MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

The relaxation process of lithium batteries caused by load variation is considered. It is shown that such processes have strong dependence on internal physical and chemical processes and battery technical conditions. Theoretical expressions of the relaxation process caused by a step-like load variation have been obtained for 1^st and 2^nd order equivalent electrical circuits. The experimental investigations show that the obtained models fit the real relaxation processes and the behavior of the identified parameters could be explained by specific features of physical and chemical processes within the lithium battery. It should be noted that the obtained results can be generalized for a different type of electrochemical power source. The proposed approach makes it possible to provide means for electrochemical power source characterization and diagnostic, the main advantages of which are good time localization of measurement procedures and inexpensive apparatus implementation.

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

Chronological frameworks based on artefact typologies are essential for interpreting the archaeological record, but they inadvertently treat transitions between phases as abrupt events and disregard the temporality of transformation processes within and between individual phases. This study presents an absolute chronological investigation of a dynamic material culture from Early Iron Age urnfields in Denmark. The chronological framework of Early Iron Age in Southern Scandinavia is largely unconstrained by absolute dating, primarily due to it coinciding with the so-called ‘Hallstatt calibration plateau’ (c.750 to 400 cal BC), and it is difficult to correlate it with Central European chronologies due to a lack of imported artefacts. This study applies recent methodological advances in radiocarbon dating and Bayesian chronological modelling, specifically a statistical model for wood-age offsets in cremated bone and presents the first large-scale radiocarbon investigation of regional material culture from Early Iron Age in Southern Jutland, Denmark. Dated material is primarily cremated bone from 111 cremation burials from three urnfields. The study presents absolute date ranges for 16 types of pottery and 15 types of metalwork, which include most of the recognised metalwork types from the period. This provides new insights into gradual change in material culture, when certain artefact types were in production and primary use, how quickly types were taken up and later abandoned, and distinguishing periods of faster and slower change. The study also provides the first absolute chronology for the period, enabling correlation with chronologies from other regions. Urnfields were introduced at the Bronze-Iron Age transformation, which is often assumed to have occurred c.530-500 BC. We demonstrate that this transformation took place in the 7^th century BC, however, which revives the discussion of whether the final Bronze Age period VI should be interpreted as a transitional phase to the Iron Age.

The absolute time and relative time are defined in terms of the 4-D Euclidean space. Our universe is the 3-D x₁x₂x₃ quantized photon space which follows the absolute time simultaneity when the universe moves along the absolute time axis of ct. The length expansion of Dx = gDx₀ is derived under the condition of the absolute time (ct) simultaneity. From the similarity between this length expansion of Dx = gDx₀ and the energy increasing of E = gE₀, it is assumed that the energy is proportional to the particle size of Dx. The extension of this assumption to the 4-D Euclidean space gives the new definition that the particle energy (E) is the 4-D volume. Then, the particle mass energy is defined as E= mc² = cDtDV = gE₀. The masses of the elementary particles are originated from the 4-D warped volume of the photon space because the particle is the warped photon space with the velocity of v < c. Therefore, the Higgs boson concept in the standard model (SM) is not needed in the present 3-D quantized space model (TQSM). The scalar boson with the spin of zero, photon with the spin of 1 and graviton with the spin of 2 are the two-boson states. Therefore, the observed Higgs boson is reinterpreted as the two-boson state of the scalar boson with the spin of zero. The cosmic muon observation and twin paradox are explained by using the absolute time and relative time. The relative time is the observed time in the twin paradox and cosmic muon observation. In the twin paradox, a person who travels the long distance is more aged than a person on the earth in terms of the relative time ages because of the space and time conversion effect (STCE effect) of the moving space distance (x). But twins are in the same ages in terms of the absolute time without STCE effect. The fast-moving cosmic muon has the expanded half-life from the time expansion of the relative time. Also, the quantum entanglement and Pauli exclusion principle are explained. The quantum base of the photon space line connects two entangled particles. Two particles and quantum base system is fluctuated along the absolute time axis by the time clicking when one particle is measured. Another particle is instantly selected by the time clicking. This is called as the quantum entanglement. The photons which are the flat photon space with the constant speed of c along the space axis and absolute time axis have the 4-D photon velocity of c_eff = 2^0.5 c. Total 10-D Euclidean space including three 3-D quantized spaces and one absolute time axis is required for the electric charges (EC), lepton charges (CC) and color charges (CC) of the elementary particles. The 3-D photon space is very stiff along the absolute time (ct) axis and very soft along the space axes. The Coulomb force through the photons (2EM waves) of the space fluctuations is much stronger than the Gravitational force through the gravitons (G waves) of the time fluctuations between two electrons.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

In 1922, Albert Einstein visited Paris and interacted extensively with an illustrious section of the French academia. In overfilled sessions at the Coll\`{e}ge de France and the Sorbonne, Einstein explained his theories of relativity, and prominent physicists, mathematicians and philosophers listened, debated, questioned and explored facets of relativity. The 1922 visit had its echoes in the life and works of many who participated, particularly decisive for Einstein and the philosopher Henri Bergson. This essay examines that eventful visit, focusing on the physical and logical aspects of Bergson's critique, with physics commentaries, linking prominent French physicists and mathematicians Langevin, Painlev\'{e}, Hadamard, Becquerel, Sagnac, and Kastler. I give particular attention to the logical and empirical accuracy of the physics issues involved, delineating Bergson's exact reasoning for his philosophical enthusiasm in Einstein's theory and for the ensuing critique. Bergson's philosophical stand on duration and simultaneity is reassessed in the context of later developments in cosmological physics as well as the wealth of empirical data involving comparison of atomic clocks. Finally we are led naturally to a surprising completion of the philosopher's program on universal time, duration and simultaneity, in harmony with the time of the physicist. In the appendices after the main text I also give the physics background and easily verifiable proofs for the assertions made in the text, pertaining to relativity, simultaneity and time dilation, clearly distinguishing beliefs and facts.

The paper suggests that the physical priciple of special relativity's space-time transformation effect is wrong, Uniform linear motion without acceleration does not exist objectively, nor does its same reference frames. Therefore, it is inferred that the space-time transformation effect of special relativity is caused by the acceleration of moving objects, special relativity is only a part of general relativity, not a theoretical system that exists independently from general relativity. The corresponding mathematical demonstration and calculation verification are carried out, and the result proves that the inference of the paper is correct. At the same time, it further explains that the concept of absolute airspace is correct. Special relativity has serious errors in the concept of space, the principle of relativity and the physical principle of space-time transformation effect. Therefore, it is necessary to make a series of revisions to the theory of relativity and to reinterpret some related physical problems.

Sharding shows great potential for extending the blockchain. The current challenge facing sharded blockchain technology lies in addressing the extended transaction confirmation times caused by isolated states between shards and unbalanced transaction allocation strategies. These factors contribute to an increase in cross-shard transactions and disproportionate shard workload, ultimately resulting in indefinite confirmation delays for cross-shard transactions. A critical priority for sharded blockchain systems is to conduct a comprehensive qualitative analysis to better understand and mitigate the prolonged transaction confirmation times. We introduce a Product-Form Queue Network (PFQN) model to address the transaction confirmation time problem in sharded blockchains and incorporate a new confirmation queue to more accurately simulate the actual transaction confirmation process in the blockchain. In addition, we provide a detailed quantitative analysis of the relationship between network load, consensus efficiency, and security in sharded blockchains, laying a theoretical foundation for achieving robustness and efficiency in sharded blockchains. This research not only contributes to addressing the scalability issues in sharded blockchains but also offers a new perspective for future research directions.

In this paper, the problem of autonomous optimal absolute orbit keeping for a satellite mission in Low Earth Orbit using electric propulsion is considered. The main peculiarity of the approach is to support small satellite missions in which the platform is equipped with a single thruster nozzle which provides acceleration on a single direction at a time. This constraint implies that an attitude maneuver is necessary before or during each thrusting arc to direct the nozzle into the desired direction. In this context, an attitude guidance algorithm specific for the orbit maneuver has been developed. A Model Predictive Control scheme is proposed, where the attitude kinematics are coupled with the orbital dynamics in order to obtain the optimal guidance profiles in terms of satellite state, reference attitude, and thrust magnitude. The proposed control scheme is developed exploiting Formation Flying techniques where the reference orbit is that of a virtual spacecraft that the main satellite is required to rendezvous with. In addition to the controller design, the closed loop configuration is presented supported by numerical simulations. The efficacy of the proposed autonomous orbit keeping approach is shown in several application scenarios.

