This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

Fully mechanized mining face production involves complex geological conditions; mining pressure; gas, water, fire and other mining environments. The working face needs a shearer, hydraulic support, a scraper conveyor and other equipment for coordination. The deep integration of intelligent technology with factors such as "humans, machines, the environment, and management" in the workplace is the core content of intelligent coal mines. This paper puts forward an advanced framework for coal mining robot technology systems, including single robots, robotized equipment, robot clusters and unmanned systems. The framework clarifies the common key technologies of coal mining robot research and development and cross-integration with new technologies such as 5G, the industrial internet, big data, artificial intelligence, and digital twins to improve the autonomous and intelligent application of coal mining robots. By establishing a scientific and complete standard system for coal mining robots, we aim to achieve customized research and development and standardized production of various types of robots. A specific analysis was conducted on the research progress of common key technologies such as explosion-proof design, mechanical system innovation, power drive, intelligent sensing, positioning and navigation, and underground communication of coal mining robots. The current research and application status of various types of coal mining robots in China are summarized. A new direction for future coal mine robot research and development is proposed. Moreover, robotic mining systems should be promoted to enhance the overall intelligence level and mining efficiency of mining equipment. To develop human‒machine environment-integrated robots to improve the autonomy and collaboration level of coal mining robots. The digital twinning of the entire mine robot system should be accelerated, the normalized operation level of coal mine robots should be improved, research on coal mining robots, support robots, and transportation robots should be carried out, intelligence should be achieved in fully mechanized mining faces, and equipment support for fewer and unmanned fully mechanized mining faces should be provided. The practical process of implementing coal mining robotization has been summarized, and the technical and engineering feasibility of the coal mining machine population has been verified.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

The invasion of ship domain stands out as a significant factor contributing to the risk of collisions during vessel navigation. However, there is a lack of research on the mechanisms underlying collision risks specifically related to merchant and fishing vessels in coastal waters. This study proposes an assessment method for collision risks between merchant and fishing vessels in coastal waters and validated through a comparative analysis through visualization. First of all, the operational status of fishing vessels is identified. Collaboratively working fishing vessels are treated as a unified entity, expanding their ship domain during operation to assess collision risks. Secondly, to quantify the collision risk between ships, a collision risk index (CRI) is proposed and visualized based on the severity of collision risk. Finally, taking the high risk area of merchant and fishing vessels collision in the Minjiang River Estuary as an example, this paper conduct the analysis involves classifying ship collision scenarios, extracting risk data under different collision scenarios, and visually analyzing areas prone to danger. The results indicate that this method effectively evaluates the severity of collision risk, and the identified high-risk areas resulting from the analysis is verified by accidents occurred in the recent three years.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Toll plaza optimization is essential for improving traffic flow and easing congestion on road networks. This study aims to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer facilitation. Different resources are used for data collection, like the National Highway Authority of Pakistan. Physical data is collected from the established Toll Plaza of Peshawar, along with the development of each line. The goal of this study is to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer happiness. The analysis of present traffic patterns, the detection of bottlenecks, and the creation of plans to ease congestion and enhance overall traffic flow are all part of the optimization process. The approaches used in this study include data analysis, simulation, and traffic modeling. PTV VISSIM is software for transportation planning, design, and analysis. The simulations consider various conditions, such as variable traffic volumes, toll collection methods, and lane configurations. When comparing the different optimization strategies, performance indicators like trip time, latency, and queue length are utilized to determine which approach is practical. Waiting time Vs. Existing each lane, etc, is explained. In the end, comparing queue lengths and throughput across different lane scenarios shows that maximizing throughput with existing lanes yields up to 45% improvement with E-tag lanes, 40% with existing E-tag lanes, 38% with E-tag plus additional toll and cash lanes, 32% with three cash lanes, and 28% with two E-tag lanes. Failure to regularly monitor and adjust the existing lane pattern scenario based on traffic patterns can lead to queues being 20% longer. Without proactive evaluation and optimization, there is a potential 63% opportunity for queue length improvement

A typical orchard's mechanical operation consists of three or four stages: lining, digging for plantation, moving the seedling from nurseries to the farm, moving the seedling to the planting hole, and planting the seedling in the hole. However, the digging the planting hole is the most time-consuming operation. In fruit orchards, robots' usage is increasingly becoming more prevalent to increase operational efficiency. They offer practical and effective services to both industry and people, whether they are assigned to plant trees, reduce the use of chemical fertilizers, or carry heavy loads to relieve staff. Robots can operate for extended periods of time and can highly adept at repetitive tasks like planting many trees. The present study aims to identify the locations for planting trees in orchards using geographic information systems (GIS), to develop an autonomous drilling machine and use the developed robot to open planting holes. There isn't a comparable study on autonomous hole planting in the literature in this regard. The agricultural mobile robot is a four wheeled nonholonomic robot with differential steering and forwarding capability to stable target positions. The designed mobile robot can be used in fully autonomous, partially autonomous, or fully manual modes. The drilling system, which is a y-axis shifter driven by a DC motor with reducer includes an auger with a 2.1 HP gasoline engine. SOLIDWORKS software was used for designing and drawing of the mobile robot and drilling system. The Microsoft Visual Basic.NET programming language was used to create the robot navigation system and drilling mechanism software. The cross-track error (XTE), which determines the distances between the actual and desired holes positions, was utilized to analyze the steering accuracy of the mobile robot to the drilling spots. Consequently, the average of the arithmetic means was determined to be 4.35 cm, and the standard deviation was 1.73 cm. This figure indicates that the suggested system is effective for drilling plant holes in orchards.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

Abstract. This paper proposes a Second Order Terminal Sliding Mode (2TSM) approach to the trajectory tracking of Differential Drive Mobile Robot (DDMR). Within this cascaded control scheme, the 2TSM dynamic controller, at the inner most loop, tracks the robot’s velocity quantities; while a kinematic controller, at the outer most loop, regulates the robot’s positions. In this manner, chattering is greatly attenuated and finite time convergence is guaranteed by the second order TSM manifold which involves higher order derivatives of the state variables, resulting in inherently robust as well as fast and better tracking precision. The simulation results demonstrate the merit of the proposed control methods.

It is unavoidable that the characteristics of the robot system alter inexactly or cannot be correctly determined during movement and are impacted by external disturbances. There are many adaptive control methods, such as sliding control or neural control, to improve the quality of trajectory tracking for robot motion systems. Still, those methods require a large amount of computation related to solving the problem of constrained nonlinear optimization problem. The article presents some techniques for determining an intelligent controller's online learning function parameters, including two circuits: the inner circuit is a state feedback linearized controller, and the outer course is an Interactive learning controller and does not use the robot's mathematical mode with function parameters online optimal learning and intelligent online learning closely following the joint model to stabilize the robot system. Finally, the 2-DOF planar robot simulation is performed on Matlab software R2022b. The findings indicate that outstanding tracking performance is achievable.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

In March 2013, a novel avian influenza A H7N9 virus was emerged in China, which cause rapidly progressive pneumonia and with a high fatality rate. Serologic studies to evaluate neutralizing antibodies of infected patients and birds are invaluable tools for immunogenicity research of H7N9 and epidemiological investigation. Conventional neutralization assays are laborious and time-consuming which also hampered by biosafety requirement. In this study, We construct and produce pseudovirus bearing the full-length hemagglutinin (HA) of H7N9 virus in the Env-defective, luciferase-expressing HIV-1 backbone. The production of lentiviral pseudovirus was analysed by HA gene specific real-time reverse-transcription PCR, transmission electron microscopy (TEM), and Western Blot assay to prove the nucleic acid replication, the morphology of virus, and the expression of HA protein in pseudovirus. After that pseudovirus based inhibition assay was established to detect neutralizing antibodies of a panel of serum samples. Our results demonstrated that H7N9 pseudovirus which had single-cycle infection was generated. By comparing the neutralization antibody titers, pseudovirus based neutralization test could be recognized as an alternative of conventional microneutralization (MN). Hence, we conclude that it is possible to use pseudovirus inhibition assay to screen sera samples, as well as evaluate vaccine-induced neutralizing antibodies against H7N9 virus.

