The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

In this paper, we aim to present real implementation cases where non-visible elements of environmental impact assessments (EIA), wind flow, are visualized using a 3D digital twin technology. The conventional EIA process serves as a crucial tool in the evaluation of potential environmental impacts prior to the initiation of development projects. This evaluation helps to establish a legal and institutional framework that seeks to minimize the adverse effects on the environment. However, traditional EIA methods present challenges, particularly for non-experts, in comprehending the results of assessments involving non-visible environmental factors such as noise, air quality, and wind flow. These elements are often represented in static images or numerical tables, limiting accurate understanding and engagement. Our proposed method, termed Digital Twin based EIA, addresses these limitations by leveraging digital twin technology. This advanced methodology allows for the visualization of non-visible environmental elements in a spatio-temporal dimension, providing a more interactive and comprehensive user interface/experience for both citizens and stakeholders. In this context, we present a unique case study that focuses on visualizing wind flow using this technology. This paper serves as an example of how digital twin platforms can enhance traditional EIA processes, offering a more immersive and informative experience. The evolution of EIA into the digital realm signifies an important step forward in fostering public understanding and engagement in environmental protection efforts.

Thermal infrared imagery provides temperature information on target objects, and has been widely applied in non-destructive testing. However, thermal infrared imagery is not always able to display detailed textures of inspected objects, which hampers the understanding of geometric entities consisting of temperature information. Although some commercial software has been developed for 3D thermal model displays, the software requires the use of expensive specific thermal infrared sensors. This study proposes a cost-effective method for 3D thermal model reconstruction based on image-based modeling. Two smart phones and a low-cost thermal infrared camera are employed to acquire visible images and thermal images, respectively, that are fused for 3D thermal model reconstruction. The experiment results demonstrate that the proposed method is able to effectively reconstruct a 3D thermal model which extremely approximates its corresponding entity. The total computation time for the 3D thermal model reconstruction is intensive while generating dense points required for the creation of a geometric entity. Future work will improve the efficiency of the proposed method in order to expand its potential applications to in-time monitoring.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

The lithium-ion batteries are widely used as a power source for portable devices, including cell phones. The useful life is about 2 years or 500 cycles, contributing to the generation of waste from electrical and electronic equipment (WEEE). Mining of lithium and cobalt damages the environment and is onerous; therefore, sustainable alternatives, such as obtaining these elements from secondary sources as recycling of lithium-ion batteries, are essential to provide the inputs used in the sector. However, the metallurgical route which will used to recovering them must be considered, due to this work aims for a more environmentally favorable process using DL-malic acid 1.5 M and instead of compared with sulfuric acid 2 M, heat pretreatment of 1 h and 3 h, and for all conditions, experiments were carried out with and without adding the oxidizing agent hydrogen peroxide. The best yields occurred in presence of H2O2 10 % v/v, and heat pretreatment of 1 h: 33.49 % Co and 4.63 % Li, and 29.78 % Co e 3.44 % Li were recovered by sulfuric acid and DL-malic acid, respectively.

Epithelial–mesenchymal transition (EMT) is defined as a cellular process during which epithelial cells acquire mesenchymal phenotypes and behavior following the downregulation of epithelial features. EMT and its reversed process, the mesenchymal-epithelial transition (MET), and the special form of EMT, the endothelial-mesenchymal transition (EndMT), have been thought as a universal dogma controlling developmental and pathological processes. More than half a century of EMT study has made it a large research field and a mainstream concept. However, discrepancies and disputes over EMT and EMT research have also grown over time. Particularly, neither the epithelial and mesenchymal states/properties nor their regulatory networks nor specific markers have been defined, rendering the EMT, MET and EndMT concepts groundless. Moreover, EMT and MET effects should not be a cause, but rather a consequence of or an accompanying effect during developmental and pathological processes. EMT and MET represented by the change in cell shapes or adhesiveness or symbolized by EMT factors are biased interpretation of the overall change in cellular property and regulatory networks during development and cancer progression. The true meaning of EMT effects in some developmental and pathological processes, such as fibrosis, needs re-evaluation. But the core EMT factors are actually a few components of the regulatory networks of neural stemness, which determines tumorigenicity and pluripotency. The EMT effects in cancer progression and neural crest formation are wrong attribution of the role of neural stemness during cancer progression and the cell-intrinsic property of neural crest cells to the unknown mesenchymal state. It is time to reassess the significance of EMT and its related concepts in scientific research.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Diseases in articular cartilages have affected millions of people globally. Although the biochemical and cellular composition of articular cartilages is relatively simple, there is the limitation in self-repair ability of cartilage. Therefore, developing the strategies for cartilage repair is very important. Here, we reported a new manufacturing process of water-based polyurethane based photosensitive materials with hyaluronic acid and applied the materials for 3D printed customized cartilage scaffolds. The scaffold has high cytocompatibility and is one that closely mimics the mechanical properties of articular cartilages. It is suitable for culturing human Wharton's jelly mesenchymal stem cells (hWJMSCs) and the cells showed an excellent chondrogenic differentiation capacity. We consider that the 3D printing hybrid scaffolds may have potential in customized tissue engineering and facilitate the development of cartilage tissue engineering.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

The paper presents the design and the implementation of different advanced control strategies that are applied to a nonlinear model of a thermal unit. A data–driven grey–box identification approach provided the physically meaningful nonlinear continuous–time model, which represents the benchmark exploited in this work. The control problem of this thermal unit is important since it constitutes the key element of passive air conditioning systems. The advanced control schemes analysed in this paper are used to regulate the outflow air temperature of the thermal unit by exploiting the inflow air speed, whilst the inflow air temperature is considered as an external disturbance. The reliability and robustness issues of the suggested control methodologies are verified with a Monte–Carlo analysis for simulating modelling uncertainty, disturbance and measurement errors. The achieved results serve to demonstrate the effectiveness and the viable application the suggested control solutions to air conditioning systems. The benchmark model represents one of the key issues of this study, which is exploited for benchmarking different model–based and data–driven advanced control methodologies through extensive simulations. Moreover, this work highlights the main features of the proposed control schemes, while providing practitioners and heating, ventilating and air conditioning engineers with tools to design robust control strategies for air conditioning systems.

Most of the phase change materials (PCMs) have been limited to use as functional additions or sealed in containers, and extra auxiliary equipment or supporting matrix is needed. The emergence of 3D printing technique has dramatically advanced the developments of materials and simplified production processes. This study focuses on a novel strategy to model thermal energy storage crystalline gels with three-dimensional architecture directly from liquid resin without supporting materials through light-induced polymerization 3D printing technique. A mask-projection stereolithography printer was used to measure the 3D printing test, and the printable characters of crystalline thermal energy storage P(SA-DMAA) gels with different molar ratios were evaluated. For the P(SA-DMMA) gels with small fraction of SA, the 3D fabrication was realized with higher printing precision both on mili- and micro-meter scales. As a comparison of 3D printed samples, P(SA-DMAA) gels made by other two methods, post-UV curing treatment after 3D printing and UV curing using conventional mold, were prepared. The 3D printed P(SA-DMAA) gels shown high crystallinity. Post–UV curing treatment was beneficial to full curing of 3D printed gels, but did not lead to the further improvement of crystal structure to get higher crystallinity. The P(SA-DMAA) crystalline gel having the highest energy storage enthalpy that reached 69.6 J·g⁻¹ was developed. Its good thermoregulation property in the temperature range from 25 to 40 °C was proved. The P(SA-DMAA) gels are feasible for practical applications as one kind of 3D printing material with thermal energy storage and thermoregulation functionality.