The purpose of this article is to characterize the Caristi type mapping by the absolute derivative. The equivalences of the Caristi mapping with contraction mapping is discussed too. In addition, it was shown that the contraction mapping can be characterized by its absolute derivative.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

This paper is mainly based on a stricter premise of the twin paradox and the assumption of inertial frame, discusses the properties of time and space under the premise of complete symmetry, and draws an interesting conclusion: the simultaneity of different reference frames is possible realized, and the space is relatively independent. And based on this, the twin paradox, cosmic inflation, ultra-distance action of quantum entanglement, microscopic space motion of particles, measurement problems and other phenomena are tentatively explained from a new angle. This interpretation is exploratory and new. At the same time, the author also proposes an experimental way to test the relative independence of space.At the same time, this paper attempts to strictly prove that Einstein's definition of simultaneity and spatial absoluteness in special relativity may be problematic.

From the aerial parts of Salvia ballotiflora, eleven diterpenoids were isolated, among them, four icetexanes, and one abietane (1–5), which are first reported. Their structures were established by spectroscopic means, mainly ¹H and ¹³C NMR, including 1D and 2D homo- and hetero-nuclear experiments. Most of the isolated diterpenoids were tested for their antiproliferative, anti-inflammatory, and radical scavenging activities using the sulforhodamine B assay on six cancer cell lines, the TPA induced ear edema test in mice, and the reduction of the DPPH assay, respectively. Some diterpenoids showed anti-proliferative activity, these being icetexanes 6 and 3, which were the most active with IC₅₀ (µM) = 0.27 ± 0.08 and 1.40 ± 0.03, respectively, for U251 (human glioblastoma) and IC₅₀ (µM) = 0.0.46 ± 0.05, and 0.82 ± 0.06 for SKLU-1 (human lung adenocarcinoma), when compared with adriamycin (IC₅₀ (µM) = 0.08 ± 0.003, and 0.05 ± 0.003, as the positive control, respectively. Compounds 3 and 10 showed significant reduction of the induced ear edema of 37.4 ± 2.8 and 25.4 ± 3.0% (at 1.0 µmol/ear), respectively. Compound 4 was the sole active diterpenoid in the antioxidant assay (IC₅₀ = 98. 4 ± 3.3), using α-tocopherol as positive control, IC₅₀ (µM) = 31.7 ± 1.04. The diterpenoid profile found is of chemotaxonomic relevance and reinforces the evolutionary link of S. ballotiflora with other members of the section Tomentellae.

Biothermodynamics of viruses is among the youngest, but rapidly developing scientific disciplines. During the COVID-19 pandemic, it has closely followed the results published by molecular biologists. Empirical formulas were published for 50 viruses and thermodynamic properties for multiple viruses and virus variants, including all variants of concern of SARS-CoV-2, SARS-CoV, MERS-COV, Ebola virus, Vaccinia and Monkeypox virus. A review of development of biothermodynamics of viruses during the last several decades and intense development during the last 3 years has been described in this paper.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

Quantum gravity theories rely on a minimal measurable length for their formulations, which clashes with the classical formulation of the uncertainty principle and with Lorentz invariance from general relativity. These incompatibilities led to the development of the generalized uncertainty principle (GUP) from string theories and its various modifications. GUP and covariant formulations of the uncertainty principle are discussed, together with implications for space-time quantization.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

Abscisic acid (ABA) plays a major role in promoting ripening in sweet cherry, a non-climateric fruit. Exogenous application of ABA has been performed to study fruit ripening and cracking, but this growth regulator is not used for commercial production. To determine the potential of this growth regulator to improve sweet cherry fruit quality, ABA canopy spraying was assayed in four cultivars. Canopy spraying of S-ABA significantly: 1) enhanced sweet cherry fruit color in ‘Glenred’, ‘Lapins’ and 'Bing' cultivars, but not in ‘Royal Rainier’ (a bi-colored cultivar), and 2) decreased fruit size and firmness in ‘Lapins’, ‘Bing’ and ‘Royal Rainier’. Seasonally reproducible effects were seen in ‘Lapins’ (mid/late-maturing) but not in ‘Glenred’ (early-maturing). Canopy spraying of nordihydroguaiaretic acid (NDGA) decreased color and increased fruit size in ‘Lapins’, but not in ‘Glenred’. Direct application of ABA on fruits attached to the tree, without application to the foliage, increased Lapins' fruit color without reducing size. These results suggest a localized fruit response to exogenous ABA application on fruit color development, but that a decrease in fruit size may be due to the effects of exogenous ABA on the tree canopy foliage.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Optimal control is a critical tool for mechanical robotic systems, facilitating precise manipulation of dynamic processes. These processes are described through differential equations governed by a control function, addressing a time-optimal problem with bilinear characteristics. Our study utilizes the classical approach complemented by Pontryagin's Maximum Principle (PMP) to explore this inverse optimal problem. The objective is to develop an exact piecewise control function that effectively manages trajectory control while considering the effects of viscous friction. Our simulations demonstrate that the proposed control law markedly diminishes oscillations induced by boundary conditions. This research not only aims to delineate the reachability set but also strives to determine the minimal time required for the process. The findings include an exact analytical solution for the stated control problem.

In this paper, a proof similar to the Pusey-Barrett-Rudolph (PBR) theorem is given to prove that time in quantum theory is not epistemic but has ontological reality. For this, we first discuss how time can be encoded as an intrinsic property of a quantum system. We prepare a quantum state containing time as an intrinsic property and show by a PBR-type proof that time cannot be an epistemic notion. In fact, the PBR theorem implies an ontic notion of time. Indeed, if the quantum state is a physical property, then quantum state reduction is a physical process involving information destruction. In this case, quantum probabilities are intrinsic probabilities without epistemic origin, and they generate a genuinely new sequence of events. This novelty introduced by quantum probabilities can be interpreted as time.

Recently, polyacetylene (PA) is receiving a renewed scientific attention because of its unique properties potentially useful also for non-electrical applications (e.g., hydrogen storage, drug delivery, adsorbent of organic compounds in aqueous systems, gas and liquid separation, oxygen absorbent in gas analysis, etc.). Poly(vinyl alcohol) (PVOH) is a very common type of polymer, widely exploited in different technological areas, and it can be used as a precursor for the PA synthesis. Here, a new scheme for a large-scale chemical synthesis of PA, based on a simple and low-cost PVOH dehydration reaction by absolute sulfuric acid, has been developed. In this process, PVOH, shaped in form of film, is dipped in absolute sulfuric acid (i.e., H₂SO₄ at 95-97%) and, after complete chemical-dehydration at room temperature, it is mechanically removed from the liquid phase by using a plastic sieve. This reaction leads to a complete PVOH film conversion to PA as it has been proved by infrared spectroscopy (ATR-mode). Indeed, the ATR spectrum of the reaction product included all characteristic absorption bands of PA. To the best of our knowledge, this very easy and effective PA synthesis method based on the PVOH chemical-dehydration reaction by absolute sulfuric acid has never been described in the literature.

It is proven that the Clapeyron-Mendeleev equation, originally discovered for gases with large entropy, describes the state of dark matter and energy due to enormous self-gravitation. It is shown that the dark matter exists as compact cold neutrino stars at positive temperature with size twice the Schwarzschild radius. In contrast, the dark energy is dark matter at temperature below the absolute zero, which is locked entirely in black holes, where the pressure is negative as required for the Universe intrinsic expansion. The derived dark phase diagram predicts negative critical temperatures for the Big Bang and the Big Rip of black holes.

In this study, we discuss the properties of absolute vacuum space and how these properties can play a vital role in creating a mechanism in which the very first particle gets created simultaneously everywhere and we find the limit in which when the absolute vacuum volume reaches will lead to the collapse that leads to the creation of the first particle. This discussion is made following to the elementary dimensions theory study that was peer-reviewed at the end of 2020, everything in the universe is made from four elementary dimensions, these dimensions are the three spatial dimensions (X, Y, and Z) and the Vacuum resistant as the factor of change among the four, time itself wasn’t considered as the fourth dimension, rather time corresponds to a factor of change, and during the research it was found out that the Vacuum resistant is the factor of change in the Absolute Vacuum space, where time is a hypothetical concept, that represents changes during certain events compared to a constant change rate event.Therefore, time does exist, but as a factor of change, and as the Vacuum resistant in the absolute vacuum space, Time= factor of change= Vacuum resistant. In the study, the internal and external vacuum resistant volume equivalent is found, External Vacuum resistant=3.2857602*10^15 *mass. This equation is used to identify the amount of Free external vacuum resistant created during nuclear fission and fusion: Initial mass of the excited nucleuses mass of the created new nucleuses+ 3.2857602*10^15 * the lost Mass. In elementary dimensions, the energy created during nuclear reactions is equivalent to the free External vacuum resistant created through nuclear reactions, and mass is equivalent to the internal Vacuum resistant.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

This work introduces a new architecture for a time-domain feedback-based beamformer designed to meet real-time processing demands. The primary goal of this design is to locate reflective sources by estimating their direction of arrival (DOA) and signal range. Incorporating a feedback mechanism in this architecture is a unique aspect that refines localization precision. We conduct an in-depth analysis highlighting their respective benefits and limitations to compare the effectiveness of time-domain feedback beamforming against conventional time-domain methods. Our evaluation of the proposed architecture, based on critical performance indicators such as peak-to-sidelobe ratio, mainlobe width, and directivity factor, demonstrates its ability to improve beamformer effectiveness significantly.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