In pattern recognition domain, deep architectures are widely used nowadays and they have achieved fine grades. However, these deep architectures need special demands, especially big datasets and GPU. Aiming to gain better grades without deep networks, we propose a simplified algorithm framework using fusion features extracted from the salient areas of faces. Furthermore, the proposed algorithm has achieved a better result than some deep architectures. For extracting more effective features, this paper firstly defines the salient areas on the faces. This paper normalizes the salient areas of the same location in the faces to the same size, therefore it can gain more similar features from different subjects. LBP and HOG features are extracted from the salient areas, fusion features’ dimensions are reduced by Principal Component Analysis( PCA) and we apply softmax to classify the six basic expressions at once. This paper proposes a salient areas definitude method which uses peak expressions frames to compare with their neutral faces. This paper also proposes and applies the idea of normalizing the salient areas to align the specific areas which express the different expressions. This makes the salient areas found from different subjects have the same size. Besides, gamma correction method is firstly applied on LBP features in our algorithm framework which improves our recognition rates significantly. By applying this algorithm framework, our research has gained state-of-the-art performances on CK+ database and JAFFE database.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

The purpose of this paper is to explore the implementation of Retrieval-Augmented Gen- 14 eration (RAG) technology with open-source Large Language Models (LLMs). For this purpose, a 15 web-based application named PaSSER that integrates RAG with three models - Mistral:7b, 16 Llama2:7b: Orca2:7b, is developed. In its development various technologies are used, including 17 Blockchain for managing and storing assessment results of built-in testing modules. PaSSER em- 18 ploys a set of evaluation metrics for LLMs’ performance - METEOR, ROUGE, BLEU, Perplexity, 19 Cosine similarity, Pearson correlation, and F1 score. The specialized knowledge base is in the smart 20 agriculture domain. As an illustration, the paper presents results and analysis of two tests. First one 21 is assessing the performance of LLMs across different hardware configurations, the other is deter- 22 mining the model that delivers most accurate and contextually relevant responses within the RAG. 23 The paper also discusses the integration of blockchain technology with LLMs to manage and store 24 assessment results within a blockchain environment. The tests revealed that Mistral:7b demon- 25 strates the best results across most of the evaluated metrics. The discussion section comments on 26 technical and hardware considerations that affect the performance of LLMs. Future development 27 will focus in leveraging new larger pre-trained open-source LLMs, exploring different finetuning 28 approaches, and further integration with Blockchain and IPFS.

This paper develops feasible control strategies and associated system responses to bring an autonomous front-axle bicycle robot from specified initial conditions to final conditions such that a specific performance index is minimized. To solve the problem, the following approach is used: The feasible controls derived from the normal equations of optimality are substituted into the state and the costate systems and form a combined control-free state-costate system which is vectorized to enable and ease the application of a numerical method. A computer program written in Matlab computer programming language, codes a fourth-order Runge-Kutta numerical method and then solve the combined state-costate system of ordinary differential equations. The obtained results are the feasible bicycle robot trajectory, the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations are designed and provided to persuade on the effectiveness and the reliability of the approach.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

The B169L protein (pB169L) of African swine fever virus (ASFV) is a structural protein with an unidentified function during the virus replication. The sequences of the B169L gene and the downstream B438L gene are separated by short intergenic regions. However, the regulatory mode of the gene transcription remains unknown. Here, we identified two distinct promoter regions and two transcription start sites (TSS) located upstream of the open reading frame (ORF) of B438L. Using the promoter reporter system, we demonstrated that the cis activity of the ORF proximal promoter exhibited significantly higher levels compared with that of the distal promoter located in the B169L gene. Furthermore, transfection with the plasmids with two different promoters for B438L could initiate the transcription and expression of the B438L gene in HEK293T cells, and the cis activity of the ORF proximal promoter also displayed the higher activities compared with the distal promoter. Interestingly, the B438L distal promoter also initiated the transcription of the alternatively spliced B169L mRNA (B169L mRNA2) encoding a truncated pB169L (tpB169L) (amino acids 92–169), and the gene transcription efficiency was increased upon mutation of the initiation codon located upstream of the alternatively spliced B169L gene. Taken together, we demonstrated that the distal promoter of B438L gene initiates the transcription of both the B438L mRNA and B169L mRNA2. Comprehensive analysis of the transcriptional regulatory mode of the B438L gene is beneficial for the understanding of the association of B438L protein and pB169L and the construction of the gene-deleted ASFV.

The e-commerce sector is in a constant state of growth and evolution, particularly within its subdomain of online food delivery. As such, ensuring customer satisfaction is critical for companies working in this field. One way to achieve this is by providing accurate delivery time estimation. While companies can track couriers via GPS, they often lack real-time data on traffic and road conditions, complicating delivery time predictions. To address this, a range of statistical and machine learning techniques are being employed, including neural networks and specialized expert systems, with different degree of success. One issue with neural networks and machine learning models is their heavy dependence on vast, high quality data. To mitigate this issue we propose two Bayesian generalized linear models to predict time of the delivery. Utilizing a linear combination of predictor variables, we generate practical range of outputs with Hamiltonian Monte Carlo sampling method. These models offer a balance of generality and adaptability, allowing for tuning with expert knowledge. They were compared with PSIS-LOO and WAIC criteria. Results show that both models accurately estimated delivery times from the dataset, while maintaining numerical stability. Model with more predictor variables proved to be more accurate.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimising MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based-control and deep learning techniques, including gated recurrent units (GRU), basic recurrent neural network (RNN) and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimises MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyper-parameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R2 value close to 1, representing a strong correlation between predicted and actual power values.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Meningitis is a severe disease associated with death in children under five with highest rates of infections under age of one. Vaccines for Neisseria meningitides and Haemophilus influenza are used to prevent the main causative agents of meningitis. Administration of H. influenzae type b (Hib) vaccine is recommended at 2, 4 and 6 months with a booster dose at 18 months. N. meningitidis has two commercially available vaccines, the pure polysaccharide is recommended at 24 months meanwhile the protein-conjugated vaccines at 12 months. We sought in this study to examine if coadministering the vaccines for the two main meningitis causing bacteria might be synergistic as a preliminary step towards the possibility of shuffling immunization schedule. So, we coadministered Hib vaccine with commercially available vaccines either quadrate (ACWY) polysaccharide meningococcal (Men) or conjugated meningococcal (Nim) vaccines in Balb/C mice (n = 6/group) and compared to each vaccine administered separately and controls. Thirty-five days post immunization, we measured specific antibodies titers. Hib vaccine increased Men antibody titers significantly for serotypes Y and W. When Hib vaccine was coadministrated with Nim, antibody titer for Y, W and A significantly increased. For serotype C, there was no significant difference in antibody titers among immunized groups. As for effect of meningococcal vaccines on Hib, Men significantly increased Hib antibody titers while Nim had no effect. Collectively, our data suggested that coadministration of Hib and Men or Nim vaccines was safe and had synergistic effect on immune responses elicited to both vaccines. Further studies are needed before immunization schedule modifications. Such immunization schedule recommendation should provide better protection against this life-threatening disease in young children.

Chromatographic separation is a critical technique in the manufacturing processes of both chemical products and biopharmaceuticals. Its principle relies on exploiting the differences in distribution between the stationary and mobile phases to achieve the separation of mixtures. The precision of substance concentration during separation directly impacts the quality and usability of the final product. Therefore, the development of an effective and precise separation control technique has long been a vital concern in the field of chromatographic separation control. Currently, the employment of Simulated Moving Bed (SMB) technology for chromatographic separation, which allows for continuous feed, has been recognized as a cutting-edge technique. SMB is a continuous process technology that enhances the efficiency of adsorbents within the bed. This sequential multi-column SMB technology not only increases production capacity but also reduces the consumption of solvents and water. It is acknowledged as one of the cleanest manufacturing technologies in the biopharmaceutical industry. However, multi-column SMB involves various variables such as flow rates in multiple sections and valve switching times, rendering its system control highly complex. Unlike traditional control objectives that aim to minimize control output errors, the control objective of SMB is to achieve a specific proportion of substance concentration. Consequently, designing and implementing traditional control theories for SMB is challenging, leading to SMB systems largely being controlled based on simple PLC controls. Moreover, these controls are often applicable only to single or a few-column SMB setups, limiting the effectiveness of high-capacity applications. To achieve effective control of SMB, this study employs an adjustable intelligent fuzzy controller with a structure like an approximate neural network (NN) for SMB control research. Simulation results demonstrate that the intelligent controller effectively achieves desirable control outcomes for the SMB system.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

