The aerospace industry has made extensive use of titanium alloy material due to its exceptional qualities, which include high strength, low weight, and resistance to corrosion. However, these qualities also pose challenges for the material's processing. This paper examines the Ti6Al4V milling endmills coating. First, an analysis is done on the solubility of Ti and Si elements. It is discovered that W and Co elements are far more soluble in Ti than Si and Zr elements, which can effectively stop element diffusion. Next, the base's composition was planned. It was discovered that when the amount of Al increased, the base's surface roughness increased while its hardness and elastic modulus decreased. The binding force between the substrate and the base was greater at 50: 50 Ti:Al ratio. TiSiN and TiSiN/ZrN functional layer properties are examined. When Zr is added to TiSiN/ZrN coating, it improves the coating's hardness and elastic modulus, increases density, and decreases surface roughness and friction coefficient when compared to TiSiN coating. Lastly, an analysis of the initial and intermediate tool wear was done using the Ti6Al4V milling experiment. It was discovered that adding Zr element could successfully extend the tool's cutting life by preventing adhesive wear.

Familial Alzheimer’s disease (FAD) can be caused by mutations in PSEN1 that encodes presenilin-1, a component of the gamma-secretase complex that cleaves amyloid precursor protein. Alterations in calcium (Ca2+) homeostasis and glutamate signaling are implicated in the pathogenesis of FAD, however it has been difficult to assess in humans whether or not these phenotypes are the result of amyloid or tau pathology. This study aimed to assess early calcium and glutamate phenotypes of FAD by measuring the Ca2+ response of induced pluripotent stem cell (iPSC)-derived neurons bearing PSEN1 mutations to glutamate and the ionotropic glutamate receptor agonists NMDA, AMPA and kainate compared to isogenic control and healthy lines. The data shows that in early neurons, even in the absence of amyloid and tau phenotypes, FAD neurons exhibit increased Ca2+ responses to glutamate and AMPA, but not NMDA or kainate. Together this suggests that PSEN1 mutations alter Ca2+ and glutamate signaling as an early phenotype of FAD.

The idealized rhombohedral unit cell of boron carbide is formed by a 12-atom icosahedron and a 3-atom linear chain. Phase transitions are second order and caused by the exchange of B and C sites or by vacancies in the structure. Nevertheless, the impact of such minimal structural changes on the properties can be significant. As the X-ray scattering cross sections of B and C atoms are very similar, the capability of X-ray fine structure investigation is restricted. Phonon spectroscopy helps closing this gap. Phase transitions known to date have been identified due to significant changes of properties: (1) The phase transition near the chemical composition B8C by clear change of the electronic structure; (2) The endothermic temperature-dependent phase transition at 712 K by the according change of specific heat; (3) The high-pressure phase transition at 33.2 GPa by the drastic change of optical appearance from opacity to transparency. These phase transitions affect IR- and Raman-active phonons and other solid-state properties. The phase transitions at B~8C and 712 K mean that a well-defined distorted structure is converted into another one each. In the high-pressure phase transition, an apparently well-defined distorted structure changes into a highly ordered one. In all these cases, the distribution of polar C atoms in the icosahedra plays a crucial role.

The aluminum alloys are prominently employed in the automotive, defense and aerospace industries owing to their excellent properties as compared to that of other metals and alloys. The present work has been centered on the synthesis and the evaluation of mechanical properties of cast and heat treated Al7475-Zirconium carbide composites. The composites were prepared by stir casting method. In order to enhance the properties, Al7475 alloy and Al7475-Zirconium carbide composite were subjected to a T6 heat treatment. The microstructural analysis and tensile, compression, impact and hardness tests were performed on the as-cast as well as T6 heat treated composite specimens. The microstructure of as-cast and heat treated Al7475-Zirconium carbide composite has revealed that the matrix of Al7475 alloy consisted of uniformly dispersed Zirconium carbide particles. The scanning electron microscopy image of heat-treated composite showed a decrease in grain size due to heat treatment effect, resulting in an increase in the strength of the composite. The mechanical properties of heat-treated Al7475-Zirconium carbide composite are superior compared to the as-cast composite. The ultimate tensile strength, yield strength, compression strength, impact strength and hardness of heat treated composite are 16.8%, 15.5%, 18.7%, 18.75% & 22.3% respectively higher than that of as-cast composite.

The key question for the understanding of corrosion phenomena of Si3N4-SiC material in Al reduction cell – whether corrosion by gases (and oxidation in particular) opens way for the corrosion by molten cryolite, or corrosion of Si3N4-SiC by cryolite plays its own role in degradation of the material in service. More probably the reactions of silicon carbide and silicon nitride with molten cryolite go after the stage of pre oxidation to silicon dioxide. The corrosion of Si3N4-SiC material in the reduction cell may take place by “gas-solid” reaction and by “liquid-solid” reaction. There are several variants of lab corrosion test for the evaluation of corrosion resistance of Si3N4-SiC material to cryolite. The results of investigation of Si3N4-SiC lab corrosion test give no direct evidence of selective dissolution of specific phase (Si3N4 or SiC, α-Si3N4 or β-Si3N4) in cryolite. The existing variants of lab corrosion testing require clarification.

One way to reduce the negative impact of human activity on the natural environment is to use natural, easily available and relatively cheap to produce compounds in industrial processes. One such compound is naturally occurring calcium carbonate (CaCO3). This compound has adsorption properties so that it can be an alternative to commonly used adsorbents. The aim of this work is to determine the possibility of using CaCO3 to remove pharmaceutical substances such as sulfadiazine and tetracycline from water. The CaCO3 used in this work was synthesised using our own method, which allows the production of CaCO3 particles with nanometric size. In the conducted research, calcium carbonate was used in the form of a suspension in purified solutions and as an inorganic filling of the developed membranes. The mass of pharmaceutical substances removed from their aqueous solutions was determined in the tests carried out. Based on the results obtained, it can be concluded that CaCO3 has the ability to adsorb both tetracycline and sulfadiazine. In suspension tests, the mass of the removed substances per unit mass of adsorbent was 1.52 mg/g and 6.85 mg/g, respectively. In turn, in the case of the process using the developed membranes, the mass of the removed substances per unit mass of adsorbent was 232 mg/m2 and 524 mg/g, which is a several times greater increase in the mass of the removed substance compared to the process using an unmodified membrane.

We aimed to evaluate the association between daily dietary calcium intake and the risk of cardiovascular disease (CVD) in postmenopausal women using data from the Korean National Health and Nutrition Examination Survey (KNHANES). This cross-sectional study included 12,348 women aged 45–70 years who had reached natural menopause. They were classified into three groups according to daily dietary calcium intake: < 400 mg, 400–800 mg, and >800 mg. The risks of CVD, stroke, angina, and myocardial infarction were assessed in each group. Further, we performed subgroup analysis according to the post-menopause duration (≤10 vs. >10 postmenopausal years). We performed logistic regression analysis with adjustment for age, menopausal age, income, urban area, education, insulin use, body mass index, hypertension, diabetes mellitus, dyslipidemia, high alcohol intake, smoking, exercise, oral contraceptive use, and hormonal therapy use. Calcium intake level was not significantly associated with the risk of CVD in the total population and the ≤10 postmenopausal years subgroup. However, in the >10 postmenopausal years subgroup, daily calcium intake >800 mg was associated with significantly decreased risks of all CVD (odds ratio [OR], 0.27; 95% confidence interval [CI], 0.11–0.64), stroke (OR, 0.06; 95% CI, 0.01–0.42), and myocardial infarction (OR, 0.27; 95% CI, 0.11–0.64). Our findings suggest that a dietary calcium intake of >800 mg/day decreases the risk of CVD events in women who have been menopausal for >10 years.

Aluminium matrix composite’s overall quality is impacted by the friction stir process parameters, which have a major impact on the microstructure, soundness, and particle dispersion inside the stir zone. Although it requires a lot of experimentation, optimizing these factors is vital. For the purpose of optimizing the ultimate tensile strength and microhardness of the AA5083/Silicon carbide and AA5083/Coal composites fabricated by FSP, this work used the Taguchi L9 design of experiments. Three process parameters were investigated at three levels each. For the AA5083/Silicon carbide composite, the results of the ANOVA analysis showed rotational speed has a larger impact on ultimate tensile strength while forAA5083/coal tilt angle has a larger impact on ultimate tensile strength. On the other hand, rotating speed had a greater effect on microhardness and percentage elongation of the AA5083/Coal and AA5083/Silicon carbide composite joints, according to ANOVA analysis. The need for specific process optimization for each composite was highlighted by the fact that different combinations of parameters were best for obtaining the necessary attributes in the AA5083/Silicon carbide and AA5083/Coal composites.

The properties of coatings obtained using two surface preparation methods were compared: heating and etching by ion bombardment with plasma generation by arc evaporators and heating and etching by a glow discharge. A Ti-TiN-(Ti,Cr,Al)N coating was deposited. The use of a glow discharge provides better resistance of the coating to destruction during the scratch test and wear resistance of metal-cutting tools when turning steel. As the cutting speed increases, the advantage in wear resistance of the coating deposited using a glow discharge increases. During the process of heating and etching by ion bombardment with metal ions, a nanolayer rich in cobalt and tooling elements (iron, molybdenum) is formed in the area of the interface of the coating and the carbide substrate. When heated and etched by a glow discharge, such a layer does not form. When using both methods, there is identical diffusion of tungsten into the coating and diffusion of chromium and possibly titanium into the substrate. Thus, the glow discharge heating and etching method can be effectively used in the process of PVD coating deposition.

Arylmagnesium and -calcium reagents are easily accessible, however, ether degradation processes limit the storability especially of the calcium-based heavy Grignard reagents. Ortho-bound substituents with phosphanyl donor sites usually block available coordination sites and stabilize such complexes. The reaction of bromo-2,6-bis(diphenylphosphanylmethyl)benzene (1a) with magnesium in tetrahydrofuran yields [Mg{C₆H₃-2,6-(CH₂PPh₂)₂}₂] (2) after recrystallization from 1,2-dimethoxyethane. However, the similarly performed reduction of bromo- (1a) and iodo-2,6-bis(diphenylphosphanylmethyl)benzene (1b) with calcium leads to ether cleavage and subsequent degradation products. α-Deprotonation of THF yields 1,3-bis(diphenylphosphanylmethyl)benzene. Furthermore, the insoluble THF adducts of dimeric calcium diphenylphosphinate halides, [(thf)₃Ca(X)(µ-O₂PPh₂)]₂ [X = Br (3a), I (3b)], precipitate verifying ether decomposition and cleavage of P-C bonds. Ether adducts of calcium halides [such as [(dme)₂(thf)CaBr₂] (4)] form supporting the initial Grignard reaction and a subsequent Schlenk-type dismutation reaction.

Reducing the hardness of hard water is of great concern nowadays due to some adverse effects on water pipes, boilers and soap consumption. Using the method of biomineralization to precipitate calcium and magnesium ions to become carbonate minerals was one of the most important innovations for reducing the hardness of hard water. The present study sought to explore the physical and chemical conditions of carbonates bio-precipitation and the potential use of Bacillus licheniformis SRB2 strain (GenBank: KM884945.1) isolated from sludge sample of Moshui River (Shandong University of Science and Technology, Qingdao, China) in reducing the hardness of hard waters by the induction of carbonate minerals. In this study, B. licheniformis SRB2 strain was identified based on the morphological, biochemical and 16S rDNA gene sequence homology analysis. The carbonate minerals induced by B. licheniformis bacteria in the liquid culture medium with 3% NaCl and Mg/Ca molar ratio of 0, 6, 8, 10 and 12 were investigated. The culture medium was inoculated with the bacterial liquid seed was set as the experimental group and the other culture medium was inoculated with the same volume of distilled water was set as the control group. The mineral phases, micromorphologies, and crystal structures were analyzed using X-ray powder diffraction, scanning electron microscope, energy dispersive X-ray detector, high resolution transmission electron microscopy and selected area electron diffraction. The bacterial concentrations and pH values of the solution were measured by a spectrophotometer and a pH meter, respectively. The urease secreted by B. licheniformis SRB2 was found to greatly increase the pH values of the liquid medium, which favored the formation of calcium carbonate.As a result, Mg²⁺ and Ca²⁺ ion concentrations decreased greatly due to the biomineralization of calcium carbonate and nesquehonite minerals in the presence of B. licheniformis SRB2 bacterium. There were only few calcium carbonates and no nesquehonite minerals in the control groups. It was also found that the minerals of nesquehonite induced by B. licheniformis SRB2 had a phenomenon of preferred orientation. What was more, even though Mg²⁺ ions inhibited the precipitation of Ca²⁺ ions, but under the action of B. licheniformis SRB2 bacteria, the inhibition effect was significantly declined. The bio-precipitation of calcium carbonate and nesquehonite minerals may represent a new method of pretreatment for the hardness reduction of hard water. The accomplished study is of certain interest for interpretation of the carbonates biomineralization in natural environment, and maybe also has a certain application value in the former processing of hard water

