The concept of smart morphing blades, which can control themselves to reduce or eliminate the need for active control systems, is a highly attractive solution in blade technology. In this paper an innovative passive control system based on Shape Memory Alloys (SMAs) is proposed. On the basis of previous thermal and shape characterization of a single morphing blade for a heavy-duty automotive cooling axial fan, this study deals with the numerical analysis of the aerodynamic loads acting on the fan. By coupling CFD and FEM approaches it is possible to analyze the actual blade shape resulting from both the aerodynamic and centrifugal loads. The numerical results indicate that the polymeric blade structure ensures proper resistance and enables shape variation due to the action of the SMA strips.

Modern gas turbines firing temperatures (1500-2000K) are well beyond the maximum allowable blade material temperatures. Continuous safe operation is made possible by cooling the HP turbine first stages -nozzle vanes and rotor blades- with a portion of the compressor discharge air, a practice that induces a penalty on the cycle thermal efficiency. Therefore, a current issue is to investigate the real advantage, technical and economical, of raising maximum temperatures much further beyond current values. In this paper, process simulations of a gas turbine are performed to assess HP turbine first-stage cooling effects on cycle performance. A new simplified and properly streamlined model is proposed for the non-adiabatic expansion of the hot gas mixed with the cooling air within the blade passage, which allows for a comparison of several cycle configurations at different TIT (turbine inlet temperature) and max (total turbine expansion ratio) with a realistically acceptable degree of approximation.. The calculations suggest that, at a given max, the TIT can be increased in order to reach higher cycle efficiency up to a limit imposed by the required amount and temperature of the cooling air. Beyond this limit, no significant gains in thermal efficiency are obtained by adopting higher max and/or increasing the TIT, so that it is convenient in terms of cycle performance to design at lower rather than higher max. The small penalty on cycle efficiency is compensated by lower plant cost. The results of our model agree with those of some previous much more complex and computationally expensive studies, so that the novelty of this paper lies in the original method adopted on which the proposed model is based, and in the fast, accurate and low resource intensity of the corresponding numerical procedure: all advantages that can be crucial for industry needs. The presented analysis is purely thermodynamic, with no investigation on the effects of the different configurations on plant costs, so that future work addressing a thermo-economic analysis of the air-cooled gas turbine power plant is the next logical step.

This paper Numerically investigates the effectiveness of the turbine rotating blade nozzle position on the vortex and film composite cooling performance. The coolant injecting nozzles arranged near the pressure surface side (PS-side-in) .vs. arranged near the suction surface side (SS-side-in) are compared at the rotating speed range of 0-4000rpm with fluid and thermal conjugate approach. Results show that the nozzle position presents different influences under low and higher rotating speed. In terms of the mainstream flow, rotation makes the stagnation line move from the PS-side pressure surface side to the SS-side suc-tion surface side, which changes the coolant film attachment on the blade leading edge surface. The nozzle position however indicates limited influence on the coolant film flow. In terms of the internal channel vortex flow, the coolant injecting from the nozzles forms a high-velocity region near the target wall which brings about enhancing convective heat transfer. The direction of the near wall vortex flow is opposite and align to the Coriolis force direction in both the PS-side-in and SS-side-in, respectively. Therefore, the Coriolis force augments to the heat transfer of the internal vortex cooling in SS-side-in while weakens the internal heat transfer in PS-side-in. Such effects become more intense with higher rotational speed. The blade surface area-averaged dimensionless temperature that inversely proportional to the actual temperature is 7.8% higher in SS-side-in as compared to that in PS-side-in. The SS-side-in suggests more superior composite cooling perfor-mance under the relatively higher rotating speed.

For engines operating with heavy fuel oil (HFO), the nozzle rings of the turbocharger turbines are prone to severe degradation in terms of contamination with unburned fuel deposits. This contamination may lead to increased excitation of blade resonances. A previous study provides technical guidelines on how to extract the relevant information from the pulsation spectra by means of a single probe installed away from the turbine trailing edge and some sound experimental proofs of integral mode turbine vibration detection. These theoretical discussions only allude to the effects of mistuning and interferences due to classical blade passing frequencies on sound radiation patterns emitted by integral blade vibration modes. In this paper, both effects are thoroughly discussed. Combining the knowledge of theoretical study and further experimental results, the application range of this blade vibration detection method can be remarkably extended.

A thorough analysis and comparison of the fatty acid profiles of stipe and blade from Laminaria hyperborea, a kelp species found in the northern Atlantic, is presented. Lipids were extracted and fractionated into neutral lipids, free fatty acids and polar lipids, then derivatized to fatty acid methyl esters prior to GC-MS analysis. A total of 42 fatty acids were identified and quantified, including the n-3 fatty acids α-linolenic acid, stearidonic acid and eicosapentaenoic acid. An n-6/n-3 ratio of 0.8:1 was found in blade and 3.5:1 in stipe, respectively. The ratios vary between the lipid fractions within stipe and blade, with the lowest ratio in the polar lipid fraction of blade. The fatty acid amounts are higher in blade than in stipe, and the highest amounts of n-3 fatty acids are found within the neutral lipid fractions. The amounts of polyunsaturated fatty acids are 3.4 times higher in blade than stipe. This study highlights the compositional differences between the lipid fractions of stipe and blade from L. hyperborea. The amount of polyunsaturated fatty acids, compared to saturated- and monounsaturated fatty acids, as well as the n-6/n-3-ratio, is known to influence human health. In the pharmaceutical, food, and feed industries this can be of importance for production and sale of different health products. Additionally, lipids are today among the unused by products of alginate production, exploiting this material for commercial interest should give both economical and environmental benefits.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

The liquid droplet cooling technique for fast scanning chip calorimetry (FSC) is introduced, increasing the cooling rate for large samples on a given sensor. Reaching higher cooling rates and using a gas as the cooling medium, the common standard for ultra-fast temperature control in cooling, requires reducing the lateral dimensions of the sample and sensor. The maximum cooling rate is limited by the heat capacity of the sample and the heat exchange between the gas and the sample. The enhanced cooling performance of the new liquid droplet cooling technique is demonstrated for both metals and polymers, on examples of solidification of large samples of indium, high-density polyethylene (HDPE), and poly (butylene 2,6-naphthalate) (PBN). It was found that the maximum cooling rate can be increased up to 5 MK/s in room temperature environment, that is, by 2 orders of magnitude, compared to standard gas cooling. Furthermore, modifying the droplet size and using coolants at different temperatures provide options to adjust the cooling rate in the temperature ranges of interest.

In thermal power plants equipped with air-cooled condensers, axial cooling fans operate under the influence of ambient flow fields. Under inlet cross-flow conditions, the resultant asymmetric flow field is known to introduce additional harmonic forces to the fan blades. This effect has previously been studied only numerically or using blade mounted strain gauges. For this study, Laser Scanning Vibrometry was used to assess fan blade vibration under inlet cross-flow conditions in an adapted fan test rig inside a wind tunnel test section. Two co-rotating laser beams scanned a low pressure axial fan, resulting in spectral, phase resolved surface vibration patterns of the fan blades. Two distinct operating points were examined, with and without inlet cross-flow influence. While almost identical fan vibration patterns were found for both reference operating points, overall blade vibration increased by 100% at low fan flow rate due to cross-flow, and by 20% at high fan flow rate. While numerically predicted natural frequency modes could be confirmed from experimental data as minor peaks in the vibration amplitude spectrum, they were not excited significantly by cross-flow. Instead, primarily higher rotation rate harmonics were amplified, i.a. a synchronous blade tip flapping was strongly excited at the blade pass frequency.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

Mathematical models across the applied sciences often utilize a standard methodological representation called a state variable formulation more commonly referred to as state space form. Recent research in unmanned underwater vehicle motor turbine blade thermal modeling for fatigue-life is generalized here permitting the proposed novel state space from to be applied to electrodynamics, motion mechanics, and many other disciplines. Proposed here is a very compact form inherently representing time variance, with a convenient presentation of dynamic variables applicable to all proper transfer functions, where all the distinct, real poles, zeros and gain of the transfer function appear as explicit components in the state space. The resulting manifestation simplifies utilization of the state space methods broadly across the applied sciences.

In a bandsaw machine the blade guides provide additional stiffness and help to align the blade near the cutting region. Typically these are either in form of blocks made of carbide or ceramics or as sealed bearings. Abrasive particles, generated while cutting hard and brittle materials like natural stones, settle between the contact surfaces of the guides and the blade causing wear and premature failure. The hydrostatic guide system as presented in this work, is a contactless blade guiding method that uses force of several pressurized water jets to align the blade to the direction of the cut. For this investigation, cutting tests were performed on a marble block using a galvanic diamond coated bandsaw blade with the upper roller guides replaced by hydrostatic guides. The results show that the hydrostatic guides help to reduce the passive force while cutting to a constant near zero in contrast to the traditional guides. This also resulted in reduced surface roughness of the stone plates that were cut indicating a reduction in lateral vibration of the band. Additionally, it has also been shown that using hydrostatic guides the bandsaw blade can be tilted to counter the bandsaw drift opening opportunities for further research in active alignment control. This original research work has shown that the hydrostatic guide systems are capable of replacing and in fact perform better than state of the art bearing or block guides particularly for stone cutting applications.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

Considering rotation-induced centrifugal stiffening, spin softening, and Coriolis effects, the three-dimensional finite element model of a rotating blade with a dovetail structure is built through the contact dynamics theory. The fixed-interface component mode synthesis method is then adopted to reduce the model for high computational efficiency and adequate model accuracy. The effects of the number of normal modes on the first-six-order modal characteristics of the model varying with the rotating speed are studied between the reduced and full models. Next, the influence of rotating speed and friction factor on the nonlinear dynamic characteristics of the model under the action of aerodynamic force are elaborately discussed. The results show that: (1) tenon-mortise joint contact-induced nonlinearity under low rotating speeds results in the intermittent interference of contact surfaces and frequency multiplications of aerodynamic excitation frequency in the spectrum cascades, while that under high rotating speeds causes the continuous interface contact and asynchronous excitation at the tenon-mortise joint; (2) the increase of friction factor results in a lower contact pressure distribution and the right shift of the resonance peak (i.e., hard nonlinearity).

Complex blade responses such as a rotating stall or simultaneous resonances are common in modern engines and their observation can be a challenge even for state-of-the-art tip-timing systems and trained operators. This paper analyses forced vibrations of axial compressor blades, measured during the bench tests of the SO-3 turbojet. In relation to earlier studies conducted in ITWL with a small number of sensors, a multichannel tip-timing system let us observe simultaneous responses or higher-order modes. To find possible symptoms of a failure, blade responses in a healthy and unhealthy engine configuration with an inlet blocker were studied. The used analysis methods covered all-blade spectrum and the circumferential fitting of blade deflections to the harmonic oscillator model. The proposed modal solver can track the vibration frequency and adjust the engine order on the fly. That way, synchronous and asynchronous vibrations are observed and analysed together with an extended variant of least squares. The proposed approach helps to avoid common mistakes and saves a lot of work related to configuring the conventional solver.

