Treatment of the non-purified mixture of dinitro isomers obtained from the nitration of 1,4-dimethoxybenzene with piperidine, led to the isolation of novel but minor adduct, 1-(2,5-dimethoxy-4-nitrophenyl)piperidine (2b) in 15% yield. Yields of nucleophilic aromatic substitution adducts are high when using purified 1,4-dimethoxy-2,5-dinitrobenzene (1b) with piperidine and pyrrolidine to give 2b and 1-(2,5-dimethoxy-4-nitrophenyl)pyrrolidine (3b) in 76% and 82%, respectively.

Biomaterials are the basis for the development of medicine because they allow safe contact with a living organism. The aim of this work was to produce innovative oxide layers with a porous microstructure on the surface of commercially pure titanium Grade 4 (CpTi G4), and to characterize their properties as drug carriers. Anodization of the CpTi G4 subjected to mechanical grinding and electrochemical polishing was carried out in a solution of 1M ethylene glycol with the addition of 40 g of ammonium fluoride at a voltage of 20 V for 2, 18, 24 and 48 hours at room temperature. It was found that the longer anodization time, the greater the number of pores formed on the CpTi G4 surface as revealed by FE-SEM method, and the greater the surface roughness determined in profilometric tests. As the anodizing time increases, the amount of the drug in the form of gentamicin sulfate incorporated into the resulting pores decreases. The most favorable drug release kinetics profile determined by UV-VIS absorption spectroscopy was found for the CpTi G4 anodized for 2 h making them the best choice when it comes to the drug carrier allowing full use of the therapeutic dose of the drug.

Background: Ventilator-associated pneumonia (VAP) is among the most common healthcare-associated infections in Pediatric Intensive Care Units (PICUs). Because of the lack of a gold-standard diagnostic test, early diagnosis of VAP is challenging. We investigated whether bronchial biomarkers interleukin-4 (IL-4), plasminogen activator inhibitor-1 (PAI-1) and soluble receptor for advanced glycation end products (RAGE) could contribute in early VAP diagnosis through their fluctuation in time in critically ill pediatric patients. Methods: Bronchial secretions were collected from PICU patients with VAP on days 1 and 6. PAI-1, RAGE and IL-4 levels were measured by ELISA. Protein concentrations between high and low VAP suspicion patients were compared using unpaired Student’s t or Mann–Whitney U tests. Results: Twenty PICU patients, with median age 7.75yrs (range 0.5-15.3), mechanically ventilated for ≥48hrs with increased oxygenation requirements and VAP clinical/laboratory signs were enrolled. They were divided in VAP high-suspicion (n=12) or low-suspicion (n=8) groups based on Clinical Pulmonary Infection Score (cutoff:6). ΡΑΙ-1 και RAGE levels did not differ between high- or low-VAP suspicion groups the 1st or 6th days (p-value>0.05). IL-4 was not detected in bronchial secretions. Conclusion: Bronchial concentrations of IL-4, PAI-1 and RAGE in critically ill children are not correlated with high- or low-VAP suspicion.

The reaction of 2-bromo-1-(5-methyl-1-(4-nitrophenyl)-1H-1,2,3-triazol-4-yl)ethan-1-one (1) with 4-amino-5-((2,4-dichlorophenoxy)methyl)-4H-1,2,4-triazole-3-thiol (2) in absolute ethanol in the presence of triethyl amine as catalyst gave 2-((4-amino-5-((2,4-dichlorophenoxy)methyl)-4H-1,2,4-triazol-3-yl)thio)-1-(5-methyl-1-(4-nitrophenyl)-1H-1,2,3-triazol-4-yl)ethan-1-one (3) in 73% yield. The structure of the title heterocycle (3) was confirmed by X-ray single crystal diffraction and spectral analyses (NMR and IR).

Novel 4-(diphenylphosphoryl)-1-phenylbutane-1,3-dione was synthesized by the reaction of diketone enamine with diphenylchloro phosphine followed by oxidation and hydrolysis of the enamine phosphine formed. Tautomeric transformation of the diketone moiety of phosphine oxide was investigated by ¹H NMR. Three out of five possible tautomers were observed in the 4-(diphenylphosphoryl)-1-phenylbutane-1,3-dione solution. The major tautomer was the form with a diketone fragment.

Zwitterionic polymers emerge as very useful materials for applications in antifouling surfaces. The properties of these polymers can be tuned by variation of the chemical structure of the corresponding monomer. In this study, two zwitterionic ammonium sulfonate monomers bearing an hydroxyl function and a styrenic polymerizable groups were prepared in two steps. The two monomers were obtained using 4-vinylbenzyl chloride as the key precursor. The zwitterionic monomers were characterized by 1H NMR, 13C NMR, IR spectroscopy and high-resolution mass spectrometry (HRMS). These two monomers enable the preparation of novel zwitterionic polymers with enhanced hydrophilicity due to the presence of a hydroxyl group.

(S)-1-Methyl-2-oxoimidazolidine-4-carboxylic acid 1 is an analog of (S)-pyroglutamic acid, a key component of naturally occurring peptide hormones and synthetic pharmaceutical candidates. Reaction of (S)-2-amino-3-(methylamino)propionic acid with COCl2 and aqueous NaHCO3 followed by ion exchange afforded 1, which was recrystallized from acetonitrile and then characterized by IR, 1H NMR, 13C NMR, polarimetry, elemental microanalysis, high resolution mass spectrometry and single crystal X-ray diffraction. The acid 1 crystallized in the orthorhombic chiral space group P212121 with cell constants a = 6.2275(4) Å, b = 8.3963(5) Å, c = 24.9490(14) Å. The X-ray crystal structure reveals that two distinct conformers of 1 occur at alternating positions within helices which are supported by hydrogen-bonding. Each molecule of 1 is linked to its two neighbors in the helix by a total of three hydrogen bonds and four molecules of 1 are contained within each turn of the helix. The pattern of hydrogen bonds illustrates a preference for the carboxylic acid group to act as a hydrogen bond donor and for the urea unit to be a hydrogen bond acceptor.

With the aim to produce new heterocycle molecules, the previously reported 2-(aminomethyl)-2-(4-chlorophenyl)-2,3-dihydroquinazolin-4(1H)-one was converted efficiently by reacting with N,N’-dithiocarbonyldiimidazole (DTCI), to produce the substituted imidazolidine-2-thione moiety inserted in a three fused ring scaffold of the title compound. The molecular composition was confirmed by a high-resolution MS experiment, and its structure was elucidated by 1H, 13CNMR, and IR analyses. The thioacetamide form of the product was supported by density functional theory (DFT)-NMR analysis where 13C chemical shifts of thioacetamide form and of its iminothiol tautomer were calculated in chloroform at the BP86 /Jgauss-TZP2 level of theory. The very good linear correlation between 13C chemical shifts by experiment and by calculation for the NHC=S form confirmed the structure.

Six-Transmembrane Epithelial Antigen of the Prostate 1-4 (STEAP1-4) compose a family of metalloproteinases involved in iron and copper homeostasis and other cellular processes. Thus far, five homologs are known: STEAP1, STEAP1B, STEAP2, STEAP3, and STEAP4. In prostate cancer, STEAP1, STEAP2, and STEAP4 are overexpressed while STEAP3 expression is downregulated. Although the metalloreductase activities of STEAP1-4 are well-documented, their other biological functions are not. Furthermore, the properties and expression levels of STEAP heterotrimers, homotrimers, heterodimers, and homodimers are not well-understood. Nevertheless, studies over the last few decades have provided sufficient impetus to investigate STEAP1-4 as potential biomarkers and therapeutic targets for prostate cancer. In particular, STEAP1 is the target of many emerging immunotherapies. Herein, we give an overview of the structure, physiology, and pathophysiology of STEAP1-4 to provide context for past and current efforts to translate STEAP1-4 into the clinic.

1-[5-(4-methylphenyl)-1,3,4-oxadiazol-2-yl]methanamine compound has been successfully synthesized by reacting p-Toluic hydrazide and glycine via polyphosphoric acid condensation route. The course of the reaction was found to be high yielding and the title compound was spectroscopically characterized by FT-IR, DSC, 13C/1H-NMR and Mass spectrometric techniques.

Vilsmeier–Haack reaction of (E)-1-(1-(3,5-difluorophenyl)ethylidene)-2-phenylhydrazine (1) using dimethyl formamide in excess of phosphorous oxychloride by conventional method, resulted in the synthesis of title compound 3-(3,5-difluorophenyl)-1-phenyl-1H-pyrazole-4- carbaldehyde (2) in good yield and high purity. Structure characterization of the novel title compound was done by IR, ¹H NMR, ¹³C NMR and mass spectral analysis.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

.Bacground: Sepsis remains a major health challenge worldwide, characterized by a dysre-gulated host response to infection, leading to high mortality and morbidity in intensive care units (ICUs). The Fibrosis 4 (FIB-4) index, originally developed to assess liver fibrosis in hepatitis C patients, has recently been explored for its potential prognostic value in sepsis patients. Method: This study retrospectively analyzed 309 sepsis patients admitted to the Internal Me-dicine and Anaesthesia ICUs between December 12, 2021, and December 15, 2023, to inves-tigate the relationship between FIB-4 levels, Acute Physiology and Chronic Health Evaluation (APACHE), and Sequential Organ Failure Assessment (SOFA) and clinical outcomes. Results: The study found that higher FIB-4 measurements were statistically significantly asso-ciated with increased 28-day mortality, with a cut-off value of 4.9 providing a sensitivity of 54.92% and specificity of 74.25%. Logistic regression analysis indicated that elevated Conclusion:FIB-4 levels were a significant predictor of early mortality, suggesting that the FIB-4 index could serve as a valuable prognostic tool in assessing the severity and prognosis of sepsis patients.

The crystals, C11H4BrF5N2S, (I), 1-((4-bromothiophen-2-yl)methylene)-2-(perfluorophenyl)hydrazine and C12H6BrF5N2S, (II), 1-((4-bromo-5-methylthiophen-2-yl)methylene)-2-(perfluorophenyl)hydrazine are molecules with two rings and hydrazone part like a centre of the molecule. The compounds have been synthesized and characterized by elemental, spectroscopic (¹H-NMR) analysis. The crystal structures of the solid phase were determined by single crystal X-ray diffraction method. They crystallize in the monoclinic space group with Z = 4 and Z = 2 molecules per unit-cell. The compound (I) crystallizes as a racemate in the centrosymmetric space group and the compound (II) crystallizes as a non-racemate in the non-centrosymmetric space group. The “absolute configuration and conformation for bond values” were derived from the anomalous dispersion (ad) for (II). The crystal structures are revealed diverse non-covalent interactions such as intra- and interhydrogen bonding, π-ring···π-ring, C-H···π-ring and they were investigated. The expected stereochemistry of hydrazones atoms C7, N2 and N1 were confirmed for (I) and (II). The hole molecule of the (I), and (II) possesses “a boat conformation” like a 6-membered ring. The results of the single crystal studies are reproduced with the help of Hirshfeld surface study and Gaussian software.

