Organic electrophoretic coatings have gained significant attention due to their ability to provide a uniform and controlled coating thickness, high coating adhesion, and excellent corrosion protection properties. In this work, to investigate the aging behaviors of an organic electrophoretic coating for magnesium alloys, water absorption kinetics curves of the coatings after immersion in 3.5 wt.% NaCl at 20℃ and 40℃ were measured, and parameters such as the saturated water absorption and saturation time of the free film coatings were fitted to determine the densification evolution of the organic coatings. A tensile test was used to test the tensile strength of the organic coating during service to determine the evolution of the strength and toughness of the organic coating. The evolution of wet adhesion of organic coatings with service time was tested by ASTM D4541-02. The impedance spectra of the organic coatings under the above conditions were detected by EIS, and finally, the failure behavior of the organic coatings under immersion was analyzed.

Renal replacement therapy (RRT), widely used in the treatment of renal injury in the course of sepsis, aims to eliminate the toxins and proinflammatory cytokines, involved in the pathomechanism underlying septic shock. Dialysis filters characterised by a high adsorption potential for cytokines in RRT when septic renal injury is the case. It is of key importance in the antibiotics treatment of sepsis to achieve desired values of PK/PD indices. Continuous renal replacement therapy (CRRT) may affect antimicrobial clearance, increasing their elimination in some cases. The aim of this study was to determine the degree of adsorption for linezolid, on three different types of filters used in CRRT. In our in vitro study a continuous veno-venous hemofiltration (CVVH) was conducted using 3 types of filters: polysulfone (PS), polyethyleneimine-treated polyacrylonitrile (PAN PEI) and non-PEI-treated polyacrylonitrile (PAN) filters. Each type of filter was used in 3 CVVH cycles, involving the use of 600 mg of linezolid dissolved in 700 ml of bovine blood or in 700 ml of 0.9% NaCl. In each case the total volume of the obtained solution was 1000 ml. Blood samples, at particular time points, were collected in order to measure drug concentration. The differences in mean drug/NaCl adsorption and drug/ blood adsorption were determined using one-way ANOVA with multiple comparisons by Tukey post-hoc test. A p-value of < 0.05 was considered to be significant. A significant adsorption of linezolid was found for PAN PEI filter, both in samples obtained from bovine blood and 0.9% NaCl solutions, at the endpoint. No significant adsorption was demonstrated on PAN or PS filters. There is a need for in vivo research to confirm the effect of filter type on linezolid concentration in patients undergoing CRRT.

(1) Background: Food waste (FW) in Romania is 70 Kg/capita/year, while 70% of food waste comes from public catering, retail services, and households (over 50% – 47 million tons). (2) Methods: A cross-sectional observational study was conducted using an online questionnaire via the Google Forms platform from 15 April 2023 to 15 May 2023. The questionnaire was designed to assess various aspects, such as some socio-demographic information (age, sex, occupation, area of residence, study level, household members number, children &lt; 18 years of age); the personal involvement and frequency of food purchases and homemade food cooking; the main sources that generate food waste; the motivation and frequency with which food waste occurs; the level of awareness regarding the impact of food waste; the respondents' intentions regarding sustainable behaviors and practices food management; the level of information and familiarity of the respondents with the notions of validity and how these may influence their food consumption decisions. (3) The results show that FW incidence is occasionally (42%), very rarely (43.33%), frequently (15%), and no food waste was reported by 2.66% of respondents. The [35-44] age category records the highest FW frequency, followed by [18-24]. The most wasted are homemade food (29.67%), bread and bakery products (27.00%), and fruits and vegetables (14.33%). High involvement in purchasing and buying food following a previously established list reduces FW frequency. The same is valid for high daily involvement in food and homemade cooking. High interest in the FW problem and its perception as a waste of money leads to diminishing it, while guilty feelings increase the FW level (37.50% to 73.33%). (4) Conclusions: The present study shows that household food waste management is a multifactorial process that involves numerous socio-demographic, behavioral, and emotional aspects. Extensive data analysis supports our results, revealing deep self-reported information details and confirming its complex approach.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

Promoting organic foods production and consumption contributes to accomplishing United Nations sustainable development goals. Social commerce provides a promising opportunity to develop the organic food industry. However, there is limited knowledge regarding customer behaviors in relation to purchasing organic foods via social commerce platforms. Therefore, this study expanded upon the unified theory of acceptance and use of technology (UTAUT-2) to develop a comprehensive model that explains how customers' social commerce trust and behavioral intentions to purchase organic foods using Instagram social commerce affect their purchasing behaviors. The research model was analyzed by employing partial least squares structural equation modeling (PLS-SEM) for the data collected from a quantitative survey of 410 customers who used Instagram to purchase organic foods in Iran. The results revealed that facilitated purchasing conditions, hedonic motivations, social influence, rating and reviews, and influencers’ endorsements increase customers' purchase intentions. Moreover, Instagram’s recommendations and referrals, influencers’ endorsements, as well as social influence boost customers' trust in the social commerce platform. Eventually, it was determined that influencers’ endorsements, social commerce trust, and purchase intention determine a customer’s organic foods purchasing behaviors. This research provides valuable insights for organic food marketers to optimize their social commerce strategies.

According to Hofstede’s theory of cultural dimensions, cultures differ in cultural values and norms; values and norms that may influence differences in trendsetting, creative traits and behaviors, and pro-environmental behaviors. Further, because men and women have been socialized within particular cultures, gender differences may exist in trendsetting, creative traits and behaviors, and pro-environmental behaviors. Trendsetters have characteristics that are interrelated with creative traits and behaviors, perhaps inclining them to endorse pro-environmental behaviors. However, the interrelationships among these variables remain unexplored. Thus, the purpose of this study was to examine these three variables among college students in South Korea and the United States, specifically looking at cultural and gender differences. Participants were 225 Korean college students and 221 U.S. college students. Questionnaires included demographic items and scales measuring trendsetting, creative traits and behaviors, and pro-environmental behaviors. Data analyses included descriptive statistics, Cronbach’s alpha reliability, MANOVA, ANOVA and SNK posthoc test. Results show that U.S. (vs Korean) students indicated greater trendsetting and creative traits and behaviors but not greater pro-environmental behaviors. Fashion trendsetting groups in both Korea and the U.S. differed in creative traits and behaviors and pro-environmental behaviors. Among Korean trendsetting groups, reluctant adopters scored lowest on creative traits and behaviors and pro-environmental behaviors. Among U.S. trendsetting groups, trendsetters scored highest on creative traits and behaviors and pro-environmental behaviors; reluctant adopters scored lowest on pro-environmental behaviors. Theoretical and practical implications are provided for researchers and marketers.

In this study, a cholera infection model with the bilinear infection rate is developed by considering the perturbation of the infection rate by the mean-reverting process. First of all, we give the existence of a globally unique positive solution for a stochastic system at arbitrary initial value. On this basis, the sufficient condition for the model to have an ergodic stationary distribution is given by constructing proper Lyapunov functions and tight sets. This indicates in a biological sense the long-term persistence of cholera infection. Furthermore, after transforming the stochastic model to an relevant linearised system, an accurate expression for the probability density function of the stochastic model around a quasi-endemic equilibrium is derived. Subsequently, the sufficient condition to make the disease extinct is also derived. Eventually, the theoretical findings are shown by numerical simulations. Numerical simulations show that the impact of regression speed and fluctuation intensity on stochastic systems.

: The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDX, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.78; 2.24 and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDS, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a breakthrough adsorption experimental setup at room temperature. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.47; and 1.20 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

Coaches are the main people who have an impact on the mental and psychological performance of athletes as well as their physical performance. The purpose of this study is to investigate the effect of perceived coaching behaviors on the anger and aggression levels of male athletes. This study was conducted with 748 male athletes with an active license who are over 18 years of age and participate in individual and team sports branches. In this study, the "Coaching Behavior Assessment Ques-tionnaire" and the “Competitive Aggressiveness and Anger Scale" were used as data collection tools. The study results showed that athletes’ levels of evaluation of the coaching behaviors were high, while the levels of aggressiveness and anger in sports were low. It was determined that there is a negative low-level relationship between the athletes’ evaluation levels of the coaching be-haviors and the aggressiveness and anger levels in sports and that the coach’s behaviors predict the anger and aggressiveness levels of the athletes by 9% and 6%, respectively. The results of this study show that the attitudes and behaviors of coaches can affect the emotional states of male athletes and have the potential to increase or decrease their anger and aggressiveness levels. Coaches who exhibit positive, supportive, and modeling behaviors help create a healthy sports environment and help male athletes maintain emotional balance.

A sustainable low cost activated carbon substitute was produced based on pretreated lignocellulosic biomass, especially spruce sawdust. A harmful liquid waste, desalination brine was used for the treatment of a solid wood industry waste, spruce sawdust. This approach is in the circular economy theory and aims to the decarbonization of the economy. The pretreated sawdust was tested as an adsorbent appropriate for the removal of a commonly used pollutant, methylene blue, from industrial wastewater. The adsorption capacity of the pretreated material was found to increased four times comparing to the untreated one in the case that the Freundlich equation was fitted to the isotherms’ data. The treatment experimental conditions with desalination brine that gave maximum adsorption capacity correspond to 1.97 combined severity factor in logarithmic form value. The same adsorption capacity was found to increase five to six times comparing to the untreated spruce sawdust in the case that the Langmuir isotherm model was applied at the same data. Moreover, kinetic experiment was cried out as regards the methylene blue adsorption process. The desalination brine pretreated sawdust adsorption capacity increased 1.4 times comparing to the untreated one, in the case of the Lagergren kinetic equation fitting. Furthermore, the adsorption capacity of the same material was increased 1.6 times when the second order kinetic model was applied to the same data. Industrial scale applications can be based on the kinetic data findings as they have to do with a very shorter adsorption period comparing to the isotherm data.

In order to study the adsorption process and adsorption characteristics of shale oil at the macro scale, the isothermal adsorption experiments of illite and kerogen on heptadecane (oil phase) solution were carried out by infrared spectrophotometry and gas chromatography-mass spectrometry. The reaction mechanism of alkane solution concentration and temperature in the adsorption process was investigated. The adsorption characteristics of heptadecane on the surface and pores of illite and kerogen were elucidated by adsorption isotherm model and adsorption thermodynamic model. The results show that: The concentration of alkane solution contributes to the adsorption of illite and kerogen. As the concentration of the solution continues to increase, the adsorption rate gradually slows down. However, the temperature hardly affects the adsorption rate. At 25℃, 50℃ and 60℃, the adsorption process of illite on alkane solution is more consistent with Langmuir model and Freundlich model, respectively. The difference is that Langmuir model is suitable for describing the whole adsorption process of kerogen on alkane solution. 3) The adsorption process of illite and kerogen to heptadecane solution is an endothermic reaction. Heating helps to accelerate the migration rate of alkanes, which is conducive to the adsorption reaction. The research results clarify the adsorption characteristics of shale oil heavy components from the macro level, and fill the research gap in the application of solid-liquid isothermal adsorption physical experiments to the adsorption and occurrence of shale oil.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

This work aimed to develop an anionic cellulose nanofiber (CNF) bio-adsorbent from palm date tree waste and to investigate its removal efficiency against cationic methylene blue dye from contaminated water. Palm date pulp was first prepared from palm date leaves through acid hydrolysis using H2SO4, followed by hydrolysis in a basic medium using KOH, in which the process completely removed the components of hemicellulose, lignin, and silica. To obtain anionic CNF, the resulting pulp was further treated with H2SO4, followed by centrifugation. Biogel formation of the CNF suspension was promoted by sonication, where its removal efficiency of methylene blue dye was studied as a function of dye concentration, temperature, contact time, and pH value. Two equilibrium models, the Langmuir and Freundlich models were employed, and the Langmuir model was found to be consistent with the experimental data. The highest removal efficiency was obtained at 60oC and was 5mg/gm. Furthermore, several kinetic models were used to gain insight into the adsorption mechanism. The pseudo-second-order model provided an accurate description of the adsorption process, while the Elovich equation suggested a chemical reaction between methylene blue dye and CNF. The study’s findings were in agreement with the pseudo-second-order model, indicating general chemical reactions. The study indicates that CNF adsorbents derived from renewable natural waste sources such as palm date leaves can be effective in removing cationic contaminants such as methylene blue dye.

