For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

An upsurge in global population over the years and rapid urbanization have accelerated huge dependence on petroleum-derived fuels and consequent environment concerns owing to green-house gas emissions in the atmosphere. An integrated biorefinery uses lignocellulosic feedstock as raw material for the production of renewable biofuels, and other fine chemicals. The sustain-able bio-economy and the biorefinery industry would benefit greatly from the effective use of lignocellulosic biomass obtained from agricultural feedstocks to replace petrochemical products. Lignin, cellulose, hemicellulose, and other extractives, which are essential components of ligno-cellulosic biomass, must be separated or upgraded into useful forms in order to fully realize the potential of biorefinery. The development of low-cost and green pretreatment technologies with effective biomass deconstruction potential is imperative for an efficient bioprocess. The abun-dance of microorganisms along with their continuous production of various degradative en-zymes makes them suited for the environmentally friendly bioconversion of agro-industrial wastes into viable bioproducts. The present review highlights the concept of biorefinery, ligno-cellulosic biomass and its valorization by green pretreatment strategies into biofuels and other biochemicals. The major barriers and challenges in bioconversion technologies, environmental sustainability of the bioproducts and promising solutions to alleviate those bottlenecks are also summarized.

The maintenance of traditional agricultural practices in protected small islands is closely linked to the preservation of the land, the protection of natural resources, and the conservation of local traditions. For this purpose, the Tuscan Archipelago National Park promoted the census of ancient horticultural varieties preserved by some farmers on the island of Elba. The survey revealed a deep-rooted historical, cultural, social, and economic link between this germplasm and the island’s territory. A scientific characterization of the landrace under ethnobotanical, morphological, and genetic aspects was carried out. Among these local varieties, two landraces of the Brassica species and three landraces of the Phaseolus species were identified and analyzed in this study. To ascertain their distinguishability and uniqueness, similar varieties were also identified based on morpho-physiological characteristics or territorial proximity and compared with the Elban landraces. Morpho-phenological data were collected, and molecular analyses were carried out using Simple Sequence Repeats (SSR) markers. Ten different SSR loci were considered for the Phaseolus species and nine for the Brassica species. The Tuscan Archipelago landraces showed a high level of internal variability but were clearly distinct from each other and from the analyzed varieties, as shown by AMOVA (Analysis of Molecular Variance). Their distinctness was further highlighted by the UPGMA dendrogram obtained from the genetic distance matrix. The same results were confirmed by Principal Coordinate Analysis (PCoA). This study confirms the peculiarity of the Elban landraces, their biodiversity is a heritage to be safeguarded, which can also be used in future breeding programs. These ancient Elban landraces were allocated to local farmers (most were young farmers) to protect them from extinction and to promote more resilient varieties cultivation compared to commercial hybrids widely spread in the area. Local farmhouses also play a strategic role in safeguarding the germplasm and dissemination of sustainable agricultural practices. There is high demand for ancient Elban landraces, this has led to the development of a new local economy balanced between agricultural tradition and innovation.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Abstract: Field studies with large-stemmed plants Artemisia dubia (wormwood) have been carried out at Vėžaičiai Branch LAMMC since 2018. According to three years of experimental results, annual dry matter (DM) yield varied from 7.94 to 10.14 t ha-1. Growing conditions, nitrogen ap-plication level and harvesting time had significant impacts on Artemisia dubia productivity. This article presents the results of research on preparation and use of Artemisia dubia biomass for en-ergy conversion and evaluation of technological-technical and environmental parameters of these plants utilization for solid biofuel. For experiments were used 6 variants of Artemisia dubia samples, which were grown in 2021: plants were cut three times and two fertilization options were used: (1) no fertilization and (2) fertilization with 180 kg ha-1 of nitrogen fertilizer. These harvested plants were chopped, milled and were pressed into the pellets. The physi-cal-mechanical characteristics (mоisture content, density and strength) of Artemisia dubia pellets were investigated. During this study, it was found that the density in dry mass (DM) of pellets ranged from 1119.86 to 1192.44 kg m-3. The pellet moisture content ranged from 8.80 to 10.49%. After testing of pellet strength, it was found that the pellets which were made from plant bio-mass PK-1-1, were the most resistant to compression, they withstood 560.36 N of pressure. Dry fuel lower heating value (LHV) of pellets was sufficiently high and was very close to pine saw-dust pellets, it varied from 17.46±0.25 MJ kg-1 to 18.14±0.28 MJ kg-1. The ash content of burned pellets ranged from 3.62±0.02% to 6.47±0.09%. Emissions of harmful pollutants – CO2, CO, NOx and unburnt hydrocarbons (CxHy) did not exceed the maximum permissible levels. Summariz-ing the results of investigated properties, cоmbustion and emissiоns of Artemisia dubia pellets, it can be concluded that this biofuel can be used for production of pressed biofuel and it is charac-terized by sufficient high quality, efficient combustion and permissible emissions to the envi-ronment.

Accurately estimating shrub biomass in arid and semi-arid regions is critical for understanding ecosystem productivity and carbon stocks at both local and global scales. However, capturing the shrub biomass accurately by satellite observations is challenging due to the short and sparse features of shrubs. In this study, we presented a framework to estimate shrub biomass at a 10m spatial resolution by integrating ground in-situ data, unmanned aerial vehicle (UAV), Sentinel-2, and Sentinel-1 observations. The pilot study was conducted in the Helan mountains of Ningxia province, China. First, the spatial distribution map of shrubland and other land cover types was generated in 2023. Then, a prediction model of shrub biomass was developed in a Random Forest Regression (RFR) approach driven by different predicted variable datasets based on in-situ measurements, UAV, and satellite images. Finally, the developed model was used to produce the biomass map of shrubland in 2023. The uncertainty was characterized by creating a standard deviation (SD) map using the Leave-One-Out Cross-Validation (LOOCV) method in the shrub biomass estimates. The resultant shrubland distribution map in 2023 has an F1 score of 0.92. The shrub biomass model driven by spectral bands and vegetation indices (R2= 0.62) demonstrated superior performance than that only driven by spectral bands (R2=0.33) or vegetation indices (R2=0.55). The uncertainty of the estimated biomass was lower than 4%, with the lowest values (<2%) happening in the high shrub coverage (>30%) and biomass production (>30kg/m2) regions. Furthermore, the findings show that the magnitude of shrub biomass was affected by the aridity and precipitation significantly in the study region. This study provides a workflow to accurately monitor the biomass of shrublands in a complicated environment based on remote sensing images from multi-platform observations.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

The expanding global population has increased the demand for sustainable protein sources, and microbial protein (MP) has emerged as a promising alternative. However, conventional carbon (glucose) and nitrogen (ammonia, urea) sources needed for MP production pose environmental and economic issues. This study aims to produce protein using lignocellulosic biomass (LCB) as a carbon source and the nitrogen fixation ability of Klebsiella oxytoca M5A1 as a nitrogen source. The study investigates the pretreatment of LCB (switchgrass), enzymatic hydrolysis, protein quantification, and high-performance liquid chromatography system (HPLC) analysis to track glucose utilization and organic acid production. K. oxytoca M5A1 harnessed free nitrogen from the atmosphere through nitrogen fixation and used abundant, cheap glucose from LCB to produce MP and organic acids as by-products. Protein production occurred in two phases: first within the initial 8 hours and secondly, within the last 16 hours. The highest protein concentration was at 40 hours, with approximately 68.3% protein content. HPLC analysis revealed a dynamic profile of glucose utilization and organic acids (Lactic acid, Propionic acid, Acetic acid, and Succinic acid). K. oxytoca M5A1 exhibited an early high rate of glucose consumption, and conversion to organic acids that were later used for second-phase protein production. The acids profile revealed intra-conversion from one acid to another via metabolic pathways (glycolysis and tricarboxylic acid cycle). Overall, leveraging LCB and the nitrogen-fixing ability of K. oxytoca M5A1 for MP production offers an eco-friendly and cost-effective alternative to traditional protein sources, contributing to a sustainable circular economy.

Reducing the carbon footprint of energy production is one of the most pressing challenges facing humanity today. Lignocellulosic biomass residues from fruit production industries show promise as a viable energy source. This paper presents a study of the Italian context concerning the utilization of orchard lignocellulosic residues for energy production as electricity or bioethanol. The potential of various orchard residues was assessed through chemical and physical analysis, and an equivalent electrical energy of about 6441.62 GWh or an amount of 0.48 Mt/y of bioethanol was obtained based on the average annual dry residue mass availability of about 3.04 Mt/y. These data represent the 9.30% of the national electrical energy production from renewable sources, as well as the 6.21% of the Italian demand for gasoline in 2022. Electricity generation from these residues shown its potential as a reliable and sustainable baseload power source, as well as source of renewable transportation fuel. The studied process could be a valuable reference to expand these concepts on global scale to achieve a greener and more sustainable energy future.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

Industries are required to utilize treatment technologies to reduce contaminants in wastewater prior discharge and valorize by-products to increase sustainability and competitiveness. Most acid leaching gypsum purification studies have obviated the treatment of the highly acidic wastewater produced. In this work, acidic wastewater from acid leaching purification of post-consumer gypsum was treated to recover a valuable solid product and reusable water. The main aims of this work were to determine the impact of recirculating acidic and treated wastewaters on the efficiency of the acid leaching purification process and to valorize the impurities in the wastewater. Samples were characterized through X-ray fluorescence and X-ray diffraction. SimaPro 9.5 and ReCiPe 2016 midpoint method were used for the life cycle assessment of three wastewater management approaches. The reuse of the acidic wastewater did not improve the chemical purity of gypsum. Soluble impurities were precipitated at pH 10.5 as a magnesium-rich gypsum that could be commercialized as fertilizer or soil ameliorant. The alkaline treated water was reused for 6 acid leaching purification cycles without impacting the efficiency of the purification process. An acid leaching-neutralization-filtration-precipitation approach demonstrated superior overall environmental performance. Barriers and enabling measures for the implementation of an in-house wastewater treatment were identified.

To realize the utilization of peanut shell, this study investigates the combustion behavior, chemical kinetics, and thermodynamic parameters of peanut shell using TGA under atmospheric air. Results indicate that increasing the heating rate leads to higher ignition, burnout, and peak temperatures, as observed in the TG/DTG curves shifting to the right. Analysis of combustion performance parameters suggest that higher heating rates can enhance combustion performances. Kinetic analysis using two model-free methods, KAS and FWO, shows that the activation energy (Eα) ranges from 93.30 to 109.65 kJ/mol for FWO and 89.72 to 103.88 kJ/mol for KAS. The data fit well with coefficient of determination values (R2) close to 1. Pre-exponential factors using FWO range from 2.19×106 to 8.06×107 s–1, and for KAS range from9.72×105 to 2.25×107 s–1. Thermodynamic analysis indicates a low-energy barrier (≤ ±6 kJ/mol) between activation energy and enthalpy changes, suggesting easy reaction initiation. Furthermore, variations in enthalpy (ΔH), Gibbs free energy (ΔG), and entropy (ΔS) upon conversion (α) suggest that peanut shell combustion is endothermic and non-spontaneous, with the generation of more homogeneous or well-ordered products as combustion progresses. These findings offer a theoretical basis and data support for the further utilization of agricultural biomass.

Hemicellulose is one of the most important natural polysaccharides in nature. Hemicellulose from different sources varies in chemical composition and structure, which in turn affects the modification effects and industrial applications. Grain and oil by-products (GOBP) are important raw materials for hemicellulose. This article reviews the modification methods of hemicellulose in GOBP. The effects of chemical and physical modification methods on the properties of hemicellulose biomaterials were evaluated. The potential applications of GOBP hemicellulose in films, hydrogel, Three-dimensional (3D) printing and adsorbent are discussed. Future research directions and recommendations are also proposed to provide theoretical foundations and technical support for the efficient utilization of these by-products.

