Carbon nanomaterial is widely used in structural health monitoring due to the advantage of sensitivity and good mechanical properties. This study presents a novel approach employing carbon nanocomposite materials (CNM) to characterize deformation and damage evolution in physical modelling. As the primary measurement method, the CNM is used to investigate the deformation characteristics of a 200-400 m thick sandstone bed at a 1 km deep longwall mine. The sandstone unit is identified as an ultra-thick key stratum (UTKS), with its thicknesses varying across different mining panels of the UTKS. The results of CNM monitoring show that the UTKS remains stable even after a consecutive excavation of 900 m in width. This stability impedes the upward propagation of overlying strata failure, leading to minimal surface subsidence. The study demonstrates the huge potential of CNM in the mining area, which can be useful for investigating material damage in physical modelling studies. The findings suggest that the cumulative extraction width in individual mining areas of the mine should be controlled to avoid a sudden collapse of the UTKS, and that special attention should be paid to where the UTKS's thickness changes substantially. The substantial variation in UTKS thickness significantly impacts the pattern of overburden subsidence.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Pseudolysimachion nakaianum (Ohwi) T.Yamaz. is an endemic species that is an important species in the forest ecosystems of South Korea. This study aimed to develop an in vitro propagation system for P. nakaianum, to enhance the availability of this rare and endemic plant for commercial horticulture and restoration efforts. We utilized cotyledon explants from in vitro germinated seeds and two types of explants (petiole and leaf) from in vitro seedlings to assess the impact of five different cytokinins on adventitious shoot organogenesis in P. nakaianum. The half-strength Murashige and Skoog (MS) medium, supplemented with 10 µM thidiazuron (TDZ) for both cotyledon and petiole explants, yielded the highest shoot induction rates (61.1 ± 9.6% and 26.7 ± 8.8%, respectively) and the greatest number of shoots (3 ± 0.6 and 4.4 ± 0.5, respectively). Responses from leaf explants were variable, with none showing in vitro regeneration. Successfully acclimatized P. nakaianum plantlets in a greenhouse demonstrated normal growth. This protocol outlines an effective method for the direct in vitro regeneration from cotyledon and petiole explants of P. nakaianum, providing valuable information for the conservation of this species.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Lake sediment records are of great importance for understanding the evolution of watershed environments. Various studies have been carried out to constrain the depositional ages of lake sediments and examine their physical, chemical, and biological characteristics, aiming to construct historical vegetation, environment and climate patterns in Chinese lake watersheds. In this study, we obtained relevant literature on lake sediment records by searching the key word 'age-depth' from the databases – Web of Science and China National Knowledge Infrastructure (CNKI, the largest Chinese academic database). We analyzed the literature based on its type (published in a Chinese/English journal or as a Master’s/PhD thesis), period of publication, journal (if published in a journal), key authors, study area, dating scale, and main aims. The results suggest that the lakes in the plateau regions are the most popular research topic typically covering 100–200 years (short-term) and 500–30,000 years (long-term). The literature focuses on a wide range of topics, from past environmental evolution in the watershed to lake ecology, and provides a solid foundation for better understanding regional climate change and the preservation of lake environments and ecosystems. In the future, resulting data from environmental reconstruction with lake sediments will be needed to integrate with emerging information processing technologies (e.g., artificial intelligence and meta-analysis), to disentangle the complex interplay between Earth surface processes and global climate change; furthermore, strengthening interdisciplinary collaboration will deepen our comprehension of man-land relationship and promote the sustainable management of lake ecosystems in the context of global climate change.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

A Berry geometrical phase is identified in a strongly metastable system containing dynamically responsive clathrate hydrate structures within a crystal-fluid material. High energy degeneracy in the associated chemistry produces local stability and false vacuum conditions that lead to non-extensive and non-additive contributions in the fundamental thermodynamic relation. Application of Ginzburg-Landau theory and the scaling laws reveals a coherence length and a penetration depth for a macro-scale dual superconductor. The coherence length determines non-extensive volume changes whilst its inverse gives the Higgs mass. The penetration depth determines the extent of QCD vacuum suppression whilst its inverse gives the vector boson mass together with indirect manifestation as non-additive hyperbolic curvature. Simultaneous emergence of the Ginzburg-Landau superconducting phase transition is consistent with gauge-invariant coupling of the scalar field to the Yang-Mills action in QCD. The discovery of an energy gap in the gradient energy term of the system Lagrangian is associated with a critical correlation length revealed in the transition from a gapped to a gapless superconducting state. Together with the emergence and absorption of the Higgs-like scalar field, a mechanism for describing a renormalized QCD mass gap arises.

Conductive nanocomposites play a significant role in tissue engineering by providing a platform to support cell growth, tissue regeneration, and electrical stimulation. In this present study, a set of electroconductive nanocomposite hydrogels based on gelatin (G), chitosan (CH) and conductive carbon black (CB) was synthesized with the aim to develop novel biomaterials for tissue regeneration application. Incorporation of conductive carbon black (10, 15 and 20 wt %) significantly improved electrical conductivity and enhanced mechanical properties with the increased CB content. We employed an oversimplified unidirectional freezing technique to impart anisotropic morphology with interconnected porous architecture. An investigation into whether any anisotropic morphology affects the mechanical properties of hydrogel was conducted by performing compression and cyclic compression tests in each direction parallel and perpendicular to macroporous channels. Interestingly, nanocomposite with 10 % CB produced both anisotropic morphology and mechanical property, whereas anisotropic pore morphology diminished at higher CB concentration (15 and 20 %) imparting denser texture. Collectively, the nanocomposite hydrogels showed great structural stability as well as good mechanical stability and reversibility. Under repeated compressive cyclic at 50 % deformation, the nanocomposite hydrogels showed preconditioning, characteristic hysteresis, nonlinear elasticity, and toughness. Overall, the collective mechanical behavior resembled the mechanics of soft tissues. Electrical impedance associated to the hydrogels was studied in terms of modulus and phase in dry and wet condition. The electrical properties conducted in wet conditions, which is more physiologically relevant, showed low impedance at high frequencies due to capacitive currents. Overall, impedance of the nanocomposite hydrogels decreased with increased CB concentrations. These gelatin-chitosan–carbon black nanocomposite hydrogels show great promise for use as conducting substrates for the growth of electro-responsive cells in tissue engineering.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Ultralong carbon nanotubes (UCNTs) are highly demanded for nanocomposites applications because of their magnificent physical and chemical properties. UCNTs are synthesized by catalytic chemical vapor deposition (CCVD) method and, before using as fillers in nanocomposites, should be purified from residual catalyst and non-CNT particles without significant destruction or scissoring of UCNTs. The role of water vapor for purification of UCNTs is investigated, the importance of water assistance in this process is confirmed. It was shown that wet air treatment of products of UCNTs CCVD synthesis under mild conditions can be used to decrease sufficiently residual catalyst content without significant carbon losses in comparison with the results obtained with dry air, while the residual iron content was shown to influence heavily on the subsequent oxidation of different forms of carbons, including UCNTs. The increasing of D/G ratio of Raman spectra after wet air treatment of products of UCNTs CCVD synthesis makes it possible to conclude that iron catalyst particles transform into iron oxides and hydroxides that caused inner structural strains and destruction of carbon shells improving removal of the catalyst particles by subsequent acid treatment. UCNTs purification with water assistance can be used to develop economically and ecologically friendly methods for obtaining fillers for nanocomposites of different applications.