The development of new turbomachinery designs requires numerous time-consuming and computationally intensive computational fluid dynamics (CFD) calculations. However, most of the generated high spatial resolution data remains unused at later development steps. That is also the case with automated optimization processes that use only a few integral values to determine objectives and constraints. Therefore the development of a data-driven AI model was initiated to ensure the potential of further use of the CFD data which is also used to train the AI model. The presented method subsequently provides a fast approximation of the 3D flow for new designs. In this paper, the structure of the developed AI model is presented and the approximation quality is analysed using a complex, state-of-the-art compressor test case. It is shown that the AI model can reproduce many characteristics of the 3D flow of new designs, and performance measures such as efficiency can be derived from these flow predictions. In addition, the complex test case revealed that greater design variation reduces the AI approximation quality which can lead to undesirable exploratory behaviour in an optimisation setup. Overall, the test case has shown promising results and has provided hints for further improvements of the AI model.

The result of the multidisciplinary collaboration of researchers from different areas of knowledge to validate a solar radiation model is presented. The MAPsol is a 3D local-scale adaptive solar radiation model that allows to estimate direct, diffuse and reflected irradiance for clear sky conditions. The model includes the adaptation of the mesh to complex orography and albedo, and considers the shadows cast by the terrain and buildings. The surface mesh generation is based on surface refinement, smoothing and parameterisation techniques and allows the generation of high quality adapted meshes with a reasonable number of elements. Another key aspect of the paper is the generation of a high-resolution digital elevation model (DEM). This high-resolution DEM is constructed from LiDAR data and its resolution if two times more accurate than the publicly available DEMs. The validation process uses direct and global solar irradiance data obtained from pyranometers at the University of Salamanca located in an urban area affected by systematic shading from nearby buildings. This work provides an efficient protocol for studying solar resources, with particular emphasis on areas of complex orography and dense buildings where shadows can potentially make solar energy production facilities less efficient.

Graph visualization has evolved significantly over time, offering various methods to effectively represent complex data structures. This study introduces a novel force-directed algorithm for 3D data visualization, specifically tailored for commonly used datasets in linked data visualization. Leveraging the power of graph theory and methods, the algorithm aims to address the challenge of creating visually appealing and easily interpretable visualizations, which often necessitate advanced user interaction. By utilizing 3D space and the Unity Engine, the research successfully visualizes data and develops interactive visualizations, overcoming limitations of basic force-directed implementations. The main contribution of presented research is in the force-directed algorithm with springs and controlled placement as a visualization technique that combines the use of springs and attractive forces to stabilize a graph in a 3D environment. The combination of these two techniques also helps prevent the formation of a single large cluster within the graph, enhancing the overall visualization quality.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Corneal opacity is a leading cause of vision impairment and suffering worldwide. Transplantation can effectively restore vision and reduce chronic discomfort. However, there is a considerable shortage of viable corneal graft tissues. Tissue engineering may address this issue by advancing xeno- keratoplasty as a viable alternative to conventional keratoplasty. In particular, livestock decellularization strategies offer the potential to generate bioartificial ocular prosthetics in sufficient supply to match existing and projected needs. To this end, we have examined the best practices and characterizations that have supported the current state-of-the-art driving preclinical and clinical applications. Identifying the challenges that delimit activities to supplement the donor corneal pool derived from acellular scaffolds allowed us to hypothesize a model for keratoprosthesis applications derived from livestock combining 3D printing and decellularization.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Through performance analysis using four years of operational data, we achieved a Coefficient of Performance (COP) of 5 on the building load side. This paper confirms the equivalence of the dimensionless production temperature and heat recovery rate, observing nearly identical changes in the dimensionless production temperature over four cycles (eight seasons). Furthermore, we propose an operational method for the following fiscal year that maintains the balance between accumulated storage quantity and pumping volume, based on predictions from this plant's operational pattern.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

The condensing heat exchanger is commonly applied in various heat exchange systems. It can efficiently recover moisture and heat from the flue gas that contains water vapor. However, the convective-condensation heat transfer process is so complicated that no mature thermal calculation model is available. This study develops a thermal calculation model for the widely employed tubular condensing heat exchanger in industry. To characterize the degree of the heat and mass transfer, this study introduces two parameters, namely the sensible and latent heat transfer efficiencies of fin. The thermal calculations are conducted for the condensing heat exchangers reported in the literature to verify the proposed model by comparing it with the experimental data. The results show that the absolute error of the calculated sensible and latent heat transfer efficiencies is 0.0365 and 0.0268, respectively. Under the working conditions in this study, a maximum difference of 5.2 K has been acquired between the measured and calculated values of the outlet temperature. The relative error of the condensate water flowrate is mostly within ±5.0% and ±10.0% under the bare-tube and finned-tube conditions, respectively, with a maximum deviation of 0.7 and 1.4 kg h-1. This study provides a general model for designing and optimizing various tubular condensing heat exchangers accurately.

The quest for youthful, healthy skin and full, vibrant hair has long been a driving force in the dermocosmetics field. However, traditional approaches often struggle to address the underlying causes of aging, damage, and hair loss. Regenerative cosmetics, powered by skin tissue engineering, offer a transformative alternative. This review explores the emerging field of using engineered skin tissues for cosmetic purposes, focusing specifically on their potential for anti-aging, repair, and hair restoration applications. We discuss how these technologies aim to rejuvenate aging skin by promoting collagen production, reducing wrinkles, and improving overall skin function. Additionally, the use of engineered skin for wound healing and scar reduction is examined, highlighting their potential to improve the appearance and functionality of damaged skin. Finally, we advance the exciting prospects of utilizing skin tissue engineering techniques to regenerate hair follicles, potentially offering solutions for hair loss and promoting denser hair growth.

Dynamic thermogravimetric (TG) analysis under nitrogen environment was used to understand the thermal decomposition process of 3D printing filaments made of wood-filled polylactic acid (PLA)/starch blend. The characteristic temperatures and apparent activation energy (AAE) of the filaments with various starch contents were calculated with well-known kinetic models by Friedman, Flynn-Wall-Ozawa, Coats-Redfern and Kissinger. With the increased starch content in the filament, the onset thermal decomposition temperatures of the filaments decreased gradually from 272.4 to 155.1°C. The thermal degradation degree became smaller, and the transitional temperature interval became larger with increased starch proportion. The AAE values of the three types of filaments with different starch ratios varied between 97 kJ/mol and 114 kJ/mol, depending on material composition and method of calculation. The improved understanding of thermal decomposition behavior of PLA-starch-wood composites can help develop more biodegradable PLA/starch-based filaments for 3D printing.

Purpose: Localization and mapping with LiDAR data is a fundamental building block for autonomous vehicles. Though LiDAR point clouds can often encode the scene depth more accurate and steadier compared with visual information, laser-based Simultaneous Localization And Mapping (SLAM) remains challengeable as the data is usually sparse, density variable and less discriminative. The purpose of this paper is to propose an accurate and reliable laser-based SLAM solution. Design/methodology/approach: The method starts with constructing voxel grids based on the 3D input point cloud. These voxels are then classified into three types to indicate different physical objects according to the spatial distribution of the points contained in each voxel. A global environment model with Partition of Unity (POU) implicit surface is maintained along the process and located voxels are merged into it from stage to stage, through scan-to-model matching implemented by Levenberg-Marquardt method. Findings: We find a laser-based SLAM method. The method uses POU implicit surface representation to build the model and is evaluated on the KITTI odometry benchmark without loop closure. Experimental results indicate that the method achieves accuracy comparable to the state-of-the-art methods. Originality/value: We propose a novel, low-drift SLAM method, which falls into a scan-to-model matching paradigm, operates on point clouds obtained from Velodyne HDL64. The method is of value to researchers developing SLAM systems for autonomous vehicles.