Based on research data from the renovation of old residential areas in Chengdu, China, this study provides empirical evidence regarding the causal relationship between urban renewal and the transformation of residents' pro-environmental behaviors. The research findings demonstrate a significant enhancement in residents' engagement in pro-environmental behaviors due to the renovation of old residential areas. Robustness tests based on replacement samples and two-stage difference-in-difference models also confirm the reliability of the conclusions. The preliminary mechanism test indicates that the mechanism of the impact of renovation of old residential areas on the transformation of residents' pro-environmental behaviors can be attributed to two main factors. Firstly, the improvement of environmental infrastructure provides residents with better conditions for participating in pro-environmental activities. Secondly, there is an elevation in residents' environmental protection awareness, prompting a more voluntary engagement in pro-environmental behavior. This study suggests that decision-makers should fully recognize that urban renewal activities nationwide are not only a process of improving urban hardware and functionality, but also a realistic and vivid "environmental education" course for the whole nation. Taking urban renewal as an opportunity to enhance citizens' awareness of environmental protection will effectively promote the transformation of pro-environmental behaviors among residents.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

PFAS are a variety of ecologically persistent compounds of anthropogenic origin loosely included in many industrial products, in which the carbon chain can be fully (perfluoroalkyl substances) or partially (polyfluoroalkyl substances) fluorinated. Their ubiquitous presence in many environmental compartments over the years, and highly long-lasting nature, arose concern because of the possible adverse effects of PFAS on ecosystem and human health. Between the remediation technologies, adsorption has been demonstrated to be a maneageble and cost-effective method for the removal of PFAS in aqueous media. This study tested two novel and eco-friendly adsorbents (pinewood and date seeds biochar) on 6 different PFAS (PFOS, GenX, PFHxA, PFOA, PFDA, PFTeDA). Batch sorption tests (24 hours) were carried out to evaluate the removal efficiency of each PFAS substance in relation to the two biochars. All samples of liquid phase were analysed by a developed and then well-established method: i) pre-treatment (centrifugation and filtration); ii) determination by high-performance liquid chromatography coupled with mass spectrometry (HPLC-MS/MS). Results evidenced a comparable adsorption capacity of both materials, but greater for the long-chain PFAS. Such findings may lead to a promising path for the use of waste origin materials in the PFAS remediation field.

The results of the investigation showed that second-order kinetics govern the adsorption process, and the corresponding rate constants were found. To evaluate the parameters related to the adsorption process, the adsorption equilibrium was examined using a variety of mathematical models, such as the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models. The Langmuir isotherm was found to be the best appropriate among all models for describing the adsorption of Cu2+ and Ni2+ ions using bio-nanocomposite beads. The positive values of ΔH° indicate that the adsorption is physical and endothermic, in agreement with experimental results. The negative value of ∆G° shows that the adsorption process is spontaneous. Positive ΔS° values indicate increased randomness at the solid/liquid interface, during adsorption of Cu2+ and Ni2+ cations onto the engineered bio-nanocomposite. The maximum adsorbed amounts of metal ions by the bio-nanocomposite used were 370.37 mg/g for Ni2+ and 454.54 mg/g for Cu2+ from single system. For the binary system, according to the Langmuir isotherm, the maximum adsorbed amounts of Ni2+ and Cu2+ were 357.14 mg/g and 370,37 mg/g, respectively. There is proof that Alginate-Moroccan clay bio-nanocomposites can serve as a different, less expensive source of sorbents for the removal of metal ions from single and binary systems.

In this paper, quasi-static axial compression tests are performed on the nodal Moso bamboos to study the size effect on energy absorption of the bamboos and the damage pattern of the multiple bamboo columns. Experimental results show that under the same moisture content, growth age and growing environment, the specific energy absorption (SEA) of the test samples increases with the increase of the out-diameter and thickness of the bamboo columns, indicating that size effect exists for energy absorption of the Moso Bamboos. For the multiple bamboo columns, there are mainly three failure modes for the constituent single bamboo columns: splitting above the node, splitting below the node and splitting through the node. Also, the tensile tests are conducted on three kinds of dog-bone shaped bamboo samples to investigate the macroscopic tensile fracture mode in the longitudinal direction of Moso bamboos. Results show that there is no direct relationship between the fracture pattern and moisture content of the bamboos, as well as the growth age of the bamboos. However, the tensile loading rate and the shape of the dog-bone shaped bamboo sample could affect the macroscopic fracture pattern of the bamboos in some cases.

Even in the first quarter of XXI century, the presence of organic dyes in wastewaters is a normal occurrence in a series of countries, and being these compounds toxics, their removal from these waters is of a necessity. Among the separation technologies, adsorption processing appeared as one of the most widely used to reach this goal. The present work reviewed the most recent approaches (first half of 2021 year) about the use of a variety of adsorbents on the removal of, also, a variety of organic dyes of different nature.

Metal-reinforced polymethyl-methacrylate (PMMA) is considered the gold standard material for immediate loading on dental implants. However, mechanical problems under loading cycles can occur, such as fractures. To overcome these drawbacks, a novel polymer-based material has been proposed. The aim of the present in vitro comparative research is to validate a novel composite polymer developed to replace metal-reinforced PMMA interim restoration due to its advantages of good mechanical proprieties, easier manufacturing, and handling. Ten interim restorations were CAD/CAM designed and fabricated (five in the composite "ONLY" group, and five in the metal-reinforced PMMA group). All the samples were screwed into the prototype models, simulating a complete edentulous mandible rehabilitated with six straight implants. Outcome measures were breakpoint (load, N) and displacement (mm) thought a static, compression test and material behavior under dynamic cyclic test method (fatigue test). A total of twenty samples were tested. Ten samples were used for each test (10 for static and 10 for dynamic), five samples were used in each group (test and control). All the specimens completed the mechanical tests, as planned. There was no statistically significant difference between groups for all, breakpoint, displacement and fatigue tests. Breakpoint in the test group was 1953.19 ± 543.73 N, while, it was 2031.10 ± 716.68 N in the control group, with no statistically significant difference (P=0.775). The displacement was 1.89 ± 0.34 mm in the test group and 1.98 ± 0.75 mm in the control group, again, with no statistically significant difference (P=0.763). Under dynamic cyclic test method, in the control group the mean load was 2504.6 ± 972.15 N, while, in the test group the mean load was 3382 ± 578.5 N. The difference between group was 877.4 ± 579.3 N (p value=0.121). With the limitation of this in vitro study, the novel composite polymer can be used to immediately load dental implants. Further clinical researches are needed to confirm this preliminary results.

Cloth wearing seems so natural that everyone is self-deemed knowledgeable and has some expert opinions about it. However to clearly explain the physics involved, and hence to make predictions for clothing design or selection, turns out as demonstrated below to be quite challenging even for experts. Cloth is a multiphased, porous and anisotropic material system and usually in multilayers. Unlike ordinary engineering heat transfer problems, the human body acts as an internal heat source in a clothing situation, thus forming a temperature gradient between body and ambient, and the sign of this gradient often changes as the ambient temperature varies. Our body also perspires and the sweat evaporates, an effective body cooling process via phase change. To bring all the variables into analysis quickly escalates into a formidable task. This work attempts to unravel the problem from a physics perspective, focusing on several rarely noticed yet critically important mechanisms involved so as to offer a clear and accurate depiction of the principles in clothing thermal comfort.

As the interface between human and machine becomes blurred, hydrogel incorporated electronics and devices have emerged to be a new class of flexible/stretchable electronic and ionic devices due to their extraordinary properties, such as soft, mechanically robust and biocompatible. However, heat dissipation in these devices could be a critical issue and remains unexplored. Here, we report the experimental measurements and equilibrium molecular dynamics simulations of thermal conduction in polyacrylamide (PAAm) hydrogels. The thermal conductivity of PAAm hydrogels can be modulated by both the crosslinking density and water content in hydrogels. The crosslinking density dependent thermal conductivity in hydrogels varies from 0.33 to 0.51 Wm^-1K^-1, giving a 54% enhancement. We attribute the crosslinking effect to the competition between the increased conduction pathways and the enhanced phonon scattering effect. Moreover，water content can act as filler in polymers which lead to nearly 40% enhancement in thermal conductivity in PAAm hydrogels with water content vary from 23 to 88 wt%. Furthermore，we find the thermal conductivity of PAAm hydrogel is insensitive to temperature in the range of 25 ^oC – 40 ^oC. Our study offers fundamental understanding of thermal transport in soft materials and provides design guidance for hydrogel-based devices.

This study aims to explain individual engagement in sustainable waste management behaviors (SWMBs) based on the application of protection motivation theory (PMT). SWMBs include waste avoidance, green purchasing behavior, reuse and recycle, and waste disposal behaviors. This study applies PMT to explore how individuals’ SWMBs are influenced by their perceived threats caused by environmental contamination from waste disposal and their perceived coping capability. The Bangkok metropolitan area was selected as a case study because it has faced serious waste management problems caused by massively increasing amounts of solid waste during the last ten years. Questionnaire surveys were conducted with 193 public and private officers residing in the city of Bangkok. The one-way analysis of variance (ANOVA) was performed to justify the effect of individual threat appraisal and coping appraisal on the engagement in SWMBs. The results demonstrated that respondents’ self-efficacy highly influenced all types of SWMBs. The perceived probability of being impacted from pollutants influenced all of the SWMBs except green purchasing behaviors. Response efficacy did not influence all SWMBs; however, the perceived severity of adverse consequences caused by pollutants highly influenced reuse and recycle behaviors. It could be suggested that PMT is well suited for investigating low-cost and simple SWMBs. It could also be suggested that different communication campaigns should be established to enhance citizens’ engagement in each type of SWMB.

Nutritional status problems in school-age children are a crucial public health problem worldwide. This research explored the relationships between family factors, food consumption behaviors, and the nutritional status of Muslim school-age children in Thasala District, Nakhon Si Thammarat Province, Thailand. This descriptive research was conducted among 228 children aged 9-12 years. Data were collected using demographic data, nutritional status, and food consumption behaviors assessment. Data were analyzed using descriptive, chi-square, and binary logistic regression statistics. The results revealed that most samples reported having moderately healthy food consumption behaviors (M = 2.01, SD = 0.56). The samples had a normal weight (72.4%), while 15.8% were classified as overweight and obese. The number of siblings and food consumption behaviors had a significant relationship with nutritional status (p &lt; 0.05). Confirmation with binary logistic regression results also revealed that the likelihood of normal nutritional status was 2.40 times higher in children who had 3 or 4 siblings compared to those with 1 or 2 siblings (AOR = 2.40; 95% CI: 1.299-4.459). Additionally, children with healthy food consumption behaviors were 2.34 times more likely to have normal nutritional status compared to those with unhealthy dietary consumption (AOR = 2.34; 95% CI: 1.183-4.631). Conclusion: Since the number of siblings and healthy food consumption behaviors were associated with nutritional status, healthcare providers must consider these 2 factors when establishing health education and behavior modification care plans to promote healthy food consumption and nutritional status among this group.

