The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

Pea shoots is a popular vegetable in certain regions of the world due to their unique taste and abundance of health-promoting phytochemicals. The perishable nature and susceptibility of root rot of pea shoots necessitate a new soilless production system located close to the market. This study compared the growth of pea shoots using various cultivation methods in LED plant factory. The results showed that early topping (4 days after transplanting, ET) promoted early harvest compared to later topping (20 days after transplanting, LT) and increased the number of harvested shoots by extending the harvest time to 2.8 times, ultimately resulting in a substantial yield improvement. Moreover, the yield of ET with lower planting density (72 plants m-2, ET-LD) was 8.7% higher than ET with higher planting density (126 plants m-2, ET-HD). Particularly, the average fresh weight of individual pea shoots under ET-LD exceeded that of ET-HD by 48.9%. It is advisable to consider adopting ET-LD for the cultivation of pea shoots in LED plant factory. Based on ET-LD, the yield, nutritional quality, and light use efficiency of pea shoots were further explored at different stages under three levels of light intensity (50, 100, 150 μmol m-2 s-1). Contrasted against the light intensity of 50 μmol m-2 s-1, the average fresh weight per pea shoots, number of harvested, and total fresh yield under light intensity of 150 μmol m-2 s-1 treatment increased by 60.2%, 62.8%, and 165.1%, respectively. Meanwhile, the fresh weight per pea shoots, photosynthetic capacity, soluble sugar and vitamin C levels in leaves, as well as light use efficiency and photon yield, initially increased and then decreased with the extension of the planting period. Among these, soluble sugar, LUE, and PY started to decrease after reaching the maximum value at 60-70 days after transplanting. In conclusion, light intensity of 150 μmol m-2 s-1 with a photoperiod of 16 h d-1 using LEDs, combined with early topping within a planting period of 60-70 days, proves to be suitable for the hydroponic production of pea shoots in LED plant factory.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

This study provides a comprehensive analysis of the conformational dynamics of pseudo-endocannabinoid receptors (p-CBRs) CB₁ and CB₂ in response to ligand binding. The ligands studied include N-arachidonoyl dopamine (NADA), Cannabidiol (CBD), known agonists (FUB-MDMB and E3R), and inverse agonists (Taranabant and AM630). Using homology models based on crystal structures (PDB ID: 5U09 for CB₁ and 5ZTY for CB₂), molecular docking, and molecular dynamics (MD) simulations, the research validates the structural integrity and dynamic behaviours of these pseudo-receptors. Induced-fit docking revealed NADA as having the highest binding affinity for both receptors, with docking scores of −13.92 kcal/mol for CB₁ and −13.32 kcal/mol for CB₂, facilitated by key hydrogen bond interactions. MD simulations over 250 ns at ~298 K showed successful equilibration, indicating the most stable interaction for NADA, thereby further validating the models. CB₁ and CB₂ exhibited distinct conformational responses to ligands, with Cα RMSD and Cα RMSF analyses suggesting a more rigid binding pocket for CB₁ and a flexible binding pocket for CB₂. These findings highlight the significance of receptor behaviour and dynamics in the development of cannabinoid-based therapeutics, supporting the potential of CBD and NADA as modulators for CB₁ and CB₂, respectively.

Faraday's Law of induction is often stated as "a change in magnetic flux causes an EMF"; or, more cautiously, "a change in magnetic flux is associated with an EMF"; It is as well that the more cautious form exists, because the first "causes" form can be shown to be incompatible with the usual expression for EMF. This is not, however, to deny the causality as reasonably inferred from experimental observation ­ it is the equation for Faraday's Law of induction which does not represent the claimed cause-and-effect relationship. Here we investigate a selection of different approaches, trying to see how an explicitly causal mathematical equation, which attempts to encapsulate the "a change in magnetic flux causes ..." idea, might arise.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

Chemical plants are characterized by the management and operation of various hazardous materials; thus, accident risk is inherently high. Nevertheless, the incidence of chemical accidents in Korea has effectively stabilized, with no marked increase attributable to the implementation of systematic safety management procedures based on process safety management system principles. In June 2023, the Ministry of Employment and Labor in Korea unveiled the Serious Injury and Fatality (SIF) report, meticulously cataloging 4,432 instances of grave accidents spanning six years (2016–2021). The compilation comprises 1,834 and 2,574 cases within the manufacturing and affiliated sectors and the construction sector, respectively. This study provides an overview of each accident, and elucidates the causes, and recommends preventative strategies. The objective was to galvanize companies across various industrial landscapes and fortify their intrinsic safety management protocols by using accident data delineated per sector. Sixteen specific accident cases from the SIF report, all of which occurred in facilities regulated by process safety management (PSM), were investigated. Technical analysis was conducted, focusing on explosion accidents within the organic catalyst packaging process, notable for their unique patterns of occurrence. This analysis extended to an examination of the reproducibility of such accidents. Employing two system analysis methodologies, system theoretic accident model and process and barrier-based systemic cause analysis technique, this study provides insights into the causative factors of the accidents and formulates comprehensive strategies for the prevention of future accidents. The findings will contribute significantly to reducing the risk of accidents within the catalyst packaging domain and assist in the development of robust recurrence prevention measures.

“A Picture is worth a thousand words”. Given an image, humans are able to deduce various cause-and-effect captions of past, current, and future events beyond the image. The task of visual commonsense generation aims at generating three cause-and-effect captions (1) what needed to happen before, (2) what is the current intent, and (3) what will happen after for a given image. However, such a task is challenging for machines owing to two limitations: existing approaches (1) directly utilize conventional vision-language transformers to learn relationships between input modalities, and (2) ignore relations among target cause-and-effect captions but consider each caption independently. We propose Cause-and-Effect BART (CE-BART) which is based on (1) Structured Graph Reasoner that captures intra- and inter-modality relationships among visual and textual representations, and (2) Cause-and-Effect Generator that generates cause-and-effect captions by considering the causal relations among inferences. We demonstrate the validity of CE-BART on VisualCOMET and AVSD benchmarks. CE-BART achieves SOTA performances on both benchmarks, while extensive ablation study and qualitative analysis demonstrate the performance gain and improved interpretability.

Out-of-hospital cardiac arrest (OHCA) represents a significant global public health burden, characterized by low survival and few established diagnostic tools to guide intervention. OHCA presents with a wide variety of etiologies in a heterogeneous population, posing a clinical challenge to care teams. In this review, we describe evolving research focused on diagnostic approaches to OHCA following resuscitation, including electrocardiography, coronary angiography, computed tomography, ultrasonography, and serologic biomarker assessment. These diagnostic tools have been employed in post-resuscitative efforts for diagnosing ischemic and non-ischemic cardiac, respiratory, neurologic, vascular, traumatic, and metabolic causes of arrest.

Background: Both hypertension and carotid atherosclerosis are independent risk factors for cardiovascular disease. Understanding their combined impact could enhance risk assessment and management strategies. Hypothesis: We hypothesized that the synergistic effects of hypertension and carotid plaques would increase the risk of both cardiovascular events and all-cause mortality. Methods: A follow-up study was conducted at the Preventive Cardiology department of Vilnius University Hospital Santaros klinikos between 2012 and 2021. The study recruited participants aged 40-60 who did not have overt CVD and were part of the Lithuanian High Cardiovascular Risk primary preventive program. The study collected demographic and clinical data, including an ultrasound assessment of carotid plaque. The participants were monitored for 4-10 years for CVD events and all-cause mortality. Results: Among 6,138 participants, 954 (16%) experienced cardiovascular disease (CVD) events. The presence of carotid plaque on both sides was significantly associated with CVD events, myocardial infarction, and all-cause mortality. However, the combination of hypertension and carotid plaque did not significantly increase the risk for CVD events, stroke, or all-cause mortality. Conclusion: The combination of hypertension and carotid plaque did not significantly increase the risk of CVD events or all-cause mortality. CV events depend on the spread of the atherosclerosis process in the carotid vessels.

