved biological function, has shown to be a critical player for the consolidation and filtering of synaptic circuitry underlying memory traces. Although sleep disturbances do not alter normal memory consolidation, they may reflect fundamental circuit malfunctions that can play a significant role in exacerbating diseases, such as autism and Alzheimer’s disease. Very recently, scientists sought to answer part of this enigma and they identified p75 neurotrophic receptor (p75NTR) as a critical player in mediating impairments in hippocampal-dependent associative plasticity upon sleep deprivation. This paper will review the role of the p75NTR, critically discuss the impact and implications of this research as the bridge for sleep research and neurological diseases.

The shape memory alloys belong to the smart materials thanks to their thermomechanical proprieties' reply to thermal or to mechanical loading. These materials can change shape, stiffness, displacement, natural frequency, and many mechanical characteristics in response to stress or to heat such as conduction, convection or radiation. However, heating by convection or conduction are the most useful and studied methods unlike radiation. Therefore, this paper aims to study the radiation effect on the shape memory alloy behavior

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

The movement of liquid droplets on the energy gradient surface has attracted extensive attention. Inspired by biological features in nature, such as the periodic spindle-shaped nodes in spider silks and conical-like barbs of cacti, the structure-property-function relationship of multifunctional gradient surfaces. In this study, a series of specific patterns are fabricated by 3D printing technology, followed by modification via the atmospheric pressure plasma treatment and liquid phase chemical deposition, resulting in enhancing the ability of water droplets of 5μL to travel 18.47mm on a horizontal plane and 22.75mm against gravity up to 20° tilting angle. Additionally, analysis techniques have been employed including contact angle analyzer, ESCA and laser confocal microscope to evaluate the sample performance. This work could further be applied to many applications related to microfluidic devices, drug delivery and water/fog collection.

In a 1.5°C warmer world, the Northeastern (NE) South America’s ecosystems will experience more severe droughts, associated with decreasing rainfall. The severity of flash drought events based on vegetation and surface soil moisture has not been identified over the Caatinga ecosys-tem. This study aimed to characterize the impact of flash drought events on vegetation response via soil moisture over NE South America during the first two decades of the 2000s. Three drought indices were used to characterize flash droughts: the Standardized Difference Vegetation Index (SDVI) derived from Meteosat Second Generation (MSG), the Standardized Precipitation Index (SPI) from ground-data, and the Surface Soil Moisture (SSM) product-based Soil Moisture and Ocean Salinity (SMOS). Results revealed dramatic impacts of flash drought events on vegetation dynamics that caused abrupt changes in the regional vegetation phenology. The regional patterns of flash drought events in 2012 over NE South America were identified and had a severe impact on its Caatinga-like vegetation-dependent moisture response. In 2012, anomalously long dry spells with negative rainfall anomalies in the non-rainy season and persistent on vege-tation greenness and rapidly decreased soil moisture were prominent, thus identifying NE South America to the impacts of flash drought events. Additionally, the results from the trends analysis of radiance fluxes estimated from the MSG satellites over 18 years revealed that an overall drying trend in the NE South America semiarid ecosystem during the last two decades. Here, flash drought events were identified as the conse-quent rainfall deficiency at SPI-3< −1 for a period of five consecutive weeks or more, which the soil moisture content dropping from the 40th percentile to below the 20th percentile, with the NDVI lower than 0.30 unit. These results could be useful to guide flash-droughts early warning systems in NE South America.