Silicon (Si) is the major material of semiconductor element. For semiconductor element producing, Si need to refined into high-purity silicon crystals, which has the approximate characteristics of intrinsic semiconductor, then doping 13th group or 15th group trace element. Producing the high-purity silicon crystals with well-lattice structure need a lot of energy and highly cost. Besides, the high-purity silicon is very hard and fragile which limits the scope of application. For this reason, this study added low-grade non-complete lattice silicon in the elastic polymer, and then doped with high concentrations of fine carbon powder. This material can be conductive by physisorption;therefore, it can be used to making semiconductors. Using this material to produce electronic components can significantly reduce the cost of purification and crystallization, saving energy at the same time. Moreover, because this elastic polymer materials containing silicon, which has soft, warm, and durable physical properties. With those properties, the design of the device could be more flex, full scalability and close to the skin.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

With the continuous advancement of digital transformation, digital payments are playing an increasingly important role in the financial industry. This study aims to utilize machine learning models to predict and analyze digital payment behavior. Initially, the background and significance of digital payments in the financial sector are introduced. Subsequently, the current status and trends of traditional digital payment distribution are reviewed, alongside related work on digital payment behavior prediction. Methodologically, principles and applications of machine learning models such as logistic regression, decision trees, and random forests are elaborated, along with experimental design and data preprocessing methods. The experimental results and discussion section illustrates the performance of each model in digital payment prediction and explores their impact on credit decisions. This exploration equips financial institutions with more effective user behavior analysis and risk management tools, thereby fostering future development and application of digital payment technologies.

With the continuous advancement of digital transformation, digital payments are playing an increasingly important role in the financial industry. This study aims to utilize machine learning models to predict and analyze digital payment behavior. Initially, the background and significance of digital payments in the financial sector are introduced. Subsequently, the current status and trends of traditional digital payment distribution are reviewed, alongside related work on digital payment behavior prediction. Methodologically, principles and applications of machine learning models such as logistic regression, decision trees, and random forests are elaborated, along with experimental design and data preprocessing methods. The experimental results and discussion section illustrates the performance of each model in digital payment prediction and explores their impact on credit decisions. This exploration equips financial institutions with more effective user behavior analysis and risk management tools, thereby fostering future development and application of digital payment technologies.

Based on the 2014-2015 China Education Panel Survey (CEPS) and using the propensity score matching method, we studied the causal relationship between physical exercise and prosocial behavior of junior middle school students in China. Ordinary least squares regression and propensity score matching estimation results showed that participation in physical exercise significantly increases students’ prosocial behavior by more than 0.2 standard points. The results of this study were tested and found to be robust.

The safety of a pedestrian crossing may depend on infrastructure, vehicular and pedestrian traffic characteristics. This research portrays the safety challenges caused by vehicles on crosswalk in the City of Kigali. Through observing the stopping of drivers in pedestrian crossing events, the study aims to evaluate driver’s behaviors against traffic flow parameters. 10 collection sites were finally selected purposively and randomly to suit observations for data recording. A total of 10,259 crossing events were recorded within 280 hours. Statistical analysis, tests and Binary logistic regression model were used to evaluate the behaviors. Sadly,82.4% drivers violate crosswalks, endangering crossing. Motorcyclists exhibit the most aggressive behavior. Car drivers are relatively less aggressive,60% managed to brake in the events. Buses and bicycles share a negligible collective of 2%, being aggressive and would not stop. Cars are 10.389 times more likely to stop compared to bicycles. Having more vehicles in a row is safer to cross, for each unit increase on the vehicle density scale, there were 1.956 more chances that every driver would stop.13% to 21% of traffic variables predict the variance in stopping behaviors model.

Layered Ti3C2Tx MXene has been successfully intercalated and exfoliated with the simultaneous generation of a 3D silica network by treating its cationic surfactant intercalation compound (MXene-CTAB) with an alkoxysilane (TMOS) resulting in a MXene-silica nanoarchitecture that exhibits porosity along with the intrinsic properties of MXene (e.g., photothermal response). The ability of these new materials to produce thermal activation reactions of compounds previously adsorbed on MXene-SiO2 is shown here. For this purpose, the pinacol rearrangement reaction has been selected as a first model example, testing the effectiveness of NIR laser-assisted photothermal irradiation in these processes. This work shows that Ti3C2Tx – based nanoarchitectures open new avenues for applications that rely on the combined properties inherent to their integrated nanocomponents that could be extended to the broader MXene family.

Carbamazepine (CBZ) is one of the most common emerging contaminants released to the aquatic environment through domestic and pharmaceutical wastewater. Due to its high persistence through conventional degradation treatments, is considered a typical indicator for anthropogenic activities. This study tested the removal of CBZ through two different clay-based purification techniques: adsorption of relatively large concentrations (20-500 μmol L-1) and photocatalysis of lower concentrations (&lt;20 μmol L-1). The sorption mechanism was examined by FTIR measurements, exchangeable cations released, and colloidal charge of the adsorbing clay materials. Photocatalysis was performed in batch experiments under various conditions. Despite the neutral charge of carbamazepine, the highest adsorption was observed on negatively charged montmorillonite-based clays. Desorption tests indicate that adsorbed CBZ is not released by washing. The adsorption/desorption processes were confirmed by ATR-FTIR analysis of the clay-CBZ particles. A combination of synthetic montmorillonite or hectorite with low H2O2 concentrations under UVC irradiation exhibits efficient homo-heterogeneous photodegradation at μM CBZ levels. The two techniques presented in this study suggest solutions for both industrial and municipal wastewater, possibly enabling water reuse.

The high environmental impact of conventional methods of cooling and heating has increased the need for renewable energy deployment for covering thermal loads. Towards that direction, the proposed system aims at offering an efficient solar powered alternative, coupling a zeolite-water adsorption chiller with a conventional vapor compression cycle. The system is designed to operate under intermittent heat supply of low-temperature solar thermal energy (<90 °C) provided by evacuated tube collectors. A prototype was developed and tested in cooling mode operation. The results of separate components testing showed that the adsorption chiller was operating efficiently, achieving a maximum coefficient of performance (COP) of 0.65. With respect to the combined performance of the system, evaluated on a typical week of summer in Athens, the maximum reported COP was approximately 0.575, mainly due to the lower driving temperatures at a range of 75 °C. The corresponding mean energy efficiency ratio (EER) obtained was 5.8.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

The temperature effect plays an important role for an accurate determination of the polar free energy, polar thermodynamic parameters, and enthalpic and entropic Lewis’s acid base properties of oxides, polymers and composites polymers/oxides. The adsorption of polymers on other solid surfaces is crucial in many industrial applications, coatings, paints, catalysis, colloids and adhesion processes. (1) Background: Inverse gas chromatography at infinite was used for the physico-chemical characterization of solid substrates by determining the thermodynamic parameters of adsorption of model organic solvents on solid surfaces such as polymers, metallic oxides, carbon fibers, pharmaceutical or 3D/4D printing substrates. (2) Methods: A new method based on the London dispersion equation was applied with a new parameter associating the deformation po-larizability and the harmonic mean of the ionization energies of solvent. More accurate values of the dispersive and polar interaction energies of the various organic solvents adsorbed on PMMA in bulk phase and PMMA/silica at different recovery fractions were obtained as well as the Lewis acid-base parameters and the transition temperatures of the different composites. (3) Results: This new methodology gave very interesting results on the behavior of PMMA adsorbed on silica. An important effect of the temperature and the recovery fraction on the various physicochemical and thermodynamic properties was highlighted. The variations of all interaction parameters showed the presence of three transition temperatures for the different PMMA adsorbed on silica with the various coverage rates with a shift of these temperatures for a recovery fraction of 31% (4) Con-clusions: An important variation of the polar enthalpy and entropy of adsorption, the Lewis ac-id-base parameters and the intermolecular separation distance as a function of the temperature and the recovery fraction of PMMA on silica.

Evaluating the economic and environmental effects of farmers' green production behaviors holds important reference value for promoting sustainable agricultural development, alleviating agricultural non-point source (NPS) pollution, and achieving the organic combination of environmental protection and economic development. This paper utilizes survey data from 1,345 farm households in the main rice production areas of Jiangxi Province, China, using the example of reduced fertilizer application (RFA) among rice farmers. By constructing a DEA—SBM model with undesirable outputs to measure environmental effects, and applying an endogenous switching model to test the economic and environmental effects of farmers' adoption of green production technologies. The study found that: (1)The behavior of RFA by farmers has a significant positive impact on their net profit per mu(NPPA), helping farmers increase their income, with the increase ranging from 2.05% to 6.54%. (2)The behavior of RFA by farmers has a significant positive impact on agricultural green productivity(AGP), contributing to the improvement of the environment, with the improvement ranging from 44.09% to 45.35%. (3)Heterogeneity analysis found inconsistencies in the income-enhancing and environmental-enhancing effects at different quantiles of NPPA and AGP. Therefore, attention should be placed on improving the agricultural product quality supervision system under the market circulation mechanism, creating land scale conditions conducive to the promotion and application of fertilizer reduction technologies, and promoting the implementation of externality internalization compensation systems.

Domestic violence (DV) has been reported high in minorities across the US. Among minorities, refugees and immigrants encounter several barriers that may influence their responses and actions regarding DV. This scoping review examined three decades of literature (1980-2022) on resettled Afghan and Arab refugee women's attitudes and behaviors toward DV in their host countries, and to summarize research, practice, and policy recommendations. Based on Arksey and O'Malley model, our scoping review conducted extensive searches in SCOPUS, PubMed, PsychInfo, CINAHL, Web of Science, the Directory of Open Access Journals, and Embase databases. Searches identified articles that examined resettled Afghan and/or Arab refugees’ responses to DV in Western countries. The search identified 439 unique citations; 17 met the inclusion/exclusion criteria. Major themes included acculturative changes in refugee attitudes and behaviors and in stakeholders’ perspectives and roles. Significant acculturative attitudinal changes (acknowledgment, silence, justification, or disapproval of DV) contrasted with minimal behavioral changes (help-seeking behaviors, action plans, or barriers to actions) and with a resistance to change in stakeholders (cultural norms and beliefs, community patriarchal normalization of violence, service providers unfamiliarity with client diversity and refugee cultures) in supporting women decision-making regarding DV. Not a single article made explicit policy recommendations.

As novel materials for carbon capture, phase change solvents can separate into two immiscible phases during the CO2 capturing procedure under a certain temperature. The solvent systems can significantly decrease the energy consumption since the solvents can be regenerated by only heating the rich-CO2 phase. In this work, amino acid ionic liquids (AAILs) were synthesized using quaternary ammonium salts and amino acids as raw materials, and the aqueous solutions were prepared as novel liquid-solid phase change solvents. The results showed that the solvents had excellent CO2 absorption capacity, and the AAILs functionalized by glycine and tryptophan exhibited significant phase change properties. The mechanism of phase-change of the solvent were mainly due to the lower solubility of the product after reaction between AAILs and CO2. The solvent with tryptophan as anion could be regenerated by only heating the CO2-riched solid phase, which might significantly decrease energy consumption of regeneration. And the absorbent could be reused with the regenerated absorption ratio up to 79%. The solvent system has great potential in industrial application due to the easy operation process and efficient recycling ability.

Background Eating disorders are complex illnesses with serious long-term consequences. They are linked to negative outcomes such as miscarriage, low birth weight, and other obstetric and postpartum difficulties. Our study in Muscat, Oman, examines the eating habits of pregnant women who consult primary care physicians. We aim to understand how eating disorders affect pregnant women and inform more effective interventions. Method We used the Eating Disorder Examination Questionnaire to assess the potential for the presence of eating disorders. Chi-Square and Fisher's Exact tests were used to analyze relationships between improper eating behavior and independent variables. Results The study showed that 1.6% of participants had a potential diagnosis of an eating disorder, with the most common inappropriate behavior being binge-eating at a prevalence of 18.8%. A pre- gestational low Body Mass Index (BMI) was associated with a higher prevalence of binge eating during pregnancy. Additionally, we found that pregnant women who were working were more prone to self-induced vomiting. High BMI before pregnancy was significantly associated with various inappropriate eating behaviors such as restraint behavior (p = 0.000), shape concern (p = 0.000), weight concern (p = 0.040), eating (p = 0.045), laxative use (p = 0.020), and excessive exercise (p = 0.043). Conclusion The study reveals a high prevalence of eating disorders in pregnancy. Less educated women exhibit higher laxative use, while working women show more instances of binge eating and self-induced vomiting. These findings emphasize the critical need to prioritize targeted interventions and support for vulnerable pregnant women.