This study investigates the valorization potential of yellowfin tuna tails for the production of high-value commercial products. Muscle and skins were firstly mechanically separated by using a specifically designed device. The muscle was then used as a nitrogen source for the growth of the proteolytic enzymes-producer Bacillus subtilis, whereas the skins were employed for gelatin extrac-tion. The proteases from Bacillus subtilis were partially purified and used to produce antioxidant peptides from gelatin obtained. The gelatin obtained formed a gel upon cooling, with gelling and melting temperatures at 16 ºC and 22 ºC, respectively, and Bloom Strength of ≈ 160. RSM was used to determine the optimal hydrolysis conditions to obtain the highest antioxidant activity (35.96%, measured as DPPH radical scavenging activity), which were 50°C / 6.5 IU of enzyme. The findings emphasize the importance of an integrated approach to maximize the value of tuna by-products, promoting sustainability in the frame of circular bioeconomy. Overall, these results contribute to the efficient utilization of tuna by-products, waste reduction, and enhance economic viability of the tuna industry.

In municipal waterworks large amounts of waste in the form of sludge have to be discarded. This investigation focuses on the processing of ceramic floor tiles incorporated with a municipal waterworks sludge. Four floor tile formulations containing up to 10 wt. % of the municipal waterworks sludge in replacement of kaolin were prepared. The floor tile processing route consisted of dry powder granulation, uniaxial pressing, and firing between 1190 and 1250 °C using a fast-firing cycle (<60 min). The densification behavior and technological properties of the floor tile pieces as function of the sludge addition and firing temperature were determined. The development of the microstructure was followed by XRD and SEM/EDS. The results show that the replacement of kaolin with municipal waterworks sludge, in the range up to 10 wt. %, allows the production of ceramic floor tiles (group BIb and group BIIa, ISO 13006 Standard) at lower firing temperatures. These results suggest a new possibility for valorization of municipal waterworks sludge with many economical and environmental benefits.

The article presents a model for optimizing biomass supply chains using the linear programming framework integrated with a Geographic Information System. Based on the distance from a given type of biomass resource, its calorific value, price, and transportation costs, the model identifies the optimal source of biomass, allowing it to cover the demand for the required total energy value with the lowest possible costs. The case study includes the Połaniec power plant in southeastern Poland and potential sources of forest biomass and agricultural straw within 100 km of the plant. Unit costs of biomass varied depending on biomass availability and energy demands. For energy demand on the level of 1 PJ yearly, the lowest unit costs of biomass (4.08 €/MJ) were when all kinds of biomass were available, and the highest (5.47 €/MJ) was when only stacked wood was available. As energy demand increased, unit costs increased, and the ability to meet this demand with just one type of biomass decreased. The energy biomass sector can utilize the model to benefit both biomass producers and their final buyers.

Lignocellulosic biomass has garnered attention as an abundant and sustainable alternative energy source that can facilitate reliable and environmentally friendly energy generation. Energy security improves, and environmental impacts diminish when bioethanol, a biofuel produced via lignocellulose-based processes, is utilized. The lignocellulosic biomass of Thysanolaena latifolia has considerable potential as a bioethanol feedstock due to its high carbohydrate content (62.4 ± 0.7%). In this study, feedstock derived from T. latifolia was pretreated with various concentrations of H3PO4 to determine the ideal conditions for enzymatic hydrolysis to convert the feedstock to fermentable sugar. The findings revealed that hydrolysis efficiency and glucose recovery yields were substantially improved compared to those of the untreated sample. Pretreated samples were enzymatically digested to produce a liquid hydrolysate. This hydrolysate was fermented without detoxification using Saccharomyces cerevisiae TISTR 5339 to produce ethanol. The results indicated that T. latifolia biomass hydrolysate is a promising long-term carbon source for ethanol production from cellulosic biomass. Furthermore, the morphological and crystallographic characteristics of the treated T. latifolia biomass were influenced by H3PO4 concentration, as indicated by the SEM images, X-ray diffractogram patterns, and crystallinity index values. Therefore, utilizing T. latifolia feedstock to produce bioethanol can enhance bioenergy sustainability.

The search for new food products that promote consumers health has always been of great interest. The dairy industry is perhaps the best example regarding the emergence of new products with claimed health benefits. Cheese whey (CW), the by-product resulting from cheese production, and second cheese whey (SCW), which is the by-product of whey cheese manufacture, have proven to be potential ingredients for the development of food products with improved nutritional characteristics and other functionalities. Nowadays, due to their nutritional quality, whey products have gained a prominent position among healthy food products. However, for long, CW and SCW were usually treated as waste or as animal feed. Due to their high organic content, these by-products can cause serious environmental problems if discarded without appropriate treatment. Small and medium size dairy companies do not have equipment and structure to process whey and second cheese whey. In these cases, generally, they are used for animal feed or discarded without an appropriate treatment, being the cause of several constraints. There are several studies regarding CW valorization and there is a wide range of whey products in the market. However, in the case of SCW remains a lack of studies regarding its nutritional and functional properties, as well as ways to reuse this by-product in order to create economic value and reduce environmental impacts associated to its disposal.

Waste orange peel represents a heavy burden for the orange juice industry, estimated in several million tons per year worldwide; nevertheless, this by-product is endowed with valuable bioactive compounds, such as pectin, polyphenols and terpenes. The potential value of the waste orange peel has stimulated the search for extraction processes, alternative or complementary to landfilling or to the integral energy conversion. This study introduces controlled hydrodynamic cavitation processes, as a new route to the integral valorization of this by-product, based on simple equipment, speed, effectiveness and efficiency, scalability, and compliance with green extraction principles. Waste orange peel, in batches of several kg, was processed in more than 100 L of water, absent any other raw materials, in a device comprising a Venturi-shaped cavitation reactor. The extractions of pectin, endowed with a very low degree of esterification, polyphenols (flavanones and hydroxycinnamic acid derivatives), and terpenes (mainly d-limonene) were effective and fast (high yield, few min of process time), as well as the biomethane generation potential of the process residues was effectively exploited. The achieved results proved the viability of the proposed route to the integral valorization of waste orange peel, though wide margins exist for further improvements.

The focus of our study was the changes in the composition of semi-natural dry grasslands in Hungary. Since these valuable habitats were created with the help of humans, their preservation also requires regular treatment. Our mowing experiment aimed to investigate the suppression of the native Calamagrostis epigejos L. Roth. In Hungary, in the Cserhát Mountains, eight permanent plots were mowed twice a year. The vegetation was sampled annually between 2001 and 2011. The effects of mowing were investigated with repeated measures analysis of variance (ANOVA). After 10 years, the C. epigejos cover of the mowed plots decreased significantly, from the initial average of 62.38 to 7.50%. Surprisingly, we also experienced a similar decrease in the control plots. Regular treatment also had a positive effect on the number of species and diversity. Species richness increased continuously in both treatment types, which indicates the combined effect of vegetation succession and treatment. The biomass growth of other Poaceae and Fabaceae species, which are important from a grassland management perspective, was also facilitated by mowing. Our results suggest that long-term in situ experiments and continuous botanical studies are needed to establish a reliable utilization of grasslands.

A non-destructive analysis of proximate parameters (moisture content, MC; volatile matter, VM; fixed carbon, FC; and ash content) for a variety of chipped and ground biomasses was investigated through a combination of thermogravimetric analysis (TGA) and near-infrared spectroscopy (NIRS) with partial least squares regression (PLSR). In this study, the thermogravimetric method was employed as a tool to determine the proximate analysis data of biomass samples through TG and DTG curves, which were generated by tracking changes in biomass mass loss over time or temperature. NIRS non−destructively scanned the chipped biomass in diffuse reflectance while ground biomass using transflectance mode, covering the wavenumber range of 3594.87 to 12,489.48 cm−1. The PLSR−based models: Full−PLSR, genetic algorithm (GA)−PLSR, successive projection algorithm (SPA)−PLSR, the spectral multi−preprocessing (MP) PLSR− 5 range method, and the MP PLSR−3 range method were developed. Model performance was assessed, compared, and selected based on the coefficient of determination in the prediction set (R2P), root mean square error in the validation set (RMSEP), and the ratio of prediction to deviation (RPD). Based on the comprehensive analysis of model performance, MC and FC models of chip biomass have demonstrated satisfactory performance which makes it applicable cautiously in any application, including research. The optimum models for MC and FC in chip biomass were constructed using GA−PLSR with 2nd derivative and Full−PLSR with a constant offset, resulting in R2P values of 0.8654 and 0.8773, RMSEP values of 0.85% and 2.12%, and RPD values of 2.9 and 3.0, respectively. Other parameters such as MC and FC in ground biomass as well as VM and ash content in both chip and ground biomass were found suitable for rough screening. The sensitivity of the selected model was assessed by calculating the limit of quantification (LOQ), and the results indicated that the calculated LOQ values for VM in both chip and ground biomass and FC in chip biomass are lower than the minimum reference values used during model development, signifying a high level of sensitivity. However, for the remaining parameters, the LOQ values surpass the established minimum reference value, suggesting the model could not predict the future samples with reference value lower than the calibration range. Nevertheless, enhancing the models by incorporation an ample number of representative biomass samples and consistently validating the models with unknown samples is imperative to ensure accurate predictions.

Abstract: The present work evaluates the feasibility of using volcanic fly ash (VFA), generated by the eruption of the Tajogaite volcano on the island of La Palma (Spain) in 2021, as a precursor in the preparation of cementitious materials with different Portland cement (PC) replacement levels (0%, 30%, 70% and 100%), in the absence (Blended Cement, BC) and presence of an alkaline ac-tivator (Hybrid Alkaline Cement, HAC, and Alkaline Cements, AC). Hydration kinetics (isother-mal conduction calorimetry), paste mechanical strengths and reaction products were character-ised by XRD, FTIR, TG/DTG and BSEM/EDX. The results obtained indicate that the strengths de-veloped by the hybrid alkaline cements (HAC) are higher than those of the blended cements (BC), especially at the age of 2 days, where 25 MPa was obtained with the replacement of 70% PC by VFA. Alkaline cements (AC, 100% VFA) prepared with 8M NaOH solution as activator reached 40 MPa after 2 days. It was observed that in all the binders, depending on the initial composition of the binder mixture and the percentage of replacement and/or activator, VFA reacts to form cementitious gels, C-A-S-H and N-A-S-H type, which supports its use as a mineral addition to blended cement or as a precursor in the preparation of alkaline and hybrid alkaline cements.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

This study was conducted to explore the potential of superabsorbent polymers (SAPs) from used disposable diapers as soil moisture conditioner. Swelling behavior of the proposed hydrogel in response to external stimuli such as salt solutions, temperature and pH was studied. In addition, laboratory experiments were carried out to evaluate the effects of incorporation hydrogel on germination of bean (Phaseolus vulgaris L.) and pumpkin (C. pepo) seeds. The structure of the superabsorbent was characterized by Fourier transform infrared spectroscopy (FTIR). The results indicate that the proposed SAP exhibited a maximum swelling capacity of 189 g.g-1 of dry gel. It was observed that the swelling capacity decreased with an increase in the ionic strength of the swelling medium. When this SAP was mixed with sandy soil, the mixture was able to lose water more slowly. The seeds germination and seedling growth was remarkably influenced by the application of 0.5, 1.0 and 2.0 w/w% of SAP compared to the untreated soil. Therefore, it follows that it is possible to take advantage of SAPs property from used disposable diapers to retain the moisture in soil as an alternative to value the use of such waste, showing that it has potential for diverse applications in agriculture.

Human and animal waste, including waste products originating from human or animal digestive systems such as urine, feces, and animal manure, have constituted a nuisance to the environment. Inappropriate disposal and poor sanitation of human and animal waste often cause negative impacts on human health through contamination of the terrestrial environment, soil, and water bodies. Therefore, it is necessary to convert these wastes into useful resources to mitigate their adverse environmental effect. The present study provides an overview and research progress of different thermochemical and biological conversion pathways for the transformation of human- and animal-derived waste into valuable resources. The physicochemical properties of human and animal waste are meticulously discussed as well as nutrient recovery strategies. In addition, a bibliometric analysis is provided to identify the trends in research and knowledge gaps. The results reveal that the U.S.A, China and England are the dominant countries in the research areas related to resource recovery from human or animal waste. In addition, researchers from the University of Illinois, the University of California Davis, the Chinese Academy of Science and Zhejiang University are front runners in research related to these areas. Future research should be centred on developing technologies for the on-site recovery of resources, exploring integrated resource recovery pathways, and exploring different safe waste processing methods.

