One way to reduce the negative impact of human activity on the natural environment is to use natural, easily available and relatively cheap to produce compounds in industrial processes. One such compound is naturally occurring calcium carbonate (CaCO3). This compound has adsorption properties so that it can be an alternative to commonly used adsorbents. The aim of this work is to determine the possibility of using CaCO3 to remove pharmaceutical substances such as sulfadiazine and tetracycline from water. The CaCO3 used in this work was synthesised using our own method, which allows the production of CaCO3 particles with nanometric size. In the conducted research, calcium carbonate was used in the form of a suspension in purified solutions and as an inorganic filling of the developed membranes. The mass of pharmaceutical substances removed from their aqueous solutions was determined in the tests carried out. Based on the results obtained, it can be concluded that CaCO3 has the ability to adsorb both tetracycline and sulfadiazine. In suspension tests, the mass of the removed substances per unit mass of adsorbent was 1.52 mg/g and 6.85 mg/g, respectively. In turn, in the case of the process using the developed membranes, the mass of the removed substances per unit mass of adsorbent was 232 mg/m2 and 524 mg/g, which is a several times greater increase in the mass of the removed substance compared to the process using an unmodified membrane.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

While the language model using the stop sign as an independent token has been widely used to decide when the model should stop, it may lead to the growth of vocabulary dimensions and further problems. Similarly, present research on game algorithms usually estimate stopping point related problems based on the evaluation of the winning rate. However, information redundancy may also exist in such models, thus increasing the training difficulty. Above two types of tasks (and similar autoregressive tasks) show a common problem of stopping point prediction. In this paper, we describe a design of separated model, trying to separate the complexity of stopping point prediction from the main task model, so that the information used for estimating stopping point can be reduced. On this basis, in order to verify the rationality of using separated model, we propose a model-free test method. It judges the separability of transformed data based on point difference and sequence difference metrics. In this way, it can predict the credibility of the separated model inference.

Lactoperoxidase system (LPS) effect on quality of raw and pasteurized milk under real conditions along the dairy value chain in Ethiopia was evaluated. A total of 250 milk samples were collected from farmers, collectors, and factories. Experimental samples were LPS-activated of morning and overnight milk. The samples were tested with several chemical and microbiological tests such as total bacterial count (TBC), total coliform count (TCC) and Escherichia coli count (EC). Results indicated that all LPS-activated milk samples had a higher quality than all the control samples. For instance, both the morning and overnight farm milk samples had a mean TBCs of 5.79 log and 6.55 log cfu/ml which is significantly (p

Reservoirs created by damming rivers significantly modify the environment and problems may arise: the storage of nutrients and organic matter in reservoirs often leads to decreased water quality due to eutrophication. Reservoirs built on lowland rivers are exposed to significant nutrient loads, often leading to eutrophication. In this article, the Sulejów Reservoir, in Central Poland, was the subject of the research, which focused on the use of Sentinel-2 remote sensing data to detect phytoplankton blooms, and on understanding the pattern of wind-driven surface currents using the CCHE2D model (a depth-averaged hydrodynamic model). The calculation of the total phosphorus load has shown that the reservoir mainly acts as nutrient storage. Still, during the low flow and intensive phytoplankton bloom, it can be a source of nutrients. The distribution of phytoplankton bloom on the Sulejów Reservoir was documented using eight Sentinel-2 satellite images from the vegetation season of 2020 and the Normalized Difference Chlorophyll Index (NDCl). Coupling remote sensing data and numerical modelling helps to interpret the hydrodynamic model results and understand nutrients and sediment dynamics within the reservoir. Hydrodynamic modelling combined with remote sensing data can be a valuable tool for selecting appropriate locations for water quality measurements at monitoring stations.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

This pandemic of COVID-19 is tedious to control. The only lockdown is the way to stop the spread of this infection. Conventional health care is facing a real challenge to operate. Primarily the challenge is to provide health care support for COVID-19 patients with limited resources and continue the health care services like earlier.Perhaps, this challenge is the same but magnitude is different from different geographical locations around the globe. In this article, we presented a Bayesian algorithm with the Code to predict cancer death due to COVID-19. This code is possible to run at different time points and different geographical locations around the world. This code will help us to get the best strategy and shift the treatment option for cancer treatment. The model would provide physicians with an objective tool for counseling and decision making at different hotspots and small areas to implement.

Extraction techniques of important bioactive molecules from the major concern of Seafood byproducts are getting emphasis for better valorization. Employing green extraction technologies for efficient and quality production of these bioactive molecules is also strictly required. Hence, understanding the extraction process parameters to effectively design an applicable optimization strategy could make this real. In this review, statistical optimization strategies applied for the extraction process parameters of bioactive molecules from Seafood byproducts are focused. The type of experimental designs, and techniques applied to criticize and validate the effects of independent variables on the extraction output was addressed. Dominant parameters studied were enzyme/substrate ratio, pH, time, temperature and power of extraction instruments. The yield of bioactive compounds, chitin and chitosan, proteins and peptides, enzymes and carotenoids (Astaxanthins) were the most studied responses. Efficiency and/or economic and quality considerations and their selected optimization strategies that favour the production of potential bioactive molecules were also reviewed.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

This paper studies single change-point detection in the volatility of a class of parametric conditional heteroscedastic autoregressive nonlinear (CHARN) models. The conditional least-squares (CLS) estimators of the parameters are defined and are proved to be consistent. A Kolmogorov-Smirnov type-test for change-point detection is constructed and its null distribution is provided. An estimator of the change-point location is defined. Its consistency and its limiting distribution are studied in detail. A simulation experiment is carried out to assess the performance of the results which are also applied to two sets of real data.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

The article presents the results of cyanide leaching of gold-containing concentrate using the trichlorocyanuric acid (TCCA) oxidizer. Gold-containing concentrate obtained from a gold tailings sample from a gold recovery factory (GRF) in one of the deposits of Kazakhstan that was not previously studied for concentrability. According to X-ray phase analysis and energy dispersive spectrometry (DSM) data, the main compounds in the tailings sample under study are: pyrite FeS2, quartz SiO2, calcite CaCO3, albite NaAlSi3O8, muscovite KAl2Si3AlO10(OH)8, dolomite CaMg(CO3)2, and oxidized iron compounds. Microscopic studies have established the presence of gold grains in free form, ranging in size from 0.9-10.2 mkm Au-ultrafine and fine gold. Obtaining a gold-containg concentrate with a gold content of 15.95 g / t is possible according to the enrichment scheme, which includes centrifugal separation, classification according to the fineness class -0.05 mm, additional grinding of hydrocyclone sands to a fineness of 90.0-95.0% of the class finer than 0.050 mm, and control centrifugal separation. Since pyrite in technogenic raw materials is the main gold-containing mineral, this paper presents studies on the oxidizability of pyrite with the TCCA oxidizer. The results of studies on the oxidation of pyrite using the TCCA oxidizer show that the products of its hydrolysis oxidize pyrite with the formation of various iron compounds on its surface. Pretreatment of gold-containing concentrate with oxidizer TCCA for 3 hours before the cyanidation process (20 hours) allows to increase the recovery of gold in the solution by 5.8 %.

The Food and Drug Administration’s 2011 Process Validation Guidance and International Council for Harmonization Quality Guidelines recommend continued process verification (CPV) as a mandatory requirement for pharmaceutical, biopharmaceutical, and other regulated industries. As a part of product life cycle management, after process characterization in stage 1 and process qualification and validation in stage-2, CPV is performed as stage-3 validation during commercial manufacturing. CPV ensures that the process continues to remain within a validated state. CPV requires the collection and analysis of data related to critical quality attributes, critical material attributes, and critical process parameters on a minimum basis. Data is then used to elucidate process control regarding the capability to meet predefined specifications and stability via statistical process control tools. In statistical process control, control charts and Nelson rules are commonly used throughout the industry to monitor and trend data to ensure that a process remains in control. In the control chart, the mean value is taken as the center line, and 3σ limits are placed on either side of the center line. In CPV, manufactured lots are summarized, trended, and discussed at a cross-functional level at pre-defined intervals (either weekly, bi-weekly, or even monthly) based on the batch run rate. A cross-functional team assesses details regarding 1) violation frequency, 2) statistical strength of the signal, 3) violation magnitude and its impact on process or quality, and 4) any potential root causes for out-of-expectation or out-of-trend signals. The cross-functional team must analyze whether any signal identified by the control chart is reliable and must determine whether corrective action should be taken and justify the decision in the CPV meeting minutes based on statistical strength and reliability of the signal. However, basic control charts are susceptible to false alarms and nuisance alarms. Therefore, it is imperative to understand the assumptions behind control charts and the inherent false alarm rates for different Nelson rules. In this article, the authors have detailed the assumptions behind the usage of control charts, the rate of false alarms for different Nelson rules, the impact of skewness and kurtosis of a data distribution on the false alarm rate, and methods for optimizing control chart design by reducing false alarm rates and nuisance signals.

