The unique porous crystal structure of zeolite offers various important utilizations, it is one of the considerations in selecting zeolite at this study as component of composite for restraining noise. It so happens, previous experiments show that banana stem has porous structure, fibrous, high flexibility and can be applied as material for many various products including as component of acoustic material. The combination of both is alleged that it has capability in absorbing noise. This paper presents an investigation on the composite that it was synthesized of Activated Zeolite and Banana Stem Fibre in various weight for determining its sound absorption coefficient alpha (a). Activating natural zeolite was conducted by using 6M HCl in order for enlarging zeolite pores. The sound absorption coefficient was measured in the frequency range between 125 Hz up to 6000 Hz. The results show that the different weight of banana stem fibre as component of the synthesized composite affects the value of alpha and shifts the frequency area.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

Today, enhancing food preservation and safety in the spirit of the bioeconomy suggests the use of biodegradable polymers such as poly-L-lactic acid (PLA) in food packaging and the replacement of chemical additives with natural antioxidant/antibacterial agents such as essential oils and their derivatives. Herein a novel carvacrol (CV) @ natural zeolite (NZ) nanohybrid was developed by employing a new vacuum adsorption desorption method which results in the adsorption of a high CV amount on NZ equal to 61.7 %wt. This CV@NZ nanohybrid was successfully dispersed in a PLA/triethyl citrate (TEC) matrix via a melt-extrusion process to obtain PLA/TEC/xCV@NZ nanocomposite films with 5, 10 and 15 CV@NZ %wt. content. PLA/TEC/xNZ films were also de-veloped for comparison. The overall study resulted in a biodegradable active film with the fol-lowing properties: 10%wt. CV@NZ content (PLA/TEC/10CV@NZ), self-healable properties, 22% higher tensile strength and 40% higher elongation at break, 45% higher water barrier and 40% higher oxygen barrier than pure PLA/TEC matrix. This film also provides high CV release content, high CV control release rate as well as significant antioxidant activity and antibacterial activity against the food pathogens Staphylococcus aureus and Salmonella enterica spp. enterica serovar Typhimurium. This film not only succeeds in extending the shelf-life of fresh pork minced, as shown by total variable count measurements in four days, but also prevents lipid oxidation of fresh minced pork and maintains the minced meat in higher nutritional conditions, as revealed by the heme iron content determination, and in a much better and acceptable sensory condition than the commercial packaging paper.

Ammonium ion is a chemical species that is found in abundance in natural waters, whether underground or surface, but also in wastewater resulting from agricultural and industrial activities. Even if the removal of the ammonium ion from water has been studied for a very long time, it has been found that its removal is far from being solved. In this study, we evaluated the performance of the ammonium ions adsorption process on two adsorbents, zeolite clinoptilolite, ZR, (manufacturer Zeolite Develop-ment SRL, Rupea, Brasov, Romania) and the other granular activated carbon type Norit GAC 830 W. In the first step the paper presents the mineralogical (XRD) and structural (SEM and EDX) characterization of the ZR and determination of the pH zero-point charge, pHZPC, for all the adsorbents. Studies were carried out in equilibrium and kinetic conditions. The efficiency of the adsorbent was investigated in different experimental conditions by varying the initial concentration, particle size, temperature, pH, ionic strength and contact time. The mathematical models and parameters specific to the adsorption isotherms that best describe the experimental results were identified. Langmuir, Freundlich, Temkin and Dubinin-Radushkevich mathematical models were used for comparison. The Langmuir isotherm proved to be the most appropriate to describe the adsorption of ammonium ions on all types of adsorbents used. The adsorption capacity of ammonium ion from synthetic solutions, at 20 °C, pH = 6.09, for the range of initial concentrations 0 - 50 mg/L for Rupea Zeolite is in the range of 10.46 mg/g -12.34 mg/g and for granular activated carbon GAC W830 is 16.64 mg/g. It was found that the increase in temperature and pH have a positive effect on the adsorption capacity of the ammonium ion on the studied adsorbents, and the ionic strength determines the decrease in the adsorption capacity. Kinetic models were also identified that best describe the experimental processes. In this sense, pseudo first order, pseudo second order, intraparticle diffusion and the Elovich model were used. The results of the investigation showed that second-order kinetics governs the adsorption process on ZR zeolites and pseudo-first order for activated carbon.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

The use of zeolite in agriculture as a soil conditioner is becoming an important field of research in crop growth. To study the effect of synthetic zeolite and deficit irrigation on sweet pepper (Capsicum annuum L.) cultivation, an experiment in a controlled environment was conducted. In particular, sweet pepper was cultivated in a glasshouse using polypropylene pots filled with sandy-loam soil to which 2% of zeolite was added. The zeolite employed in the experiments was obtained using coal fly ash as raw material. The experiment was planned in order to have two main treatments consisting of a) soil with zeolite at 2% (Z) and b) soil without zeolite, as control (C), and three subplot treatments consisting of 1) full irrigation at 100% of available water content (AWC) (100); 2) deficit irrigation at 70% of AWC (70); 3) deficit irrigation at 50% of AWC (50). Sweet pepper cultivation started on the 24th April 2023 and lasted until the 23th June 2023 and during the trial environmental data, such as soil humidity, air temperature and relative humidity, and some crop parameters, such as plant height, leaf number, SPAD index, were monitored. At the end of the trial, fresh and dry plant weight, dry matter content, and leaf water potential were measured. Results showed that for plant fresh weight and dry matter content, no significant differences were observed by treatments and their interactions whereas for the other parameters the statistical analysis returned significant differences. The study suggests that the soil structural benefits, resulting from the zeolite application, are not followed by an equal positive effect in terms of sweet pepper growth under deficit irrigation conditions.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

Nanocomposites of TiO₂ Degussa P25 nanoparticles/activated carbon (TiO₂/AC ) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process. The effects of TiO₂/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO₂ and bare AC. TiO₂ nanoparticles exhibited dominant anatase and minor rutile phases, and a crystallite size of approximately 21 nm; while AC had XRD peaks of graphite and carbon, and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO₂ nanoparticles on micron-/submicron AC particles, and uniform TiO₂/AC composites were obtained as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO₂ (e.g., E_1g⁽¹⁾, B_1g⁽¹⁾, E_g⁽³⁾) and carbon materials with D and G bands. The TiO₂/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO₂ or AC. Among the investigated materials, TiO₂/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2×10^-3 min^-1 and an MB removal efficiency of 96.6% after 30 min treatment under UV-Vis irradiation (120 mW/cm²). The enhanced photocatalytic activity for TiO₂/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO₂. Furthermore, TiO₂/AC promotes the separation of photoexcited electron/hole (e^-/h⁺) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO₂/AC composite in this study can be used for treating industrial or household wastewater with organic pollutants.

Raru’s plants bark has long been used as traditional medicine in Batak’s tribe. Raru’s bark is derived from several trees that are usually used in a mixture in Batak traditional beverages. This bark is generally used as antidiabetic remedies. This study aims to combine the rarus’s bark extract and mocaf activated-carbon (MAC) in order to study antidiabetics in rats. The combination of raru’s bark extract and MAC were tested on male rats as of Sprague Dawley strain for testing antidiabetic bioactivity. The result showed that antidiabetic activity of raru’s extract and MAC exposed the antidiabetic level declines in rat’s blood. The various treatments of different concentration ratios of raru’s extract and MAC useful in the experiments showed that the levels of blood level reduction were slightly different (14-21%). The raru’s extract pure was observed more effective in decreasing the blood glucose level in rat’s blood, in comparison the positive control. The mixture of raru’s extract and MAC with 75:25 ratio is better than 50:50 ratio. The involvement of MAC in the alleged antidiabetic agent did little in improving the blood glucose level decrease in rat’s blood. Raru’s extract and MAC indicate its potential utilization as an antidiabetic agent.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

: The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDX, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.78; 2.24 and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDS, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a breakthrough adsorption experimental setup at room temperature. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.47; and 1.20 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

Non-Vitamin K Oral Anticoagulants (NOACs) have revolutionized anticoagulant therapy, offering improved safety and efficacy over traditional agents like warfarin. This review comprehensively examines the dual roles of NOACs—Apixaban, Rivaroxaban, Edoxaban, and Dabigatran—not only as anticoagulants but also as modulators of inflammation via Protease-Activated Receptor (PAR) signaling. We highlight the unique pharmacotherapeutic properties of each NOAC, supported by key clinical trials demonstrating their effectiveness in preventing thromboembolic events. Beyond their established anticoagulant roles, emerging research suggests that NOACs influence inflammation through PAR signaling pathways, implicating factors such as FXa and Thrombin in the modulation of inflammatory responses. This review synthesizes current evidence on the anti-inflammatory potential of NOACs, exploring their impact on inflammatory markers and conditions like atherosclerosis and diabetes. By delineating the mechanisms by which NOACs mediate anti-inflammatory effects, this work aims to expand their therapeutic utility, offering new perspectives for managing inflammatory diseases. Our findings underscore the broader clinical implications of NOACs, advocating for their consideration in therapeutic strategies aimed at addressing inflammation-related pathologies. This comprehensive synthesis not only enhances understanding of NOACs' multifaceted roles but also paves the way for future research and clinical applications in inflammation and cardiovascular health

Series of bifunctional catalysts, MoS2/Al2O3(70 wt.%)-zeolite (30 wt.%) (zeolite – ZSM-5, ZSM-12, ZSM-22 and silica aluminophosphate SAPO-11), were synthesized for hydroconversion of methyl palmitate (10 wt.% in dodecane) in a trickle-bed reactor. Mo loading was about 7 wt.%. Catalyst and supports were characterized by different physical-chemical methods (HRTEM-EDX, SEM-EDX, XRD, N2 physisorption, FTIR spectroscopy). Hydroprocessing was performed at temperature of 250-350°C, hydrogen pressure 3.0-5.0 MPa, liquid hourly space velocity (LHSV) 36 h-1, H2/feed ratio – 600 Nm3/m3. Complete conversion of oxygen-containing compounds was achieved at temperature 310°C in the presence of MoS2/Al2O3-zeolite catalysts, the selectivity for the conversion of methyl palmitate via the ‘direct’ hydrodeoxygenation (HDO) route was over 85%. The yield of iso-alkanes gradually increases in order: MoS2/Al2O3 < MoS2/Al2O3-ZSM-12 < MoS2/Al2O3-ZSM-5 < MoS2/Al2O3-SAPO-11 < MoS2/Al2O3-ZSM-22. The sample MoS2/Al2O3-ZSM-22 demonstrated the highest yield of iso-alkanes (40%). Hydroisomerization activity of the catalysts was in a good correlation with concentration of Brønsted acid sites of synthesized supports.

Coral reef is an important underwater ecosystem that is rich in biodiversity in it. Coral growth has decreased drastically due to physical and chemical threats, such as the effect of warming seawater, fish bombing activities, and the effects of wastewater. The efficiency level of coral transplantation is determined by many factors, including the stability of the environment's physical condition, the level of coral diversity, and the method of transplantation. The influence of the planting medium can also be a key factor in succeeding the coral transplantation process. The use of stable and natural growing media can be a solution to replace conventional growing media that have been used. Zeolite material is a medium that has many advantages such as amending the trace elemental contents of saltwater such as carbon absorbents, detoxifiers, ammonia remover, catalysts, promoting marine micro-algal growth, become a media for bacterial growth, etc. This review discusses the possibility of zeolites as the candidate media that can be used as a new medium in coral transplantation process to accelerate coral growth and maintain coral health by increasing the adaptation of corals to the effects of global climate change.

In the upgrading of biomass pyrolysis vapors to hydrocarbons, dehydration accomplishes a primary objective of removing oxygen and acidic zeolites represent promising catalysts for dehydration reaction. Here, we utilize density functional theory calculations to estimate adsorption energetics and intrinsic kinetics of alcohol dehydration over H-ZSM-5, H-BEA, and H-AEL zeolites. ONIOM calculations of adsorption energies were observed to be inconsistent when benchmarked against QM/Hartree-Fock and periodic boundary condition calculations. However, reaction coordinate calculations of adsorbed species and transition states were consistent across all levels considered. Comparison of ethanol, iso-propanol (IPA), and tert-amyl alcohol (TAA) over these three zeolites allowed for a detailed examination of how confinement impacts reaction mechanisms and kinetics. TAA, seen to proceed via a carbocationic mechanism, was found to have the lowest activation barrier, followed by IPA and then ethanol, both of which dehydrate via a concerted mechanism. Barriers in H-BEA were consistently found to be lower than in H-ZSM-5 and H-AEL, attributed to late transition states and either elevated strain or inaccurately estimating long-range electrostatic interactions in H-AEL, respectively. Molecular dynamics simulations revealed that the diffusivity of these three alcohols in H-ZSM-5 are significantly overestimated by Knudsen diffusion, which will complicate experimental efforts to develop a kinetic model for catalytic fast pyrolysis.