Climate change is expected to influence cooling and heating energy demand of residential buildings and affect overall thermal comfort. Towards this end, the heating degree-day (HDD), the cooling degree-day (CDD) and the HDD+CDD were computed from an ensemble of 7 high-resolution bias-corrected simulations attained from EURO-CORDEX under RCP4.5 and RCP8.5. These three indicators were analyzed for 1971-2000 (from E-OBS) and 2011-2040 and 2041-2070, under both RCPs. Results show that the overall spatial distribution of HDD trends for the 3 time-periods points out an increase of energy demand to heat internal environments in Portugal's northern-eastern regions, most significant under RCP8.5. It is projected an increase of CDD values for both scenarios; however, statistically significant linear trends were only found for 2041-2070 under RCP4.5. The need for cooling is almost negligible for the remaining periods, though linear trend values are still considerably higher for 2041-2070 under RCP8.5. By the end of 2070, higher amplitudes for all indicators are depicted for southern Algarve and Alentejo regions, mainly under RCP8.5. For 2041-2070 the Centre and Alentejo (North and Centre) regions present major positive differences for HDD(CDD) under RCP4.5(RCP8.5), within the 5 NUTS II regions predicting higher heating(cooling) requirements for some locations.

The high environmental impact of conventional methods of cooling and heating has increased the need for renewable energy deployment for covering thermal loads. Towards that direction, the proposed system aims at offering an efficient solar powered alternative, coupling a zeolite-water adsorption chiller with a conventional vapor compression cycle. The system is designed to operate under intermittent heat supply of low-temperature solar thermal energy (<90 °C) provided by evacuated tube collectors. A prototype was developed and tested in cooling mode operation. The results of separate components testing showed that the adsorption chiller was operating efficiently, achieving a maximum coefficient of performance (COP) of 0.65. With respect to the combined performance of the system, evaluated on a typical week of summer in Athens, the maximum reported COP was approximately 0.575, mainly due to the lower driving temperatures at a range of 75 °C. The corresponding mean energy efficiency ratio (EER) obtained was 5.8.

The present studies deliver the computational investigations of a 10 MW turbine with a diameter of 205.8 m developed within the framework of the AVATAR (Advanced Aerodynamic Tools for Large Rotors) project. The simulations were carried out using two methods with different fidelity levels, namely the computational fluid dynamics (CFD) and blade element and momentum (BEM) approaches. For this purpose, a new BEM code namely B-GO was developed employing several correction terms and three different polar and spatial interpolation options. Several flow conditions were considered in the simulations, ranging from the design condition to the off-design condition where massive flow separation takes place, challenging the validity of the BEM approach. An excellent agreement is obtained between the BEM computations and the 3D CFD results for all blade regions, even when massive flow separation occurs on the blade inboard area. The results demonstrate that the selection of the polar data can influence the accuracy of the BEM results significantly, where the 3D polar datasets extracted from the CFD simulations are considered the best. The BEM prediction depends on the interpolation order and the blade segment discretization.

Many research work has demonstrated that taken the Combined Cooling Heating and Power system (CCHP) as the core equipment, the integrated energy system (IES) can bring obvious benefit to energy efficiency, CO2 emission reduction and operation economy in urban areas. Compared with isolated IES, integrated energy micro-grid (IEMG) which is formed by connecting multiple regions IES together, through distribution and thermal network, can further improve the reliability, flexibility, cleanliness and economy of regional energy supply. Based on the existing IES model, this paper describes the basic structure of IEMG and built a IEMG planning model. The planning based on the mixed integer linear programming, and economically construction planning scheme are calculated by using known electricity, heating and cooling loads information and the given multiple equipment selection schemes. At last, the model is validated by a case study. The results show that the application of IEMG can effectively improve the economy of regional energy supply.

The results of the study of the influence of the size of cylindrical samples of A5N aluminum on the time and rate of their cooling are presented. According to experimental data, the temperature dependence of the heat transfer coefficient for pure metals is calculated. It revealed that the process of cooling of the aluminium and its alloys has a relaxation behavior. It has found that the main mechanisms of natural air cooling are convection heat transfer and radiation. The characteristic cooling time due to radiation is less than due to convection. The contribution of thermal radiation is noticeable at high temperatures. It was found that the characteristic times of cooling due to radiation and convection increase with increase in volume to area ratio of the sample.

This study investigates the power production and blade fatigue of a three-turbine array subjected to active yaw control (AYC) in full-wake and partial-wake configurations. A framework of two-way coupled large-eddy simulation (LES) and aeroelastic blade simulation is applied to simulate the atmospheric boundary-layer (ABL) flow through the turbine array and the structural responses of the turbine blades. Mean power outputs and blade fatigue loads are extracted from the simulation results. By exploring the feasible AYC decision space, we find that (a) in the full-wake configuration, the local power-optimal AYC strategy with positive yaw angles endures less flapwise blade fatigue and more edgewise blade fatigue than the global power-optimal strategy; (b) in the partial-wake configuration, applying positive AYC in certain inflow wind directions achieves higher optimal power gains than that in the full-wake scenario and reduces the blade fatigue from the non-yawed benchmark. Through a theoretical analysis based on the blade element momentum theory, we reveal that the aforementioned differences in flapwise blade fatigue between the positively and negatively yawed turbine are due to the differences in the azimuthal distributions of the local relative velocity on blade sections, resulting from the combined effects of vertical wind shear and blade rotation. Furthermore, the difference in the blade force between the positively and negatively yawed front-row turbine induces different wake velocity and turbulence distributions, causing different fatigue loads on the downwind turbine exposed to the wake.

The Virtual Blade Model (VBM) is the implementation of the Blade element model (BEM). This was done by coupling the Blade Element Momentum theory equations to simulate rotor operation with the Reynolds Averaged Navier-Stokes (RANS) equation to simulate rotor wake and the turbulent flow field around it. Exclusion of actual geometry of blades causes lower computational cost (about 10 to 100 times). Also, due to simplifications in the meshing procedure, VBM is easier to set up than the models that consider the actual geometry of blades. One of the main unaddressed limitations of the VBM code was the constraint of modeling up to ten rotor zones within one computational domain. This paper provides a detailed and well-documented general methodology to develop a virtual blade model for simulation of ten-plus turbines within one computational domain to remove the limitation of this widely used and robust code. It is strongly believed that the technical contribution of this paper, combined with the current sky-rocketing advancement of available computational resources and hardware, would open the gates to simulate various engineering problems in the field of aerospace, clean energy, and many more.

The ratio between blade height and chord, named aspect ratio (AR), plays an important role in compressor aerodynamic design. Once selected, it influences stage performance, blade losses, and the stage stability margin. The choice of the design AR involves both aerodynamic and mechanical considerations, and a reasonable aim is frequently to achieve a desired operating range while maximizing efficiency. For a fixed set of aerodynamic and geometric parameters there will be an optimal choice in AR that achieves a maximum efficiency. However, for a state-of-the-art aero-engine design optimality means multi-objective optimality, that is reaching the highest possible efficiency for a number of operating points while achieving a sufficient stability margin. To this end, the influence of the AR on the performance of the first rotor row of a multistage multi-objective high-speed compressor design is analyzed. A careful setup of the high-speed aerodynamic design problem allows the effect of the AR to be isolated. Close to the optimal AR, only a modest efficiency variation is observed, but a considerable change in compressor stability margin (SM) is noted. Decreasing the AR allows for an increasing efficiency, but at the expense of a reduced surge margin. This allows the designer to trade efficiency for stability. Increasing the AR, however, is shown to reduce both surge margin and efficiency, hence a distinct optimality in stability is observed for the analyzed rotor blade row. In this work, the optimality in surge margin with respect to AR is observed whereas a close to optimal efficiency. The predicted range from AR=1.10 to AR=1.64, is only indicative, considering that the definition of a multi-objective optimality requires balancing efficiency and surge margin and that the choice of balancing these two criteria requires making a design choice along a pareto optimal front.

Blade Health Monitoring (BHM) is often necessary in power plants and in aviation to prevent excessive blade vibration and cracks. This article proposes a network of blade tip timing sensors operated in a distributed BHM system. A number of cooperating agents is implemented in smart conditioning units which can autonomously operate in an adverse environment and communicate with other nodes via a serial interface. The project uses special versions of reduced instruction set chips that are able to operate near the hot section of the engine. Due to the limited number of types of microprocessors available in the extended temperature range grading, it was necessary to fully utilize the limited hardware resources and implement preemptive multitasking. For this purpose, a custom operating system and communication protocol were designed. The protocol hosts the middle layer which hides the implementation of the distributed system. The presented architecture ensures the sufficient computational capacity in individual nodes of the network operated in adverse conditions. It is scalable and resistant to transmission errors.

An optimal scheduling strategy for cooling, heating and power (CCHP) joint-power-supply system is proposed to improve energy utilization and minimize costs in this paper. Firstly, the mathematical model of CCHP system is established. Particle swarm optimization (PSO) is used to optimize the regularization coefficient C and the kernel parameter λ which can affect the prediction accuracy of KELM(PSO-KELM). Then PV generation and load prediction model are established by PSO-KELM. In order to jump out of local optimal solution, Cauchy variation is introduced in SFLA local update, and adaptive mutation operation is carried out on SFLA individuals. The predictions of PV generation and load power by PSO-KELM are imported into the objective function, and the microgrid dispatching model is solved by the improved SFLA algorithm. Compared with the traditional GA-KELM and KELM, PSO-KELM has faster convergence and prediction accuracy. Compared with the power supply division, the operation cost of the power grid is reduced by the proposed optimization dispatching strategy of CCHP micro-grid.

With the increasing demand for energy worldwide, researchers from different fields have been striving to improve the sustainability and proper utilization of energy resources. Passive radiative cooling, as a natural energy transport method, can achieve cooling without additional external energy input. This review provides a comprehensive examination of passive radiative cooling, including its fundamental theories and latest development. A particular emphasis is placed on the diverse range of fields where passive radiative cooling has been applied, notably including but not limited to construction and architecture. The current state of applications, potential challenges that may arise with wider adaption and promising research directions for each field are thoroughly discussed. This review underscores the universal applicability and feasibility of passive radiative cooling and contributes to its future development by identifying promising areas for further exploration.

Film cooling technology is of great significance to enhance the performance of aero-engines and extend service life. With the increasing requirements for film cooling efficiency, researchers and engineers have carried out a lot of work on the precision and digital measurement of cooling holes. Based on the above, this paper outlines the importance and principles of film cooling technology, reviews the evolution of cooling holes. Also, this paper details the traditional measurement methods of the cooling hole used in current engineering scenarios with their limitations and categorizes digital measurement methods into five main types, including probing measurement technology, optical measurement technology, infrared imaging technology, computer tomography(CT) scanning technology, and composite measurement technology. The five types of methods and integrated automated measurement platforms are also analyzed. Finally, through a generalize and analysis of cooling hole measurement methods, this paper points out technical challenges and future trends, providing a reference and guidance for forward researches.

Solar energy is a renewable and sustainable source of energy, and it has been used in addition of specified technologies, such as solar cooling. The demand for cooling continues to increase in line with environmental changes and a greater desire for human comfort. This study primarily aimed to analyze the performance of an evaporative cooling system powered by solar energy and assess the economic and environmental impact of this system. In this system, hot, dry incoming air is used to evaporate water, thus transforming part of its sensitive heat into latent heat without any variation in enthalpy or total heat. The outputted air then has a lower temperature and a greater humidity, thus providing a more comfortable, healthier environment for its users. To achieve this study’s objectives, numerical code was developed and implemented in MATLAB. The obtained results reveal that the efficiency of the evaporative cooler exceeds 90%, with maximum efficiency being reached at a high wet-bulb depression, while minimum efficiency was observed when the dry air has a high relative humidity and a low dry-bulb temperature.