Abstract: Nordic exercises aim to improve physical abilities and prevent injuries; However, it is not clear in what type of sports modalities to use it, so this study arises from the interest of ana-lyzing its effect in different sports modalities. Objective: To analyze Nordic exercises effects on the lower limbs, and their relationship with the explosive and absolute strength inherent to demands of different sports modalities (football, athletics, basketball, sport climbing, cycling and taekwondo). Method: quasi-experimental research, identifying 122 athletes (18±3 years old) from: football (n=24), athletics/speed (n=20), sport climbing (n=20), basketball (n=24), taekwondo (n=14) and cycling (n=20); classified into a control group CG (n=57) and an experimental group EG (n=65). Results: dominant absolute strength of the initial (12.4±0.51) and final (14.5±0.98) EG, in greater proportion in basketball (P= < 0.05); explosive strength of the initial (42.4±1.2) and final (45.8±1.5) EG, with a significant difference in all modalities between before and after (p≤0.05), except in cy-cling and taekwondo; no major changes were found in the GC. Conclusion: Nordic exercises are recommended as part of training to improve levels of explosive strength with emphasis on the modalities of football, basketball, athletics/speed and sport climbing, being applicable to increase absolute strength in basketball.

Background: Recent advances allow the usage of Augmented Reality (AR) for many medical procedures. We perform different AR-assisted knee surgery techniques using optical surgical navigation with ArUco-type artificial marker sensors. Our study aimed to evaluate the system’s accuracy using an in vitro protocol. We hypothesised that the system’s accuracy was equal to or less than 1mm and 1° for distance and angular measurements, respectively. Methods: Our research was an in-vitro laboratory with a 316 L steel model. We evaluated absolute reliability according to the Hopkins criteria with seven independent evaluators. Each observer measured the thirty palpation points and the trademarks to acquire direct angular measurements on three occasions separated by at least two weeks. Results: The accuracy of the system to assess distances had a mean error of 1.203mm and an un-certainty of 2.062, and for the angular values, a mean error of 0.778° and an uncertainty of 1.438. The intraclass correlation coefficient was for all intra-observer and inter-observer almost perfect or perfect. Conclusions: The mean error for the distance’s determination has been statistically larger than 1mm (1.203mm) but with a trivial effect size. The mean error assessing angular values was sta-tistically minor than 1°. Our results are similar to those published by other authors in accuracy analyses of AR systems.

We review time expansion wave theory and refine our model showing it to accurately match observed cosmological luminosity data. The theory augments general relativity to create a container within which quantum effects can be explained by treating time as an artefact of a fourth spatial dimension that we observe as the expansion of the universe. This leads us to explain mass creation, the speed of light limit, gravity, black holes without singularities and other macroscopic effects. Our model leads to an expansion velocity of 6.87 0.36 × 106 ms-1, which results in a Hubble expansion rate constant of 71.3 3.7 km/s/Mpc. Because of the finite window of time in which we exist, an extra a degree of freedom is available leading to interesting interpretations at the subatomic level. At this size range, then a spin is allowed within the time dimension explaining why wave particle duality occurs and explains the electromagnetic force and other quantum mechanical properties. It provides a solution to the double slit conundrum and can explain how quantum entangled partners can behave in a quantum way and pass seemingly time-defying information. The potential quantitative origin of the fine structure constant which governs the size of the electromagnetic force is also strongly indicated by this theory.

The variable-length arbitrary Lagrange-Euler (ALE)-ANCF finite element, which employ nonrational interpolating polynomials, cannot exactly describe the rational cubic Bezier curves such as conic and circular curves. The rational absolute nodal coordinate formulation (RANCF) finite element, whose reference length (undeformed length) is constant, can exactly represent the rational cubic Bezier curves. A new variable-length finite element called the ALE-RANCF finite element, which is capable of accurately describe the rational cubic Bezier curves, is proposed by combining the desirable features of the ALE-ANCF and RANCF finite element. In order to control the reference length of ALE-RANCF element within a suitable range, element segmentation and merging schemes are proposed. It is demonstrated that exact geometry and mechanic is maintained after the ALE-RANCF element is divided into two shorter ones, and compared with the ALE-ANCF elements, there are smaller deviations and oscillations after two ALE-RANCF elements are merged into a longer one. Numerical examples are presented and the feasibility and advantages of the ALE-RANCF finite element are demonstrated.

In this paper, we study the asymptotic behavior of the sequential empirical process and the sequential empirical copula process, both constructed from residuals of multivariate stochastic volatility models. Applications for the detection of structural changes and specification tests of the distribution of innovations are discussed. It is also shown that if the stochastic volatility matrices are diagonal, which is the case if the univariate time series are estimated separately instead of being jointly estimated, then the empirical copula process behaves as if the innovations were observed; a remarkable property. As a by-product, one also obtains the asymptotic behavior of rank-based measures of dependence applied to residuals of these time series models.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

This paper investigates the feasibility of a backend design for real-time, multiple-channel processing digital phased array system, particularly for high-performance embedded computing platforms constructed of using general purpose digital signal processors. Frist, we obtained the lab-scale backend performance benchmark from simulating beamforming, pulse compression, and Doppler filtering based on MicroTCA chassis using Serial RapidIO protocol in backplane communication. Next, a field-scale demonstrator of a multifunctional phased array radar is emulated by using the similar configuration. Interestingly, the performance of a barebone design is compared to that of emerging tools that systematically take advantage of parallelism and multicore capabilities, including Open Computing Language.

In this paper, the concept of absolute airspace is further elaborated, and the time transform effect, the frequency transform relation of clock timing, and the principle of Doppler effect of special relativistic light are analyzed and demonstrated. Based on the concept of absolute airspace, a new and accurate Doppler effect relation of light (electromagnetic wave) is proposed. It is proved that there is a synchronous relationship between the time shift effect and the frequency change of the timing inside the clock. When the light (electromagnetic wave) source is in motion, the Doppler effect includes two physical mechanisms: the frequency change caused by time transformation effect and the frequency change caused by relative motion. When the light source is in motion, the Doppler effect of the light there are some differences in different directions due to the rotation of the earth. The relation of Doppler effect of special relativistic light is only a highly approximate relation, and its theoretical basis, special relativity, is flawed in principle.

In proteomics, it is essential to quantify proteins in absolute terms if we wish compare results among studies and integrate high-throughput biological data into genome-scale metabolic models. While labeling target peptides with stable isotopes allows protein abundance to be accurately quantified, the utility of this technique is constrained by the low number of quantifiable proteins that it yields. Recently, label-free shotgun proteomics has become the “gold standard” for carrying out global assessments of biological samples containing thousands of proteins. However, this tool must be further improved if we wish to accurately quantify absolute levels of proteins. Here, we used different label-free quantification techniques to estimate absolute protein abundance in the model yeast Saccharomyces cerevisiae. More specifically, we evaluated the performance of seven different quantification methods, based either on spectral counting (SC) or extracted-ion chromatogram (XIC), which were applied to samples from five different proteome backgrounds. We also compared the accuracy and reproducibility of two strategies for transforming relative abundance into absolute abundance: a UPS2-based strategy and the total protein approach (TPA). This study mentions technical challenges related to UPS2 use and proposes ways of addressing them, including utilizing a smaller, more highly optimized amount of UPS2. Overall, three SC-based methods (PAI, SAF, and NSAF) yielded the best results because they struck a good balance between experimental performance and protein quantification.

A linear stability analysis of the parallel uniform flow in a horizontal channel with open upper boundary is carried out. The lower boundary is considered as an impermeable isothermal wall, while the open upper boundary is subject to a uniform heat flux and it is exposed to an external horizontal fluid stream driving the flow. An eigenvalue problem is obtained for the two-dimensional transverse modes of perturbation. The study of the analytical dispersion relation leads to the conditions for the onset of convective instability as well as to the determination of the parametric threshold for the transition to absolute instability. The results are generalised to the case of three-dimensional perturbations.

Obesity poses significant challenges in rural communities worldwide due to limited resources and healthcare access. Practical, innovative, and culturally sensitive approaches are essential. Time-Restricted Eating (TRE), aligning food intake with circadian rhythms, emerges as a promising strategy. By restricting eating to specific time windows, TRE synchronizes with the body's internal clock, offering potential metabolic health benefits. This review examines TRE's potential in rural obesity management, highlighting its simplicity and scalability. While TRE may address rural health disparities, cultural considerations and challenges such as undernutrition must be acknowledged for effective implementation. Overall, TRE shows promise in improving metabolic health and well-being in rural populations.