: Schizophrenia and schizoaffective disorder are generally treated with second-generation antipsychotic drugs. These drugs are mostly D2 and 5-HT2A antagonists. They improve positive schizophrenia symptoms sufficiently well; however, they ameliorate negative schizophrenia symptoms and cognitive functions to a small extent. We review novel antipsychotic drugs exerting a partial agonism at dopaminergic and serotonergic receptors such as cariprazine, brexipiprazole and lumateperone. Besides, the mechanisms of actions of non-anti-dopaminergic antipsychotic drugs are pointed out. Updated neural networks are used to explain the mechanism of action of M4 and M1 receptor agonists, for example xanomeline combined with trospium or emraclidine, and trace-amine-associated receptor 1 agonists (TAAR1), for example ulataront. Phase 3 clinical trials of new third generation antipsychotic drugs are presented. Novel antipsychotic drugs with a partial agonism at D2 and D3 receptors improve positive and negative schizophrenia symptoms as well as cognitive symptoms better than second generation antipsychotic drugs. Besides, they are well tolerated. M4 and M1 receptor agonists, i.e. xanomeline combined with trospium or emraclidine, and TAAR1 agonists, i.e. ulataront, have promising results in clinical trials; they well improve negative schizophrenia symptoms and cognitive functions. Phase 3 clinical trials offer promising results for anti-dopaminergic and non-anti-dopaminergic novel antipsychotic drugs. These new non-anti-dopaminergic antipsychotic drugs better emend negative schizophrenia symptoms, and they better improve cognitive functions than second-generation antipsychotic drugs. Promising new antipsychotic drugs are cariprazine, brexipiprazole, lumateperone, ulataront, and xanomeline combined with trospium. Although phase 3 clinical studies are not yet completed, they showed a therapeutic effect superior to those achieved by second-generation antipsychotic drugs. They are tolerated very well, and they better treat negative schizophrenia symptoms and improve cognitive functions.

This study examines the effects of working capital management strategies on firm’s financial performance of Indian cement companies using 11-year (2010-2020) financial data of 31 companies listed in Bombay Stock Exchange. It is intended to find out whether the strategies made by finance managers with respect to the components of working capital such as average receivable period, inventory conversion period, average payment period and cash conversion cycle, etc. affects the firm’s performances individually and in total. The results of Pearson’s correlation coefficient and random effect regression model shows that there exists a negative relationship between financial performance measured in terms of return on assets (ROA) and inventory turnover period (ITP) as well as accounts payable period (APP), whereas firm’s performance is not significantly affected by accounts receivable period (ARP) and cash conversion cycle (CCC). Similarly, it has been observed that the liquidity measures such as current ratio (CR) and quick ratio (QR) have a significant positive association with ROA. Moreover, the size of the firms and leverage are inversely related to ROA but the age of the firms is not significantly affecting their financial performances. Hence, it can be concluded that how an organisation designs its working capital strategy do have an impact on its performances.

The material properties and structural characteristics of ballistic composites are crucial to their ballistic performance. Investigation for the influence of the material and structural parameters of UHMWPE body armor on anti-fragmentation penetration performance has been made by numerical simulation in this paper, with a numerical modeling simulating the penetration of a 1.1 g FSP into the target plate of UHMWPE body armor, by which the simulation results demonstrate that the failure process of the body armor target plate primarily involves shear damage, interlayer delamination, and tensile damage. Furthermore, the study evaluates the effects of elastic modulus, tensile strength, shear strength, number of layers, and interlayer strength on the ballistic limit velocity of UHMWPE body armor. The findings reveal that the ballistic limit velocity is most sensitive to changes in shear strength, with variation rates ranging from -18.02% to 10.81%, showing an approximate positive correlation, while the elastic modulus has the smallest impact on ballistic limit velocity, with variation rates ranging from -1.8% to 3.6%. Additionally, appropriate interlayer strength can improve the ballistic limit velocity of the body armor to a certain extent. This study provides theoretical methods and recommendations for optimizing anti-penetration performance of UHMWPE body armor.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

Cytomegalovirus infection contributes to 10-30% congenital hearing loss in children. Vertebrate peripheral auditory organs include the outer, middle and inner ear. Their development is regulated by multiple signaling pathways. However, most ear diseases due to viral infections are due to congenital infections and reactivation, and affect healthy adults to a lesser extent. This may be due to the fact that viral infections affect signaling pathways that are important for the development of peripheral hearing organs. Therefore, an in-depth understanding of the relationship between viral infections and the signaling pathways involved in the development of peripheral hearing organs is important for the prevention and treatment of ear diseases. In this review, we summaries the effects of viruses on signaling pathways and signaling molecules in development of peripheral auditory organ, with a focus on Human cytomegalovirus as an example.

In order to solve the problem of structure damage location and degree identification, the weighted mean of vectors algorithm (INFO), a high-performance optimization one, was first introduced to identify structure damage. The genetic algorithm (GA) are improved to obtain a refined genetic algorithm (RGA). An objective function is constructed by combining the dynamic response transfer-ratio without modal analysis. INFO and RGA algorithms are used to optimize the objective function for damage identification. Though simulations, the INFO, RGA, GA algorithms were used to identify the damage on a simply supported beam and cantilevered plate with different levels of noise and different frequency spacing of pickup points. The simulations verify the effectiveness of the three damage identification methods, and the INFO algorithm has the highest damage identification accuracy, the RGA is second and the GA is the worst.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

In this work, we introduce the first pipeline that combines a refraction-aware Structure-from-Motion (SfM) method with a deep learning model specifically designed for airborne bathymetry. We accurately estimate the 3D positions of the submerged points by integrating refraction geometry within the SfM optimization problem. This way, no refraction correction as post-processing is required. Experiments with simulated data that approach the real-world capturing conditions demonstrate that SfM with refraction correction is extremely accurate, with submillimeter errors. We integrate our refraction-aware SfM within a deep learning framework that also takes into account radiometrical information, developing a combined spectral and geometry-based approach, with further improvements on accuracy and robustness to different seafloor types, both textured and textureless. We conducted experiments with real-world data at 2 locations in the southern Mediterranean Sea, with varying seafloor types which demonstrate the benefits of refraction correction for the deep learning framework. We open-source our refraction-aware SfM, providing researchers in airborne bathymetry with a practical tool to apply SfM in shallow water areas.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

In the vaginal ecosystem there is a symbiotic relationship between the microbiota and the host, particularly Candida spp., which are considered commensals of the vaginal mucosa. During pregnancy there is an increase in hormonal secretion that alters the vaginal microbiota and favors the development of Candida infection. Several studies have shown the increased prevalence of Candida during pregnancy, as well as its association with perinatal complications and current clinical practice guidelines recommend fluconazole as the treatment of choice during pregnancy in case of infection by Candida albicans and non-albicans Candida. However, in the Mexican population, this association has not been studied. So in this study, an intentional search for colonization by Candida spp. in pregnant women who attended the obstetric triage of the Hospital Regional de Alta Especialidad de Ixtapaluca during the period from May to October 2019, and they were followed up until the end of the pregnancy. Data on age, number of pregnancies, gestational age, body mass index, and perinatal outcomes were analyzed. Of 83 patients included in the study, yeasts corre-sponding to C. albicans (12) and C. glabrata (4) were isolated in 16. In the group of patients with Candida, the maternal age range was from 15 to 36 years old, of which 7 were adolescents and 2 with advanced maternal age, with an average of 2 gestations, the range of body mass index was from 19.3 to 42.4, of which 4 were overweight and 7 obese. Perinatal complications were observed in three patients, one presented chorioamnionitis and in two the neonates were small for gestational age. No association was found between colonization by Candida spp. and the number of preg-nancies, gestational age, body mass index or perinatal results. However, it was found that age (adolescence) may be a risk factor for the development of vulvovaginitis during pregnancy.

The effective macroscopic model describing interactions of a viscous compressible heat-conducting fluid and a two-level fine bristly thermoelastic structure is derived from microstructure by means of the Allaire–Briane multi-scale convergence method. This new model naturally generalizes the isothermal formulation earlier constructed by the authors in 2020, see in Siberian Electronic Mathematical Reports, vol. 17 (https://doi.org/10.33048/semi.2020.17.100). In applications, the established model can be used, for example, in description, with account of heat transfer phenomemon, of airflow near surface of plant’s leaf, in simulation of epithelium surfaces of blood vessels, and in design of biotechnological devices operating in liquids.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

As recently as 2002 programmed aging in mammals was widely thought to be theoretically impossible based on generally accepted concepts regarding the evolution process. However, as described in this article, genetics discoveries, results of selective breeding, and other direct evidence strongly support the idea that aging creates an evolutionary advantage and that therefore complex biological mechanisms evolved that control mammal aging. Like similar life-cycle programs that control reproduction, growth, and menopause the aging program can adjust the aging trait during an individual’s life to compensate for temporary or local changes in external conditions that alter the optimum lifespan for a particular species population. In addition, genetics discoveries strongly support the evolvability concept to the effect that sexually reproducing species can evolve design features that increase their ability to evolve, and that aging is one such feature.