The imperative to achieve carbon neutrality has driven significant advancements in the construction sector, particularly in the production and utilization of building materials. This paper explores innovative strategies and practices designed to reduce the carbon footprint of construction materials, with a focus on both the production processes and the application of sustainable materials. Key innovations include the development of low-carbon and carbon-negative materials, the integration of renewable energy sources in production, and the implementation of advanced recycling technologies. Case studies of successful projects demonstrate how these strategies can be applied in real-world scenarios, highlighting both the benefits and challenges encountered. The analysis also delves into the technical and economic aspects of these innovations, addressing the barriers to their widespread adoption and proposing solutions to overcome these challenges. Through a comprehensive examination of current practices and future trends, this paper aims to provide a roadmap for the construction industry to achieve carbon neutrality, contributing to broader climate change mitigation efforts and fostering a more sustainable built environment.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

Soot combustion experiments with 5%O2/He were conducted using model soot, and four distinct compositions of CexPr1-xO2-δ oxides were prepared, varying nominal cerium com-positions (x=0, 0.2, 0.3, and 1). The catalyst samples were comprehensively characterized using techniques such as XRD, Raman spectroscopy, HR-TEM, N2 adsorption at −196 °C, XPS, O2-TPD, H2-TPR, and work function measurements. The Pr-rich compositions, rang-ing from Ce0.3Pr0.7O2-δ to PrO2-δ, resulted in a significant increase in the total evolved O2 amounts and enhanced catalyst reducibility. However, a decrease in textural properties of the catalysts was noted, being particularly important for the pure praseodymia under the synthesis route conducted. The catalytic activity was investigated under two contact modes of mixing between soot and catalyst: loose and tight. The results revealed that the catalytic performance is associated with the surface contact in tight contact mode and with the combination of surface/subsurface/bulk oxygen mobility and the BET surface ar-ea in loose contact mode. Notably, the T10 and T50 parameters were achieved at much lower temperatures than the uncatalyzed soot combustion, even under loose contact conditions. Specifically, the 50% conversion was achieved at 511℃ and 538℃ for Ce0.3Pr0.7O2 and Ce0.2Pr0.8O2, respectively. While no direct correlation between catalytic activity and work function was observed a significant relationship emerges between work function values and the formation of oxy-gen vacancies, whatever the conditions used for these measurements. On the other hand, the ability to generate a high population of oxygen vacancies at low temperatures, rather than the direct activation of gas-phase O2, influences the catalytic performance of Pr-doped ceria catalysts, highlighting the importance of surface/subsurface oxygen vacancy generation, which was the parameter which showed better correlation with the catalytic activity, whatever the soot conversion value or the mode of contact considered.

The stepwise hydrogenation of the C=C bond and C=O group of acrolein on Au₃ and Au₅ model systems is investigated using the density functional theory(DFT) PW91 functional. Our results show that the C=C hydrogenation is more favorable than that of C=O bond on Au₃ with the barriers of the rate-determining step being 0.35 and 0.62 eV respectively. On the other hand, the C=O reduction is preferred over the hydrogenation of the C=C bond on Au₅. The corresponding barriers of the rate-determining steps are 0.45 and 0.54 eV, respectively. This demonstrated that the second hydrogenation step controls the reaction on both Au₃ and Au₅ for C=O and C=C hydrogenation and the C=O hydrogenation on Au₅ is preferred over the hydrogenation of the C=C bond, which is helpful to address the reactivity of small size-selected supported gold clusters.

High-performance anodes are contributed to nanostructure of transition metal oxides for rechargeable Li-ion batteries (LIBs). In this work, we report the fabrication of high-performance anode materials for lithium-ion batteries, MnO2 nanotube directly grown into fabrics of carbon nanofibers, the MnO2/Carbon nanofibers (CNFs) were investigated by X-ray diffraction, scanning and transmission electron microscopies. When tested as the anode material in LIBs, the MnO2/CNFs exhibit superior performance and excellent long cycling performance with a reversible capacity of 835 mA h g-1 at 0.1 A g-1 after the 133 th cycle, a high initial specific capacity of 1094 mA h g-1 at a current density of 0.1 A g-1. The MnO2/CNFs demonstrates notable specific capacities, specifically, with a coulombic efficiency of 99.5 %, both stability and capacity are conspicuously above literature data. These impressive results indicate that MnO2/CNFs has great potential for high-energy and high-power energy storage applications.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Aiming at the damage detection and continuous monitoring of high efficiency composite structure, the method of carbon nano sensor embeded in the 3-D braided composite material specimen was put forward and the method of damage location for 3-D braided composite material was described. In this paper, the mechanical and electrical characteristics of carbon nano-fiber were analyzed. Considering the massive data of the health monitoring of composite processing, to ensure that the system has good real-time performance, quaternary matrix Singular Value Decomposition algorithm is proposed to simplify data and improve the efficiency of the algorithm. The existence of injury is determined and the damage location is calculated by comparing with key features of healthy specimen. Experimental results prove the method is feasible and effective.

The study of the tribological behavior of the braking system in auto vehicles requires knowing the characteristics of the material in contact and, in the work process, for the friction pair, brake disc-pads. Materials structural analysis is necessary because the wear process depends on the friction pair chemical composition, and brake disk-pads, respectively on the work process parameters (pressing force, rotational speed, traffic conditions, etc.). The material of the brake discs is generally the same gray cast iron, but the brake pads can be semi-metallic (particles of steel, copper, brass, and graphite, all united with a special resin), organic materials (particles of rubber, glass, and kevlar all joined with the help of a resin), composite materials that contain different constituents and ceramic materials (rarely have small copper particles). Therefore, the purpose of the paper is to know the crystalline structure and the mechanical properties of the brake pad materials, through specific studies and analyses, with important implications on the friction and wear behavior.

TiO2-based building materials have air purification, auto-cleaning and sterilization functions, and these innovative green building materials have great potential for energy-saving and emission reduction applications in the future. However, there are still great challenges in improving photocatalytic efficiency and stability from laboratory to practical applications. In recent years, researchers have done a lot of work to improve the efficiency and stability of TiO2-based building materials. This paper briefly discussed the air purification principle by photocatalytic building, and the preparation techniques of TiO2-based building materials and the strategies to improve the efficiency of TiO2. Moreover, this paper has outlined the key factors that affect the photocatalytic building performance in practical applications, and analyzed the limitations and future development trends. Finally, we proposed some suggestions for further research on photocatalytic buildings and its application in practice, aiming to provide an efficient reference for developing highly efficient and stable photocatalytic building materials. The aim of this paper is to provide effective guidance for the application of TiO2-based photo-catalysts in the field of green buildings, helping to develop more efficient and stable low-carbon buildings for the development of sustainable cities.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

The results of the investigation showed that second-order kinetics govern the adsorption process, and the corresponding rate constants were found. To evaluate the parameters related to the adsorption process, the adsorption equilibrium was examined using a variety of mathematical models, such as the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models. The Langmuir isotherm was found to be the best appropriate among all models for describing the adsorption of Cu2+ and Ni2+ ions using bio-nanocomposite beads. The positive values of ΔH° indicate that the adsorption is physical and endothermic, in agreement with experimental results. The negative value of ∆G° shows that the adsorption process is spontaneous. Positive ΔS° values indicate increased randomness at the solid/liquid interface, during adsorption of Cu2+ and Ni2+ cations onto the engineered bio-nanocomposite. The maximum adsorbed amounts of metal ions by the bio-nanocomposite used were 370.37 mg/g for Ni2+ and 454.54 mg/g for Cu2+ from single system. For the binary system, according to the Langmuir isotherm, the maximum adsorbed amounts of Ni2+ and Cu2+ were 357.14 mg/g and 370,37 mg/g, respectively. There is proof that Alginate-Moroccan clay bio-nanocomposites can serve as a different, less expensive source of sorbents for the removal of metal ions from single and binary systems.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Time and cost-efficient techniques are essential to avoid extra conventional experimental studies with large date-set to characterize the mechanical properties of composite materials. Correlation between the structural performance and mechanical properties could be captured through the efficient predictive models. Several ensembled Machine Learning (ML) methods were implemented in this study, to materially characterize carbon nanotube (CNT)-reinforced cement-based composites. Proposed models were compared with each other to represent the accuracy of each method. The Flexural and Compressive Strength (target values) of CNT reinforced composites were predicted based on the data-rich framework provided in previous experimental investigations. These data were utilized for training of the proposed models by employing SciKit-Learn library in Python, followed by hyper-parameter tuning and k-fold cross-validation method for obtaining an efficient model to predict the target values. Random Forest (RF) and Gradient Boosting Machine (GBM) were developed for this purpose. The findings of this study would be useful for prospective composite designers in case of sufficient experimental data availability for ML model training.