The increasing availability of longitudinal data (repeated numerical observations of same units at different times) requires the development of flexible techniques to automatically detect common errors in such data. Besides obvious and easily identifiable cases, such as missing or out-of-range data, large longitudinal dataset often present problems not easily traceable by the techniques used for generic datasets. In particular, elusive and baffling problems are i) inversion of one or more values from one unit to another; ii) anomalous jumps in the series of values, iii) errors in the timing of the values due to a recalculation operated by the data providers to compensate previous errors. This work proposes a statistical-mathematical approach based on a system of indicators that is able to capture the complexity of the described problems by working at the formal level, regardless of the specific meaning of the data. The proposed approach identifies suspect erroneous data and is applicable in a variety of contexts. We implement this approach in a relevant database of European Higher Education institutions (ETER) by analyzing Total academic staff, that is one of the most important variables, used in empirical analysis as proxy of size and also considered by policy makers at European level.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

The numerical implementation of the controllers allows the use of very complex algorithms with ease. However, in practice, due to its proven advantages, the PID controller (and its variants) is widely used in industrial control systems as well as in many other applications that require continuous control. Most of the methods for tuning the parameters of PID controllers are based on time-invariant linear models of the processes, which in practice can lead to poor performance of the control system. The paper presents an application of reinforcement learning algorithms in tuning of PID controllers for the control of some classes of continuous nonlinear systems. Tuning the parameters of PID controllers is done with the help of Twin Delayed Deep Deterministic Policy Gradients (TD3) algorithm which presents a series of advantages compared to other similar methods from Machine Learning dedicated to continuous state and action spaces. TD3 algorithm is an off-policy Actor-Critic based method and was used as it does not require a system model. The presented technique is applied for control of a biotechnological system which has a strongly nonlinear dynamic. The proposed tuning method is compared to the classical tuning methods of PID controllers. The performance of the tuning method based on the TD3 algorithm is demonstrated through simulation illustrating the effectiveness of the proposed methodology.

This study presents an advanced Simulated Shearer Machine Cutting Experiment System enhanced with digital twin technology. Central to this system is a simulated shearer drum, designed based on similarity theory to mirror the operational dynamics of actual mining cutters accurately. The setup incorporates a modified machining center equipped with sophisticated sensors that monitor various parameters such as cutting states, forces, torque, vibration, temperature and sound. These sensors are crucial for precisely simulating the shearer cutting actions. The integration of digital twin technology is pivotal, featuring a real-time data management layer, a dynamic simulation mechanism model layer, and an application service layer that facilitates virtual experiments and algorithm refinement. This multifaceted approach allows for in-depth analysis of simulated coal cutting, utilizing sensor data to comprehensively evaluate the shearer's performance. The study also includes tests on simulated coal samples. The system effectively conducts experiments and captures cutting condition signals via the sensors. Through time-domain analysis of these signals, gathered while cutting materials of varying strengths, it is determined that the cutting force signal characteristics are particularly distinct. By isolating the cutting force signal as a key feature, the system can effectively distinguish between different cutting modes. This capability provides a robust experimental basis for coal-rock identification research, offering significant insights into the nuances of shearer operation.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

Previous control methods developed by our research team cannot satisfy the high-accuracy requirements of unmanned surface vessel (USV) path-tracking during bathymetric mapping because of the excessive overshoot and slow convergence speed. For this reason, this study developed an adaptive fuzzy integral-derivative line-of-sight (AFIDLOS) guidance law for USV path-tracking control. Integral and derivative terms were added to counteract the effect of the sideslip angle, with which the USV could be quickly guided to converge to the planned path for bathymetric mapping. To obtain a high-accuracy of the look-ahead distance, a fuzzy control method was proposed. The proposed method was verified using simulations and outdoor experiments. The results demonstrate that the AFIDLOS guidance law can reduce the overshoot by 79.85%, shorten the settling time by 55.32% in simulation experiments, and reduce the average cross-track error by 10.91%, and can ensure a 30% overlap of neighboring strips of bathymetric LiDAR outdoor mapping when compared with the traditional method.

In this paper is shown the dynamic modeling and design of a passivity based controller for the RV-3SB robot. Firstly, the dynamic modeling of the of the Mitsubishi Rv-3SB robot is done by the Euler-Lagrange formulation in order to obtain a decoupled dynamic model considering the actuators orientation besides the position of this analyzed robot. It is important to remark that the dynamic model of the RV-3SB robot is done based in the kinematic model obtention in which is developed by the implementation of screw theory. Then the passivity based controller is obtained by separating the end effector variables and the actuator variables by making an appropriate coordinate transformation. The passivity based controller is obtained by selecting an appropriate storage function and by the Lyapunov theory the passivity based control law is obtained in order to drive the error variaable, which is the difference between the measured end effector position variable and the end effector desired position variable. The passivity based controller makes that the error variable reach the origin in finite time taking into consideration the dissipation properties of the proposed controller in order to stabilizes the desired end effector position. A numerical simulation experiement is performed in order to validate the theoretical results obtained in this research study. It is verified by numerical experimentation that the proposed control strategy is efficient and effective in order to drive the error variable to the origin in comparison with other modified techniques found in the literature. Finally, the appropriate discussion and conclusion of this research study are provided.

Imitation Learning is a discipline of Machine Learning primarily concerned with replicating observed behavior of agents known to perform well on a given task, collected in demonstration data sets. In this paper, we set out to introduce a pipeline for collecting demonstrations and training models that can produce motion plans for industrial robots. Object throwing is defined as the motivating use case. Multiple input data modalities are surveyed, and motion capture is selected as the most practicable. Two model architectures operating autoregressively are examined -- feedforward and recurrent neural networks. Trained models execute throws on a real robot successfully, and a battery of quantitative evaluation metrics is proposed, including extrapolated throw accuracy estimates. Recurrent neural networks outperform feedforward ones in most respects, with the best models having an assessed mean throw error on the order of 0.1...0.2 m at distances of 1.5...2.0 m. The data collection, pre-processing, and model training aspects of our proposed approach show promise, but further work is required in developing Cartesian motion planning tools before it is suitable for application in production.

This paper addresses the approach of fully automated intelligent control systems in production organizations, focusing on intelligent production systems research. The overview highlights a gap in control operations ahead of assembly as single-purpose control machines are frequently employed, which is precisely their drawback. Conversely, there are accurate multipurpose measurement centers that do not provide total quality control over the manufactured parts because of the cost and length of the measuring procedure. The study's primary objective was to create an intelligent modular control system, whose concept enables it to control various components. The purpose of the modular intelligent control system is to keep an eye on each module's quality during the pre-assembly phase. This system ensures exact control over the production process of modules by integrating sophisticated sensors, diagnostic tools, and intelligent control mechanisms. The technology makes it possible to monitor several parameters and important quality features. Integrated sensors and diagnostic technologies identify possible inaccuracies and disparities, guaranteeing prompt diagnosis of issues in specific modules. The system's intelligent control algorithms streamline the production process and guarantee synchronization between individual modules to achieve consistent quality and performance. One advantage of implementing the solution is that, on average, inspection time is reduced by 40 to 60% as compared to the prior manual inspection approach. In addition, full measurement data archiving was made available, and finally, the human element—which introduced a substantial error rate into this process—was removed. This system also helps to increase the project's overall efficiency, predictability, and safety while allowing for quick adjustments by standards and requirements.

The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

The scientific community has shown considerable interest in Industry 4.0 due to its capacity to revolutionise the manufacturing sector through digitalisation and data-driven decision-making. However, the actual implementation of Industry 4.0 within complex industrial settings presents obstacles that are typically beyond the scope of mainstream research articles. In this paper, a comprehensive case-study detailing our collaborative partnership with a leading medical device manufacturer is presented. The study traces their evolution from a state of limited digitalisation to the development of a digital intelligence platform that leverages data and machine learning models to enhance operations across a wide range of critical machines and assets. The main business objective was to enhance the energy efficiency of the manufacturing process, thereby improving its sustainability measures while also saving costs. The project encompasses energy modelling and analytics, Fault Detection and Diagnostics (FDD), renewable energy integration and advanced visualisation tools. Together, these components enable informed decision making in the context of energy efficiency.

This study explores fault-tolerant consensus in leader-following heterogeneous multi-agent systems, focusing on actuator failures in uncrewed aerial vehicles (UAVs) and uncrewed ground vehicles (UGVs). An optimization-based fault-tolerant consensus algorithm is proposed. The algorithm utilizes the Euler-Lagrange formula to ensure system consistency under actuator failures, with the Lyapunov stability theory proving the asymptotic stability of the consistency error. The algorithm is applied to heterogeneous multi-agent systems of UAVs and UGVs to derive optimal fault-tolerant consensus control laws for each vehicle type. Simulation experiments give evidence for the feasibility of the proposed control strategy.