The scope of this paper is to use plastic waste through the gasification process for producing electricity with low carbon dioxide emissions. Worldwide, plastic production increased, reaching 367 million tons in 2020, compared with 1.5 million tons in 1950. It is known that plastic incineration generates approximately 400 million tons of CO2 annually, and consequently, new solutions for a more efficient plastics reuse in terms of emissions generated are still expected. One method is to use plastic waste in a gasifier unit and the syngas generated in a gas turbine for electricity production. The co-gasification process (plastic waste with biomass) was analysed in different ratios. Gasification was carried out with air for an equivalent ratio (ER) between 0.10-0.45. The volume concentration of CO2 in syngas ranged from 2-12%, with the highest value obtained when poplar content in the mix was 95%. In this study, the option of pre- and post-combustion integration of the chemical absorption process (CAP) was investigated. Thus, CO2 emissions have decreased by 90% compared with the case without CO2 capture. By integrating the capture process, the global efficiency has reduced with 5.5 – 6.1 percentage points in a post-combustion case, according to the plastic content in the mix.

Nowadays, inherently safer designs are considered as key priorities to prevent or mitigate serious incidents with devastating consequences. The need for process safety assessment during early design phases has motivated the development of several contributions related to computer-aided assessment methodologies in order to measure the inherent safety of chemical processes. In this work, the large-scale production of chitosan from shrimp wastes was evaluated from process safety point of view using the numerical descriptive inherent safety technique (NuDIST).To this end, simulation of the chitosan production was performed using Aspen Plus ® to obtain extended mass and energy balances. The assessment of all the chemicals involved within the process was carried out for the following safety parameters: explosivity (EXP), flammability (FL) and toxicity (TOX). The safety assessment of the process included the parameters of temperature (T), pressure (P) and heat of reaction (HR). The maximum chemical safety score was estimated in 171.01 with ethanol as main contributor to the parameter of explosivity and flammability. The score associated with operating data was calculated in 209.30 and heat of reaction reported to be the most affecting parameter. The NuDIST score was estimated in 380.30. This NuDIST value revealed the low hazards associated with the handling of substances such as shrimp wastes, chitosan and water, as well as the non-extreme temperature and pressure conditions. In general, the large-scale production of chitosan from shrimp shells showed to be an inherently safe alternative of waste valorization.

The use of biomass as a source of energy has been identified to be energy intensive which involves high cost of handling. However, pelletization reduces the bulk density of biomass, thereby reducing the cost of handling and enhancing ease of use. This study modified and evaluated an existing hand operated fish feed pelleting machine. The parts of the machine that were redesigned are hopper and power transmission unit. Corncob was used to evaluate the modified machine using die hole diameter (5,6 and 7 mm) and binder quantity (0, 2.5 and 5 wt%) as factors. The average results obtained for machine efficiency, throughput, pellet length and bulk density were 58.83%, 4.24 kg/h, 15.51 mm and 0.160 g/cm3. Die hole diameter had significant effect on pellet length only. Binder quantity had significant effect on machine efficiency, throughput and pellet length. Machine efficiency and throughput reduces as the quantity of binder increases and pellet length increases with increasing quantity of binder.

The present study aimed at utilizing technically hydrolyzed lignin (THL), industrial biomass residue, derived in high-temperature diluted sulphuric acid hydrolysis of softwood and hardwood chips to sugars. The THL was carbonized in horizontal tube furnace at atmospheric pressure, in inert atmosphere and at three different temperatures (500, 600 and 700 ºC). Biochar chemical composition was investigated along with its HHV, thermal stability (thermogravimetric analysis) and textural properties. Surface area and pore volume were measured with nitrogen physisorption analysis often named upon Brunauer–Emmett–Teller (BET). Increasing the carbonization temperature reduced volatile organic compounds (40 ÷ 96 wt. %), increased fixed carbon (2.11 to 3.68 times the wt. % of fixed carbon in THL), ash and C-content. Moreover, H and O were reduced, while N- and S-content were below the detection limit. This suggested biochar application as solid biofuel. The biochar Fourier-transform infrared (FTIR) spectra revealed that the functional groups were gradually lost thus, forming materials having merely polycyclic aromatic structures and high condensation rate. The biochar obtained at 600 and 700 ºC proved having properties typical for microporous adsorbents, suitable for selective adsorption purposes. Based on the latest observations another biochar application was proposed - as catalyst.

Less than half of e-waste plastics is sorted worldwide and this rate is likely to decline as major processing countries have banned importation of e-waste plastics. This forces the development of decentralized processing facilities, also known as microfactories. The present work investigates the recyclability of different grades of acrylonitrile-butadiene-styrene (ABS) copolymer, polycarbonate, and polypropylene, which were found to be very abundant in a recycling site in the UK. The determination of the matrix relied on the resin identification code imprinted in the e-waste plastic and subsequent FTIR analysis. The melt-blend extrusion technology enabled the valorization of the wasted thermoplastics as 3D filament without significant degradation of the polymers. The recycled materials maintained the tensile strength around 2.5 MPa in agreement with the specifications offered by virgin polymers. Further characterization was done by means of laser microscope, thermogravimetric analysis, and XRF to determine the commercial viability of the recycled filament. A modified solvent-based method was developed with acetone to remove the brominated flame retardants: 25g/100mL, 30 minutes of contact time, and 4 extraction steps. The FTIR results show that the degradation of the rubbery dispersed phase corresponding to the butadiene can be accumulated in the less soluble fraction of the waste ABS.

The production of biomass fly ash has been increasing every year in Europe, reaching 5.5 million tons in 2020. Biomass fly ash is not yet accepted in the standards as a substitute material for cement in mortar and concrete. In a first approach, the substitution limit of biomass fly ash is determined by comparing the mechanical strengths, fresh state properties and hardened properties of mortars produced with biomass fly ash to those of mortars produced with classical coal fly ash. Then, masonry and rendering mortars have been designed with different substitution rates of biomass fly ashes from wood combustion in thermal power plant. Although there is an overall decrease in performance, mortars made with biomass ash retain properties that make them suitable for use in masonry or rendering.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

Dye-containing effluent generated in textile industries is polluting and complex wastewater. It should be managed adequately before the final destination. The up-flow anaerobic blanket (UASB) reactor application is an eco-friendly and cost-competitive treatment. The present study briefly reviews the UASB application for dye wastewater valorization. Bioenergy and clean water production potential during dye-containing wastewater treatment are emphasized to promote resource recovery in textile industries. Efficiencies of color and chemical oxygen demand of 50–97% and 60–90% are reported in bench-scale UASB studies. A biogas yield of 0.36–36.04 L d-1 in UASB, which treats dye-containing effluents, is documented. Bioenergy production and water reuse allow environmental and economic benefits. However, data on full-scale UASB treating dye wastewater are missing. Besides, studies on combined systems integrating membrane processes, such as ultrafiltration and nanofiltration, and pretreatment of wastewater and sludge for improvements in biogas production might realize the complete potential for resource recovery of UASB technology.

The valorization of aquaculture/fisheries processing by-products, as well as unavoidable/unwanted catches and discards in Greece is currently an underutilized activity despite the fact that there are several best practices in Northern Europe and overseas. One of the main challenges is to determine whether the available quantities for processing are sufficient to warrant valorization of discards and fish side streams. This is the first attempt to systematically record and analyze the available quantities of fish by-products and discards in Greece in a spatial and temporal way in an effort to create a national exploitation Master Plan for the valorization of this unavoidable and unwanted biomass. A thorough survey conducted within the VIOAXIOPIO project unveiled a substantial biomass of around 19,000 tonnes annually that could be harnessed for valorization. Furthermore, the production of various High Added Value Biomolecules (HAVB) was investigated, and experimental trials were conducted to assess the potential yields and the collected data were used to formulate four valorization scenarios.

Enzymes are biological molecules produced by living entities for carrying out biological processes. The application of enzymes for waste treatment has been gaining pace commercially to solve concerns related to agricultural residues, wastewater, replacement of synthetic processes with natural ones, etc. The application of enzymes for waste management has been an environmentally reliable and sustainable process. Treatment of waste with enzymes such as xylanase, proteases, hydrolases, cellulose, peroxidases, chitinases, laccases, etc. has been studied to be effective. These enzymes act upon the waste products and transform them into biodegradable forms that can be recycled, reused and converted to value-added products. They have wide applications and utility as it has been an effective approach, economically cheaper and sustainable techniques. Application of such enzymes for waste management would be beneficial for reducing the quantity of waste, diminishing the negative effects of waste and pollution on the environment, and would be beneficial in bio-converting the waste products into alternate sources of energy. The current chapter focuses on different types of enzymes, their applications for waste management, and their limitations. This chapter also emphasizes the usage of some prominent microorganisms, their secreted enzymes and their proposed mechanisms of action involved with the degradation of the waste products.

The reagents and raw materials used, as well as the products obtained (bio-oil, reaction condensates, polyols and sugar phases) were characterized by elemental analysis, infrared spectroscopy, thermogravimetry and high performance liquid chromatography with mass spectrometry. The heating value of the bio-oils is higher than that of the original biomass (higher heating value of Eucalyptus sawdust bio-oil 29 MJ/kg versus 19.5 MJ/kg of the original Eucalyptus sawdust). The analyses of the bio-oils allowed to identify the presence of high added-value compounds, such as levulinic acid and furfural. Finally, a study of the accelerated aging of the liquefied biomass showed that the biofuel density increases with the storage time due to the occurrence of repolymerization reactions.

Bifunctional catalysts consisting of mono- or bimetallic nanoparticles (NPs) and zeolite supports received considerable attention due to excellent catalytic properties in numerous reactions including direct and indirect biomass processing. Here, we discuss major approaches to the preparation of NPs in zeolites, concentrating on methods allowing the best interplay (synergy) between metal and acid sites which is normally achieved for small NPs well-distributed through zeolite. We focus on modification of zeolites to provide structural integrity and controlled acidity which can be accomplished by incorporation of certain metal ions or elements. The other modification avenue is the adjustment of the zeolite morphology including creation of numerous defects for the NP entrapment and designed porosity. In this review we also provide examples of synergy between metal and acid sites and emphasize that without density functional theory calculations many assumptions about interactions between active sites stay unvalidated. Finally, we describe the most interesting examples of direct and indirect biomass (waste) processing for the last five years.

Cheese whey, a significant byproduct of the dairy industry, poses a substantial environmental challenge due to its organic pollutant load and large size demands for effective and affordable valorization methods. The abundance of lactose and other organic compounds in whey contributes to its elevated Biological Oxygen Demand (BOD) and Chemical Oxygen Demand (COD), further straining natural ecosystems. This study aimed to investigate the nutritional potential of whey and its conversion into value-added products: bioethanol and probiotic drinks. To achieve this, Bacillus megaterium and Bacillus subtilis strains, isolated from soil samples in Nepal, were co-cultured with Lactobacillus and Saccharomyces cerevisiae in the whey broth for fermentation. Ethanol distillation was carried out using a Rota-evaporator to maintain the viability of the fermenting organisms within the broth. Moreover, the probiotic criteria of the fermenting strains were extensively examined. Experimental observations revealed a remarkable concentration of 9.2 g/L of ethanol, resulting in an ethanol yield of 0.23 g/L. Extrapolating this rate, it is theoretically possible to produce an annual global bioethanol output of 5 million tons using whey as a sustainable and abundant resource. Furthermore, the study explores novel advancements in the distillation process, demonstrating the successful extraction of ethanol at room temperature. Additionally, the fermentation organisms employed in this research exhibit robust viability, surviving various in-vitro stress-tolerant tests, including exposure to bile salt, pH fluctuations, and gastric juice. These resilient strains also demonstrated long-term stability in fermented whey broth, making them promising candidates for the development of probiotic beverages. This dual approach not only enables the sustainable management of organic waste but also presents an opportunity to create value-added products with positive implications for both the environment and human health.