Binderless zeolite macrostructures in the form of ZK-4 microspheres were prepared using anion exchange resin beads as shape directing macrotemplates. The particles were synthesized under hydrothermal conditions at different temperatures and treatment times. The influence of the different synthesis parameters was investigated by X-ray diffraction, scanning electron microscopy, fluorescence X, nitrogen adsorption measurements and ²⁹Si solid NMR. Fully crystalline spheres similar in size and shape to the original resin beads were obtained by a hydrothermal treatment at the highest temperatures (150 - 180 °C) for a short treatment time of 24 h. The synthesized microspheres showed to be promising in the molecular decontamination of Volatile Organic Compounds (VOCs).

The optimal combination of five components to develop a concrete for high-temperature applications was studied through a response surface methodology known as mixture design of experiment. The selected components were water, an alkali-activated binder based on ferronickel slag activated with potassium silicate and potassium hydroxide, and three aggregate sizes corresponding to 0-4 mm, 4-8 mm, and 8-16 mm. Selected response parameters were slump and compressive strength before and after heat exposure. Six cubes of side 150 mm were cast for each concrete mix, three for ambient and three for residual (post-heat exposure) compressive strength. All 20 concrete mixes were exposed to a thermal load of 600 °C for two hours. The optimal concrete mix was adapted for large-scale applications, by increasing slump and replacing limestone with olivine aggregates for enhanced residual compressive strength. The adapted mix resulted in concrete with 76 MPa and 32 MPa compressive strength before and after high-temperature exposure. The CO2 emissions were found to be 77 % lower when compared to traditional OPC concrete.

This study primarily investigates the effect of fly ash (FA) content on the mechanical properties and hydration performance of alkali-activated ground granulated blast furnace slag cements (AAGC), and compares the related properties with ordinary Portland cement (OPC). Additionally, the study examined the hydration products, thermal analysis, MIP, SEM, chemically bound water, and pH values of AAGC. The compressive strength of AAGC showed a retrogression phenomenon from 3 to 28 days, with the 14-day and 28-day compressive strengths of AAGC being higher than those of OPC. The AAGC with 20% FA content exhibits the highest 28-day compressive strength (75 MPa). The hydration heat release rate curved of OPC and AAGC can be divided into the initial induction period, induction period, acceleration period, deceleration period and steady period. As FA content increases, the 28-day pore volume of AAGC increased while pH values and chemically bound water decrease. SEM images of AAGC with low FA content showed more microcracks.

This study explores cutting-edge and sustainable green methodologies and technologies for the synthesis of functional nanomaterials, with a specific focus on the removal of water contami-nants and the application of kinetic adsorption models. Our research adopts a conscientious ap-proach to environmental stewardship by synergistically employing eco-friendly silver nanopar-ticles, synthesized using Justicia Spicigera extract as a biogenic reducing agent, in conjunction with Mexican zeolite to enhance contaminant remediation, particularly targeting Cu²⁺ ions. Structural analysis, utilizing X-ray diffraction (XRD) and high-resolution scanning and transmis-sion electron microscopy (TEM and SEM), yields crucial insights into nanocomposite structure and morphology. Rigorous linear and non-linear kinetic models, encompassing pseudo-first order, pseudo-second order, Freundlich, and Langmuir, are employed to elucidate the kinetics and equilibrium behaviors of adsorption. Results underscore the remarkable efficiency of the Zeolite-Ag composite in Cu²⁺ ion removal, surpassing traditional materials, achieving an im-pressive adsorption rate of 98% for Cu. Furthermore, the Zeolite-Ag composite exhibits maxi-mum adsorption times of 480 minutes. In the computational analysis, an initial mechanism for Cu²⁺ adsorption on zeolites is identified. The process involves rapid adsorption onto the surface of the Zeolite-Ag NP composite, followed by a gradual diffusion of ions into the cavities within the zeolite structure. Upon reaching equilibrium, a substantial reduction in copper ion concen-tration in the solution signifies successful removal. This research represents a noteworthy stride in sustainable contaminant removal, aligning with eco-friendly practices and supporting the potential integration of this technology into environmental applications. Consequently, it pre-sents a promising solution for eco-conscious contaminant remediation, emphasizing the utiliza-tion of green methodologies and sustainable technologies in the development of functional na-nomaterials

Synthesis of zeolite T with a variety of desired characteristics necessitate extensive work in the formulation and practical experiments either by conventional hydrothermal methods or aided with different approaches and synthesis techniques such as secondary growth or microwave irradiation. The objectives of this review are to adduce the potential work in zeolite T (Offretite-Erionite) synthesis evaluating determining factors affecting the synthesis and quality of the zeolite T crystals. Attention is given to the extensive studies that interconnect with other significant findings.

A sustainable green one pot procedure for the synthesis of dihydropyrimidinones (DHPMs) derivatives by a three-component reaction of β-ketoester derivatives, aldehyde and urea or thiourea over the alkali-treated H-ZSM-5 zeolite under ball-milling has been developed. The product was isolated by simple washing of the crude reaction residue with ethyl acetate followed by evaporation of solvent. The hierachical zeolite catalyst (MFI27_6) showed high yield (86–96%) of dihydropyrimidinones (DHPMs), in very short time (10-30 min). The catalyst is recycled for subsequent reactions in four runs without appreciable loss of activity and high yields of products provide efficient protocol for Biginelli reactions.

Portland cement emits large amounts of CO2 in production. Given proposals for "carbon peaking and carbon neutralization" studying alternative low-carbon cementitious materials to reduce emissions is extremely important. Alkali-activated slag (AAS) cement, a new green cementitious material, has high application potential. The chemical corrosion resistance of AAS concrete is important for ensuring durability and prolonging service life. Studying the chemical corrosion mechanism of AAS concrete and understanding its influence on performance provides important theoretical foundations for application in different environments.

In this study, high-performance FAU (NaY type) zeolite membranes were successfully synthesized using small-sized seeds of 50 nm, and their gas separation performance was systematically evaluated. Employing nano-sized NaY seeds and an ultra-dilute reaction solution with a molar composition of 80 Na2O: 1Al2O3: 19 SiO2: 5000H2O, the effects of synthesis temperature, crystallization time, and porous support (α-Al2O3 or mullite) on the formation of FAU membranes were investigated. The results illustrated that further extending the crystallization time or increasing the synthesis temperature led to the formation of a NaP impurity phase on the FAU membrane layer. The most promising FAU membrane with a thickness of 2.7 µm was synthesized on an α-Al2O3 support at 368 K for 8 h, and had good reproducibility. The H2 permeance of the membrane was as high as 5.34×10-7 mol/(m2 s Pa), and the H2/C3H8 and H2/i-C4H10 selectivities were 183 and 315, respectively. The C3H6/C3H8 selectivity of the membrane was as high as 46 with a remarkably high C3H6 permeance of 1.35× 10-7 mol/(m2 s Pa). The excellent separation performance of the membrane is mainly attributed to the thin, defect-free membrane layer and relatively wide pore size (0.74 nm).

Zeolite Y with microporous and hierarchical structure containing Ti–Ni and Ti–Co oxides were obtained as active photocatalysts. Different Ti amounts (5, 10% TiO2) were supported, followed by loading of Ni or Co oxides (5 %). The X-ray diffraction evidenced the presence of TiO2 as anatase. N2 adsorption-desorption results showed type IV isotherms, for hierarchical zeolite Y samples, and a combination of type IV and I isotherms, for zeolite Y samples. UV–Vis diffuse reflectance spectra showed shift of absorption band to visible with increasing of Ti loading and especially after Co and Ni addition. A significant effect of the support was evidenced for Ti and interaction with Co/Ni species. The zeolite Y support stabilizes Ti in the 4+ oxidation state while hierarchical zeolite Y support favored the formation of Ti 3+ species and oxidation of Co and especially of Ni to 3+. Photocatalytic activity, under UV and visible light, was evaluated in degradation of amoxicillin, used as a model test. The photocatalytic mechanism was investigated using ethanol, p-benzoquinone and KI as ·OH, ·O2- radicals and hole (h+) scavengers. The best results were obtained for the immobilized Ni-Ti species on hierarchical zeolite Y support.

Traditional photodynamic therapy (PDT) is often limited in its efficacy by insufficient light penetration, inefficient photosensitizer energy transfer, and inadequate target tissue oxygenation. X-ray activated PDT (XPDT), using nanoparticle (NPs) photosensitizers comprised of europium-doped yttrium oxide cores encased within silica shells (Y₂O₃:Eu@SiO₂), offers the potential of overcoming most of these limitations. Aimed at maximizing the generation of reactive oxygen species (ROS), this study reports methodologies for investigation of the effects of synthesis conditions on the characteristics of Y₂O₃:Eu@SiO₂ NP. Transmission electronic microscope (TEM) revealed that the NP core diameter was linearly, positively correlated with condensation time (R2 = 0.7357, p < 0.05) and linearly, negatively correlated with urea concentration (R2 = 0.958, p < 0.05). The addition of cetyltrimethylammonium bromide (CTAB) during core synthesis demonstrated enhanced particle dispersion. Silica coating via APTES-1 and TEOS-3 conditions resulted in Y₂O₃:Eu@SiO₂ NPs that generated the highest ROS, with 8.7-fold and 8.9-fold increase respectively in relative fluorescence intensity at 8 Gy irradiation compared to a 5.2-fold increase in PBS under the same condition. In vivo evaluation using 18F-fluorothymidine positron emission tomography (18F-FLT PET) of mouse xenografts of a human prototypical cancer (ovarian) revealed a 55% reduction in tumor proliferation of radiation-sensitive CAOV3 tumors treated with Y₂O₃:Eu@SiO₂ NPs compared to a 19% reduction in tumor proliferation of radiation-resistant SKOV3 tumors on the fourth day post-treatment. Taken together, these findings suggest Y₂O₃:Eu@SiO₂ NPs can serve as effective photosensitizers for XPDT and their performance characteristics can be optimized by selecting synthesis conditions and parameters to deliver the desirable therapeutic effects, offering novel approaches to circumventing many of the limitations of conventional PDT in the treatment of cancer.

A challenging problem in the aquaculture industry is bacterial disease outbreaks which results in the global reduction of fish supply and foodborne outbreaks. Biofilms in marine pathogens protect against antimicrobial treatment and host immune defence. Zeolites are minerals of volcanic origin made from crystalline aluminosilicates which are useful in agriculture and in environmental management. In this study, silver ion-exchanged zeolite A of four concentrations; 0.25M (AgZ1), 0.50M (AgZ2), 1.00M (AgZ3)and 1.50M (AgZ4) were investigated for biofilm inhibition and antimicrobial properties against two predominant marine pathogens V. campbelli and V. parahemolyticus by employing the Minimum Inhibitory Concentration(MIC), Crystal Violet Biofilm Quantification assays as well as Scanning Electron Microscopy. In the first instance, all zeolite samples AgZ1-AgZ4 showed antimicrobial activity for both pathogens. For V. campbellii AgZ4 exhibited the highest MIC at 125.00 µg/ml while for V. parahaemolyticus the highest MIC was observed for AgZ3 at 62.50 µg/ml. At sublethal concentration, biofilm inhibition of V. campbelli and V. parahemolyticus by AgZ4 were observed at 60.2% and 77.3% inhibition respectively. Scanning electron microscopy exhibited profound structural alteration of the biofilm matrix by AgZ4. This is the first known study that highlights the potential application of ion-exchanged Zeolite A against marine pathogens and their biofilms.