With an increase in energy consumption globally, Fischer-Tropsch (FT) synthesis is a good alternative for producing fuels and chemicals from coal, natural gas or biomass. Among them, coal to liquids has been put into production in countries that have large coal reserves. In this process, Fe-based catalysts are commonly used due to their earth abundance, comparatively wide operation range and ready availability to handle low H2/CO ratio from coal. Despite their extensive applications, the kinetic and mechanistic understandings of Fe carburization and FT reaction on Fe-carbides are relatively limited due to the complexity of phase composition of the applied catalysts. This review summarizes the current state of knowledge of FT synthesis on Fe-carbide with an emphasis on underlying mechanism. Specifically, the employment of model catalyst, such as Raney-Fe, could provide a convenient way to furnish kinetic information regarding Fe carburization and subsequent FT reaction. A major challenge for further understanding catalytic reactions occurring at the Fe-carbide surface is correlating FT activity and selectivity to specific active site. To address this issue, the advancements of both DFT calculations and surface science techniques are highly demanded.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

Presynaptic Ca²⁺-influx through voltage-gated Ca²⁺ channels (VGCC) is a key signal for synaptic vesicle release. Synaptic neurexins can partially determine the strength of transmission by regulating VGCCs. However, it is unknown whether neurexins modulate Ca²⁺-influx via all VGCC subtypes similarly. Here, we performed live cell imaging of synaptic boutons from primary hippocampal neurons with a Ca²⁺-indicator. We used the expression of inactive and active Cre recombinase to compare control to conditional knockout neurons lacking either all or selected neurexin variants. We found that reduced total presynaptic Ca²⁺-transients caused by the deletion of all neurexins were primarily due to the reduced contribution of P/Q-type VGCCs. The deletion of neurexin1α alone also reduced the total presynaptic Ca²⁺-influx but increased Ca²⁺-influx via N-type VGCCs. Moreover, we tested whether the decrease of Ca²⁺-influx induced by activation of cannabinoid receptor 1 (CB1-receptor) is modulated by neurexins. Unlike earlier observations emphasizing a role for β-neurexins, we found that the decrease of presynaptic Ca²⁺-transients induced by CB1-receptor activation depended more strongly on the presence of α-neurexins in hippocampal neurons. Together, our results suggest that neurexins have unique roles in the modulation of presynaptic Ca²⁺-influx through VGCC subtypes and that different neurexin variants may affect specific VGCCs.

The present study showcases a series of crystallization experiments using a specially designed double diffusion system to grow crystals belonging to the calcium carbonate-phosphate system. The experimental U-shaped device comprised two vertical solution containers, separated by a horizontal column of silica hydrogel. Each container was filled with 0.5 M CaCl2 and 0.5 M Na2CO3 solutions, which diffused through the gel column over time. Na3PO4 solutions, with 50 and 500 ppm concentrations, were incorporated into the gel in different experiments, resulting in a homogeneous distribution of phosphate concentrations within the diffusion column. After 15 and 30 days incubation period post-nucleation, the crystals formed in different sections of the gel were carefully extracted and studied with scanning electron microscopy and electron microprobe. Additionally, Raman spectra were collected from the samples using a confocal Raman microscope, providing further insights into their molecular composition and structural properties. The obtained results show that under the induced experimental conditions (i) phosphate incorporates into calcite´s structure, and (ii) the growth of calcium phosphates in the presence of carbonate ions involves the sequential, heterogeneous nucleation of CO3-bearing OCP/HAP-like phases with Raman spectral characteristics very similar to those of bioapatites.

The calcium-sensing receptor (CAS), as a chloroplast thylakoid membrane protein, involved in the process of [Ca2+] ext-induced [Ca2+]cyt increase (CICI) in the plant. However, the underlying mechanism regulating this process is lacking. Furthermore, recent evidence suggests that CAS may perform additional roles in the plant. Here, we provide an update covering the multiple roles of CAS in stomatal movement regulation and calcium signaling in the plant. We also analysis the possible phosphorylation mechanism of CAS by light and discuss the role of CAS in abiotic stress (drought, salt stress) and biotic stresses (plant immune signaling). Finally, we provide a perspective for future experiments which are required to fill gaps in our understanding of the biological function of CAS in the plant.

Two methods for Pd nanoparticle synthesis were explored with three different carbide-derived carbon (CDC) support materials of which one was nitrogen-doped. These materials were studied for oxygen reduction reaction (ORR) in 0.1 M KOH solution. The prepared CDC/Pd catalysts were characterized using TEM, XRD and XPS. Using these methods, we can observe the influence of support materials for one-pot synthesis methods as we use the standard citrate method and polyol method with polyvinylpyrrolidone (PVP) as a capping agent. Comparing the two methods N-doping of carbon material resulted in smaller nanoparticles only in the case of citrate synthesis, suggesting that the influence of support is weaker using polyol method. Citrate method on CDC1, which was predominantly microporous led to a higher degree of agglomeration and larger particle formation in comparison to CDC2 and CDC3 supports, which possessed higher degree of mesoporosity. Smaller Pd particle sizes were achieved using citrate and NaBH4 in comparison to the ethylene glycol-PVP method. CDC2 and CDC3 did not show significant difference suggesting that the N-doping did not have much of an influence on the ORR. Highest SA value was observed on CDC1/Pd_Cit, which could be attributed to formation of larger particles and agglomerates.

TiC–high Mn steel-bonded carbide with a cellular structure was designed and fabricated by powder metallurgy techniques using coarse and fine TiC particles as the hard phase. This preparation process was carefully investigated and optimized. The microstructure of the TiC steel-bonded carbide was observed using a scanning electron microscope. Results showed that there are two types of microstructures in the TiC steel-bonded carbide: the coarse-grained TiC and fine-grained TiC. The transverse rupture strength and impact toughness of the alloy reach maximum values 2231 MPa and 12.87 J/cm2, respectively when the starting weight ratio of MP-A (containing coarse TiC particles) to MP-B (containing fine TiC particles) is 60:40. Hence, this study serves as a feasible example of how to prepare a high-strength and high-toughness TiC–high Mn steel-bonded carbide.

Abstract. Graphene family (GF)-Calcium phosphate (CaP) composites, holds great potential as components of bone regeneration materials. GF nanomaterials can be modified physically as well as chemically, which are to be biomimetic, mechanically to be hard due to their capability to support exceptional mechanical, thermal and electronic properties. These biocompatible GF composites coated on the calcium phosphate can enhance and tolerate stem cell growth and differentiation, proliferation into various lineages or interact with bioorganisms. The development in CF-CaP materials and their physicochemical/biointeractions and strategies towards osteoblasts is a great concern to promote faster healing and reconstructions of large bone imperfections or defects. In this review, we explain the influence of the CF-CaP and summarize recent developments on designing CF-CaP architectures as multifunctional bone regeneration platforms. We have also explored the typical biological applications concerning these CF-CaP based bioactive nanocomposites. Furthermore, the future viewpoints and evolving challenges will also be emphasized. Due to the shortage of full-length reviews in this emerging research field, this review would be caught great attention and encourage various new chances across a wider range of disciplines.

This study evaluated the effect of newly introduced calcium silicate-based temporary intracanal medicament Bio-C Temp and calcium hydroxide-based material UltraCal XS on the release of transforming growth factor β1 (TGF-β1) from root canal dentin. Twenty-two intact and fully developed human premolars from patients aged 15 – 18 were shaped and irrigated according to the current clinical recommendations. The teeth were then gently split in half, and the root canal dentin of paired samples was covered with Bio-C Temp or UltraCal XS. After 3 weeks of incubation, the specimens were conditioned with 17% EDTA and the collected solution was subjected to quantification of released TGF-β1 by performing ELISA. One-way analysis of variance (ANOVA), followed by Tukey’s test, was selected to determine the statistically significant differences between the groups at the 0.95 confidence level. The highest mean value of released TGF-β1 (1993.1 pg/ml) was detected in the control group, where root canal dentin was conditioned with 17% EDTA alone. Regarding experimental groups, Bio-C Temp released a statistically significant higher amount of TGF-β1 (282.14 pg/ml) compared to UltraCal XS (114.28 pg/ml; p = 0.0158). Bio-C Temp affected the release of growth factors from root canal dentin less than UltraCal XS and may therefore serve as an intracanal medicament for regenerative endodontic procedures.

Boron carbide (B4C) powders with defined stoichiometry, high crystallinity, minimal impurity content, and a fine particle size are imperative for realizing the exceptional properties of this compound in advanced high-technology applications. Nevertheless, achieving the desired stoi-chiometry and particle size using traditional synthesis methods, which rely on prolonged, high-temperature processes, can be challenging. The primary objective of this study is to syn-thesize fine B4C powders characterized by high crystallinity and a sub-micron particle size, em-ploying a fast, and energy-efficient method. B4C powders are synthesized from elemental boron and carbon in a high-frequency induction heating furnace using the Electromagnetic Induction Synthesis (EMIS) method. The rapid heating rate achieved through contactless heating promotes the ignition and propagation of the exothermic chemical reaction between boron and carbon. Additionally, electromagnetic effects accelerate atomic diffusion, allowing the reaction to be completed in an exceptionally short timeframe. The grain size and crystallinity of B4C can be finely tuned by adjusting various process parameters, including the post-ignition holding temperature and the duration of heating. As a result, fine B4C powders can be synthesized in under 10 minutes. Moreover, these synthesized B4C powders exhibit high resistance to oxidation when exposed to air.

'Cv 'Doña María' table grape is a high-quality table grape variety included in the Protected Designation of Origin (PDO) of the European Union "The bagged grape of the Vinalopó." The PDO stipulates that grape clusters must be protected with paper bags from inclement weather and insects, which helps enhance the final grape quality. However, 'Doña María' is a variety prone to high shattering in the late stages of ripening on the vine and during postharvest. Inorganic calcium treatments are one of the most commonly used tools to reduce this disorder, but the translocation of this mineral from veraison onward has been questioned. In this study, five applications were performed, from veraison to harvest, using sorbitol-chelated calcium (0.7 % + 1.0 %), Ca(NO3)2 (Ca) at 0.7% and sorbitol at 1%. It was observed that bagged grapes (not wetted with the solutions) only increased the concentration of total and bound calcium when treated with Sorbitol-Ca. This resulted in reduced berry drop during cultivation and postharvest and improved fruit firmness. Additionally, it reduced grape metabolism indicators such as respiration rate, weight loss, malic acid degradation, prevented abscisic acid (ABA) and malondialdehyde (MDA) accumulation, and favored the accumulation of secondary metabolites such as total polyphenols, increased antioxidant activity, and sugar content. The application of sorbitol-chelated calcium is an effective and safe tool that enhances fruit quality and prevents losses due to shattering during postharvest.

In recent years, it has been found in engineering practice that the service life of cemented carbide shield machine tools used in uneven soft and hard strata is substantially reduced. The study found that thermal stress is the main reason for the failure of cemented carbide shield tunneling tools when shield tunneling is carried out in uneven soft and hard soil. To maintain the hardness of cemented carbide, improving the thermal conductivity of the shield machine tool is of great importance for prolonging its service life and reducing engineering costs. In this paper, graphene and carbon nanotubes were mixed with WC-Co powder and sintered by SPS (Spark Plasma Sintering). The morphology was observed by using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A Rockwell hardness tester and bending strength tester were used to test hardness, bending strength and thermal conductivity. The results show that adding trace graphene or carbon nanotubes can increase the bending strength of the cemented carbide by approximately 50% while keeping the hardness of the cemented carbide unchanged. The thermal conductivity of the cemented carbide can be increased by 10% with the addition of 0.12% graphene alone.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Powders with phase composition including syngenite K2Ca(SO4)2·H2O and/or calcium sulfate di-hydrate (gypsum) CaSO4·2H2O were synthesized from powder of calcium carbonate CaCO3 and water solutions of potassium hydrosulfate KHSO4 of various (0.5M, 1M and 2M) concentrations. Molar ratio of starting salt KHSO4/CaCO3=2 were used to provide formation of syngenite K2Ca(SO4)2·H2O. But when using 0.5M water solution of potassium hydrosulfate KHSO4 the phase composition of synthesized powder was presented by calcium sulfate dihydrate (gypsum) CaSO4·2H2O. When using 1M and 2M water solution of potassium hydrosulfate KHSO4 the syn-genite K2Ca(SO4)2·H2O was found as predominant phase in synthesized powders. According es-timations made from thermal analysis data when 1.0M and 2.0M water solutions of potassium hydrosulfate KHSO4 were used the content of calcium sulfate dihydrate (gypsum) CaSO4·2H2O in these powders were not higher then as 7.9 and 1.9 % respectively. Phase composition of products isolated from mother liquors via water evaporation consisted of syngenite K2Ca(SO4)2·H2O and potassium sulfate (arcanite) K2SO4. Synthesized powders can be used in preparation of biocom-patible bioresorbable materials with phase composition in the K2O‑CaO‑SO3‑H2O system; as matrix of thermo- or photo-luminescent materials; as components reducing the setting time and increasing strength of sulfate cements; in the fertilizing industry and also as a components of Martian regolith simulant.

Voltage-gated Ca²⁺ (Ca_v) channels play pivotal roles in regulating gene transcription, neuronal excitability, and neurotransmitter release. In order to meet the spatial and temporal demands of visual signaling, Ca_v channels exhibit unusual properties in the retina compared to their counterparts in other areas of the nervous system. Here, we review current concepts regarding the specific subtypes of Ca_v channels expressed in the retina, their intrinsic properties and forms of modulation, and how their dysregulation could lead to retinal disease.

