To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

This study aims to improve the shaft with hexagon joints to be a type not requiring welding or bolts in the static load test . In order to evaluate the bearing capacity of helical piles, two sites were selected to conduct pile installation for the field test and the pile load test. For the pile load test, the static pile load test and the dynamic pile load test were carried out, and torque was measured during pile installation for the field test to compare and analyze expected bearing capacity and thus assess the feasibility of the method for estimating the bearing capacity. The field pile load test revealed the bearing capacity of the gravity grout pile was the same or greater than 600kN in the static pile load test in accordance with AC 358 Code. The non-grout pile showed the bearing capacity the same or smaller than 600kN, suggesting gravity grouting is required. Moreover, the field pile load test was used to establish the bearing capacity equation considering the torque in pile installation, and a small number of samples were used to establish the equation which can be used as a basic data.

Tracked vehicles play a vital role in accessing challenging terrains, offering stability, traction, and versatility for various applications, including deep-sea exploration. However, the seafloor and sediment contain valuable but poorly understood resources, making it a significant challenge for tracked vehicles during exploration. Consequently, it is imperative to conduct comprehensive studies before considering these terrains for off-road purposes. In this study, we developed a rigid, flexible track vehicle equipped with various sensors, focusing on monitoring pressure sinkage. Cohesive soils like Bentonite and Diatom soil, particularly when combined with sand and gravel mixtures, were used for the investigation and assessed for ground pressure, bearing capacity, and sinkage in rigid-flexible tracked vehicles on these characterized terrains under varying moisture conditions. Our findings indicated that increased moisture content in bentonite soil resulted in significantly higher track slippage and sinkage compared to diatomaceous earth soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics compared to bentonite soil. These significant variations between these two soil types under changing moisture conditions highlight the complexity of such terrains. Therefore, understanding the soil and its physical properties is crucial before applying them to natural terrains. Furthermore, this study emphasizes the importance of precision in assessing the physical properties of natural terrains for the development of tracked vehicles for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

Background: Ankle fractures, comprising about 10% of musculoskeletal injuries, pose a significant healthcare burden with an increasing incidence, particularly among an aging population. This study focuses on isolated Danis-Weber type B fractures. Recent trends lean towards surgical intervention for anatomical restoration, quicker recovery, albeit with associated complications. This report aims to assess the safety and efficacy of NewClip narrow locking plate system with early weight bearing in treating isolated fibular fractures. Methods: The study includes patients with Danis-Weber type B fractures surgically treated with NewClip narrow locking plate system. Exclusions involved nondisplaced fractures, open fractures, or those requiring additional fixation.Results: Fifteen patients were enrolled in this study. Minor complications, including wound swelling, were observed in two cases. The Visual Analogue Scale (VAS) for pain exhibited a steady decline postoperatively, with almost complete resolution by the third month. At three months, the FAOS demonstrated excellent results, and final follow-up at twelve months revealed complete osseous healing without complications.Conclusions: The use of this type of plates in treating isolated fibular fractures with early weight bearing shows promising results in terms of fracture healing, pain resolution, and functional outcomes warranting further investigation with larger cohorts.

In the field of engineering, tracked vehicles play a significant role in accessing challenging terrains. Maintaining trafficability is of the utmost importance when it comes to tracked vehicles traversing rugged terrains; it provides stability, traction, and adaptability for a wide range of applications, including deep-sea exploration. The terrain characteristics pertain to the interactions that determine the mobility of tracked vehicles. Traditional Terramechanics models are in-adequate in depicting the correlation between tracks and soil. An important issue is the lack of consideration for the moisture content in the soil and the rate at which sinking occurs in these models. Examining sinkage speed helps describe the ability of tracked vehicles to move at high speeds. The focus is on the critical factors influencing the mobility of tracked vehicles, precisely the sinkage speed and its relationship with pressure. Experimental tests in a soil bin, utilizing Bentonite/Diatom sediment soil, aim to measure these terrain factors. The study introduces a rubber-tracked vehicle, pressure, and moisture sensors to monitor pressure sinkage and moisture, evaluating cohesive soils (Bentonite/Diatom) in combination with sand and gravel mixtures. Findings reveal that higher moisture content in Bentonite soil leads to increased track slippage and sinkage compared to Diatom soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics in contrast to bentonite soil. The distinct behaviors of these soils underscore the complexity of terrains, emphasizing the need for a meticulous understanding of soil properties before applying them in natural environments. Furthermore, this study contributes precision in assessing natural terrains, enhancing tracked vehicle design, and advancing terrain mechanics comprehension for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

Familial Alzheimer’s disease (FAD) can be caused by mutations in PSEN1 that encodes presenilin-1, a component of the gamma-secretase complex that cleaves amyloid precursor protein. Alterations in calcium (Ca2+) homeostasis and glutamate signaling are implicated in the pathogenesis of FAD, however it has been difficult to assess in humans whether or not these phenotypes are the result of amyloid or tau pathology. This study aimed to assess early calcium and glutamate phenotypes of FAD by measuring the Ca2+ response of induced pluripotent stem cell (iPSC)-derived neurons bearing PSEN1 mutations to glutamate and the ionotropic glutamate receptor agonists NMDA, AMPA and kainate compared to isogenic control and healthy lines. The data shows that in early neurons, even in the absence of amyloid and tau phenotypes, FAD neurons exhibit increased Ca2+ responses to glutamate and AMPA, but not NMDA or kainate. Together this suggests that PSEN1 mutations alter Ca2+ and glutamate signaling as an early phenotype of FAD.

Elevated serum uric acid (sUA) is associated with risk of developing cardiovascular disease (CVD). Here, we examined the prognostic significance of sUA and exercise capacity in 411 Japanese adults (age, ≥65; mean, 81 years) hospitalized for worsening CVD. Mean sUA was significantly higher in the 23% of patients on an sUA-lowering agent than in those not. When the patients were stratified by sUA into three groups (7.0 mg/dL), the high sUA group had significantly worse peak VO2 and composite endpoint (rehospitalization due to worsening CVD and all-cause mortality) compared with low and moderate sUA groups (P < 0.001). When the patients were stratified by sUA into five groups (sUA 10.0 mg/dL), the incidence of the composite endpoint was significantly higher in the highest sUA group compared with that in the reference group, but only in women. Univariate Cox regression analysis, but not a multivariate analysis, indicated that sUA was significantly associated with the composite endpoint. Although sUA and exercise capacity may have some degree of prognostic significance in older patients with CVD, this significance may differ between men and women.

Mechanical power and motion are often transmitted by the gear-rotor-bearing system. When there are fitting clearances between the housing and outer ring in bearings, complex vibration responses will be generated, which makes the operating status difficult to identify. Therefore, for analyzing dynamic responses, a dynamic model of gear-rotor-bearing systems with bearing fitting clearances is proposed. In the model, the bearing system with fitting clearances and gear pair system are combined, and the coupling relationship is determined by the gyroscopic mo-tion of the shaft. The friction force and collision force caused by fitting clearances are also con-sidered, which are simulated by the Coulomb friction model and Hertz theory. The result shows that the meshing stiffness will also be excited by the bearing displacement. When there are fit-ting clearances on the bearing, the amplitude modulation of the bearing outer raceway to the system time-domain response is intensified, and the multiple harmonic frequency of bearings and gear pairs are generated on the spectrum, as well as defect frequencies of gear pairs. As the fitting clearance is increased, the higher multiple harmonic responses will be caused. Although the response amplitude of the gearbox is increased by raising the input speed, multiple harmon-ic responses are suppressed, which makes the system mainly vibrate at the fundamental fre-quency. Then, the dynamic model and the vibration analysis are experimentally verified.

Optical backbone networks constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is a key factor influencing optical network performance, it is important to understand how topological and physical properties impact its behavior and to have the capability to estimate its value. In this context, we propose here a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with constrained routing techniques for traffic routing. As this type of routing can lead to traffic blocking, particularly due to the limitation on the number of wavelengths per fiber, we also propose a fiber assignment algorithm designed to deal with this problem. We apply this method to a set of randomly generated networks using a modified Waxman model, and for a network with 60 nodes, in a scenario without blocking, we obtain capacities of about 2.5 Pbit/s for a symbol rate of 64 Gbaud and about 5 Pbit/s for a symbol rate of 128 Gbaud. Remarkably, this duplication in the total network capacity is achieved by an increase in the total fiber length of only about 51%.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Background: Mental capacity is a fundamental aspect that enables patients to fully par-ticipate in various healthcare procedures. To assist healthcare professionals (HCPs) in assessing patients' capacity, especially in the mental health field, several standardized tools have been developed. These tools include the MacArthur Competence Assessment Tool for Treatment (MacCAT-T), the MacArthur Competence Assessment Tool for Clinical Research (MacCAT-CR), and the Competence Assessment Tool for Psychiatric Advance Directives (CAT-PAD). The core dimensions explored by these tools include Understanding, Appreciation, Reasoning, and Expression of a choice. Objective: This meta-analysis aimed to investigate potential differences in deci-sion-making capacity within the healthcare context among groups of patients with bi-polar disorder (BD) and schizophrenia spectrum disorder (SSD). Methods: A systematic search was conducted on Medline/Pubmed, and Scopus. Addi-tionally, Google Scholar was manually inspected, and a manual search of emerging re-views and reference lists of the retrieved papers was performed. Eligible studies were specifically cross-sectional, utilizing standardized assessment tools, and involving pa-tients diagnosed with BD and SSD. Data from the studies were independently extracted and pooled using random-effect models. Hedges g was used as a measure for outcomes. Results: Six studies were identified, with three studies using the MacCAT-CR, two studies the MacCAT-T, and one the CAT-PAD. The participants included 189 individuals with BD and 324 individuals with SSD. The meta-analysis revealed that patients with BD performed slightly better, and the difference was statistically significant, compared to patients with SSD, particularly in the domain of Appreciation (ES=0.23, 95% CI: 0.01 to 0.04, p=0.037). There was no statistically significant difference between the two groups for Understanding (ES=0.09, 95% CI: - 0.10 to 0.27, p=0.352), Reasoning (ES=0.18, 95% CI: - 0.12 to 0.47, p=0.074), and Expression of a choice (ES = 0.23, 95% CI: - 0.01 to 0.48, p=0.60). In the sensitivity analysis, furthermore, when considering only studies involving patients in symptomatic remission, the difference for Appreciation also resulted in non-significant (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). Conclusions: These findings indicate that there are no significant differences between patients with BD and SSD during remission phases, while differences are minimal during acute phases. The usefulness of standardized assessment of capacity at any stage of the illness should be considered, both for diagnostic-therapeutic phases and for research and advance directives. Further studies are necessary to understand the reasons for the overlap in capacity between the two diagnostic categories compared in this study.

In order to tackle the issue of severe rocking phenomenon under seismic conditions in structures equipped with steel spring isolation bearings, this paper investigates a novel type of anti-rocking bearing. Firstly, the structural configuration and working principle of the novel anti-rocking bearing are introduced, and a design method for bearing parameters is proposed. Secondly, a finite element analysis model is established using SAP2000 software to conduct nonlinear dynamic time history analysis under seismic loading. The analysis results show that the structural arrangement of the novel anti-rocking bearing reduces both the vertical displacement difference and the rocking angle of the isolation layer. The bearing exhibits a certain level of anti-rocking effect, but it may cause significant tensile forces in some bearings, necessitating the installation of anti-tensile reinforcement. The effectiveness of the anti-rocking effect improves as the stiffness of the steel tension rod in the bearing increases; however, it also leads to higher maximum tension in individual bearings as well as the total tension in all bearings. For structures equipped with the novel anti-rocking bearing, the acceleration amplifies under most cases, with amplification coefficients ranging from 0.82 to 1.55. The performance of the novel anti-rocking bearing varies significantly for different seismic waves. The stiffness of the steel tension rod should be determined considering the reference pressure of the bearing and the maximum designed tension of the bearing. Through the finite element simulation of the bearing, the mechanical properties of the bearing are basically the same as the theoretical analysis results. For the cylinder and the joint bearing, certain structural measures need to be taken to ensure its strength and stiffness.

