In this study, a slow-release urea fertilizer hydrogel was synthesized from hydroxyl propyl methyl cellulose, polyvinyl alcohol and glycerol blends with paper (blended paper) as second layer. The fertilizer hydrogel was characterized by SEM, XRD and FTIR. Its retention in sandy soil, swelling behavior in distilled and tap water as well as slow-release behavior to urea were investigated. The results indicated that the fertilizer had good slow-release properties and ability to retain water in soil. However, the addition of blended paper as a second layer matrix was found to help improve the release properties of the fertilizer. The swelling kinetic of the hydrogel followed the Schott’s Second order model. The release kinetics of urea in water was best described by the Zero order model signifying that the release behavior was independent of fertilizer concentration

Dried blood spot (DBS) testing on confetti is one of the most common methods used to collect and extract DNA from field samples for molecular epidemiology of malaria studies. Here, we investigated whether ethanol or other solutions used to clean scissors are a source of sample contamination. DBS were prepared from 3 drops of blood from two Plasmodium falciparum cultures spotted on confetti, and 3 solutions (water, ethanol and DNase) were used to clean scissors between spots during DNA extraction. For each cleaning solution, two blank confetti were used as negative controls. Samples were analyzed by PCR-based genotyping of merozoite surface proteins 1 & 2 (msp-1 and msp-2), and P. falciparum chloroquine resistance transporter (Pfcrt). A total of 15 samples were analyzed. Based on msp-1 and msp-2 amplification, P. falciparum was detected on blank confetti when scissors were washed with ethanol. Based on Pfcrt amplification, DNA of P. falciparum was detected on blank confetti when scissors were cleaned with ethanol or water. No P. falciparum genes were detected on blank confetti when scissors were cleaned with DNase. Scissors cleaned with DNase prevented cross-contamination between samples during processing of dried blood spots, whereas ethanol (which is commonly used) fails to avert cross-contamination.

At the start of 2020 the rapid onset of the coronavirus pandemic forced higher education institutions across the world to pivot from face to face to remote teaching. For teaching methods that involve the transmission and dissemination of verbal/visual information between academic staff and students, video technologies provided immediate methods to respond to the restricted access to campus. Practical activities, that usually involve interaction with equipment, presented a greater challenge to adapt for remote delivery. With restrictions on higher education being partially lifted, many institutions worldwide intend to offer blended learning, prioritizing in-person activities that are troublesome to deliver online, such as practicals. Social distancing measures are reducing capacity and placing increased pressure on space, creating a need to optimise limited time students have in the lab and strategies to determine which activities can best utilize this limited resource. Time is constrained, leaving little opportunity to make radical changes to learning and teaching structures. In this publication, The department of Mulicdipalnary Engineering Education (MEE) at the University of Sheffield, utilise their experiences in practical teaching to provide simple, implementable ideas for blended practicals which maximize students’ learning and experiences within the envelope of available resources.

Automation is at the core of modern industry. It aims to increase production rates, decrease production costs, and reduce human intervention in order to avoid human mistakes and time delays during manufacturing. On the other hand, human assistance is usually required to customize products and reconfigure control systems through a special process interface called Human Machine Interface (HMI). Machine Learning (ML) algorithms can effectively be used to resolve this tradeoff between full automation and human assistance. This paper provides an example of the industrial application of ML algorithms to help human operators save their mental effort and avoid time delays and unintended mistakes for the sake of high production rates. Based on real-time sensor measurements, several ML algorithms have been tried to classify paper rolls according to paper grammage in a white paper mill. The performance evaluation shows that the AdaBoost algorithm is the best ML algorithm for this application with classification accuracy (CA), precision, and recall of 97.1%. The generalization of the proposed approach for achieving a cost-effective mill construction by reducing the total number of the required physical sensors will be the subject of our future research.

Blending lignin as the second most abundant polymer in nature with nanostructured compounds such as dendritic polymers will not only add value to lignin, but also increase its application in various fields. In this study, softwood Kraft lignin/polyamidoamine dendritic polymer (PAMAM) blends were fabricated by solution electrospinning method to produce bead-free nanofiber mats. The mats were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), zeta potential, and thermogravimetry analysis (TGA). The chemical intermolecular interactions between lignin functional groups and abundant amino groups in PAMAM were investigated by FTIR and viscosity measurement. These interactions enhanced the mechanical and thermal characteristics of lignin/PAMAM mats, providing further potential applications at industry level.

Environmentally friendly and low-cost sensors are needed for the next generation disposable electronics applications. Given its low-cost, availability and biodegradability, paper-based devices are a very promising. Here we demonstrate the fabrication of a tungsten disulphide (WS2) strain sensor on standard copy paper. The WS2 is deposited through direct abrasion of WS2 powder against the paper surface making the fabrication of the device low-tech and cost effective. The fabricated strain gauge devices present gauge factors up to ~70 for strains in the ± 0.5 % range. These values are ~ 9 times larger than that obtained on devices with the same geometry but using a graphite film instead a WS2 as a sensitive material. We demonstrate the potential of these WS2-on-paper strain gauges by integrating them directly on a paper cantilever to sense mass and forces. We show how this very simple device can detect sub-milligram masses. Moreover, we also demonstrate the capability of transducing motion in mechanical resonators by gluing a WS2-on-paper strain gauge on their surface.

Paper-based sensors, microfluidic platforms and electronic devices have attracted attention in the past couple of decades because they are flexible, can be recycled easily, environmentally friendly, and inexpensive. Here we report a paper aptamer-based potentiometric sensor to detect the whole Zika virus for the first time with a minimum sensitivity of 2.6 nV/Zika and the minimum detectable signal (MDS) of 1.2x10⁶ Zika. Our paper sensor works very similar to a P-N junction where a junction is formed between two different wet regions with different electrochemical potentials near each other on the paper. These two regions with slightly different ionic contents, ionic species and concentrations, produce a potential difference given by the Nernst equation. Our paper sensor consisted of a 2-3 mm x 10 mm segments of a paper with a conducting silver paint contact patches on its two ends. The paper is soaked in a buffer solution containing aptamers designed to bind to the capsid proteins on Zika. Atomic force microscopy studies were carried out to show both the aptamer and Zika become immobilized in the paper. We then added the Zika (in its own buffer) to the region close to one of the silver-paint contacts. The Zika virus (40 nm diameter with 43 kDa or 7.1x10^-20 gm weight), became immobilized in the paper’s pores and bonded with the resident aptamers creating a concentration gradient. The potential measured between the two silver paint contacts reproducibly became more negative as upon adding the Zika. We also showed that an LCD powered by the sensor, can be used to detect the sensor output.

The number of citations that a paper has received is the most commonly used indicator to measure the quality of research. Researchers, journals, and universities want to receive more citations for their scholarly publications to increase their h-index, impact factor, and ranking respectively. In this paper, we tried to analyses the effect of the number of available Google Scholar versions of a paper on citations count. We analyzed 10,162 papers which are published in Scopus database in year 2010 by Malaysian top five universities. Then we developed a software to collect the number of citations and versions of each paper from Google Scholar automatically. The result of spearman correlation coefficient revealed that there is positive significant association between the number of Google Scholar versions of a paper and the number of times a paper has been cited.

As both governments and customers push for sustainable and recyclable textile products, textile companies will have to change their linear business model to a circular one. The aim of the present work is to help these companies take action by providing an update of the state-of-the-art of textile recycling technologies. Extensive desktop research was performed in order to prepare an overview of existing textile recycling technologies, their current state and prognosis, including also facilitating technologies for sorting and disintegration of textile products as well as virtual platforms that connect stakeholders and inform consumers.

Paper-based sensors, microfluidic platforms and electronic devices have attracted attention in the past couple of decades because they are flexible, can be recycled easily, environmentally friendly, and inexpensive. Here we report a paper aptamer-based potentiometric sensor to detect the whole Zika virus for the first time with a minimum sensitivity of 2.6 nV/Zika and the minimum detectable signal (MDS) of 0.8x1e6 Zika. Our paper sensor works very similar to a P-N junction where a junction is formed between two different wet regions with different electrochemical potentials near each other on the paper. These two regions with slightly different ionic contents, ionic species and concentrations, produce a potential difference given by the Nernst equation. Our paper sensor consisted of a 2-3 mm x 10 mm segments of a paper with a conducting silver paint contact patches on its two ends. The paper is soaked in a buffer solution containing aptamers designed to bind to the capsid proteins on Zika. Atomic force microscopy studies were carried out to show both the aptamer and Zika become immobilized in the paper. We then added the Zika (in its own buffer or simulant Urine) to the region close to one of the silver-paint contacts. The Zika virus (40 nm diameter with 43 kDa or 7.1x10-20 gm weight), became immobilized in the paper’s pores and bonded with the resident aptamers creating a concentration gradient. The potential measured between the two silver paint contacts reproducibly became more negative as upon adding the Zika. We also showed that an LCD powered by the sensor, can be used to detect the sensor output.

This study investigates the contribution of nano-alumina (nA: 1-3wt.% binder) to the performance of silica fume (SF-10%) blended mortar in ternary blended mortar. The fresh (workability, setting time) and hardened properties (compressive strength and thermal resistance (300 °C for 1 h)), were examined. Nano alumina (nA) contributed positively to the consistency of SF blended mortar such that similar workability could be achieved with OPC when 3% nA was added. The initial and final setting time of 180 and 220 mins were recorded in SF blended mortar and reduced by 18.4 and 21.8%, respectively by adding 3%nA. The optimum mixture that contained 10%SF and 2%nA had 3-d and 28-d compressive strengths of 28 and 43.2 MPa. In the absence of nA, this reduced by 14.3% and 29.4% while it reduced by 25.2% and 16.7%, respectively in OPC mortar. The main products characterizing SF-nA ternary blended binder with dense microstructural density were nepheline and tobermorite. Besides, it is more susceptible to carbonation despite its superior performance in thermal resistance when compared to SF blended and OPC mortars.

This study investigates how digital alchemy can enhance literature and language teaching through a combination of online and face-to-face learning. It uses constructivist learning theory and the SAMR model to examine how digital tools and resources can transform learner engagement, critical thinking, and creativity. The study gathered data from interviews, focus groups, and document analysis with 30 participants from private HEI schools. The results show that digital alchemy through blended learning allows learners to personalize and collaborate in their exploration of various literary texts. However, the study also identifies some challenges related to resource availability and educator training. The study emphasizes the importance of using digital alchemy in literature and language teaching and suggests some ways for educators, administrators, and policymakers to effectively use digital tools and resources for student-centered teaching methods in the digital era.

Carbon dioxide, CO₂ accounts for most of the emission from all the types of greenhouse gasses in the world. The ability of CO₂ to remain longer than other greenhouse gases and the convenience of producing CO₂ has resulted in its high projection in a yearly manner. The prime factor for the emission of CO₂ are from the actions of human beings. One such human act is the concrete industry. Total emissions from the concrete industry could therefore contribute as much as 8% of global CO₂ emissions. Sequestered CO₂ in concrete can provide an impact on reducing the carbon footprint and is also able to improve the compressive strength of concrete. During this process, the sequestered carbon dioxide chemically reacts with cement to produce a mineral, trapping carbon dioxide gas in the concrete. Hence, sequestering carbon dioxide gas in concrete does not only on a bigger scale reduces carbon footprint, but it also reduces the impact the construction industry has on the environment. This paper presents a detailed review on the chemical reaction that takes place during the sequestration of carbon dioxide and the research published on the effects of carbon dioxide sequestered concrete on its properties. The impact this process has on the concrete industry and the environment is discussed in this paper.