The pyrolysis process has emerged as an attractive option for waste treatment. In this technology, inorganic compounds play catalytic effects in the pyrolytic reaction of organic materials, increa-sing the char's yield, porosity, and physicochemical properties. The present research investigates and compares the slow pyrolysis of spent coffee grounds (SCG) using potassium hydroxide (KOH) (weight ratio of 1:1) and landfill leachate membrane concentrate (LLMC) residue (weight ratio of 1:1) as pyrolitic additives. We hypothesized that the high content of alkali and alkaline earth metals in LLMC could enhance the yield or improve the quality of the carbon-based material produced in pyrolysis. This strategy could be a sustainable alternative for valorizing SCG and landfill wastes, replacing catalyzing agents such as steam, CO2, and chemical additives used on an industrial scale. The char yields in slow pyrolysis ranged from 18 to 24%. The SCG had a low specific surface area (4.5 m2 g-1), contrasting with the notable surface areas observed in both ac-tivated chars. In particular, the KOH-activated char displayed a higher surface area than the LLMC-activated char (1960 vs. 1130 m2 g-1). On the other hand, the combustion enthalpy of the LLMC-activated material was estimated at 22 MJ kg-1. This value was 22% higher than the energy enthalpy of SCG and KOH-activated char used for comparison. Our findings confirm that pyrolysis of SCG with KOH produces a microporous material with a high specific surface area. In contrast, the resulting LLMC-activated char demonstrates a higher calorific value. Our findings could contribute to establishing potential industrial applications for SCG and LLMC residues to produce energy and high-value materials.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

Disulfiram (DSF), an anti-alcoholism medicine, exerts treatment effects in patients suffering from persistent Borreliosis and also exhibits anti-cancer effects by its copper chelating derivatives. Since chronic/persistent borreliosis is characterized by increased amounts of proinflammatory macrophages, this study investigated opsonin-independent phagocytosis, migration and surface marker expression of in vivo activated human monocyte-derived macrophages and dendritic cells with and without DSF treatment. Phagocytosis of non-opsonized Dynabeads® M-450 and migration of macrophages and dendritic cells were monitored using live cell analyzer Juli™ Br for 24h by imaging every 3.5 min. Results were analyzed by a newly developed software based on the differential phase contrast images of cells before and after ingestion of Dynabeads bearing an electron dense iron core. As a control, phagocytosis was also monitored by visual counting of ingested beads. DSF decreased the phagocytic capacities exhibited by global macrophages and dendritic cells. DSF also impaired the migration of human monocyte-derived macrophages and dendritic cells (hMDMD) and significantly reduced the expression densities of surface antigens CD45 and CD14. In cells consisting of anti-inflammatory M2 macrophages, DSF led to a remarkable cell death and also increased oxidative stress as determined by MitoSox staining. Mitochondrial oxidative stress was a prominent feature in M2 macrophages which were more sensitive to DSF-induced cytotoxicity.

The DNA Damage Response (DDR) network and the mitogen-activated protein kinase (MAPK) signaling pathway are crucial mechanisms for the survival of all living beings. An accumulating body of evidence suggests that there is a crosstalk between these two systems, thus favoring the appropriate functioning of multi-cellular organisms. On the other hand, aberrations within these mechanisms are thought to play a vital role in the onset and progression of several diseases, including cancer, as well as in the emergence of drug resistance. Here, we provide an overview of the current knowledge regarding alterations in the DDR machinery and the MAPK signaling pathway, as well as abnormalities in the DDR-MAPK functional crosstalk in multiple myeloma, the second most common hematologic malignancy. We also present the latest advances in the development of anti-myeloma drugs targeting crucial DDR- and MAPK-associated molecular components. These data could potentially be exploited to discover new therapeutic targets and effective biomarkers, as well as for the design of novel clinical trials. Interestingly, they might provide a new approach to increase the efficacy of anti-myeloma therapy by combining drugs targeting the DDR network and the MAPK signaling pathway.

The present study provides molecular insight into the mechanisms underlying energy dissipation and lubrication of a smooth contact lubricated by an ionic liquid. We have performed normal and lateral force measurements with a surface forces apparatus and by colloidal probe atomic force microscopy on following model systems: 1-ethyl-3-methyl imidazolium bis-(trifluoro-methylsulfonyl)imide, in dry state and in equilibrium with ambient (humid) air; the surface was either bare mica or functionalized with a polymer brush. The velocity-dependence of the friction force reveals two different regimes of lubrication, boundary-film lubrication, with distinct characteristics for each model system, and fluid-film lubrication above a transition velocity V*. The underlying mechanisms of energy dissipation are evaluated with molecular models for stress-activated slip and flow, respectively. The stress-activated slip assumes that two boundary layers (composed of ions/water strongly adsorbed to the surface) slide pass each; the bond dynamics and the strength of the interaction at the slip plane dictate the change in friction -decreasing, increasing or remaining constant- with velocity in the boundary-film lubrication regime. Above a transition velocity V*, friction monotonically increases with velocity in the three model systems. Here, layers of ions slide past each (“flow”) under a shear stress and friction depends on a shear-activation volume that is significantly affected by confinement. The proposed friction model provides a molecular perspective of the lubrication of smooth contacts by ionic liquids and allows identifying the physical parameters that control friction.

Alkali-activated materials, sometimes called geopolymers, can be used as alternative cementitious materials to conventional Portland cement. There is a significant current interest in these materials due to their low CO2 footprint. Typical applications of alkali-activated materials are within civil engineering, however, potential applications as well cementing material within oil & gas are also being studied with emerging interest. This paper presents a systematic study of compressive strength development from 1 to 28 days for metakaolin-based alkali-activated cement. The results show that compressive strength is highly dependent upon the initial Si/Al ratio in the mix design, as well as the concentration of the activator solution. Furthermore, due to the relatively low initial reactivity of the used metakaolin material, different types of co-binders were included in the slurry composition to improve early strength development. The two different co-binders tested were another, more reactive metakaolin material and Blast Furnace Slag (GGBFS). It was found that both these co-binders performed as intended, by ensuring early strength development via precipitation of K-A-S-H and C-A-S-H gels, respectively, and also by enabling subsequent strength development due to improved dissolution of the low-reactive metakaolin.

Monometallic (Ni, Co, Cu) and bimetallic (Ni-Co, Ni-Cu) 10-20 wt. % metal containing catalysts supported on fly ash zeolite were prepared by post-synthesis impregnation method. The catalysts were characterized by X-ray powder diffraction, N2 physisorption, XPS and H2-TPR methods. Finely dispersed metal oxides and mixed oxides were detected after the decomposition of impregnating salt on the relevant zeolite support. By reduction intermetallic, NiCo and NiCu phases were identified in the bimetallic catalysts. Hydrogeoxygenation of lignocellulosic biomass-derived levulinic acid to γ-valerolactone (GVL) was studied. Bimetallic, 10 wt. % Ni, 10 wt. % Cu or Co containing fly ash zeolite catalyst showed higher catalytic activity than monometallic ones. Their selectivity to GVL reached 70-85 % at 100 % conversion. The reaction proceeds through formation of 4-hydroxy pentanoic acid, as the only intermediate compound.

Starting from the environmental issues related to global warming, climate change and reduction of greenhouse gas emissions, this review paper describes how CO₂ recycling can represent a challenging strategy suitable to explore new concepts and opportunities for catalytic and industrial development. In this view, the production of dimethyl ether (DME) from catalytic hydrogenation of CO₂ appears as a viable technology, able to meet also the ever-increasing need for alternative environmentally-friendly fuels and energy carriers. Basic considerations on thermodynamic aspects controlling DME production from CO₂ are presented, then summarizing the main catalytic systems developed in such a field. Special attention is paid on the role assumed during last years by zeolite-based systems, either in the methanol-to-DME dehydration step or in the one-pot CO₂-to-DME hydrogenation. On the whole, the productivity of DME results significantly to be dependent on several catalyst features, linked not only to the metal-oxide phase responsible for CO₂ activation/hydrogenation, but also to specific properties of the zeolites (i.e., topology, porosity, surface area, acidity, interaction with active metals, distributions of metal particles, …) influencing activity and stability of hybridized bifunctional heterogeneous catalysts.

Activated carbon (AC) is an effective adsorbent for creatinine removal in hemoperfusion. However, the hemocompatibility and adsorption capacity of AC was required to be improved furthermore. Heparin, a widely used anticoagulant biomacromolecule, could improve the hemocompatibility of the absorbents in different ways based on its molecular weight. Thus, it was necessary to study the surface modification with unfractionated heparin (UFH) or low molecular weight heparin (LMWH) on improvement of hemocompatibility and adsorption. In this study, UFH and LMWH were respectively grafted on AC through polyethyleneimine as an intermediate layer. The modification of AC about morphology, mechanical strength and pore structure was characterized by XPS, SEM, TA and BET. It was found that compared with AC, the morphology and mechanical strength AC-UFH and AC-LMWH could be well maintained, but the BET surface was decreased due to the grafting of macromolecules. Furthermore, AC-UFH and AC-LMWH showed the better hemocompatibility on protein adsorption, APTT and platelet activation compared with AC, in which AC-LMWH had lower fibrinogen adsorption and longer APTT than AC-UFH. Besides, it was found that AC, AC-UFH and AC-LMWH had no significant effect on blood cell composition. Finally, the adsorption capacity of adsorbents for creatinine was evaluated. Although there was no significant difference between AC-UFH and AC-LMWH, it was found that heparin could be interacted with creatinine to enhance the adsorption capacity when compared with AC-PEI. This study deepened the understanding of anticoagulation of heparinized surface and provided a theoretical basis for adsorbents in hemoperfusion.

Some of Iran's gas resources are known as sour gas because one of the major by-products of this gas is water. In fact, natural gas is combined with water vapor in underground reservoirs. In some areas, the amount of water vapor in natural gas is so high that it can be used as a source of drinking water. However, it should be noted that water vapor in natural gas may exacerbate corrosion in pipes and industrial equipment, and the combustion of more natural gas produces high temperatures that can lead to the production of nitrogen oxides (NOx), which They are the cause of air pollution. This is while the processed gas has a standard percentage composition in which the amount of water has the lowest position. The removal of moisture from natural gas is due to the need to prevent the reduction of the calorific value of the gas and also to purify the gas in order to achieve the necessary standards for delivering gas to petrochemicals, industries and domestic uses. The main goal of this research is to investigate the influencing parameters on zeolite TiO2 nanocomposite membranes in order to absorb moisture from gas. For this reason, with the construction of a TiZ-V membrane as a standard membrane, the result of the initial evaluation of a suitable membrane for gas dehumidification was made, and this membrane was placed as a standard for measuring the effect of the manufacturing parameters in a way that in each stage of membrane construction It was found that it was different from standard TiZ-V membrane only in terms of one parameter. This type of investigation made it possible to determine the effect of various effective parameters in membrane construction on efficiency. The findings showed that increasing the concentration of SiO2 has the greatest effect on increasing the water flux of the membrane. According to the other findings of this study, the effect of increasing the reaction time of the vapor phase carrier has been to reduce the process of paternity selectivity loss at higher pressures. Although due to the safety limitation of the equipment to measure the efficiency of the membrane at pressures higher than 7 bar, this measurement was not carried out, but charts were presented regarding the state of the water in the water, which were a measure of the superiority of the water in the water in comparison to the gas in the water, which is the higher water in the water It is an indicator of the appropriateness of the membrane's efficiency at its corresponding pressure, so that the examination of the difference between these two graphs shows the possibility of using the membrane at higher pressures

In this study, fig leaves, zeolite and alginate were used to prepare a biocomposite for the adsorption of Pb(II) ions from aqueous solutions. Effects of various parameters on the biosorption process such as pH, temperature, initial lead concentration and contact time have been investigated. Maximum uptake of Pb(II) ions (85%) has been achieved at pH 6, with 25 mg/L of initial concentration and at a temperature of 288.15 K. Among the applied models, the data correlated well with Freundlich and D-R models and it was established that the biosorption was physical in nature. The amount of adsorbed lead per gram of sorbent was found to be 150.3 mg/g. Thermodynamic parameters showed the exothermic heat of biosorption and the feasibility of the process. Results have suggested that the prepared biosorbent possesses promising biosorption potential.

This study investigates the characteristics of activated carbons derived from biomass plant residues: rice husk (OSL) of the genus Oryza, reed stalks (PhAC) of the genus Phragmites, pine sawdust (PSL) of the genus Pinus, and wheat straw (TAL) of the genus Triticum. Activation was carried out using potassium hydroxide, employing a two-stage pyrolysis under air. The study examined the influence of activation temperature, duration, concentration of the impregnating agent, and impregnation time. Characteristics such as sorbent porosity, bulk density, and hydrocarbon sorption capacity were determined. Adsorption capacity was assessed using BET analysis and the iodine number determination method, with the highest iodine number achieved being 2809 mg/g, indicating high adsorption capability. The structural morphology of the activated carbons was evaluated by SEM, and their chemical surface characteristics were identified by IR spectroscopy. Computational analysis of the nitrogen sorption isotherms using the Barrett-Joyner-Halenda (B-J-H) method and the Dubinin-Radushkevich (D-R) equation showed that activated carbon samples from rice husk and pine sawdust possess a developed specific surface area and contain micro- and mesopores. The Dubinin-Astakhov (D-A) approach was used to study the pore diameter of activated carbon, revealing significant findings on pore structure. The maximum micropore volume was found in activated carbon samples from pine sawdust (PSL), measuring 0.46 cm³/g. All activated carbon samples of plant origin were tested under field conditions for the remediation of oil-contaminated areas near the “Zhanatalap” oil field in the Atyrau region. By the 16th day, the oil-contaminated soil treated with rice husk activated carbon was cleaned by 67.1%.