Large-scale volumetric fracturing is generally used during shale gas development. The return rate of fracturing fluid is low, and a large amount of slickwater will be retained in the reservoir. The adsorption and desorption of partially hydrolyzed polyacrylamide (HPAM), an additive commonly used in slickwater, on the surface of shale was studied using Longmaxi Shale from the Sichuan Basin. The experimental results showed that the mass ratio of the HPAM solution to shale reached saturation adsorption at 20:1 when the concentration of HPAM solution was 1000 mg/L and 25:1 when the concentration of HPAM solution was 500 mg/L. The mass ratio of the HPAM solution to shale was fixed at 25:1, and the adsorption equilibrium was reached at a HPAM concentration of 1000 mg/L when the aqueous solution temperature was 30°C and 800 mg/L when the aqueous solution temperature was 60°C. The Langmuir adsorption model yielded a better fit than the Freundlich adsorption model. The adsorption equilibrium time at 30°C was at 60 min for a HPAM concentration of 500 mg/L, while for a concentration of 1000 mg/L, it was at 90 min. The adsorption equilibrium time at 60°C was 40 min for a HPAM concentration of 500 mg/L, whereas it was 60 min for a HPAM concentration at 1000 mg/L. The pseudo-second order kinetics model yielded better fits than the pseudo-first order kinetics model. The adsorption of HPAM on shale was strong, and the adsorbed HPAM resembled cobwebs adhering to the shale surface. HPAM on the surface of shale after adsorption could resist the desorption capacity of water. However, when the amount of adsorbed HPAM on shale increased significantly, the amount of residual HPAM on the surface of the shale decreased rapidly during desorption in deionized water. The desorption of HPAM on the shale surface followed a modified desorption model. The higher the concentration of HPAM adsorbed on the shale surface was, the easier it was to desorb, the easier it was to be removed from the shale.

High levels of groundwater containing both arsenic and fluorine are prevalent, resulting in serious health problems when consumed as drinking water. This co-pollution phenomenon is widespread and requires urgent attention. The multiple forms of arsenic and arsenic-fluorine co-contamination pose a significant challenge to efficiently co-remove both substances. This research utilized a green and stable synthesis approach to create MgLaFe LDO heterostructures, which were anchored on α-MnO2 nanowires. The materials comprise magnesium and lanthanum elements with a powerful attraction towards fluoride ions, elemental iron, which can establish stable compounds with arsenate, and MnO2, which can effectively oxidize arsenous acid, thereby enabling efficient co-removal of arsenic and fluorine. The efficient oxidation process of the MnO2 nanowire and the prompt ion adsorption process of the LDO work together synergistically. The adsorption performance was assessed through isotherm and kinetic fitting. Chemisorption was found to be the process for As(Ⅲ), As(V), and F- adsorption, with As(Ⅲ) going through monolayer adsorption on the surface of MnO2 nanowires, while As(V) and F- were mainly adsorbed by multilayer process on LDO. The maximum adsorption capacities were 111.76 mg/g, 230.51 mg/g, and 765.10 mg/g for As(Ⅲ), As(V), and F-, respectively. The XPS analysis provided further elucidation on the adsorption mechanism of the MnO2@LDO heterostructure, detailing each component's role in the process. The results confirm the successful construction of the heterostructure and its efficient coupling of oxidation and adsorption.

Leather waste was carbonized at 800 °C in inert atmosphere. The resulting biochar was coated in situ with polypyrrole nanotubes produced by the oxidation of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity determined by four-point van der Pauw method was monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of tenths to units S cm−1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The conductivity decreased by 1–2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, viz. cationic methylene blue and anionic methyl orange, using UV-spectroscopy. The composites are designed for the future use as functional adsorbents controlled by the electrical potential.

Air pollution is related to the development of people's livelihood. As one of the main pollutants in the air, formaldehyde affects people's physical and mental health. In order to remove formaldehyde and better protect the health of residents, it is very necessary to develop efficient adsorption materials. In this study, a cellulose composite aerogel Microcrystalline Cellulose/ N-(2- aminoethyl) -3- aminopropyl methyl dimethoxysilane (MCC/APMDS) modified by APMDS was explored. The pore volume and specific surface area of the modified aerogel decreased, the average pore diameter increased, and the adsorption capacity of formaldehyde was stronger. The adsorption experiment shows that the sample prepared under the conditions of APMDS dosage of 6 wt%, reaction time of 4 h and reaction temperature of 90℃ has the largest average pore size (14.56 nm) and the largest formaldehyde adsorption capacity (9.52 mg/g). The excellent adsorption of the composite aerogel is due to high porosity and rich active amino groups on the surface. This study provides valuable information for the preparation of adsorption materials with high formaldehyde adsorption capacity for air purification.

Self-regulatory Self-efficacy belief (i.e., SRSE) represents a fundamental factor for adjustment in adolescence, as a vehicle to promote positive behaviors and protect youths from transgressions and maladjustment Bandura et al., 2003; LaRose et al., 2010). Research attested that, during adolescence, boys are more vulnerable to externalizing behaviors than girls, especially when they perceive themselves as scarcely capable of managing and orienting their behaviors, and when they possess impairments in impulsivity (Bandura et al., 2001; Muris, 2006). Previous studies firmly supported the key role of SRSE especially in the offline context in adolescence, but very few studies investigated its impact in the online context, although nowadays Internet represents one of the most significant environments for youths’ daily lives (LaRose et al., 2010; Favini et al., 2023). Thus, we aimed to examine the protective moderating role of SRSE in online and offline aggressive behaviors, beyond youths’ temperamental vulnerabilities, such as high levels of impulsivity. A sample of 318 Italian adolescents (Mage=15.21; SD=.51; 57% boys; 40% girls; 3% third gender) were asked to complete the Impulsivity Scale at Wave1, online and offline aggressive behaviors scales at Wave 2, and SRSE at Wave 2. Multiple-group-by-gender moderation model evidenced that, for what concerns online aggression, beyond the direct effects of impulsivity in boys and girls, SRSE directly affected online aggression and mediated the effect of impulsivity in girls. In contrast, impulsivity significantly affected offline aggressive behaviors only indirectly through the effects of SRSE, and SRSE directly influenced these behaviors in both genders. These results hold for the effects of youth’s age, sexual orientation, socioeconomic status, and years of education completed. This work preliminary evidenced that, contrary to previous studies which focused especially on the vulnerability of boys to aggressive conduct, impulsivity had direct effects on online aggressive behaviors in girls, and SRSE can protect adolescents of both genders in the online context, by predicting low online aggression, and represent a protective factor from the indirect effects that im-pulsivity impairments can have also in the offline context.

Biochar has high potential usage in retaining various contaminants, wastewater treatment, and water purification. In this study, three rice husk derived biochars with pyrolysis temperature 300, 400 and 500 ºC, respectively, and pristine rice rusk were used to remove cadmium from aqueous solution. The results showed that about 70% or more of Cd2+ adsorption occurred in the first 960 mins of adsorption kinetics. The Cd2+ adsorption capacity under equilibrium increased with increasing pyrolysis temperature, probably attributed to the increased specific surface area (SSA) under higher pyrolysis temperature noting that significant linear correlation occurred between Cd2+ adsorption capacity and SSA. The Cd2+ adsorption could be best fitted by pseudo-second order model relative to Elovich model and pseudo-first order model. The Cd2+ adsorption rates were higher in film diffusion stage, indicating that film diffusion stage was significant and fast in the early stage of Cd2+ adsorption. In contrast, Cd2+ adsorption by intra-particle diffusion accounted for 47.0%, 47.9% and 43.9% on average of the total Cd2+ adsorption, respectively, indicating that intra-particle diffusion of Cd2+ played a more predominant role in limiting Cd2+ adsorption rate. When reaching Cd2+ desorption equilibrium, removal ratio (RR) values were averaged 0.96, 0.91, and 0.90 under three initial concentrations. More than 90 percentage on average of Cd2+ was removed from aqueous solution by biochars and rice rusk as well, thus biochars can be used to efficiently remove contaminants from aqueous environment. Cation exchange, electrostatic attraction, and the complexation with surface functional groups could be the main dominant mechanisms for Cd2+ adsorption-desorption on biochars.

Nanometer-curved surfaces are abundant in biological systems as well as in nano-sized technologies. Properly functionalized polymer-grafted nanoparticles (PGNs) adhere to surfaces with different geometries and curvatures. This work explores some of the energetic and mechanical characteristics of the adhesion of PGNs to surfaces with positive, negative and zero curvatures using Coarse-Grained Molecular Dynamics (CGMD) simulations. Our calculated free energies of binding of the PGN to the curved and flat surfaces as a function of separation distance show that curvature of the surfaces critically impacts the adhesion strength. We find that the flat surface is the most adhesive, and the concave surface is the least adhesive surface. This somewhat counterintuitive finding suggests that while a bare nanoparticle is more likely to adhere to a positively curved surface than a flat surface, grafting polymer chains to the nanoparticle surface inverts this behavior. Moreover, we studied the rheological behavior of PGN upon separation from the flat and curved surfaces under external pulling force. The results presented herein can be exploited in drug delivery and self-assembly applications.

Previous research on consumer perceptions of salmon has often neglected Indigenous rights within the Canadian salmon industry. This study acknowledges the decline in salmon farm licenses in British Columbia and aims to achieve three main objectives: (1) gain a comprehensive understanding of four consumer perceptions—environmental sustainability, economic considerations, Indigenous rights, and price increase—across diverse consumer profiles through a cross-national online survey; (2) identify factors influencing these four consumer perceptions; and (3) assess the impact of these perceptions, along with socio-demographic variables and consumer motivations, on seven purchasing behaviors related to Canadian salmon products. Data analysis employs the graded response model and cumulative link models. The results illustrate how consumer profiles influence the four perceptions and their key determinants. Additionally, the study quantifies the impact of environmental sustainability, economic considerations, Indigenous rights, and a price increase on consumer purchasing behaviors.

Excessive online behaviors refer to harmful or disproportionate use of digital network applications. Such behaviors are likely to be associated with escapist motives. Our aim was to analyze whether escapism predicts excessive gambling, excessive gaming, and excessive internet use over time. A longitudinal sample of Finnish residents aged 18–75 years (N = 1,022, 51.27% male) was surveyed at three time points in 6-month intervals: April 2021 (Time 1), October–November 2021 (Time 2), April–May 2022 (Time 3). Of the original Time 1 respondents, 66.80% took part in the surveys at both Time 2 and Time 3. All surveys included measures for excessive gambling (Problem Gambling Severity Index), excessive gaming (Internet Gaming Disorder Test), and excessive internet use (Compulsive Internet Use Scale). Three escapism-specific questions were used to construct a dedicated escapism variable. Socio-demographic variables, alcohol consumption, and psychological distress were used as controls. The study was conducted with multilevel regression analyses using hybrid models. Our research showed that escapism had strong within-person effects on excessive gambling, B = 0.18, p = .003; excessive gaming, B = 0.50, p &lt; .001; and excessive internet use, B = 0.77, p &lt; .001 over time. The between-person effect of escapism was demonstrated on excessive gaming B = 0.91, p &lt;.001; and excessive internet use B = 0.61, p = .036. Adverse societal events and uncertain times can manifest in excessive online behaviors motivated by escapism, highlighting a need to focus prevention efforts on healthy coping methods.

Nurses’ caring behaviors are affected by several determinants. The aim of this study was to explore the factors affecting nurses’ caring behaviors. Nurses (N=309) from three public general hospitals in Greece completed the Factors of Nurses’ Caring Behaviors Scale. The data analysis was carried out with the Statistical Package for the Social Sciences (SPSS), version 26.0. Demographic and occupational data were, also, recorded. The statistical significance level was set at &lt;0.05. The total mean score on the FNCB Scale was 100.4 (SD±26). The dimensions of Workplace Circumstances (Mean: 24.6, SD±8.0) and Workload/Management (Mean: 24.5, SD±6.4) were the most important factors of caring behaviors. On the opposite, nurses perceived the dimensions of Patients’ Demographic Characteristics (Mean: 9.3, SD± 4.4) and Patients’ Clinical Characteristics (Mean: 12.5 SD±4.2) as the least important factors. Men scored higher than women in the dimension of Patients’ Demographic Characteristics (t=3.022, p=0.003). Secondary Education Graduates scored lower in the dimensions of Workplace Circumstances (Tukey, p=0.035) and Workload/Management (Tukey, p=0.033) than MSc/Ph.D. Graduates. Nurses of surgical departments scored lower in total score than ICU nurses (Tukey, p = 0.026). Workplace conditions, workload, and management seem to be the most important factors in nurses’ caring behaviors.