The human landscape transforming activity contributes to the global change of vegetation in different forms. Hunting is one of the most ancient human landscape-shaping activities. Feeders for hunting are particularly disruptive to vegetation. In the present study, we conducted a vegetation survey in these highly disturbed places. We are investigating the vegetation dynamics over several years in in the turkey oak–sessile oak zone, in two areas with different moisture and shade conditions (forest and clearing). One important background factor is changes in precipitation and temperature. The novelty of our present study lies in the fact that the observation takes place with continuous disturbance, where the human influence is very large. Our results confirm that the weed infestation be detectable at bait sites over a long period, and the interannual changes were typical in every year, according to the fact that in August, more weed species are usually present with a greater cover at the bait sites. The main meteorological factors played a role in the degree of weed infestation in each year. There was a higher proportion of vegetation regeneration in wetter years, while dry periods do not favor successional processes. With the drying of the climate, the disturbed areas are constantly losing their natural value, but wetter weather is not an automatic solution either. A more precise understanding of vulnerable systems and careful planning of treatment interventions is necessary.

Efficiency improvement is the new challenge in all fields of design. In this scenario the reduction of power losses is becoming more and more a main concern also in the design of power transmissions. Appropriate models to predict power losses are therefore from the earliest stages of the design phase. The aim of the project is to carry on lubrication simulations of several variants of a cylindrical-roller-bearing to understand the lubricant distribution and the related churning power losses. Several strategies to reduce the computational effort have been used. Among them the sectorial symmetry and three innovative meshing strategies (purely analytical with and without interfaces and analytical/subtractive) that have been implemented in the OpenFOAM® environment. The results of the different approaches were compared among them and with experimental observations showing good agreement and reasonable savings in terms of computational effort.

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

The antioxidant properties and polyphenol content of some selected aromatic plants grown in Greece were studied. Plants were refluxed with 60% methanol after acid hydrolysis. The phenolic substances were quantified by HPLC-DAD. The antioxidant capacity of the extracts was determined with the Rancimat test using sunflower oil as substrate. Free radical scavenging activity was measured using the stable free radical 1, 1-diphenyl-2-picrylhydrazyl (DPPH). Results were compared with standard BHT and ascorbic acid. Total phenol concentration of the extracts was estimated with Folin-Ciocalteu reagent using gallic acid as standard.

The study evaluated potassium peroxymonosulfate (PPMS) efficacy against rifampicin-resistant Salmonella Infantis (rif-SI), Escherichia coli (E. coli), Salmonella Infantis (SI), Newcastle disease virus (NDV) and avian influenza virus (AIV). The assessment encompassed varied concentrations, organic material conditions, and exposure durations to comprehensively evaluate PPMS efficacy. Moreover, PPMS’s efficacy was tested on diverse carrier surfaces and clothing to evaluate its bactericidal and virucidal potential. At the recommended concentrations (1X), PPMS effectively inactivated all pathogens within 5 sec, except for NDV, which required 30 sec in the presence of organic materials. At 0.5X, PPMS successfully inactivated E. coli, AIV and NDV within 5 sec in the absence of organic material. However, rif-SI and SI necessitated 30 sec for inactivation. Most pathogens were inactivated within 30 sec, with the exception for AIV, which was inactivated within 5 sec. PPMS effectively eliminated rif-SI on all carriers within 30 sec. Moreover, at both concentrations, PPMS successfully inactivated AIV on all carriers within 30 sec, except on stainless steel at 0.5X. Furthermore, PPMS at both concentrations required 5 and 30 sec, respectively, to inactivate AIV on the rayon sheet. Therefore, due to its demonstrated efficacy against a wide range of pathogens across diverse surfaces, PPMS emerges as a crucial alternative disinfectant significantly enhancing biosecurity on and around chicken farms. found in and around animal farms, slaughterhouses, and hospitals.

Financial capacity instruments are psychometric tools designed to evaluate individual decisional capacity based on financial decisions. As tests are complex and need special conditions for administration and evaluation, it is difficult to use them in daily geriatric clinics. Our scoping review objective was to evaluate existing financial capacity instruments from the perspective of simplicity and portability. We evaluated one English speaking knowledge database (Medline) using a dedicated MeSH terminology. The review yielded one independent instrument, The Semi-Structured Clinical Interview for Financial Capacity, that can be easy adapted for every-day clinical use. It is simple to understand and perform and do not need trained personnel for administration. It can be finalized in 15 minutes. Initially validated on 261 subjects (with different forms of cognitive impairment), it showed good accuracy and precision mainly in subjects with cognitive impairment. The test is less apt to detect early or fluctuating cognitive impairment. Simplicity, the main advantage of the test, allows gamification fact that increases portability. Familiar images (coins, money) that are used for performing simple tasks does not need complex translation and adaptation. In form of a game, the test is suitable for serial administration, increasing the chance for early capacity reduction detection. Results reflect a physician judgement related to the subjects’ capacity to understand and execute simple financial instructions and not financial proficiency scores. The main limitation of our review is that we investigated only one, English speaking, knowledge database. The scoping strategy generated a financial capacity instrument that can be used in geriatric clinics for early diagnostic of decisional capacity reduction. Further studies are needed to evaluate the reliability and validity of the test in conditions of serial administration and in populations having various financial experience.

Over recent years, the swine industry has witnessed the withdrawal of antibiotics and continuous regulation of zinc and copper oxides in the early-life nutrition of piglets. Due to this development, alternative ingredients or additives from plant sources have been tremendously explored. Therefore, this study's objective was to evaluate the effect of dietary supplementation with tannins on weaned piglets’ growth performance, serum antioxidant capacity, and immune status using a meta-analysis approach. With only the inclusion of non-challenged weaned piglets, a total of 16 studies with parameters of interest were deemed eligible after a two-step screening process following a comprehensive literature search in the scientific databases of Web of Science, Scopus, ScienceDirect, PubMed, and Google Scholar. Two main categories of data, including the study’s characteristics and response variables (growth performance, serum antioxidant, and immune indices), were extracted. Applying the random-effects models, Hedges’ g effect size of supplementation with tannins was calculated using the R software to determine the standardized mean difference (SMD) at a 95% confidence interval. Sub-group analysis and meta-regression further explored heterogeneity (PSMD 0.05, I2 50%, n ≥10). Supplementation with tannin reduced average daily gain (p = 0.20) and feed conversion ratio (p 0.01); however, it increased average daily feed intake (p = 0.07) and final body weight (p 0.01). Meta-regression models indicated that tannin dosage and supplementation duration were directly associated with tannins' effectiveness on productive performance. In the serum, the concentration of glutathione peroxidase, superoxide dismutase, and total antioxidant capacity were elevated (p 0.01) in response to tannins supplementation, while malondialdehydes was reduced (p 0.01). Likewise, decreased immunoglobin A (p = 0.47) and increased immunoglobin M and G levels (p 0.01) were detected. In conclusion, dietary supplementation with tannins, particularly with chestnut and grape seed proanthocyanidins, increases the productivity of weaned piglets. At the same time, it is a possible nutritional strategy to mitigate oxidative stress and stimulate gut health. Thus, supplementing chestnut and grape seed proanthocyanidin tannins in the early phase of swine production could be used to alleviate the incidence of diarrhea.

One-dimensional chain of core-shell pairs connected by ideal springs enables design of the metamaterial demonstrating the negative effective density and negative specific thermal capacity. We assume that the molar thermal capacity of the reported metamaterial is governed by the Dulong-Petit law in its high temperature limit. The specific thermal capacity depends of the density of the metamaterial; thus, it is expected to be negative, when the effective density of the chain is negative. The range of the frequencies enabling the effect of the negative thermal capacity is established. Dependence of the effective thermal capacity on the exciting frequency for various core/shell mass ratios is elucidated. The effective thermal capacity becomes negative in the vicinity of the local resonance frequency ω0 in the situation when the frequency ω approaches ω0 from above. The effect of the negative effective thermal capacity is expected in metals in the vicinity of the plasma frequency.

The service conditions of underground coal mine equipment are poor, and it is difficult to accurately extract the fault characteristics of rolling bearings. In order to better improve the accuracy of fault identification of rolling bearings, a fault detection method based on multiscale permutation entropy and SOA-SVM is proposed. First, the whale optimization algorithm is used to select the modal analysis number K and the penalty factor α of the variational mode decomposition algorithm. Then, the vibration signal of rolling bearings is dissolved according to the optimized variational mode decomposition algorithm, and the multi-scale permutation entropy of the main intrinsic mode function is calculated. Finally, the feature values of the matrix are entered into the SVM algorithm optimized by the seagull optimization algorithm to obtain the classification result. The experimental results based on the published rolling bearing datasets of Western Reserve University show that the identification success rate of the proposed method can reach 98.75%. The fault detection of the rolling bearings can be completed accurately and efficiently.

Condition monitoring of bearings is an open issue. The use of the stator current to monitor induction motors has been validated as a very advantageous and practical way to detect several types of faults. Nevertheless, for bearing faults the use of vibrations or sound generally offers better results in the accuracy of the detection although with some disadvantages related to the sensors used for monitoring. To improve the performance of bearing monitoring, it is proposed to take advantage of more information available in the current spectra, beyond the usually employed, incorporating the amplitude of a significant number of sidebands around the first eleven harmonics, growing exponentially the number of fault signatures. This is especially interesting for inverter-fed motors. But, in turn, this leads to the problem of overfitting when applying a classifier to perform the fault diagnosis. To overcome this problem, and still exploit all the useful information available in the spectra, it is proposed to use shrinkage methods, which have been lately proposed in machine learning to solve the overfitting issue when the problem has much more variables than examples to classify. A case study with a motor is shown to prove the validity of the proposal

The dissolution of Al2O3 non-metallic inclusions from slag containing FexO was investigated in this study. The slag system used in the experiments was a quaternary system of CaO-SiO2-Al2O3-FexO. The composition of the slag was studied by fixing the basicity (CaO/SiO2 ratio) to 1 and varying the FexO content to 10 and 20wt%. In addition, the experimental temperature was varied as 1550℃, 1575℃, and 1600℃ to study the effect of temperature on the Al2O3 dissolution behavior. The experimental equipment is a single hot thermocouple apparatus. The dissolution rate of Al2O3 particles increased linearly with increasing temperature and FexO content. In addition, the mass transfer activation energy of Al2O3 dissolution in FexO 10wt% and FexO 20wt% was calculated by an Arrhenius type analysis. The obtained mass transfer activation energies were 159 and 189 kJ/mole, respectively.

Nitride and carbide are the second phases which play an important role in the performance of bearing steel, and their precipitation behavior is complicated. In this study, TiN-MC_x precipitations in GCr15 bearing steels were obtained by non-aqueous electrolysis, and their precipitation mechanisms were studied. TiN is the effective heterogeneous nucleation site for Fe₇C₃ and Fe₃C, therefore, MC_x can precipitate on the surface of TiN easily, its chemistry component consists of M₃C and M₇C₃ (M = Fe, Cr, Mn) and Cr₃C₂. TiN-MC_x with high TiN volume fraction, TiN forms in early stage of solidification, and MC_x precipitates on TiN surface after TiN engulfed by the solidification advancing front. TiN-MC_x with low TiN volume fraction, TiN and MC_x form in late stage of solidification, TiN can not grow sufficiently and is covered by a large number of precipitated MC_x particles.