Calcium sulphate (CS) is currently used as a bioabsorbable, completely synthetic and sterile material in the management of infected tissues and dead spaces (DS) mainly resulting from surgical procedures. Residual DS in the postoperative, may create an environment where hematomas fill up and bacteria can proliferate, leading to a high incidence of postoperative infections. Considering the available reviews in the literature, CS has been mainly studied in orthopedic surgery mostly giving brilliant results and low complication rates. Nowadays, orthopedists avail it in the form of pearls both as a bone void filler and as an “off-label” delivery agent for antibiotics in arthroplasty, chronic osteomyelitis and open fractures, paving the way of its application in many other contexts given its natural dis-position to biodegradation. In the last years, CS beads have been gaining ground in the general, vascular and endocrinological surgical specialties. Despite its clear potential and the increasing number of scientific evidences on the safety and effectiveness of CS application in the prophylaxis and treatment of infections, there are not many studies reporting on its application in fields other than orthopedics, with a substantial paucity in plastic and reconstructive surgery literature. This is some-how surprising, since reconstructive surgery often deals with complex wounds secondary to bone and soft tissue exposure, suture dehiscence, trauma, and surgical site infections. As far as we know this is the first updated systematic review assessing the state of the art, indications and new perspectives on the application of CS beads in plastic and reconstructive surgery.

Hypertension is a frequent risk factor for cardiovascular diseases and the prevalence rate is continuously rising. Multiple pathophysiological mechanisms are responsible for hypertension, necessitating a combination of drugs from different classes for best management. Combination therapy is five times more effective in decreasing blood pressure compared to escalating the dose of a single agent. As per the ACCOMPLISH trial analysis, coupling a renin-angiotensin system inhibitor with a calcium channel blocker is more effective than the combination of a renin-angiotensin system inhibitor with diuretics in reducing major cardiovascular events, cardiovascular-related mortality, and the progression of chronic kidney disease. The renin-angiotensin system can be suppressed by inhibiting the angiotensin-converting enzyme or angiotensin type 1 receptor (AT1R), resulting, in decreased vascular smooth muscle contraction, heart performance, and reduced aldosterone synthesis. Calcium channel blockers work by inhibiting L-type calcium channels, reducing heart performance via negative inotropic, chronotropic, and bathmotropic effects, along with reducing vascular smooth muscle contraction. Diuretics exert their antihypertensive impact by changing body fluid volume and electrolytes. Initially, hypertension treatment commences with a single medication but often, different classes of two or more antihypertensive medications are necessary for achieving the target blood pressure goal. Sometimes, for Resistant hypertension four different classes of antihypertensive medications are necessary to reach the target blood pressure goal.

The increasing use of energy resources recovered from the subsurface environments and the resulting carbon imbalance in the environment has motivated the need to develop thermodynamically downhill pathways to convert and store CO₂ as water insoluble calcium or magnesium carbonates. While previous studies extensively explored aqueous routes to produce calcium and magnesium carbonates from CO₂, there has been a limited scientific understanding of the phase evolution and textural changes during the direct gas-solid conversion routes to produce calcium carbonate from calcium hydroxide, which is one of the abundant constituents of alkaline industrial residues. With increasing interest in developing integrated pathways for capturing, converting and storing CO₂ from dilute flue gases, understanding the compositions of the product phases as they evolve is essential for evaluating the efficacy of a given processing route. Therefore, in this study, we investigate the phase evolution and the corresponding textural changes as calcium hydroxide is converted to calcium carbonate under the continuous flow of CO₂ at an ambient pressure of 1 atm and on heating continuously from 30 °C to 500 °C using in-operando wide angle X-ray scattering (WAXS), small angle X-ray scattering (SAXS), and ultra-small angle X-ray scattering (USAXS) measurements.

Ca2+ can boost protein-protein interactions and, if present at an appropriate level, can potentially improve the physicochemical properties of protein gels and films. This study aimed to determine the effect of CaCl2 (0, 0.01 0.025 0.05% w/w) on the optical, water affinity, and mechanical char-acteristics of glycerol (Gly)- and sorbitol (Sor)-plasticized pea protein isolate (PPI) films. The CaCl2 caused darkening and a color shift of the films from yellow to yellow-green. Additionally, de-creased light transmission, particularly in the UV range, and reduced moisture content were observed. The CaCl2 decreased the water vapor permeability (WVP) of the Gly-plasticized film by an average of 20%, with no effect on the Sor-plasticized film. All films were completely soluble in water. The CaCl2 negatively impacted the mechanical integrity of the films, reducing the tensile strength of the Gly- and Sor-plasticized films by ~16% and 14-37%, respectively. Further increases in CaCl2 content (0.1% and 0.2% w/w) led to concentration-dependent cracks, suggesting protein over-crosslinking. In summary, the incorporation of CaCl2 into PPI films did not provide signif-icant benefits and actually worsened key properties such as transparency and mechanical strength. The type of plasticizer influenced how CaCl2 affected some properties of the PPI film.

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

The effects of the additives (silicon carbide and titania) and sintering temperatures on the phases developed, physical and mechanical properties of sintered mullite-carbon ceramic composite produced from kaolin and graphite was investigated. The kaolin and graphite of known mineralogical composition were thoroughly blended with 5 and 3 (vol.) % silicon carbide and titania respectively. From the homogeneous mixture of kaolin, graphite and titania, standard samples were prepared via uniaxial compaction. The test samples produced were subjected to firing (sintering) at 1300˚C, 1400˚C and 1500˚C. The sintered samples were characterized for the developed phases using x‐ray diffractometry analysis, microstructural morphology using ultra‐high resolution field emission scanning electron microscope (UHRFEGSEM). Various physical and mechanical properties were determined. It was observed that the addition of SiC/TiO2 additives to the samples made them to possess very low oxidation indices .This also resulted in improvement in the bulk densities and cold crushing strength of the sample when compared with those without additives. It was concluded that the addition of SiC/TiO2 additives improves on the high temperature oxidation resistance of the mullite-carbon ceramic composite sample.

Ceramic samples based on b-calcium pyrophosphate b-Ca2P2O7 were prepared using firing at 900, 1000, and 1100 oC from powders of g-calcium pyrophosphate g-Ca2P2O7 with preset molar ratios Ca/P=1; 0,975 and 0,95. To prepare powders of g-calcium pyrophosphate g-Ca2P2O7 with preset molar ratio Ca/P=1; 0,975 and 0,95 powder mixtures based on calcium lactate pentahydrate Ca(C3H5O3)2⋅5H2O and, monocalcium phosphate monohydrate Ca(H2PO4)2⋅H2O were treated in an aqua medium in mechanical activation conditions, dried, disaggregated in acetone, and heat-treated at 600 oC. The phase composition of powder mixtures after treatment if planetary mill in aqua medium included both brushite CaHPO4⋅2H2O or monetite CaHPO4, and starting salts. The phase composition of all powder mixtures after disaggregation in acetone in planetary mill included monetite CaHPO4 and starting salts. After heat treatment at 600 oC according to the XRD data phase composition of all powder mixtures was presented by g-calcium pyrophosphate g-Ca2P2O7. The grain size of ceramics increased both with the growth of firing temperature and with decreasing of molar ratio Ca/P of powder mixtures. Calcium polyphosphate (t melt =960–968 oC) formed from monocalcium phosphate monohydrate Ca(H2PO4)2⋅H2O acted like a liquid phase sintering additive. It was confirmed by tests in vitro, that prepared ceramic materials with preset molar ratio Ca/P=1; 0,975 and 0,95 and phase composition presented by b-calcium pyrophosphate b-Ca2P2O7 according to XRD data were biocompatible and could maintain bone cells proliferation.

An amorphous silicon carbide (SiC) membrane with H2 permeance of 1.2E-7 mol･m^-2･s^-1･Pa^-1 and excellent H₂/CO₂ selectivity of 2600 at 673 K was successfully synthesized on a Ni-gamma-alumina-coated alpha-alumina porous support by counter diffusion chemical vapor deposition (CDCVD) using silacycrobutane (SCB) at 788 K. The dominant permeation mechanism for He and H₂ in the temperature range 323-673 K was activated diffusion. The SiC active layer was formed in Ni-gamma-Al₂O₃ intermediate layer. The thermal expansion coefficients mismatch between SiC active layer and Ni-gamma-Al₂O₃-coated alpha-Al₂O₃ porous support was eased by the low decomposition temperature of SiC source and membrane structure.

A useful perioperative nutritional therapy for highly invasive esophageal cancer surgical cases needs to be developed. We clarified the usefulness of amino acid-enriched nutritional therapy using glutamine (Gln)/arginine (Arg)/calcium β-hydroxy-β-methylbutyrate (HMB) products on the short-term postoperative outcomes of minimally invasive esophagectomy for esophageal cancer. Altogether, 114 patients (Gln/Arg/HMB group) received perioperative nutritional therapy with Gln/Arg/HMB products, and we retrospectively investigated the change in nutritional parameters including skeletal muscle mass, occurrence of postoperative complications, and short-term postoperative outcomes in this group. The results were compared between the Gln/Arg/HMB and control groups (79 patients not receiving the Gln/Arg/HMB products). The incidence of all postoperative complications, sputum expectoration disorder, and pleural effusion of grade ≥III was significantly lower in the Gln/Arg/HMB group (62.0% vs. 38.6%, p = 0.001; 44.3% vs. 28.1%, p = 0.020; 27.8% vs. 13.2%, p = 0.011, respectively). The psoas muscle area and postoperative body weight was significantly higher at 1 month and 1 year after surgery in the Gln/Arg/HMB group than in the control group (93.5% vs. 99.9%, p &lt; 0.001; 92.0% vs. 95.4%, p = 0.006). Perioperative amino acid-enriched nutritional therapy may improve the short-term postoperative outcomes, nutritional status, and skeletal muscle mass of esophageal cancer surgical patients.

This work proposes a methodology for the design, development, optimisation, and evaluation of amorphous rosuvastatin calcium tablets (BCS class II drug). The main goal was to ensure rapid disintegration and high dissolution rate of the active ingredient, thus enhancing its bioavailability. The design started from a careful selection of excipients, which due to their characteristics and proportions within the formulation allowed the use of their properties such as fluidity or granulometric distribution. The formulation was characterised using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermogravimetry (TGA), Fourier transform infrared spectroscopy (FT-IR) and powder X-ray diffraction (PXRD) methods. The galenic SeDeM methodology was used to establish the profile of the active ingredient-excipient mixture and guarantee its suitability for producing tablets by the direct compression method. The results demonstrate that the amorphous rosuvastatin calcium tablets formulation developed made it possible to obtain cost-effective tablets by direct compression with optimal pharmacotechnical characteristics that showed a remarkable disintegration and dissolution rate. The manufactured tablets complied with the pharmacopoeia guidelines regarding uniformity of weight, tablet hardness, thickness, friability, in vitro disintegration time and dissolution profile.

36 years after the publication of the important article by Busa and Nuccitelli on the variability of intracellular pH (pH_i) and the interdependence of pH_i and intracellular Ca²⁺ concentration ([Ca²⁺]_i), little research has been carried out on pH_i and calcium signaling. Moreover, the results appear to be contradictory. Some authors claim that the increase in [Ca²⁺]_i is due to a reduction in pH_i, others that it is caused by an increase in pH_i. The reasons for these conflicting results have not yet been discussed and clarified in an exhaustive manner. Variations in pH_i have a significant impact on the increase in [Ca²⁺]_i and hence on some of the basic biochemical mechanisms of calcium signaling. This paper focuses on the possible triggering role of protons, highlighting the mechanisms potentially involved and the open issues that could be clarified by research.

Background: Previous papers have developed a statistical mechanics of neocortical interactions (SMNI) fit to short-term memory and EEG data. Adaptive Simulated Annealing (ASA) has been developed to perform fits to such nonlinear stochastic systems. An N-dimensional path-integral algorithm for quantum systems, qPATHINT, has been developed from classical PATHINT. Both fold short-time propagators (distributions or wave functions) over long times. Previous papers applied qPATHINT to two systems, in neocortical interactions and financial options. Objective: In this paper the quantum path-integral for Calcium ions is used to derive a closed-form analytic solution at arbitrary time that is used to calculate interactions with classical-physics SMNI interactions among scales. Using fits of this SMNI model to EEG data, including these effects, will help determine if this is a reasonable approach. Method: Methods of mathematical-physics for optimization and for path integrals in classical and quantum spaces are used for this project. Studies using supercomputer resources tested various dimensions for their scaling limits. In this paper the quantum path-integral is used to derive a closed-form analytic solution at arbitrary time that is used to calculate interactions with classical-physics SMNI interactions among scales. Results: The mathematical-physics and computer parts of the study are successful, in that there is modest improvement of cost/objective functions used to fit EEG data using these models. Conclusions: This project points to directions for more detailed calculations using more EEG data and qPATHINT at each time slice to propagate quantum calcium waves, synchronized with PATHINT propagation of classical SMNI.

