To compare The effects of organic and inorganic impregnation on the properties of unmodified, phenol formaldehyde oligomer-modified (PFOMCF), and sodium silicate-modified Chinese fir wood (SSMCF) were compared using samples prepared using the respiratory impregnation method. Impregnation and reinforcement effects and water resistance of PFOMCF and SSMCF were compared and the results was showed that the weight percentage gain, density increase rate, bending strength, and compressive strength of SSMCF were clearly higher than those of PFOMCF and had a lower water absorption rate within 60 h. The impregnation and reinforcement effects and dimensional stability of SSMCF were better than those of PFOMCF. FT-IR, XRD, CONE, and TGA examinations were used to test and analyze the chemical structure, crystalline structure, flame retardancy, and heat resistance of these modified woods. The results indicated that SSMCF possessed more hydrogen bonds than PFOMCF and that Si–O–Si chemical bonding with high bond energy was formed. Meanwhile, the weakened degree of the diffraction peak of SSMCF was much less than that of PFOMCF. These results explained that the mechanical properties and water resistance of SSMCF were better than PFOMCF. Compared with PFOMCF, SSMCF had a lower heat release rate (HRR), peak-HRR, mean-HRR, total heat release, smoke production rate, and total smoke production as well as higher thermal decomposition temperature and residual rate. Inorganic sodium silicate was shown to be a better flame retardant, while SSMCF had good smoke suppression effects, thermal stability, and safety performance in the case of fire.

Excess nitrogen in agricultural drainage poses a serious threat to the water quality safety of the Yellow River basin. Utilizing aquatic plants to modify the rhizosphere microbial community structure and facilitate nitrogen transformation is a crucial strategy for mitigating regional water eutrophication. Our results revealed that the denitrification rate (DR), dissimilatory nitrate reduction to ammonium rate (DNRAR) and nitrogen fixation rate (NFR) of rhizosphere sediments exhibited a significant increase in artificially cultivated ditch. Compared with those in natural ditches, the richness of the bacterial community and the relative abundances of Bacteroidota, Verrucomicrobiota, Firmicutes, Anaeromyxobacter and Geobacter, which are involved mainly in the nitrogen cycle, in the rhizosphere sediments of artificially cultivated ditch were significantly greater due to improvements in environmental conditions. In artificially cultivated ditch, the dominant functional genes affecting DRNARs in the rhizosphere sediments of P. australis were nrfC and nrfA, while DRs were driven mainly by norB and napA, which were influenced by the nitrogen and carbon levels; and the dominant functional genes affecting NFRs in the rhizosphere sediments of T. orientalis were nifD, nifK and nifH. Our results provide a scientific basis for the use of aquatic plants for mitigating excess nitrogen levels in agricultural drainage.

The silver fir (Abies alba Mill.) is among the most valuable conifers in Europe for ecological and economic reasons. In the course of history, primarily in the 20th century, its share in stands has been declining due to ill-suited management practices, especially clear-cut management, air pollution, and wildlife-induced damage. Based on recent knowledge of fir ecology and population dynamics, small-scale shelterwood and selection management have been introduced in fir stands, which have also stabilized them. Fir is an essential species for maintaining high stability and biodiversity, especially on planosols and in waterlogged habitats. Due to its shade tolerance and environmental flexibility, particularly at higher altitudes, it can coexist very well with many tree species in mixtures, which can increase the productive potential of stands. It can form stands of heterogeneous structure, ranging from single to multi-layer to selection. For its successful natural regeneration, it is essential to reduce cloven-hoofed game and thus prevent bud browsing damage. On the other hand, fir is a species relatively resistant to bark stripping and the spread of secondary rot compared to Norway spruce (Picea abies [L.] Karst.). During global climate change, fir is expected to shift to higher elevations with sufficient precipitation, while in the southern part of its natural range or at lower elevations, outside water-influenced habitats, it is likely to decline. This paper essentially reviews the description and distribution of the species, its ecological requirements, threats and diseases, habitat and stand conditions, and close-to-nature forest management practices with emphasis on ongoing climate change.

To reveal the antibacterial effect of wound secretions of different Chinese fir strains on five kinds of bacteria. Three 3-year-old seedlings of Taxus chinensis var.koraiensis and Yangkou and the 3-year-old container seedlings of Taxus chinensis var.pendula, Yang061 and Yang020, were used as the research objects. The antibacterial effect of wound secretions was determined by the filter paper diffusion method, and the antibacterial effect was analyzed. Results showed that the wound secretions of different strains of Chinese fir bark had noticeable bacteriostatic effects on Bacillus subtilis, Salmonella paratyphi B, Pseudomonas aeruginosa, Escherichia coli, and Staphylococcus aureus. However, the bacteriostatic effects of different strains of Chinese fir secretions differed. The minimum inhibitory concentrations (MICs) of the wound secretions of different strains of Chinese fir against the five test bacteria differed. The mean MIC of Pseudomonas aeruginosa was the highest, and the mean MIC of Escherichia coli was the lowest. The antibacterial ability of the wound secretions of different Chinese fir strains was mainly determined by the composition of the wound secretions. There was no noticeable relationship with the number of wound secretions.

Nanocellulose (CNC) seems to be a promising surfactant, which, together with expandable graphite (EG), forms the essence of an effective natural-based fire retardant wood coating. In our research, the most suitable composition of the mixture was tested concerning good solubility, dispersion, and consistency. Favorable results were achieved with the formulation composed of a 4% CNC alkaline solution with 80 wt.% of selected EG. Subsequently, six different EG were used to prepare these wood fire retardant coatings. The effectiveness of treatments was verified using a test with a radiant heat source, where the test samples' relative weight loss, relative burning rate, and surface temperature during 600 sec were evaluated. All prepared formulations can be characterized as more or less equally effective. However, the best results were obtained with EG of GG 200 – 100 N, where the mass loss of the sample was 8.10 ± 1.24%. Very good results were also achieved by graphite 25 E + 180 HPH (8.70 ± 0.89%), which is similar to the previous one, even according to the microscopic assessment of the coating as well as the expanded layer. Graphite type 25 K + 180 (8.86 ± 0.65 %) shows the expanded layer's best cohesion, coating uniformity, and ease of application. The results of this work confirmed that the CNC coating itself has significant retardation effects.

The effectiveness of forest resources depends on the comprehensiveness and rationality of their consumption and processing into finished products. This article discusses a problem of utilising solid fir wood greenery residues generated during the industrial production of essential oils. Bioconversion is considered to be the most promising utilization method. The objective of this research was to study the chemical composition of bioconversion products of fir wood greenery-based substrates. The РР-3.2 strain of Pleurotus pulmonarius (Fr.) Quél was used as a biodestructor. In the process of bioconversion, the contents of polysaccharides and lignin substances is reduced to 38 and 28 % respectively. Up to 20 % of protein accumulates in bioconversion products of fir wood greenery. The amount of nucleic acids is not more than 1.5 g per 1 kg, the contents of heavy metals, such as mercury, cadmium, arsenic, lead, do not exceed maximum permissible concentration standards. The substrate weight loss reaches 15 %. When fallen leaves and post-extraction poplar bud residues are added to the substrate, the substrate-destroying activity of fungi rises, as well as the protein content increases by 3 %. The digestibility of products as a result of bioconversion increases 1.6–2.8 times depending on the substrate composition. The obtained data enable to recommend post-fermented substrates based on fir wood greenery and balsam poplar biomass for use as a protein feed additive.