The advent of modern satellite technology has transformed observational astronomy and astrophysics, offering unprecedented insights into the large-scale behavior of gravitation and challenging established cosmological models. This technological progress has reinvigorated the study of relativistic cosmology, leading to a critical reassessment of foundational assumptions, particularly the cosmological principle, which posits that the universe is homogeneous and isotropic on large scales. While this principle underpins the Standard Cosmological Model and the Friedmann-Lemaitre-Robertson-Walker metric, emerging data has increasingly been challenging its validity. Central to this investigation are the redshift-distance and light intensity-distance relations, essential for testing cosmological models. The integration of both parametric and nonparametric redshift models provides a more comprehensive analysis, addressing discrepancies in our understanding of the universe's structure and evolution. However, unresolved mysteries, particularly concerning dark matter and dark energy, complicate these models. This research critically examines the cosmological principle using the latest observational data and scrutinizes the Friedmann model's assumptions. The study shows that galaxy formation was most rapid in the early universe, especially within the redshift range of , with notable peaks around at and These two characteristic redshift values, predicted by our standard Friedmann redshift model used in this work, are confirmed by the observational data utilized in this research. The research also highlights that dark matter plays a significantly more critical role than dark energy in the process of galaxy formation. While dark energy primarily affects the large-scale expansion of the universe, dark matter seems to go beyond the domination of local galaxy formation and evolution of cosmic structures. These findings underscore the limitations of current models and contribute to the ongoing refinement of cosmological theories, offering a clearer understanding of the universe’s evolution.

A review is given of the experimental values of the magnetic hyperfine structure and the Bohr-Weisskopf effect in muonic atoms. The need for more measurements and systematic calculations is discussed in the light of distinguishing between different models of the Bohr-Weisskopf effect in nuclei.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Currently, the use of recycled waste plastic in road construction is not just considered ecofriendly but also considered advantageous for improving road performance over time. This research explores using recycled plastic bags, made of low-density polyethylene (LDPE), in asphalt mixtures to improve road performance and manage waste. The study aims to assess the effects of incorporating different amounts of shredded waste plastic into asphalt mixes and determine the optimal percentage. The aggregate used was obtained from Sargodha quarry Pakistan and asphalt used was 60/70 grade obtained from national refinery limited Pakistan. Using the Marshall mix design, the optimum bitumen content (OBC) was found to be 4.5% of the asphalt mix weight. Thirty samples were tested with waste plastic proportions of 6%, 8%, 10%, 12%, and 14% of OBC weight, along with a standard mix. Tests on stability, bulk density, flow, and air voids showed that a 10% plastic content significantly enhances asphalt performance, increasing stability by around 25%. The study recommends using 10% plastic by OBC weight in asphalt mixes for better performance and suggests further research on optimal incorporation techniques of waste materials in asphalt mixtures.

Floral nectar is a key reward in Leguminosae despite the exceptional diversity of flowers in this family. The paper aims to summarize the available data on structure, ontogeny, regulation, and possible evolution of the leguminous floral nectaries. To date, detailed characterization of ultrastructure and mode of secretion is available only for a few representative of the family whereas the majority remains understudied from this perspective. In most cases, regardless of flower symmetry, nectaries are localized between stamens and a carpel. The nectar is usually exuded from modified stomata although the exact mode of secretion by specialized parenchyma may differ between taxa. The leguminous floral nectaries often have certain features of monosymmetry with preferentially abaxial development. Nectaries were independently lost in several lineages, and equally recurrent is the emergence of substitutive, i.e. evolutionary innovative, nectar-producing structures. Floral nectaries possess a certain degree of evolutionary inertia, i.e. they remain stable even in lineages in which flower morphology underwent significant changes compared with an ancestral plan, such as shifts in merism, symmetry, organ number and alike. Due to their evolutionary stability, floral nectaries are rarely used in taxonomy of Leguminosae.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

To clarify effects of weathered coal humic acid on water-stable aggregates and pore characteristics of reclaimed cambisol, this research analyzed the evolution characteristics of soil aggregates and pores. Effects of different humic acid dosages (0, 1%, 3%, and 5% by weight) and application period (1 year, 2 years, and 3 years) on soil aggregates and organic carbon components in soil water-stable aggregates were investigated. The results showed that water-stable macroaggregates (>0.25 mm) had the highest content in the first year; but in the third year, water-stable microaggregates (0.053–0.25 mm) had the highest content, and silt and clay (<0.053 mm) were at a maximum. In the third year of 5% treatment, mean weight and geometric mean diameters were the largest, soil structure was the most stable, and TOC and water-stable microaggregates (0.053–0.25 mm) in soil had the highest proportions. For 5% treatment, the majority of irregular pores were independent in the first year, and number of pores decreased in the second year, but average pore volume increased, forming robust connected pores. In the third year, the number of elongated and irregular pores increased. In the third year of 5% treatment, most pores were irregular and of size >100 μm, and soil structure was the most stable.

Flexible wearable pressure sensors offer numerous benefits, including superior sensing capabilities, a lightweight and compact design, and exceptional conformal properties, making them highly sought after in various applications including medical monitoring, human-computer interaction, and electronic skin. Because of their excellent characteristics, such as simple fabrication, low power consumption, and short response time, capacitive pressure sensors have received widespread attention. As a flexible polymer material, polydimethylsiloxane (PDMS) is widely used in the preparation of dielectric layers for capacitive pressure sensors. The Young's modulus of the flexible polymer can be effectively decreased through the synergistic application of sacrificial template and laser ablation techniques, thereby improving the functionality of capacitive pressure sensors. In this study, a novel sensor was developed through a series of processes including sacrificial template method using NaCl microparticles, CO₂ laser ablation, and sandwiching a porous PDMS dielectric layer between two flexible electrodes to create a capacitive pressure sensor. The sensor demonstrates a sensitivity of 0.694 kPa-1 within the pressure range of 0-1 kPa, and can effectively detect pressures ranging from 3 Pa to 200 kPa. The sensor demonstrates stability for up to 500 cycles, with a rapid response time of 96ms and a recovery time of 118ms, coupled with a low hysteresis of 6.8%. Furthermore, our testing indicates that the sensor possesses limitless potential for use in detecting human physiological activities and signaling emergencies.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

The atomic structures of Zn and Na borophosphate glasses were studied by X-ray and neutron diffraction. Peaks assigned to the B−O, P−O, and O−O distances confirm that only BO4 units co-exist with the PO4 tetrahedra. The Zn−O and Na−O coordination numbers are found to be a little larger than four. The narrowest peaks of the Zn−O first-neighbor distances exist for the glasses along a line connecting the Zn(PO3)2 and BPO4 compositions (50 mol% P2O5) which is explained by networks of ZnO4, BO4, and PO4 tetrahedra with twofold coordinated oxygens. Calculated amounts of the available oxygen support this interpretation. Broadened peaks occur for glasses with lower P2O5 contents, consistent with the presence of threefold coordinated oxygens. The two distinct P−O peak components of the Zn and Na borophosphate glasses differ in their relative abundances which is interpreted by Na+ cations that coordinate oxygens in some P−O−B bridges, something not seen for the Zn2+ ions.

This study used Dutch potatoes at the end of dormancy as the material to explore the impact of menthol (0.2 and 0.5 g/kg based on potato mass) treatment on sprouting inhibition and potato quality. The findings revealed that a menthol concentration of 0.5 g/kg effectively inhibited potato tuber sprouting and significantly reduced glucoside alkaloids production. After a storage period of 15 days, the sprouting percentage and glucoside alkaloids content of potatoes treated with 0.5 g/kg menthol were observed to be significantly lower at 4.17% and 68.63 mg/kg, respectively, compared to the control group which exhibited values of 100% and 282.01 mg/kg, respectively (P < 0.05). Throughout the storage period, 0.5 g/kg of menthol promoted respiration, reduced malondialdehyde production in potatoes, inhibited polyphenol oxidase activity, and slowed down tissue browning. Additionally, it mitigated the decline in starch and soluble protein content, inhibiting the accumulation of reducing sugars.

Causal relationships lie at the very core of our scientific description of biophysical phenomena. Nevertheless, observable facts such as chaotic dynamics, symmetry breaks, long-range collisionless neural interactions, zero-value energy singularities, particle/wave duality, ecological approaches to visual perception elude cause effect inductive explanations. We illustrate how simple topological claims, seemingly useless and far away from scientific inquiry (e.g., “given at least some wind on Earth, there must at all times be a cyclone or anticyclone somewhere”; “if one stirs to dissolve a lump of sugar in a cup of coffee, it appears there is always a point without motion”; “at any moment, there is always a pair of antipodal points on the Earth’s surface with equal temperatures and barometric pressures”) describe a real world, made of projections and mappings unsupplied with causality. Unavoidable, necessary, passive, spontaneous changes in systems’ shapes, dimensions and symmetries incarnate biophysical quantifiable counterparts of abstract mathematical concepts. Real features arising from topological mechanisms do not require causal powers to be produced, because are independent of exerted physical forces, energetic fields’ actions and thermodynamic constraints. Providing examples that shed novel interpretative light on phenomena such as double slit experiments, cellular mechanisms and brain function, we conclude as follows: countless scientific matters can be accessed through methodological weapons which not just break causality, replace temporal correlations and probabilistic a priori knowledge of previous cases, but also permit augments in available information devoid of entropy increases and energy losses.

