The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

Heat-treated aluminum-silicon (Al-Si)-based alloys have dominated the cast lightweight alloy industry for several decades. However, in the last decade, Al-Ce-based alloys have shown promise in replacing Al-Si alloys due to their ability to remove the need for costly heat treatments. Since the properties of Al-Ce alloys depend on the as-cast microstructure, it is important to characterize the solidification kinetics of these alloys. Therefore, this study focused on characterizing the solidification of a near eutectic Al-Ce alloy with additions of Ni and Mn. The alloy was cast in a wedge mold configuration, resulting in cooling rates between 0.18 and 14.27 °C/s. SEM coupled with EDS and DSC techniques characterized the evolution rate of solid phases. The SEM/EDS data revealed that an Al10CeMn2 phase is present at higher cooling rates. At lower cooling rates, near the center of the casting, a proeutectic Al23Ce4Ni6 phase was more present. It was observed that up to 2.6 at. % of Mn was dissolved in this proeutectic Al23Ce4Ni6 phase, thereby removing a large portion of the available Mn for forming the Al10CeMn2 phase. DSC analysis showed differences in the samples' liquidus temperatures which is indicative of compositional variations. Inductively coupled plasma atomic emission spectroscopy (ICP-OES) and Scheil solidification simulations correlated the compositional differences to phase formation, which agreed with the SEM and DSC results. This experimentation provides insight into novel Al-Ce-Ni-Mn alloys and where their potential lies in industrial applications.

Light alloys machining is a widely implemented process that have usually used in presence of cutting fluids to reduce the wear impact and increase tool life. However, current environmental protection policies require their elimination in order to improve process sustainability. This fact forces to work under aggressive cutting conditions, producing adhesion wear that affects the integrity of the part surface. This study describes cutting tool wear mechanisms in machining of UNS A92024 samples under dry cutting conditions. EDS analysis showed the different composition of the adhered layers, while roughness was also positively affected by the change of the cutting geometry produced in the tool.

Al-Zn-Mg-Cu alloy has high specific strength, good corrosion resistance, fracture toughness and fatigue resistance. It is one of the most important structural materials in the fields of aviation, aerospace, weapons, transportation and so on, which plays a huge role in the field of aerospace.In order to optimize the strength, toughness and corrosion properties of Al-Zn-Mg-Cu alloy, alloying has always been the focus of research on Al-Zn-Mg-Cu alloy. The effects of main alloying elements, trace alloying elements and rare earth elements on the microstructure and properties of Al-Zn-Mg-Cu aluminum alloy were briefly introduced in the paper, and the future research directions were prospected.

The effect of Al or Cu content on the microstructure and mechanical properties of continuous casting and extrusion Zn alloys has been studied by room temperature tensile test, X-ray diffraction, and scanning electron microscope. With the increase of Al content, the microstructure of continuous casting and extrusion Zn alloys slightly coarsens and the lamellar eutectic structure increases. The changes in the above structural factors result in a slight decrease in strength and a significant increase in elongation of Zn-Al alloys. The strength of Zn alloys increases as the Cu content increases, due to the increased content and size of the second phase in the Zn alloys. This means that the mechanical properties of Zn alloys can be adjusted by continuous casting and extrusion process, and the improvement of equipment capacity can improve the structure and morphology of the alloys.

Present work has systematically investigated the evolution of dispersoid and elevated-temperature properties including the strength and creep resistance during the various multi-step heat treatments in Al-Mn-Mg 3004 alloys. Results show that only α-Al(MnFe)Si dispersoid is observed in the studied temperature range (up to 625°C) and it coarsens with increasing temperature to 500°C but dissolves at 625°C. The evolution of elevated-temperature strength and creep resistance is greatly related to the temperature of each step during the multi-step heat treatments. Generally, lower temperature at the first-step heat treatment leads to higher properties while the properties decrease with increasing temperature of last-step heat treatment. Suitable models have been introduced to explain the evolution of strength and the creep threshold stress at elevated-temperature during the various heat treatments.

In this study, the effects of combined addition of CeLa and GdY on microstructure and mechanical properties of as-cast Al-4Cu-1Mn alloys were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopies (TEM) and tensile testing. The results show that the minor addition of CeLa and GdY leads to the refinement of grain size. The addition of CeLa results in the formation of supersaturated vacancies in the Al matrix, whereas the addition of GdY leads to a decrease in the precipitation temperature of the Al2Cu phase. The combined CeLa and GdY addition can significantly increase ultimate tensile strength (UTS) while losing only a small amount of elongation (EL). Compared with the unmodified alloy, the grain size and SDAS of the alloy (0.2 wt% CeLa + 0.1 wt% GdY) were diminished by 67.2% and 58.7%, respectively, while maximum hardness and UTS rose by 31.2% and 36.9%, correspondingly.

Imitation learning, also known as programming by demonstration, has been shown to be a promising paradigm for intuitive robot programming by non-expert users. However, the classical kinesthetic approach with physical hand guidance suffers from generalizability across different robot types and is impractical for demonstrating tasks with long horizons. Visual imitation learning enables the recording of multi-step tasks as a single continuous video, allowing non-experts to demonstrate tasks naturally. Existing approaches typically require a large amount of data to develop end-to-end deep learning models that map raw pixels to robot actions. This paper explores the application of visual imitation learning from one-shot demonstration, significantly reducing the data requirements and simplifying the programming process. To achieve this target, a framework is proposed to map hand trajectories to the robot end-effector, consisting of four essential components: hand detection; object detection; segmentation of the trajectories into elemental skills; and learning the skills. Methods are developed for each component and evaluated on recorded videos to demonstrate the effectiveness of the proposed framework.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

The principal main of this research work was the study the influence of Cu addition on the wear behavior (WB) of eutectic Al-12.6Si alloy developed by spray forming (SF) method and compared with as-cast (AC) alloys. The phases of chemical compositions and microstructure were studied by optical microscopy, energy dispersive spectroscopy (EDS) and Scanning Electron Microscopy (SEM). The microstructure of SFAl-12.6Si (SF1) alloy reside — of fine primary and eutectic Si phases evenly distributed in the equiaxed α-Al matrix and SF Al-12.6Si-2Cu (SF2) alloy lie of uniformly distributed fine eutectic Si particulates and spherical form θ-Al2Cu precipitates in α-Al matrix. On other hand, the AC Al-12.6Si alloy (AC1) alloy involve of eutectic Si needles in the dendrite α-Al matrix, whereas AC Al-12.6Si-2Cu (AC2) alloy consisted of eutectic Si needles and Chinese script form θ phase distributed randomly in the α-Al matrix. The microhardness and wear properties were analyzed using Vickers hardness (VH) and dry sliding WT. The SF alloys exhibit superior hardness compared to the AC alloys. The wear properties of SF alloys exhibited significantly superior compared to the AC alloys. The SF2 alloy showed high wear resistance (WR) than the SF1 alloy in the entire sliding velocities and applied loads. The results indicate that the spray deposited alloys have a lower coefficient of friction (CF(µ)) than the AC alloys under varying load and sliding velocity conditions. The high WR in the SF alloy was due to microstructural modification during SF and precipitation of fine Al2Cu intermetallic and solid solubility effects. The SF2 depicts increased transition from oxidative to abrasive. In other ways, AC alloys demonstrate wear mechanisms that change from oxidative to abrasive and delamination with an increase in sliding velocity and load.

A homogenization of billets from Al-Cu-Li-Mg-Sc-Zr alloys should be accomplished at high annealing temperatures exceeding 500 °C. This type of aluminum alloy is susceptible to the depletion of surface layers from Li. Therefore, choosing a suitable homogenization temperature and duration is a crucial step in assuring a homogeneous distribution of alloying elements and optimal exploitation of the potential of the alloy. In-situ heating in an electron microscope was performed on a twin-roll cast Al-Cu-Li-Mg-Sc-Zr alloy to understand the peculiarities of the homogenization process. Four types of primary phase particles rich in Cu, Li, Mg, and Fe were identified in the as-cast material. They appear as coarse particles at the boundaries of eutectic cells. Their partial dissolution occurs at temperatures above 450 °C. They are almost fully dissolved at 550 °C, except for complex phases containing Fe and Cu. Small dimensions of eutectic cells in the range of 10 µm assure a homogeneous distribution of main alloying elements within the matrix after 20 min of annealing. Direct comparison with the same material prepared by mold-casting indicates that such short annealing times result in the dissolution of main primary phase particles but do not assure a homogeneous distribution of alloying elements in the whole volume of the specimen.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

In this review, we outline our current understanding of the mechanisms involved in the absorption, storage, and transport of dietary vitamin A to the eye, the trafficking of rod opsin protein to the photoreceptor outer segments, which encompasses the logistical backbone required for visual function. Two key mechanisms of this process are emphasized in this manuscript: Ocular and systemic vitamin A membrane transporters, and rhodopsin transporters. Understanding the complementary mechanisms responsible for the generation and proper transport of the retinylidene opsin to the photoreceptor outer segment will eventually shed light on the importance of genes encoded by these proteins, and their relationship on normal visual function and in the pathophysiology of retinal degenerative diseases.

This review examines additive manufacturing for refractory tungsten (W) and its alloys. It emphasizes the primary challenges and determining factors involved in additive manufacturing pure W, W alloys, and composites. Our focus in this regard extends to both process and alloying strategies designed to address critical issues such as densification, micro-cracking, and mechanical properties in tungsten-based components produced through additive techniques. Throughout the review, we organize existing knowledge and insights into convenient tables, serving as valuable resources for researchers embarking on a deeper exploration of these topics.