Ulcerative colitis (UC) is a chronic inflammatory disease, the incidence of which is increasing worldwide. However, the etiology and pathogenesis of UC remains unclear. The n-butanol extract of pulsatilla decoction (BEPD) of the traditional Chinese medicine herbal formula has been shown to be effective in treating UC. We aimed to explore the molecular mechanism underlying the effects of BEPD on UC, in particular its effects on neutrophil extracellular trap (NET) formation by neutrophils. High-performance liquid chromatography was used to determine the principal compounds of BEPD. UC was induced in mice using dextran sodium sulfate, and mice were treated with 20, 40, or 80 mg/kg BEPD daily for seven days. Colonic inflammation was determined by assessing the disease activity index, histopathology, colonic mucosal damage index, colonic mucosal permeability, and pro- and anti-inflammatory cytokine levels. The infiltration and activation status of neutrophils in the colon were determined by analyzing the levels of chemokine (C-X-C motif) ligand (CXCL)1 and CXCL2, reactive oxygen species, Ly6G, and numerous NET proteins. Our results showed that BEPD improved the disease activity index, histopathology, and colonic mucosal damage index scores of mice with UC, and restored colonic mucosal permeability compared with untreated mice. The expression levels of the pro-inflammatory cytokines interleukin-1β, interleukin-6, and tumor necrosis factor-α in colon tissues were significantly decreased, while the expression levels of anti-inflammatory cytokines in colon tissues were significantly increased, exceeding those of control mice. In addition, BEPD reduce the expression of the neutrophil chemokines CXCL1 and CXCL2 in the colon tissue of mice with UC, reduced neutrophil infiltration, reduced reactive oxygen species levels, and significantly reduced the expression of NET proteins. BEPD also significantly reduced NET formation. The results of this study suggest that BEPD exerts therapeutic effects in a murine model of UC by inhibiting neutrophil infiltration and activation in the colon, as well as by inhibiting the expression of key proteins involved in NET formation and reducing NET formation, thereby alleviating local tissue damage and disease manifestations.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

The study examines the survival status of Scapharca broughtonii and Scallop Chlamys farreri under diverse seasons, sizes, and mixed breeding ratios. The objective is to explore the feasibility and economic benefits of the mixed breeding patterns of different shellfish varieties. The findings demonstrate that the overwintering mortality rate of mixed-cultured S.broughtonii ranges from 12.04% to 16.85%, which is conspicuously lower than that of individually cultured S.broughtonii. The summer mortality rate of mixed-cultured S.broughtonii with a size of 2.5 - 4.0 cm is significantly lower than that of individually cultured S.broughtonii (P < 0.05). There is no notable difference in the mortality between monoculture and polyculture of C.farreri. There is no significant disparity in the growth of C.farreri and S.broughtonii in monoculture and polyculture. The optimal polyculture size of the two scallops is 2.5 cm, and the ideal polyculture ratio is 1:1. The co-culture model of S.broughtonii and C.farreri in suspension cages has a high input-output ratio (1:1.9). It can effectively lower the winter and summer mortality rates of ark clams, representing an efficacious new methodology for marine shellfish farming.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

Dogs and cats have become the most influential and successful pets through long-term domestication. People keep them for various reasons, such as their functional roles or for physical or psychological support. However, why humans are so attached to dogs and cats remains unclear. A comprehensive understanding of the current state of human preferences for dogs and cats and the potential influential factors behind it is required. Here, we investigate this question using two independent online datasets and anonymous questionnaires. We find that current human preferences for dogs and cats are relatively higher than for most other interests, such as games and music. Genetic variations, gender, age, and economic development levels notably influence these preferences for dogs and cats. Specifically, dog and cat ownership is significantly heritable (h2 = 0.43, 95%CI: 0.35 -0.51) and further analysis found that women, young people, and those with higher incomes are more likely to keep dogs and cats, and the primary reason is to gain emotional support. Our study provides insights into why humans get so attached to dogs and cats and establishes a foundation for developing co-evolutionary models.

Objective: This research was aimed to estimate the anti-fatigue effects of arecoline and elucidate its underlying mechanisms using a murine model of central fatigue precipitated by sleep deprivation (SD). Methods: Seventy-two male C57BL/6 mice were randomly allocated into six groups: a control group, a SD-induced fatigue model group, a group receiving Rhodiola Rosea capsules (2.5 mg/kg), and arecoline groups administered low, medium, and high doses (10, 20, and 40 mg/kg, respectively). Following 28 days of continuous administrations, the effects of arecoline on the mouse fatigue-related behaviors was assessed by the behavioral tests, including grip strength, rotarod performance, and weight-bearing swimming endurance. Enzyme-linked immunosorbent assays (ELISAs) were utilized to measure the levels of the relevant biochemical markers. Western blotting was employed to quantify the expression of nuclear factor erythroid 2-related factor (Nrf2), Kelch-like ECH-associated protein 1 (Keap1), heme oxygenase 1 (HO-1), sequestosome-1 (p62), and NADPH quinone oxidoreductase 1 (NQO1) in the gastrocnemius muscle. Results: Arecoline administration notably enhanced grip strength, delayed the onset of fatigue as evidenced by extended latencies in rotarod tests, and increased the duration of weight-bearing swimming in mice. In the elevated plus maze, arecoline significantly reduced both the number of entries and the total distance traveled in the open arms. Arecoline markedly decreased serum levels of creatine kinase, blood urea nitrogen, lactate dehydrogenase, triglycerides, and cholesterol, while elevated total testosterone, lactate dehydrogenase, and immunoglobulin G levels. Furthermore, it significantly increased superoxide dismutase(SOD), catalase(CAT), and glutathione peroxidase activity in the gastrocnemius muscle, reduced malondialdehyde levels, augmented hippocampal SOD and CAT activity, and elevated glycogen stores in both liver and muscle tissues. Neurotransmitter levels were significantly increased, cytokine levels were markedly reduced, and the expression of Nrf2, Keap1, NQO1, p62, and HO-1 in brain tissue was significantly upregulated. Conclusion: The current study for the first time demonstrated that arecoline has significant anti-fatigue activity, and its mechanism of action is related to elevate the levels of glucose and lipid metabolism, relieve oxidative stress damage, inhibit neuroinflammatory response, regulate neurotransmitter levels and Keap1/Nrf2/HO-1 signaling pathway. The current study provides a new insight into the potential of arecoline in prevention and improvement of fatigue.

The research focuses on the production of particleboards from the biomass of energetic willow (Salix viminalis L.) and energetic poplar (Populus spp.), aiming to explore their feasibility as sustainable materials for various applications. Energetic willow and energetic poplar are known for their rapid growth and suitability for energy production. They present an intriguing alternative as raw materials with added value for particleboard manufacturing. The study investigates the selected mechanical and physical properties of the produced particleboards, considering parameters such as density profile, bending strength, modulus of elasticity, water absorption, thickness swelling, and screw withdrawal resistance. During the research, the results were also compared between different mass shares of willow and poplar particles in the particleboards. The findings underscore the promising potential of willow and poplar-based particleboards as eco-friendly alternatives in the construction and furniture industries, contributing to resource efficiency and carbon emission reduction efforts.