Abstract: Chemical investigation of the leaves from Ageratina glabrata yielded four new thymol derivatives, namely: 10-Benzoyloxy-8,9-dehydro-6-hydroxythymol isobutyrate (4), 10-benzoyloxy-8,9-dehydro thymol (5), 10-benzoyloxythymol (6) and 10-benzoyloxy-6,8-dihydroxy-9-isobutyryloxythymol (7). In addition, (8S)-10-benzoyloxy-8,9-epoxy-6-hydroxythymol isobutyrate (1), together with other two already known thymol derivatives identified as: 10-benzoyloxy-8,9-epoxy-6-methoxythymol isobutyrate (2) and 10-benzoyloxy-8,9-epoxythymol isobutyrate (3). In this paper, we wish to publish the structures and complete assignments of ¹H and ¹³C NMR data of compounds 1 – 7, and the absolute configuration for compound 1, unambiguously established by single crystal X-ray diffraction, and evaluation of the Flack parameter. The in vitro antiprotozoal assay showed that compound 1 and its derivative 1a were the most potent antiamoebic and antigiardial compounds. Both compounds showed selectivity and good antiamoebic activity like emetine and metronidazole, respectively, two antiprotozoal drugs used as positive controls. In relation of anti-propulsive effect, compound 1 and 1a showed moderate inhibitory activity, their activities were comparable to quercetin and compound 9, respectively, two natural antipropulsive compounds used as positive controls. These data suggest that compound 1 may play an important role in antidiarrheal properties of Ageratina glabrata.

The sTetro is a stair cleaning robot which can climb the staircase with its shapeshifting capabilities. As this robot is intended to traverse multi-floor environment autonomously, hence its localization/positioning information is an essential component of the overall system. Usually, the indoor mobile robots rely on some external system for localization information, e.g., WiFi, UWB, vision, RFID signals, or indoor Global Positioning System (GPS). This requires the installation of additional hardware and/or modification of the working environment for precise positioning information of the mobile platform. As the dimensions of the staircase are known a priori, this knowledge can be used to localize the sTetro robot on the stairs. In this article, the geometry of the staircase has been exploited to localize the robot in 3D space with measurements from the onboard time-of-flight (ToF) range sensors only. The heading angle of the robot is also estimated with two ToF sensors installed in front of the sTetro robot. Results achieved by conducting experiments on real robot prove the efficacy of the proposed approach.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

A method of measuring the absolute pose parameters of a moving rigid body using a monocular camera is proposed, aiming at addressing calibration difficulties and inconsistencies of repeated measurements of the rigid-body pose for a camera having a varying focal length. The proposed method does not require calibration beforehand. Using more than six non-coplanar control points symmetrically arranged in the rigid-body and world coordinate systems, the matrices of rotation and translation between the camera and two coordinate systems are obtained and the absolute pose of the rigid body measured. In this paper, formulas of the absolute pose measurement of a moving rigid body are deduced systematically and the complete implementation is presented. Position and attitude measurement experiments carried out on a three-axis precision turntable show that the average absolute error in the attitude angle of a moving rigid body measured by an uncalibrated camera at different positions changes by no more than 0.2 degrees. Analysis of the three-dimensional coordinate errors of the centroid of a moving rigid body shows little deviation in measurements made at three camera positions, with the maximum deviation of the average absolute error being 0.53 cm and the maximum deviation of the standard deviation being 0.66 cm. The proposed method can measure the absolute pose of a rigid body and is insensitive to the position of the camera in the measurement process. This work thus provides guidance for the repeated measurement of the absolute pose of a moving rigid body using a monocular camera.

Background: Patients with thromboembolic disease, prosthetic valves, or coagulation issues are commonly prescribed anticoagulants and antiplatelets. Although common professional oral hygiene might not represent a health concern for these patients, anticoagulant and antiplatelet medication might constitute a challenge for dentists and dental hygienists since possible prolonged bleeding might interfere with dental procedures. The aim of the present study was to investigate the bleeding time of different anticoagulants and antiplatelets during a professional hygiene session adapting the Ivy test to the oral environment; Methods: 93 consecutive patients undergoing professional oral hygiene were recruited. Debridement during oral hygiene was performed using ultrasonic mechanical instrumentation, and bleeding sites were assessed and treated with gentle pressure using sterile gauzes. The time for bleeding cessation was recorded. Patients were categorized into six groups based on their drug intake, Control: no anticoagulants or antiplatelets DTI: direct thrombin inhibitors (dabigatran) AntiXa: directa factor Xa inhibitors (endoxaban, apixaban, rivaroxaban) VKA: vitamin K antagonists (warfarin, acenocoumarol) SAPT: single anti-platelet therapy (acetylsalicylic acid or clopidogrel) DAPT: dual anti-platelet therapy (acetylsalicylic acid and clopidogrel). Bleeding time was measured in seconds and mean values were assessed among the different groups. Differences between groups were investigated with Kruskal-Wallis test followed by Dunn’s post-hoc correction for multiple comparisons or two-way ANOVA followed by Dunnett post-hoc; Results: Control patients presented the lowest bleeding time 50 sec, followed by AntiXa (98), SAPT (105), DTI (120), DAPT (190) and VKA (203). A statistically significant difference was present among control and DTI (p=0.004), VKA (p&lt;0.001), DAPT (p&lt;0.001). Conclusions: Based on the present outcomes, an increased risk of prolonged bleeding emerged in patients taking VKA and DAPT. However, bleeding did not interfere with the oral hygiene ses-sion The optimal period for dental treatment of these patients should be 2-3 hours before the next dose, without the need to temporarily suspend the medication.

Permeability is an important transport property of porous materials, and its accurate evaluation is relevant in studying applied tasks such as CO2 injection into reservoirs and investigating groundwater quality issues. This study examines the dependence of permeability on total and connected porosity, hydraulic tortuosity, specific surface area, and mean pore radius based on the data of 408 cubic sub-volumes extracted from heterogeneous and naturally fractured cylindrical carbonate samples before and after injection of HCl solutions into them. These parameters were computed using pore-scale modeling of fluid flow. It has been shown that permeability correlates well with porosity and mean pore radius with correlation coefficients of R2≈0.65-0.79 for heterogeneous samples. It was found that the presence of natural fractures significantly influenced the relationship between permeability and other parameters. The relationship between permeability k, tortuosity τ, and specific surface area S is described by power laws k~τ-α and k~S-β, with coefficients α and β substantially exceeding those in the Kozeny-Carman equation. It was also found that there is a parabolic relationship between connected and total porosities both before and after rock dissolution with R2≈0.96-0.99. This allowed for estimation of percolation threshold porosity that are in good agreement with the literature data.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

Leishmaniasis is the third most common vector-borne disease and a very important protozoan infection. Cutaneous leishmaniasis is one of the most common types of leishmaniasis infectious diseases with up to 2 million occurrences of new cases each year worldwide. A dynamic transmission multivariate time series model was applied to the data to account for overdispersion and evaluate the effects of three environmental layers as well as seasonality in the data. Furthermore, ecological niche modeling was used to investigate the geographical suitable conditions for cutaneous leishmaniasis using temperature, precipitation and altitude as environmental layers, together with the leishmaniasis presence data. A retrospective analysis of the cutaneous leishmaniasis spatial data in Afghanistan between 2003 and 2009 indicates a steady increase from 2003 to 2007, a small decrease in 2008, then another increase in 2009. An upward trend and regularly repeating patterns of highs and lows was observed related to the months of the year which suggests seasonality effect in the data. Two peaks were observed in the disease occurrence-- January to March and September to December -- which coincide with the cold period. Ecological niche modelling indicates that precipitation has the greatest contribution to the potential distribution of leishmaniasis.

The study of precipitation amount at different time scales constitutes an important issue in climate research and risk assessment. When dealing with daily totals, a frequent but sometimes underestimated problem is at what time the observation day begins. The choice of different starting times may lead to incompatibility between stations and incorrect identification of extreme events. In this work, the problem of temporal misalignment between precipitation datasets characterized by different starting time of the observation day is analyzed. The most widely used adjustment methods (1day and uniform shift) and two methods based on reanalysis (NOAA and ERA5) are evaluated in terms of temporal alignment, precipitation statistics and percentile distributions. As test series, the precipitation amount collected from 9 a.m. local time (09 LT) on the previous day to 09 LT on the target day (9-9 datasets) of the Padua and nearby stations in the period 1993-2022 have been selected. Results show that the reanalysis-based methods, in particular ERA5, outperform the others in temporal alignment, regardless the station. But, for the periods in which reanalysis data are not available, “1day” method, which shifts the daily amount back one calendar day, and “unif” method, which distributes uniformly the daily total from a 2-day moving window surrounding the target date, can be considered valid alternatives. On the other side, concerning the precipitation statistics, the reanalysis-based methods are not the best option, as they increase the precipitation frequency and reduce the mean value over wet days, NOAA much more than ERA5. Nevertheless, the uniform method provides a larger deviation from the original daily series. The use of the series of a station nearby the target one, which is mandatory in case of missing data, gives similar or better results than applying any adjustment method to the 9-9 series. General conclusions can hardly be drawn as they depend on the method and station. For the Padua dataset, the analysis was repeated at monthly and seasonal resolution. In general, the adjustment series show the most relevant changes in the precipitation statistics in summer and less temporal alignment with the original series in summer and autumn, the two seasons mainly affected by heavy rains in Padua. Finally, the percentiles distribution, analyzed for all the methods and stations, indicates that any adjustment method underestimates the percentile values, except ERA5. Only Legnaro, the station most correlated with Padua, gives results like ERA5.