The Regulation (EU) 2016/429 establishes new extensive guidelines for managing transmissible animal diseases, including zoonoses. The Commission Implementing Regulation 2018/1882 classifies diseases into five categories based on their prevalence and the required response, ranging from eradication to surveillance. Key aspects of the regulations concern emphasis on animal traceability, biosecurity, wildlife pathogen control, sustainable farming, and the reduction of the impact of diseases on both public and animal health, as well as on the environment. These align with the European Green Deal, the Farm to Fork Strategy and the One Health approach. In Italian inland areas—similarly to other European regions that are fragile, remote from major service centers, and often neglected—agropastoral and agri-food activities are beneficial for tourism, commercialization of typical foods, and recreational activities. In these areas including the Molise Region, the activation of optional programmes within the framework of the aforementioned regulations could help control infectious animal diseases that are not subject to mandatory eradication but cause income loss and trade restrictions, such as infectious bovine rhinotracheitis and paratuberculosis, a suspected zoonosis potentially linked to Crohn's disease in humans. These programmes could boost the economic income of local extensive breeding, counteract depopulation, and protect human health and the environment.

Introduction: Lipoyl transferase 2 is involved in biosynthesis of the lipoate. Lipoate is the cofactor for the glycine cleavage system and four dehydrogenase enzymes. Biallelic variants in LIPT2 causing severe neonatal encephalopathy was first described in 2017. Methods: Clinical data was collected by retrospective chart review after obtaining consent from parents. The pathogenicity of these variants was further delineated using a yeast model. The YEp352-LIPT2 plasmid was used as a template to generate the two patient variants using QuickChange Lightning Site-Directed Mutagenesis Kit. Results: Patient was a 15-month-old female who presented at 1 month with dystonia, developmental delay and feeding difficulties. MR Brain showed cortical malformations including colpocephaly, polymicrogyria and heterotopia. Patient had elevations in lactate (6.1 mmol/L) and glycine. Exome sequencing showed 2 variants of uncertain significance in trans in the LIPT2 gene: c.346 G>T and c.418C>T. Patient was started on lipoic acid, thiamine and COQ10. Yeast complementation experiments indicate that both patient mutation variants result in diminished function versions of the LIPT2 protein. Conclusion: We report the fourth case of LIPT2-related disorder. Proband shared significant overlap with previous patients, however had a distinct movement disorder and brain malformations which have not been previously described. Unlike most neurometabolic disorders where dystonia develops later after metabolic stroke in basal ganglia, LIPT2- related disorder seems unique due to early onset of dystonia due to energy deficit in the developing brain. Lipoic acid supplementation has not led to significant clinical improvement. Analyses in yeast indicate that novel variants are deleterious but have retained some functionality.

Continuous-flow microwave heating stands out for its ability to rapidly and uniformly heat substances, making it widely applicable in chemical production. However, in practical applications, the permittivity of the heated liquid changes dramatically as the reaction progresses, affecting the efficiency and uniformity of continuous-flow heating. Herein, this work presents a novel microwave heating device based on coaxial structure for high-performance heating. Our approach commenced with the development of a multi-physical field model, incorporating a spiral polytetrafluoroethylene (PTFE) as a water channel and the coaxial waveguide as a container was established. The analysis shows that the uniform distribution of the sectional electric field of electromagnetic waves in the TEM mode within the coaxial structure can enhance heating uniformity. Then, a continuous-flow microwave heating system for different liquid loads was established, and experimental measurements were conducted. The heating efficiency for all loads exceeded 90%, which basely matched the simulation results, validating the accuracy of the model. Finally, the heating efficiency and uniformity under different permittivity loads were analyzed, as well as the impact of channel radius on heating efficiency. The device demonstrated high heating efficiency and stable heating uniformity across different loads. This continuous-flow microwave device is suitable for chemical research and production, contributing to the promotion of microwave energy applications in the chemical industry.

The dielectric constant (ε) reflects the ability of a material to align and orient electrical dipoles within its structure in response to an externally applied electric field; the greater the polarizability of molecules, the greater the value of dielectric constant. In this study a data set of 86 polymers was investigated to develop a structure-property quantitative relations (QSPR) model to predict the dielectric constant in polymers. An initial set of 1273 descriptors was used to select a best set of descriptors and to construct two machine learning models with Gradient Boosting Regressor (GB_A and GB_B). The best performing model (GB_A) with 8 descriptors, exhibited a performance of (R2train) = 0.938 and (R2test) = 0.802. The models were internally validated by 5 folds cross-validation, demonstrating robustness. Additionally, using the Accumulative Local Effect (ALE) technique, we analyzed the relationship between the 8 descriptors involved and the impact of these descriptors to dielectric constant of polymers.

Idiopathic acute pancreatitis (IAP) presents a diagnostic challenge and refers to cases where the cause of acute pancreatitis remains uncertain despite a comprehensive diagnostic evalua-tion. Endoscopic ultrasound (EUS) has emerged as a valuable tool in the diagnostic workup of IAP. This review explores the pivotal role of EUS in detecting the actual cause of IAP, as-sessing its accuracy, timing, safety, and future technological improvement. Following PRISMA guidelines, 60 pertinent studies were selected and analysed. EUS emerges as a cru-cial diagnostic tool, particularly when conventional imaging fails. It can offer intricate visu-alization of the pancreas, biliary system, and adjacent structures. High accuracy of EUS is evident in detecting the actual causes of IAP such as microlithiasis, small bile duct stones, pancreas divisum, and small pancreatic tumors. Optimal timing for EUS is post-resolution of the acute phase of the disease. EUS, when conducted by experienced endoscopists, it boasts minimal safety concerns, and is crucial to prevent complications. EUS-guided interventions, including fine-needle aspiration, collection drainage, and biopsies, aid in cytological analy-sis. With high diagnostic accuracy, safety, and therapeutic potential, EUS is able to improve patient outcomes when managing IAP. Further refinement of EUS techniques and cost-effectiveness assessment of EUS-guided approaches need to be explored in multicenter prospective studies. This review underscores EUS as a transformative tool in unraveling IAP's enigma and advancing diagnostic and therapeutic strategies.

Lignin is insoluble in water, limiting its use in the synthesis of adhesives. Therefore, in order to increase the amount of lignin raw materials used in the synthesis of adhesives, a kind of aminated lignin compounds was prepared through lignin amination reaction, and conducting structural analysis in this paper. The particle size of the amino lignin is about 100 nm, with the weight average molecular weight of 57,627 g/mol and a water solubility of 0.45g/100ml. The reaction mechanisms were proposed that the phenolic hydroxyl groups of lignin react with ammonia molecules, and thereby successfully introducing amino groups to generate the aminated lignin compounds. Therefore, this article enriches the scientific theory of lignin reactions and provides reference for the widespread application of lignin raw materials in the field of adhesives.

Elevated immunoglobulin E (IgE) levels are commonly associated with allergies. However, high IgE levels are also found in several other infectious and non-infectious disorders. Elevated IgE levels typically suggest allergies, eczema, or recurrent skin infections. Very high IgE levels are uncommon in patients with active eczema but typically reflect a monogenic atopic condition or inborn immune defects with an atopic phenotype. The aim of our research is to identify if the possible cause of high IgE levels is also dependent on external factors, age, or associated recurrent pathologies such as infections. To answer this question, we performed a one-year retrospective study that included 200 hospitalized children who had at least two viral or bacterial infections in the six months preceding hospitalization. Measurements of IgE and allergen panels (respiratory and digestive) using blood samples revealed that individuals who tested positive for the body’s synthesis of hyperimmunoglobulin E were not observably allergic to any potential allergens despite having higher total serum IgE. According to the results, there was a strong correlation between elevated IgE serum levels and a history of infectious diseases among the patients.

Background: Molecular genetic events are among the numerous factors affecting the clinical course of papillary thyroid carcinoma (PTC). Recent studies have demonstrated that aberrant expression of miRNA, as well as different thyroid-related genes, correlate with the aggressive clinical course of PTC and unfavorable treatment outcome, which opens up new avenues for using them in personalization of the treatment strategy for patients with PTC. In the present work, our goal was to assess the applicability of molecular markers in preoperative diagnosis of aggressive variants of papillary thyroid cancer. Methods: The molecular genetic profile (expression levels of 34 different markers and BRAF mutation) was studied for 108 cytology specimens collected by fine-needle aspiration biopsy in patients with PTC having different clinical manifestations. Results: Statistically significant differences with adjustment for multiple comparisons (p &lt; 0.0015) for clinically aggressive variants of PTC were obtained for four markers: miRNA-146b, miRNA-221, FN1, and CDKN2A. Weak statistical correlation (0.0015&lt; р&lt;0.05) was observed for miRNA-31, -375, -551b, -148b, -125b, mtDNA, CITED1, TPO, HMGA2, CLU, NIS, SERPINA1, TFF3, and TMPRSS4. Conclusions: The recurrence risk of papillary thyroid carcinoma can be preoperatively predicted using miRNA-221, the fibronectin and cyclin-dependent kinase inhibitor 2A genes.