Finding the proper entropy functional associated with the inelastic Boltzmann equation for a granular gas is a yet unsolved challenge. The original H-theorem hypotheses do not fit here and the H-functional presents some additional measure problems that are solved by the Kullback–Leibler divergence (KLD) of a reference velocity distribution function from the actual distribution. The right choice of the reference distribution in the KLD is crucial for the latter to qualify or not as a Lyapunov functional, the “homogeneous cooling state” (HCS) distribution of the freely cooling system being a potential candidate. Due to the lack of a formal proof, the aim of this work is to support this conjecture aided by molecular dynamics simulations of inelastic hard disks and spheres in a wide range of values for the coefficient of restitution (α). Our results reject the Maxwellian distribution as a possible reference, whereas reinforce the HCS one. Moreover, the KLD is used to measure the amount of information lost on using the former rather than the latter, and reveals a nonmonotonic dependence with α. Additionally, a Maxwell-demon-like velocity-inversion experiment highlights the microscopic irreversibility of the granular gas dynamics.

This paper presents a comparison of two methods to represent variable blade inertia in two codes for aero-servo-elastic simulations of wind turbines: the nonlinear aeroelastic multi-body model HAWC2 and the nonlinear geometrically exact beam model BeamDyn for OpenFAST. The main goal is to enable these tools to simulate the dynamic behavior of a wind turbine with variable blade inertia. However, in order to simulate the structural response of wind turbines with variable blade inertias, the source code of load simulation tools need to be modified. This is due to the fact that, currently, state-of-the-art load simulation tools for wind turbines are unable to simulate variable rotor blade inertias. The validity of the modified codes is proven based on a simple beam model. The validation shows very good agreement between the modified codes of HAWC2, BeamDyn and an analytical calculation. The add-on of variable blade inertias is applied to reduce the mechanical loads of a 5 megawatt reference wind turbine with an integrated hydraulic-pneumatic flywheel in its rotor blades.

The microstructure evolution of SCM435 cold heading steel at different cooling rates was investigated by means of scanning electron microscopy, TEM, XRD, and electron backscatter diffraction. The results show that the cooling rate has a significant effect on the microstructure of the experimental steel. With an acceleration of the cooling, the microstructure of the steel gradually changed from ferrite and pearlite to ferrite, pearlite, and granular bainite; finally, the pearlite disappeared, and the microstructure changed to acicular ferrite, bainite, and martensite. With an increase in the cooling rate, the morphology of the carbide underwent an evolution from sheet carbide to short-rod carbide, granular carbide, and ultimately thin-strip carbide. With the acceleration of cooling, the proportion of large-angle grain boundaries gradually decreased, and the area of small-angle grain boundaries gradually increased. When the cooling rate was 0.1℃/s, the proportion of large-angle grain boundaries was as high as 52.8%, and the dislocation density was only 1.91 × 1012 cm−2. When the cooling rate was 2.0℃/s, the proportion of large-angle grain boundaries was only 27.1%, and dislocation density increased to 5.38 × 1012 cm−2. With the increase in the cooling rate, the depth of the decarbonization layer and the thickness of the scale oxide gradually decreased, the proportion of FeO phase in the scale phase gradually decreased, and the proportion of Fe3O4 phase and Fe2O3 phase gradually increased. The tensile strength increased monotonously with the increase in cooling rate, whereas the elongation and shrinkage first decreased, then increased, and then decreased. When the cooling rate was 1.0 m/s, the short rod and granular bainite in the material structure endowed the SCM435 steel with excellent strength and toughness matching, and the tensile strength and elongation of the steel reached 895 MPa and 24%, respectively.

In the following work, the assessment of the strength properties of the critical area of the rotor stage of the turbine jet engine was undertaken. This is the place of fixing the blade in the rotor disc. An important aspect of this issue are characteristic geometrical dimensions and operating factors e.g., change in rotor speed. In this paper, the assessment of the strength properties of the existing trapezoidal blade-disc connection was undertaken using parametric analysis considering FSI. Virtual models of the compressor rotor stage were developed, including parametric blade-disc connections and discrete models for FEM and CFD analyses. In the parametric analysis of the blade-disc connection, one-way fluid-structure coupling was used. The parametric analysis was aimed at assessing selected geometric parameters in terms of their impact on the maximum reduced stresses in the blade root. It was examined how the adopted value of the friction coefficient influences the maximum reduced stresses in the rotor stage of the compressor.

The work presents the results of numerical fatigue analysis of a turbine engine compressor blade, taking into account the values of initial stresses resulting from surface treatment - shot-peening. The values of the residual stresses were estimated experimentally using X-ray diffraction. The paper specifies the values of the residual stresses on both sides of the blade and their reduction due to the cutting through the blade - relaxation. The obtained values of the residual stresses were used as initial stresses in the numerical fatigue analysis of the damaged compressor blade, which is subjected to resonant vibrations of known amplitude. Numerical fatigue ε-N life analysis was based on the several fatigue material models: Manson’s, Mitchell’s, Baumel-Seeger’s, Muralidharan-Manson’s, Ong’s, Roessle-Fatemi’s and Median’s, and also on the three models of cyclic hardening: Manson’s, Xianxin’s, and Fatemi’s. Because of this approach, it was possible to determine the relationship between the selection of the fatigue material ε-N model and the cyclic hardening model on the results of the numerical fatigue analysis. Additionally, the calculated results were compared with the results of experimental research, which allowed for a substantive evaluation of the obtained results. These results are of great scientific and practical importance. The problem of determining the fatigue life of blades with defects operating under resonance vibrations is one of the original tasks in the field of fracture mechanics and experimental mechanics. The results obtained are of great importance in the aviation industry and can be used during engine maintenance and inspections to assess the suitability of blades with defects in terms of the needs of further work. This aspect of engineering maintenance is of great importance from the aircraft safety point of view.

This paper analyses the health and performance of 12-stage axial compressor of the TV3-117VM/VMA turboshaft operated in a desert environment. The results of the dimensional control of 4,800 worn blades are analysed to model the wear process. Operational experience and numerical simulations are used to assess the effectiveness of an Inlet Particle Separator. Numerical modal analysis is performed to generate the Campbell diagram of worn blades and identify resonant blade vibration which can lead to high cycle fatigue (HCF). It is shown that the gradual loss of the stall margin over time determines the serviceability limits of compressor blades. Recommendations setting out go / no-go criteria are made to maintenance and repair organisations.

Based on the goals of "high reliability, high frequency, rapid launch, and low cost" for space launch site, and drawing inspiration from the design principles of SpaceX's Starship launch test facility, an integrated dual-sided deflector system for convective cooling and thermal protection is presented. The interaction process between the gas jet and liquid water jet and its effect on the flow field environment are thoroughly studied using numerical calculation methods. Furthermore, Regarding the phase-change heat transfer issue in a compressible gas-liquid two-phase flow and the varying distribution of different bubble shapes and sizes at the gas-liquid interface, a modified Lee model is derived. The rationality and accuracy of the phase-change mass-transfer coefficient values can be improved by adjusting the equivalent diameter and shape factor of the bubbles. The research results demonstrate that compared to the classical Lee model, the modified Lee model can achieve a higher numerical accuracy in predicting the heat and mass transfer processes in gas-liquid two-phase flows. Through comparative analysis with traditional dual-sided deflector and conventional cooling system, the integrated dual-sided deflector system for convective cooling and thermal protection exhibits significant performance advantages in gas flow regulation, flow field environment improvement and erosion protection in the near-ground region of the launch site. Particularly, regarding the thermal environment of the dual-sided deflector, it not only achieves effective flow deflection, but also mitigates the degree of erosion caused by the gas jet on the deflector. This conclusion can provide theoretical references for the thermal protection design of commercial launch vehicle system at space launch site.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.

Bandsaw blades are typical band-shaped cutting tools characterized by a low stiffness and micro-level cutting depth, resulting in distinct wear mechanisms compared to rigid cutting tools. In this study, the evolution of bandsaw tooth wear mechanisms during the bandsawing of Cr12MoV cold-working steel was investigated. The tool life was divided into two stages according to the tooth wear mechanism: a rapid wear stage (Stage I) and a homogeneous wear stage (Stage II). In Stage I, the wear mechanism was dominated by chipping, although multiple wear mechanisms were found because of the relatively poor manufacturing tolerance compared to rigid cutting tools, resulting in remarkable differences between the cutting depths of the individual teeth. In Stage II, abrasive and adhesive wear were the primary wear mechanisms instead of chipping, due to the decreased width and setting magnitude tolerance after Stage I. Furthermore, methods for increasing the bandsaw performance were proposed based on the tooth wear mechanisms.

Many probability-based uncertainty quantification (UQ) schemes require a large amount of sampled data to build credible probability density function (PDF) models for uncertain parameters. Unfortunately, the data collected in compressor blades of aero-engine are mostly limited due to expensive and time-consuming tests. In this paper, we develop a preconditioner-based data-driven polynomial chaos (PDDPC) method that can efficiently deal with uncertainty propagation of limited sampled data. The calculation accuracy of PDDPC method is closely related to the sample size of collected data. Therefore, the influence of sample size on PDDPC method is investigated using a nonlinear test function. Subsequently, we consider the real manufacturing errors of stagger angle for compressor blades. Under three different operating conditions, PDDPC method is applied to investigate the effect of stagger angle error on UQ results of multiple aerodynamic parameters of a two-dimensional compressor blade. The results show that as the sample size of measured data increases, UQ results of aerodynamic performance obtained by PDDPC method gradually converge. There exists a critical sample size that ensures accurate UQ analysis of compressor blades. The probability information contained in the machining error data is analyzed through Kullback-Leibler divergence, and the critical sample size is determined. The research results can make a valuable reference for the fast and cheap UQ analysis of compressor blades in practical engineering.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

The effect of cooling rate on the magnetorheological response was investigated for magnetic hydrogels consisting of carrageenan and carbonyl iron particles with a concentration of 50 wt.%. For magnetic gels prepared by natural cooling, the storage moduli at 0 and 50 mT were 3.7×104 Pa and 5.6×104 Pa, respectively, and the change in the modulus was 1.9×104 Pa. For magnetic gels prepared by rapid cooling, the storage moduli at 0 and 50 mT were 1.2×104 Pa and 1.8×104 Pa, respectively, and the change in the modulus was 6.2×103 Pa, which was 3.1 times higher than that for the magnetic gel of rapid cooling. The critical strains, where G‘=G“ on the strain dependence of the storage modulus, for magnetic gels of natural cooling and rapid cooling were 0.023 and 0.034, respectively, indicating that the magnetic gel of rapid cooling has a hard structure compared to that of natural cooling. Oppositely to this, the change in the storage modulus at 500 mT for the magnetic gel of rapid cooling was 1.6×105 Pa, which was 2.5 times higher than that of natural cooling. SEM images revealed that many small aggregations of carrageenan network were found in the magnetic gel of natural cooling and continuous phases of carrageenan network with large sizes were found in the magnetic gel of rapid cooling. It was revealed that, magnetic particles in the magnetic gel of rapid cooling can move and form a chain structure at high magnetic fields by breaking the restriction from the continuous phases of carrageenan.