It is one of very important and basic problem in compute vision field that recovering depth information of objects from two-dimensional images. In view of the shortcomings of existing methods of depth estimation, a novel approach based on SIFT (the Scale Invariant Feature Transform) is presented in this paper. The approach can estimate the depths of objects in two images which are captured by an un-calibrated ordinary monocular camera. In this approach, above all, the first image is captured. All of the camera parameters remain unchanged, and the second image is acquired after moving the camera a distance d along the optical axis. Then image segmentation and SIFT feature extraction are implemented on the two images separately, and objects in the images are matched. Lastly, an object depth can be computed by the lengths of a pair of straight line segments. In order to ensure that the best appropriate a pair of straight line segments are chose and reduce the computation, the theory of convex hull and the knowledge of triangle similarity are employed. The experimental results show our approach is effective and practical.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

This paper studies the duration patterns of unemployment spells for immigrants and the determinants of unemployment’s completion into one of a number of studied labour market states in Finland. We estimate a duration model for unemployment with competing risks of its terminating into employment, labour market training or economic inactivity. Taking into account the wide period of observation and opportunities to analyse processes of labour market integration during various periods of economic development in Finland, in combination with the individualistic character of the labour careers of immigrants, this research is beneficial owing to the many various findings concerning labour market integration of immigrants. The approach undertaken in this research has a dualistic “descriptive-dynamic” character under which integration is understood as a never-ending process, which is conditioned by a time period of long-term existence and a context of solitary action. We find that transitions out of unemployment spells have a cyclical character; after every new “cycle” in unemployment, the probability of terminating unemployment decreases further. We also find that ascriptive factors make sense in the process of job-placement of immigrants from unemployment. Therefore, the gender, education and age of immigrants, as well as the effect of the period in which first unemployment occurred, potentially predict transitions out of unemployment and further labour market integration of immigrants.

The allosteric SERCA (Sarcoplasmic/Endoplasmic Reticulum Ca2+-ATPase) activator CDN1163 has been recently added to the group of pharmacological tools for probing SERCA function. We chose to investigate the effects of the compound on T lymphocyte Ca2+ stores, using the well-described Jurkat T lymphocyte as a reliable cell system for Ca2+ signaling pathways. Our study identified the lowest concentrations of the SERCA inhibitors thapsigargin (TG) and 2,5-di-(tert butyl)-1,4-benzohydroquinone (tBHQ) capable of releasing Ca2+, permitting the differentiation of the TG-sensitive SERCA 2b Ca2+ store from the tBHQ-sensitive SERCA 3 Ca2+ store. We proceeded to test the effects of CDN1163 on Ca2+ stores, examining specific actions on the SERCA 2b and SERCA 3 Ca2+ pools using our low dose SERCA blocker regimen. In contrast to previous work, we find CDN1163 exerts complex time-sensitive and SERCA isoform-specific actions on Ca2+ stores. Surprisingly, short-term exposure (0-30 minutes) to CDN1163 perturbs T cell Ca2+ stores by suppressing Ca2+ uptake with diminished Ca2+ release from the SERCA 2b-controlled store. Concomitantly, we find evidence for a SERCA-activating effect of CDN1163 on the SERCA 3 regulated store, given the observation of increased Ca2+ release inducible by low dose tBHQ. Intriguingly, longer-term (&gt;12 hours) CDN1163 exposure reversed this pattern, with increased Ca2+ release from SERCA 2b-regulated pools, yet decreased Ca2+ release responses from tBHQ-sensitive SERCA 3 pool. Our results reveal differential effects of CDN1163 on Ca2+ stores regulated by distinct SERCA isoforms, prompting the need for careful interpretation of the compound’s effects, particularly in cells expressing multiple SERCA isoforms.

The aim of this study is to analyze the characteristics of drought such as intensity, cumulative curves and trends, based on SPEI (Standardized Precipitation Evapotranspiration Index) at 8 stations in Korea from 1981 to 2010. The traditional SPEI is based on Thornthwaite equation for estimating evapotranspiration; SPEI_th. However, a standard of agricultural water management in Korea suggests FAO Penman-Monteith equation; SPEI_pm. In this study, we analyzed the intensity and trends of drought using SPEI_th and SPEI_pm, respectively, and analyzed the relationship between them. Both of central and southern region, the SPEIs were below -1.0 (moderated drought) for the periods May-August in the representative drought year such as 1988, 2001, and 2008-09. The frequency of drought was higher in southern region than central region. In addition, SPEI_pm showed slightly more intensive drought rather than SPEI_th except for Chuncheon and Gwangju. In 5 stations except for Cheoncheon, Gwangju and Jinju, the cumulative probability that SPEI_pm is below -1.5 was significantly increased from 1981-1995 to 1996-2010. As the results of drought trends, the increasing trend of SPEIs was shown on fall season, and the cumulative probability that SPEI_pm is below -1.5 was also significantly increased.

How to build an optimal model where three terms “time, causality, and entropy” will be interrelated in a most correct way? This task has a semantic and physical aspect. We give in this article the solution that is based only on elementary perception. In physics, we experience time with our senses as the duration of material change running in space. This fact is the standpoint for our model where causality is only a principle, it is not a physical actuality and entropy runs only in space and not in time. Time is merely a duration of entropy increasing and is entering existence when measured by the observer.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

The prognostic value of inflammatory indices such as absolute monocyte count (AMC) has been a subject of interest in recent prostate cancer (PCa) literature, while hemoglobin concentration (HGB) has been recognized as a survival factor in castration-resistant metastatic prostate cancer, but its value remains unclear in localized disease. The aim of this study was to test the prognostic value of these two simple and inexpensive biomarkers for survival based on a cohort of 1016 patients treated with primary radiotherapy and androgen deprivation therapy for localized or locally advanced intermediate- or high-risk PCa. Complete survival data was available for all cases based on the National Cancer Registry with a median observation time of 120 months (IQR 80.9-144.7). Missing blood test data were supplemented using the Nearest Neighbor Imputation, and the Cox proportional hazards regression model was used for analysis. The median age was 68.8 years (IQR 63.3-73.5). The five-year overall survival was 82.8%, and 508 patients were alive at the time of analysis. The median time between blood tests and the first day of radiotherapy was 6 days (IQR 0-19). HGB (p = 0.009) and AMC (p = 0.003) were independent prognostic factors for survival, along with age, ISUP Grade Group, clinical T stage and maximum PSA concentration. The study demonstrated that HGB and AMC can be useful biomarkers for overall survival in patients treated with radiotherapy for localized intermediate- or high-risk PCa.

The absolute absorption cross section of the ethyl peroxy radical, C2H5O2, in the Ã←X ̃ electronic transition with the peak wavelength at 7596 cm-1, has been determined by the method of dual wavelengths time resolved continuous wave cavity ring down spectroscopy. C2H5O2 radicals were generated from pulsed 351 nm photolysis of C2H6/Cl2 mixture in presence of O2 and detected on one of the CRDS paths. Two methods have been applied for the determination of the C2H5O2 absorption cross section: (i) based on Cl-atoms being converted alternatively to either C2H5O2 by adding C2H6 or to hydro peroxy radicals, HO2, by adding CH3OH to the mixture, whereby HO2 was reliably quantified on the second CRDS path in the 21 vibrational overtone at 6638.2 cm-1 (ii) based on the reaction of C2H5O2 with HO2, measured under either excess HO2 or under excess C2H5O2 concentration. Both methods lead to the same peak absorption cross section of C2H5O2,7596 cm-1 = (1.0±0.2) × 10-20 cm2. The rate constant for the cross reaction between of C2H5O2 and HO2 has been measured to be (6.5±1.6) × 10-12 cm3 molecule-1 s-1.