Heavy rains have created significant threats to human health and life. Floods and other natural disasters, which have a global impact annually, can be attributed to extended durations of intense precipitation. Accurate rainfall predictions are crucial in nations such as Bangladesh, where agriculture is the predominant occupation. The efficiency of machine learning (ML) methods is enhanced by the non-linearity of rainfall, surpassing the effectiveness of other alternative ways. Machine learning techniques show that individual classifiers exhibit worse accuracy than ensemble learning (EL) methodologies. Ensemble Learning techniques are utilized for rainfall prediction and estimating rainfall quantity and daily average temperature to enhance comprehension of the diverse Machine Learning algorithms. This research implements the machine learning techniques and ensemble-based classifier to predict the rainfall occurrence, along with the machine learning regressor models and ensemble-based regressor for the rainfall amount prediction and daily average temperature prediction, using Bangladesh Weather Dataset. The results of the machine learning and ensemble-based models are compared using the Accuracy and F1 score for rainfall occurrence prediction. In contrast, MAE and RMSE evaluation metrics are used for ensemble regressor and regression algorithms for the rainfall amount and daily average temperature prediction. With an accuracy of 83.41% and a recall of 78.17%, the Ensemble Classifier is the best at predicting when it will rain, but its precision of 51.16% stands in for the lowest. The Ensemble Regression model outperforms Linear Regression, Random Forest, and SVR in rainfall amount prediction, with the lowest MAE of 0.36 and RMSE of 0.90. The Ensemble Regression provides the most precise results for daily average temperature prediction with the lowest MAE 0.42 and RMSE 0.54 highlighting its superiority over the other regression models in forecasting temperature with less error. Ensemble approaches consistently lead task performance metrics.

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

Deadlock is a real problem that can cause expensive, time-dependent hang-ups or failures in distributed computing systems. Some studies have been conducted with deadlock detection and resolution in generalized request computing models, most of these studies are based on the diffusing computation scheme, where forward and backward propagated probe and reply messages respectively are diffused between dependent processes. The replies carry the dependency information between processes for the initiator. Using this dependency information initiator can detect and resolve the deadlock cycle. It has been proven in the literature that a deadlock cycle length distribution is skewed with a large majority of cycles (90%) having length two. Based on this fact an improved algorithm is proposed for handling deadlock detection in distributed computing systems under the distributed request model where each process has several requests at a time. The improved algorithm depends mainly on message propagation and timeout policy. Probe and reply messages are propagated between the initiator and its successors only to detect deadlock cycles between them. Global timeout policy is used to detect potential deadlock cycles with large length distribution. The proposed algorithm can handle concurrent executions. Simulation experiments are performed to see the effectiveness of the improved algorithm. It is found that the improved algorithm compares favorably with other existing algorithms and it shows better results for several performance metrics especially in reducing deadlock latency and execution time.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

In this paper is presented the design and syntheis of a dynamic output feedback neural network controller for a non-holonomic mobile robot. First the dynamic model of a non-holonomic mobile robot is presented, in which these constraints are considered for the mathematical derivation of a feasable representation for this kind of robot. Then two control strategies are provided based on kinematic control for this kind of robot. The first control strategy is based on driftless control, this means, that considering that the velocity vector of the mobile robot is orthogonal to its restriction a dynamic output feedback and neural network controller is designed in order that the control action would be zero only when the velocity of the mobile robot is zero. The Lyapunov stability theorem is implemented in order to find a suitable control law. Then another control strategy is designed for trajectory tracking purposes, which similar to the driftless controller, a kinematic control scheme is provided but suitable to implement in more sophisticated hardware. In both control strategy a dynamic control law is provided along with a feedforward neural network controller, so in this way, by the Lyapunov theory the stability and convergence to the origin of the mobile robot position coordinates is ensured. Finally, two numerical experiment are presented in order to validate the theoretical results synthetized in this research study. Discussions and conclusions are provided in order to analyze the results found in this research study.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

Intelligent transportation systems (ITS) are at the forefront of advancements in transportation, offering enhanced efficiency, safety, and environmental friendliness. To enable ITS, autonomous systems play a pivotal role, leveraging breakthroughs in autonomous driving, data-driven modeling, and multiagent control strategies to establish sustainable and coordinated traffic management. The integration of connected and automated vehicles has garnered significant attention as a potential solution for alleviating traffic congestion and improving fuel economy, achieved through global route optimization and cooperative driving. This study focuses on a predictive control perspective to address the cooperative cruise control problem. Online decision-making is employed during the driving process, utilizing information gathered from the network. By employing bargaining games to establish an operating agreement among vehicles, we formalize a synchronization approach based on predictive control theory. Ultimately, these findings are put to the test in an emulation environment within a hardware-in-the-loop system.

Research on bidirectional human-machine interfaces will enable the smooth interaction with robotic platforms in contexts ranging from industry to tele-medicine and rescue. This paper introduces a bidirectional communication system to achieve multisensory telepresence during the gestural control of an industrial robotic arm. We complement the gesture-based control by means of a tactile-feedback strategy grounding on a spiking artificial neuron model. Force and motion from the robot are converted in neuromorphic haptic stimuli delivered on the user’s hand through a vibro-tactile glove. Untrained personnel participated in an experimental task benchmarking a pick-and-place operation. The robot end-effector was used to sequentially press six buttons, illuminated according to a random sequence, and comparing the tasks executed without and with tactile feedback. The results demonstrated the reliability of the hand tracking strategy developed for controlling the robotic arm, and the effectiveness of a neuronal spiking model for encoding hand displacement and exerted forces in order to promote a fluid embodiment of the haptic interface and control strategy. The main contribution of this paper is in presenting a robotic arm under gesture-based remote control with multisensory telepresence, demonstrating for the first time that a spiking haptic interface can be used to effectively deliver on the skin surface a sequence of stimuli emulating the neural code of the mechanoreceptors beneath.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Starting from the fact that one of the global control strategies of the Permanent Magnet Synchronous Motor (PMSM), namely the Direct Torque Control (DTC) type control strategy, is characterised by the fact that the inner flux and torque control loop usually uses hysteresis ON-OFF type controllers and the oscillations introduced by them have to be cancelled out by the outer speed loop controller (which is usually a PI speed controller and whose performance is good around the global operating points and for relatively small variations of the external parameters and disturbances caused in particular by the load torque variation), while retaining the advantages of the DTC strategy, this paper presents the improvement of the performance of the PMSM sensorless control system using Proportional Integrator (PI), PI Equilibrium Optimizer Algorithm (EOA), Fractional Order (FO) PI, Tilt Integral Derivative (TID) and FO Lead-Lag for constant flux, and Sliding Mode Control (SMC) and FOSMC for variable flux. The performance indicators of the control system are the usual ones: response time, settling time, overshoot, steady-state error and speed ripple, plus another one given by the fractal dimension (FD) of the PMSM rotor speed signal, and the hypothesis that the FD of the controlled signal is higher when the control system provides better performance is verified. The paper also presents the basic equations of the PMSM, based on which the synthesis of integer and fractional controllers, the synthesis of an observer for estimating the PMSM rotor speed, electromagnetic torque and stator flux are presented. The comparison of the performance of the proposed control systems and the demonstration of the parametric robustness are performed by numerical simulations in Matlab/Simulink using Simscape Electrical and Fractional Order Modelling and Control (FOMCON). Real-time control based on an embedded system using a TMS320F28379D controller demonstrates the good performance of the PMSM sensorless control system based on the DTC strategy in a complete hardware-in-the-loop (HIL) implementation.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

Strip steel surface defect recognition research has important research significance in industrial production. Aiming at the problems of defect feature extraction difficulty, slow detection speed and insufficient dataset, YOLOv5 is improved on the basis of YOLOv5, and YOLO-LFPD (Lightweight fine particle detection) model is proposed. By introducing the RepVGG (Re-param VGG) module, the robustness of the model to the surface defect features of strip steel is enhanced, and the expressive ability of the model is improved. FasterNet is used to replace the backbone network, which ensures the accuracy and accelerates the inference speed, making the model more suitable for real-time monitoring. The use of pruning, GA genetic algorithm with OTA loss function method further reduces the model size while better learning the strip steel defect feature information, thus improving the generalisation ability and accuracy of the model. The experimental results show that the introduction of the RepVGG module and the use of FasterNet can well improve the model performance, with a reduction of 48% in the number of parameters, a reduction of 13% in the number of GFLOPs, an inference time of 77% of the original, and an optimal accuracy compared with the network models in recent years. The experimental results on the NEU-DET dataset show that the accuracy of YOLO-LFPD is improved by 3% to 81.2%, which is better than other models, and provides new ideas and references for the lightweight strip steel surface defect detection scenarios and application deployment.