Abstract: The paper defines the characteristics of two proto-quark stars (M_b=1.22M_? and M_b=1.62M_(?"\ " )) that were formed after the explosion of the supernova. It is assumed that the changes in the energy and lepton charge of the central regions of the pre-supernova star can be neglected during the implosion. The equation of state for hot quark matter is determined based on the MIT bag theory taking into account the presence of neutrinos. The possible maximum values of the central temperatures of these stars are determined. The energy of neutrinos in the studied proto-quark stars is of the order of 250-300 MeV. The decrease in the mass of these stars during cooling is about 0.16 for M_b=1.22M_? and 0.25 for M_b=1.62M_(?"\ " ).

A ducted photovoltaic façade (DPV) unit Studied using experimental Prototype and simulated in a full scale Computational Fluid Dynamics CFD Model. The Study comes in two parts; This is Part I with the title detailed above and Part II titled ‘A Ducted Photovoltaic Façade Unit with Buoyancy Cooling: Part II CFD Simulation’.. The process adopted in the experimental study is replicated in the simulation Part. The aim was to optimize the duct width behind the solar cells to allow for maximum buoyancy-driven cooling for the cells during operation. Duct widths from 5 to 50 cm were tested in a Proto-type. A duct width of 45 cm had the maximum calculated heat removed from the duct; however, the lowest cell-operating temperature was reported for duct width of 50 cm. It was found that the DT between ducts' inlets and outlets range from 5.47 °C to 12.32 °C for duct widths of 5–50 cm, respectively. The ducted system enhanced module efficiency by 12.69% by reducing PV temperature by 27 °C from 100°C to 73 °C. The maximum calculated heat recovered from the ducted PV system is 422 W. This is 47.98% from the incident radiation in the test. Total summation of heat recovered and power enhanced by the ducted system is 61.67%.

The development and application of marine current energy are attracting more and more attention around the world. Due to the hardness of its working environment, it is important and difficult to study the fault diagnosis of a marine current generation system. In this paper, an underwater image is chosen as the fault-diagnosing signal, after different sensors are compared. This paper proposes a diagnosis method based on the sparse autoencoder (SA) and softmax regression (SR). The SA is used to extract the features and SR is used to classify them. Images are used to monitor whether the blade is attached by benthos and to determine its corresponding degree of attachment. Compared with other methods, the experiment results show that the proposed method can diagnose the blade attachment with higher accuracy.

This work explored and contrasted the effect of microstructure on the tensile properties of AlSi10Mg alloys generated by transient directional solidification depending on variations in cooling rate and Magnesium (Mg) content (i.e., 0.45 and 1wt.% Mg), with a focus on understanding the dendritic growth and phases constitution. Optical and Scanning electron (SEM) microscopies, CALPHAD and thermal analysis were used to describe the microstructure, forming phases and resulting tensile properties. The findings showed that the experimental evolution of the primary dendritic spacing is very similar when both directionally solidified (DS) Al-10wt.% Si-0.45wt.% Mg and Al-10wt.% Si-1wt.% Mg alloys samples are compared. The secondary dendritic spacing was lower for the alloy with more Mg, especially considering the range of high growth velocities. Moreover, a greater fraction of (Al+Si+Mg2Si) ternary eutectic islands surrounding the -Al dendritic matrix was noted for the alloy with 1wt.% Mg. As a result of primary dendritic spacings greater than 180 m related to lower cooling rates, slightly higher tensile properties were attained for the Al-10wt.% Si-0.45wt.% Mg alloy. In contrast, combining dendritic refining (< 150 m) and larger Mg2Si fraction, fast solidified DS Al-10wt.% Si-1wt.% Mg samples exhibited higher tensile strength and elongation. The control of cooling rate and fineness of the dendritic array provided a new insight related to the addition of Mg in slightly higher levels than conventional ones, capable of achieving a better balance of tensile properties in AlSi10Mg alloys.

The study carried out by simulation, concerns the thermal behavior of an office building’s solar fresh air cooling system, based on a LiBr-H₂O absorption chiller in different climatic conditions. The coefficient of performance (COP) and the solar fraction were considered performance parameters and were analyzed with respect to the operating limits: risk of crystallization and maintaining at least a minimum degassing zone. A new correlation between the required solar hot temperature and the cooling water temperature was established and then embedded in another new correlation between the COP and the cooling water temperature that was used in simulations during the whole cooling season corresponding to each location. It was found that: the solar hot water should be maintained in the range of (80-100) °C depending on the cooling water temperature, the COP of the solar LiBr-H₂O absorption chiller with or without cold storage tank can reach (76.5-82.4) % depending on the location, and the solar fraction can reach (29.5-62.0) % without cold storage tank and can exceed 100 % with cold storage tank, the excess cooling power being available to cover other types of cooling loads: through the building envelope, from lighting, from occupants, etc.

The objective of this research is to develop an experimental-theoretical analysis about the influence of the cooling medium and the geometry of the welding bead profile in fatigue life and associated parameters with structural integrity of welded joints. A welded joint with cruciform geometry is considered using SMAW, plates in structural steel ASTM A36 HR of 8 mm of thickness and E6013 electrode input. A three-dimensional computational model of the cruciform joint was created using the finite element method. For this model, the surface undulation of the cord and differentiation in the mechanical properties of the fusion zone were considered, the heat-affected zone (HAZ) and base material, respectively. In addition, an initial residual stress field which was established experimentally was considered. The results were a set of analytical expressions for the weld magnification factor Mk. It was found that values for the latter decrease markedly in function of the intensity of the cooling medium used in the post welding cooling phase, mainly due to the effect of the residual compressive stresses. The obtained models of behavior of the weld magnification factor are compared with the results from other researchers with some small differences, mainly due to the inclusion of the cooling effect of the post weld and the variation of the leg of the weld bead. The obtained analytical equations in the present research for Mk can be used in management models of life and structural integrity for this type of welded joint.

Application of toxic antibacterial agents is considered necessary to control prevalent fresh water microorganisms in evaporative cooling water systems, but these agents can adversely affect the environment and human health. Alternatively, natural antibacterial water chemistry has been applied in industrial cooling water systems for over 10 years with excellent results. The tower water chemistry method concentrates natural salts in highly-softened water to produce elevated pH and dissolved solids, with low calcium and magnesium. This practice conserves water while generating only a small volume of non-toxic natural salt concentrate for cost efficient separation and disposal if required. This review presents a novel perspective of natural antimicrobial chemistry for inhibiting parasitic microbiome functional relationships within the bio-triad of Legionella outbreaks, "Trojan Protozoans" and biofilms. The review further examines practical application and function of polyvalent metal ions in the inhibition of biofilms. Reducing global dependence on toxic antibacterial agents discharged to the environment is an emerging concern due to their impact on the natural microbiome, plants, animals and humans. Discharge of antibacterial agents also contributes to development of pathogen resistance. Use of natural antibacterial chemistry can play a key role in managing the cooling water environment in a more ecologically sustainable manner.

Since the spread of the deadly virus SARS-CoV2 in late 2019, researchers have restlessly been seeking for unraveling how the virus factually enters the host cells. Some proteins on each side of the interaction between the virus and the host cells are involved as the major contributors to this process: 1- the nano-machine Spike protein on behalf of the virus, 2- angiotensin converting enzyme II, the mono-carboxypeptidase and the key component of renin angiotensin system on behalf of the host cell, 3- some host proteases and proteins exploited by SARS-CoV2, In this review, the complex process of SARS-CoV2 entrance into the host cells with the contribution of the involved host proteins as well as the sequential conformational changes in the Spike protein tending to increase the probability of complexification of the latter with angiotensin converting enzyme II, the receptor of the virus on the host cells, are discussed. Besides, the release of the catalytic ectodomain of angiotensin converting enzyme II as its soluble form in the extracellular space and its positive or negative impact on the infectivity of the virus are considered.

It is often difficult to extract data on material and energy wates and related costs in the value chain of conventional production units. Many organizations are not fully aware of the actual cost of material and energy waste. For this purpose, advanced costing methods should be used. This study uses material and energy flow cost accounting to determine material costs, losses, and waste management. The case study of this research is the construction of turbine blades in Iran Power Plant Company. In this study, using the extracted data, the construction costs of turbine blades have been studied. The conventional method of making a turbine blade is the machining method, which we will see has a huge amount of wastes of materials and energy. By studying different methods, we will find that there is an alternative method called forging, which reduces losses and costs. Finally, the costs of the two methods are compared. Engineering economics techniques have also been used to compare two methods on a long-term planning horizon.

Brain tumors are neoplasms with one of the highest mortality rates. Therefore, the availability of methods that allow the quick and effective diagnosis of brain tumors and selection of appropriate treatments is of critical importance for patient outcomes. In this study, coated blade spray-mass spectrometry (CBS-MS), which combines the features of microextraction and fast ionization methods, is applied for the analysis of brain tumors. In this approach, a sword-shaped probe is coated with a sorptive material to enable the extraction of analytes from biological samples. The analytes are then desorbed using only a few microliters of solvent, followed by the insertion of the CBS device into the interface on the mass spectrometer source. The results of this proof-of-concept experiment confirmed that CBS coupled to high-resolution mass spectrometry (HRMS) enables the rapid differentiation of two histologically different lesions: meningiomas and gliomas. Moreover, quantitative CBS-HRMS/MS analysis of carnitine, the endogenous compound, previously identified as discriminating metabolite showed good reproducibility with the variation below 10% when using a standard addition calibration strategy and deuterated internal standards for correction. The resultant data show that the proposed CBS-MS technique can be useful for on-site qualitative and quantitative assessments of brain tumor metabolite profiles.

Multi-board electronic cases with high density and high power modules are widely used in industrial power supply management. With the improvement of case performance and miniaturization requirements, heat dissipation becomes one of the important factors to be considered in the design process. First,The existing small electronic thermal design methods focus on heat dissipation structure or heat source layout optimization,and ignores on-load test for modeling analysis. Second,The selected power module has on-load power consumption, resulting in relatively low calorific value and the effectiveness of thermal design cannot be verified. Third, The thermal lacks Intelligent monitoring and feedback control mechanism. In order to solve these problems, this paper designs a kind of heat dissipation case with intelligent temperature control based on high-power and high-density power supply array. Based on the extremely miniaturization design principle, we adopt the composite heat dissipation mode based on conduction and supplemented by forced air cooling . The case is made of magnesium and aluminum alloy with a perforated design. Finally, we compare and analyze with the existing cooling design. The results show that the case is smaller in volume, and the cooling performance parameters are slightly better than the existing case. Under the condition of high-density and high-power design, The output power of the whole system is not less than 10kw and the lowest packing-level density is not less than 47w/cm2 with high reliability, portability and practicability. It also provides technical support and prototype support for the standardized design of similar power arrays.