This letter solves an open question of paper spring risen by Yoneda (2019). Universal scaling laws of a paper spring are proposed by using both dimensional analysis and data fitting. It is found that spring force obeys power square law of spring extension, however strong nonlinear to the total twist angle. Without doing any additional works, we have successfully generalize the scaling laws for Poisson ratio 0.3 to the materials with an arbitrary Poisson's ratio with the help of dimensional analysis.

In recent years, the exploration of space has expanded beyond the confines of our home planet, Earth, and has ignited a fervor for understanding the potential of sustaining life in extraterrestrial environments. One critical aspect of this endeavor is the cultivation of plants in microgravity—a unique environment that challenges traditional notions of plant growth and development. The Microgravity Plant Habitat, a cutting-edge apparatus designed to facilitate plant growth in space, stands at the forefront of scientific innovation in the quest for sustainable life beyond Earth.This research paper aims to explore into the complexities of the Microgravity Plant Habitat, exploring its design, functionality, and the profound implications it holds for future space exploration and colonization efforts. As humanity sets its sights on venturing further into the cosmos, the ability to cultivate plants in microgravity becomes paramount, not only for nutrition but also for the profound role plants play in maintaining life support systems and contributing to the psychological well-being of space travelers. Development of such plant habitat module will result in a bioregenerative life support system that will help in future deep space exploration and colonization of extraterrestrial planets. These modules can also cut the cost of space missions. The challenge of establishing outposts on the Moon or Mars requires thoughtful consideration of nourishment strategies. Space-based agriculture faces significant hurdles due to harsh conditions and limited resources. Researchers explore innovative solutions like hydroponics and aeroponics to meet nutritional needs and enhance well-being in extraterrestrial settlements. Beyond technological prowess, creating space bases demands a holistic approach, addressing biological and psychological aspects. Navigating deep space exploration emphasizes that food isn't just a logistical challenge but a symbol of our resilience and determination to thrive beyond Earth's confines.

In 2021 the total world cement production was estimated at 4.1 billion tonnes and the annual CO2 emissions from cement plants reached almost 2.8 billion metric tonnes. In the last years many ef-forts have been made for manufacturing low-CO2 cements. In this regard, a great attention has been paid towards calcium sulfoaluminate (CSA) cements for both their peculiar technical prop-erties and the environmentally friendly features mainly related to their manufacturing process. Moreover, the use of blended cements composed by CSA binders and supplementary cementitious materials (SCMs) could represents a powerful tool for both reducing the CO2 footprint and pro-ducing more durable environmentally friendly materials. In this paper, the possibility of using reservoir sediments (RS), calcined at 830°C, as SCMs in blended-CSA cements was investigated. Four binders were submitted to hydration and physico-mechanical tests for curing periods com-prised in the interval 4 hours-56 days. X-ray fluorescence, X-ray diffraction and differential thermal–thermogravimetric analyses were employed as main characterization techniques. It was found that thermally treated RS are very interesting inasmuch as their utilization allows a CSA clinker dilution, thus implying both a decrease of CO2 emissions and a reduction of costs related to CSA cement production.

The Covid-19 pandemic caused a shift in teaching practice towards blended learning for many Higher Education institutions. This led to the rapid adoption of certain digital technologies within existing teaching structures as a means to meet student access needs and facilitate learning. Integration of these technologies caused numerous challenges for practitioners and often provided mixed results. This paper is an attempt to summarise and extend pre-Covid pedagogical research to leverage digital immersive technologies for blended teaching in the post-pandemic era. Focus is given towards the evolution of Virtual Learning Environments through elements of immersive audio-visual technologies, which are shown to be effective when coupled in a blended approach. It is both a review of these methodologies and a case study of the I-Ulysses: Virtual Learning Environment as a point of comparison for evaluating the review.

Rice husk ash (RHA) is agricultural waste with high silica content that has had proven technical feasibility as a pozzolanic material since the 1970s. Notwithstanding, its use in mortars and concrete is limited by the standards currently utilized in some countries where RHA production is high and the aforementioned pozzolanic material is not standardized. This is the case of Spain, one of the main rice producers in Europe. Nowadays, the high pressure placed on the Portland cement production sector to reduce energy use and CO2 emissions has given rise to a keen interest shown in mineral admixtures for cement manufacturing. In this research, we intend to establish the contribution of different RHA types to final blended Portland cement properties (symbol “H” was used to identify RHA in standardized cements). The experimental results demonstrated that RHA with good pozzolanic properties (large specific surface and high amorphous silica content) had to be limited to 10% cement replacement because of the severe reduction in workability at higher replacement percentages. RHA with lower reactivity, such as crystalline RHA, or fly ash (FA), can be used to prepare binary and ternary blended cements with reactive RHA. It is possible to design the following cements: CEM II/A-H and CEM II/A-(H-V) It would also be possible to design cement (CEM II/B-(H-V) with replacement values up to 30% and the same 28-day mechanical performance observed for the Portland cement without mineral addition.

Paper recycling has increased in recent years. A principal consequence of this process is the problem of addressing polymeric components known as stickies. A deep characterization of stickies sampled over one year in a recycled paper industry in México was performed. Based on their chemical structure, an enzymatic assay was performed using lipases. Compounds found in stickies by Fourier-Transform Infrared spectrometry were poly (butyl-acrylate), dioctyl phthalate, poly (vinyl-acetate), and poly (vinyl-acrylate). Pulp with 4% consistency and pH=6.2 was sampled directly from the mill once macro stickies were removed. Stickies were quantified by counting the tacky macrostructures in the liquid fraction of the pulp using a Neubauer chamber before the paper was made, and they were analyzed with rhodamine dye and a UV lamp. Of the two enzymes evaluated, the best treatment condition used Lipase 30G at a concentration of 0.44 g/L, which produced a 35.59% decrease in stickies. SebOil DG showed a smaller stickies reduction of 21.5% when used at a concentration of 0.33 g/L. Stickies in kraft paper processes were actively controlled by the action of lipases, and future research should focus on how this enzyme recognizes its substrate and should apply synthetic biology to improve lipase specificity.

Usually in the manufacture of beer by fermentation of barley, in both industrialized and developing countries significant amounts of organic solid waste are produced from barley straw. These possibly have an impact on the carbon footprint with an effect on global warming. According to this, it is important to reduce environmental impact of these solid residues, and an adequate way is the recycling using them as raw material for the elaboration of handmade paper. Therefore, it is required to manage this type of waste by analyzing the environmental impact, and thus be able to identify sustainable practices for the treatment of this food waste, evaluating its life cycle, which is a useful methodology to estimate said environmental impacts. It is because of this work shows the main results obtained using the life cycle analysis (LCA) methodology, to evaluate the possible environmental impacts during the waste treatment of a brewery located in the state of Hidalgo, Mexico. The residues evaluated were barley straw, malt residues and spent grain, and at the end, barley straw was selected to determine in detail its environmental impact and its reuse, the sheets analyzed presented a grammage that varies from 66 g/m2 and 143 g/m2, resistance to burst was 117 to 145 kpa, with a crystallinity of 34.4% to 37.1%.

Abstract—as the complexity in the cloud services increases day by day the role of brokers used in the cloud gain more importance. Here we basically resolve this issue by discussing preference based cloud service recommender that support MCDM approach.^[24] The implementation and specifications details are properly discussed in a unified way to deal with the problem. SC3 is a tool that compromises capabilities of the quality assurance dimension of CSB and also it strengthen the flexibility of cloud services. The anxieties between definition procedure and implementation procedure are separated by service completeness compliance checker (SC3). Now a days companies use cloud computing for their economic benefits and market competitions that increase the demand of “cloud computing”. So for the calculation of critical success factor of “cloud computing” we focus on plan do check act strategy.

The recommendations of the panel of experts on the further development of the ‘High-Tech Strategy’ of the Government of the Federal Republic of Germany designate the biologization of economic processes along with digitization as the central driver of societal change. Various fields such as the 'biologization of materials research' were then defined in the 'Bio-Agenda' in order to walk the path from biology to innovation. In view of this perspective, we describe how the use of biological materials and mechanisms can lead to resource conservation, the production of intelligent materials and new technological and medical applications. Our strategy, based on research on ‘Biointerfaces in Technology and Medicine’, aims at the development of modular biohybrid systems that could be used as 'biofactories of the future' for sustainable production processes. To achieve this goal, in a first phase already known technologies have to be further refined and integrated in order to obtain and apply compartmentalized reaction systems on different length and time scales. In a second phase, the resulting functional units will be employed to develop dissipative systems useful for biomedical applications and advanced production processes. From a technical point of view, future success in creating 'something entirely new' will depend crucially on robust and complementary research capabilities. Since the close connection of engineering and life sciences at KIT provides an excellent basis for this endeavor, we consider the above perspectives to be feasible.

This qualitative study unveils the intricate interplay between blended learning, language and literature learning, internationalization, and the development of 21st century skills within the realm of higher education. Set against the backdrop of the environment of St. Michael's College in Iligan City, this exploration seeks to unravel the profound significance and transformative implications of these educational dimensions. By delving into the rich perspectives and experiences of 30 college students, this study addresses critical gaps in the literature and sheds light on the potential of these integrated elements. Guided by a robust theoretical framework that amalgamates renowned scholars' insights on blended learning, language acquisition, internationalization, and 21st century skills, the study employs a qualitative research design, employing interviews, observations, and document analysis. The findings illuminate the dynamic nature of blended learning, empowering students with enhanced engagement, flexibility, and accessibility in language and literature education. The incorporation of diverse literary texts and cultural perspectives fosters intercultural competence and global awareness. Moreover, the study underscores the cultivation of critical 21st century skills through immersive learning experiences. Drawing upon the insights gained, the study provides practical recommendations for educators and curriculum designers to harness the potential of blended learning, foster diversity in literary texts, and facilitate the application of 21st century skills. Recognizing the inherent limitations, including the specific context of St. Michael's College and the modest sample size, this study encourages future research to explore broader contexts and diverse participant cohorts. Overall, this illuminating study contributes to the scholarly discourse on integrating blended learning, language and literature learning, internationalization, and 21st century skills in college education. It beckons educators and policymakers to embark on a transformative journey, nurturing an enlightened future where students are equipped with the competencies to navigate the complexities of the 21st century.

This manuscript offers a concise overview of paper microfluidics, emphasizing its sustainable sensing applications in healthcare, environmental monitoring, and food safety. Researchers have developed innovative sensing platforms for detecting pathogens, pollutants, and contaminants by leveraging the paper’s unique properties, such as biodegradability and affordability. These portable, low-cost sensors facilitate rapid diagnostics and on-site analysis, making them invaluable tools for resource-limited settings. The review discusses fabrication techniques, principles, and applications of paper microfluidics, showcasing its potential to address pressing challenges and enhance human health and environmental sustainability.