Kamchatka berries (Lonicera caerulea L.) are known for their high content of phenolic compounds or vitamins, which is reflected in their antibacterial, detoxifying and anti-inflammatory properties. They are used in the production of jams, juices, wines and as natural dye. A bioferment was prepared from the pomace of the Kamchatka berry varieties Aurora and Indigo Gem and the strains Saccharomyces cerevisiae and Lacticaseibacillus paracasei, which was used to prepare a cosmetic preparation with a concentration of 5% in accordance with the guidelines of the COSMOS certification body. Conducted physico-chemical and organoleptic analyses and bioactive profile characterisation (UHPLC-DAD and UHPLC-ESI-MS/MS). The results showed that the presence of caffeic acid 4.47 ± 0.07 mg/100g was detected after fermentation of Kamchatka berry pomace. Vitamin C content increased by 141% after fermentation of Kamchatka berry pomace. The results of stability tests showed that in the process of physicochemical analysis of cosmetic preparation with bioferment of Kamchatka berry pomace the pH should oscillate in the range of 4.38-4.76 ± 0.01. Stability tests showed that the cosmetic should be protected from high temperatures and UV radiation and proved that the product is stable under changing conditions, resulting in lower transport and storage costs.

This study introduces a novel nanocomposite coating composed of PANI/CeO2 nanocomposite films, aimed at addressing corrosion protection needs. Analysis through FTIR spectra and XRD patterns confirms the successful formation of the nanocomposite films. Notably, the PANI/CeO2 nanocomposite films exhibit a hydrophilic nature. The bandgap energy of the PANI composite film measures at 3.74 eV, while the introduction of CeO2 NPs into the PANI matrix reduces the bandgap energy to 3.67 eV. Furthermore, the electrical conductivity of the PANI composite film is observed to be 0.40 S.cm-1, with the incorporation of CeO2 NPs leading to an increase in electrical conductivity to 1.07 S.cm-1. To evaluate its efficacy, electrochemical measurements were conducted to assess the corrosion protection performance. Results indicate a high protection efficiency of 92.25% for the PANI/CeO2 nanocomposite film.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

Microplastics (MPs) are a critical environmental issue, with impacts ranging from ecosystem contamination to health risks through bioaccumulation. This review addresses the inefficacy of traditional water treatments in removing MPs and proposes photodegradation, particularly via nanomaterial-enhanced photocatalysts, as a solution. Utilizing their unique properties like large surface area and tunable bandgap, nanomaterials significantly improve degradation efficiency. Different strategies for photocatalysts modification to improve photocatalytic performance are thoroughly summarized, with the particular emphasis on element doping and heterojunction construction. Furthermore, this review thoroughly summarizes the possible fundamental mechanisms driving photodegradation of microplastics facilitated by nanomaterials, with a focus on processes like free radical formation and singlet oxygen oxidation. By clearly elucidating these strategies and mechanisms, this review aims to provide valuable insights and inspire further progress in microplastic photodegradation.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Hydrogels can be considered as mimics of extracellular matrix (ECM).Cytoskeleton through integrins is connected with ECM and cytoskeleton tension depends on ECM stiffness.A number of age-related diseases depend on cellular processes related with cytoskeleton function.Some examples of cancer initiation and progression and heart disease in relationship with ECM stiffness has been analysed.Incorporation of rigid particles in ECM can increase ECM stifness and to promote formation of internal residual stresses. Water migration, changes of water binding energy to biomactomolecules, changes of the state of water from tightly bound water to free and loosely bound water changes stiffness of ECM. Risks related with rigid particles incorporation into ECM have been also iscussed.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Infectious diabetic wounds can result in severe injuries or even death. Biocompatible wound dressings offer one of the best ways to treat these wounds, but creating a dressing with suitable hydrophilicity and biodegradation rate can be challenging. To address this issue, we used the electrospinning method to create a wound dressing composed of poly(glycerol sebacate) (PGS) and gelatin (Gel). We dissolved the PGS and Gel in acetic acid (75 v/v%) and added EDC/NHS solution as a crosslinking agent. Our measurements revealed that the scaffolds' fiber diameter ranged from 180.2 to 370.6 nm, and all the scaffolds had porosity percentages above 70%, making them suitable for wound healing applications. Additionally, we observed a significant decrease (p < 0.05) in the contact angle from 110.8° ± 4.3° for PGS to 54.9° ± 2.1° for PGS/Gel scaffolds, indicating an improvement in hydrophilicity of the blend scaffold. Furthermore, our cell viability evaluations demonstrated a significant increase (p < 0.05) in cultured cell growth and proliferation on the scaffolds during the culture time. Our findings suggest that the PGS/Gel scaffold has potential for wound healing applications.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

Nanoparticles of graphene and carbon nanotubes are attractive materials for improvement of mechanical and barrier properties and functionality of biodegradable polymers for food packaging applications. However, the increase of the manufacture and consumption increases the probability of exposure of human and environment to such nanomaterials, this rising questions about the risks of nanomaterials since they can be toxic. For a risk assessment, it is crucial to know whether airborne nanoparticles of graphene and carbon nanotubes can be released from nanocomposites into the environment at their end-life, or they remain embedded in the matrix. In this work the release of graphene and carbon nanotubes from the poly(lactic) acid nanocomposite films were studied for the scenarios of: (i) biodegradation of matrix polymer at the disposal of wastes; and (ii) combustion and fire of nanocomposite wastes. Thermogravimetric analysis in air atmosphere, TEM, AFM and SEM were used to verify the release of nanoparticles from nanocomposite films. The three factors model was applied for the quantitative and qualitative risk assessment to the release of graphene and carbon nanotubes from nanocomposite wastes for these scenarios. Safety concern is discussed in respect to the existing regulations for nanowastes stream.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

In this study, an attempt was made to investigate the Kenya case of multivariate causality of carbon dioxide emissions by employing a time series data spanning from 1961-2011 using the ARDL method of cointegration analysis. The long-run elasticities show that, a 1% increase in financial development increases carbon dioxide emissions by 0.28%, a 1% increase in GDP per capita increases carbon dioxide emissions by 1.32% and a 1% increase in urbanization decreases carbon dioxide emissions by 1.14%. There was a unidirectional causality running from financial development, food production index, GDP per capita, industrialization and urbanization to carbon dioxide emissions. The innovation accounting shows that 20% of future shocks in carbon dioxide emissions are due to fluctuations in financial development, 9% of future shocks in financial development are due to fluctuations urbanization and 22% of future shocks in food production index are due to fluctuations in carbon dioxide emissions.

