YG-13A represents the highest level of Chinese SAR satellites to date. In this paper, we report on experiments conducted to improve and validate ranging accuracy with YG-13A. We analyze the error sources in the YG-13A ranging system, such as atmospheric path delay, and transceiver channel delay. A real-time atmospheric delay correction model is established to calculate the atmospheric path delay, considering the troposphere delay and ionosphere delay. Six corner reflectors (CRs) were set up to ensure the accuracy of validation methods. Pixel location accuracies of up to 0.479-m standard deviation can be achieved after a complete calibration. We further demonstrate that the adjustment of the CRs can cause a marginal loss of ranging precision. After eliminating this error, the ranging accuracy is improved to 0.237 m. For YG-13A, a single frequency GPS receiver is used and the orbital nominal accuracy is 0.3 m, which is the biggest factor restricting its ranging accuracy. Our results show that the ranging accuracy of YG-13A can achieve decimeter-level, which is lower than centimeter-level accuracy with TerraSAR-X loading a dual frequency GPS. YG-13A has great convenience in terms of access to control points and target location that does not depend on ground equipment.

The flowering period of rice significantly impacts variety adaptability and yield formation. Properly shortening the reproductive period of rice varieties can expand their ecological range without significant yield reduction. Targeted genome editing, like CRISPR/Cas9, is an ideal tool to fine-tune rice growth stages and boost yield synergistically. In this study, we developed a CRISPR/Cas9-mediated multiplex genome editing vector containing five genes related to three traits: Hd2, Ghd7, and DTH8 (flowering stage genes), along with the recessive rice blast resistance gene Pi21 and the aromatic gene BADH2. This vector was introduced into the high-quality Geng rice variety in Zhejiang province, Jiahe212 (JH212), resulting in 34 T0 plants with various effective mutations. Among the 17 mutant T1 lines, several displayed diverse flowering dates, but most exhibited undesirable agronomic traits. Notably, three homozygous mutant lines (JH-C15, JH-C18, and JH-C31) showed slightly earlier flowering dates without significant differences in yield-related traits compared to JH212. Through special Hyg and Cas marker selection of T2 plants, we identified 7, 6, and 2 fragrant glutinous plants devoid of transgenic components, respectively. These single plants will serve as sib lines of JH212 and potential resources for breeding applications, including maintenance lines for Xian-Geng interspecific three-line hybrid rice. In summary, our research offers practical insights and potential resources for targeted improvement of Geng rice varieties, and would also promote the Geng rice varieties expending from the southward to the northward.

The utilization of electroporation for delivering the CRISPR/Cas9 system components has enabled efficient gene editing in mammalian zygotes, facilitating the development of genome-edited animals. In our study，This research focused on targeting the ACTG1 and MSTN genes in sheep, revealing a threshold phenomenon in electroporation with a voltage tolerance in sheep in vitro fertilization (IVF) zygotes. Various poring voltages near 40V and pulse durations were examined for electroporating sheep zygotes. The study concluded that stronger electric fields required shorter pulse durations to achieve the optimal conditions for high gene mutation rates and reasonable blastocyst development. The investigation also assessed the quality of Cas9/sgRNA ribonucleoprotein complexes (Cas9 RNPs) and their influence on genome editing efficiency in sheep early embryos. It was highlighted that pre-complexation of Cas9 proteins with single-guide RNA (sgRNA) before electroporation was essential for achieving a high mutation rate. The use of suitable electroporation parameters for sheep IVF zygotes led to significantly high mutation rates and heterozygote ratios. By delivering Cas9 RNPs and single-stranded oligodeoxynucleotides (ssODNs) to zygotes through electroporation, targeting the MSTN (Myostatin) gene, a knock-in efficiency of 26% was achieved. The successful generation of MSTN-modified lambs was demonstrated by delivering Cas9 RNPs into IVF zygotes via electroporation.

The paper introduces a control hybrid model that is designed on the basis of OOSEM (Object-Oriented Systems Engineering Method), MDA (Model-Driven Architecture) concepts, RealTime UML/SysML (Unified Modeling Language/Systems Modeling Language), and an algorithm based on UKF (Unscented Kalman Filter). This hybrid model enables the implementation of control elements for autonomous underwater vehicles (AUVs) and can be adapted to reuse for most standard AUV platforms. To obtain this goal, the dynamic model of AUV is integrated with the following specializations of OOSEM/MDA, in which the analysis model is clarified via the use-case model definition and then combines with HA (hybrid automata) to precisely define the requirements for control. Next, the designed model is specialized via real-time UML/SysML to get the core control blocks, which describe the behaviors and structures of control parts in detail. This design model is then transformed into the model of implementation with the assistance of round-trip engineering to conveniently realize the controller of AUVs. Based on this new model, an AUV controller for low-cost turtle-shaped AUVs is implemented that performs tracking for a planar trajectory with accepted feasibility.

: This study focuses on optimizing chlorophyll extraction techniques and strategically placing leaf disks to enhance chlorophyll concentration in sesame (Sesamum indicum L.) leaves. Thirty sesame genotypes, categorized into light green (LG), middle green (MG), and deep green (DG) pigment groups based on leaf coloration, were selected from a larger pool of field-grown accessions. The investigation involved determining optimal SPAD value index measurements, quantifying pigment concentrations, exploring extraction solvents, and selecting suitable leaf disk positions. Significant variations in chlorophyll content were observed across genotypes, greenness categories, and leaf disk positions. The categorization of genotypes into DG, MG, and LG groups revealed a correlation between leaf appearance and chlorophyll content. The study highlighted a consistent relationship between carotenoids and chlorophyll, indicating their role in adaptation to warm environments. Examination of leaf disk positions revealed a significant chlorophyll gradient along the leaf blade, emphasizing the need for standardized protocols. Chlorophyll extraction experiments identified DMSO and 96% ethanol, particularly the later incubated for 10 minutes at 85°C, as effective choices. This recommendation considers factors like cost-effectiveness, time efficiency, safety, and environmental regulations, ensuring consistent and simplified extraction processes. For higher chlorophyll extraction, focusing on leaf tips and the 75% position along the sesame leaf blade is suggested, consistently yielding higher chlorophyll content. Our findings therefore, underscores insightful knowledge on chlorophyll gradients and encouraging for standardized protocols, that enabling researchers to refine experimental designs for precise and comparable chlorophyll measurements. Recommended solvent choices ensure reliable outcomes in plant physiology, ecology, and environmental studies.

Lettuce (Lactuca sativa) is a leafy vegetable that provides a valuable source of phytonutrients for a healthy human diet. Assessment of plant growth and composition is vital for determining crop yield and overall quality, however, classical laboratory analyses are slow and costly. Therefore, new, less expensive, more rapid, and non-destructive approaches are being developed, including those based on (hyper)spectral reflectance. Additionally, it is also important to determine how plant phenotypes respond to fertilizer treatments and whether these differences in response can be detected from analyses of hyperspectral image data. In the current study, we demonstrate the suitability of hyperspectral imaging in combination with machine learning models to estimate the content of chlorophyll (SPAD), anthocyanins (ACI), glucose, fructose, sucrose, vitamin C, β-carotene, N, P, K, dry matter content, and plant fresh weight. The implemented five classification and regression machine learning models showed high accuracy in classifying the lettuces by the applied fertilizers treatments and estimating nutrient concentrations. To reduce the input (predictor data, i.e., hyperspectral data) dimension, 13 principal components were found and applied in models. The implemented artificial neural network models of the machine learning algorithm demonstrated high accuracy (r = 0.85 ... 0.99) in estimating fresh leaf weight, and contents of chlorophyll, anthocyanins, N, P, K, and β-carotene. The four applied classification models of machine learning demonstrated 100% accuracy in classifying the studied baby leaf lettuces by phenotype when certain fertilizer treatments were applied.

In the modern days the data is coming from various devices like mobiles, tabs, laptops, computers, IOT devices e.tc and is stored in the electronics form in the systems using the concept of files or data bases. Clustering Technique is used to extract data from these sources. Improving the accuracy of the model is improved using the feature selection or feature engineering or both. The feature engineering is used to add a new feature based on the global mean. Along with that new feature in addition to the feature selection increase the overall accuracy of the model.

Securing the structural safety of blades has become crucial, owing to the increasing size and weight of blades resulting from the recent development of large wind turbines. Composites are primarily used for blade manufacturing because of their high specific strength and specific stiff-ness. However, in composite blades, joints may experience fractures from the loads generated during wind turbine operation, leading to deformation caused by changes in the structural stiff-ness. In this study, 7,132 debonding damage data, classified by damage type, position, and size, are selected to predict debonding damage based on natural frequency. The change in the natural frequency caused by debonding damage is acquired through finite element (FE) modeling and modal analysis. Synchronization between the FE analysis model and manufactured blades is achieved through modal testing and data analysis. Finally, the relationship between the debond-ing damage and the change in natural frequency is examined using artificial neural network techniques

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

BACKGROUND Detecting total cholesterol in dried blood spots could aid in identifying individuals with a high likelihood of familial hypercholesterolemia and could be used as a screening measure. This study aims to assess the diagnostic accuracy of dried blood spots on Whatman 903 paper cards using a manual enzymatic technique. METHODS A total of 394 samples collected as serum and dried blood spots were compared. Cholesterol was determined in serum using the automated reference method, while cholesterol on paper was measured using a manual enzymatic method. Within- and between-day diagnostic variability were analyzed. The correlation between both methods was assessed using Passing-Bablok regression and Bland-Altman plot. Internal validation of our correlation formula was performed on 149 samples, along with external validation of the formula proposed by Corso et al. RESULTS The within- and between-day coefficient of variation was found to be lower than 10.14% and 14.09%, respectively. Method comparison yielded an area under the curve of 0.976, with a standard error of 0.009. Passing-Bablok regression indicated a precision of 0.803 and an accuracy of 0.96. Internal validation precision was measured at 0.716. Regarding internal validation, calculated cholesterol with our regression line did not differ from serum cholesterol analysis, while significant differences were observed in calculated cholesterol levels using the external formula. CONCLUSIONS Total cholesterol analysis in dot blood spots demonstrates high precision and reproducibility. This method reliably enables the incorporation of this biological marker into neonatal screening for familial hypercholesterolemia detection.

Climate change has resulted in increased incidences of abiotic stresses, such as heat, drought, salinity, and waterlogging. These stressors have a negative impact on the cotton (Gossypium hirsutum L.) crop and cause significant yield losses. Each stressor induces specific physiological and metabolic alterations interconnected with the complex changes at molecular levels. Understanding the molecular pathways that govern the cotton plant's stress responses is crucial to develop stress-tolerant cotton cultivars that can withstand different stresses. Molecular investigations have mapped the changes in the expression of stress-responsive genes, encompassing heat shock proteins and ion transporters, which play a vital role in facilitating adaptive responses. These approaches have been shown to help identify dynamic gene expression patterns and elucidate intricate regulatory networks using advanced metagenomics and multi-omics techniques. By leveraging genetic diversity and utilizing advanced molecular methods, it would be possible to develop stress-resilient cotton varieties to ensure sustainable cotton production in the face of abiotic stresses. This review provides an overview of the effects of various abiotic stressors on cotton plants, including drought, salt, heat, and waterlogged soil. We also explore the extensive network of stress-responsive genes, proteins, and signaling pathways in cotton by summarizing the studies on gene expression regulation, proteins involved in stress response, and biochemical characteristics.

In Mexico there is a deficit in the production of pine resin, because it depends on natural forests. Therefore, it is necessary to select provenances and phenotypes of potential species such as P. oocarpa. The objective was to determine the difference between provenances and the variation of resin components and quality, as well as the effect of geographic and climatic factors. Resin from five provenances was collected from southern Mexico. The percentage of rosin, turpentine and water was obtained, as well as the acidity and saponification index. P. oocarpa resin had 80.94 % rosin, 7.7 % turpentine and 11.49 % water. The saponification and acidity index was 125.47 and 117.49 mg KOH.g_1, respectively. All variables showed differences (p≤ 0.0001) between provenances. The provenance contributed between 6.44 and 11.71 % to the total variance, the error contributed between 88.29 and 93.56 %. Geographic and climatic variables only had an effect on the percentage of turpentine; the correlation was negative with altitude and longitude, but positive with temperature and precipitation. The results allow defining seed collection sites for resin plantations and orienting the selection for a P. oocarpa improvement program.