Wet anaerobic storage of algal biomass is a promising preservation approach which can ensure continuous supply of these feedstocks to biorefineries year-round. An effective solution to preservation must ensure minimal dry matter loss and change in biochemical composition during storage. Therefore, the objective of this study was to investigate the preservation of Nannochloropsis gaditana biomass through wet anaerobic storage and its impact on biomass quality. Prior to storage, algae sample was inoculated with two different strains of lactic acid bacteria and thereafter stored for 30 and 180 days. Each inoculant limited dry matter loss to &lt;10% (dry basis) after the storage durations. Final pH values (4.3 - 4.8) indicate that the biomass samples were properly ensiled, achieving the acidic conditions necessary for preservation. Compositional analysis of the biomass after storage showed a reduction in carbohydrate content, a relative increase in lipid content, and no significant change to the protein fraction. Glucose and galactose were the prevalent sugar monomers. The low dry matter loss and minimal compositional change indicates that wet anaerobic storage is an effective means of preserving algal biomass, ensuring a constant supply of algal biomass feedstock to a biorefinery.

In the end, this paper analyzed the economy from the investment in plant construction, raw material collection, product production and product sales. The resulting products include pyrolytic carbon, pyrolytic oil, pyrolysis gas. The results showed that when the treatment scale was 1 ton h−1, the pyrolysis plants with three loading modes will always be in a state of loss during the 20-year running time. When the processing scale was 9 ton h−1, the pyrolysis plant can be profitable in the first year. In the sensitivity analysis, the influence of three pyrolysis products on the total return on investment was explored. The results showed that the price change of pyrolysis oil has the greatest influence on the total return on investment (Total ROI) under the three loading methods, The price change of pyrolysis gas has minimal impact on the Total ROI. This study provides basic data and basis for the commercialization of coal-biomass co-pyrolysis technology and investment in plant construction.

Net CO2 emissions and sequestration from European forests are the result of removal and growth of flora. To arrive at aggregated measurements of these processes at a country's level, local observations of increments and harvest rates are up-scaled to national forest areas. Each country releases these statistics through their individual National Forest Inventory using their particular definitions and methodologies. In addition, five international processes deal with the harmonization and comparability of such forest datasets in Europe, namely the IPCC, SOEF, FAOSTAT, HPFFRE, FRA (definitions follow in the article). In this study, we retrieved living biomass dynamics from each of these sources for 27 European Union member states. To demonstrate the reproducibility of our method, we release an open source python package that allows for automated data retrieval and analysis, as new data becomes available. The comparison of the published values shows discrepancies in the magnitude of forest biomass changes for several countries. In some cases, the direction of these changes also differ between sources. The scarcity of the data provided, along with the low spatial resolution, forbids the creation or calibration of a pan-European forest dynamics model, which could ultimately be used to simulate future scenarios and support policy decisions. To attain these goals, an improvement in forest data availability and harmonization is needed.

In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes were investigated, without using any external binding agent. The biomass feedstocks were blended with different ratios of two WEEE plastics (halogen-free wire and print circuit boards (PCB)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10-30%), pressures (22-67 MPa) and temperatures (room-130 ˚C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.

United Nations Framework Convention on Climate Change (UNFCCC) has recently established the Reducing Emissions from Deforestation and forest Degradation (REDD+) program that requires countries to report their carbon emissions and sink estimates through national greenhouse gas inventories (NGHGI). Thus, developing automatic systems capable of estimating the carbon absorbed by forests without in-situ observation becomes essential. To support this important need, in this work we introduce ReUse, a simple but effective deep-learning approach to estimate the carbon absorbed by forest areas based on remote sensing. The novelty of the proposed method is in the use of the public above-ground biomass (AGB) data from the European Space Agency's Climate Change Initiative Biomass project as ground truth to estimate the carbon sequestration capacity of any portion of land on Earth using Sentinel-2 images and a pixel-wise Regressive UNet. The approach has been compared to two literature proposals, using a private dataset and human-engineered features. The results show a greater generalization ability of the proposed approach, with a decrease in Mean Absolute Error and Root Mean Squared Error, respectively, of 16.9 and 14.3 in the area of Vietnam and 4.7 and 5.1 in the area of Myanmar over the runner-up. Finally, as a case study, we reported an analysis made for the Astroni area, a nature reserve located near the metropolitan area of Naples in southern Italy, struck by a large fire, producing predictions consistent with values found by experts in the field. These results further support the use of such an approach for the early detection of AGB variations, both in urban and rural areas.

: Peach processing generates significant amounts of by-products including peels, pomace, and seeds that are often discarded as waste, despite their rich content of bioactive components. Various extraction methods, such as solvent extraction, ultrasound-assisted extraction, and alkaline and acid hydrolysis, have been employed to recover valuable components from peach by-products and repurpose them in various products. These compounds have shown potential applications in the food, pharmaceutical, and cosmetic industries due to their antioxidant, antimicrobial, and anti-inflammatory properties. Furthermore, these wastes can also be used to produce functional ingredients, natural colorants, dietary supplements Alternative uses consist the use as animal feed, as composting materials and biofuels. This comprehensive review provides an overview of the valorization of peach by-products, focusing on their valorization and extraction techniques and potential applications.

The world population increased from 1 billion in 1800 to around 8 billion today. The Population Division of the United Nations predicts a global population of approximately 10.4 billion people by the end of the century. That represents over 2 billion more people. Moreover, the global community is currently experiencing a precarious state due to the enduring repercussions of the COVID-19 pandemic across all sectors, including energy. Given the rising global population and the limited availability of primary energy resources, we must reach a balance between the demands of a growing human population and the planet’s carrying capacity. The dreadful conflict in Ukraine has precipitated an enormous energy crisis. This crisis served as a warning to the world population of how much they depend on this resource to survive. In France, building sectors (i.e., residential and tertiary) alone consume 45% of the final energy disposable. It is the first energy consumer of the country and one of the most polluting (i.e.; about 34% of CO2 emitted by France). Consequently, we must consider alternative energy resource forms (i.e.; substitution energy forms). Harvesting energy from the building envelope may be a viable technique for partially satisfying the electricity demands of building users. In this context, scientific research offers considerable potential for developing more innovative and efficient systems. This article aims to review the state of the art of advances on the subject to orient and further optimize energy production systems, particularly electricity. This work will address several points of view: Discusses the overall backdrop of the present study and introduces the subject ; details the research strategy and procedures used to produce this paper ; develops state of the art on the potential for generating or recovering power from the building envelope ; presents the SWOT analysis of the earlier-described systems. And finally, it concludes by offering findings and viewpoints.

Komagataeibacter spp. have been used for the bioconversion of industrial wastes and lignocellulosic hydrolysates to bacterial cellulose (BC). Recently studies have demonstrated the capacity of Komagataeibacter spp. in the biotransformation of inhibitors found in lignocellulosic hydrolysates, aromatic lignin-derived monomers (LDMs) and acetate. In general, detoxification and BC synthesis from lignocellulosic inhibitors requires a carbon flow from acetyl-coA towards tricarboxylic acid and gluconeogenesis, respectively. However, the related molecular aspects have not yet been identified in Komagataeibacter spp. In this study, we isolated a cellulose producing bacteria capable of synthesizing BC in a minimal medium containing crude glycerol, a by-product from biodiesel production process. The isolate, affiliated to Komagataeibacter genus, synthesized cellulose in minimal medium containing glucose (3.3±0.3 g/L), pure glycerol (2.2±0.1 g/L) and crude glycerol (2.1±0.1 g/L). Genome assembly and annotation identified four copies of bacterial cellulose synthase operon and genes for redirecting the carbon from central metabolic pathway to gluconeogenesis. According to the genome annotations, a BC production route from acetyl-CoA, a central metabolic intermediate, was hypothesized and was validated using acetate. We identified that when K. rhaeticus ENS9b was grown in minimal medium supplemented with acetate, BC production was not observed. However, in presence of readily utilizable substrate, such as spent yeast hydrolysate, acetate supplementation improved BC synthesis.

The paper comes from the need to search for criteria useful for the valorization of heritage towns, located in rural and/or inland areas of Italy, now affected to depression and depopulation process. To this end, the authors point out how territorial identity can constitute the theoretical foundation to influence the development policies and, in particular, the tourism development for sustainability process It was therefore decided to interview a number of stakeholders who could contribute with their professionalism and expertise to identify possible paths and processes for the enhancement of these areas for tourism development. The methodology was based on be to be interviews with open questions, which allowed to identify a SWOT analysis, offering a guideline for a correct governance of these rural areas for their tourist enhancement, in terms of sustainability of development and tourist attractiveness. The study is an observatory that will monitor the implementation of sustainable tourism enhancement of the borghi, heritage town

This work is aimed at the development of innovative, easy and cheap methods for the stabilization, inertization and valorisation of the organic fraction of municipal solid waste (OFMSW). For the first time, two original processes for transforming the organic waste into an inert, odorless and sanitized material were here proposed. The first one, called dual step, starts with grinding of the OFMSW, by means of an industrial shredder. After being finely ground, the organic waste was exposed to a sterilization process by means of UV/ozone radiations or thermal treatment (stabilization phase) in order to obtain a complete removal of the OFMSW’s bacterial activity. By means of several microbiological analyses, the best sterilization method was chosen. The incorporation in a thermosetting matrix was, then, carried out through mixing the sterilized and finely ground organic waste into a water soluble urea formaldehyde (UF) based resin, with a formaldehyde content less than 1% wt, followed by a thermal treatment for UF-resin crosslinking (inertization phase). An alternative cheaper and easier process, called one step, was also proposed and investigated, by combining the sterilization with the curing thermal process (at higher temperature) of the thermosetting matrix. The preliminary experimental results reported in this paper suggest that both the proposed methods could be considered suitable for the production of high valorized innovative OFMSW-derived panels or bricks, that could find application in several fields, such as building or constructions materials. Finally a brief description of the prototype machinery is reported properly designed for implementing OFMSW stabilization and valorisation processes developed in this research work.

Assessing the economic supply of biomass in a geospatial context while accounting for risk from natural disasters was studied. Risk levels were estimated from a component of factors which included: population density, road density, federal ownership, U.S. Environmental Protection Agency ecoregions, and Presidential Disaster Declarations. The Presidential Disaster Declarations included risks due to: coastal storm, drought, fire, flood, freezing, hurricane, mud land slide, severe ices, severe storms, snow, tornado, and tropical storm. Presidential Disaster Declarations included summaries based on a short-term time period from 2000-2011, and on a long-term time period from 1964-2011. Risk categories were developed as a function of the number of disaster declarations, agricultural-to-forest land ratio, average road density, and average population density. A significant contribution of the research was the allocation of spatially explicit data using GIS technology at the 5-digit zip code tabulation area. The average area for 5-digit ZCTAs in the Eastern U.S. study region was approximately 169 kilometers². Long-term risk (1964-2011) from disaster declarations had a greater impact on the economic availability of biomass supply relative to short-term declarations (2000-2011). The greatest risk to biomass supply came from population density relative to the other risk factors studies. Of the 25,044 total ZCTAs, 12,256 ZCTAs were in locations that did not include population density ≥ 150/km², road density ≥ 14 km/km², federal ownership, and US Environmental Protection Agency Level III ecoregions. Of the remaining 12,256 ZCTAs, 26.8% were considered to be moderate-to-high risk based on short-term declarations (2000-2011) and 29.4% were considered to be moderate-to-high risk based on long-term declarations (1964-2011). Lower risk locations for procuring biomass supply for both short-term and long-term declarations, across all risk factors, were in southern Georgia, South Carolina, and Texas.