Li4Ti5O12 (LTO) exhibits zero-strain behavior, exceptional cycle stability, low cost, and high safety. However, it is still low in electronic and ionic conductivity. Incorporating Sn into LTO materials can increase electronic conductivity and specific capacity. However, Sn still experiences volumetric expansion during the charging/discharging process. Adding activated carbon (AC) into the LTO/Sn composite can help improve the expansion resistance and electronic conductivity. In this work, the AC was first synthesized from charcoals through the carbon activation process and mixed with LTO precursors through the sol-hydrothermal method followed by mixing with Sn through the mechanochemical process to produce LTO@AC/Sn composites. The Sn content was fixed at 15 wt.%, while the AC contents were varied at 1 wt.%, 3 wt.%, and 5 wt.%. The AC specific surface area is increased by more than 100% compared to the non-activated one. The best effects of AC on grain morphology and distribution were found in the LTO/Sn contained 3 wt.% of AC, leading to transfer resistance, ohmic resistance, specific capacity, and coulombic efficiency were found to be 48.1 Ω, 8.5 Ω, 138 mAhg-1, and near 100%, respectively. The result suggests that the LTO@AC/Sn could be a favorable anode active material in lithium-ion batteries.

Production of wastewater related to the oil and gas industries is increasing over the years. The compounds found in industrial wastewater typically show high toxicity, and in this way, they have become a primary environmental concern. Several techniques have been applied in industrial effluents remediation. In spite of the efforts, these techniques are yet ineffective to treat oily wastewater before it can be discharged safely to the environment. Membrane technology is an attractive approach to treat oily wastewater. This is dedicated to the immobilisation of TiO2 nanoparticles on poly (vinylidene fluoride–trifluoro ethylene) (PVDF-TrFE) porous matrix by solvent casting. Membranes with interconnected pores with an average diameter of 60 micrometres and the contact angle of 97°, decorated with TiO2 nanoparticles, are obtained. The degradation of oily wastewater demonstrated the remarkable photocatalytic efficiency of the nanocomposite membranes: under sunlight irradiation for 7 hours, colourless water was obtained. These results show the suitability of TiO2/P(VDF–TrFE) nanocomposite for photocatalytic applications for oily wastewater remediation.

Reducing GHG emissions is a crucial challenge in urban areas, characterized by high energy consumption and reduced exposure to nature. In this context, the urban green system could play a pivotal role. In the literature, scholars analyzed both the ability of species-specific and layout-specific green infrastructures to increase carbon sequestration and the best location sites of new green infrastructures, to increase the provision of overall ecosystem services. There is a lack of studies helping green urban planners and designers choose where and which green infrastructure to implement, based on vegetation species-specific performance and local carbon emissions of city components. This paper uses tree inventory data from a medium-sized city in central Italy (Perugia) to develop a spatial analysis of the urban parks' performance in carbon sequestration. Then, the method evaluates the carbon emission of a public city building to generate a spatialized balance between buildings’ demand and trees’ supply, to support local decisions about the best locations for new green infrastructures and the choice between species. The paper contributes to GIS-based tools that vary the recommended location sites and species for new green infrastructures based on the demanded ecosystem service.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

Despite saltmarshes being considered as nature-based solutions (NbS) towards climate change mitigation, India’s saltmarsh ecosystems are least studied. This study quantifies the seasonal variation in carbon stocks mono-specific saltmarsh species (Porteresia coarctata) and its potential to play an important role in India’s climate change mitigation plans. Seasonal (pre-and post-monsoon) sampling of P. coarctata surface water, biomass and 30 cm sediment core was collected across four locations on the east coast of India to quantify sediment dry bulk density (DBD), organic matter (OM%), organic carbon (Corg%), Corg stocks of sediment and biomass, total carbon (C%) and nitrogen (N%) and stable isotopes of δ13C and δ15N. In general, the sediment DBD, OM and Corg of P. coarctata meadows was higher in post-monsoon and was influenced by salinity and pH changes. Isotope (δ¹³C) modelling of various sediment C sources suggested, particulate organic matter (POM) contribution was highest (0.04-0.79%) followed by P. coarctata (0.01–052%) and other macrophytes across our study locations. The seasonal variation of δ¹³C showed increased contribution of marine derived particulate and dissolved organic matter into P. coarctata meadows in post-monsoon season. Heavier δ¹⁵N values were observed in post-monsoon season suggesting anthropogenic input, that was utilized by P. coarctata to increase its above and below-ground biomass and shoot density. The combined ecosystem (30 cm sediment + biomass) Corg stocks of P. coarctata was 1.7-fold higher in post-monsoon (4021.20± 917 Mg C) compared to pre-monsoon (2297.36 ±647 Mg C) season among the four locations with a sediment Corg contribution >70%. Based on the International Panel for Climate Change Tier II assessment the P. coarctata meadows (443 ha) can help in avoiding the pre and post-monsoon emissions of 8431.34 and 14757.84 Mg CO₂ respectively. The combined price of the total CO₂ equivalent stored in P. coarctata meadows in pre- and post-monsoon is US$ 14.50 and US$ 25.38 million respectively. Further studies quantifying the NbS potential of P. coarctata mono-specific and mixed meadows of India’s coast is needed along with integration of saltmarsh ecosystems into India’s National Action Plan on Climate Change.

This research aimed to investigate the relationship between climate policy uncertainty (CPU), clean energy (ENERGY), carbon emission allowance prices (CARBON), and Bitcoin returns (BTC) for the period from August 2012 to August 2022. The empirical analysis strategies utilized in this study included the Fourier Bootstrap ARDL long-term coefficient estimator, Fourier Granger Causality, and Fourier Toda Yamamoto Causality methods. Following the confirmation of cointegration among the variables, we observed a positive relationship between BTC and CARBON, a positive relationship between BTC and CPU, and a negative relationship between BTC and ENERGY. In terms of causal associations, we identified one-way causality running from CARBON to BTC, BTC to CPU, and BTC to the ENERGY variable. The study underscores the potential benefits and revenue opportunities for investors seeking diversified investment strategies in light of climate change concerns. Furthermore, it suggests actionable strategies for policymakers, such as implementing carbon taxes and educational campaigns, to foster a transition towards clean energy sources within the cryptocurrency mining sector and thereby mitigate environmental impacts.

This study explored the effects of cryogenic treatment on the microstructure, hardness, and wear-resistance of diamond-like carbon (DLC) by cryogenically treating NAK 80 mold steel coated with DLC. Raman spectroscopy analyzed the structure of the DLC film. Nanoindenter analyzed the hardness and Young’s modulus of the film, and their relationship determined the wear resistance. Wear test assessed the wear rate and friction coefficient of the DLC film. The results showed that cryogenic treatment increased the rate of carbide precipitation and refined the grain structure. Raman spectroscopy indicated that the Raman intensity rate (I_D/I_G) of treated DLC films was smaller than those without cryogenic treatment. When the sp3 bond increased, the hardness and wear-resistance of the DLC film also increased.