Acne vulgaris has multifactorial pathogenesis which may include insulin resistance. To investigate whether insulin resistance is a causative factor in acne vulgaris development, this study and a systematic review were conducted. 41 acne vulgaris patients and 47 healthy BMI-matched controls were involved. Glucose and insulin fasting serum levels were obtained, HOMA-IR was calculated, insulin resistance was diagnosed in cases with HOMA-IR value over 2.1. The mean±SD values for glucose fasting serum level were as follows: 94.88±7.731 [mg/dl] in study group and 79.51±7.175 [mg/dl] in controls (p<0.001). The mean±SD insulin fasting serum levels were 14.47±6.394 [µIU/mL and 11.83±4.309 [µIU/mL](p=0.059), respectively. The HOMA-IR mean±SD value calculated for the study group was 3.4±1.49 and in the control group 2.34±0.909 (p<0.001).Out of 41 patients 32 were diagnosed with insulin resistance (78%) and 26 of the 47 controls 26 were diagnosed with IR (55%) (p=0.026). Insulin resistance diagnosis was statistically more common among the acne patients compared to the controls. In the articles reviewed insulin resistance was found to be more frequent in acne vulgaris patients. Both our study and the papers analysed indicate that insulin resistance might be an independent factor in acne vulgaris development and should be considered when diagnosing and treating acne.

High levels ofmeat consumption are increasingly being criticised for ethical, environmental, 2 and social reasons. Plant-based meat substitutes have been identified as healthy sources of protein in 3 comparison to meat. This alternative offers several social, environmental and health benefits and may 4 play a role in reducing meat consumption. However, there has been a lack of research on how specific 5 meat substitute attributes can influence consumers to replace or partially replace meat in their diets. 6 Research demonstrates that in many countries consumers are highly attached to meat.They consider 7 it as an essential and integral element of their daily diet. For these consumers which are not interested 8 in vegan or vegetarian alternatives to meat, so-called meathybrids could be a low-threshold option 9 for a more sustainable food consumption behaviour. In meathybrids only a fraction of the meat 10 product (e.g. 20% to 50%) is replaced with plant-based proteins. In this paper, the results of an online 11 survey with 500 German consumers are presented with focus on preferences and attitudes relating 12 to meathyrids. The results show that more than fifty percent of consumers substitute meat at least 13 occasionally. Thus, about half of the respondents reveal an eligible consumption behaviour in respect 14 to sustainability and healthiness to a certain degree. Concerning the determinants of choosing either 15 meathybrid or meat it becomes evident that the highest effect is exerted by the health perception. The 16 healthier meathybrids are perceived, the higher is the choice probability. Thus, this egoistic motive 17 seems to outperform altruistic motives like animal welfare or environmental concerns when it comes 18 to choice for this new product category.

A paper impregnated with silver nanoparticles (AgNPs) has been prepared. For the preparation of the substrates, aqueous suspensions of pulp fines, a side product from the paper production, have been mixed with Ag nanoparticles (AgNP) suspensions. The nanoparticle synthesis thereof was carried out via laser ablation of pure Ag in water. After the sheet formation process, the leaching of the AgNPs was determined to be low while the sheets exhibited antimicrobial activity towards E. Coli.

There is a growing interest in a potential use of essential oils (EOs) as a possible alternative for chemical pesticides. The formulation between different EOs could maximize the single biological efficacy by synergic mechanism. The aim of the current study was to evaluate the biological activity of three prepared blended oil formulations (BOFs) derived from Origanum vulgare L. (oregano) and Salvia officinalis L. (sage) compared to each parent EO. The chemical composition of each single studied EO has been revealed using GC-MS analysis. The three BOFs have been prepared as following: i) 25% oregano EO + 25% sage EO (BOF-I); ii) 25% oregano EO + 5% sage EO (BOF-II); iii) 5% oregano EO + 25% sage EO (BOF-III). The antibacterial activity of the new BOFs has been evaluated against Bacillus megaterium, B. cereus and Xanthomonas campestris, whereas, the antifungal activity has been carried out against Botrytis cinerea, Penicillium italicum and Fusarium oxysporum. The possible phytotoxic effect of the new BOFs has been evaluated on Lepidium sativum (garden cress), Solanum lycopersicum (tomato) and Lactuca sativa (lettuce) following the seed germination and radicle elongation assay. GC-MS analysis revealed that the oregano EO composed mainly from thymol, p-cymene and carvacrol with 76.0, 5.7 and 3.2 %, respectively. Whereas, salvia EO, the GC-MS analysis showed that the relevant predominant constituents were trans-thujone and camphor with 37,9 and 13,9 %, respectively. Results demonstrated that the tested BOFs possess antimicrobial effect higher than each parent EO. In particular, BOF-II showed the highest effect against all tested bacteria. Regarding the antifungal activity, BOF-II showed the highest significant antifungal effect against all tested fungi. Results showed also that both BOF-I and BOF-III explicated a moderate effect against B. cereus and all tested fungi compared to single EOs. In addition, the three BOFs showed notable phytotoxic effect against all three tested plants, particularly BOF-I. Whereas, the single sage EO at 25% showed the lowest significant phototoxic effect indicating its possible using as natural herbicides.

This study numerically analyzed the effect of composition and temperature and oxygen concentration changes on the selfignition characteristics of n-heptane/methane blended fuels in order to cope with development of alternative fuels and international environmental regulations. CHEMKIN-PRO is used as the analysis program and the LLNL model is used as the reaction model. The numerical results revealed that on autoignition and ignition delay time were sensitive to changes in fuel composition and oxygen concentration. As the methane ratio increases, OH radicals causing ignition are delayed in generation and the concentration is lowered, thus longer the ignition timing. The oxygen concentration in the mixed fuels are changed to simulate the exhaust gas recirculation and a numerical analysis in then performed. As the oxygen concentration decreases, the ignition delay time longer because the nitrogen gas acts as a thermal load in the combustion chamber.

The Blended Wing Body (BWB) configuration is considered to have the potential of providing significant advantages when compared to conventional aircraft designs. At the same time, numerous studies have reported that technical challenges exist in many areas of its design, including stability and control. This study aims to create a novel BWB design to test its flying and handling qualities using an engineering flight simulator and as such, to identify potential design solutions which will enhance its controllability and manoeuvrability characteristics. This aircraft is aimed toward the commercial sector with a range of 3,000 nautical miles, carrying a payload of 20,000kg. In the engineering flight simulator a flight test was undertaken; first, to determine the BWB design’s static stability through a standard commercial mission profile, and then to determine its dynamic stability characteristics through standard dynamic modes. Its flying qualities suggested its stability with a static margin of 8.652% of the Mean Aerodynamic Chord (MAC) and consistent response from the pilot input. In addition, the aircraft achieved a maximum lift-to-drag ratio of 28.1; a maximum range of 4,581 nautical miles; zero-lift drag of 0.005; and meeting all the requirements of the dynamic modes.

Understanding the complex relationship between sleep and memory is a major challenge in neuroscience. Many studies on memory consolidation in humans suggest that sleep triggers offline memory processes, resulting in less forgetting of declarative memory and performance stabilization in non-declarative memory. However, issues related to non-optimal experimental designs, task characteristics and measurements, and inappropriate data analysis practices can significantly affect the interpretation of the effect of sleep on memory. In this article, we discuss these issues and suggest constructive solutions to address them. We believe that implementing these solutions in future sleep and memory research will significantly advance this field by improving the understanding of the specific role of sleep in memory consolidation.

This study aims to exploit the distinctive properties of carbon nanotube materials, which are particularly pronounced at the microscopic scale, by deploying fabrication techniques that allow their features to be observed macroscopically. Specifically, we aim to create a semiconductor device that exhibits flexibility and the ability to modulate its electromagnetic wave absorption frequency by means of biasing. Initially, we fabricate a sheet of carbon nanotubes through a vacuum filtration process. Subsequently, phosphorus and boron elements are separately doped into the nanotube sheet, enabling it to embody the characteristics of a PN diode. Measurements indicate that, in addition to the fundamental diode's current-voltage relationship, the device also demonstrates intriguing transmission properties under the TEM mode of electromagnetic waves. It exhibits a frequency shift of approximately 2.3125 GHz for each volt of bias change. The final result is a lightweight and flexible carbon-based semiconductor microwave filter, which can conform to curved surfaces. This feat underscores the potential of such materials for innovative and effective electromagnetic wave manipulation.

Ternary blended cements such as limestone calcined clay cement (LC3) represent a strategic binder type for the mitigation of environmental impact associated with cement production and are estimated to reduce CO2 emissions by about 40% compared to ordinary Portland cement (OPC). In this paper we explore the possibility of producing such ternary blends by utilizing secondary raw materials that may be locally available. Specifically, the primary limestone that is commonly used in LC3 is here substituted by quarry dust obtained by sourcing of “kunkur”, a carbonate-rich sedimentary rock (also known as caliche) that can be locally utilized for the production of ordinary OPC clinker. To optimize the blending proportions of ternary cements consisting of OPC, calcined clay and kunkur fines, a Design of Experiment (DoE) approach was implemented, with the further goal of exploring the possibility of reducing the amount of the OPC fraction to values lower than 50%. The properties of the formulated blends were assessed by a combination of techniques that comprise mechanical strength testing, XRD time-dependent quantitative phase analysis, SEM-EDS microstructural and microchemical analysis. The results suggest that ternary blended cements based on kunkur fines form hydration products, such as hemicarboaluminates, which are also observed in LC3. This shows that such a waste material can potentially be used in sustainable cement blends, however, the presence of kaolinite in the kunkur fines seems to affect the development of strength when compared to both OPC and conventional LC3.

Previously, we described the initial use of Flipped Team‐Based learning (FTBL) defined as TBL approach combined with flipped classroom learning methodology, in which students previewed online lectures and applied their knowledge in different in-class activities. The purpose of the present study is to review the progress within this approach and to investigate how constant changes in team allocation can affect student’s perception regarding this modified FTBL approach. Although students showed reluctance initially to get out of their ‘comfort zone’, our findings show that learners perceived the adoption of the continued random allocation, and became accustomed to this learning approach, which finally assisted them to enhance their team-work skills and classroom performance, to develop their reflective capabilities as well as improving their rapport building skills, learning and academic performance. Learners also believed that this learning strategy that creates critical incidents can simulate their future work environment as they might be expected to work in unfamiliar situations. Therefore, the present study indicated strong support for the modified FTBL method and was seen to work exceptionally well, despite some minor problems that students can experience working in a team and/or with different teammates in every session.

Areca palm sheath leaves were an incredibly noble food packaging system. In ancient times, naturally available wood, leaves, stems, and barks were used to store food materials. But all these were turned down upon the rise of civilization. Today, many modern food packaging systems are used; paper and paperboard packaging materials are used mainly as a replacement for plastic materials. But somehow, paper-based materials have major drawbacks when temperature-dependent products are stored; leaching out components poses a higher threat to health. To alleviate it, bio-based components were used in the manufacturing of paper materials, but the migration of those components was still risky. This study focuses on how the areca palm sheath leaves can be effectively used to prevent this migration of components.

Although good field emission from graphene has been demonstrated from a wide variety of different microfabricated structures, very few of them can be used to improve the design of cold field emitters for electron microscopy applications. Most of them consist of densely packed nano-emitters, which produce a large array of defocused overlapping electron beams, and therefore cannot be subsequently focused down to a single nanometer electron probe. This paper reviews the kind of single-tip cathode structures suitable in cold field emission guns for instruments such as scanning electron microscopy, transmission electron microscope or scanning transmission electron microscopy, and reviews progress in fabricating them from graphene-based materials.