Naphtho[1,8-de][1,2]oxazin-4-ol and its acyl or benzyl derivatives ring open to various 2,8-dihydroxy-1-naphthonitriles, that undergo methylation, reduction, demethylation and debenzylation reactions, to afford the target compound (E)-2-hydroxy-8-methoxy-1-naphthaldehyde. The best overall yield of the latter was 28.7%. This compound was converted to its corresponding (E)-2-hydroxy-8-methoxy-1-naphthaldehyde ox-ime, which was oxidatively o-cyclized with phenyliodine(III) diacetate (PIDA) to 9-methoxynaphtho[1,2-d]isoxazole 2-oxide. The latter in deuterated DMSO, at room temperature, rearranged to its isomer to 2-hydroxy-8-methoxy(naphthalen-1-yl)nitrile oxide. The isomeriza-tion was detected by a time-course plot 1H NMR spectroscopy and further identified from its13C NMR and HRMS spectra. The nitrile oxide was stable in (non)deuterated DMSO for at least 18 hours. A 3,4-bis(2-hydroxy-8-methoxynaphthalen-1-yl)-1,2,5-oxadiazole 2-oxide as a dimeriza-tion product or an isocyanate as a rearrangement isomer were both ruled out, the former by the absence of the relevant molecular ion in its HRMS spectrum while the latter by 1,3-dipolar cy-cloaddition reactions with various dipolarophiles that gave substituted isoxazoles, thus con-firming the nitrile oxide structure.

Introduction: The association of gene variants for interleukin 6(IL-6) (rs1800796), interleukin 10 (IL-10) (rs1800896) and tumor necrosis factorα (TNFα (rs1800629) with the occurrence of spontaneous preterm birth (PTB) was investigated to determine whether these genetic variants are a risk factor. Materials and methods: 199 blood samples from pregnant women who had given birth prematurely and 200 control blood samples were analyzed to determine single nucleotide polymor-phisms (SNPs) of genes for IL-6 (rs1800796), IL-10 (rs1800896) and TNFα (rs1800629). The control samples were samples from pregnant women with term delivery. Isolation of DNA was per-formed on mini-spin columns according to the manufacturer's protocol. The quality and purity of the isolated DNA were tested using a Qubit 3 fluorometer. Genotyping was performed with an ABI PRISM 7500 SDS using TaqMan SNP genotyping assays. The genotypes obtained were an-alyzed using the 7500 Software v2.3 package. Results: Carriers of the A/A genotype for the rs1800629 of the TNFα gene have 4.81 times greater chance of late-onset PTB compared to carriers of the G/G and A/G genotypes in the recessive inheritance model. The presence of the G/G genotype in the recessive inheritance model compared with the G/A and A/A genotypes for the rs1800896 of the IL-10 gene represents a potentially protective factor, with mothers in the term-birth group having an almost 2-fold lower odds of PTB in general and an almost 10-fold lower odds of early PTB. On the other hand, carriers of the A/G genotype of rs1800896 have a 1.54-fold higher chance of preterm birth in general and a 1.6-fold higher chance of late preterm birth in the super dominant inheritance model compared to the A/A and G/G genotypes in the group of mothers with PTB. In this study, no association was found between PTB and rs1800796 of the IL-6 gene. Conclusion: rs1800629 in mothers was associated with PTB. rs1800896 shows a potentially protective effect for the occurrence of PTB in this study. No association was found between PTB and rs1800796.

In this paper, we extend the KdVSKR equations in (1+1)-dimension and (2+1)-dimension to fractional KdVSKR equations with modified Riemann-Liouville derivative. The (2+1)-dimensional KdVSKR equation, which is a recent extension of (1+1)-dimensional KdVSKR equation, can model the resonances of solitons in shallow water. By means of the Hirota bilinear method, finite symmetry group method and consistent Riccati expansion method, many new interaction solutions have been derived. Soliton-cnoidal interaction solution of the (1+1)-dimensional fractional KdVSKR equation has been derived for the first time. For the (2+1)-dimensional frac-tional KdVSKR equation, two-wave interaction solutions and three-wave interaction solutions, including dark-soliton-sine interaction solution, bright-soliton-elliptic interaction solution, and lump-hyperbolic-sine interaction solution, have been derived. Impact of the fractional order on the shapes of these solutions has been illustrated by figures. Three-wave interaction solutions of fractional systems have not been reported in the existing references. The research idea in this paper can be applied to other fractional differential equations.

Exoskeleton technology has been shown to be useful for individuals with spinal cord injury (SCI), potentially facilitating their recovery of motor function and social reintegration. However, studies on the safety and usability of exoskeletons are limited. This study aimed to design a powered exoskeleton for SCI and evaluate its safety and usability. Ten healthy adults participated in this study. The prototype exoskeleton featured an adjustable frame, computer-controlled hip and knee joint actuators, and a gait-trigger sensor. The experimental actions included walking, standing, and sitting, with and without the prototype. Safety outcomes included adverse events, vital signs, numerical rating scale (NRS) scores for pain, discomfort, and fatigue, and prototype-human body clearance. Usability outcomes included donning and doffing times, subjective ratings, gait speed, stride length, and kinematic parameters of hip and knee joint angles. Safety outcomes showed no serious adverse events, stable vital signs, minimal NRS scores, and acceptable clearance. Usability outcomes showed high efficiency and received positive ratings. Kinematic parameters showed significant positive correlations between normal walking and walking with the prototype for both hip and knee joint angles, confirming its effectiveness in assisting walking. However, further device improvements and gait parameter tuning are necessary for future clinical application.

Dark pigmentation can be observed in various parts of the plant, ranging from foliage to petals to berries. The molecular basis of black pigmentation appears to vary among species, with anthocyanins playing a significant role, although specific anthocyanin types and their mechanisms differ. These findings suggest that the development of phenotypes is species-specific or varies between larger taxonomic groups; this is further supported by the polyphyletic nature of dark pigmentation. Additionally, several different regulatory mechanisms have been described for the occurrence of dark pigmentation. Firstly, the repression or knockout of the competing flavone biosynthesis has been shown to lead to darker pigmentation while another mechanism is based on the activation and upregulation of the anthocyanin biosynthesis genes in the presence of MYB transcription factors. Potential ecological functions of dark pigmentation were identified as the protection of the photosynthesis apparatus, camouflage against herbivores, and the attraction of pollinators. Promising industrial applications include microbial factories for the production of natural food colourants, induction of novel phenotypes for the ornamental plant industry and lastly the increase of anthocyanins within agriculturally relevant crops.

A Cu₂ZnSnS₄ (CZTS) film with a thickness of approximately 1.5 μm was fabricated on a Mo-coated glass substrate by annealing a CZTS precursor fabricated from nanoparticle ink. The chemical states of the elements in the CZTS thin film in the depth direction were studied to identify the presence of secondary phases, which are detrimental to the performance of solar cells containing CZTS. X-ray diffraction was unable to detect any secondary phases in CZTS because of their small relative amount. Instead, X-ray photoelectron spectroscopy (XPS), which is highly sensitive to chemical state, was conducted at different depths in the CZTS film to further check the presence of secondary phases. XPS analysis revealed peaks shift consistent with the presence of secondary phases. For the CZTS film annealed in a S atmosphere at 575 °C for 3 h, the film surface consisted of a secondary-phase layer composed of CuS, ZnS, and SnSx (x=1 or 2) originating from the decomposition of CZTS. At depths below 80 nm, the film was pure CZTS. Formation of MoS2 at the CZTS–Mo interface was confirmed by XPS analysis of Mo and S.

Despite decreasing anthropogenic mercury (Hg) emissions in Europe and the banning and restriction of many persistent organic pollutants (POPs) under the Stockholm Convention, Mediterranean marine mammals still have one of the highest body burdens of persistent pollutants in the world. Moreover, the Mediterranean basin is one of the most sensitive to climate change, with likely changes in the biogeochemical cycle and bioavailability of Hg, primary productivity, and the length and composition of pelagic food webs. The availability of food resources for marine mammals is also affected by widespread overfishing and the increasing number of alien species colonizing the basin. After reporting the most recent findings on the biogeochemical cycle of Hg in the Mediterranean Sea and the physico-chemical and bio-ecological factors determining its exceptional bioaccumulation in odontocetes, this review discusses possible future changes in the bioavailability of the metal. Recent ocean-atmosphere-land models predict that in mid-latitude seas, water warming (which in the Mediterranean is 20% faster than the global average) is likely to decrease the solubility of Hg and favor the escape of the metal to the atmosphere. However, the basin has been affected for thousands of years by natural and anthropogenic inputs of metals, and climate change with sea level rise (3.6 ± 0.3 mm year-1 in the last two decades) and the frequency of extreme weather events will likely remobilize large amount of legacy Hg from soils, riverine and coastal sediments. Moreover, possible changes in pelagic food webs and food availability could determine dietary shifts and lower growth rates in Mediterranean cetaceans, increasing their Hg body burden. Although adult marine mammals have evolved the ability to detoxify monomethylmercury (MMHg) and store the metal in the liver and other organs as insoluble Hg-Se crystals, in Mediterranean populations more exposed to the metal, this process can deplete the biological pool of Se, increasing their susceptibility to infectious diseases and autoimmune disorders. Mediterranean mammals are also among the most exposed in the world to legacy POPs, micro- and nanoplastics and contaminants of emerging interest. Concomitant exposure to these synthetic chemicals may pose a much more serious threat than the Se depletion. Unfortunately, as shown by literature data summarized in this review, the most exposed populations are those living in the NW basin, the main feeding and reproductive area for most Mediterranean cetaceans, declared a sanctuary for their protection since the 2002. Thus, while emphasizing the adoption of all available approaches to mitigate anthropogenic pressure with fishing and maritime traffic, it is recommended to direct future research efforts towards the assessment of possible biological effects, at individual and population level, of chronic and simultaneous exposure to Hg, legacy POPs, contaminants of emerging interest and microplastics.

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic and it represents a pollutant of global concern. Liquid Hg is highly volatile and it can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paints, plasters, roof tiles, concretes, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into 7 units) covers a surface of about 65 ha and contains mining structures and managers and workers buildings. In this work, nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in the units 2, 3 and 6. Moreover, detailed measurements were performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in terms of space and time mostly depending on the distance from the building hosting driers, furnaces and condensers and ambient temperature, respectively. In the Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng m⁻³, while in the Unit 6 they were on average much higher and occasionally they saturated the GEM measurement device (>50,000 ng m⁻³). Concentrations of total (in mg kg⁻¹) and leached (in μg L⁻¹) mercury measured in different building materials (up to 46,580 mg kg⁻¹ and 4,470 mg L⁻¹ for total and leached mercury, respectively) showed for the same type of material highly variable values in dependence on the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for the operational cleanings to be carried out during the reclamation activities.