The sudden onset of natural hazards such as a flash flood events can be devastating to a country or region, often affecting numerous communities, and humanitarian supply chains play a major role in enabling the timely recovery of economic and social activities. However, the uncertainty and suddenness of natural disasters such as flash floods, as well as the potential for aftershocks, require humanitarian supply chains to be resilient during the relief process. This research first adopts the Delphi and literature review methods to identify the key indicators in the humanitarian supply chain to form an evaluation index system. Then, taking the 2021 mega-flash flood event which affected four cities in the mountainous region under the jurisdiction of the Zhengzhou municipal government, the ANP method is used to calculate the weights of each indicator and combines the weighted results with the Multi-styling and stereotyping method under Pythagorean fuzzy (PFs-VIKOR) to make an evaluation of the resilience of the humanitarian supply chain in the relief process. The findings suggest that policy makers and decision makers should pay close attention to the coordination of the parties involved in the humanitarian supply chain and improve the level of resilience of the entire supply chain by enhancing the resource scheduling capacity and responsiveness. At the same time, the VIKOR evaluation of the 4 cities highlighted the humanitarian supply chain in Dengfeng City to be most effective in this event due to the close cooperation and positive response of all parties involved in the humanitarian supply chain. The findings of this research provide some useful suggestions and guidance to the various practitioners involved in the humanitarian supply chain. Furthermore, the evaluation of the performance of the four cities in this mega-flash flood event provides some helpful indication of the importance of the various emergency measures which can help to inform policy recommendations for the Zhengzhou municipal government.

Brain pathological changes impair cognition early in disease etiology. There is an urgent need for understanding aging-linked mechanisms of early memory loss to develop therapeutic strategies and prevent the development of cognitive impairment. Tusc2, also named Fus1, is a mitochondrial-resident protein regulating Ca2+ fluxes to and from mitochondria impacting overall health. We reported that Tusc2-/- female mice develop chronic inflammation and age prematurely, causing age- and gender-dependent spatial memory deficits at 5 m.o. Therefore, we investigated Tusc2-dependent mechanisms of memory impairment in mice, comparing changes in resident and brain-infiltrating immune cells. Interestingly, Tusc2-/- female mice demonstrated proinflammatory increase in astrocytes, IFN-γ expression in CD4+T cells and Granzyme-B in CD8+T cells. We also found fewer FOXP3+ T-regulatory cells and Ly49G+ NK and Ly49G+ NKT cells in female Tusc2-/- brain, suggesting a weakened anti-inflammatory response. Moreover, Tusc2-/- hippocampi exhibited Tusc2- and sex-specific protein changes associated with brain plasticity, including mTOR activation, and Calbindin and CamKII dysregulation affecting intracellular Ca2+ dynamics. Overall, data suggest that dysregulation of Ca2+-dependent processes and proinflammatory brain microenvironment heighten in Tusc2-/- mice could underlie cognitive impairment. Thus, strategies to modulate the brain’s Tusc2-, Ca2+, and mitochondria-dependent pathways should be explored to improve cognitive health.

Digital machine intelligence has evolved from its inception in the form of computation of numbers to AI, which is centered around performing cognitive tasks that humans can perform, such as predictive reasoning or complex calculations. The state of the art includes tasks that are easily described by a list of formal, mathematical rules or a sequence of event-driven actions such as modeling, simulation, business workflows, interaction with devices, etc., and also tasks that are easy to do “intuitively”, but are hard to describe formally or as a sequence of event-driven actions such as recognizing spoken words or faces. While these tasks are impressive, they fall short in applying common sense reasoning to new situations, filling in information gaps, or understanding and applying unspoken rules or norms. Human intelligence uses both associative memory and event-driven transaction history to make sense of what they are observing fast enough to do something about it while they are still observing it. In addition to this cognitive ability, all bio-logical systems exhibit autopoiesis and self-regulation. In this paper, we demonstrate how machine intelligence can be enhanced to include both associative memory and event-driven transaction history to create a new class of knowledge-based assistants to augment human intelligence. The digital assistants use global knowledge derived from the Large Language Models to bridge the knowledge gap between various participants interacting with each other. We use the general theory of information and schema-based knowledge representation to create the memory and history of various transactions involved in the interactions.