We present an any-to-one voice conversion (VC) system, using an autoregressive model and LPCNet vocoder, aimed to enhance the converted speech in terms of naturalness, intelligibility, and speaker similarity. As the name implies, non-parallel any-to-one voice conversion does not require paired source and target speeches and can be employed for arbitrary speech conversion tasks. Recent advancements in neural-based vocoders, such as WaveNet, have improved the efficiency of speech synthesis. However, in practice, we find that the trajectory of some generated waveforms is not consistently smooth, leading to occasional voice errors. To address this issue, we propose to use an autoregressive (AR) conversion model along with the high-fidelity LPCNet vocoder. This combination not only solves the problems of waveform fluidity but also produces more natural and clear speech, with the added capability of real-time speech generation. To precisely represent the linguistic content of a given utterance, we use speaker-independent PPG features (SI-PPG) computed from an automatic speech recognition (ASR) model trained on a multi-speaker corpus. Next, a conversion model maps the SI-PPG to the acoustic representations used as input features for the LPCNet. The proposed autoregressive structure enables our system to produce the following prediction step outputs from the acoustic features predicted in the previous step. We evaluate the effectiveness of our system by performing any-to-one conversion pairs between native English speakers. Experimental results show that the proposed method outperforms state-of-the-art systems, producing higher speech quality and greater speaker similarity.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

Global models have been developed to tackle the challenge of forecasting sets of series that are related or share similarities, but not for heterogeneous datasets. Various methods of partitioning by relatedness have been introduced to enhance the similarities of the set, resulting in improved forecasting accuracy but often at the cost of a reduced sample size, which could be harmful. To shed light on how the relatedness between series impacts the effectiveness of global models in real-world demand forecasting problems we perform an extensive empirical study using the M5 competition dataset. We examined cross-learning scenarios driven by the product hierarchy commonly employed in retail planning, which allow global models to capture interdependencies across products and regions more effectively. Our findings show that global models outperform state-of-the-art local benchmarks by a considerable margin, indicating that they are not inherently more limited than local models and can handle unrelated time series data effectively. The accuracy of data partitioning approaches increases, as the size of the data pools and the models' complexity decrease. However, there is a trade-off between data availability and data relatedness. Smaller data pools lead to increased similarity among time series, making it easier to capture cross-product and cross-region dependencies, but this comes at the cost of a reduced sample, which may not be beneficial. Finally, it's worth noting that the successful implementation of global models for heterogeneous datasets can significantly impact forecasting practice.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

In most econometrics literature, the Autoregressive Distributed Lag (ARDL) model is often applied in many economic analyses to study short and long run relationships. This is because ARDL model can deal with economic variables that are integrated of different order (I(0), I(1) or combination of both) and also it is robust where there is single long-run relationship between the underlying variables in a simple sample size. This study applied the ARDL model to examine the contributions of commercial Banks to GDP growth in Nigeria. To achieve this, annual data covering 1981 to 2015 for loans and advances, savings, lending rates and GDP of Financial Institutions were collected from CBN bulletin. The ADF test revealed that the variables are I(1) except for lending rate which was of I(0) order. The ARDL(1,1,1,2) model revealed that loans and advances, and lending rates are significantly positively related to GDP in Nigeria but savings was not significant in the model. The model revealed some evidence of short run relationships while the ecm(-1) was -0.6156 (P-value=0.0038<0.05) which means that the rate of the speed of adjustment to equilibrium is 61.56% annually. The estimated model is free from serial correlation, multicollinearity, heteroscedasticity while the model is stable and the residuals are normally distributed. The study recommends that savings and savings culture should be encouraged in Nigeria since economic theory states that savings and investment are related in any economic development.

A multimodal detection system with complementary capabilities for efficient detection was developed for impurity detection. The system consisted of a visible light camera, a multispectral camera, image correction and registration algorithms. It can obtain spectral feature and color feature at the same time, and has higher spatial resolution than a single spectral camera. This system was applied to detect impurities in Pu ’er tea to verify its high efficiency. The spectral and color features of each pixel in the images of Pu ’er tea were obtained by this system and used for pixel classification. The experimental results show that the accuracy of Support Vector Machine (SVM) model based on combined features is 93%, which is 7% higher than that based on only spectral features. By applying median filtering algorithm and contour detection algorithm to the label matrix extracted from pixel-classified images, 8 impurities except hair were detected successfully. Moreover, taking advantage of the high resolution of visible light camera, small impurities can be clearly imaged. By comparing the segmented color image with the pixel-classified image, small impurities such as hair could be detected successfully. Finally, it is proved that the system can obtain multiple images to allow a more detailed and comprehensive understanding of the detected items, and has excellent ability to detect small impurities.

Micellar Casein Concentrate (MCC) is manufactured from microfiltration (MF) of skim milk utilizing ceramic or polymeric membrane filtration. While ceramic filtration has higher efficiency, use of polymeric is cost effective and the process is familiar to several US dairy processors. The aim of the present study was to develop an optimized membrane filtration process to produce MCC using spiral wound polymeric membrane filtration (SW MF) system by systematic selection of transmembrane pressure (TMP) and level of diafiltration (DF). Using skim milk as feed material, preliminary lab-scale MF experiments were conducted using 0.5 µm polyvinylidene fluoride (PVDF) membrane. Three TMP (34.5, 62.1, and 103.4 kPa) and three levels of DF (70, 100, and 150%) along with a process without DF as control were used in the study. Effect of TMP and effectiveness of DF on flux rates, SP removal, casein to total protein (CN/TKN) ratio, casein to true protein (CN/TP) ratio, rejection of casein (rej CN) and SP (rej SP) were evaluated. At all TMP values used in the study, the overall flux (O Flux) increased with the level of DF. Highest O Flux of 30.77 liter per meter square per hour (LMH) was obtained with 34.5 kPa pressure and 150% DF. The impact of DF was more pronounced at lower pressures than at the higher pressures used in the study. With controlled DF, instantaneous flux was maintained within 80% of initial flux for the entire process run. For all the experiments, casein has a rejection of 0.97 to 1.0, while serum protein has the lowest rejection of 0.10 at 34.5 kPa pressure and 150% DF level. Use of 34.5 kPa and DF level of 150 % contributed to 81.45% SP removal, and casein to true protein ratio of 0.96. SP removal data from the lab-scale experiments were fitted into a mathematical model using DF and square of TMP as factors. The model predicts SP removal within 90-95% of actual SP removal got from the pilot plant experiments.

Any effort to combat corruption can benefit from an examination of past and projected worldwide trends. In this paper, we forecast the level of corruption in countries by integrating an artificial neural network modeling and time series analysis. The data were obtained from 113 countries from 2007 to 2017. The study is carried out at two levels: (a) global level where all countries are considered as a monolithic group; and (b) cluster level, where countries are placed into groups based on their development-related attributes. For each cluster, we use the findings from our previous study on the cluster analysis of global corruption using machine learning methods that identified the four most influential corruption factors, and we use those as independent variables. Then, using the identified influential factors, we forecast the level of corruption in each cluster using a nonlinear autoregressive recurrent neural network with exogenous inputs (NARX), an artificial neural network technique. The NARX models were developed for each cluster, with the objective function in terms of the Corruption Perceptions Index (CPI). For each model, the optimal neural network is determined by finetuning the hyperparameters. The analysis was repeated for all countries as a single group. The accuracy of the models is assessed by comparing the mean square errors (MSE) of the time series models. The results suggest that the NARX artificial neural network technique yields reliable future values of CPI globally or for each cluster of countries. This can assist policymakers and organizations in assessing the expected efficacies of their current or future corruption control policies from a global perspective as well as for groups of countries.

Research background: Relationship between inflation rate, unemployment rate, interest rate and real gross domestic product per capita in Nigeria. However, there seems to be a short-run or long-run relationship among the macroeconomic variables.Purpose: This study investigated the impact of the inflation rate, unemployment rate and interest rate on real gross domestic product per capita (RGDPPC) (proxy for economic growth) and proffered recommendations towards enhancing economic growth and to reduce the distasteful effects of inflation rate, unemployment rate and interest rate in Nigeria in this present time economic challenges.Research methodology: This study applied a linear dynamic model Autoregressive Distributed Lag (ARDL) modeling technique to analyze the short-run dynamics and long-run relationship of the economic growth in Nigeria over the sample period between 1984 and 2017 using annual secondary data extracted from World Bank Development Indicators Report (last updated January 2019).Results: The empirical results showed that there was long-run relationship between inflation rate, unemployment rate and interest rate on real gross domestic product per capita (proxy for economic growth) in Nigeria. The result further revealed that only unemployment rate had a significant positive impact on real gross domestic product per capita in the long-run and inflation rate had a significant negative impact on real gross domestic product per capita in the short-run.Novelty: Therefore, the study concluded that unemployment rate and inflation rate proved to have significant impacts on economic growth in the long-run and short-run respectively. Formulation of policies to reduce unemployment through the adoption of labour concentrated technique of production, entrepreneurship development and policy to keep the inflation rate at single digit.

This study investigates why young adults live with their parents in Sweden. As young adults’ living arrangements affect decisions about marriage, education, childbirth, and participation in the workforce, more knowledge for policy makers is crucial to implementing effective policies to support young adults and promote financial independence and well-being. Using a data set from 1998 to 2021 at the municipal level in Sweden, we used a spatial autoregressive panel data model to examine the proportion of young adults living at home and regional disparities. The study uncovers intraregional variations, illustrating how different municipalities within Sweden exhibit different patterns of young adults living at home. Our findings reveal that economic factors, such as unemployment, significantly impact this pattern. The dynamics of the housing market, demographic factors, cultural differences, and location-specific characteristics also play an essential role in explaining this pattern. The findings suggest that the key drivers are the lack of rental housing, high unemployment rates, a high degree of urbanisation, interregional migration, and lack of social capital.