A complementary characterisation of the Al-alloy EN AW-5454 was carried out, intended for obtaining the laser hybrid welding parameters of sub-assemblies in the automotive industry. The investigation included a microstructural examination, and determination of the alloy's properties using several analytical methods (HV5 hardness measurement, tensile test, Charpy impact toughness, fracture mechanics analysis). Samples were prepared in the longitudinal and transverse directions of a cold-rolled sheet of EN AW-5454 with thicknesses of 3.5 mm and 4 mm. The measured hardness on the thinner sheet was 5% higher than on the thicker sheet. The tensile and yield strength were nominal, while the elongations were smaller by 2.2 - 3.2% for the longitudinal samples and by 2.7 - 13.7% for the transverse samples. The smaller deviations from the nominal values are for the thinner sheet metal. A precise topographical analysis showed brittle fractures of the samples. The Charpy impact toughness results on the thicker plate showed a 20% greater work needed to break it in the longitudinal direction than in the transverse direction. With the thinner sheet metal, 40% greater work was needed. SEM (Scanning Electron Microscope) analysis has shown that the intermetallic Al6(Mn,Fe) particles in the longitudinal samples were mostly intact, with evidence of tough areas on the upper part of the fracture, indicating a better toughness than the specimens in the transverse direction. More crushed intermetallic particles were observed at the fractures of the transverse samples, and their distribution appeared to be more oriented in the direction of rolling. Fracture mechanics SENB (single edge notch bending) tests and their analysis showed that the resistance of the material to crack propagation in the longitudinal sample was about 50% greater than that in the transverse sample. SEM analysis of the fractures showed that the state of the intermetallic particles in the fracture mechanics testing, and the fracture mechanism differed from the one in the Charpy fractures.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

In this study, Cu/Ni and Cu/Al multilayer thin films with individual layer thickness varying from 25 nm to 200 nm were deposited at room temperature and further annealed up to 300 ℃. The mechanical and microstructural properties of the multilayers were characterized by nanoindentation, x-ray diffraction, and scanning electron microscopy. Both systems exhibited an increase in hardness with increasing annealing temperature. However, the Cu/Ni system showed a gradual and moderate (up to 30%) hardness increase from room temperature to 300 ℃, while the Cu/Al system showed a sharp increase (~150%) between 125℃ and 200℃. This distinct strengthening behavior is attributed to solid solution formation in Cu/Ni and diffusion-activated intermetallic formation in Cu/Al.

According to the requirement of 20kg load of casting barrel, we design a three-dimensional model of the robot and analyze the three stages of liquid level change in the casting barrel during the casting process. Through the analysis, it is determined that the time and angle function is an implicit function, and it is impossible to find the analytical expression of time about angle. The kinetic function of the casting barrel is simulated by MATLAB, and it is found that the function image has mutation points, and when the original function is fitted and approximated by fifth-degree polynomial interpolation, the fifth-degree polynomial function image of the time versus the angular acceleration has a large amplitude of oscillation, especially the mutation points. A PID algorithm based on the discretization of the time and acceleration function is introduced for correction, and the results show that this method effectively reduces the oscillation amplitude of the image and improves the coincidence with the original function.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Carrying out technological tests and research is indispensably connected with high costs and elongation of implementation time of new casting technologies and their modifications in industry. Hence, the application of specialised computer software, enabling the simulation and analysis of metallurgical and casting processes in modern foundry industry is of special interest. The present work presents an experimental application of MAGMASoft software in casting process of EV31A magnesium alloy structural element of helicopter engine. The results of computer simulation have been compared with industrial cast of the simulated element, fabricated in the same conditions. It has been revealed that the computer simulation provides a complex information on the analysed process, leading to reduction of costs and time, connected with technological tests in implementation of new casting technologies.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

The incorporation of polycarboxylate ether superplasticizer (PCE) type polymer and silica fume (SF) in high-performance concretes (HPC) leads to the achievement of remarkable rheological and mechanical improvements. In the fresh state, PCEs are adsorbed on cement particles and dispersants, in turn promoting the workability of the concrete. Silica fume enables a very well compacted concrete to be obtained, which is characterized by high mechanical parameters in its hardened state. Some PCEs are incompatible with silica fume, which can result in the loss of slump and in poor rheological behavior. The main objective of the research is the study of the influence of three types of PCEs, which all have a different molecular architecture, on the rheological and mechanical behavior of high-performance concretes containing 10% of SF as a partial replacement of cement. The results show that the carboxylic density of PCE has an influence on its compatibility with SF.

A new model of gravity is presented here similar to the earlier work of Verlinde on Emergent Gravity but without the use of Verlinde's main assumption on the nature of gravity as an entropic force using the First Law of Thermodynamics. Instead, the model will be shown to be consistent with the Second Law of Thermodynamics as used in Black Hole Physics. Moreover, it does not use the Equipartition Theorem such that there is no need to define a thermal bath enclosed within a holographic screen. The theory uses $E=NE_{p}$, for the total energy of a massive object where $E_{p}$ is the Planck Energy while $N$ is the number of Planck Energy to represent the maximum possible density of information that can reside in matter. The theory uses also the Holographic Principle as the basis for an information-theoretic approach to the nature of gravity. It is shown here that gravity emerges whenever there is an updating of the information within a given volume of space by the presence of matter.

Prostate cancer lung metastasis represents a clinical conundrum due to their implication of advanced disease progression and the complexities they introduce in treatment planning. As the disease progresses to distant sites such as the lung, the clinical management becomes increasingly intricate, requiring tailored therapeutic strategies to address the unique characteristics of metastatic lesions. This review seeks to synthesize the current state of knowledge surrounding prostate cancer metastasis to the lung, shedding light on the diverse array of clinical presentations encountered, ranging from subtle radiological findings to overt symptomatic manifestations. By examining the diagnostic modalities utilized in identifying this metastasis, including advanced imaging techniques and histopathological analyses, the review aims to provide insights into the diagnostic landscape and the challenges associated with accurately characterizing lung metastatic lesions in prostate cancer patients. Moreover, the review delves into the nuances of therapeutic interventions employed in managing prostate cancer lung metastasis, encompassing systemic treatments such as hormonal therapies and chemotherapy, as well as metastasis-directed therapies including surgery and radiotherapy.

In order to understand the hot deformation behavior of novel Cu/Al laminated composites, isothermal hot compression tests were conducted by Gleeble-1500D thermo-mechanical simulator. And the effect of bonding interface, deformation temperature and strain rate on the deformation behavior was analyzed. Results show that under the interface constraint effect, soft Al layer trends to flow synchronously with hard Cu layer. And further microstructure examinations indicate the cooperative deformation capability of Cu/Al composites increases with increasing stain rate and decreasing deformation temperature. Strain hardening exponent, calculated based on the true stress-true strain data, also proves the effect of deformation temperature and strain rate on the cooperative deformation behavior. Meanwhile, unique composites structure allows the Al matrix to exhibit the characteristic of dynamic recrystallization during the hot deformation process. Lastly, strain compensated Arrhenius-type constitutive equation was employed to describe the coupling effect of temperature, strain rate and strain on the flow stress.

Cost-efficient catalyst for hydrogen evolution reaction (HER) and methanol oxidization reaction (MOR) is of great importance for industrial application. The alloying of platinum with cheap transition metal offers a great opportunity to reduce cost and enhance the electro-catalytic performance. Herein, we report a simple and green route to synthesize porous Pt-Cu catalysts, where Pt-Cu solid particles were first produced by using cuprous chloride (CuCl) nanoparticles as the template, followed by a dealloying treatment to obtain final porous product. The porous alloy nanoparticles show higher catalytic activity and superior stability for HER and methanol oxidation reaction, which is beneficial from the porous structure and synergetic effect between Pt and Cu.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

The microstructure of Al-5Fe-1.5Er alloy was characterized and analyzed by using XRD, SEM, TEM and EDS. The effect of microstructure on the behavior of crack initiation and propagation was investigated by in situ tensile testing. Results show that the microstructure consists of α-Al matrix, Al₃Fe, Al₄Er, eutectic phase Al₃Fe + Al₄Er, while the 1.5 wt.% Er was added in Al-5Fe alloy. The twin structure of the Al₃Fe phase was observed, and the twin plane is {001}. Moreover, a continuous concave and convex interface structure of the Al₄Er has been found. Al₃Fe is in the form of a sheet with a clear gap inside.In situ tensile tests of the alloy at room temperature show that the crack initiation occured mainly in the Al₃Fe phase, and that the crack propagation modes include intergranular and transgranular expansion. Crack transgranular expansion is due to the strong binding ability between Al₄Er phases and surrounding organization, and the continuous concave and convex interface structure of the Al₄Er provides a significant meshing effect on the matrix and eutectic structure.

To enhance the mechanical properties (i.e. strength and elongation) of the face-centered cubic (fcc) α-phase in the Au-Cu-Al system, this study focused on the introduction of the martensite phase (doubled B19 (DB19) crystal structure of Au2CuAl) via the manipulation of alloy compositions. Fundamental evaluations, such as microstructure observations, phase identifications, thermal analysis, tensile behavior examinations, and reflectance analysis have been conducted. The presence of fcc annealing twins was both observed in the optical microscope (OM) and the scanning electron microscope (SEM) images. Both the strength and elongation of the alloys were greatly promoted while the DB19 martensite phase was introduced into the alloys. Amongst all the prepared specimens, the 47Au41Cu12Al and the 44Au44Cu12Al alloys performed the optimized mechanical properties. The enhancement of strength and ductility in these 2 alloys was achieved while the stress plateau was observed during the tensile deformation. A plot of the ultimate tensile strength (UTS) against fracture strain was constructed to illustrate the effects of the introduction of the DB19 martensite phase on the mechanical properties of the alloys. Regardless of the manipulation of the alloy compositions and the introduction of the DB19 martensite phase, the reflectance stayed almost identical to pure Au.