Kynurenic acid (KYNA) is an endogenous tryptophan (Trp) metabolite known to possess neuroprotective property. KYNA plays critical roles in nociception, neurodegeneration, and neuroinflammation. A lower level of KYNA is observed in patients with neurodegenerative diseases such as Alzheimer’s and Parkinson’s diseases or psychiatric disorders such as depression and autism spectrum disorders, whereas a higher level of KYNA is associated with the pathogenesis of schizophrenia. Little is known about the optimal concentration for neuroprotection and the threshold for neurotoxicity. In this study the effects of KYNA on memory functions were investigated by passive avoidance test in mice. Six different doses of KYNA were administered intracerebroventricularly to previously trained CFLP mice and they were observed following 24 hours. High doses of KYNA (i.e., 20-40 μg/2 μl) significantly decreased the avoidance latency, whereas a low dose of KYNA (0.5 μg/2 μl) significantly elevated it compared with controls, suggesting that the low dose of KYNA enhanced memory function. Furthermore, six different receptor blockers were applied to reveal the mechanisms underlying the memory enhancement induced by KYNA. The series of tests revealed the possible involvement of the serotonergic, dopaminergic, α and β adrenergic, and opiate systems in the nootropic effect. The study confirmed that a low dose of KYNA improved a memory component of cognitive domain, which was mediated by, at least in part, four systems of neurotransmission in an animal model of learning and memory.

The role of innate immunity in neutralization of viral infections (including COVID-19) and forming long-lasting and specific immune memory is considered. It is assumed that antiviral protection is generated by the mechanism of RNA interference (RNAi) and is based on the presence of specific viral patterns in the DNA library of the host cells.

CO2 emissions resulting from the production of cement is a major issue, but can be limited by the partial substitution of cement by low-carbon-impact additions. The aim of this study was the formulation of a ternary binder based on ordinary Portland cement (OPC), ground granulated blast-furnace slag (GGBS) and flash-calcined sediment (FCS), a dredged waste which was valorized after applying a new heat treatment: flash calcination. The used materials were physically, chemically and mineralogically characterized. The composition of the formulations was optimized using mixture designs. Five formulations, one reference formulation RM (100% OPC), one binary formulation (50% OPC/50% GGBS), and three ternary formulations with a variable FCS rate (10%, 15%, 20%), were selected and characterized fresh and hardened. Results showed that the incorporation of FCS reduced the workability and increased the density. In addition, a decrease in the initial setting time and the heat of hydration peak were observed. In the hardened state, the formulation containing 10% FCS showed 90-day mechanical strengths superior to that of RM. The use of FCS in ternary binders could reduce the environmental impact by reducing greenhouse gas emissions.

Aquifer karstic structures, due to their complex nature, present significant challenges in accurately mapping their intricate features. Traditional methods often rely on invasive techniques or sophisticated equipment, limiting accessibility and feasibility. In this paper, we propose a new approach to non-invasive, low-cost 3D reconstruction using a camera that observes the light projection of a simple diving lamp. Our method capitalizes on the principles of structured light, leveraging the projection of light contours onto the karstic surfaces. By capturing the resultant light patterns with a camera, we reconstruct three-dimensional representations of the structures. The simplicity and portability of the equipment required make this method highly versatile, enabling deployment in diverse underwater environments. We validate our approach through extensive field experiments conducted in various aquifer karstic settings. The results demonstrate the efficacy of our method in accurately delineating intricate karstic features with remarkable detail and resolution. Furthermore, the non-destructive nature of this technique minimizes disturbance to delicate aquatic ecosystems while providing valuable insights into the subterranean landscape. This innovative methodology not only offers a cost-effective and non-invasive means of mapping aquifer karstic structures but also opens avenues for comprehensive environmental monitoring and resource management. Its potential applications span hydrogeological studies, environmental conservation efforts, and sustainable water resource management in karstic terrains worldwide.

Introduction: The term 3D printing is commonly used to depict an assembling method whereby the final form of an object is the result of the addition of different layers to build the frame of an object. This procedure is more accurately portrayed as additive manufacturing and is likewise alluded to as fast prototyping. The term 3D printing, in any case, is generally new and has been an active part of current developments in Dentistry. Much publicity encompasses the evolution of 3D printing, which is hailed as an innovation that will perpetually change CAM manufacturing, including in the dental sector. This review is the first part in a 3D Printing series that looks at the history of 3D Printing, the technologies available and reviews the literature relating to the accuracy of these technologies. Conclusions: The recent advancement in digital dentistry to incorporate these tools has modernised dental practices by paving the way for computer-aided design (CAD) technology and rapid prototyping. The use of 3D printing has led to 3D digital models produced with intraoral scanners (IOS), which can be manipulated easily for diagnosis, treatment planning, mockups, and a multitude of other uses. Combining 3D Printing with a 3D intraoral scan eliminates the need for physical storage but makes it to retrieve a 3D models for use within all dental modalities.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