While there are software tools available for assisting to conduct the Life Cycle Assessment (LCA), such as OpenLCA, these tools lack integration with process design, simulation and optimization software. As LCA has critical role in sustainable product design, it is presented in this work a platform called EMSO_OLCA, which integrates the LCA provided by OpenLCA into the Environment for Modeling, Simulation, and Optimization (EMSO). EMSO_OLCA incorporates a database of environmental impact assessment methodologies from OpenLCA and aligns to the principles of LCA outlined in ISO 14040 and ISO 14044. Validation tests were conducted to compare the results obtained by the LCA of sugarcane ethanol using OpenLCA and EMSO_OLCA, revealing a high level of agreement. The average relative error was 0.045%, indicating a negligible discrepancy between the tools. Besides, it took only 0.3 seconds for calculation, which is desirable for using with process systems engineering tools. A second case study was applied to a steam and bioelectricity production from the combustion of sugarcane bagasse and straw in a combined heat and power system. The results show the integration of LCA with simulation and sensitivity analysis tools, thus contributing for supporting sustainable decision-making processes. EMSO_OLCA bridges the gap between LCA and process engineering, enabling a holistic approach to sustainability, design and implementation of environmentally friendly solutions.

Although composting has many advantages in the treatment of organic waste, there are still many problems and challenges associated with emissions, like NH3, VOCs, and H2S, as well as greenhouse gases such as CO2, CH4, and N2O. One promising approach to enhancing composting conditions is used of novel analytical methods bad on artificial intelligence. To predict and optimize the emissions (CO, CO2, H2S, NH3) during composting process kinetics thought mathematical models (MM) and machine learning (ML) models were utilized. Data about everyday emissions from laboratory composting with compost’s biochar with different incubation (50, 60, 70 °C) and biochar doses (0, 3, 6, 9, 12, 15% d.m.) were used for MM and ML models selections and training. MM has not been very effective in predicting emissions, (R2 0.1 - 0.9), while ML models such as acritical neural network (ANN, Bayesian Regularized Neural Network; R2 accuracy CO:0,71, CO2:0,81, NH3:0,95, H2S:0,72)) and decision tree (DT, RPART; R2 accuracy CO:0,693, CO2:0,80, NH3:0,93, H2S:0,65) have demonstrated satisfactory results. For the first time the ML models to predict CO and H2S during composting were demonstrated. Further research in a semi-scale and field study composting with biochar is needed to improve the accuracy of developments models.

The research work examined the trend of HIV/AIDS, Tuberculosis, and Hepatitis diseases in Plateau state. Annual data from 2003 to 2018 was collected from the department of biostatistics at Plateau State Specialist Hospital (PSSH), Jos. The methods of analysis used are the Poisson Autoregressive Model (PAR(1)) and the Poisson Exponentially Weighted Moving Average Model (PEWMA). The results revealed a significant annual decrease of 23.9% and 4% in Tuberculosis and HIV/AIDS respectively. Furthermore, the results showed a significant annual increase of 46% in Hepatitis. The PEWMA model used revealed that TB increased by 0.02% when there is an increase in HIV but not significant, while Hepatitis significantly aggravates TB by at least 0.24%. Also, there is a significant rise in HIV by 0.85% when TB increases but Hepatitis has no such effect on HIV. Lastly, PEWMA model indicated a rise of 0.5% in Hepatitis cases when there is an increase in TB, but a surge in HIV has no such effect on Hepatitis cases in Jos. The study recommended that fight against TB should be intensified since TB cases significantly affect both HIV and Hepatitis in Jos, Nigeria.

In a dynamic production processes, mechanical degradation poses a significant challenge, impacting product quality and process efficiency. This paper explores a novel approach for monitoring degradation in the context of viscose fiber production, a highly dynamic manufacturing process. Using causal discovery techniques, our method allows domain experts to incorporate background knowledge into the creation of causal graphs. Further, it enhances the interpretability and increases the ability to identify potential problems via changes in causal relations over time. The case study employs a comprehensive analysis of the viscose fiber production process within a prominent textile industry, emphasizing the advantages of causal discovery for monitoring degradation. The results are compared with state-of-the-art methods, which are not considered to be interpretable, specifically LSTM-based autoencoders, showcasing the alignment and validation of our approach. This paper provides valuable information on degradation monitoring strategies, demonstrating the efficacy of causal discovery in dynamic manufacturing environments. The findings contribute to the evolving landscape of process optimization and quality control.

As an export commodity coffee industry contributes to the economies of both exporting and importing countries. The aim of the study involves competitiveness and determinant of coffee export in Ethiopia through the period of 1990–2018 observations. To explain the level of comparative advantage and competitiveness respectively Revealed Comparative Advantage and Syematric Revealed Comparative Advantage were employed. To capture determinans of coffee ARDL model with bound testing to co-integration approach was employed to investigate the long-run association between Ethiopian total coffee export in bags (60kg each) with domestic coffee production, world coffee price, real exchange rate, FDI, world coffee production and price ratio. Even though Ethiopia has the comparative advantage in the export of coffee, however, the share it in the international market low in amount and not inlined with RCA. Bound testing to co-integration approach result confirmed the existence of a long-run relationship between total coffee exports of Ethiopia with its independent variables. The analysis pointed out that in the long run the extent of domestic coffee production, world price, and real exchange rate positively and significantly affects total coffee export. However, FDI, price ratio, world production of coffee have negative & significant effects. In the short-run Ethiopian total coffee export defined as a positive significant function of domestic coffee production and real exchange rate positive but insignificant effect with Level of RCA and world price as well as a negative function of FDI, price ratio, and world production of coffee. Coefficient Error Correction Model (ECM (-1)) was negative and significant with a value of 134.4 % of the adjustment would make each year and return to its long-run equilibrium after 1.3 years. The policy implication calls for addressing issues of the combined effect of the policy setting, institutions, and market failures to avoid the evil effect of the sector.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

This paper describes the state of the art and future opportunities for process design and sustainable development. In the Introduction the main global megatrends and European Union's response to two of them, the European Green Deal, are presented. The organization of professionals in the field, their conferences and publications support the two topics. A brief analysis of the published documents in the two most popular databases shows that the environmental dimension predominates, followed by an economic one, while the social pillar of sustainable development is undervalued. The main design tools for sustainability are described. As an important practical case, the European chemical and process industries are analyzed and their achievements in sustainable development are highlighted; in particular, their strategies are presented in more detail. The conclusions cover the most urgent future development areas of the process industries, carbon capture with utilization or storage, process analysis, simulation, synthesis and optimization tools; zero waste, circular economy and resource efficiency already play an important role. However, more profound changes are needed in the coming decades, including a shift away from growth with changes in habits, lifestyles and business models. Lifelong education for sustainable development will play a very important role in the growth of democracy and happiness instead of consumerism and neoliberalism.

Predictive maintenance (PM) algorithms are widely applied for detecting operational anomalies on industrial processes to trigger maintenance before a possible breakdown; however, much less focus has been devoted to the use of such PM predictions as feedback in automated process control mechanisms. They usually integrate preventive solutions to protect the machines, usually causing downtimes. The premise of this study is to develop a holistic adaptive process scheduling mechanism that incorporates PM analysis as a safety component to optimize the operation mode of an industrial process toward preventing breakdowns while maintaining its availability and operational state, thereby reducing downtimes. As PM is largely a data-driven approach; hence, relies on the setup, we first compare different PM approaches and identify a one-class support vector machine (OCSVM) as the best performing option for the anomaly detection on our setup. Then, we propose a novel pipeline to integrate maintenance predictions into a real-time adaptive process scheduling mechanism. It schedules for the most suitable operation, i.e., optimizing for machine health and process efficiency, according to the abnormal readings. To demonstrate the pipeline on action, we implement our approach on a small-scale conveyor belt system utilizing our Internet of Things (IoT) framework. The results show that our PM-based adaptive process control provides an efficient process with less or no downtime. We also conclude that a PM approach does not provide sufficient efficiency without its integration into an autonomous planning process.

This study addresses the challenge of treating skin cancer effectively, especially in visible areas like the face, where traditional methods may be undesirable. Current options, including surgery and radiation therapy, have limitations such as complexity, expense, and imprecise dose delivery. The proposed solution involves additively manufacturing personalized patches using diagnostic imaging data, offering a targeted and controlled dose of beta-emitting isotopes like Y-90. The patches, tailored to the tumor's shape and depth, aim to minimize damage to healthy tissues and structures. Through 3D printing technology we demonstrated the feasibility of creating individualized applicators filled with radioisotopes, that have the potential to deliver therapeutic doses while ensuring patient comfort and affordability. This innovative approach, based on radiation delivery simulations, offers a promising future alternative to conventional radiation therapy methods. Clinical trials are required to validate its efficacy and safety, but the potential for reduced radiation exposure and enhanced treatment precision positions this personalized and targeted therapy as a valuable advancement in skin cancer treatment.

Rapid climate change requires more powerful and precise modeling methods to forecast future climate variability. The GSTARIMA Model is efficient, combining space-time analysis with the Autoregressive Moving Average (ARIMA) Model. The integration of heteroscedasticity error and the Kriging method can strengthen the Model's ability to handle the problem of non-constant error variance in the GSTARIMA Model and forecast at unobserved locations of climate observations. This paper's Systematics Literature Review (SLR) is presented comprehensively with the principal aim of developing a thorough understanding of applying the GSTARIMA Model with heteroskedasticity error and the Kriging Method in climate forecasting following the Data Analytics Lifecycle methodology. The Systematic Literature Review (SLR) process consists of three main stages. We sourced the articles from databases such as Scopus, Dimensions, and EBSCO-Host The subsequent stage involved conducting a comprehensive literature review using the PRISMA method to ensure rigor and depth. Additionally, we performed bibliometric analysis to enhance rigor. Lastly, we conducted a gap analysis session to scrutinize existing research on the GSTARIMA Model and identify new opportunities. This literature review reveals that integrating GSTARIMA Model with heteroscedasticity errors and the Kriging method is suitable for climate forecasting. This research inspires researchers to contribute to the improvement and refinement of the Model, making it a more potent and valuable tool in climate forecasting.