The effects of heating rate before solution treatment and cooling rate after solution treatment on the morphological distribution and evolution of precipitation phase of nickel-based single crystal superalloy were studied. The dissolution, precipitation and growth of precipitation phase and matrix phase during heat treatment were analyzed by means of high power scanning electron microscopy. The results show that the morphology of precipitated phase has nothing to do with the distribution of precipitated phase and the heating rate in the heating process, but the cooling rate in the cooling process affects the shape, size and distribution of precipitated phase. The faster the cooling rate, the smaller the precipitated phase is, the more irregular the shape is, the smaller the equivalent edge length is, and the smaller the channel width of matrix phase is.

Temper embrittlement is a major challenge encountered during the heat treatment of high-performance steels for large forgings. This study investigates the microstructural evolution and mechanical properties of Cr-Ni-Mo-V thick-walled steel, designed for new large forgings with a tensile strength of 1500 MPa, under different tempering cooling rates. Optical microscopy (OM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD) were employed to analyze the microstructural features. The results demonstrate that the embrittlement occurring during air cooling after tempering is attributed to the concentration of impurities near Fe3C at the grain boundaries. The low-temperature impact toughness at -40°C after water quenching reaches 29 J due to the accelerated cooling rate during tempering, which slows down the diffusion of impurity elements towards the grain boundaries, resulting in reduced concentration and dislocation density, and increased stability of the grain boundaries, thereby enhancing toughness. the bainite content decreases and the interface between martensite and bainite undergoes changes after water quenching during tempering. These alterations influence the crack propagation direction within the two-phase microstructure, further modifying the toughness. These findings contribute to the understanding of temper embrittlement and provide valuable guidance for optimizing heat treatment processes to enhance the performance of high-performance steels in large forgings.

Due to urban warming, energy demand for cooling buildings is rising. The current study used CitySim to estimate the cooling energy requirements for 40 buildings in Downtown, Dubai using high-resolution climate data from weather research and forecasting (WRF) coupled with single layer urban canopy model (SLUCM). Simulating the four mitigation scenarios allowed for the examination of the reduction in cooling load caused by the addition of greenery at a rate ranging from 25% to 100%. The insulated building's cooling demand reduced by a maximum of 13.89% under 100% GI (M4). Scenario M4 resulted in a reduction of 4.6 kWh/m2 and 3.1 kWh/m2 for the non-insulated and insulated low-rise residential buildings, respectively, while the high-rise buildings saw a reduction of 3.09-4.91 kWh/m2 for the non-insulated and 2.07-3.09 kWh/m2 for insulated buildings. This study offered a potential remedy to deal with the problem of urban heating in subtropical environments.

Air conditioners are indispensable necessities in daily life and industrial production. However, the heat generation of their internal core power components can limit their performance release. In this work, we explore the application of thermoelectric coolers (TECs) in the field of power device heat dissipation through finite element simulation. First, we geometrically modeled the structure and typical operating conditions of core power devices in air conditioners. We compared the temperature fields in air cooling and TEC active cooling modes for high power consumption power devices in a 319 K operating environment. The simulation results show that in the single air cooling mode, the maximum temperature of the 173.8 W power device reaches 394.4 K and the average temperature reaches 373.9 K, which exceeds its rated operating temperature of 368.1 K. However, after adding TEC, the maximum temperature of the power device drops to 331.8 K at an operating current of 7.5 A and the average temperature of the device is 326.5 K. It indicates that TEC active cooling has a significant effect on the temperature control of the power device. At the same time, we also studied the effect of TEC working current on the temperature control effect of power devices. For TEC, there is a minimum working current of 5 A; when it is less than 5 A, TEC has no cooling effect; the cooling effect of TEC increases with an increase in working current. When the TEC working current is 10 A, the average temperature of the power device can be reduced to 292.9 K. This study has made a meaningful exploration of the application of TEC in chip temperature control and heat dissipation, providing a new solution for chip thermal management and accurate temperature control.

The spring-in phenomenon of the composite parts can affect the assembly process. This study aims to predict the spring-in phenomenon of carbon fiber reinforced plastic (CFRP) part. Here, we predict the spring-in of the CFRP part using a coupled analysis of the forming and cooling processes during the stamping process. First, a simulation of the entire forming process, such as the transfer of the composite laminate, gravity analysis, and forming was performed to obtain the temperature distribution of the CFRP part. Subsequently, a finite-element (FE) simulation of the cooling process was conducted to predict the spring-in phenomenon of the shaped CFRP part using the temperature data obtained in the forming simulation. Finally, a CFRP part was manufactured and compared with the results of the FE simulation.

To study the heat and mass transfer characteristics of an evaporative cooler for cooling high-temperature working fluids such as supercritical carbon dioxide, an experimental device of the evaporative cooler was built, and a corresponding test system was constructed. Then, the experimental study was carried out based on the orthogonal test method, and the law and extent of the influence of water flow in the tube, spray water flow rate, inlet water temperature in the tube, and air flow rate on heat dissipation, cooling efficiency, and heat and mass transfer coefficients have been obtained. The correlation equations of the heat and mass transfer coefficients were obtained by fitting the orthogonal experimental data, and the validity of the correlation equations was confirmed by the verification experiment.

The basic oxygen furnace slag (BOF) was wide used in road construction, but there was a lack of characteristics in different asphalt mixtures. This study investigates the properties of hot-mixed asphalt (HMA) containing stone mastic asphalt (SMA), porous asphalt (PA) and dense-graded BOF as a partial substitution for natural aggregates. The purpose of this study is to evaluate various BOF slag contents in the asphalt mixtures would affect the cooling behavior after compaction. Asphalt mixture specimens contained 0%, 20%, 40% and 60% BOF slag, respectively, as coarse aggregate. Test results showed that BOF slag has a lipophilic property, so it can be adsorbed by asphalt cement, thereby reducing the cost of asphalt. The stability value of all asphalt mixtures increases with the proportion of BOF slag replacement. In addition, the voids in the mineral aggregate (VMA) value variable exhibited significant differences among asphalt mixtures, and could determine the deviation of the cooling trend of asphalt mixtures. Furthermore; it was found that the cooling procedure of the BOF slag used in dense-graded asphalt mixture takes about 100 min, and that the temperature tends to be moderate; however, it took about 120 min of cooling the SMA and PA mixture with BOF slag. In addition, the voids distribution of dense asphalt mixture was not uniform. It would result in various locations of thermal energy temperature on asphalt mixtures that were inconsistent.

Monitoring the integrity of aeronautical structures is fundamental for safety. Structural Health Monitoring Systems (SHMS) perform real-time monitoring functions, but their performances must be carefully assessed. In this work the damage detection performances of a strain-based SHMS, were evaluated on a composite helicopter rotor blade root. The SHMS monitored the bonding between the central core and the surrounding antitorsional layer. A damage detection algorithm was trained through Finite Element analyses performed on the component. The effects of the loads variability and of damages were decoupled by including a load recognition step in the algorithm. Load recognition was accomplished in different ways: version#1 adopted an Artificial Neural Network (ANN) trained on blades in pristine condition; version#2 was trained also on damaged blades; version#3 adopted a calibration matrix method. Anomaly detection, damage assessment, and localization were performed by using an ANN. Results showed a higher load identification and anomaly detection accuracy for version#1 and version#2 compared to version#3. Gaussian noise reduced anomaly detection and damage assessment performances, and reduced damage localization accuracy for bigger damages. The damage detection performance were obtained for a fibre optic based-SHMS, including the trade-off between probability of detection and false alarm rate for different damage sizes.

Securing the structural safety of blades has become crucial, owing to the increasing size and weight of blades resulting from the recent development of large wind turbines. Composites are primarily used for blade manufacturing because of their high specific strength and specific stiff-ness. However, in composite blades, joints may experience fractures from the loads generated during wind turbine operation, leading to deformation caused by changes in the structural stiff-ness. In this study, 7,132 debonding damage data, classified by damage type, position, and size, are selected to predict debonding damage based on natural frequency. The change in the natural frequency caused by debonding damage is acquired through finite element (FE) modeling and modal analysis. Synchronization between the FE analysis model and manufactured blades is achieved through modal testing and data analysis. Finally, the relationship between the debond-ing damage and the change in natural frequency is examined using artificial neural network techniques

Numerical simulations of turbulent flows in a stirred dead-end membrane bioreactor are performed by the RNG k-ε model based on finite volume method using Fluent codes. Comparisons of numerical and experimental results confirm the reliability and feasibility of the constructed model. Flow structures such as wake flows and circulation loops in stirred flows were well simulated. An increase of stirring speed is proposed to use to minimize the low velocity region. The single vane stirrer is found to be beneficial for biological separations. Results reveal that the increase of vane number can enhance the mixing effect in flow domains. However, a circular disk stirrer goes against the formation of vertical circulations. The six-vane stirrer is found to be able to provide a uniform distribution of high shear stress.

Purpose – Extend the Blade Element Momentum Theory (BEMT) such that rotors with pronounced cone and axis angle (tilt or yaw) can be calculated. Derive an equation for the speed ratio (lambda) as a function of Tip Speed Ratio (TSR), radius, blade, cone and axis angle. This converts the BEMT into an Unsteady BEMT or UBEMT. Present the Wagner rotor as one such rotor geometry. --- Methodology – Literature review and calculations. --- Findings – The UBEMT can be used to calculate highly unconventional rotor geometries. --- Research Limitations – Although the aerodynamic coefficients used in the UBEMT are from measurements in steady flow conditions, they can be used with success. --- Practical Implications – Also conventional Horizontal Axis Wind Turbines (HAWT) with noticeable cone and axis angle should be calculated with the UBEMT. The accuracy of power calculations of these HAWTs can be slightly improved. --- Originality – Analytic equations for rotors with cone and axis angle have barely been discussed.

Knowledge about laminar-turbulent transition on operating multi-megawatt wind turbine blades needs sophisticated equipment like hot-films or microphone arrays. Contrarily thermographic pictures can easily be taken from the ground and temperature differences indicate different states of the boundary layer. The accuracy however, still is an open question, so that an aerodynamic glove known from experimental research on aero-planes was used to classify the boundary-layer state of a 2 megawatt wind turbine blade operating in the orthern part of Schleswig-Holstein, Germany. State-of-the-art equipment for measurering static surface pressure was used for monitoring the lift distribution. To distinguish laminar and turbulent parts of the boundary layer (suction side only) 48 microphones were applied together with ground-based thermographic cameras from two teams. Additionally, an optical camera mounted on the hub was used to survey vibrations. During start-up (from 0 to 9 rpm) extended, but irregularly shaped regions of a laminar boundary layer were observed which had the same extension measured both with microphones and Thermography. When an approximately constant rotor rotation (9 rpm corresponding to approximately 6 m/s wind-speed) was achieved, a flow transition was visible at the expected position of 40 % chord length on the rotor blade, which was fouled with dense turbulent wedges and an almost complete turbulent state on the glove was detected. In all observations, quantitative determination of the flow transition positions from thermography and microphones agree well within their accuracy.