Background: Alfalfa, the most economically important forage legume worldwide, features modest genetic progress due to long selection cycles and large extent of non-additive genetic variance associated with its autotetraploid genome. Methods: To improve the efficiency of genomic selection in alfalfa, we explored the effects of genome parametrization (as autotetraploid and diploid dosage, plus allele ratios) and SNP marker subsetting (all available SNPs; only genic regions; only non-genic regions) on genomic regressions, together with various levels of filtering on reading depth and missing rates. We used Genotyping by Sequencing-generated data and focused on traits of different genetic complexity, i.e., dry biomass yield in moisture-favorable (FE) and drought stress (SE) environments, leaf size, and onset of flowering, assessed on 143 genotyped plants from a genetically-broad European reference population and their phenotyped half-sib progenies. Results: On average, allele ratio improved the predictive ability compared with other genome parametrizations (+7.9% vs. tetraploid dosage, +12.6% vs. diploid dosage), SNP subsetting offered an advantage compared with any tested subsettings (+3.7% vs. genic regions, +7.6% vs. non-genic regions). However, when focusing on specific traits, different combinations of genome parametrization and subsetting reached better performances. We also released Legpipe2, a SNP calling pipeline tailored for reduced representation (GBS, RAD) medium-sized genotyping experiments.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

In this study, Acısu Basin, which is upper side of one of the most important basins (Gediz) in Türkiye, was modelled using three types of hydrological models and three different calibration algorithms. Lumped (GR4J), semi-distributed (SWAT+), and fully distributed (mHM) hydrological models were built and integrated with Parameter Estimation Tool (PEST) which is a model independent calibration tool including various algorithms. Levenberg Marquardt (L-M), Shuffled Complex Evolution (SCE), and Covariance Matrix Adoption Evolution Strategy (CMA-ES) were selected as calibration algorithms. Calibration period was 1991-2000, and validation results were obtained for 2002-2005. The effect of model structure and calibration algorithm selection on discharge simulation was evaluated via comparison of 9 different model-algorithm combinations. Results have shown that mHM and CMA-ES combination showed the best discharge simulation performance according to NSE values (calibration: 0.67, validation: 0.60). Although statistically the model results were classified as acceptable, the pattern comparison of discharge value shows that all of the models miss the peak values in significant amounts. This problem may be related to the interventions made in 2000-2001 years interval and possible to overcome by changing the calibration and validation periods, increasing the number of iterations or using the naturalized gauge data.

Raru’s plants bark has long been used as traditional medicine in Batak’s tribe. Raru’s bark is derived from several trees that are usually used in a mixture in Batak traditional beverages. This bark is generally used as antidiabetic remedies. This study aims to combine the rarus’s bark extract and mocaf activated-carbon (MAC) in order to study antidiabetics in rats. The combination of raru’s bark extract and MAC were tested on male rats as of Sprague Dawley strain for testing antidiabetic bioactivity. The result showed that antidiabetic activity of raru’s extract and MAC exposed the antidiabetic level declines in rat’s blood. The various treatments of different concentration ratios of raru’s extract and MAC useful in the experiments showed that the levels of blood level reduction were slightly different (14-21%). The raru’s extract pure was observed more effective in decreasing the blood glucose level in rat’s blood, in comparison the positive control. The mixture of raru’s extract and MAC with 75:25 ratio is better than 50:50 ratio. The involvement of MAC in the alleged antidiabetic agent did little in improving the blood glucose level decrease in rat’s blood. Raru’s extract and MAC indicate its potential utilization as an antidiabetic agent.

Arabinoxylans (AXs) are non-starch polysaccharides with complex structures naturally occurring in grains (i.e., barley, corn, and others) providing many health benefits, especially as prebiotics. AXs can be classified as water-extractable (WEAX) and water-unextractable (WUAX) based on their solubility, with properties influenced by grain sources and extraction methods. A large body of evidence shows that AXs exert an im-portant health impact, including glucose and lipid metabolism regulation and immune system enhancement, which is induced by the interactions between AXs and the gut microbiota. Recent research underscores the dependence of AX physiological effects on structure, advocating for a deeper understanding of struc-ture-activity relationships. While systematic studies on WEAX are prevalent, knowledge gaps persist re-garding WUAX, despite its higher grain abundance. Thus, this review reports recent data on WUAX struc-tural properties (chemical structure, branching, MW) in cereals under different treatments. It discusses WUAX applications in baking and its benefits deriving from gut fermentation.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

K-band radar waves have high penetration and low attenuation coefficients. However, the wavelength of this radar wave is relatively short; thus, designing and preparing both broadband and wide-angle radar wave absorbers in this band presents considerable challenges. In this study, a resin-based K-band radar wave absorber with a biomimetic lotus leaf structure was designed and formed by UV curing. Here, microscale lotus leaf papillae and antireflection structures were prepared using a DLP 3D printer, and the contact angle between the material and water droplets was increased from 56° to 130°. In addition, the influence of the geometric parameters of the lotus leaf antireflection structure on the electromagnetic absorption performance and mechanical strength was investigated. After simulation optimization, the maximum electromagnetic loss of the lotus leaf structure 3D printed sample was −32.3 dB, and the electromagnetic loss was below −10 dB in the 20.8–26.5 GHz frequency range. When the radar incidence angle was 60°, the maximum electromagnetic loss was still less than −10 dB. The designed lotus leaf structure has a higher mechanical energy absorption per unit volume (337.22 KJ/m3) and per unit mass (0.55 KJ/Kg) than commonly used honeycomb lightweight structures during the elastic deformation stage, and we expect that the designed structure can be used as an effective lightweight material for K-band radar stealth.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

The gut microbiome known as the “hidden organ” in humans has received wide attention due to its pivotal role in human health, influencing various physiological functions and metabolic processes. Multiple factors influence the gut microbiome and diet emerging as a prominent determinant. Increasing evidence verifies different dietary patterns modulate gut microbial composition and its functionality. Asia, home to the world's largest population, showcases immense diversity, reflected in its complex dietary patterns influenced by tradition and modernization. A plethora of research evidence proves Asian diet confers beneficial effects on maintaining and improving health through favorable alteration of gut microbiome. Yet up to date, no comprehensive review exists on the influence of the Asian diet on gut microbiome. This review critically examines published data on dietary components from Eastern, Southeastern, Southern, Western and Central Asian diet and their interaction with the human gut microbiome across healthy and diseased states. It identifies strengths and limitations in Asian gut microbiome research. Asia experiences rapid dietary transitions demanding further investigation into their effects on the gut microbiota. However, evidence proves traditional Asian diets hold promise for developing personalized dietary interventions and therapeutics to promote gut health and prevent chronic diseases by modulating gut microbiome.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Forests have multifunctional roles. They not only increase forest carbon sinks through afforestation and management, but also indirectly realize multiple benefits of "economy + ecology + society". Therefore, we construct a multiple output-benefit system of forest carbon sinks based on the development of forest carbon sinks in provinces of China. This system is also able to distinguish the importance of forest carbon sinks from other outputs. For the efficiency evaluation of multi-level output systems, this paper constructs a cross-evaluation model based on evidential reasoning method, the original efficiency information by conducting efficiency evaluation before information fusion. Further, the spillover effects and influencing factors of forest carbon sink efficiency are analyzed through a spatial regression model to explore the spatial characteristics of forest carbon sink efficiency in China. The results show that: (1) there is a large gap between the cross-efficiency levels of forest carbon sinks in various regions of China, with significant spatial correlation. For the perspective of direct output benefits, the cross-efficiency of the eastern region is higher, while the cross-efficiency of the northwestern region is lower; for the perspective of indirect output benefits, the cross-efficiency of the southeastern region is higher. (2) China's forest carbon sink has a significant positive spillover effect, and the indirect output cross-efficiency has a significant negative impact on the forest carbon sink in its own region. Further analyzing the impact of indirect output cross-efficiency, it is found that the cross-efficiency of the ecological dimension and the cross-efficiency of the social dimension have a significant negative impact on the forest carbon sink in its own region, and the economic dimension has a significant positive impact on the forest carbon sink in its own region. In conclusion, corresponding policy recommendations are proposed for the development of forest carbon sinks to promote the realization of the dual-carbon goal.