Nano- and microparticles are increasingly widely used in biomedical research and applications, particularly as specific labels and targeted delivery vehicles. Silica has long been considered the best material for such vehicles, but it has some disadvantages limiting its potential, such as the proneness of silica-based carriers to spontaneous drug release. Calcium carbonate (CaCO3) is an emerging alternative, being easily available, cost-effective, biocompatible material with high porosity and surface reactivity, which makes it an attractive choice for targeted drug delivery. CaCO3 particles are used in this field in the form of either bare CaCO3 microbeads or core/shell microparticles representing polymer-coated CaCO3 cores. In addition, they serve as removable templates for obtaining hollow polymer microcapsules. Each of these types of particles has its specific advantages in terms of biomedical applications. CaCO3 microbeads are primarily used due to their capacity for carrying pharmaceutics, whereas core/shell systems ensure better protection of the drug-loaded core from the environment. Hollow polymer capsules are particularly attractive because they can encapsulate large amounts of pharmaceutical agents and can be so designed as to release their contents in the target site in response to specific stimuli. This review focuses first on the chemistry of the CaCO3 cores, core/shell microbeads, and polymer microcapsules. Then, systems using these structures for the delivery of therapeutic agents, including drugs, proteins, and DNA, are outlined. The results of systematic analysis of available data are presented. They show that the encapsulation of various therapeutic agents in CaCO3-based microbeads or polymer microcapsules is a promising technique of drug delivery, especially in cancer therapy, enhancing drug bioavailability and specific targeting of cancer cells while reducing side effects. To date, research in CaCO3-based microparticles and polymer microcapsules assembled on CaCO3 templates has mainly dealt with their properties in vitro, whereas their in vivo behavior still remains poorly studied. However, an enormous potential of these highly biocompatible carriers for in vivo applications is undoubted. This last issue is addressed in depth in the Conclusion and Outlook sections of the review.

This study focuses on the analyses of nano-twinned Copper (Cu) films deposited through magnetron sputtering on Silicon Carbide (SiC) chips. The investigation encompasses the utilization of Chromium (Cr) adhesive layer coupled with varying voltage bias conditions. The goal is to comprehensively examine the influence of adhesive layer and negative bias voltages, contributing to an enhanced understanding of materials engineering and bonding technologies for advanced applications. The formation of a nanotwinned structure and (111) surface orientation can be properly controlled by applied substrate bias. High density nanotwinned structures were introduced into Cu films sputtered on SiC substrates with 82.3% of (111)-orientation proportion at -150 V much higher than the Cu film sputtered with another substrate bias. It is concluded that the sputtered Cu nanotwinned film formed with -150 V bias voltage has the potential to be employed as the interlayer for low temperature direct bonding.

Context: Persea Americana is reported to have medicinal value. Calcium Carbide (CaC2), a fruit-ripening agent, has been shown to be toxic to body organs. Objective: To determine the effect of avocado seed extract (ASE) on CaC2-induced hepatotoxicity in rats. Methodology: Four experimental groups, each of 5 adult wistar rats were fed respectively with normal diets (group A); 250mg/kg ASE (group B); 100mg/kg CaC2 (group C); combination of 100mg/kg CaC2 and 250mg/kg ASE – group D. Changes in the rats’ behaviours, body weights, and liver function were assessed over 21 days. Data were analyzed using SPSS. The cumulated rat weights, rat liver weights and serum liver enzyme levels for groups B, C, and D rats were compared to group A. Results: Abnormal behavior was most observed in group C rats. Rats in group A showed a significant increase in weight before and three weeks following administration of feeds while rats in groups B, C, and D showed significant decrease in weight – more marked in group C rats. Only the mean liver weights of rats in group C showed significant decrease compared to that in group A, p = 0.001. Similarly, only the cumulated liver enzyme levels of rats in group C demonstrated significant increase when compared to group A rats - indicating hepatotoxicity. Conclusion In this study, hepatotoxicity occurred in CaC2-administered rats. However, the combination of CaC2 and ASE showed no liver toxicity indicating a mitigating effect of ASE to CaC2-induced hepatotoxicity.

The homeostasis of cellular calcium is fundamental for many physiological activities, while calcium levels maintain inhomogeneous within cells. During the onset of asthma, epithelial and inflammatory cells secrete platelet derived growth factor (PDGF), inducing proliferation and migration of airway smooth muscle (ASM) to the epidermal layer, narrowing the airway. The regulation of ASM cells by PDGF is closely related to the conduction of calcium signals. In this work, we generated subcellular-targeted FRET biosensors to investigate calcium regulations at different compartments of ASM cells. PDGF-induced cytoplasmic calcium [Ca2+]C increase was attributed from both extracellular calcium influx and endoplasmic reticulum (ER) calcium [Ca2+]ER release, which was partially regulated by PLC-IP3R pathway. Interestingly, removal of extracellular calcium influx led to inhibited ER calcium release, likely through inhibitory effect on calcium-dependent activation of ER ryanodine receptor. Inhibition of L-type calcium channel on plasma membrane, or SERCA pump on ER resulted in both reduced [Ca2+]C and [Ca2+]ER from PDGF stimulation, while IP3R channel inhibition led to reduced [Ca2+]C only. Inhibited SERCA pump caused immediate [Ca2+]C increase and [Ca2+]ER decrease, indicating an active calcium exchange between cytosol and ER storage in resting cells. PDGF-induced calcium at outer mitochondrial membrane sub-region showed similar regulatory response to cytosolic calcium, not influenced by inhibition of mitochondrial calcium uniporter channel. Therefore, our work identified calcium flow pathways among extracellular medium, cell cytosol, and ER by regulatory calcium channels. Particularly, extracellular calcium flow has an essential function to fully activate ER calcium release.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

In an attempt to correct misunderstandings this article brings together the observations on Calcium, Myosin Binding Protein-C and Hypertrophic Cardiomyopathy in the basic function of cardiac muscle. A finding of many years ago is reiterated in a novel enzyme kinetic format with defined rate limiting step which makes CaATP the apparent substrate of the actomyosin cross-bridge. The relationship of these kinetics to recent observations on disruption of myosin binding protein-C is described along with how this bears on the understanding of the related cardiomyopathies.

Psychiatric disorders are mental, behavioral or emotional disorders. These conditions are prevalent, one in four adults suffer from any type of psychiatric disorders world-wide. It has always been observed that psychiatric disorders have a genetic component, however new methods to sequence full genomes of large cohorts have identified with high precision genetic risk loci for these conditions. Psychiatric disorders include, but are not limited to, bipolar disorder, schizophrenia, autism spectrum disorder, anxiety disorders, major depressive disorder, and attention-deficit and hyperactivity disorder. Several risk loci for psychiatric disorders fall within genes that encode for voltage-gated calcium channels (Ca_Vs). Calcium entering through Ca_Vs is key for multiple neuronal processes. In this review, we will summarize recent findings that link Ca_Vs and their auxiliary subunits to psychiatric disorders. First, we will provide a general overview of Ca_Vs structure, classification, function, expression and pharmacology. Next, we will summarize tools and databases to study risk loci associated with psychiatric disorders. We will examine functional studies of risk variations in Ca_V genes when available. We will review pharmacological evidence of the use of Ca_V modulators to treat psychiatric disorders. Our review will be of interest for those studying pathophysiological aspects of Ca_Vs.

Management of calcium and phosphate in biofluids is key to maintaining physiological mineral homeostasis (i.e., appropriate mineralization of hard tissues and an absence of mineral deposition in soft tissues). This review describes and contrasts the ways vertebrates manage calcium phosphate in two biological fluids (breast milk and serum) and illustrates the benefits of mineral sequestration by proteins. In milk, phosphoprotein-sequestered calcium magnesium phosphates provide nutritional support, whereas in serum, protein-sequestered calcium phosphates control transport and delivery of calcium and phosphate to tissues for biological function or excretion. In addition, subsets of sequestered phosphates in serum have been identified as culprits underlying ectopic deposition of calcium phosphates and toxicity.

Pore Forming Toxins (PFTs), formed mainly by virulence factors of bacteria, belongs to Pore Forming Protein (PFP) family. Secreted as soluble monomers, they bind specific targets in membranes where their oligomerization and insertion place. Lysenin, a member of the PFTs, forms and oligomer after sphingomyelin binding, the so-called prepore, which become inserted forming a pore after a conformational change triggered by a pH decrease. In crowded conditions, oligomers tends to stay in prepore form because the prepore-to-pore transition is sterically blocked. In this study, we investigate the effect of calcium ions in those crowded conditions, finding that calcium act as a trigger for lysenin insertion. We localize the residues responsible for calcium sensitivity in a small α-helix. Our results are not only one of the few complete structural descriptions of prepore-to-pore transitions but the very first that involves a calcium triggering mechanism. The presence of glutamic or aspartic acids in the insertion domains could be an indication that calcium may be a general trigger for PFTs and more generally PFP.

We simulate elementary calcium release events (sparks) in a single calcium release unit in ventricular myocyte. Previously developed and tested electron-conformational model of the stochastic dynamics of RyR-channels is integrated to the calcium dynamics model in the cardiac cell. This approach allows to observe RyRs opening/closing in details on the macromolecular level during the calcium dynamics course. We simulate calcium diffusion in the dyadic space and “domino-like” RyR’s activation during the so-called “calcium induced-calcium release process”. Ca²⁺ sparks initiation, spread and termination are investigated in the computer experiments. Sparks’ initiation and termination rate dependence on the Ca²⁺ diffusion velocity is observed. We show that sarcoplasmic reticulum lumen local depletion and RyR’s stochastic attrition could be the reasons of Ca²⁺ spark termination.

Endolysin of bacteriophage T5 (EndoT5) is a Zn2+-dependent and Ca2+-activated L-alanyl-D-glutamate peptidase that hydrolyses peptidoglycans during the destruction of the cell wall of the phage host bacterium Escherichia coli. To elucidate the mechanism of calcium activation, the spatial solution structure of EndoT5 in a complex with two ions - catalytic Zn2+ and regulatory Ca2+ (EndoT5-Zn2+Ca2+, PDB ID: 8P3A) was determined by high-resolution NMR and deposited in the Protein Data Bank. We show that coordination of the Ca2+ ion fix the spatial position of polar amino acid residues D113, N115 and S117. As a result, the intramolecular mobility of extended protein loops (residues 40-70 and 111-132) is significantly reduced compared to the mobility of these loops in the structure of an enzyme containing only a catalytic a Zn2+ ion (EndoT5-Zn2+, PDB ID: 2MXZ). In the stabilized EF-like calcium-binding loop (residues 111-132), the number of van der Waals interactions with amino acid residues of the globular core of the protein increases. The binding of the Ca2+ ion is accompanied by the selection of the functional states of both extended loops of the enzyme (residues 40-70 and 111-132), because of which EndoT5-Zn2+Ca2+ acquires the structural integrity necessary for catalysis. Therefore, the mechanism of activation of L-alanyl-D-glutamate peptidase of bacteriophage T5 by Ca2+ ions involves stabilization of the enzyme molecule in a catalytically active “open” conformation. This work sheds light on the structural grounds of the ion-dependent functional proteoforms of this interesting protein.

This study explores the potential of titanium disulfide (TiS2) as an active material for aqueous calcium-ion batteries (CIBs). We investigate the electrochemical redox reactions of calcium ions within TiS2 and assess its suitability for use in aqueous CIBs. Additionally, we examine the im-pact of different electrolyte concentrations on TiS2 electrode reactions. Our findings reveal that TiS2 exhibits distinct charge-discharge behaviors in various aqueous calcium-ion electrolytes. Notably, at higher electrolyte concentrations, TiS2 effectively suppresses the hydrogen genera-tion reaction caused by water decomposition, demonstrating its potential as an active material for aqueous CIBs. In-situ X-ray diffraction analysis confirms the intercalation of Ca2+ ions be-tween TiS2 layers during charging. This confirmation is groundbreaking, as it represents the first experimental evidence of calcium ions being electrochemically inserted between TiS2 layers from aqueous solutions, signifying a previously unreported achievement and strongly suggesting TiS2's applicability in aqueous CIBs. X-ray photoelectron spectroscopy analysis further supports the formation of a solid electrolyte interphase (SEI) on the TiS2 electrode surface, contributing to the suppression of electrolyte decomposition reactions. Furthermore, we investigate the influ-ence of anions in the electrolyte on charge-discharge behavior. Our findings suggest that the choice of anion coordinated with Ca2+ ions affects SEI formation and cycling performance. Un-derstanding the role of anions in SEI formation is crucial for optimizing aqueous CIBs. In con-clusion, this research underscores TiS2's potential as an active material for aqueous calcium-ion batteries and emphasizes the importance of electrolyte composition in influencing SEI formation and battery performance. These findings contribute to the development of more sustainable and efficient energy storage technologies.

For voltage-gated Ca2+ channel (VGCC), its α2δ subunits are traditionally considered to be auxiliary subunits that regulates VGCC trafficking to the plasma membrane. The antiepileptic, antinociceptive and anxiolytic gabapentin (GBP) has previously been shown to bind the VGCC α2δ subunits with high affinity to disrupt VGCC trafficking. Yet, the interaction between GBP and α2δ still remains poorly understood from a structural point of view. For instance, it is not clear yet what the structural implication is of α2δ-1-bound GBP against VGCC trafficking. With a set of experimental data-driven structural analysis of the VGCC α2δ-1 and its ligand GBP, this article postulates for the first time that: 1), α2δ-1 bound GBP stabilizes the α2δ-1-GBP complex structure; 2), α2δ-1 bound GBP restrains the conformational flexibility of α2δ-1; 3), α2δ-1-bound GBP establishes an electrostatic axis consisting of Q535 (Gln535)-R241 (Arg241)-GBP (gabapentin)-D452 (Asp452), which constitutes an energetically favourable contribution towards the structural stability of the α2δ-1-GBP complex and helps restrains the conformational flexibility and local structural rigidification of α2δ-1; and 4), GBP-induced local conformational inflexibility and structural rigidification of α2δ-1 is one key step in the pharmacological disruption of VGCC trafficking by GBP.