Mobile inspections conducted by intelligent tunnel robots are instrumental in broadening the inspection reach, economizing on inspection expenditures, and augmenting the operational efficiency of inspections. Despite differences from fixed surveillance, mobile-captured traffic videos have complex backgrounds and device conditions that interfere with accurate traffic event identification, warranting more research. This paper proposes an improved algorithm based on YOLOv9 and DeepSORT for intelligent event detection in edge computing mobile device using the intelligent tunnel robot. The enhancements comprise the integration of the Temporal Shift Module to boost temporal feature recognition and the establishment of logical rules for identifying diverse traffic incidents in mobile video imagery. Experimental results show that our fused algorithm achieves a 93.25% accuracy rate, an inprovement of 1.75% over the baseline. The algorithm is also applicable to inspection vehicles, drones, and autonomous vehicles, effectively enhancing the detection of traffic events and improving traffic safety.

This research introduces a hybrid feature extraction approach that combines Linear Discriminant Analysis (LDA) and Multilayer Perceptron (MLP) methods to address the challenges of reducing feature vector dimensionality and accurately classifying smartphone-based human activities. Moreover, to refine activity classification accuracy, Support Vector Machine (SVM) optimization with Stochastic Gradient Descent (SGD) is employed. LDA, a statistical tool, is leveraged to derive a new feature space for data projection, enhancing class separation and test feature label prediction. The proposed approach, named LMSS, was evaluated using the UCI-HAR dataset and compared with state-of-the-art models. The results demonstrate that the proposed approach outperformed the best-performing method over this dataset. It achieved an accuracy rate of 99.52%, precision of 99.55%, recall of 99.53%, and an F1-score of 99.54%, highlighting the effectiveness of the proposed method in accurately classifying the data.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

From an agricultural perspective, carrots are a significant tap root vegetable crop in the Apiaceae family because of their nutritional value, health advantages, and economic importance. The edible part of a carrot, known as the storage root, contains various beneficial compounds such as carotenoids, anthocyanins, dietary fiber, vitamins, and other nutrients. It has a crucial role in human nutrition as a significant vegetable and raw material in the nutraceutical, food, and pharmaceutical industries. The cultivation of carrot fields is susceptible to a wide range of biotic and abiotic hazards, which can significantly damage the plants health and decrease yield and quality. Scientific research mostly focuses on important biotic stressors, including pests like nematodes and carrot flies, as well as diseases such as cavity spots, crown or cottony rot, black rot, and leaf blight. The emerging challenges in the field include gaining a comprehensive understanding of the interaction between hosts and pathogens in the carrot-pathogen system, identifying the elements that contribute to disease development, expanding knowledge of systemic treatments, exploring host resistance mechanisms, developing integrated control programs, and enhancing resistance through breeding approaches. In fact, the primary carrot-growing regions in tropical and subtropical climates are experiencing abiotic pressures such as drought, salinity, and heat stress, which limit carrot production. This review provides an extensive, up-to-date overview of the literature on abiotic factors for enhanced and sustainable production, considering the use of intelligent technologies for farm management and production. Moreover, it addresses the current issues in the carrot production chain, opening new perspectives for the exploitation of carrots both as a food commodity and as a source of natural compounds.

Objective: The aim of this in vitro study was to evaluate the accuracy of resin-based fixed dental restorations, namely veneers, single crowns, and four-unit fixed partial dental prosthesis (FPDs) using two different 3D printers and polymer-based materials. Materials and Methods: A standard maxillary polyurethane jaw model containing prepared teeth was scanned using an intraoral scanner. The generated STL data were used to design the restorations virtually using CAD software. Two 3D printers were utilized for the provisional digital light processing and stereolithography for the castable resin patterns. Each printer produced 10 specimens of each type of restoration, for a total of 80 restorations. The 3d-printed restorations were then 3D scanned using the same intraoral scanner and evaluated for external and internal dimensional accuracy in terms of trueness and precision. A one-way ANOVA and Two-sample T-Test were implemented to compute the precision (variability between groups) and trueness (with the designed CAD model). A level of statistical significance of p-Value

The combination of micro- or nanofluidics and strong light–matter coupling has gained much interest in the past decade, which has led to the development of advanced systems and devices with numerous potential applications in different fields, such as chemistry, biosensing, and material science. Strong light–matter coupling is achieved by placing a dipole (e.g. an atom or a molecule) into a confined electromagnetic field, with molecular transitions being in resonance with the field and the coupling strength exceeding the average dissipation rate. Despite intense research and encouraging results in this field, some challenges still need to be overcome, related to the fabrication of nano- and microscale optical cavities, stability, scaling up and production, sensitivity, signal-to-noise ratio, and real-time control and monitoring. The goal of this paper is to summarize recent developments of micro- and nanofluidic systems employing strong light–matter coupling. An overview of various methods and techniques used to achieve strong light–matter coupling in micro- or nanofluidic systems is presented, preceded by a brief outline of the fundamentals of strong light–matter coupling and optofluidics operating in the strong coupling regime. The potential applications of these integrated systems in sensing, optofluidics, and quantum technologies are explored. The challenges and prospects in this rapidly developing field are discussed.

Non-toroidal shape primary pass through protection current transformers (CTs) are used to measure high currents. Their design provides them with a big airgap that allow passing several cables per phase though them, which is the main advantage versus toroidal types, as the number of CTs required to measure the whole phase current is drastically reduced. The cables pass through the transformer window can be in several positions. As the isolines of the magnetic field generated by the primary currents are centered in the cables, if these cables are not centered in the transformer window, the magnetic field will be non-uniform along the transformer core. Consequently, local saturations can appear if the cables are not properly disposed causing the malfunction of the CT. In this paper, the performance of a non-toroidal shape protection CT is studied. The research is focused on the cable position influence in possible partial saturations of the CT when it is operating near to its accuracy limit. Depending on the cable position, the ratio of the primary and secondary currents can depart from assigned ratio. The validation of this phenomenon has been carried out via Finite Element Analysis (FEA) showing that partial transformer core saturations appears in areas of the magnetic core close to the cable. Applying FEA, also the admissible accuracy region for cable positioning inside the CT is delimited. Finally, the simulation results are ratified with experimental tests performed in non-toroidal protection CTs varying the primary cables’ positions, which are subjected to currents up to 5 kA, achieving satisfactory results. From this analysis, installation recommendations are given.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

The infrared (IR) satellite remote sensing of sea surface skin temperature (SSTskin) is challenging in the northern high latitude region, especially in the Arctic because of its extreme environmental conditions, and thus the accuracy of SSTskin retrievals is questionable. Several Saildrone uncrewed surface vehicles were deployed at the Pacific side of the Arctic in 2019, and two of them, SD-1036 and SD-1037, were equipped with a pair of IR pyrometers on the deck whose measurements have been shown to be useful in the derivation of SSTskin with sufficient accuracy for scientific applications, providing an opportunity to validate satellite SSTskin retrievals. This study aims to assess the accuracy of MODIS-retrieved SSTskin from both Aqua and Terra satellites by comparisons with collocated Saildrone-derived SSTskin data. The mean differences in SSTskin from the SD-1036 and SD-1037 measurements are different by ~0.4 K, largely resulting from differences in the atmospheric conditions experienced by the two Saildrones. The performance of MODIS on Aqua and Terra in retrieving SSTskin is comparable. Negative brightness temperature (BT) differences between 11 μm and 12 μm channels are identified as being physically based, but are removed from the analyses as they present anomalous conditions for which the atmospheric correction algorithm is not suited. Overall, the MODIS SSTskin retrievals show negative mean biases, -0.234 K for Aqua and -0.295 K for Terra. The variations in the retrieval inaccuracies show an association with diurnal warming events in the upper ocean from long periods of sunlight in the Arctic. Also contributing to inaccuracies in the retrieval is the surface emissivity effect in BT differences characterized by the Emissivity-introduced BT difference (EΔBT) index. This study demonstrates the characteristics of MODIS-retrieved SSTskin in the Arctic, at least at the Pacific side, and underscores that more in situ SSTskin data at high latitudes are needed for further error identification and algorithm development of IR SSTskin.

The study investigated the usage of open data in public organizations, focusing on the motives, preferences, and governance ideals that determine their quality. The study shed light on how open data platforms are created and improved, as well as their influence on government operations. The primary goal was to understand the motivations behind the usage of open data, evaluate gov-ernance ideals, and examine institutions' efforts to standardize data formats. Hierarchical regres-sion analysis divides variables into core reasons and different preferences, demonstrating a need for "diversification" in order to use open data effectively. Efficiency, accountability, community impact, knowledge, and high-quality service delivery are all emphasized in governance value analysis. The institution's dedication to standardizing open data formats is evidenced by legislative measures and the integration of many technologies. The findings illustrate the institution's dual strategy of em-ploying traditional techniques and new technologies for effective data management. The report suggests increasing data openness and standardization, investing in ongoing training, upgrading alerting and awareness systems, and adopting specific regulations for open data use. Monitoring and feedback techniques are critical for adjusting and refining open data services to satisfy de-velopment needs. This study adds to the scientific knowledge of open data use by highlighting important motives, preferences, and governance ideals. The offered guidelines provide practical insights for public organizations looking to improve their open data platforms by promoting openness, efficiency, and community participation.

Rice (Oryza spp.) is mostly grown directly from seed and sown on wet or dry seed beds or usually used as transplants on nursery bed. With all the economically important viral diseases in the world, Rice yellow mottle virus (RYMV), is only prevalent in rice-growing countries in Africa. RYMV had turned out to be the main rice production constraint in Africa, throughout the last 20–25 years, causing yield loss of 10 to 100%, depending on age of the plant at the time of infection, degree of varietal susceptibility and the exiting climatic conditions. Good agricultural practices and utilization of biotechnological tools in the development of improved resistant cultivars have been extensively active in controlling the disease. This review focused on RYMV, its epidemiology, serological and molecular typing, disease management and the way forward for sustainable rice production.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

Plants are subjected to abiotic stresses throughout their developmental period. Abiotic stresses include drought, salt, heat, cold, heavy metals, nutritional element and oxidative stresses. Improving plant response to various environmental stresses is critical for plant survival and perpetuation. The WRKY transcription factors have special structure (WRKY structural domains), which enable WRKY transcription factors to have different transcriptional regulatory functions. The WRKY transcription factors can not only regulate abiotic stresses response and plant growth and development by regulating phytohormone signalling pathways, but also promote or suppress the expression of downstream genes by binding to the W-box [TGACCA/TGACCT] in the promoters of their target genes. In addition, WRKY transcription factors not only interact with other families of transcription factors to regulate plant defence responses in abiotic stresses, but also self-regulate by recognizing and binding to W-boxes in their own target genes to regulate their defence responses to abiotic stresses. However, in recent years, research reviews on the regulatory roles of WRKY transcription factors in higher plants are scarce and shallow. In this review, we focus on the structure and classification of WRKY transcription factors, as well as the identification of their downstream target genes and molecular mechanisms involved in the response to abiotic stresses, which can improve the tolerance ability of plants in abiotic stress and we also look forward to their future research directions, with a view to providing theoretical support for the genetic improvement of crop abiotic stresses tolerance.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Ethiopian Airlines is a leading airline in the world. Its supply chain management is one of the most critical aspects in achieving its sustainability objectives. The present study aims to assess the sustainability practices and strategies of Ethiopian Airways in its supply chain, identifying areas for improvement and recommending strategies for enhancing sustainability. The study concentrates on pertinent sustainability concerns within the aviation sector while examining antecedent research on the sustainability of Ethiopian Airlines’ supply chain management strategies. The findings of the study reveal that there are several areas in need of improvement, including the implementation of waste reduction measures, the establishment of a recycling program, and the reduction of single-use plastic usage. It is suggested that promoting responsible tourism embodying sustainable practices is imperative, particularly within the airline context.