Hydrogen sulfide is present in active or extinct volcanic areas (mofettas). The habitable premises in these areas are affected by the presence of hydrogen sulfide, which, even in low concentrations, gives off a bad to unbearable smell. If the living spaces considered are closed enclosures, then a system can be designed to reduce the concentration of hydrogen sulfide. This paper presents a membrane way to reduce the hydrogen sulfide concentration to acceptable limits using a cellulosic derivative-propylene hollow fiber based composite membrane module. The cellulosic derivatives considered were carboxymethyl–cellulose (NaCMC), cellulose acetate (CA), methyl 2–hydroxyethyl–cellulose (MHEC), and 2–hydroxyethyl–cellulose (HEC). In the permeation module, hydrogen sulfide is captured with a solution of cadmium that forms cadmium sulfide, usable as a luminescent substance. The composite membranes were characterized by SEM, EDAX, FTIR, FTIR 2D maps, thermal analysis (TG and DSC) and from the perspective of hydrogen sulfide air removal performance. To determine the process performances, the variables were: the nature of the cellulosic derivative–polypropylene hollow fiber composite membrane, the concentration of hydrogen sulfide in the polluted air, the flow rate of polluted air, and the pH of the cadmium nitrate solution. Pertraction efficiency was maximum for the sodium carboxymethyl–cellulose (NaCMC)-polypropylene hollow fiber membrane, a hydrogen sulfide concentration in the polluted air of 20 ppm, polluted air flow rate of 50 L/min, and a pH of 2 and 4.

The treatment of the bulky Rind-based dibromosilanes, (Rind)2SiBr2 (2) [Rind = 1,1,7,7-tetra-R1-3,3,5,5-tetra-R2-s-hydrindacen-4-yl: EMind (a: R1 = Et, R2 = Me) and Eind (b: R1 = R2 = Et)], with two equivalents of tBuLi in Et2O at low temperatures resulted in the formation of blue solutions derived from the diarylsilylenes, (Rind)2Si: (3). Upon warming the solutions above −20 °C, the blue color gradually faded, accompanying the decomposition of 3 and yielding the cyclic hydrosilanes (4) via intramolecular C−H bond insertion at the Si(II) center. The molecular structures of the bulky Eind-based 3b and 4b were confirmed by X-ray crystallography. Thus, at −20 °C, blue crystals were formed (Crystal-A), which were identified as mixed crystals of 3b and 4b. Additionally, colorless crystals of 4b as a singular component were isolated (Crystal-B), whose structure was also determined by an X-ray diffraction analysis. Although the isolation of 3 was difficult due to their thermally-labile nature, their structural characteristics and electronic properties were discussed based on the experimental findings complemented by computational results. We also examined the hydrolysis of 3b to afford the silanol, (Eind)2SiH(OH) (5b).

Alectinib hydrochloride is an anticancer medication used for the first-line treatment of non-small cell lung cancer. Although it has been approved for medical use ten years ago, and three polymorphs of this substance were proposed based on X-ray diffraction patterns, their crystal structures remained unknown to date. The main problem was preparation of high quality single crystals due to very low solubility of the salt. Herein we report on molecular and crystal structure of form I of alectinib hydrochloride as obtained by powder X-ray diffraction data from laboratory source. The refinement revealed that the nitrogen atom of the morpholinyl ring is protonated. The chloride anion interacts with the H(N) atoms of the morpholine and benzo[b]carbazole rings to form infinite H-bonded chains.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

Bananas, a staple food globally and a key agricultural commodity, face a severe threat from the fungus Fusarium oxysporum form specialis cubense (Foc), significantly impacting production. Genetic improvement to develop resistant cultivars stands out as a crucial strategy to mitigate this disease. This study focused on assessing and recommending enhanced diploid banana varieties for resistance against Foc subtropical race 4 (ST4) and Foc race 1 (R1). Twenty-five improved diploids developed by Embrapa, Brazil, underwent evaluation. Utilizing a scale for internal symptoms at 90 days post-inoculation, genotypes were categorized from highly resistant to highly susceptible based on the internal symptom index. The diploid M53 exhibited high resistance to R1 and resistance to Foc ST4, while only the diploid CNPMF 0534 demonstrated complete resistance to both R1 and ST4, with resistance to the latter likely associated with penetration. These findings provide valuable insights for banana and plantain breeding programs, offering selected diploids for crossbreeding with commercial cultivars to develop new, resistant genotypes against Foc.

In vitro cancer cell cytotoxicity (IC50 values) of (E)-3-(4’-methylbenzylidene)-4-chromanone (IIIb) showed >50.0 decreases in comparison to those of the respective tetralone derivative (IIIc). On the other hand, such a decrease was not observed in the analogous 4-OCH3 (IIc and IIIc) derivatives. Since the compounds can be considered cyclic chalcone analogs, kinetics and diastereoselectivity of non-enzyme catalyzed reactions with reduced glutathione (GSH) and N-acetylcysteine (NAC) of IIIb and IIIc were investigated to assess the possible role of thiol-reactivity in the increased cytotoxicity of IIIb. Reactivity of the compounds and stereochemical outcome of the reactions were evaluated using high-pressure liquid chromatography-mass spectrometry (HPLC-MS). Molecular modeling calculations were performed to rationalize the observed differences in the thiol-reactivities of the chromanones (III) and the previously investigated tetralones (II). The results indicated possible role of spontaneous thiol-reactivity of compounds III in their recorded biological effects.

Transition-metal-free synthesis of 4-pyrones via TfOH-promoted nucleophilic addition/cyclization of diynones and water has been developed. This transformation is simple, atom economical and environmentally benign, providing rapid and efficient access to substituted 4-pyrones.

The Biginelli reaction is a highly versatile reaction, which leads to dihydropyrimidinones/thiones. This scaffold is reported as being a privileged structure due to its ability to interact with biological targets. Synthesis of ethyl 4-(2-fluorophenyl)-6-methyl-2-thioxo-1-(p-tolyl)-1,2,3,4-tetrahydropyrimidine-5-carboxylate was achieved through the Biginelli reaction using a functionalized thiourea. In silico studies demonstrated that the compound title showed good potential for interacting with ecto-5’-nucleotidase, which has been considered as a target in designs for anti-cancer drugs.

Diabetes mellitus (DM) poses a significant challenge to global health, with its prevalence projected to rise dramatically by 2045. This narrative review explores the bidirectional relationship between periodontitis (PD) and type 1 diabetes mellitus (T1DM), focusing on cellular and molecular mechanisms derived by the interplay between oral microbiota and the host immune response. A comprehensive search of literature published between 2008 and 2023 was conducted to elucidate the association between these two diseases. Preclinical and clinical evidence suggests a bidirectional relationship, with individuals with T1DM exhibiting heightened susceptibility to periodontitis, and vice versa. The review includes recent findings from human clinical studies, revealing variations in oral microbiota composition in T1DM patients, including increases in certain pathogenic species such as Porphyromonas gingivalis, Prevotella intermedia, and Aggregatibacter actinomycetemcomitans, along with shifts in microbial diversity and abundance. Molecular mechanisms underlying this association involve oxidative stress and dysregulated host immune responses, mediated by inflammatory cytokines such as IL-6, IL-8, and MMPs. Furthermore, disruptions in bone turnover markers, such as RANKL and OPG, contribute to periodontal complications in T1DM patients. While preventive measures to manage periodontal complications in T1DM patients may improve overall health outcomes, further research is needed to understand the intricate interactions between oral microbiota, host response, periodontal disease, and systemic health in this population.

Exposure to psychosocial stress is a risk factor for cardiovascular disease, including vascular aging, angiogenesis, and atherosclerosis-based cardiovascular disease (ACVD). Dipeptidyl peptidase-4 (DPP-4) is a complex enzyme (also called CD26) that acts as a membrane-anchored cell surface exopeptidase. DPP4 is upregulated in metabolic and inflammatory cardiovascular disorders. The widespread expression of DPP4 macrophages and immune cells and the noncatalytic function of DPP4 (also called CD26) as a signaling and binding protein across a wide range of species suggest a teleological role for DPP4 in inflammation and immune response. DPP-4 exhibits many physiological and pharmacological functions by regulating its extremely abundant substrates [e.g., stromal cell-derived factor-1α/ C-X-C chemokine receptor type-4, glucagon-like peptide-1 (GLP-1), etc.]. Over last ten year, emerging data demonstrated unexpected roles for GLP-1 and DPP-4 in extracellular and intracellular signaling, immune activation, inflammation, oxidative stress production, cell apoptosis, insulin resistance, and lipid metabolism,. This mini review has focuses on recent novel findings in this field, highlighting an imbalance between GLP-1 and DPP4 as a potential therapeutic molecular target in treatments of chronic psychological stress-related atherosclerotic cardiovascular disease in humans and animals.

We report here the synthesis and characterization of new N-(3-(8-bromoimidazo[1, 2-a]pyridin-2-yl)-4-fluorophenyl)benzamide derivatives. This collection was obtained from 3-(8-bromoimidazo [1,2-a]pyridin-2-yl)-4-fluoroaniline(5). The family of new compounds was characterized by ¹H-NMR, ¹³C-NMR, FT-IR and LC-MS analysis.

Traditional lime-based materials have considerable potential for use as components of green materials for plastering and finishing building surfaces in both new construction and historic heritage conservation. The paper presents the preliminary results of a research activity aimed at developing pre-packaged products based on Traditional Lime Putty (TLP) by partially replacing natural aggregates with Stone Waste Sludge (SWS), with a low rate of recovery from Apricena limestone production district in Apulia. The mineralogical and chemical analysis carried out by means XRD (X-Ray Diffraction), TG-DTA (Thermo Gravimetry-Differential Thermal Analysis) and hydrochloric acid attack test showed that the SWS consisted of 98.4 % CaCO3 by mass. The particle sizes measured by laser diffraction technique are below 22.5 μm for the 92% by mass of the sample. The high fineness of the stone waste was confirmed by the Blaine specific surface method equal to 9273.79 cm2/gr. The behavior of three fresh mixtures for prepacked coarse plaster, fine plaster, and finishing plaster with 12.90%, 17.94%, and 18.90 by mass of SWS, respectively, was evaluated by spreading test and applicability tests on a perforated ceramic slab. The finishing plaster has the highest consistency value of 235 mm, while the fine plaster and the coarse plaster have values of 205 mm and 155 mm, respectively. The coarse plaster is suitable for the use as base plaster (arriccio) or second layer rendering (tonachino) up to a thickness of approximately 1 cm. Both the fine plaster and finishing plasters can be used for the surfaces finishing with the application of layers of a few millimeters thick.