(1) Background: Hepatoblastoma is the most common primary liver malignancy in children. During its development, metabolic reprogramming becomes particularly relevant due to the liver's intrinsic metabolic functions. Enhanced glycolysis, glutaminolysis, and fatty acid synthesis have been implicated in the proliferation and survival of hepatoblastoma cells. In this study we screened altered over expression of metabolic enzymes in hepatoblastoma tumors at tissue and single cell level. A hepatoblastoma tumor expression metabolic score was established and validated by machine learning; (2) Methods: Starting from Mammalian Metabolic Enzyme Database, bulk RNA-sequencing from GSE104766 dataset was investigated by supervised analyses (tumors versus adjacent liver tissue). Overexpressed enzymes in hepatoblastoma tumors were functionally enriched on KEGG metabolic database to draw a metabolic network with Cytoscape. Activated metabolic markers were used to compute a single-cell metabolic score in human and PDX hepatoblastoma samples from GSE180665 dataset (sc-RNAseq). ROC and area under curve (AUC) were computed on metabolic score. Elasticnet model tuning for metabolic marker expression was performed with r-caret on single cell transcriptome and revealed importance of individual marker to predict tumor cell status; (3) Results: Differential expression analysis on bulk transcriptome identified 287 significantly regulated enzymes between tumor and adjacent liver tissues: 59 of them were found overexpressed in tumors. 45 of the 59 over expressed enzymes were recognized in KEGG database which highlighted a main metabolic network enriched in amino acid metabolism but also carbohydrate, steroid, one carbon, purine, and glucoaminoglycan metabolisms. Based on expression of the 59 over expressed enzymes, the single cell metabolism score computed on GSE180665 dataset allowed to predict tumor cell status with and AUC of 0.98 (sensibility 0.93, specificity: 0.94). Elasticnet model tuned at 0.97 of AUC on individual marker single cell expression ranked top tumor predictive markers by decreasing importance: FKBP10, ATP1A2, NT5DC2, UGT3A2, PYCR1, CKB, GPX7, DNMT3B, GSTP1, and OXCT1; (4) Conclusion: An activated metabolic transcriptional program potentially affecting epigenetic functions was observed by bulk RNAseq in tumors of hepatoblastoma and confirmed at single cell levels in tumor cells.

Alkali-activated materials are alternative building binders, where secondary raw materials are processed. Possibility to use landfilled waste materials in their preparation, increases their potential application in construction practice, and therefore they are subject to extensive research, especially in recent years. This paper briefly summarizes interesting results of an experiment aimed at verifying the possibility of applying cement by-pass dust (CBPD) in the preparation of alkali-activated materials. The research work was focused on the possibilities of using these wastes for the preparation of small elements of garden architecture. The paper briefly evaluates in particular the results of X-ray diffraction, which were subjected to three types of binder pastes differing in the amount of used activator. In the experiment, a mixture of blast furnace granulated slag, fly ash and cement by-pass dust was alkali activated with sodium metasilicate.

Cancer and infectious diseases are two of the world's major public health problems. Gemcitabine (GEM) is an effective chemotherapeutic agent against several types of cancer. In this study, we developed macrocapsules by incorporating GEM into a chitosan matrix blended with magnetite and zeolite. The physico-chemical characterization of the precursor materials and the new delivery system was carried out by HRTEM-ED, XRD, FESEM-EDS, FT-IR, TGA, encapsulation efficiency (%E.E.) and release profiles at pH 7.4 and 5.0. Cell viability tests on A549 and H1299 cell lines and microbiological properties against staphylococcal strains were performed. Our results revealed the successful production of hemispherical capsules with an average diameter of 1.22 mm, a rough surface and characteristic FT-IR material interaction bands. GEM encapsulation rates exceeded 80%, and release profiles were well-controlled over 24 hours at tested pH levels. Notably, cell viability in H1299 cells was lower than the free GEM control. Moreover, the formulation exhibited potent antimicrobial activity against Staphylococcus epidermidis, highlighting its dual action as a chemotherapeutic and antimicrobial agent. This dual effect underscores the potential of these macrocapsules as innovative delivery system for treating lung cancer in patients who are also at risk of infectious diseases and who are immunosuppressed.

This study aimed to elucidate the antibacterial efficacy and unique chemical compositions generated from plasma-activated water (PAW) when utilized a novel vaginal cleansing device. We conducted an analysis of antibacterial activity against probiotics and several chemical compositions including ions under various operational parameters of PAW, including electrical power (12 and 24 V), treatment duration (1, 10, and 20 min), and stay duration (immediate, 30 and 60 min). Our findings revealed that as treatment duration increased, hypochlorous acid (HOCl), Ca2+, and Mg2+ concentrations increased and Cl−concentrations decreased. Higher electrical power and longer treatment duration resulted in increased HOCl levels, which acts to prevent the growth of general microorganisms. Notably, PAW exhibited no antibacterial effects against a type of probiotic, Lactobacillus reuteri that produces lactic acid for vaginal health. This result demonstrated the ability of the vaginal cleaning device to generate ions, primarily HOCl and some cations (Ca2+ and Mg2+), thereby providing vaginal mucosa protecting and cleansing effects with the vaginal environment.

This work presents the production and incorporation of calcium hydrolyzed nano-solutions at three concentrations (1, 2, and 3 wt.%) in alkali-activated gold mine tailings (MTs) from Arequipa, Perú. A first activator solution of sodium hydroxide (NaOH) at 10M was used. The calcium hy-drolyzed nano-solutions acted as a secondary activator and as additional calcium resource for the alkali-activated materials (AAMs) based on the low-calcium gold MTs. High-resolution trans-mission electron microscopy/energy-dispersive x-ray spectroscopy (HR-TEM/EDS) analyses were carried out to characterize the morphology, size, and structures of the calcium hydrolyzed na-noparticles. Fourier transform infrared (FTIR) analyses then were used to understand the chemical bonding interactions in the calcium hydrolyzed nanoparticles and in the AAMs. Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS) and Quantitative X-ray diffraction (QXRD) were performed to study the structural, chemical, and phase compositions of the AAMs; uniaxial compressive tests evaluated the compressive strength of the reacted AAMs; and Nitrogen adsorption-desorption analyses measured the porosity changes at nanostructure level in the AAMs. The results indicate that each increase in the concentration of the calcium hydrolyzed nano-solution had a direct/proportional effect on the mechanical properties of the AAMs samples. The AAMs with 3 wt.% calcium-hydrolyzed nano-solution had the highest compressive strength value of 15.16 MPa, which represented an increase of 62% compared to the original system without nanoparticles and aged under the same conditions of 70°C for seven days. These results provide useful information about the positive effect of calcium-hydrolyzed nanoparticles on gold MTs and their conversion into sustainable building materials through alkali activation.

The remarkable adsorption capacity of graphene derived materials has prompted their examination in composite materials suitable for deployment in treatment of contaminated waters. In this study, crosslinked calcium alginate – graphene oxide beads were prepared and activated by exposure to pH 4 by using 0.1M HCl. The activated beads were investigated as novel adsorbents for the removal of organic pollutants (Methylene Blue dye and the pharmaceuticals Famotidine and Diclofenac) with a range of physicochemical properties. Effects of initial pollutant concentration, temperature, pH and adsorbent dose were investigated and kinetic models were examined for fit to the data. Maximum adsorption capacities q_max obtained were 1334, 35.50 and 36.35 mg g^-1 for the uptake of Methylene blue, Famotidine and Diclofenac respectively. The equilibrium adsorption had an alignment with Langmuir isotherms while the kinetics were most accurately modelled using a pseudo- first –order and second order models according to the regression analysis. Thermodynamic parameters such as ΔG^◦, ΔH^◦ and ΔS^◦ were calculated and the adsorption process was determined to be exothermic and spontaneous.

A valorization process of spent coffee grounds (SCG) was studied. Thus, a two-stage process, a stage of extraction of the polyphenols and a stage of obtaining activated carbon (AC) by a carbonization process, was performed. The extraction was carried out with a hydro-alcoholic solution in a pressure reactor, modifying time and temperature. To optimize the extraction of polyphenols, a two-level factorial design with three replications at the central values was used. The best results were obtained by performing the extraction at 80 °C during 30 min, using a mixture of EtOH:H2O 1:1 (v/v) as extraction solution. Caffeine and chlorogenic acid were the most abundant compounds in the analyzed extracts, ranging from 0.09 to 4.8 mg∙g^-1 and 0.06 to 9.7 mg∙g^-1, respectively. The precursor obtained in the extraction stage were transformed into AC. An experimental design was realized in order to analyze the influence of different variables in the AC obtained process (reaction time and amount of potassium hydroxide used). Actived carbons with BET specific surface (SBET) comprised between 1600 m^2∙g^-1 and 2330 m²∙g^-1 had a microporous surface. Under the optimum conditions, the obtained AC presented a maximum adsorption capacity of methylene blue (qm) between 411 mg∙g^-1 and 813 mg∙g^-1.

In Parkinson's disease, neuroinflammation is a complex defense mechanism. Activated microglia and Proteinase-activated receptor-2 (PAR2) are key points in the regulation of neuroinflammation. 1-Piperidin Propionic Acid (1-PPA) has been recently described as a novel inhibitor of PAR2. The aim of our study was to evaluate the effect of 1-PPA in neuroinflammation and microglial activation in Parkinson's disease. Protein aggregates and PAR2 expression were analyzed by thioflavin S assay and immunofluorescence in cultured human fibroblasts from Parkinson's patients, treated or not with 1-PPA. A significant decrease of amyloid aggregates and expression of PAR2 were observed after 1-PPA treatment in all patients. A parallel decrease of PAR2 expression, that was higher in sporadic Parkinson’s patients, was also observed both at transcriptional and protein level. In addition, in mouse LPS-activated microglia, the inflammatory profile was significantly downregulated after 1-PPA treatment, with a remarkable decrease of IL-1, IL-6 and TNF-togheter with PAR2 decreased expression.In conclusion, 1-PPA determines reduced neuroglia inflammation and amyloid aggregates formation, suggesting that pharmacological inhibition of PAR2 could be proposed as a novel strategy to control neuroinflammation.

Herein, activated red mud particles are used as an adsorbent for adsorbing phosphorus. Different concentrations of HCl and deionized water are used for desorption tests, and the optimal desorption mechanism is investigated. The Langmuir isothermal model and pseudo-second-order kinetic linear model produce consistent results: the desorption is dominated by the surface desorption of the monomolecular layer, and chemical desorption limits the rate of surface desorption. The desorption thermodynamics indicates that the desorption of phosphorus by the desorbent is spontaneous and high temperature promotes desorption. The particle diffusion model demonstrates that the removal of phosphorus in the form of precipitation from the surface of an activated hematite particle adsorbent occurs primarily via a chemical reaction, and an analysis of the microscopic morphology indicates that the desorption process is primarily accompanied by the dissolution of the metal element Ca, followed by Al and Fe. The desorbent reacts with the active elements in red mud, and the vibration of the [SiO4]2− group calcite or aragonite group of calcium–iron garnet in the functional group disappears. The intensity of the wave peaks of the PO43− groups decreases considerably. Thus, desorption primarily involves the chemical desorption of the monomolecular layer.

Magnetosomes of magnetotactic bacteria consist of magnetic nanocrystals with defined morphologies enclosed in vesicles originated from cytoplasmic membrane invaginations. Although many proteins are involved in creating magnetosomes, a single magnetosome protein, Mms6, can direct the crystallization of magnetite nanoparticles in vitro. The in vivo role of Mms6 in magnetosome formation is debated and the observation that Mms6 binds ferric and not ferrous iron raises the question of how Mms6 could promote the crystallization of magnetite, which contains both ferric and ferrous iron. Here we show that Mms6 is a ferric reductase that reduces ferric to ferrous iron using NADH and FAD as electron donor and cofactor, respectively. Reductase activity is elevated when Mms6 is integrated into either liposomes or bicelles. Analysis of Mms6 mutants suggests that the C-terminal domain binds iron and the N-terminal domain contains the catalytic site. Although Mms6 forms multimers that involve C-terminal and N-terminal domain interactions, a fusion protein with Mms6, which remains a monomer, displays reductase activity, which suggests that the catalytic site is fully in the monomer. These results are consistent with a hypothesis that Mms6, a membrane protein, promotes the formation of magnetite by a mechanism that involves reducing iron.

Actuated carbon (AC) is utilized in various conditions of uses after its disclosure as a solid and dependable adsorbent. A review on AC is introduced along with returning to the wellsprings of AC age; strategies used to produce AC including pyrolysis enactment; actual actuation; synthetic initiation and steam pyrolysis. The significant variables influencing the AC creation, the potential uses of AC and their future possibilities are likewise examined. AC is applied in water, wastewater and leachate medicines in numerous nations, particularly to clean the shading, eliminate the smell and some substantial metals. Taking into account this, an exhaustive rundown of research on compound, physical and organic change strategies of initiated carbon relating to prevent of foreign substance expulsion from watery arrangements was aggregated and investigated. Additionally, the examination of the actual blending strategy and the impregnation technique in enactment with antacid metals shows that the actuated carbon got through actual blending had a higher porosity than the initiated carbon created by the impregnation technique. The uses of initiated carbon items were quickly surveyed.