Determining the general-name-derived semantic relationships between geographic names often requires consulting many geographic name documents for verification. In geographic name translation and geographic name knowledge graphs, this method cannot meet the needs of large-scale extraction of general-name-derived semantic relationships between geographic entities. To solve this problem, this paper proposes a general-name derivation relation recognition method based on Prompt learning and Semantic Spatiotemporal Distribution Attention Feature Fusion (SSD-AFF). This method adopts a pipe-based relationship recognition strategy. First, the Prompt learning method is adopted to form a general-name derivation pattern with the general-name-derived geographical name category and the original geographical name category as the prompt word, and then the derivation pattern is combined with the geographical name as the input of the model so that the recognition problem of the general-name derivation of the geographical name can be transformed into a classification problem using the bidirectional language model. Then, by analyzing the characteristics of the semantic association and geographical spatio-temporal distribution between the general-name-derived geographical name and the original geographical name, the semantic spatio-temporal distribution characteristics of the general-name-derived geographical name are constructed. Finally, the network model based on the semantic spatio-temporal distribution Attention Feature Fusion (SSD-AFF) is used to distinguish the general-name-derived semantic relationships. The experimental results show that the proposed method has good performance. It can effectively mine the general-name-derived semantic relations between the vector data of geographical entities and has important application value in geographical name translation and geographical name knowledge maps.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

The aim of the study was to identify limiting factors for reusing wood through the recycling of window frames by conducting research under fully controlled conditions. The research involved manufacturing new window frames, seasoning them, and then shredding them into wood particles to prepare a three-layer particleboard. The proportion of wood particles in recycling was 0, 5, 10, 25, 50, and 100 parts by weight of the manufactured particleboard. Mechanical property tests were conducted: modulus of elasticity (MOE) and modulus of rupture (MOR), internal bond (IB), screw withdrawal resistance (SWR), and physical properties: density profile (DP), thickness swelling (TS) after water immersion, water absorption (WA), as well as formaldehyde emission and total volatile organic compounds (TVOC) tests. The conducted research indicates a significant potential for utilising wood from this sector of the wood industry, particularly considering variants with a higher proportion of recycled wood. MOR and MOE results are most promising for variants above 50 parts by weight of recycled wood. Based on the results obtained, it is clear that the production process should be improved or the raw material modified to enhance the internal bonding of particleboard, as these results were the weakest. Thus, recycled wood from window joinery has the potential to be reincarnated as particleboard, which continues to be widely used in their production.

Soft pneumatic actuators/robotics have received significant interest in the medical and health fields, due to their intrinsic elasticity and simple control strategies enabling desired interaction. However, current soft hand pneumatic exoskeletons often exhibit uniform deformation, mismatch the profile of the interacted objects, and seldom quantify the assistive effects during activities of daily life (ADL), such as extension angle and joint stiffness predicted. The lack of quantification poses challenges to the effective and sustainable advancement of rehabilitation technology. This paper introduces the design, modeling, and testing of pneumatic bioinspired Segmented Composite Proprioceptive Bending Actuators (SCPBAs) for hand rehabilitation in ADL tasks. The actuator’s soft-joint/rigid-bone segmented structure, inspired by the human finger anatomy, provides a superior fit compared to traditional continuous structures. A quasi-static model is established to predict the bending angles based on geometrical parameters. The SCPBAs also include a quantitative evaluation of joint stiffness and extension angle utilizing proprioceptive bending information. Additionally, a soft under-actuated hand exoskeleton equipped with SCPBAs demonstrates its potential in ADL rehabilitation scenarios.

This study describes a novel method for grading pathological sections of gliomas. Our own integrated hyperspectral imaging system was employed to characterize 270 bands of cancerous tissue samples from microarray slides of gliomas. These samples were then classified according to the guidelines developed by the World Health Organization, which define the subtypes and grades of diffuse gliomas. We explored a hyperspectral feature extraction model called SMLME-Resnet using microscopic hyperspectral images of brain gliomas of different malignancy grades. The model combines the channel attention mechanism and multi-scale image features to automatically learn the pathological organization of gliomas and obtain hierarchical feature representations, effectively removing the interference of redundant information. It also completes multi-modal, multi-scale spatial and spectral feature extraction to improve the automatic classification of glioma subtypes. The proposed classification method demonstrated high average classification accuracy (>97.3\%) and Kappa coefficient (0.954), indicating its effectiveness in improving the automatic classification of hyperspectral gliomas. The method is readily applicable in a wide range of clinical settings, offering valuable assistance in alleviating the workload of clinical pathologists. Furthermore, the study contributes to the development of more personalized and refined treatment plans, as well as subsequent follow-up and adjustment of treatment, by providing physicians with insights into the underlying pathological organization of gliomas.

In the ground-based infrared optical remote sensing system, the target signal is very weak due to the dynamic strong light background and the movement of small and small targets. In order to improve the limit detection capability, the background suppression and target enhancement methods are required to be more suitable for this scene. To solve this problem, we first analyze the image features in the current scene, and propose a more perfect point target and noise model. Then, we propose a new WY distribution function based on the Fermi Dirac distribution function, and propose an anisotropic filtering method based on this function, and further suppress the back-ground through the difference results of two steps. Then, based on the distribution function, we further designed an energy concentration accumulation strategy in 9 scale directions, through which the SNR of the target is effectively improved and the suppression ability of the background is enhanced. Through quantitative and qualitative experimental analysis, compared with the same type of algorithms, the proposed method has better robustness against extremely weak targets and dynamic backgrounds.

We developed an ovarian cancer-targeted drug delivery system based on a follicle-stimulating hormone receptor (FSHR) peptide. The lipophilic chemotherapeutic drug SN38 and the photosensitizer IR820 were loaded into the phospholipid bilayer of liposomes. Near-infrared laser irradiation stimulated the generation of reactive oxygen species, causing short-term reactive molecular species and spatial-temporal restricted photodamage to the biological targets. The reactive molecular species and spatial-temporal restricted photodamage enhanced the release and uptake of chemotherapy drugs and increased the sensitivity to chemotherapy drugs in ovarian cancer cells. FSH liposomes loaded with SN38 and IR820 (SN38/IR820-Lipo@FSH) were prepared using thin-film hydration-sonication. FSH peptide binding was analyzed using 1H NMR spectrum and Maldi-Tof. The average size and zeta potential of SN38/IR820-Lipo@FSH were 105.1 ± 1.15 nm (PDI: 0.204 ± 0.03) and −27.8 ± 0.42 mV, respectively. SN38/IR820-Lipo@FSH exhibited good drug-loading properties and the in vitro release was slow. FSH significantly increased the uptake of liposomes, inhibited cell proliferation, and induced apoptosis in A2780 cells. Moreover, SN38/IR820-Lipo@FSH exhibited good tumor-targeting ability and anti-ovarian cancer activity in vivo. The SN38/IR820-Lipo@FSH exhibited specific targeting to A2780 ovarian cancer cells. The combination of chemotherapy and photodynamic treatment based on an FSH peptide-targeted delivery system may be an effective approach to treating ovarian cancer.

The foraging behavior of ruminating ungulates significantly impacts forest ecosystems due to their nutritional requirements. This study focuses on inter-specific comparisons of bark browsing (stripping) between Douglas fir (Pseudotsuga menziesii (Mirb.) Franco) and silver fir (Abies alba Mill.). Field measurements were conducted at the previously established research-demonstration site "Husárik" in the Javorníky Mountains, north-western Slovakia. We didn’t only measure the sizes of wounds on stems but also assessed the dimensions of unrecovered parts of wounds, subsequently calculating areas of recovered bark patches. Then, the total areas of wounds, recovered patches, and unrecovered parts were determined. Additionally, the percentages of wound areas, recovered areas, and unrecovered areas were expressed as their proportions to the total bark surface. Influencing factors such as the position of wounds along the vertical stem profile and stem diameter class were analyzed using two- and three-way ANOVA followed by Fisher's LSD test. The results demonstrate the susceptibility of both tree species to bark browsing by ruminating ungulates, primarily red deer (Cervus elaphus L.) in our study site. Douglas fir exhibited slightly less intense browsing compared to silver fir, while silver fir had a slightly higher recovery rate. Specifically, 17.0% of the bark surface in Douglas fir and 21.5% in silver fir were browsed. The proportions of recovered areas on wounds were 62.5% and 69.6% in Douglas fir and silver fir, respectively. Regarding the vertical stem profile, the most intense browsing occurred at a height of 101-125 cm from the ground level, with rates of 40.7% in Douglas fir and 47.0% in silver fir. Browsing intensity showed negligible variation among diameter classes, which were classified as up to 35 mm, 35-50 mm, and over 50 mm. Our findings suggest that, as an introduced species, Douglas fir is not any suitable substitute for other commercially significant tree species in European countries where ruminating ungulates are overabundant.