The regulation of cell death is a fundamental issue in cell biology and continues to be intensely investigated worldwide. The significance of research in this field persists because understanding the determinants of cell lifespan directly impacts the maintenance of multicellular organism homeostasis and, consequently, is crucial for addressing biomedical challenges associated with various diseases. It is recognized that the initiation of cell death can be prompted by both specific signals (such as cytokines or hormones) and nonspecific stimuli, including radiation, temperature increase, or oxidants. When these factors affect a cell, numerous signaling pathways are triggered in the cell, leading to neutralization of the effects of their negative effects or, in case of irreparable damage, to cell elimination. This removal of damaged cells occurs through apoptosis or programmed cell death, a highly regulated process. Numerous signaling molecules participate in orchestrating the apoptotic process, many of which also govern other essential functions within the organism. Physiological factors capable of triggering the apoptotic program in cells include nitric oxide (NO), which serves as one of the key signaling molecules regulating the functions of the cardiovascular, nervous, and immune systems of the organism. The unique chemical nature of NO, along with its numerous intracellular targets and physiologically active redox forms, raises questions about the specific mechanisms through which NO exerts its damaging effects on cells. Utilizing pharmacological preparations- such as sources (donors) of exogenous nitric oxide- represents an approach to investigating the initiation and execution of the apoptotic program in sensitive target cells. Furthermore, this approach holds promise as a direction for discovering new selective drugs.

With increasing concerns over environmental impact, and overall health of both the environment and its people, a need to quantify contaminants is of the utmost importance. Chemosensors with low detection limits and relative ease of application can address this challenge. Nitrite ions are known to be detrimental to both the environment and human health. A new colorimetric chemodosimeter has been prepared from a homolytic photochemical cleavage of a reaction between pyrrole and pyridine. The product, 4(pyrrol1-yl)pyridine, yields a limit of detection of 0.330 (±0.09) ppm for the detection of nitrite in aqueous solution, employing a colorimetric change from yellow to pink. It is also highly selective for nitrite when various competitive anions such as SO32- , NO3-, PO43-, SO4-2, Cl-, F-, I-, Br-, and CN- are present in great excess. The molecule’s especially high sensitivity to nitrite is apparently the result of a complex supramolecular mechanism, characterized by both dynamic light scattering of the aggregate and the Tyndall effect. Consequently, this new sensor provides a simple, low-cost way to rapidly detect nitrite anions in aqueous solution.

In this paper the one-to-one correspondences and equivalences between ideals, primals, filters and grills are introduced. It is shown the local functions and the topological spaces induced by them are the same. From this point of view, the topological properties with respect to one topology can be derived from topological properties valid in the corresponding topology.

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

In this study, a composite film was developed for electrochemical sensing of tryptophan (Trp). Porous reduced graphene oxide (PrGO) was utilized as the electron transfer layer, and a C-undecylcalix[4] resorcinarene Langmuir-Blodgett (CUCR-LB) film served as the molecular recognition layer. Atomic force microscopy (AFM), transmission electron microscopy (TEM), Raman spectroscopy, scanning electron microscopy (SEM), and electrochemical experiments were employed to analyze the characteristics of the CUCR-LB/PrGO composite film. The electrochemical behavior of Trp on the CUCR-LB/PrGO composite film was investigated, revealing a linear response range of Trp was 1.0×10-7 to 3.0×10-5 mol L-1 and a detection limit of 3.0×10-8 mol L-1. Furthermore, the developed electroanalytical method successfully determined Trp content in an amino acid injection samples. This study not only introduces a rapid and reliable electrochemical method for determination of Trp but also presents a new strategy for constructing high-performance electrochemical sensing platforms.

A simple protocol for preparation of O-acylated enol form - (R/S)-ethyl-2-acetoxy-4-phenyl-4H-chromene-3-carboxylate 5 was presented. The compound was characterized by 1H-, 13C-and DEPT135 NMR spectra, including {1H,1H} COSY, {1H,13C} HSQC, {1H,13C} HMBC and 2D-NOESY spectra. The preferred regioselectivity for O-acylation of 3,4-dihydrocoumarin 5 in the presence of substituent in 4-th position in the chroman ring and accounting the steric hindrance of the ester group in 3-th place was confirmed.

The proper hydrogenation of Hyper-coal (HPC) using 1, 2, 3, 4-tetrahydroquinoline (THQ) was able to decrease the oxygen content and adjust the molecular structure of HPC for preparing the spinnable pitch with high softening point (SP). The spinnable pitch prepared from the THQ-soluble (QS) fraction of HPC as a precursor consisted more naphthenic carbon groups than that prepared from the 1-methylnaphthalene (1-MN) soluble (MNS) fraction of HPC. The HPC-QS derived pitch showed excellent spinnability even the SP of 260°C, and the tensile strength of the resultant carbon fiber was up to 1350 MPa with a diameter around 8 µm by only heat treatment at 800°C for 5 min.

PVC items are environmentally friendly as, unlike polyolefins, they are mainly based on chlorine, one of the most abundant elements on earth. However, in the eco-design context, articles' durability plays the crucial role, contributing to the enhancement of their sustainability. In this framework the research on additives capable of increasing the weatherability of outdoor articles is essential. The theory section of the paper reviews the mechanisms of weathering leading to PVC degradation that undermine the durability of items such as window frames or roller shutters. The weathering of PVC items is a complex phenomenon involving photo-chemical and secondary chemical reactions, that yields the formation of conjugated polyene sequences underskin in absence of oxygen and carbonyls in the surface. Here the chain scission of the polymer backbone occurs, bringing the disintegration of the surface of the item and causing the typical discoloration called chalking, especially evident in dark-colored articles. In the experimental section of the paper the effect of different acid scavengers on the item weathering has been studied with natural outdoor and two accelerated exposures, xenon-arc and Q-UV testing devices. Results confirm that some acid scavengers are efficient in preventing chalking, but some are ineffective or even detrimental. Thus, the PVC formulations of durable articles upon weathering still depend on a complex choice of the appropriate ingredients, and several outdoor and indoor accelerated weathering tests are needed to predict the articles' lifetime.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Background: This study retrospective evaluates patients with stage IV melanoma treated with Nivolumab and Ipilimumab combination therapy from two regional oncology centers from Romania between the years of 2019 up to the end of 2022. Methods: The data were analyzed in SAS for Windows, V9.4. The survival curves were estimated using the Kaplan-Meier method, and survival distributions were compared with log-rank test. The effects of the main clinical and pathological variables on OS and PFS were investigated with Cox regression. Results: Kaplan-Meier curve of OS in all evaluable patients enrolled in the study resulted in a median OS of 346 days (95% CI: 150-NA) and a median PFS of 211 days (95% CI: 113-430). 45.3% of the patients experienced adverse events during the Nivolumab + Ipilimumab treatment with some of them having multiple organ systems involved. Discussion: The OS values were lower than that reported in approval clinical trials, but the results show a marked improvement when comparing to results obtained by chemotherapy regimens previously used in these scenarios. Conclusion: This study provides real-world insights into the survival data and safety profiles of combination therapy with anti-PD-1 antibodies and anti-CTLA-4 antibodies.

Background. Transferrin receptor 1 (TfR1), glucose transporter 1 (GLUT1), and CD98hc are candidates for targeted therapy at the blood-brain barrier (BBB). Our objective was to challenge the expression of TfR1, GLUT1, and CD98hc in brain capillaries by the histone deacetylase inhibitor (HDACi) valproic acid (VPA). Methods. Primary mouse brain capillary endothelial cells (BCECs) and brain capillaries isolated from mice injected intraperitoneally with VPA were examined using RT-qPCR and ELISA. Targeting to the BBB was performed by injecting monoclonal anti-TfR1 (Ri7217)-conjugated gold nanoparticles measured using ICP-MS. Results. In BCECs co-cultured with glial cells, Tfrc mRNA expression was significantly higher after 6 h VPA returning to baseline after 24 h. In vivo Glut1 mRNA expression was significantly higher in males, but not females', receiving VPA, whereas Cd98hc mRNA expression was unaffected by VPA. TfR1 increased significantly in vivo after VPA, whereas GLUT1 and CD98hc were unchanged. Uptake of anti-TfR1-conjugated nanoparticles was unaltered by VPA in spite upregulated TfR expression. Conclusions. VPA upregulates TfR1 in brain endothelium in vivo and in vitro. VPA does not increase GLUT1 and CD98hc proteins. The increase in TfR1 does not result in higher anti-TfR1 antibody targetability, suggesting targeting sufficiently occurs with available transferrin receptors without further contribution from accessory VPA-induced TfR1.

Nowadays, animal breeders look for effective innovations to care animal health. Use of probiotics, postbiotics, parabiotics and the other beneficial natural substances are dominated. Mundticin-like substance EM 41/3 is thermo-stable bacteriocin (postbiotic) with a broad antimicrobial spectrum. In this study its effect in broiler rabbits was assessed. Rabbits represent food-derived animal and they are also suitable animal model. The parameters tested were analyzed by validated methods. Administration of MLS EM 41/3 produced by non-autochthonous strain Enterococcus mundtii EM 41/3 lead to significant increase of parameter immunity-phagocytic activity, while it did not influence microbiota composition. It also did not influence blood biochemistry and no oxidative stress was noted. Moreover, higher growth parameters were noted and also stimulated hydrolytic activity. Finally, no negative influence on rabbit meat quality was noted. Postbiotic MLS EM 41/3 administration in feeding strategy seems to be contributing fact for rabbit health status maintaining.

This study proposes an innovative pharmacovigilance approach, VIGI-4, leveraging ChatGPT Teams Pro version. Our method involves aggregating data from all phase 4 studies published in February 2024 to identify adverse reactions. These results are categorized by disease state alphabetically, demonstrating the method's capacity to generate structured and easily navigable outputs. The results section is tailored to exemplify the valuable, actionable insights attainable through our workflow. This research emphasizes the game-changing potential of integrating advanced technologies such as ChatGPT into pharmacovigilance, signaling a new era in safeguarding drug safety.

Our environment has been significantly impacted by man-made pollutants, primarily due to industries make substantial use of synthetic chemicals, resulting in significant environmental consequences. In this research investigation, the co-precipitation approach was employed for the synthesis of cellulose-based ferric oxide (Fe₂O₃/cellulose) and copper oxide nanoparticles (CuOx-NPs). Scanning electron microscopy (SEM) analyses were conducted to determine the properties of the newly synthesised nanoparticles. Furthermore, the synthesized nanoparticles were employed for eliminating chromium from aqueous media under various conditions, including temperature, contact time, adsorbent concentration, adsorbate concentration, and pH. Additionally, the synthesised materials were used to recover Cr(VI) ions from real samples, including tap water, seawater, and industrial water, and the adsorptive capacity of both materials evaluated under optimal conditions. The synthesis of Fe₂O₃/cellulose and CuOx-NPs proved to be effective, as indicated by the outcomes of the study.

4-(2-Methyloxazol-4-yl)benzenesulfonamide was synthesized by the reaction of 4-(2-bromoacetyl)benzenesulfonamide with an excess of acetamide. The obtained compound was evaluated as a potential inhibitor of human monoamine oxidase (MAO) A and B and was found to inhibit these enzymes with IC50 values of 3.47 μM for MAO-B and 43.3 μM for MAO-A. Thus, the new selective MAO-B inhibitor was identified, which may be used as the lead compound for development anti-Parkinson’s disease agents.