In recent years, polyureas with dynamic hindered urea bonds (HUBs), as a class of promising biomedical polymers, have attracted attention as a benefit of their controlled hydrolytic property. The effect of the chemical structures on the properties of polyureas and their assemblies was rarely reported. In this study, four kinds of polyureas with different chemical groups have been synthesized, and the polyurea from cyclohexyl diisocyanate and tert-butyl diamine showed the fastest hydrolytic rate. The amphiphilic polyurea composed of hydrophobic cyclohexyl-tert-butyl polyurea and hydrophilic poly(ethylene glycol) was synthesized for controlled delivery of antitumor drug paclitaxel (PTX). The PTX-loaded PEGylated polyurea micelle more effectively entered into the murine breast cancer 4T1 cells and inhibited the corresponding tumor growth in vitro and in vivo. Therefore, the PEGylated polyurea with adjustable degradation might be a promising polymer matrix for drug delivery.

The availability of current land cover and land use (LCLU) information for monitoring the status of land resources has considerable value in ensuring sustainable land use planning. Similarly, the need to provide updated information on the extent of LCLU change in West Africa has become apparent, given the increasing demand for land resources driven by the rapid population growth in the sub-region. SERVIR West Africa, a regional consortium jointly supported by USAID and NASA to foster the use of geospatial and earth observation data and science for decision-making on critical environmental and food security challenges, in collaboration with the Food and Agriculture Organization of the United Nations (FAO), is building technical capacity in the sub-region to develop and implement harmonized regional land cover classification system for LULC change monitoring in West Africa, based on the Land Cover Meta Language (LCML-ISO 19144-2). This article focuses on the process, potential opportunities, outputs of this collaboration, exemplary use cases, and recommendations for the next steps.

A series of polynuclear, dinuclear, and mononuclear Mo(VI) complexes were synthesized with the hydrazonato ligands derived from 5-methoxysalicylaldehyde and the corresponding hydrazides (isonicotinic hydrazide (H2L1), nicotinic hydrazide (H2L2), 2-aminobenzhydrazide (H2L3) or 4-aminobenzhydrazide (H2L4)). The metallosupramolecular compounds obtained from non-coordinating solvents, [MoO2(L1,2)]n (1 and 2) and [MoO2(L3,4)]2 (3 and 4), formed infinite structures and metallacycles, respectively. By blocking two coordination sites with cis-dioxo ligands, the molybdenum centers have three coordination sites occupied by the ONO donor atoms from the rigid hydrazone ligands and one by N atom of pyridyl or amine-functionalized ligand subcomponents from the neighbouring Mo building units. The reaction in methanol afforded the mononuclear analogues [MoO2(L1-4)(MeOH)] (1a-4a) with additional monodentate MeOH ligand. All isolated complexes were tested as catalysts for cyclooctene epoxidation using tBuOOH (TBHP) as an oxidant in water. The impact of the structure and ligand lability on the catalytic efficiency in homogeneous cyclooctene epoxidation was elucidated through theoretical considerations. Thus, dinuclear assemblies exhibited better catalytic activity than mononuclear or polynuclear complexes.

The study’s objective was to evaluate the influence of thinning on the quality and regularity of yield of 'Regina' cherries grown on a dwarf Gisela 5 rootstock. The experiments were conducted in the years 2009-2012 in Western Poland. Trees were thinned using a chemical agent, ammonium thiosulphate (ATS) at doses of 20g ATS × L-1, 30g ATS × L-1 and 40g ATS × L-1, and by hand, and the results of chemical and hand thinning were compared with those obtained for unthinned trees. The course of weather conditions in winter and during flowering had a significant impact on yield. Chemical thinning is known to be an effective method to regulate fruiting of pome trees, but it can also be successful if applied to cherry trees, as reflected by the alternate bearing index, which was the lowest after applying ATS at a dose of 40g. ATS treatment improved fruit quality in full crop years. Thinning resulted in, among other things, larger and darker fruit and higher content of total soluble solids and titratable acidity. Treatment with 40g ATS × L-1 significantly stimulated the vegetative growth of trees.

Optical networks, characterized by using optical fibers as a transmission medium, constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is one of the key factors influencing optical network performance, it is important to comprehend its limitations and have the capability to estimate its value. In this context, we revisit the concept of capacity from various perspectives, including channel capacity, link capacity, and network capacity, thus providing an integrated view of the problem. Hence, we review the fundamental concepts behind optical networks, along with the basic physical phenomena present in optical fiber transmission and provide methodologies for estimating the different types of capacities, mainly using simple formulations. In particular, we propose a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with capacitated routing techniques for traffic routing. We apply this method to three reference networks and obtain capacities ranging from tens to hundreds of Terabits/s. Whenever possible, we also compare our results with published experimental data to understand how they relate.

The Sanaga River Valley is a deep-seated structure of about 220 km in width, bounded on its northern and southern sides by 025-0550 fault zones. Its internal structure has been very little described before this study. It is characterized by the presence of surface features where a thick stratum of shale and argillaceous sandstones have been documented. The use of electrical resistivity tomography for near-surface imaging and hydrogeological prospecting within shale succession is widespread. However, several methods of spatial modeling of resistivity contours are generally proposed for the interpretation of inverse resistivity model sections. To determine the most appropriate method for interpreting resistivity tomographies in the context of subsoil marked by significant heterogeneity, logarithmic contour intervals, and linear contour interval processing were implemented on data collected over five areas. The data consists of outcrops data, cuttings samples from groundwater boreholes, and resistivity sections ranging in length from 240 to 1000 m. Well-control of the inverse resistivity model sections derived from both processes shows that the linear contour intervals modeling gives a more realistic picture of the reservoir size of the wa-ter-bearing sand in both shale and argillaceous sandstone succession. The sedimentary architecture over Sanaga fault breccia is marked by vertical intrusion anomalies up to 80 m high. The shape of these anomalies, as well as the very low resistivity values that characterize them, suggests that they could be related to mud intrusion.

Vibration signal analysis is regarded as a fundamental approach in diagnosing faults in rolling bearings, and recent advancements have shown notable progress in this domain. However, the presence of substantial background noise often results in the masking of these fault signals, posing a significant challenge for researchers. In response, an Adaptive Denoising Autoencoder (ADAE) approach is proposed in this paper. The data representations are learned by the encoder through convolutional layers, while the data reconstruction is performed by the decoder using deconvolutional layers. Both the encoder and decoder incorporate adaptive shrinkage units to simulate denoising functions, effectively removing interfering information while preserving sensitive fault features. Additionally, dropout regularization is applied to sparsify the network and prevent overfitting, thereby enhancing the overall expressive power of the model. To further enhance ADAE's noise resistance, shortcut connections are added. Evaluation using publicly available datasets under scenarios with known and unknown noise demonstrates that ADAE effectively enhances the signal-to-noise ratio in strongly noisy backgrounds, facilitating accurate diagnosis of faults in rolling bearings.

This study addresses the critical issue of dowel-bearing strength in Bambusa blumeana, a key sus-tainable construction material crucial for climate change mitigation. Given the lack of bamboo connection standards, the research focuses on determining the dowel-bearing strength of Bambusa blumeana, emphasizing factors such as dowel diameter, node placements, and the physical prop-erties of bamboo. A predictive equation is derived, enhancing the practicality of bamboo in struc-tural design. The results underscore a notable correlation between dowel diameter and character-istic strength, with implications for engineering practices. Node placements significantly affect dowel-bearing capacity, while bamboo's physical attributes, including thickness, culm diameter, and moisture content, exhibit modest correlations with strength. The derived equation aims to assist in structural design, mitigating splitting and bearing failures in bamboo structures. This research establishes a foundation for optimizing the use of Bambusa blumeana in sustainable construction, advancing the understanding of its dowel-bearing strength for improved sustainability and resili-ence in the construction industry. Future research suggestions include exploring bamboo-mortar composites, additional node placements, and employing more comprehensive empirical equations and curve-fitting techniques. The study advocates for further investigations with more diverse and larger bamboo samples to bolster robustness. Additionally, delving into bamboo ductility may offer valuable insights.

A flexible structure is applied to improve the lubrication performance of a misaligned journal bearing. The journal bearing is representative sliding bearing and there are damages due to metal-to-metal contact by misalignment. Since misalignment is an unavoidable phenomenon, a journal bearing with a flexible structure was proposed as a way to improve it. The lubrication characteristics of the bearing are evaluated numerically under steady-state condition. EHL (elastohydrodynamic lubrication) analysis considering elastic deformation was performed. The lubrication performance is compared in accordance with variation of the geometry of the flexible structure and evaluated based on the minimum film thickness. Moreover, the results of the journal bearing with flexible structure are compared with those of the journal bearing without the flexible structure. The flexible structure is then applied in the form of a groove to the area supporting high load on the journal bearing; it is elastically deformed by the generated oil-film pressure, which helps to obscure a larger oil film. Through numerical analysis, it is found that the journal bearing with flexible structure can improve the lubrication performance in the misaligned condition.

Motivated by the way animals react in nature, we introduce a fully-connected neural-network model, which incorporates the external pattern presented to the system as a fundamental tool of the recognition process. In this new scenario, in the absence of this external field, memories are not attractors inside basins of attraction, as in usual attractor neural networks, although basins may be created according to the external pattern, thus allowing storing a much larger number of memories. The key point consists in calibrating the influence of the external pattern such as to cancel the noise generated by those memories not correlated with the external pattern.We illustrate how this proposal works by including this new contribution in the standard Hopfield model, showing a significant increase in its recognition capacity (typically by a factor $10^{2}$). As an additional feature of this model, we show its ability to react promptly to changes in the external environment, a crucial attribute of living beings. This procedure can be applied to a wide variety of neural-network models to increase considerably their recognition and reaction capabilities.

Propolis is a bee product widely used as a dietary supplement and included in sweets or baby foods due to its well-known antioxidant and nutritional properties that are directly correlated with its phenolic composition. For this reason, this study analysed the total contents of flavones and flavonols, flavanones and dihydroflavonols, and the antioxidant capacity by using the methods of ABTS and linoleic acid/β-carotene in 99 samples of propolis from Spain and Chile. A rapid method was developed for quantifying these parameters in raw propolis using near infrared (NIR) spectroscopy with an optical fibre probe of remote reflectance applied directly to the ground up sample. The models developed allow the determination of the total of flavones and flavonols (0-183 mg rutin/ g propolis), of the total of flavanones and dihydroflavonols (9-109 mg pinocembrin/ g propolis extract), and the antioxidant capacity by the ABTS method (0-3212 nmolesTrolox/ mg of propolis) and of linoleic acid/β-carotene (22-86% inhibition). The NIR spectroscopy models were applied in external validation to different samples of the calibration group, which led to the conclusion that the methods developed provide significantly identical data to the initial chemical data of reference.

Blind deconvolution (BD) is one of the effective methods that help pre-process vibration signals and assist in bearing fault diagnosis. Currently, most BD methods design an optimization criterion and use frequency or time domain information independently to optimize a deconvolution filter. It recovers weak periodic impulses related to incipient faults. However, the random noise interference may cause the optimizer to overfit. The time-domain-based BD methods tend to extract fault-unrelated single peak impulse, and the frequency-domain-based BD methods tend to retain the maximum energy frequency component, which will lose the fault-related harmonics frequency components. To solve the above issue, we propose a hybrid criterion that combines the kurtosis for time domain optimization and the $G-l_1/l_2$ norm for the frequency domain. These two criteria are monotonically increasing and decreasing, so they mutually constrain to avoid overfitting. After that, we design a multi-task one-dimensional convolutional neural network with time and frequency branches to achieve an optimal solution for this hybrid criterion. The multi-task neural network realizes the simultaneous optimization of two domains. Experimental results show that our proposed method outperforms other state-of-the-art methods.