Water resource is considered as a significant factor in development of regional environment and society. Water consumption prediction can provide important decision basis for the regional water supply scheduling optimisations. According to the periodicity and randomness nature of the daily water consumption data, a Markov modified autoregressive moving average (ARIMA) model is proposed in this study. The proposed model, combined with the Markov chain, can correct the prediction error, reduce the continuous superposition of prediction error, and improve the prediction accuracy of future daily water consumption data. The daily water consumption data of different monitoring points are used to verify the effectiveness of the model, and the future water consumption is predicted, in the study area. The results show that the proposed algorithm can effectively reduce the prediction error compared to the ARIMA.

The time’s arrow of macroscopic physical phenomenon is reflected by irreversible physical process, which essentially occurs from small probability state to high probability state. In this paper, simplified models are proposed to understand the macroscopic physical process. In order to describe the information of a physical system, we defined the full self-information as "information height" to describe the complexity or difficulty of a macrostate of physical system. In this way, the direction of macroscopic physical process is from high information height to low information height. We can judge the direction of physical process by the information height. If we want the macroscopic physical process to evolve from the low information height state to the high information height state, the system need to add extra information and corresponding energy to increase the information height.

This research investigates the impact of oil price fluctuations on food prices in Saudi Arabia between 1979 and 2020 using Nonlinear Autoregressive Distributed Lags (NARDL) methodology. The study employs Augmented Dickey-Fuller (ADF) and Phillip Perron (PP) tests to determine the integration order of the variables and Bounds testing to confirm the existence of long-run cointegration relationships between each variable. The results indicate that oil shocks influence food prices through several mechanisms. Firstly, the cost of energy increases due to the rise in oil prices, affecting the agricultural commodity market, including farm equipment, food processing, packaging, and distribution costs. Secondly, the demand for agricultural commodities to produce biofuels affects food availability and, thus, food prices. Thirdly, as an oil-based economy, the oil price shock affects food prices through its impact on government spending, which affects aggregate demand and liquidity. Therefore, Saudi Arabia should adopt appropriate policies to mitigate the impact of oil price shocks on food prices, including investing in renewable energy sources, diversifying its economy, and improving food production and supply chain efficiency. Additionally, implementing appropriate fiscal policies to ensure sufficient budget allocation for food support programs is crucial. However, investing in groundwater exploration can contribute significantly to the development of Saudi agriculture and to gradually achieving food self-sufficiency.

The hourly and daily rainfall data which is spatially distributed are required as an input for run-off rain model. Furthermore, the run-off rain model is used to detect early flooding. The daily and hourly rainfall data have characteristics that most of data are zero. Therefore we need a model which can capture the phenomenon. A time series model involving location, which is a model that can be developed to approach the daily and hourly rainfall data, we can call Vector Autoregressive (VAR) model. The VAR model allows us for modeling rainfall data in several areas. However, in certain conditions the VAR model often occurs over-parameterization and reduces degrees of freedom. The aim of this study is to compare the VAR model with Maximum Likelihood Estimator (MLE) and Bayesian to hourly and daily rainfall data in SampeanWatershed of Bondowoso. The results showed that the hourly and daily rainfall data are fitted to VAR process of orde 5 and 1 respectively. Based on the AIC and SBC values indicate that the Bayesian is better than the MLE method. The Bayesian is able to predict parameters by producing a smaller variance covariance matrix than the MLE.

.(1) Background: Groundwater resources management in dry lands, characterized by climate var-iability and population growth, is difficult. Exploration and exploitation of groundwater, due to inadequate surface water is very costly. The present study employed Analytic Hierarchy Process (AHP) and GIS to identify Ground-Water Potential (GWP) areas in a semi-arid region of Nigeria; (2) Methods: Land-use-land-cover, drainage density, slope, rainfall, static water level, soil media, vadose media and aquifer media were selected for GWP analysis. Parameters weights were de-termined using AHP and ranked based on their contribution to GWP by experts. The parameters were then integrated using weighted overlay tool in ArcGIS 10.5 to produce GWP map of the study area. Boreholes yield data from 245 wells were collected to determine the model accuracy and model validation; (3) Results: Results classified the study area into very high GWP (1.9%), high GWP (8.8%), moderate GWP (62%), low GWP (20.70%) and very low GWP (6.6%). Validation of the AHP model with boreholes yield data shows a correlation coefficient of 71.3% giving a good prediction; (4) Conclusions: AHP and GIS can be used to successfully map GWP areas which could serve as an exploration guide for sustainable management of groundwater resources in semi-arid areas.

The paper describes a model of subjective goal-oriented semantics extending standard "view-from-nowhere" approach. Generalization is achieved by using a spherical vector structure essentially supplementing the classical bit with circular dimension, organizing contexts according to their subjective causal ordering. This structure, known in quantum theory as qubit, is shown to be universal representation of contextual-situated meaning at the core of human cognition. Subjective semantic dimension, inferred from fundamental oscillation dynamics, is discretized to six process-stage prototypes expressed in common language. Predicted process-semantic map of natural language terms is confirmed by the open-source word2vec data.

Atmospheric correction is the processes of converting radiance measured at a spectral 1 sensor to the reflectance of the materials in a multispectral or hyperspectral image. This is an 2 important step for detecting or identifying the materials present in the pixel spectra. We present 3 two machine learning models for atmospheric correction trained and tested on 100,000 batches of 40 4 reflectance spectra converted to radiance using MODTRAN, so the machine learning model learns 5 the radiative transfer physics from MODTRAN. We created a theoretically interpretable Bayesian 6 Gaussian process model and a deep learning autoencoder treating the atmosphere as noise. We 7 compare both methods for estimating gain in the correction model to the well-know QUAC method 8 of assuming a constant mean endmember reflectance. Prediction of reflectance using the Gaussian 9 process model outperforms the other methods in terms of both accuracy and reliability.

The automation of welding processes requires the use of automated systems and equipment, in many cases industrial robotic systems, to carry out welding processes that previously required human intervention. Automation in the industry offers numerous advantages, such as increased efficiency and productivity, cost reduction, improved product quality, increased flexibility and safety, and greater adaptability of companies to market changes. The field of welding automation is currently undergoing a period of profound changes due to a combination of technological, regulatory, and economic factors worldwide. Nowadays, the most relevant aspect of the welding industry is to meet customer requirements by satisfying their needs. To achieve this, the automation of the welding process through sensors and control algorithms ensures the quality of the parts and prevents errors such as porosity, unfused areas, deformations, excessive heat, etc. This paper proposes an intelligent and adaptive system based on the measurement of welding joints using laser scanning and the subsequent analysis of the obtained point cloud to adapt the welding trajectories.

There are many pollution and environment problem in the human ecosystem. There are different methods are used to removal of sulfur from sour gases for example Basic Claus process and Modified Claus process . There are different chemical software are used for simulation and optimization of Claus process for example Aspen Plus and Chemcad ECT. The Gibbs free energy method is introduced and model of Claus process. There are new parameter are introduced in reaction furnace to reduce the error from 33% to 7 %. The waste heat boiler is installed at the reaction furnace in which high pressure stream is produced and study the decomposition the hydrogen sulphide. The new rate of reaction is introduced of the enhancement of H2 production in chemical process. The simulation of reaction furnace in Aspen plus software is the maximum utilization of process. Due to suitable operating condition of reaction furnace is caused the maximum destruction of ammonia gas in the reactor. When we are increasing the oxygen concentration and temperature of feed is causing decreasing the ammonia production in reaction furnace. It is below than acceptance value of ammonia is 150 ppm in the reaction furnace. The presence of oxygen components, Sulfur oxide, hydroxide components are effect on decreasing the amount of ammonia in furnace and temperature is about at 1350⁰C. It is noted that when the production of sulfur recovery is decrease in Claus process and the production of carbon monoxide is increase in the thermal section at the existence. Now we are work on parametric studies of furnace that could be causes the production of ammonia destruction and CO emission in the Claus process. Due to optimize the reaction furnace parameter are help to get large of sulfur production, ammonia gas destruction, increased the catalyst life and decreased of dangerous gases.

A overview on application of CO2 in the ironmaking and steelmaking process is presented. Study on resource utilization of CO2 is significant for the reduction of CO2 emissions and the coping with global warming. The paper introduces the research progress of CO2 utilization in the sintering, Blast Furnace, Converter, secondary refining, Continuous Casting and smelting process of stainless steel in recent years in China. According to the foreign and domestic research and application status, the paper analyzes the feasibility and metallurgical effects of the CO2 utilization in the ferrous metallurgy process. The paper mainly introduces such new techniques as 1) flue gas circulating sintering, 2) blowing CO2 through Blast Furnace tuyere and CO2 as a pulverized coal carrier gas, 3) top and bottom blowing CO2 in the converter, 4) Ladle Furnace and Electric Arc Furnace bottom blowing CO2, 5) CO2 as Continuous Casting shielding gas, 6) CO2 for stainless steel smelting, and 7) CO2 circulation combustion. CO2 has a very wide application prospect in ferrous metallurgy process and the quantity of CO2 utilization is expected to be 100kg per ton of steel. It will effectively facilitate the progress of metallurgical technology and strongly promote the energy conservation of metallurgical industry.

Process simulation represents an important tool for plant design and optimisation, either applied to well established or to newly developed processes. Suitable thermodynamic packages should be selected in order to properly describe the behaviour of reactors and unit operations and to precisely define phase equilibria. Moreover, a detailed and representative kinetic scheme should be available to predict correctly the dependence of the process on its main variables. This review points out some models and methods for kinetic analysis specifically applied to the simulation of catalytic processes, as a basis for process design and optimisation. Attention is paid also to microkinetic modelling and to the methods based on first principles, to elucidate mechanisms and calculate thermodynamic and kinetic parameters. Different case histories support the discussion. At first, we have selected two basic examples from the industrial chemistry practice, e.g. ammonia and methanol synthesis, which may be described through a relatively simple reaction pathway. Then, a more complex reaction network is deeply discussed to define the conversion of bioethanol into syngas/hydrogen or into building blocks, such as ethylene.