This paper presents the PEnsemble 4 model, a sophisticated machine learning framework that integrates IoT-based environmental data to accurately forecast maize yield. With the projected significant growth in global maize demand over the next decade, the inherent risks posed by the crop’s dependence on weather conditions necessitate improved prediction capabilities. The PEnsemble 4 model, developed with high accuracy, incorporates comprehensive datasets encompassing soil attributes, nutrient composition, weather conditions, and UAV-captured vegetation imagery. By employing a combination of Huber and M estimates, the PEnsemble 4 model effectively analyzes temporal patterns in vegetation indices, specifically CIre and NDRE, which serve as reliable indicators of canopy density and plant height. In addition, this research significantly contributes to precision agriculture by offering an efficient and sustainable alternative to conventional farming practices through precise yield predictions. Notably, the PEnsemble 4 model enables earlier estimation, advancing the timeline for yield prediction from the conventional day 100 in the R6 stage to day 79 in the R2 stage. This improvement enhances decision-making processes in farming operations. The remarkable accuracy rate of 91% underscores the importance of adopting a multifaceted data approach that harnesses IoT-derived environmental insights. Additionally, the PEnsemble 4 model extends its benefits beyond yield prediction, facilitating the detection of water and crop stress, as well as disease monitoring in broader agricultural contexts. Ultimately, the PEnsemble 4 model establishes a new standard in maize yield prediction, revolutionizing crop management and protection through the synergistic utilization of IoT and machine learning technologies.

Density functional theory (DFT) and coupled cluster theory (CCSD(T)) calculations are performed to investigate the geometric, electronic structures and chemical bonding of a series of Cu-doped zinc oxide clusters, CunZn3O3 (n = 1-4). The structural evolution of CunZn3O3 (n = 1-4) clusters are elaborated in our work. The planar seven-membered ring of CuZn3O3 cluster plays an important role in the structural evolution, that is, the Cu atom, Cu dimer (Cu2) and Cu trimer (Cu3) anchor on the CuZn3O3 cluster. The aggregate behavior of Cu atoms on Zn3O3 may offer insight into the study of Cu/ZnO-based catalysts. Additionally, it is found that the CunZn3O3 clusters become more stable as the Cu content (n) increases. Bader charge analysis points out that as the Cu atoms doping, the reducibility of Cu aggregation (Cun-1) on the CuZn3O3 cluster increases. Combined with the d-band centers and the surface electrostatic potential (ESP), the reactivity and the possible reaction sites of CunZn3O3 (n = 1-4) clusters are also illustrated.

DFT calculations on the photoisomerization reactions of pyridazine N-oxide derivatives are presented. The irradiation of 3,6-diphenylpyridazine N-oxide allowed to obtain the first excited singlet state that underwent to a ring opening reaction induced to the oxygen migration to the adjacent carbon atom, with the formation of a diazo derivative. This intermediate can give a ring closure reaction to give a pyrazole derivative, or, with a higher transition energy, it can lose nitrogen allowing the formation of 2,5-diphenylfuran. The irradiation of 3-phenylpyridazine N-oxide allowed the formation only of 2-phenylfuran. In this case, calculations allowed to explain this behavior. The first excited singlet state gave a photoisomerization reaction with the formation of the corresponding diazo intermediate. This intermediate could not be converted into the corresponding pyrazole derivative because it was converted into a N-formyl pyrazole never reported in literature. The only possible reaction is the loss of nitrogen and the formation of 2-phenylfuran.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

Lifestyle interventions can prevent type 2 diabetes (T2DM). However, some in-dividuals do not experience anticipated improvements despite weight loss. Bi-omarkers to identify such individuals at early stages are lacking. IGF-1 and IGFBP-1 were shown to predict T2DM onset in prediabetes. We assessed if these markers also predict the success of lifestyle interventions, thereby possibly guid-ing personalized strategies. We analyzed fasting serum levels of IGF-1, IGFBP-1 and IGFBP-2 in relation to changes in metabolic and anthropometric parameters, including intrahepatic li-pids (IHL) and visceral adipose tissue (VAT) volume measured by MRI, in 345 high-risk prediabetic participants (54% female; aged 36-80 years). Participants were enrolled in three randomized dietary intervention trials and assessed both at baseline and one year post-intervention. Statistical analyses were performed using IBM SPSS Statistics (version 28), significance set at p

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Dengue is a viral mosquito-borne disease that rapidly spreads in tropical and subtropical countries, including the Philippines. One of its most distinguishing characteristics is the ability of the Dengue Virus (DENV) to easily surpass the innate responses of the body, thus activating B cells of the adaptive immunity to produce virus-specific antibodies. Moreover, Dengvaxia® is the only licensed vaccine for DENV, but recent studies showed that seronegative individuals become prone to increased disease severity and hospitalization. Owing to this limitation of the dengue vaccine, this study determined and compared consensus and unique B cell epitopes among each DENV (1-4) Philippine isolate to identify potential areas of interest for future vaccine studies and therapeutic developments. An in silico-based epitope prediction of forty (40) DENV 1-4 strains, each serotype represented by ten (10) sequences from The National Center for Biotechnology Information (NCBI), was conducted using Kolaskar and Tongaonkar antigenicity, Emini surface accessibility, and Parker hydrophilicity prediction in Immune Epitope Database (IEDB). Results showed that five (5) epitopes were consensus for DENV-1 with no detected unique epitope, one (1) consensus epitope for DENV-2 with two (2) unique epitopes, one (1) consensus epitope for DENV-3 plus two (2) unique epitopes, and two (2) consensus epitopes and one (1) unique epitope for DENV-4. The findings of this study would contribute to determining potential vaccine and diagnostic marker candidates for further research studies and immunological applications against DENV (1-4) Philippine isolates.

IL1RA intron 2 86-bp repeat and IL4 intron 3 70-bp repeat are VNTRs that have been associated with various diseases, but their role in obesity is elusive. The objective of this study was to investigate the association of IL1RA and IL4 VNTRs with obesity and adiposity in 315 Malaysian subjects (128 M/187 F; 23 Malays/251 ethnic Chinese/41 ethnic Indians). The allelic distributions of IL1RA and IL4 were significantly different among ethnicities, and the alleles were associated with total body fat (TBF) classes. Individuals with IL1RA I/II genotype or allele II had greater risk of having higher adiposity - even after controlling for ethnicity [Odds Ratio (OR) of I/II genotype = 12.21 (CI = 2.54, 58.79; p = 0.002); II allele = 5.78 (CI = 1.73, 19.29; p = 0.004)]. However, IL4 VNTR B2 allele was only significantly associated with overall adiposity status before adjusting for ethnicity [OR = 1.53 (CI = 1.04, 2.23; p = 0.03)]. TBF was also significantly higher in those with IL1RA II allele compared with I allele (31.79 ± 2.52 vs. 23.51 ± 0.40; p = 0.005). Taken together, IL1RA intron 3 VNTR seems to be a genetic marker for overall adiposity status in Malaysian subjects.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Antibiotic prescription is the first line of treating bacterial diseases. But it affects the composition and function of non-targeted intestinal microbiota. Antimicrobial resistance will be the cause for the death of millions of people worldwide. By considering collateral damage of antibiotics, searching an alternative antimicrobial agent will be a solution to minimize the problems. Probiotics, prebiotics and synbiotics are an alternative to antibiotics. Thanks to GIT microbes as they are responsible for metabolism, energy production, protection from pathogens and immunomodulation. So, it is appreciable if the gut microbiota modulated through consumption of probiotics, prebiotics and synbiotics. Probiotic effects are genus and species specific. To get good health benefit of probiotics, safety of probiotics should be assessed before using them. This is mandatory for prebiotics and synbiotic selection. So this review paper gives information about side effects of antibiotics on gut microbiota, description of probiotics, prebiotics and synbiotics as alternative to antibiotics in modulating GIT microbiota, techniques of assessing safety of probiotics and health benefits of probiotics, prebiotics and synbiotics with scientific evidence in clinical trial and some disagreement and challenges of using probiotics, prebiotics and synbiotics.

Background: Amyloid beta peptides (Aβ) have been identified as the main pathogenic agents in Alzheimer’s disease (AD). Soluble Aβ oligomers, rather than monomer or insoluble amyloid fibrils, show membrane-binding capacity to red blood cells (RBCs) and trigger several morphological and functional alterations in RBCs that can result in impaired oxygen transport and delivery. Since bioactive lipids have been recently proposed as potent protective agents against Aβ toxicity, we investigated the role of sphingosine-1-phosphate (S1P) in signaling pathways involved in the mechanism underlying ATP release in Aβ-treated RBCs. Methods: In RBCs following different treatments, ATP, 2,3 DPG, cAMP levels, and caspase 3 activity were determined by spectrophotometric and immunoassay. Results: S1P rescued the inhibition of ATP release from RBCs triggered by Aβ through a mechanism involving caspase-3 and restoring 2,3 DPG and cAMP levels within the cell. Conclusions: These findings reveal the molecular basis of S1P protection against Aβ in RBCs and suggest new therapeutic avenues in AD.

We define a spinor-Minkowski metric for SL(4,C). It is not a trivial generalization of the SL(2,C) metric and it involves the Minkowskian one. We define 4x4 version of the Pauli matrices and eight 4-component associated generalized eigenvectors that can be regarded as undotted covariant spinors. The 4-component spinors can be grouped into four categories. Each category transforms in its own way. The outer products of pairwise combinations of 4-component spinors can be associated with 4-vectors. Including the dotted covariant, undotted and dotted contravariant forms totally we have sixteen pairs of spinors. Eight of them live in the conjugate space which has no countepart in SL(2,C).

Non-enzyme-catalyzed thiol addition onto the α,β-unsaturated carbonyl system is associated with several biological effects. Kinetics and diastereoselectivity of non-enzyme catalyzed nucleophilic addition of GSH and NAC to the six-membered cyclic chalcone analogs 2a and 2b were investigated at different pH values (pH 3.2, 7.4 and 8.0). The selected compounds displayed in vitro cancer cell cytotoxicity (IC50) of different orders of magnitude. The chalcones intrinsically reacted with both thiols under all incubation conditions. The initial rates and compositions of the final mixtures depended both on the substitution and the pH. The stereochemical outcome of the reactions was evaluated by HPLC-UV method. The structure of the formed thiol-conjugates and the retro-Michael products (Z)-2a and (Z)-2b were confirmed by HPLC-MS. The frontier molecular orbitals and the Fukui function were carried out to investigate their effects on the six-membered cyclic analogs. Data were compared with those obtained with the open-chain (1) and the seven-membered (3) analogs. The observed reactivities do not directly relate to the difference in in vitro cancer cell cytotoxicity of the compounds.