LiFePO4 (LFP) has undergone extensive research and is a promising cathode material for Li-ion batteries. The high interest is due to its low raw material cost, good electrochemical stability, and high-capacity retention. However, poor electronic conductivity and a low Li+ diffusion rate decrease its electrochemical reactivity, especially at fast charge/discharge rates. In this work, the volumetric energy density of lithium-ion batteries is successfully increased by using different amounts of conductive carbon (Super P) in the active material content. The particle size and morphology of the electrode material samples are studied using field emission scanning electron microscopy and dynamic light scattering. Two-point-probe DC measurements and adhesive force tests are used to determine the conductivity and evaluate adhesion for the positive electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge/discharge tests are used to analyze the electrochemical properties of the battery. The samples containing 88% LFP, 5.5% Super P and 6.5% PVDF perform best, with discharge capacities reaching 169.8 mAhg-1 at 0.1C, and they can also manage charging/discharging of 5C. EIS indicates that this combination produces the lowest charge-transfer impedance (67 Ω) and the highest Li+ ion diffusion coefficient (5.76 x 10-14 cm2s-1).

Sulfonated carbon was used as an efficient and reusable heterogeneous solid acid catalyst for the synthesis of biodiesel via esterification of oleic acid with methanol under high voltage conditions. Using an inexpensive and reusable catalyst, environmental benignity, excellent yields in short times, synthesis in atmospheric pressure and low temperature conditions are some of the important features of this protocol. In the final results were confirmed by GC.

Compressed carbon dioxide energy storage (CCES) offers several benefits over other existing energy storage systems, including ease of liquefaction, high energy storage density, and environmental friendliness. As a result, the research progress, economic and technological feasibility, and system operation of the CCES system are all discussed in depth in this study. The system evaluation method is summarized and the compressed carbon dioxide storage is analyzed, and the performance optimization direction of the compressed carbon dioxide energy storage technology is discussed. When the overall performance of a transcritical CCES system, a supercritical CCES system and a liquid CCES system are compared, it is discovered that the supercritical CCES system has better thermodynamic characteristics and a simpler system configuration, making it suitable for large-scale development and use. The goal of the CCES system's future development is to create a design with an optimum compression and expansion ratio, a more precise analysis and system model, and multi-field coupling. This review's discussion serves as a guide for the best design and use of the CCES system.

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

Mechanochemical technology is developing rapidly, judging by the scientific information in both basic and applied studies. However, many issues and points of view remain to be discussed. This review presents some new key issues for the optimization of mechanochemical processes in theoretical and practical aspects. Emphasis is placed on powder technology aspects, which are not always discussed compared to functional or microscopic viewpoints. The transfer of chemical species across the interparticle interface between organic and inorganic species during the mechanosynthesis of nanocomposite oxides offers many new possibilities, which are discussed here in detail. Since all material transport is preceded by charge transfer, its driving force has been searched for using terminology beyond the well-established electrochemical ones. The role of organic compounds during the whole process is emphasized, regardless of their survival in the final product. The similarity with the pharmaceutical phenomena is pointed out, although its mentality is very different from that of the synthesis of nanocomposites. Not only for the rational amorphization of the active pharmaceutical ingredient, but also for the stabilization of molecular dispersion states with the participation of excipients are discussed. The effects of liquids, either added or formed by mechanochemical auto-liquefaction, are presented with reference to the comparison between wet and dry grinding. Finally, mechanisms of apparent stabilization of mechanically activated states of products are elucidated to investigate the practical applicability of mechanochemically synthesized products

We address Multi-Wall Carbon NanoTubes (MWCNTs) for structural health monitoring in adhesive bonds such as in building structures. MWCNT-loaded composites are employed to sense strain changes under tension load using an AC impedance measurement setup. Different weight percentages of 1, 1.5, 2 and 3 wt.% MWCNT are added to the base epoxy resin using different dispersion times, i.e. 5, 10 and 15 minutes. The equivalent parallel resistance of the specimens is measured by applying an alternating voltage at different frequencies. To determine the mechanical as well as sensory properties, the specimens are subjected to a tensile test with concurrent impedance measurement. Using alternating voltage, a higher sensitivity of the impedance reading can be achieved. Employing these sensors in buildings and combining the readings of a network of such devices can significantly improve the buildings’ safety. Additionally, networks of such sensors can be used to identify necessary maintenance actions and locations.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

Retrospective information about the climate system and plant ecophysiology are key inputs in climate and Earth system modelling. Dendrochronology provides such information with large spatiotemporal coverage, and stable carbon isotope (¹³C/¹²C) analysis across tree-ring series is among the most advanced dendrochronological tools. For the past seventy years, this analysis was performed on whole molecules, and, to this day, ¹³C/¹²C variation is attributed to ¹³C discrimination during CO₂ diffusion into leaves and assimilation by rubisco. By contrast, ¹³C discrimination by post-rubisco processes is presumed constant. Here, recently reported results on the first dataset of intramolecular ¹³C discrimination in tree rings were synthesised by variance component analysis. The emerging picture is not consistent with the classical (DR-discrimination-centred) concepts and practices of carbon-isotope dendrochronology. Specifically, leaf and stem post-rubisco discrimination each account for more variation in the data than diffusion-rubisco discrimination, i.e., post-rubisco discrimination is not constant. Furthermore, diffusion-rubisco discrimination is used widely as proxy of leaf intrinsic water-use efficiency (iWUE), a key determinant in the responses of global biogeochemical cycles to climate change. However, since diffusion-rubisco discrimination is a small component of the total data variance, whole-molecule analysis yields confounded iWUE estimates, yet intramolecular analysis will likely offer solutions. Lastly, all currently observed ¹³C/¹²C-climate relationships are attributed to diffusion-rubisco discrimination. However, here, relationships with temperature and radiation derive from leaf-level post-rubisco discrimination while relationships with precipitation derive from stem-level post-rubisco discrimination. That said, advances in mass spectrometry may soon make intramolecular ¹³C/¹²C analysis broadly available taking carbon-isotope dendrochronology to the next level.

This article utilized electrodeposition technology to fabricate Zn and Zn-Y₂O₃-Al₂O₃ composite coatings on Q235 steel plates. The composite coatings were obtained by adding Y₂O₃/Al₂O₃ nanoparticles (0, 5, 10, and 15 g/L) to acidic chloride solutions. This study then examined the impact of these nanoparticles on the microstructure, morphology, microhardness, hydrophobicity, and corrosion resistance of the composite coatings. The results indicate that the addition of the nanoparticles increased the nucleation sites on the surface of the coating, thereby refining the grain size and reducing the roughness of the coating surface. When 10g/L of Y₂O₃ and 10g/L of Al₂O₃ nanoparticles were added, the hardness of the composite coating (369 Hv) was 2.49 times higher than that of the pure Zn coating (148 Hv), which was attributed to the dispersion strengthening and grain refinement effects of the nanoparticles. The corrosion resistance of the Zn and Zn-Y₂O₃-Al₂O₃ composite coatings was studied using linear sweep voltammetry and AC impedance spectroscopy. The addition of the nanoparticles improved the corrosion resistance of the composite coating, and the composite coating prepared in an electrolyte containing 10 g/L of Y₂O₃ and 10 g/L of Al₂O₃ nanoparticles exhibited the best corrosion resistance. Meanwhile, the composite coating exhibited good hydrophobicity, with a contact angle of 120.9°, 1.94 times that of the pure Zn coating (62.2°). The Zn-Y₂O₃-Al₂O₃ nanocomposite coating material has significant potential advantages in the field of steel corrosion.

The compatibility of graphene or graphene oxide with its dispersion medium (polymer) plays a critical role in the formation nanocomposite materials with significant property improvements. Environmentally friendly miniemulsion polymerization, which allows a formation of nanoencapsulation in an aqueous phase and high molecular weight polymer/composite production is one promising method. In this study, we screened a series of amphiphilic modifiers and found that the quaternary ammonium (ar-vinyl benzyl) trimethyl ammonium chloride (VBTAC) pending carbon double bonds could effectively modify the graphene oxide (GO) to be compatible with the organophilic monomer. After that, free radical miniemulsion polymerization could successfully synthesize stable latex of exfoliated poly (methyl methacrylate) (PMMA)/ GO nanocomposite. The final latex had an extended storage life and a relatively uniform particle size distribution. X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) analysis of this latex and its films indicated successful encapsulation of exfoliated nano-dimensional graphene oxide inside a polymer matrix.