Keywords: Interspecific competition; Character displacements, Behavioral syndrome; Foraging; Pecking; Probing; Sweeping; Ballistic transport, Surface tension transport; Lingual transport

Activated carbon (AC) is an effective adsorbent for creatinine removal in hemoperfusion. However, the hemocompatibility and adsorption capacity of AC was required to be improved furthermore. Heparin, a widely used anticoagulant biomacromolecule, could improve the hemocompatibility of the absorbents in different ways based on its molecular weight. Thus, it was necessary to study the surface modification with unfractionated heparin (UFH) or low molecular weight heparin (LMWH) on improvement of hemocompatibility and adsorption. In this study, UFH and LMWH were respectively grafted on AC through polyethyleneimine as an intermediate layer. The modification of AC about morphology, mechanical strength and pore structure was characterized by XPS, SEM, TA and BET. It was found that compared with AC, the morphology and mechanical strength AC-UFH and AC-LMWH could be well maintained, but the BET surface was decreased due to the grafting of macromolecules. Furthermore, AC-UFH and AC-LMWH showed the better hemocompatibility on protein adsorption, APTT and platelet activation compared with AC, in which AC-LMWH had lower fibrinogen adsorption and longer APTT than AC-UFH. Besides, it was found that AC, AC-UFH and AC-LMWH had no significant effect on blood cell composition. Finally, the adsorption capacity of adsorbents for creatinine was evaluated. Although there was no significant difference between AC-UFH and AC-LMWH, it was found that heparin could be interacted with creatinine to enhance the adsorption capacity when compared with AC-PEI. This study deepened the understanding of anticoagulation of heparinized surface and provided a theoretical basis for adsorbents in hemoperfusion.

Shale gas and coalbed methane are energy sources that partly or even mainly consist of methane stored in an adsorbed state in the pores of the organic-rich rock and coal seams. In this study, the graphene nanoslit model is employed to model the nanometer slit pores in shale and coal. The Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) modelling methods are used to investigate the mechanisms of adsorption and displacement of methane in the slit pore. It was found that the CVFF forcefield resulted in the largest adsorption amount, while the PCFF forcefield resulted in the least. The COMPASS and COMPASS II force fields led to similar results. As the width of the slit pore increases, the adsorption amount of gas molecules increases, and the number density profile of adsorbed methane molecules alters from a single adsorption layer to multi-adsorption layers. The minimum slit pore width at which methane molecules can penetrate the slit pore was found to be 0.7 nm. Moreover, it is demonstrated that by lowering the temperature, the adsorption rate of the methane increases since the adsorption is an exothermic process. Enhancing methane recovery was investigated by the injection of gases such as CO2 and N2 to displace the adsorbed methane. The comparison of adsorption isotherms of gas molecules provided the following order in terms of the amount of adsorption: CO2&gt;CH4&gt;N2.

Coating of suitable materials having thickness of few atoms to several microns on a substrate is of great interest to the scientific community. Hard coatings develop under the significant composition of suitable-natured atoms where their force-energy behaviors when in certain transition state favour binding. In the binding mechanism of suitable atoms, electron belonging to outer ring filled state of gas-atom undertakes another clamp of energy knot belonging to outer ring unfilled state of solid-atom. Set process conditions develop the binding of different-natured atoms when processing their suitable composition in a system. Atoms of different nature develop structure in the form of hard coating by locating their ground points between the original ones. Here, gas-natured atoms increase the potential energy under decreasing levitational force of electrons, whereas, solid-natured atoms decrease the potential energy under decreasing gravitational force of electrons. In TiN coating, Ti–Ti atoms bind under the difference of expansion of their lattices, called nets of energy knots, where one atom just lands on the already landed atom. An adhered N-atom to a Ti-atom forms its position among four Ti-atoms where N-atom occupies the interstitial site of Ti-atoms. Two oppositely working force-energy behavior atoms deposit in the form of coating at substrate surface as per set conditions of the process. The rate of ejecting (or dissociating) solid-natured atoms depend on the nature of their source (target), process parameters and processing technique. In random arc-based vapor deposition system, depositing differently natured atoms at substrate surface depends on the input power. In addition to intrinsic nature of atoms, different properties and characteristics of coatings emerge as per engaged forces under their involved energy. The present study sets new trends in the field of coatings involving the diversified class of materials and their counterparts.

Background: Producing, distributing or discussing child sexual abuse materials (CSAM) is often committed through the dark web in order to remain hidden from search engines and regular users. Additionally, on the dark web, the CSAM creators employ various techniques to avoid detection and conceal their activities. The large volume of CSAM on the dark web presents a global social problem and poses a significant challenge for helplines, hotlines and law enforcement agencies. Objective: Identifying CSAM discussions on the dark web and uncovering associated metadata insights into characteristics, behaviours and motivation of CSAM creators. Participants and Setting: We have conducted an analysis of more than 353,000 posts generated by 35,400 distinct users and written in 118 different languages across eight dark web forums in 2022. Out of these, approximately 221,000 posts were written in English and contributed by around 29,500 unique users. Method: We propose a CSAM detection intelligence system. The system uses a manually labelled dataset to train, evaluate and select an efficient CSAM classification model. Once we identify CSAM creators and victims through CSAM posts on the dark web, we proceed to analyze, visualize and uncover information concerning the behaviors of CSAM creators and victims. Result: The CSAM classifier, based on Support Vector Machine model, exhibited good performance, achieving the highest precision of 92.3\%, accuracy of 87.6\% and recall of 84.2\%. Its prediction time is fast, taking only 0.3 milliseconds to process a single post on our laptop. While, the Naive Bayes combination is the best in term of recall, achieving 89\%, and its prediction time is just 0.1 microseconds per post. Across the eight forums in 2022, our Support Vector Machine model detected around 63,000 English CSAM posts and identified near 10,500 English CSAM creators. The analysis of metadata of CSAM posts revealed meaningful information about CSAM creators and their victims, such as: (1) the ages and nationalities of the victims typically mentioned by CSAM creators, (2) forum topics where the CSAM creators assign their posts, and (3) online platforms preferred by CSAM creators for sharing or uploading CSAM. Conclusion: Our CSAM detection system exhibits high performance in precision, recall, and accuracy in real-time when classifying CSAM and non-CSAM posts. Additionally, it can extract and visualize valuable and unique insights about CSAM creators and victims by employing advanced statistical methods. These insights prove beneficial to our partners, i.e. national hotlines and child agencies.

In this paper, the research progress on dynamic behaviors of RC structural members is reviewed from experimental, theoretical and numerical perspectives. Firstly, the basic overview, measurement methods, main conclusions and current limitations of available dynamic loading tests are presented. Then the theoretical studies on the dynamic constitutive models of RC materials, the dynamic increase factor (DIF) model for concrete and reinforcing steel and the proposed modified models of dynamic behavior parameter at the structural member level are summarized. Finally, the available modelling approach and the method for incorporating the dynamic effect in numerical simulation of RC structures are reviewed. Moreover, a brief introduction is made to the dynamic hysteretic model established on the experimental data, which provides an alternative approach to consider the dynamic effect beside the commonly used DIF method. This paper provides valuable reference for experimental studies and numerical simulations on the dynamic behaviors of RC structures, and also puts forward some issues that need to be solved in the future research works..

In the last decade, readily available electronic devices have created unprecedented opportunities for teens to access a wide variety of information and media – both positive and negative – on the internet. Despite the increasing number of initiatives taking place worldwide intended to assess and mitigate the online risks encountered by children and adolescents, there is still a need for a better understanding of how adolescents use the internet and what consequences they may face. We conducted a cross sectional online survey of a convenience sample of 733 8th and 9th grade students in Utah. The survey contained eight questions regarding students’ exposure to three types of online risk scenarios: content risk, contact risk, and commercial risk. Independent variables included students’ online behaviors, use of social media and private messaging apps, and adult supervision of online activities. Logistic and negative binomial regression models indicated that female gender, social media use, and chatting with strangers were associated with exposure to multiple unsafe online scenarios. Our results provide critical information to practitioners involved in the development of educational initiatives by building a profile of potentially risky online behaviors and allow them to tailor their initiatives to meet the needs of more vulnerable populations.

This current research follows up on Greenleaf’s oft-quoted best test of servant leadership that calls for employees to be better off financially, emotionally, physically, psychologically, etc. because of the time spent with the servant leader. While oft-quoted, little empirical work exists to see if this is true. In this study, 170 participants provided their perception of their supervisors’ level of servant leadership, their perception of the organization’s support, and their self-report of their general well-being. Gender and age bracket information described the participants, and there were no significant differences between gender or age brackets for participants’ perception of their supervisors’ servant leadership. The analysis showed that there was a moderate positive correlation between servant leadership, perceived organizational support, and general well-being. A modification of an existing general well-being instrument provided a new eight-item general well-being scale with a Cronbach’s alpha of 0.956.

Aiming at the removal of radioactive cobalt ions from water by graphene oxide (GO), the adsorption mechanism of Co2+ on graphene oxide was analyzed using the quantum chemical calculation software Gaussian 16 based on the density functional theory. The influence of material structure factors such as carboxyl group, hydroxyl group, epoxy group and graphene sheet as well as external environmental factors such as pH, temperature and interfering ions on the adsorption effect was determined, and the influence of external environment was verified through experiments. Through calculation and experiment, it was found that the existence of oxygen-containing functional groups on graphene oxide can improve the adsorption efficiency of the materialappropriately,and increasing pH under acidic conditions was also helpful to improve the adsorption effect, and the material had certain selectivity for Co2+, the adsorption capacity and selectivity could be further improved when it was modified by increasing hydroxyl group.

A novel polymer containing β-cyclodextrin, α-cyclodextrin, γ -cyclodextrin and chitosan (cy-clodextrin-chitosan) was synthesized, characterized and used for extracting two kinds of pharmaceuticals ibuprofen and progesterone. This polymer is amorphous and porous with a high swelling capacity. The cyclodextrin-chitosan polymer exhibits high extraction capacity towards progesterone and ibuprofen. Add to that, the effect of different operator variables was studied and discussed (i.e., the effects of contact time, solute concentration, pH, ionic strength and temperature). In this study adsorption kinetic was investigated, where it follows a pseudo-second order model in case of ibuprofen and progesterone.

The automotive industry is continuously seeking innovative solutions to improve the energy efficiency and sustainability of vehicles. Among the various energy-consuming systems in automobiles, air conditioning plays a crucial role. However, conventional vapour compression-based air conditioning systems are known for their high energy consumption and environmental impact. In recent years, adsorption technology has gained significant attention as a promising alternative due to its potential for higher energy efficiency and reduced greenhouse gas emissions. This review paper presents a comprehensive analysis of advancements in adsorption air conditioning technology specifically designed for automotive applications. The paper examines the recent research and development efforts in enhancing the performance and practicality of these systems, encompassing areas such as advanced materials selection, and system integration strategies. Furthermore, this review highlights the benefits and challenges associated with implementing adsorption air conditioning systems in vehicles. The environmental impact and potential for waste heat recovery are also discussed. Additionally, emerging trends, such as hybridization with conventional vapour compression systems, are explored to further optimize the energy efficiency and sustainability of automotive air conditioning. By critically evaluating the existing literature and research advancements, this review provides insights into the state-of-the-art thermally driven technologies for automotive applications.