Transposable elements (TEs) are highly abundant in plant genomes. Environmental stress is one of the critical stimuli that activate TEs. We analyzed a heat-activated retrotransposon named ONSEN in cruciferous vegetables. The multiple copies of ONSEN-like elements (OLEs) were found in all the cruciferous vegetables that were analyzed. The copy number of OLE was abundant in Brassica oleracea, which includes cabbage, cauliflower, broccoli, Brussels sprout, and kale. Phylogenic analysis demonstrated that some OLEs transposed after the allopolyploidization of parental Brassica species. Furthermore, we found that the increasing number of OLEs in B. oleracea appeared to be induced transpositional silencing by epigenetic regulation, including DNA methylation. The results of this study would be relevant to the understanding of evolutionary adaptations to thermal environmental stress in different species.

Food saving and further valorization is of major interest in our days. Worldwide, scientists intensify their efforts to increase shelf life of products due to the global danger of coming food crisis. Even though many chemicals could achieve such target, the circular economy spirit and the global trend against the greenhouse effects impose the turn of research activities using environmentally friendly biomass materials, biowastes, and biodegradable materials. In this study, the promising biopolymer chitosan incorporated with the promising biodegradable polymer poly-vinyl-alcohol to produce a biopolymeric matrix. This biodegradable biopolymer was further mixed homogeneously with 15% thymol/nano-zeolite nanohybrid material and the final developed film was extremely improved compared to the relevant of chitosan/poly-vinyl-alcohol film. Mechanical properties were increased significantly i.e., 34% for Young Modulus and 46,5% for ultimate tensile strength, while the antioxidant activity increased by 53,4%. The antibacterial activity increased by 134% for Ecoli, 87,5% for Saureus, 32% for Lmonocytogenes, and 9% for Senterica. The water-vapor diffusion coefficient and the oxygen permeability coefficient decreased down to -51% and -74% respectively, and thus the water-vapor and oxygen barrier increased. In-vivo experiments on strawberries show an extension of 233% for shelf-life duration which resulted from the modified atmosphere by the control-released thymol.

A large number of microplastics (MPs) have been found in various stages of wastewater treatment plants, which may affect the functional microbial activity in activated sludge and lead to unstable pollutant removal performance. In this study, the effects of different concentrations of polylactic acid microplastics (PLA MPs) on system performance, nitrification and phosphorus (P) removal activities, and extracellular polymeric substances (EPS) were evaluated. The results showed that under the same influent conditions, low concentrations (50 particles/(g TS)) of PLA MPs had no significant effect on effluent quality. The average removal efficiencies of chemical oxygen demand, phosphate and ammonia were all above 80%, and the average removal efficiencies of total nitrogen remained above 70%. High concentrations (200 particles/(g TS)) of PLA MPs inhibited the activities of polyphosphate accumulating organisms (PAOs) and nitrifying bacteria. The specific anaerobic P release rate decreased from 37.7 to 23.1 mg P/(g VSS·h), and the specific aerobic P uptake rate also decreased significantly. The specific ammonia oxidation rate decreased from 0.67 to 0.34 mg N/(g VSS·h), while the change in specific nitrite oxidation rate was not significant. The dosing of PLA MPs decreased the total EPS and humic acid content. As the concentration of PLA MPs increased, microbial community diversity increased. The relative abundance of potential PAOs (i.e., Acinetobacter) increased from 0.08% to 12.57%, while the relative abundance of glycogen accumulating organisms (i.e., Competibacter and Defluviicoccus) showed no significant changes, which would lead to improved P removal performance. The relative abundance of denitrifying bacteria (i.e., Pseudomonas) decreased from 95.43% to 58.98%, potentially contributing to the decline in denitrification performance.

Concrete is the most commonly used construction material due to its various advantages, such as versatility, familiarity, strength and durability and it will continue to be in demand far into the future. However, with today’s sensitivity to the environmental protection, this material is facing unprecedented challenges due to its high greenhouse gas emission mainly during cement production. This paper investigates one of the promising cement replacement materials, alkali activated cement (AAC) concrete. Being produced mainly from byproduct materials and having a comparable structural performance to conventional concrete, AAC concrete has a potential to transform the construction industry. Mechanical properties such as compressive and flexural strength and the relationship between them are studied. Different source materials such as fly ash (FA), ground granulated blast furnace slag (GGBS), silica fume (SF) and Metakaolin (MK) are used. The effect of the source materials and the activator solutions on the concrete performance is studied. Furthermore, the freeze-thaw resistance of the concrete is studied. The results of the study showed that the behavior of AAC depends highly on the source material combinations as well as type used. The effect of the alkaline solution is also dependent on the source material used. Mixes with higher GGBS content in general showed the highest strength while mixes with MK showed the highest flexural strength. The results from the freeze-thaw test showed that proper design of AAC concrete with a lower water content is critical to achieve a good resistance.

Biomass is a widely distributed and renewable source of carbon. The main objective of this work is to produce an activated carbon from coconut shells with suitable characteristics to separate CO2 from biogas. The textural characterization of the adsorbent has been determined. Pure component adsorption isotherms of CO2 and CH4 at 30, 50 and 70 °C have been measured. Moreover, the performance of the produced activated carbon, as potential adsorbent for CO2 capture from a CO2/CH4 gas mixture has been evaluated under dynamic conditions in a purpose-built fixed-bed setup.

The development of novel porous composite materials for organic dye degradation and removal has received increasing attention due to water contamination problem. In this paper, hydrothermal synthesized nano zeolite A have been encapsulated with porous periodic mesoporous organosilica (PMO) through a simple modified StÖber method an organosilane-directed growth-induced etching strategy, the obtained yolk-shell structured sample was further functionalized by the impregnation of copper, realizing the composite material with hierarchical porous and catalytic properties. The morphology, porosity and metal content of the zeolite Cu/A and Cu/A@Et-PMO were fully characterized. As compared to the parent material, the composite Cu/A@Et-PMO have an efficient adsorption and catalytic degradation performance on methylene blue (MB), the removal efficiency reached as high as 95% of 60 mg/L MB with 10min. These novel structured porous composites may have great potential for adsorption and degradation application including waste effluents.

Over the past decade, the production of biofuels from lignocellulosic biomass has steadily increased to offset the use of fuels from petroleum. To make biofuels cost-competitive, however, it is necessary to add value to the “ligno-” components (up to 30% by mass) of the biomass. The properties of lignin, in terms of molecular weight (MW), chemical functionality, and mineral impurities often vary from biomass source and biorefinery process, resulting in a challenging precursor for product development. Activated carbon (AC) is a feasible target for the lignin-rich byproduct streams because it can be made from nearly any biomass and it has a market capacity large enough to use much of the lignin generated from the biorefineries. However, it is not known how the variability in the lignin affects the key properties of AC, because until now, they could not be well controlled. In this work, various fractions of ultraclean (< 0.6 % ash) lignin are created with refined MW distributions using Aqueous Lignin Purification using Hot Agents (ALPHA) and used as precursors for AC. AC is synthesized via zinc chloride activation and characterized for pore structure and adsorption capacity. We show that AC surface area and the adsorption capacity increase when using lignin with increasing MW, and furthermore, that reducing the mineral content of lignin can significantly enhance the AC properties. The surface area of the AC from the highest MW lignin can reach ~1830 m2/g (absorption capacity). Furthermore, the single step activation carbonization using zinc chloride allows for minimal carbon burnoff (< 30%) capturing most of the lignin carbon compared to traditional burn off methods in biorefineries for heat generation.

The escalating global demand for clean water has propelled research into sustainable and cost-effective purification methods. Activated carbon (AC) derived from biowaste materials presents an environmentally friendly and economically viable solution for water treatment. This review article provides an extensive overview of the synthesis techniques, characterization methods, and applications of biowaste activated carbon (BAC) for water purification. It discusses the diverse sources of biowaste, such as agricultural residues, food waste, and biomass, and explores various activation methods including physical, chemical, and biological processes. Furthermore, the article examines the adsorption mechanisms, performance factors, regeneration strategies, and emerging trends in BAC synthesis and application. Insights from this review can guide future research endeavors and facilitate the development of sustainable water purification technologies.

Activated Corrosion Products (ACPs) formation and deposition pose a critical safety issue for nuclear fusion reactors. The working fluid transports the ACPs towards regions accessible to worker personnel. Predicting ACPs formation deposition and transport is fundamental for source term identification, reduction of radiation exposure assessment, maintenance plan definition, design optimization, and waste management. The code OSCAR-Fusion has been developed by the CEA (France) to evaluate the ACPs generation and transport in closed water-cooled loops for fusion application. This work aims at assessing the impact of water chemistry on the transport, precipitation, and deposition of corrosion products for the EU-DEMO divertor Plasma Facing Unit Primary Heat Transfer System. Sensitivity analyses and uncertainty quantification are needed due to the multi-physics phenomena involved in ACPs formation and transport. The OSCAR-Fusion/RAVEN code coupling developed by the Sapienza University of Rome and ENEA has been used. This work presents the perturbation results of different parameters chosen for a closed water-cooled loop considering a continuous scenario of 1888 days. The aim of this work is to assess the variation of build-up of ACPs, perturbing the alkalizing agent concentration into the coolant and the corrosion and release rates of different materials.

An activated carbon manufacturing process using winemaking waste is analyzed and designed at industrial scale. Starting from experimental research, the chemical transformations and thermodynamics during pruning wood conversion are studied as a basis for plant design. In this way, mass and energy balances of hydrothermal carbonization and physical activation are fulfilled and a thermoeconomic methodology is applied to develop an energy-integrated plant. To achieve this target, a network of heat exchangers is allocated to minimize heat consumption and supply hot domestic water, while a cogeneration cycle is designed to provide electricity and satisfy the remaining heat demand. Furthermore, a sensitivity analysis is carried out to determine the influence of the production scale and other operation parameters, such as annual workload, service life, and capital and feedstock costs, on the economic viability of the plant. The energy balance of the plant indicates that the energy integration design manages to provide 48.9% of the overall process energy demand by crossing hot and cold streams and recovering heat from residual flue gas. On the other hand, the exergy cost analysis identifies the combustion of pruning wood used to provide heat demands as the main source of exergy destruction, confirming the suitability of integration to improve the thermodynamic performance. Including activated carbon production, electricity, and hot domestic water, the exergy efficiency of the plant stands at 11.5%.

The sustainable development of innovative eco-friendly multifunctional nanocomposites, possessing superior characteristics, is a noteworthy topic. Novel semi-interpenetrated nanocomposite films based on poly(vinyl alcohol) covalently and thermally crosslinked with oxalic acid (OA), reinforced with a novel organophosphorus flame retardant (PFR-4) derived from co-polycondensation in solution reaction of equimolar amounts of co-monomers, namely, bis((6-oxido-6H-dibenz[c,e][1,2]oxaphosphorinyl)-(4-hydroxyaniline)-methylene)-1,4-phenylene, bisphenol S, and phenylphosphonic dichloride, in a molar ratio of 1:1:2, and additionally doped with silver-loaded zeolite L nanoparticles (ze-Ag), have been prepared by casting from solution technique. The morphology of the as prepared PVA-oxalic acid films and their semi-interpenetrated nanocomposites with PFR-4 and ze-Ag was investigated by scanning electron microscopy (SEM), while the homogeneous distribution of the organophosphorus compound and nanoparticles within the nanocomposite films has been introspected by means of energy dispersive X-ray spectroscopy (EDX). It was established that composites with a very low phosphorus content had noticeably improved flame retardancy. The peak of the heat release rate was reduced up to 55%, depending on the content of the flame retardant additive and the doping ze-Ag nanoparticles introduced into the PVA/OA matrix. The ultimate tensile strength and elastic modulus increased significantly in the reinforced nanocomposites. Considerably increased antimicrobial activity was revealed in the case of the samples containing silver-loaded zeolite L nanoparticles.

In potato, high levels of nitrogen (N) can lead to excessive vegetative growth at the expense of tuber development, resulting in lower yield and poor quality tubers. We found that Solanum tuberosum CLE4 (StCLE4) is expressed most strongly in the roots on N-rich media and positively regulates root growth of potato in N-deficient conditions. We noted that StCLE4 functions as a negative regulator of normal shoot apex development similar to CLV3 in Arabidopsis. Transcriptomic analysis revealed that overexpression of StCLE4 results in repression of the StIT1 gene, a regulator of potato tuber initiation. Overexpressing StCLE4 stolons were transformed into branches that were similar to milder it1 phenotype. We also found that NIN-like proteins, key regulators of nitrate signaling, bind to the regulatory sequence of StIT1 in yeast one-hybrid assay. Taken together, our findings suggest that StCLE4 regulates shoot, root and stolon growth in potato.