Climate change and the increasing frequency of high-temperature events are significant threats to global crop yields. To address this, a comprehensive understanding of how plants respond to heat shock (HS) is essential. Signaling pathways involving calcium (Ca2+), a versatile second messenger in plants, encode information through temporal and spatial variations in ion concentration. Ca2+ is detected by Ca2+-sensing effectors, including channels and binding proteins, which trigger specific cellular responses. At elevated temperatures, the cytosolic concentration of Ca2+ in plant cells increases rapidly, making Ca2+ signals the earliest response to HS. In this review, we discuss the crucial role of Ca2+ signaling in raising plant thermotolerance and we explore its multifaceted contributions to various aspects of the plant HS response.

Tomato (Solanum lycopersicum L.) has almost 190 million tonnes produced in 2023. Tomato fruit suffer losses of up to 50% during harvest and transport, which causes financial hardship, reduces the amount of food available and causes environmental harm. Calcium plays an important role in cell wall strength. This work assessed the use of a calcium transport stimulants (MCAS) to increase the firmness of tomato fruit in the laboratory and the foliar application to tomato plants. Then handling damage was simulated. In the laboratory, the calcium with MCAS significantly increased the fruit firmness compared to the untreated and calcium without MCAS, which were not significantly different. When calcium with MCAS was applied to tomato plants foliarly before harvest, the calcium with MCAS treated fruit were significantly firmer than the untreated or calcium without MCAS treated fruit for up to 10 weeks after harvest, and this was achieved by applying only 0.91 kg ha-1 calcium. Finally, when fruit were exposed to a simulated drop, the calcium with MCAS treated fruit remained firmer than the undamaged fruit or dropped fruit with calcium without MCAS. Calcium with MCAS could significantly increase the fruit firmness and increase the shelf-life of tomatoes while applying less calcium.

The study aimed to optimize protocols for the joint extraction of deoxyribonucleic acid (DNA) and ribonucleic acid (RNA) from 0.025 x 106 CFU of Candida albicans, aiming to overcome challenges in the extraction of these genetic materials. From this, treated Silicon Carbide (SiC) granules were added to fungal samples from methods 1, 2 and 3 obtained from aliquots of BHI or Sabouraud medium to cause cell lysis and enable the isolation of these macromolecules by phenol and chloroform. The concentration and integrity of nucleic acids were obtained, respectively, by spectrophotometry using A260/A280 ratios and 1% agarose gel electrophoresis. Therefore, method 3 is the one that most comprises samples considered pure of both DNA and RNA, simultaneously. Furthermore, the presence of intact RNAs corresponding to the base pair size, such as 5.8 S rRNA and tRNA, was verified during electrophoresis, taking into account the particularities of RNA, which makes it very unstable and easily degraded. Therefore, it results in a faster and simpler method in addition to obtaining promising results using minimal amounts of biological sample, thus offering a valuable alternative for small laboratories working with molecular biology.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes. There are various types of canals, including calice, axial canals, and other internal canals, with structures that are dynamically altered during different coral growth states due to internal calcium transport. However, few studies have considered the regulation of calcium transport in Acropora. In this study, we investigated the morphological changes of the axial canal in six Acropora muricata samples by high resolution micro-computed tomography, observing the patterns of the axial canal during the processes of new branch formation and truncated branch rebuilding. We visualized the formation of a new branch from a calice and deposition of the iconic hexactin skeletons in the axial canal. Furthermore, the diameter and volume changes of the axial canal in truncated branches during rebuilding processes were calculated, revealing that the volume ratio of calcareous deposits in the axial canal exhibit significant increases within the first three weeks, returning to levels in the initial state in the following week. This work indicates that the axial canal can transport calcium to form hexactin skeletons in a new branch and rebuild the tip of a truncated branch. The calcium transport along canal network regulates various growth processes, including budding, branching, skeleton forming, and self-rebuilding of an Acropora colony. Understanding the changes in canal function under normal and extreme conditions will provide theoretical guidance for restoration and protection of coral reefs.

Background: Since circa 1980, a model of neocortical interactions, Statistical Mechanics of Neocortical Interactions (SMNI) has been successful in calculating many experimental phenomena, including fits to electroencephalographic (EEG) data in attention tasks, using an importance-sampling code Adaptive Simulated Annealing (ASA). The SMNI model is developed in the context of classical path-integrals, which affords intuitive insights as well as direct numerical benefits, e.g., using the effective Action as a a cost/objective function for parameter fits to data. Objective: Previous authors have fit affective EEG data to neural-network models. This project seeks to use models based on physics and biology to fit this same data. Previous work showed improvements in fits to EEG for attention states; this project extends these methods to affective states. Method: Path integrals are used in both classical and quantum contexts. Classical path integrals are used to define a cost/objective function to fit data, and quantum path integrals are used to derive a closed-form analytic expression for Ca-ion waves in the presence of a magnetic vector potential which is generated by highly synchronous neuronal firings which give rise to EEG. ASA is used to fit EEG data. Results: The mathematical-physics and computer parts of the study are successful, in that cost/objective functions used to fit EEG data using these models are consistent with previous work published by other authors. However, since the SMNI model includes these quantum effects, this is another reason to continue examining these issues. The results here are consistent, not better, than previous work using neural-network models, albeit only one parameter was used here, instead of multiple filters and kernels used previously on such data. Conclusion: Although these quantum effects are highly speculative, explicit calculations have shown them to be consistent with experimental data, at least to date. The current supercomputer project extends this model to affective/emotion data. Results from several authors using neural-network approaches at individual electrode sites show some predictive capabilities; the results given here are consistent with these other results. However, since the SMNI model includes these quantum effects, this is another reason to continue examining these issues.

Protons are gaining increasing attention as neurotransmitters due to their extraordinary abilities to rapidly transfer electrical charge, mobilize cellular calcium and modulate ion channels. How all this is possible is currently the subject of in-depth studies and discussions concerning not only neurophysiology, but also biological materials for artificial intelligence. In this short review, some biochemical mechanisms are described by which protons, in combination with calcium, can initiate firing in sensory neurons and transmit impulse across synapses. Furthermore, mechanisms are put forward concerning how three neurotransmitters, glutamate, gamma-aminobutyric acid and acetylcholine, are able to generate protons. The results of the numerous experimental works taken into consideration indicate that protons can play a fundamental role both in the generation and in the transmission of the nerve impulse.

In recent years, technical processes for the sequestration of CO2 through industrial waste mineral carbonation have been explored and developed. There is a large portfolio of Carbon Capture, Uti-lisation and Storage (CCUS) techniques that have been employed on a laboratory and at pilot scale. These include geological storage, ocean storage and mineralisation by carbonate ores. In view of this, the main purpose of this research was to investigate and explore chemical variables, particularly ammonium salts as lixiviants for calcium mineral extraction from iron making slag. The slag in use was acquired from a Steel Mill in the Vaal Triangle Region in Gauteng, South Af-rica. The experimental test work was conducted using different ammonium lixiviants, namely, NH4NO3, NH4Cl and CH3COONH4 to understand the influence of anion type as well as possible differences in mechanisms of interactions. Lixiviant concentration as well as the reaction time were varied in this research study. The three selected ammonium based lixiviants showed different extents of calcium extraction owing to differences in the anion groups. NH4NO3, NH4Cl and CH3COONH4 were found capable of dissolving 50% to 80% of calcium from the selected slag for different molar concentrations. Anion type and leaching time also had significant influences on the leaching of calcium from the slag. Rapid pH degradation resulted in better calcium extraction ca-pabilities. This work has shown that the selected ammonium salts have a potential as lixiviants for calcium dissolution from iron making blast furnace slags. These lixiviants would therefore be important to consider during calcium mineral carbonation for CO2 sequestration.

Calcium (Ca2+) ions act as second messenger, regulating several cell functions. Mitochondria are critical organelles for the regulation of intracellular Ca2+. Mitochondrial calcium (mtCa2+) uptake is ensured by the presence in the inner mitochondrial membrane (IMM) of the mitochondrial calcium uniporter (MCU) complex, a macromolecular structure composed of pore-forming and regulatory subunits. MtCa2+ uptake plays a crucial role in the regulation of oxidative metabolism and cell death. Many evidences demonstrate that dysregulation of mtCa2+ homeostasis can have serious pathological outcomes. In this review, we briefly discuss the molecular structure and the function of the MCU complex and then we focus our attention on human diseases in which a dysfunction in mtCa2+ has been showed.

Abstract: Calcium-based catalysts are of a high interest for glycerol polymerization due to their high catalytic activity and large availability. However, their poor stability under reaction conditions is an issue. In the present study, we investigated the stability and catalytic activity of Ca-hydroxyapatites (HAps) as one of the most abundant Ca-source in nature. A stochiometric, a Ca-deficient and a Ca-rich HAps have been synthetized and tested as catalysts in the glycerol polymerization reaction. Deficient and stochiometric HAps exhibited a remarkable 100% selectivity to triglycerol at 15 % of glycerol conversion at 245 °C after 8 h of reaction in the presence 0.5 mol.% of catalyst. Moreover, under the same reaction conditions, Ca-rich HAp showed a high selectivity (88 %) to di- and triglycerol at a glycerol conversion of 27 %. Most importantly, these catalysts were unexpectedly stable towards leaching under the reaction conditions based on the ICP-OES results. However, based on the catalytic tests and characterization analysis performed by XRD, XPS, IR, TGA-DSC and ICP-OES, we found that HAps can be deactivated by the presence of the reaction products themselves, i.e., water and polymers.

The most important prognostic factors in curatively treated prostate cancer at the initial diagnosis are T and N stage, histological subtype, Gleason score, initial PSA, PSA density and percentage of core biopsy positivity. Newer, but non-standard prognostic factors are urine PCA3 and genetic markers of prostate cancer. A simple, but seemingly underestimated standard test is serum Calcium (Ca) level, which has been shown by a previous study group to be a good predictor of lethal prostate cancer, but there is scarce evidence regarding the prognostic value of calcium levels at diagnosis. We aimed to determine whether a Ca level in the upper part of normal values has a prognostic value in curatively treated prostate cancer. We have retrospectively included 84 consecutive patients with prostate cancer, who underwent curative radiotherapy (primary or adjuvant; external beam RT with or without brachytherapy). We have performed statistical analysis of available prognostic factors. Ca level at diagnosis was found to be a statistically significant predictor of disease-free survival.

In this review article, we present the major insights from and challenges faced in the acquisition, analysis and modeling of astrocyte calcium activity, aiming at bridging the gap between those fields to crack the complex astrocyte \enquote{Calcium Code}. We then propose strategies to reinforce interdisciplinary collaborative projects to unravel astrocyte function in health and disease.

The aim of the study was to determine the maximum safe concentration of calcium and phosphate in neonatal parenteral nutrition (PN) solutions when various combinations of inorganic and organic salts are applied. Twelve PN solutions for neonatal use were aseptically prepared. Increasing concentration of inorganic and organic calcium and phosphate were added to the standard formulas. Each admixture was separately tested according to following conditions; after mixing, 37°C for 24 h, and maximum safe combination of calcium and phosphate were stored at 4°C for 30 days and followed by 24 h at 37°C. Visual inspections against a black and white contrast background, microscopic observation of undiluted PN solutions as well as the membrane filter after filtration of the PN solution, pH evaluation, and spectrophotometry at 600 nm were examined in triplicate. Safe maximum concentration of organic and inorganic calcium and phosphate was proposed individually for each composition of parenteral nutrition solutions. Surprisingly organic calcium with organic phosphate showed precipitation but over the therapeutic range. The protective effect of amino acid was observed and higher concentrations of calcium and phosphate were free of precipitation.

Cadmium (Cd) contamination in rice grains is posing a significant threat to global food security. To restrict the transport of Cd in the soil-rice system, an efficient way is to use the ionomics strate-gy. Since calcium (Ca) and Cd have similar ionic radii, their uptake and translocation may be linked in multiple aspects in rice. However, the underlying antagonistic mechanisms are still not fully understood. Therefore, we first summarized the current knowledge on the physiological and molecular footprints of Cd translocation in plants and then explored the potential antagonistic points between Ca and Cd in rice, including exchange adsorption on roots, plant cell wall compo-sition, co-transporter gene expression, and transpiration inhibition. This review provides sugges-tions for the Ca/Cd interacting study in rice and introduces the ionomics research to better control the accumulation of Cd in plants.