This paper aims at computing feasible control strategies and the corresponding feasible state trajectories to drive an autonomous rear-axle bicycle robot from a given initial state to a final state such that the total running cost is minimized. Pontryagin’s Minimum Principle is applied and derives the optimality conditions from which the feasible control functions, expressed as functions of state and costate variables, are substituted into the combined state-costate system to obtain a new free-control state-costate nonlinear system of ordinary differential equations. A computer program was written in Scilab to solve the combined state-costate system and obtain the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations were provided to show the effectiveness and the reliability of the approach.

This paper aims at computing feasible control strategies and the corresponding feasible state trajectories to drive an autonomous rear-axle bicycle robot from a given initial state to a final state such that the total running cost is minimized. Pontryagin’s Minimum Principle is applied and derives the optimality conditions from which the feasible control functions, expressed as functions of state and costate variables, are substituted into the combined state-costate system to obtain a new free-control state-costate nonlinear system of ordinary differential equations. A computer program was written in Scilab to solve the combined state-costate system and obtain the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations were provided to show the effectiveness and the reliability of the approach.

Gesture recognition has always been a technique to decrease the distance between the physical and the digital world. In this work, we introduce an Arduino based vehicle system which no longer require manual controlling of the cars. The proposed work is achieved by utilizing the Arduino microcontroller, accelerometer, RF sender/receiver, and Bluetooth. Two main contributions are presented in this work. Firstly, we show that the car can be controlled with hand-gestures according to the movement and position of the hand. Secondly, the proposed car system is further extended to be controlled by an android based mobile application having different modes (e.g., touch buttons mode, voice recognition mode). In addition, an automatic obstacle detection system is introduced to improve the safety measurements to avoid any hazards. The proposed systems are designed at lab-scale prototype to experimentally validate the efficiency, accuracy, and affordability of the systems. We remark that the proposed systems can be implemented under real conditions at large-scale in the future that will be useful in automobiles and robotics applications.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

African swine fever virus (ASFV), a highly contagious pathogen characterized by a complex structure and a variety of immunosuppression proteins, causes hemorrhagic, acute, and aggressive infectious disease that severely injure the pork product and industry. However, there is no effective vaccine or treatment. The main reasons are not only the complex mechanisms that lead to immunosuppression, but also the unknown functions of various proteins. This review summarizes the interaction between ASFV and host immune system, along with the involvement of virulence related genes and proteins, as well as the corresponding molecular mechanism of immunosuppression of ASFV, encompassing pathways such as cGAS-STING, NF-κB, JAK/STAT, apoptosis, and other modulation. The aim is to summarize the dynamic process during the ASFV infection and entry into host cell, provide a rational insight into development of vaccine and a better clear knowledge of how ASFV impacts host.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

Deep Learning (DL) oriented document processing is widely used in different fields for extraction, recognition, and classification processes from raw corpora of data. The article examines the application of deep learning approaches, based on different neural network methods, including Gated Recurrent Unit (GRU), Long Short-Term Memory (LSTM), and Convolutional Neural Networks (CNN). The compared models were combined with two different word embedding techniques, namely: Bidirectional Encoder Representations from Transformers BERT and Gensim Word2Vec. The models are designed to evaluate the performance of architectures based on neural network techniques for the classification of CVs of Moroccan engineering students at ENSAK(National School of Applied Sciences of Kenitra, Ibn Tofail University). The used dataset included resumes collected from engineering students at ENSAK in 2023 for a project on the employability of Moroccan engineers in which new approaches were applied, especially machine learning, deep learning, and big data. Accordingly, 867 resumes were collected from five specialties of study (Electrical Engineering, Networks and Systems Telecommunications, Computer Engineering, Automotive Mechatronics Engineering, Industrial Engineering). The results revealed good performance of the proposed models based on the BERT embedding approach compared to models based on the Gensim Word2Vec embedding approach. Accordingly, the CNN-GRU/Bert model achieved slightly better accuracy with 0.9251 compared to other hybrid models.

This paper introduces an alternative method to design the path following controller of an under-actuated spherical mobile robot, which has a single pendulum structure its inside as a driving mechanism. The mechanism has an under-actuated problem; two inputs for the roll and pitch but no direct input for the yaw. In order to overcome this problem, the proposed method defines a virtual reference input for the heading direction. The virtual reference input works as a control input since it can be arbitrarily designed just like the reference input of a conventional system. The control scheme using the defined virtual reference input achieves the stabilization and path following control of the under-actuated spherical mobile robot without any additional control technique. The stability of the proposed control scheme is guaranteed by Lyapunov stability analysis, and simulation results are given to demonstrate its performance.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

Modern building automation systems implement plenty of advanced control and monitoring functions considering various parameters like users’ activity, lighting, temperature changes etc. Moreover, new solutions based on Internet of Things and cloud services are also being developed for smart buildings to ensure comfort of use, user safety, energy efficiency improvements and integration with smart grids and smart city platforms. Such a wide spectrum of technologies and functions requires a new approach in building automation systems design to provide effective way of their implementation and flexibility during operation. At the same time, in the building design and operation industries, tools based on building information modeling and digital twins are being developed. In this paper, the authors discuss development directions and application areas of these solutions, identifying new trends and possibilities of their use in smart homes and buildings. In particular, the focus is on procedures for selecting automation functions, effective integration, and interoperability of building management systems with Internet of Things considering organization of prediction mechanisms and dynamic functional changes in buildings and smart networks. Chosen solutions and functions should consider the requirements from EN ISO 52120 standard and the guidelines defined for the Smart Readiness Indicator.

Bio-molecular reagents like antibodies required in experimental biology are expensive and their effectiveness, among other things, is critical to the success of the experiment. Although such resources are sometimes donated by one investigator to another through personal communication between the two, there is no previous study to our knowledge on the extent of such donations, nor a central platform that directs resource seekers to donors. In this paper, we describe, to our knowledge, a first attempt at building a web-portal titled Bio-Resource Exchange that attempts to bridge this gap between resource seekers and donors in the domain of experimental biology. Users on this portal can request for or donate antibodies, cell-lines and DNA Constructs. This resource could also serve as a crowd-sourced database of resources for experimental biology. Further, in order to index donations outside of our portal, we mined scientific articles to find instances of donations of antibodies and attempted to extract information about these donations at the finest granularity. Specifically, we extracted the name of the donor, his/her affiliation and the name of the antibody for every donation by parsing the acknowledgements sections of articles. To extract annotations at this level, we propose two approaches – a rule based algorithm and a bootstrapped relation learning algorithm. The algorithms extracted donor names, affiliations and antibody names with average accuracies of 57% and 62% respectively. We also created a dataset of 50 expert-annotated acknowledgements sections that will serve as a gold standard dataset to evaluate extraction algorithms in the future. Contact: [email protected], [email protected] Database URL: http://tonks.dbmi.pitt.edu/brx Supplementary information: Supplementary data are available at Database online.

This paper develops a methodology to control the navigation of an autonomous ship robot from an initial state to a final. To solve the problem the following approach is used: The ship robot system is modelled as a control system of six ordinary differential equations involving six state variables and three control variables. After having computed the system Hamiltonian, the feasible controls for optimality are derived from the normal equations of optimality as functions of the state and costate variables. Such controls are substituted into the state and the costate equations and give a combined control-free state-costate system of ordinary differential equations which is solved numerically by using a developed Matlab computer program. Associated computational simulations are designed and provided to show the reliability of the approach.