Fabrics comprised of porous fibers could provide effective passive protection against chemical and biological (CB) threats whilst maintaining high air permeability (breathability). Here, we fabricate hierarchically porous fibers consisting of regenerated silk fibroin (RSF) and activated-carbon (AC) prepared through two fiber spinning techniques in combination with ice-templating – namely cryogenic solution blow spinning (Cryo-SBS) and cryogenic wet-spinning (Cryo-WS). The Cryo-WS RSF fibers had exceptionally small macropores (as low as 0.1 µm) and high specific surface areas (SSAs) of up to 79 m2 g-1. The incorporation of AC could further increase the SSA to 210 m2 g-1 (25 wt. % loading) whilst also increasing adsorption capacity for volatile organic compounds (VOCs).

The annual construction and demolition waste (CDW) generated from EU construction sector was 850 million tons, which represented 31% of the total waste generation and about 28% of CDW was ceramics (bricks and tiles). In this study, the feasibility of using CDW brick powder as the precursor of alkali activated mortar (AAM) and extruded polystyrene (XPS) as the lightweight aggregates to form lightweight brick powder AAM (LW-BP-AAM) for non-structural applications was investigated. The thermal conductivity of LP-BPAAM was 0.112 W/m·K with density of about 1,135 kg/m³ which was lower than the counterparts with similar density in literature. The acid resistance of LW-BP-AAM is comparable to conventional fly ash based AAM and superior than ordinary Portland cement. From the scanning electron microscopy with energy dispersive X-ray spectroscopy, there was no severe damage on the surface of LW-BP-AAM but aluminate was removed from the matrix which was further verified in Fourier transform infrared spectroscopy. The mass and strength loss of LP-BP-AAM was 1.5% and 33%, respectively. Although the compressive strength of the LP-BP-AAM was low (about 1.8 MPa), it can be improved by optimising the particle size of the XPS aggregates.

: Alluvial soils naturally possess abundant soil nutrients. Nevertheless, excessive nitrogen addition and inappropriate use of nitrogen fertilizers lead to conditions where soil nutrients become immo-bilized, ultimately reducing productivity. This study investigates the potential of natural nano-material zeolite which is important land resources to improve nutrient utilization efficiency and mitigate the harmful effects of excessive fertilizer application. Specifically, the research ex-plores the incorporation of clinoptilolite zeolite and processed sewage sludge blends, alongside reduced recommended nitrogen fertilizer doses, to evaluate their impact on soil quality and plant growth. A greenhouse experiment was conducted (three-year study), comprising eight treatments with varying proportions of zeolite and sewage sludge. The efficacy of these treatments in en-hancing soil carbon pools, nutrient indices, and plant growth responses was assessed. Results in-dicate that a combination of 50% recommended fertilizer dose, 4-6% zeolite, and 5-10% sewage sludge significantly improved multiple aspects of plant growth, including leaves, tillers, culms, and panicles, leading to increased straw and grain yields. The addition of 6% zeolite in conjunc-tion with sewage sludge positively influenced plant tillering capacity. Certain treatment combina-tions exhibited a greater impact on plant height at different growth stages. For example, the treatment with 75% recommended fertilizer dose, 4% zeolite, and 5% sewage sludge significantly affected plant height at 40 and 55 days after treatment. Additionally, the combination of 50% recommended fertilizer dose, 6% zeolite, and 10% sewage sludge promoted plant height, carbon levels, and various yield parameters in later stages. Principal component analysis effectively dis-tinguished treatments incorporating zeolite and sewage sludge based on plant responses. The combination of 6% zeolite and 10% sewage sludge, along with a 50% recommended fertilizer dose, positively influenced soil carbon fractions, nutrient levels, and the growth response of rice plants.

Ti-aluminosilicate gels were used as supports for immobilization of Fe, Co and Ni oxides (5%) by impregnation, and synthesis of efficient photocatalysts in degradation of β-lactam antibiotic from water. Titanium oxide (1 and 2%) was incorporated into zeolite network by modifying the gel during the zeolitation process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction and optical properties were studied by X-ray difraction, H2-TPR, XPS, Raman, photoluminiscence and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetra-coordinate Ti4+ sites. The immobilized metals from group VIII are both in the form of metal oxides such as Fe2O3, Fe3O4, CoO, Co3O4 , NiO and also in the me-tallic state (Fe0, Co0, and Ni0). A red shift of the absorption edge was observed in UV-Vis spectra of photocatalysts upon addition of Fe, Co or Ni species. The photocatalytic performances were evaluated in degradation of cefuroxime from water under visible light irradiation. The best results were obtained for iron immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

An attempt to investigate the effect of binary composite activators on the microstructure of fly ash-based geopolymers is conducted through the comparison of 24 experiments, which consisted of Na2SiO3•9H2O, Na2CO3, K2CO3, NaOH, and KOH through a facile preparation technique. The results show that the activator of Na2SiO3•9H2O+KOH presents the highest mechanical strength, due to the synergy activation between the inherent ≡Si-O-Si≡ chains derived from Na2SiO3 and K+’s catalysis. It reveals that the K+ plays a crucial role in Na2SiO3-activated fly ash geopolymer, which is the rate-determining step of the enhanced crosslinking and propagation of N-(C)-A-S-H chains, leading to an increase in weight loss temperatures of specimens from TG/DTG results. Furthermore, the adding silica fume facilitates as-formed amorphous silicates, which also could fill into the pores of N-(C)-A-S-H amorphous gels and present a uniform and compact morphology, leading to an increase in the pore volume of the pore diameter less than 100 nm. It explores an efficient and cost-effective preparation of fly ash-based geopolymer for developing solid-waste recycling techniques.

This paper describes the influence of the regeneration treatments on 4-chloro-2-methyl-phenoxyacetic acid (MCPA)-loaded activated carbons (ACs) on adsorption-desorption cycles with two commercial ACs, Merck and Norit 1240 X ( Norit 1240 X was used in a granular and powder form). The ACs were saturated with MCPA and then submitted to four regeneration cycles, by washing with ethanol, NaOH solutions and washed with NaOH solutions followed by a thermal treatment. The ACs regenerated with ethanol showed a better performance concerning the successive adsorption-desorption cycles. On the first cycle, the MCPA desorbed, from washing with ethanol, from all ACs was higher than 99%. After a fourth adsorption-desorption cycle, washing regeneration combined with thermal treatment allowed excellent regeneration results. The amount of MCPA adsorbed on Norit 1240 X AC was higher than the amount adsorbed in the first cycle. MCPA adsorption kinetic data were analyzed by applying pseudo-first-order, pseudo-second-order, and Weber-Morris models. The pseudo-second-order fit better fit to the data and the Weber-Morris representation allows confirming that on Norit 1240 X, in a granular form, the pore diffusion was the limiting factor concerning the MCPA adsorption.

Common bean (Phaseolus vulgaris L.) is an important crop for food security and for national economics for several countries worlwide. One of the most important factors of risk in common bean production is the fungal disease anthracnose caused by Colletotrichum lindemuthianum, which in some cases, causes complete yield losses; this kind of plant disease is usually managed through the application of chemical products such as fungicides, that are commonly not accepted by society, this rejection is based on the relationship of pesticides with health damage and environmental contamination. In order to help in solving this drawbacks, the present work propose the use of Electrochemically Activated Salt Solutions(EASS) as a safer pathogen control agent in crops due to it have shown an elicitor and biostimulant effect on plants such as tobacco and apple. With this background, this manuscript presented in vitro results of the evaluation of the inhibitory effect for multiple bean pathogens and in vivo results of EASS in the common bean-Colletotrichum pathosystem by in vitro evaluations of the inhibitory effect for multiple bean pathogens and in vivo evaluation of the infection severity and defense activation such as secondary metabolites production and antioxidant activity. EASS presence in growth media had strong inhibitory effect, at beginning of experiment, for some of the evaluated fungi. EASS showed effect against the development of the disease when applied in specific doses to prevent distress in plants.

This article deals with the possibility of partial replacement of blast furnace slag with fly ash after denitrification by the Selective Non-Catalytic Reduction (SNCR) method in alkali-activated materials. In the experiment, the basic physical-mechanical properties and durability properties were tested, the hydration reaction was monitored in a calorimeter and infrared spectroscopy was performed. Results were compared between mixtures prepared with fly ash without denitrification and also with reference mixture based only on alkali-activated blast furnace slag. The basic result is the finding, that hybrid alkali-systems with fly ash after denitrification show similar trends as hybrid alkali-systems with fly ash without denitrification. The significant effect of fly ash is manifested especially in terms of resistance to freeze-thaw. The reactions in the calorimeter show a slower development of reactions with increasing replacement of slag by fly ash. In the case of testing resistance to leaching in demineralised water, a decrease of flexural strength was found, which corresponds to the conclusions of strength testing, that long-term deposition of bodies in water causes deterioration of mechanical properties.

Influence of particle size on the mechanical strength of alkali activated material from waste refractory monolithic was investigated in this study. Precursor was chemically and mineralogically analysed, separated on 4 fractions and alkali activated with Na-water glass. Alkali activated materials were thoroughly investigated under SEM and XRD to evaluate the not predicted differences in mechanical strength. Time dependence of curing temperature on mechanical strength was investigated in the sample prepared from a fraction that caused the highest compressive strength.

Hypothesis: Anti-diabetic drugs modulate p-21 activated kinase (PAK) signaling Introduction: Type 2 diabetes mellitus (T2DM) is a chronic inflammatory disease associated with increased cancer risk. PAK signaling is implicated in cellular homeostasis when regulated, and cancer when unrestrained. Recent reports provided a role for PAK signaling in glucose homeostasis, but the role of PAKs in the pathogenesis of T2DM is unknown. Here we performed a mini-meta analysis to explore if anti-diabetic drugs modify PAK signaling pathways, and provide insight regarding modulation of these pathways to potentially reduce diabetes-associated cancer risk. Methods: PAK interacting partners in T2DM were identified using online STRING database. Correlation studies were performed via systematic literature review to understand the effect of anti-diabetic drugs on PAK signaling. Mini meta analysis correlated multiple clinical studies and revealed the overall clinical response rate and percentage of adverse events in piogliazone (n=53) and metformin (n=91) treated patients with PAK-associated diseases. Results: A total of 30 PAK interacting partners were identified (10: reduced beta-cell mass; 10: beta-cell dysfunction; 10: obesity-insulin resistance) which were highly associated with Wnt, and G-protein signaling. Anti-diabetic drug metformin activated signaling pathways upstream; whereas pioglitazone inhibited pathways downstream of PAK. Overall clinical response upon pioglitazone treatment was 53%. 79% of pioglitazone and 75% of metformin treated patients had adverse events. Pioglitazone reduced molecular-PAK biomarkers of proliferation (Ki67 and CyclinD1), and metformin had the opposite effect. Conclusions: PAK signaling in T2DM likely involves Wnt and G-protein signaling which may be altered by anti-diabetic drugs metformin and pioglitazone. Apart from the therapeutic limitations of adverse events, pioglitazone may be promising in chemoprevention, however long-term multi-centered studies, which initiate pioglitazone treatment early will be required to fully assess the full potential of these drugs.

Hypothesis: Anti-diabetic drugs modulate p-21 activated kinase (PAK) signaling Introduction: Type 2 diabetes mellitus (T2DM) is a chronic inflammatory disease associated with increased cancer risk. PAK signaling is implicated in cellular homeostasis when regulated, and cancer when unrestrained. Recent reports provided a role for PAK signaling in glucose homeostasis, but the role of PAKs in the pathogenesis of T2DM is unknown. Here we explored whether PAK signaling should be targeted via chemoprevention to reduce diabetes-associated cancer risk. Methods: PAK interacting partners in T2DM were identified using online STRING database. Systematic literature review provided the effect of anti-diabetic drugs on PAK signaling. Review of clinical studies revealed the overall clinical response rate and percentage of adverse events in piogliazone (n=53) and metformin (n=91) treated patients with PAK-dependent diseases. Results: A total of 30 PAK interacting partners were identified (10: reduced beta-cell mass; 10: beta-cell dysfunction; 10: obesity-insulin resistance) which were highly associated with Wnt, and G-protein signaling. Anti-diabetic drug metformin activated signaling pathways upstream; whereas pioglitazone inhibited pathways downstream of PAK. Overall clinical response upon pioglitazone treatment was 53%. 79% of pioglitazone and 75% of metformin treated patients had adverse events. Pioglitazone reduced molecular-PAK biomarkers of proliferation (Ki67 and CyclinD1), and metformin had the opposite effect. Conclusions: PAK signaling in T2DM involves Wnt and G-protein signaling which is altered by anti-diabetic drugs metformin and pioglitazone. Apart from the therapeutic limitations of adverse events, pioglitazone is promising in chemoprevention, however long-term multi-centered studies, which initiate pioglitazone treatment early will be required to fully assess the full potential of these drugs.