Maize is the staple cereal in Malawi, with a daily per capita consumption of 383g (dry matter basis), primarily consumed as dehulled maize flour used to cook nsima, a thick porridge. However, the extent of mass and nutrient loss during dehulling remains unclear in this food-insecure country, where the household maize harvest typically lasts only 6–7 months. In the current study, a milling experiment to determine yield and micronutrient losses was conducted. Milling batches (30 kg) of four maize grain varieties were dehulled at three abrasive disk dehullers under controlled conditions. Mass losses ranged from 18.8% to 42.7%, with a mean of 28.2±5.7%. Maize variety and dehuller significantly affected mass loss (p<0.05). Initial protein, iron, and zinc concentrations were 8.8 ±1.0 g/100g, 20.5±2.0 µg/g, and 18.2 ±2.6 µg/g, respectively. Post-dehulling nutrient true retention varied for protein (49.7% to 75.6%, mean=64.7±7.0%), iron (18.7% to 71.6%, mean=37.6±12.0 %), and zinc (11.0% to 46.2%, mean=27.9±8.7 %). Maize variety significantly influenced mass and protein loss (p < 0.05), while dehuller influenced mass, iron, and zinc losses. However, no significant difference (p > 0.05) was found in the interaction between dehullers and variety on mass and nutrient losses, respectively. Given Malawi's precarious food insecurity situation, transitioning from dehulled maize flour nsima to whole maize flour or less refined nsima, is imperative. Our study findings can have food and nutritional savings for other southern Africa countries where the dehulling practice is rampant.

The concept of economic self-reliance, widely known by Thai people as the philosophy of sufficiency economy, has been widely promoted in rural Thai societies. By practicing this philosophy, it is expected that the citizens’ quality of life and local environments could be sustainably improved. This study aims to explore the contribution of the community practices of the sufficiency economy philosophy to rural villagers’ quality of life improvement, and to investigate potential factors that determine the trust of villagers in the philosophy. With the purpose to propose strategies which could enhance trust and promote villagers’ practices of the philosophy, the study investigated influences of three relevant factors on trust towards the philosophy. Those factors included factors related to cognitive-based trust, factors related to emotional-based trust, and factors related to demographic characteristics. Questionnaire surveys and in-depth interviews with community leaders and local villagers were conducted in the Ban Jamrung community, in Thailand’s Rayong province. The results of the statistical analysis revealed that the residents who applied the sufficiency economy philosophy in their daily lives experienced a relatively better quality of life. Additionally, it was found that trust in the philosophy could be predicted more by rational factors than by emotional factors. These findings could be utilized to develop strategies to maintain and enhance the trust of the people in the philosophy of sufficiency economy.

Accurate forecasting of crop yields holds paramount importance in guiding decision-making processes related to breeding efforts. This study focused on the application of multi-sensor data fusion and machine learning algorithms based on unmanned aerial vehicles (UAVs) in wheat yield prediction. Five machine learning (ML) algorithms namely random forest (RF), partial least squares (PLS), ridge regression (RR), K-Nearest Neighbor (KNN) and eXtreme Gradient Boosting Decision Tree (XGboost) were utilized for multi-sensor data fusion, and three ensemble methods including the second-level ensemble methods (stacking and feature-weighted) and the third-level ensemble method (simple average) for wheat yield prediction. The 270 wheat hybrids were used as planting materials under full and limited irrigation treatments. A cost-effective multi-sensor UAV platform, equipped with red–green–blue (RGB), multispectral (MS), and thermal infrared (TIR) sensors, was utilized to gather remote sensing data. The results revealed that the XGboost algorithm exhibited outstanding performance in multi-sensor data fusion, with the RGB+MS+Texture+TIR combination demonstrating the highest fusion performance (R2=0.660, RMSE= 0.754). Compared with the single ML model, the employment of three ensemble methods significantly enhanced the prediction accuracy of wheat yield. Notably, the third-layer simple average ensemble method demonstrated superior performance (R2 = 0.733, RMSE= 0.668 t ha-1). It significantly outperformed both the second-layer ensemble methods of Stacking (R2= 0.668, RMSE= 0.673 t ha-1) and feature-weighted (R2= 0.667, RMSE= 0.674 t ha-1), thereby exhibiting superior predictive capabilities. This finding demonstrated that the third-layer ensemble method not only augments the predictive ability of the model but also fine-tuned the accuracy of wheat yield prediction through the employment of simple average ensemble learning. Consequently, it offers a novel perspective for crop yield prediction and breeding selection.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Grain quality, cooking quality and nutritional quality traits are some of the major attributes that enhance uptake and utilisation of improved cowpea varieties. Therefore, there is need for a better understanding of the genetic variation and inter-relationships among these quality traits in cowpea to integrate them in cowpea breeding programs. The study was conducted to determine genetic variability among 306 cowpea genotypes for grain quality, cooking quality and nutritional quality traits and to understand the interrelationships among these traits for exploitation in breeding programs. The results showed highly significant differences (P

Background: Low back pain (LBP) is a major cause of disability globally, and the diagnosis of LBP is challenging for clinicians. Objective: This study aimed to assess the accuracy level of arti-ficial intelligence as a Clinical Decision Support System (CDSS) called Therapa compared to MRI in predicting lumbar disc herniated patients. Methods: One hundred low back pain patients aged ≥18 years old were included in the study. The study was conducted in 3 stages, at first, a case se-ries was conducted by matching MRI and Therapha diagnosis for 10 patients. Subsequently, Delphi methodology was employed to establish a clinical consensus. Lastly, to determine the ac-curacy of the newly developed software, a cross-sectional study was undertaken, involving 100 patients. Results: The software showed a significant diagnostic accuracy with the area under the curve in the ROC analysis determined as 0.84 with a sensitivity of 88% and a specificity of 80%. Conclusion: The study’s findings revealed that CDSS using Therapha has a reasonable level of ef-ficacy, and this can be utilized clinically to acquire faster and more accurate screening of patients with lumbar disc herniation.

(1) Background: To determine the diagnostic accuracy that optical coherence tomography (OCT) can add to fundus photography (FP) in assessing the condition of the retinal posterior pole; (2) Methods: Two blocks of analysis: at first, the posterior pole of each eye was examined using FP non-mydriatic imaging device. Secondly: OCT was used in addition to FP. After consolidating specific diagnostic criteria, the assessments were evaluated by two blinded independent investigation groups (by optometrists, and by ophthalmologists who was considered the gold standard); (3) Results: We calculated the diagnostic accuracy of FP compared to OCT and found that both had similar sensitivity, FP had slightly higher specificity, (p-value: 0.01) and OCT had a higher kappa coefficient 0.50 (95%CI: 0.46-0.55) vs 0.39 (95%CI: 0.34-0.45) of FP; (4) Conclusions: Based on the premise that the role of the optometrist in Spain is not to diagnose but to detect lesions and refer patients to an ophthalmologist, the results of this study support the use of OCT, that it provided gradable images in almost all examined eyes (97.5%), compared to FP (73.5%). However, the optometrist need a detailed and standardized guide in order to evaluate according to the ophthalmologist's criteria.

External motivational stimuli have been shown to improve athletic performance. However, the neurophysiological mechanisms underlying this improvement remain poorly understood. This randomized crossover study investigated the effects of music and verbal encouragement on measures of muscle excitation and myoelectric manifestations of fatigue in the biceps brachii (BB) and brachioradialis (BR) muscles during an endurance task. Fifteen untrained (mean age 29.57 ± 2.77 years) and 13 trained individuals (mean age 32.92 ± 2.90 years) were included. The endurance task, performed to exhaustion, consisted of keeping the dominant arm flexed to 90 degrees while holding a dumbbell loaded to 80% of 1RM with a supine grip in three randomized conditions: standard, with self-selected music, and with verbal encouragement. The untrained subjects showed an increase in task duration of 15.26% (p < 0.003) with music and 15.85% (p < 0.002) with verbal encouragement compared to the condition without external stimuli. There were no significant differences in the myoelectric manifestations of fatigue between the dif-ferent conditions. Regarding the muscle excitation metrics, although the mean amplitude, peak value and area under the curve remained unchanged across conditions, a significant reduction in the trend coefficient, indicating motor unit recruitment over time, was observed with both music (BB: -10.39%, p < 0.001; BR: -9.40%, p < 0.001) and verbal encouragement (BB: -7.61%, p < 0.001; BR: -6.51%, p < 0.001) compared to the standard condition. For the trained participants, no significant differences were observed between conditions in terms of task duration and outcome measures related to muscle excitation and myoelectric manifestations of fatigue, suggesting the possible presence of a ceiling effect on motivation. These results highlight the significant role of external motivational stimuli, such as music and verbal encouragement, in improving task performance in untrained subjects, probably through more ef-fective and efficient recruitment of motor units.

Background: Visual acuity (VA) assessments are crucial in ophthalmology but traditionally rely on in-clinic evaluations. The emergence of telemedicine has spurred interest in creating dependable self-administered VA tests for use beyond standard clinical environments. This study evaluates the practicality and validity of a self-administered Near VA card test against traditional Snellen and Rosenbaum Pocket Vision Screener (RPVS) methods for home monitoring and enhancing clinical workflow. Methods: In a cross-sectional study a near VA card (Hadassah Self-Visual Acuity Screener-HSVA) was developed with written and videotaped instructions for self-use. Patients with a minimal best corrected VA (BCVA) of 1.0 LogMAR in at least one eye were recruited from Ophthalmology and Optometry clinics. Outcomes included mean BCVA difference between the self-administered and those obtained by the examiner, and correlations among BCVA values obtained by Snellen, RPVS, HSVA and previous distance BCVA according to the patient electronic medical records. Results: A total of 275 participants (mean age: 42.5±19.4 years, range: 18-89 years, 47% female) were included. Test-retest reliability analysis for the HSVA demonstrated very good correlation and repeatability (n=38 patients.; Rs=1.0, P

Introduction: Biliary Atresia (BA) is a common cause of neonatal cholestatic jaundice which, if recognized and treated early, can be life-saving for the infant. If the liver biopsy suggests the presence of BA, exploratory laparotomy is then carried out to confirm the diagnosis, along with the Kasai procedure to provide drainage to the bile secreted by the liver. The purpose of this study is to get a deep dive into all the various imaging modalities that can diagnose BA more effectively and with absolute certitude, thus helping prevent several children from a grave prognosis.Methodology: For the collection of the data, a search was done by two individuals using PubMed, Google Scholar, and Cochrane Library databases for all relevant literature. Each qualifying paper was evaluated independently by two reviewers. Each article was analyzed for the number of patients, their age, procedure modality, complexity of ethology, and incidence of the pre-decided complications. The statistical software packages RevMan (Review Manager, version 5.3), SPSS (Statistical Package for the Social Sciences, version 20), Google Sheets, and Excel in Stata 14 were used to perform the statistical analyses. The data was obtained and entered into analytic software.Results: A total of 39 studies with 3,679 subjects were selected for the study, out of which 7 studies showed sensitivity above or equal to 95%, and an astounding 14 studies showed specificity above 95%. The value of True Positive (TP) was 1280, that of True Negative (TN) was 1817, that of False Positive (FP) was 239, and that of False Negative (FN) was 343. With a confidence interval of 95%, sensitivity, specificity, and positive predictive values were calculated. The sensitivity of Ultrasonography for Biliary Atresia is 0.79, with a CI of 95% in a range of 0.77 to 0.81. The specificity of Ultrasonography for Biliary Atresia is 0.88, with a CI of 95% in a range of 0.87 to 0.90. Conclusion: Even though several radiological techniques at present help to detect BA, USG of the abdomen proves to be an effective diagnostic and a modest screening test for the detection of BA.