Process (or business process) management systems fulfill defining, executing, monitoring and managing process models deployed on process-aware enterprises. Accordingly, the functional formation of the systems is made up of three subsystems such as modeling subsystem, enacting subsystem and mining subsystem. In recent times, the mining subsystem has been becoming an essential subsystem. Many enterprises have successfully completed the introduction and application of the process automation technology through the modeling subsystem and the enacting subsystem. According as the time has come to the phase of redesigning and reengineering the deployed process models, from now on it is important for the mining subsystem to cooperate with the analyzing subsystem; the essential cooperation capability is to provide seamless integrations between the designing works with the modeling subsystem and the redesigning work with the mining subsystem. In other words, we need to seamlessly integrate the discovery functionality of the mining subsystem and the analyzing functionality of the modeling subsystem. This integrated approach might be suitable very well when those deployed process models discovered by the mining subsystem are complex and very large-scaled, in particular. In this paper, we propose an integrated approach for seamlessly as well as effectively providing the mining and the analyzing functionalities to the redesigning work on very large-scale and massively parallel process models that are discovered from their enactment event logs. The integrated approach especially aims at analyzing not only their structural complexity and correctness but also their animation-based behavioral properness, and becomes concretized to a sophisticated analyzer. The core function of the analyzer is to discover a very large-scale and massively parallel process model from a process log dataset and to validate the structural complexity and the syntactical and behavioral properness of the discovered process model. Finally, this paper writes up the detailed description of the system architecture with its functional integration of process mining and process analyzing. And more precisely, we excogitate a series of functional algorithms for extracting the structural constructs as well as for visualizing the behavioral properness on those discovered very large-scale and massively parallel process models. As experimental validation, we apply the proposed approach and analyzer to a couple of process enactment event log datasets available on the website of the 4TU.Centre for Research Data.

(1) Introduction: The COVID-19 pandemic presented unique challenges for patients and healthcare providers, especially for those working with obesity and related health problems. E-health has emerged as a crucial tool for the follow-up of users undergoing bariatric surgery during this period, allowing remote monitoring of users' health status and providing access to virtual consultation with health professionals. This study aims to analyze the impact of the use of telemedicine during the COVID-19 pandemic on the results of bariatric surgery and user satisfac-tion with this follow-up. (2) Method: Observational study with retrospective data collection. The variables were divided into several groups: health data, associated comorbidities, quality of life, quality of sleep and satisfaction with telemedicine monitoring. (3) Results: Surgery significantly affected weight loss, in general more than 75% loss of excess weight. Comorbidities, like the qual-ity of life, were reversed over time, with 50% of subjects maintaining excellent levels. Although most users were satisfied with the monitoring, the variables had no relationship. (4) Conclusions: The follow-up assured by telemedicine did not alter the results of bariatric surgery, which may allow us to infer that it may be an option to consider for regular monitoring of the post-bariatric surgery process.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

Accurate estimates of daily rainfall are essential for understanding and modeling the physical processes involved in the interaction between the land surface and the atmosphere. In this study, daily satellite soil moisture observations from the Advanced Microwave Scanning Radiometer - Earth Observing System (AMSR-E) generated by implementing the standard NASA- algorithm are employed for estimating rainfall, firstly, through the use of recently developed approach, SM2RAIN (Brocca et al., 2013) and, secondly, the nonlinear autoregressive network with exogenous inputs (NARX) neural modelling at five climate stations in the Karkheh river basin (KRB), located in southwest Iran. In the SM2RAIN method, the period 1 January 2003 to 31 December 2005 is used for the calibration of algorithm and the remaining 9 months from 1 January 2006 to 30 September 2006 is used for the validation of the rainfall estimates. In the NARX model, the full study period is split into a training (1 January 2003 to 31 September 2005) and a testing (1 September 2005 to 30 September 2006) stage. For the prediction of the rainfall as the desired target (output), relative soil moisture changes from AMSR-E and measured air temperature time series are chosen as exogenous (external) inputs in NARX. The quality of the estimated rainfall data is evaluated by comparing it with observed rainfall data at the five rain gauges in terms of the correlation coefficient R, the RMSE and the statistical bias. For the SM2RAIN method, R ranges between 0.44 and 0.9 for all stations, whereas for the NARX- model the values are generally slightly lower. Moreover, the values of the bias for each station indicate that although SM2RAIN is likely to underestimate large rainfall intensities, due to the known effect of soil moisture saturation, its biases are somewhat lower than those of NARX. In conclusion, the results of the present study show that with the use of AMSR-E soil moisture products in the physically based SM2RAIN- algorithm as well as in the NARX neural network, rainfall for poorly gauged regions can be fairly predicted.

In the discussion on environmental policies, the notion of eco-efficiency is often used. Eco-efficiency is defined as the delivery of products and services with competitive values, while reducing the ecological impacts and satisfying human needs. In an environment of great competitiveness in which the companies operate, the improvements in the productive process is one of the differentiating factors for guaranteeing a strong competition. Also it is essential rationalizing energy consumption and natural resources. For this it is necessary to understand the main operations and dynamics of the company. This work presents an empirical study of a Portuguese company in the industrial sector. The problematic here presented is based on the company’s growing concern to reduce the amount of scrap produced. From the literature research that was performed, a strong dependence relation between the different variables in the extrusion process was found. The main objective of this work is to model the aluminium extrusion process, with the aim of minimizing the production of scrap. For this several variables involved in the process are taking into account. Using statistical techniques, in particular multiple linear regressions, it was possible to identify the importance of the variables under study for the scrap production.

Product Development Process is widely known among industry and automobile companies. With the advance of technology and the need to improve product efficiency, many companies have been applying Lean Thinking principles. Their benefits lead those companies to implement their concepts and tools, like Value Stream Design in Indirect Areas, Obeya, Just-in-time (JIT) which is based on the production control system developed and implemented by Toyota. This article describes the case study of the implementation of Lean Product &amp; Process Development (LPPD) on the current Product Development Process (PDP) in an automotive company. The PDP was created by the organization and adapted from Advanced Product Quality Planning (APQP). The main findings were a Value Stream Design model of an improved PDP as a useful and successfully contribution for the company. These improvements reduced the product development lead time from 700 days to 369 days. The process efficiency increased from 68% to 85%. The communication and transparency between the cross-functional team (CFT) was improved and show promise for achieving a successful launch of new products.

Robotic Process Automation (RPA) is a fast growing field inside Business Process Automation (BPA). RPA deals with software robots that use human application interface to do some repetitive tasks like starting programs, filling the forms, clicking on buttons etc. Some RPA software tools like Blue Prism, Rapise and UiPath became popular during last years but there are still some problems with them starting with their high price and difficulties to adapt to the real use cases. On the other hand, Optoklik is a relatively small RPA tool developed to be highly adaptable to the real cases and still easy to use. This paper presents the main functions of Optoklik and discusses its usage in automation of different actions that use human application interface.

This article describes the Analytic Hierarchy Process (AHP) method which can be calculated by several methods. The AHP method is essential for the managerial decision-making to recognize which method is efficient for the calculation and to determine the proper order of criteria. In the article there are included methods that can be used in order to calculate the matrix in the AHP process for setting criteria such as Geometric mean, Arithmetic mean, Row sum of the adjusted the Saaty matrix, Reverse sums of the Saaty matrix columns and Row sums of the Saaty matrix. The paper is focused on the accuracy of the methods used. The results show that the most accurate method is the Saaty method, and the second most accurate method is the geometric mean in order to determine the ranking. This method is easier to use when the same order is achieved as in the Saaty method, followed by Geometric mean, which is favourable for fast and easy determination of alternatives using in the AHP process. The survey carried out among managers graduated from Universities and Colleges in Slovakia showed that the respondents considered the Saaty method as the most complex and also the most difficult method and the geometric mean average method the simplest method. 44% of respondents stated that they are capable to use a program to calculate the AHP. 46% of respondents said they had experience with some method related to the managerial decision-making process. 72% of managers regarded as important to manage some method for decision-making in their managerial position.

Configurable process models are frequently used to represent business workflows and other discrete event systems among different branches of large organizations: they unify commonalities shared by all branches and describe their differences, at the same time. The configuration of such models is usually done manually, which is challenging. On the one hand, when the number of configurable nodes in the configurable process model grows, the size of the search space increases exponentially. On the other hand, the person performing the configuration may lack the holistic perspective to make the right choice for all configurable nodes at the same time, since choices influence each other. Nowadays, information systems that support the execution of business processes create event data reflecting how processes are performed. In this article, we propose three strategies (based on exhaustive search, genetic algorithms, and greedy heuristic) that use event data to automatically derive a process model from a configurable process model that better represents the characteristics of the process in a specific branch. These strategies have been implemented in our proposed framework, and tested in both business-like event logs as recorded in a higher educational ERP system, and a real case scenario involving a set of Dutch municipalities.

: One of the challenges facing operations management is the design, choice and imple-mentation of action plans adapted to the magnitude of the deviations of the variables of an industrial process. Making conscious and quick decisions is crucial to achieving im-provements in productivity. This will be achieved if the organization's internal and external communication model is strategically designed, considering specific cultural factors and the symmetry or asymmetry required in the communication model. However, how do we organize ourselves and through what channels do we communicate within a production process to generate Big Data that combines data from technologies and the perception, comprehension and projection of experienced humans? Our purpose is to create an operations management model that facilitates the incorporation of technology, allows a prompt response to failures, and promotes the sustainability of processes, without losing sight of its alignment with the organizational strategy. The developed model was implemented in an operations management team, following the guidelines of an action researcher methodology. This resulted in the design of an operations management model and a detailed methodology for its implementation, achieving sig-nificant improvements in the metrics of the current process, making it a success story.