Nowadays, there is extensive production and use of plastic materials for different industrial activities. These plastics, either from their primary production sources or through degradation processes of the plastics themselves, can contaminate the ecosystem with micro and nanoplastics. Once in the aquatic environment, these microplastics can be the basis for the adsorption of chemical pollutants, favoring that these chemical pollutants disperse more quickly in the environment and can affect living beings. Due to the lack of information on adsorption, three machine learning models (random forest, support vector machine, and artificial neural network) to predict different microplastic/water partition coefficients (log Kd) were developed using two different approximations (based on the number of input variables). The best-selected machine learning models present, in general, correlation coefficients upper than 0.92 in the query phase, which indicate that these type of models could be used for a rapid estimation of the absorption of organic contaminants on microplastics.

{This study investigates the coordinated behaviors and the underlying collective intelligence in biological groups, particularly those led by informed leaders. By establishing new convergence criteria based on real biological group experiments, this research introduces the concept of a volitional term and heterogeneous networks, constructing a coupled force Cucker-Smale model with informed leaders. The inclusion of the informed leader aspect distinctively characterizes the dynamics of leaders and followers, enabling a more accurate representation of biological group behavior. The paper then proposes the Flock Leadership Hierarchy Network (FLH), a model reflecting real biological interactions. By employing time slicing and rolling time windows, the study methodically analyses group behavior stages, using volatility and convergence time as metrics to examine the relationship between group consistency and interactions. Comparative experiments show the FLH network's superior performance. The Kolmogorov-Smirnov test indicates that the FLH network follows a power-law distribution, highlighting the evolutionary intelligence of biological groups. This research offers new perspectives on the evolution of biological groups, contributing to our understanding of both natural and artificial systems, such as animal migration and autonomous drone operations.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

Adopting banana peel as raw material, the adsorption properties of banana peel hydrothermal carbon modified with KOH solution for lead ions in aqueous solution were studied. The surface structure and functional groups of the modified hydrothermal carbon were analyzed by XRD and SEM. The results showed that the banana peel hydrothermal carbon prepared from 0.5 mol/L KOH solution had large pores, and its adsorption capacity reached 42.92 mg/g at a pH value of 6; When the concentration of KOH solution is 0.5 mol/L, the solid liquid ratio is 2 g/L, the adsorption capacity reaches 21.39 mg/g, and the adsorption rate reaches 82.74%; When the concentration of lead solution increased to 100 mg/L, the adsorption capacity of modified hydrothermal carbon for lead ions decreased to 78.26%; The equilibrium adsorption time of lead ion in solution on phosphoric acid modified hydrothermal carbon from banana peel was 250 minutes, and the adsorption process met the quasi second order kinetic model and Freundlich isotherm equation, with an equilibrium adsorption rate of 88.62%. The adsorption of lead ions in solution by KOH modified hydrothermal carbon is mainly chemical physical adsorption.

Alum sludge, an inevitable by-product from the water purification process, which had been applied as substrates in some constructed wetlands with good performance, especially for phosphorus (P) adsorption. The raw alum sludge is like clay lump with irregular shape and has a leaching concern used in the water. For a better reuse, herein, sludge was fired to produce alum sludge ceramsite (ASC) with a uniform spherical shape via four-step process of kneading sludge ball, air drying, preheating at 400°C for 10 min and firing at 600℃ for 5 min. Thereafter the physicochemical properties and P adsorption ability of ceramsite were investigated. Through XRD and FT-IR tests, there was no obvious difference between ASC and air-dried alum sludge ball (adASB) on the phase structure, but a certain amount of Al-OH group loss on the surface of ASC. The structure of ASC was still amorphous as same as adASB, while ASC possessed more micropore structure and bigger specific surface area than those of adASB. Adsorption experiments showed the P adsorption behaviors of ASC and adASB were much similar, and their adsorption kinetics all accorded with the two-step adsorption kinetics rate equation and pseudo-second-order kinetics equation. The maximum adsorption capacities of ASC and adASB fitted by Langmuir model were 1.66 mg/g and 1.89 mg/g respectively. It should be pointed that, compared with other adsorbents, ASC produced in this study still had a higher ability to adsorb P. Therefore, ASC should have a great application potential for P removal in the wastewater treatment in China.

The remarkable adsorption capacity of graphene derived materials has prompted their examination in composite materials suitable for deployment in treatment of contaminated waters. In this study, crosslinked calcium alginate – graphene oxide beads were prepared and activated by exposure to pH 4 by using 0.1M HCl. The activated beads were investigated as novel adsorbents for the removal of organic pollutants (Methylene Blue dye and the pharmaceuticals Famotidine and Diclofenac) with a range of physicochemical properties. Effects of initial pollutant concentration, temperature, pH and adsorbent dose were investigated and kinetic models were examined for fit to the data. Maximum adsorption capacities q_max obtained were 1334, 35.50 and 36.35 mg g^-1 for the uptake of Methylene blue, Famotidine and Diclofenac respectively. The equilibrium adsorption had an alignment with Langmuir isotherms while the kinetics were most accurately modelled using a pseudo- first –order and second order models according to the regression analysis. Thermodynamic parameters such as ΔG^◦, ΔH^◦ and ΔS^◦ were calculated and the adsorption process was determined to be exothermic and spontaneous.

Mineral surfaces have been demonstrated to play a central role in prebiotic reaction, which are supposed to be at the basis of the origin of life. Among the various molecules proposed as precursors for these reactions, one of the most interesting is formamide. Formamide has been shown to be a pluripotent molecule, generating a wide distribution of relevant pre-biotic products. In particular, the outcomes of its reactivity are strongly related to the presence of mineral phases, acting as catalysts toward specific reaction pathways. Even if the mineral-products relationship has been deeply studied for a large pool of materials, the fundamental description of the formamide reactivity over the mineral surface at a microscopic level is missing in the literature. In particular, a key step of formamide chemistry at surfaces is its adsorption on the available interaction sites. This report aims to investigate the adsorption of formamide over a well-defined amorphous silica, chosen as model mineral surface. An experimental IR investigation of formamide adsorption has been carried out and its outcomes have been interpreted on the basis of first principles simulation of the process adopting a realistic model of the amorphous silica.

Climate changes challenges people’s life and sustainability. Environmental problems seem to derive from human behavior. Dentistry has a high environmental footprint that needs to be controlled worldwide. Thus, the change of behavior of dentists is a necessary condition to improve the environmental situation. In this study we use a system dynamics approach to analyze pro-environmental behavior in dentists. Systemic modelling in this case, allow us to make a clear prediction of how the population of non-eco dentists will change in the future if certain factors will be affected and how much time will be needed by the system of a group of dental professionals to become eco- dentists. The ECODENT model was designed with Vensim software. It was based on the influence of WOM (word of mouth) spread of information among colleagues and stakeholders (e.g. patients, auxiliary staff and community) and other factors such as dental income, state support, CaPex and OpEx, education hours, level of urbanization and time to react. By changing each one of them we can observe the changes in the groups of non-eco and eco dentists as well as the flow of the phenomenon. It is tested that by augmenting WOM parameter, state economic support or education hours, while diminishing CaPex and OpEx, changes in pro-environmental behaviors of dentist will be reported in a shorter time. The ECODENT model can be used to further study pro-environmentalism in different dental groups and associations and design relevant eco-friendly educational programs.

The prevalence of obesity and eating disorders varies by sex, but the extent to which sex influences eating behaviors, especially in childhood, has received less attention. The purpose of this paper is to review the literature on sex differences in eating behavior in children and present new findings supporting the role of sex in child appetitive traits and neural responses to food cues. In children, the literature shows sex differences in basic taste response, food acceptance, eating self-regulation, and appetitive traits. New analyses demonstrate that sex interacts with child weight status to differentially influence appetitive traits and neural responses to food cues. Further, neuroimaging results suggest that obesity in female children is positively related to brain reactivity to higher-energy-dense food cues in regions involved with learning, memory, and object recognition, while the opposite was found in males. In addition to differences in how the brain processes information about food, other factors that may contribute to sex differences include parental feeding practices, societal emphasis on dieting, and peer influences. Future studies are needed to confirm these findings, as they may have implications for the development of effective intervention programs to improve dietary behaviors and prevent obesity.

The holy grail of Artificial Intelligence (AI) has been to mimic human intelligence using computing machines. Autopoiesis which refers to a system with well-defined identity and is capable of re-producing and maintaining itself and cognition which is the ability to process information, apply knowledge, and change the circumstance are associated with resilience and intelligence. While classical computer science (CCS) with symbolic and sub-symbolic computing has given us tools to decipher the mysteries of physical, chemical and biological systems in nature and allowed us to model, analyze various observations and use information to optimize our interactions with each other and with our environment, it falls short in reproducing even the basic behaviors of living organisms. We present the foundational shortcomings of CCS and discuss the science of infor-mation processing structures (SIPS) that allows us to fill the gaps. SIPS allows us to model su-per-symbolic computations and infuse autopoietic and cognitive behaviors into digital machines. They use common knowledge representation from the information gained using both symbolic and sub-symbolic computations in the form of system-wide knowledge networks consisting of knowledge nodes and information sharing channels with other knowledge nodes. The knowledge nodes wired together fire together to exhibit autopoietic and cognitive behaviors.

HIV incidence remains alarmingly high among female sex workers (FSWs) in low- and middle-income countries, with Uganda being no exception. The elevated risk of HIV transmission among this vulnerable population can be attributed to a complex interplay of factors, including engaging in sexual activities with multiple partners, inconsistent condom usage, substance use, and structural barriers, such as legal criminalization and pervasive stigmatization by healthcare providers. To combat this epidemic, various HIV prevention interventions have been devised, targeting these multi-faceted challenges. This study involved conducting focus groups among FSWs and healthcare providers in Uganda, with the overarching objective of informing the development of a tailored HIV prevention intervention aimed squarely at FSWs. Through these discussions, valuable insights were gained into FSWs’ perceptions of their HIV risk, their attitudes regarding HIV prevention strategies, and their recommendations regarding the content and delivery of future interventions.

The western flower thrips, Frankliniella occidentalis, is invasive and polyphagous. Its visual signal plays a crucial role in host location, suggesting that thrips has diurnal behavior. However, any diel rhythmicity of the thrips behavior is not yet well understood. This study analyzed the diurnal rhythmicity of the feeding and mating behaviors of thrips, and the patterns were explained in terms of diel rhythmicity by assessing the expression of genes associated with the circadian clock. Most feeding behaviors were observed during photophase in both larvae and adults. In mating behavior, which is mainly exhibited in 2~3 days-old young adults after emergence, most adults copulated at photophase. This diurnal pattern of the mating behavior was further supported by the analysis of a temporal calling behavior for mating, which was biased toward photophase. Four genes associated with the circadian clock were predicted in the F. occidentalis genome: period (PER), Timeless (TIM), Doubletime (DBT), and clock (CLK). All these genes exhibited a characteristic diel pattern in their gene expressions in a 24 h-period. The high expression peaks of these genes except for DBT were observed at photophase. To confirm the functional association of these genes with the feeding and mating behaviors, individual RNA interference specific to each gene was executed by feeding the gene-specific double-stranded RNA. Aside from DBT, suppression of these gene expressions resulted in significant deviations of the diel rhythms of the behaviors. These results suggest that the genetic components of the diel rhythmicity mediate the diurnal feeding and mating behaviors of F. occidentalis.

The coronavirus disease (COVID-19) vaccine is key to reducing the probability of contracting COVID-19. The vaccine is generally known to prevent severe illness, death, and hospitalization as a result of the disease and for considerably reducing COVID-19 infection risk. Accordingly, this might significantly change an individual’s perceived risk of altering everyday behaviors. For instance, the proliferation of vaccination is anticipated to reduce preventive behaviors such as staying at home, handwashing, and wearing a mask. We corresponded with the same individuals monthly for 18 months from March 2020 (early stage of COVID-19) to September 2021 in Japan to independently construct large sample panel data (N=54,007), with a participation rate of 54.7 %. We used a fixed effects model, controlling for key confounders, to determine whether vaccination was associated with a change in preventive behaviors. The major findings are as follows. Contrary to the prediction, (1) based on the whole sample, being vaccinated against COVID-19 led people to stay at home; however, it did not change the habit of handwashing and wearing a mask. Especially after the second shot, respondents were likelier to stay at home by 0.107 (95% CIs: 0.059–0.154) points on a 5-point scale compared to before the vaccination. Dividing the entire sample into young and old, (2) those aged ≤ 40 years were more likely to go out after being vaccinated, and (3) people over 40 years of age were more likely to stay at home (similar to the first result). Preventive behaviors impact all individuals during the current pandemic. Informal social norms motivate people to increase or maintain preventive behaviors even after being vaccinated in societies where these behaviors are not enforced.