The purpose of feature selection is to find important features from the original high-dimensional space. As atypical feature selection algorithm, Locally linear embedding(LLE)-based feature selection algorithm, which applies the idea of LLE to the graph-preserving feature selection framework, has been received wide attention. However, LLE-based feature selection framework is sensitive to noise and K-nearest neighbors. To address these problems, an improved LLE-based feature selection algorithm, robust LLE (RLLE) vote, is proposed. In this algorithm, $l_1$ and $l_2$ regularization are introduced into the high-dimensional reconstruction model of LLE. Furthermore, RLLE vote also proposes a criterion to measure the difference between the reconstruction features and the original features, and then the importance features can be selected by this criteria. Extensive experiments are carried out on a benchmark fault data set and the bearing data set collected from our own laboratory, and the experimental results demonstrate that RLLE vote achieves the most significant performance compared existing state-of-art methods.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

Quercetin is a flavonoid with a low molecular weight that belongs to the human diet's phenolic phytochemicals and non-energy constituents. Quercetin has a potent antioxidant capacity, being able to capture Reactive Oxygen Species (ROS), reactive nitro-gen species (RNS), and Reactive Chlorine Species (ROC), which act as reducing agents by chelating transition metal ions. Its structure has five functional hydroxyl groups, which work as electron donors and are responsible for capturing free radicals. In addition to its antioxidant capacity, it was described different pharmacological properties of Quercetin, such as carcinostatic properties, antiviral, antihypertensive, anti-inflammatory, protection of Low-Density Lipoprotein (LDL) oxidation, and inhibi-tion of angiogenesis are developed in this review.

This paper has two objectives: the first, to analyze the mediating effect of teacher empowerment between innovation culture and innovation capacity, and between inclusive leadership and innovation capacity; the second, to analyze the moderating effects of the school context on the innovation capacity. Data were collected in a representative sample of secondary schools in Valencia, Spain. The research model adopted is structural equation modeling, using the partial least squares (PLS) technique. The model has confirmed that teacher empowerment mediates between innovation culture and innovation capacity and between inclusive leadership and the innovation capacity. It is found that the educational context does not moderate the relationships in the proposed analysis model. This paper emphasizes the role of teacher empowerment in educational innovation and extends the knowledge of culture and leadership in the school organization.

Gastrointestinal tumors including pancreatic and colorectal cancers represent one of the greatest public health issues worldwide, leading to million global deaths. Recent research demonstrated that the human heavy chain ferritin (HFt) can encapsulate different type of drugs in its cavity and can bind to its receptor, CD71, in several solid and hematological tumors, thus highlighting the potential use of ferritin for tumor-targeting therapies. Here, we describe the development and characterization of a novel nanomedicine based on the HFt that is named The-0504. In particular, this novel system is a nano-assembly comprising an engineered version of HFt that entraps about 80 molecules of a potent, wide-spectrum, non-camptothecin topoisomerase I inhibitor (Genz-644282). The-0504 can be produced by a standardized pre-industrial process as a pure and homogeneously formulated product with favourable lyophilization properties. The preliminary anticancer activity was evaluated in cultured cancer cells and in a mouse model of pancreatic cancer. Overall results reported here make The-0504 a candidate for further preclinical development against CD-71 expressing deadly tumors

In this study one of the most innovative sintering techniques up to date was evaluated: Electro-Sinter-Forging (ESF). Despite it has been proved to be effective in densifying several different metallic materials and composites, bearing steels such as 100Cr6 have never been processed so far. Pre-alloyed Astaloy CrM powders have been ad-mixed with either graphite or graphene and then processed by ESF to produce a 100Cr6 equivalent composition. Porosity has been evaluated by optical microscopy and compared to that one of 100Cr6 commercial samples. Mechanical properties such as hardness and transverse rupture strength were tested on samples produced by employing different process parameters and then submitted to different treatments (machining, heat treatment). The experimental characterization highlighted that porosity is the factor mostly affecting mechanical resistance of the samples, correlating linearly to the transverse rupture strength. Hardness on the other side does not correlate to the mechanical resistance because process related cracking has a higher effect on the final properties. Promising results were obtained that give room to the sinterability by ESF of materials difficult to sinter by conventional press and sinter techniques.

Microbiome research has gained considerable interest due to the emerging evidence of its impact on human and animal health. Similar to higher organisms, the gut-associated microbiota of mosquitoes affect host fitness and other phenotypes. It is now well established that microbes can alter pathogen transmission in mosquitoes, either positively or negatively, and avenues are being explored to exploit microbes for vector control. However, less attention has been paid to how microbiota affect phenotypes that impact vectorial capacity. Several mosquito and pathogen components, such as vector density, biting rate, survival, vector competence and pathogen extrinsic incubation period all influence pathogen transmission. Interestingly, the mosquito gut-associated microbes can impact each of these components, and therefore ultimately modulate vectorial capacity. Promisingly, this expands the options available to exploit microbes for vector control by also targeting parameters that affect vectorial capacity. However, there are still many knowledge gaps in the biology of the mosquito – microbe symbiosis that need to be addressed in order to understand these interactions more thoroughly and exploit them efficiently. Here, we review current evidence of the impacts of the microbiome on aspects of vectorial capacity highlighting opportunities for novel vector control strategies and areas where further studies are required.

An increasing body of evidence shows that seaweeds, including kelp, can be used as a tool to neutralize or remove excess nutrients and metals from the water column. Here we report on a preliminary field assessment showing potential nutrient and carbon removal differences by sugar kelp and ribbon kelp grown in common gardens. Seawater and tissue samples were collected systematically from two farms in Alaska. Results show differences between % N and % C content between ribbon kelp (Alaria marginata) and sugar kelp (Saccharina latissima). Results also show that tissue nitrogen in ribbon kelp varies sharply due to nitrogen availability in the water column. In contrast, the percentage of tissue N in sugar kelp remains comparatively stable. Our outcomes provide insight into potential differences in nutrient removal and harvest timing for different kelp species.

This review covers the last 25 years literature on analogs of suberoylanilide hydroxamic acid (SAHA, known also as Vorinostat) acting as HDAC inhibitor. In particular, the topic has been focused on the synthesis and biological activity of compounds where the phenyl group (the surface recognition moiety, CAP) of SAHA has been replaced by an azaheterocycle through a direct bond with amide nitrogen atom, and the methylene chain in the linker region is of variable length. Most of the compounds reported displayed good to excellent inhibitory activity against HDACs and in many cases showed anti-proliferative activity against human cancer cell lines.

The vibration signal of the engine contains strong background noise and many kinds of modulating components, which is difficult to diagnose. Variational mode decomposition (VMD) is a recently introduced adaptive signal decomposition algorithm with a solid theoretical foundation and good noise robustness compared with empirical mode decomposition (EMD). VMD can effectively avoid endpoint effect and modal aliasing. However, VMD cannot effectively eliminate the random noise in the signal, so the random decrement technique is introduced to solve the problem. Based on the crankshaft bearing fault simulation experiment, the four kinds of wear state vibration signals are decomposed by VMD, and the modal components with smaller permutation entropy are selected as fault components. Then the fault component is processed by the random decrement technique, and the Hilbert envelope spectrum of the fault component is obtained. Compared with the fault feature extraction method based on EMD and EEMD, the feature extraction results of the proposed method are better than those of the above two methods. The simulation analysis and the simulation test of the crankshaft bearing fault verify the effectiveness of the proposed method.

This paper presents the results of an experimental and analytical study on the behavior of cold-formed thick-walled steel plates connected by a single bolt under double shear. Experimental studies were conducted on a total of 54 bolted connections fabricated from two thickness of cold-formed thick-walled steel plates with the nominal thickness of 6 mm and 10 mm. The effects of end distance, edge distance and steel plate thickness were investigated on the bolt bearing behavior. Codes of (modified) ANSI/AISC 360-16 and EN1993-1-8 were applied to predict failure modes and bearing resistance of connections and the predictions were compared with that of measurements. A method was proposed to calculate the elongation of bolt hole at ultimate load. The studies show that fractures occurred on shear planes of specimens failed by shear out due to reduced ductility caused by cold forming process. The modified ANSI/AISC gives the most accurate predictions of failure modes and bearing resistance. However, the bearing resistance will be overestimated if the reduction in area of shear planes caused by occurrence of fracture is ignored for specimens with end distance being higher than 2.0d0 and a reduction factor is needed for calculating bearing resistance of connections. The method proposed in our paper can predict the elongation of bolt hole very well.

This paper realizes early bearing fault warning through bearing fault time series prediction, and proposes a bearing fault time series prediction model based on optimized maximum correlation kurtosis deconvolution (MCKD) and long short-term memory (LSTM) recurrent neural network to ensure bearings operation reliability. The model is based on lifecycle vibration signal of the bearing, to begin, the cuckoo search (CS) is utilized to optimize the parameter filter length L and deconvolution period T of MCKD, taking into account the influence and periodicity of the bearing time series, the fault impact component of the optimized MCKD deconvolution time series is improved. Then select the LSTM learning rate α depending on deconvolution time series. Finally, the dataset obtained through various preprocessing approaches are used to train and predict the LSTM model. The average prediction accuracy of the optimized MCKD-LSTM model is 26 percent higher than that of the original time series, proving the efficiency of this method, and the prediction results track the real fault data well, according to the XI'AN JIAOTONG University XJTU-SY bearing dataset.

In this paper, we introduce the Prognostics and Health Management of gear bearing system using autoencoder neural networks. Bearings and gears are the most common mechanical components in rotating machines, and their health conditions are of great concern in practice. This study presents an outlier modeling method for forecasting the gear bearing system failure using the health indicators constructed from mechanical signal processing and modeling. Outlier modeling aims to find patterns in data that are significantly different from what is defined as normal. In the unsupervised outlier modeling setting, prior labels about the anomalousness of data points are not available. In such cases, the most common techniques for scoring data points for outlyingness include distance-based methods density-based methods, and linear methods. The conventional outlier modeling methods have been used for a long time to detect anomalous observations in data. However, this paper shows that autoencoders are a very competitive technique compared to other existing methods. The developed method is demonstrated using the IMS bearing data from NASA Acoustics and Vibration Database.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

The prevention, mitigation and treatment of movement impairments, ideally, requires early diagnosis or identification. As the human movement system has physiological and functional redundancy, movement limitations do not promptly arise at the onset of physical decline. A such, prediction of movement limitations is complex: it is unclear how much decline can be tolerated before movement limitations start. Currently, the term ‘homeostatic reserve’ or ‘physiological reserve’ is used to refer to the redundancy of the human biological system, but these terms do not describe the redundancy in the muscle architecture of the human body. The result of functional redundancy is compensation. Although compensation is an early predictor of movement limitations, clear definitions are lacking and the topic is underexposed in literature. The aim of this article is to provide a definition of compensation and emphasize its importance. Compensation is defined as an alteration in the movement trajectory and/or altering muscle recruitment to complete a movement task. Compensation for capacity is the result of a lack in neuromusculoskeletal reserve, where reserve is defined as the difference between the capacity (physiological abilities of the neuromusculoskeletal system) and the task demand. Compensation for movement objectives is a result of a shift in weighting of movement objectives, reflecting changing priorities. Studying compensation in biomechanics requires altered protocols in experimental set-ups, musculoskeletal models that are not reliant on prescribed movement, and inclusion of alternative movement objectives in optimal control theory.