Background: The concept of Quality of Work Life (QWL) has been built multidimensionally through social reproduction; it is impacted by the perceptions of each individual and by the relationship between workers and the work environment. Objective: to analyze the Work Process and QWL of assisting nurses in public health. Methods: Research in a critical paradigm, descriptive, exploratory with a qualitative approach. The population corresponds to Nurses who work in care work. Semi-structured guiding questions were applied and were analyzed with content analysis. Results: seven participants declared female; all Chilean; seven are young adults; six singles; only one has children, and one has a person dependent on her care; six are heads of household, and five receive help with housework. All have a nursing degree, five have a diploma, but none have a postgraduate. Work Process has three subcategories: work object, instrument, organization, and work conditions; the QWL category has six subcategories: definition and perception of QWL, QWL potentiating factors, QWL exhausting factors, QWL improvement strategies, the emotional burden associated with QWL, and Health problems. Conclusions: In this way, the lifestyle built by the assistance in the health area has repercussions on the quality of life and health in general.

Porous ceramics can be realized by different methods and are used for manifold applications, like cross-flow-membranes or wall-flow-filters, porous burners, solar receivers, structural design elements or catalytic supports. Within this paper three different alternative process routes are presented, which can be used to manufacture porous ceramic components with different properties or even graded porosity. The first process route bases on additive manufacturing (AM) of macro porous ceramic components, the second on AM of a polymeric template, which is used to manufacture porous ceramic components via replica technique. Finally, the third process route bases on an AM technology, which allows the manufacturing of multi-material or multi-property ceramic components, like components with dense and porous volumes in one complex shaped component.

In this study, an experimentally validated computational model was developed to investigate the hydrodynamics in a rotor-stator vortex RVR agglomeration reactor having a rotating disc at the centre with two shrouded outer plates. A numerical simulation was performed using a simplified form of the reactor geometry to compute the 3D flow field in batch mode operations. Thereafter, the model was validated using data from a 2D Particle Image Velocimetry (PIV) flow analysis performed during the design of the reactor. Using different operating speeds—70, 90, 110 and 130 rpm, the flow fields were computed numerically followed by a comprehensive data analysis. The simulation results showed separated boundary layers on the rotating disc and the stator. The flow field within the reactor is characterized by a rotational plane circular forced vortex flow in which the streamlines are concentric circles with a rotational vortex. Overall, the results of the numerical simulation demonstrate a fairly good agreement between the CFD model and the experimental data as well as the available theoretical predictions. The swirl ratio β was found to be approximately 0.4044, 0.4038, 0.4044 and 0.4043 for operating speeds of N=70, 90, 110 and 130 rpm respectively. In terms of the spatial distribution, the turbulence intensity and kinetic energy are concentrated on the outer region of the reactor while the axial velocity showed a decreasing intensity towards the shroud. However, a comparison of the CFD and experimental predictions of the tangential velocity and the vorticity amplitude profiles shows that these parameters were under-predicted by the experimental analysis which could be attributed to some of the experimental limitations rather than the robustness of the CFD model or numerical code.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

So far, scientific studies on high frequency welding (HF) have observed the three main parameters: anode current, welding time and pressure of upper electrode. Some authors have also observed and studied the welding frequency, the power, and the values of the dielectric constants of the materials or the angle of dielectric losses. Due to the complex effects that the parameters have on the quality of the welded joint, it is necessary to extend the research and study the mutual relationships between a large numbers of process parameters on the welded joint in order to achieve satisfactory strength of the welded joint. In this research, the number of considered parameters is increased to 17, each of which is relevant to the processes of HF welding, and their mathematical equations are presented. The research is carried out on a HF welding machine improved with a linear pneumatic actuator for lowering the upper electrode and regulating the compressive force, and a measuring machine with the appropriate measuring method for determining the breaking forces with a tension gage and performing the „T“ test is made. Numerous researches were carried out on the functional changes of the process parameters of the percentage share of the values of the coupling capacitor, the anode current and the welding time on the values of the breaking forces of the welded joints. Based on the conducted research, it was concluded that the optimization of the process parameters of HF machine must be performed before the welding process, which is determined by a certain amount of energy that must be introduced into the material. These parameters are the capacity of the output capacitor, i.e., the value of the electric current flowing through the material and the time for the development of the operating power to produce welded joints with a certain strength and quality of welded joints for a specific material used in the process.

Process model discovery covers different methodologies to mine a process model from traces of process executions, and is gaining an important role in Artificial Intelligence research. Current approaches in the area, with few exceptions, focus on determining a model of the flow of actions only. However, in several contexts, (i) restricting the attention to actions is quite limitative, since the effects of such actions have to be analysed, too, and (ii) traces provide additional pieces of information, in the form of states (i.e., values of parameters possibly affected by the actions): for instance, in several medical domains traces include both actions and measurements of patients’ parameters. In this paper, we propose AS-SIM (Action-State SIM), the first approach able to mine a process model which comprehends two distinct classes of nodes, to capture both actions and states.

In the end, this paper analyzed the economy from the investment in plant construction, raw material collection, product production and product sales. The resulting products include pyrolytic carbon, pyrolytic oil, pyrolysis gas. The results showed that when the treatment scale was 1 ton h−1, the pyrolysis plants with three loading modes will always be in a state of loss during the 20-year running time. When the processing scale was 9 ton h−1, the pyrolysis plant can be profitable in the first year. In the sensitivity analysis, the influence of three pyrolysis products on the total return on investment was explored. The results showed that the price change of pyrolysis oil has the greatest influence on the total return on investment (Total ROI) under the three loading methods, The price change of pyrolysis gas has minimal impact on the Total ROI. This study provides basic data and basis for the commercialization of coal-biomass co-pyrolysis technology and investment in plant construction.

Drowning is a leading cause of accidental death worldwide, with traditional drowning prevention strategies focused on buoyancy aids and protective equipment proving insufficient in mitigating the immediate risks of cold water shock and drowning. Swiftwater Breathing Apparatus (SWBA) has emerged as a potential game-changer, offering respiratory protection at the water's surface and a means of interrupting the drowning process. This report examines how SWBA can disrupt the drowning process, the benefits of using SWBA compared to existing protective equipment, the issue of water rescuer fatalities, and the potential implications for insurers and coronial inquests.

Additive Friction Extrusion Deposition (AFED) is a recently developed additive manufacturing technique that promises high deposition rates at low forces. Due to the novelty of the process, the underlying phenomena and their interactions are not fully understood, and in particular the processing strategy and tool design are still in their infancy. This work contributes to the state of the art of AFED through a comprehensive analysis of its working principles and an experimental program including a representative sample component. The working principle and process mechanics of AFED are broken down into their individual components. Forces, their origins and effects on the process are described, and measures of process efficiency and theoretical minimum energy consumption are derived. Three geometrical features of the extrusion die are identified as most relevant to the active material flow, process forces and deposition quality: the topography of the inner and outer circular surfaces and the geometry of its extrusion channels. Based on this, the experimental program investigates seven different tool designs in terms of efficiency, force reduction and throughput. The experiments using AA 6061-T6 as feedstock show that AFED is capable of both high material throughput (close to 550 mm³/s) and reduced substrate forces: For example, the forces for a run at 100 mm³/s remained continuously below 500 N, and for a run at 400 mm³/s below 3500 N. Material flow and microstructure of the AFED are assessed from the macrosections. Significant differences are found between the advancing and retracting sides for both process effects and material flow. Banded structures show strong similarities to other solid state processes. The fabrication of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical testing, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, in the microstructure show strong similarities to other solid-state processes. The manufacturing of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical tests, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, while in the horizontal direction of the structure mechanical properties corresponding to a T4 temper have been achieved.

This paper studied the dynamic characteristics of the deployment process of the replaceable interface mast and the vibration generated at the end of the mast. The interface is discretized by the absolute nodal coordinate thin shell element with gradient reduction, and the three-dimensional motion of the reconfigurable rigid body module is described by the natural coordinate method. The dynamic equations of the interface and the reconfigurable module without external constraints are established by the principle of virtual work. Finally, the dynamic models of each part are assembled into the dynamic model of the mast system deployment process through the system constraint equation. According to the established dynamic model of the mast system deployment process, the dynamic behavior changes of the replaceable interface mast are analyzed. At the same time, the differences in the deployment behavior of the replaceable interface mast under different system configuration schemes, flexible interface geometric parameters, and different driving laws are studied and compared. It provides guidance for the scheme configuration of the mast system, the structural design of the interface, and the deployment motion planning of the mast. According to the physical prototype and the assembly of the mast system model, the deployment process of the replaceable interface mast is experimentally analyzed. It shows that the established dynamic model of the mast system can correctly analyze the dynamic characteristics of the deployment behavior of the replaceable interface mast, which provides a reference for the design and behavior analysis of the mast system.

By employing the stochastic extension of the Madelung quantum-hydrodynamic description within a discrete methodology, we establish a solution using the path integral approach to explore the progression of quantum states' superposition. This investigation aims to understand the eventual establishment of a stable end-state configuration amid the backdrop of gravitational background fluctuations. The model identifies the circumstances that lead to a limited range of interaction for the quantum potential, allowing for the emergence of sizeable, classically described macroscopic phenomena. The theory unveils the lowest achievable level of uncertainty in an open quantum system and investigate its congruence with the localized behaviors of macroscopic classical systems. The study examines agreements and differences with decoherence theory and the Copenhagen interpretation of quantum mechanics, and evaluates the impact of wave function decay on the measurement process.