In this study, the hot deformation of Cu-0.55Sn-0.08La (wt%) alloy was studied by gleeble-3180 testing machine at deformation temperatures of 400-700oC and various strain rates. The stress-strain curve showed that the hot deformation behavior of Cu-0.55Sn-0.08La (wt%) alloy was greatly affected by work hardening, dynamic recovery, and dynamic recrystallization. The activation energy Q was calculated as 287.141 kJ/mol , and hot compression constitutive equation was determined as ε ̇=[sinh(0.006388σ)]^12.123∙exp⁡(37.7505-287.141/RT). The microstructural evolution of the alloy during deformation at 400oC revealed the presence of both slip and shear bands in the grains. At 700oC, dynamic recrystallization grains were observed but recrystallization was incomplete. In sum, these results provided the theoretical basis for continuous extrusion process of alloys with promising future use.

To obtain high quality grain refiner, a new Al-5Ti-1B-1RE master alloy grain refiner was synthesised by melt-matching method. Thermodynamic calculations and kinetic analyses, which were seriously missing from the study of key issues during the preparation process, were investigated. The microstructure and properties, comparison of the refining effect of different grain refiners on industrial pure aluminium and its refining mechanism were analysed with the help of X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy (SEM) and energy spectroscopy, transmission electron microscopy (TEM) and an electronic universal testing machine (CSS-44100). The experimental results show that the second-phase particles in the Al-5Ti-1B-1RE master alloy matrix synthesised by the melt-matching method are mainly TiB2、 A13Ti、Ti2A120RE, etc. The magnitude of the free energy ΔG of the synthesis reaction is calculated to be ΔGTiB2<ΔGAl3Ti<ΔGTi2A120RE. When the temperature is low (undercooling ΔT is large), the nucleation rate N mainly depends on the kinetic atomic diffusion activation energy Q, while the thermodynamic nucleation work becomes a secondary factor, and vice versa. The industrial pure aluminum refined by the new grain refiner has almost transformed from coarse columnar crystals to fine equiaxed crystals, with an average grain size of 70.2 μm, which was 36.18% and 20.66% smaller than that refined by domestic and imported Al-Ti-B wire master alloy grain refiner, and its mechanical properties of tensile strength σb was increased by 11.94%, 8.29%, and elongation at break δ was improved by 31.79%, 17.41%, respectively. The main mechanism for refining pure aluminum in Al-5Ti-1B-1RE master alloy is the formation of TiA13 on TiB2 particles, the release of RE atoms from Ti2A120RE phase surrounding TiAl3, and the partial transformation into TiA13 phase, which promotes the dual nucleation refinement mechanism and the pinning effect of rare earth elements on grain boundaries.

Transient liquid phase (TLP) bonding of Al-6063 and UNS S32304 was performed using copper foil as an interlayer between the base metals. A compression load was applied normal to the specimens. Metallurgical examination of the produced joints showed three distinct regions including a reaction zone, diffusion affected zone and the base metals. The diffusion of copper into aluminum resulted in an Al-Cu eutectic structure. However, the oxide layer on the aluminum surface controlled the dissolution behavior of copper and the extent of its wettability with the base metals. Although voids and intermetallic compounds were detected at the interfaces of the processed joints, a defect free joint was produced at 570°C. In addition, the results from corrosion tests showed that the use of copper as an interlayer decreased the corrosion resistance of the joints. However, increase in thickness of the joining reaction zone with increasing bonding temperature was observed to increase corrosion resistance.

The effect of transition metal substitution for Fe and the structural and magnetic properties of Gd2Fe16Ga0.5TM0.5 (TM=Cr, Mn, Co, Ni, Cu, and Zn) compounds were investigated. Rietveld analysis of X-ray diffraction indicates that all the samples crystallize in the hexagonal Th2Ni17 structure. The lattice parameters: a, c and unit cell volume show TM ionic radii dependence. Both Ga and TM atoms show preferred site occupancy for 12j and 12k sites. The saturation magnetization at maximum room temperature was observed for Co, Ni, and Cu of 69, 73, and 77 emu/g, respectively while minimum value was observed for Zn (62emu/g) doping Gd2Fe16Ga0.5TM0.5. Highest Curie temperature of 590 K was observed for Cu doping which is 15% and 5% and thesehigher than Gd2Fe17 and Gd2Fe16Ga compounds, respectively. The hyperfine parameters viz. hyperfine field and isomer shift, show systematic dependence on the TM atomic number. The observed magnetic and Curie temperature behavior in Gd2Fe16Ga0.5TM0.5 is explained on the basis of Fe(3d)-TM(3d) hybridization. The superior Curie temperature and magnetization value of Co, Ni, and Cu doped Gd2Fe16Ga0.5TM0.5 compounds as compared to pure Gd2Fe17 or Gd2Fe16Ga makes Gd2Fe16Ga0.5TM0.5 a potential candidate for high-temperature industrial magnet applications.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

Patient symptoms play a critical role in disease progression and diagnosis, yet they are most often captured in unstructured clinical notes. This study explores use of large language models (LLMs) for extracting patient symptoms from clinical notes, comparing their performance against rule-based information extraction (IE) systems, like BioMedICUS. By fine-tuning an LLM on diverse corpora from multiple healthcare institutions, we aimed to improve symptom extraction accuracy and efficiency with symptoms related to acute and post-acute sequelae of SARS-CoV-2. We also conducted prevalence analysis to highlight significant differences in symptom prevalence across corpora and performed fairness analysis to assess the model's equity across race and gender. Our findings indicate that while LLMs can match the effectiveness of rule-based IE methods, they face significant challenges related to demographic bias and generalizability due to variability in training corpora. This evaluation revealed overfitting and insufficient generalization, especially when models were trained predominantly on limited datasets with single annotator bias. This study also revealed that LLMs offer substantial advantages in efficiency, adaptability, and scalability for biomedical IE, marking a transformative shift in clinical data extraction processes. These results provide real-world evidence of the necessity for diverse, high-quality training datasets and robust annotation processes to enhance LLM’s performance and reliability in clinical applications.

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

Background:Boom in nanotechnology in current era has sketched unforeseen transformations in number of fields, such as medicine, health care, food, space, agriculture, etc. The synthesis of nanoparticles with different chemical compositions, sizes, shapes and controlled disparities is an important area of research in this field. Over the last decade, the biosynthesis of metal nanoparticles has received considerable attention due to their unusual and fascinating properties, with various applications, over their bulk counterparts.Hypothesis: The nanoparticle can have huge application in the field of food, pharmaceutical, and cosmetic industries and thus become a major area of research. Green synthesis of zinc oxide nanoparticles (ZnO NPs) using plant extracts offers an eco-friendly and promising substitute to the conventional methods of chemical synthesis. Conclusion: In the arena of nanoparticle phytosynthesis, novel materials have been produced that are eco-friendly, cost-effective and stable. In the current situation, nanotechnology inspires progress in all spheres of life, and therefore the phytosynthetic path of nanoparticle synthesis has emerged as a safe and best alternative to conventional methods. This review summarizes the recent work in the field of zinc nanoparticle phytosynthesis and critically discusses the mechanism proposed behind it.

Semisolid casting can provide excellent castings, but the nature of the pore-forming mechanisms has not been properly clarified. In the current communication, it was suggested that hydrogen precipitated during slurry making might have a decisive role in the formation of both gas and shrinkage porosity. Intensive stirring at the end of the slurry making process may act as a degassing step. Without the intense stirring, structures of primary slurry particles form around the hydrogen pores, strongly affecting pore formation and feeding during the intensification stage.

The corrosion inhibition effects of Drimia maritima (L.) Stearn sin. Urginea matima (L.) Backer on three different materials, i.e. as-cast Al-7 wt.% Si alloy, SAE 1020 low carbon steel and commercially pure Al samples, into a stagnant and naturally aerated 0.5 M NaCl solution are evaluated. For this purpose, both the potentiodynamic polarization curves and electrochemical impedance spectroscopy with equivalent circuit are utilized. It is found that inhibition effect in-creases up to certain minor Drimia maritima content. Adsorption isotherms (e.g. Langmuir and Temkin) have indicated that all three examined material comprise physical adsorption mecha-nism. Al-Si alloys have attained inhibition efficiency of about 96% at 25 oC with 1250 ppm of Drimia maritima, and ~43% with 625 ppm at 45 oC. On the other hand, the cp. Al and SAE 1020 samples attain ~ 89% and 68% with 1250 ppm and 500 ppm at 25 oC, respectively. This clearly in-dicates that the dosage of Drimia maritima green inhibitor into NaCl solution posses certain sus-ceptibility for each distinctive material examined. Impedance parameters obtained by using CNLS (complex non-linear least squares simulations) are correlated and discussed.

This study investigated the fatigue properties and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar welded joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Meanwhile, the fatigue life of 14 kV joints was one order of magnitude higher than that of 12 kV. The SEM observation on the fatigue fracture surface shows that the typical “tire-mark” fatigue striation just appeared on the 14 kV joint, indicating higher ductility for handling more extended plastic deformation. The high EBSD acquisition was achieved except for the transition zone due to the formation of ultra-fine nanocrystalline Al2Cu phase and amorphous phase, along with many dislocations. Dense low-angle grain boundaries (LAGBs) and refined grains are formed along the bonding interface. This indicates that severe plastic deformation induced dislocations to form the substructure in such an instant (40-60 μs) during the high-velocity collision. The interfacial strength is not only due to the continuous interfacial diffusion layer with a “wave-like” or “inverted hook-like” pattern but also benefits from refined grains along the interface and in the transition zone, as well as the hybrid amorphous-nanocrystalline microstructure, which strengthens the joint through increasing ductility induced by refined grains and regulating amorphous or nanocrystalline phases to affect the balance between strength and ductility of the Al/Cu joint.