This study employs a qualitative research approach to investigate the intrinsic and extrinsic motivations that influence college students' engagement, learning experiences, and long-term commitment to language and literature studies within the context of blended learning modality. Drawing on the theoretical frameworks of Self-Determination Theory and Achievement Goal Theory, the research explores the complex interplay between intrinsic factors (e.g., passion, self-improvement, personal growth) and extrinsic factors (e.g., external rewards, recognition). The study is conducted at SMC among the 30 participant and utilizes interviews and classroom observations, in conjunction with a comprehensive review of relevant literature, to gain insights into the impact of these motivations on academic performance and learning outcomes, particularly in blended learning environments. The study acknowledges the limitations inherent in its locale-specific scope and the challenges associated with ensuring the validity and reliability of data collected through online surveys and virtual classroom observations. The findings of this study have significant implications for educators and policymakers, highlighting the importance of nurturing intrinsic motivation while leveraging extrinsic factors to establish supportive learning environments that foster student autonomy, incorporate student interests, and provide timely feedback. By comprehending the motivations that drive student engagement and long-term commitment, educators can enhance learning experiences, elevate academic performance, and sustain students' engagement with language and literature studies amidst the evolving educational landscape of blended learning modality.

The period of the COVID-19 pandemic resulted in a rapid development of innovative education methods, in particular using e-learning and remote work tools. The effects of this development are also post-pandemic changes in formal teaching regulations, in particular in higher education, allowing classes and lectures to be carried out with Blended Learning or Flipped Classroom methods. This paper provides information about a case study of implementing ICT technologies with elements of the mentioned methods in one of the subjects at a technical university. The implemented tools and solutions in the field of e-learning and interactivity are presented, along with information regarding their perception by students during two academic years in the post-COVID-19 period. The analysis of results of these information and student evaluations indicates their generally positive approach to such innovations in the educational path, and at the same time shows significant challenges for teachers to increase the attractiveness and effectiveness of the teaching process and the development of practical, technical skills of students.

Blended learning, the integration of online and face-to-face instruction, has garnered attention in education. This paper aims to explore challenges in blended learning faced by students, teachers, and parents and propose mitigating strategies. The study employed qualitative research methods and involved 30 participants from St. Michael's College. Findings revealed primary challenges, including technical difficulties, time management, lack of interaction, and varying digital literacy levels. These challenges influenced engagement, communication, and student achievement. The study utilized a theoretical framework encompassing Technological Pedagogical Content Knowledge, Social Presence Theory, and Activity Theory. Strategies recommended comprise providing technical support, promoting communication and collaboration, offering professional development, and leveraging learning analytics. The study contributes to the existing literature by identifying specific challenges and proposing practical recommendations for enhancing blended learning effectiveness. Limitations include a small sample size and context-specific findings. Future research should investigate these challenges in broader settings and examine the long-term effects of the recommended strategies. Addressing blended learning challenges can empower educators, administrators, and policymakers to create supportive and effective learning environments for all stakeholders involved.

The opportunities and advantages of implementing Artificial Intelligence (AI) and Machine Learning (ML) to optimize the process control of wastewater treatment in the Oil and Gas industry are discussed in this work. Discussion is centered around five major points: 1) Various types of Oil and Gas wastewater (Sour, Oily, Produced) and industry standards/methods for treatment, including specific case studies and challenges when treating certain wastewater. This section aims at the common types of wastewater in the Oil and Gas industry and how they are generally treated. 2) How AI/ML has been implemented in wastewater treatment in various industries; summary of which AI/ML languages were used along with a brief overview of how they work. This article focused on an understanding of the specific case studies and AI explanations to understand the effectiveness of wastewater treatment using AI/ML. 3) AI that is currently implemented in Oil and Gas such as personal protective equipment (PPE), smartwatches radiofrequency identification etc. This showed that AI/ML already plays a successful role in the Oil and Gas industry and has proven to help optimize many processes and components. Many of these AI/ML implementations are now industry standards and have greatly benefitted the industry. This section demonstrates that the implementation and the use of AI/ML have been proven to be a successful endeavor and that expanding the role of AI/ML would be beneficial. 5) Using the established points from the previous sections the paper outlines why AI/ML is ideal for Oil and Gas wastewater treatment; this argument centers around fit-for-purpose treatment, and the possible uses of the treated water. A determination of the best-suited AI languages, possible implementation scenarios, and how this would shift the way Oil and Gas industries treat and approach wastewater is presented to the reader.

Carbon fibers (CFs) cannot be directly used for the preparation of CF paper because of their chemically inert nature. Herein, the surface of CF was modified via the spontaneous oxidative self-polymerization of dopamine. By taking full advantage of the spontaneous oxidation and self-polymerization properties of PD to maintain the maximum strength of CFs, a polydopamine-modified CF paper (PDA-CFP) with excellent performance was prepared using PD-modified CFs (PDA-CFs), which increased the proportion of hydrophilic functional groups on the surface of carbon fibers, increased the O/C ratio on the CF surface by 6 times, and improved the bond strength between the modified CF and the adhesive by making full use of the interaction force between polydopamine and PVA fibers. In this way, the primary properties of the CF paper was improved. Overall, the results showed that the dispersion of CF was considerably improved by the dopamine modification. In addition, the primary physical properties of PDA-CFP were better than those of virgin CF paper (CFP-0). PDA-CFP exhibited a maximum tensile strength of 2.04 kN/m2, a minimum resistivity of 0.06055 Ω·cm and a minimum porosity of 72.4%. The tightness could be increased by up to 12.1%.

Several types of hematite nanoparticles (α-Fe2O3) have been investigated for their effects on the structure and properties of fly ash (FA) blended cement. All synthesized nanoparticles were found to be spherical shape, but of different particle sizes from 10 to 195 nm depending on the surfactant used in their preparation. The cement hydration with time showed 1.0% α-Fe2O3 nanoparticles was an effective accelerator for FA blended cement. Moreover, adding α-Fe2O3 nanoparticles in FA blended cement enhanced the compressive strength and workability of cement. Nanoparticle size and size distribution were important for optimal filling of various size of pores within the cement structure.

Education on Innovation and Entrepreneurship (I&E) has increased in the last two decades, specially, through MOOCs. Lately, these reusable online alternatives have tended to be revalorized by HEIs into blended learning activities, posing new challenges for instructors, specially, on how to bridge prior knowledge with in-class activities. Adopting a discursive approach to knowledge, our proposal aims to meet this challenge by identifying student’s ‘representations’, i.e., patterned constructions on disciplinary knowledge. Representations can be found across different cohorts and thus further complemented by instructors. To test this assumption and build our proposal, we analysed student’s representations in two observations. We mapped students’ representations over key I&E definitions (e.g., ‘start-up’) and, to know how prior knowledge may be complemented by instructors, we identified students’ alignment with expert disciplinary knowledge. Firstly, we found that the two cohorts tended to express representations by turning attention to several dimensions, e.g., referring to different types of features or finalities associated with concepts. Secondly, the disciplinary alignment description revealed that students tended to focus on the same components present in experts’ definitions, but with a greater level of generality. Our results have been packaged into a proposal that aims to help instructors scale their blended activities.

Delve into the ebb and flow of human ingenuity as the researcher traces the evolution of writing from papyrus to pixels. Discover how humble instruments like quill pens and typewriters have propelled human into the digital frontier, forever reshaping the art of expression in the modern age. This article examines the evolution of writing tools from traditional pen and paper to digital writing in the modern age. It explores the development of writing materials such as papyrus, parchment, and paper, as well as the invention of writing tools including quill pens, fountain pens, and typewriters. The rise of digital writing tools, including word processing software and smartphones, is also discussed, along with their benefits such as increased efficiency and productivity, enhanced collaboration and sharing capabilities, and greater accessibility and flexibility. However, the article also highlights the challenges of writing in the digital age, including the impact of digital distractions on writing focus and quality, the issue of online plagiarism and copyright infringement, and the potential loss of traditional writing skills. The article concludes with recommendations for educators, school administrators, students, and researchers to strike a balance between digital and traditional writing practices, to embrace digital writing tools while preserving traditional writing skills, and to understand the importance of the evolution of writing. The theoretical frameworks of Social Construction of Technology (SCOT) Theory, Media Ecology Theory, and Activity Theory are also discussed in relation to the evolution of writing tools. Overall, this article provides valuable insights into the history, benefits, and challenges of writing in the digital age, as well as suggestions for navigating the future of writing and its tools.

Polymeric wet-strength agents are important additives used in the paper industry to improve the mechanical properties of paper products, especially when they come in contact with water. These agents play a crucial role in enhancing the durability, strength, and dimensional stability of paper products. The aim of this review is to provide an overview of the different types of wet-strength agents available and their mechanisms of action. We will also discuss the challenges associated with the use of wet-strength agents and the recent advances in the development of more sustainable and environmentally friendly agents. As the demand for more sustainable and durable paper products continues to grow, the use of wet strength agents is expected to increase in the coming years.

Paper-based analytical devices have been substantially developed in recent decades. Many fabrication techniques for paper-based analytical devices have been demonstrated and reported. Herein we report a relatively rapid, simple, and inexpensive method for fabricating paper-based analytical devices using parafilm hot pressing. We studied and optimized the effect of the key fabrication parameters, namely pressure, temperature, and pressing time. We discerned the optimal conditions, including pressure of 3.8 MPa (3 tons), temperature of 80oC, and 3 minutes of pressing time, with the smallest hydrophobic barrier size (821 µm) being governed by laminate mask and parafilm dispersal from pressure and heat. Physical and biochemical properties were evaluated to substantiate the paper functionality for analytical devices. Wicking speed in the fabricated paper strips was slightly slower than that of non-processed paper, resulting from reducing paper pore size. A colorimetric immunological assay was performed to demonstrate the protein binding capacity of the paper-based device after exposure to pressure and heat from the fabrication. Moreover, mixing in two-dimensional paper-based device and flowing in a three-dimensional counterpart were thoroughly investigated, demonstrating that the paper device from this fabrication process is potentially applicable as analytical devices for biomolecule detection. Fast, easy, and inexpensive parafilm hot press fabrication presents an opportunity for researchers to develop paper-based analytical devices in resource-limited environments.

In an increasingly changing world, critical thinking is one of the key skills that ensure organisations' competitive advantage. Thus, in higher education institutions there is an accelerating emphasis on developing critical thinking (CT) among students. This paper presents the results of three experimental courses (Pedagogy and didactics of financial accounting, Virtual Learning Environments in Economics, Business Communication), using a blended learning method, aimed at improving students' CT skills. The three courses were delivered by both higher education teachers and trainers from the labour market. After analysing the data from the three experimental courses, it will be possible to assess whether the intervention of labour market trainers contributed to the improvement of students' critical thinking skills, and, in particularly at the level of which components improvements have been identified.

The objective of parsing is to transform a natural language sentence it in to a standard order. and in a same way a sentence is tokenized with an appropriate format. There are certain English grammar evaluation rules and the parsing approach which is to be followed for the proper formation of a particular sentence syntactically and semantically using the parsing approach. A sentence in English language is the main element in the semantic parser, which creates a parse tree with the help of applying semantic dating technique to a number of phrases. A parser divides a token into smaller components by applying sets of guidelines that characterize and a series of the tokens to determine its structure of the language, which specified by grammar. The illustration provides easy records on grammatical connections, which can simply know and put into practice with those who have no prior knowledge of the language, such as those who need to obtain textual family members. The semantic family members represent the relationships of a number of the words in the sentence. We advocate utilizing our parser to acquire the tagged sets as well as a context-free layout grammatical representation for the source form. All pronouns, adverbs, singular, plural, nouns, verbs, people, adjectives, tenses and other words are kept in a database.