Africa, home to the world's second-largest population of approximately 1.3 billion, grapples with significant challenges in meeting its medical needs, particularly in accessing quality healthcare services and products. The continent faces a continuous onslaught of emerging infectious diseases, exacerbating the strain on its already fragile public health infrastructure. The emergence of SARS-Cov2 has further exposed the deficiencies in Africa's public health response, ranging from limited diagnostic capabilities to difficulties in vaccine distribution. Compounding these challenges is vaccine hesitancy, which is prevalent in many regions due to varying levels of understanding and trust regarding vaccines. The disparities in vaccine literacy across the continent stem from a complex interplay of factors, including low literacy rates and a history of medical exploitation and misinformation campaigns. These factors have led to a pervasive distrust in medical institutions and healthcare providers among certain African communities. Despite concerted efforts by national governments, private entities, and international partners to address these challenges and improve vaccine literacy, significant hurdles persist. This manuscript examines the current state of education in vaccinology and related sciences in Africa, as well as the continent's efforts to address educational needs in vaccine development and manufacturing. It evaluates initiatives aimed at strengthening vaccine education and literacy, highlighting successful approaches and ongoing challenges. By assessing the progress made and identifying remaining obstacles, this review offers insights into how Africa can enhance its capacity in vaccinology and accelerate its contributions to global health security.

The fault diagnosis of the gearbox is primarily based on the analysis of the harmonic response. However, the generation mechanism of the harmonic response of the gear pair is still not distinctly explained in a healthy gearbox. Therefore, this paper is dedicated to establishing a dynamic model of the gearbox for this issue. In this model, the contact force of the bearing and the meshing stiffness of the gear pair are determined by the Hertz theory and the potential energy method, then the shaft motion is used as the connection to establish the coupling relationship between the gear pair and the bearing. After this dynamic model is confirmed by experiments and existing models, the coupling relationship inside the gearbox and the harmonic response of the gear pair are studied using this model. The result demonstrates that a closed control loop is formed due to the vibration transmission between the gear pair, the bearing and the shaft, and there is a strong coupled vibration between the gear pair and the bearing in the gearbox. Due to the generation of the center distance error, misalignment angle and disorganized meshing process of the gear pair, the meshing stiffness is altered, which excites the harmonic response of the gear pair. When the speed of the gearbox is increased, although the vibration amplitude of the gearbox is increased, the system predominantly vibrates at the fundamental frequency, and the harmonic of the gear pair is also shifted to the low frequency band.

Past exploration for U deposit in the Philippines discovered the mineralization of radioactive allanite in Palawan. The allanite occurs as sand component in the heavily populated beach of Erawan, San Vicente, Palawan. This work assessed the risks associated with the radionuclides in Erawan beach by in situ ground radiometric survey of K, U, and Th in 694 sampling points. Principal component analysis (PCA) and Pearson correlation coefficient were used to determine the similarity between the radionuclides and to identify other probable anthropogenic sources of radionuclides. Our results show that the mean activity concentrations of K (597.8 Bq kg^-1) and Th (93.15 Bq kg^-1) are equivalent to 1.5 and 3.1 times of the world average natural radioactivity levels in soil, respectively, while the mean U (34.7 Bq kg^-1) is similar to the world average. The mean radiological risk assessments like radium equivalent, gamma specific activity index, external hazard index, internal hazard index, absorbed gamma dose rate, annual effective dose equivalent, annual gonadal equivalent dose, and excess lifetime cancer risk are 213.96 Bq kg^-1, 0.78, 0.58, 0.67, 97.24 nGy h^-1, 119.25 µSv y^-1, 684.39 µSv y^-1, and 0.42 (10^-3), respectively. Th consistently correlated most to the risks. We attribute the occurrence of Th to the presence of allanite, K to fertilizer use for farming, and U to both the allanite and farming. The results of our study can provide important baseline data for future detailed studies or monitoring of the long-term effects of elevated radiation levels to the local population of Erawan.

Photodynamic therapy (PDT) has garnered significant attention in the fields of cancer treatment and drug-resistant bacteria eradication due to its non-invasive nature and spatiotemporal controllability. Iridium complexes have captivated researchers owing to their tunable structure, exceptional optical properties, and substantial Stokes displacement. However, most of these complexes suffer from aggregation-induced quenching, leading to diminished luminous efficiency. In contrast to conventional photosensitizers, photosensitizers exhibiting aggregation-induced luminescence (AIE) properties retain the ability to generate a large number of reactive oxygen species when aggregated. To overcome these limitations, we designed and synthesized a novel iridium complex named Ir-TPA in this study. It incorporates quinoline triphenylamine cyclomethylated ligands that confer AIE characteristics for Ir-TPA. We systematically investigated the photophysical properties, AIE behavior, spectral features, and reactive oxygen generation capacity of Ir-TPA. The results demonstrate that Ir-TPA exhibits excellent optical properties with pronounced AIE phenomenon and robust capability for producing singlet oxygen species. This work not only introduces a new class of metal iridium complex photosensitizer with AIE attributes but also holds promise for achieving remarkable photodynamic therapeutic effects in future cellular experiments and biological studies.

eHealth applications are an essential component in achieving Universal Health Coverage. (1) Background: The lack of skilled healthcare personnel has hindered successful integration and use, especially in developing and low and middle-income countries. (2) Methods: A descriptive study was conducted using an online survey to collect quantitative data from 37 organizations to address this issue. (3) Results: The findings showed that there are limited training opportunities available for policymakers and eHealth specialists. Additionally, obstacles such as insufficient funds, inadequate infrastructure, poor leadership, and governance were identified and found to be context specific. To mitigate these challenges, the study proposed continuous in-service training, the implementation of computer-based systems, and the integration of academic modules. The importance of strong eHealth policies and committed leaders was also emphasized. (4) Conclusions: The results of this study support previous research and emphasize the importance of implementing practical and uncomplicated solutions to overcome eHealth barriers to capacity building in low- and middle-income countries. It is essential to recognize that the data collected for this study only pertains to BETTEReHEALTH.

Soy isoflavones are considered important sources of bioactive compounds, but they are poorly absorbable, due to their large hydrophilic structures. Some biotransformation strategies have been used to convert the glycosidic form into aglycones, making them available for absorption. This study evaluated the potential of enzymatic and/or microbial fermentation bioprocesses in soymilk extract before and after gastrointestinal in vitro digestion. Commercial β-glucosidase and mix of commercial probiotics containing Lactobacillus acidophilus, L. casei, Lactococcus lactis, Bifidobacterium bifidum e B. lactis were used to biotransform soymilk extract. Isoflavone profile was quantified by HPLC-DAD, total phenolic content by Folin–Ciocalteu test, and antioxidant capacity by ORAC and FRAP. Soymilk enzymatically treated (ET) followed by microbial fermentation (ET+F) resulted in the conversion of glycosylated isoflavones (6-fold lower than control for daidzin and 2-fold for genistin) to aglycones (18-fold greater than control for dadzein and genistein), besides to increase the total phenolic content (3.48 for control and 4.48 mg/ml ET+F) and to improve antioxidant capacity represented by the ORAC (120 for control and 151 mg/ml ET+F) and by the FRAP (285 for control and 317 µl/ml for ET+F) before in vitro digestion. Further, the digested ET+F samples resulted a higher content of genistein (2-fold higher than control) also an increase in the total phenolic content (2.81 for control and 4.03 mg/ml for ET+F) and antioxidant capacity by ORAC were greater compared to undigested samples. In addition, the microbial fermentation process isolated also resulted in the positive effects, but de combination of ET followed by F presented a synergistic effect, suggesting the greater potential for both bioprocesses to contribute to functional and nutritional properties on fermented soy-based products.

The coal mine underground reservoir is an appropriate solution between coal mining and groundwater resource protection and utilization. By calculating the storage capacity of a groundwater reservoir, the storage coefficient has been proved to be always an empirical value. Based on the mathematical derivation of the vertical fracture area ratio and the horizontal fracture area rate of the collapse zone and the fissure zone in the goaf area of the coal seam, the mathematical models of tem are derived, and the model for calculating the water storage coefficient is derived. The water storage coefficient derived from the theoretical model had more basis and more advanced than the traditional empirical value. By using this method, the practical calculation of No.1 underground reservoir of the DaLliuta Coalmine in Shenhua Shendong, has got a perfect matching with the actual groundwater storage capacity.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

Grinding processes’ stochastic nature poses a challenge in predicting the quality of the resulting surfaces. Post-production measurements for form, surface roughness, and circumferential waviness are commonly performed due to infeasibility in measuring all quality parameters during the grinding operation. Therefore, it is challenging to diagnose the root cause of quality deviations in real-time resulting from variations in the machine’s operating condition. This paper introduces a novel approach to predicting the overall quality of the individual parts. The grinder is equipped with sensors to implement condition-based maintenance and is induced with five frequently occurring failure conditions for the experimental test runs. The crucial quality parameters are measured for the produced parts. Fuzzy c-means (FCM) and Hotelling’s T-squared (T2) have been evaluated to generate quality labels from the multi-variate quality data. Benchmarked random forest regression models are trained using fault diagnosis feature set and quality labels. Quality labels from the T2 statistic of quality parameters are preferred over FCM approach for their repeatability. The model, trained from T2 labels achieves more than 94% accuracy when compared to the measured ring disposition. The predicted overall quality using the sensors’ feature set is compared against the threshold to reach a trustworthy maintenance decision.

In recent years, intelligent fault diagnosis algorithms using deep learning method have achieved much success. However, the signals collected by sensors contain a lot of noise, which will have a great impact on the accuracy of the diagnostic model. To address this problem, we propose a one-dimensional convolutional neural network with multi-scale kernels (MSK-1DCNN) and apply this method to bearing fault diagnosis. We use a multi-scale convolution structure to extract different fault features in the original signal, and use the ELU activation function instead of the ReLU function in the multi-scale convolution structure to improve the anti-noise ability of MSK-1DCNN; then we use the training set with pepper noise to train the network to suppress overfitting. We use the Western Reserve University bearing data to verify the effectiveness of the algorithm and compare it with other fault diagnosis algorithms. Experimental results show that the improvements we proposed have effectively improved the diagnosis performers of MSK-1DCNN under strong noise and the diagnosis accuracy is higher than other comparison algorithms.

The high reliable correlations between CBR and DCP in general proposed are presented in this paper. We analyzed the test data and correlations from many researchers to find the best equation for prediction the CBR from DCP test. The findings show that all correlations from existing paper are based on local material and cannot apply to soil in a different location in general purpose. New correlations between CBR and DCP were proposed and validated in this paper for general uses. The validation confirmed that these new correlations can predict well with higher R2.

In this study, two donor-acceptor (D-A) type conjugated polymers namely PQSeCz and PQSeFl were designed and synthesized. Selenophene was incorporated as a π -bridge, quinoxaline as an acceptor unit while carbazole and fluorene were used as the donor units. Polymers were synthesized via palladium catalyzed Suzuki polymerization reaction. All molecules were characterized by 1H and 13C NMR Spectroscopy. The weight and number average molecular weights of the two polymers were determined by gel permeation chromatography (GPC). Electrochemical and spectroelectrochemical characterizations of the polymers were performed to investigate their optoelectronic properties. Oxidation potentials were 1.15 V/ 0.82 V and 1.11 V/ 0.82 V for PQSeCz and PQSeFl respectively, while reduction potentials were -1.26 V /-1.14 V and -1.48 V/ -1.23 V, respectively. In the visible region, maximum absorption wavelengths for the two polymers were 551 nm and 560 nm, respectively. Optical band gaps (Egop) were found from the lowest energy π – π∗ transition onsets as 1.71 eV and 1.58 eV, respectively. Both polymers showed good solubility in common solvents.

Nowadays, there is extensive production and use of plastic materials for different industrial activities. These plastics, either from their primary production sources or through degradation processes of the plastics themselves, can contaminate the ecosystem with micro and nanoplastics. Once in the aquatic environment, these microplastics can be the basis for the adsorption of chemical pollutants, favoring that these chemical pollutants disperse more quickly in the environment and can affect living beings. Due to the lack of information on adsorption, three machine learning models (random forest, support vector machine, and artificial neural network) to predict different microplastic/water partition coefficients (log Kd) were developed using two different approximations (based on the number of input variables). The best-selected machine learning models present, in general, correlation coefficients upper than 0.92 in the query phase, which indicate that these type of models could be used for a rapid estimation of the absorption of organic contaminants on microplastics.