This work presents the production and incorporation of calcium hydrolyzed nano-solutions at three concentrations (1, 2, and 3 wt.%) in alkali-activated gold mine tailings (MTs) from Arequipa, Perú. A first activator solution of sodium hydroxide (NaOH) at 10M was used. The calcium hy-drolyzed nano-solutions acted as a secondary activator and as additional calcium resource for the alkali-activated materials (AAMs) based on the low-calcium gold MTs. High-resolution trans-mission electron microscopy/energy-dispersive x-ray spectroscopy (HR-TEM/EDS) analyses were carried out to characterize the morphology, size, and structures of the calcium hydrolyzed na-noparticles. Fourier transform infrared (FTIR) analyses then were used to understand the chemical bonding interactions in the calcium hydrolyzed nanoparticles and in the AAMs. Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS) and Quantitative X-ray diffraction (QXRD) were performed to study the structural, chemical, and phase compositions of the AAMs; uniaxial compressive tests evaluated the compressive strength of the reacted AAMs; and Nitrogen adsorption-desorption analyses measured the porosity changes at nanostructure level in the AAMs. The results indicate that each increase in the concentration of the calcium hydrolyzed nano-solution had a direct/proportional effect on the mechanical properties of the AAMs samples. The AAMs with 3 wt.% calcium-hydrolyzed nano-solution had the highest compressive strength value of 15.16 MPa, which represented an increase of 62% compared to the original system without nanoparticles and aged under the same conditions of 70°C for seven days. These results provide useful information about the positive effect of calcium-hydrolyzed nanoparticles on gold MTs and their conversion into sustainable building materials through alkali activation.

The remarkable adsorption capacity of graphene derived materials has prompted their examination in composite materials suitable for deployment in treatment of contaminated waters. In this study, crosslinked calcium alginate – graphene oxide beads were prepared and activated by exposure to pH 4 by using 0.1M HCl. The activated beads were investigated as novel adsorbents for the removal of organic pollutants (Methylene Blue dye and the pharmaceuticals Famotidine and Diclofenac) with a range of physicochemical properties. Effects of initial pollutant concentration, temperature, pH and adsorbent dose were investigated and kinetic models were examined for fit to the data. Maximum adsorption capacities q_max obtained were 1334, 35.50 and 36.35 mg g^-1 for the uptake of Methylene blue, Famotidine and Diclofenac respectively. The equilibrium adsorption had an alignment with Langmuir isotherms while the kinetics were most accurately modelled using a pseudo- first –order and second order models according to the regression analysis. Thermodynamic parameters such as ΔG^◦, ΔH^◦ and ΔS^◦ were calculated and the adsorption process was determined to be exothermic and spontaneous.

Pollen tubes grow by spatially and temporally regulated expansion of new material secreted into the cell wall at the tip of the tube. A complex web of interactions among cellular components, ions and small molecule provides dynamic control of localized expansion and secretion. Cross-correlation studies on oscillating lily (Lilium formosanum Wallace) pollen tubes showed that an increase in intracellular calcium follows an increase in growth, whereas the increase in the alkaline band and in secretion both anticipate the increase in growth rate. Calcium, as a follower, is unlikely to be a stimulator of growth, whereas the alkaline band, as a leader, may be an activator. To gain further insight herein we reversibly inhibited growth with potassium cyanide (KCN), and followed the re-establishment of calcium, pH and secretion patterns as growth resumed. While KCN markedly slows growth and causes the associated gradients of calcium and pH to sharply decline, its removal allows growth and vital processes to fully recover. The calcium gradient reappears before growth restarts, however it is preceded by both the alkaline band and secretion, in which the alkaline band is slightly advanced over secretion. Thus the pH gradient, rather than the tip-focused calcium gradient, may regulate pollen tube growth.

Background: Current treatment for Chronic Kidney Disease (CKD) focuses on improving manifestations and delaying progression. Nutritional approaches play a crucial role in CKD management, and various supplements have become available. Ketoanalogues of amino acids (KA), calcum citrate, and inulin have been proposed as suitable supplements, yet their widespread use has been limited due to insufficient evidence. This study aimed to generate general guidance statements on the appropriateness of these supplements through a RAND/UCLA consensus process; Methods: A RAND/UCLA consensus panel was convened to evaluate the appropriateness of these supplements in different clinical scenarios. In this study, we present a subgroup analysis focusing on a panel of eleven clinical nephrologists from among the experts; Results: Supplementation of low protein diets (LPD) and very low protein diets (VLPD) with KA was considered appropriate to reduce manifestations and delay CKD outcomes, supplementation with calcium citrate is considered appropriate to reduce CKD manifestations, and supplementation with inulin is considered appropriate to delay CKD outcomes and manage comorbidities; Conclusions: Based on a combination of clinical experience and scientific evidence , the panel reached a consensus that KA supplementation of LPD and VLPD, calcium citrate, and inulin are appropriate in patients with CKD across various scenarios.

Introduction: This study aims to elucidate the clinical diagnostic value of S100 Calcium Binding Protein beta (S100B) in epilepsy, a topic of ongoing debate among European and Asian epilepsy research centres.Methods and analysis: A structured long-term research plan was developed, comprising three phases. Phase one involves observational studies investigating the correlation between S100B levels in serum or cerebrospinal fluid and epilepsy. Phase two integrates observational and randomised controlled data to establish baseline S100B levels across diverse epilepsy demographics, underpinning the predictive value of S100B for epilepsy. Phase three focuses on randomised controlled trials to evaluate the diagnostic accuracy of S100B as an epilepsy biomarker.Ethics and dissemination: All enrolled patients will provide written consent. The ethics committee of the Second People’s Hospital of Gansu Province, Affiliated Hospital of Northwest Minzu University, China, approved the study (GSSEY2022-KY009-01).Registration: The study is registered with PROSPERO (CRD42023425431).

The intricate functionality of the vertebrate retina relies on the interplay between neurotransmitter activity and calcium dynamics, offering important insights into de-velopmental processes, physiological functioning, and disease progression. Neuro-transmitters orchestrate cellular processes to shape the behavior of the retina under diverse circumstances. Despite research to elucidate the roles of individual neuro-transmitters in the visual system, there remains a gap in our understanding of the holistic integration of their interplay with calcium dynamics in the broader context of neuronal development, health, and disease. To address this gap, the present review explores the mechanisms used by the neurotransmitters glutamate, GABA, glycine, dopamine, and acetylcholine and their interplay with calcium dynamics. This con-ceptual outline is intended to inform and guide future research, underpinning novel therapeutic avenues for retinal-associated disorders.

In 2021 the total world cement production was estimated at 4.1 billion tonnes and the annual CO2 emissions from cement plants reached almost 2.8 billion metric tonnes. In the last years many ef-forts have been made for manufacturing low-CO2 cements. In this regard, a great attention has been paid towards calcium sulfoaluminate (CSA) cements for both their peculiar technical prop-erties and the environmentally friendly features mainly related to their manufacturing process. Moreover, the use of blended cements composed by CSA binders and supplementary cementitious materials (SCMs) could represents a powerful tool for both reducing the CO2 footprint and pro-ducing more durable environmentally friendly materials. In this paper, the possibility of using reservoir sediments (RS), calcined at 830°C, as SCMs in blended-CSA cements was investigated. Four binders were submitted to hydration and physico-mechanical tests for curing periods com-prised in the interval 4 hours-56 days. X-ray fluorescence, X-ray diffraction and differential thermal–thermogravimetric analyses were employed as main characterization techniques. It was found that thermally treated RS are very interesting inasmuch as their utilization allows a CSA clinker dilution, thus implying both a decrease of CO2 emissions and a reduction of costs related to CSA cement production.

Calcium sulfate (CS) materials containing terbium ions at 0, 1.0, or 2.0 mol.% were obtained by mechanochemical synthesis. According to X-ray diffraction data, the powder materials are characterized by the presence of a CaSO4×0.5H2O phase, while Tb3+ is incorporated into the lattice at ≤1.0 mol.%. Specific surface area enlarged from 2.1 to 22.5 m2/g as crystallite size decreased from 68 to 31 nm and the Tb3+ concentration increased up to 1.0 mol.%. Thermal analysis showed that terbium slightly raises the temperature of CaSO4×2H2O-to-CaSO4 transition. The presence of Tb3+ did not affect the solubility of the CS cements. Furthermore, after 7 days of soaking of the materials in a simulated body fluid, a calcium phosphate layer formed corresponding to a hydroxyapatite phase, in contrast to the pure cements. Luminescent properties were studied by excitation at 276 nm. The recorded emission peaks of the CS materials indicated that the luminescence of the samples is green and blue, with the most intense luminescence observed for samples containing 1.0 mol.% Tb3+. The developed materials can find applications in medicine as bioimplants for the regeneration and restoration of bone tissue with a possibility of noninvasive monitoring of the bone restoration process.

This review article deals with the design of bioactive calcium phosphate coatings deposited on metallic substrates to produce bone implants. The bioceramic coating properties are used to create a strong bonding between the bone implants and the surrounding bone tissue. They provide a fast response after implantation and increase the lifespan of the implant in the body environment. The first part of the article describes the different compounds belonging to the calcium phosphate family and their main properties for applications in biomaterials science. The calcium to phosphorus atomic ratio (Ca/P)at. and the solubility (Ks) of these compounds define their behavior in a physiological environment. Hydroxyapatite is the gold standard among calcium phosphate materials, but other chemical compositions/stoichiometries have also been studied for their interesting properties. The second part reviews the most usual deposition processes to produce bioactive calcium phosphate coatings for bone implant applications. Plasma spraying is the main industrial process, but magnetron sputtering, pulsed laser deposition, electrospray deposition, electrophoretic deposition, and electrodeposition are also widely studied in academic and industrial research. The last part describes the main physicochemical properties of calcium phosphate coatings and their impact on the bioactivity of bone implants in a physiological environment.

Herbicides are widely used in agriculture to control weeds and enhance crop productivity. However, their application can have significant impacts on soil health and nutrient dynamics. This paper reviews the effects of herbicides on soil properties, microbial communities, and nutrient availability, with a particular focus on calcium deficiency. The review synthesizes findings from peer-reviewed journals and reports, including research conducted in Australia. The correlation between herbicide application and calcium deficiency is explored, highlighting both positive and negative impacts. The paper concludes with recommendations for sustainable herbicide use and alternative weed management strategies.

Surface treatment of implants facilitates osseointegration, with nanostructured surfaces exhibiting accelerated peri-implant bone regeneration. This study compared bone-to-implant contact (BIC) in implants with hydroxyapatite (HA), sand-blasted and acid-etched (SLA), and SLA with calcium (Ca)-coated (XPEED®) surfaces. Seventy-five disk-shaped grade 4 Ti specimens divided into three groups were prepared, with 16 implants per group tested in New Zealand white rabbits. Surface characterization was performed using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), digital microscopy, and a contact angle analyzer. Cell viability, proliferation, and adhesion were assessed using MC3T3-E1 cells. Apatite formation was evaluated using modified simulated body fluid (m-SBF) incubation. After 4 weeks of healing, the outcomes reviewed were BIC, bone area (BA), removal torque tests, and histomorphometric evaluation. Microstructure analysis revealed irregular pores across all groups, with the XPEED group exhibiting a nanostructured Ca-coated surface. Surface characterization showed a crystalline CaTiO3 layer on XPEED surfaces, with evenly distributed Ca penetrating the implants. All surfaces provided excellent environments for cell growth. The XPEED and SLA groups showed significantly higher cell density and viability with superior osseointegration than HA (p &lt; 0.05); XPEED exhibited the highest absorbance values. Thus, XPEED surface treatment improved implant performance, biocompatibility, stability, and osseointegration.

The development of magnesium calcium phosphate bone cements (MCPCs) have garnered big attention. MCPCs are bioactive and biodegradable and have appropriate mechanical and antimicrobial properties for use in reconstructive surgery. In this study, the cement powders based on a (Ca + Mg)/P = 2 system doped with Zn2+ at 0.5 and 1.0 wt.% were obtained and investigated. After the mixing with a cement liquid, structural and phase composition, morphology, chemical structure, setting time, compressive strength, degradation behavior, solubility, antibacterial activities, and in vitro behaviour of the cement materials were examined. A high compressive strength of 48 ± 5 MPa (mean ± SD) was achieved for the cement made from Zn2+ 1.0-wt.%-substituted powders. The Zn2+ introduction led to antibacterial activity against Staphylococcus aureus and Escherichia coli strains, with an inhibition zone diameter up to 8 mm. Biological assays confirmed that the developed cements are cytocompatible and promising as a potential bone substitute in reconstructive surgery.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

Calcium carbonate cements have been synthesized by mixing amorphous calcium carbonate and vaterite powders with water to form a cement paste and study how mechanical strength is created during the setting reaction. In-situ XRD was used to monitor the transformation of ACC and vaterite phases into calcite and a rotational rheometer was used to monitor the strength evolution. There are two characteristic time scales of the strengthening of the cement paste. The short timescale of the order 1 hour is controlled by smoothening of the vaterite grains, allowing closer and therefore adhesive contacts between the grains. The long timescale of the order 10-50 hours is controlled by the phase transformation of vaterite into calcite. This transformation is, unlike in previous studies using stirred reactors, found to be mainly controlled by diffusion in the liquid phase. The evolution of shear strength with solid volume fraction is best explained by a fractal model of the paste structure.