The Covid-19 coronavirus, SARS-CoV-2, is inactivated much faster on paper (3h) than on plastic (7d). By classifying materials according to virus stability on their surface, the following list is obtained (from long to short stability): polypropylene (mask), plastic, glass, stainless steel, pig skin, cardboard, banknote, cotton, wood, paper, tissue, copper. These observations and other studies suggest that SARS-CoV-2 may be inactivated by dryness on water absorbent porous materials but sheltered by long-persisting micro-droplets of water on waterproof surfaces. If such physical phenomenons were confirmed by direct evidence, the persistence of the virus on any surface could be predicted, and new porous objects could be designed to eliminate the virus faster.

The main purpose of this research is to use “DMAIC” and “DMADV” framework of six sigma to reduce cost of projects, increase yields, improve performance and reduce defects. This study conclude that the sigma level of cement bag production in four production lines is “4.7 DPMO” values of 710 and the possibility of defects per unit of 11 possibilities this situation was handled by using six sigma. Any business or industry run only to satisfy customer and increase their profits, this can be attained as development of quality product..For the ranking of newly established universities the certification of those institutes is very important and also a critical process. For this process we used Lean six sigma approach that can identify the wastes that affect this process.Six sigma can be applied to any work field such as education, power optimization and other types of industries Six sigma “DMAIC” approach is also used for the testing of EDA tools that occurs due to the complex coding or configurations, flows and platforms they support. To improve the process quality of SDLC it’s necessary to remove the defects of system in advance along with thorough valuation of size and it also makes project accordant with real time environment

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

The research hypothesis states that the impregnation of the honeycomb paper core of lightweight sandwich panels with modified starch, sodium silicate and LiquidWood® resin has a significant effect on the elastic properties of it. In the study, a recycled paper was used in three thicknesses, seven types of cell shapes, including two after numerical optimization and three types of impregnating agents. The method of digital image analysis determined the elastic constants of manufactured paper cores, which were subjected to axial compression in two directions. Based on the experimental results, elastic constants of the cores were calculated and compared with the results of numerical calculations. It has been shown that each of the impregnating solutions used improves the stiffness of the paper core. The best results were obtained for LiquidWood® epoxy resin and modified starch. An important parameter of cell geometry affecting their rigidity is the angle of the cell wall φ, as well as the arrangement of the common cell wall in relation to the direction of load. The numerical models developed were positively verified.

This study investigates the impact of plasma gradient modification and gradient illumination on the optoelectronic properties of buckypaper (BP), a flexible and large-scale material composed of multi-walled carbon nanotubes (MWCNTs). The BP samples were subjected to argon ion plasma treatment at varying power levels and durations, thereby creating different carrier concentration gradients on the surface. The photovoltage and photocurrent responses of the samples were then measured under uniform full illumination and gradient illumination conditions. The findings revealed that both plasma gradient modification and gradient illumination significantly enhanced the optoelectronic performance of BP. Notably, the combined application of these two methods yielded superior results compared to the application of either method alone. Specifically, the optimal plasma power for improving BP was found to be 20W. Under conditions of plasma gradient modification and gradient illumination, a photovoltage of 267.76 μV was generated, which represents a 21.44 times increase, and a photocurrent of 15.69 μA, reflecting a 32.69 times enhancement. The mechanism underlying this optoelectronic effect can be attributed to the presence of π-bonds in the carbon atoms. These π-bonds are excited by photons, resulting in the generation of small voltages and currents. This study underscores the potential of BP as an optoelectronic material and introduces a novel approach to enhance its optoelectronic properties through plasma gradient modification and gradient illumination.

A recent manuscript (Zhou, P. et al. “A pneumonia outbreak associated with a new coronavirus of probable bat origin”, Nature 579, 270–273 (2020). https://doi.org/10.1038/s41586-020-2012-7) from Wuhan Institute of Virology claimed the identification of a bat coronavirus, RaTG13, which showed 96.2% genome homology with SARS-CoV-2. In this paper, we raise the puzzling observations surrounding the identification, characterization, unique genome features of this RaTG13 strain, as well as its 100% nucleotide identity in partial RdRp gene with another bat coronavirus strain BtCoV/4991. And the paper presented premature hypothesis of potential bat origin of SARS-CoV-2 while RaTG13 strain was not successfully isolated. We also present the concerns on the methodology, data quality and experiment procedures described in this paper. We call for the authors to provide additional data, to share related samples to be verified and further characterized by other scientists.

Background Increasingly, healthcare organizations are using technology for the efficient management of data. The aim of this study was to compare the data quality of digital records with the quality of the corresponding paper-based records by using data quality assessment framework. Methodology We conducted a desk review of paper-based and digital records over the study duration from April 2016 to July 2016 at six enrolled TB clinics. We input all data fields of the patient treatment (TB01) card into a spreadsheet-based template to undertake a field-to-field comparison of the shared fields between TB01 and digital data. Findings A total of 117 TB01 cards were prepared at six enrolled sites, whereas just 50% of the records (n=59; 59 out of 117 TB01 cards) were digitized. There were 1,239 comparable data fields, out of which 65% (n=803) were correctly matched between paper based and digital records. However, 35% of the data fields (n=436) had anomalies, either in paper-based records or in digital records. 1.9 data quality issues were calculated per digital patient record, whereas it was 2.1 issues per record for paper-based record. Based on the analysis of valid data quality issues, it was found that there were more data quality issues in paper-based records (n=123) than in digital records (n=110). Conclusion There were fewer data quality issues in digital records as compared to the corresponding paper-based records. Greater use of mobile data capture and continued use of the data quality assessment framework can deliver more meaningful information for decision making.

The interest in flying wings dates as far the early years of the aviation age. Over the 20th century, numerous attempts were made to investigate the feasibility of the concept, which demonstrated numerous early benefits: increased aerodynamic efficiency, reduced fuel consumption and lower noise and pollutant emissions compared to conventional tube and wing aircraft. However, major technical challenges prevented that type of design from entering mass production, especially with regards to structural design and manufacturing, stability and control and ride quality. In the 1990’s, a new concept, the blended wing body (BWB), was created to alleviate some of the concerns of flying wings while maintaining increased efficiency. Despite the promise, technical hurdles once again proved to be a deal breaker, and as of 2024, the only flying wing to enter serial production is the B-2 Spirit, an extremely complex and expensive aircraft. Thirty years later, as the world is quickly transitioning towards cleaner energy, the interest in the blended wing body has been renewed. The latest technological advancements in the aerospace industry should make the development of the BWB more plausible, however passenger comfort issues remain. Surprisingly, the BWB development may come from an unexpected application: as a tanker aircraft. As the U.S. Air Force is seeking a replacement to hundreds of aging tankers, a startup company was recently funded to develop the concept and build a prototype. In this study, we explore the history of blended designs from its early days, highlighting its opportunities and challenges – and why the design is an intriguing fit for application as a tanker aircraft.

In this study, the changes in mass, compressive strength and length were analyzed to investigate sulfate resistance according to ground granulated blast furnace slag (GGBFS) blending ratio and type of sulfate solution. All alkali activated mortars showed excellent sulfate resistance when immersed in sodium sulfate (Na₂SO₄) solution. However, when immersed in magnesium sulfate (MgSO₄) solution, different sulfate resistance results were obtained depending on the presence of GGBFS. Alkali activated GGBFS blended mortars showed a tendency to increase mass, increase length and decrease compressive strength when immersed in magnesium sulfate solution, but the alkali activated FA mortars did not show any significant difference depending on the types of sulfate solution. The deterioration of alkali activated GGBFS blended mortars in the immersion of magnesium sulfate solution was confirmed by the decomposition of C-S-H which is the reaction product by magnesium ion and the formation of gypsum (CaSO₄·2H₂O) and brucite (Mg(OH)₂).

A new biodegradable paper-based film is a hot research topic in the development of green agriculture. In this paper, a black paper base film coated with cooked tung oil with excellent mechanical properties, hydrophobic surface, high heat transfer and strong weather resistance was prepared by spraying high pigment carbon black solution on the surface of base paper. The results showed that the surface solidified oil film with rough structure was made by the brush coating process of cooked tung oil, and the base film of black paper was given hydrophobic structure, and the contact angle reached 98.9 °. Cooked tung oil permeates into the inside of the paper base, and after curing, it forms a multi-dimensional network film structure. The maximum tensile stress of the black paper base film is about 123% higher than that of the original paper base film. The coloring of carbon black makes the black paper base film have heat conduction effect, and the average heat transfer rate reaches 15.12 °C/s. Cooked tung oil is combined with the paper-based fiber high-toughness layer to form a stable system. The existence of the cured film improves the basic mechanics and hydrophobicity, and the resistance to ultraviolet radiation and hot air is greatly improved. This study provides a feasible scheme for the application of a black paper base film coated with cooked tung oil.

We fabricate paper-supported semiconducting devices by rubbing a layered molybdenum disulfide (MoS₂) crystal onto a piece of paper, similarly to the action of drawing/writing with a pencil on paper. We show that the abrasion between the MoS₂ crystal and the paper substrate efficiently exfoliates the crystals, breaking the weak van der Waals interlayer bonds and leading to the deposition of a film of interconnected MoS₂ platelets. Employing this simple method, that can be easily extended to other 2D materials, we fabricate MoS₂-on-paper broadband photodectectors with spectral sensitivity from the ultraviolet (UV) to the near-infrared (NIR). We also used these paper-based photodetectors to acquire pictures of objects by mounting the photodetectors in a homebuilt single-pixel camera setup.

Metal nanoparticle has been reported to have a high antimicrobial activity against fungi, bacteria, and yeasts. In this study, silver nanoparticles (AgNPs) were synthesized using a chemical reduction method, at 90 oC, and used as an antifungal coating in paper packaging, to control the growth of C. gloeosporioides in cut orchid flowers during shipping. AgNPs were characterized by UV-Vis spectroscopy and atomic force microscope (AFM). The results indicated that the shape of AgNPs was spherical and homogenous with an average size of 47 nm. Twenty and 50 particles per million (ppm) concentration of AgNPs, mixed with starch, were prepared as the coating solution. The paper coated with 50 ppm AgNPs exhibited a significant antifungal activity against C. gloeosporioides compared to 20 ppm AgNPs coating. The AgNPs coated paper had a better water resistance and mechanical properties compared to paper without coating. We observed a significant reduction in the number of anthers, of orchid inflorescences, infected by C. gloeosporioides, when stored in the coated boxes. The current study demonstrates that paper boxes coated with AgNPs are a potential solution to control the infection of C. gloeosporioides in the storage of cut orchid flowers.

Oil immersed paper insulation condition is a crucial aspect of power transformer’s life condition diagnostic. The measurement testing database collected over the years made it possible for researchers to implement classification analysis to in-service power transformer. This article presents classification analysis of transformer oil-immersed paper insulation condition. The measurements data (dielectric characteristics, dissolved gas analysis, and furanic compounds) of 149 transformers with primary voltage of 150 kV had been gathered and analyzed. The algorithm used for developing classification model is Support Vector Machine (SVM). The model has been trained and tested using different datasets. Different models have been created and the best chosen, resulting in 90.63% accuracy in predicting the oil-immersed paper insulation condition. Further implementation was executed to classify oil-paper condition of 19 Transformers which Furan data is not available. The classification results combined, reviewed, and compared to conventional assessment methods and standards, confirming that the model developed has the ability to do classification of current oil-paper condition based on Dissolved Gasses and Dielectric Characteristics.