With the pressure of the increasing density of urban areas, some public infrastructures are moving to the underground to free up space above, such as utility lines, rail lines and roads. In the big data era, the three dimensional (3D) data can be beneficial to understand the complex urban area. Comparing to spatial data and information of the above ground, we lack of the precise and detailed information about underground infrastructures, such as the spatial information of underground infrastructure, the ownership of underground objects and the interdependence of infrastructures in the above and below ground. How to map reliable 3D underground utility networks and use it in the land administration? First, to explain the importance of this work and find a possible solution, this paper observes the current issues of the existing underground utility database in Singapore. A framework for utility data governance is proposed to manage the work process from the underground utility data capture to data usage. This is the backbone to support the coordination of different roles in the utility data governance and usage. Then, an initial design of the 3D underground utility data model is introduced to describe the 3D geometric and spatial information about underground utility data and connect it to the cadastral parcel for land administration. In the case study, the newly collected data from mobile Ground Penetrating Radar is integrated with the existing utility data for 3D modelling. It is expected to explore the integration of new collected 3D data, the existing 2D data and cadastral information for land administration of underground utilities.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

Hormones must be balanced and dynamically controlled for the Female Reproductive Tract (FRT) to function correctly during the menstrual cycle, pregnancy, and delivery. Gamete selection and successful transfer to the uterus, where it implants and pregnancy occurs, is supported by the mucosal epithelial lining of the FRT ovaries, uterus, cervix, fallopian tubes, and vagina. Successful implantation and placentation in humans and other animals rely on complex interactions between the embryo and a receptive female reproductive system. The FRT's recent breakthroughs in three-dimensional (3D) organoid systems now provide critical experimental models that match the organ's physiological, functional, and anatomical characteristics in vitro. This article summarizes the current state of the art on organoids generated from various parts of the FRT. The current analysis examines recent developments in the creation of organoid models of reproductive organs, as well as their future directions.

Traditional 3D reconstruction models have consistently encountered a challenge: attaining high recall of object edges while preserving precision. In this paper, we introduce a post-processing method Multi-Head Attention Refiner (MA-R) aimed at tackling this challenge by integrating a multi-head attention mechanism within the U-Net style refiner module. The 3D reconstruction model applying this method demonstrates excellence in parsing intricate image details, resulting in significant enhancement of boundary predictions and increased recall rates. In our experiments, our method significantly enhances the reconstruction performance of Pix2Vox++ when multiple images are utilized as input. Specifically, it achieves an enhanced Intersection Over Union score of approximately 1.1% compared to the original Pix2Vox++ model when 16-view images are employed.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, researchers developed efficient aqueous nanofluid conductors. Carbon nanotubes (CNTs) are widely studied to reach efficient, stable, low-cost and environmentally-friendly aqueous-nanofluids. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain literature mechanisms behind improvement. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluids as desired.

Pyrocumulonimbus (pyroCb) thunderclouds, produced from extreme bushfires, can initiate frequent cloud-to-ground (CG) lightning strikes containing extended continuing currents. This, in turn, can ignite new spotfires and inflict massive harm on the environment and infrastructures. This study presents a 3D numerical thundercloud model for estimating the lightning of different types and its striking zone for the conceptual tripole thundercloud structure which is theorized to elucidate the lightning phenomenon in pyroCb storms. More emphasis is given to the lower positive charge structure thundercloud to thoroughly examine various electrical parameters including the longitudinal electric field, electric potential, and surface charge density. The simulation outcomes on pyroCb thunderclouds with a tripole structure confirm the presence of negative longitudinal electric field initiation at the cloud’s lower region. This initiation is accompanied by enhancing the lower positive charge region, resulting in an overall positive electric potential increase. Consequently, negative surface charge density appears underneath the pyroCb thundercloud which has the potential to induce positive cloud-to-ground (+CG) lightning flashes. The suggested model would establish the basis for identifying the potential area impacted by lightning and could also be expanded to analyze the dangerous conditions that may arise in wind energy farms or power substations in times of severe pyroCb events.

The monocular structured light measurement system has low cost, simple algorithms, and a wide measurement range, making it widely applicable in multiple fields. However, in practical applications, the system may be affected by various factors including noise, non-linear intensity, changes in the reflectivity of the object being measured, and the calibration method and accuracy of the system, thereby reducing the measurement accuracy. In order to solve these issues, this paper proposes a new monocular structured light measurement method, mainly comprises the following two points: (a) A denoising algorithm for phase images based on DAE is proposed, which calculates the wrapped phase of the phase-shifted fringes after initial denoising by DAE. Then, a new phase-shifted fringe pattern is generated and input into DAE for iterative denoising, achieving high-performance image denoising and high-precision wrapped phase solution. (b) A new absolute phase height calibration algorithm is proposed, which introduces camera internal and external parameters and uses a two-layer feedforward network to directly establish the relationship between phase and the 3D coordinate system. Without the need for high-precision motion platforms, high-precision phase height calibration is attainable. In general, compared to conventional methods, the experimental results indicate the effectiveness of the proposed method for low-quality phase-shifted fringe 3D reconstruction. In addition, the measurement method described in this article also demonstrates effectiveness in high-dynamic scenes.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Elbow dislocation and instability present significant clinical challenges, necessitating a thorough understanding of the underlying bio-mechanical mechanisms. In this study, a quasi-static three-dimensional finite element model of the human elbow joint is developed to investigate stress distribution and stages of dislocation in the human elbow under various loading conditions. The model simulates the elbow joint in different degrees of flexion (30°, 45°, 60°, and 90°) and forearm positions (pronation and supination), providing detailed insights into the progression of dislocation. Significant findings include the identification of high stress concentrations on the humerus at 90° flexion and on the radial and coronoid processes at 30°, 45°, and 60° flexion. Three reproducible stages of dislocation were observed, particularly in flexed positions with forearm pronation or supination. These stages align with experimental observations and highlight the initial occurrence of bony failures, such as radial head and ulnar coronoid fractures, preceding soft tissue tears. Clinically, the study underscores that early-stage low-impact posterior elbow dislocations retain enough stability to be managed with closed reduction and early mobilization. However, as dislocations progress, significant damage to the medial and lateral collateral ligaments is expected, necessitating more invasive treatments. This research provides valuable bio-mechanical insights into elbow dislocation, aiding in the development of improved treatment strategies and enhancing patient outcomes through precise and timely clinical interventions. The validated FEM serves as a powerful tool for pre-surgical planning offering a comprehensive understanding of elbow joint mechanics.

This research is completed in development of researches devoted to relations between elastic modulus (MoE) and thermal expansivity (CTe) of different materials. This study experimentally confirmed the relation of MoE and CTe for thermosetting polymers and FRPs both under normal and heating temperatures. As the thermosetting polymers, the epoxy compositions were used and glass fiber and mineral additives for FRP. The experiment was based on dilatometric and elastic deformations’ testing. Also, the relaxation model of MoE/CTe was proposed, that is based on physical properties of polymers’ supramolecular structures. The comparative analyzing of MoE/CTes’ different models is done. The most accurate models are determined, and the relaxation model has demonstrated the high accuracy.