A model of space-time is presented, whose origin is set before the appearance of any universe. It uses concepts of previous work, a central one being that the information about the laws of nature is stored locally everywhere in space such that all physical processes obey them. Since information storage is bound to matter or energy, space is assumed to consist of dark energy (DE), which thus assumes an importance far beyond its function as a stopgap for an energy deficit in our universe ( U ). The primordial state (PS) is a timeless and relatively large space of 3 dimensions described by a Wheeler DeWitt (WDW) equation, whose solution is interpreted as an arrangement of very many space quanta and possesses properties that remind of the time-honored concept of the unmoved mover. The comparison of WDW solutions belonging to different mass densities of the DE favors one in which the space quanta are mini black holes. This allows the space quanta to be imagined as mass points which are kept at a distance compatible with the quantum volume by the Pauli principle or something equivalent. Triggered by a dramatic increase in probability, the PS is followed by a time-controlled sequence of quantized expansion states (ES i ). The concomitant emergence of time occurs in a lightning huge crash, consuming almost all DE of the PS. The subsequent quantized ES i emerge from a WDW equation, novelly derived from a solution of the modified cosmic momentum equation, which classically describes an exponential space expansion (CS). The huge volme of the ES i is also used as size of the PS. Information is assumed to be geometrically stored in arrangements of space quanta similar to how genetic information is stored in DNA molecules. During the CS information must be transferred from already existing "information quanta" to new ones. This requires time, slows down the expansion and is taken into account by a friction term in the cosmological momentum equation thus modified. Since the Friedmann-Lemaître (FL) equation remains fully valid, the model is widely based on recognized equations, so that some results may be understood as interpretations.

Considered is “time as an interval” including time from the past and from the future, in contrast to time as a moment. Equilibrium as the basis for a description of changing properties in physics is understood to depend on the “mean velocity theorem”, while a “time” of equilibrium resembles a center of weight. This turns out to be a good method to derive properties for any function of time t including space coordinates q(t) and expressions for the time dependent Hamiltonian. Introduced are derivatives depending on time intervals instead of time moments and with these a new relation between the Lagrangian L and the Hamiltonian H. As an application introduced is a step by step method to integrate stationary state “local” time interval measurements to beyond “locality” in General Relativity. Because of limits on the measures of the resulting time intervals and their asymmetry, this allows for a probabilistic interpretation of quantities that have these intervals as time domain in QM. Their asymmetry also questions the time reversal symmetry of GR. Another application of time intervals is the discussion of the measurement of starlight radiation energy and QM wave packet collapse as an example of a time dependent Hamiltonian. Finally a relation between starlight frequency, metric and space- and time intervals is found. Discussed is how finite and asymmetric time intervals correspond to time dependent H and symmetric infinite time intervals to a time independent H. From there, in cosmological perspective, finite time intervals can help to describe how entropy change could relate to dark energy.

Proteomic technology has improved at a staggering pace in recent years, with even practitioners challenged to keep up with new methods and hardware. The most common metric used for method performance is the number of peptides and proteins identified. While this metric may be helpful for proteomics researchers shopping for new hardware, this is often not the most biologically relevant metric. Biologists often utilize proteomics in the search for protein regulators that are of lower relative copy number in the cell. In this review, I re-evaluate untargeted proteomics data using a simple graphical representation of the absolute copy number of proteins present in a single cancer cell as a metric. By comparing single shot proteomics data to the coverage of the most in-depth proteomic analysis of that cell line acquired to-date we can obtain a rapid metric of method performance. Using a simple copy number metric allows visualization of how proteomics has developed in both sensitivity and overall dynamic range when using both relatively long and short acquisition times. To enable reanalysis beyond what is presented here, two available web applications have been developed for single and multi-experiment comparisons with reference protein copy number data for multiple cell lines and organisms.

In this research, we investigate the bending of photon light and/or time-like geodesics within the context of four-dimensional space-time geometry, specifically in the presence of topological defects. These topological defects manifest as cosmic string space-time configurations, encompassing screw dislocation, spiral dislocation, and spacelike dislocation. Our primary objective is to determine the extent of deflection experienced by light-like and time-like geodesics and analyze how this deflection is affected by the cosmic string parameter, screw dislocation parameter, and spacelike dislocation parameter. To accomplish this, we employ a derivation technique that centers on the observation that photon rays (light-like geodesics) and/or time-like geodesics follow paths parallel to the z-axis while maintaining a constant radius along the cylinder.

This addendum contains clarifications and a sharpening of some of the results on the VIT transform framework developed in [1]. The focus is on the right-coefficient and left- coefficient forms of the transform, the extraction of a first-order term from a left polynomial fraction, and the application to linear time-varying systems.

Background: The electroretinogram is a clinical test used to assess the function of the photoreceptors and retinal circuits of various cells in the eye, with the recorded waveform being the result of the summated response of neural generators across the retina. Methods: The present investigation involved an analysis of the electroretinogram waveform in both the time and time-frequency domain through the utilization of the discrete wavelet transform and continuous wavelet transform techniques. The primary aim of this study was to monitor and evaluate the effects of treatment in a New Zealand rabbit model of endophthalmitis via electroretinogram waveform analysis and to compare these with normal human electroretinograms Results: The wavelet scalograms were analyzed using various mother wavelets, including the Daubechies, Ricker, Wavelet Biorthogonal 3.1 (bior3.1), Morlet, Haar, and Gaussian wavelets. Distinctive variances were identified in the wavelet scalograms between rabbit and human electroretinograms. The wavelet scalograms in the rabbit model of endophthalmitis showed recovery with treatment in parallel with the time -domain features. Conclusions: The study compared Adult, Child, and Rabbit electroretinogram responses using DWT and CWT, finding that Adult signals had higher power than Child signals, and Rabbit signals showed differences in a-wave and b-wave depending on the type of response tested, while Haar Wavelet was found to be superior in visualizing frequency components in electrophysiological signals in following the treatment of endophthalmitis and may give additional outcome measures for the management of retinal disease.

Efficient use of the operating room (OR) is crucial for any hospital. One of the major inefficiencies in the OR is surgical cases not starting or finishing on time as scheduled. When a case is delayed, it affects all subsequent cases in that OR. This study uses discrete choice analysis to determine the significant factors, including team familiarity, that influence OR case on-time start and finish. A case is considered on-time if the documented procedure start and finish times are no more than 10 minutes after the scheduled start and finish times. The analysis uses surgical case data from a large tertiary referral hospital and academic center in Greenville, South Carolina. The case data includes all surgical cases (15,091) performed during regular workdays in 2013. Two binary logit models are developed: one for case on-time start and one for case on-time finish. Results indicate that higher team familiarity between surgeon and anesthesiologist, surgeon and circulating nurse, surgeon and scrub nurse, and surgeon and CRNA improve the likelihood of an OR case on-time start and on-time finish. This finding indicates that the OR scheduling staff in the study hospital make a concerted effort to schedule the surgical teams with members who have worked well together in the past.

Time estimation was investigated in 24 healthy adults, 12 women and 12 men, before and after an exhaustive exercise. We compared the capability of estimating time intervals in the range from 1 to 5 s using tasks requiring mental count and tasks that did not allow the mental count. Time estimation and blood lactate levels were evaluated before and at the end of the exercise. We found that the perception of time intervals between 1 and 5 s was affected at the end of the exercise. The observed effects, associated with a significant increase in blood lactate levels, were different in the two types of time estimation used in the present study. In experimental conditions in which participants had to evaluate duration of the time interval by mental counting, at the end of exercise a significant reduction in the overestimation of time made at rest was observed. On the other hand, when participants had to assess the difference in duration between two events without the possibility to mentally count, at the end of the exercise a significant deterioration in performance was observed. In both cases, no gender differences were seen.

This article begins with exploring fundamental limits in the universe. It examines key principles, such as the uniformity of physical laws and Energy conservation, that lead to the principles of maximum speed, locality, and maximum density. These universal limits govern physical phenomena, culminating in very interesting results.They led to the exploration of Quantum black holes. Quantum black holes are relativistically revolving miniature charged black holes consisting of a single core at the highest possible density. They are the only structures small enough to keep all charges quantized (including gravitational charges). I then demonstrated that quarks and leptons comprise smaller entities - the Quantum Black Holes. Exploring these elementary particles reveals that they release their Energy outward, altering the curvature of nearby space-time and providing new insights. We can characterize movements and processes in local space-time with four sets of equations representing the four charge types and one set representing Dark Matter. By the end of the article, I prove that Quantum black holes explain the quantization of gravity, the nature of Luminous and dark Matter, the Mass, size, and (quantized) charges quantities of elementary particles and the nature of neutrino oscillations.

The Thermocontextual Interpretation (TCI) is proposed here as an alternative to existing interpretations of physical states and time. Prevailing interpretations are based on assumptions rooted in classical mechanics. Logical implications include the determinism and reversibility of change, and an immediate conflict. Determinism underlies causality, but causality implies a distinction between cause and effect and an arrow of time, conflicting with reversibility. Prevailing interpretations also fail to explain the empirical irreversibility of wavefunction collapse without untestable and untenable metaphysical implications. They fail to reconcile nonlocality and relativity without invoking superdeterminism or unexplained superluminal correlations. The Thermocontextual Interpretation defines a system’s state with respect to its actual surroundings at a positive ambient temperature. The TCI bridges existing physical interpretations and thermodynamics as special cases, which define states either with respect to an absolute-zero reference or with respect to a thermally equilibrated reference. The TCI defines system time as a complex property of state spanning both reversible mechanical time and irreversible thermodynamic time, and it distinguishes between system time and the reference time of relativity and causality, as measured by an observer’s clock. And, the TCI provides a physical explanation for nonlocality, consistent with relativity, without hidden variables, superdeterminism, or “spooky action.”