One of the mechanisms used in the management and cure of atherosclerosis is reverse cholesterol transfer (RCT), which plays a vital role in the export of cholesterol from peripheral cells. Cholesterol efflux from macrophages in the subintima of the vessel wall is a critical part of RCT. ATP-binding cassette transporter A1 (ABCA1) and ATP-binding cassette transporter G1 (ABCG1) are involved in the transfer of cholesterol from arterial macrophages to extracellular high-density lipoprotein cholesterol (HDL). The HDL then transports esterified cholesterol to the liver for elimination. An important factor in the reverse cholesterol transport and excretion of extracellular cholesterol is HDL. Atherogenesis can be prevented by altering the processes of RCT and cholesterol efflux, and this might lead to novel treatment options for cardiovascular disease. Research of novel modifying variables for RCT and cholesterol efflux is necessary. A better understanding of RCT's molecular processes has been gained via research, allowing for the creation of new treatments that make use of RCT's potential for pharmacological improvement. The purpose of this review is to provoke discussion on the potential impact of selected flavonoids on cholesterol efflux on the progression of atherosclerosis (Fig. 1.).

Water is essential for living organisms. The increase in world population, global climate change and rapid growth in industrialization and urbanization have brought with them water issues around the world in recent years. Not only should existing water resources be used reasonably and efficiently but alternative water resources should also be explored and secured. Rainwater harvesting, which is one of the alternative water resources, can provide economic and environmental solutions. For rainwater harvesting, the size of reservoirs in which rainwater captured from roof catchments is stored should be determined. Determining the optimum tank capacity depending on precipitation and consumption rates allows us to make maximum use of rainwater tanks. The aim of this study is to determine the optimum tank capacity for the storage of rainwater captured from roof catchments in order to meet the water demand for agricultural production. Precipitation data were collected from the city of Isparta and its districts. Rainwater tank capacity was determined using the Rippl, residual mass curve, minimum flow and particle swarm optimization methods. Storage capacities varying according to roof areas and consumption rates are shown in a graph. Results show that particle swarm optimization is the best method.

A statistical analysis of semantic memory should reflect the complex, multifactorial structure of the relations among its items. Still, a dominant paradigm in the study of semantic memory has been the idea that the mental representation of concepts is structured along a simple branching tree spanned by superordinate and subordinate categories. We propose a generative model of item representation with correlations that overcomes the limitations of a tree structure. The items are generated through "factors" that represent semantic features or real-world attributes. The correlation between items has its source in the extent to which items share such factors and the strength of such factors: if many factors are balanced, correlations are overall low; whereas if a few factors dominate, they become strong. Our model allows for correlations that are neither trivial nor hierarchical, but may reproduce the general spectrum of correlations present in a data-set of nouns. We provide an estimate of the number of concepts that can be stored and retrieved by a large-scale cortical network, the Potts network, which is perhaps approximately 10⁷ with human cortical parameters. When this storage capacity is exceeded, however, retrieval fails completely only for balanced factors; above a critical degree of imbalance, a phase transition leads to a regime where the network still extracts considerable information about the cued item, even if not recovering its detailed representation: partial categorization seems to emerge spontaneously as a consequence of the dominance of particular factors, rather than being imposed ad hoc. We argue this to be a relevant model of semantic memory resilience in Tulving’s remember/know paradigms.

Alum sludge, an inevitable by-product from the water purification process, which had been applied as substrates in some constructed wetlands with good performance, especially for phosphorus (P) adsorption. The raw alum sludge is like clay lump with irregular shape and has a leaching concern used in the water. For a better reuse, herein, sludge was fired to produce alum sludge ceramsite (ASC) with a uniform spherical shape via four-step process of kneading sludge ball, air drying, preheating at 400°C for 10 min and firing at 600℃ for 5 min. Thereafter the physicochemical properties and P adsorption ability of ceramsite were investigated. Through XRD and FT-IR tests, there was no obvious difference between ASC and air-dried alum sludge ball (adASB) on the phase structure, but a certain amount of Al-OH group loss on the surface of ASC. The structure of ASC was still amorphous as same as adASB, while ASC possessed more micropore structure and bigger specific surface area than those of adASB. Adsorption experiments showed the P adsorption behaviors of ASC and adASB were much similar, and their adsorption kinetics all accorded with the two-step adsorption kinetics rate equation and pseudo-second-order kinetics equation. The maximum adsorption capacities of ASC and adASB fitted by Langmuir model were 1.66 mg/g and 1.89 mg/g respectively. It should be pointed that, compared with other adsorbents, ASC produced in this study still had a higher ability to adsorb P. Therefore, ASC should have a great application potential for P removal in the wastewater treatment in China.

There have been relatively few researches that determine the role of bricolage in mediating the empirical relationship between strategic flexibility and product innovation. However, most of the research has studied strategic flexibility to engage the absorptive capacity and facilitate product innovation. The Bricolage approach emphasizes utilizing existing resources in product innovation and explores the mechanisms behind bricolage. A resource-based approach to product innovation involves combining resources in the development process in a concrete manner. This is a groundbreaking study since it is the first to examine empirically how absorptive capacity affects product innovation through bricolage and the serial mediation of strategic flexibility. As a consequence of presenting our results, we concluded that absorptive capacity positively and significantly influences product innovation through the serial mediation of strategic flexibility and bricolage. For strategic flexibility to play a role in supporting product innovation, bricolage is one of the mechanisms that can be utilized. This study contributes to the literature on strategic flexibility by examining the effect of strategic flexibility on bricolage and product innovation from the standpoint that absorptive capacity enhances the strategic flexibility of high-tech SMEs in China. Furthermore, this research offers new insights into the relationship between absorptive capacity and product innovation. In addition, it also provides insight into the economic opportunities that may result from product innovation in transition economies such as China.

The intensive care units in North West London are part of one of the oldest critical carenetworks in the UK, forming a mature and established strategic alliance to shareresources, experience and knowledge for the benefit of its patients. North WestLondon saw an early surge in COVID-19 admissions, which urgently threatened thecapacity of some of its intensive care units even before the UK government announcedlockdown. The pre-existing relationships and culture within the network allowed itsmembers to unite and work rapidly to develop agile and innovative solutions, protectingany individual unit from becoming overwhelmed, and ultimately protecting its patients.Within a short 50-day period 223 patients were transferred within the network todistribute pressures. This unprecedented number of critical care transfers, combinedwith the creation of extra capacity and new pathways, allowed the region to continue tooffer timely and unrationed access to critical care for all patients who would benefitfrom admission. This extraordinary response is a testament to the power and benefitsof a regionally networked approach to critical care, and the lessons learned maybenefit other healthcare providers, managers and policy makers, especially in regionscurrently facing new outbreaks of COVID-19.

The concept of friction damper is widespread technique and used to reduce the structural vibrations in many industrial applications. These friction dampers are generally coated with low wear rate materials to reduce the fretting wear. This paper investigates the use of physical vapor deposition (PVD) nitride based AlTiN coating material applied over the stainless steel friction damper to enhance the damping capacity and to reduce the fretting wear. A friction test rig has been developed to measure the dynamic hysteresis characteristics of friction damper at high temperature (700 °C). The damping capacity and fretting wear analysis is carried out at room temperature, 300 °C and 600 °C. The force versus displacment characterisitcs curve is used to predict the damping capacity and fretting wear analysis is carried out at microscopic level for the comparision. It is observed that at room temperature AlTiN coated friction damper has not much influence to improve the damping capacity and to reduce the fretting-wear. However, at high temperature it has better damping capacity and less wear in comparision to uncoated friction damper. Wear behaviour in coated and uncoated damper is different at room temperature and at elevated temperature.

JIS SUJ2 is most widely used in bearing steels. The advantages are good hardenability, excellent fatigue, wear resistance and comprehensive mechanical properties. For wear resistance and fatigue resistance of the steel are getting more and more attention, the residual stress state and its distribution on the surface of the heat affect zone are critical factors affecting the fatigue life and wear resistance of the parts. In this study, using the SUJ2 as the material to talk about the surface residual stress and retained austenite distribution. Doing the quenching and tempering treatment to obtain different microstructures, using the induction method to re-quench the case region. After the heat treatment, measuring the residual stress and retained austenite volume on the surface by X-ray diffraction, observing the microstructure and comparing the hardness. The results show that the microstructure after heat treatment contains unsolidified carbides, tempered martensite and retained austenite. The residual stress on the surface is the tensile state. In the re-hardened area after induction quenching, the residual stress is all compressive, and the values are more than -800 MPa. In conclusion, in the same output power condition can be observed that the microstructure of the specimens before induction hardening has a significant impact on the effective case depth. The surface residual stress has changed from a tensile to a compressive state. In the re-hardened area, the maximum of the residual compressive stress increased with the austenitized temperature increase.

Platinum group metals (PGMs) high-grade ore tonnage from Merensky reef keeps on depreciating forcing the metallurgical industry to explore beneficiating PGMs from upper group 2 (UG2) ore which has up to 60% content of chromite and from secondary sources. The PGMs are naturally associated with base metal sulphides and the efficacy of the PGMs extraction processes is dependent on the processing of PGMs-bearing base metal sulphides. These processes include concentrating PGMs-bearing base metal sulphides through flotation, oxidation, etc. prior the metal extraction processes. The evolving mineralogy of PGMs ores has necessitated the use of multiple reagents to enhance the efficiency of the concentration process. This has led to an increased amount of inor-ganic chemicals disposal to the environment and the processing of PGMs to be less economic. Bio-technology has been investigated as a potential low cost, ecologically safe substitute for many current minerals processing methods. The metabolites produced by microorganisms have been used for many years with great success in the leaching and flotation of metals from medium and low-grade sulphide minerals. The possible application of microorganism mainly Acidithiobacillus ferrooxidans (A. ferrooxidans) in the metallurgical processing of PGMs-bearing base metal sulphides is systematically reviewed in this paper. The main emphasis is on the use of A. ferrooxidans in bio-oxidation and bioleaching, as well as their potential to substitute inorganic reagents in the flo-tation of PGMs-bearing base metal sulphides from primary and secondary sources

We study the short−term memory capacity of ancient readers of the original New Testament written in Greek, of its translations to Latin and modern languages. To model the short–term capacity, we have considered the number of words per interpunctions, the “word interval” , because this parameter can model how the human mind memorizes “chunks” of information. Since can be calculated for any alphabetical text, we can perform experiments − otherwise impossible − with ancient readers by studying the literary works they used to read. The “experiments” compare the of texts of a language/translation to those of another language/translation by measuring the minimum average probability of finding joint readers (those who can read both texts because of their similar short–-term memory capacity) and by defining an “overlap index”. We also define a population of universal readers who can read any the New Testament written in alphabetical language. More than 50% of the readers of specific languages overlap with the universal readers with probability . Future work is vast, with many research tracks, because alphabetical literatures are very large and allow many experiments, such as comparing authors, translations or even texts written by artificial intelligence tools.

China is a large agricultural country that produces a large amount of crop straw every year. Thus, the development of cost-effective and economic application of invasive plants is warranted. Biochars derived from crop straw has been proven to be promising for adsorbent materials. However, less studies have focused on biochar derived from different types of crop straw as adsorbent under the same conditions to compare their adsorption performance. Here, we characterized the five biochars in the same system (600 ℃). In results, GBC has higher ash content, pH, CEC, specific surface area, mineral composition and oxygen-containing functional groups. The adsorption kinetics can be explained adequately by pseudo-second-order model and Langmuir model, indicating that the adsorption behavior of the biochar is both physical adsorption and chemical adsorption, the adsorption process includes complexation reaction, cationic π bond, ion precipitation and electrostatic adsorption. In conclusion, GBC exhibited higher metal equilibrium adsorption capacities (125 mg·g-1 for Pb2+, 29 mg·g-1 for Cd2+). The solution pH, biochar dosing, pyrolysis temperature and the properties of these heavy metals were responsible for adsorption capacity, thus showing stronger affinity and better adsorption effect. Our results are important for the selection and utilization of plant-based biochar for different heavy metals.