The effects of the coolant pulsation and the film cooling with the plasma aerodynamic actuation (PAA) could be herein explored via large eddy simulations. The electrohydrodynamic force derived from the PAA was solved through the phenomenological plasma model. The Strouhal number of the sinusoidal coolant pulsation and the averaged pulsation blowing ratio were 0.25 and 1.0, respectively. Comprehensive analyses were carried out on the time-averaged flow fields, and the results revealed that the pulsed cooling jet might cause a deeper penetration into the crossflow, and this phenomenon could be remarkably mitigated by the downward force of the PAA. Furthermore, because of the coolant pulsation, the counter rotating vortex pair (CRVP) expanded to lifted off the wall less well, and the PAA lessened the negative lift-off impact and entrapment from the CRVP. Then, the spatial-temporal development of the coherent structures was figured out by the alterations of the centerline temperature, reflecting formation of the intermittent coherent structures rather than hairpin vortices due to the coolant pulsation, and their size and upcast behaviors were reduced by the PAA. Consequently, there was a basic suppression of the turbulent mixing of the cooling fluid with the crossflow. Finally, the three-dimensional streamlines confirmed that the coherent structure dynamic behaviors were significantly regulated by the PAA for alleviating the adverse influences of the coolant pulsation. In summary, through controlling how the dominating coherent structures evolve throughout time and space, the PAA can effectively increase the pulsed film cooling efficiency.

We propose a method of cooling nuclear spin systems of solid-state nanostructures by application of a time-dependent magnetic field synchronized with spin fluctuations. Optical spin noise spectroscopy is considered as the method of fluctuation control. Depending on the mutual orientation of the oscillating magnetic field and the probe light beam, cooling might be either provided by dynamic spin polarization in an external static field or result from population transfer between spin levels without build-up of a net magnetic moment (“true cooling”).

This empirical study investigates large urban park cooling effects on the thermal comfort of occupants in the vicinity of the main central park, located in Madrid, Spain. Data were gathered during hot summer days, using mobile observations and a questionnaire. The results showed that the cooling effect of this urban park of 140 ha area at a distance of 150 m is able to reduce temperature by an average of 0.63°C and 1.28°C for distances of 380 m and of 665 meters from the park. Moreover, the degree of the Physiological Equivalent Temperature (PET) index at a distance of 150 meters from the park is on average 2°C PET and 2.3°C PET less compared to distances of 380 m and 665 m, respectively. Considering distance from the park, the correlation between occupant Perceived Thermal Comfort (PTC) and PET is inverse. That is, augmenting the distance from park increases PET, while the extent of PTC reduces accordingly. The correlation between these two factors at the nearest and furthest distances from the park is meaningful (P-value <0/05). The results also showed that large-scale urban parks generally play a significant part in creating a cognitive state of high-perceived thermal comfort spaces for residents.

The microstructure and solidification behavior of nickel based GTD222 superalloy at different cooling rates are studied. The solidification of the GTD222 superalloy proceeds as follows: L→L+γ, L→L+γ+MC, L→L+(γ/γ ′)-Eutectic and L→η phase. The temperature of liquidus of GTD222 superalloy is 1360 °C while the solidus is slightly lower at 1310 °C, which due to the alloying elements redistribution. It was found that the dendrite arm spacing of the alloy decreased with the increase of cooling rate (From 200 μm at 2.5 K/min to 100 μm at 20 K/min).

The United Arab Emirates (UAE) is significantly dependent on desalinated water and groundwater resource, which is expensive and highly energy intensive. Despite the scarce water resource, only 54% of the recycled water was reused in 2015. In this study, an “Oasis” complex comprised of Sustainable Farming Compartments (SFCs) was proposed for reusing treated wastewater to decrease the ambient temperature of the SFC via an evaporative cooling system. A prototype SFC with half the original scale (width = 1.8 m, depth = 1.5 m, front height = 1.2 m back height = 0.9 m) was designed, built, and tested in an environmentally controlled laboratory and field site to evaluate the feasibility and effectiveness of the SFC under the climatic conditions in Abu Dhabi. Based on the experimental results, the temperature drops obtained from the SFC in the laboratory and field site were 5 ̊C at initial relative humidity of 60% and 7- 15 ̊C at initial relative humidity of 50%, respectively. An energy simulation using dynamic numerical simulations was performed in comparison to the results of the experiment. The energy-based dynamic simulation shows good agreement with the experimental results. The total power consumption of the SFC system was approximately three and a half times lower than that of an electrical air conditioner.

In this work, we focus on investigating electrothermal flow in a rotating electric field (ROT-ETF), with primary attention paid to the horizontal traveling-wave electrothermal (TWET) vortex induced at the center of the electric field. The frequency-dependent flow profiles in the microdevice are analyzed using different heat transfer models. Accordingly, we address in particular the importance of electrode cooling in ROT-ETF as metal electrodes of high thermal conductivity while substrate material of low heat dissipation capability are employed to develop such microfluidic chips. Under this circumstance, cooling of electrode array due to external natural convection on millimeter-scale electrode pads for external wire connection occurs and makes the internal temperature maxima shift from the electrode plane to a bit of distance right above the cross-shaped interelectrode gaps, giving rise to reversal of flow rotation from a typical repulsion-type to attraction-type induction vortex, which is in good accordance with our experimental observations of co-field TWET streaming at frequencies on the order of reciprocal charge relaxation time of the bulk fluid. These results point out a way to make a correct interpretation of out-of-phase electrothermal streaming behavior, which holds great potential for handing high-conductivity analytes in modern microfluidic systems.

In the theoretical treatment of crystallization it is commonly assumed that relaxation processes of the liquid proceed fast as compared to crystal nucleation and growth processes. Actually, it is supposed that the liquid is located always in the metastable state corresponding to the current values of pressure and temperature. However, near and below the glass transition temperature, Tg, this condition is commonly not fulfilled. In such cases, in the treatment of crystallization, deviations of the state of the liquid from the respective metastable equilibrium state have to be accounted for in determining the kinetic coefficients governing the crystallization kinetics, the thermodynamic driving force of crystallization, and the surface tension of the aggregates of the newly evolving crystal phase including the surface tension of critical clusters affecting considerably the crystal nucleation rate. These factors may considerably influence the course of the overall crystallization process. A theoretical analysis of the resulting effects is given in the present paper by numerical solutions of the J(ohnson)–M(ehl)–A(vrami)–K(olmogorov)–equation employed as the tool to model the overall crystallization kinetics and by analytical estimates of the crystallization peak temperatures in dependence on cooling and heating rates. The results are shown to be in good agreement with experimental data. Possible extensions of the theory to be explored in future analysis are anticipated.

Non-tuberculous mycobacteria (NTM) are opportunistic pathogens that cause illness primarily in the elderly, in the immunocompromised or in patients with underlying lung disease. Mycobacterium chimaera is a NTM species belonging to the M. avium Complex (MAC) group of species. Since 2013, a global outbreak of M. chimaera infection related to heater-cooler units (HCU) used in cardio-thoracic surgery has been identified. This outbreak was caused by a single strain of M. chimaera. In order to estimate the prevalence of this outbreak strain in Israel, we sampled M. chimaera from several HCU machines in Israel, as well as from patients, sequenced their genomes and compared them to the outbreak strain. The presence of mixed mycobacteria species in the samples complicated the analysis of obtained sequences. By applying a metagenomic binning strategy, we were able to obtain genomes of single strains from the mixed samples, and characterized them. M. chimaera strains were compared to each other and to previously reported genomes from other countries. The strain causing the outbreak related to the HCU machines was identified in several such machines in Israel but not in any of the clinical samples.

To achieve the required mechanical properties in the heat treatment of steel, it is necessary to have an adequate cooling rate and to achieve the desired final temperature of the product. This should be achieved with one cooling unit for different product sizes. In order to provide high variability of the cooling system, different types of nozzles are used in modern cooling systems. Designers often use simplified, inaccurate correlations to predict the heat transfer coefficient, resulting in oversizing of the designed cooling or failure to provide the required cooling regime. This typically results in longer commissioning times and higher manufacturing costs of the new cooling system. Accurate information about the required cooling regime and the heat transfer coefficient of the designed cooling is critical. This paper presents a design approach based on laboratory measurements. Firstly, the way to find or validate the required cooling regime is presented. The paper then focuses on nozzle selection and presents laboratory measurements that provide accurate heat transfer coefficients as a function of position and surface temperature for different cooling configurations. Numerical simulations using the measured heat transfer coefficients allow the optimum design to be found for different product sizes.

Understanding the thermal cracks of rock caused by high temperature is of great help to the development of underground engineering, such as geothermal mining, underground coal gasification. Although there has been many study on thermal cracking, it is not systematic and in-depth enough. In order to deeply study the thermal crack mechanism of rock, this paper conducted thermal cracking experiments on granite at different temperatures and heating/cooling paths, and qualitative and quantitative analysis was conducted on the crack initiation characteristics, propagation paths, and crack network morphology of rock thermal crack under different test conditions. The thermal crack mechanism was also analyzed from the perspectives of mineral petrology, fracture mechanics, thermodynamics, and other aspects. The research results show that there are two obvious mutation points in the study temperature range for samples with fast cooling paths (SF path: slow heating and fast cooling; FF path: fast heating and fast cooling), around 200-300 ℃ and 600 ℃, respectively, while for samples with slow cooling paths (SS path: slow heating and slow cooling; FS path: fast heating and slow cooling), there is only one mutation point around 600 ℃. The initiation positions of thermal cracking under all temperature paths are relatively similar, with intergranular crack located between particles at the edge of the sample or intercrystalline crack in the middle of feldspar or quartz aggregates. The initiation temperature of SF and FF path specimens is relatively low compared to SS and FS path specimens, and the number and size of cracks is small. The crack network structure formed by the SF path is the most complex, with the largest crack ratio and cumulative crack length; The crack network structure formed by the FF path is relatively complex, with a larger main crack size but relatively fewer secondary cracks; The FS and SS paths do not form a complex network with good connectivity. The process of thermal crack development can be divided into three stages: the development of small cracks, the joint development of main cracks and small cracks, and the connection of cracks into a network structure. The mechanism of thermal crack propagation is that the expansion and thermal conductivity between different crystals are different. The thermal stress caused by temperature gradient and the tension or shear stress caused by the inconsistent deformation of crystals form stress concentration in weak areas such as particles boundary, cleavage, and original cracks. Firstly, it causes some crystals with smaller strength or less rounded shape to crack, and when the combined stress is large, the cracks will gradually expand along the existing fine cracks. This also explains that the most main cracks of the SF and FF path specimens mainly surround some large mineral aggregates or between particles.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

Energy demand and consumption in recent times have witnessed a rapid proliferation influenced by technological developments, increased population and economic growth. This has fuelled research trends in the domain of energy management employing tri-generation systems such as the combined cooling, heating and power (CCHP) systems. Furthermore, the incorporation of renewable energy, especially solar energy, to complement the thermal input by fossil fuels has facilitated the effectiveness and sustainability of CCHP systems. This study proposes a new approach to improve the overall efficiency of CCHP systems and compute the optimal design parameters in order to assist decision makers to identify the best geometrical configuration. A multi-objective optimization formulation of a solar-assisted CCHP system was adopted to maximize the net power, the exergy efficiency and minimize the CO2 emission using the greywolf optimization technique. In addition, the effects of the decision variables on the objective functions were analysed. The proposed optimization approach yielded 100 set of Pareto optimal solutions which would serve as options to the decision maker to make a selection in order to improve the performance of a solar-assisted CCHP system. This study demonstrates that the proposed approach is potentially suitable for the optimization of a solar-assisted CCHP system.