The outdoor sculpture of the first Portuguese king, D. Afonso Henriques (~1109 – 1185 AD), placed in Guimarães (North Portugal) is one of the most emblematic national sculptures. Created in 1887 by António Soares dos Reis, it possesses a remarkable symbolic value in the presumed birthplace of the king. In addition to the artistic and heritage importance of the monument, it is one of the few sculptures cast by a Portuguese industrial foundry in the 19th-century. This study obtained data on the sculpture's elemental composition and corrosion products, gathering important historical and technical information. For this purpose, a multi-analytical approach consisting of X-ray fluorescence (XRF), X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM-EDS) was carried out to characterise the bulk metal and corrosion layers. The data revealed a ternary alloy of Cu, Sn, Zn with Pb, Fe, As, Bi and Mn as minor elements. The alloy matches that of other sculptures cast in that period. In terms of corrosion, it is characterised by the presence of oxides. These results represent the first step for applying an appropriate conservation strategy for bronze sculptures with similar characteristics.

The effect of the melt cooling rate on the atomic ordering of austenite and, as a consequence, on the martensitic transformation of a nonstoichiometric alloy of the Ni-Mn-In system has been studied. In-situ TEM observations revealed differences in the mechanism of phase transformations of the alloy subjected to different cooling conditions. It is shown that during quenching a high density of antiphase boundaries (APB) is formed and the alloy is in the austenite-martensitic (10M and 14M) state up to a temperature of 120K. In a slowly cooled alloy, a lower APB density is observed, and a two-stage transformation L21/B2 → 10M → 14M occurs in the range of 150–120 K.

Abstract: Circuit breakers are affected by multiple lightning strikes after the breaker has been tripped and can break down again, which will reduce the life of the circuit breaker and threaten the stable operation of the power system. Aiming at this problem, the paper obtained the temperature diffusion process of the inrush current process of circuit breaker opening and breaking through the schlieren technique, and combined with the existing image recognition technology to obtain the temperature characteristics of the airflow in the air gap of the contact, and the characteristics of the airflow flow. The results of the study show that the circuit breaker breakdown process generates a shock wave with a velocity approximately equal to the speed of sound under the same conditions. The maximum velocity of the airflow boundary diffusion is about 1/4 of the speed of sound under the same condition, and it decays very fast, reducing to the airflow drift velocity within 10ms after breakdown. The maximum temperature of the thermals is concentrated between 6000 and 8000 K and the temperature change is approximately inversely proportional to the square of time. The research provides the basis for the design of circuit breaker contact structure, opening speed optimization method, interrupter chamber and insulation design optimization.

Pancreatic cancer is one of the most fatal common cancers affecting both men and women, representing about 3 percent of all new cancer cases in the United States. In this study, we aimed to investigate the association of pancreatic cancer risk with alcohol consumption as well as folate intake. We performed a case-control study of 384 patients diagnosed with pancreatic cancer from May 2004 to December 2009 and 983 primary care healthy controls. Our findings showed no significant association between risk of pancreatic cancer and either overall alcohol consumption or type of alcohol consumed (drinks/day). Our study showed dietary folate intake was modestly but significantly inversely associated with pancreatic cancer (OR=0.99, P <.0001). The current study supports the hypothesis that pancreatic cancer risk is reduced with higher food-based folate intake.

The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.

Thermal analysis of a hypereutectic Al-Si alloy used for an automotive part was carried out in this research work. Solidification characteristics are recognized from the Temperature-time curve and its corresponding derivatives. This analysis was successfully used in a simulation software program with the aim of improving the resultant simulation accuracy. In this study, different types of molds, with and without cooling systems, were designed and used. The melt present in the furnaces of the factory was used to simulate the casting process. The effect of different cooling rates (1.2ºC/s, 2ºC/s, 2.3ºC/s and 2.9ºC/s) on the solidification parameters have been investigated. Differences in the resultant microstructure between wall and center of the molds have been analyzed and have been related to the T-t curve. Finally, the experimental results clearly indicate that the water-cooling rate of the molds and the melt temperature directly affects the solidification process as well as the final microstructure.

In this paper, Fe-Cr-C-N-Al-Y wear-resistant surfacing alloy was prepared by open arc surfacing with self-shielded flux-cored wire. The wear properties of the surfacing alloy were analyzed by MLS-23 rubber wheel wet sand wear tester. The phase composition and microstructure of the surfacing alloy were analyzed by XRD, SEM, EBSD and TEM, and the strengthening mechanism and wear mechanism of the alloy were discussed. The results show that the microstructure of Fe-Cr-C-N-Al-Y surfacing alloy is composed of M + γ-Fe + M7C3 + AlN. When the content of nano-Y2O3 is 0.456wt. %, the formability of the surfacing alloy is the best and the wetting angle is the smallest, which is 50.8°, AlN and M7C3 precipitate the most, and the microstructure grain is the smallest. At this time, the hardness value of the surfacing alloy is up to 62.3 HRC, which is 11.8 % higher than that of the unmodified surfacing alloy. The minimum wear weight loss is 0.125 g, and the wear resistance is increased by 41.86 %. The wear mechanism of surfacing alloy is mainly plastic deformation mechanism, and the material removal process is micro cutting and furrow wear.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

The research was undertaken to study the way deformation behaves in ultrafine-grained (UFG) conducting Al-Zr alloys doped with Sc, Hf, and Yb. All in all, 8 alloys were studied with zirconium partially replaced by Sc, Hf, and/or Yb. Doping elements (X = Zr, Sc, Hf, Yb) in the alloys total 0.4 wt.%. The choice of doping elements is conditioned by possible precipitation of Al3X particles with L12 structure while annealing these alloys. Such particles provide higher thermal stability of a nonequilibrium UFG microstructure. Initial coarse-grained samples were obtained by induction casting. The UFG microstructure in the alloys was formed by Equal Channel Angular Pressing (ECAP) at 225°C. Superplasticity tests were carried out at temperatures ranging from 300 to 500 °C and strain rates varying between 3.310-4 and 3.310-1 s-1. The highest values of elongation to failure are observed in Sc-doped alloys. A UFG Al-0.2%Zr-0.1%Sc-0.1%Hf alloy has maximum ductility: at 450 °C and a strain rate of 3.310-3 s-1, relative elongation to failure reaches 765%. At the onset of superplasticity, stress–strain curves are characterized by a stage of homogeneous strain and a long stage of localized plastic flow. The dependence of homogeneous strain (eq) on test temperature in UFG Sc-doped alloys is increasing uniformly, which is not the case for other UFG alloys with eq(T) dependence peaking at 350-400 оС. Strain rate sensitivity coefficient of flow stress m is small and does not exceed 0.26-0.3 at 400-500 °C. In UFG alloys containing no scandium, m coefficient is observed to go down to 0.12-0.18 at 500 оС. It has been suggested that lower m values are driven by intensive grain growth and pore formation in large Al3X particles, which develop specifically at the ingot crystallization stage.

A homogenized, supersaturated Al-Zn-Mg-Zr alloy was processed by severe plastic deformation (SPD) using high-pressure torsion (HPT) technique for different revolutions at room temperature to get ultrafine-grained (UFG) microstructure. The microstructure and mechanical properties of the UFG samples were then studied by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), as well as by tensile and hardness measurements. Emphasis was placed on the effect of shear strain on the evolution of microstructure of the investigated alloy. Experimental results have shown a very interesting evolution of the decomposed microstructure in a wide range of shear strains imposed by HPT. While the global properties, such as the average grain size (~200 nm) and hardness (~2.2 GPa) appeared unchanged, the local microstructure was continuously transformed. After 1 turn of HPT, the decomposed UFG structure contains relatively large precipitates inside grains. In the sample processed by 5 turns in HPT, segregation of Zn atoms into grain boundaries (GBs) can also be observed. After 10 turns, more Zn atoms have segregated into GBs and only smaller size precipitates can be observed inside grains. The intensive segregation of solute atoms into GBs may significantly affect the ductility of the materials, leading to its ultralow-temperature superplasticity. Our findings pave the way for achieving advanced microstructural and mechanical properties in nanostructured metals and alloys by engineering their precipitation and segregation by means of applying different HPT regimes.

In the context of high-temperature water vapor treatment, Zn-Mg-Al alloy-coated steel sheets exhibit the emergence of a black surface. This study aims to explore the factors and mechanisms contributing to surface blackening by inducing black surfaces on Zn-Mg-Al alloy-coated steel sheets, which were fabricated through molten coating subjected to water vapor treatment at 150 degrees Celsius. The surfaced composition was predominantly identified as ZnO, a zinc oxide film, validated through X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Morphological analysis of the surface and cross-section post-water vapor treatment revealed a disrupted lamellar structure with diffused features, resulting in the formation of an oxide film. Optical properties analysis demonstrated an increased absorbance and a decreased bandgap energy after water vapor treatment, indicative of an augmented blackening effect. Consequently, the high-temperature water vapor treatment led to the formation of oxides on the surface, with the highly reactive Mg and Al extracting oxygen from the predominantly present ZnO surface. This process resulted in the creation of an oxygen-deficient oxide, ultimately causing surface blackening.