Anaerobic digestion is a biological process that transforms high-strength organic effluents into biogas with multiple benefits. However, concurrent with organics' biological transformation, a liquid phase with a high solid content is also derived from this process. Valorizing this fraction is not an easy task if an agronomic application cannot be considered as a suitable option. The thermal valorization of this fraction allows for energy extraction, but also gives rise to additional capital investment and increases the energy demand of the global process. In addition, the thermal treatment of digestate has to deal with a mineralized material. The changes in organic matter due to anaerobic stabilization were studied in the present manuscript, by evaluating the thermal behavior of samples, activation energy and organic transformation using FTIR spectroscopy. Digested samples of a mixture composed of manure and glycerin (5% v/v) were studied. The stabilization caused a dramatic decrease in aliphatic compounds, greatly increasing the mineral content of the sample. Thermal valorization of digestates must consider the lower energy content and more complex structure of these materials, with higher content of lignin and protein-type compounds.

Despite being small and simple structured in comparison to their victims, virus particles have the potential to harm severly and even kill highly developed species such as humans. To face upcoming virus pandemics, detailed quantitative biophysical understanding of intracellular virus replication mechanisms is inevitable. Unveiling the relationship of form and function might allow to determine putative attack points relevant for the systematic development of direct antiviral agents (DAA) and potent vaccines. Biophysical investigations of spatio-temporal dynamics of intracellular virus replication so far are rare. We are developing a framework to allow for fully spatio-temporal resolved virus replication dynamics simulations based on partial differential equations models (PDE) and evaluated with advanced numerical mathematical methods on leading supercomputers. This study presents an advanced highly nonlinear model of the genome replication cycle of a specific RNA virus, the Hepatitis C virus (HCV). The diffusion-reaction model mimics the interplay of the major components of the viral RNA (vRNA) cycle, namely non structural viral proteins (NSP), vRNA and a generic host factor. Technically, we couple surface PDEs (sufPDEs) on the 3D embedded 2D Endoplasmatic Reticulum (ER) manifold with PDEs in the 3D membranous web (MW) and cytosol volume. (The MWs are the replication factories growing on the ER induced by NSPs.) The sufPDE/PDE model is evaluated at realistic reconstructed cell geometries which are based on experimental data. The simulations couple the effects of NSPs which are restricted to the ER surface with effects appearing in the volume. The volume effects include the host factor supply from the cytosol and the MW dynamics. Special emphasis is put to the exchange of components between ER surface, MWs and cytosol volume. As the vRNA spatial properties are not fully understood so far in experiment, the model allows for vRNA both restricted to the ER and moving in the cytosol. The visualization of the simulation resembles a look into some sort of fully 3D resolved “in silico microscopes” to mirror and complement in vitro / in vivo experiments for the intracellular vRNA cycle dynamics. The output data are quantitatively consistent with experimental data and provoke advanced experimental studies to validate the model.

In this paper, we propose a methodology for analyzing the near-field coupling between two surface mount device (SMD) inductors using a 3-dimensional electromagnetic (3D-EM) model. To develop the 3D-EM model, we first extract the effective permeability of core magnetic material in the SMD using the loss tangent in the equivalent circuit model. Then the effective permeability is used in the magnetic material for the 3D-EM modeling of SMD inductor. The validity of the proposed 3D-EM model is confirmed by comparing the impedance and S-parameters obtained from both measured and EM-simulated values for the two near-field coupled SMDs. Finally, the near-field coupling effects between the two adjacent SMD inductors are visualized in terms of magnetic coupling path visualization (CPV) using the proposed 3D-EM model, which demonstrates its usefulness for near-field coupling analysis.

The expansion of concrete subjected to extreme elevated temperature is linked with intricate micro-structural variations, such as the transformation of the constituent phases. This study proposes a model to predict the thermal expansion of cement paste and concrete considering micro-structural changes under elevated temperatures ranging from 20°C to 800°C. The model presented can consider characteristics of various aggregates in the calculation of thermal expansion for concrete. The model is a combination of a multi-scale stoichiometric model and a multi-scale composite model. At the cement paste level, the model satisfactorily predicted a test result. At concrete level, upper bounds from the model were matched relatively well with test results by previous researcher. If the mechanical properties, such as elastic modulus (E), Poisson’s ratio (ν), and thermal deformation, of the aggregates used in concrete are given, it is likely that the model will reasonably predict experimental results.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

This study presents the design and comprehensive 3D multiphysics simulation of a novel microfluidic immunosensor for real-time, non-invasive monitoring of pro-inflammatory biomarkers in human sweat. The patch-like device, designed using COMSOL Multiphysics, integrates magnetofluidic manipulation with direct-field capacitive sensing. The sensor comprises two distinct units: an immunocomplex enhancement unit, employing a series of microcoils to optimize the binding efficiency, reaction kinetics, and homogeneity of biomarker-magnetic nanoparticle (MNP) interactions, thereby enhancing the sensor's specificity; and a layered capacitive sensing unit, designed to concentrate and detect biomarker-tagged MNPs, thus amplifying sensitivity. Simulations of the capacitive sensing unit revealed a substantial sensitivity increase of up to 42.48\% at an 85\% MNP concentration within the detection zone. These findings highlight the potential of the proposed immunosensor for efficient and precise real-time biomarker monitoring, which may facilitate early disease diagnosis and enable personalized healthcare interventions.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

For a fiber optic gyroscope, thermal deformation of the fiber coil can introduce additional ther-mal-induced phase errors, commonly referred to as thermal errors. Thermal error compensation techniques are effective means of addressing this issue. The principle behind these techniques involves real-time sensing of thermal errors and correcting them within the output signal. Since it is challenging to directly separate thermal errors from the output signal of the fiber optic gyro-scope, it is necessary to predict thermal errors based on temperature. To establish a mathematical model between temperature and thermal errors, this paper measured synchronized data of phase errors and angular velocity for the fiber coil under different temperature conditions and aimed to model it using data-driven methods. Due to the difficulty of conducting tests and the limited number of data samples, an algorithm called TD-model modeling is proposed to address the issue of overfitting, which can reduce the model's generalization ability. First, a theoretical analysis of the phase errors caused by thermal deformation of the fiber coil is performed. Subsequently, the critical parameters, such as the thermal expansion coefficient, are determined, and a theoretical model is established. Finally, the theoretical analysis model is incorporated as a regularization term and combined with the test data to jointly participate in the regression of model coefficients. Through experimental comparative analysis, it is shown that, relative to ordinary regression models, the TD-model effectively mitigates overfitting caused by the limited number of samples, leading to a 58% improvement in predictive accuracy.