(1) Background: The purpose of this study was therefore to analyze the predictive capacity of the three variables (impulsivity, sensation-seeking and drug use) in aggressors and victims of violence. (2) Methods: The design is cross-sectional quasi-experimental. A sample of 822 students aged 13 to 18 who had filled in an ad hoc questionnaire, the State Impulsivity Scale and the Sensation-Seeking Scale, was used for this. (3) Results: The results show that aggressors had high levels of gratification, automatism, attentional factor, disinhibition and susceptibility to boredom, and use alcohol and/or tobacco. The variables that could predict involvement as an aggressor in peer conflict are use of alcohol, smoking, high levels of gratification, automatism and attentional factors and a high degree of disinhibition and susceptibility to boredom. The disinhibition is the best predictor of aggressor. (4) Conclusions: Thus having available empirical evidence that facilitates detection of predictive variables for participation in violence is going to favor the design of effective education intervention for reducing risk behavior.

The current study aimed to investigate the antitumor effects and potent mechanism of cytokine-induced killer (CIK) cells combined with irreversible electroporation (IRE) via an in vitro function assay in an in vivo Panc02 cell–bearing mouse model. We established an in vitro culture assay for CIK cells and determined the proportions of different peripheral lymphocytes. The antitumor effect of the combination of IRE and CIK cells in a Panc02 pancreatic-cancer (PC) subcutaneous-xenograft model was investigated; tumor size and mouse survival rates were recorded. We used flow cytometry (FCM) to analyze the proportion of intratumoral lymphocytes, the expression of chemokine receptors, and the proliferative activity of CIK cells. The proportion of cells that were positive for clusters of differentiation 3 and 8 (CD3+CD8+) and the proportion of CD3+CD56+ cells were both significantly increased after 21 days of in vitro culture. Combined IRE/CIK cell treatment significantly inhibited tumor growth and increased the survival rate of Panc02 cell–bearing mice. Furthermore, infiltration of lymphocytes into tumor tissue was significantly increased by this combination therapy compared with the untreated group or monotherapy group. In addition, IRE significantly enhanced the expression of chemokine receptors elicited by, and the proliferative activity of, CIK cells. In conclusion, IRE combined with CIK cells showed superior antitumor efficacy in a PC subcutaneous-xenograft model, which we attributed to the promotion of lymphocytic infiltration, as well as to upregulation of chemokine receptor expression and of regulators of CIK cell proliferation.

Various studies have addressed the role of neutrophils in cancer wherein the focus has been drawn on the elevated neutrophil count in blood or at tumor loci. However, cancer has a systemic impact which targets various organs thus challenging the overall physiology of the host. So, it is worthwhile to explore whether and how neutrophils contribute to systemic deterioration in cancer. To discern the systemic role of neutrophils, we monitored their number and function at different stages of tumor growth in Dalton’s lymphoma mice model. Notably, we observed a gradual increase in neutrophil count in blood and their infiltration in vital organs of tumor bearing mice. In parallel, we observed damaged histoarchitecture with significant alterations in biochemical parameters that aggravated with tumor progression. We next examined systemic impact of neutrophil by assessing neutrophil elastase, myeloperoxidase, and matrix metalloproteinases (MMP-8 and MMP-9) wherein we found their upregulated expression and activity in tumor condition. Taken together, our results demonstrate high infiltration and hyperactivation of neutrophils which possibly account for gradual systemic deterioration during cancer progression. Our findings thus implicate neutrophils as a potential therapeutic target that may help to reduce the overall fatality rate of cancer.

As the most important component of soft robot, the pneumatic actuator can drive robot movement. However, the effect of the actuator pneumatic network geometry on the actuator load capacity is insufficient. In this paper, the finite element analysis method is applied to calculate the load force and stability torque of the pneumatic actuator under a wide range of length and height dimensions of the pneumatic network. The effect of the network size on the structure rigidity, load capacity and deformation of the actuator is analyzed. Based on the calculation results, the effect of network structure size on the deformation and load capacity is analyzed, and the optimal geometric results with the maximum load capacity are obtained. This study provides theoretical guidance for the structural design and optimization of the pneumatic actuator.

Myalgic Encephalomyelitis / Chronic Fatigue Syndrome (ME/CFS) is an acquired disease with significant morbidity that affects both children and adults. Effective tools to assess functional capacity (FC) are severely lacking which has significant consequences for timely diagnosis, assessments for patient disability benefits and assessing the impact and effectiveness of interventions. In interventional research the inability to assess FC can result in an incomplete assessment of the potential effect of the intervention. Specifically of concern is that if an intervention is effective in reducing symptom load, patients may increase their activity level to reach a pre-intervention symptom load. Thus, if FC is not accurately assessed, beneficial treatment outcomes may be missed. To address this issue, using extensive, repeated patient feedback we have developed a new questionnaire, FUNCAP, to achieve optimal FC assessment in ME/CFS patients. The questionnaire covers eight domains and activity types: A. Personal hygiene / basic functions, B. Walking / movement, C. Being upright, D. Activities in the home, E. Communication, F. Activities outside the home, G. Reactions to light and sound, and H. Concentration. Through five rounds of anonymous web-based surveys and a further test - retest validation round, two versions of the questionnaire were developed; a longer version comprising 55 questions (FUNCAP55) to improve diagnostic and disability benefit/ insurance FC assessments and a shorter version (FUNCAP27) for interventional research and less extensive FC assessments. FUNCAP may also be useful in other conditions where fatigue and PEM is present, such as Long Covid.

This study aimed to evaluate the capacity of Saccharomyces cerevisiae for Cadmium absorption in Milk. Nowadays one of the most serious problems is heavy metals pollution. Applying microorgaisms as a novel biotechnology is so useful especially in foodstuffs. Among the biosorbents for heavy metals’ removal, Saccharomyces cerevisiae has got an increasing attention due to its popularity in food industry. In this regard, the effects of some important factors such as the initial metal concentration, biomass concentration and contact time on the biosorption capacity of Saccharomyces cerevisiae were studied. The biosorption was analyzed by the inductively coupled plasma mass spectrometer (ICP-MS). The maximum Cd bioremoval (70%) was at 80 μg/L of this metal concentration in milk samples containing 30×10⁸ CFU Saccharomyces cerevisiae at the end of storage time (the 4^th day). There were no significant differences in sensory and physicochemical properties of milk samples during storage (p < 0.05). The isotherm studies followed by two popular models; Langmuir and Freundlich and the results showed a better fit to the Langmuir isotherm. All together, the results of this project demonstrated that the approach of using this valuable yeast, could be applied for food and drinks’ detoxification and producing healthier foods.

The most common index for representing structural condition of the pavement is the structural number. The current procedure for determining structural numbers involves utilizing falling weight deflectometer and ground-penetrating radar tests, recording pavement surface deflections, and analyzing recorded deflections by back-calculation manners. This procedure has two drawbacks: 1. falling weight deflectometer and ground-penetrating radar are expensive tests, 2. back-calculation ways has some inherent shortcomings compared to exact methods as they adopt a trial and error approach. In this study, three machine learning methods entitled Gaussian process regression, m5p model tree, and random forest used for the prediction of structural numbers in flexible pavements. Dataset of this paper is related to 759 flexible pavement sections at Semnan and Khuzestan provinces in Iran and includes “structural number” as output and “surface deflections and surface temperature” as inputs. The accuracy of results was examined based on three criteria of R, MAE, and RMSE. Among the methods employed in this paper, random forest is the most accurate as it yields the best values for above criteria (R=0.841, MAE=0.592, and RMSE=0.760). The proposed method does not require to use ground penetrating radar test, which in turn reduce costs and work difficulty. Using machine learning methods instead of back-calculation improves the calculation process quality and accuracy.

Worldwide the steel corrosion is one of the greatest deterioration problems for reinforced concrete structures. Comparing some literature experimental results with a complex FEM model, the present paper points out the principal aspects those characterize the static behavior of RC elements damaged by corrosion. Moreover, the non-dimensional abaci defined for some specific case studies finalized to the evaluation of the residual flexural strength of corroded elements highlight the dangerousness of the corrosion degradation if the failure of the element is governed by the steel

Highly weathered soils in the tropics are low in fertility, negatively affecting plant growth. The potential of biochar for improving soil nutrient retention is reportedly promising, triggering this study to assess the nutrient retention capacities of two biochars when applied at 2% in combination with two composts also applied at 2% to an Ultisol (Ustic Kanhaplohumult, Leilehua series) and an Oxisol (Rhodic haplustox, Wahiawa series) of Hawai’i. Chinese cabbage (Brassica rapa cv. Bonsai) was used as the test plant in two greenhouse plantings, which had a factorial completely randomized design with three replicates per treatment. The results indicated that the combined additions of biochar and compost significantly increased the pH, EC, P and K of the soils; improved Ca, Mg and Fe uptake; and increased shoot and total cabbage fresh and dry matter. Exchangeable aluminum in the Ultisol was decreased from 2.5 cmol+/kg to virtually zero. Extractable Mn and Fe in the high Mn-Oxisol were decreased by 55 and 42%, respectively. Chinese cabbage growth in the Ultisol amended with the lac tree (Schleichera oleosa) wood biochar and vermicompost was almost twice over lime at 2 cmol+/kg. Essential nutrients in the plant tissues, with the exception of N and K, were sufficient for the cabbage growth, suggesting increases in nutrients and reduced soil acidity by the additions of biochar combined with compost were the probable cause.

Heterogeneous systems of limited capacity have general applications in manufacturing, but also for logistic or service systems, due to the differences in server or workstation performance or work assignment, in close relationship with system flexibility, where saturation and blocking are ordinary situations of systems with high demand and limited capacity, so accurate loss quantification is essential for performance evaluation. Multi-class systems of limited capacity have been studied much less than parallel homogeneous systems (Erlang models). In this context, accurate models for parallel heterogeneous ordered-entry systems are developed: without any prior queue, M/Mi/c/c, and with a k capacity queue M/Mi/c/c+k. These new matrix models give an exact state formulation, and their accuracy is verified through discrete event simulation and comparison with literature results. Also, the effect of queue capacity is studied in relationship with the pattern of service rates. Next, the heterogeneous recirculating system model is also developed with good approximation results. Finally, the proposed models are applied to evaluate systems with non-exponential service times, through a new hybrid methodology by combining the Markovian model and the Monte Carlo Method (MCM) for normal or lognormal service times that also yield useful good approximations to the simulated system.

Lithium-ion batteries are key elements in the development of electrical energy storage solutions. However, due to cycling, environmental and operating conditions, battery capacity tends to degrade over time. Capacity fade is a common indicator of battery state of health (SOH) because it is an indication of how capacity has been degraded. However, battery capacity cannot be measured directly, so there is an urgent need to develop methods for estimating battery capacity in real time. By analyzing the historical data of a battery in detail, it is possible to predict the future state of the battery and forecast its remaining useful life. This paper develops a real-time, simple and fast method to estimate the cycle capacity of a battery during the charge cycle using only data from a short period of each charge cycle. This proposal is attractive because it does not require data from the entire charge period, since batteries are rarely charged from zero to full. The proposed method allows simultaneous and accurate real-time prediction of the health and remaining useful life of the battery over its lifetime. The accuracy of the proposed method has been tested using experimental data from several lithium-ion batteries with different cathode chemistries under various test conditions.