The presence of anti SARS-CoV2-RBD antibody (Anti-RBD) prevents severe COVID-19. We aimed to determine the accuracy of a point-of-care Anti-RBD test implemented in person living with HIV (PLWH), systemic lupus erythematosus (SLE), and chronic kidney disease (CKD). We enrolled 182 non-comorbid subjects and 335 persons with comorbid (PLWH, SLE, CKD) to test anti-RBD assay compared to surrogate viral neutralization (SVNT) as the reference test. We performed linear correlation analysis between anti-RBD vs SVNT and a ROC analyses to ascertain anti-RBD cut-off at 30%, 60%, and 90% inhibition of SVNT to calculate accuracy. Correlations of anti-RBD to SVNT among all groups were excellent with R= 0.7903, R=0.7843, R=0.8153 among non-comorbid, SLE and CKD groups, respectively, with significantly higher correlation among the PLWH group (R=0.8877; p-value=0.0072) compared to non-comorbid group. The accuracy of the anti-RBD test among PLWH and CKD group was similar with the non-comorbid but showed lower sensitivity in the SLE group (p=0.000014). The specificity of the test remained high in all groups. In conclusion, the Anti-RBD test had excellent correlation to SVNT. The persistently high specificity in all groups suggests that this test can be reliably utilized to detect presence of low neutralization capacity, prompting additional vaccination.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

Accurate and reliable mid-long runoff prediction (MLTRP) is of great importance in water re-sources management. However the MLTRP is not suitable in each basin and how to evaluate the applicability of MLTRP is still a question. Therefore, the total mutual information (TMI) index is developed in this study based on the predictor selection method using mutual information (MI) and partial MI (PMI). The relationship between the TMI and the predictive performance of five models is analyzed by applying five models in 222 forecasting scenarios in Australia. The results over 222 forecasting scenarios demonstrate that, compared with the MI, the developed TMI index can better represent the available information in the predictors, and has more significant negative correlation with the RRMSE with the correlation coefficient between -0.62 and -0.85. This means the model's predictive performance will become better along with the increase of TMI, and there-fore the developed TMI index can be used to evaluate the applicability of MLTRP. When TMI is more than 0.1, the available information in the predictors can support the construction of MLTRP models. In addition, the TMI is used to partly explain the difference of predictive performance among five models. In general, the complex models, which can better utilize the contained infor-mation, are more sensitive to the TMI, and have more significant improvement in terms of predic-tive performance along with the increase of TMI. This research can provide support for the study of MLTRP.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

In an agricultural system, finding suitable watering, pesticide, and soil content to provide the right nutrients for the right plant is a mystery so far. Plants cannot speak and cannot ask which food they require. These problems can be addressed by applying intelligent (fuzzy logic) controllers to IoT devices in order to enhance communication between crops, ground mobile robots, aerial robots, and the entire farm system. The application of fuzzy logic in agriculture is a promising technology that can be used to optimize crop yields and reduce water usage. It was developed based on language and the air properties in the agricultural fields were formulated. The entire system was simulated in the MATLAB/SIMULINK environment with Cisco Packet Tracer integration. The inputs for the system were soil moisture sensors, temperature sensors, humidity sensors, and outputs were pump flow, valve opening, water level, and moisture in sounding. The obtained results were the output of opening valve, moisture in sound, pump flow rate, outflows, water level, and ADH values, which are 10.00000013 rad/sec, 34.72%, 4.494%, 0.025 m^3/sec, 73.31 cm^3, and 750 values respectively. The outflow rate increase indicates that the water is released from the tanks, and the control signal fluctuates, indicating that the valve is opening.

As most of the current dynamic positioning systems are based on model ships, they cannot accu-rately reflect the motion state, position changes, and mutual influence of each part of the dynamic positioning system of actual ships in complex environments. Other actual ships such as cargo ships cannot add various sensors and auxiliary equipment to verify and analyze the positioning system. This article takes the intelligent research and training dual-use ship of Dalian Maritime University, which integrates scientific research and training, as the object of study. This ship will not be affected by the voyage period and route and can choose a suitable sea area for research. Therefore, in order to improve the accuracy and reliability of the dynamic positioning system, research on the ship’s dynamic positioning system was carried out. Firstly, an accurate mathematical model of ship motion was established, and the hydrodynamic derivatives of ship model motion were obtained by nu-merical calculation, and applied to the three-degree-of-freedom model of the intelligent research and training dual-use ship. Then, the model was used as part of the closed-loop simulation model of the ship’s dynamic positioning system, and the terminal sliding mode controller was used for sim-ulation and emulation, thereby obtaining ideal simulation test results. This research helps to im-prove the accuracy and reliability of the dynamic positioning system and provides new ideas and methods for ship motion control.

The paper presents the possibility of using KINECT v2 module to control an industrial robot by means of gestures and voice commands. It describes elements of creating software for off-line and on-line robot control. The application for KINECT module was developed in C# language in Visual Studio environment, while the industrial robot control program was developed in RAPID language in RobotStudio environment. The development of a two-threaded application in RAPID language allowed to separate two independent tasks for the IRB120 robot. The main task of the robot is performed in thread no. 1 (responsible for movement). Simultaneously working thread no. 2 ensures continuous communication with the KINECT system and provides information about the gesture and voice commands in real time without any interference in thread no. 1. The applied solution allows the robot to work in industrial conditions without negative impact of communication task on the time of robot’s work cycles. Thanks to the development of a digital twin of the real robot station, tests of proper application functioning in off-line mode (without using a real robot) were conducted. Obtained results were verified online (on the real test station). Tests of correctness of gesture recognition were carried out, the robot recognized all programmed gestures. Another test carried out was the recognition and execution of voice commands. A difference in the time of task completion between the actual and virtual station was noticed - the average difference was 0.67 s. The last test carried out was to examine the impact of interference on the recognition of voice commands. With a 10dB difference between the command and noise, the recognition of voice commands was equal to 91.43%. The developed computer programs have a modular structure, which enables easy adaptation to process requirements.

The development and utilization of wind energy is of great significance to the sustainable development of China's economy and the realization of the goal of "dual carbon". Under the typhoon system, the randomness and volatility of wind speed become an important basis for affecting the energy efficiency utilization and design of wind turbines. Therefore, based on wind speed and wind direction data at 10m, 30m, 50m and 70m heights of a wind power tower in Yancheng, Jiangsu Province, this paper analyzes the change characteristics of wind speed and wind direction by using BFAST method and Hurst index. Based on typhoon body data, topographic data and mesoscale system wind direction data, the causes of the occurrence and development of wind speed and wind direction of wind tower are further analyzed, and a conclusion is drawn: (1) In BEAST method, there are 5, 5, 6 and 6 change points at the height of 10m, 30m, 50m and 70m respectively. Among them, the change points at the height of 10m, 30m and 50m all change before and after node 325, and the change time point at the height of 70m is inconsistent with other heights. Hurst index results show that the inconsistency at 70m altitude is stronger than that at other altitudes. (2) The wind direction sequence at 10m, 30m, 50m and 70m altitude is fitted by stages, and the direction of wind direction is SE-E-SE-SW-W-NW, where, At the height of 70m, the deviation of the fitting trend line from other altitudes is larger in the wind speed strengthening stage and weakening stage. (3) The wind speed at the height of 10m and 70m has different response degrees to the typhoon body. The correlation between the wind speed and the distance between the wind measurement tower and the typhoon near the center is stronger at the height of 10m than at the height of 70m. The surface type and the wind direction of the mesoscale system also have certain effects on the wind speed and direction. In this paper, the change characteristics and influencing factors of wind speed and direction of wind tower are studied, which provides methods and theoretical support for the study of short-term wind speed when typhoon passes through, and provides reliable support for the selection of wind power forecast indicators and the selection and design of wind turbines under extreme gale weather systems.

The paper introduces a control hybrid model that is designed on the basis of OOSEM (Object-Oriented Systems Engineering Method), MDA (Model-Driven Architecture) concepts, RealTime UML/SysML (Unified Modeling Language/Systems Modeling Language), and an algorithm based on UKF (Unscented Kalman Filter). This hybrid model enables the implementation of control elements for autonomous underwater vehicles (AUVs) and can be adapted to reuse for most standard AUV platforms. To obtain this goal, the dynamic model of AUV is integrated with the following specializations of OOSEM/MDA, in which the analysis model is clarified via the use-case model definition and then combines with HA (hybrid automata) to precisely define the requirements for control. Next, the designed model is specialized via real-time UML/SysML to get the core control blocks, which describe the behaviors and structures of control parts in detail. This design model is then transformed into the model of implementation with the assistance of round-trip engineering to conveniently realize the controller of AUVs. Based on this new model, an AUV controller for low-cost turtle-shaped AUVs is implemented that performs tracking for a planar trajectory with accepted feasibility.

Laser Powder Bed Fusion (L-PBF)-based manufacturing is a growing area of research, with a particular focus on evaluating constraints in printed products. This research emphasises the importance of considering various factors—including mechanical properties and support structures—that influence the final product during the design phase. Specifically, the design of microchannel heat exchangers is highlighted, where all constraints are critical. This article will present a method for analysing channel pressure limitations and report findings about mechanical properties loss from examining tube porosity. This includes a summary of results and the establishment of an experimental device system.