A method for estimating river water surface elevation (WSE) from Landsat imagery using the river inundation area - water surface elevation (RIA-WSE) rating curve constructed from the U.S. Geological Survey Topobathymetric Elevation Model (TEM) data was developed and tested at six gauging stations along the upper Mississippi River. The Otsu's automatic threshold selection algorithm was employed for the image classification and estimation of inundation areas within each pre-defined polygon around each gauging station. In addition to the commonly used green-band based water indices, Landsat 8 and 9 OLI's ultra-blue, blue, and red band-based water indices were also tested in this study, which resulted in twenty different water indices: NDWIv (Normalized Difference Water Index), MNDWI1v and MNDWI2v (Modified Normalized Difference Water Index), AWEIsv (Automatic Water Extraction Index with shadow), and AWEInsv (AWEI without shadow), where v represents the visible light band used in the water index. At each station, about 60-80 Landsat 8 or 9 images during 2013-2023 were used for assessing the performances of the twenty water indices through comparing the estimated WSEs with the measured WSEs. Results showed that the ultra-blue or red band-based AWEIs yielded the most accurate estimations of WSEs among the twenty tested water indices.

We conducted a study to determine if antenatally collected maternal urine cotinine (a me- 13 tabolite of nicotine) measurements can be used to assess the neonatal impact of nicotine exposure 14 during pregnancy. This was a prospective longitudinal cohort of mother-infant dyads. Only term 15 singleton pregnancies were included. The primary outcome measure was the correlation between 16 maternal urine cotinine and infant birth weight. We analysed data from 238 mother-neonates' dy- 17 ads. Urine cotinine was detected in 50.4 % (120/238) women from the whole cohort, but only 16% 18 (38/238) self-reported as smokers (chi-square 39.7, p<0.0001), and these women had significantly 19 smaller babies (p=0.010). There was a significant negative correlation between maternal urine co- 20 tinine and birth weight (Spearman's coefficient = -0.0226, p=0.013). Female babies born to women 21 with nicotine in the urine were significantly smaller (p= 0.001). The number of women exposed to 22 nicotine during late pregnancy (measured in urine) was markedly higher than self-reported and 23 National smoking percentages, suggesting an urgent need for improvement of medical record re- 24 porting on smoking habits to better assess neonatal outcomes.

This study aimed to enhance the compatibility of glass ionomer cement (GIC) with tooth tissue by chemically modifying its primary component, calciumfluoroaluminosilicate (CFAS), through the incorporation of nanorod hydroxyapatite (nHA). The process involved binding L-glutamic acid to nHA, followed by activation and binding of albumin to create nHA immobilized with albumin. This modified nHA was then used to surface-modify CFAS particles, producing nHA-CFAS powder. The modified powder was mixed with poly(acrylic acid) and UV-cured to form GIC containing nHA-CFAS (GIC-nHA). Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) confirmed the successful modification. Cytocompatibility tests with osteoblasts showed that GIC-nHA had superior cell viability and bone formation capabilities compared to the control GIC. The improved histocompatibility is attributed to nHA enhancing the biological activity of osteoblasts, indicating that the surface modification method significantly improves the functional integration of GIC with tooth tissue.

This paper proposes an optimization method for the scheduling of a multi-energy virtual power plant supply-demand balance in the power market environment of Jiangxi Province. The objective of this method is to enhance the operational efficiency of the power grid, reduce energy costs, and facilitate economical and efficient energy distribution in the power market. The method comprehensively considers the characteristics and uncertainties of renewable energy sources such as solar and wind energy, and incorporates advanced multi-objective optimization algorithms. Additionally, real-time market price feedback is integrated to achieve accurate allocation of power supply and demand. Through a case study of a multi-energy virtual power plant in Jiangxi Province, this paper examines the optimal combination model for various energy sources within VPP, and analyzes the impact of different market environments on supply-demand balance. The results demonstrate that the proposed scheduling optimization method significantly improves economic benefits while ensuring grid stability. Compared with traditional power supply models, it reduces average electricity costs by 15% and increases renewable energy utilization efficiency by 20%.

The Geopyörä breakage test uses two counter-rotating wheels to nip and crush rock specimens with a tightly controlled gap between rollers. The force applied and energy consumed during breakage are measured with instrumentation. In contrast to drop weigh test (DWT) methods, the breakage energy is a response to the rock compressive strength and degree of compression, not a controlled test input, such as the kinetic input energy of a falling weight. This paper presents the detailed measures conducted to evaluate the accuracy and precision of energy measurements across various ore types using the Geopyörä device. While force measurement was assessed just for its precision. The outputs are compared directly to the DWT measures of fragmentation at the same energy and fitted A and b parameters. The test reproducibility was evaluated using a Round-Robin methodology, testing several samples in multiple laboratories. The results confirmed that the new test has sufficient accuracy to match DWT results and excellent precision to assure reproducibility.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

Lactoperoxidase system (LPS) effect on quality of raw and pasteurized milk under real conditions along the dairy value chain in Ethiopia was evaluated. A total of 250 milk samples were collected from farmers, collectors, and factories. Experimental samples were LPS-activated of morning and overnight milk. The samples were tested with several chemical and microbiological tests such as total bacterial count (TBC), total coliform count (TCC) and Escherichia coli count (EC). Results indicated that all LPS-activated milk samples had a higher quality than all the control samples. For instance, both the morning and overnight farm milk samples had a mean TBCs of 5.79 log and 6.55 log cfu/ml which is significantly (p

Augmented and Virtual Reality have been experiencing a rapidly growth in recent years, but there is not still a deep knowledge on their capabilities and where they could be explored. In that sense, this paper presents a study on the accuracy and repeatability of the Microsoft's HoloLens 2 (Augmented Reality device) and HTC Vive (Virtual Reality device) using an OptiTrack system as ground truth. For the HoloLens 2, the method used was hand tracking, while in HTC Vive, the object tracked was the system's hand controller. A series of tests in different scenarios and situations were performed to explore what could influence the measures. The HTC Vive obtained results in the millimetre scale, while the HoloLens 2 revealed not so accurate measures (around 2 centimetres). Although the difference can seem to be considerable, the fact that HoloLens 2 was tracking the user's hand and not an inherit controller made a huge impact. The results were considered a significant step for the on going project of developing a human-robot interface to program by demonstration an industrial robot using Extended Reality, which shows great potential to succeed based on this data.

We present a design of electrostatic comb driver to improve and investigate its actuation performance. The proposed electrostatic comb actuator (ECA) is composed of two set of interdigitated comb microstructures, the inner combs are fixed to form the fish-bone microstructures and the outer combs are movable and connected to crab-leg flexure beams microstructures. The ECA is investigated to optimize the actuation performance by changing the comb shape and the intersection angle of crab-leg flexure beams. The comb shapes are compared between the traditional rectangle shape and the trapezoid shape, while the intersection angles of crab-leg flexure beams are compared between 45°, 60°, and 90° on the influences of ECA displacement and stability characteristics. These parameters are investigated for their impacts on the dynamic comb displacement and driving voltage. Under the condition of a driving DC bias voltage of 100 volts, the ECA displacement is firstly increased and then gradually decreased by increasing the comb finger length. The maximum displacement of ECA with trapezoid comb is 47.2 μm while that of ECA with rectangle comb is 22.4 μm. By using trapezoid comb shape to replace the rectangle comb under the same conditions, the ECA displacement is improved 2-fold. To enhance the stability of ECA system, the intersection angle of 90˚ of crab-leg flexure beams shows highest stability that is great better than the intersection angle of 45° and 60° of crab-leg flexure beams by increasing the driving different DC bias voltage to 100 volts on ECA. The stability of the ECA with the intersection angle of 90° of crab-leg flexure beams is enhanced 1.1-fold and 1.4-fold compared to that of 45° and 60° of crab-leg flexure beams, respectively. This design provides an optimized approach to the electrostatic comb actuator that can be used expansively in the gyroscope, motion sensor, position sensor, imaging sensor, optical sensor, and so on.

Lessons learned and risk-based outcomes from modernising the Australian Standard for post-mortem inspection and disposition judgement of beef, sheep, goat and pig carcases are described. Initial Risk Profiles identified priorities for quantitative assessments. The main difficulty encountered was the paucity of quantified performance of current inspection. Resolving this involved acquiring gross abnormality data representing regional production/proportional abattoir volumes, the range of gross abnormalities appearing nationally, proportional occurrence at carcase sites, and seasonality to enable comparisons. Evidence and discussion are provided for associated challenges experienced including preventing contamination, use of food chain information to support amendment, inspection as a part of industry Quality Assurance and opportunities to improve inspector training. Criteria considered by the Competent Authority for determination of equivalence of alternative post-mortem inspection techniques included comparisons of public health risk, non-detection rates for gross abnormalities, and microbial contamination resulting from inspection activities, as appropriate. Most gross abnormalities detected arose from animal health and welfare conditions affecting wholesomeness and did not present as food safety hazards. Non-detection rates between current and alternative inspection (observation) were negligible. A Quantitative Risk Assessment for Cysticercus bovis was conducted. Carcases with multiple gross abnormalities predominantly reflected historic infections (prior septicaemia) where trimming achieved wholesomeness unless cachexic.

Spatial light modulators (SLMs) have been widely used to achieve dynamic control of optical traps. Often, holographic optical tweezers have been presumed to provide nanometer or sub-nanometer positioning accuracy. It is known that some features concerning the digitalized structure of SLMs cause a loss in steering efficiency of the optical trap, but their effect on trap positioning accuracy has been scarcely analyzed. On the one hand, the SLM look-up-table, which we found to depend on laser power, produces positioning deviations when the trap is moved at the micron scale. On the other hand, phase quantization, which makes linear phase gratings become phase staircase profiles, leads to unexpected local errors in the steering angle. We have tracked optically-trapped microspheres with sub-nanometer accuracy to study the effects on trap positioning, which can be as high as 2 nm in certain cases. We have also implemented a correction strategy that enabled the reduction of errors down to 0.3 nm.

Saliva, as a diagnostic medium, offers a promising alternative to blood by virtue of its non-invasive collection, which enhances patient compliance, especially in paediatric and geriatric populations. In this study, we assessed the utility of saliva as a non-invasive medium for measuring V. cholerae-specific serum antibodies in naturally infected individuals. We tested paired serum and saliva samples obtained from a total of 63 cholera patients enrolled in a cohort study. Vibriocidal antibodies assay (IgM/IgG) as markers for accurate determination was used to determine cholera specific antibody levels. Using receiver operating characteristics (ROC) curve, we found that the best cut-off that maximizes (sensitivity + specificity) is 10 titers. At this saliva titer, the sensitivity is 76.9% (95%CI: 60.9%, 87.7%) and specificity is 80.0% (95%CI: 56.6%, 92.5%). Using Spearman’s correlation coefficient, we also found evidence of a positive correlation between Vibrio Cholerae saliva and serum antibodies (rho=0.66, p&lt;0.001). In conclusion, saliva-based diagnostic cholera tests has high diagnostic accuracy, and would be advantageous, cheaper, and quicker for early diagnosis of severe cholera outcomes.

The presence of anti SARS-CoV2-RBD antibody (Anti-RBD) prevents severe COVID-19. We aimed to determine the accuracy of a point-of-care Anti-RBD test implemented in person living with HIV (PLWH), systemic lupus erythematosus (SLE), and chronic kidney disease (CKD). We enrolled 182 non-comorbid subjects and 335 persons with comorbid (PLWH, SLE, CKD) to test anti-RBD assay compared to surrogate viral neutralization (SVNT) as the reference test. We performed linear correlation analysis between anti-RBD vs SVNT and a ROC analyses to ascertain anti-RBD cut-off at 30%, 60%, and 90% inhibition of SVNT to calculate accuracy. Correlations of anti-RBD to SVNT among all groups were excellent with R= 0.7903, R=0.7843, R=0.8153 among non-comorbid, SLE and CKD groups, respectively, with significantly higher correlation among the PLWH group (R=0.8877; p-value=0.0072) compared to non-comorbid group. The accuracy of the anti-RBD test among PLWH and CKD group was similar with the non-comorbid but showed lower sensitivity in the SLE group (p=0.000014). The specificity of the test remained high in all groups. In conclusion, the Anti-RBD test had excellent correlation to SVNT. The persistently high specificity in all groups suggests that this test can be reliably utilized to detect presence of low neutralization capacity, prompting additional vaccination.