Enormous quantities of softwood and hardwood tree bark are generated yearly in the pulp and woodworking industry. Chemical compounds which can be found in bark extracts have important biological properties and therefore a high potential for using in the production of special formulations. In the present study, extraction of Picea abies bark with organosolv solvents was investigated to achieve a high yield of desirable compounds. For the extraction four different solvent ratios of ethanol and water were applied. The temperature range of extraction was set between 40 and 100 °C and stirring velocity of 400 rpm. Extractions were performed with a solid/liquid ratio of 1:20. Yields of phenolics, flavonoids and tannins were determined using gallic acid for total phenolic content (TPC), quercetin for total flavonoid content (TFC) and tannic acid for total tannins content (TTC) as calibration compounds. Qualitative analysis of phenolic constituents was performed after their derivatization, by gas chromatography coupled with mass spectrometry identification. The total yield of bark extract of 14.75 wt.% was achieved by using an ethanol/water ratio of 50% (v/v) and a temperature of 100 °C. Gas chromatography results show 9 aromatic carboxylic acids as phenolic acids and quercetin and (+)-catechin as flavonoid compounds. Highest concentrations of TPC = 3.21 mg gallic acid equivalent/g, TCF = 0.62 mg quercetin equivalent/g and TTC = 0.84 tannic acid equivalent/g were determined at the same process conditions by photometric method. This study determined the conditions for organosolv extraction of useful compounds and suggests that some of extractives, e.g., taxifolin and rhamnetin presented in the spruce bark extracts, have antiviral (SARS-CoV-2) effects. Therefore, this warrants further evaluation of the antiviral properties of spruce bark constituents.

High level of noise is a disturbance to the human environment. Noise in industries is also an occupational hazard because of its attendant effects on workers’ health. Noise presents health and social problems in industrial operations, and the source is related to the machineries used in the industries. One of the unique features of the noise associated with wood machinery is the level of exposure and duration. Equipment used in a factory can be extremely loud. They can produce noise at decibels high enough to cause environmental health and safety concerns. The mechanically driven transport and handling equipment, cutting, milling, shaping and dust extractor installations in the wood industry generate noise. The sources of noise pollution have increased due to non-compliance with basic safety practices. The increased use of locally fabricated machine in the industry has increased the level of noise and vibration. The effects of industrial noise pollution as discussed include: increase in blood pressure; increased stress; fatigue; vertigo; headaches; sleep disturbance; annoyance; speech problems; dysgraphia, which means reading/learning impairment; aggression; anxiety and withdrawal. As presented in this paper, noise control techniques include; sound insulation, sound absorption, vibration damping and Vibration isolation.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

This study aims to test a model linking destination image, perceived value, tourist satisfaction, and tourist loyalty. Based on a sample of 300 tourists travelling by car from the World Natural Heritage Site of Tianchi, China, a new model of destination image was explored and data were analysed using partial least squares structural equation modelling (PLS-SEM). The results show that perceived value and satisfaction are direct antecedents of destination loyalty. Above all, perceived value and tourist satisfaction mediate the relationship between destination image and loyalty. Finally, this study discusses the theoretical and management implications of the findings in order to boost the tourism industry in the context of car trips.

Neurodegenerative diseases (NDDs) are a class of cognitive and motor disorders that include Alzheimer’s disease (AD), Parkinson’s disease (PD), Huntington's disease (HD), amyotrophic lateral sclerosis (ALS), and others. They are caused by lesions in cells and tissues of the central nervous system, resulting in corresponding dysfunctions and consequent decline in cognitive and motor functions. Neural tissues are extremely vulnerable to oxidative stress, which plays critical biological roles in NDDs. Aromatic compounds are found extensively in natural plants and have substantial effects of anti-oxidative stress damage, which not only have a wide range of research applications in cosmetics, foods, etc., but are also frequently utilized in the treatment of various central nervous system diseases. This review summarizes the relevant oxidative stress mechanisms in NDDs (AD, PD, HD, and ALS) and reviews aromatic compounds such as polyphenols, terpenoids, and flavonoids that can be used in the management of neurodegenerative diseases, as well as their specific mechanisms of antioxidant action. This review will serve as a reference for future experimental studies on neurodegenerative illnesses while also offering fresh insights into clinical therapy.

Hepatitis B surface antigen (HBsAg) is not only the biomarker of hepatitis B virus (HBV) infection and expression activity in hepatocytes, but also contributes to viral specific T cell exhaustion and HBV persistent infection. Therefore, anti-HBV therapies targeting HBsAg to achieve HBsAg loss are key approaches for HBV functional cure. In this study, we found that YZH-106, a rupestonic acid derivative, inhibited HBsAg secretion and viral replication. Further investigation demonstrated that YZH-106 promoted the lysosomal degradation of viral L- and M-HBs proteins. Mechanistic study by Biacore and docking analysis revealed that YZH-106 bound directly to PreS2 domain of L- and M-HBsAg, thereby blocking their entry to the endoplasmic reticulum (ER) and promoting their degradation in cytoplasm. Our work thereby provide basis for design of novel compound therapy to target HBsAg against HBV infection.

This article challenges the assumption that journals and peer review are essential for developing, evaluating and disseminating scientific and other academic knowledge. It suggests a more flexible ecosystem, and examines some of the possibilities this might facilitate. The market for academic outputs should be opened up by encouraging the separation of the dissemination service from the evaluation service. Publishing research in subject-specific journals encourages compartmentalising research into rigid categories. The dissemination of knowledge would be better served by an open access, web-based repository system encompassing all disciplines. There would then be a role for organisations to assess the items in this repository to help users find relevant, high-quality work. There could be a variety of such organisations which could enable reviews from peers to be supplemented with evaluation by non-peers from a variety of different perspectives: user reviews, statistical reviews, reviews from the perspective of different disciplines, and so on. This should reduce the inevitably conservative influence of relying on two or three peers, and make the evaluation system more critical, multi-dimensional and responsive to the requirements of different audience groups, changing circumstances, and new ideas. Non-peer review might make it easier to challenge dominant paradigms, and expanding the potential audience beyond a narrow group of peers might encourage the criterion of simplicity to be taken more seriously - which is essential if human knowledge is to continue to progress.

Lily tepals have a short lifespan. Once the tepals senesce, the ornamental value of the flower is lost. Some cultivars have attractive purple ovaries and fruits which greatly enhance the ornamental value of Asiatic hybrid lilies. However, little is known about the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries. To investigate the transcriptional network that governs purple ovary coloration in Asiatic hybrid lilies, we obtained transcriptome data from green ovaries (S1) and purple ovaries (S2) of Asiatic ‘Tiny Padhye’. Comparative transcriptome analysis revealed 4228 differentially expressed genes. Differential expression analysis revealed that nine unigenes including four CHS genes, one CHI gene, one F3H gene, one F3′H gene, one DFR gene, and one UFGT gene were significantly up-regulated in purple ovaries. One MYB gene, LhMYB12-Lat, was identified as a key transcription factor determining the distribution of anthocyanins in Asiatic hybrid lily ovaries. Further qPCR results showed unigenes related to anthocyanin biosynthesis were highly expressed in purple ovaries of Asiatic ‘Tiny Padhye’ at stages 2 and 3, while they showed an extremely low level of expression in ovaries of Asiatic ‘Yellow Pixels’ during all developmental stages. In addition, shading treatment significantly decreased pigment accumulation by suppressing the expression of several unigenes related to anthocyanin biosynthesis in ovaries of Asiatic ‘Tiny Padhye’. These results could further our understanding of the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries.