Lightning strike can cause a considerable damage in aircraft parts made from semiconducting materials such as Carbon Fiber Reinforced Plastics (CFRPs). Therefore, in recent years, the lightning strike phenomenon has attracted the interest of the academic community and the aircraft industry. Until now, the problem has been addressed mainly experimentally, while the reported numerical works are very limited. In the present work, a coupled electro-thermal FE model has been developed using the ANSYS commercial FE code to simulate the lightning strike damage in unidirectional CFRP laminates due to the Joule heat flux phenomenon. The model is based on the SOLID69 thermoelectric element and applies a non-linear, time-transient analysis. The main input to the model is the thermal-electrical properties of the composite material which vary with temperature. Using the model, a parametric study on the effect of mesh density and peak intensity on the thermal damage has been performed. Three electrical lightning strikes of low (10 kA), medium (30 kA) and high peak intensity (40 kA) have been applied according to the SAE ARP 5412 standard. The electro-thermal model has been validated against a numerical model from the literature. The numerical results reveal that the increase of peak intensity leads to the increase of the area and penetration depth of matrix thermal damage (pyrolysis) as well as to the increase of the area of fiber damage (deterioration and ablation). Through progressive damage modeling, the residual tensile strength of the CFRP plate after being subjected to lightning strike of different peak intensity has been predicted. Lightning strike initial damage has been simulated by translating the thermal field into degradation of elastic properties of the lamina. The results show an increase in the accumulated matrix damage and a decrease of tensile strength due to the initial lightning strike damage. For the maximum peak intensity of 40 kA, a decrease in tensile strength of 4.8% has been predicted

In this paper, a geometric body-centered model to simulate the periodic structure of unidirectional fibrous composites is presented. To this end, three prescribed configurations are introduced to predict in a deterministic manner the arrangement of internal and neighboring fibers inside the matrix. Thus, three different representative volume elements (RVEs) are established. Furthermore, the concept of the interphase has been taken into account, stating that each individual fiber is encircled by a thin layer of variable thermomechanical properties. Next, these three unit cells are transformed in a unified manner to a coaxial multilayer cylinder model. This advanced model includes the influence of fiber contiguity in parallel with the interphase concept on the thermomechanical properties of the overall material. Then, by the use of this model, the authors propose explicit expressions to evaluate the longitudinal and transverse thermal conductivity of this type of composite. The theoretical predictions were compared with experimental results, as well as with theoretical values yielded by some reliable formulae derived from other workers, and a reasonable agreement was found.

In recent years, with the development of social media, people are more and more inclined to upload text, pictures and videos on the platform to express their personal emotions, thus the number of short videos is increasing and becoming the first choice for people to socialize. Unlike the traditional way, people can convey their personal emotions and opinions through media other than words, such as video images, etc. for external information. Therefore, the expression and analysis of emotions is not only through text, but also through the analysis of emotional needs in images and videos, and the research scholars have customized products for individual users. Compared with pure text content, video information can more intuitively express users' happiness, anger and sorrow, thus short video-related applications have gained more and more popularity among Internet users in recent years. However, not all short videos on social networking sites can accurately express users' emotions, and related text information can more accurately assist sentiment analysis and thus improve accuracy. However, short video sentiment analysis based on video frame images is inaccurate in some scenarios, such as when expressing tears of joy, the sentiment expressed by the user's facial expression and voice are different, which will cause errors in the analysis of sentiment. As a result, researchers began to consider multimodal sentiment analysis to reduce the impact of the above scenarios on short video sentiment analysis. This paper focuses on proposing a sentiment analysis method for short videos. We first propose a residual attention model to make full use of the information in audio to classify the emotions contained in them. Then the text information in the dataset is classified by feature extraction. The key to extract features from text information is not only to retain the semantic information of the text, but also to explore the potential emotional information in the text, so as to ensure the integrity of the text information features. The experiments show that the sentiment analysis model proposed in this paper is more superior than the baselines.

Development of novel anti-cancer peptides requires a rapid screening process which can be accelerated by using appropriate in vitro tumor models. Breast carcinoma tissue is a three dimensional (3D) microenvironment, which contains a hypoxic center surrounded by dense proliferative tissue. Biochemical clues provided by such 3D cell mass cannot be recapitulated in conventional 2D culture systems. In this experiment, we evaluate the efficacy of the sandalwood peptide, cyclosaplin on established in vitro 3D silk breast cancer model using invasive MDA-MB-231 cell line. The anti-proliferative effect of the peptide on 3D silk tumor model is monitored by alamar blue assay, with conventional 2D culture as control. The proliferation rate, glucose consumed, LDH, and MMP-9 activity of Human breast cancer cells are higher in 3D constructs compared to 2D. A higher concentration of drug is required to achieve 50% cell death in 3D culture than 2D cultures. The cyclosaplin treated MDA-MB-231 cells showed significant decrease in MMP-9 activity in 3D constructs. Microscopic analysis revealed the formation of cell clusters evenly distributed in the scaffolds. The drug treated cells were less in number, smaller and showed unusual morphology. Overall, these findings indicate the role of cyclosaplin as a promising anti-cancer therapeutics.

The digital elevation model (DEM) is one of the key geospatial datasets used in many fields of engineering and science for countless applications. In this contribution, we assess the vertical accuracy of the Advanced Land Observing Satellite (ALOS) World 3D-30m (AW3D30) DEM using the runway method (RWYM). The RWYM utilizes the longitudinal profiles of runways which are reliable and ubiquitous reference data. A reference dataset used in this project consists of 36 runways located at various points throughout the world. The same dataset was previously used to test the accuracy of WorldDEM^TM. Our study indicates that AW3D30 has a remarkably high RMSE of 1.78 m (one σ). However, while analyzing the results, it has become apparent that it also contains a widespread elevation anomaly. We conclude that this anomaly is the result of uncompensated sensor noise and the data processing algorithm (downsampling of the higher resolution data). We believe that this issue should be communicated to the user community. Also, we would like to note that the traditional accuracy assessment of a DEM, e.g., statistical assessment of the elevation differences = model – reference, does not allow for identification of these type of anomalies in a DEM.

Tailings generated by mining account for the largest proportion of global waste from industrial activities. Copper is relatively uncommon world-wide, with low concentrations in sediments and waters, yet is very elevated around mining sites. On the Keweenaw Peninsula of Michigan, USA, jutting out into Lake Superior, 140 mines extracted native copper from the Portage Lake Volcanic Series, part of an intercontinental rift system. Between 1901-1932, two mills at Gay (Mohawk, Wolverine) sluiced 22.7 million metric tonnes (MMT) of copper-rich tailings (stamp sands) into Grand (Big) Traverse Bay. Here we examine: 1) 3D coastal elevation and reef bathymetry, 2) particle dispersal, 3) copper concentrations and leaching, plus 4) shoreline toxicity. About 10 MMT of tailings created a migrating coastal beach that stretches 7 km from the Gay pile to the Traverse River Seawall. Another 10 MMT are moving underwater on the coastal shelf, threatening Buffalo Reef, an important lake trout and whitefish breeding ground. Aerial photos, ALS (plane) LiDAR, and relatively inexpensive UAS (drone) surveys characterize shoreline structure and aid initial remediation. Because sands (natural beach quartz, stamp sand basalt) are silicates of similar density, particle dispersal is similar and challenging. However, stamp sand beaches contrast greatly with natural sand beaches in both physical profile and chemistry. Dispersing particles retain copper, and release toxic concentrations. Leaching is elevated by exposure to high DOC and low pH waters. Field experiments, shoreline seining, and benthic sampling confirm serious impacts on aquatic biota, supporting tailings removal.