Successful fertilization treatments targeted to improve stand productivity while reducing operational complexities and cost depend on a clear understanding of soil nutrient availability under varying environmental conditions. Soil nutrient data collected from 154 forest sites throughout the Inland Northwest, USA were analyzed to examine soil nutrient characteristics on different geologic soil parent materials and to rank soil fertility. Results show that soil parent material explains significant differences in soil nutrient availability. Soils developed from volcanic rocks have the highest CEC and are relatively high in P, K, S, Mg, Cu, Ca, and B, but generally poor in N. Forest soils developed from plutonic rocks exhibit the lowest CEC and are low in N, S, K, Mg, Cu, and Ca, but higher in P. Some soils located on mixed glacial till are low only in K, Cu, Mg, and Ca, but many glacial soils are relatively rich in other nutrients, albeit the second lowest CEC. Soils developed from metasedimentary and sedimentary rocks are among those with lowest soil nutrient availability for P and B. Sulfur was found to have the highest concentrations in metasedimentary influenced soils and the least in sedimentary derived soils. Our results should be useful in designing site-specific fertilizer and nutrient management prescriptions for forest stands growing on soils developed from these major geologies within the Inland Northwest region of the United States.

We report a self-assembly synthesis of silicon nanoparticles/nitrogen-doped reduced graphene oxide/ carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for rechargeable lithium-ion batteries (LIB) through the electrostatic attraction between amino and carboxyl groups. Nitrogen atoms generate a large number of vacancies or defects on the graphite plane, providing additional transmission channels for the diffusion of lithium ions, and improving the conductivity of the electrode. Carbon nanofiber (CNF) can help maintain the stability of the electrode structure and prevent silicon nanoparticles from falling off the electrode, prevent silicon nanoparticles from being directly exposed to the electrolyte, and can form a stable solid electrolyte interface (SEI) film. The three-dimensional conductive structure composed of Si, nitrogen atom-doped reduced graphene oxide (N-doped rGO), and CNF can effectively buffer the volume changes of silicon nanoparticles, shorten the transmission distance of lithium ions (Li+) and electrons, and make the electrode have good conductivity and stability in mechanical properties. In addition, compared with the Si@N-doped rGO and Si/rGO/CNF composite electrode, the Si@N-doped rGO/CNF composite electrode shows good cycle performance and rate capability, and its reversible specific capacity can reach 1418.8 mAh/g. The capacity retention rate is 64.7%, and the coulomb efficiency is 95%.

Introduction: Among the many factors that may limit effective wound healing in patients with chronic ulcers, bacterial infection and poor cell recruitment are primary causes that contribute to prolonged healing. Thus, a novel strategy that aims to prevent bacterial infection within the wound, while at the same time providing structural scaffolding that promotes endogenous tissue repair, would be of great interest. Here, we developed a thermo-sensitive silver nanoparticle hydrogel composite as an antibacterial nutritional scaffold for the wound that contains all nutrients required for cell growth while preventing bacterial infection with the ability to fill up all the cavities and void areas in wounds regardless of their geometry. Methods: Silver nanoparticles (AgNPs) were synthesized by chemical reduction. After characterization, silver hydrogel nanocomposite was developed by reconstitution of collagen-based hydrogel powder in a nanoparticle suspension of varying AgNPs concentrations (200, 400, and 600 ppm). The antibacterial activity of the formulations was examined in vitro and in vivo in subcutaneous implant infected model. The wound healing efficacy of the hydrogel nanocomposite was also evaluated using a splinted wound model in rats through comparison of clinical wound measurements and histological assessments. Cytocompatibility assay and biochemical analysis of blood at the end of in vivo wound healing study were performed to evaluate the safety of formulations. Results: The synthesized nanoparticles were spherical and stable. While hydrogel alone did not show any bacterial reduction in vitro, the inhibition of bacterial growth was significant in all silver hydrogel nanocomposites compared to controls (p <0.05) and was dose-dependent, with maximum reduction observed in the 600 ppm group (4.56±0.26 LOG CFU/mL, P<0.001). All concentrations of AgNPs hydrogel composites showed significant antibacterial activity in vivo as well (P<0.0001). Treatment of splinted wounds with AgNPs hydrogel composite resulted in faster wound closure and accelerated wound re-epithelialization. The formulations were non-cytotoxic and did not differ significantly in hematological and biochemical factors from the control group in in vivo study. Conclusions: By presenting promising antibacterial and wound healing activity, silver hydrogel nanocomposite offers a safe therapeutic option that can be used as a functional scaffold for an acceleration of wound healing.

New hybrid nanostructured electrodes for supercapacitors made by combination of electrical double layer and faradaic supercapacitors based-nanomaterials within a single hybrid composite has a great potential on expanding the range of use of these devices and increase their electrochemical performance. In this work, we developed several hybrid nanostructured composites with combinations of such types of materials with potential applicability as electrodes in supercapacitors. In particular, these composites were obtained by easy, cost-effective and scalable procedures, and were composed by NiCo2O4 nanocores as the main faradaic-based nanomaterial and either the conductive polymer polyaniline (PANI), multiwall carbon nanotubes (MWCNTs), or reduced graphene oxide (r-GO) as the electrical double layer-based carbonaceous-based nanomaterials in order to enable the combination of both type of energy storage processes within a single nanostructured device. These constructions allowed us to obtain specific capacitance as large as 1760 F/g, 900 F/g and 734 F/g at a current density of 1 A/g for NiCo2O4/PANI, NiCo2O4/MWCNT, and NiCo2O4/r-GO hybrid nanocomposite electrodes, respectively. Besides, the stability of NiCo2O4/MWCNTs and NiCo2O4/r-GO-based electrodes was outstanding, with capacity losses below 10% after long periods of operation (> 500 cycles).

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

Emulsifiers like egg yolk (EY) are necessary for the formation of mayonnaise, which is an oil-in-water type colloid. This study aimed to assess the potential of defatted soybean powder treated with supercritical carbon dioxide (DSF-SC) in enhancing the quality of plant-based may-onnaise as plant-based alternatives gain popularity. This study involved producing DSF-SC and comparing its quality attributes to those of mayonnaise made with varying amounts of control soy flour (CSF), DSF-SC, and EY. It was found that mayonnaise made with DSF-SC, with increased emulsifier quantity, showed better emulsion stability, viscosity, and smaller, more uniform particle size compared with CSF mayonnaise. Additionally, DSF-SC mayonnaise was overall rated higher in sensory evaluation. The addition of approximately 2% DSF-SC positively influenced the emul-sion and sensory properties of the vegan mayonnaise, making DSF-SC a promising plant-based alternative emulsifier for replacing animal ingredients.