Objectives: To rate the effects of low molecular weight hyaluronic acid (LMWHA) solution and high concentration oxygen (HCO) through a specific medical device (Caress Flow©), compared to topical administration of hyaluronic acid (HA) alone on symptoms of mild and moderate stress and mixed urinary incontinence in women with genitourinary syndrome of menopause (GSM). Methods: A total of 68 postmenopausal women were enrolled (from October 2021 to September 2023). Patients were separated in two groups: one group used therapy with LMWHA solution and HCO combined and the second group used therapy with HA alone. Patient Global Impres-sion of Improvement (PGI-I) as the first outcome was used. As secondary outcomes International Consultation on Incontinence Questionnaire - short form (ICIQ-SF) questionnaire and Internation-al Quality of Life (IQoL) questionnaire were used. Results: Sixty-eight (68) women, 35 (51%) and 33 (49%), were treated with LMWHA solution and HCO combined and HA alone for 10 weeks, respectively. 28 (80%) versus 7 (20%) women reported an improvement (PGI-I score ≤3) of the symptoms in LMWHA solution and HCO com-bined group versus HA alone group. According to the ICIQ-SF, a statistically significant differ-ence was recorded after treatment between the two groups (median, 7 [5-11] vs 10 [8-11]; P = 0.03). According to the IQoL questionnaire, a statistically significantly lower median score was recorded in the LMWHA solution and HCO combined compared with the HA group, before (71 [IQR 55-81] vs 89 [IQR 67-94]; P < 0.01) and after (78 [IQR 65-86] vs 88 [IQR 72-99]; P = 0.04) treatment. Conclusions: LMWHA solution and HCO combined might improve the mild and moderate stress and mixed urinary incontinence in this set of women and that it is superior to HA therapy alone. However, these results need to be confirmed in further studies with a controlled design and a larger population.

Wheat (Triticum aestivum L.) breeding programs can take over a decade to release a new variety. However, new methods of selection such as genomic selection (GS) must be integrated to decrease the time it takes to release new varieties to meet the demand of a growing population. The implementation of GS into breeding programs is still being explored, with many studies showing its potential to change wheat breeding through achieving higher genetic gain. In this review, we explore the integration of GS for a wheat breeding program by redesigning the traditional breeding pipeline to implement GS. We propose implementing a two-part breeding strategy by differentiating between population improvement and product development. The implementation of GS in the product development pipeline can be integrated into most stages and can predict within and across breeding cycles. Additionally, we explore optimizing the population improvement strategy through GS recurrent selection schemes to reduce crossing cycle time and significantly increase genetic gain. The recurrent selection schemes can be optimized for parental selection, maintenance of genetic variation, and optimal cross-prediction. Overall, we outline the ability to increase the genetic gain of a breeding program by implementing GS and a two-part breeding strategy.

Reliable methods to confirm the diagnosis of COVID-19 are essential to the successful management and containment of the virus. Current diagnostic options are limited in type, supply, and reliability. This article explores the controversial unreliability of existing diagnostic methods and maintains that more reliable diagnostic methods, combinations, and sequencing are necessary to effectively assist in reducing the occurrence of discharge of the patient on false negative test results. This reduction would in effect reduce transmission of the disease.

The Earth’s synthetic gravitational and density models can be used to validate numerical procedures applied for a global (or large-scale regional) gravimetric forward and inverse modelling. Since the Earth’s lithospheric structure is better constrained by tomographic surveys than a deep mantle, most of existing 3-D density models describe only a lithospheric density structure, while 1-D density models are typically used to describe a deep mantle density structure below the lithosphere-asthenosphere boundary. The accuracy of currently available lithospheric density models is examined in this study. The error analysis is established to assess the accuracy of modelling the sub-lithospheric mantle geoid, while focusing on the largest errors (according to our estimates) that are attributed to lithospheric thickness and lithospheric mantle density uncertainties. Since a forward modelling of the sub-lithospheric mantle geoid comprises also numerical procedures of adding and subtracting gravitational contributions of similar density structures, the error propagation is derived for actual rather than random errors (that are described by the Gauss’ error propagation law). Possible systematic errors then either lessen or sum up after applying particular corrections to a geoidal geometry that are attributed to individual lithospheric density structures (such as sediments) or density interfaces (such as a Moho density contrast). The analysis indicates that errors in modelling of the sub-lithospheric mantle geoid attributed to lithospheric thickness and lithospheric mantle density uncertainties could reach several hundreds of meters, particularly at locations with the largest lithospheric thickness under cratonic formations. This numerical finding is important for a calibration and further development of synthetic density models of which mass equals the Earth’s total mass (excluding the atmosphere). Consequently, the (long-to-medium wavelength) gravitational field generated by a synthetic density model should closely agree with the Earth’s gravitational field.

Chi-squared automatic interaction detector (CHAID) algorithm is considered to be one of the mostly used supervised learning methods as it is adaptable to solving any kind of problem at hand. We have been starkly aware of CHAID maps non-linear relationships quite well, and it can empower predictive models with stability. But we don’t know how high its accuracy is precisely. To find out the perfect scope CHAID algorithm fits into, this paper presents the analysis of the accuracy of the CHAID algorithm. We introduce the causes, applicable conditions and application scope of CHAID algorithm at first, and then highlight the difference of branching principal between the CHAID algorithm and several other common decision tree algorithms, which is our first step towards basic analysis on CHAID algorithm. We next employee an actual branching case to help us understand CHAID algorithm better. Specifically, we use vehicle customer satisfaction data to compare multiple decision tree algorithms, and cite some factors that affecting the accuracy and some corresponding countermeasures which are more conducive to us to obtain accurate results. The results show that CHAID can analyze the data very well, and detect the significantly correlated factors surely. In this paper, we learn the clear information required to understand CHAID algorithm, thereby make better choices when we need to use decision tree algorithms.

The objective of this work was to investigate the use of remotely sensed vegetation indices to improve the quality of yield maps. The method was applied to the yield data of twelve cornfields from the Data Intensive Farm Management project. The results revealed the need to time shift the yield values up to three seconds to better match the sensor readings with the geographic coordinates. The residuals of the yield prediction model were used to identify points with unlikely yield values for that location, as an alternative to traditional approaches using local spatial statistics, without any assumption of spatial dependence or stationarity. The temporal and spatial distribution of the standardized coefficients for each experimental unit highlighted the presence of trends in the data. At least five out of the twelve fields presented trends that could have been induced by data collection.

Molecular markers, including Simple Sequence Repeat (SSR), Single Nucleotide Polymorphism (SNP), and Intron Length Polymorphism (ILP), are widely utilized in crop improvement and population genetics studies. However, these marker resources remain insufficient for Musa species. In this study, we developed genome-wide SSR, SNP, and ILP markers from Musa and its sister species, creating a comprehensive molecular marker repository for the improvement of Musa species. This database contains 2115474 SSR, 63588 SNP, and 91547 ILP markers developed from thirteen Musa species and two of its relative species. We found that 77% of the SSR loci are suitable for marker development; 38% of SNP markers originated from the genic region, and transition mutations (C↔T; A↔G) were more frequent than transversion. The database is freely accessible and follows a ‘three-tier architecture,’ organizing marker information in MySQL tables. It has a user-friendly interface, written in JavaScript, PHP, and HTML code. Users can employ flexible search parameters, including marker location in the chromosome, transferability, polymorphism, and functional annotation, among others. These distinctive features distinguish the Musa Marker Database (MMdb) from existing marker databases by offering a novel approach that is tailored to the precise needs of the Musa research community. Despite being an in silico method, searching for markers based on various attributes holds promise for Musa research. These markers serve various purposes, including germplasm characterization, gene discovery, population structure analysis, and QTL mapping.

Currently, electromagnetic and radar methods are the most common non-destructive tests for non-destructive rebar location in structures.. Both methods have some advantages, disadvantages and limitations. This article is an attempt to describe possibilities of particular methods with emphasizing their advantages and limitations. The first stage of tests included results from tests conducted on a lintel beam made of autoclaved aerated concrete (AAC) and reinforced with small-diameter rebars and rebars placed close to each other. The second stage consisted in testing nine lightweight concrete specimens, each with three bars having a diameter of 10, 16 and 20 mm at three different space arrangements, to determine the effect of bar diameter and spacing on the measurement accuracy. The reinforcement of lintels and specimens was tested with two different electromagnetic scanners and a ground-penetrating radar (GPR) device. Received results from direct tests were compared with results from non-destructive tests (NDT). NDT tests conducted in such an element were found to perform the correct assessment of the concrete cover, and at the same time to give ambiguous results with reference to shape and number of rebars.

We estimate general public’s willingness to pay (WTP) for agricultural soil quality protection and improvement in Spain (n=1000) and the UK (n=984) using data from a cross-sectional survey via Qualtrics panels in March-April 2021. We use a double bound dichotomous choice contingent valuation approach to elicit the individuals’ WTP. We investigate the effect of uncertainty on the success of policies aiming at achieving soil protection. In addition, to understand the heterogeneity in individuals’ WTP for agricultural soil quality protection and improvement we model individuals’ WTP through individual’s awareness and attitudes toward agricultural soil quality protection and the environment, trust in institutions; risk and time preferences; pro-social behavior and socio-demographics in Spain and the UK. We found that there is significant public support for agricultural soil quality protection and improvement in Spain and the UK. We also found that the support does not vary significantly under uncertainty of success of policies aiming at achieving soil protection. However the individual’s reasons for supporting agricultural soil quality protection and improvement are found to depend on the level of uncertainty and country. Hence, promoting public support for soil protection needs to be tailored according to the level of general public’s perceived uncertainty and geographic location.

Alternative splicing (AS) is a gene regulatory mechanism modulating gene expression in multiple ways. AS is prevalent in all eukaryotes including plants. AS generates two or more mRNAs from the precursor mRNA (pre-mRNA) to regulate transcriptome complexity and proteome diversity. Advances in next-generation sequencing, omics technology and bioinformatics tools, and computational methods provide new opportunities to quantify and visualize AS-based quantitative trait variation associated with plant growth, development, reproduction, and stress tolerance. Domestication, polyploidization and environmental perturbation may evolve novel splicing variants associated with agronomically beneficial traits. To date, pre-mRNAs from many genes are spliced into multiple transcripts that cause phenotypic variation for complex traits, both in model plant Arabidopsis and field crops. Cataloguing and exploiting such variation may provide new paths to enhance climate resilience, resource-use efficiency, productivity, and nutritional quality of staple food crops. This review provides insights into AS variation alongside gene expression analysis to select for novel phenotypic diversity for use in breeding programs. AS contributes to heterosis, enhances plant symbiosis (mycorrhiza and rhizobium), and provides a mechanistic link between the core clock genes and diverse environmental clues.

This paper presents high-resolution digital measurements at low cost, combining oversample and averaging. Experiments of processing data between samples and between multiple temperature sensors in the same environment are conducted. They provide results with effective increase in the analog to digital converter bits, in correspondence with the minimization on the effects of noise. It is shown that averaging a set of small, low-cost sensors at a small microcontroller can give flexible access to improved measurement accuracy.

Two of the most common activation functions (AF) in deep neural networks (DNN) training are Sigmoid and ReLU. Sigmoid was tend to be more popular the previous decades, but it was suffering with the common vanishing gradient problems. ReLU has resolved these problems by using zero gradient and not tiny values for negative weights and the value “1” for all positives. Although it significant resolves the vanishing of the gradients, it poses new issues with dying neurons of the zero values. Recent approaches for improvements are in a similar direction by just proposing variations of the AF, such as Leaky ReLU (LReLU), while maintaining the solution within the same unresolved gradient problems. In this paper, the combining of the Sigmoid and ReLU in one single function is proposed, as a way to take the advantages of the two. The experimental results demonstrate that by using the ReLU’s gradient solution on positive weights, and Sigmoid’s gradient solution on negatives, has a significant improvement on performance of training Neural Networks on image classification of diseases such as COVID-19, text and tabular data classification tasks on five different datasets.