Due to the non-degradability of petroleum-based packaging materials, serious environmental pollution and the depletion of non-renewable resources have become pressing issues. In order to actively promote green production and address these concerns, there is an urgent need for new packaging materials to replace traditional plastic products. Starch-based packaging materials, composed of starch, fiber, and plasticizers, offer a degradable and environmentally friendly alternative. Starch alone cannot undergo thermoplastic processing due to its inherent structural characteristics. Therefore, researchers have explored modifications by incorporating plasticizers to create processable thermoplastic starch (TPS). However, there are challenges related to the high crystallinity and poor compatibility between TPS and fibers, resulting in decreased mechanical properties. To address these challenges, a novel approach combining plasticizer optimization and response surface method (RSM) optimization has been proposed to enhance the mechanical properties of starch-based packaging materials. This method leverages the advantages of composite plasticizers and process parameters. The findings demonstrate that the composite plasticizer effectively disrupt the hydrogen bonding and granule morphology of starch, leading to a significant reduction in crystallinity. Based on these findings, the optimal process parameters are determined using the RSM, resulting in a forming temperature of 198 °C, forming time of 5.4 minutes, and AC content of 0.84 grams. Compared with the non-optimized values, the tensile strength increases by 12.2% and the rebound rate increases by 8.1%.

In principle, modular or integral character of manufacturing lines depends on topological designs of products and determined operation tasks. On the other hand, in specific situations there is an articulated need for modular design in smart manufacturing systems, since modular layouts are a crucial step towards agile production via smart manufacturing. The aim of this paper is to explore how the modular layout relates to manufacturing lead time (MLT) and to operational complexity of smart manufacturing systems. For this purpose, topologically different models of alternative process layouts were simulated and tested, while MLT values were obtained using Tecnomatix Plant Simulation. Obtained positive findings of this research could be useful not only in selection of the most suitable process design from the alternative ones, but especially in deepening knowledge and better understanding of the concept of optimal network modularity.

Burkina Faso is a sub-Saharan African country with a high poverty rate that has quadruplicated its population in the last half fifty years, that is, from 4.5 to 18 million inhabitants. Such demographic changes together with an intense migration process from rural areas to large cities, among other issues, are contributing to a rapid process of socio-cultural transformation. In this context, changes in both traditional and contemporary housing are analyzed and a complete ther-mo-hygrometric evaluation is carried out by processing significant data from on-site measure-ments to shed new light on the response of the said dwellings to the environmental and local cultural values. Results show that the introduction of land ownership linked to climate change and the increasing scarcity of natural resources are forcing native ethnic groups to modify their traditional ways of life, threatening their subsistence. Consequently, we can prove that the new building typologies are not in the least suitable for the climatic conditions nor the rich cultural heritage of Burkina Faso. This fact, negatively affects the possibility of revitalizing vernacular and environmentally-oriented solutions for the contemporary world and the necessary advance to-wards a more sustainable architecture.

Several studies have highlighted the importance and evolution of process safety leadership and culture in various industries. However, none has focused on the palm oil milling industry yet. This paper critically reviews the latest developments in the palm oil milling process and unit operations leading to process safety concerns. It also discusses the Principle of 3C that is applied to explain repeat accidents and the four-level safety culture in the palm oil milling industry. For this purpose, the author presents case studies of two key palm oil companies in Malaysia. Overall, this paper offers guidelines to leaders in the palm oil milling industry about the required process safety leadership and culture to be understood in order to improve their safety outcomes.

Cutaneous lymphocytosis (CL) is an uncommon and controversial lymphoproliferative disorder described in dogs and cats. CL is generally characterized by a heterogeneous clinical presentation and histological features that may overlap with epitheliotropic lymphoma. Therefore, its neoplastic or reactive nature is still debated. Here, we describe clinicopathological, immunohistochemical and clonality features of a retrospective case series of 19 cats and 10 dogs with lesions histologically compatible with CL. In both species, alopecia, erythema and scales were the most frequent clinical signs. Histologically, a dermal infiltrate of small to medium-sized lymphocytes, occasionally extending to the subcutis, was always identified. Conversely, when present, epitheliotropism was generally mild. In cats, the infiltrate was consistently CD3+; in dogs, a mixture of CD3+ and CD20+ lymphocytes was observed only in 4 cases. The infiltrate was polyclonal in all cats, while BCR and TCR clonal rearrangements were identified in dogs. Overall, cats had a long-term survival (median overall survival=1080 days) regardless of the treatment received, while dogs showed a shorter and variable clinical course, with no evident associations with clinicopathological features. In conclusion, our results support a reactive nature of the disease in cats, associated with prolonged survival; despite a similar histological picture, canine CL was associated with a more heterogeneous lymphocytic infiltrate, clonality results, and response to treatment.

Communication is indispensable for today's lifestyle, and thanks to technology, millions of people can communicate as quickly as possible. The effect of this breakthrough has transformed organizations to the degree that they generate billions of emails daily to facilitate their operations. There is implicit information behind this vast corpus of human-generated content that can be mined and used for their benefit. This paper tries to address the opportunity that email logs can bring to organizations and propose an approach to discover process models by combining supervised text classification and process mining. This framework consists of two main steps, text classification, and process mining. First, Emails will be classified with supervised machine learning, and to mine, the processes fuzzy Miner is used. To further investigate the application of this framework, we also applied this framework over a real-life dataset from a case study organization.

There are thousands of rare genetic diseases that could be treated with classical gene therapy strategies such as the addition of the defective gene via viral or non-viral delivery or by direct gene editing. However, several genetic defects are too complex for these approaches. These “genomic mutations” include aneuploidies, intra and inter chromosomal rearrangements, large deletions, or inversion and copy number variations. Chromosome Transplantation (CT) refers to the precise substitution of an endogenous chromosome with an exogenous one. By the addition of an exogenous chromosome and the concomitant elimination of the endogenous one, every genetic defect, irrespective of its nature, could be resolved. In the current review, we analyze the state of the art of this technique and discuss its possible application to human pathology. CT might not be limited to the treatment of human diseases. By working on sex chromosomes, we showed that female cells can be obtained from male cells, since chromosome-transplanted cells can lose either sex chromosome, giving rise to 46,XY or 46,XX diploid cells, a modification that could be exploited to obtain female gametes from male cells. Moreover, CT could be used in veterinary biology, since entire chromosomes containing an advantageous locus could be transferred to animals of zootechnical interest without altering their specific genetic background and the need for long and complex interbreeding. CT could also be useful to rescue extinct species if only male cells were available. Finally, the generation of “synthetic” cells could be achieved by repeated CT into a recipient cell. CT is an additional tool for genetic modification of mammalian cells.

Pyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article focuses mostly on recent achievements in the technical and processing aspects of pyrolysis. This review provides an overview of the recent advanced pyrolysis technology used in gas, bio-oil, and biochar production. The key parameters to maximize the production of specific chemical compounds were discussed and considered during the construction of the reactors. The emphasis is put on optimizing the process parameters, technical requirements, and renewable energy use in the process and conception to improve the efficiency of product production. The application of pyrolysis gas, oil, and biochar as valuable chemical compounds are related to the intensifying effects of climate change, biofuel production, and waste management in accordance with the principles of sustainable development.

Spatial data conflation plays a fundamental role in in many aspects of modern Geographic Information Systems (GIS) research and development such as geospatial data visualization, incremental updating of databases and disaster evaluation. The primary objective of conflation is to derive valuable information based on the comparison of multiple spatial data sources of homogeneous or heterogeneous nature. This paper reviews the state of art of the concept of conflation, feature matching, the most important progresses of conflation between image and road network data, and the complexity of spatial conflation.

Business processes are continuously evolving in order to adapt to changes due to various factors. One important process drift perspective yet to be investigated is the detection of branching condition changes in the process model. None of the existing process drift detection methods focus on detecting changes of branching conditions in process models. Existing branching condition detection methods do not take changes within the process into account, hence results are inadequate to represent the changes of decision criteria of the process. In this paper, we present a method which can detect branching condition changes in process models. The method takes both process models and event logs as input, and translates event logs into decision sequences for change points detection. The proposed method is evaluated by simulated event logs.

The environmental safety of a car is currently one of the most important indicators of the vehicle competitiveness and quality in the consumer market. Currently, the assessment of the ecological properties of vehicles can be made based on various criteria. In the case of combustion-powered cars, the most attention is usually paid to the values characterizing their use, and in the environmental assessment, first of all to pollutant emissions and operational fuel consumption. The proposed article considers the possibility of using the life cycle assessment to analyze the ecological properties of a passenger car during its operation. A simplified LCA method of the vehicle was presented, which in strictly defined cases can be used for the analysis of environmental impacts and the assessment of the energy analysis related to its operation. For this purpose, a vehicle life cycle model was developed. Data on the operation of 33 passenger cars of different manufacturers with similar operational characteristics, coming from different production periods, were analyzed in detail. The obtained results were found to be highly sensitive to the assumptions made in the article.

Permafrost hydrology is an emerging discipline, attracting increasing attention as the Arctic region is undergoing rapid change. However, the research domain of this discipline had never been explicitly formulated. Both 'permafrost' and 'hydrology' yield differing meanings across languages and scientific domains, hence 'permafrost hydrology' serves as an example of linguistic relativity. The differing views of permafrost as either an ecosystem class or a geographical region, and hydrology as a discipline concerned with either landscapes or generic water bodies, maintain a language-specific touch in the definition of permafrost hydrology. From this point of view, the English and Russian usage of this term is explained. A universal process-based definition is further proposed, developed on a specific process assemblage, including (i) water table dynamics caused by migration of an upper aquitard through freeze–thaw processes; (ii) water migration in soil matrix, driven by phase transitions in the active layer; (iii) transient water storage in solid state in the subsurface compartment. This definition is shown to fill the niche in existing vocabulary, and other definitions from northern hydrology field are revisited.