Depth-sensing technology has led to broad applications of inexpensive depth cameras that can capture human motion and scenes in 3D space. Background subtraction algorithms can be improved by fusing color and depth cues, thereby allowing many issues encountered in classical color segmentation to be solved. In this paper, we propose a new fusion method that combines depth and color information for foreground segmentation based on an advanced color-based algorithm. First, a background model and a depth model are developed. Then, based on these models, we propose a new updating strategy that can eliminate ghosting and black shadows almost completely. Extensive experiments have been performed to compare the proposed algorithm with other, conventional RGB-D algorithms. The experimental results suggest that our method extracts foregrounds with higher effectiveness and efficiency.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

Online food delivery services are rapidly growing in popularity, making customer satisfaction critical for company success in a competitive market. Accurate delivery time predictions are key to ensuring high customer satisfaction. While various methods for travel time estimation exist, effective data analysis and processing are often overlooked. This paper addresses this gap by leveraging spatial data analysis and preprocessing techniques to enhance the data quality used in Bayesian models for predicting food delivery times. We utilized the OSRM API to generate routes that accurately reflect real-world conditions. Next, we visualized these routes using various techniques to identify and examine suspicious results. Our analysis of route distribution identified two groups of outliers, leading us to establish an appropriate boundary for maximum route distance to be used in future Bayesian modelling. The spatial analysis revealed that these outliers were primarily deliveries to the outskirts or beyond the city limits. By refining the data quality through these methods, we aim to improve the accuracy of delivery time predictions, ultimately enhancing customer satisfaction.

The IEEE 802.11ah standard is introduced to address the growing scale of Internet of Things (IoT) applications. To reduce contention and enhance energy efficiency within the system, the restricted access window (RAW) mechanism is introduced at the medium access control (MAC) layer to manage the significant number of stations accessing the network. However, the RAW parameters need to be appropriately determined to achieve optimal network performance. In this paper, we optimize the configuration of RAW parameters in the IEEE 802.11ah-based IoT network. We analyze and propose an RAW parameters optimization problem with the objective of improving network throughput and formulate it as a Markov decision process. To cope with the complex and dynamic network conditions, we propose a proximal policy optimization (PPO)-based deep reinforcement learning (DRL) algorithm to find the optimal RAW parameters. We construct network environments with periodic and random traffic in the NS-3 simulator to validate the performance of the proposed PPO-based RAW parameters optimization algorithm. Simulation results reveal that using the PPO-based DRL algorithm, optimal RAW parameters can be obtained under different network conditions, thereby significantly improving network throughput.

The detection, characterization, and monitoring of SARS-CoV-2 recombinant variants is a challenge to public health authorities worldwide. Recombinant variants, composed of two or more SARS-CoV-2 lineages, often have unknown impacts on transmission, immune escape, and virulence in the early stages of emergence. We examined 4,213 SARS-CoV-2 recombinant SARS-CoV-2 genomes collected between 2020 and 2022 from California to describe regional and statewide trends in prevalence. Many of these recombinant genomes, such as those belonging to the XZ lineage, or novel recombinant lineages, likely originated within the state of California. We discuss the challenges and limitations surrounding Pango lineage assignments, the use of publicly available sequence data, and adequate sample sizes for epidemiologic analyses. Although these challenges will continue as SARS-CoV-2 sequencing volumes decrease globally, this study enhances our understanding of SARS-CoV-2 recombinant genomes to date while providing a foundation for future insights into emerging recombinant lineages.

The period of the COVID-19 pandemic resulted in a rapid development of innovative education methods, in particular using e-learning and remote work tools. The effects of this development are also post-pandemic changes in formal teaching regulations, in particular in higher education, allowing classes and lectures to be carried out with Blended Learning or Flipped Classroom methods. This paper provides information about a case study of implementing ICT technologies with elements of the mentioned methods in one of the subjects at a technical university. The implemented tools and solutions in the field of e-learning and interactivity are presented, along with information regarding their perception by students during two academic years in the post-COVID-19 period. The analysis of results of these information and student evaluations indicates their generally positive approach to such innovations in the educational path, and at the same time shows significant challenges for teachers to increase the attractiveness and effectiveness of the teaching process and the development of practical, technical skills of students.

Endoscopy has made a significant and noteworthy contribution to the field of medical science and technology. Nevertheless, its potential remains constrained due to the limited availability of rigid or flexible endoscopes. This paper introduces a novel hydraulic actuator based on electrorheological fluid (ERF) as a pivotal advancement in bridging the existing gap within the realm of endoscopy. Following a comprehensive introduction that briefly outlines the electrorheological effect, the subsequent section is dedicated to the elucidation of the actuator’s development process. Challenges arise, particularly in terms of miniaturization and the realization of a hydraulically sealed system with integrated valve electrodes. An internal electrorheological valve system consisting of four valves that are controlled using a pulse-width modulated high voltage was suitable for position control of the antagonistic hydraulic actuators. High-precision stereolithography (SLA) printing has proven practical for manufacturing the actuator components. For functional testing, a test bench was set up in which the actuator follows a setpoint through a PI control loop. The control deviation ranged from 0.6 to 1 degree, with a response time between 6 and 8 seconds. The experiments have demonstrated that, through the use of ERF and integrated valve electrodes, a miniaturized functional actuator can be constructed.

Selecting road networks in cartographic generalization has consistently posed formidable challenges, driving research towards the application of intelligent models. Despite previous efforts, the accuracy and connectivity preservation in these studies, particularly when dealing with road types of similar sample sizes, still warrant improvement. To address these shortcomings, we introduce a Heterogeneous Graph Attention Network (HAN) for road selection, where feature masking method is initially utilized to assess the significance of road features. Concentrating on the most relevant features, two meta-paths are introduced within the HAN framework: one for aggregating features of the same road type within the first-order neighborhood, emphasizing local connectivity, and another extending this aggregation to the second-order neighborhood, capturing a broader spatial context. For a comprehensive evaluation, we introduce a set of metrics considering both quantitative and qualitative aspects of the road network. Compared to traditional neural networks, our HAN model demonstrates superior accuracy and F1-score, particularly for road types with comparable samples. Additionally, it enhances the overall connectivity of the selected network. In summary, our HAN-based method provides an advanced solution for road network selection, surpassing previous approaches in terms of accuracy and connectivity preservation.

Bearing component damage contributes significantly to rotating machinery failures. It is vital for the rotor-bearing system to be in good condition to ensure proper functioning of the machine. Over recent decades, extensive research has been devoted to the condition monitoring of rotational machinery, with a particular focus on bearing health. This paper provides a comprehensive literature review of recent advancements in intelligent condition monitoring technologies for rolling element bearings. Fundamental monitoring strategies are introduced, covering various sensing, signal processing, and feature extraction techniques for detecting defects in rolling element bearings. While vibration-based monitoring remains prevalent, alternative sensor types are also explored, offering complementary diagnostic capabilities or detecting different defect types compared to accelerometers alone. Signal processing and feature extraction techniques, including time domain, frequency domain, and time-frequency domain analysis, are discussed for their ability to provide diverse perspectives for signal representation, revealing unique insights relevant to condition monitoring. Special attention is given to information fusion methodologies and the application of intelligent algorithms. Multisensor systems, whether homogeneous or heterogeneous, integrated with information fusion techniques, hold promise in enhancing accuracy and reliability by overcoming limitations associated with single sensor monitoring. Furthermore, the adoption of AI techniques, such as machine learning and metaheuristic optimisation, has led to significant advancements in condition monitoring, yielding successful outcomes in various studies. Finally, avenues for further advancements to improve monitoring accuracy and reliability are identified, offering insights into future research directions.

The future of intelligent manufacturing machines involves autonomous selection of process parameters to maximize productivity while maintaining quality within specified constraints. To effectively optimize process parameters, these machines need to adapt to existing uncertainties in the physical system. This paper proposes a novel framework and methodology for feedrate optimization that is based on a physics-informed data-driven digital twin with quantified uncertainty. The servo dynamics are modeled using a digital twin, which incorporates the known uncertainty in the physics-based models and predicts the distribution of contour error using a data-driven model that learns the unknown uncertainty on-the-fly by sensor measurements. Using the quantified uncertainty, the proposed feedrate optimization maximizes productivity while maintaining quality under desired servo error constraints and stringency (i.e., the tolerance for constraint violation under uncertainty) using a model predictive control framework. Experimental results obtained using a 3-axis desktop CNC machine tool and a desktop 3D printer demonstrate significant cycle time reductions of up to 38% and 17% respectively, while staying close to the error tolerances compared to the existing methods.