Abstract: Efforts for carbon emission reduction have been identified as a major climate change mitigation target in the Paris Agreement. The 26th Conference of Parties to the United Nations Framework Convention on Climate Change highlighted the worldwide effort for cleaner and greener mining, urging the mineral industry to embrace greener operational emissions reduction technologies and strategies. Ghana pledged at the Paris Conference to reduce CO2 emissions by 15% and increase renewable energy share to 10% of the national energy mix. Here the fundamental question is how Ghana’s mining industry can contribute to CO2 emission reduction efforts. This paper investigates barriers to low-carbon emission policy implementation among mining companies in Ghana. The questionnaire survey was conducted among Ghana’s four large-scale gold mining companies. As the sample number of available companies is limited, we used a descriptive analysis to assess the responses. The results show that the companies expressed widely different ways to respond to the issues of cost, a government policy/regulations for carbon emission reduction, and the adoption/acquisition of low-carbon technologies. Those companies that are relatively less prepared for this endeavor emphasized the uncertainties of securing sufficient energy in case of using low-carbon technologies. They also expressed a need for more trained workers to handle low-carbon technologies. All companies agreed with a expected high cost of adopting low-carbon options. There was a communication gap with the relevant government ministry about low-carbon mining options where the government should be able to facilitate the involvement of othe low technology providers, such as solar PV installation.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Polyphenols are the most common organic compounds in wine. They improve both the sensory aspects of wine and human health by activating antioxidant systems. Therefore, there is a great need for a simple, fast and accessible method to determine the polyphenol content of wine. The aim of this study is to characterize polyphenolic compounds in natural wine samples using an electrochemical method and a modified carbon paste electrode with TiO2 nanoparticles. This work is motivated by the promising improvement of the sensing properties of a TiO2 nanoparticle-modified carbon paste electrode observed in the electrooxidation of different polyphenols. Since the voltammetric response of wine is largely irreversible, another motivation was the possibility of improving the processing of voltammograms to obtain data indicative of wine polyphenols, based on the approach described in the seminal work by Espinoza et al. The modified electrode studied provides an improved and reproducible voltammetric response of gallic acid in wine samples and provides a good basis for further development of an integrated sensor/data system with the possibility of wider application for the quantification of gallic acid as a flavor and visually relevant parameter in winemaking.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

A series of waterborne polyurethane (WBPU)/modified lignin amine (MLA) adhesives was prepared using modified lignin amine (MLA) as a chain extender by a prepolymer mixing process. A successful Mannich reaction was achieved during the synthesis of MLA by reacting lignin with bis(3-aminopropyl)amine. Higher tensile strength, Young’s modulus and thermal stability were recorded for WBPU/MLA adhesives with higher MLA contents. The WBPU/MLA adhesive materials were used to coat PVC substrates. The adhesive strength increased with increasing MLA content. More importantly, the MLA also enhanced the WBPU/MLA coating in terms of adhesive strength at moderately high temperatures as well as under natural weather exposed conditions. The adhesive strength was essentially unaffected with 6.48 mole% MLA in the WBPU/MLA coating after exposure to natural weather conditions for 180 days.

The reproductive health of women is governed by an optimal balance between the host-microbiota interaction. Depletion in the beneficial vaginal microflora caused by depletion of Lactobacillus species and increased proliferation of pathogens results in gynecological infections. Among women of reproductive age, vaginal infections are increasingly prevalent. Attaining therapeutic efficacy using conventional formulations remains a challenge as vaginal fluids quickly remove or dilute the therapeutic formulations. Hydrogels have been widely exploited for targeted delivery of therapeutics directly into the vaginal mucus. With careful choice of polymers (natural, synthetic or semi-synthetic) hydrogels with specific properties such as stimuli-responsiveness, antimicrobial, and muco-adhesiveness can be tailored for higher therapeutic efficacy. In this review, the advnances in hydrogel strategies for the treatment of vaginal infections is presented with emphasis on the types and properties that play a significant role in vaginal drug delivery systems.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

Heavy metal ions (HMIs) have acute toxic effects on the health and are dangerous for human ex-istence and the ecosystem. Therefore, its sensitive and selective detection is of great importance. In recent years various nanocomposite materials have been used by researchers for the detection of HMIs by using various modalities of electrochemical techniques. This review article summarizes the recent advances in developing electrochemical sensors based on numerous nanocomposite mate-rials for detecting heavy metal ions. Nanocomposites materials, such as Metal-Organic Framework (MOF), organic conducting polymers (OCP), carbon nanotubes, graphene/reduced graphene oxide, graphitic carbon nitride, metal oxide, chitosan, mxenes, metal nanoparticle-based nanocomposites, etc. have been explored by various researchers to improve the sensing properties of electrochemical sensors. This review emphasized the synthesis and characterization techniques of nanocomposite materials, modalities for HMI detection by electrochemical technique and the electrochemical sensors. Moreover, this review highlights the development of portable biosensors for detecting HMIs in real-world scenarios, such as environmental monitoring, food safety, and clinical diagnosis. This review also demonstrates the importance of electrochemical sensors-based on nanocomposite ma-terials as a reliable, sensitive, and selective tool for detecting HMIs.

Nanocomposite hydrogels offer remarkable potential for applications in bone tissue engineering. They are synthesized through the chemical or physical crosslinking of polymers and nanomaterials, allowing for the enhancement of their behaviour by modifying the properties and compositions of the nanomaterials involved. However, their mechanical properties require further enhancement to meet the demands of bone tissue engineering. Here, we present an approach to improve the mechanical properties of nanocomposite hydrogels by incorporating polymer grafted silica nanoparticles into a double network inspired hydrogel (gSNP Gels). The gSNP Gels were synthesised via a graft polymerization process using a redox initiator. gSNP Gels were formed by grafting 2-acrylamido-2-methylpropanesulfonic acid (AMPS) as the first network gel followed by a sequential second network acrylamide (AAm) onto amine functionalized silica nanoparticles (ASNPs). We utilized glucose oxidase (GOx), to create an oxygen-free atmosphere during polymerization resulting in higher polymer conversion compared to argon degassing. The gSNP Gels showed excellent compressive strengths of 13.9 ± 5.5 MPa, a strain of 69.6 ± 6.4%, and a water content of 63.4% ± 1.8. The synthesis technique demonstrates a promising approach to enhance the mechanical properties of hydrogels, which can have significant implications for bone tissue engineering and other soft tissue applications.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

This study presents a new bionanocomposite coating on poly(ethylene terephthalate) (PET) made of pullulan and synthetic mica. Mica nanolayers have a very high aspect ratio (α) at levels much greater than that of conventional exfoliated clay layers (e.g., montmorillonite). A very small amount of mica (0.02 wt%, which is ϕ ≈ 0.00008) in pullulan coatings dramatically improved the oxygen barrier performance of the nanocomposite films under dry conditions, whereas this performance was partly lost as the environmental relative humidity (RH) increased. This outcome was explained in terms of the perturbation of the spatial ordering of mica sheets within the main pullulan phase because of RH fluctuations, as confirmed by modelling of the experimental OTR data according to Cussler’s model. The presence of the synthetic nanobuilding block (NBB) led to a decrease in both static and kinetic coefficients of friction compared with neat PET (≈12% and 23%, respectively) and PET coated with unloaded pullulan (≈ 26% reduction in both coefficients). In spite of the presence of the filler, all of the coating formulations did not significantly impair the overall optical properties of the final material, which exhibited haze values below 3% and transmittance above 85%, with the only exception represented by the formulation with the highest loading of mica (1.5 wt%, which is ϕ ≈ 0.01). These findings revealed, for the first time, the potential of the NBB mica to produce nanocomposite coatings in combination with biopolymers for the generation of new functional features, such as transparent high oxygen barrier materials.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.