Calcium-activated chloride secretion in epithelial tissues described for many years. However, the molecular identity of the channel responsible for the Ca2+-activated Cl− secretion in epithelial tissues has remained a mystery. More recently, TMEM16A has been identified as a new putative Ca2 -activated Cl- channel (CaCC),. The primary goal of this article will be to review the characterization of TMEM16A, as it relates to the physical structure of the channel, as well as, important residues that confer voltage and Ca2+-sensitivity of the channel. This review will also discuss the role of TMEM16A in epithelial physiology and potential associated-pathophysiology. This will include discussion of developed knockout models that have provided much needed insight on the functional localization of TMEM16A in several epithelial tissues. Finally, this review will examine the implications of the identification of TMEM16A as it pertains to potential novel therapies in several pathologies.

Biomass is a promising alternative and renewable energy source that can be transformed into other value-added products such as activated carbon. In this research, barley husk, corn cob and Agave salmiana leaves were characterized to determine their chemical composition and morphology to evaluate their potentiality as precursors of activated carbons. Based on the main composition results obtained, the biomass samples have suitable chemical and physical characteristics to be considered as good precursors of activated carbons, such as carbon contents greater than 40%, ash content less than 10%, moisture content less than 30%, high volatile contents with values from 75 to 80% and a porous and fibrous morphology. The results indicate that the main compositions in the biomass were cellulose and lignin. The cellulose content was more than lignin (15–26%) for the residues selected. Specifically, a-cellulose contents with values from 52% to 79%, β-cellulose contents of 13–44%, γ-cellulose contents less than 11%, and holocellulose contents of 82–83% were determined. The thermal decomposition for the biomass samples proceeded with five stages attributed to the evaporation of some volatile compounds (70–150 ºC), to the degradation of hemicellulose (180–230 ºC), to the cellulose volatilization (250–350 ºC), to the lignin decomposition (380–550 ºC), and to the degradation of complex polymers and inorganic salts, respectively. The stage corresponding to the cellulose decomposition showed rapid mass decreased in the three residues. This results show that the cellulose and lignin content is another important parameter to evaluate the pyrolysis characteristics of a good precursor of activated carbon.

Calcium-activated potassium channels (KCa) are the important participants in calcium signaling pathways due to their ability to be activated by increase of the intracellular free calcium concentration. KCa channels are involved in the regulation of various processes in the cells under normal, as well as pathophysiological conditions, including oncotransformation. Previously, with the use of patch-clamp method, we registered the KCa activity in the plasma membrane of human myeloid leukemia K562 cell line. Here, we performed the molecular and functional identification of KCa channels and have uncovered their role in proliferation, migration and invasion of K562 cells. Using a combined approach, we identified the functional activity of SK2, SK3 and IK channels in the plasma membrane of the cells. Selective SK and IK channel inhibitors, apamin and TRAM-34, reduced the proliferative, migratory and invasive capabilities of human myeloid leukemia cells. At the same time, the viability of K562 cells was not affected by KCa channel inhibitors. Our data imply that SK/IK channel inhibitors could be used to slow down the proliferation and spreading of leukemia cells that express functionally active KCa channels in the plasma membrane.

Water microbial contamination is a serious issue that poses a risk to both animal and human health. 120 water samples collected from main water source and drinkers from a poultry farm. Different bacterial pathogens were isolated from water sources. Escherichia (E.) coli, Pseudomonas (P.) aureoginosa, (Salmonella) S. Typhimurim, Aeromonas (A.) hydrophila at different percentages. Variable degree of bacterial resistance to some commercial disinfectants commonly used to disinfect water system (iodine, terminator and H2O2). Nanoparticles were used to control bacteria in water. About the safety investigation for the prepared nanomaterials, the work results demonstrated that zinc oxide (ZnO) nanoparticles (NPs) exhibit the highest safety profile among the manufactured materials. The median fatal dose (LD50) for ZnO NPs was determined to be 3709 mg/kg body weight. In comparison, the LD50 values for zeolites and nanocomposites were 3251 mg/kg and 2658 mg/kg, respectively. Therapeutic dosages were estimated based on the LD50. Zeolite NPs, ZnO NPs and ZnO/zeolite NPs showing promising results in control of those bacteria. It was concluded that the escalating resistance of bacteria to disinfectants have led to a need to find alternative such as nanoparticles that proved promising results in control of pathogens, particularly it showed a safe effect on laboratory animals.

In the last decades, studies on the inflammatory signaling pathways in multiple pathological contexts revealed new targets for novel therapies. Among the family of G-protein-coupled Proteases Activated Receptors, PAR2 was identified as a driver of the inflammatory cascade in many pathologies, ranging from autoimmune disease to cancer metastasis. For this reason, many efforts have been focused on the development of potential antagonists of PAR2 activity. This work focuses on a small molecule, 1-Piperidine Propionic Acid (1-PPA), previously described to be active against inflammatory processes, but whose target is still unknown. Stabilization effects observed by cellular thermal shift assay coupled to in-silico investigations, including molecular docking and Molecular Dynamics simulations, suggested that 1-PPA binds PAR2 in an allosteric pocket of the receptor inactive conformation. In addition, this compound was found able to inhibit platelet aggregation, a process mediated by PAR family members, including PAR2. Since the allosteric pocket binding 1-PPA is highly conserved in all the members of the PAR family, the evidence reported here suggests that 1-PPA could represent a promising new small molecule targeting PARs with antagonistic activity.

Food waste disposal to landfills practice contributes to greenhouse problem due to the emission of gases such as methane to the atmosphere. Shelf-life extension of food products and further valorization of food wastes such as the conversion to activated carbon are tested nowadays as alternative techniques. The development and use of biobased active coatings against food oxidation/bacterial deterioration is an environmentally friendly technique. In this study, a novel food active coating was successfully developed based on a chitosan (CS)/poly-vinyl alcohol (PVOH) matrix activated with a nanohybrid of natural thymol (TO) adsorbed in activated carbon (AC) derived from spent coffee. The results shown that, compared to the pure CS/PVOH polymeric matrix, the coating with 15% wt. TO@AC nanohybrid concentration achieved +23.5 % Young’s modulus value, +20.1% ultimate strength value, increased barrier of +50.2% for water and +74.0 % for oxygen, +69.0% antioxidant activity, increased antibacterial activity of +5.5% against Escherichia coli, +17.8% against Salmonella enterica, +42.5% against Staphylococcus aureus, and +2.5% against Listeria monocytogenes. A visual evaluation of this coating shown a delay to fresh bananas enzymatic browning and significantly decrease their weight loss. This indicates that it could be potentially used to extend the shelf-life of fresh fruits.

Steel slag is a co-product of the steelmaking industry, this material is rarely used as a binder due to its low cementitious properties. Thus, it´s believed that the alkaline activation of steel slag can enable its use as a cementitious material. This work has the objective of making a systematic bibliographic review on the theme "slag melt as a precursor in activated alkali binders". To this end, the ProKnow-C method was used for the selection and analysis of relevant research on the topic. The portfolio resulted in 71 texts, mostly journals paper. Bibliometrics showed that the country with the most publications is China and the journal with the most publications is Construction and Building Materials. The critical analysis concluded that the XRD, XRF, and compressive strength tests are the most used for the characterization of the material. It is possible to establish that there are some knowledge gaps on the subject, such as better mechanical characterization and greater production of works with dosing by the one-part method.

Antibiotics are among the most critical environmental pollutant drug groups. One of the methods used to remove this pollution is adsorption. In this study, activated carbon was produced from the pumpkin seed shell and then modified with KOH. This adsorbent obtained was used in the re-moval of ciprofloxacin from aqueous systems. Fourier Transform-Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy (SEM), elemental, X-ray Photoelectron Spectroscopy (XPS), Brunauer-Emmett-Teller (BET) and Zeta analyzes were used for the characterization of the ad-sorbent. In particular, the surface area was found to be a very remarkable value of 2730 m2/g. The conditions of the adsorption experiments were optimized based on interaction time, adsorbent amount, pH and temperature. Over 99% success has been achieved in removal works carried out under the most optimized conditions. In addition, it was determined that the Langmuir isotherm is the most suitable model for the adsorption interaction.

Due to rapid urbanization, the quantity of wastewater treatment plants (WWTP) has increased, and with it the amount of waste generated by them. Sustainable management of this waste can lead to the creation of energy-rich biogas through the fermentation process. This review presents recent advances in the anaerobic digestion process resulting in greater biogas production. Disintegration techniques for enhancing waste activated sludge fermentation can be generally partitioned into biological, physical and chemical, each of which are covered in this review. These disintegration techniques were compared mainly in terms of their biogas yield. It was found that ultrasonic and microwave disintegration provides the highest biogas yield (>500%); however, they are also the most energy demanding (>10,000 kJ kg-1 total solids).

Synthesis of activated carbon from waste biomass is of current interest towards sustainability. The properties of biomass derived activated carbon largely depends on the carbonization process. This study reports preparing extremel high surface area mesoporous activated carbon from hemp bast fibre using hydrothermal processing. Processing in hot water (390-500^oC), then activation using KOH and NaOH was investigated at different loading ratios. The described approach was found to enhance the mesoporosity (centered at 3.0 to 4.5 nm) of the hemp derived activated carbon (HAC) from activation (confirmed by BJH pore size distribution and TEM imaging). BET results showed that the product has an extremely high surface area (2425 m²/g) while the surface functional groups (-OH, COOH, C=C/C-C) were confirmed and quantified by XPS and FTIR results. Increasing KOH concentration was found to enhance the surface area with an optimum biochar to KOH ratio of 1:3. The crystallite domain size of HAC was determined using Raman spectroscopy of different wavelengths. The procedure described in this study is an environmentally friendly scalable route for the mass production of activated carbon using hemp fiber.

Cement-free concrete has superior physical performance, such as strength and durability, compared to OPC concrete, however, it has the disadvantage of large shrinkage. Large shrinkage can cause cracks due to shrinkage stress in the long term. In this study, a shrinkage reducing agent (SRA) was used to reduce the shrinkage of cement-free mortar; its content was increased from 0.0 to 1.5 %. For an SRA content of 1.0 %, a calcium sulfoaluminate (CSA) expansive additive (EA) (2.5, 5.0, and 7.5%) was added. To calculate the shrinkage stress of cement-free mortar using the SRA and EA, the compressive strength, elastic modulus, and total and autogenous shrinkage were measured. The unit shrinkage stress of cement-free mortar was obtained by multiplying the elastic modulus by the length change and accumulated to obtain the shrinkage stress acting on the mortar according to the age. The shrinkage stress of cement-free mortar showed different tendencies as the age increased. At early ages, the shrinkage rate of the mortar occupied a large proportion of the shrinkage stress. In the long term, the shrinkage stress was significantly affected by the elastic modulus. As a result, SRA was found to be effective in reducing the shrinkage stress by decreasing both the elastic modulus and shrinkage. However, EA increased the shrinkage stress over the long term due to an increase in elastic modulus even though it compensated for early-ages shrinkage.

Continuous cropping of Platycodon produces problems that significantly impact its yield and quality making it a pressing issue that requires immediate attention. In this study, the sandwich method is employed to evaluate the allelopathic activity of different plant parts (leaves, stems, and roots) of Platycodon. The inhibitory effects of the various Platycodon plant parts were quantified based on their effects on lettuce seedlings growth by Sandwich method, with the following average inhibition percentages at 1 mg/ml (agar) of : leaves (79.4%, 61.8%), stems (58.0%, 45.7%), and roots (53.4%, 49.3%) for lettuce radicals and hypocotyls, respectively. At a concentration of 5 mg/ml, the inhibitory effects were as follow: leaves (91.9%, 72.2%), stems (79.5%, 60.3%), and roots (71.4%, 65.2%). Also, by employing the Plant Box method, it was determined that Platycodon root exudation. The growth inhibition rates of lettuce seedling roots and hypocotyls were 45.5% and 18.9%, respectively. The effect of activated carbon on the adsorption of allelopathic substances was investigated, and the results of the sandwich method with a concentration of 1 mg/ml showed the following growth inhibitory effects on lettuce seedlings and hypocotyls: roots (27.8%, 25.7%), leaves (13.3%, 25.7%), and stem (9.07%, 13.6%). The Plant Box method revealed average rates of inhibition of -16.7% and -4.70% on the growth of lettuce seedlings and hypocotyls, respectively. The results of this study demonstrated that activated carbon has a mitigating effect on the allelopathic inhibition associated with the different plant parts and root exudation of Platycodon, thus may provide a potential solution for overcoming obstacles associated with continuous cropping of Platycodon.