The prevailing interpretations of physics are based on deeply entrenched assumptions, rooted in classical mechanics. Logical implications include: the denial of entropy as a fundamental physical property, and the inability to explain irreversible change, random quantum measurements, or nonlocality without untestable and implausible metaphysical implications. We propose a conceptual model that is based on empirically justifiable assumptions and consistent with observations. The WYSIWYG Conceptual Model (WCM) assumes no hidden properties: “What You can See Is What You Get.” The WCM contextually defines a system’s state with respect to its actual ambient background, and it extends existing models of physical reality by defining entropy and exergy as objective contextual properties of state. The WCM establishes the irreversible dissipation of exergy and the Second law of thermodynamics as a fundamental law of physics, it recognizes physical randomness, and it provides a physical explanation for nonlocality, consistent with Special Relativity, without hidden variables, superdeterminism, or “spooky action.”

This paper presents three types of sliding mode controllers for a magnetic levitation system. First, a proportional-integral sliding mode controller (PI-SMC) is designed using a new switching surface and a proportional plus power rate reaching law. The PI-SMC is more robust than a feedback linearization controller in the presence of mismatched uncertainties and outperforms the SMC schemes reported recently in the literature in terms of the convergence rate and settling time. Next, to reduce the chattering phenomenon in the PI-SMC, a state feedback-based discrete-time SMC algorithm is developed. However, the disturbance rejection ability is compromised to some extent. Furthermore, to improve the robustness without compromising the chattering reduction benefits of the discrete-time SMC, mismatched uncertainties like sensor noise and track input disturbance are incorporated in a robust discrete-time SMC design using multirate output feedback (MROF). With this technique, it is possible to realize the effect of a full-state feedback controller without incurring the complexity of a dynamic controller or an additional discrete-time observer. Also, the MROF-based discrete-time SMC strategy can stabilize the magnetic levitation system with excellent dynamic and steady-state performance with superior robustness in the presence of mismatched uncertainties. The stability of the closed-loop system under the proposed controllers is proved by using the Lyapunov stability theory. The simulation results and analytical comparisons demonstrate the effectiveness and robustness of the proposed control schemes.

The possibility to test a radio frequency transceiver through the use of appropriate channel emulators allows to evaluate their performance under various operating conditions. Many systems are able to operate with a relatively limited instantaneous bandwidth by applying known statistical models. Sometimes it is necessary to evaluate the performance of a RF transceiver installed on high or very high speed platforms over predictable trajectories using optionally DEMs (Digital Elevation Models)data of the terrain to estimate the number of stimulated paths and their contributions during the flight. When the instantaneous bandwidth of the signal becomes high (over several hundred of MHz), one of the most important phenomenon to consider is the Doppler spread induced by the channel and traditional narrowband models become unuseful. In this paper there are presented some results when a time expansion is adopted in order to emulate the transceiver dynamic and the consequent Doppler spread with the aim to control the spectral purity of the emulated propagation channel.

The continuous nature of space and time is a fundamental tenet of many scientific endeavours. That digital representation imposes granularity is well recognized but whether it is possible to address space completely remains unanswered. Part 1 argues that Hales’ proof of Keppler’s conjecture on the packing of hard spheres suggests the answer to be ‘no’, providing examples of why this matters in GIS generally and spatio-temporal GIS in particular. Part 2 seeks to resolve the dichotomy between continuous and granular space, showing how a continuous space may be emergent over a random graph. However, its projection into 3D/4D imposes granularity. Perhaps surprisingly, representing space and time as locally conjugate may be key to addressing a ‘smooth’ spatial continuum. This insight leads to the suggestion of Face Centered Cubic Packing as a space-time topology but also raises further questions for spatio-temporal representation.

Multicellular life evolved from simple unicellular organisms that could replicate indefinitely being essentially ageless. At this point, life split into 2 fundamentally different cell types: the immortal germline representing an unbroken lineage of cell division with no intrinsic endpoint and the mortal soma which ages and dies. In this review, we describe the germline as clock-free and the soma as clock-bound and discuss aging with respect to 3 DNA-based cellular clocks (telomeric, DNA methylation, and transposable element). The ticking of these clocks corresponds to the stepwise progressive limitation of growth and regeneration of somatic cells that we term, somatic restriction. Somatic restriction acts in opposition to strategies that ensure continued germline replication and regeneration. We thus consider the plasticity of aging as a process not fixed to the pace of chronological time but one that can speed up or slow down depending on the rate of intrinsic cellular clocks. We further describe how germline factor reprogramming might be used to slow the rate of aging and potentially reverse it by causing the clocks to tick backwards. Therefore, reprogramming may eventually lead to therapeutic strategies to treat degenerative diseases by altering aging itself, the one condition common to us all.

The stock beta coefficient literature extensively discusses the proper methods for the estimation of beta as well as its use in asset valuation. However, there are relatively few references with respect to the appropriate time horizon that investors should utilize when evaluating the risk-return relationship of a stock. We examine the appropriate time horizon for beta estimation differentiating our results by sector according to the Industry Classification Benchmark. We employ data from the NYSE and we estimate varying lengths of beta employing data from 30 to 250 trading days. The constructed beta series is then examined for the presence of breaks using the endogenous structural break literature. Results show evidence against the use of betas that employ more than 90 trading days of data provisional to the sector under study.

This paper examines the effect of chronotype on the delinquent credit card payments and stock market participation through preference channels. Using an online survey of 455 individuals who have been working for 3 to 8 years in companies in mainland China, the results reveal that morningness is negatively associated with delinquent credit card payments. Morningness also indirectly predicts delinquent credit card payments through time preference, but this relationship only exists when individuals’ monthly income is at low and average level. On the other hand, financial risk preference accounts for the effect of morningness on stock market participation. Consequently, an additional finding is that morningness is positively associated with financial risk preference, which contradicts previous finding in the literature. Finally, based on the empirical evidence, we discuss the plausible mechanisms that may drive these relationships and the implications for theory and practice. The current study contributes to the literature by examining the links between circadian typology and particular financial behaviours of experienced workers.

Noise model selection criteria has a significant impact on identifying the stochastic noise proper-ties of any GNSS daily coordinate time series. The low-frequency random walk noise existing in these time series could lead to overestimation of the tectonic rate, so it is of great significance to accurately detect the random walk component. This study focuses on noise model estimation cri-terion (BIC_tp) derived from the AIC and the BIC by introducing 2π factors. It is more sensitive to abnormal steps (random jumps). Using observation data from 72 GNSS stations from 1992 to 2022 and simulated data, four combined noise models are used to explore the impacts of time se-ries lengths (ranging from2 to 24 years) and data loss (between 2% and 30%) on noise models and velocity estimation. The results show that as the time length increased, the selected optimal noise model, and the estimated uncertainty of the tectonic trend with different data gap, gradually con-verge. When the time length is short (less than 8 years), it could lead to the FNRWWN, FNWN, and PLWN models being mistakenly estimated as GGMWN models, thereby affecting the accura-cy of determining the station velocity parameters. When the time length is 12 years, the RW noise component is more probably detected, As the time length increases, the impact of RW on velocity uncertainty is weakened. Finally, we conclude that for a time series with a minimum time length of 12 years, both the selection of the optimal stochastic noise model and the estimation of the ve-locity parameters are reliable.

We aimed to investigate the ability of children aged 5–14 years old (preschoolers, primary schoolers, and preteens) to assess and anticipate time intervals. 287 Russian children aged 5–14 years old and 26 adults of control group participated in our study. The neuropsychological assessment, Wechsler Intelligence Scale for Children and a battery of time-related tests were applied. All groups of children overestimated the event’s duration, although the accuracy of the second estimations increased among the participants aged 6–8 years after a prompt was offered. A zone of proximal development for time anticipation task was detected for children aged 9-11 years, when the prompt could significantly improve the accuracy of time perception. The participants overestimated the duration of both upcoming and past events, with the degree of overestimation being found to be negatively correlated with age. Further, a higher degree of accuracy in terms of time estimation was found to be correlated with higher scores on the attention and memory tests, and accuracy of time anticipation was associated with scores of praxis test.

In this research article we solve the problem of synchronization and anti-synchronization of chaotic systems described by discrete and time-delayed variable fractional order differential equations. To guarantee the synchronization and anti-synchronization of these systems, we use the well-known PID control theory and the Lyapunov-Krasovskii stability theory for discrete systems of variable fractional order.We illustrate the results obtained through simulation with examples, in which it can be seen that our results are satisfactory, thus achieving synchronization and anti-synchronization of chaotic systems of variable fractional order with discrete time delay.