Concrete is the most commonly used construction material due to its various advantages, such as versatility, familiarity, strength and durability and it will continue to be in demand far into the future. However, with today’s sensitivity to the environmental protection, this material is facing unprecedented challenges due to its high greenhouse gas emission mainly during cement production. This paper investigates one of the promising cement replacement materials, alkali activated cement (AAC) concrete. Being produced mainly from byproduct materials and having a comparable structural performance to conventional concrete, AAC concrete has a potential to transform the construction industry. Mechanical properties such as compressive and flexural strength and the relationship between them are studied. Different source materials such as fly ash (FA), ground granulated blast furnace slag (GGBS), silica fume (SF) and Metakaolin (MK) are used. The effect of the source materials and the activator solutions on the concrete performance is studied. Furthermore, the freeze-thaw resistance of the concrete is studied. The results of the study showed that the behavior of AAC depends highly on the source material combinations as well as type used. The effect of the alkaline solution is also dependent on the source material used. Mixes with higher GGBS content in general showed the highest strength while mixes with MK showed the highest flexural strength. The results from the freeze-thaw test showed that proper design of AAC concrete with a lower water content is critical to achieve a good resistance.

Understanding the strength of the associations between perceived risk and individuals’ behavioral intentions to protect their health is important for determining appropriate risk communication strategies in communities impacted by lead contamination. We conducted a survey within communities of northern Idaho, USA (n = 306) near a Superfund megasite with legacy mining contamination. We empirically test a theoretical model based on the Health Belief Model. Survey respondents had higher intentions to practice health protective behaviors when they perceived the risk of lead contamination as severe, recognized the benefits of health protective behaviors, and considered the risks of lead contamination. Women reported higher behavioral intentions than men, but age and mining affiliation did not have an association. Survey comments indicated that perceptions about the long-term environmental remediation in the region influenced risk perceptions. Understanding risk perceptions, behavioral intentions, and related factors can aid public health agencies in tailoring risk communication for increasing protective behaviors in mining-impacted communities internationally.

The research aims to resolve water pollution generated by dye wastewater. In this paper, the aminated sodium lignosulfonate (AELS) was prepared through the Mannich reaction, and the synthesis conditions were optimized using orthogonal experiments to determine the best amination conditions. The successful preparation of AELS was demonstrated through the use of FT-IR, XRD, TG, SEM and XPS characterization techniques. Then, the adsorption capacity of Methyl blue (MB) by AELS was compared in a range of different circumstances, like pH, adsorbent dose, initial concentration, time, and temperature. Additionally, the kinetics, isotherms, and thermodynamic properties of the AELS adsorption for MB were studied and discussed. The results indicated that the fitting results were consistent with the pseudo-second-order kinetic model and Langmuir isotherm model, in accordance with the mechanism of single-molecular-layer chemisorption. And the adsorption of MB by AELS was a spontaneous and endothermic process. Upon completion of five adsorption experiments, the adsorption capacity of MB by AELS was determined to be 107.95 mg g-1, which was 5.3% lower than the first experiment. This research promotes the effective use of natural resources and allows for the sustainable use of lignin and the advancement of new applications for it.

Food processing and consumption involves multiple contacts between biological fluids and solid materials of processing devices of which steel is one of the most common. Due to complexity of these interactions, it is difficult to identify the main control factors in the formation of undesirable deposits on the device surfaces that may affect safety and efficiency of the processes. Mechanistic understanding of biomolecule-metal interactions involving food proteins could improve management of these pertinent industrial processes and consumer safety in food industry and beyond. In this work, we perform a multiscale study of formation of protein corona on iron surfaces and nanoparticles in contact with cow milk proteins. By calculating the binding energies of proteins with the substrate we quantify the adsorption strength and rank proteins by the adsorption affinity. We use a multiscale method involving all-atom and coarse-grained simulations as well as generation of 3D structures of the proteins for this purpose. Finally, using the adsorption energy results, we predict the composition of protein corona on iron nanoparticles and flat surfaces via a competitive adsorption model.

Diethyldithiocarbamate (DDTC) has been employed in the sulfide ore flotation process, due to its excellent collection performance. Herein, we investigated the interfacial adsorption behavior of DDTC on four mineral phases of high-sulfur residue — sulfur, pyrite, sphalerite and lead sulfate. The adsorption behavior — adsorption structure and energy and electron localization function cross section — of DDTC and H2O were explored using density function theory calculation. The result was helpful to construct a co-adsorption model of DDTC and H2O, which was validated by the pure minerals flotation operation and the characterization of fourier transform infrared spectra. The co-adsorption model indicated that the DDTC adsorption on the sulfur, sphalerite and lead sulfate was weak with physical bonding, while its adsorption on the pyrite was strong with chemical bonding. Practical bench-scale operation of high-sulfur residue flotation was performed, whose result was different from that obtained from the pure mineral flotation. To explain the difference, our developed model predictions and the mineral fugacity pattern analysis on the high-sulfur residue flotation were synergistically used. Overall, this work first proposed the co-adsorption model of DDTC and H2O and provided important insights into the interfacial adsorption in the high-sulfur residue flotation.

Actuated carbon (AC) is utilized in various conditions of uses after its disclosure as a solid and dependable adsorbent. A review on AC is introduced along with returning to the wellsprings of AC age; strategies used to produce AC including pyrolysis enactment; actual actuation; synthetic initiation and steam pyrolysis. The significant variables influencing the AC creation, the potential uses of AC and their future possibilities are likewise examined. AC is applied in water, wastewater and leachate medicines in numerous nations, particularly to clean the shading, eliminate the smell and some substantial metals. Taking into account this, an exhaustive rundown of research on compound, physical and organic change strategies of initiated carbon relating to prevent of foreign substance expulsion from watery arrangements was aggregated and investigated. Additionally, the examination of the actual blending strategy and the impregnation technique in enactment with antacid metals shows that the actuated carbon got through actual blending had a higher porosity than the initiated carbon created by the impregnation technique. The uses of initiated carbon items were quickly surveyed.

Commercially available oxidized (carboxylic groups) and non-oxidized multiwalled carbon nanotubes were studied as adsorbents of cerium(III) in batch operation mode. Several variables affecting the rare earth adsorption were investigated, including: the stirring speed applied to the system, the pH of the solution and the metal concentration and carbon dosages. Although the removal of cerium from the solution is different and dependent upon the adsorbent type: i) adsorption in non-oxidized multiwalled carbon nanotubes, ii) cation exchange in the case of using oxidized multiwalled carbon nanotubes, the adsorption kinetics, the rate law and the isotherm models are the same for both adsorbents: pseudo-second order, film diffusion and Langmuir Type-1, respectively. Cerium is desorbed from loaded adsorbents using acidic solutions.

The harmful nature of high concentrations of antibiotics to humans and animals requires urgent development of novel materials and techniques for their absorption. In this work, CTAB (Cetyltrimethyl Ammonium Bromide)-assisted synthesis of ZIF-8 (zeolitic imidazolate framework) derived hollow carbon (ZHC) was designed, prepared and used as a high-performance adsorbent, further evaluated by Langmuir and Freundlich isothermal adsorption experiments, dynamic analysis as well as theoretical calculation. The maximum capacities of ZHC on adsorbing tetracycline (TC), norfloxacin (NFO) and levofloxacin (OFO) are 267.3, 125.6 and 227.8 mg g^-1, respectively, which delivers superior adsorptive performance when compared to widely studied inorganic adsorbates. The design concept of ZIFs-derived hollow carbon material provides guidance and insights for the efficient adsorbent of environmental antibiotics.

The adsorption of carbon dioxide on amino silanes-functionalized MCM-41 and SBA-15 materials is reported. The functionalization of mesoporous silicas was made by post-synthesis method, by impregnation of 3-aminopropyltriethoxysilane. The obtained materials were characterized by X-ray diffraction, scanning and transmission electron microscopies, nitrogen adsorption-desorption and X-ray photoelectron spectroscopy measurements. The carbon dioxide adsorption capacities for the samples were carried out under ambient pressures. The obtained results evidenced that amino-silanes with a terminal amine (–NH₂) were functionalized through covalent coupling of this group on the surface of the channels in the ordered mesoporous silica, meaning that the amine is anchored on the surface of the bigger pores of the MCM-41 and SBA-15 support. For functionalized materials, the CO₂ adsorption capacity of the AMCM-41 increased from 0.18 to 1.1 mmol·g⁻¹, whereas for ASBA-15, it was from 0.6 to 1.8 mmol·g⁻¹. The Lagergren kinetic algorithms were applied in order to validate the obtained results, evidencing the enhanced carbon dioxide adsorption capacity and stability of the functionalized ordered mesoporous molecular sieves.

This research is mainly focused on the evaluation of TiO2/Fe2O3 composite and two industrial types of waste (kaolin (Clay-K) and a blast furnace sludge (BFS)) as adsorbent materials of cyanide and as photocatalysts. First, adsorption tests were performed in the absence of light. During photodegradation experiments, the effect of the type of irradiation (ultraviolet (UV) light), visible light and natural sunlight), irradiation time, the type of photocatalyst, as well as irradiance in case of natural sunlight use, were investigated. Adsorption results indicate that Clay-K and TiO2/Fe2O3 materials adsorb approximately twice as much cyanide compared to the BFS sample, which only adsorbs 33.3% (124.87 mg/g); this is due to its smaller specific surface area (5.69 m2/g) compared to that of the other two materials (Clay-K and TiO2/Fe2O3 (14.93 m2/g and 66.59 m2/g, respectively). The results obtained from the study of photodegradation of cyanide under UV irradiation, indicate that Clay-K and BFS samples photodegrade cyanide by 96.44% and 92.66%, respectively. On the other hand, using UV irradiation plus solar irradiation and visible plus solar irradiation, the best photocatalyst was the TiO2/Fe2O3, with 98.66% photodegradation. The use of natural sunlight (irradiance of 600 to 800 W/m2) of a NaCN solution of 750 mg/L, the BFS material was the most efficient to photodegrade cyanide, obtaining 97% in two hours and 87% in just 30 minutes of irradiation.

Hierarchical micro-/mesoporous graphitic carbon spheres (HGCS) with a uniform diameter of ~0.35 μm were synthesized by Fe-catalyzed graphitization of amorphous carbon spheres resultant from hydrothermal carbonization. The HGCS resultant from 3 h at 900 °C with 1.0 wt% Fe catalyst had high graphitization degree and surface area as high as 564 m²/g. They also exhibited high specific capacitance of 140 F/g at 0.2 A/g, good electrochemical stability with 94% capacitance retention after consecutive 2500 cycles. The graphitization degree of the HGCS contributed about 60% of their specific capacitance, and their specific capacitance per unit surface area was as high as 0.2 F/m² which was much higher than in the most cases of porous amorphous carbon materials reported before. In addition, the HGCS showed a high adsorption capacity of 182.8 mg/g for methylene blue (MB), which was 12 times as high as that in the case of carbon spheres before graphitization.