The atmospheric lightning is one of the natural disasters which need to be considered in the sustainable development. The National Remote Sensing Centre (NRSC) has installed 46 lightning detection sensors (LDS) across the country. These sensors work in radio frequencies having their detection range up to 1000 km with more than 98% detection efficiency within 300 km range. The network is put in a way that sensors have about 50% sensor-to-sensor overlap in their detection ranges to enable high geolocation accuracy and maintain redundancy. The NRSC-LDS network (LDSN) estimates the current associated with each cloud to ground (CG) lightning flash which can be utilized for the risk assessment. The current estimates from one network to the other need to be inter-calibrated and harmonized. Present study compares the LDSN current estimates with Lightning Location Network (LLN) estimates and results are discussed with their impact on the estimation of vulnerable zones. A case study of lightning-induced fire event is presented to showcase the importance of the currents associated with lightning for future planning.

Clarifying hydrologic behavior, especially behavior related to extreme events such as flash floods, is vital for flood mitigation and management. However, discharge and rainfall measurement data are scarce, which is a major obstacle to flood mitigation. This study (i) simulated flash floods on a regional scale using three types of rainfall forcing implemented in a land surface model and (ii) evaluated and compared simulated flash floods with the observed discharge. The three types of rainfall forcing were those observed by the Automated Meteorological Data Acquisition System (AMeDAS) (Simulation I), the observed rainfall from the Ministry of Land, Infrastructure and Transportation (MLIT) (Simulation II), and the estimated rainfall from the Multi-purpose Transport Satellite (MTSAT), which was downscaled by AMeDAS rainfall (Simulation III). MLIT rainfall observations have a denser station network over the Ishikari River basin (spacing of approximately 10 km) compared with AMeDAS (spacing of approximately 20 km), so they are expected to capture the rainfall spatial distribution more accurately. A land surface model, Minimal Advance Treatments of Surface Interaction and Runoff (MATSIRO), was implemented for the flash flood simulation. The river flow simulations were run over the Ishikari river basin at a 1-km grid resolution and a 1-h temporal resolution during August 2010. The statistical performance of the river flow simulations demonstrated that Simulation I was reasonable compared with Simulation III. The findings also suggest that the advantage of the MTSAT-based estimated rainfall (i.e., good spatial distribution) can be coupled with the benefit of direct AMeDAS observations (i.e., representation of the true rainfall).

We consider a random dynamical system arising in a model of associative memory. This system can be seen as a small (stochastic and deterministic) perturbation of a determinstic system having two weak attractors which are destroyed after the perturbation. We show, with a computer aided proof, that the system has a kind of chaotic itineracy. Typical orbits are globally chaotic, while they spend relatively long time visiting attractor's ruins.

Fused deposition modeling (FDM) is widely applied in various fields due to its affordability and ease of use. However, it faces challenges such as achieving high surface quality, precise dimensional tolerance and overcoming anisotropic mechanical properties. This paper analyzes and compare the machinability of 3D printed PLA, PETG and carbon fiber reinforced PETG focusing on surface roughness and burr formation. A design of experiments (DoE) with a full factorial design was used, considering three factors: rotation speed, feed rate and depth of cut. Each factor had different levels: rotational speed at 3000, 5500 and 8000 rpm; feed rate at 400, 600 and 800 mm/min; and depth of cut at 0.2, 0.4, 0.6, and 0.8 mm. Machinability was evaluated by roughness and burr height using a profilometer for all the materials under the same milling conditions. To evaluate the statistical significance of the influence of various processing parameters on surface roughness and burr formation in 3D printed components made of three different materials PLA, PETG and carbon fiber reinforced PETG, an analysis of variance (ANOVA) test was conducted. This analysis investigated whether variations in rotational speed, feed rate and depth of cut resulted in measurable and significant differences in machinability results. Results showed that milling parameters significantly affect roughness and burr formation, with optimal conditions for minimizing any misalignment highlighting the trade-offs in parameter selection. These results provide insights into the post-processing of FDM-printed materials with milling, indicating the need for a balanced approach to parameter selection based on application-specific requirements.