While the number of publications on wine and health is steadily increasing, ranging from molecular level to epidemiological studies, often with contradictory results, little attention has been given to an holistic approach. In this review some unusual concepts are considered, such as phytocomplex, vehicle and the Matrix effect. As an example, three mono/polyphenols present in wine, Tyrosol, Hydroxytyrosol and Resveratrol, have been selected and the consequences of respecting, disregarding or ignoring the Matrix effect are shown. Underestimation of the wine Matrix effect could lead to deceiving results, as in the case of de-alcoholized wine or wine-compound-based nutritional supplements,or in emphasizing a single component toxic activity, in this case alcohol, ignoring the specific protective action at molecular level of other compounds (polyphenols) present in the same Matrix. The dark side of Matrix effect is also discussed. It is suggested that specificity of wine should be always taken in consideration by public health Authorities.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

High-spin states of 192Tl are populated by the heavy ion fusion-evaporation reaction 181Ta(16O, 5n)192Tl at 97 MeV beam energy. A new level scheme with eight new levels is constructed and the level spins are tentatively assigned. The negative-parity yrast band is extended up to 23^{-}\hbar. Subsequently, the systematics of signature splitting and signature inversion are discussed for the negative-parity yrast band of odd-odd Tl isotopes including 192Tl, 194Tl, 196Tl, and 198Tl. With the increase of neutron number signature inversion is found in 196,198Tl at high-spin state in these four Tl isotopes. The reason may be due to the competition between neutron-proton interaction and Coriolis force.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Knowledge is not merely the characteristic of certain pieces of information being deemed true, believed and justifiable, but rather a process. The sentences that reaches the status of knowledge forms a universe that provides an interpretation of the reality one aims to describe. Language exchanges information through communication and the justification, if concludes successfully with respect to a sentence, it elevates the information to the status of knowledge. We provide a model where we define the fundamental elements of communication and grammar. As a result, knowledge must be \open\ (everyone must be able to acquire it), \free\ (everyone must be able to justifiy) and \tidy\ (everyone must be able to retrace the justification process in all its parts recursively). Ultimately, the development of knowledge processing, referred to as \emph{knowmatic}, represents the evolution of the information technologies (\it).

Agrivoltaic agrotunnels are currently designed for high density grow walls that are not amenable to bush berries or root crops. Commercial grow bins provide deeper substrates for produce with more root systems but have high costs per unit growing area. To overcome the economic limitations of grow bins, this study applies the distributed manufacturing open-source design paradigm to develop four designs for low-cost open source structures. The designs target root vegetables and bush fruit specifically to be adopted by remote communities with limited or no outdoor growing environment to offset the market price for imported fresh produce. The indoor growing designs provide the necessary structure for supporting grow light and grow bins and enabled the transplanted berry plants to flower and produced fruits. They provide a comparable amount (110L) or more of grow volume from 106 to 192 L. The water reservoir volume for the commercial system (62 L) and grow area (0.5 m³) is surpassed by all new designs that range from 64 to 192 L and 0.51 to 0.76 m³, respectively. These superior properties are possible with material costs for all four designs that save more than 90% of the economic cost of the commercial systems.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

The use of omega-3 fatty acids (omega-3 FA) in the treatment of atopic dermatitis (AD) is an area of ongoing research. Some studies suggest that dietary supplementation with omega-3 FA can help manage symptoms of AD by reducing lesion severity, skin inflammation, dryness and itching, while other show no significant beneficial effect. The aim of this study was to evaluate the effect of omega-3 FA form fish oil in combination with GLA form blackcurrant seed oil in children with AD. This is a longitudinal, prospective, randomized, triple blind, placebo-controlled parallel clinical trial. The study was conducted during the 2-year period from autumn, winter, and spring avoiding the summer when AD usually improves. Children were randomized to receive the active study product (Mega Kid®) containing specific blend of omega-3 and omega-6 fatty acids or placebo. Primary outcomes were change in severity of AD measured using SCORing Atopic Dermatitis (SCORAD) patient oriented SCORAD (PO-SCORAD) and the difference in TCS use. Secondary outcomes were change in itch intensity, sleep quality and Family Dermatology Life Quality Index (FDLQI). Data were analyzed for 52 children (26 in the intervention group and 26 in the placebo group). In children receiving active product intention-to-treat analysis showed that after 4 months of treatment, there was a significant decrease in the SCORAD index (from median 42 to 25, p < 0.001) and use of topical corticosteroids (from median 30 to 10 mg/day, p < 0.001) but also significant improvement in itch, sleep quality and overall quality of life. Omega-3 fatty acids in combination with GLA and vitamin D has a great beneficial effect in treatment of atopic dermatitis in children. Therefore, we can conclude that supplementation with this specific combination could be considered a safe and effective intervention that can significantly reduce the severity of AD in pediatric patients.

Continuous-wave photocathode guns are capable of delivering electron beams with high repetition rates and high average currents. However, they are limited by relatively low accelerating gradients and cathode fields. This limitation leads to a larger beam size at the gun exit due to space charge forces, making the beam more sensitive to optical aberrations and posing challenges for low-emittance electron beam transmission. This paper focuses on the aberrations induced by multipole fields. We analyze the effects of quadrupole, sextupole, and higher-order fields on beam profile and transverse emittance and propose a beam-based method for the rapid characterization and correction of these multipole fields. Furthermore, we present an experimental study conducted on the DC-SRF-II photocathode gun equipped with dedicated correctors. Both simulation and experimental results demonstrate that our approach effectively mitigates beam aberrations caused by multipole fields, resulting in improved beam symmetry and reduced emittance.

(1) Background: Alzheimer’s Disease (AD) accounts for 70% of dementia cases and with no effective pharmacological treatments, new rehabilitation methods are needed. Motor activities and transcranial direct current stimulation (tDCS) have shown promise in stabilizing and enhancing cognitive functions. Objective: We want to investigate the effects of combined motor or cognitive activity with tDCS on cognitive functions in AD patients. (2) Methods: Patients with mild or moderate AD were randomized into four groups: motor activity or cognitive activity associated with anodic or sham tDCS (MotA, MotS, CogA, CogS). They received two weeks of treatment (45 minutes, 5 days/week), with the first 15 minutes using 2mA tDCS on the dorsolateral prefrontal cortex. Cognitive assessments were conducted pre-treatment (T0), post-treatment (T1), and one week after (T2). (3) Results: Twenty patients were included. Mann-Whitney test showed significant improvements in anodic groups (MotA+CogA) in the global cognitive status (p=.042), in selective attention (p=.012), and sustained attention (p=.012) at T1, but not at T2. In addition, MotA improved in the Picture Recognition Test (p=.027) and in sustained attention (p=.047) at T2. (4) Conclusion: Combined motor or cognitive activity with anodic tDCS could slow cognitive decline in AD patients, with notable improvements in global cognitive state and attention at T1.

Background/Objectives: Endocrine disruptors are ubiquitous agents in the environment and are present in everyday consumer products. These agents can interfere with the endocrine system, and subsequently the reproductive system, especially in pregnancy. Increasing research has been conducted to discover and describe the health effects of these agents on humans, including pregnant women, their fetuses, and the placenta. This review discusses prenatal exposure to various endocrine disruptors focusing on Bisphenols, Phthalates, Organophosphates, and Perfluoroalkyl substances, and their effects on pregnancy and fetal development. Methods: We reviewed the literature via PubMed and EBSCO databases and included the most relevant studies. Results: Our findings reveal that several negative health outcomes were linked to endocrine disruptors. However, despite the seriousness of this topic and the abundance of research on these agents, it remains challenging to draw strong conclusions about their effects from the available studies. This does not allow for strong, universal guidelines and might result in poor patient counseling and heterogeneous approaches to regulating endocrine disruptors. Conclusion: The urgency of the matter calls for urgent efforts, as more studies are needed in this realm, to protect pregnant patients ultimately and in the long term, society.

Pigmented corn is a gramineae food of great biological, cultural and nutritional importance for many Latin American countries, with more than 250 breeds in the American continent. It confers a large number of health benefits due to its diverse and abundant bioactive compounds. In this narrative review we decided to organize the information on the nutrients, bioactive compounds and phytochemicals present in pigmented corn, as well as their effects on human health. Phenolic compounds and anthocyanins are some of the most studied and representative compounds in these grasses, with a wide range of health properties, mainly the reduction of prooxidant molecules. Carotenoids are a group of molecules belonging to the terpenic compounds, present in a large number of pigmented corn breeds, mainly the yellow ones, whose biological activity incorporates a wide spectrum. Bioactive peptides can be found in abundance in corn, having very diverse biological effects that include analgesic, opioid, antihypertensive, etc. activity. Other compounds with biological activity found in pigmented corn are resistant starches, some fatty acids, phytosterols, policosanols, phospholipids, ferulic acid and phlobaphenes, as well as a great variety of vitamins, elements, and fibers. This review aims to disseminate and integrate the existing knowledge on compounds with biological activity in pigmented corn, in order to promote their research, interest and use by scientists, nutrition professionals, physicians, industries and the general population.