The deep energy method (DEM), a type of physics-informed neural network, is evolving as an alternative to finite element analysis. This method employs the principle of minimum potential energy to predict deformations under static loading conditions. However, the model’s accuracy is contingent upon choosing the appropriate architecture for the model, which can be challenging due to the high interactions between hyperparameters, large search space, difficulty in identifying objective functions, and non-convex relationships with the objective functions. To improve DEM’s accuracy, we first introduce random Fourier feature (RFF) mapping. RFF mapping helps with the training of the model by reducing bias towards high frequencies. The effects of six hyperparameters are then studied under compression, tension, and bending loads in planar linear elasticity. Based on this study, a systematic automated hyperparameter optimization approach is proposed. Due to the high interaction between hyperparameters and the non-convex nature of the optimization problem, Bayesian optimization algorithms are used. The models trained using optimized hyperparameters and having Fourier feature mapping can accurately predict deflections compared to finite element analysis. Additionally, the deflections obtained for tension and compression load cases are more sensitive to variations in hyperparameters than bending.

A method of accuracy error compensation for the time interval is examined, allowing to eliminate the dependence of accuracy error on the duration of measured intervals and minimising the influence of destabilising factors - ambient temperature changes and the initial deviation of the meter clock generator frequency from the nominal value. The compensation method is based on a calibration procedure that measures precise time intervals under conditions of changing ambient temperature. Then the dependence of the accuracy error on temperature for a particular meter is recorded. Based on these data, a correction table is compiled containing correction factors and temperature values at which these factors were determined. Under real measurement conditions, the correction factor corresponding to the current temperature is determined from the table for measured results correction. The table with correction factor values could be stored in the memory of the meter or processing computer. Experimental verification of the method showed that applying a correction for a meter with a standard XO class clock generator (certificated instability of ±50 ppm) can obtain an equivalent clock generator instability of ±0.15 ppm. The application of the method is efficient in cases where the use of high-end clocking to ensure the required measurement accuracy is not economically feasible.

Determination of indoor location based on fine time measurement (FTM) of the round trip time (RTT) of a signal between an initiator (smartphone) and a responder (Wi-Fi access point) enables a number of applications. However, the accuracy currently attainable — standard deviations of 1–2 meter in distance measurement under favorable circumstances — limits the range of possible application. A first responder, for example, may not be able to unequivocally determine on which floor someone in need of help is in a multi-story building. The error in location depends on several factors, including the bandwidth of the RF signal, delay of the signal due to the high relative permittivity of construction materials, and the geometry-dependent “noise gain” of location determination. Errors in distance measurements have unusual properties that are exposed here for the first time. Improvements in accuracy depend on understanding all of these error sources. This paper introduces “frequency diversity,” a method for doubling the accuracy of indoor location determination using weighted averages of measurements with uncorrelated errors obtained in different channels. The properties of this method are verified experimentally with a range of responders. Finally, different ways of using the distance measurements to determine indoor location are discussed and the Bayesian grid update method shown to be more useful than others, given the non- Gaussian nature of the measurement errors.

This study assesses the impact of nurse-originated changes in central venous catheter (CVC) management on the incidence of central line-associated bloodstream infections (CLABSI) and catheter-related bloodstream infections (CRBSI). It is a single-center retrospective cohort study conducted at an urban, tertiary referral, and academic center serving pediatric patients. The study cohort comprised 236 patients and 323 CVCs seen between 2012 and 2022. CLABSI and CRBSI were defined according to the Centers for Disease Control and Prevention definitions. Oncology nurse leaders developed CVC-specific educational modules for CLABSI prevention. All relevant information during the CVC maintenance period was noted in the patient's CVC logbook. 24 (7%) cases of confirmed CLABSI were identified. The incidence of CVC-related infections was 0.32 cases per 1000 catheter days. The incidence decreased by 40% between the first and second three-year study period. Documented exit-site infection was reported in 32 (10%) cases. The correlation between exit-site infection and CLABSI was found in 9 (28%) cases. Our CVC-related infection rates are significantly lower than the incidence reported by the Italian Association of Pediatric Hematology and Oncology, which settles at 3-5 cases per 1000 catheter days. Our data confirm the effectiveness of local CVC management guidelines in preventing CVC-related infectious complications.

Background: Strength assessment is one of the main fields in sports performance, physical rehabilitation, physical activity and health. Purpose: To compare maximal voluntary isometric contractions (MVIC) and paired voluntary isometric contractions (VIC) of knee extensors between an isokinetic dynamometer (BIODEX) and a portable and lightweight device (DINABANG). Methods: From 19 volunteers (age: 28.7±7 y; body mass: 72±10 kg and height: 173±7 cm) we obtained 114 paired MVIC measures and, from the force-time curves of these repetitions, 22507 paired VIC measures of knee extensors. Results: We observed “excellent” repeatability for MVIC (ICC:1.00; p&lt;0.001) between BIODEX (247±79.5 Nm) and DINABANG (247±74.8 Nm), with “trivial” effect (mean difference: 0.12 Nm (0.02%); 95%CI: -0.13 to 0.23 Nm; p=0.606; d=0.048). Bland-Altman plots revealed high accuracy for MVIC (bias: 0.12 Nm) and consistent distribution (precision) inside the limits of agreement (-4.81 to 5.06 Nm) and respective 95%CI. “Excellent” repeatability was also observed for VIC (ICC:1.00; p&lt;0.001) between BIODEX (219±84.1 Nm) and DINABANG (218±84.0 Nm), with “trivial” effect (0.24 Nm (0.11%); 0.08 to 0.11 Nm; p&lt;0.001; d=0.100). Bland-Altman plots revealed high accuracy for VIC (bias: 0.24 Nm) and consistent distribution (precision) inside the limits of agreement (-4.5 to 4.9 Nm) and respective 95%CI. Conclusion: DINABANG is accurate, precise and reliable for torque measurement.

Recent advances in satellite technology have brought enormous potential to ecosystem mapping, which is one of the fundamental components of environmental studies. In this paper, a Random Forest classifier is applied for the strict assessment of the efficiency of ecosystem mapping through a detailed comparative analysis between combined Sentinel-1 and Sentinel-2 data and stand-alone Sentinel-2 imagery over three priority ecosystems, including wetlands, riverine areas, and mangroves in Bangladesh. The collocated images, based on the integration of Sentinel-1 data with Sentinel-2 data, would do better than Sentinel-2 imagery alone over various ecosystems. Particularly, in this study, attention focused on the Hakaluki Haor area for the wetlands, the Padma-Jamuna River confluence for the riverine ecosystem, and the Sundarban forest for mangroves. By leveraging Synthetic Aperture Radar (SAR) data in C-band dual-polarization from Sentinel-1 and four spectral bands (blue, green, red, and near-infrared) from Sentinel-2, the study analyzes imagery from December 2022 to February 2023. A 5% cloud masking filter is applied to optical data to enhance accuracy. In this methodology, 70% of the total signature values are used for training the classification model and the remaining 30% for testing. It can be noticed from the results that with the use of fused data, remarkably high accuracy in classification has been improved, such as overall accuracies of 94.17% for mangroves, 87.30% for riverine, and 85.96% for wetland ecosystems. In contrast, the use of singular Sentinel-2 imagery yields lower accuracies of 91.56%, 85.21%, and 82.51% for the respective ecosystems. The integration of radar data is shown to provide critical information, especially in environments with dense vegetation or cloud cover, where optical data alone may be insufficient. The findings of this study underline the limitations of relying on Sentinel-2 imagery to capture complex details of diverse ecosystems and highlight the need to include Sentinel-1 data for a more holistic analysis. This fusion allows improved accuracy to be achieved, which not only brings in more depth of ecological knowledge but also underpins more effective conservation strategies.

Sorghum (Sorghum bicolor L.) ranks fifth as the most crucial cereal crop globally, yet its seed morphology remains relatively unexplored. This study investigated seed morphology in sorghum based on 115 mini core and 130 Senegalese germplasms. Eight seed morphology traits encompassing size, shape, and color parameters were assessed. Statistical analyses explored potential associations between these traits and resistance to three major sorghum diseases: anthracnose, head smut, and downy mildew. Furthermore, genome-wide association studies (GWAS) were conducted using phenotypic data from over 24,000 seeds and over 290,000 publicly available single nucleotide polymorphisms (SNPs) through the Genome Association and Prediction Integrated Tool (GAPIT) R package. Significant SNPs associated with various seed morphology traits were identified and mapped onto the reference sorghum genome to identify novel candidate defense genes.

Aiming at the problem of small size of some spots on apple leaves and the difficulty of accurate detection of spot targets brought by the complex background of the orchard, this paper takes the alternaria leaf spot, rust, brown spot, grey spot and frog eye leaf spot on apple leaves as the research object, and proposes a high-accuracy detection model YOLOv5-Res and lightweight detection model YOLOv5-Res4 are proposed. Firstly, a multiscale feature extraction module ResBlock is designed by combining the Inception multi-branch structure and ResNet residual idea. Secondly, a lightweight feature fusion module C4 is designed to reduce the number of model parameters while improving the detection ability of small targets. Finally, a parameter streamlining strategy based on optimized model architecture is proposed. The experimental results show that the performance of YOLOv5-Res model and YOLOv5-Res4 model is significantly improved, the [email protected] value is improved by 2.8% and 2.2% compared with YOLOv5s model and YOLOv5n model, respectively, and the size of YOLOv5-Res model and YOLOv5-Res4 model is only 10.8MB and 2.4MB, and the number of model parameters is reduced compared with YOLOv5s model and YOLOv5n model. counts are reduced by 22% and 38.3% compared to the YOLOv5s model and YOLOv5n model.

Despite UAV multi-target detection exhibits considerable developmental potential worldwide, it suffers distinct challenges compared with traditional tasks in this field. These challenges include insufficient feature extraction capabilities for small targets, limited capabilities for multi-dimensional feature fusion, as well as constraints on hardware computation parameters. Especially in mission scenarios such as disaster detection, these challenges will be further amplified. Consequently, this paper introduces SSE-YOLO, an innovative YOLO framework algorithm specially designed to address these challenges. To enhance the model's feature extraction capability, we employ the SPDConv module to replace the original Conv in the backbone section, utilizing depth-separable convolution instead of traditional convolution pooling. Concurrently, we eliminate the SPPF module at the bottom and address a new Separate Kernel Attention Pyramid Pooling (SKAPP) module, substantially enhancing the feature fusion capability at the model's core. Moreover, to address the challenge of multi-dimensional feature fusion, we replace the Concat module of the neck and head with E-BiFPN, transmitting feature information from the backbone to the lower network through four CBS blocks, which effectively resolves the issue of lost contextual information in the model. Meanwhile, SSE-YOLO undergoes ablation experiments on the VisDrone2019 dataset to evaluate its effectiveness against alternative methods, and experimental results illustrate the model's exceptional precision in detecting UAV targets. In comparison to models with comparable experimental accuracy, SSE-YOLO requires remarkably fewer parameters. On the VisDrone2019-DET-test-dev dataset, SSE-YOLO enhances mAP by 17.3%, with a 42.5% reduction in the parameter amounts. Therefore, the proposed method effectively tackles the challenge of reconciling low parameters and high accuracy, presenting a novel pathway for deep learning-based UAV multi-target detection.

High Resolution Melting Analysis (HRM) has been pointed as a suitable alternative method to detect and identify Leishmania species. Herein, we aimed to evaluate the sensitivity, specificity, accuracy, and limitations of a HSP70-HRM protocol both as a diagnostic scheme applied in clinical samples and as a species typing tool for laboratory research and reference services. Our data reveal the pronounced species-typing potential of the HSP70-HRM in DNA from cultured parasites. For clinical samples, however, we advise caution due to the parasite load-dependent accuracy. In the light of these findings and considering the importance of parasite load determination for clinical and research purposes we recommend the integration of the presented typing scheme and the previously published Leishmania quantifying approach as combined tools for clinicians, surveillance, and research.

Precision and accuracy estimation is an important index used to reflect the measurement performance and quality of a measurement system. To reveal the significance and connotations of the precision and accuracy estimation index of a close-range photogrammetry system, several common precision and accuracy estimation methods used in close-range photogrammetry are explained from a theoretical perspective, and the mechanism of the internal coincidence precision estimation and the external coincidence accuracy estimation are deduced, respectively. Through detailed experimental design and testing, the validity and reliability of the proposed precision and accuracy estimation methods are verified, which provides strong evidence for the quality control, optimisation, and evaluation of the measurement results from a close-range photogrammetry system. At the same time, it has significance for the further development of precision and accuracy estimation analysis of close-range photogrammetry systems.