Objective: The aim of this in vitro study was to evaluate the accuracy of resin-based fixed dental restorations, namely veneers, single crowns, and four-unit fixed partial dental prosthesis (FPDs) using two different 3D printers and polymer-based materials. Materials and Methods: A standard maxillary polyurethane jaw model containing prepared teeth was scanned using an intraoral scanner. The generated STL data were used to design the restorations virtually using CAD software. Two 3D printers were utilized for the provisional digital light processing and stereolithography for the castable resin patterns. Each printer produced 10 specimens of each type of restoration, for a total of 80 restorations. The 3d-printed restorations were then 3D scanned using the same intraoral scanner and evaluated for external and internal dimensional accuracy in terms of trueness and precision. A one-way ANOVA and Two-sample T-Test were implemented to compute the precision (variability between groups) and trueness (with the designed CAD model). A level of statistical significance of p-Value

Atopic dermatitis (AD) is a chronic inflammatory disorder presenting a dysregulated immune response and derangement of the epidermal barrier lipids. The Th2-type cytokines interleukin IL-4 and IL-13 play a prominent role in AD by activating the Janus Kinase/Signal Transduction and Activator of Transcription (JAK/STAT) intracellular signal axis. This study aimed to investigate the role of JAK/STAT in the lipid perturbations induced by Th2 signaling in 3D-epidermal equivalents. We used tofacitinib, a low-molecular-mass JAK inhibitor, to screen for the JAK/STAT-mediated deregulation of lipid metabolism. Th2 cytokines decreased the expression of elongases 1, 3, and 4, and serine-palmitoyl-transferase and increased that of sphingolipid delta(4)-desaturase, and carbonic anhydrase 2. Th2 cytokines inhibited the synthesis of palmitate and caused a depletion of triglycerides. This depletion was associated with altered PC profiles and fatty acid (FA) metabolism. Overall, the ceramide profiles were minimally affected. Except for most sphingolipids and very long chain FAs, the effects of Th2 on lipid pathways were reversed by co-treatment with tofacitinib. An increase in the mRNA levels of CPT1A and ACAT1, reduced by tofacitinib, suggests that Th2 cytokines promote FA beta-oxidation. In conclusion, pharmacological inhibition of JAK/STAT activation prevents the lipid disruption caused by halted homeostasis of FA metabolism.

We study the validity of quantum Fisher information (QFI) as a faithful quantum coherence and correlation quantier by drawing a comparison with subsystem's coherence measure, rst-order coherence (FOC) and the entanglement measure, Negativity to study the behavior of thermal quantum coherence and correlations in two qubit Heisenberg XXX model, placed in independently controllable magnetic eld by systematically varying the coupling parameter, magnetic eld and bath temperature for ferromagnetic and antiferromagnetic case. After carefully observing the prole of quantum coherence and correlation measures, we propose an inequality relations which shows that there may exist a quantitative relationship between QFI, Negativity and FOC in which, the equality exists at zero temperature. We identify QFI to be a more useful coherence quantier, as it quanties coherence of individual subsystems and correlations among the subsystems. On the other hand, FOC identies coherence present in the individual subsystems only. A reciprocal relationship between Negativity and FOC is also observed in dierent cases. We also observe the existence of entanglement in ferromagnetic case, in contrast to simple Heisenberg XXX model in uniform magnetic eld. We show that in the ferromagnetic case, a very small inhomogeneity in magnetic eld is capable of producing large values of thermal entanglement. This shows that the behavior of entanglement in the ferromagnetic Heisenberg system is highly unstable against inhomogeneity of magnetic elds, which is inevitably present in any solid state realization of qubits.

Wireless Sensor Networks are critical for modern applications ranging from environmental monitoring to smart city infrastructures. This research proposes a novel optimization learning and deployment strategy for Wireless Sensor Networks (WSNs) by 3D WUSN model is uniformly distributed M sensor nodes across diverse terrains, with clusters representing 20% of sensors, showcasing its ability to balance power consumption and extend network longevity, grounded in fuzzy clustering based protocol using the Fuzzy C-Means (FCM) method, called FCM-3DWUSN. Comparative analysis against established models including LEACH-C, K-Means and LEACH emphasized FCM-3DWUSN's outperformed performance, with average power consumption such as 134.990, 341.790, 143.895, and 192.984; respectively. The experimental result shows that FCM protocol in the 3D WUSN model can reduce energy consumption and improve the network lifetime to gather data and send the information.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

Three-dimensional (3D) geological modeling technology offers intricate geological information services and technical support for the research of urban geological conditions and their evolutionary mechanisms. It further facilitates the analysis of environmental geological problems, encompassing their distinguishing features and genetic mechanisms. The precision of such three-dimensional models is predominantly influenced by the caliber of modeling data, the chosen modeling methodologies, and the intricacy of the modeled geological objects. This research, exemplified by the three-dimensional geological structure modeling of the Wuhan metropolitan development area, aims to explore a comprehensive three-dimensional modeling framework for urban geology, particularly in scenarios with large-scale and complex geological conditions. This study holds significant technical value in enhancing the application of 3D geological modeling, as well as practical importance for urban geological investigations and research.

We investigate the behavior of thermal quantum coherence in the Heisenberg XXX model for a two-qubit system placed in independently controllable Inhomogeneous magnetic fields applied to two qubits respectively. We discuss the behavior of quantum coherence by systematically varying the coupling parameter, magnetic field, and temperature for both ferromagnetic and antiferromagnetic cases. The results show the interesting behavior of quantum coherence in a certain range of parameters. Generally, it is observed that quantum correlations decay with temperature, but in the ferromagnetic case with uniform magnetic interaction, it rises with temperature up to a certain threshold value and ultimately it decreases its value to zero. Moreover, it is observed that preserving the quantum coherence for small temperatures is very hard with the increasing magnetic field because, at small temperatures, quantum coherence decays sharply with the increase in magnetic field whereas at larger temperatures it decays completely at fairly large values of the magnetic field. The variation of quantum coherence with uniform magnetic field in the antiferromagnetic case is observed to be Gaussian for larger temperature but at zero or nearly zero temperature, it behaves as a constant function for uniform magnetic field up to a threshold value and then decays to zero with an infinite slope. This shows the signature of quantum phase transition from quantum nature to classicality.

A forecasting scheme of the thermal updraft velocity based on a theoretical model and data collected from flights records at gliding competitions, is presented. The forecasting scheme was based on the hypothesis that there is linear relationship between the overheat function at ground surface and the temperature difference between soil and air. The proportionality factor of this relationship was determined experimentally using observations recorded during gliding flights. The results showed that based on this simple scheme forecasting thermal convection is possible at any geographical location.

This paper proposes a novel method for optimizing the Cauer-type thermal network model considering both the temperature influence on the extraction of parameters and the errors caused by the physical structure. In terms of prediction of the transient junction temperature and the steady-state junction temperature, the parameters of conventional Cauer-type are modified, and the general method for estimating junction temperature is studied by using the adaptive thermal network model. The results show that junction temperature estimated by adaptive Cauer-type thermal network model is more accurate than that of the conventional model.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

This manuscript presents a system that can generate a 2D grid map and a 3D voxel model of an environment by fusing multiple sensors integrated into a robot. The fusion of these sensors is done by utilizing Robot Operating System (ROS) and some of its libraries. The sensors that are fused in the robot are a Light Detection and Ranging (LIDAR), Inertial Measurement Units (IMU), wheel encoders, and a Time-of-Flight camera. With the fusion of the point cloud data information obtained with the Time-of-Flight camera, the laser information of the LIDAR sensor, in addition to the odometry generated with the other sensors, a 2D grid map and a 3D model of two different environments were created, thus testing the performance of the system.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