Objectives: Stress urinary incontinence (SUI) negatively affects the quality of life and sexual function in women. This study aimed to evaluate the efficacy of radiofrequency (RF) therapy in reducing SUI symptoms and its impact on sexual function. Methods: Thirty-four women with SUI were enrolled and underwent a single RF treatment session using the Viveve® System (Viveve Medical Inc., USA) with parameters of 90 J/cm² and 220 pulses per hour. Assessments at baseline and 6 months post-treatment included perineal ultrasound and personal interviews to evaluate lower urinary tract symptoms and sexual function. Urodynamic studies, voiding diaries, and questionnaires such as the Female Sexual Function Index (FSFI), Overactive Bladder Symp-tom Score (OABSS), Urogenital Distress Inventory-6 (UDI-6), Incontinence Impact Question-naire-7 (IIQ-7), and International Consultation on Incontinence Questionnaire-Short Form (ICIQ-SF) measured outcomes. Results: RF therapy significantly improved sexual function, with higher FSFI scores in all domains except pain at 6 months. SUI symptoms were significantly re-duced, as indicated by improved scores on OABSS, UDI-6, IIQ-7, and ICIQ-SF, alongside better voiding diary results. Anatomical changes included reduced bladder neck mobility, decreased vaginal width, and a reduced rotation angle of the proximal urethra. Conclusions: RF therapy is effective and safe for treating mild to moderate SUI and enhances sexual function, potentially due to changes in vaginal topography. These results suggest RF therapy as a viable non-surgical op-tion for managing SUI and improving sexual health.

A novel multicomponent glasses with nominal compositions of (50-x)MoO3:xWO3:25La2O3:25B2O3, x = 0, 10, 20, 30, 40, 50 mol% doped with 3 mol % Eu2O3 were prepared using a conventional melt quenching method. Their structure, thermal behavior and luminescent properties were investigated by Raman spectroscopy, differential thermal analysis and photoluminescence spectroscopy. Physical parameters as density, molar volume, oxygen molar volume and oxygen packing density were determined. Glasses are characterized with high glass transition temperature. Raman analysis revealed that the glass structure is built up mainly from tetrahedral (MoO4)2- and (WO4)2- units providing Raman bands of around 317 cm-1, 341-352 cm-1, 832-820 cm-1 and 928-935 cm-1. At the same time with the replacement of MoO3 with WO3 some fraction of WO6 octahedra are produced, which number increases with the increasing WO3 content. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (395 nm) excitation using the 7F0 →5L6 transition of Eu3+. PL emission gradually increases with increasing WO3 content evidencing that WO3 is more appropriate component than MoO3. The integrated fluorescence intensity ratio R (5D0 →7F2/5D0 →7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites.

Salinity stress emerges as an important menace to global food security, particularly affecting susceptible crops such as common bean plants (Phaseolus vulgaris L.). The disruption of ion balances caused by salt stress withing plants cells reduces water and nutrient absorption, and hampers growth and productivity. Sacchorhiza polyschides, a brown macroalga rich in essential elements, and macrominerals, has drawn attention as a natural biostimulant, being a potential remedy to bolster crop resilience against salt stress. This study delves into the effect of water extracts of Sacchorhiza polyschides (SPE) across varying concentrations (1%, 2%, and 5%) in common bean plants under salt stress (68.4 mM NaCl) conditions. Two different methods of application were used: by spraying the aerial part of the plant or by irrigation together with the watering solution. The effects of both systems of application were studied on the aerial parts of the plants. SPE exhibited significant enhancements in morphological parameters, chlorophyll content, carbon-nitrogen activities, and antioxidant enzymatic system activities, alongside increasing osmolyte accumulation, compared to salt-stressed plants without biostimulation. Moreover, SPE reduced reactive oxygen species (ROS) levels caused by salt stress, mitigating lipid peroxidation. The concentrations of 2% and 5% SPE applied by spraying showed the most significant results in most of the parameters analyzed. By shedding light on the underlying science behind this biostimulant effect, this research underscores the potential of SPE to enhance crop resilience and augment food production in salt-challenged environments.

Background: People with Down syndrome (DS) have a trisomy of chromosome 21 and marked deficits in verbal memory but relatively preserved visuospatial perception. Verbal memories are related to semantic knowledge. Little is known about the organization of semantic knowledge in people with DS, which was the aim of this study. Aims: The extent of false memory in people with DS was examined. Possible differences in the number of false memories induced by nominal and verbal themes were examined. Methods and Procedures: In the study phase, ten word lists with semantically related associates were presented. In the recognition phase, participants made judgments on whether each word had been represented previously as semantically related lures, old words, and semantically unrelated new words. Outcomes and Results: Differences in the processing of nominal and verbal theme-related lures were observed among people with DS. When processing nominal theme-related lures, people with DS showed delayed false positives. When processing verbal theme-related lures, people with DS showed no differences compared to controls. Similar patterns have been observed in people with DS when processing nominal theme-related associates and verbal theme-related associates. People with DS have delayed recognition of associates. When processing unrelated words, they showed significantly higher false positives than controls for both nominal and verbal eliciting themes. Further analyses of the themes revealed differences in false positives across syntactic categories among groups. Conclusions and Implications: People with DS showed a delayed recognition of associates and deviance in recognizing unrelated words in the nominal and verbal theme categories. People with DS were delayed in terms of nouns, but deviated with verbs in associated and unrelated words. Additionally, people with DS showed distinct patterns in processing five nominal lures and three verbal lures, suggesting that they formed false memories differently based on distinct syntactic categories. Thus, it was concluded that people with DS develop a deviant semantic structure. Category-based interventions for people with DS should be implemented in order to improve their semantic knowledge through lexical connections.

Leakage is important in groundwater cycle research and water resource management, the key is to construct the spatial distribution of aquitard. Influenced by natural and anthropogenic factors, the density of boreholes restricts the accuracy of aquitard structure. This paper explores the K-Nearest Neighbor (KNN) method to construct multi-layer aquitard structure in the hinterland of Songnen Plain, Northeast China, with limited boreholes, and compare it with Inverse Distance Weight (IDW) and Ordinary Kriging (OK) methods to evaluate the leakage. The KNN needs to first identify the eigenvalue-k of each layer, which is used to enhance the trainset to obtain the testset with a larger amount of sample data enhanced, and to make a prediction to obtain the 3-dimensional structure of aquitard. KNN is more accurate than the IDW and OK. The aquitrad structure obtained by the KNN is different from the IDW and OK, the thickness difference is 3.53%-54.00%, the area difference is 2.28%-23.91%, and the difference in leakage can be up to 24.51%. KNN also has a high degree of identification of aquitard edges, which can help the prevention of groundwater pollution. The results provide guidance for water balance analysis, borehole engineering design, water resources management and exploitation.

This study investigated the effectiveness of virtual reality (VR) technology in table tennis education compared to traditional training methods. A 12-week randomized controlled trial was conducted with 120 participants divided equally between VR and traditional training groups. Performance metrics, learning motivation, and satisfaction were assessed at regular intervals. Results demonstrated significant advantages of VR training, with the VR group showing superior improvements in serve accuracy (23.5% vs. 15.8%, p < 0.001), rally endurance (increase of 8.2 vs. 5.7 shots, p < 0.01), and overall skill scores (18.7 vs. 13.2 points improvement, p < 0.001). The VR group also exhibited higher increases in learning motivation (23.5% vs. 12.8%, p < 0.001) and satisfaction (31.5% vs. 18.7%, p < 0.001). Subgroup analysis revealed particular benefits for novice players and younger participants. These findings suggest that VR technology offers a promising approach to enhance table tennis education, potentially revolutionizing sports training methodologies. Future research should focus on long-term skill retention and the optimization of VR training protocols.

Under the new pattern of “double carbon” development, good ESG performance is the best way to promote the sustainable development of enterprises, and the ESG investment strategies are directly affected by the strategic vision of managers. Based on the upper echelons theory and stakeholder theory, this paper takes Chinese A-share listed companies from 2011 to 2022 as samples to empirically analyze the impact of managerial myopia on corporate ESG performance. The results show that managerial myopia significantly inhibits corporate ESG performance, mainly by inhibiting corporate green investment and green innovation sustainability. Furthermore, for state-owned enterprises (SOE), heavy polluting enterprises (HPE) and non-high-tech enterprises, the inhibitory effect of manager myopia on ESG performance is stronger. When the enterprise is in the growth stage, the above inhibition effect is more severe. For external governance, the greater the analyst attention and public environmental attention are, the more conducive they are to alleviating the restraining effect of managerial myopia on enterprise ESG performance. Therefore, effectively improving the time cognition level of managers and strengthening external supervision have become important measures for comprehensively optimizing the ESG performance.

While numerous studies have explored the correlation between the built environment and ride-hailing demand, few have assessed their nonlinear interplay. Utilizing ride-hailing order data and multi-source built environment data from Nanjing, China, this paper uses the machine learning method, eXtreme Gradient Boosting (XGBoost), combined with SHapley Additive exPlanations (SHAP) and Partial Dependence Plots (PDP) to investigate the impact of built environment factors on ride-hailing travel demand, including their non-linear and threshold effects. The findings reveal that dining facilities have the most significant impact, with a contribution rate of 30.75%, on predicting ride-hailing travel demand. Additionally, financial, corporate, and medical facilities also exert considerable influence. The built environment factors need to reach a certain threshold or within a certain range to maximize the impact of ride-hailing travel demand. population density, land use mix and distance to the subway station collectively influence ride-hailing demand. The results are helpful for TNCs to allocate network ride-hailing resources reasonably and effectively.