This paper proposes a novel model for a PV cell with parameters variance dependency on temperature and irradiance included. The model relies on commercial available data, calculates the cell parameters for standard conditions and then extrapolates them for the whole operating range. An up-to-date review of the PV modeling is also included with series and parallel parasitic resistance values and dependencies discussed. The parameters variance is analyzed and included in the proposed PV model, where the self-heating phenomenon is also considered. Each parameter variance is compared to the results from different authors. The model includes only standard components and can be run on any SPICE-based simulator. Unlike other approaches that consider the internal temperature as a parameter, our proposal relies on air temperature as an input and computes the actual internal temperature accordingly. Finally, the model is validated via experiments and comparisons to similar approaches are provided.

Monoclonal antibodies (mAbs) have become an increasingly important therapeutic modality in recent years, with applications in oncology, hematology, and immunology. This review discusses the production of therapeutic mAbs, including the various types of mAbs (murine, chimeric, humanized, and fully human), their key applications, and the techniques used for their production, including hybridoma technology, single B cell antibody technology, and phage display technology. The review then proposes advanced techniques to overcome them. These include microfluidic sorting, alternative expression systems (including plants, bacteria, and yeast, and cell-free production systems), and the development of complex antibody formats like bi-specific monoclonal antibodies, antibody fragments, antibody-drug conjugates, and nanobody development. These advanced techniques promise to enhance the efficiency, cost-effectiveness, and scalability of mAb production, paving the way for more effective therapeutic applications. This review highlights the theoretical significance of integrating innovative technologies to overcome existing challenges in mAb production, ultimately advancing the field of precision medicine.

Sustainable agricultural production is endangered by several ecological factors such as drought, extreme temperatures, excessive salts, parasitic ailments, and insect pest infestation. These challenging environmental factors may have adverse effects on future agriculture production in many countries. In modern agriculture, conventional crop breeding techniques alone are inadequate for achieving the increasing population’s food demand on a sustainable basis. The advancement of molecular genetics and related technologies are promising tools for the selection of new crop species. Gene pyramiding through marker assisted selection (MAS) and other techniques have accelerated the development of durable resistant/tolerant lines with high accuracy in the shortest possible period of time for agricultural sustainability. Gene stacking has not been fully utilized for biotic stress resistance development and quality improvement in most of the major cultivated crops. This review emphasizes on gene pyramiding techniques that are being successfully deployed in modern agriculture for improving crop tolerance to abiotic and biotic stresses for sustainable crop improvement.

Low-cost personal exposure monitors (PEMs) to measure personal exposure to air pollution are potentially promising tools for health research. However, their adoption requires robust validation. This study evaluated the performance of twenty-one Plume Lab Flow2 (PLF) by comparing its air pollutant measurements, particulate matter with a diameter of 2.5 μm or less (PM2.5), 10 μm or less (PM10), and nitrogen dioxide (NO2), against several high-quality air pollution monitors under field conditions (at indoor, outdoor, and roadside locations). Correlation and regression analysis were used to evaluate measurements obtained by different PLFs against reference instrumentation. For all measured pollutants, the overall correlation coefficient between the PLFs and the reference instruments was often weak (r<0.4). Moderate correlation was observed for one PLF unit at indoor location and two units at roadside location, when measuring PM2.5, but not for PM10 and NO2 concentration. During periods of particularly higher pollution, 11 PLF tools showed stronger regression results (R2 values > 0.5) with one-hour and 9 PLF units with one-minute time interval. Results show that the PLF cannot be used robustly to determine high and low exposure to poor air. Therefore, the use of PLFs in research studies should be approached with caution if data quality is important to the research outputs.

InSAR and associated analytic methods enable relative surface deformation measurements from low Earth orbit with a potential accuracy of centimeters to millimeters. However, assessing the actual accuracy of individual points can be quite difficult. The analytic methods are complicated enough that na¨ıve analytic error propagation is infeasible, and, in many settings, InSAR practitioners lack sufficient ground truth to assess results. Phase noise due to partial decorrelation from changes in the scattering properties of the ground is a prominent source of accuracy loss. In this paper we present a method to assess the loss of precision due to this component of phase noise. The proposed method consists of generating synthetic data whose statistical properties match that of the actual input SAR data stacks, and then using the synthetic data for an ensemble calculation. The spread of the results of the ensemble calculation indicates the loss of precision. We show examples of the ensemble analysis at a mining operation in South Africa, and demonstrate the ability to assess the most reliable methods for particular points of interest using this ensemble analysis and the ability to filter out points based on the width of the spread of results

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

Nano- and microparticles are increasingly widely used in biomedical research and applications, particularly as specific labels and targeted delivery vehicles. Silica has long been considered the best material for such vehicles, but it has some disadvantages limiting its potential, such as the proneness of silica-based carriers to spontaneous drug release. Calcium carbonate (CaCO3) is an emerging alternative, being easily available, cost-effective, biocompatible material with high porosity and surface reactivity, which makes it an attractive choice for targeted drug delivery. CaCO3 particles are used in this field in the form of either bare CaCO3 microbeads or core/shell microparticles representing polymer-coated CaCO3 cores. In addition, they serve as removable templates for obtaining hollow polymer microcapsules. Each of these types of particles has its specific advantages in terms of biomedical applications. CaCO3 microbeads are primarily used due to their capacity for carrying pharmaceutics, whereas core/shell systems ensure better protection of the drug-loaded core from the environment. Hollow polymer capsules are particularly attractive because they can encapsulate large amounts of pharmaceutical agents and can be so designed as to release their contents in the target site in response to specific stimuli. This review focuses first on the chemistry of the CaCO3 cores, core/shell microbeads, and polymer microcapsules. Then, systems using these structures for the delivery of therapeutic agents, including drugs, proteins, and DNA, are outlined. The results of systematic analysis of available data are presented. They show that the encapsulation of various therapeutic agents in CaCO3-based microbeads or polymer microcapsules is a promising technique of drug delivery, especially in cancer therapy, enhancing drug bioavailability and specific targeting of cancer cells while reducing side effects. To date, research in CaCO3-based microparticles and polymer microcapsules assembled on CaCO3 templates has mainly dealt with their properties in vitro, whereas their in vivo behavior still remains poorly studied. However, an enormous potential of these highly biocompatible carriers for in vivo applications is undoubted. This last issue is addressed in depth in the Conclusion and Outlook sections of the review.

Purpose: When it comes to improving citizen service delivery standard and processes, or broadly, management in government (MIG), many reform programs and improvement efforts are ongoing across different ministries, departments, and agencies. This paper is part of a larger empirical research where we are interested to know what those programs and projects are, and how they are doing, and what the gaps are. Design/methodology/approach: Analyzing the publicly available data on the government portal and donors’ website, this article provides an overall idea of current reforms in various places of government. In parallel, field research was conducted through visiting agency offices, observing office environment and mechanisms, and interviewing public managers who are working at district and sub-district level offices of directorates or agencies.Findings: As a trend, state-led development process and the traditional mode of administration have moved to New Public Management based quality and performance approach. All donors have their own strategy framework document like ‘Country Assistance strategy’, ‘Country Operations and Business Plan’, Logical Framework Document, Focus or Priority Streams, etc. Many of the projects are sectoral and agency or ministry specific and have an inherent limitations, due to ‘cadre’ based organizational structural arrangement. So, it is common ‘not to own the projects’, rather ‘using the fund as much as possible anyway within the given project duration’. When the fund ends, implementing units, either government or NGOs, abandon the projects. That is why many projects are actually half done without significant and sustained direction.Originality/value: We can conclude that the typical ‘top-down’ or ‘trickle down’ conception is still dominant in design and implementation of reforms programs and service quality efforts. So, how to reach systemically at the bottom where public managers provide services to citizens, needs even more deliberation.

Climate change poses a serious threat to global agricultural activity and food production. To address this issue, plant genome editing technologies have been developed to provide an alternative solution for crop improvement. Unlike conventional breeding techniques (e.g., selective breeding and mutation breeding), modern genome editing tools offer more targeted and specific alterations of the plant genome to produce crops with desired traits, such as higher yield and/or stronger resilience to the changing environment. In this review, we discuss the current development and future applications of genome editing technologies in mitigating the impacts of biotic and abiotic stresses on agriculture. We focus specifically on the CRISPR/Cas system, which has been the center of attention in the last few years as a revolutionary genome-editing tool in various species. We also conducted a bibliographic analysis on CRISPR-related papers published from 2012 to 2021 (10 years) to identify trends and possible gaps in the CRISPR/Cas-related plant research. In addition, this review article outlines the current shortcomings and challenges of employing genome editing technologies in agriculture with notes on future prospective. We believe combining conventional and more innovative technologies in agriculture would be the key to optimizing crop improvement beyond the limitations of traditional agricultural practices.

The paper investigates into the intricacies of semiconductor manufacturing, a highly complex process entailing a wide array of subprocesses and diverse equipment. Semiconductors are miniaturized integrated circuits comprising numerous components. The semiconductor manufacturing process begins with the thin disc-shaped silicon wafers. On each wafer, up to thousands of identical chips can be prepared depending upon the diameter of the wafer to build up the circuits layer by layer in a wafer fab. The size of the semiconductors requires a high number of units to be produced, thus necessitating a large amount of data to control for improving the semiconductor manufacturing process. Therefore, the collection and analysis of the equipment data, process data, and machine history data throughout the manufacturing process are required to diagnose faults, monitor the process, and manage the manufacturing process effectively. This research is focused on improving the semiconductor manufacturing process through a rigorous analysis of collected manufacturing process data, employing statistical process control (SPC), data mining techniques, and data-driven decision models. The project's primary objective is to increase the manufacturing process stability and productivity by utilizing the latest data-driven technologies in the scientific community. A structured review was undertaken, exploring contemporary data-driven methodologies in semiconductor manufacturing process improvement, specifically pertaining to process capability, product yield rate, and process stability. This review accentuates a comprehensive evaluation of data-driven methodologies applicable to conventional semiconductor manufacturing facilities, aiming to drive substantial process improvements. It features a detailed demonstration facilitating the selection of optimal semiconductor manufacturing processes to enhance overall operational performance. This study of process improvement in the semiconductor manufacturing steps through the application of data-driven methodologies will be effective in delivering advanced, real-time, and proactive control decisions throughout the manufacturing facilities. This endeavor is expected to promptly provide critical insights for enterprise manufacturing decision-makers to reduce manufacturing cycle time, improve the product yield rate, and increase the overall efficiency of the manufacturing process.

Polyploidy means having more than two basic sets of chromosomes. Polyploid plants may be artificially obtained through chemical, physical and biological (2n gametes) methods. This approach allows an increased gene scope and expression, thus resulting in phenotypic changes such as yield and product quality. Nonetheless, breeding new cultivars through induced polyploidy should overcome deleterious effects that are partly contributed by genome and epigenome instability after polyploidization. Furthermore, shortening the time required from early chromosome set doubling to the final selection of high yielding superior polyploids is a must. Despite these hurdles, plant breeders have successfully obtained polyploid bred-germplasm in broad range of forages after optimizing methods, concentration and time, particularly when using colchicine. These experimental polyploids are a valuable tool for understanding gene expression, which seems to be driven by dosage dependent gene expression, altered gene regulation and epigenetic changes. Isozymes and DNA-based markers facilitated the identification of rare alleles for particular loci when compared with diploids, and also explained their heterozygosity, phenotypic plasticity and adaptability to diverse environments. Experimentally induced polyploid germplasm could enhance fresh herbage yield and quality, e.g. leaf protein content, leaf total soluble solids, water soluble carbohydrates and sucrose content. Offspring of experimentally obtained hybrids should undergo selection for several generations to improve their performance and stability.