Because this issue journal is dedicated to Gelatin here we present a few applications of gelatin in the field of optics. It is understood that optics is the science that studies the production, propagation, interaction and detection of light. Regarding the detection there are some materials sensitive to light (photosensitive) that are used like photomultipliers, CCD’s, crystals, two dimension (2D) materials and more. Among the 2D materials the most popular through several centuries has been gelatin based photographic emulsion that records spatial distributions of light. More recently (1970) films made of Gelatin with Dichromate (DCG) and dyes have been used. We describe some characteristics and applications of these two photosensitive materials. Also we describe examples where gelatin is used as Relative Humidity (RH) sensor and in the fabrication of optical elements based on gelatin. This article is intended to researchers outside the optics community.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

In this study, the pristine MgO, MgO/CNT and Ni-MgO/CNT nanocomposites were processed by the impregnation and chemical vapour deposition methods and analyzed for hydrogen evolution (HER) via electrochemical water splitting process. Furthermore, effect of nickel on the deposited carbon was systematically elaborated in this study. The highly conductive carbon nanotubes (CNTs) deposited on the metal surface of the Ni-MgO nanocomposite heterostructure provides the robust stability and superior electrocatalytic activity. The optimized Ni-MgO/CNT nanocomposite exhibited hierarchical helical-shaped carbon nanotubes adorned on the surface of the Ni-MgO flakes, forming a hybrid metal-carbon network structure. The HER catalytic reaction was carried out in 1M alkaline KOH electrolyte, and the optimized Ni-MgO/CNT nanocomposite achieves the low 117 mV overpotential value (ɳ) at the 10 mA cm-2 and needs low 116 mV/dec Tafel value denoted Volmer-Heyrovsky pathway. Also, high electrochemical active surface area (ECSA) value of Ni-MgO/CNT nanocomposite acquires 515 cm2, which is favorable for the generation of abundant electro-active species and the prepared electrocatalyst durability was also performed by chronoamperometry test for prolonged duration of 20 h at 10 mA cm-2 and exhibits the good stability with 72% retention. Hence, obtained results demonstrated that the optimized Ni-MgO/CNT nanocomposite is highly active and cost-effective electrocatalyst towards hydrogen energy production.

Polyvinyl Alcohol (PVA)/ Graphene Quantum Dots (GQDs) polymer nanocomposite films have been prepared, and the relationship between their structural, thermal and nanoscale morphologi-cal properties, and their photoluminescent response, has been investigated. Although according to X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FT-IR) and Differential Thermal Analysis (DTA) the incorporation of GQDs does not significantly affect the percentage crystallinity of the PVA matrix, for a range of added GQD concentrations, Atomic Force Micros-copy (AFM) showed the formation of islands with apparent crystalline morphology on the surface of the PVA/GQD films, with GQD presumably acting as a nucleating agent for island growth. The incorporation of GQD also led to the formation of characteristic surface pores with increased stiffness and frictional contrast, according to Ultrasonic Force Microscopy (UFM) and Frictional Force Microscopy (FFM) data. The photoluminescence (PL) spectra of the films were found to de-pend both on the amount of GQD incorporated and on the film morphology. For GQD loads > 1,2wt%, a GQD-related band was observed at ~ 1650 cm-1 in FT-IR, along with an increase in the PL band at lower energy. For a load of ~2wt% GQD, the surface morphology was characterized by extended cluster aggregates with lower stiffness and friction than the surrounding matrix, and the PL signal decreased.

A nonlinear MEMS multimass sensor is investigated. The MEMS design consists of an array of nonlinear microcantilevers clamped to a shuttle mass which, in turn, is attached to a linear spring and a dashpot. The microcantilevers are made of a polymeric hosting matrix reinforced by aligned carbon nanotubes (CNT) with different CNT volume fractions in each cantilever so as to suitably tune the frequency bandwidth of the device. The advantages of a single input-single output (SISO) system are here exploited for the design, actuation and detection principles as in previous literature.

Green electrospun materials are gaining popularity in the quest for a more sustainable environment for human life. Bee pollen (BP) is a valuable apitherapeutic product, which has many beneficial properties such as antioxidant properties and antibacterial activity. Alginate is a natural and low-cost polymer. Both natural materials show good compatibility with human tissues for biomedical applications and have no toxic effect on the environment. In this study, the production of bee pollen loaded sodium alginate (SA) and polyvinyl alcohol (PVA) nanofibrous mat was fabricated by electrospinning technique. The green electrospun composite mats were characterized by scanning electronic microscopy (SEM), Fourier transforms infrared spectroscopy (FTIR), and differential scanning calorimeter (DSC). According to the findings of the study, the toxin-free electrospinning method is suitable for producing green composite material. Because of the useful properties of the bee pollen and the favorable biocompatibility of the alginate fibers, the bee pollen-loaded SA/PVA electrospun mats have the potential for use in a variety of biomedical applications.

In this research, first a binary nanocomposite of magnetic recyclable photocatalyst Fe₃O₄/TiO₂, was synthesized by sol gel technique. Then, in order to enhance the photocatalytic activity of the synthesized nanocomposite, it was deposited by silver nanoparticles for using in degradation of organic pollutants 2, 4-dichlorophenol (2, 4-DCP) under visible light. A range of analytical techniques including XRD, FESEM/EDX, DRS, VSM and N₂ physisorption were employed to reveal the crystal structure, morphology and property of the nanocomposites. We obtained 32% and 55% degradation of 2, 4-DCP under visible light after 180 min irradiation in the presence of Fe₃O₄/TiO₂ and Fe₃O₄/TiO₂/Ag respectively. Thus, the excellent visible light photocatalytic activity of Fe₃O₄/TiO₂/Ag sample can be attributed to the surface plasmon resonance effect of Ag nanoparticles deposited on Fe₃O₄/TiO₂ nanocomposite.

The need to develop novel lightweight materials and their manufacturing processes is sets out to meet the new aerospace, automotive and construction requirements. Within this context, this research work is proposed to develop a novel thermoplastic composite material with high mechanical properties. These composites will be based on thermoplastic matrixes made from polyamide and 35% short glass fiber filled-polyamide reinforced with different types of fabrics. As reinforcement, glass fiber fabrics will be used as the base. They will be treated with different processes, both chemical and physical, to promote adherence to the matrix. Textile overmoulding technology was selected for manufacturing these composites. This technology was primarily developed to manufacture aesthetic lined components and has achieved a great implantation. Once these new composites are manufactured, they will be submitted to different tests to evaluate their behavior regarding adhesion, impact strength and stiffness. It is expected an improvement on stiffness and impact absorption.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

.Maize cultivation in Thailand faces challenges owing to climate change and soil organic carbon (SOC) loss. This highlights the importance of comparing maize soil with paddy soil in terms of the role of dissolved organic carbon (DOC) and nutrient availability, as they influence SOC content. Soil samples from Chiang Mai province, primarily Fluvisol, were collected for the cultivation of paddy rice and maize, analysed for carbon fractions and chemical properties, and categorised into layers. Comparative analysis revealed that maize soils had lower levels of labile carbon components and organic carbon than paddy soils (P

It is often difficult to extract data on material and energy wates and related costs in the value chain of conventional production units. Many organizations are not fully aware of the actual cost of material and energy waste. For this purpose, advanced costing methods should be used. This study uses material and energy flow cost accounting to determine material costs, losses, and waste management. The case study of this research is the construction of turbine blades in Iran Power Plant Company. In this study, using the extracted data, the construction costs of turbine blades have been studied. The conventional method of making a turbine blade is the machining method, which we will see has a huge amount of wastes of materials and energy. By studying different methods, we will find that there is an alternative method called forging, which reduces losses and costs. Finally, the costs of the two methods are compared. Engineering economics techniques have also been used to compare two methods on a long-term planning horizon.