In this perspective article, we ponder topographical enhancements of artificial neural networks. In our recent paper in JMLR, we proved a quasi-equivalence between the network width and depth and also discussed the power of intra-links, which can be viewed as network height. In 1982, Hopfield published a network to model human associative memory, which contains many loops for dynamic evolution toward fixed points. Based on noising-denoising loops, diffusion models are recently developed to enable Bayesian modeling and inference with big data. Furthermore, we envision development of multi-AI-agent systems through “netware” engineering as a quantum leap of software engineering for emergent behaviors and autonomous AI at individual and population levels. We believe that the novel use of links and loops in space and time via multi-scale coupling would catalyze the next-generation neural networks.

A time interval only description necessarily needs its own independent definitions, without one moment time coordinates to it. In this paper derived are time interval only set properties, including commutation relations, addition, multiplication and derivatives. Time interval only set commutation relations, consistent with one moment time set properties, are introduced by defining correspondence relations for these sets. Time development and equilibrium within the time interval description depend on the well-known ‘mean velocity theorem’ and the time interval version of the Legendre transform. In contrast, usually applied is only the traditional vector and one moment time coordinate kinematic approach from Newton’s laws. The main results of this paper are correspondences and time interval only set commutation relations. All other properties are derived from these results, while for the time interval only set, different from the one moment time set the canonical property is not valid. The time interval only description can be applied assuming spherical symmetric star-source radiation propagation, with finite time intervals for realistic measurement events. From time development with (a-)symmetry of time intervals, and from Curie’s principle, change can be described with a set theoretic approach. Time interval only set properties include the time interval only version of Noether charges and structure constants. A time interval only description for wave propagation, including group-velocity, for zero and non-zero mass wave particles, relates to the properties of the time interval only set. A second result in terms of the time interval only description is propagation wave energy equivalence with gravitation energy, derived from time interval only set commutation relations. A time interval approach, however including one moment time description dependence, was introduced in earlier publications of this author. In part 1 investigated are the time interval only set and its properties, a forthcoming part 2 to application of the time interval only description to specific groups of stars as emission sources.

Viral variant analysis is a bedrock of the disease surveillance. When combined with temporospatial analysis variant analysis can further the knowledge of disease spread in a study area. This paper suggests a method to perform the analysis in an operational setting which will allow for real-time surveillance of viral variants and allow local public health professionals to rapidly respond to changes in the evolution of the disease. This method includes three main subprocesses: preprocessing, analysis, and rendering. This method can be performed across multiple software platforms. A use case is given in which it was found that this method helped a hospital system understand the spread of SARS-CoV-2 in Northeast, Ohio.

Phenomenon of vacuum fluctuations of virtual particles in high energy physics has been mathematically modeled by a third order differential equation. Aim of present theory is to unravel underlying mathematical equation capable of explaining microscopic phenomenon of vacuum fluctuations. Solution of such a differential equation after applying appropriate boundary conditions gives an acceptable wave function i.e. . Operation of energy and time operator on this wave function proves that these operators do not hold commutative property. Time energy uncertainty principle has been derived by calculating variance of energy and time for the same wave function.

The nonlocal boundary value problem, dtρu(t)+Au(t)=f(t) (0&lt;ρ&lt;1, 0&lt;t≤T), u(ξ)=αu(0)+φ (α is a constant and 0&lt;ξ≤T), in an arbitrary separable Hilbert space H with the strongly positive selfadjoint operator A, is considered. The operator dt on the left hand side of the equation expresses either the Caputo derivative or the Riemann-Liouville derivative; naturally, in the case of the Riemann - Liouville derivatives, the nonlocal boundary condition should be slightly changed. Existence and uniqueness theorems for solutions of the problems under consideration are proved. The influence of the constant α on the existence of a solution to problems is investigated. Inequalities of coercivity type are obtained and it is shown that these inequalities differ depending on the considered type of fractional derivatives. The inverse problems of determining the right-hand side of the equation and the function φ in the boundary conditions are investigated.

The triplet excited state reactivity towards phenolic hydrogen of the -diketones benzil and 2,2´-furil in the ionic liquid 1-n-butyl-3-methyl imidazolium hexafluorophosphate [bmim.PF6] was investigated employing the nanosecond laser flash photolysis technique. Irradiation (lmax=355 nm) of benzil yields its triplet excited state with lmax at 480 nm and tT=9.6 μs. Under the same conditions, 2,2’-furil shows a triplet-triplet absorption spectrum with bands at 380, 410, 450, and 650 nm and tT=1.4 μs. Quenching rate constants (kq) of the reaction between benzil triplet and substituted phenols ranged from 1.4x107 L mol-1 s-1 (para-chlorophenol) to 1.8x108 L mol-1 s-1 (para-methoxyphenol). A new transient was formed in all cases, assigned to the benzil ketyl. Similar results were obtained for the quenching of 2,2’-furil triplet by phenols, for which kq ranged from 1.9x108 L mol-1 s-1 (para-chlorophenol) to 2.2x108 L mol-1 s-1 (para-methoxyphenol). The 2,2’-furil ketyl radical was also observed in all cases (lmax=380 nm). The quenching rate constants are almost independent of the substituent and diffusion-controlled (kq ~ 108 L mol-1 s-1). The proposed mechanism for the phenolic hydrogen abstraction by benzil and 2,2´-furil triplet may involve a proton-coupled electron transfer reaction, ultimately leading to the radical pair ketyl/aryloxyl.

This manuscript presents a system that can generate a 2D grid map and a 3D voxel model of an environment by fusing multiple sensors integrated into a robot. The fusion of these sensors is done by utilizing Robot Operating System (ROS) and some of its libraries. The sensors that are fused in the robot are a Light Detection and Ranging (LIDAR), Inertial Measurement Units (IMU), wheel encoders, and a Time-of-Flight camera. With the fusion of the point cloud data information obtained with the Time-of-Flight camera, the laser information of the LIDAR sensor, in addition to the odometry generated with the other sensors, a 2D grid map and a 3D model of two different environments were created, thus testing the performance of the system.

Physical Unclonable Functions (PUFs) based on the retention times of the cells of a Dynamic Random Access Memory (DRAM) can be utilised for the implementation of cost-efficient and lightweight cryptographic protocols. However, as recent work has demonstrated, the times needed in order to generate their responses may prohibit their widespread usage. In order to address this issue, the Row Hammer PUF has been proposed by Schaller et al. [1], which leverages the row hammer effect in DRAM modules to reduce the retention times of their cells and, therefore, significantly speed up the generation times for the responses of PUFs based on these retention times. In this work, we extend the work of Schaller et al. by presenting a run-time accessible implementation of this PUF and further reducing the time required for the generation of its responses. Additionally, we also provide a more thorough investigation of the effects of temperature variations on the the Row Hammer PUF and briefly discuss potential statistical relationships between the cells used to implement it. As our results prove, the Row Hammer PUF could potentially provide an adequate level of security for Commercial Off-The-Shelf (COTS) devices, if its dependency on temperature is mitigated, and, may therefore, be commercially adopted in the near future.

In Thailand, parking time violation is a major problem, especially for mini-marts. At present the task of detecting parking time violation is mainly conducted manually using Closed-Circuit Television (CCTV). This method requires additional human labour to track incoming and outgoing vehicles. Therefore, low cost time violation tracking is needed. To the best of our knowledge, there has not been any research for parking violation detection and tracking conducted for parking time limits. This paper introduces a novel parking time violation detection algorithm using the Yolov8 and DeepSORT tracking algorithms to track vehicles in consecutive frames. The presented parking violation tracking algorithm can provide a guideline for research in parking time violation detection.

The phenomenon of dissipative self-organization is studied on the example of time-crystal networks. Particular attention was given to transient processes, attractor topologies, phase transitions, and asymptotic stability. New concepts were introduced, including topological phases, spinorial states, and bond flavors. Concepts such as ground states, chemical potentials, elastic forces, temperature, and statistical distributions were endowed with a new meaning associated with asymptotic stability. Phenomena usually attributed exclusively to quantum physics have been shown to occur in this essentially classical environment. They coexist with, and in some cases, such as charge quantization, are related to the phenomenon of time dilation. The approach was applied to model vacuum self-organization. We have shown that under the ac-tion of competing forces, such as gravity and antigravity, a cascade of phase transitions can transform an unorganized vacuum into phases in which interactions, fields and waves resemble electromagnetic, weak, and strong, and their elements can be used as building blocks for prototype particles. In addition, some interrelation field parameters and probabilities of particle transmutations were calculated, which are not predicted by the standard model. The results are consistent with the experiment. The presented material and methodology may be of interest for studying self-organization in different environments.