The interference-fit size has a significant effect on CFRP/Al-alloy laminates riveted lap joints, the requirements for the interference-fit size are different because of the strengthening of heterogeneous materials. However, in the process of the riveted CFRP/Al-alloy, the heterogeneous laminates lead to poor structural strength because of the different requirements of interference-fit size. Therefore, the different assembly types of riveting mold are designed to acquire a novel interference-fit size, and the tensile test is adopted to evaluate the tensile property. In addition, the fracture failure of CFRP/Al-alloy laminates riveted lap joint is observed by the ultra-depth of field microscope. Finally, the best assembly type is the trapezoid riveting mold combined with an arc riveting die, and the sidewall intersection angle of the trapezoid riveting mold is 66° which could achieve a suitable interference-fit size and a better mechanical performance.

The effect of retrogression re-aging treatment (RRA) on corrosion behavior of 7055 Al-Zn-Mg alloy were studied. Results provides the corrosion resistance could be greatly improved by RRA. After the RRA treatment, the isolated precipitates occurred on grain boundaries (GBs) and the low angle grain boundaries (LAGBs) presented a larger fraction compared to the single-stage peaking aging. The samples after RRA treatment also show better corrosion resistance than the single-stage peak aging. The results of electrochemical impedance spectroscopy (EIS) show that impedance spectrum is consisted of semi-infinite layer diffusion impedance and stagnant Weber impedance. The semi-infinite layer diffusion impedance corresponded a limited retention layer on the electrode surface. In corrosion process, Weber impedance corresponded to stagnant layer of corrosion products generated by the anode branches. The RRA sample has the high Rf and low Cf, Cp values, and the corrosion current density of the RRA samples is ten times less than the single-stage peak aging samples with the 10% hardness losing.

Two new coordination compounds of Mn(II) and Cu(II) viz. [Mn(bz)2(Hdmpz)2(H2O)] (1) and [Cu(crot)2(Hdmpz)2] (2) (where, bz = benzoate, crot = crotonate, Hdmpz = 3, 5-dimethyl pyrazole) have been synthesized and characterized using single crystal X-ray diffraction technique, FT-IR, electronic spectroscopy, TGA and elemental analyses. Compounds 1 and 2 crystallize as mono-nuclear coordination compounds of Hdmpz based penta-coordinated Mn(II) and hexa-coordinated Cu(II) respectively containing distorted trigonal bipyramidal and distorted octahedral geome-tries. Crystal structure analysis of compound 1 reveals the presence C‒H⋯π and π-stacking in-teractions along with O‒H⋯O, N‒H⋯O and C‒H⋯O H-bonding interactions which stabilizes the layered assembly of the compound. Similarly, the presence of hydrogen bonding along with π-stacking interactions stabilizes the crystal structure of compound 2. We have carried out theo-retical investigations to analyze π⋯π H-bonding and antiparallel CH···π non-covalent interac-tions observed in the compounds. DFT calculations were performed to evaluate strength of these interactions energetically. Moreover, QTAIM and non-covalent interaction (NCI) plot index computational tool were used to characterize them and evaluate the contribution of the H-bonds.

The effects of various drawing parameters and annealing processes on the structure and properties of Cu-Ag wires, containing 1 wt% silver, were investigated using specialized equipment including fine wire drawing machines, very fine wire drawing machines, heat treatment equipment, tensile testing machines, microcomputer-controlled electronic universal testers, resistance testers, and scanning electron microscopes. The results revealed that continuous drawing of Cu-1%Ag alloy wires led to elongation of the grains, resulting in a uniform and tightly fibrous microstructure. Moreover, the tensile strength of the alloy wire increased from 670 MPa to 783.9 MPa after a single-pass with a deformation of 14%. Subsequently, when the wire was drawn at a speed of 500 m/min, the tensile strength further increased to 820.1 MPa. After annealing the Փ0.08 mm Cu-1% Ag alloy wire, an increase in annealing temperature up to 500°C resulted in the wire's tensile strength decreasing from 820.1 MPa to 377.5 MPa. Simultaneously, the elongation increased from 1.94% to 15.21%, and the resistivity decreased from 1.931×10-8Ω·m to 1.723×10-8Ω·m. Additionally, when annealing was conducted at a rate of 80 m/min, the wire resistivity dropped to 1.635×10-8Ω·m.

Due to the difficult metallurgical conditions during production, advanced processing techniques are required to produce functionally graded metal matrix composites. In this study, we explored a novel approach by using a combination of two different methods to produce Functionally Graded 7075 Al / SiCp composites. First process was direct semi-solid stirring that was used to prevent particle agglomeration, brittle reaction products, floating or settling of the reinforcements and poor wettability for the production of SiCp (wt. 5-20%) reinforced aluminum matrix composites. In the direct semi-solid mixing process, the matrix material remains in a semi-solid state until the reinforcement addition process is completed. The second novel process was sequential squeeze casting to provide liquid diffusion between two composite layers that were used to produce functionally graded aluminum matrix composite. The microstructure and interlayer zones were characterized by using optical microscopy and scanning electron microscopy. The resulting functionally graded material was subjected to spectrometer analyses, density measurements, and metallographic examinations in order to determine the characteristics of its layers and interfacial zones, as well as to assess the formation of the graded structure. The results obtained from this research provide the potential to use this new combined manufacturing method, which is relatively inexpensive, efficient and easily applicable, in order to produce functionally graded SiCp reinforced aluminum composites.

The microstructure evolution and grain refinement kinetics of a solution treated Cu – 0.1Cr – 0.06Zr alloy during equal channel angular pressing (ECAP) at a temperature of 673 K via route B_C were investigated. The microstructure change during plastic deformation was accompanied by the microband formation and an increase in the misorienations of strain-induced subboundaries. The refinement of initial coarse grains was considered as a result of continuous dynamic recrystallization. The dynamic recrystallization kinetics was discussed in terms of grain/subgrain boundary triple junction evolution. The strain dependence of the triple junctions of high-angle boundaries can be expressed by a modified Johnson-Mehl-Avrami-Kolmogorov relationship with a strain exponent of about 1.49. Severe plastic deformation by ECAP led to substantial strengthening of the Cu-0.1Cr-0.06Zr alloy. The yield strength increased from 60 MPa in the initial state to 445 MPa after the total strain of 12.

Additive manufacturing (AM) provides customization of the microstructure and mechanical properties of components. Selective laser melting (SLM) is the commonly used technique for processing high strength Aluminum alloys. Selection of SLM process parameters could control the microstructure of fabricated parts and their mechanical properties. However, process parameter limits and defects inside the as-built parts present obstacles to customized part production. This study is the second part of a comprehensive work that investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. Mechanical properties of the parts were illustrated by regression models generated with design of experiment (DOE) analysis. The results reported in this study were compared to previous studies, illustrating how the process parameters and powder characteristics could affect the quality of produced parts.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

The corrosion behavior of Fe-containing directionally solidified (DS) and centrifugally cast (CC) Al-Si-Cu-Zn alloys with either Co or Ni additions has been investigated. Electrochemical and immersion corrosion methods were used to investigate the corrosion behavior in 0.6 M NaCl after short (1-hour) and long (30-day) exposure periods. The employed solidification methods allowed the production of samples with a wide range of secondary dendrite arm spacing (SDAS) while preserving Si and Fe-containing phases. The 0.5 wt.% Ni and Co additions led to the growth of the AlFeSi(Ni) and AlFeSi(Co) phases, but no binary AlNi nor AlCo intermetallic par-ticles have been generated. Potentiodynamic polarization studies at early exposure revealed an increase in the corrosion potential as the Ni was added for either fast or slow solidified samples. The electrochemical impedance spectroscopy at early exposure demonstrated that the Ni-modified alloy, on the other hand, was associated to smaller charge transfer resistances, in-dicating a reduction in corrosion resistance after short elapsed time into the electrolyte. Howev-er, 30-day immersion tests revealed much lower corrosion rate of the Ni-modified alloy than the other alloys, while the corrosion rates of the Co-modified and non-modified alloys were simi-lar. In the Ni-containing alloy, decreased corrosion rate under long-term corrosion process was attributed to the formation of a thick and dense alumina layer, effectively protecting the surface under such conditions. This work contributes to a better knowledge of the corrosion behavior of Ni- and Co-corrected Al industrial scrap compositions.

this paper focuses on a scientific study of the restoration, rehabilitation and reuse of the great throne hall, the most important hall in al-jawhara palace. it also aims to study the most important factors and forces of damage that affected the great throne hall, natural, biological, and human, and the resulting damage. field tests were performed, laboratory tests to determine fracture stress, liquidity and spandex limits tests, chemical analysis on soil samples and geoelectrical testing of the soil, and the results did not show caves or voids in the ground until a depth of 10.00 m, construc-tion materials were studied and tested using x-ray, (xrd), mechanical tests (tensile, shear, com-pression), and a study of the effect of seismic loads on the walls; the results showed horizontal and vertical cracks; based on the study and analysis of these cracks, it was possible to present modern techniques in restoration and reinforcement methods, and in conclusion, the researcher's recommendations.

The effects of partial replacement of Si by Al on the microstructure, tensile properties, and Charpy impact toughness were investigated using 0.2%C-Si/Al-Mn-Cr-B TRIP-aided martensitic steels. The impact toughness was related to the microstructural and mechanical properties. The partial re-placement decreased the volume fraction of retained austenite and increased the mechanical stabil-ity, accompanied by softening and an increase in the volume fraction of the primary martensite. Resultantly, the partial replacement decreased strength and ductility. The impact absorbed energy (value) at 25 C was slightly increased by the partial replacement. The increased impact absorbed energy was mainly caused by high crack/void propagation energy due to the softened primary martensite and a small contribution of the stabilized retained austenite. The 50% shear fracture ductile-to-brittle transition temperature was marginally raised by the partial replacement. The raised transition temperature was mainly associated with an increase in a unit crack path of qua-si-cleavage/cleavage fracture.