The samples from lunar farside have great significance for the study of the Moon, and even the solar system. Chang’e-6 landed successfully on the southern mare of the Apollo basin and returned ~2 kg samples from lunar farside. To provide a better understanding for the background of the returned samples, we conducted detailed crater size-frequency distribution (CSFD) measurements in the Chang’e-6 landing region, the southern mare of the Apollo basin. The southern mare is divided into western mare (W region) and eastern mare (E region), and then subdivided into five sub-units (W1, W2, W3, W4, W5) and three units (E1, E2, E3), respectively, according to the elevation, Ti and Fe abundances. Within the W2 and W5 region, more detailed sub-units were divided. The results show that the southern mare generally have two epochs, one of the Imbrian period and the other of the Eratothenian period. The basalt eruption lasted for ~1.7 Ga, from 3.28 Ga of the eastern mare to 1.54 Ga of the western mare. W region is younger than E region, while the three units of E region has an age of ~3.2 Ga. The ages of the western mare basalts range from 2.98 Ga to 1.54 Ga, lasting for 1.4 Ga. It’s worth noting that the age of the basalt at the Chang’e-6 sampling site is ~1.68 Ga, indicating the samples returned may include components with this very young age.

Against the background of the sky, imaging and perception of aircraft are cru- cial. Among these, the location of aircrafts is not a very difficult problem in general, because that deep learning algorithms and object detection models based on convolutional neural network(CNN) are ever-evolving. In order to have a better identification of various aircrafts, or to accurately locate different types of flying targets in the sky, it becomes significant to distinguish and recognize different types of aircrafts. One question is that, distinguishing and recognizing between sub-categories of aircrafts pose great challenges. Although fine-grained recognition focuses on exploring and studying such problems, aircrafts under different sub-categories and granularities lead us to rethink the application of features. We noticed that features in swin-transformer demonstrates the under- standing and processing of images, fully showcasing the encoding and indexing of information. Through this research and proposed approach, we discovered a better understanding of features encoding and use, which are inspired by the feature encoding and computation in swin-transformer. In our paper, our ap- proach has achieved effects on features encoded graphically, manifested from the architecture design and convolutional neural network computation, and outper- forms other famous fine-graiend classification models on this issue. Not only approach we proposed has demonstrated superior performance in fine-grained aicraft classification, but also the mechanisms of the feature encoding under different sample space partitions is revealed for this issue, which provides a re- search for the representation of aircraft fineness characteristics. The relationship between representation orientation of aircraft feature information under various grained divisions, shows that the recognition of different categories according to man-made, such as aircraft, can be achieved by means of the feature represen- tations studied in this paper, for more specific defined classification tasks and various man-made targets partition criteria, which may influences the princi- ple of design for calculation and feature extraction in fine-grained classification models.

Upholstery nonwoven fabric is a waste product mainly generated during upholstered furniture production. The polyester composition makes it problematic to recycle and reuse this product. This study examined the manufacturing process of nonwoven fabric-reinforced plywood composites and their selected mechanical and physical properties. Nonwoven fabric was integrated between veneers bound with urea-formaldehyde resin to improve standard layered composites' mechanical and physical properties. Several board variants were produced, differing in the position of the nonwoven layers in the composite structure. The composites were evaluated for modulus of rupture (MOR), modulus of elasticity (MOE), and screw withdrawal resistance, among others. The results showed that the addition of nonwoven fabric significantly improved some properties. Variants with strategically placed nonwoven layers showed the highest performance increases. The results underscore the potential of nonwoven fabric as an effective reinforcing material, offering a path to developing high-performance plywood composites suitable for demanding applications. Another, environmental profit is that the nonwoven fabric waste, that was used in tested plywood production, has not been subjected burning nor landfilling, but, by incorporation to plywood structure, have positively contributed to Carbon Capture and Storage (CCS) policy. The findings advocate for a circular economy approach, where industrial waste is effectively repurposed, contributing to the development of green materials in the wood-based composite industry.

Recycling upholstery textiles is challenging due to the complexity of materials, which often include a mix of fabrics, foams, and adhesives that are difficult to separate. The intricate designs and layers in upholstered furniture make it labor-intensive and costly to dismantle for recycling. Additionally, contaminants like stains, finishes, and flame retardants complicate recycling. Despite these difficulties, recycling upholstery textiles is crucial to reducing landfill waste and conserving resources by reusing valuable materials. It also helps mitigate environmental pollution and carbon emissions associated with producing new textiles from virgin resources. The presented research aimed to establish the feasibility of incorporating textile fibers from waste artificial leather fibers from the upholstery furniture industry into the structure of high-density fiberboards. This approach positively contributes to carbon capture and storage (CCS) policy and mitigates the problem of such waste being sent to landfills. The research shows that while selected mechanical and physical parameters of the panels decrease with a rising content of recycled textile fibers, it is possible to meet proper European standard requirements by adjusting technological parameters such as nominal density.

In the contemporary world of science, continuous observation of specific fixed regions is required, awaiting the emergence of targets or phenomena within those areas to locate and identify them. Astronomy requires continuous monitoring of stars, swiftly pinpointing occurrences, such as flares, and acquiring their spectral data to aid identification. In military contexts, continuous observation of specific areas is essential for promptly locating enemy movements and obtaining target spectral data for deciphering enemy disguises. Additionally, continuous observation of experimental samples in biochemistry is mandatory to pinpoint localized changes and acquire spectral data from those areas. Hence, this paper develops a novel imaging spectrometer solution to monitor localized regions continuously. Specifically, this paper first elaborates on the developed instrument’s characteristics and optical structure, followed by optical design software simulations. The instrument has an F-number of 5, a focal length of 100mm, and a field of view covering the wavelength range from 400nm to 600nm. The optical path diagram indicates that the system’s dispersion and imaging images can be separated, meeting the system’s requirements. Besides, the Modulation Transfer Function (MTF) graph confirms that the image quality meets the requirements. Furthermore, a region-monitoring type imaging spectrometer was constructed to assess the instrument’s capability for spectral observation of fixed regions. The instrument can detect a fixed area, with the target placed within the detection area. Spectral data were successfully obtained by conducting image processing on the acquired images. The correlation coefficient between this data and reference data was as high as 0.9226, indicating the instrument’s successful measurement of the target’s spectrum. Thus, the developed instrument demonstrated that it can image the observed areas and acquire spectral data from targets within those regions.