In this study, Plasma-Activated Water (PAW) was synthesized using a coaxial Dielectric Barrier Discharge (DBD) reactor, benefiting from the elevated capacity of air-flow-assisted DBD discharges to enhance nitrogen-based species concentration. By manipulating operational parameters, including gas flow rate, activation time, and DI water volume, we achieved significant concentrations of Reactive Oxygen and Nitrogen Species (RONS). As a result, the PAW obtained displayed pronounced physicochemical attributes: a pH of 2.06, an ORP of 275mV, conductivity of 3mS/cm, and TDS of 1200 mg/L. A pivotal aspect of this research was the evaluation of the reactor's efficiency, as indicated by metrics like the specific input energy and ozone efficiency yield. The antimicrobial potential of the PAW was also assessed against pathogenic microbes, with remarkable reductions in viability for both Staphylococcus aureus and Escherichia coli (99.99%) and a more moderate decrease for Candida albicans (37%). These findings underscore the capability of the coaxial DBD reactor in crafting high-quality PAW with significant antimicrobial properties, necessitating further studies to validate its broad-spectrum and safe application.

Cement paste backfill (CPB) is an effective waste management method allowing the storage of fine process tailings into underground mined-out voids. CPB performance generally depends on the sulfur content of the tailings and the type of binder. In recent years, there has been an in-creasing trend on the use of alkali-activated slag (AAS) to improve the performance properties of CPB. This study focuses on the ultrasonic and microstructural investigation of the effect of slag fineness on the mechanical, geochemical and durability properties of CPB made up of AAS (AAS-CPB) over 360 days. In this scope, AAS-CPB samples were prepared at three different fineness (3100-4650-6300 cm2/g). Fineness of slag significantly improved the early age- and long-term strength (~2.3 fold and ~6.6 fold, respectively) of CPB. However, further increase of slag fineness may have adverse effect on CPB microstructure and strength in the long term. Ultrasonic pulse velocity monitoring displayed very high relation with the strength evolution and durability assessment of CPB. Slag fineness at a degree was seen to improve the pore structure evolution of AAS-CPB. Microstructural studies are in good agreement with the geochemical and durability behavior of AAS-CPB. Microstructural and ultrasonic findings suggest that while slag fineness enhances the mechanical properties of AAS-CPB, further increase of the fineness of slag has no additional important technical advantages.

The Abnormal increase in the mass of adipose tissue during adipogenesis results in obesity. Obesity is a predominant disorder and its widespread has become a critical concern worldwide. This is due to the burden of its associated co-morbidities like cancer, cardiovascular diseases and diabetes. Over-nutrition and the sedentary lifestyle are considered as the most significant causes of abnormal adipose tissue development. Appropriate lifestyle and behavioural interventions are the corner stones of successful weight loss, but to maintain such a lifestyle is highly challenging. Accordingly, natural products from plants either as crude extracts or purified phytochemicals have shown to have anti-obesogenic properties and are generally non-toxic and cost-effective. In this review, we discuss the comparative analysis of molecular mechanisms involved in adipogenesis and the recently reported anti-obesogenic effects of various plant products. We will provide a common platform for understanding obesity and adipogenesis, and a possible mechanism of action for anti-obesogenic plant products through AMP-activated protein kinase (AMPK), which will support the scientific development of traditional herbal medicine.

Activated carbons can be produced from biomass in a thermal process either in a direct carbonization-activation process or by first carbonizing the biomass and later on activating the biochars into activated carbons. The properties of the ACs are dependent on the type of process used for production. In this study, the properties of activated carbons produced in a one-stage and a two-stage process are considered. Activated carbons were produced by physical activation of two types of starting materials, bio chars produced from spruce and birch chips in a commercial carbonization plant and from the corresponding raw chips. The activated carbons produced were characterized regarding specific surfaces, pore volumes and pore size distributions. The un-activated bio chars had some degree of surface area 190 and 140 m²g^-1 for spruce and birch and pore volumes of 0.067 and 0.092 cm³g^-1. According to the results obtained, two slightly different types of activated carbons are produced depending if a one-stage or a two-stage carbonization and activation process is used. The ACs produced in the one-stage process had higher specific surface areas compared to the ones produced in a two-stage process (761-940 m²g^-1 vs. 540-650 m²g^-1) . In addition, total pore volumes were higher in one-stage process but development of micropores is greater compared to two-stage process. There was no significant difference in total carbon content between one-stage and two-stage process.

Background: Methadone is a centrally-acting synthetic opioid analgesic widely used in the methadone maintenance therapy (MMT) programs throughout the world. Considering its neurotoxic effects particularly on the cerebellum, this study aims to address the behavioral and histological alterations in the cerebellar cortex associated with methadone administration. Materials and Methods: Twenty-four adult male albino rats were randomized into two groups of control and methadone treatment. Methadone was subcutaneously administered (2.5–10 mg/kg) once a day for two consecutive weeks. The functional and structural changes in the cerebellum were compared to the control group. Results: Our data revealed that treating rats with methadone not only induced cerebellar atrophy, but also prompted the actuation of microgliosis, astrogliosis, and apoptotic biomarkers. We further demonstrated that treating rats with methadone increased complexity of astrocyte processes and decreased complexity of microglia processes. Our result showed that methadone impaired motor coordination and locomotor performance and neuromuscular activity. Additionally, relative gene expression of TNF-α, caspase-3 and RIPK3 increased significantly due to methadone. Conclusions: Our findings suggest that methadone administration has a neurodegenerative effect on the cerebellar cortex via dysregulation of microgliosis, astrogliosis, apoptosis, and neuro-inflammation.

Plasma medicine is a new field focusing on biomedical and clinical applications of cold physical plasmas, including their anticancer effects. Cold plasmas can be applied directly or indirectly as plasma activated liquids (PAL). The effect of plasma activated cell growth medium (PAM) and plasma activated phosphate buffered saline (PAPBS) were tested using a plasma pen generating streamer corona discharge in ambient air, on different cancer cell lines (melanoma A375, glioblastoma LN229 and pancreatic cancer MiaPaCa-2) and normal cells (human dermal fibroblasts HDFa). The viability reduction and apoptosis induction were detected in all cancer cells after incubation in PAL. In melanoma cells we focused on detailed insights to the apoptotic pathways. The anticancer effects depend on the plasma treatment time or PAL concentration. The first 30 minutes of incubation in PAL were enough to start processes leading to the cell death. In fibroblasts, no apoptosis induction was observed, only PAPBS, activated for longer time, slightly decreased their viability. Anticancer effects of PAM and PAPBS on cancer cells showed selectivity compared to normal fibroblasts, depended on correctly chosen activation time and PAL concentration. This selectivity, supported by optimum ratio of hydrogen peroxide and nitrites in PAL, is very promising for potential clinical applications.

Lamin A, B and C, the nuclear intermediate-filament proteins, play a role in epigenetic regulation. While Lamin B is expressed in all nucleated cells studied, Lamin A/C are transcribed in most somatic cell types except mature B lymphocytes. Since Epstein-Barr virus (EBV), a human gammaherpesvirus, is associated with tumorigenic processes and is known to alter the epigenotype of its host cells, we studied the expression of the LMNA gene and its epigenetic marks in EBV-carrying human lymphoid cell lines. We observed a high lamin A/C mRNA and protein expression in EBV-immortalized lymphoblastoid cell lines (LCLs) and in group III Burkitt lymphoma (BL) lines where hypomethylated first exons were observed with activating histone marks. In most cell lines with low promoter activity a highly methylated first exon could be detected. Our data showed that methylation of the first exon of LMNA was associated with the downregulation of LMNA expression whereas euchromatic histone marks were enriched at active LMNA promoters in EBV-immortalized LCLs. These data suggest a role for viral latency products to activate LMNAp in EBV-infected latency type III B cells in vitro. Expression of lamin A/C may contribute to the establishment of activated B cell phenotype that needs further explorations.

The production of municipal solid waste incineration bottom ash (MSWIBA) is very massive and has the potential to replace cement despite the problems of complex composition, uneven particle size distribution, and low reactivity. This paper adopts sodium silicate activation of MSWIBA-slag to improve the reactivity to prepare composite cementitious materials. It explores the hydration performance study of the composite cementitious materials by isothermal calorimetric analysis, Fourier Transform Infrared (FTIR) spectroscopy, XRD physical diffraction analysis, and SEM/EDS tests. SEM/EDS tests will be used to explore the hydration properties of the composite gelling. The results showed that with the increase of MSWIBA doping, the porosity between the materials increased, the degree of Hydration decreased, and the compressive strength decreased with the rise of MSWIBA. When sodium silicate increased from 25% to 35%, too much alkaline material occurred over the alkaline effect, which inhibited the Hydration of the particles, and the degree of hydration reaction decreased, and the compressive strength decreased accordingly; the exothermic process of Hydration can be mainly divided into five stages, quartz and calcite did not participate in the hydration reaction completely, and sexual aluminum participated in the hydration reaction. The vibrational peaks of Si-O-Ti (T = Si and Al) were present in the material. The vibrational peaks of XRD, FTIR, and SEM-EDS all indicate the presence of silica-aluminate network structures in the hydration products, mainly N-A-S-H and C-A-S-H gels.

Choroid plexus insufficiency or glymphatic stasis are often classified as prequels to harmful accretion of toxic proteins in neurodegenerative disease. Cognitive decline and memory loss subsequently become cardinal features of Alzheimer’s disease (AD), typically progressing with amyloid-ß and tau protein accumulation. For Parkinson’s disease (PD), α-synuclein deposits and dopamine depletion are linked to impaired movement, resting tremor, and rigidity. Importantly, both diagnoses are accompanied by hyperinflammation and intrathecal cytokine changes. Thus far, numerous clinical trials for investigational drugs have produced nothing effective for AD or PD, yet the anti-inflammatory and regenerative potential of platelet-rich plasma (PRP) remains largely unexamined in this context. This report explores a proposed Phase I study on intrathecal condensed plasma growth factors processed from autologous thrombin-activated PRP as monotherapy for AD or PD. The concept gains support from related work where cytokines of platelet origin successfully lowered inflammation, corrected background fibrosis, deactivated abnormal cells, and recovered local tissue function—all desirable outcomes in AD and PD. PRP-mediated effects on membrane potentials, electrolyte balance, and water clearance are less well characterized, but experimental evidence suggests these pathways could likewise influence glymphatic drainage to ameliorate proteinopathies. As a well-tolerated ‘orthobiologic’ with no hypersensitivity risk, intrathecal PRP and its derivatives bring advantages distinct from synthetic pharmaceuticals. If age-associated neuroinflammation in AD and PD is an upstream event contributing to neural disruption, then dampening local oxidative stress by a patient’s own platelet cytokines (as already proven in other tissues) could offer therapeutic relevance to these neurodegenerative conditions as well.

Due to its high specific surface area and rich porous structure, acacia-derived porous activated carbon is the most potentially effective material for wastewater treatment. This research study aimed to prepare activated carbon using Acacia erioloba seedpods as carbonaceous materials and phosphoric acid as an activating agent. The specific surface area of the prepared activated carbon sample was characterised by Brunauer–Emmett–Teller instrument. The specific surface area value was 387 m²/g. The activated carbon prepared was then sieved into three different particle sizes of 50, 100 and 200 micrometres and characterised using various analytical procedures, including proximate analysis to study moisture content, ash content, volatile matter content and fixed carbon content. The bulk density, SEM, power of hydrogen, iodine number and methylene blue number index were also investigated to determine the adsorption properties of the prepared activated carbon. Batch adsorption dynamics for the removal of organic compounds such as methylene blue and unsaturated character of fatty acid from aqueous solution were also carried out at room temperature to evaluate the prepared activated carbon's applicability in water treatment. The iodine number was 528, 638, and 554 mg/g for the 50, 100, and 200 μm activated carbon particles, respectively. From the results, the adsorption of methylene blue favoured the Freundlich adsorption model, showing higher correlation (R²) values than the Langmuir model. The results indicate that methylene blue particles were adsorbed on heterogeneous surfaces.

Due to the accumulation of pesticides in the environment, the development of efficient strategies for their removal is of utmost importance. Activated carbons are currently seen as excellent candidates for adsorptive pesticide removal based on several beneficial properties, like a large surface area, developed porosity, and low price. However, a deep link between materials' properties and performance is still elusive. Here we focus on the kinetics of three organophosphate pesticides removal, aliphatic dimethoate and malathion and aromatic chlorpyrifos, using a series of carefully prepared activated carbon fibers. Used adsorbents have a wide range of specific surface areas, pore size distributions, and elemental content, allowing the establishment of the link between physicochemical properties and their performance as adsorbents. We use data analysis tools to link these properties and discuss their different roles in the removal of three structurally different yet extremely dangerous pesticides. The obtained results can guide the synthesis of novel adsorbents or rationally select adsorbents for specific target pollutants based on the physicochemical properties of adsorbents and the chemical structure of pollutants.