This research investigates the impact of Al and Ti elements on the formation of self-generated ordered phase in high-entropy alloys (HEA), which have been receiving widespread concentration in present times thanks to their remarkable multifunctional properties and wide range of component selection. By adjusting the dual elements of Al and Ti, the study explores the regulation of quantity and distribution of the in-situ self-generated ordered phases in the alloy. The results of the annealing heat treatment process demonstrated that, through accession Al and Ti elements, the Cr-Fe-Ni medium-entropy alloy transfer from BCC phase to BCC+FCC phase and the precipitation of new phases such as B2, L21, and σ. This led to a synergistic impact of second phase strengthening, and also of solid solution strengthening, resulting in improved compressive properties of HEA.

Precipitates are the primary source of strength for the Al-Mg-Si alloy. Aluminum alloy in the peak-aged state mainly contain β'' and β' precipitates. In the past, most of the literature only considered the strengthening effect of β''. Here we develop a single crystal intensity model including both precipitate enhancement effects for the first time. This model was subsequently implemented into a crystal plastic finite element method to model the uniaxial tensile process of a polycrystalline aggregate model of Al-Mg-Si alloy. The simulation results for uniaxial stretching are in good agreement with the experimental results, confirming that the constitutive parameters used for the single crystal strength model with two precipitates are based on realistic physical implications. Furthermore, by comparing the uniaxial tensile simulation results of a peak-aged alloy considering the actual precipitated phase composition of the alloy with those assuming that the precipitated phase is only the β'' phase, the predicted tensile strength of the former is around 5.65% lower than that of the latter, suggesting that the two kinds of precipitation should be considered separately when simulating the mechanical response of Al-Mg-Si alloy. It is highly expected that the present simulation strategy is not limited to the Al-Mg-Si alloys, and it can be equally applied to the other age-enhanced alloys.

The present study aimed to investigate the effect of cold deformation on the precipitation kinetics of a binary CuSc alloy containing 0.4 wt.% scandium using the experimental analysis method of differential scanning calorimetry (DSC). Non-deformed and 75% cross-section reduced cold-rolled, supersaturated specimens were tested at non-isothermal DSC runs at up to five different heating rates. The DSC results showed that cold deformation significantly accelerated the precipitation process in the binary alloy, leading to a decrease in the initial and peak temperatures of the exothermic reactions. The activation energies calculated with the Kissinger method, indicated that the precipitation activation energy decreased with increasing cold deformation. The findings of this study provide worthy implications to further optimize the processing of Cu-Sc alloys with improved mechanical properties.

We studied Ni2FeSi, Co2FeSi and Co2MnSi -based full Heusler alloy glass-coated microwires with the same geometric aspect ratio ρ ≈ 0.50 ± 0.01 prepared using Taylor-Ulitovsky method. The fabrication of X2YZ; (X = Co &amp; Ni, Y = Fe &amp; Mn and Z = Si) based glass coated microwires with fixed aspect ratio is a quite challenging due to the different samples preparation conditions. The XRD analysis shows nanocrystalline microstructure for all the samples. Space group Fm3¯m (FCC) with disordered B2 and A2-types for Ni2FeSi and Co2FeSi and ordered L21-type for Co2MnSi are observed. The change in the positions of Ni, Co and Mn, Fe in X2YSi resulted in a variation in the lattice cell parameters and the average grain size of the sample. Room temperature magnetic behavior shows a dramatic change depending on the chemical composition, where Ni2FeSi-MWs shows the highest coercivity (Hc) compared to Co2FeSi-MWS and Co2MnSi-MWs. The Hc –value of Ni2FeSi-MWs is 16 times higher than that of Co2MnSi-MWs and 3 times higher than that of Co2FeSi-MWS. Meanwhile, the highest reduced remanence is reported for Co2FeSi-MWS (Mr =0.92), , being about 0.33 and 0.22 for Ni2FeSi-MWs and Co2MnSi-MWs, respectively. From the analysis of the temperature dependence of the magnetic properties (Hc and Mr) of X2YZ-MWs we deduced that Hc shows a stable tendency for Co2MnSi-MWs and Co2FeSi-MWs, meanwhile two flipped points are observed for Ni2FeSi-MWs where the behavior of Hc changes with temperature. For Mr monotonic increase by decreasing the temperature is observed for Co2FeSi-MWs and Ni2FeSi-MWs and roughly stable for Co2MnSi-MWs. The thermomagnetic curves at low magnetic field show irreversible magnetic behavior for Co2MnSi-MWs and Co2FeSi-MWs and regular ferromagnetic behavior for Ni2FeSi-MWs. The current result illustrates the ability to tailor the structure and magnetic behavior of X2YZ-MWs at a fixed internal stresses, i.e., with fixed aspect ratio. Additionally, a different behavior was revealed in X2YZ-MWs depending on the degree of ordering and elements distribution. The tunability of magnetic properties of X2YZ-MWs makes them suitable for sensing applications.

Zirconium based bulk metallic glasses are industrially valuable materials which commercial market grows rapidly. Surface modification of these metallic glasses by high-intensity lasers is relatively new and costly treatment promising great advantages over classical surface processing methods. In this work we perform the case study of surface modification of Zr$_{46}$Cu$_{36.8}$Ag$_{9.2}$Al$_8$ metallic glass by high-intensity millisecond laser beam. Our results suggest chemical deposition of atmospheric oxygen and nitrogen in the laser-melted surface area and its surroundings. Zirconium nitride layer was detected in the middle of laser-irradiated area. Nanocrystals embedded in the amorphous matrix were also formed on the surface. Overall, our findings suggest possibilities for improvement of mechanical characteristics of the studied metallic glass.

The aim of this work is to assess the influence of Friction Stir Welding (FSW), process parameters, optimized tool traveling speed, and corrosion resistance of the 0.95 Mg-Al-alloy and pure copper weldment. Samples of aluminum-copper with and without deformation were characterized to investigate the metallurgical effects created during the welding deformation process. Effect of process parameters on microstructure and corrosion rate have been investigated for all the samples. All the electrochemical and polarization tests were done in 3.5 wt.% NaCl solution. Scanning Kelvin Probe (SKP) was done to detect the localized corrosion on the surface. Optical micrography observation indicated that the primary α-Al phase, which was formed during solidification can effectively limit the growth of Cu₉Al₄ phase. Finer acicular α-Al precipitates were observed in CuAl matrix during joining process that tends to coarser with the increase in tools travel speed. The electrochemical and polarization results showed that among all the tool travelling speed the specimen joined at tool travelling speed of 40 mm/min shows the best non-corrosive property.

This research aims to understand the vision and the reaction of the population towards tourism and holidays during this period of the COVID-19 pandemic. It investigates also the tourist needs of the Algerian population after the closure of international borders. Methods: The data were collected using mixed quantitative and qualitative methods through a questionnaire applied to 203 people in different regions of Algeria (a North African country) from 1st June to 13 July 2020. Results: The needs of Algerian tourists are characterized by a great need for leisure to relieve psychological stress caused by COVID-19 (M = 25.33) among the study sample (p <0.05). The results also show an average need to rationalize the costs of tourist services (M = 5.26) according to the respondents (p <0.01). This is in addition to the great need (M = 7.75) among respondents (p <0.05) of the awareness that the tourism sector can contribute to the economic recovery in Algeria after the confinement period. About 75.86% of respondents demand the cleanliness of tourist sites, while 69.95% recommend improving safety because of the size of tourist sites in the Algerian territory and also measures related to social distancing. The results show that 53.69% of respondents preferred the month of August to go on vacation, 29.06% chose the month of September, and 17.25% would prefer the months of October, November and December since they expect a reduction in the risks of the COVID-19 pandemic. Conclusions: The COVID-19 pandemic has affected the tourism needs of the Algerian population, which has become increasingly aware of the consequences of the pandemic in relation to their health and on the country's economy. These results can help the authorities of the tourism sector to better understand and identify the tourism needs of this population in the current period and after the COVID-19 pandemic.

The high flammability and lack of charrability of polystyrene (PS) pose significant limitations on its broader applications. Therefore, there is an urgent need for a straightforward and efficient method for the synthesis of flame-retardant PS, which still poses a considerable challenge. In this study, we present an efficient approach to enhance the flame-retardant properties of PS through direct phosphorylating aromatic C(sp2)-H bonds using commercially available and inexpensive manganese catalyst. A range of phosphonates served as reactive substrates to enable a tunable degree of polymer functionalization. The corresponding phosphorylated PS specimens were determined by means of 1H NMR, 31P NMR, FTIR spectroscopy and GPC. Microscale combustion calorimetry (MCC) tests indicate that this protocol indeed enhances the flame-retardant performance of PS. Moreover, other advantages associated with the incorporation of the phosphonate group have been observed, including improved thermal resistance and wettability. This cost-effective strategy of Mn-catalyzed C-H can also be utilized to directly obtain phosphonate modification of waste foamed PS and styrene acrylonitrile copolymer, providing a new method for the purpose of recycling and upgrading PS plastics.