The article presents the results of studies aimed to identify the effect of foliar treatments of winter wheat, sugar beets and soybeans with mineral and bioorganic fertilizers. Their positive effect on increasing the concentration of mineral forms of nitrogen in soil was revealed. The crop types have a greater influence on the size of nitrous oxide emissions: in winter wheat crops - 679 µg/m3, soybeans - 637.2 µg/m3, sugar beets - 576.8 µg/m3. The amounts of nitrous oxide emissions were lower in the variants without the use of phosphorus-potassium fertilizers. The Ruter AA fertilizer showed the greatest efficiency on winter wheat crops - 42.7 c/ha. Soybean grain yield of 44.2 c/ha was also achieved by using Ruter AA, as well as Geo-humate together with phosphorus-potassium fertilizers. On the background of the actual supply of phosphorus and potassium, maximum yield was obtained when using N30 on the leaf - 39.3 c/ha. Foliar feeding ensured a yield of sugar beet root crops of up to 67.1-77.4 c/ha on the backdrop of the application of phosphorus-potassium fertilizers with the advantage of using Amino turbo. The largest yield of sugar beet roots without use of mineral phosphorus and potassium was ensured by N30 treatment of the leaf in the phases of 4-6 and 8 leaves - 63.2 t/ha. Of the organo-mineral fertilizers and biostimulants, the best result was shown by the use of Ruter A - 62.6 t/ha. We believe that foliar feeding of crops can be a sustainable farming method that can increase crop yields and reduce N2O emissions.

Herein, two title compounds, N-Benzoyl-N’-4-cyanophenyl thiourea (I) and N-(4-nitrobenzoyl)-N’-4-cyanophenyl thiourea (II) were synthesized in high yield, via aroyl isocyanate and 4-aminobenzonitrile. The structure of the prepared compounds was characterized by elementary analysis and FT-IR, ¹H, ¹³C NMR spectroscopic methods. Cyclic voltammetric (CV) experiments were performed with glassy carbon electrode. The reduction potential values of different functional group such as nitro, cyano in title compounds were investigated using CV curves.

Introduction The monitoring of cerebral perfusion in patients with brain damage is a major clinical challenge. Monitoring cerebral oxygenation (rSO2) by NIRS was introduced at the turn of the 1980s, and many clinicians believed it was a valuable method for assessing cerebral perfusion and subsequent measures to optimize cerebral flow. The main problem of NIRS usage is the presence of the intermediate structures-skin, skull, meninges, cerebrospinal fluid-and their influence on the outcome of the test. Therefore, it seems that NIRS assessment performed on a patient during brain death attempts, can give an idea of the magnitude of the influence of these intermediate structures on the monitoring result. Case We present a retrospective analysis of cerebral oxygenation measurements of a patient undergoing a brain death diagnostic procedure. A clinical situation where the cerebral blood flow is stopped can give an idea of the specificity of the method, particularly the impact of the influence of intermediate structures on the monitoring outcome. In this case, the NIRS result is increased by the oxygenation of the patient before the apnoea test. The influence of chromophores in the tissues surrounding the CNS, reflections and scattering of the light wave spectrum have a very significant effect on the final result of cerebral saturation measurement. Discussion The majority of research observations describing changes in cerebral perfusion or its optimisation may be burdened by the problem described, i.e. the significant influence of measured oxygenation from intermediate structures. The specificity of NIRS to assess cerebral perfusion requires careful analysis. The therapeutic implications of monitoring cerebral oxygenation with NIRS are of great importance and, from the example presented and the literature provided, the method should be used with caution. It has been shown that in a patient with brain death, the result of NIRS oxygenation measurements depends on the surrounding structures of the brain.

Alcoholic liver disease (ALD) develops when the immunotolerant environment of the liver is compromised due to excessive alcohol consumption. ALD progression involves variations in the expression of multiple genes, resulting in liver inflammation and the development of a leaky gut. Molecular mechanism involved for ALD progression is still unclear, and due to that there are currently no FDA-approved drugs available for its treatment. In this study, the protective effects of Graphene oxide nanoparticles (GO) was investigated against ethanol-induced damage in the gut-liver axis in in vitro. GO was synthesized using a modified Hummer's method and characterization was done. Given the general concerns regarding nanoparticle toxicity, assessment of cell viability, lipid accumulation, DNA damage, cell death, and the generation of reactive oxygen species (ROS) were conducted using various techniques. Furthermore, gene expression of pro- and anti-inflammatory cytokines was done using RT-qPCR. The findings revealed that GOs promoted cell viability even against ethanol treatment. Additionally, lipid accumulation significantly decreased when cells were treated with GO alongside ethanol compared to ethanol treatment alone, with similar trends observed for other assays. Gene expression analysis indicated that GO treatment reduced the expression of proinflammatory cytokines while enhancing the expression of antioxidant genes. Moreover, GO treatment led to improvements in gut permeability and a reduction in proinflammatory cytokines in colon cells damaged by ethanol. These findings suggest that GO holds promise as a drug carrier, exhibiting no observed toxic effects. By shedding light on the protective effects of GO against ethanol-induced damage, this study contributes to the burgeoning field of nanoparticle-mediated therapy for ALD.

A field experiment was conducted for 2 years in Green Tea Laboratory of Saitama Prefectural Agriculture and Forestry Research Center, Iruma, Saitama, Japan from March 2014 to December 2015. Controlled release fertilizers (CRF) or organic fertilizers (ORG) which is the mixture of chicken manure and oil cakewere applied with the amount of 450 kg N ha^-1 yr^-1 in 2014 and 397 kg N ha^-1 yr^-1 in 2015. Nitrous oxide (N₂O) emissionsfrom soil in green tea fields were measured by closed chamber method. The results showed that CRF has significantly lower N₂O compared to ORG. The cumulative N₂O emissions from CRF accounted for 51% of N₂O emissions from ORG fields and 138% of control with no fertilizer treatment. The N₂O flux from the row was higher than that of under the canopy, since fertilizer were applied on the row. However the total emission from the area between the rows was lower than that under the canopy because of the area ratio of row and canopy was 1:5.

Multiple myeloma (MM) is characterized by the malignant proliferation of monoclonal plasma cells in the bone marrow with an elevation in monoclonal paraprotein, renal impairment, hypercalcemia, lytic bony lesions, and anemia. Immune cells and associated cytokines play a significant role in MM growth, progression, and dissemination. While some cytokines and their clinical significance are well described in MM biology, others remain relatively unknown. The aim of the present study was to assess the impact of pretreatment serum levels of 27 selected cytokines on progression-free survival (PFS) and overall survival (OS) in MM patients before first-line therapy with bortezomib-based regimens. Serum cytokine levels were assayed with a Bio-Rad Bio-Plex Pro Human Cytokine 27-Plex Assay on the MAGPIX Multiplex Reader and the Bio-Plex® 200 System (Bio-Rad) including IL-1β, IL-1Ra, IL-2, IL-4, IL-5, IL-6, IL-7, IL-8, IL-9, IL-10, IL-12, IL-13, IL-15, IL-17, Eotaxin, FGF, G-CSF, GM-CSF, IFN-γ, IP-10, MCP-1, MIP-1α, MIP-1β, PDGF-BB, RANTES, TNF-α, and VEGF. A total of 61 MM patients were examined. Most patients received a bortezomib, cyclophosphamide and dexamethasone (VCD) chemotherapy regimen. In the final multivariate model, IL-13 cytokine level (HR 0.1411, 95% CI: 0.0240-0.8291, p = 0.0302), and ASCT (HR 0.3722, 95% CI: 0.1826-0.7585, p=0.0065) significantly impacted PFS. Furthermore, ASCT (HR 0.142, 95% CI: 0.046-0.438, p=0.0007), presence of bone disease at diagnosis (HR 3.826, 95% CI: 1.471-9.949, p=0.0059) and two cytokine levels- IL-1Ra (HR 1.017, 95% CI: 1.004-1.030, p= 0.0091) and IL-4 (HR 0.161, 95% CI: 0.037-0.698, p = 0.0147) were independent predictors of OS. Three clusters of MM patients were identified with different cytokine profiles. In conclusion, serum pretreatment levels of IL-13 and IL-4 are predictors of better PFS and OS, respectively, whereas IL-1Ra pretreatment levels negatively impact OS in MM patients treated with bortezomib-based chemotherapy. Cytokine signature profile may have a potential influence on the outcome of patients treated with bortezomib.

A new heterocyclic compound, 2-(2,6-diisopropylphenyl)-1-methylimidazo[1,5-a]quinolin-2-ium tetrafluoroborate 1 was obtained from its precursor, N-(2,6-diisopropylphenyl)-N-(quinolin-2-ylmethyl)acetamide 2, by POCl3-mediated cyclization. For the first time – the tertiary acetamide 2, precursor of 1, was synthesized by using commercially available starting materials. The structure of 1 was unquestionably confirmed by 1H-, 13C-, 2D-NMR-, IR- spectroscopy and mass-spectrometry. Its optical properties were also studied.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Hydrological processes are complex to compute on hilly areas when compared to the plain areas. Most of the hydrological model do not take into account the critical rainfall-runoff generation processes such as subsurface storm flow, saturation excess flow, overland flow, return flow and pipe storage. The simulations of the above processes in the soil matrix requires detailed hillslope hydrological modelling. In present study, a hillslope experimental plot is designed to study the runoff generation processes on the plot scale. The setup is designed keeping in view the natural hillslope conditions prevailing in the north western Himalayas, India where high intensity storm event occurs frequently. Using the experimental data and the developed conceptual model, the overland flow and the subsurface flow through macropore dominated area has been estimated/analyzed on the pixel basis. Over the experimental hillslope plot, a rainfall simulator was installed to generate the rainfall intensity in the range of 15 to 150 mm/hr which represented the dominating rainfall intensity range in the region. Soil moisture sensors were also installed at 100 mm and 300 mm depth at different locations of the plot to observe soil moisture variations. It was found that once the soil is saturated, it remains in the field capacity for next 24-36 hours. Such antecedent moisture conditions are most favorable for the generation of rapid stormflow from hillslopes. Dye infiltration test was also performed on the undisturbed soil column to observe the macropore fraction variability over the vegetated hillslopes. The surface runoff predicted using the developed hillslope hydrological model compared well with the observed surface runoff under high intensity rainfall conditions.

Reverse engineering is applied to identify optimum polymerization conditions for the synthesis of polymer with pre-defined properties. The proposed approach uses multi-objective optimization (MOO) and provides multiple candidate polymerization procedures to reach the targeted polymer property. The objectives for optimization include maximal similarity of molar mass distributions (MMD) compared to the target MMD, minimal reaction time, and maximal monomer conversion. The method is tested for vinyl acetate radical polymerizations and can be adopted to other monomers. The data for the optimization procedure is generated by an in-house developed kinetic Monte-Carlo (kMC) simulator for a selected recipe search space. The proposed reverse engineering algorithm comprises several steps: kMC simulations for the selected recipe search space to derive initial data, performing MOO for a targeted MMD, and identification of the Pareto optimal space. The last step uses a weighted sum optimization function to calculate the weighted score of each candidate polymerization conditions. To decrease the execution time clustering of the search space based on MMDs is applied. The performance of the proposed approach was tested for various target MMDs. The suggested MOO-based reverse engineering provides multiple recipe candidates depending on competing objectives.