The process of rainfall interception by tree organs is crucial in mitigating the impact of intense rainfall on urban drainage systems, particularly in the context of climate change. this study selected ten commonly found tree species in Shanghai. Main parts of trees, including leaves, branches, and bark, were collected to analyze their ability to intercept rainwater. The optimized Artificial Rainfall Simulation System (ARSS) was applied to simulate the rainfall. The time-changing process of rainwater interception in three organs was measured during a 180-minute rainfall event which under four different rainfall intensities (4, 8, 12, and 16 mm/h, respectively). Process models of rainwater interception in different organs were fitted with adsorption kinetic equations. The rainwater interception process of tree organs complied with the quasi 2nd-order adsorption kinetic equation. The rainwater interception capacity of leaves, branches, and bark of ten urban tree species ranged from 0.05 to 0.34 mm, 0.13 to 0.24 mm, and 0.29 to 1.22 mm, respectively. The rainwater interception capacity of three organs significantly differs (p&lt;0.05). It reveals that bark exhibits the highest rainwater interception ability. Coniferous tree species have a greater ability to intercept rainwater than broad-leaved tree species. There are also differences in the rainwater interception ability of trees in urban and natural areas.

There is an increasing interest in revisiting plants for drug discovery proving scientifically their role as remedies. Pistacia lentiscus (PL) is a wild-growing shrub rich in terpenoids, which are pharmacological appealing. The more recurrent components in the oil are represented by α-pinene, terpinene, caryophyllene, limonene, and myrcene. High concentration of polyphenols enriches the extracts. PL-extracts showed in vitro and in animal model strong anti-inflammatory and anti-oxidative activities. The anti-inflammatory activity mainly occurs due to inhibition of NF-kB pathway or directly toward the proinflammatory cytokines, or arachidonic acid cascade against COX-2 and LOX. The antimicrobial activity of PL essential oil and extracts includes among others Staphylococcus aureus, Escherichia coli, periodontal bacteria and Candida sp.. In conclusion, the biological properties, and particularly the anti-inflammatory and anti-microbial capacity, propose PL as a new safe pharmaceutical agent.

In this paper, low circumferential reciprocating load foot-scale tests were performed on two truncated PHC B 600 130 tubular piles with bearing nodes to characterize the damage process and morphology of the specimens and to investigate the load-carrying performance of the members. The test results reveal that under the action of tensile-bending-shear loading, the bearing concrete in the node area buckles and is damaged, the anchored reinforcement in the node area yields, the constraint is weakened, an articulation point is formed, and the node rotational capacity increases. When the embedment depth increases from 200 mm to 300 mm, the ultimate bearing capacities of the positive and negative nodes increase by 57.60% and 54.60%, respectively. A numerical simulation is used to verify the test results. Considering the three types of piles with truncated nodes, the numerical simulation is used to analyze the node-bearing capacity at different embedment depths. Finally, two preferred node types are proposed as follows: pipe pile core-filled longitudinal reinforcement anchored into the bearing node and pipe pile body longitudinal reinforcement anchored into the bearing node + pipe pile core-filled longitudinal reinforcement anchored into the bearing node, with preferred embedment depths of 350 mm and 200 mm, respectively.

In the evolving landscape of vibration analysis, the integration of machine learning technologies for semi-automated analytical processes presents challenges in establishing clear cause-and-effect relationships in decision-making formulas. This research addresses this gap by exploring analytical diagnosis through residual signals, enabling the identification of anomalies and underperformance in machinery. Vibration signature analysis, focusing on distinctive vibration patterns, proves instrumental in detecting bearing defects and optimizing maintenance for enhanced operational efficiency and safety. Mathematical modeling, particularly worst-case analysis, provides a structured framework for decision-making under uncertainty. The research employs descriptive methods to analyze bearing wear data, transforming it into quantitative data for multiple regression equations. The derived equations reveal the dominance of harmonics in determining bearing wear stages, with PeakVue and overall vibration further indicating damage progression. The findings emphasize the significance of harmonic detection and high-frequency vibration analysis in predicting bearing health, offering a comprehensive approach to enhance machinery reliability. The study concludes with practical recommendations for bearing damage diagnosis based on the developed mathematical models, providing valuable insights for predictive maintenance strategies.

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

This research presents a novel Customised Load Adaptive Framework (CLAF) for fault classifica-tion in Induction Motors (IMs), utilizing the Machinery Fault Prevention Technology (MFPT) Bearing Dataset. CLAF represents a pioneering approach that extends traditional fault classification methodologies by accounting for load variations and dataset customization. Through a meticulous two-phase process, it unveils load-dependent fault subclasses that have not been readily identified in traditional approaches. Additionally, new classes are created to accommodate the dataset's unique characteristics. Phase 1 involves the exploration of load-dependent patterns in time and frequency domain features using one-way Analysis of Variance (ANOVA) ranking and validation via bagged tree classifiers. In Phase 2, CLAF is applied to identify mild, moderate, and severe load-dependent fault subclasses through optimal Continuous Wavelet Transform (CWT) selection through Wavelet Singular Entropy (WSE) and CWT energy analysis. The results are compelling, with a 96.3% classification accuracy achieved when employing a wide neural network to classify proposed load-dependent fault subclasses. This underscores the practical value of CLAF in en-hancing fault diagnosis in IMs and its future potential in advancing IM condition monitoring.

Japanese plums form part of a multi-billion rand deciduous fruit industry in South Africa. Despite this, there is a paucity of knowledge on the seasonal water requirements of plum orchards. In a time of changing climatic conditions and diminishing water resources, this gap in literature poses an imminent threat to the long-term sustainability and global competitiveness of the South African plum industry. Therefore, this paper aimed to provide a review of the available literature on the crop water requirements of full-bearing well-irrigated Japanese plum orchards for improved agricultural water management. Full-year water requirements for well-watered full-bearing Japanese orchards ranged between 921 and 1 211 mm a-1 with a mean value of 1 084 ±140 mm a-1. Canopy growth and pruning appeared to be the most common causes of differences in water requirement estimates. Growing season length also plays a role with late-season maturing orchards having higher water requirements than their early and mid-maturing counterparts. The knowledge review provided benchmark figures for the annual water requirements of Japanese plums. However further research is required to determine the water requirement of plums from planting to full-bearing age and the response of plum trees to water stress, in a South African context.

In Ecuador, particularly in the El Oro province, gold mining has been historically hampered by arsenic contamination in the ores. This research addresses the persistent issue of arsenic in gold-bearing ores from Miraflores Mine in Cerro Azul, Atahualpa Canton, and the challenges it presents to mining operations. The study's purpose is to evaluate the effectiveness of an alkaline leaching process for arsenic removal. The ore underwent thorough characterisation, employing advanced techniques like fire assay and atomic absorption. Once the ore's nature was discerned, an arsenic extraction experiment using a leaching solution was conducted. The implemented process achieved an arsenic removal efficiency of 90.54%. This enhanced ore quality facilitates efficient metallurgical applications and, more notably, reduces the environmental footprint by diminishing the need for harmful reagents like sodium cyanide. However, a significant implication of this method is the added cost due to the need for heat during the leaching test, amounting to an approximate $30 per ton increase. The alkaline leaching process emerges as a promising solution for arsenic challenges in El Oro’s mining sector. While the findings are encouraging, further expansive tests are recommended to validate the results and underscore the urgency for sustainable and hazard-conscious mining practices.

Condition monitoring is today a crucial and unavoidable practice related to the use of widespread mechanical components as rolling element bearings. Despite the diffusion of new data-driven techniques to analyze vibrational signals and detect the state of health of the system, mathematical tools, deriving more or less directly from the Fourier transform and defined either on the time or the frequency domain or on a combination of them (i.e. signal-based techniques), remain still essential and irreplaceable in the light of the deep and detailed information they provide. In this paper the diagnostic efficacy of an ample spectrum of these methods is investigated, applying them to study faults occurrence in the first bearing dataset released by NASA IMS Center. Thanks to their analytical definition, which is formulated taking into consideration to some extent the mathematical nature of the signal, faults signatures can be clearly identified and their temporal development can be fully traced, confirming their ability as powerful means to constantly monitor the state of a system even in real-time applications.

In the subcratonic mantle beneath Leningrad pipe, West Ukukit field, Yakutia garnet thermoba-rometry give division to 7 horizons (paleosubduction slabs). Cr-bearing amphiboles >500 reveal a broad range changing from Cr- pargasitic hornblendes to pargasites, edinites, kataforites, К-richterites with increasing pressure determined with new amphibole thermobarometer. Cr-hornblendes compiles the high-temperature branch from 3.5 GPa to Moho for basaltic melt. Amphiboles in the middle eddinites and high-pressure interval reveal different PT ranges from 35 to 40 mw/m2. Richterites near the lithosphere base both trace low –T and convective branches. The amphiboles reveal the 9 geochemical groups. The low-temperature varieties reveal Eu minima and U, Ba, Sr peaks high LILE, Sr, Rb and troughs in Nb, Pb. While high –T varieties have no Eu dips and reveal higher HFSE. Clinopyroxenes and garnets show variable trace ele-ment patterns and divisions in groups eth the plume and subduction signs. The contrasting be-haviour of Ta and Nb is regulated by the rutile partition coefficients likely for primary eclogites. Subduction and Na and K (siliceous) types of fluids percolated through the mantle with abun-dant eclogites causing amphibolization at the different levels of the mantle column. The plume melts produced hybridism and more smooth trace element patterns in reacted minerals, clino-pyroxene. monomineral thermobarometry.

We report the development of in vitro propagation protocols through adventitious shoot induction pathway for a rare and medicinal Scutellaria havanensis. In vitro propagation studies using nodal explants showed MS medium supplemented with 10µM 6-Benzylaminopurine induced highest number of adventitious shoots in a time dependent manner. A ten - day incubation was optimum for shoot bud induction as longer exposures resulted in hyperhydricity of the explants and shoots induced. We also report preliminary evidence of Agrobacterium tumefaciens EHA105 - mediated gene transfer transiently expressing of green fluorescent protein in this species. Transformation studies exhibited amenability of various explant tissues, internode being the most receptive. As the plant has medicinal value, research was carried out to evaluate its potential antioxidant capacity and the efficacy of methanolic leaf extracts in curbing the viability of human colorectal cancer cell line HCT116. Comparative total polyphenol, and flavonoid content measurement of fresh and air dried leaf extract revealed that the fresh leaf extracts contain higher total polyphenol and flavonoid content. The HCT 116 cell viability assessed by colorimetric assay using a 3-(4, 5-dimethyl-thiazol-2-yl)-2, 5-diphenyltetrazolium bromide, showed a steady growth inhibition after 24 hours of incubation. Scanning Electron Microscopy of leaf surface revealed high density of glandular and non-glandular trichomes. This research provides basis for the conservation of this rare plant and future phytochemical screening and clinical research.

Roundabouts need capacity and safety improvements compatible with manual-driven, not only with autonomous vehicles. The signaling and control of roundabouts must evolve and incorporate current technologies. For that, we approach roundabouts as synchronous switches of vehicles. This paper describes Synchronous Roundabouts with Rotating Priorities, a roundabout control system based on vehicle platoons arriving at the roundabout at speed identical to the roundabout and within the time slot assigned to their entry, avoiding conflicts and stops, thus increasing roundabout capacity and safety. Signaling is visual for human drivers and also wireless for connected and autonomous vehicles. We evaluate analytically and with simulations roundabouts of different radius for several values of the average distance between vehicles. Average delays are 28,7 % lower, with negligible dispersion. The capacity improvements depend on design parameters: in our set is moderate for small roundabouts but goes up to 70-100 % for short distances and medium and large roundabouts.