The technology of left ventricular assist devices (LVADs) requires developing and implementing an intelligent control systems to optimize pump speed to achieve a physiological metabolic demands for heart failure (HF) patients. This work aimed to present an advanced control algorithm to drive an LVAD under different physiological conditions. Pole placement method in conjunction with of sliding mode control approach (PP-SMC) was utilized to design and construct the proposed control method. In this design, the method was adopted to use neural networks to eliminate system uncertainties of disturbances. An elastance function was also developed and used as an input signal to mimic the physiological perfusion of HF patients. Two scenarios ranging from rest to exercise were introduced to evaluate the proposed technique. In this technique, a lumped parameter model of cardiovascular system (CVS) was used for this evaluation. The results demonstrated that the designed controller was robustly tracking the input signal in the presence of the system parameter variations of CVS. In both scenarios, the proposed method shows that the controller automatically drive the LVAD with a minimum flow of 1.7 L/min to prevent suction and 5.7 L/min to prevent over-perfusion.

Oedaleus decorus asiaticus, Calliptamus abbreviatus, Angaracris rhodopa, and Myrmeleotettix palpalis are the main grasshoppers that harm the natural grassland in the Hexi Corridor. In this study, the MaxEnt model was employed to identify the key environmental factors affecting the distribution of the four grasshoppers habitats and to assess their distribution under current and future climate change conditions. The aim was to provide a basis for grasshopper monitoring, prediction, and precise control. In this study, 61 occurrences of O. decorus asiaticus, 68 occurrences of A. rhodopa, 58 occurrences of C. abbreviatus, and 92 occurrences of M. palpalis were recorded by GPS, and the distribution of suitable habitats for O. decorus asiaticus, C. abbreviatus, A. rhodopa, and M. palpalis were predicted under current and future climatic scenarios using a MaxEnt model. The average AUC and TSS values of the four grasshoppers were greater than 0.9, and the simulation results were excellent and highly reliable. The mean annual precipitation was the main factor limiting the current range of suitable areas for these four species. Under the current climate, O. asiaticus, C. abbreviatus, and A. rhodopa were mainly distributed in the central and eastern parts of the Hexi Corridor, and M. palpalis was distributed throughout the Hexi Corridor, with a potential distribution area of 1.44×104, 1.43×104, 1.29×104, and 2.12×104 km2, accounting for 15.3, 15.2, 13.7, and 22.5% of the total area of the grasslands in the Hexi Corridor, respectively. The highly suitable areas of O. asiaticus, C. abbreviatus, and A. rhodopa were mainly distributed in the east-central part of Zhangye City, the western part of Wuwei City, and the western and southern part of Jinchang City, with areas of 0.35×104, 0.29×104, and 0.20×104 km2, accounting for 3.7, 3, and 2.2% of the grassland area, respectively. The high habitat of M. palpalis was mainly distributed in the southeast of Jiuquan City, the west, middle, and east of Zhangye City, the west of Wuwei City, and the west and south of Jinchang City, with an area of 0.32×104 km2, accounting for 3.4% of the grassland area. In the 2030s, the range of O. asiaticus, C. abbreviatus, A. rhodopa, and M. palpalis was predicted to decrease.

According to the requirement of 20kg load of casting barrel, we design a three-dimensional model of the robot and analyze the three stages of liquid level change in the casting barrel during the casting process. Through the analysis, it is determined that the time and angle function is an implicit function, and it is impossible to find the analytical expression of time about angle. The kinetic function of the casting barrel is simulated by MATLAB, and it is found that the function image has mutation points, and when the original function is fitted and approximated by fifth-degree polynomial interpolation, the fifth-degree polynomial function image of the time versus the angular acceleration has a large amplitude of oscillation, especially the mutation points. A PID algorithm based on the discretization of the time and acceleration function is introduced for correction, and the results show that this method effectively reduces the oscillation amplitude of the image and improves the coincidence with the original function.

In recent years, strain sensors have penetrated various fields. The capability of sensors to convert physical signals into electrical signals is of great importance in healthcare. However, it is still challenging to obtain sensors with high sensitivity, large operating range and low cost. In this paper, a stretchable strain sensor made of a double-layer conductive network, including a biomimetic multilayer graphene-Ecoflex (MLG-Ecoflex) substrate and a multilayer graphene-carbon nanotubes (MLG-CNTs) composite up-layer was developed. The combined action of the two layers led to an excellent performance with an operating range of up to 580% as well as a high sensitivity (gauge factor (GFmax) of 1517.94). In addition, a pressure sensor was further designed using the bionic vein-like structure with a multi-layer stacking of MLG-Ecoflex/MLG-CNTs/MLG-Ecoflex to obtain a relatively high deformation along the direction of thickness. The device presented a high sensing performance (up to sensitivity of 0.433 kPa-1), capable of monitoring small movements of the human body such as vocalisations and gestures. The good performance of the sensors together with a simple fabrication procedure (flip-molding) make it potential for some applications, for example, human health monitoring and other areas of human interaction.

In engineering, connections between components are often weak areas. Unreasonable connection methods can easily reduce the strength of components, resulting in unpredictable failure modes. In nature, numerous connection methods for biological structures with excellent mechanical properties have evolved. Studying the connection methods of organisms in nature can inspire new ideas for bionic connection methods. When the diabolical ironclad beetle is under pressure, the elytra are not easy to separate, which ensures the stability of the beetle's external structure, thus making the beetle extremely resistant to pressure. The reason for this is the interlocking and toughening effect of the unique jigsaw connection between the elytra. Therefore, in this paper a theoretical analysis model is established and used to analyze the mechanical behavior of the diabolical ironclad beetle's jigsaw connection during the drawing process and determine the influence of factors such as quantity, angle, and geometric characteristics on the mechanical properties of the jigsaw connection. The results of the theoretical analysis are then compared with the results of experiments and ABAQUS finite element simulation.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

Introduction: Known for its persistent blood-feeding behavior from dawn to dusk, Aedes albopictus is recognized as one of the most dangerous mosquito species due to its role as a vector for diseases such as dengue. Studies have demonstrated that Aedes albopictus thrives in micro-breeding sites predominantly located on private properties, including abandoned containers and manholes used for rainwater and irrigation. This study investigates an innovative methodology, the TombiniNet, to mitigate the proliferation of Aedes albopictus by engaging citizens in the active management of micro-breeding sites on their properties. Materials and Methods: The study was conducted in Alessandria, a city with approximately 100,000 inhabitants, focusing on a sample of 200 houses and a population of about 5,000 people. Researchers conducted a comprehensive survey and analysis of micro-breeding sites for Aedes albopictus on both private and communal properties. The larval control measures were conducted from April to October, aligning with the peak mosquito breeding season. The study's sample included 51% of houses that allowed researchers access, and within these, 81% had Aedes albopictus larvae, often found in diverse water Containers holes of which basically manholes on villa garden floors. For monitoring the adult populations were used ovitraps that were not placed in private homes but in public areas to monitor and control the mosquito population. Results: The study identified that up to 70% of micro-breeding sites for Aedes albopictus in northern Alessandria were located on private properties. Citizen participation was critical to the success of the intervention, with a marked decrease in the number of adult tiger mosquitoes observed in areas where residents actively managed breeding sites using the TombiniNet. The TombiniNet was particularly effective in private areas, as it could be regularly maintained by residents, preventing debris accumulation that could hinder drainage. Discussion: The findings highlight the importance of engaging citizens in mosquito control programs to effectively manage Aedes albopictus populations in urban areas. The TombiniNet intervention demonstrated that a simple, cost-effective solution could significantly reduce mosquito breeding sites on private properties. By addressing both communal and private breeding sites, a comprehensive and sustainable approach to mosquito management can be achieved, thereby reducing the risk of disease transmission. Future studies should focus on long-term monitoring and the development of additional innovative solutions to enhance citizen participation and control measures. The study's success also pointed out the limitations of applying such interventions in public areas where debris could impede the net's effectiveness.

The informational synthesis of neural structures, processes, parameters and characteristics that allow a unified description and modeling as neural machines of natural and artificial neural systems is presented. The general informational parameters as the global quantitative measure of the neural systems computing potential as absolute and relative neural power were proposed. Neural information organizing and processing follows the way in which nature manages neural information by developing functions, functionalities and circuits related to different internal or peripheral components and also to the whole system through a non-deterministic memorization, fragmentation and aggregation of afferent and efferent information, deep neural information processing representing multiple alternations of fragmentation and aggregation stages. The relevant neural characteristics were integrated into a neural machine type model that incorporates unitary also peripheral or interface components as the central ones. The proposed approach allows overcoming the technical constraints in artificial computational implementations of neural information processes and also provides a more relevant description of natural ones.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.