A method based on ultra performance liquid chromatography with diode array detector (UPLC-DAD) was developed for quantitative analysis of five active compounds and chemical fingerprint analysis of Rosa rugosa. Ten batches of Rosa rugosa collected from different plantations in the Xinjiang region of China were used to establish the fingerprint. The feasibility and advantages of the used UPLC fingerprint were verified for its similarity evaluation by systematically comparing chromatograms with professional analytical software recommended by State Food and Drug Administration (SFDA) of China. In quantitative analysis, the five compounds showed good regression (R²=0.999 5) within the test ranges and the recovery of the method was in the range of 94.2–103.8%. The similarities of the fingerprints of 10 batches of the samples were more than 0.981. The developed UPLC fingerprint method is simple, reliable and validated for the quality control and identification of Rosa rugosa. Additionally, simultaneous quantification of five major bioactive ingredients in the Rosa rugosa samples was conducted to interpret the consistency of the quality test. The results indicated that the UPLC fingerprint as a characteristic distinguishing method combining similarity evaluation and quantification analysis, can be successfully used to assess the quality and to identify the authenticity of Rosa rugosa.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Aiming at the development of the application of massive and heterogeneous LEO constellations, the influence of typical perturbation forces on the orbit prediction of LEO satellites at different altitudes is analyzed. Firstly, the main perturbation force model of LEO satellites is introduced. Then experiments for analyzing the influence of orbit prediction on LEO satellites at different altitudes are designed. Finally, the influence of typical perturbation forces on the orbit prediction under different prediction durations by numerical analysis is assessed systematically, and the orbit prediction of LEO satellites with different non-spherical gravitational field orders, ocean tide orders and atmospheric density models were compared and calculated. The research results show that different orders of non-spherical gravitational fields should be considered when the altitude of satellites is different, the reasonable gravitational field orders for LEO satellites at 500km, 1000km, 1500km and 2000km under 1-hour forecast time are 140x140, 80x80, 60x60 and 40x40 orders, the reasonable orders of ocean tide perturbation for 1500km and 2000km satellites are 20x20 orders. Under the 24-hour forecast time, atmospheric resistance has a great influence on the precision of LEO satellites at orbit altitude below 1,000km. The forecast deviation of the LEO satellites orbit at 500km reaches 8751.576m. The difference of orbit precision between different atmospheric density models is in the meter level. The orbit deviation by the Standard Atmosphere 1976 and NRLMSISE 2000 atmospheric models respectively reaches 25.494m. Relevant conclusions provide support for the optimization and selection of dynamical models in high precision orbit determination and fast orbit prediction of LEO satellites.

Banana wilt caused by Fusarium oxysporum f. sp. cubense tropical race 4 (Foc TR4) is a devastating fungal disease. Biocontrol strategies owned immense potential in inhibiting the spread of Foc TR4. Here, thirty actinobacteria were isolated from soils and screened for their antagonistic activity against Foc TR4. Strain SCA4-21T exhibited broad-spectrum antifungal activity against nine phytopathogenic fungi including Foc TR4. The strain was identified as the genus Streptomyces according to phenotypic characteristics and 16S rRNA gene phylogenetic analysis. Multi-locus sequence analysis based on five house-keeping gene alleles (atpD, gyrB, recA, rpoB, and trpB) revealed that strain SCA4-21T clustered into S. hygroscopicus subsp. hygroscopicus NBRC 13472T with 100% of bootstrap value. Average nucleotide identity and dDDH were 98.49% and 44.30% above the threshold of novel species. Hence, strain SCA 4-21T represented a novel species within the genus Streptomyces, named as Streptomyces luomodiensis sp. nov.. The type strain is SCA4-21T (=GDMCC4.340T= JCM36555T). By the CAZymes analysis, 348 carbohydrate-active enzymes were detected, including 15 chitinases and 8 β-1,3-glucanases. The fermentation broth of strain SCA4-21T showed high activities of chitinase and β-1,3-glucanase, contributing to the antifungal activity. Our results showed an innovative potential biocontrol agent for managing plant fungal diseases, specifically banana fusarium wilt.

Cortex Periplocae, as a traditional Chinese herbal medicine, has been widely used for autoimmune diseases, especially rheumatoid arthritis. Due to its potential pharmaceutical values, more studies about the biological activities of Cortex Periplocae have been conducted recently. Meanwhile, the adverse reaction of Cortex Periplocae is not a negligible problem in clinic. In this article, we reviewed a series of articles and summarized the recent studies of Cortex Periplocae in the areas of phytochemistry and pharmacology. More than 100 constituents have been isolated and identified from Cortex Periplocae, including steroids, cardiac glycosides, terpenoids, and fatty acid compounds. The crude extracts of Cortex Periplocae and its active compounds exhibit various biological activities, such as cardiotonic effect, anticancer action, and anti-inflammatory effect. This paper aims to provide an overall review on the bioactive ingredients, pharmacological effect, and toxicity of this plant. Furthermore, this review suggests investigating and developing new clinical usages according to the above pharmacological effects.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

The intelligent elderly care model places new demands on the skills of aging caregivers. The identification and development of forward-thinking, high-potential nursing talent is essential for advancing the intelligent elderly care sector. Multi-benchmarking selection and competitive analysis is used to evaluate and identify nursing personnel in the rehabilitation treatment center of a hospital in Hefei City. Using proxy evaluation and democratic evaluation model, three types of benchmarks such as single item benchmark, individual benchmark and group benchmark were identified and selected, and the professional nursing team was constructed based on the evaluation results. Different from the traditional other-directed evaluation, multi-benchmarking selection and competitive analysis is self-directed evaluation, this method is more conducive to the identification of high-potential and digital nursing talents by intelligent elderly service organizations, and facilitates the formation of professional nursing teams with complementary strengths and cross-fertilization, so as to satisfy the diversified and multi-level needs of the elderly for intelligent elderly services.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

Carbon (C) losses due to the conversion of natural forests adversely affect the abiotic components of terrestrial ecosystems. In tropical China, rubber cultivation often extends from its traditional range to elevations of up to 1400 m. However, C storage in rubber plantations across elevation gradients is poorly understood. In this study, we investigated biomass and C storage along elevation gradients in two age groups (8- and 12-year-old) of rubber monoculture plantations in Xishuangbanna, Southwest China. We investigated the C distribution across various tree sections, ranging from aboveground biomass (AGB) to belowground biomass (BGB), including litter, big dead branches, and different soil depths. A significant negative correlation was observed between total ecosystem C stocks and elevation in both age groups of rubber plantations. The highest ecosystem C stock of 197.90 Mg C ha–1 was recorded at 900 m in 8-year-old plantations, whereas in 12-year-old rubber plantations, the highest value of 183.12 Mg C ha–1 was found at 700 m. The total ecosystem C stocks decreased to its lowest level at 1000 m in both the 8-year-old and 12-year-old plantations, ranging between 113.05 Mg C ha–1 and 125.75 Mg C ha–1, respectively. We concluded that the total ecosystem C stocks were negatively correlated with elevation and significantly decreased from 8.05% to 51.55% and 11.46% to 42.96% between 700 m and 1100 m in both 8-year-old and 12-year-old plantations, respectively. However, no correlation was observed between the total soil C stocks and elevation in either age group of rubber plantations. Regardless of elevation gradient, the total ecosystem C stock of 12-year-old rubber plantations was 1.98% greater than that of 8-year-old rubber plantations. Biomass was the second largest contributor, while soil accounted for 82% to 90%, and the other factors contributed less than 2% of the total ecosystem C stock in both age groups. These fluctuations in C stocks along elevation gradients in both 8- and 12-year-old plantations suggested that rubber growth, biomass and C storage capacity decreased above 900 m and that age and elevation are key factors for biomass and C storage in monoculture rubber plantations.

Three-dimensional (3D) geological modeling technology offers intricate geological information services and technical support for the research of urban geological conditions and their evolutionary mechanisms. It further facilitates the analysis of environmental geological problems, encompassing their distinguishing features and genetic mechanisms. The precision of such three-dimensional models is predominantly influenced by the caliber of modeling data, the chosen modeling methodologies, and the intricacy of the modeled geological objects. This research, exemplified by the three-dimensional geological structure modeling of the Wuhan metropolitan development area, aims to explore a comprehensive three-dimensional modeling framework for urban geology, particularly in scenarios with large-scale and complex geological conditions. This study holds significant technical value in enhancing the application of 3D geological modeling, as well as practical importance for urban geological investigations and research.