In Europe, the recent application of regulations oriented to zero-energy buildings and climate neutrality in 2050 has led to a reduction in energy consumption for heating and cooling in the construction sector. The thermal insulation of the building envelope plays a key role in this process and the requirements about the maximum allowable thermal transmittance are defined by country-specific guidelines. Typically, high insulation values provide low energy consumption for heating, however, they may paradoxically imply the risk of overheating in summer period and thus negatively affect the overall performance of the building. In addition, the embodied energy and related emissions caused by the manufacturing and transportation processes of thermal insulation cannot be further neglected in the evaluation of the best optimal solution. Therefore, this paper aims to evaluate the influence in terms of embodied and operational energy of various walls’ thermal insulation thicknesses on residential buildings in Europe. To this end, the EnergyPlus engine was used for the energy simulation within Ladybug &amp; Honeybee tools, by parametrically conducting multiple iterations; 53 variations of external wall U-value, considering high and low thermal mass scenarios, were simulated for 100 reference cities of the European context, using a representative multifamily building as a reference. The results demonstrate that massive walls generally perform better than lightweight structures and, of course, the best solution in terms of energy varies according to each climate. The optimal values are graphically reported on the map of Europe according to specific climatic features, providing a guidance for new constructions and building retrofit.

Combined systems for power production and thermally activated cooling have a high potential for improving the efficiency and utilisation of thermal systems. In this regard, various configurations have been proposed and are comprehensively reviewed. They are primarily based on absorption systems and the implementation of multiple levels of complexity and flexibility. The configuration of the absorption power and cooling combined cycle proposed herein has wide commercial applicability owing to its simplicity. The configuration of the components is not new. However, the utilisation of aqueous salt solutions, the comparison with ammonia chiller and with absorption power cycles, the focus on parameters that are important for real-life applications, and the comparison of the performances for constant heat input and waste heat recovery are novel. The proposed cycle is also compared with a system based on the organic Rankine cycle and vapour compression cycle. An investigation of its performance proves that the system is suitable for a given range of boundary conditions from a thermodynamic standpoint, as well as in terms of system complexity and technical feasibility. New possibilities with regard to added power production have the potential to improve the economics and promote the use of absorption chiller systems.

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

The publication presents the assessment of the influence of surface treatment such as shot-peening on the fatigue life of a compressor blade exposed to resonant vibrations. As part of the work, a geometric model of the blade was developed and a numerical modal and fatigue analysis were performed. The fatigue analysis was based on the Manson-Coffin-Basquin and Ramberg-Osgood models. As part of the work, the influence of different values of residual stresses on the results of fatigue life was determined. Additionally, the location of the highest equivalent stresses was established. The obtained results of the numerical analyzes were compared with the results presented in the scientific literature. An additional aim of the study was to determine the size of the grains at various points of the blade as well as the thickness of the layer plasticized as a result of peening. The obtained results are presented in the form of tables and charts. The relationship between the location of the highest values of equivalent stresses and the thickness of the plasticized layer was determined. The explanation of the effect of shot peening on the increase in fatigue life of the blade was proposed.

The cooling of server components has been continuously developed over the past few years in order to meet the increasing cooling requirements of server component manufacturers such as for the processor chips. The growth in performance and power density increases the cooling demand. These requirements directly influence the energy consumption and performance of the hardware. To gain a better understanding of the historical evolution and possible future technology development paths in the field of data center cooling, a patent analysis method was used. The focus is on previous and current development priorities and possible research gaps within the server and computer room levels. The European patent database was selected as data source. To determine relevant patents, the search terms for various cooling technologies were developed iteratively. After the patent extraction for the period 2000 - 2023 (earliest priority year), the search results were classified and analysed. Most of the patents deal with air or liquid cooling. In the area of liquid cooling, the focus was on direct liquid cooling, followed by total liquid cooling. Since 2015 a technological shift from air to liquid cooling can be identified on the level of patent activities. In this context, the patent groups with focus on “constructional details for different types of electric apparatus” and “electrical digital data processing” have the largest share of patents. In addition, the technology focus of the TOP 10 patent applicants was in the field of liquid cooling. In conclusion from the patent analysis, it can be derived that liquid cooling will continue to gain in importance in the future and could also be combined with other approaches in the form of hybrid cooling. However air cooling may still be relevant, even if the main cooling load is handled by liquid-based approaches. At the same time, the optimisation potential for air cooling seems to have been largely exploited in comparison to liquid cooling, as can be seen from the falling number of the patent applications.

Cooling fans are one of the critical components of air-forced (AF) dry-type transformers for regulating internal temperatures. Therefore, effective malfunction detection is crucial to maintain the transformer temperature within an acceptable range and prevent overheating. Regular maintenance occurs periodically and issues with cooling fans may arise between maintenance periods, leading to prolonged operation under malfunctioning conditions and potential failures. In addition, utilities typically have online information about whether a fan works or not without providing information about cooling fan malfunctioning circumstances. To address these challenges, this study proposes learning-based online monitoring techniques to detect malfunctions in AF transformer cooling fans. Random forests (RFs) and convolutional neural networks (CNNs) are developed to classify the audio signals from cooling fans into normal and malfunctioning classes. Unlike RFs, which require separate feature extraction, CNNs are trained based on spectrogram images derived from audio signals. Thus, various time-frequency techniques are utilized for feature extraction in RFs. Besides, multiple data augmentation techniques are employed to enhance the dataset size and diversity. Algorithmic performance is optimized through hyperparameter tuning and classifier threshold adjustment. Simulations reveal that CNNs outperform RFs, whereas the latter provides superior interpretability of acoustic features compared to the former.

This study investigates the efficiency of a biogas-powered cooling system through the utilization of energy and exergy calculations. Biogas, which can be generated and stored in small-scale plants as needed, serves as a viable fuel source for absorption cooling systems. The present research focuses on the biogas consumption of a triple-effect absorption cooling system, specifically designed to supply a fixed cooling load of 100 kW under varying operational conditions. The study highlights the COP (Coefficient of Performance) and ECOP (Exergetic Coefficient of Performance) values of the system, along with the exergy destruction rates of its individual components, at the optimal temperatures of operation. Furthermore, to determine the necessary biogas consumption, the study explores the establishment of dedicated farms for various animal species, ensuring an adequate number of animals for biogas production. The findings reveal a COP of 1.78 and an ECOP of 35.4% at the optimized operating temperatures. The minimum mass flow rate of biogas is determined to be 0.0034 kg/s, facilitating the operation of the boiler with a methane content of 65%. The study concludes that a total of 290 head of cattle is required to generate the annual biogas consumption necessary for the cooling system. Also, number of the cattle is enough to establish 284 biogas plants in Bursa province in Türkiye.

Abstract: Currently, thermal power is the largest source of power in the world. Although the impacts of climate change on cooling water sufficiency in thermal power plants have been extensively assessed globally and regionally, their economic consequences have seldom been evaluated. In this study, the Asia-Pacific Integrated Model Computable General Equilibrium model (AIM/CGE) was used to evaluate the economic consequences of projected future cooling water insufficiency on a global basis, which was simulated using the H08 global hydrological model. This approach enabled us to investigate how the physical impacts of climate change on thermal power generation influence economic activities in regions and industrial sectors. To account for the uncertainty of climate change projections, five global climate models and two representative concentration pathways (RCPs 2.6 and 8.5) were used. The ensemble-mean results showed that the global gross domestic product (GDP) loss in 2070–2095 due to cooling water insufficiency in the thermal power sector was −0.21% (−0.12%) in RCP8.5 (RCP2.6). Among the five regions, the largest GDP loss of −0.57% (−0.27%) was observed in the Middle East and Africa. Medium-scale losses of −0.18% (−0.12%) and −0.14% (−0.12%) were found in OECD90 (the member countries of the Organization for Economic Co-operation and Development as of 1990) and Eastern Europe and the Former Soviet Union, respectively. The smallest losses of −0.05% (−0.06%) and −0.09% (−0.08%) were found in Latin America and Asia, respectively. The economic impact of cooling water insufficiency was non-negligible and should be considered as one of the threats induced by climate change.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

This paper proposes a simulation technique for investigating the battery thermal management system based direct refrigerant cooling (BTMS-DRC). It employs finite element method for a combined-conduction-convection heat transfer to predict the module temperature and to prove the temperature uniformity. The refrigerant side cooling is based on the two-phase flow evaporation which is represented by the convection heat transfer (flow evaporation) under a certain refrigerant saturation temperature. The battery heat generation is modeled as the constant heat flux. The main module is modeled as the conduction heat transfer. The real BTMS-DRC is constructed for experimentation with the test bench which is based on the dual-evaporators vapour compression refrigeration system. The simulated result is validated with the experimental results to ensure the correction of the modelling. The simulation also investigates the impact of the heat generation, convection heat transfer coefficient, refrigerant saturation temperature, and thermal conductivity on the module temperature and temperature uniformity. It is found that the simulated results agree well with the experimental results. The errors are around 2.9 - 7.2% throughout the specified working conditions. Overall, the proposed technique can be used as a design tool for further developing the BTMS-DRC.

This study explores the feasibility of using an oscillating plate downstream of a cylindrical body to produce mechanical energy from a Von Kármán vortex street. The study aims to quantify the impact of the plate length, its separation from the cylinder, and a machine damping factor on the power coefficient and the blade’s displacement to identify the optimal configuration. This preliminary assessment assumes that the plate oscillation is small enough to avoid changes in the vortex dynamics. This assumption allows the construction of a surrogate model using CFD to evaluate the effect of plate length and separation from the cylinder on the fluctuating lift forces over the plate. Later, the surrogate model, combined with varying machine damping factors, facilitates the description of the device’s dynamics through the numerical integration of an angular momentum equation. The results showed that a plate with 0.52D length, 5.548D separation from the cylinder, and a damping factor of 0.013 achieved a power coefficient of 0.147 and a perpendicular displacement of 0.266D. These results demonstrate a substantial improvement in the performance of bladeless generators.

The effect of the melt cooling rate on the atomic ordering of austenite and, as a consequence, on the martensitic transformation of a nonstoichiometric alloy of the Ni-Mn-In system has been studied. In-situ TEM observations revealed differences in the mechanism of phase transformations of the alloy subjected to different cooling conditions. It is shown that during quenching a high density of antiphase boundaries (APB) is formed and the alloy is in the austenite-martensitic (10M and 14M) state up to a temperature of 120K. In a slowly cooled alloy, a lower APB density is observed, and a two-stage transformation L21/B2 → 10M → 14M occurs in the range of 150–120 K.

The present paper describes a study case of the failure investigation of Duplex stainless steel (UNS S31803) on the tube and tube sheet section of a shell and tube heat exchanger BEM TEMA type with seawater as the cooling medium. Although UNS S31803 offers high strength, high resistance to chloride-induced SCC, and high resistance to pitting attack in chloride environments, in this study case, the heat exchanger experienced some material degradation; 26 tubes were leaked and plugged on both sides, and scales plugged 76 tubes. The examination in this study case revealed the formation of biofilm inside the tubes, XRD examination revealed that the film contained aragonite (CaCO3), and by using microstructural examination on the inner surface of the tube, the austenite grains were preferentially attacked by crevice corrosion. In this case, the failure was caused by crevice corrosion, and crevice corrosion was enhanced by microbiological-induced corrosion (MIC). Recommendations to avoid similar failures are also suggested in this paper.