The movement of liquid droplets on the energy gradient surface has attracted extensive attention. Inspired by biological features in nature, such as the periodic spindle-shaped nodes in spider silks and conical-like barbs of cacti, the structure-property-function relationship of multifunctional gradient surfaces. In this study, a series of specific patterns are fabricated by 3D printing technology, followed by modification via the atmospheric pressure plasma treatment and liquid phase chemical deposition, resulting in enhancing the ability of water droplets of 5μL to travel 18.47mm on a horizontal plane and 22.75mm against gravity up to 20° tilting angle. Additionally, analysis techniques have been employed including contact angle analyzer, ESCA and laser confocal microscope to evaluate the sample performance. This work could further be applied to many applications related to microfluidic devices, drug delivery and water/fog collection.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Ledge formation presents a significant challenge in endodontic treatment. Yet, there is still a lack of educational tooth models for hands-on practice. This study aimed to create and evaluate a tooth model for ledge management practice. A natural tooth with curved roots was collected for scientific use under ethics committee approval. Following initial root canal preparation, the tooth was scanned using micro-computed tomography (μCT) and 3D reconstructed. A K-file, created via computer-aided design (CAD), was partly inserted into the root canal wall of the 3D-reconstructed tooth. By subtracting the K-file from the tooth, a tooth model with a root canal ledge was produced. The models were then 3D printed for a hands-on workshop. A seven-item Likert scale questionnaire was administered to 20 postgraduate students and 10 endodontists to assess the model's quality and training effectiveness. The feedback from both students and experts was positive, with no statistically significant differences found between the two groups (p > 0.05). This novel tooth model is expected to address the existing gap in endodontic education and provide benefits for dental practitioners in future applications.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

The paper deals with an electrothermal model of a thermoelectric converter dedicated to performing simulations of coupled thermal and electrical phenomena taking place in harvesting processes. The proposed model is used to estimate the electrical energy gain from waste heat that would be sufficient to supply electronic circuits, in particular autonomous battery-less nodes of wireless sensor networks (WSN) and Internet of Things (IoT) devices. The developed model is not limited to low power electronic solutions such as WSN or IoT; it can also be scaled up and applied to simulations of considerably higher thermal power conversion. In the paper, a few practical case studies are presented that show the feasibility and suitability of the proposed model for complex simultaneous simulation processes, in both electrical and thermal domains. The first example deals with a combined simulation of the electrothermal model of a thermoelectric generator (TEG) and an electronic harvester circuit based on Analog Devices’ power management integrated circuit LTC3108. The second example relates to the thermalization effect in heat sink-less harvesting applications that could be mitigated by a pulse mode operation.

The aim of this research is to investigate the influence of model height employed in the deep drawing of orthodontic aligner sheets on force transmission and aligner thickness. Forty sheets (Zendura FLX) were thermoformed over four models of varying heights (15, 20, 25, and 30 mm). Normal contact force generated on the facial surface of the upper right central incisor (Tooth 11) was measured using pressure-sensitive films. Aligner thickness around Tooth 11 was measured at five points. A digital caliper and a micro-computed tomography (µ-CT) were employed for thickness measurements. The normal contact force exhibited an uneven distribution across the facial surface of Tooth 11. Model 15 displayed the highest force (88.9±23.2 N), while Model 30 exhibited the lowest (45.7±15.8 N). The force distribution was more favorable for bodily movement with Model 15. Thickness measurements, conducted using a digital caliper and µ-CT, revealed substantial thinning of the aligner after thermoforming. This thinning was most pronounced at the incisal edge (50% of the original thickness) and least at the gingivo-facial part (85%). Additionally, there was a progressive reduction in aligner thickness with increasing model height, which was most significant on the facial tooth surfaces. We conclude that the thermoplastic aligner sheets undergo substantial thinning during the thermoforming process, which becomes more pronounced as the height of the model increases. As a result, there is a decrease in both overall and localized force transmission, which could lead to increased tipping by the aligner and a diminished ability to achieve bodily movement.

Aquifer karstic structures, due to their complex nature, present significant challenges in accurately mapping their intricate features. Traditional methods often rely on invasive techniques or sophisticated equipment, limiting accessibility and feasibility. In this paper, we propose a new approach to non-invasive, low-cost 3D reconstruction using a camera that observes the light projection of a simple diving lamp. Our method capitalizes on the principles of structured light, leveraging the projection of light contours onto the karstic surfaces. By capturing the resultant light patterns with a camera, we reconstruct three-dimensional representations of the structures. The simplicity and portability of the equipment required make this method highly versatile, enabling deployment in diverse underwater environments. We validate our approach through extensive field experiments conducted in various aquifer karstic settings. The results demonstrate the efficacy of our method in accurately delineating intricate karstic features with remarkable detail and resolution. Furthermore, the non-destructive nature of this technique minimizes disturbance to delicate aquatic ecosystems while providing valuable insights into the subterranean landscape. This innovative methodology not only offers a cost-effective and non-invasive means of mapping aquifer karstic structures but also opens avenues for comprehensive environmental monitoring and resource management. Its potential applications span hydrogeological studies, environmental conservation efforts, and sustainable water resource management in karstic terrains worldwide.

Lithium-ion batteries serve as the primary sources of power for electric vehicles (EVs) and hybrid electric vehicles (HEVs). For vehicle applications, battery management systems (BMSs) are nec-essary to protect lithium-ion batteries from overheating and to ensure optimum vehicle perfor-mance. Our approach to developing a BMS was based on recent advances in the application of phase field models for lithium-ion batteries. In particular, our reduced-order model (ROM) uti-lized a dataset generated from the COMSOL® Multiphysics simulation of the Cahn–Hilliard equation for a single particle of a lithium iron phosphate (LiFePO4) cathode: an example of using a reduced-order model (ROM) based on a single-particle model (SPM). The main innovation of our ROM is that the SPM is fully coupled to a heat transfer model at the battery cell level. We utilized principal component analysis to identify a lower-order model that could reproduce the battery’s voltage and temperature response for ambient temperatures ranging from 253 to 298 K and for discharge rates ranging from 1 C to 20.5 C. The reduced-order dataset was then fitted to the ex-perimental data for an A123 Systems 26650 2.3 Ah cylindrical battery using deep neural network (DNN) regression.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

Amidst the escalating demands for efficient Intelligent Transportation Systems (ITS) management, the significance of accurate Origin-Destination (OD) data prediction has emerged as a paramount concern, given its indispensable role in the ITS domain. This paper introduces a groundbreaking integrated model, creatively fusing the unique strengths of Graph Convolutional Network (GCN), Residual Neural Network (ResNet), and Long Short-Term Memory Network (LSTM) into a single architecture, which we name GraphResLSTM, to exploit road segment average speed data for OD prediction. Compared with conventional road segment traffic volume data, average speed data is more readily available, significantly reducing the data accessibility barrier for OD prediction. We underscore the critical role of selection of key road segments and employs a combination of Entropy Weight Method and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) to identify 41 representative road segments from the experimental road network. In the experimental phase, we simulate 86400000 seconds of traffic conditions, generating a total of 1440000 data records. Utilizing these simulated data, we design and conduct comparative experiments between models as well as data types. The results demonstrate that both the GraphResLSTM model and road segment average speed data outperform other models and data types notably in OD prediction tasks.