The aim of this study was to investigate the knowledge, attitudes, and behaviors of family physicians regarding testicular cancer and testicular self-examination. This study was conducted with 307 physicians, including family physician specialists, family physician residents, contracted family physician specialist assistants (SAHU), and general practitioners, who agreed to participate in the study. All participants were administered a 33-item questionnaire consisting of sociodemographic questions and questions about testicular cancer and testicular self-examination, developed through literature review. Data analysis was performed using SPSS 22.0 software. 307 family physician specialists, family physician residents, SAHU residents and general practitioners participated in the study. 10.4% of the participants were working as family medicine specialists, 67.4% as family physician assistants, 13.7% as SAHU residents and 8.5% as general practitioners. The mean time spent in the profession was found to be 5.93±5.89. 65.8% of the participants thought that they had partially sufficient knowledge about testicular cancers. 57.7% of the participants stated that they did not know how testicular self-examination was performed. 49.7% of male participants stated that they had never done testicular self-exam before. While 95.8% of the participants thought that regular testicular self-examination was beneficial, 71.0% stated that they did not recommend testicular self-examination to their male patients. 53.4% of the participants thought that testicular self-examination was important; It was determined that 79.2% of them thought it was as important as breast self-examination. The rate of stating that all of the risk factors presented for testicular cancer are risks was found to be statistically significantly higher in specialist family physicians than in general practitioners and resident family physicians. The study revealed that family physicians lacked sufficient knowledge about testicular cancer and testicular self-examination, leading them not to recommend self-testicular examination to patients due to inadequate knowledge. In light of these findings, although self-testicular examination may not be recommended as a screening method, increasing awareness and knowledge among both family physicians and the public is crucial.

Using banana peel as raw material, the adsorption properties of hydrothermal carbon pre-10 pared from banana peel modified with different concentrations of phosphoric acid solution for lead 11 ions in aqueous solution were studied. The surface structure and functional groups of the modified 12 hydrothermal carbon were analyzed by XRD and SEM. The results show that the surface of the 13 modified banana peel hydrothermal carbon prepared at 240℃ and 2mol/L phosphoric acid solution 14 has large pores. The adsorption capacity is larger when pH value is 6.When the concentration of 15 phosphoric acid solution was 2mol/L, the solid-liquid ratio was 2g/L, the adsorption capacity was 16 40.64mg/g, and the removal rate was 82.74%.When the initial concentration of lead solution in-17 creased to 100mg/L, the adsorption capacity of modified hydrothermal carbon for lead ion increased 18 to 76.81mg/g, and the removal rate decreased to 76.81%.The equilibrium adsorption time of banana 19 peel phosphoric acid modified hydrothermal carbon for lead ions in solution is 300min. The adsorp-20 tion process satisfies the pseudo-second-order kinetic model and Langmuir isotherm equation. The 21 reaction temperature is 313K, and the equilibrium adsorption capacity can reach 101.19mg/g. The 22 adsorption of Pb ions in aqueous solution by phosphoric acid modified hydrothermal carbon is 23 dominated by single layer chemisorption. The artificial neural network has a fitting correlation of 24 0.99, and the adsorption process includes physical adsorption, electrostatic attraction, ion exchange, 25 and surface complexation.

Nanoporous carbons were prepared by chemical and physical activation from mangosteen peel-derived chars. The removal of atrazine was studied due to the bifunctionality of the N-groups. Pseudo-first-order, pseudo-second order and intraparticle pore diffusion kinetic models were analyzed. Adsorption isotherms were also analyzed according to Langmuir and Freundlich models. Results obtained were compared against two commercial activated carbons with comparable surface chemistry and porosimetry. The highest uptake was found for the carbons with higher content of basic surface groups. The role of the oxygen-containing groups on the removal of atrazine was estimated experimentally by the surface density. Results were compared with the adsorption energy of atrazine theoretically estimated on pristine and functionalized graphene with different oxygen-groups using periodic DFT methods. The energy of adsorption follows the same trend observed experimentally, namely the more basic the pH the more favored is the adsorption of atrazine. Micropores play an important role in the uptake of atrazine at low concentration but the presence of mesoporous is also required to inhibit the pore mass diffusion limitations. The present work contributes to the understanding of the interactions between triazine-based pollutants and the surface functional groups on nanoporous carbons in the liquid-solid interface.

Ammonia known as harmful gas that could impact on health and environment. Typically, ammonia gas emitted by fertilizer industry, rubber factory, etc. There are many options for advance industry to control ammonia gas pollution, absorption tower using water scrubber and using activated carbon as adsorption reaction could be an option. But for middle- and lower-class industry, it is common in Indonesia, as seen on many rubber factories, ammonia gas pollution is serious problem to control, actually they have used wet scrubber but eficiency is lower about 47%. This study measure performance for ammonia elimination as gas pollutant using absorption tower and adsorption tower in laboratory scale. Using electrochemical gas sensor, we measure both ammonia concentration for inlet and outlet simultaneously to settle saturation point of these two types of ammonia emission control. In conclusion, Ammonia absorbed in water proportional to saturation time and absorbent volume. Highest absorbed ammonia concentration 1.538 mg/L on 4000 mL absorbent. For Adsorption system, saturation time proportional and correlated to adsorbent weight and Adsorption capacity reverse correlated to adsorbent weight. Optimum adsorption point can be achieved from intersection curve between saturation time and adsorption capacity which is 1200 grams adsorbent

Controlling the collective behavior of micro/nanomotors with ultrasound may enable new functionality in robotic, medicine and other engineering disciplines. Currently, various collective behaviors of nanomotors, such as assembly, reconfiguration and disassembly, have been explored by using acoustic fields with a fixed frequency, while regulating their collective behaviors by varying the ultrasound frequency still remains challenging. In this work, we design an ultrasound manipulation methodology allowing nanomotors to exhibit different collective behaviors by regulating the applied ultrasound frequency. This work has important implications for design of artificial actuated nanomotors and optimize their performances.

A small but growing body of literature suggests that outdoor experiences during childhood affect environment-related behaviors in adulthood. However, research on the magnitude of the effect (effect size) of outdoor experience on learners’ behaviors remains scarce. In this study, we explore the extent to which outdoor experiences associate with environmentally responsible behaviors. Our sample consisted of 143 ninth- and tenth-grade students living on a Greek island. The data were collected using a properly adjusted environmental literacy instrument. Two different methodological pathways, i.e., a quasi-experimental approach and correlation analysis, were used to analyse the data. A tentative variable representing the frequency and intensity of students’ experiential contact with nature was found to be the strongest available predictor of their self-reported pro-environmental behaviors. The findings of this study support the significance of outdoor, experiential learning during childhood in shaping individuals’ environmental behaviors.

Nowadays, with smartphones people can easily take photos, post photos to any social networks and use the photos for some purposes. This leads to a social problem that unintended appearance in photos may threaten the privacy of photographed person. Some solutions to protect facial privacy in photos have already been proposed. However, most of them rely on different techniques to de-identify photos which can be done only by photographers, giving no choice to photographed person. To deal with that, we propose an approach that allows photographed person to proactively detect whether someone is intentionally/unintentionally trying to take pictures of him/her. Thereby, he/she can have appropriate reaction to protect the privacy. In this approach, we assume that the photographed person uses a wearable camera to record the surrounding environment in real-time. The skeleton information of likely photographers who are captured in the monitoring video is then extracted to be put into the calculation of dynamic programming score which is eventually compared with a threshold for recognition of photo-taking behavior. Experimental results demonstrate that by using the proposed approach, the photo-taking behavior is precisely recognized with high accuracy of 92.5%.

In this study, by employing the think-aloud model, schema theory and the perceptual cycle model (PCM) from the perspective of vulnerable road traffic participants, the current traffic imperfections of a target section in Wudaokou were analyzed to explore potential improvement measures to enhance safety. Specifically, the present study recruited 30 local volunteers, which were equally divided into a pedestrian group, bicyclist group and E-cyclist group. The research procedure was mainly divided into three steps. By using the think-aloud method, we analyzed and recorded the contents of oral reports of the experimental road section. Then, through translation, segmentation, coding, analysis and other techniques, we sorted and studied the report data and drew a conclusion that was universal in improving the current road traffic conditions. It is hoped that through this study, on the one hand, the applicability of the oral report method, schema theory and perceptual cycle model in road traffic safety can be verified, and, on the other hand, some better improvement measures can be extracted for the road traffic state of the Wudaokou section.

Elevated antimony concentrations in aqueous environments from anthropogenic sources is becoming of global concern, here iron oxides are known to strongly adsorb aqueous antimony species with different oxidation states, but the effect of silica on the removal characteristics is not well understood despite being a common component in the environment. In this study, ferrihydrite was synthesized at various Si/Fe molar ratios to investigate its adsorption and co-precipitation behaviors with aqueous antimony anionic species, Sb(III) and Sb(V). The XRD analyses of the precipitates showed two broad diffraction features at approximately 35° and 62° 2θ, which are characteristic of 2-line ferrihydrite, no significant shifts in peak positions in the ferrihydrite regardless of the Si/Fe ratios. The infrared spectra showed a sharp band at ~990 cm⁻¹, corresponding to asymmetric stretching vibrations of Si-O-Fe bonds which increased in intensity with increasing Si/Fe molar ratios. Further, the surface charge on the precipitates became more negative with increasing Si/Fe molar ratios. The adsorption experiments indicated that Sb(V) was preferentially adsorbed at acidic conditions and decreased dramatically with increasing pH while the adsorption rate of Sb(III) ions was independent of pH, however, the presence of silica suppressed the adsorption of both Sb(III) and Sb(V) ions. The results showed that Sb(III) and Sb(V) ions were significantly inhibited by co-precipitation with ferrihydrite even in the presence of silica by isomorphous substitution in the ferrihydrite crystal structure.

Lanthanum (La(III)) is one of the high-demand rare earth elements with applications in various products. However, La(III) in mining waste streams and electronic waste also poses environmental and health concerns. Therefore, recovery of La(III) in the waste is needed. In the present study, adsorption of La(III) with Dowex 50W-X8, Amberchrom50WX4, Amberlyst 15, and Amberchrom 50WX2 was evaluated, using a shaker water bath. Dowex 50W-X8 was found to be the best adsorbent and used to investigate the effect of the shaker speed (RPM=50-150), adsorbent dosage (1.0-4.0 g), pH (2.0-7.0), and temperature (20-40oC) on adsorption. La(III) adsorption was found to increase with the shaker speed, as expected. On the other hand, adsorption capacity decreased with the adsorbent amount. Also, the highest La(III) adsorption was observed at pH = 6.0. La(III) percentage removal didn’t vary significantly with temperature from 20 oC -40oC. However, the first-order kinetic rate constant decreased moderately with increases in temperature. Adsorption of La(III) by Dowex 50-X8 followed the Freundlich isotherm model better than the Langmuir model. In addition, adsorption kinetics was represented well by the first-order kinetic model. Moreover, enthalpy and Gibbs free energy changes were found to be negative, indicating an exothermic and thermodynamically favourable adsorption process.

Changes in the atomic and electronic structure of silicon carbide 3C-SiC (β-SiC), resulting from lead adsorption, have been studied within the density functional theory. The tests were conducted for three representative surfaces with varying degrees of lead coverage. Results indicate that chemisorption occurs, with the strongest binding, found on the hexagonal surface (111) in interaction with three dangling bonds. The adsorption energy rises with increasing coverage, especially as the surface approaches saturation. Analysis of the data was focused on parameters important for corrosion processes such as bond distances, binding energies, Bader charges and charge density difference.

The adsorption of supramolecular composites for Cs(I) in high level liquid waste (HLLW) are different due to different carriers. We chose 25,27-bis(ethyl)-calix[4]arene-26,28-crown-6 (EC[4]C6) as adsorbent, SiO2-P, XAD-7 and UiO-66 as carriers. The synthesis and characterization of supramolecular EC[4]C6 loaded with three different carriers were presented. SEM, N2 adsorption/desorption isotherms, TG-DSC spectra, FT-IR spectra results shown that EC[4]C6 was successfully introduced into the pores of carriers via physical intermolecular interactions. EC[4]C6/SiO2-P, EC[4]C6/XAD-7 and EC[4]C6/UiO-66 shown high efficiency, high selectivity towards Cs(I) over 18 typical fission or corrosion products in HNO3 solution. The adsorption properties of the three materials were investigated after electron irradiation. These results demonstrate that EC[4]C6/SiO2-P possess greater potential for highly efficient removal of Cs(I) from HLLW.