This paper studied the combined influences of the hot streak and swirl on the cooling performances of the NASA C3X guide vane coated with or without TBCs. The results show that: (1) Even under uniform velocity inlet conditions, the hot streak core can be stretched as it impinges the leading edge which causes higher heat load on the suction side of the forward portion. (2) The swirl significantly affects circumferential and radial migration of the hot streak core in the NGV passage. On the passage inlet plane, positive swirl leads to a hotter tip region on the suction side. In comparison, negative swirl leads to a hotter hub region on the pressure side. (3) Under the influence of swirl, migration of coolant improve the coverage of film cooling close to the midspan, while in the regions close to the hub and tip end-wall, the overall cooling performance decrease simultaneously. (4) In the regions with enough internal cooling, the cooling effectiveness increment is always larger than that in other regions. Besides, the overall cooling effectiveness increment decreases on the region covered by film cooling for the coated vane, especially in the region with negative local heat flux.

In this paper the application of the solid-state cooling based on barocaloric effect in the cold food supply chain is investigated. Barocaloric solid-state technology is applied to the final chain links of the cold food supply chain, regarding the steps of retail and domestic conservation. In this context a barocaloric cooler with regard to food needing to be kept at 5°C (273 K), in order to operate with a promising cooling technology that result energy efficient and environmentally friendly. The categories of food interested in the investigation are meets and fresh food products like soft cheese, yogurt, milk. The energy performances of the barocaloric system have been carried out and compared with a commercial vapor compression refrigerator of a similar size, both operating with R600a under the same working conditions. Basing on the following consideration one can conclude that barocaloric cooling is a favourable technology to be employed in the last link chains of the cold food supply chain if the system operates in ABR cycle at frequencies between 1.25 and 1.50 Hz with a regenerator made of acetoxy silicone rubber as solid-state refrigerant and 50%EG-50%water mixture as heat transfer fluid flowing at the optimal velocity of 0.15 m s-1 that guarantees an appropriate trade-off between the temperature span, the cooling power and the coefficient of performances. Under these conditions the barocaloric system overperforms the domestic vapor compression cooler operating with R600a.

Phase change materials (PCMs) have emerged as promising solutions for latent heat thermal energy storage (LHTES) systems, offering considerable potential for storing energy derived from renewable sources across various engineering applications. The present study focused on optimization of solar cooling system by integrating LHTES with different PCM tank configuration. TRNSYS simulation software was selected for the study and collected experimental data from laboratory system prototype was used for system validation. The results indicate that the use of PCM led to a noteworthy decrease of 6.2% in auxiliary energy consumption. Furthermore, the duration during which the heat carrier temperature flow exceeded 90°C from the storage tank to the auxiliary heater was extended by 27.8% when PCM was utilized, compared to its absence. The use of PCM in LHTES is more effective under variable weather conditions. On the day when changes in weather conditions were observed, around 98% of the cooling load was provided by produced sun energy. The results of the research can be used to optimize the solar cooling system, which will help reduce the environmental impact of cooling systems running on non-renewable fuels.

Solar assisted hybrid cooling systems are promising for the energy saving of refrigeration systems. In most cases, the solar thermal gain is only able to power the heat-driven process of facilities in part of the working period. Therefore, the reduction of compressor power strongly depends upon the duration of heat-driven processes, which has not been addressed properly. Motivated by such knowledge gap, the thermodynamic understanding of solar assisted hybrid cooling systems is deepened through considering the duration in heat-driven processes. Three absorption-compression integrated cooling cycles were taken as examples. It is found that optimal parameters, e.g., inter-stage pressure and temperature, corresponding to various performance indicators trend to be identical, as the duration of heat-driven processes is taken into account. Furthermore, the optimal parameter for different working conditions was obtained. It is displayed that the dimensionless optimal intermediate temperature of layout with the cascade condensation process varies slightly, e.g., 4%, for different conditions. Moreover, the fall of compressor power in entire working periods is nearly independent upon the intermediate temperature. The paper is favorable for the efficient design and operation of solar assisted hybrid cooling systems.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

In the case of a severe accident, natural convection plays an important role in the atmosphere mixing of nuclear reactor containments. In the previous study, to simulate the natural convection in the accident scenario within a nuclear reactor containment, the steady thermal boundary conditions (BCs) were prescribed on either cooled or heated wall. The present study, therefore, aims at the transient 3D numerical simulations of natural convection of air around a cylindrical containment with unsteady thermal BCs at the vessel wall. For that purpose, the experiment series was done in the CIGMA facility at Japan Atomic Energy Agency (JAEA). The upper vessel or both the upper vessel and the middle jacket was cooled by subcooled water, while the lower vessel was thermally insulated. A 3D model was simulated with OpenFOAM®, applying the Unsteady Reynolds-averaged Navier–Stokes equations (URANS) model. Different turbulence models were studied, such as the standard k-ε, standard k-ω, k-ω Shear Stress Transport (SST) and, low-Reynolds-k-ε Launder-Sharma. The results of the four turbulence models were compared versus the results of experimental data. The k-ω SST showed a better prediction compare to other turbulence models. Also, the accuracy of the predicted temperature and pressure were improved when the heat conduction on the internal structure, i.e., flat bar, was considered in the simulation. Otherwise, the predictions on both temperature and pressure were underestimated compared with the experimental results. Hence, the conjugate heat transfer in the internal structure inside the containment vessel must be modeled accurately.

Local thermal comfort (TC) and draught rate (DR) has been studied widely. There has been more meaningful research performed in controlled boundary condition situations than in actual work environments involving occupants. TC conditions in office buildings in Estonia have been barely investigated in the past. In this paper, the results of TC and DR assessment in five office buildings in Tallinn are presented and discussed. Studied office landscapes vary in heating, ventilation and cooling (HVAC) system parameters, room units and elements. All sample buildings were less than six years old, equipped with dedicated outdoor air ventilation system and room conditioning units. The on-site measurements consisted of TC and DR assessment with indoor climate questionnaire (ICQ). The purpose of the survey is to assess the correspondence between HVAC design and the actual situation. Results show, whether and in what extent the standard-based criteria for TC is suitable for actual usage of the occupants. Preferring one room conditioning unit type or system may not guarantee better thermal environment without draught. Although some HVAC systems observed in this study should create the prerequisites for ensuring more comfort, results show that this is not the case for all buildings in this study.

The future power equipment tends to take hydrogen or middle/low heat-value syngas as fuel for low emission. The heat transfer of film cooled turbine blade shall be influenced more by radiation. Its characteristic of conjugate heat transfer is studied experimentally and numerically in the paper by considering radiation heat transfer, multi-composition gas and TBC. The Weighted Sum of Gray Gases spectral model and Discrete Transfer Model are utilized to solve the radiative heat transfer in the multi-composition field, while validated against the experimental data for the studied cases. It is shown that the plate temperature increases significantly when considering the radiation and the temperature gradient of the film cooled plate becomes larger. It is also shown that increasing percentage of steam in gas composition results in increased temperature on the film-cooled plate. The normalized temperature of the film-cooled plate decreases about 0.02, as the total percentage of steam in hot gas increases per 7%. As for the TBC effect, it can smooth out the the temperature distribution and insulate the heat to a greater extent when the radiative heat transfer becomes significant.

The amount of heat transfer in gas turbine blades depends on cooling techniques and various flow phenomena. The effect of eddies, passing shock waves and free flow turbulence has been noticed by many researchers since the beginning. The focus of the upcoming work is on the numerical investigation of the effects of turbulence intensity and Reynolds number on the amount of heat transfer from the blade surface with internal cooling. The SST model has been used to solve this problem, which has been compared with the experimental work to ensure the correctness of the numerical simulation. In this regard, by changing the free flow turbulence intensity with values of 1, 5, 7, and 10% and at three Reynolds numbers of 150,000, 350,000, and 750,000, the changes in heat transfer coefficients have been investigated. The results show that with the increase of the turbulence intensity at different Reynolds numbers, due to the positive effect of the flow turbulence on the suppression of separation and promotion of the boundary layer transition, the blade surface heat transferincreases and this increase is more evident at higher Reynolds numbers.

Temperature Cycle Induced Deracemization (TCID) offers a promising approach to obtain enantiopure solids from racemic mixtures. By combining rapid racemization in solution and temperature swings, homochirality is theoretically achieved. Despite theoretical expectations of doubled yields compared to traditional chiral separation methods, such as in Preferential Crystallization, experimental validation remains lacking. We applied TCID to (1-(4-chlorophenyl)-4,4-dimethyl-2-(1H-1,2,4-triazol-1-yl) pentan-3-one) (Cl-TAK), introducing a post-TCID cooling step to enhance yield and a washing step to augment enantiopurity. This refinement yielded an 89.8% mass yield with 99.1% enantiomeric excess in the crystal phase (c.e.e.) within 24 hours on an 8.75g scale, showcasing improved performance with insignificant process duration extension. Additionally, we explored the stochasticity of deracemization, observing the development from low initial crystal enantiomeric excesses(1-6% c.e.e0) at a 2.5 g scale. Kinetic analysis revealed that a 2% c.e.e0 effectively mitigates chiral flipping risks and induction time in our system. Our study underscores the potential for reduced initial c.e.e. to expedite deracemization and presents a straightforward method to optimize yield and purity, facilitating industrial application.

Regeneratively cooled scramjet has already been successfully verified as propulsion device for hypersonic vehicle. As a result, dynamic process of flow and heat transfer in cooling channel is commonly occurred which may bring hazard and control difficulties for scramjet. To study transient flow and heat transfer process in cooling channel, a dynamic numerical model is established. Dynamic characteristics of flow and heat transfer under different conditions are calculated and discussed, which includes change of inlet fuel mass flow, heat flux and pressure working conditions. Results show that stable time of cooling channel outlet fuel temperature is related to the change rate of inlet mass flow and heat flux. The stable time of outlet fuel temperature under heat flux decreasing working conditions are about 12.5 s. The initial response of working pressure fluctuation will lead to fuel temperature fluctuation, which has little effect on wall temperature.

In a Water-Cooled Lithium-Lead (WCLL) Breeding Blanket (BB), the heat generated by the plasma thermal radiation and nuclear reactions is removed mainly by two components; namely, the First Wall (FW) and the Breeding Zone (BZ). The FW faces the neutrons and charged particles fluxes generated by the fusion reactions and the thermal radiation coming from the plasma. The present work takes into account the FW cooling system inspired by the WCLL BB 2018 design of DEMO 2017 baseline. Unlike the baseline where a Pressurized-Water Reactor (PWR) setup is used for the coolant, various setup between the Boiling Water Reactor (BWR) and the High-Pressure (HP) BWR are studied in the present work operating in the Two-Phase Flow (TPF) regime. The 3D model of the FW in the WCLL BB 2018 design is simplified into a 1D model and a steady state analysis is carried out to optimize the mass flow rate of the water and the number of parallel channels at the BB cells at different poloidal locations of the reactor, which helps not only in reducing the used coolant but also in improving the Tritium Breeding Ratio (TBR). The present work takes into account forced convection in the liquid only region, the subcooled boiling region, and the saturated boiling region using suitable empirical or semi-empirical models from the literature. The results are validated against the existing results in the literature. In the end, related conclusions are made regarding the pros and cons of the studied operating conditions.