In view of the fact that the field monitoring information can more intuitively and accurately reflect the stability state of slopes, this paper takes the warning threshold of slope deformation rate monitoring as the slope stability evaluation standard, and puts forward a method for solving the safety coefficient of rocky slopes. The discrete element method 3DEC, which is suitable for rocky slopes, is selected as the numerical calculation tool, and the convergence criterion of its strength reduction method is modified to the slope deformation rate threshold, and the method is realized by the bifurcation method through its built-in FISH programming language. The results of the classical case show that, by selecting the slope deformation rate threshold in the appropriate interval, the results of this paper's method are very close to those of the finite unit stress method and the limit equilibrium method, which verifies the reliability of this paper's method. Further, the method of this paper is applied to an open-pit mine slope project, based on the slope deformation on-site monitoring data, through the time series prediction method to determine the slope deformation rate warning threshold, using the threshold as an evaluation criterion to solve the slope's coefficient of safety, the calculation results show that: the slope's coefficient of safety in natural working conditions is 1.086, basically stable, suffered from continuous rainfall, the slope body is gradually saturated, the slope's coefficient of safety is reduced to 0.987, the slope's safety is reduced to 0.987. After continuous rainfall and gradual saturation of the slope, the coefficient of safety decreased to 0.987, destabilizing and destroying, which is consistent with the site conditions.

The development of one technology can be portrayed by common methods like Gartner’s hype cycle or S-curve, however, there is no method to characterize the feature distributions of multiple technologies within a specific domain. This study proposes a big data-based method in terms of four proposed features, namely versatility, significance, commerciality, and disruptiveness, to characterize the technologies within a given domain. The features of technologies are quantitively portrayed using the representative keywords and volumes of returned search results from Google and Google Scholar in two-dimensional analytical spaces of technique and application. We demonstrate the applicability of this method using 452 technologies in the domain of intelligent robotics. The results of our assessment indicate that the versatility values are normally distributed, while the values of significance, commerciality, and disruptiveness follow power-law distributions, in which few technologies possess higher feature values. We also show that significant technologies are more likely to be commercialized or causing potential disruption, as such technologies have higher scores in these features. Further, we validly prove the robustness of our approach via comparing historical trends with literature and characterizing technologies in reduced analytical spaces. Our method can be widely applied in analyzing feature distributions of technologies in different domains, and it can potentially be exploited in decisions like investment, trade, and science policy.

Abstract: Kiwifruit, a perennial horticultural crop known for its nutritional value, faces significant challenges due to biotic and abiotic stresses, affecting its yield and quality. Leucine-rich repeat receptor-like proteins (LRR-RLPs), a major group of receptor-like proteins in plants, have diverse functions in plant physiology, including growth, development, signal transduction, and stress responses. Despite their importance, the specific roles of kiwifruit LRR-RLPs in response to biotic and abiotic stresses remain poorly understood. In this study, we investigated the expression patterns of kiwifruit LRR-RLPs under various stress conditions, including pathogen stress, heat stress, waterlogging stress, and copper stress. Through genome and transcriptome analyses, we identified a total of 101, 164, and 105 LRR-RLPs in Actinidia Chinensis 'Hongyang', Actinidia eriantha 'Huate', and Actinidia chinensis 'Red5' kiwifruit, respectively, classified into 9 subgroups based on phylogenetic relationships. Synteny analysis revealed that the expansion of kiwifruit LRR-RLPs was primarily attributed to segmental duplication events. Using RNA-seq data from pathogen-infected kiwifruits, we identified specific LRR-RLP genes potentially involved in different stages of pathogen infection. Additionally, we observed the potential involvement of kiwifruit LRR-RLPs in abiotic stress responses, with upstream transcription factors possibly regulating their expression. Furthermore, protein interaction network analysis unveiled the participation of kiwifruit LRR-RLP genes in the regulatory network of abiotic stress responses. These findings highlight the crucial roles of LRR-RLPs in mediating both biotic and abiotic stress responses in kiwifruit, offering valuable insights for the breeding of stress-resistant kiwifruit varieties.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

Reducing fertilizer-N rate, applying nitrification inhibitor (NI), and incorporating straw are widely recommended to improve N use efficiency of crops and decrease N losses. However, how these practices affect crop N uptake by regulating the fertilizer-N fate during the growing season is not well understood. We conducted a field 15N tracer study to explore the effectiveness of reduced N application, NI, and straw incorporation on fertilizer-N fates for maize cultivation in Northeast China. The following six treatments were used: 1) no N fertilization (control); 2) 200 kg urea-N ha−1 (100%N); 3) 200 kg urea-N ha−1 and 2400 kg dry-straw ha−1 (100%N+S); 4) 160 kg urea-N ha−1 (80%N, i.e., 20% reduction of N fertilization); 5) 160 kg urea-N ha−1 and nitrification inhibitor (Nitrapyrin) (80%N+NI); 6) 160 kg urea-N ha−1, nitrification inhibitor and 2400 kg dry-straw ha−1 (80%N+NI+S). Our results showed that the five N fertilization treatments yielded 16%–25% more grain and 39%–60% more crop N uptake than the control receiving no N fertilizer, but the differences among the five treatments were not statistically significant. In contrast to plant growth, changes in fertilizer-N fates in soil and plant pools were more pronounced. Compared with the 100%N treatment, 20% fertilizer-N reduction (80%N) decreased 15N concentration in topsoil and plant pools but increased the proportion of plant 15N recovery at harvesting (N use efficiency, NUE15N, 60% vs. 50%) (P &lt; 0.05). Nitrapyrin co-application (80%N+NI) delayed soil nitrification and increased soil 15N retention at harvesting (52% vs. 36%), thereby decreasing NUE15N significantly (P &lt; 0.05). Straw incorporation (100%N+S) decreased fertilizer-N retention compared with NI co-application because it promoted NUE15N significantly (P &lt; 0.05). The combined application of NI and straw (80%N+NI+S) was more conducive to fertilizer-N retention in soil. Our findings demonstrate that NI and straw additions are efficient strategies for stabilizing fertilizer-N in soils and potentially minimizing N loss; however, their effects on NUE15N vary and the related mechanism must be further clarified in long-term trials.

Due to the accumulation of pesticides in the environment, the development of efficient strategies for their removal is of utmost importance. Activated carbons are currently seen as excellent candidates for adsorptive pesticide removal based on several beneficial properties, like a large surface area, developed porosity, and low price. However, a deep link between materials' properties and performance is still elusive. Here we focus on the kinetics of three organophosphate pesticides removal, aliphatic dimethoate and malathion and aromatic chlorpyrifos, using a series of carefully prepared activated carbon fibers. Used adsorbents have a wide range of specific surface areas, pore size distributions, and elemental content, allowing the establishment of the link between physicochemical properties and their performance as adsorbents. We use data analysis tools to link these properties and discuss their different roles in the removal of three structurally different yet extremely dangerous pesticides. The obtained results can guide the synthesis of novel adsorbents or rationally select adsorbents for specific target pollutants based on the physicochemical properties of adsorbents and the chemical structure of pollutants.