This study aims to investigate utilizing Precipitated Calcium Carbonate (PCC), a by-product of sugar beet, as a soil stabilizer for addressing settlement issues beneath pavements. Various tests were conducted to assess the engineering properties of PCC-stabilized subgrades using PCC obtained from Amalgamated Sugar Cooperation in Twin Falls, Idaho. Local loess samples, like those found beneath pavements, were collected for testing purposes. Initial tests involved evaluating the unconfined compressive strength of compacted loess samples, followed by tests on samples mixed with different weight percentages of PCC. The results revealed a significant average increase of 10% to 28% in the strength of loess samples stabilized with 5% PCC compared to the strength of the native soil. The chemical composition and microstructure of PCC were further analyzed through X-ray Diffraction (XRD), Energy Dispersive X-ray Spectrometer (EDX), and Scanning Electron Microscopy (SEM) Tests conducted at the Idaho National Laboratory (INL). XRD analysis indicates the presence of calcium carbonate and silica. EDX analysis unveiled a carbon content of 9% by weight in PCC, which could contribute to the carbon footprint when it breaks down. Additionally, SEM images displayed an irregular microstructure and particle shape of PCC. Furthermore, the inclusion of PCC improved the resistance of loess to saturation collapse.

Emerging evidence indicates that intracellular calcium (Ca2+) levels and their regulatory proteins play essential roles in normal stem cell proliferation and differentiation. Cancer stem-like cells (CSCs) are subpopulations of cancer cells that retain characteristics similar to stem cells and play an essential role in cancer progression. Recent studies have reported that the Orai3 calcium channel plays an oncogenic role in human cancer. However, its role in CSC remains underexplored. In this study, we explored the effects of Orai3 in the progression and stemness of oral/oropharyngeal squamous cell carcinoma (OSCC). Orai3 expression was increased in a stepwise manner during the progression of OSCC. In addition, Orai3 was highly enriched in CSC populations of OSCC. Ectopic Orai3 expression in non-tumorigenic immortalized oral epithelial cells increased intracellular Ca2+ levels, acquiring malignant growth and CSC properties. Conversely, silencing of endogenous Orai3 in OSCC cells suppressed CSC phenotype, indicating a pivotal role of Orai3 in CSC regulation. Moreover, Orai3 markedly increased the expression of inhibitor of DNA binding 1 (ID1), a stemness transcription factor. Orai3 and ID1 were highly expressed in CSCs compared to non-CSCs, implying the functional importance of the Orai3/ID1 axis in CSC regulation. Furthermore, suppression of ID1 abrogated CSC phenotype in the cell with ectopic Orai3 overexpression and OSCC. Our study reveals that Orai3 is a novel functional CSC regulator in OSCC and further suggests that Orai3 plays an oncogenic role in OSCC by promoting cancer stemness via ID1 upregulation.

Collapsibility is an inherent characteristic of loess, which is often treated by adding industrial materials such as cement and lime in engineering, it seriously damages the reclamation performance of soil. Degradable calcium lignosulfonate (CLS) has a good prospect in balancing soil stabilization and environmental protection. Therefore, this paper evaluates the collapsibility and mechanical characteristics of CLS improved loess based on the collapsibility test, grey correlation analysis, and unconfined compressive strength test. The results show that when the content is 3%, the stabilization effect is most obvious, and the collapsibility coefficient can be reduced by more than 95%. The order of grey correlation degree of collapsibility on each index is moisture content, void ratio, dry density, and CLS content from large to small. The unconfined compressive strength increases rapidly in the first 14 days and then decreases with the content. When the content is too high, the strength of improved loess is lower than that of plain loess. Combined with SEM, microstructure parameters, and X-ray diffraction analysis, the carbonate minerals can play the role of filling pores and connecting soil particles, which reduces the grain size of mineral composition and the thickness of the electric double layer and makes the structure more compact. The research results have scientific significance and application value for the ecological modification research and engineering application of soil.

Owing to its properties, boron carbide has been applied in scientific and industrial fields. For this reason, B4C powders should be characterized by high purity and homogeneity in grain size and shape. In this study, boron carbide was prepared using precursors obtained by a hydrothermal method, and the grain morphology of the product was investigated. Boric acid and the saccharides glucose, fructose, inulin, and sorbitol were used as the precursors. Two precursor dehydration methods, freeze-drying and recrystallization, were compared. The precursors were subjected to DLS grain size and FT-IR spectrophotometric studies, and SEM observations of the precursors and products were performed, confirming that boron carbide powders with submicron spherical grains could be successfully synthesized.

This study explored the feasibility of fluoride removal from simulated semiconductor industry wastewater and its recovery as calcium fluoride using fluidized bed crystallization. The continuous reactor showed best performance (>90% fluoride removal and >95% crystallization efficiency) at a calcium to fluoride ratio of 0.6 within first 40 days of continuous operation. The resulting particle size increased by more than double during this time along with a 36% increase in the seed bed height indicating deposition of CaF2 onto the silica seed. The SEM-EDX analysis showed the size and shape of the crystals formed along with high amount of Ca-F ions presence. The purity of the CaF2 crystals were determined to be 91.1% though ICP-OES analysis. Following the continuous experiment, different process improvement strategies are explored. The addition of excess amount of calcium resulted in an additional 6% fluoride removal, however, compared to this single stage process, a two-stage approach was found to be better strategy to achieve a low effluent fluoride concentration. The fluoride removal reached 94% with this two-stage approach under optimum condition of 4 + 1 h HRT combinations and a [Ca2+]/[F-] ratio of 0.55 and 0.7 for the two reactors, respectively. CFD simulation showed the impact of inlet diameter, bottom-angle shape and width and height ratio of the reactor on mixing inside reactor and possibility of further improvement in reactor performance by optimizing the FBR configuration.

The Cav3.2 T-type calcium channel is implicated in various pathological conditions, including cardiac hypertrophy, epilepsy, autism, and chronic pain. Phosphorylation of Cav3.2 by multiple kinases plays a pivotal role in regulating its calcium channel function. The calcium/calmodulin-dependent serine/threonine phosphatase, calcineurin, interacts physically with Cav3.2 and modulates its activity. However, it remains unclear whether calcineurin dephosphorylates Cav3.2, the specific spatial regions on Cav3.2 involved, and the extent of the quantitative impact. In this study, we elucidated the serine/threonine residues on Cav3.2 targeted by calcineurin using quantitative mass spectrometry. We identified six serine residues in the N-terminus, II-III loop, and C-terminus of Cav3.2 that were dephosphorylated by calcineurin. Notably, a higher level of dephosphorylation was observed in the Cav3.2 C-terminus, where calcineurin binds to this channel. Additionally, a previously known CaMKII-phosphorylated site, S1198, was found to be dephosphorylated by calcineurin. Furthermore, we also discovered that a novel CaMKII-phosphorylated site, S2137, underwent dephosphorylation by calcineurin. In CAD cells, a mouse central nervous system cell line, membrane depolarization led to an increase in the phosphorylation of endogenous Cav3.2 at S2137. Mutation of S2137 affected the calcium channel function of Cav3.2. Our findings advance the understanding of Cav3.2 regulation not only through kinase phosphorylation but also via calcineurin phosphatase dephosphorylation.

The injectable hydrated calcium phosphate bone-like paste (hCPP) have been developed with suitable nanoscale characteristics and unindered injection through 23G standard needles. In vitro assays showed the cytocompatibility of hCPP with mesenchymal embryonic C3H10T1/2 cell cultures. The hCPPs were identified to be composed of aggregated nano-sized particles with sphere-like shapes with low crystallinity. The ability of serum proteins (FBS) to adsorb on hCPP particles was also studied. The hCPP demonstrated high protein adsorption capacity, thereby indicating its potential in various biomedical applications. The results of the in vivo assay upon subcutaneous injection in Wistar rats indicated the nontoxicity and biocompatibility of experimental hCPP, as well as the gradual resorption of hCPP, comparable to the period of bone regeneration. The data obtained are of great interest for the development of commercial highly effective osteoplastic materials for bone tissue regeneration and augmentation.

This paper addresses the effect of both microstructure and relative humidity on the long-term creep properties of sustainable calcium carbonate (CaCO₃) cements. Those can be prepared by mixing amorphous calcium carbonate and vaterite with water. A larger starting amount of vaterite, X_V, within the mixture design gives a higher elasticity and resistance to the specimens due to the larger overall bridging area within the newly formed calcite crystals. Regarding creep properties for a given relative humidity, the amplitude of creep strain decreases with X_V, and makes the relation between the elastic modulus, E, and hardness, H, of the samples to be linear with the contact creep modulus, C. On the other hand, for a given composition, the amplitude of creep increases with the relative humidity, making the contact creep modulus, Ci, to rise exponentially with the elastic modulus, E, and hardness, H, of the specimens. The most probable creep mechanisms for this kind of cement seem to be a combination of microcraking in the early stages and dissolution and reprecipitation of calcite in the long-term (also known as pressure solution theory). The presence of water in pores with increasing relative humidity might enhance the local dissolution of calcite, and hence the creep amplitude.

Cardiac aging is characterized by alterations in contractility and intracellular calcium ([Ca²⁺]_i) homeostasis. It has been suggested that oxidative stress may be involved in this process. We and others have reported that in cardiomyopathies the NADPH oxidase (NOX)-derived superoxide is increased, with a negative impact on [Ca²⁺]_i and contractility. We tested the hypothesis that in the aged heart, [Ca²⁺]_i handling and contractility are disturbed by NOX-derived superoxide. Contractility was evaluated isolated hearts, challenged with isoproterenol. To assess [Ca²⁺]_i, isolated cardiac myocytes were field-stimulated and [Ca^2+]_i was monitored with fura-2. Cardiac concentration-response to isoproterenol was depressed in aged compared to adults hearts (p < 0.005), but was restored by NOX inhibitors apocynin and VAS2870. In isolated cardiomyocytes, apocynin increased the amplitude of [Ca²⁺]_i in aged myocytes (p < 0.05). Time-50 [Ca²⁺]_i decay was increased in aged myocytes (p < 0.05) and reduced towards normal by NOX inhibition. In addition, we found that myofilaments Ca²⁺ sensitivity was reduced in aged myocytes (p < 0.05), and further reduced by apocynin. Finally SERCA levels but not phospholamban were reduced in aged hearts (p < 0.05). In conclusion, β-adrenergic‒induced contractility was depressed in aged hearts, and NOX inhibition restored back to normal. Moreover, altered Ca²⁺ handling in aged myocytes was also improved by NOX inhibition. These results suggest a NOX-dependent effect in aged myocytes at the level of Ca²⁺ handling proteins and myofilaments.

Alzheimer’s disease (AD) and Parkinson’s disease (PD) are the two most common neurodegenerative diseases in elderly. The key histopathological features of these diseases are the presence of abnormal protein aggregates and the progressive and irreversible loss of neurons in specific brain regions. The exact mechanisms underlying the etiopathogenesis of AD or PD remain unknown, but there is extensive evidence indicating that excessive generation of reactive oxygen species (ROS) and reactive nitrogen species (RNS) along with a depleted antioxidant system, mitochondrial dysfunction, and intracellular Ca2+ dyshomeostasis play a vital role in the pathophysiology of these neurological disorders. Due to an improvement in life expectancy, the incidence of age-related neurodegenerative diseases has significantly increased. However, there is no effective protective treatment or therapy available but rather only very limited palliative treatment. Therefore, there is an urgent need for the development of preventive strategies and disease-modifying therapies to treat AD/PD. Because dysregulated Ca2+ metabolism drives oxidative damage and neuropathology in these diseases, the identification or development of compounds capable of restoring Ca2+ homeostasis and signaling may provide a neuroprotective avenue for the treatment of neurodegenerative diseases. In addition, a set of strategies to control mitochondrial Ca2+ homeostasis and signaling has been reported, including decreased Ca2+ uptake through voltage-operated Ca2+ channels (VOCCs). In this article, we review the modulatory effects of several heterocyclic compounds on Ca2+ homeostasis and trafficking, and their ability to regulate compromised mitochondrial function and associated free radical production during the onset and progression of AD or PD. This comprehensive review also describes the chemical synthesis of the heterocycles and summarizes the clinical trial outcomes.

Dissolved calcium (Ca2+) concentrations in freshwater ecosystems are of growing concern as increasing levels have been implicated in altering the environmental conditions and biodiversity. Elevated Ca2+ levels and sporadic re-emergence and disappearance of invasive zebra mussels in Kentucky Lake in recent years served as a motivation for this study. The objective of this study was to determine Ca2+ spatial and temporal patterns in Kentucky Lake, selected tributary streams, and the Ohio River during and following a zebra mussel invasion. Over 1000 water samples were collected and analysed for dissolved calcium during 2018-2022. Approved analytical methods were followed for sampling and measuring dissolved calcium levels. Results revealed significant spatial and temporal patterns. Kentucky Lake Ca2+ levels varied between 15-25 mg/L depending on the sampling location and month/year. Kentucky Lake channel sites exhibited comparably higher concentrations of Ca 2+ than did most embayment and/or stream sites, indicating that tributary streams did not serve as primary sources of calcium to the lake. Dissolved calcium levels at main lake sites exceeded the threshold for zebra mussel growth and reproduction in 2018 during the time when zebra mussels were present. Calcium in lake water samples collected from 2019 through 2022 was at or just below the threshold. Temporal trend data showed a gradual increase in Ca2+ in Kentucky Lake throughout the study period but remaining at or below the threshold level considered critical for the zebra mussels’ reproduction and development. Calcium levels in the Ohio River site at Paducah were similar to Kentucky Lake reflecting the predominance of Tennessee River water, while levels at the Brookport site were consistent with values known to support zebra mussel populations. The elevated calcium levels in Kentucky Lake waters during the late winter and early spring months may be due to natural sources (mineral weathering) as well as human activities in the Tennessee River basin. This study emphasizes the need for continued calcium monitoring in the watershed to determine the potential for future zebra mussel outbreaks and potential influences on the lake ecosystem and its functions.