Plant breeding conventionally depends on genetic variability available in a species to improve a particular trait in the crop. However, epigenetic diversity may provide an additional tier of variation. The recent advent of epigenome technologies has elucidated the role of epigenetic variation in shaping phenotype. Further, the development of epigenetic recombinant inbred lines (epi-RILs) in the model species such as Arabidopsis has enabled accurate genetic analysis of epigenetic variation. Subsequently, mapping of epigenetic quantitative trait loci (epiQTL) allowed association between epialleles and phenotypic traits. Thus, quantitative epigenetics provides ample opportunities to dissect the role of epigenetic variation in trait regulation, which can be eventually utilized in crop improvement programs. Moreover, locus-specific manipulation of DNA methylation by epigenome-editing tools such as clustered regularly interspaced short palindromic repeats/CRISPR-associated protein 9 (CRISPR/Cas9) can facilitate epigenetic based molecular breeding of important crop plants.

The work at hand focuses on an adaptive system aimed at improving the soundproof performance of car door seals at specific working regimes (cruise), without interfering with the conventional open-closure operations. The idea addresses the necessity of increasing the seal effectiveness, jeopardized by aerodynamic actions more and more important as the speed increase, generating a pressure difference between the internal and the external filed, in the direction of opening the door. To recover this effect, an expanding mechanism was integrated within the seal cavity, driven by an SMA actuator. The material was activated (heated) by Joule effect; its compactness, intrinsic of smart materials, contributed to arrive to a final system characterized by a high level of integrability (expanding cells). In this paper, the development process is described together with the verification activity, aimed at proving the functionality of the realized device. Starting from the industrial requirements, the most appropriate solution was identified highlighting the working principle and the main design parameters involved. Then, the envisaged system was designed and its executive digital mock up (CAD) was released. Prototyping and laboratory validation showed the reliability of the numerical models and the associated predictions. On this basis, the integration task within the actual reference car was faced. To demonstrate the isolation effect of the proposed system, an experimental campaign was finally organized in an anechoic room, achieving significant results on the concept value.

Power quality is a major concern in electrical power systems. The power quality disturbances such as sags, swells, harmonic distortion and other interruptions have impact on the electrical devices and machines and in severe cases can cause serious damages. Therefore it is required to recognize and compensate all types of disturbances at an earliest to ensure normal and efficient operation of the power system. To solve these problems, many types of power devices are used. At the present time, one of those devices, Dynamic Voltage Restorer (DVR) is the most efficient and effective device used in power distribution system. In this paper, design and modeling of a new structure of multifunctional DVR for voltage correction is presented. The performance of the device under different conditions such as voltage swell, voltage sag due to symmetrical and unsymmetrical short circuit, starting of motors, and voltage distortion are described. Simulation result shows the superior capability of proposed DVR to improve power quality under different operating conditions. The proposed new DVR controller is able to detect the voltage disturbances and control the converter to inject appropriate voltages independently for each phase and compensate to load voltage through three single- phase transformers.

Passive marine listening, involving the acoustic monitoring of underwater environments, has become increasingly vital for scientific research, environmental monitoring, and defense applications. However, the success of such applications critically depends on the ability to extract meaningful information from the often noisy and dynamic underwater acoustic environment. In this context, Mel-frequency cepstral coefficients (MFCCs) have emerged as an essential tool for feature extraction, capturing the spectral characteristics of marine sounds and making them ideal for species identification and sound event detection. This research presents an innovative approach to enhance the robustness of MFCC-based passive marine listening through adaptive noise reduction techniques. The proposed approach utilizes dynamic spectral subtraction to counter underwater noise, resulting in enhanced signal-to-noise ratios for desired sounds. This adaptive system adjusts to dynamic underwater noise, allowing it to concentrate on target sounds and suppress interference effectively. The experimentation further validates the effectiveness of the proposed approach, with results reaching 99% on the full dataset of 570 mammals and vessels, demonstrating the effectiveness of SVM and Random Forests in the classification of underwater audio.

The automated transcription of handwritten characters into a legible output is a multi-faceted process with diverse applications. In this paper, a novel approach to optical character recognition (OCR) for handwritten digits is proposed that, in certain components, exceeds current architectures in terms of accuracy, effectiveness, adjustability, temporal efficiency, and/or computational simplicity. This model succeeds in the adoption and enhancement of deprecated or obsolete algorithms across eight steps of image pre-processing—normalization, grayscaling, thresholding/binarization, noise removal, skew-correction, skeletonization/thinning, line separation, and character segmentation. The aforementioned model is evaluated with the use of a Convolutional Neural Network (CNN) leveraging the Balanced eMNIST dataset for training and testing. By suggesting contour-based feature extraction methods as alternatives to pixel-by-pixel iteration, the proposed paradigm demonstrates its capacity to serve as a suitable alternative to current, commonly used algorithms and computational techniques for textual image classification.

Introduction: Determination of radiological bone age (BA) is a diagnostic method that consists of estimating chronological age (CA) from the bone maturation of children. Although environmental and hormonal factors can interfere with bone ossification, the process is essentially dependent on ancestral inheritance. These ethnic backgrounds are not usually considered, which can lead to biased interpretations and inadequate decision-making by pediatricians or forensic experts. The objective of this study was to determine the precision and accuracy of these radiological procedures among different ethnic groups. Methods: A qualitative systematic review carried out following MOOSE statement and previously registered in the International Prospective Registry of Systematic Reviews PROSPERO (CRD42023449512). Search was performed in MEDLINE (PubMed) (n=561), Cochrane Library (n=261), CINAHL (n=103), Web of Science (WOS) (n=181) and public institutional repositories (n=37) from inception to 31st December 2022 using Mesh as “Diagnostic Techniques and Procedures”, “Diagnostic imaging”, “Radiography”, “Age Determination by Skeleton” and free terms combining with booleans “AND” and “OR”. PEDro scale, and Risk of Bias in non-randomized Studies of Exposure (ROBINS-E) were used to assess methodological quality and risk of bias of included studies respectively. Results: 51 articles (n=19,531) were included according to the inclusion criteria previously established. There was a good to moderate methodological quality and a high to very high risk of bias. Skeletal methods for determining BA were precised in terms of intra-observer and inter-observer reliability in all ethnic groups. Regarding to accuracy of Skeletal methods in Caucasians and Hispanic children, GPA was accurate at all ages, but in youths, TW3 RUS could be a consistent alternative. In Asian and Arab, GPA and TW3 overestimated BA in adolescents near adulthood. In African youths, GPA overestimated BA while TW3 was more accurate in estimating CA. Dental and Cervical radiographic methods are equally precise but lesser accurate than Skeletal BA determination. Conclusion: Skeletal radiographic methods GPA and TW3 are both precise for BA determination among all ethnical groups, but their accuracy in estimating CA can be altered by racial bias.

In this paper, we introduce a computational procedure that enables autonomous LEO laser trackers endowed with INSs to increase the current accuracy when shooting at middle distant medium-size LEO debris targets. The code is designed for the trackers to throw the targets into the Atmosphere by means of ablations. In case that the targets are eclipsed to the trackers by the Earth, the motions of the trackers and targets are modeled by equations that contain post-Newtonian terms accounting for the curvature of space. Otherwise, when the approaching targets become visible for the trackers, we additionally use more accurate equations, which allow to account for the local bending of the laser beams aimed at the targets. We observe that under certain circumstances the correct shooting configurations that allow to safely and efficiently shoot down the targets, differ from the current estimations by distances that may be larger than the size of many targets. In short, this procedure enables to estimate the optimal shooting instants for any middle distant medium-size LEO debris target.

Long-term, high-accuracy mapping of built-up land dynamics is essential for understanding urbanization and its consequences for the environment. Despite advances in remote sensing and classification algorithms, built-up land mapping using early satellite imagery (e.g., from the 2000s and earlier) remains prone to uncertainty. We mapped the extent of built-up land in the North China Plain, one of China’s most important agricultural regions, from 1990 to 2019 at three-year intervals. Using dense time-stack Landsat data, we applied discrete Fourier transformation to create temporal predictors and reduce mapping uncertainties for early years. We improved overall accuracy by 8% compared to using spectral and indices predictors alone. We implemented a temporal correction algorithm to remove inconsistent pixel classifications, further improving accuracy to a consistently high level (>94%) across years. A cross-product comparison showed that our study achieved the highest levels of accuracy across years. Total built-up land in the North China Plain increased from 37,941 km² in 1990–1992 to 131,578 km² in 2017–2019. Consistent, high-accuracy built-up land mapping provides a reliable basis for policy planning in one of the most rapidly urbanizing regions of the planet.

With the development of information technology and the popularization of mobile devices, collecting various types of customer data such as purchase history or behavior patterns became possible. As the customer data being accumulated, there is a growing demand for personalized recommendation services that provide customized services to customers. Currently, global e-commerce companies offer personalized recommendation services to gain a sustainable competitive advantage. However, previous research on recommendation systems has consistently raised the issue that the accuracy of recommendation algorithms does not necessarily lead to the satisfaction of recommended service users. It also claims that customers are highly satisfied when the recommendation system recommends diverse items to them. In this study, we want to identify the factors that determine customer satisfaction when using the recommendation system which provides personalized services. To this end, we developed a recommendation system based on Deep Neural Networks (DNN) and measured the accuracy of recommendation service, the diversity of recommended items and customer satisfaction with the recommendation service. The experimental results of is the study showed that both recommendation system accuracy and diversity would have a positive effect on customer satisfaction. These results can further improve customer satisfaction with the recommendation system and promote the sustainable development of e-commerce.

It is important to reduce the computation complexity while maintaining the accuracy of convolution neural networks. We deem it is possible to further reduce the network complexity while ensuring the accuracy. In this paper, we propose a novel feature extraction network called DSRNet which is lightweight but effective. DSRNet follows the basic ideas of stacking modules and short connection, introduces Depthwise Separable convolution and utilizes the Dilated convolution. The proposed network has fewer parameters and achieves outstanding speed. We conducted comprehensive experiments on CIFAR10, CIFAR100 and STL10 datasets, and the results showed the DSRNet has great performance improvement in terms of accuracy and speed.

Commercial sleep devices and mobile-phone applications for scoring sleep are gaining ground. In order to provide reliable information about the quantity and/or quality of sleep, their performance needs to be assessed against the current gold-standard, i.e. polysomnography (PSG; measuring brain, eye and muscle activity). We here assessed some commercially available sleep trackers, namely; a commercial activity tracker: Mi band (Xiaomi, BJ, CHN), a scientific actigraph: Motionwatch 8 (CamNTech, CB, UK), and a much used sleep application: Sleep Cycle (Northcube, GOT, SE). We recorded 27 nights in healthy sleepers using PSG and these devices. Surprisingly, all devices had very poor agreement with the gold standard. Sleep parameter comparisons revealed that specifically the Mi band and the sleep cycle application had difficulties in detecting wake periods which negatively affected the total sleep time and sleep efficiency estimations. However, all 3 devices were good in detecting the most basic parameter, the actual time in bed. In summary, our results suggest that, to-date; available sleep trackers do not provide meaningful sleep analysis but may be interesting for simply tracking times in bed. A much closer interaction with the scientific field seems necessary if reliable information shall be derived from such devices in the future.

Declining agricultural productivity caused by soil salinization are becoming global dilemmas in recent years. Biofertilizers show great potential as a sustainable and environmentally friendly fertilization strategy for soil improvement, but their effectiveness for saline soil amendment and improving plant growth under saline stress is not well understood. Assess the effectiveness of biofertilizers in improving saline soils and enhancing crop growth under saline stress, as well as investigate its related potential mechanisms. Changes in soil physico-chemical properties, plant physiological parameters and soil microbial communities were analyzed through pot experiments. The results showed that the application of biofertilizer reduced total soluble salts (TSS) in soil by 30.8% and increased the Brassica rapa L. biomass by 8.4 times. Biofertilizer application increased soil organic matter (SOM), total nitrogen (TN) and available phosphorus (AP). Biofertilizer applications also increased the SOD, CAT, chl.a, chl.b, total soluble sugars, and Proline content. Biofertilizers present plant growth promotion and potential pathogenic fungi reduction by increasing the abundance of Bacillus and Planococcus and decreasing the abundance of Mortierella and Aspergillus. Overall, the results of this study demonstrated the excellent efficacy of biofertilizers in improving saline soils, and the application of biofertilizer strategies will greatly promote agricultural production.