Electrospinning is the versatile technique to generate large quantities of micro- or nano-fibers from a wide variety of shapes and sizes of polymer. Natural bone is a hierarchically composites with the dispersion of inorganic ceramic along organic polymer. The aim of this study, the electrospun poly (lactic acid) (PLA) mats coated with chitosan (CH) and calcium silicate (CS) powder were fabricated. The morphology, chemical composition, and surface properties of CS/CH-PLA composites were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. In vitro, the CS/CH-coated PLA mats increased the formation of apatite on the surface when soaking in cell cultured medium. During culture, the adhesion and proliferation of the human mesenchymal stem cells (hMSCs) cultured on CS/CH-PLA were significantly promoted relative to those on PLA. Collagen I and fibronectin levels and promoted cell adhesion were observed upon an increase in CS content. Further, compared to PLA mats without CS/CH, CS10 and CS15 mats markedly enhanced the proliferation of hMSCs as well as their osteogenesis properties, which was characterized by bone-related gene expression. Our results demonstrated that the biodegradable and electroactive CS/CH-PLA mats had potential application as an ideal candidate for bone tissue engineering. Together, findings from this study clearly demonstrated that PLLA-C2S composite scaffold may function as an ideal candidate for bone tissue engineering.

Oral cancer is a major public health burden worldwide. The lack of biomarkers for early diagnosis has increased the difficulty in managing this disease. Recent studies have reported that neutrophil gelatinase-associated lipocalin (NGAL), a secreted glycoprotein, is upregulated in various tumors. In our study we found that NGAL was significantly downregulated in primary malignant and metastatic tissues of oral cancer compared to normal tissues. The downregulation of NGAL was strongly correlated with the degree of differentiation and stage (I-IV), and can serve as a prognostic biomarker for oral cancer. Tobacco carcinogens were also found to be involved in the downregulation of NGAL. Mechanistic studies revealed that knockdown of NGAL increased oral cancer cell proliferation, survival, and migration, and also induced resistance against cisplatin. Silencing of NGAL activated mTOR signaling and reduced autophagy by the LKB1-AMPK-p53-Redd1 signaling axis. Moreover, cyclin-D1, Bcl-2, and MMP-9 were upregulated, and caspase-9 was downregulated, suggesting that silencing of NGAL increases oral cancer cell proliferation, survival, and migration. Thus, from our study it is evident that downregulation of NGAL activates the mTOR pathway and helps in the progression of oral cancer.

The present study drops the line for the flow characteristics of fly ash-based (FA) geopolymers reinforced with polypropylene (PP) fibers undergoing the extrusion process during three-dimensional printing. Applying to the Herschel-Bulkley rheological model the research is ready with the sound theoretical basis which is used to understand the flow behavior of these materials under various conditions. A combination of experimental and numerical techniques that are based on the Finite Element Method (FEM) in COMSOL has been used in this study. The results of both the experimental and simulation approaches are then compared and the behavior of the material during extrusion is then examined. The experimental results proved PP fiber content has significant effects on rheological properties. The experiments on mixes which are either devoid of fibers or possess a high content of fiber, encountered problems like a high static yield stress and material segregation. Mixes with fibers of moderate content showed smoother extrusion processes, which means that a suitable range of fiber addition exists for the fibers that optimally balance the mechanical properties and extrudability. Numerical simulations typically agreed with experimental data for fiber contents up until it reached a certain level but not above, suggesting the existence of more complex interactions inside the fibers and the necessity for the subsequent model refinements. The investigation outlines a 0.25% and 0.5% fiber content range that leads to enhanced performance without bringing the extrusion process to greater complications and further making the production of proper, architecturally printed structures possible.