The recyclable paper based on photochromic materials not only reduces the pollution in the paper manufacture process, but also reduces the pollution caused by the use of ink, which receives wide attention. In this paper, a serial of PMoA-PWA/ZnO/PVP hybrid films which had different ratio of PMoA/PWA was prepared by the ultrasonic composite method. The results indicated that the hybrid film prepared when the ratio of PMoA to PWA was 3 had the best photochromic performance. In this system, ZnO was the photosensitizer while PMoA/PWA was the chromophore. The photochromic mechanism of PMoA-PWA/ZnO/PVP hybrid film was based on the photogenerated electron transfer mechanism. ZnO generated photoelectron under the excitation of visible light, then PMoA and PWA obtained the photoelectron and produced photoreduction reaction to generate heteropolyblue. The visible light photochromic paper was prepared by loaded PMoA-PWA/ZnO/PVP hybrid film (A3) on A4 paper. Application test showed that the prepared paper had extremely stable, excellent and reversible visible light photochromic properties, whether it was printing patterns or words and could replace the ordinary paper to realize the reuse of paper.

Here, we designed the composition of the coating of the paper sheets composed of chitosan, bacterial cellulose (nanofibres), and ZnO with boosted antibacterial and mechanical activity. We investigated the compositions with ZnO exhibiting two different sizes/shapes: (1) rods and (2) irregular sphere-like particles. The proposed processing of bacterial cellulose resulted in the formation of nanofibers. Antimicrobial behavior was tested using E. coli ATCC® 25922™ following ASTM E2149-13a standard. Mechanical properties of the paper sheets were measured by comparison of tearing resistance, tensile strength, and bursting strength according to ISO 5270 standard. The increased antibacterial response is assigned to the combination of chitosan and ZnO (independently of its shape and size), while the boosted mechanical behavior is due to bacterial cellulose nanofibers. Therefore, the proposed composition is an interesting multifunctional mixture for coatings in food packaging applications.

The production of photovoltaic modules is increasing to reduce greenhouse gas emissions. However, this results in a significant amount of waste at the end of their lifespan. Therefore, recycling these solar panels is important for environmental and economic reasons. However, collecting and separating Crystalline silicon, Cadmium Telluride, and Copper indium gallium selenide panels can be challenging, especially in underdeveloped countries. The innovation of this work is to develop a process to recycle all solar panel waste. The dissolution of all metals is studied through the leaching process as the main step of the flowchart. In the first step of leaching, silver can be recovered 98% by 0.5 nitric acid. Then, the second and third step involves the use of glycine for base metals dissolution, followed by the leaching of valuable metals with hydrochloric acid. The effect of parameters such as initial pH, acid concentration, solid/liquid ratio, and Hydrogen peroxide concentration are studied. The results show that Cu, Pb, Sn, Zn, Cd, In, Ga, and Se can be recovered until about 100% under optimal conditions. The optimal conditions for the dissolution of Cu, Zn, and Cd were the glycine concentration of 0.5 M, Temperature of 25 ˚C, the solid/liquid ratio of 10 gr/l, and 1% of Hydrogen peroxide. The optimized glycine concentration for the leaching of lead and tin was 1.5M. Indium and gallium were recovered to 100% by the use of 5M Hydrochloric acid, S/L=10gr/l, and T=45 ˚C. Separation of selenium and tellurium occurred by 0.5 M HCl at a temperature of 60 ˚C. Additionally, for the first time, a general outlook for the recycling of various end-of-life solar panels is suggested.

We report on an immunofluorescent paper-based assay for the detection of severe acute respiratory symptom coronavirus 2 (SARS-CoV-2) humanized antibody. The paper-based device was fabricated by using lamination technique for easy and optimized handling. Our approach utilises a two-step strategy that involves (i) initial coating of the paper-electrode with recombinant SARS-CoV-2 nucleocapsid antigen to capture the target SARS-CoV-2 specific antibodies, and (ii) subsequent detection of SARS-CoV-2 antibodies using fluorophore-conjugated IgG antibody. The fluorescence readout was observed with fluorescence microscopy. The images were processed and quantified using a MATLAB program. The assay can selectively detect SARS-CoV-2 humanized antibodies spiked in PBS and healthy human serum samples with the relative standard deviation of approximately 6.4% (for n = 3). It has broad dynamic ranges (1 ng to 50 ng/µL in PBS and 5 to 100 ng/µL in human serum samples) for SARS-CoV-2 humanized antibodies with the detection limits of 2 ng/µL (0.025 IU/mL) and 10 ng/µL (0.125 IU/mL) in PBS and human serum samples, respectively. We believe that our assay has the potential to be used as a simple, rapid, and inexpensive paper-based diagnostic device with a portable fluorescent reader to provide point-of-care diagnosis. This assay can be used for rapid examination of a large batch of samples toward clinical screening of SARS-CoV-2 specific antibodies as a confirmed infected active case or to evaluate the immune response to a SARS-CoV-2 vaccine.

Headaches are among the most prevalent and disabling disorders and there are several patients’ unmet needs in current pharmacological options, while a growing interest is focusing on nutritional approaches as non-pharmacological treatments. Among these, the most promising seems to be the ketogenic diet (KD). Exactly 100 years ago, KD was used to treat pediatric forms of drug-resistant epilepsy, but progressively applications of this diet also involved adults and other neurological disorders. Evidence of KD effectiveness in migraine comes from 1928, but in the last years different groups of research and clinicians paid attention to this therapeutic option to treat patients with drug resistant migraine and cluster headache, and/or comorbid with metabolic syndrome. Here we describe all the existing evidence on the potential benefits of KDs in headaches, explore in deep all the potential mechanisms of action involved in the efficacy, and synthesize results of working meetings of an Italian panel of experts on this topic. Aim of the working group is the creation of a consensus on indications and clinical practice to treat with KDs patients with headache. The results here we present are the base for further improvement in the knowledge and application of KDs in the treatment of headaches.

Buckypaper (BP), a flexible and porous material, exhibits photovoltaic properties when exposed to light. In this study, we have employed Radio Frequency (RF) Sputtering of Zinc Oxide (ZnO) followed by rapid thermal annealing to enhance the photovoltaic response of BP. We investigated the impact of various sputtering parameters, such as the gas flow ratio of argon to oxygen and deposition time, on the morphology, composition, resistivity, and photovoltaic characteristics of ZnO-modified BP. Additionally, the photovoltaic performance of the samples under different illumination modes and wavelengths was compared. It was found that optimal sputtering conditions—argon to oxygen flow ratio of 1:2, deposition time of 20 minutes, and power of 100 watts—resulted in a ZnO film thickness of approximately 45 nanometers. After annealing at 400°C for 10 minutes, the ZnO-modified BP demonstrated a significant increase in photocurrent and photovoltage, along with a reduction in resistivity, compared to unmodified BP. Moreover, under gradient illumination, the ZnO-modified BP exhibited a photovoltage enhancement of 14.70 times and a photocurrent increase of 13.86 times, compared to uniform illumination. Under blue light, it showed a higher photovoltaic response than under other colors. The enhancement in photovoltaic response is attributed to the formation of a Schottky junction between ZnO and BP, an increased carrier concentration gradient, and an expanded light absorption spectrum. Our results validate that ZnO sputtering followed by annealing is an effective method for modifying BP for photovoltaic applications such as solar cells and photodetectors.

Emerging evidence has shown that microRNAs play pivotal roles in wound healing. MicroRNA-21 (miR-21) was previously found to upregulate in order to fulfill an anti-inflammation role for wounds. Exosomal miRNAs have been identified and explored as essential markers for diagnostic medicine. However, the role of exosomal miR-21 in wounds has yet to be well studied. In order to facilitate the early management of poorly healing wounds, we developed an easy-to-use, rapid, paper-based microfluidic-exosomal miR-21 extraction device to determine wound prognosis in a timely manner. We isolated and then quantitatively examined exosomal miR-21 in wound fluids from normal tissues, acute and chronic wounds. Eight improving wounds displayed lower levels of exosomal miR-21 expression after wound debridement. However, four instances of increased exosomal miR-21 expression levels were notably associated with patients with poor healing wounds despite aggressive wound debridement, indicating a predictive role of tissue exosomal miR-21 for wound outcome. Paper-based nucleic acid extraction device provides a rapid and user-friendly approach for evaluating exosomal miR-21 in wound fluids as a means of monitoring wounds. Our data suggest that tissue exosomal miR-21 is a reliable marker for determining current wound status.

This review paper aimed at reviewing English language teaching articles on EFL teachers’ perceptions, practices and challenges towards communicative language teaching. In this review, two ELT articles, which have been conducted on teachers’ perceptions, practices and challenges towards communicative language teaching in EFL classes, were reviewed in detail. While reviewing the articles, the researcher adapted Rideley’s (2008) checklist to evaluate elements of article. Thus, articles were reviewed by focusing on the title, abstract, introduction, research questions, objectives, research design, participants, sample and sampling techniques, data collecting instruments, methods of data analyses, findings and references based on the checklist provided above. The review revealed that the articles had clear objectives, researchable questions, appropriate methods and inevitable conclusions. They tried to answer the questions which were raised in each article, and the objectives went along with the overall research findings. The review, on the other hand, revealed that the participants in the articles were not representative so as to conclude and generalize the overall population by taking only few participants which were selected even by using non probability sampling.

University-Business partnership for collaborative curriculum design, development and delivery is possibly the less explored dimension of University Business Collaboration (UBC). Even if some models for curricular design and development might be available, scarce information exists on how the partnership is constructed, the new curricula are designed, developed and how they are implemented. This article intends to present and discuss the experience obtained during a three-year European funded Project, namely Think4Jobs. This project exemplifies the significance and benefits of UBC in the design, development and delivery of curricula that meet the evolving demands of the labour market while promoting Critical Thinking (CT) as a foundational 21st century skill to contribute to graduates' employability. Think4Jobs project brought together a multidisciplinary team of researchers and business organisations from five European countries (Germany, Greece, Lithuania, Portugal and Romania) with interests in promoting and developing CT and mitigating eventual competence gaps. The project's success was attributed to key practices, including defining a common conceptualization of CT, employing participatory co-design, and providing common training for university and business partners. Clear objectives, explicit roles, effective communication, and ongoing evaluation further enhanced the collaboration. Experiential learning, real-work problems, and case studies reinforced the curricula, bridging the gap between academia and the labour market. By embracing these insights, future UBC initiatives can empower graduates with the necessary skills to stand out in an ever-changing labour market, contributing to enhanced education and successful careers.

Increasing utilization of secondary raw materials and alternative fuels results in increasing contents of metals in cements. One of elements, the content of which keeps rising in cement is zinc. It comes to cement with secondary raw materials such as slag or fly ash or by the utilization of used tires as an alternative fuel. Zinc ions significantly prolong the hydration process in cement. This work deals with the influence of zinc ions in the form of very poorly soluble ZnO salt and easily soluble ZnCl2 and Zn(NO)3 on the hydration of cement blended with fly ash. Zinc was dosed in the range of 0.05, 0.1, 0.5 a 1% of cement weight. Final products were next analyzed using X-Ray Diffraction.

This study evaluated the effectiveness of an electronic system for managing drug-sensitive pulmonary tuberculosis patients in the Kyrgyz Republic. This was a cohort study using programmatic data. The study included patients registered on the paper-based system in 2019 and the electronic system between June 2021 and May 2022. Data was taken from 302 individuals from the electronic system for completeness and concordance in comparison with the paper-based system. The study showed that for most variables the completeness and concordance was 85.3%-93.0% and was lowest for non-mandatory fields such as medication side effects (26.8% vs 13.6%). No significant difference was observed in time taken from symptom onset to diagnosis and treatment initiation between the two systems. However, the electronic system had a significantly higher percentage of patients who initiated treatment on the same day of diagnosis (80.3% vs. 57.1%). The proportion with successful outcomes was similar in both groups, but the electronic system had a significantly lower proportion of patients with outcomes that were not evaluated or recorded (4.8% vs. 14.3%, p < 0.001). The study highlights the potential advantages of implementing an electronic TB register system for improving records. We advocate for similar studies in other regions in Kyrgyz Republic.