Microalgae have emerged as potential feed stock for third generation biofuel and other bioactive compounds. In the present investigation we have evaluated the two native strains of Oscillatoria (O. subbrevis MTC-20702 and O. sancta MTC-20703) isolated from two different fresh water biotopes of Meerut, U.P., India and were subjected for the characterization of generation time, biomass, bio-molecules including Chlorophyll-a, carotenoids, carbohydrate, lipids, phycobilins and proteins. Both strains of Oscillatoria were grown in batch culture till the initiation of declining phase and were harvested on every 10th day of incubation till the starting of declining phase. Result of the present investigation revealed that O. subbrevis MTC-20702 can be potentially exploited for the production of high algal biomass, feed stock for biofuel, Chl-a, carotenoids, c-Allophycocyanin and maximum yield of these bioactive compounds can be achieved on 20th day. However, O. santa could be very good source for c-Phyocyanin, c-Phycoerythrin, carbohydrate and protein and these also can be achieved highest on 20th day of incubation. In addition, as these two strains were isolated from water reservoirs and they can be cultivated in large scale for the production of desired bio-molecules.

The emergence of cloud computing, big data analytics, and machine learning has catalysed the use of remote sensing technologies to enable more timely land management of sustainability indicators such as ground cover and grassland biomass, given the uncertainty of future climate and drought conditions. Here, we examine the potential of “regenerative agriculture”, as an adaptive grazing management strategy to minimise bare ground exposure while maximising pasture biomass productivity. High-intensity sheep grazing treatments were conducted in small fields (less than 1 hectare) for short durations (typically less than 1 day). Paddocks were subsequently spelled to allow pasture biomass recovery (treatments comprising 3, 6, 9, 12, and 15 months) with each compared with control treatments with lighter stocking rates for longer periods (2,000 DSE). Pastures were composed of wallaby grass (Austrodanthonia species), kangaroo grass (Themeda triandra), Phalaris (Phalaris aquatica, and cocksfoot (Dactylis glomerata) were destructively sampled to estimate total standing dry matter (TSDM), standing green biomass, standing dry biomass and trampled biomass. We then invoked a machine learning model using Sentinel-2 imagery to quantify TSDM, standing green biomass and standing dry biomass. Faced with La Nina conditions, regenerative grazing did not significantly impact pasture productivity, with all treatments showing similar TSDM and green biomass. However, regenerative treatments significantly impacted litter fall and trampled material, with the high intensity grazing treatments causing more dry matter trampling, increasing litter, enhancing decomposition rates and surface organic matter. Pasture digestibility was greatest for treatments with minimal spelling (3 months), whereas both standing senescent and trampled material were significantly greater for the treatment with 15-month spell periods. Estimates of TSDM using machine learning with Sentinel-2 imagery underestimated TSDM in treatment plots but explained spatiotemporal variability associated within and across treatments. The root mean square error between the measured and modelled TSDM was 903 kg DM/ha, which was less than the variability measured in the field. We conclude that regenerative grazing with short recovery periods (3-6 months) are most conducive to increasing pasture production under high rainfall conditions, and we speculate that high intensity grazing is likely to positively impact on soil organic carbon through increased litterfall and trampling. Our study paves the way forward for using machine learning with satellite imagery to quantify pasture biomass at small scales, enabling management of pastures from afar.

Pyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article focuses mostly on recent achievements in the technical and processing aspects of pyrolysis. This review provides an overview of the recent advanced pyrolysis technology used in gas, bio-oil, and biochar production. The key parameters to maximize the production of specific chemical compounds were discussed and considered during the construction of the reactors. The emphasis is put on optimizing the process parameters, technical requirements, and renewable energy use in the process and conception to improve the efficiency of product production. The application of pyrolysis gas, oil, and biochar as valuable chemical compounds are related to the intensifying effects of climate change, biofuel production, and waste management in accordance with the principles of sustainable development.

The purpose of this work is to define optimal growth conditions for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on algae growth: i.e., inoculum:culture medium ratio, light:darkness photoperiod and type of culture medium, including both synthetic media and wastewaters. The results showed that the initial inoculum volume did not affect the amount of biomass at the end of the growth (14 days), whereas an excess (18 h) or defect (6 h) in the number of hours of light is determinant for its development. The contribution of nutrients from different culture media modified the growth of the different species. A. maxima was favoured in seawater enriched with Guillard's F/2 as well as C. vulgaris and N. gaditana but in fresh water medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrate was the limiting growth reagent at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalgae species.

There is a growing demand for clean-label products. This study aimed to obtain a food-grade coloring ingredient for meat products based on the formation of Zn-protoporphyrin from porcine livers, thus contributing to the development of nitrite-free products. First, the effects of sodium disulfite, and acetic, ascorbic, and lactic acids on Zn-protoporphyrin formation and total microbial count were studied. The combination of ascorbic and acetic acid resulted in a higher Zn-protoporphyrin content than acetic acid alone and maintained microbial levels (ca. 3 log CFU/mL). Second, a response surface methodology was used to maximize Zn-protoporphyrin while maintaining microbiological food standards. The effects of pH (4.2–5.4), incubation time (3–30 h), and temperature (25–50 ºC) were studied. The selected conditions for Zn-protoporphyrin formation involved anaerobic incubation at pH 4.8 and 45 °C for 24 h. The safety was validated through challenge testing for relevant pathogens (Listeria monocytogenes, Salmonella spp., and Clostridium perfringens). A significant reduction (&gt; 6 log units) was observed for L. monocytogenes and Salmonella, whereas C. perfringens spores remained at inoculated levels. The optimized procedure is proven to be microbiologically safe, and it is proposed to improve the color of nitrite-free meat products.

This study aims to analyze various types of pellet fuels used as energy sources in Bulgaria, focusing on their energy characteristics and the consumer preferences. Both standard and specialized methods such as thermogravimetry (TG) and differential scanning calorimetry (DSC) are used for the analyses. The results from TG and DSC indicate that during the drying of the samples, moisture is evaporated from their surface, along with the release of volatile substances. The processes during the analysis are accompanied by energy absorption, with the main stage being combustion, where the primary amount of heat is generated. Standard analysis methods show that wood pellets usually contain about 7.31% moisture, 0.72% ash and have a calorific value of 18.33 kJ/kg, while sunflower pellets contain about 7.62% moisture, 2.42% ash and have a calorific value of 19.63 kJ/kg. Mixed pellets contain about 7.07% moisture, up to 0.69% ash and have a calorific value of 18.05 kJ/kg. A specialized marketing research was conducted to investigate consumer attitudes and preferences toward purchasing different types of solid biomass fuels on Bulgarian market. This study provides information on the quality of pellets as fuel by offering a detailed analysis of their fuel properties and ensuring their effective utilization as an energy source.

Chlorella vulgaris has considerable promise as a raw material for biofuel production since it has a high productivity per unit area, has a minimum influence on the environment, and does not significantly affect food security. Nevertheless, the low fatty content of their biomass poses a considerable economic obstacle for commercialization. Increasing the amount of biomass and lipids produced by these algae is essential for improving the economic feasibility of using them as biofuel sources. This review highlights the significance of identifying appropriate algal strains, namely those found in local environments, and utilising mutagenesis and genetic engineering techniques to create 'platform strains'. Prior endeavours have primarily concentrated on altering environmental and dietary parameters to enhance the production of biomass and lipids. Here, we review a scientific literature that examines biotechnological approaches and develops methodologies designed to increase lipid production, emphasising the importance of aligning engineering efforts with breakthroughs in DNA manipulation tools. In addition, the review research evaluates the present economic and commercial situation of algal biorefineries, including any related disadvantages. In summary, this thorough research highlights the importance of using creative methods to tackle the intricacies of lipogenesis and enhance the economic viability of producing biofuels from algae.

In terms of sustainability, there is a pressing need to evaluate agricultural and forestry leafy biomass that has no current economic value or may pose a threat to the environment. In this aspect, leafy biomass, which represents around 5% of the total tree, can be used for purposes that would be more profitable and ecofriendly. To this end, biorefinery of leafy biomass in the way of extracting valuable health compounds such as phenolics would ensure a valuable societal health ingredient besides alleviating waste disposal problem. However, during the biorefinery process, the primary challenges start with ensuring the feedstock to produce phenol rich leaves extract followed by their isolation and commercialization of this leaves extract. This current review aims to detail the types of biomasses, biorefinery approach of leafy biomass towards the phenolic extraction, leaves commercialization followed by the marketing strategy of the application of phenol rich leaves extract. The outcome of this overview will serve researchers and relevant industries in understanding the process for feedstock collection and the suitable sectors to apply leafy biomass derived healthy compounds.

Pyrolysis is a thermochemical conversion process designed for biomass decomposition in an oxygen-free environment. It typically operates within a temperature window of 200 to 800°C and generates various byproducts, including gases, liquid fractions (both aqueous and organic) such as bio-oil, and solids like char. Bio-oil is a significant product of pyrolysis. It is characterised by a complex blend of organic compounds. The acidic nature of bio-oil primarily originates from volatile acids, such as acetic acid. The recovery of acetic acid from bio-oil facilitates the use of the extracted substance as a precious resource, hence enhancing its significance in the framework of a circular bioeconomy. Acetic acid finds widespread application in manufacturing commercially important chemicals like vinyl acetate monomers and formulating phytosanitary products due to its inherent herbicidal and antifungal properties. However, to be used, acetic acid has to be separate from the raw bio-oil. Separation methodologies, including nanofiltration and reverse osmosis, demonstrate potential in recovering acidic constituents from bio-oil due to their high selectivity and effective system management. This article offers a concise review about acetic production from lignocellulosic biomass from pyrolysis and its recovery through various membrane separation processes.

The exploitation of bio-based foams implies an increase in the use of renewable biological resources to reduce the rapid consumption of petroleum-derived resources. Both tannins and furfuryl alcohol are derived from forestry resources and are therefore considered as attractive precursors for the preparation of tannin-furanic foams. In addition, toughening modification of tannin-furanic foams using polyvinyl alcohol (PVOH) resulted in a more flexible network-like structure, which imparts excellent flexibility to the foams with acquirement of relative properties that are even close to those of polyurethane foams, which are the most used polymers for fabrication of insoles for athletes. In addition, the addition of PVOH did not affect the thermal insulation of the foams, resilience and elongation at break, while reducing the brittleness of the samples and improving the mechanical properties. Also the observation of the morphology of the foam indicated that the compatibility between PVOH and tannin-furanic resin is good, and the cured foam does not show fragmentation or collapse, while the bubble pore structure is uniform. The developed flexible foam derived from biomass resources endowed the foam good thermal insulation properties and high mechanical properties, and the samples exhibited suitable physical parameters to be used as flexible insoles for athletes.

The aim of this research was to test recent developments in the use of Remotely Piloted Aircraft Systems or Unmanned Aerial Vehicles (UAV) to map pasture biomass yield and nutrient status, across a selected range of field sites throughout the rangelands of Queensland. Improved pasture management begins with an understanding of the state of the resource base, UAV based methods can potentially achieve this at improved spatial and temporal scales. This study developed predictive models of both pasture yield and pasture nutrient status. An automated pasture height surface modelling technique was developed, tested and used along with field site measurements of pasture yields, to predict further estimates across each field site. Both prior knowledge and automated predictive modelling techniques were employed to predict pasture yield and nutrition. Pasture height surface modelling was assessed against field measurements using a rising plate meter, results reported correlation coefficients (R2) ranging from 0.2 to 0.4 for both woodland and grassland field sites. Accuracy of the predictive modelling was determined from further field measurements of pasture yield and on average indicated an error of 0.8 t ha-1 in grasslands and 1.3 t ha-1 in mixed woodlands across both modelling approaches. Correlation analyses between measures of pasture quality, acid detergent fibre and crude protein (ADF, CP), and spectral reflectance data indicated the visible red (651 nm) and red-edge (759 nm) regions were highly correlated (ADF R2 = 0.9 and CP R2 = 0.5 mean values). These findings agreed with previous studies linking specific absorption features with grass chemical composition. These results conclude that the practical application of such techniques, to efficiently and accurately map pasture yield and quality, is possible at the field site scale, however further research is needed, in particular further field sampling of both yield and nutrient elements across such a diverse landscape, with the potential to scale up to a satellite platform for broader scale monitoring.

The present article discusses the institutional model adopted in Brazil regarding energy production through biomass. The theoretical-empirical method is used to conclude that the model's difficulties can be overcome by adopting a network of contracts capable of subjecting renewable energy generation to an energy compensation model.