Super-hydrophobic surfaces and coatings have stimulated a great deal of research, with the aim to achieve better wetting properties. Factors such as surface chemistry and roughness play an important role in changing the surface energy, which in turn leads to changes in the wettability. Here, we have analysed the time dependence of the oxide layer and possible surface adsorbates on the surface topography of an Al59Cu25Fe13B3 quasicrystalline material for changes to the wettability. The quasicrystalline matrix phase was 94 % of the sample volume, and covered by a very smooth, amorphous oxide layer. The AlB12 and AlFe2B2 boron-rich phases were embedded in the quasicrystalline material as a result of a 3 at.% boron addition, which makes atomisation of the material a simpler process. Under ambient conditions the sample was naturally covered by an oxide layer; therefore, it is referred to as “surfenergy”, to distinguish it from the conventional surface energy of a bare quasicrystal surface. The growth of the oxide layer with atmospheric ageing and annealing at 500° C in air for various times was investigated for both cases. The phase most prone to oxidation was the boron-rich AlFe2B2, which influenced the topography of the surface and accordingly the wetting behaviour of the specimen. We demonstrated that the surfenergy depends on the polar component, which is the most sensitive to the operating conditions. A correlation between the surfenergy components and the surface roughness was found. In addition, theoretical models to determine the wettability were included.

Spectroscopic methods are used to study the processes of accumulation of electron and hole trapping centers and energy transfer of electronic excitations to impurities in CaSO4-Mn and BaSO4-Mn. It is shown that the transfer of energy from the host to impurities occurs at the moment of charge transfer from the excited anionic complex SO_4^(2-) to the hybrid radiative electronic states at 2.95–3.1 eV formed from the electronic states of the Mn^(+)-SO_4^(-) and SO_4^(3-)-SO_4^(-) trapping centers. It was found that, in sulfates, under irradiation, as a result of charge transfer from excited anionic complexes of the host to the excited states of impurities Tl^(+),Cu^(+),Mn^(2+), hybrid radiative states emerge at 2.95–3.15 eV, occupying the same energy levels as the intrinsic electronic trapping center SO_4^(3-) of the host at 2.95–3.1 eV.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

Iron and chromium based alloys have found wide application in various fields of science and technology. Primary carrier based on Fe-Cr-Al alloy is used in block catalysts for high-temperature hydrocarbon conversion, in production of block metal catalysts for neutralization of toxic gases released during operation of internal combustion engines, as well as those present in smoke emissions from enterprises. Influence of thermal action on Fe-Cr-Al alloy foil and stability of secondary carrier on its surface was studied. Elemental composition of the surface layer of X15U5 alloy foil does not remain constant during heating and depends on the thermal treatment mode. Some of the elements come to surface and elemental composition of surface layer can differ significantly from that observed in the bulk of foil sample. This implies the possibility of changing the adhesive and adsorption properties of the foil surface, as well as the need to take this fact into account when supporting a secondary carrier and active phase to the foil. Applied technique of phosphating and supporting a secondary carrier to the foil surface makes it possible to obtain a sufficiently stable coating. There is no shedding of the secondary carrier from foil surface during high-temperature treatment in air.

Given of the outstanding versatile properties, the multilayered anti-corrosion coatings have drawn great interests in academic and engineering fields. However, the application of multilayered coatings is restricted by some limitations such as low interlayer compatibilities, harsh preparation process, etc. This work introduced a composite film fabricated on 2A12 aluminum alloy surface, including an anodic oxide film, a sol-gel film as well as a layer-by-layer (LBL) self-assembling film from bottom to top. The microstructure and elemental characterization indicated that the finish of the coating with the LBL film resulted in a closely connected multilayered coating with a smoother surface. The anticorrosion performance was systematically evaluated in the simulated corrosive medium and neutral salt-spray environment. The intergrated coating with the LBL film presented an excellent anticorrosion ability with the system impedance over 108 Ω•cm² and the self-corrosion current density two orders of magnitude lower than that of the other coatings. After the acceleration test in salt-spray environment, the multilayered coatings could still show a good protective performance with almost no cracks and no penetration of chloride ions. It is believed that the as-constructed multilayered coating with high corrosive properties and fine surface state will have promising applications in the field of anticorrosion engineering.

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

Iron deficiency in the fetal and neonatal period (perinatal iron deficiency) bodes poorly to neuro-development. Given its common occurrence and the negative impact on brain development, a screening and treatment strategy that is focused on optimizing brain development in perinatal iron deficiency is necessary. Pediatric societies currently recommend a universal iron supple-mentation strategy for full-term and preterm infants that does not consider individual variation in the body iron status and could lead to under-treatment or over-treatment. Moreover, the focus is on hematological normalcy and not optimal brain development. Several serum iron indices and hematological parameters in the perinatal period are associated with risk of abnormal neurodevelopment, suggesting their potential use as biomarkers for screening and monitoring treatment in infants at risk for perinatal iron deficiency. A biomarker-based screening and treatment strategy that is focused on optimizing brain development will likely improve outcome in perinatal iron deficiency.

Controlling and understanding Cu-catalyzed homocoupling reaction is crucial to prompt the development of efficient Cu-catalyzed cross-coupling reactions. The presence of a coordinating base (hydroxide, methoxide) enables the B-to-Cu(II) transmetalation from aryl boronic acid to CuIICl2 in methanol, through formation of a mixed Cu-(μ-OH)-B intermediates. A second B-to-Cu transmetalation to form bis-aryl Cu(II) complexes is disfavored. Instead, organocopper(II) dimers undergo a coupled transmetalation-electron-transfer (TET) allowing the formation of a bis-organocopper(III) complexes readily promoting reductive elimination. Based on this mechanism some guidelines are suggested to control the undesired formation of homocoupling product in Cu-catalyzed cross-coupling reactions.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

Cardiovascular diseases (CVDs) constitute the first cause of death among the population of developing and developed countries. Atherosclerosis, which is a disorder with multifactorial etiopathogenesis, underlies most CVDs. The available literature includes ample research studies on the influence of classic cardiovascular (CV) risk factors. However, environmental exposure to heavy metals, among other substances, is still an unappreciated risk factor of CVDs. This study aimed to assess the concentration of some heavy metals (copper (Cu), zinc (Zn), manganese (Mn), cobalt (Co), and iron (Fe)) in the blood serum of postmyocardial infarction (post-MI) patients and patients free from myocardial infarction (MI) as well as estimate the relationship between the occurrence of MI and increased concentration of heavy metals. The concentration of heavy metals (Cu, Zn, Mn, Co, and Fe) was assessed using the inductively coupled plasma mass spectrometry technique in a group of 146 respondents divided into two groups: post-MI group (study group (SG), n = 74) and group without cardiovascular event (CVE) having a low CV risk (control group (CG), n = 72). The concentration of the analyzed heavy metals was higher in SG. All the heavy metals showed a significant diagnostic value (p < 0.001). The highest value of area under the curve (AUC) was observed for manganese (Mn) (0.955; 95% confidence interval (CI) = 0.922–0.988), while the lowest value was found for zinc (Zn) (0.691; 95% CI = 0.599–0.782). In one-dimensional models, high concentrations of each of the analyzed heavy metals significantly increased the chances of having MI from 7-fold (Cu) to 128-fold (Mn). All the models containing a particular metal showed a significant and high discrimination value for MI occurrence (AUC 0.72–0.92). Higher concentrations of Cu, Zn, Mn, Co, and Fe were found to considerably increase the chances of having MI. Considering the increasingly higher environmental exposure to heavy metals in recent times, their concentrations can be distinguished as a potential risk factor of CVDs.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from &lt;5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.

Survivability is a critical concern in WSNs, heavily influenced by energy efficiency. Addressing severe energy constraints in WSNs requires solutions that meet application goals while prolonging network life. This paper presents an energy optimization approach (EOAMRCL) for WSNs, integrating the Grey Wolf Optimization (GWO) for enhanced performance. EOAMRCL aims to enhance energy efficiency by selecting the optimal duty-cycle schedule, transmission power, and routing paths. The proposed approach employs a centralized strategy using a hierarchical network architecture. During the cluster formation phase, an objective function, augmented with GWO, determines the ideal cluster heads (CHs). The routing protocol then selects routes with minimal energy consumption for data transmission to CHs, using transmission power as a metric. In the transmission phase, the MAC layer forms a duty-cycle schedule based on cross-layer routing information, enabling nodes to switch between active and sleep modes according to their network allocation vectors (NAV). This process is further optimized by an enhanced CSMA/CA mechanism, which incorporates sleep/activate modes and pairing nodes to alternate between active and sleep states. This integration reduces collisions, improves channel assessment accuracy, and lowers energy consumption, thereby enhancing overall network performance. EOAMRCL was evaluated in a MATLAB environment, demonstrating superior performance compared to EEUC, DWEHC, and CGA-GWO protocols, particularly in terms of network lifetime and energy consumption. This highlights the effectiveness of integrating GWO and the updated CSMA/CA mechanism in achieving optimal energy efficiency and network performance.

This article examines the complex interactions of the multiplier effect within the realm of tourism, with a specific emphasis on national parks. The main objective is to evaluate the multiplier effect within national parks, specifically focusing on Buiratau State National Nature Park in Kazakh-stan as a case study. The multiplier effect is a fundamental principle in the field of economic analysis. Economic multiplier effect is the term used to describe the occurrence when an initial infusion of spending in a certain industry leads to subsequent rounds of extra and sustainable economic activity. In the context of national parks, this phenomenon arises when visitor expendi-tures result in several favorable consequences, including increased employment, infrastructure advancement, and general economic expansion. The article seeks to measure the multiplier effect of tourism activities in Buiratau State National Nature Park through a thorough assessment. This entails examining several variables and datasets pertaining to visitor expenditure and its influ-ence. The study contributes to the existing literature by examining a recently constructed national park in a developing country. It compares the findings of this park with well-established national parks in other areas, emphasizing the distinct problems and opportunities it presents. Further-more, the research presents a methodological framework for evaluating the multiplier effect of national parks, which may be utilized in comparable contexts. This research ultimately enhances our comprehension of the economic implications of national parks and emphasizes their function as drivers for local and regional growth.