1) Background: The use of linked data in Semantic Web are promising approaches to add value to nutrition research. An ontology, which defines the logical relationships between well-defined taxonomic terms, enables linking and harmonizing research output. To enable the description of domain-specific output in nutritional epidemiology, we propose the Ontology for Nutritional Epidemiology (ONE) according to authoritative guidance for nutritional epidemiologic research; 2) Methods: First, a scoping review was conducted to identify existing ontology terms for reuse in ONE. Second, existing data standards and manuscript reporting guidelines for nutritional epidemiology were converted into ontology, and the terms used in the standards were summarized and listed separately in a taxonomic hierarchy. Third, the ontologies of the nutritional epidemiologic standards, reporting guidelines and the core concepts were gathered in ONE. Three case studies were illustrated for its potential applications. (i) annotation of existing manuscripts and data, (ii) ontology-based inference, and (iii) estimation of reporting completeness in a sample of nine manuscripts; 3) Results: Ontologies for “food and nutrition” (n=33), “disease and special population” (n=86), “data description” (n=21), “research description” (n=32) and “supplementary (meta) data description” (n=44) were reviewed and listed. ONE consists of 339 classes (79 new classes to describe nutrition data and 24 new classes to describe the content of nutrition manuscripts). The case studies demonstrated the application of ONE. 4) Conclusion: ONE is a resource to automate data integration, searching and browsing, and can be used to assess reporting completeness in nutritional epidemiology.

The pulp and paper industry is one of the biggest industry sectors worldwide, whose market growth is expected to reach 370.12 billion USD by 2028. However, as a water-intensive process, the pulp and paper production generate huge volumes of contaminated effluents, some of which contain dissolved high-value chemical compounds, such as lignin, hemicellulose, or carboxylic acids. These compounds can be recovered using membrane operations. Thus, membrane operations represent a method to valorize effluents and byproducts from this industry sector and narrow the gap between biorefinery models and the pulp and paper production as an integrated biorefinery. The present review reviews the state-of-the-art-research and the state-of-the-art applications of membrane operations in the pulp and paper industry.

This paper investigates the application of blended learning in undergraduate translation classes to enhance the effective incorporation of technology in teaching. Blended learning is the combination of face-to-face instruction with online learning, which provides students with a flexible and diverse learning environment for developing technological proficiency. Using a case study methodology, this research examines the translation undergraduate program at the University of Jeddah, which implemented blended learning as its primary instructional framework starting in 2021. The study aims to explore the advantages and challenges associated with the adoption of blended learning in translation classes while offering practical suggestions that could help in its implementation. The findings show several advantages of integrating blended learning into undergraduate translation classes. Firstly, the students could benefit from a flexible learning environment that accommodates their individual learning preferences and schedules. Secondly, It also helps to promote active engagement and interaction which nurture collaborative learning opportunities among students. Thirdly and lastly, blended learning provides a platform for students to develop their technological skills, which become crucial in today's digital age. Despite this, the study also points out significant challenges that need to be addressed. These important challenges include the required planning and preparation involved in creating effective online components, ensuring equitable access to technology and the internet, and adapting teaching and learning approaches to optimise the blended learning experience.To sum up, this paper contributes to the understanding of blended learning in the context of undergraduate translation classes.

SmCo5 constitutes one of the strongest class of permanent magnets, which exhibit enormous uniaxial magnetocrystalline anisotropy energy and have a high Curie temperature. However, the performance of SmCo5 permanent magnets is hindered by a limited energy product and relatively high supply risk. Sm is a moderately expensive element among its group, and Co is a material more expensive than Fe, making SmCo5 magnets the most expensive class of permanent magnets. Subsequently, the need for new materials, with less content in critical and thus expensive resources, is obvious. A promising path of producing new compounds that meet these requirements is the chemically modification of established materials used in PM towards the reduction of expensive resources, for example reducing Co content with transition metals (like Fe, Ni) or using as substitutes raw rare earth materials with abundance greater than their demand, like Ce and La. Important instrument to achieve these goals are theoretical calculations, like Ab-initio methods, and especially DFT based calculations in predicting the possible stable RE-TM intermetallic compounds and their magnetic properties. This review aims to present the progress of recent years in the production of improved SmCo5 type magnets.

This hypothesis demonstrates that the efficiency of Loop-Mediated Isothermal Amplification (LAMP) for nucleic acid detection can be positively influenced by preconcentration of microbial cells onto hydrophobic paper surfaces. The mechanism of this model is based on the high attraction of microbes towards hydrophobic surfaces. Extensive studies have demonstrated that hydrophobic surfaces exhibit enhanced bacterial and fungal adhesion. The preconcentration approach by exploiting this inherent affinity of hydrophobic paper substrates enables the adherence of a greater number of target cells, resulting in a higher concentration of target templates for amplification directly from urine samples. In contrast to conventional methods, which often involve complex procedures, this approach offers a simpler, cost-effective, and user-friendly alternative. Moreover, the integration of cell adhesion, LAMP amplification, and signal readout within paper origami-based devices can provide a portable, robust, and highly efficient platform for rapid nucleic acid detection. This innovative hypothesis holds significant potential for point-of-care (POC) diagnostics and field surveillance applications. Further research and development in this field will advance the implementation of this technology, contributing to improved healthcare systems and public health outcomes.

Three edible aquatic weeds, helencha (Enhydra fluctuans), malancha (Alternanthera philoxeroides), and kalmi (Ipomoea aquatica), were used to produce edible paper sheets. The composition of the raw and paper sheet samples was analyzed, including proximate composition, amino acid content, minerals and heavy metal contents, and bioactive compounds. The dried raw and paper sheets showed similar proximate composition, with carbohydrates being the highest (50.38-64.63%), followed by crude protein (15.25-19.13%), ash (9.30-15.88%), and lipid (1.549-3.43%). The weeds and paper sheets were rich in essential minerals like Na, Ca, Zn, and Fe. Acceptable levels of heavy metals, including Ni, Pb, and Cu, were found. The paper sheets contained seven essential and eight non-essential amino acids. A. philoxeroides sheets showed the highest amino acid content (16146.81mg/100g), while I. aquatica showed the lowest (13118.67 mg/100g). The aquatic weeds paper sheets were rich in containing bioactive compounds and the number in E. fluctuans, A. philoxeroides, and I. aquatica paper sheets were 31, 33, and 40, respectively. There were no significant changes in the nutritional content of aquatic weeds in paper sheet form compared to the raw weeds which suggests promising prospects for the production and consumption as a source of nutrition and bioactive compounds.

This paper aimed to assess climate-smart agricultural practices in Ethiopia, discuss the contribution of climate-smart agricultural practices for mitigation of greenhouse gas emissions, and examine determinant factors of climate-smart agricultural practices in mitigation of greenhouse gas emissions. Conservation agriculture, integrated soil fertility management, agroforestry, crop diversification, and improved livestock feed and feeding practices are among the best climate-smart agricultural practices in Ethiopia. Combination of the adoption of climate-smart agricultural practices such as no-tillage increased crop diversity and retaining crop residue on-farm have a mitigation potential of increased SOC in non-flooded crops that change in a significant ton of CO2e ha-1 year-1. In addition, a mitigation potential of CH4 in reduced irrigation of paddy rice farms was also changed in ton CO2e ha-1 year-1. It was found that productivity enhancing interventions in the tropics could reduce emission intensity in dairy systems by up to 0.9 t CO2e per milk. Agroforestry practices and the addition of organic fertilizers on the farm increased mitigation potential of 784093 t CO2e and 193050 t CO2e biomass of carbon and SOC per year respectively. Adoptions of climate-smart agricultural practices are affected by different factors such as farming factors, technology inaccessibility, environmental factors, policy design and social expertise, negative attitudes and motivations of farmers, farmers’ socio-demographic factors, and farmers' socioeconomic factors. To reverse the situation, preparation of targeted climate-smart agricultural practices to areas that are likely to provide the greatest GHG reduction potential and demonstration of these practices to other areas should be encouraged so that other farmers will learn for similar agro-ecologies.

Paper-based microfluidic analysis devices (μPADs) have attracted attention as a cost-effective platform for point-of-care testing (POCT), food safety, and environmental monitoring. Recently, three-dimensional (3D)-μPADs have been developed to improve the performance of μPADs. For accurate diagnosis of diseases, however, 3D-μPADs need to be developed to simultaneously detect multiple biomarkers. Here, we report a 3D-μPADs platform for the detection of multiple biomarkers that can be analyzed and diagnosed with a smartphone. The 3D-μPADs were fabricated using a 3D digital light processing printer and consisted of a sample reservoir (300 µL) connected to 24 detection zones (of 4 mm in diameter) through 8 microchannels (of 2 mm in width). With the smartphone application, eight different biomarkers related to various diseases were detectable in concentrations ranging from normal to abnormal conditions: glucose (0–20 mmol/L), cholesterol (0–10 mmol/L), albumin (0–7 g/dL), alkaline phosphatase (0–800 U/L), creatinine (0–500 µmol/L), aspartate aminotransferase (0–800 U/L), alanine aminotransferase (0–1000 U/L), and urea nitrogen (0–7.2 mmol/L). These results suggest that 3D-µPADs can be used as a POCT platform for simultaneous detection of multiple biomarkers.

Laser-induced breakdown spectroscopy (LIBS) is an important analysis technique with applications in many industrial branches and fields of scientific research. Nowadays, the advantages of LIBS are impaired by the main drawback in the analysis of collected data. This procedure is essentially based on the comparison of lines present in the spectrum with a literature database. This paper proposes the use of various computational intelligence methods to develop a reliable and fast classification of non-destructively acquired LIBS spectra into a set of predefined classes. We focus on a specific problem of classification of paper-ink samples into 30 separate, predefined classes. For each of 30 classes (10 pens of each of 5 ink types combined with 10 sheets of 5 paper types plus empty pages) 100 LIBS spectra are collected. Four variants of preprocessing, seven classifiers (Decision trees, Random forest, k-Nearest Neighbour, Support Vector Machine, Probabilistic Neural Network, Multi-Layer Perceptron, and Generalized Regression Neural Network), 5-fold stratified cross-validation and test on an independent set (for methods evaluation) scenarios are employed. Our developed system yielded an accuracy of 99.08% with average classification time of about 0.12 s is obtained using the random forest classifier. Our results clearly demonstrates that machine learning methods can be used to identify the paper-ink samples based on LIBS reliably at a faster rate.

The blended perfluorinated sulfonic acid ionomers are prepared to have equivalent weight (EW) ~1000, 980, and 830. The catalyst layers (CLs) using blended PFSA ionomers with different side chain lengths and EWs are investigated, compared to the CLs utilizing single ionomers. The IEC results indicate that the blended ionomers have the targeted EWs. As a result, it is found that the blended ionomers exhibit higher ion conductivity than the single ionomers at all temperatures due to higher water uptake of the blended ionomers. Even though they have a similar EW, it implies that the blended ionomers have bulk structure to form competent free volume. The blended ionomers with short side chain (SSC) and low EW can help reduce the activation energy due to the enhanced hydrophobic and hydrophilic segregation. In addition, it is observed that the catalyst layers using the blended ionomer form more porous microstructure to help reduce the resistance of oxygen transport and attributes to lower mass transfer loss. This effect is significantly revealed in the fuel cell operation at not the lower temperature (70 °C) and full humidification (100%) but the elevated temperature (80 °C) and lower relative humidity (50 and 75%). The blended ionomer-based catalyst layers with higher water uptake and porous CL structure result in higher fuel cell performance and better mass transport than the single ionomer-based catalyst layers.