Museums and Science Centres are informal education environments that intend to engage the visitors with their exhibits. We present an efficient design process that allows an improved working relationship between museum practitioners, exhibition designers, and visitors. We present the principles and a graphical representation based on the Engagement Profile from previous work. Elements of the design process are evaluated using a learning game at the science centre Engineerium. The evaluation is based on a study with over five hundred visitors to the science centre.

Partial differential representation of self-similarity feature has been derived from notion of the homogenous function in general sense. This representation allows consideration of stochastic self-similar systems. As well as the partial differential representation allows consideration of Stochastic Partial Differential Equation.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

This paper investigates the potential of different fermentation feedstocks towards succinic acid production. Three alternative flowsheets were constructed and modelled in SuperPro Designer™, utilizing different fermentation substrates: crude glycerol (a by-product of the biodiesel industry), a commercial 95% glucose syrup and pure glycerol. Techno-economic analysis of the modelled plants showed that all three potential investments can be economically profitable, with the crude glycerol case as the most promising one. The succinic acid production cost for the crude glycerol scenario is estimated at 3.59 $/kg, while a thorough study of the capacity effect to the economics showed that it could drop as low as $2.6 $/kg. Parametric analysis and optimization performed on a flowsheet level, indicated opportunities for lowering the production cost down to 3 $/kg, a value that could pave the framework for a further potential decrease in the selling price of the product.

In this study, we investigate the behavior of randomly moving particles with a defined average energy, focusing on their biased motion around a specific point. These particles' velocity magnitudes follow a Maxwell distribution with a specific scale parameter. Our analysis derives the stochastic rotation rules for these particles and introduces the Ito equation conditions for biased stochastic rotation at a given curl value. We also consider the special relativistic-like effects in this context. The findings are validated through a representative example.

In this paper, the computational fluid dynamics (CFD) method has been used to simulate the gas flow and the catalytic hydrogenation process of the C-2 hydrogenation adiabatic reactor in a practical ethylene production unit of a chemical plant. The laminar finite-rate model was used for the chemical reaction model. The standard two-equation model was used for the turbulence model. The exponent-function kinetic model was used for the reaction dynamics model. The simulation results were in good agreement with the actual industrial data obtained from the C-2 hydrogenation reactor, and the distributions of reaction parameters such as temperature and component concentrations in the reactor were further analyzed. Based on the validated CFD models, the structure and operating conditions of the reactor, as well as hydrogen load distribution ratios, are simulated for comparing the comprehensive performance metrics of ethylene selectivity and acetylene conversion rate; as a result, we can obtain the optimal temperature of 312 K, the optimal hydrogen/acetylene ratio of 0.10 as well as the optimal hydrogen load distribution ratio of 4:4:2, and the diameter/height ratio exerts a marginal effect on the selectivity, conversion rate and harmonic mean of the reactor.

Inflammation is an essential protective response against injury or infection. Physiological inflammation eliminates the pathogen, promotes tissue repair and healing. An exaggerated, out of control inflammation, however, can become pathological. Inflammation can generate secondary cell damage, inflame the vessels (endothelitis), activate coagulation processes. Among these pathogenetic factors (cell damage, inflammation, endothelitis, coagulopathies), self-amplification mechanisms can be created, spreading beyond the initial site, up to Multiple Organ Failure (MOF) and host death. If the inflammation does not resolve in a physiological way, the remodeling of the tissues can be maladaptive and lead to the onset of chronic inflammatory degenerative diseases. Diseases such as sepsis, burns, polytrauma, severe forms of influenza or COVID-19, are characterized by a condition of hyperinflammation, associated with a condition of immunosuppression. The initial events triggered by the pathogen (cell damage, interferon response in the case of viruses) ignite the inflammation by activating the inflammasome, the transcription factor NFkB, the release of pro-inflammatory eicosanoids (Prostaglandins, Leukotrienes, Thromboxanes) by neutrophils and macrophages. Hence, the cells of the innate immune system produce pro-inflammatory cytokines. Indeed, the ‘’eicosanoid storm’’ precedes the ‘’cytokine storm’’. Eicosanoids are a group of potent endogenous lipid mediators derived from omega-6 fatty acids Arachidonic Acid (AA). Eicosanoids include a group of molecules with pro-inflammatory (Prostaglandins, Leukotriens) and pro-coagulant (Thromboxanes) action. In addition, Arachidonic Acid (AA) is the source of Lipoxins (LXs). Lipoxins belong to a group of molecules collectively referred to as specialized pro-solving mediators (SPMs) which also include molecules derived from w-3 eicosapentaenoic acid (EPA): Resolvins (ReV-E sieres) and w-3 docohexanoic (DHA): Resolvins D-series (ReV D-series); Protectins (PTs); Maresins (MaRs). SPMs are important for the resolution phase of inflammation to take place properly. Their deficiency could be involved in both acute uncontrolled inflammation and chronic inflammation. The active regulation of the acute inflammatory process, integrating the precursors of Specialized Pro-resolving Mediators (SPMs), such as ⍵-6 and ⍵-3 in balanced ratio, or the SPMs themselves, could be a complementary therapeutic approach useful for taming the "storm of cytokines '' which characterizes exaggerated forms of inflammation. ⍵-3 and ⍵-6 are part of already widely used, readily available, inexpensive and safe supplements. Resolvins have already been included in clinical trials for various other inflammatory diseases (eye diseases, periodontal diseases).

The study of co-fusion was one of the essential topics in the history of metallurgy in China. Simulation experiments had been an essential concept in the study of the co-fusion steelmaking process. This paper mainly studied the simulation experiments of co-fusion from two aspects: the replication of co-fusion swords by three different methods, and the micro-analysis of the co-fusion samples. The experimental results indicated that several co-fusion swords could be made by different processes, but the carbon content and surface hardness were quite different. During repeated forging welded, the microstructure of the samples transformed from laminated to homogenized, finally the steel with a uniform carbon content was obtained. It was challenging to find the characteristics of co-fusion from the homogenized samples. The results prompted people to rethink the microstructure characteristics of ancient co-fusion artifacts.

Background and objectives: Quality assurance and institutional accreditation in education is becoming of paramount importance. This study aims to assess the impacts of the accreditation process of the National Center for Quality Assurance and Accreditation (NCAAA) on the quality of education in one of private university in Libya. Methods: The research adopts a descriptive study design in University of Tripoli Alahlia (UTA) where an official accreditation process was completed by the NCQAA during 2017-2019. Data were collected using the self-study report that produced by the NCQAA accreditation committee during the accreditation process, and were retrieved in specific data collection sheet by one of the authors. Results: The NCQAA accreditation process that lasted about 4 years brought significant changes in the educational progressions and made the staff members more aware of quality issues in education. Our findings also reported significant improvements in the quality of education in the university. Conclusions: The process of NCQAA accreditation conducted in UTA has been positively improved the quality of education. Data from other institutions would also expressively increase the relevance and rationality of the study.

A new requirement for the manufacturing companies in Industry 4.0 is to be flexible with respect to changes in demands, requiring them to react rapidly and efficiently on the production capacities. Together with the trend to use Service-Oriented Architectures (SOA), this requirement induces a need for agile collaboration among supply chain partners, but also between different divisions or branches of the same company. In order to address this collaboration challenge, we~propose a novel pragmatic approach for the process analysis, implementation and execution. This~is achieved through sets of semantic annotations of business process models encoded into BPMN 2.0 extensions. Building blocks for such manufacturing processes are the individual available services, which are also semantically annotated according to the Everything-as-a-Service (XaaS) principles and stored into a common marketplace. The optimization of such manufacturing processes combines pattern-based semantic composition of services with their non-functional aspects. This is achieved by means of Quality-of-Service (QoS)-based Constraint Optimization Problem (COP) solving, resulting in an automatic implementation of service-based manufacturing processes. The produced solution is mapped back to the BPMN 2.0 standard formalism by means of the introduced extension elements, fully detailing the enactable optimal process service plan produced. This approach allows enacting a process instance, using just-in-time service leasing, allocation of resources and dynamic replanning in the case of failures. This proposition provides the best compromise between external visibility, control and flexibility. In this way, it provides an optimal approach for business process models' implementation, with a full service-oriented taste, by implementing user-defined QoS metrics, just-in-time execution and basic dynamic repairing capabilities. This paper presents the described approach and the technical architecture and depicts one initial industrial application in the manufacturing domain of aluminum forging for bicycle hull body forming, where the advantages stemming from the main capabilities of this approach are sketched.

Water pollutants removal by biomass adsorbent has been considered innovative and cost effective, thus commendable for application in industrial applications. However, certain important aspects have been overlooked by researchers, namely the efficiency in the operation time and pollutant removal. In this research, landfill leachate samples with organic components were treated using bentonite-enriched with sawdust augmented (SBR) process. By modifying the pH, the sawdust samples were categorized into three: the acidic, the alkaline, and the neutral. To bentonite samples, the pH-adjusted sawdust was added at 10%, 20%, and 30% amounts by mass respectively. At the optimum aeration rate of 7.5 L/min and contact period of 22 h, the treatment achieved 99.28% and 95.41% removal of COD and NH₃-N with bentonite respectively. For both pollutants, in the presence of sawdust, the removal reduced by about 17% with contact period reduced to 2 h which was a considerable achievement.