Fused deposition modeling (FDM) is widely applied in various fields due to its affordability and ease of use. However, it faces challenges such as achieving high surface quality, precise dimensional tolerance and overcoming anisotropic mechanical properties. This paper analyzes and compare the machinability of 3D printed PLA, PETG and carbon fiber reinforced PETG focusing on surface roughness and burr formation. A design of experiments (DoE) with a full factorial design was used, considering three factors: rotation speed, feed rate and depth of cut. Each factor had different levels: rotational speed at 3000, 5500 and 8000 rpm; feed rate at 400, 600 and 800 mm/min; and depth of cut at 0.2, 0.4, 0.6, and 0.8 mm. Machinability was evaluated by roughness and burr height using a profilometer for all the materials under the same milling conditions. To evaluate the statistical significance of the influence of various processing parameters on surface roughness and burr formation in 3D printed components made of three different materials PLA, PETG and carbon fiber reinforced PETG, an analysis of variance (ANOVA) test was conducted. This analysis investigated whether variations in rotational speed, feed rate and depth of cut resulted in measurable and significant differences in machinability results. Results showed that milling parameters significantly affect roughness and burr formation, with optimal conditions for minimizing any misalignment highlighting the trade-offs in parameter selection. These results provide insights into the post-processing of FDM-printed materials with milling, indicating the need for a balanced approach to parameter selection based on application-specific requirements.

The present study drops the line for the flow characteristics of fly ash-based (FA) geopolymers reinforced with polypropylene (PP) fibers undergoing the extrusion process during three-dimensional printing. Applying to the Herschel-Bulkley rheological model the research is ready with the sound theoretical basis which is used to understand the flow behavior of these materials under various conditions. A combination of experimental and numerical techniques that are based on the Finite Element Method (FEM) in COMSOL has been used in this study. The results of both the experimental and simulation approaches are then compared and the behavior of the material during extrusion is then examined. The experimental results proved PP fiber content has significant effects on rheological properties. The experiments on mixes which are either devoid of fibers or possess a high content of fiber, encountered problems like a high static yield stress and material segregation. Mixes with fibers of moderate content showed smoother extrusion processes, which means that a suitable range of fiber addition exists for the fibers that optimally balance the mechanical properties and extrudability. Numerical simulations typically agreed with experimental data for fiber contents up until it reached a certain level but not above, suggesting the existence of more complex interactions inside the fibers and the necessity for the subsequent model refinements. The investigation outlines a 0.25% and 0.5% fiber content range that leads to enhanced performance without bringing the extrusion process to greater complications and further making the production of proper, architecturally printed structures possible.

Background: Metabolic flux analysis (MFA) is an indispensable tool in metabolic engineering. The simplest variant of MFA relies on an overdetermined stoichiometric model of the cell’s metabolism under the pseudo-steady state assumption, to evaluate the intracellular flux distribution. Despite its long history, the issue of model error in the overdetermined MFA, particularly misspecifications of the stoichiometric matrix, has not received much attention. Method: We evaluated the performance of statistical tests from linear least square regressions, namely Ramsey RESET test, F-test and Lagrange multiplier test, in detecting model misspecifications in the overdetermined MFA, particularly missing reactions. We further proposed an iterative procedure using the F-test to correct such an issue. Result: Using Chinese hamster ovary and random metabolic networks, we demonstrated that: (1) a statistically significant regression does not guarantee high accuracy of the flux estimates, (2) the removal of a reaction with a low flux magnitude can cause disproportionately large biases in the flux estimates, (3) the F-test could efficiently detect missing reactions, and (4) the proposed iterative procedure could robustly resolve the omission of reactions. Conclusion: Our work demonstrated that statistical analysis and tests could be used to systematically assess, detect and resolve model misspecifications in the overdetermined MFA.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

Pulmonary Embolism (PE) is the obstruction of blood arteries in the lungs by a blood clot. The mortality risk for PE is approximately 30%. Detecting pulmonary embolism in the segmental arteries of the lung is more challenging than in the main arteries and is very prone to being missed. A computer-based approach was created in this work to automatically identify pulmonary embolism in the segmental arteries using computed tomography images. The system's infrastructure includes an enhanced Mask R-CNN deep neural network that has been trained with images containing PE. The network accurately identifies the location of the pulmonary embolism on the computed tomography picture and successfully extracts its borders. The investigation was conducted by generating a local dataset. The study's performance was evaluated using pulmonary embolisms identified manually by the expert radiologist. The sensitivity, specificity, accuracy, dice coefficient, and Jaccard index values for 2130 pictures were 96.4%, 93.5%, 96.1%, 0.96, and 0.90, respectively. The improved Mask R-CNN model has demonstrated superior performance when compared to the traditional Mask R-CNN and U-Net models. This high-performance technology is designed to identify pulmonary embolism and will aid professionals in assessing the size of the embolism.

Augmented Reality (AR) and 3D printing (3DP) are novel technologies in the orthopedic field. Over the past decade, enthusiasm for these new digital applications is driving new perspectives in improving diagnostic accuracy and sensitivity in the field of traumatology. Currently, however, it is still difficult to quantify the value and impact in the medical-scientific field especially in the improvement of diagnostic in complex fractures. Acetabulum fractures have always been a challenge among orthopedics, for volumetric complexity and low diagnostic reliability.Background/Objectives: The goal of this study is to determine whether these methods can improve the learning aspect and diagnostic accuracy of complex acetabulum fractures compared to gold standard CT (computed tomography). Methods: Orthopedic residents of our department have been selected and divided into Junior (JUN) and Senior (SEN) groups. Associated fractures of acetabulum have been included in the study, obtaining : CT-scans, 3DP model, and AR model displayed on a tablet screen. In a double-blind questionnaire, each resident classified every fracture according to methods. Diagnostic accuracy (DA), response time (RT), agreement (R), and confidence (C) were measured. Results: 20 residents (JUN=10, SEN=10) classified five fractures. Overall DAs were 26% (CT), 18% (3DP), and 29% (AR). AR-DA resulted to be superior to 3DP-DA (p=0,04). DA means (JUN vs SEN respectively) were :CT-DA was 20% vs 32% (p<0.05), 3DP-DA was 12% vs 24% (p=0.08), and AR-DA was 28% vs 30% (p=0,80). Overall RT was 61.2 sec (±24,6) for CT, 35.8 sec (±20,1) for 3DP, and 46,7 sec (±20,8) for AR. R was fairly poor between methods and groups. 3DPs resulted to have superior overall C (65%). Conclusions: AR resulted to have the same Overall DA as CT, independent from experience, 3DP has minor DA and R, but it resulted to be the most confident and fast method. Intra and interobserver R between methods remain very poor in residents.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

This paper aims to demonstrate how the detection of communities for epidemiological networks can be used to reduce the dimensionality of optimal control problems. A range of planted partition stochastic blockmodels are generated, where the underlying communities in the model vary in detectability. A high-performance computing workflow is then used to simulate and estimate reduced model dynamics for the networks, which in turn is used to find optimal control solutions.

Public safety and intelligent surveillance systems critically depend on anomaly behavior detection for effective monitoring. In real-world pedestrian detection scenarios, prevalent challenges such as missed detections, complex background interference, and small target sizes hinder accurate anomaly identification. To address these issues, this study introduces YOLO-ABD, a lightweight method for anomaly behavior detection that integrates small target detection and channel shuffling. This method employs YOLOv8n as the baseline model, incorporating a small target detection mechanism in the Head part and utilizing GSConv convolution in the Backbone to enhance perceptual capability. Additionally, the SimAM attention mechanism is integrated to mitigate complex background interference, thereby improving target detection performance. Evaluation on the IITB-Corridor dataset demonstrated mAP50 and mAP50-95 scores of 89.3% and 60.6%, respectively. Generalization testing on the street-view-gdogo dataset further highlighted the superiority of YOLO-ABD over advanced detection algorithms, underscoring its effectiveness and generalizability. With a relatively small parameter count, YOLO-ABD presents an excellent lightweight solution for pedestrian anomaly behavior detection.