This study was carried out in three phases. During the first stage, the physicochemical properties of French sauce prepared from different blends of soybean and olive oils were evaluated. In the second stage, the oxidative stability of the optimum sauce sample from the first stage enriched with various amounts of olive leaf polyphenolic extract (OLE) (obtained via ultrasound-assisted extraction) was investigated over 90 days of storage. During the third stage, the microbiological and sensory properties of the samples containing the optimum amounts of OLE, as a substitution for the synthetic preservatives, were studied. According to the results, addition of olive oil at higher levels (75 and 100%) could affect the physicochemical properties of the sauce as compared to the control sample. It was also found that the addition of olive oil (up to 50%) would not significantly impact the sauce properties. Regarding the OLE enrichment in the samples, it was found that high levels of OLE could improve the oxidative stability of the samples. Based on the results of the experiments in the third phase, it was found that OLE could be used as a preservative instead of the commercial ones. Overall, this study suggests the potential use of olive oil and olive leaf extract in the preparation of French sauce to boost its nutritional value and its stability.

In this paper, MnO2 nanowire (MnO2-NW) modified carbon paper (CP) electrode was developed as a novel electrochemical sensor for sensitive determination of tetrabromobisphenol A (TBBPA). MnO2 nanowire was prepared by a hydrothermal synthesis method, and the morphology and structure of MnO2 were characterized using scanning electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. Electrochemical performance of TBBPA on MnO2-NW/CP was investigated by cyclic voltammetry, and the result confirmed that MnO2-NW/CP exhibited excellent sensitive for the determination of TBBPA due to the high specific surface area and good electrical conductivity of the nanowire-like MnO2. Moreover, the important electrochemical factors such as pH value, incubation time and modified material proportion were systematically studied to improve the determination sensitivity. The interferences from similar structure compounds on TBBPA have also been investigated. Under the optimal conditions, MnO2-NW/CP displayed the linear range of 70 500 nM for TBBPA with the detection limit of 3.1 nM, which was superior to some electrochemical methods in references. The work presents a novel and simple method for the determination of TBBPA.

Paper is one of the most promising materials for food packaging and wrapping due to its low environmental impact, but surface treatments are often needed to improve some performance, e.g. the resistance to fats and oils. In this context, this research is focused on the formulation of a new paper bio-coating. Paper was coated with liquids containing Poly(hexano-6-lactone) (PCL), Glycerol and variable percentages of starch (5 - 10% w/w PCL dry weight), agar agar (0 - 1.5% w/w PCL dry weight) and PEG (5% or 15% w/w PCL dry weight) to improve coating uniformity and diffusion. A Design of Experiments approach was implemented to find statistically reliable results in terms of best coating formulation. Coated paper was characterized through mechanical and physical properties. Results showed that agar content (1.5% w/w PCL dry weight) has a beneficial effect on increasing the resistance to oil. Furthermore, the best coating composition has been calculated, and it is: 10% w/w PCL dry weight of Starch, 1.5% w/w PCL dry weight of agar and 15% w/w PCL dry weight of PEG.

The chiral recognition of enantiomers is a topic of great importance. In this study, a straightforward and effective chiral detection strategy was developed for distinguishing between tryptophan (TRP) enantiomers. The approach involved the preparation of a magnetic molecularly imprinted chitosan (MMIC) for the sample preparation, which was combined with a nitrocellulose membrane (paper-based analytical device, PAD) integrated with D-TRP covalently-grafted polymethacrylic acid (PAD_PMA_D-TRP). The discrimination between TRP enantiomers was achieved using AuNPs as a colorimetric probe. Indeed, the presence of D-TRP rapidly induced the aggregation of AuNPs due to its strong affinity to PAD-PMA_D-TRP, resulting in a noticeable color change of the AuNPs from red to purple. On the other hand, L-TRP did not induce any color change. The chiral analysis could be easily performed with the naked eye and/or a smartphone. The developed method exhibited a detection limit of 3.3 µM and it was successfully applied to detect D-TRP in serum samples, demonstrating good recovery rates. The proposed procedure is characterized by its simplicity, cost-effectiveness, rapidity, and ease of operation.

Today project management in every field of life is prerequisite for the success of project by increasing quality reduces cost and schedule. But selecting tools and techniques to achieve our objectives and implement our plan fully is very difficult task because choice creates complexity. So, we discuss AHP to make decision simple. Ranking critical success factor, cloud computing services, risk prioritization, selection of right ETL software and many other systems AHP plays its important role. For the improvement of today’s complex systems it is very important to prioritize and select projects to remove the root cause of the problem. To attain the right selection of construction equipment for carrying out schedule tasks with high efficiency, production and financial capability is the main purpose of procurement of construction equipment process. Certain conflicts can occur due to the construction of UML models in a collaborative way. AHP is used to remove these conflicts and for establishing and evaluating modelers judgments. Nowadays it is very important and critical decision to choose the best option from multiple alternatives for a successful career after passing 12th standard and also it affects our future. “AHP and TOPSIS” methods are used for this purpose. In this paper, an “AHP and Fuzzy AHP” based hierarchical trust model has been used to rate the service providers and their various plans for infrastructure as a service.

This paper develops a novel dynamic correction method for the reliability assessment of large oil-immersed power transformers. First, with the transformer oil-paper insulation system (TOPIS) as the target of evaluation and the winding hot spot temperature (HST) as the core point, an HST-based static ageing failure model is built according to the Weibull distribution and Arrhenius reaction law, in order to describe the transformer ageing process and calculate the winding HST for obtaining the failure rate and life expectancy of TOPIS. A grey target theory based dynamic correction model is then developed, combined with the data of Dissolved Gas Analysis (DGA) in power transformer oil, in order to dynamically modify the life expectancy calculated by the built static model, such that the corresponding relationship between the state grade and life expectancy correction coefficient of TOPIS can be built. Furthermore, the life expectancy loss recovery factor is introduced to correct the life expectancy of TOPIS again. Lastly, a practical case study of an operating transformer has been undertaken, in which the failure rate curve after introducing dynamic corrections can be obtained for the reliability assessment of this transformer. The curve shows a better ability of tracking the actual reliability level of transformer, thus verifying the validity of the proposed method and providing a new way for transformer reliability assessment. This contribution presents a novel model for the reliability assessment of TOPIS, in which the DGA data, as a source of information for the dynamic correction, is processed based on the grey target theory, thus the internal faults of power transformer can be diagnosed accurately as well as its life expectancy updated in time, ensuring that the dynamic assessment values can commendably track and reflect the actual operation state of the power transformers.

Synthesis of styrene butadiene hybrid latex was performed via emulsion polymerization technique using various amount of laponite clay as filler. Laponite clay was modified with cationic surfactant methyl triphenylphosphonium bromide (MTPB) with ion exchange technique prior to polymerization process. The main objective of the modification is to render the surface of the clay layers to more organophilic. Emulsion polymerization was performed under semi batch process using 2 L laboratory stainless steel reactor with temperature 85°C to 90°C for 8 hours. Polymer hybrid styrene butadiene latex was characterized for its physical and chemical properties with standard ASTM Methods. Characterization of its binding and printing properties were carried out with standard testing method (TAPPI Methods) using single coating formulation on 80 gsm woodfree paper. Polymer hybrid latex based on styrene and butadiene monomers with laponite clay enhanced binding and printing properties of coated paper, addition of laponite clay to 6.0 wt % increased the binding resistance of the coated paper two times higher than pure latex. Reducing binder level become possible for cost saving.

PitNETs, although typically benign, comprise a small percentage of therapy-resistant aggressive, occasionally metastatic tumors, underpinning a need to identify novel therapeutic targets. PitNETs carry few mutations but associate with conditions that promote alternative splicing as an oncogenic alternative and express the TrkA neurotrophin receptor, which exhibits oncogenic alternative TrkAIII splicing in other tumors. Alternative TrkAIII splicing was assessed by RT-PCR in 53 PitNETs and compared to HIF1a, HIF2a, SF3B1, SRSF2, U2AF1 and JCPyV large T antigen mRNA expression, unconventional Xbp1 splicing, SF3B1 mutation, and TrkA isoform(s) immunoreactivity by confocal immunofluorescence (IF). Alternative TrkAIII mRNA splicing was detected in all invasive PitNET phenotypes, was significantly elevated in invasive compared to non-invasive PIT1 PitNETs, relatively high in invasive and non-invasive SF1 and TPIT PitNETs, and was associated with IF consistent with intracellular TrkAIII activation but not with hotspot SF3B1 mutations, altered SF3B1, SRSF2 and U2AF1 splice factor mRNA expression, JCPyV large T antigen expression or unconventional Xbp1 splicing. A potential role for hypoxia in TrkAIII mRNA splicing was supported by significant elevation of HIF2a mRNA expression in invasive PIT1 PitNETs. These data demonstrate that alternative TrkAIII splicing, potentially promoted by hypoxia, occurs frequently in PitNETs and may associate with IF consistent with intracellular TrkAIII activation, supporting a potential role for TrkAIII in PitNET pathogenesis and progression, identifying TrkAIII as a novel potential target in refractory PitNETs.

In this study, the objective is to analyze the economic viability of municipal household solid waste (organic matter + paper) for the production of gas, coke and biofuel through the pyrolysis and distillation process. The waste was collected in the city of Belém do Pará-Brazil and pre-treated at UFPA. The analyzed fraction (organic matter + paper) was subjected to pre-treatment of drying, crushing, sieving and was subsequently subjected to proximate characterization and finally pyrolysis of the organic fraction (organic matter + paper) in a fixed bed reactor. Initially, it was necessary to review the literature and with the yields obtained by pyrolysis of the frac-tion, economic feasibility analyzes were carried out. The economic indicators for evaluating the most viable pyrolysis process were: simple payback, discounted payback, net present value (NPV), internal rate of return (IRR), and profitability index (IL). The analysis of the indicators showed the economic viability considering an analysis horizon of 10 years, of materials based on organic material and paper. The break-even point obtained was 0.96 US$/L and the minimum biofuel sales price (MFSP – “Minimum Fuel Sale Price”) obtained in this work was 1.30 US$/L. The sensitivity analysis demonstrated that material costs (organic matter + paper), bio-oil yield, total project investment and electricity, respectively, are the variables that most affect the mini-mum biofuel sales price (MFSP).

In this study, effluent water was produced through Submerged Membrane Bio-Reactor (SMBR) process, which is a simple system and decomposes organic matter contained in wastewater with biological treatment process and performs solid-liquid separation, Especially, ozone oxidation treatment process is applied to effluent water containing fluorescent whitening agent, which is a trace pollutant which is not removed by biological treatment, and influences the quality of reused water. The concentration of COD in the SMBR was 449.3 mg/ℓ-COD, and the concentration of permeate water was 100.3 mg/ℓ-COD. The removal efficiency was about 70.1%. The amount of ozone re- quired for the removal of the fluorescent whitening agent in the permeated water in SMBR was 6.67 g-O3/min, and the amount of ozone required to remove COD relative to the permeate water was calculated to remove 0.997 mg-COD for 1 mg of O3.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p < 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.