The case for demand-driven research and development has received important considerations among governments, donors and programme implementing partners in development planning and implementation. Addressing demand is believed to be a bottom-top approach for designing and responding to development priorities and is good for achieving development outcomes. In this paper, we discuss the concept and application of demand driven research for development (DDRD) in Africa. We use evidence of six projects implemented under the BiomassWeb Project in Africa. We focus on parameters on level of engagement of stakeholders - whose demand is being articulated, the processes for demand articulation, capacity building and implementation processes, innovativeness of the project, reporting and sustainability of the project. We find that the nature of the institutions involved in articulation and implementation of demand-driven research and development projects and their partnerships influence the impact and reporting of demand-driven projects.

According to the IPCC guidelines, CO₂ emissions from biomass should be excluded from the entire amount of CO₂ emissions when calculating CO₂ emissions and should be separately reported due to the “carbon neutrality.” Sewage sludge is one of the representative biomass fuels. And it is mixed with fossil fuels in terms of greenhouse gas reduction or is used as fuel to replace fossil fuels by itself. According to the results of this study, biomass contents of both the sewage sludge and the sewage sludge incineration exhaust gases did not amount to 100%. At present, in many countries(South Korea, Japan, and Germany), when calculating greenhouse gas emissions from sewage sludge incinerator, all CO₂ emissions from sewage sludge are judged to be biomass and only those greenhouse gas emissions that correspond to Non-CO₂ gases are calculated as greenhouse gas emissions. However, since, according our results, the content of sewage sludge is not 100% biomass, if CO₂ emissions are excluded according to the existing greenhouse gas emission calculation method, the amount of emissions may be underestimated. Therefore, to accurately calculate greenhouse gas emissions from sewage sludge incinerator, CO₂ emissions should be calculated in consideration of the fossil carbon contents of sewage sludge.

The cultivation of pea pods spans across various regions and climates with a global production of around 20 million tons. The pea peel wastes, which make up 30–40% of the total weight of the peas, are freely available in large quantities. The biomass used was characterized via ultimate, proximate, and structural analysis obtaining a 20,2 %w of cellulose and 17,4 %w of hemicellulose which via valorization processes can be transformed into platform chemicals. Hydrothermal valorization presents itself as a clean form of treatment of said wastes, ranging from 120 – 180 ºC (LHW) to 180 to 260 ºC (HTC). The use of LHW can lead to the production of sugars (up to 70%w yield) and levulinic acid (4 %w yield) while the use of HTC leads to Formic acid (40 %w) and levulinic acid (4 %w yield). The use of LHW for longer times favors the production of HMF and Furfural. The use of homogeneous catalysts (H2SO4, CH3COOH, KOH and NaHCO3) was implemented and their selectivity described. Solid fractions of LHW and HTC were characterized via FTIR and elemental analysis and the change in their structure described as they shift from biomass to biochar. Optimal conditions for each platform chemical were reported for best utilization of the peapod waste.

Food security relies mainly on a few major crop such as wheat, maize, rice and yam. Many of the cultivated plant such as Cyperus exculentus are still considered invasive plants and are neglected and underutilized. In the perspective to valorization of the species, this systematic review aimed at identifying the biology, production constraints and uses of tigernut for future research directions. Extensive searches were carried out and studies were screened and extracted using established systematic review methods. A total of 175 papers met the inclusion criteria. Approximately 52% and 21.71% of the studies were undertaken in Europe and Africa respectively. Most of the papers reviewed for the study were published between [2010-2015[. The review highlighted the critical research gaps in genetic diversity using SSR makers and evolutionary biology. Further, production constraints and solution approaches for the promotion of the species were the other gaps identified in the reviewed studies. Production constraints were specifically related to the insufficient mineral fertilizers and difficult in harvesting. Tigernut is used in more fields such as food, medicinal, cosmetic, biofuel and fishing and fish breeding. Such investigations would help in decision-making and elaboration of breeding strategies, and advancing steps towards sustainable use of the species.

Lake Malombe fish stocks have been depleted by chronic overfishing. Various management approaches (co-management, command control, and ecosystem-based management to fisheries) have been used to manage the fishery. However, the lack of an accurate predictive model has hampered their success. Therefore, we developed and tested a time series model for Lake Malombe fishery. The seasonal fish biomass and CPUE trends were first observed and both were non-stationary. The second-order differencing was applied to transform the non-stationary data into stationary. Autocorrelation functions (AC), partial autocorrelation function (PAC), and Akaike information criterion (AIC) were estimated, which led to the identification and construction of autoregressive integrated moving average (ARIMA) models, suitable in explaining the time series and forecasting. The results showed that ARIMA (1,2,1) provided a better prediction than its counterparts. The model satisfactorily predicted that by 2032, both fish biomass and CPUE will decrease to 3204.6 tons and 59.672 respectively, signifying the potential threat to Lake Malombe fishery. The model justified the necessity of taking precautionary measures to avoid the total collapse of the fishery.

Based on recent interest and on the importance of the ongoing climate change catastrophe, this article provides the basics of global carbon cycle modelling as required for the assessment of the degree of carbon neutrality of biomass energy, and its underlying dynamics. It is aimed at clari-fying the question “Are biomass fuels carbon neutral?”. The "Combined Energy and Biosphere Model" (CEBM) computes annual carbon flows including growth and decay of plants on 2.52.5° grid elements of the continents’ surface and offers detailed results on the changes of after implementation of large-scale biomass energy strategies world-wide. The main (and possibly unexpected) effect is the long-term depletion of the soil organic compartment after extraction of biomass fuels. When comparing CEBM model runs using (i) biomass energy sources and (ii) carbon-free energy sources (such as solar or wind), it becomes quantitatively clear already on the theoretical level (i.e., even without taking into account effi-ciency losses) that biomass is only “half as carbon neutral” as ideally assumed, to express a rule of thumb – mainly because of soil carbon depletion. Still, biomass energy will play an important role when fighting global warming, even if efforts to lower energy demand are preferable as a fundamental strategy.

Biomass gasification acquired great interest over the past decades as an effective and trustable technology to produce energy and fuels with net-zero carbon emissions. Moreover, using biomass waste as feedstock enables to recycle organic wastes and to fit the circular economy goals thus reducing the environmental impacts of waste management. Even if many studies have been already carried on, this kind of process must still be investigated and optimized with the final aim to develop industrial plants for different applications, from the hydrogen production to net-negative emission strategies. Modeling and developing of process simulations became an important tool to investigate the chemical and physical behavior of the plant, allowing to make a first raw optimization of the process and to define heat and material balances of the plant as well as to define optimal geometrical parameters with cost and time effective approaches. The present review paper focuses on the main literature models developed until now to describe biomass gasification process, and in particular on kinetic models, thermodynamic models, and computational fluid dynamic models. The aim of this study is to point out the strengths and the weakness of those models, comparing them and indicating in which situation is better to use an approach instead of another. Moreover, theoretical shortcut models and software simulations, not explicitly addressed by prior reviews, are taken into account. For researchers and designers this review provides a detailed methodology characterization as a guide to develop innovative study or project.

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

Chaparral shrublands are the dominant wildland vegetation type in southern California and the most extensive ecosystem in the state. Disturbance by wildfire and climate change have created a dynamic landscape in which biomass mapping is key in tracking the ability of chaparral shrub-lands to sequester carbon. Despite this importance, most national and regional scale estimates do not account for shrubland biomass. Employing plot data from several sources, we built a random forest model to predict above ground live biomass in southern California using remote sensing data (Landsat NDVI) and a suite of geophysical variables. By substituting the NDVI and precipi-tation predictors for any given year we were able to apply the model to each year from 2000-2019. Using a total of 980 field plots, our model had a k-fold cross validation R2 of 0.51 and a RMSE of 3.9. Validation by vegetation type ranged from R2 = 0.17 (RMSE=9.7) for Sierran mixed conifer to R2 = 0.91 (RMSE = 2.3) for sagebrush. Our estimates showed an improvement in accuracy over a two other biomass estimates that included shrublands, with an R2 = 0.82 (RMSE = 4.7) compared to R2 = 0.068 (RMSE = 6.7) for a global biomass estimate and R2 = 0.29 (RMSE = 5.9) for a regional biomass estimate. Given the importance of accurate biomass estimates for resource managers we calculated the mean year 2010 shrubland biomass for the four national forests which ranged from 3.5 kg/m2 (Los Padres) to 2.3 kg/m2 (Angeles and Cleveland). Finally, we compared our estimates to field-measured biomass from the literature summarized by shrubland vegetation type and age class. Our model provides a transparent and repeatable method to generate biomass measure-ments in any year, thereby providing data to track biomass recovery after management actions or disturbances such as fire.

Many corporations aspire to become Net Zero Carbon Dioxide by 2030-2050. This paper examines what it will take. It requires understanding where energy is produced and consumed, the magnitude of CO2 generation, and the Carbon Cycle. Reviews are provided for prior technologies for reducing CO2 emissions from fossil to focus on their limitations and to show that none offer a complete solution. Both biofuels and CO2 sequestration reduce future CO2 emissions from fossil fuels. They will not remove CO2 already in the atmosphere. Planting trees has been proposed as one solution. Trees are a temporary solution. When they die, they decompose and release their carbon as CO2 to the atmosphere. The only way to permanently remove CO2 already in the atmosphere is to break the Carbon Cycle by growing biomass from atmospheric CO2 and sequestering biomass carbon. Permanent sequestration of leaves is proposed as a solution. Leaves have a short Carbon Cycle time constant. They renew and decompose every year. Theoretically, sequestrating a fraction of the world’s tree leaves can get the world to Net Zero without disturbing the underlying forests. This would be CO2 capture in its simplest and most natural form. Permanent sequestration may be achieved by redesigning landfills to discourage decomposition. In traditional landfills, waste undergoes several stages of decomposition, including rapid initial aerobic decomposition to CO2, followed by slow anaerobic decomposition to methane and CO2. The latter can take hundreds to thousands of years. Understanding landfill chemistry provides clues to disrupting decomposition at each phase.

This study compares the physico-chemical characteristics of three different types of biochar produced from biomass residues in Vietnam as a basis for optimising their application in water purification and soil fertilisation. Wood biochar (WBC), rice husk biochar (RBC), and bamboo biochar (BBC) were produced under limited oxygen conditions using equipment available locally in Vietnam, known as a Top-Lid Updraft Drum (TLUD). The resulting biochars were characterised using a suite of state-of-the-art methods to understand their morphology, surface chemistry and cation exchange capacity. Surface areas (measured by BET) for WBC and BBC were 479.34 m²/g and 434.53 m²/g, respectively, significantly higher than that of RBC which was only 3.29 m²/g. The morphology as shown in SEM images corresponds with the BET surface area, showing a smooth surface for RBC, a hollow surface for BBC, and a rough surface for WBC. All three biochars produced alkaline, with pH values around 10, and all have high carbon contents (47.95 - 82.1 %). Cation exchange capacity (CEC) was significantly different (p<0.05) among the biochars, being 26.70 cmol/kg for RBC, 20.7 cmol/kg for BBC, and 13.53 cmol/kg for WBC, which relates to the cations (Ca, Mg, K) and functional groups with negative charge (carboxyl, hydroxyl) present on the biochar surfaces. The highest contents of Ca, Mg and K in rice husk BC may explain its highest CEC values. Thus, although the biochars were produced by the same method, the various feedstocks lead to quite different physico-chemical properties. Ongoing work is linking these physico-chemical properties to the biochar efficiencies in terms of nitrate and ammonia capture capacities for use as fertilisers, and for adsorption of heavy metals (Zn, Cu) or water filtration, in order to design optimal biochar properties for specific applications.