The COVID-19 pandemics has had an unprecedented global impact, and the COVID-19 mass vaccination campaign has been commonly regarded as crucial to overcome the pandemics. Since all-cause mortality is the best way to measure the consequences of a health intervention, the present study was devised to analyze the all-cause mortality data of the United Kingdom (UK), which are made publicly available broken down by vaccination status. Data from April 2021 to May 2023 were retrospectively collected and analyzed according to age groups and vaccination status and the Standardized Mortality Ratio (SMR) for all-cause mortality and for non-COVID-19 were calculated in comparison to the corresponding unvaccinated groups. Results show that, since an age group dependent date, the all-cause mortality SMRs were increasing in any of the age groups considered. Initially, the all-causes death SMRs were less than 1 for all age groups, but due to their growth, for the age groups 18-39, 80-89 and 90+ years by a certain date they exceeded the reference value. For the other age groups, as long as the trend is maintained, it is possible to predict the date in which the SMR would reach the value 1. Non-COVID-19 SMR values show a very similar trend. Their initial values much lower than 1 suggest the presence of significant biases in the ONS dataset which lead to an underestimation of the risks for those vaccinated, as it is not plausible that the vaccine protects from causes other than COVID-19. The finding that all-cause mortality SMRs in vaccinated in comparison to unvaccinated people increases over time requires careful examination to understand the underlying factors. Meanwhile, the other major countries should undertake a systematic collection of all-causes mortality broken down by vaccination status, and should be implemented a moratorium of the promotion of mass vaccination campaigns.

GABAA receptors are channel proteins crucial to mediating neuronal balance in the CNS. The structure of GABAA receptors allows for multiple binding sites and is key to drug development. Yet, the formation mechanism of the receptor’s distinctive pentameric structure is still unknown. This study aims to investigate the role of three predominant subunits of the human GABAA receptor in the formation of protein pentamers. Through purifying and refolding the protein fragments of the GABAA receptor α1, β2, and γ2 subunits, homopentamers were visualised with negative staining and Cryo-EM. To aid the analysis, AlphaFold2 was used to compare the structures. Results show that α1 and β2 subunit fragments successfully formed homo-oligomers, particularly homopentameric structures, while the predominant heteropentameric GABAA receptor was also replicated through the combination of the three subunits. However, it is still unclear whether γ2 subunits can form homopentamers or their main purpose is to bring together the α1 and β2 subunits to form GABAA receptors. Nevertheless, this study will lead to a deeper understanding of the atomic structure of GABAA receptors, especially in the formation mechanism of complex protein structures, and hopefully pave the way to the development of novel therapeutics for neuropsychiatric diseases.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

Renal cell carcinoma (RCC) accounts for approximately 90-95% of all kidney cancers in adults, with the clear cell RCC (ccRCC) the most frequently identified subtype. RCC is known for its responsiveness to immunotherapy, making it an area of significant research interest. Immune checkpoint (IC) molecules, which regulate immune surveillance, are established therapeutic targets in RCC. The aim of this study was to analyze the influence of polymorphisms in genes HVEM and CD160 on susceptibility to ccRCC and patient overall survival (OS) with over a ten-year period of observation. We genotyped three HVEM single nucleotide polymorphisms (SNPs): rs1886730, rs2234167, and rs8725, and two CD160 SNPs: rs744877 and rs2231375, in 238 ccRCC patients and 521 controls. Our findings indicated that heterozygosity within rs2231375 and/or rs2234167 increases ccRCC risk. Furthermore, in women, heterozygosity within additional HVEM SNPs, rs8725 and rs1886730, is associated with an increased ccRCC risk. The presence of a minor allele for rs1886730, rs2234167, rs8725, and rs2231375 was also correlated with certain clinical features of the disease. Moreover, the rs1886730 SNP was found to be associated with patients' OS. In conclusion, our study highlights an association between HVEM and CD160 polymorphisms and the risk of developing ccRCC as well as patient’s OS.

Fagao is one of China's traditional gluten free staple foods made by rice or corn flour. Corn Fagao prepared by co-fermentation with sourdough and yeast exhibits better quality and less staling compared to traditional yeast-fermented Fagao. The physicochemical properties of corn Fagao batter during the sourdough-yeast co-fermentation were investigated. The results showed that compared with yeast fermentation, the gas production and viscosity of the batter increased by co-fermentation. The co-fermented batter shows higher hydrolysis of starch and less amylose content. The integrity of starch granules in co-fermented batter was damaged more seriously, the crystallinity and short-range ordered structure were less than yeast fermented batter, even though the crystal structure type of starch did not change obviously. The peak viscosity, minimum viscosity, final viscosity, decay value and recovery value of corn batter are reduced by co-fermentation, which can improve the thermal stability of the batter and slow down the aging. Co-fermentation also results in a more pronounced reduction in protein subunit contents than yeast fermentation. The changes in the physicochemical properties of corn Fagao batter help explain the quality improvement of corn Fagao made from co-fermentation method, and may provide theoretical references for co-fermentation with sourdough and yeast to other gluten free foods.

We study theoretically the Josephson diode effect (JDE) realized in a system composed of parallel-coupled double quantum dots (DQDs) sandwiched between two semiconductor nanowires deposited on an s-wave superconductor surface. Due to the combined effects of the proximity-caused superconductivity, strong Rashba spin-orbit interaction and Zeeman splitting inside the nanowires, a pair of Majorana bound states (MBSs) may possibly emerge at opposite ends of each nanowire. Different phase factors arisen from the superconductor substrate can be generated in the coupling amplitudes between the DQDs and MBSs prepared at the left and right nanowires, and will result in the Josephson current. We find that the critical Josephson currents in positive and negative directions are different from each other in amplitude within an oscillation period with respective to the magnetic flux penetrating through the system, a phenomenon known as the JDE. It arises from the quantum interference effect in this double-path device, and can hardly occur in system of one QD coupled to MBSs. Our results also show that the diode efficiency can reach up to 50%, and depends on the overlap amplitude between the MBSs and the energy levels of the DQDs adjustable by gate voltages. The present model is realizable within current nanofabitication technologies and may find practical use in interdisciplinary field of Majorana and Josephson physics.

Purpose of research was to determine changes in optical quality for monthly disposable soft contact lenses (SCL) wearers with new and monthly worn SCL. Retinal straylight was assessed in SCL wearers using a C-Quant straylight meter. The study included 33 participants (age 22 ± 1.4 years) who wore monthly disposable silicone hydrogel contact lenses. Measurements were taken with month-old SCL that had been worn for no more than 4 hours. Participants then replaced the old lenses with new ones. After a 15-minute adaptation period, straylight measurements were taken with the new SCL. A questionnaire was administered to all participants, inquiring about vision complaints and the type of contact lens material used. The decimal logarithm of the stray-light parameter, log(s), was notably higher with month-old SCL (log(s) = 0.97±0.17) than with brand-new SCL (log(s) = 0.86±0.15), p < 0.001. The average increase in retinal straylight after a month of SCL use was log(s) = 0.11 ± 0.08. The questionnaire revealed that 35% of participants observed a reduction in visual quality after wearing the contact lenses for a month. Results showed that monthly disposable soft contact lenses could reduce visual quality when scheduled replacement time has been reached.

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P&lt;0.05), left hippocampus volume (LHV, β: -0.02435, P&lt;0.01) and right hippocampus volume (RHV, β: -0.02544, P&lt;0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P&lt;0.05) and LHV (β: -0.01173, P&lt;0.05) and RHV (β: -0.01193, P&lt;0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P&lt;0.05; RHV, β: -0.005527, P&lt;0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

Many farms are replacing the lighting with light emitting diode (LED) bulbs because of the technological modernization. We aimed to investigate the effects of incandescent light (IL) and LED lighting on Cobb500 broiler chickens for six weeks. Production parameters (body weight, feed consumption, feed conversion ratio), calculated slaughter values (yield%, relative breast%, thigh%) and breast meat quality parameters (pH at 45 min and 24 h postmortem, color, drip loss, kitchen equipment losses, shear force, meat composition) were recorded. Non-stop recordings were used to analyze the behavior of the birds in several periods of the rearing. LED group was significantly better in body weigh parameter between week 1-5 and feed conversion ratio between week 2-3. The most significant difference in behavior was observed in the middle of the rearing period. The chickens in the LED group spent more eating time, drinking time, interacting, and resting less. There was no difference in the meat quality parameters, only shear force was significantly lower in the LED group (1781.95±0.33 g/s vs. 2098.82±0.42 g/s). Based on our results, LED lighting can bring positive changes in animal production efficiency, behavior, and important characteristics for meat consumers.