Despite the effectiveness of insulin injections in managing hyperglycemia in Type 1 Diabetes, they fall short in addressing autoimmunity and regenerating damaged islets. This review aims to explore the potential of various treatment modalities for T1DM, including mesenchymal stem cells (MSCs), MSC-derived exosomes, gene therapy, islet allotransplantation, and pancreatic islet cell transplantation. Results: MSCs demonstrate efficacy in T1DM treatment through immunomodulation and tissue regeneration, although further research is warranted to optimize their therapeutic potential. Gene therapy presents a promising approach despite challenges such as donor shortage and immune rejection. Pancreatic islet cell transplantation emerges as a viable option, albeit with associated risks including graft rejection and the need for immunosuppression. Teplizumab, an FDA-approved humanized monoclonal antibody, revolutionizes the treatment landscape of Type 1 Diabetes by significantly delaying its onset, offering a paradigm shift since the discovery of insulin Conclusion: Ongoing studies and technological advancements in T1DM management offer a promising outlook for improved treatments and possibly even eradication on a global scale. MSCs, MSC-derived exosomes, gene therapy, and pancreatic islet transplantation hold considerable potential.

In our recent publications pertaining to 4G model of final unification and based on strong and electroweak interactions, we have developed a completely new formula for estimating nuclear binding energy. With reference to currently believed Semi Empirical Mass Formula (SEMF), we call our formula as ‘Strong and Electroweak Mass Formula’ (SEWMF). Our formula constitutes 4 simple terms and only one energy coefficient of magnitude 10.1 MeV. First term is a volume term, second term seems to be a representation of free nucleons associated with electroweak interaction, third term is a radial term and fourth one is an asymmetry term about the mean stable mass number. Considering this kind of approach, nuclear structure can be understood in terms of strong and weak interactions and cold nuclear fusion like complicated concepts can be understood in a theoretical approach positively. In this paper, by considering the accountability of we are making an attempt to improve the applicability and effectiveness of SEWMF. Number 0.00125 being a workable electroweak coefficient for Z=6 to 132 and A=2Z to 3.5Z, number of free nucleons assumed to be associated with electroweak interaction can be expressed as Improved asymmetry term can be expressed as, where represents the light house like stable mass number. With reference to old version, our improved binding energy formula can be expressed as, We are working on its possible modification for mass numbers less than the stable mass numbers. Following this approach, it is possible to show that nuclear binding energy scheme is associated with strong and weak interactions and is practically independent of Coulombic repulsions. Proceeding further, currently believed cold nuclear fusion assumed be associated with hydrated metals can be understood and can be confirmed with strong and weak interactions independent of coulombic repulsions. We are very confident to say that our approach will certainly motivate modern science community in this new direction.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

The literature study delves into novel therapeutic strategies in transplantation medicine, highlighting unique approaches that could revolutionize current practices. It emphasizes novel patterns that have the potential to transform the current landscape. Commencing with a thorough examination of the historical environment, it traces crucial advances and changes in transplantation. The focus is on traditional techniques, emphasizing their limitations and challenges. An extensive examination of contemporary transplantation therapies offers valuable insights into the most recent progress in organ, cellular, and tissue transplantation. This analysis examines the immunological obstacles and outlines the current advancements and constraints. The exploration further navigates into novel models and concepts such as immunomodulation, developments in organ preservation techniques, gene editing, biomaterials, scaffold-based solutions, and the integration of precision medicine, artificial intelligence, and machine learning applications. Each section analyzes the potential for change and current progress in various areas, backed by relevant scientific sources up to 2023. The subsequent sections delve into innovative cellular therapies, biotechnological progress, current clinical trials, and case studies demonstrating effective applications. This examination delves into the ethical and regulatory considerations of innovative therapeutic procedures, emphasizing ethical implications, regulatory frameworks, and the importance of balancing innovation with patient welfare. The literature review concludes by offering a forward-looking perspective, emphasizing potential progress, anticipated challenges, and advocating for collaboration and interdisciplinary approaches to overcome limitations in the field of transplantation medicine.

In this work, the nearest neighbor distances and Voronoi cell features of the Cu-Ag deposits were analyzed and fitted with Lognormal, Weibull, and Gamma distributions. The nearest neighbor distance distributions of the samples were compared with those of complete spatially random points, showing spatial inhomogenity due to the nucleation exclusion effect. The radial distribution function was calculated, showing both influences from the grain size and the nucleation exclusion effect. Voronoi cells were generated based on the shape of the grains. The size, occupancy, and coordination of the Voronoi cells were examined and fitted. The results show that despite the Cu-Ag deposits seem to be governed by instantaneous nucleation mode, the spatial distribution of the nuclei is more impacted by the nucleation exclusion effect than the Cu-only samples. This behavior is also justified by the grain size distribution generated with Voronoi cell size and occupancy distributions.

Background: In our recent publications pertaining to 4G model of final unification and based on strong and electroweak interactions, we have proposed the existence of a weak fermion of rest energy 585 GeV. Objective: To confirm the physical existence of the proposed 585 GeV weak fermion by analyzing weak and strong interactions in a unified approach via 4G model of final unification, super symmetry and string theory. Method: Considering the proposed nuclear charge of 2.95e, proton, electron mass ratio, specific charge ratios of proton and electron, Fermi’s weak coupling constant, Reduced Planck’s constant, nucleon magnetic moments, nuclear stability, nuclear binding energy, nuclear mass and neutron lifetime, it is planned to confirm the physical existence of the proposed 585 GeV weak fermion. Results: All proposed logics and formulae clearly establish the physical existence of 585 GeV weak fermion directly and indirectly. Conclusion: Believing in the physical existence of the proposed 585 GeV weak fermion, there is a scope for observing galactic TeV radiation coming by virtue of annihilation of 585 GeV fermions and radiation associated with various astrophysical acceleration mechanisms of 585 GeV fermions. Appeal: As we are beginners of astrophysics domain, we appeal the science community to see the possibility of considering the proposed 585 GeV weak fermion with a charge of $\pm\left(e\right)$ in place of electron and proton.

In this paper, we make an attempt to estimate the famous Avogadro number with programming logics written in Python associated with advanced nuclear binding energy formulae. Average rest mass of nucleon, nuclear binding energy per nucleon and electron rest mass seem to play a vital role in estimating the unified atomic mass unit and Avogadro number. Interesting point to be noted is that, Avogadro number seems to be the inverse of the Unified atomic mass unit. With further study, it seems possible to estimate the unified atomic mass unit and Avogadro number accurately. Our interesting observation is that, short range strong nuclear force seems to have a vital role in deciding the accuracy of Avogadro number. For that purpose one may consider AI techniques along with newly observed atomic nuclides and their nuclear binding energies. For Z=6 to 118 and A_low=2Z and A_upper=3.5Z, estimated average value of Avogadro number is $N_{Average} \cong 6.01938 \times 10 ^{26}$. Considering the saturation of nuclear binding energy, at Z=26, $N_{Z=26} \cong \left(6.02229 \textrm{to} 6.02285\right) \times 10 ^{26}$. At academic level, our proposal can be given a chance as a case study. It is planned to develop a web application for this purpose.

In this study, the olive pomace was considered because of its importance in the environment. So, this study carried out to estimate the total nitrogen content and the fatty acids profile of olive pomace. The olive pomace samples were collected from Irbid, Jarash, Ajloun and Mafraq during the harvesting season 2014 to study the biochemical characteristics of fatty acid composition and the total nitrogen (TN) content. The total nitrogen content was determined by standard Kjeldahl method and the fatty acid profile was detected by gas chromatography (GC). The results show that the total nitrogen content ranged from (0.39 ± 0.0) to (0.62 ± 0.02) with statistically significant difference suggesting that the composition of matrices and their percentage may be responsible for composition of amendments. The calculated total protein percentage ranged between (2.43 ± 0.00) to (3.87 ± 0.17). Also, 13 different fatty acids were quantitatively profiled and quantitated. Oleic acid (C 18:1) was found to be the highest percentage of all other fatty acids and ranged between (59.03%) and (63.81%), moreover the C 18:1/C 18:2 (oil quality) was calculated and C.V% showed variation meaning that nutritional implication could affect the oxidative stability of oils. In conclusion, OP by-product could give a sustainable and alternative-cheap source for fertilizers, pharmaceutical industries, cosmetics and other industries.

Organic electrophoretic coatings have gained significant attention due to their ability to provide a uniform and controlled coating thickness, high coating adhesion, and excellent corrosion protection properties. In this work, to investigate the aging behaviors of an organic electrophoretic coating for magnesium alloys, water absorption kinetics curves of the coatings after immersion in 3.5 wt.% NaCl at 20℃ and 40℃ were measured, and parameters such as the saturated water absorption and saturation time of the free film coatings were fitted to determine the densification evolution of the organic coatings. A tensile test was used to test the tensile strength of the organic coating during service to determine the evolution of the strength and toughness of the organic coating. The evolution of wet adhesion of organic coatings with service time was tested by ASTM D4541-02. The impedance spectra of the organic coatings under the above conditions were detected by EIS, and finally, the failure behavior of the organic coatings under immersion was analyzed.