Ferroptosis is an iron-dependent cell death pathway that involves depletion of intracellular glutathione (GSH) levels and iron-mediated lipid peroxidation. Ferroptosis is experimentally caused by inhibition of the cystine/glutamate antiporter xCT, which depletes cells of GSH, or by inhibition of Glutathione peroxidase 4 (GPx4), a key regulator of lipid peroxidation. The events that occur between GPx4 inhibition and the execution of ferroptotic cell death are currently a matter of active research. Previous work has shown that calcium release from the endoplasmic reticulum (ER) mediated by ryanodine receptor (RyR) channels contributes to ferroptosis-induced cell death in primary hippocampal neurons. Here, we used SH-SY5Y neuroblastoma cells, which do not express RyR channels, to test if calcium release mediated by the inositol 1,4,5-trisphosphate receptor (IP3R) channel plays a role in this process. We show that inhibition of GPx4 by RAS Selective Lethal Compound 3 (RSL3) generated an increase in reactive oxygen species (ROS), increased cytoplasmic and mitochondrial calcium levels, increased lipid peroxidation and caused cell death. The RSL3-induced calcium signals were inhibited by Xestospongin B, an inhibitor of the ER-resident IP3R calcium channel, by decreasing IP3R levels with carbachol and by IP3R1 knock-down. The intracellular calcium chelator BAPTA-AM inhibited RSL3-induced calcium signals, which were not affected by extracellular calcium depletion. We propose that GPx4 inhibition activates IP3R-mediated calcium release in SH-SY5Y cells, leading to increased cytoplasmic and mitochondrial calcium levels, which in turn stimulate the production of ROS and induce lipid peroxidation and ferroptotic cell death in a noxious positive feedback cycle.

The research on calcium leaching of 3D printed cement pastes (3DPC) exposed in aggressive water is limited, and the mechanism underlying its effect needs to be better understood. The performance anisotropy of degraded 3DPC due to calcium leaching is investigated in this paper. Samples with aggregate micro fines (AMF) and fly ash (FA) were prepared. A 6 mol/L NH₄Cl solution was used in the accelerated experiment. At specific leaching durations, performances were tested on the samples in different leaching directions. Results show that the performances of 3DPC in aggressive water have a significant anisotropic behavior. The evolution of pore defects and hydration products mainly governs the performance anisotropy of degraded 3DPC. The remaining hydration products of the surface of 3DPC leached in the Z direction are less than the other two directions because calcium ions leached in the Z direction are difficult to be compensated through weak interfaces between layers.

Calcium-activated chloride secretion in epithelial tissues described for many years. However, the molecular identity of the channel responsible for the Ca2+-activated Cl− secretion in epithelial tissues has remained a mystery. More recently, TMEM16A has been identified as a new putative Ca2 -activated Cl- channel (CaCC),. The primary goal of this article will be to review the characterization of TMEM16A, as it relates to the physical structure of the channel, as well as, important residues that confer voltage and Ca2+-sensitivity of the channel. This review will also discuss the role of TMEM16A in epithelial physiology and potential associated-pathophysiology. This will include discussion of developed knockout models that have provided much needed insight on the functional localization of TMEM16A in several epithelial tissues. Finally, this review will examine the implications of the identification of TMEM16A as it pertains to potential novel therapies in several pathologies.

Inspired by the process of bone formation in living organisms, many studies have been conducted to develop organic-inorganic composite materials by generating calcium phosphate crystals within solutions or dispersions of polymers with appropriate functional groups. Bones are composite materials consisting of organic polymers (mainly Type I collagen), carbonated apatite, and water, with volume fractions 35-45%, 35-45%, 15-25%, respectively. Carbonated apatite in bone contributes to rigidity, while organic polymers and water contribute to toughness. The inorganic crystal, carbonated apatite, is a plate-shaped crystal with dimensions of 50 nm × 25 nm × 1-4 nm, generating a significant organic-inorganic interface due to its nanoscale size. This interface is believed to absorb externally applied forces to dissipate mechanical energy to thermal energy. Creating such nanometer-scale structures using top-down approaches is challenging, making bottom-up methods like co-precipitation of polymer and inorganic crystals more suitable. In this account, efforts to develop eco-friendly mechanical materials using biomass such as cellulose and starch based on the bottom-up approach to bone-like composites are described.

Calcium-activated potassium channels (KCa) are the important participants in calcium signaling pathways due to their ability to be activated by increase of the intracellular free calcium concentration. KCa channels are involved in the regulation of various processes in the cells under normal, as well as pathophysiological conditions, including oncotransformation. Previously, with the use of patch-clamp method, we registered the KCa activity in the plasma membrane of human myeloid leukemia K562 cell line. Here, we performed the molecular and functional identification of KCa channels and have uncovered their role in proliferation, migration and invasion of K562 cells. Using a combined approach, we identified the functional activity of SK2, SK3 and IK channels in the plasma membrane of the cells. Selective SK and IK channel inhibitors, apamin and TRAM-34, reduced the proliferative, migratory and invasive capabilities of human myeloid leukemia cells. At the same time, the viability of K562 cells was not affected by KCa channel inhibitors. Our data imply that SK/IK channel inhibitors could be used to slow down the proliferation and spreading of leukemia cells that express functionally active KCa channels in the plasma membrane.

A Mitochondrial dysfunction and oxidative stress are major contributors to the pathophysiology of neurodegenerative diseases, including Alzheimer’s disease (AD). However, the mechanisms driving mitochondrial dysfunction and oxidative stress are unclear. Familial AD (fAD) is an early onset form of AD caused primarily by mutations in the presenilin-encoding genes. Previously, using Caenorhabditis elegans as a model system to study presenilin function, we found that loss of C. elegans presenilin orthologue, SEL-12, results in elevated mitochondrial and cytosolic calcium levels. Here, we provide evidence that elevated neuronal mitochondrial generated reactive oxygen species (ROS) and subsequent neurodegeneration in sel-12 mutants are a consequence of the increase of mitochondrial calcium levels and not cytosolic calcium levels. We also identify mTORC1 signaling as a critical factor in sustaining high ROS in sel-12 mutants in part through its repression of the ROS scavenging system SKN-1/Nrf. Our study reveals that SEL-12/presenilin loss disrupts neuronal ROS homeostasis by increasing mitochondrial ROS generation and elevating mTORC1 signaling, which exacerbates this imbalance by suppressing SKN-1/Nrf antioxidant activity.

Calcium signaling and lipid metabolism are crucial in the infection processes of Apicomplexans parasites. Thus, enzymes involved in these processes can be drug targets against Apicomplexans. For example, in malaria infection, in-depth research into lipid metabolic pathways is crucial in understanding the parasite's infection cycle, particularly during its erythrocytic infection cycle, which has been demonstrated to be a critical stage during the disease progression. Most enzymes that play critical roles in lipid synthesis and calcium signaling have been extensively studied; nonetheless, a vast knowledge gap still exists, especially on specific enzymes and their roles in the transmission and progression of the Apicomplexan parasites. Many types of infections caused by Apicomplexans are life-threatening and hard to treat. These intracellular parasites proliferate within parasitophorous vacuoles in their host cells. As the parasites multiply, they need to meet their high demand for nutrients such as amino acids and lipids. They can acquire nutrients through scavenging and biosynthesis. This review summarizes a few interesting, unique pathways in selected Apicomplexa and how such unique pathways can be targets for drugs.

To investigate the effect of prohexadione-calcium (Pro-Ca) primed on seed germination and seedling growth of oilseed rape under salt stress, to alleviate the inhibition of soil salinization on the growth of oilseed rape, and to improve the sustainability of agricultural production. Using Huayouza 158R and Huayouza 62 as test materials, the regulation of seed germination and seedling growth under the stresses of 0, 100, and 150 mM NaCl (S0, S100, and S150) was investigated after the primed of Pro-Ca. We conducted six treatments, S0: non-primed + 0 mM NaCl, PCS0: Pro-Ca primed + 0 mM NaCl, S100: non-primed + 100 mM NaCl, PCS100: Pro-Ca primed + 100 mM NaCl, S150: non-primed + 150mM NaCl, Pro-Ca+S150: Pro-Ca primed + 150 mM NaCl. The results showed that salt stress inhibited seed germination and seedling growth, and Pro-Ca primed significantly increased the germination index and vigor index of oilseed rape seeds. The average germination time and malondialdehyde (MDA) content were significantly reduced, which resulted in the optimal initiation fiddling concentration of 8mg·L-1. The morphological parameters of oilseed rape decreased significantly under salt stress, with leaf area decreasing by 70.69% and 75.03% and total chlorophyll content decreasing by 18.55% and 18.68% at S150. With the rise of salt stress, the changes of each photosynthetic parameter were somewhat similar, and Pn, Gs, Ci, and Tr continued to decline, indicating that the effects of salt stress on photosynthesis in oilseed rape might be mainly attributed to stomatal restriction and inhibition of photosynthetic pigment synthesis. While Na+ and MDA contents increased significantly, reaching a peak at S150, indicating that Na+ content increased significantly under salt stress, which resulted in the slow growth of oilseed rape and weak plants under the influence of Na+ salt damage. After Pro-Ca primed, leaf area and photosynthetic pigment synthesis increased, and the initiation treatment promoted the rise of Pn, Gs, Ci, and Tr under salt stress. The Na+ content decreased by 7.29% and 6.96% in PCS100 compared with S100, decreased by 9.23% and 25.02% in PCS150 compared with S150, and increased in K+ and Mg2+ after Pro-Ca primed. At this time, the antioxidant enzyme activities increased, and the MDA content and relative conductivity decreased. It was concluded that Pro-Ca primed improved the photosynthetic capacity of oilseed rape by promoting leaf growth, stomatal opening, and photosynthetic pigment synthesis. At the same time, reducing Na+ content and promoting K+ and Mg2+ absorption and antioxidant enzyme activities together alleviate salt damage and improve salt tolerance of oilseed rape.

Coffee production around the world is under threat due to climate variability and change, and drought stress will increase in many coffee regions, nutrient management practices could enhance the adaptation capacity of coffee production. Considering that coffee is a sensitive crop to boron (B) deficiency, this research investigated how B nutrition improves resistance to drought stress in coffee under controlled conditions as well how with interaction with calcium (Ca+2) influences productivity, seed compositions, and soil fertility during a production cycle of 5 year. Under controlled conditions for seven months, coffee plants were submitted to water stress with and without B nutrition. In the field, coffee plantation was submitted to two B rates (0,6 and 1,1 kg. ha-1-year-1) with fixed calcium (Ca+2) rate and, a control without Ca+2 and B. After 9 months of growth and seven months of water deficit, under controlled conditions, the application of B significantly (p&lt;0,05) reduced the negative effect of water stress on coffee growth. Under field conditions, after a production cycle of 5 years, the application of 0,6 kg B and 77 kg CaO. ha-1. year-1 yielded 14% more than the control without B and Ca+2. An increase of the B rate to 1.1 kg.ha-1.year-1 with the same Ca+2 rate increased the productivity significantly (p&lt;0,05) by 37% compared to the control. B application also improved significantly (p&lt;0,05) the B content in the soil at 0-30 cm. The B treatments influenced the biochemical composition of the green coffee beans, with a significant (p&lt;0,05) inverse correlation between the B content of the green coffee beans with caffeine, and unsaturated fatty acids (UFAs) mainly, oleic, linoleic, and linolenic acids which are considered negative descriptors of the coffee quality.

The importance of enzymes in the poultry industry is ever increasing because they help to extract as many nutrients as possible from the raw material available and reduce environmental impacts. Therefore, an experiment was conducted to examine the effect of a natural enzyme complex (ASC) on diets low in AME, Ca and P. Ross 308 broilers (n = 900) were fed one of four diets: (1) positive control (PC) with no enzyme added (AME 12.55 MJ/kg, AVPhos 4.8 g/kg and AVCal 9.6 g/kg); (2) negative control (NC) with no enzyme added and down-specified for AME, Ca and P (AME 12.18 MJ/kg, AVPhos 3.3 g/kg, AVCal 8.1 g/kg); (3) negative control plus ASC at 200 g/t; and (4) negative control plus ASC at 400 g/t. Broiler performance, digesta viscosity, tibia mineralization and mineral content were analyzed at d 21. Between d 18 and 20, excreted DM, GE, total nitrogen, Ca, and P were analyzed. ASC at 200 g/t and 400 g/t improved the FCR (p = 0.0014) significantly when compared with that of the NC. There were no significant differences in BW or FI between the treatments. Birds fed ASC at 200 g/t and 400 g/t had significantly improved digesta viscosity (p &lt; 0.0001) compared with that of the PC and NC and had significantly higher excreted DM digestibility (p &lt; 0.01) than the NC and the PC with 400 g/t ASC. ASC inclusion significantly improved P retention (p &lt; 0.0001) compared with that in the PC. Ca retention was significantly increased by 400 g/t ASC compared with that in the PC and NC (p &lt; 0.001). AME was significantly higher (p &lt; 0.0001) for all treatments compared with that in the NC. There were no significant differences between treatments for any of the bone measurements. This study showed that feeding ASC can support the performance of broilers when fed a specification reduced in Ca, P and AME, with the greatest results being seen with the higher inclusion level of ASC.