This work focuses on the theoretical study of the effect of entanglement in the Yttrium Barium Copper Oxide (YBCO) superconductor on the critical current density, critical magnetic field, and penetration depth. Using the Ginzburg Landau (GL) theory, the expression for the GL coherence length, the critical current density, the lower critical magnetic field (Hc1), and the upper critical magnetic field (Hc2) for the entangled superconducting YBCO was obtained. At zero external magnetic fields, YBCO was found to undergo a transition from the normal state to the superconducting state at 93K and returned to normal. We found a direct relationship between the GL coherence length penetration depth and the temperature of the entangled superconducting YBCO. The graphs of the lower critical magnetic field (Hc1) and critical current density against temperature show a non-linear dependence.In contrast, the graph of the upper critical magnetic field (Hc2) against temperature (T) shows the linear dependence, which is in agreement with existing theoretical observations. On the other hand, the graph of critical current density against the distance of separation between the entangled electrons that form a cooper pair showed that the critical current density increases between 1.8 and 6 nanometers attaining a constant value after reaching 7 nanometers for infinite distances. Finally, for lower critical fields, the magnetic field decreases between 1.5 to 6 nanometers attaining a constant value of the magnetic field, for infinite values of distance of separation between the entangled pair of electrons.

An oxidation resistant coating on cemented tungsten carbides is characterised in this work. Cemented tungsten carbides (cWCs) are routinely used in mining and manufacturing but are also candidate materials for compact radiation shielding in fusion power generation. In both environments, cWCs will suffer significant degradation due to oxidation at relatively low temperatures. In a recent study, a Si-deposition coating method was demonstrated to improve the oxidation resistance of cWCs by up to a factor of 1,000. This work focusses on the growth kinetics, phase composition, and mechanical properties of these coatings. By combining quantitative X-ray diffraction, electron microscopy and nanoindentation, we show that the coating layer has a 20 % higher hardness than the substrate, which was explained on the basis of a previously-unknown presence of a fine distribution of very hard SiC laths. To interpret the coating stability, a coating growth map is developed. The map shows the structure is stable under a broad range of processing temperatures and composite compositions, demonstrating the potential application of these coatings in a variety of nuclear shielding cWCs.

Abiotic stress is responsible for significant reduction in crop plant productivity worldwide. Ultraviolet (UV) radiation is a natural component of sunlight and a permanent environmental stimulus. This study investigated the distinct responses of young wheat and einkorn plants to excessive UV-B radiation (180 min at λmax 312 nm) following foliar pretreatment with 1 µM synthetic cytokinin 4PU-30. Results demonstrated that UV radiation significantly amplified hydrogen peroxide levels in both wheat and einkorn, with einkorn exhibiting more pronounced increase compared to wheat. This elevation indicated the induction of oxidative stress by UV radiation in the two genotypes. Intensified antioxidant enzyme activities and increased accumulation of typical stress markers and non-enzyme protectants were evidenced. Transcriptional activity of genes encoding key antioxidant enzymes was also investigated aiming to elucidate the genetic regulation of the antioxidant systems in both wheat and einkorn seedlings. Our results suggested a role for POX1 and POX7 genes in the UV-B tolerance of the two wheat species as well as a cytokinin stimulated UV-B stress response in einkorn mediated through upregulation of the tau subfamily gene GSTU6. Based on these findings it could be concluded that 4PU-30 had the potential of alleviating oxidative stress by attenuating the symptoms of superfluous UV-B illumination in the two examined plant species.

Molecular-scale density fluctuations at equilibrium produce cavities in a liquid and can be analyzed to shed light on the statistics of the number of molecules occupying observation volumes of increasing radius. An information theory approach led to the conclusion that these probabilities should follow a Gaussian distribution function. This prediction has been confirmed by computer simulations in different liquid models if the size of the observation volume is not large. The reversible work of cavity creation is exactly linked to the probability of finding zero molecules in a given observation volume. The Gaussian formula for the latter probability is scrutinized to arrive at the enthalpy and entropy changes associated with cavity creation. The reversible work of cavity creation has a purely entropic origin due to the solvent-excluded volume effect produced by the inaccessibility of a given region of the configurational space. The consequent structural reorganization of liquid molecules leads to exactly compensating enthalpy and entropy changes. These results are in line with those obtained in a direct statistical mechanical study by Lee.

The 5-hydroxymethylfurfural (HMF) is a six-carbon heterocyclic organic compound with two substituents an aldehyde group and an alcohol group. It is formed from saccharides as a result of two reactions: the Maillard reaction and the caramelization of saccharides. It has both a negative and a positive effect on the human body, which makes it, even more, an attractive research object. The objective of the study was to determine HMF content in honey samples available on the Polish market using three varied methods and compare the results obtained. The methodology used included: two spectrophotometric methods (by White and Winkler) and the HMF determination method based on the LC-MS/MS technique developed uniquely for this study. The determined HMF content in all tested honey samples did not exceed the applicable standard. All results are within the scope of the European Council Directive 2001/110/EC of 20 December 2001, i.e. they do not exceed HMF content in honey, which is 40 mg/kg.

The increasing emergence of multidrug resistant (MDR) pathogens causes difficult-to-treat infections, with long-term hospitalizations and high incidence of death, thus representing a global public health problem. To manage MDR bacteria bugs, new antimicrobial strategies are necessary, and their introduction in practice is a daily challenge for scientists in the field. An extensively studied approach to treat MDR infections consists in inducing high levels of reactive oxygen species (ROS) by several methods. Although further clinical investigations are mandatory on the possible toxic effects of ROS to mammalian cells, clinical evaluations are extremely promising, and their topical use to treat infected wounds and ulcers, also in presence of biofilm, is already clinically approved. Biochar (BC) is a carbonaceous material obtained by pyrolysis of different vegetable and animal biomass feedstocks, at 200−1000 °C in limited presence of O2. Recently, it has been demonstrated that BC capability of removing organic and inorganic xenobiotics is mainly due to the presence of persistent free radicals (PFRs), which can activate oxygen, H2O2 or persulfate in the presence or not of transition metals by electron transfer thus generating ROS, which in turn degrade pollutants by advanced oxidation processes (AOPs). In this context, the antibacterial effects of BC containing PFRs have been demonstrated by some authors against Escherichia coli and Staphylococcus aureus, thus giving birth to our idea of the possible use of BC-derived PFRs as a novel method capable of inducing ROS generation for antimicrobial oxidative therapy. Here, the general aspects concerning ROS physiological and pathological production and regulation, and the mechanism by which they could exert antimicrobial effects have been reviewed. The methods currently adopted to induce ROS production for antimicrobial oxidative therapy have been discussed. Finally, for the first time, BC-related PFRs have been proposed as a new source of ROS for antimicrobial therapy via AOPs.

Solar radiation is the main energy source for mankind and an accurate data of solar radiation levels for a particular location is vital for the optimum operation of solar energy transducers such as photovoltaic cells and solar thermal collectors. In this work, we show that there is a linear relationship between recorded monthly average temperatures and solar radiation in Swaziland. The correlation can be utilized to develop two mathematical models for the estimation of solar radiation: one from the measured monthly average temperatures and the other based on the square-root of the difference between measured maximum and minimum monthly average temperatures. Both models fit the data well and can be applied to estimate solar radiation in other parts of the region.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with reduced graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorpora-tion of rGO would increase the interlayer spacing of NVO and diminish the charge transfer in-teractions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 95% of its initial specific capacity of 507 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

Despite the effectiveness of insulin injections in managing hyperglycemia in Type 1 Diabetes, they fall short in addressing autoimmunity and regenerating damaged islets. This review aims to explore the potential of various treatment modalities for T1DM, including mesenchymal stem cells (MSCs), MSC-derived exosomes, gene therapy, islet allotransplantation, and pancreatic islet cell transplantation. Results: MSCs demonstrate efficacy in T1DM treatment through immunomodulation and tissue regeneration, although further research is warranted to optimize their therapeutic potential. Gene therapy presents a promising approach despite challenges such as donor shortage and immune rejection. Pancreatic islet cell transplantation emerges as a viable option, albeit with associated risks including graft rejection and the need for immunosuppression. Teplizumab, an FDA-approved humanized monoclonal antibody, revolutionizes the treatment landscape of Type 1 Diabetes by significantly delaying its onset, offering a paradigm shift since the discovery of insulin Conclusion: Ongoing studies and technological advancements in T1DM management offer a promising outlook for improved treatments and possibly even eradication on a global scale. MSCs, MSC-derived exosomes, gene therapy, and pancreatic islet transplantation hold considerable potential.

This article aims to analyze household energy data to predict electricity self-sufficiency and identify the key features that impact it. For this purpose, we use SHAP (Shapley Additive Explanations), LightGBM (Light Gradient Boosting Machine), and a correlation heatmap-based framework to analyze 12 months of energy and questionnaire survey data collected from over 200 smart houses in Kitakyushu, Japan. We use the SHAP summary plot to identify the impact-wise order of key features influencing the electricity self-sufficiency rate (ESSR). Using SHAP, we demonstrated that key features are; housing types, average monthly electricity bill, floor heating, electric capacity, number of washing and drying machines, fee plans, occupation of household head, total floor area, average monthly gas bill, cooking equipment, etc. Furthermore, we adopted the LightGBM classifier with $\ell^1$ regularization to extract the most significant features and predict the electricity self-sufficiency rate of households. This LightGBM-based model can also predict the electricity self-sufficiency rate of households that did not participate in the questionnaire survey. A heat map is also used to analyze the correlation among household variables. The findings discussed in this article offer valuable insights for energy policymakers to achieve the targets of energy self-sufficient houses.

Paratuberculosis, or Johne's disease, caused by Mycobacterium avium subsp. paratuberculosis (MAP), is a chronic granulomatous enteritis affecting both domestic and wild ruminants. The agent was also found in wild mammals such as wild boar (Sus scrofa), however, the role of wild mammals in the epidemiology of MAP is unclear. During the research period, 941 free-ranging wild boar (S. scrofa) legally hunted in two locations in the Centre-eastern region of Portugal were examined. Ninety-seven wild boar exhibited one or more gross lesions and were tested for the presence of Mycobacterium avium subsp. paratuberculosis using acid-fast staining, mycobacterial culture, poly-merase chain reaction (PCR), and histopathological examination. Forty-five animals (46.4%, 95% CI: 36.5-56.3%) were identified as infected, as indicated by positive results in culture and/or PCR. The findings revealed that the most significant risk factor was being a juvenile compared to year-lings and adults (OR = 10.2, 95% CI: 2.2-48.0). Based on our results, 37.9% (n = 11) of the infected animals were considered suitable for human consumption. Our findings offer novel insights into mycobacterial infections in wild boar populations in Portugal and suggest that wild boar could be a source of human infection if zoonotic potential is considered.