The military areas in Sardinia are around 234 km2, which constitutes 59.97% of the national surface affected by military easements. This situation is due to its geographic centrality in the Mediterranean. This contribution evaluates the performance of the Local Coastline Plan (LCP) and the Site Management Plan of Community Interest (SCI) in conditions of military constraint. The case study is the Municipality of Villaputzu where an important coastal military easement and the use of the coast for recreational tourism purposes coexist together through specific planning, a consequence of institutional agreements between the Municipal Administration of Villaputzu and the Ministry of Defense. The evaluation of the congruence of the specific objectives of the LCP and the SCI shows how their combined action favors the environmental enhancement of Sardinia, contributing to the formation of ecosystem services, even in particular conditions arising from military easements. These are sites that pass from the status of "anti-commons" to "semi-commons". In fact, the military release process in Sardinia, together with the promiscuous military and civil use, activates unique governance policies of their kind that find a significant field of application in Sardinia to guarantee a sustainable renewal of economic development of the ‘semi-commons’ awaiting to become ‘commons’

Distinguishable annual growth rings produce in Pinus roxburghii are an asset to find out the age of individual tree. This paper aimed to determine the age of P. roxburghii through coring samples and test the relationship with forest production. The biomass estimated, girths measured at two different sections and heights measured which allowed to determine the rate of tapering of the stand. The regression analysis was performed to test the relationship between various variables. The mean age of the P. roxburghii stand was found to be 23.97 (~24 years). The result showed the significant (p<0.05) positive correlation coefficient has been seen between age with girth at breast height, biomass, volume and carbon stock. However, no significant (p>0.05) correlation (r = 0.08) was found between age and height of the stand. In contrast, a correlation between diameter at breast height (DBH) was significant (p<0.05) and positive with volume, biomass, but no significant (p>0.05) correlation (r = 0.14) found between DBH and height of the stand. However, height has a significant (p<0.05) positive correlation with biomass. The mean biomass was 375 kg and mean annual increment (MAI) was 15 kg per tree. Rate of tapering of the studied stand predicted to be 3 cm diameter decreased with trunk height running at 100 cm from base to upward of P. roxburghii stand and vice versa. Result suggests that height-age relation is very weak whereas age, DBH, biomass and carbon has a significant correlation signifies that time-based forests' production and potential production estimation can be obtained in a relatively accurate way by utilizing the age of stand. The time-based forest production analysis is pioneer work in Nepal. The study affirms the tree ring count in P. roxburghii would be a credible and accurate method to determine the age of standing trees.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T1 = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T2 = 50 kg N ha^-1, T3 = 100 kg N ha^-1 and T4 = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T5: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T6: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T7: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO2 concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T6 = Split N100) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

In an increasingly resource-constrained era, the utilization approach of waste and by-products from grain processing, is attractive widely, considering both nutritive value and economic aspects and move towards more sustainable food systems. Following the fundamentals of a circular economy, the need of the hour lies in its effective utilization as a grain waste and by-products conversion into value-added products in food industry. The aim of this study is twofold: 1. Understanding the progress of grain waste and by-products to valorization in human nutrition, using bibliometrics; different literature databases namely Google Scholar, Web of Science and Elsevier Scopus have been evaluated for their merits and values; 2. Exploration of knowledge-based strategies, by reviewing the literature concerning the possible use of grain waste and by-products for food processing industry, reducing burden on virgin raw materials. The review allowed to unlock the latest-advances of upcycling side streams and waste from grain processing industry.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

Biogeochemical models estimate soil organic carbon (SOC) sequestration, crop growth, and yield. The DeNitrification and DeComposition (DNDC) model was used to simulate soil SOC dynamics and harvested C-biomass in rice-wheat rotation under organic/inorganic fertilizations with conventional tillage (CT) and reduced tillage (RT). Before calibration, DNDC under-predicted harvestable grain C-biomass of rice by 29.22% to 42.14% and over-simulated grain C-biomass of wheat by 55.01% with equal amounts of NPK and animal manure applied under CT. However, after calibration by adjusting default values of soil/crop parameters, DNDC simulated harvestable grain C-biomass of both crops very close to observed values (only -2.81% to -6.17% less). DNDC also predicted effects of nutrient management practices on grain C-biomass of rice/wheat under CT/RT using d-index (0.76 to 0.96) and the calculated root mean squared error (RMSE of 165.36 to 494.18 kg C ha-1). DNDC simulated SOC trends for rice-wheat using measured values of several statistical indices. Regression analysis between modeled and observed SOC dynamics was significant with R2 ranging from 0.35 to 0.46 (p < 0.01), and intercept ranging from 0.30 to 1.34 (p < 0.65). DNDC demonstrated that combined inorganic and organic fertilization may result in higher C-biomass and more SOC sequestration in rice-wheat systems.

The Opuntia ficus-indica (OFI) prickly pear peel, is a residue product and was used as a substrate in solid-state fermentation (SSF) to obtain bioactive compounds of interest due to its antimicrobial and antioxidant activity. A Box Hunter &amp; Hunter design to evaluate the independent factors was used. These factors were temperature (°C), inoculum (spores/g), humidity (%), pH, NaNO3 (g/L), MgSO4 (g/L), KCl (g/L) and KH2PO4 (g/L). The response factors were hydrolyzable and condensed tannins amount. In addition, the fermentation extracts the antioxidant and antimicrobial activity were evaluated. The results showed that the humidity (%), inoculum (spores/g) and temperature (°C) affect the release of hydrolyzable and condensed tannins. The treatments 13 and 16 were the best to accumulate condensed (43 mg/g) and hydrolyzable tannins (3.8 mg/g) respectively. Besides, the fermented extracts showed a higher antioxidant activity compared than the unfermented peel extracts, as well as a high inhibition versus E. coli, Alternaria sp. and Botrytis spp. The use of the fermentation process is a good alternative for the recovery of waste and the accumulation of bioactive molecules with potential industrial application.

Recently, the difficulties in recycling and environmental pollution caused by metal-based electrode materials have limited the further development of batteries. Therefore, biomass carbon materials, with their environmental friendliness and stable performance, are the key to solving this problem. Many advances have been achieved by researchers for the application of biomass porous carbon materials in batteries. Nevertheless, the same biomass carbon materials in batteries face problems such as low utilization, low yield, and a cumbersome preparation process. This paper thus aims to summarize the recent progress of biomass carbon materials in the field of batteries and provide a detailed description of the battery performance of biomass carbon materials from three perspectives: synthesis, structure and application of carbon materials. We believe that biomass carbon composites are in line with future development and have a broad application prospect. Finally, we will give our in-depth prospect on developing biomass carbon materials.

The microorganisms able of accumulating lipids in high percentages, known as oleaginous microorganisms, have been widely studied as an alternative for producing oleochemicals and biofuels. Microbial lipid, so called Single Cell Oil (SCO), production depends on several growth parameters, including the nature of the carbon substrate, which must be efficiently taken up and converted into storage lipid. Οn the other hand, substrates considered for large scale applications must be abundant and of low acquisition cost. Among others, lignocellulosic biomass is a promising renewable substrate containing high percentages of assimilable sugars (hexoses and pentoses). However, it is also highly recalcitrant and therefore it requires specific pretreatments in order to release its assimilable components. The main drawback of lignocellulose pretreatment is the generation of several by-products that can inhibit the microbial metabolism. In this review, we discuss the main aspects related to the cultivation of oleaginous microorganisms using lignocellulosic biomass as substrate, hoping to contribute to the development of a sustainable process for SCO production in the near future.

Carbohydrate composition of lignocellulosic biomass is one of the main factors for production of biofuel from the plant biomass. Various methods like Thermogravimetric analysis (TGA), near infrared spectroscopy (NIR) often used in determination of polysaccharide component of the plant biomass. However, used of such tools is based on the prediction and very costly. This paper discussed about the determination of carbohydrate composition (cellulose, hemicellulose and lignin) using the automatic fibre estimation system. The protocol was developed for the estimation of cellulose, hemicellulose and lignin component of lignocellulosic biomass. This protocol explains a simple method to estimate the polysaccharide component of lignocellulosic biomass. This protocol can be used not only lignocellulosic biomass but also for other hardwood biomass. The advantages and techniques, procedures are presented below.

Antioxidant activity is an essential feature required for oxygen-sensitive merchandise and goods, such as food and corresponding packaging as well as materials used in cosmetics and biomedicine. For example, vanillin, one of the most prominent antioxidants, is fabricated from lignin, the second most abundant natural polymer in the world. Antioxidant potential is primarily related to the termination of oxidation propagation reactions through hydrogen transfer. The application of technical lignin as a natural antioxidant has not yet been implemented in the industrial sector, mainly due to the complex heterogeneous structure and polydispersity of lignin. Thus, current research focuses on various isolation and purification strategies to improve the compatibility of lignin material with substrates and enhancing its stabilizing effect. This contribution presents antioxidant capacity studies of various lignins depending on purification degree of the raw material. In detail, the antioxidant potential of lignin-based compounds is studied using the DPPH (2,2-diphenyl-1-picrylhydrazyl) assay. The purification procedure was monitored by thin layer chromatography (TLC) and showed that double-fold selective extraction is the most efficient purification procedure (confirmed by UV-Vis, FTIR, HSQC and 31P NMR spectroscopy, SEC and XRD analysis). Results are discussed regarding the dependency of antioxidant activity on lignin structure and biomass source. Thus, lignins obtained from industrial black liquor are compared with beech wood samples. In addition, the influence of lignin isolation (kraft versus organosolv) is discussed. Values of the antioxidant activity (DPPH inhibition) of kraft lignin fractions were 62-68% while beech and spruce/pine-mixed lignins showed values between 26, 64 and 42%, respectively. TPC values of the different isolated kraft lignin fractions varied between 26-35%, while beech, spruce/pine lignins were 34, 30 and 34%, respectively. Storage decreased the TPC values and increased the DPPH inhibition.

Malaysia generates significant quantities of Oil Palm Wastes (OPW) which can be potentially valorised into sustainable bioenergy as envisaged by the National Biomass Strategy (NBS-2020). Despite significant investments, policy directives and government support, the valorisation of OPW into bioenergy has remained low exacerbating waste management challenges. Therefore, the strategies and impediments to the rapid bioenergy development and bioelectricity generation from OPW require practical assessment. Therefore, this paper examines the level of development and diffusion of the biomass innovation system in Malaysia based on the Functions of Innovations Systems (FIS) approach developed by Dutch and Swedish researchers. Furthermore, the key factors hindering biomass energy technologies implementation in Malaysia and potential solutions were identified, highlighted and examined. Based on the FIS analysis the functions; entrepreneurial activities, knowledge development, and resources mobilization functions are well established in the Malaysian biomass innovation system (BIS). However, the functions of guidance of search; creation of legitimacy; knowledge diffusion and market formation are underdeveloped resulting in the low penetration of bioenergy in Malaysia. Other factors include; fossil fuel subsidies, numerous or conflicting energy policies and weak collaboration between academia and the industry. The outlined challenges can be addressed by revising fuel subsidies, Feed-in tariffs, RETs implementation, roles of supervisory agencies, and bureaucratic procedures for access to funds for research and development of bioenergy in Malaysia.

Eryngium foetidum L., a biennial herb with diverse applications in food and traditional medicine, holds economic and pharmacological significance. Given its growing commercial interest, implementing biotechnological approaches like plant tissue culture is vital for sustainable propagation and metabolite production. In this study, we investigated the in vitro photoautotrophic potential of E. foetidum, examining growth, chlorophyll a fluorescence, photosynthetic pigments, and anatomical features under different sucrose concentrations and gas exchange rates. Acclimatization and survival rates of plants after ex vitro transfer were also assessed. E. foetidum exhibited robust growth in both photoautotrophic and photomixotrophic conditions, with natural ventilation significantly enhancing plant development. Chlorophyll a fluorescence and photosynthetic performance were influenced by sucrose and gas exchange, highlighting the importance of these factors in plant micropropagation. Moreover, the species demonstrated remarkable plasticity during acclimatization, with high survival rates and rapid inflorescence emission. The research provides valuable insights into optimizing in vitro cultivation conditions for E. foetidum, emphasizing the potential for large-scale clonal propagation and exploring secondary metabolites. The observed phenotypic plasticity underscores the adaptability of the species to diverse environments. These biotechnological strategies open avenues for future studies, including the application of elicitors for enhanced secondary metabolite production.

Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six case scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt– 72 kt/year. Scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with about 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period and was found to be sensitive to variations in feedstock cost.

Dipteryx spp. is an important species in reforestation in the Amazon. The objective of this study is to characterize and compare the relationships between dendrometric variables in Dipteryx spp. stands in the Western Amazon by fitting linear regression equations for total height and crown diameter. Six forest stands were evaluated in three municipalities. Dendrometric variables collected included diameter at 1.3 m height (dbh), total height (ht) and crown diameter (dc). Simple and multiple linear regression equations were fitted to characterize the relationships between ht and dc. The total aboveground biomass of Dipteryx spp. trees and the carbon stock of the stands were estimated. The general equations showed higher R² values, exceeding 0.7. The general equations for estimating ht and dc were significant for all coefficients. The trees averaged 22 t/ha of aboveground biomass in the stands. There was a variation in carbon sequestration potential among stands, ranging from 5.12 to 88.91 t CO2.ha-1. Single-input equations using dbh as an independent variable are recommended for estimating dc and ht for individual Dipteryx spp. stands. Stands in the Western Amazon play a significant role in carbon sequestration and accumulation. Trees can sequester an average of 4.8 tons of CO2 per year.

Recently, the move from cost-tied to open-access data has led to the mushrooming of research in pursuit of algorithms for estimating aboveground grass biomass (AGGB). Nevertheless, a comprehensive synthesis or direction on the milestones archived or an overview of how these models perform is lacking. This study synthesises the research work from decades of experiments in order to point researchers in the direction of what was done, the challenges faced, as well as how the models perform. A pool of findings from 108 remote sensing-based AGGB studies published from 1972 to 2020 show that about 62% of the remote sensing-based algorithms were tested in the Steppe grasslands, mostly in the temperate climate zone. An uneven annual publication yield was observed with approximately 36% of the research output from Asia whereas countries in the global south yielded few publications (&lt;10%). Optical sensors, particularly MODIS, remain a major source of satellite data for AGGB studies, whilst studies in the global south rarely use active sensors such as Sentinel-1. Optical data tend to produce poor regression accuracies that are highly inconsistent across the studies compared to Radar. Vegetation indices, particularly the Normalised Difference Vegetation Index (NDVI), remain a major predictor variable. Predictor variables such as Sward height, Red edge position and Backscatter coefficients produced slightly consistent accuracies. Deciding on the optimal algorithm for estimating AGGB is daunting due to the lack of overlap in the grassland type, location, sensor types, and predictor variables, signalling the need for further studies around the transferability of remote sensing-based AGGB models.

COPD is a chronic inflammatory disease characterized by progressive airflow obstruction. Tobacco smoking is the main cause of COPD (COPD-TS), but chronic exposure to biomass smoke (COPD-BS), mainly wood smoke, is the second risk factor; both are considered to cause different phenotypes of COPD. COPD-BS is more eosinophilic than COPD-TS. The objective of the present study was to evaluate the serum level of interleukins involved in eosinophil maturation, recruitment, and survival, and their association with small airway obstruction, measuring cytokines by multiplex test (Bio-Plex) and evaluating the central airway resistance with impulse oscillometry (IOS), comparatively in patients with COPD due to biomass and smoking. The results showed that IL-1ra, IL-2, IL-4, IL-8, IL-9, IL-13, IL-17, and eotaxin were increased in COPD-BS related to COPD-TS. Resistance parameters showed that R5, X5, AX (area reactance), and R5-R20 were significantly higher in COPD-BS than in the COPD-TS group (p < 0.05). R20 was not different between the groups. These data suggest that the cytokines involved in the effect of eosinophils on airway inflammation in COPD-BS were increased compared with COPD-TS, which appears to be related to a predominance of peripheral airway obstruction in patients with COPD-BS more than in COPD-TS

Phenotypic characterization of crop genotypes is an essential yet challenging aspect of crop management and agriculture research. Digital sensing technologies are rapidly advancing plant phenotyping and speeding-up crop breeding outcomes. However, off-the-shelf sensors might not be fully applicable and suitable for agriculture research due to diversity in crop species and specific needs during plant breeding selections. Customized sensing systems with specialized sensor hardware and software architecture provide a powerful and low-cost solution. This study designed and developed a fully integrated Raspberry Pi-based LiDAR sensor named CropBioMass (CBM), enabled by internet of things to provide a complete end-to-end pipeline. The CBM is a low-cost sensor, provides high-throughput seamless data collection in field, small data footprint, injection of data onto the remote server, and automated data processing. Phenotypic traits of crop fresh biomass, dry biomass, and plant height estimated by CBM data had high correlation with ground truth manual measurements in wheat field trial. The CBM is readily applicable for high-throughput plant phenotyping, crop monitoring, and management for precision agricultural applications.

Many corporations and governments aspire to become Net Zero Carbon Dioxide by 2030-2050. Achieving this goal requires understanding where energy is produced and consumed, the magnitude of CO₂ generation, and the Carbon Cycle. Many prior proposed solutions focus on reducing future CO₂ emissions from continued use of fossil fuels. Examination of these technologies exposes their limitations and shows that none offer a complete solution. For example, bioethanol is shown to be both carbon and energy inefficient. Direct Air Capture technologies are needed to reduce CO₂ already in the air. The most natural form of Direct Air Capture involves letting nature do the work of creating biomass via photosynthesis. However, it is necessary to break the Carbon Cycle by permanently sequestering that biomass carbon in “landfills” modified to discourage decomposition to CO₂ and methane. Tree leaves and biomass grown on-purpose, such as high yield switchgrass, are proposed as good biomass sources for this purpose. Left unsequestered, leaves decompose with a short Carbon Cycle time constant releasing CO₂ back to the atmosphere. While in any given year, leaves represent a small fraction of a tree’s above ground biomass, leaves can represent a substantial fraction of the total biomass generated by a tree when integrated over a tree’s lifetime. Understanding the chemistry of the distinct phases landfills undergo is the key to minimizing or eliminating decomposition. First, the compact cross-linked structure of cellulose and keeping water out will make it difficult for initial depolymerization to release sugars. Air ingress should be minimized to minimize Phase I aerobic decomposition. pH manipulation can discourage acid formation during Phase II. Lignocellulose is low in nutrients needed for anaerobic decomposition. Inhibitors can be added if needed. The goal is to move quickly to the dormant phase where decomposition stops. The cost for Carbon Capture and Storage (CCS) for growing and sequestering high yield switchgrass is estimated to be lower than CCS for steam reforming of methane hydrogen plants (SRM) and supercritical or combined cycle coal power plants. Thus, sequestration of biomass is a natural, carbon efficient, and low-cost method of Direct Capture. Biomass sequestration can provide CO₂ removal on giga tonnes per year scale and can be implemented in the needed timeframe (2030-2050).

Tree biomass and diversity relationship in mixed forest impacts on forest ecosystem services provisions. Tree biomass yield is driven by several aspects such as species identity, site condition, stand density, tree age as well as tree diversity expressed as species mingling and structural diversity. By comparing diverse degrees of tree mixture in natural forests we can insight on the ecosystem services provision level and dynamic. Two monitoring sites in the Castilian Northern Plateau (Spain) have been analyzed to disentangle the relationships between biodiversity levels and tree biomass yield. Two permanent one ha squared plots were established at Llano de San Marugan and Valdepoza. In each plot all individual trees were measured (diameter and height), georeferenced and its species identity defined. Tree species in the two sites were Pinus sylvestris, Pinus nigra, Pinus pinea, Quercus pyrenaica, Quercus ilex, Quercus faginea and Juniperus thurifera. From these datasets ten diversity indices that fall in three categories (species richness indices, species compositional/mingling indices and vertical structural indices) were used as predictor variables to fit several candidate models. By merging the trees by site (without considering the species identity) selected models include individual tree basal area as explanatory variable combining by addition or interaction with diversity indices. When species are analyzed independently structural diversity impacts on biomass yield in combination (additive or multiplicative) with tree size is negative Pinus nigra and positive for the other species.

As β-glucosidases represent the major bottleneck for industrial degradation of plant biomass, great efforts are being devoted both to discover novel and robust versions of these enzymes, as well as to develop efficient and inexpensive ways to produce them. In this work, raw glycerol from chemical production of biodiesel was tested as carbon source for the fungus Talaromyces amestolkiae with the aim of producing enzyme cocktails rich in this activity. Approximately 11 U/mL β-glucosidase were detected in these cultures, constituting the major cellulolytic activity. Proteomic analysis revealed BGL-3 as the most abundant protein and the main β-glucosidase. This enzyme crude was successfully used to supplement a basal commercial cellulolytic cocktail (Cellu-clast 1.5L) for saccharification of pretreated wheat straw, corroborating that even hardly exploitable industrial wastes, such as glycerol, can be used as secondary raw materials to produce valuable enzymatic preparations in a framework of circular economy

Biopolymers based on plant and animal proteins are interesting alternatives in the development of films with future prospects as food packaging. Considering that in recent years there has been an increasing interest in the valorization of agro-industrial residues and by-products and that the blending of polymers can lead to materials with improved properties, in this work, keratin-rich feather fibers and gliadins were blended at different ratios in order to develop sustainable and biodegradable films. Control gliadin G100, feather F100 films and their blends at 3:1 (G75F25) , 2:2 (G50F50) and 1:3 (G25F75) ratios were successfully developed through thermoprocessing. The physical properties were differentiated as a function of the concentration of both polymeric matrices. Although gliadins showed higher hydrophilicity confirmed by its highest swelling degree, films with high gliadin ratios exhibited lower water permeability values at low and medium relative humidities. On the other hand, the feathers displayed the highest Young´s modulus values and provided oxygen barrier to the blends, principally at the highest relative humidity. In conclusion, the blend of these protein-based polymers at different ratio resulted on interesting composites whose physical properties could be adjusted.

Worldwide, different strategies are elaborated in order to ensure optimum conditions for the development and growth of the economic competitiveness, but also for increasing the quality of life and environment protection. All these strategies are closely linked with the development and modernization of the systems for producing energy from clean and renewable sources. In this context, the present paper presents the results of the researches regarding the evaluation of the sustainability of the briquettes production, using the biomass resulted from vine winter pruning as raw material. An analysis of the scientific references indicates that nearly 8 Mt of biomass result from over 7.4 million hectares of vine plantations existent worldwide, biomass that could be valorized through densification in order to produce solid biofuels with a lower calorific value of more than 17 MJ·kg-1. When designing the scientific endeavor, the following aspects were considered: defining the aim and objectives of the research; design of the research algorithm; collection, preparation and conditioning of the biomass; chemical analysis of the briquettes; evaluation of the technological characteristics of the briquettes; evaluation of the energy consumption and energy efficiency for producing the briquettes, taking into account two drying methods (natural and artificial drying). In the meantime, some specific laboratory equipment was design and built for the artificial drying of biomass, evaluation of the mechanical durability, measurement of the energy consumption etc. The analysis of the experimental data has led to the conclusion that the agricultural waste from vine pruning can constitute an important and sustainable source of energy in the form of bri-quettes, which fulfill most of the requirements imposed by the international standards.

Adaptations to climate change rely on understanding the dynamics of plant biomass stocks on the planet. The high levels of deforestation in Cerrado have transformed this biome into the second-largest Brazilian source of carbon emissions. The objective of this study was to develop a method to accurately estimate aboveground and total biomass values among shrublands, savannas, and forests located in the Cerrado biome, using an allometric equation adjusted from canopy height, obtained through optical and laser sensors. The results show similarity between the estimates employed by our method and the data found in the literature review for different phytophysiognomies in the Cerrado biome. Shrubland formations showed higher biomass estimation uncertainties due to the discontinuity of isolated trees and the lower canopy height when compared to more clustered tree canopies in savannas and taller canopies in forests. Aboveground biomass estimates were related to expansion factors, and specific maps were developed for each compartment by root, litter, and necromass. The sum of these compartments is presented in the aboveground and below forest biomass map. This study presents, for the first time, the mapping of total biomass in 10 m pixels of all regions of the Cerrado biome.