The reactivity of 3,5-di-(pyridin-4-yl)-1,2,4-thiadiazole (L1) with 1,4-diiodotetrafluorobenzene (1,4-DITFB) was explored and the halogen-bonded 1:1 co-crystal (1) was successfully isolated and structurally characterized.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

The importance of contact with nature for human health was confirmed by numerous research. One of the sometimes neglected fields is the landscape design of hospital premises. This study focuses on the perception and preferences of prospective patients regarding the hospital site design. The methodology included anonymous survey with images and lists of adjectives. The online questionnaire was distributed using e-mails and social media from 4th May to 8th July 2024. The objective was to include all age groups. The results confirm previous studies and demonstrate the importance of landscape architecture design of hospital premises for the well-being of patients. The findings may inform the design of hospital sites.

Postprandial glucose levels between 4 and 7.9 hours (PPG4–7.9h) correlate with mortality from various diseases including hypertension, diabetes, cardiovascular disease, and cancer. This study aimed to assess if predicted PPG4–7.9h could diagnose diabetes. Two groups of participants were involved: Group 1 (4420 participants) had actual PPG4–7.9h, while Group 2 (8422 participants) lacked this measure but had all the diabetes diagnostic measures. Group 1 underwent multiple linear regression to predict PPG4–7.9h using 30 predictors, achieving accuracy within 11.1 mg/dL in 80% of the participants. Group 2 had PPG4–7.9h predicted using this model. Receiver operating characteristic curve analysis showed that predicted PPG4–7.9h could diagnose diabetes with an accuracy of 87.3% in Group 2, with a sensitivity of 75.1% and specificity of 84.1% at the optimal cutoff of 102.5 mg/dL. Simulation on 10,000 random samples from Group 2 revealed that 175 participants may be needed to investigate PPG4–7.9h as a diabetes diagnostic marker with a power of at least 80%. In conclusion, predicted PPG4–7.9h appears to be a promising diagnostic indicator for diabetes. Future studies seeking to ascertain its definitive diagnostic value might require a minimum sample size of 175 participants.

The graphene based highly conductive and flexible devices has received momentous attraction and growth in recent years for potential multifunctional uses. The development of flexible and washable textile sensors, actuators, energy storage and energy harvesting systems. Textile fabrics coated with graphene and conductive polymers have been used for wearable self-powered e-textiles, such as tribo-electric, piezoelectric, and Thermoelectric. Herein this research, 100% woven cotton fabric is Fictionalized with graphene oxide (GO) using industrial-scale cold pad batch dyeing technique for the development of low-grade body heat into self-powered wearable e-textiles. The conductive polymer PEDOT: PSS was coated using layer by layer approach. The study demonstrates that the resultant textile electrodes showed reduced electrical sheet resistance from 2.5 MΩ to 15KΩ, with a reduced graphene oxide and further reduced to (2.5 -12.5 Ω) for conductive polymer. The sheet resistance was decreased with the number of dyeing cycles (10-15) and increased with 20 washing cycles vice versa. The study demonstrates that the sensor response and performance were improved with increasing the content percent of rGO and PEDOT: PSS. The tensile strength of as coated fabric electrodes was improved from (25.0-85.5 mPa) and fabric thickness was increased to (26-38µm) without compromising or influencing the air permeability. The resultant textile electrodes may potentially be used in smart textiles for self-powered flexible wearable generators, sensors, and energy storage. The study demonstrates that the cold pad batch dyeing method is a suitable and effective method for the fabrication of graphene-based textiles.

The transient vanilloid receptor potential type 1 (TRPV1) regulates neuronal and vascular functions mediated by nitric oxide (NO) and by the calcitonin gene-related peptide (CGRP). Here we study the participation of TRPV1 in the regulation of myocardial injury caused by ischemia-reperfusion and in the regulation of NO, tetrahydrobiopterin (BH4), the cGMP pathway, CGRP, total antioxidant capacity (TAC), malondialdehyde (MDA) and phosphodiesterase-3 (PDE-3). Isolated hearts of Wistar rats were used (according to Langendorff) to study the effects of capsaicin (CS), capsazepine (CZ) and CZ+CS treatments. The hearts were divided into three subgroups; 1) perfusion, 2) ischemia and 3) ischemia-reperfusion. In all groups we studied cardiac work and levels of NO, cGMP, BH4, CGRP, TAC, MDA and PDE-3 in ventricular tissue. Western blots were used to determine the expressions of eNOS, iNOS and phosphorylated NOS (pNOS). Structural changes were determined by histological evaluation. CS prevented damage caused by ischemia-reperfusion by improving cardiac work and the levels of NO, cGMP, BH4, TAC and CGRP. TRPV1 and iNOS expression were increased under ischemic conditions, while eNOS and pNOS were not modified. We conclude that the activation of TRPV1 constitutes a therapeutic possibility to counteract the damage caused by ischemia and reperfusion by regulating the NO pathway through CGRP.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

This study explores the enhancement of aqueous zinc-ion batteries (AZIBs) using ammonium-enhanced vanadium oxide cathodes. Density Functional Theory (DFT) calculations reveal that NH₄⁺ incorporation into V₆O₁₆ lattices significantly facilitates Zn²⁺ ion diffusion by reducing electrostatic interactions, acting as a structural lubricant. Subsequent experimental validation using (NH₄)₂V₆O₁₆ cathodes synthesized via a hydrothermal method corroborates the DFT findings, demonstrating remarkable electrochemical stability with a capacity retention of 90% after 2000 cycles at 5 A g⁻¹. These results underscore the potential of NH₄⁺ in improving the performance and longevity of AZIBs, providing a pathway for sustainable energy storage solutions.

Hu7691 represents a novel Pan-Akt kinase inhibitor, demonstrating excellent selectivity towards non-AGC kinase families and pronounced inhibitory effects on the proliferation of multiple tumor cell lines. However, there is currently a notable absence of in vivo toxicological research evidence concerning Hu7691. This study represents the first investigation into the 14-day repeated dose toxicity of Hu7691 in male and female Sprague-Dawley (SD) rats. Male rats were administered daily doses of 12.5, 50, 100, and 150 mg/kg, while female rats received doses of 12.5, 25, 50, and 75 mg/kg for 14 consecutive days. Hematological assessments, organ weights, and histopathological examinations revealed corresponding alterations, suggesting potential target organs for toxicity including the spleen, thymus, and gastrointestinal tract. It is worth noting that the test substance may also impact the liver, kidneys, heart, and ovaries. The No Observed Effect Level (NOAEL) was determined to be no greater than 12.5 mg/kg. Based on the observed gender-related toxicity differences in preliminary trials, it is recommended that the high dose reference dose for male animals in formal experiments should not be less than 100 mg/kg, while for female animals, it should be less than 50 mg/kg.

Synergistic effects between reactions, reagents and catalysts can lead to minor heats of reaction and occur as an inherent result of multi-component reactions (MCRs) and their extensions. They enable syntheses to be performed at a low energy level and the number of synthesis steps to be drastically reduced in comparison with ‘classical’ two-component reactions. The very high potential for variability, diversity and complexity of MCRs additionally generates an extremely diverse range of products, thus bringing us closer to the aim of being able to produce tailor-made and extremely low-priced materials, drugs and libraries.

Analysis of liquid biopsy samples can reveal a wealth of molecular as well as cellular entities circulating in various body fluids. These entities include circulating tumor cells, circulating cell-free and tumor DNA, RNA, and proteins. Detection and characterization of this genetic and proteomic material can provide crucial information on tumor characteristics, including its heterogeneity, biology, tumor progression, staging, associated gene mutations and the course of therapy. The increased use of liquid biopsy in clinical oncology offers in non-invasive manner easier tumor sampling and continuous monitoring of the disease evolution through repetitive sampling from cancer patients. The continuous monitoring offered by this method is highly relevant to the assessment of a given therapeutic regime and early detection of markers associated with possible drug resistance, which may develop in the course of the therapy. The use of proteomic approaches, including mass spectrometry-based proteomics for the analysis of biofluids extends for over three decades, yet only in the last few years such methods have found their way to clinical oncology. The non-invasive nature of liquid biopsy and the simple procedures for sample collection made this approach far more attractive than the traditional and well-established tissue biopsy. Such preference becomes more practical in the analysis of solid tumors, particularly in pediatric population. In this review we discuss some works on the emerging role of liquid biopsy analyses in clinical oncology, and how such use allows a better understanding of diagnosis, prognosis, disease evolution and response to therapy of various forms of cancer. We also discuss the role of MS-based methods in the characterization of post-translational modifications of proteins circulating in liquid biopsies.

This article has been studied the synthesis of a new derivative of the known alkaloid cytisine contained in the seeds of plants of Cytisus laburnum L. and Thermopsis lanceolata R.Br., both of the Lugiminosae family. The new compound has been obtained from two biologically active compounds such as isoxazole and cytisine. It has been demonstrated that the reaction led to the single-stage method under very mild conditions to obtain some 4-[(3,5-dimethyl-1,2-oxazole-4-yl)sulfonyl]amides. This class of compounds is promising to obtain the new biologically active compounds. This article has examined in detail a structure with using the 1H and 13C NMR and two-dimensional NMR spectroscopy of COSY (1H-1H), HMQC (1H-13C) and NMVS (1H-13C). As a result, the homo- and heteronuclear spin-spin couplings should be established. The X-ray diffraction analysis has determined the spatial structure of a new derivative based on cytisine alkaloid. Thus, its hemorheological activity has been studied.

Stage IV grade C localized periodontitis (pre-puberal localized aggressive periodontitis/LPP), an extremely rare form of periodontal disease, occurs in otherwise healthy individuals (no signs of dental plaque/calculus) due a hyper-aggressive auto-immune response to high periodontopathic bacteria levels. Methods: A 4-year-old Caucasian girl with unusual high mobility of temporary lower left canine and localized gingival inflammation was misrecognized by multiple clinicians (initially diagnosed with hypophosphatasia, genetic and metabolic disorders, all turning negative), over a period of 4-6 month, despite initial radiographs showing clear pathognomonic signs. LPP diagnostic was made by the last clinician, but by now the tooth was lost. Similar inflammation signs appeared around the lower temporary right canine. X-ray examination showed similar bone and periodontal loss as previously seen, while periodontopathic bacteria tested highly positive. The patient received both mechanical cleaning and ten days systemic antibiotic treatment (Augmentin and Metronidazole). Results: Two months after, inflammation signs disappeared, with periodontal regeneration radiologically present, and only small periodontopathic bacteria precursors concentrations. Conclusions: Despite initial periodontal loss, an adequate treatment can keep under control an LPP disease. Moreover, bone and periodontal regeneration appears if periodontopathic bacteria scores are kept lower, showing the importance of fast adequate diagnostic and treatment.