A key step in the study of tree pathology is the identification of appropriate method for inoculating pathogens of diseases in branch and trunk. Pathogens of diseases in branch and trunk are commonly inoculated through punching, burning, and toothpick inoculation. However, there is a lack of comparative analysis of the inoculation outcomes of these three methods. In this work, Six‐year‐old P. alba var. pyramidalis were inoculated with V. sordida, using punching, burning, and toothpick techniques, respectively, to investigate the differences in the effectiveness of these inoculation methods. Results reveal that the incidence rate was 93.55% in the toothpick inoculation group, significantly higher than 80.65% in the burning inoculation group (p = 0.007), while punching inoculation exhibited significant pathological responses in the early stages, with spontaneous healing in the later stage. Addi-tionally, toothpick inoculation was more efficient in inducing Valsa canker when inoculating the pathogen at the bottom of the tree, with lower intra‐ and inter‐row spacing (stand density) providing better outcomes than higher intra‐ and inter‐row spacing. The results of this study demonstrate that toothpick inoculation is an optimal option for studying the artificial inoculation of V. sordida in six‐year‐old P. alba var. pyramidalis, providing technical support for research on poplar diseases and offering a theoretical basis for the inoculation of other diseases in branch and trunk.

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

The flowering period of rice significantly impacts variety adaptability and yield formation. Properly shortening the reproductive period of rice varieties can expand their ecological range without significant yield reduction. Targeted genome editing, like CRISPR/Cas9, is an ideal tool to fine-tune rice growth stages and boost yield synergistically. In this study, we developed a CRISPR/Cas9-mediated multiplex genome editing vector containing five genes related to three traits: Hd2, Ghd7, and DTH8 (flowering stage genes), along with the recessive rice blast resistance gene Pi21 and the aromatic gene BADH2. This vector was introduced into the high-quality Geng rice variety in Zhejiang province, Jiahe212 (JH212), resulting in 34 T0 plants with various effective mutations. Among the 17 mutant T1 lines, several displayed diverse flowering dates, but most exhibited undesirable agronomic traits. Notably, three homozygous mutant lines (JH-C15, JH-C18, and JH-C31) showed slightly earlier flowering dates without significant differences in yield-related traits compared to JH212. Through special Hyg and Cas marker selection of T2 plants, we identified 7, 6, and 2 fragrant glutinous plants devoid of transgenic components, respectively. These single plants will serve as sib lines of JH212 and potential resources for breeding applications, including maintenance lines for Xian-Geng interspecific three-line hybrid rice. In summary, our research offers practical insights and potential resources for targeted improvement of Geng rice varieties, and would also promote the Geng rice varieties expending from the southward to the northward.

Ocean exploration is crucial for utilizing its extensive resources. Images captured by underwater robots suffer from issues such as color distortion and reduced contrast. To address the issue, we propose an innovative enhancement algorithm that integrates Transformer and Convolutional Neural Network (CNN) in a parallel fusion manner. Firstly, a novel transformer model is intro-duced to capture local features, employing peak-signal-to-noise ratio (PSNR) attention and linear operations. Subsequently, to extract global features, both temporal and frequency domain features are incorporated to construct convolutional neural network. Finally, the Fourier’s high and low-frequency information of the original image are utilized to fuse different features. To demon-strate the algorithm's effectiveness, underwater images with various levels of color distortion are selected for both qualitative and quantitative analyses. The experimental results demonstrate that our approach surpasses other mainstream methods, achieving superior PSNR and structural sim-ilarity index measure (SSIM) metrics and leading to a detection performance improvement of over ten percent.

PURPOSE: To investigate the oxylipin profiles in aqueous humor of primary open angle glaucoma (POAG) patients. METHODS: Aqueous humor samples were collected from 17 POAG patients and 15 cataract subjects and subjected to the liquid chromatography-mass spectrometry (LC-MS) analysis to detect the oxylipins. The prediction potential of the differential abundant oxylipins was assessed by the receiver operating characteristic (ROC) curves. Pathway and correlation analyses on the oxylipins and clinical and biochemical parameters were also conducted. RESULTS: The LC-MS analysis detected a total of 76 oxylipins, of which 29 oxylipins reached the detection limit. The multivariate analysis identified 5 differential abundant oxylipins, 15-keto-prostaglandin F2 alpha (15-kPGF2α), Leukotriene B4 (LTB4), 12,13-Epoxyoctadecenoic acid (12,13-Epome), 15-Hydroxyeicosatetraenoic acid (15-HETE) and 11-Hydroxyeicosatetraenoic acid (11-HETE). The 5 oxylipins are enriched in the arachidonic acid metabolism and linoleic acid metabolism pathways. Pearson correlation analysis showed that 11-HETE was positively correlated with intraocular pressure and central corneal thickness and negatively with cup/disk ratio in the POAG patients. In addition, 15-kPGF2α was positively correlated with visual field defect, and LTB4 was negatively correlated with macular thickness.  CONCLUSIONS: This study revealed the oxylipin profile in the aqueous humor of POAG patients. Oxylipins involved in arachidonic acid metabolism pathway could play a role in POAG and anti-inflammatory therapies could be potential treatment strategies for POAG.

The influence of growth temperature on the crystalline quality and optical properties of AlGaN at 325 nm, grown using plasma-assisted molecular beam epitaxy (MBE), was investigated. The growth temperature exhibited a significant impact on the growth mode and surface morphology. Specifically, at a growth temperature of 750 degrees Celsius, when appropriate Al and Ga flow rates were employed, the AlGaN layer exhibited exceptional surface morphology and favorable optical properties. The optical properties of the AlGaN material were explored, revealing the presence of two distinct non-radiative recombination centers characterized by different activation energies. The minority carrier lifetimes were measured as 560 ps at 10 K and 64 ps at room temperature. The underlying mechanism was analyzed from the perspective of carrier dynamics, shedding light on the observed phenomena.

This study addresses the critical challenge of Speech Enhancement (SE) in noisy environments, where the deployment of Deep Neural Networksolutions on microcontrollers is hindered by their extensive computational demands. Focusing on this gap, our research introduces a novel SE method optimized for MCUs, employing a 2-layer GRU model that capitalizes on perceptual speech properties and innovative training methodologies. By incorporating self-reference signals and a dual strategy of compression and recovery based on the Mel scale, we develop an efficient model tailored for low-latency applications. Our GRU-2L-128 model demonstrates a significant reduction in size and computational requirements, achieving a 14.2× decrease in model size and a 409.1× reduction in operations compared to traditional DNN methods like DCCRN, without compromising performance. This advancement offers a promising solution for enhancing speech intelligibility in resource-constrained devices, marking a pivotal step in SE research and application.

Water resources provided by alpine glaciers are an important pillar for people living in the arid regions in the west of China. In this study, the HBV (Hydrologiska Byrans Vattenavdelning) light model was applied to simulate glacier mass balance and runoff in the Koxkar River Basin (KRB) on the south slope of Mt. Tumur, western Tianshan Mts.. Daily temperature and precipitation were calculated by multiple linear regressions and gradient-inverse distance weighting, respectively, based on in-situ observed data by automatic weather stations (AWSs) in the basin (2007–2009) and at four meteorological stations neighbering the basin (1959–2009). Observed daily air temperature and precipitation were taken as input data for the HBV model, which was calibrated using runoff in 2007/08 and 2009/10, and validated in 2008/09 and 2010/11. Generally, the model could simulate runoff very well. The annual glacier mass balance and runoff were calculated using the HBV model driven by interpolated meteorological data for the period of 1959–2009. The simulated glacier mass balance were reasonable when compared with those observed values at nearby glaciers, indicating a decrease trend of mass balance in the basin with an average value of –370.4 mm a^-1 since 1959. The annual runoff showed a slight increase trend (5.51 mm a^-1). Futher analysis indicated that the runoff is more sensitive to temperature than precipitation amuont in the Koxkar river basin.

Recently, the concept of participatory democracy developed in the early 1970s has come back into fashion to revitalize the public involvement in political decision-making processes. Public par-ticipation in forest policy has been fully conceptualized by the scientific community in the late 1990s and early 2000s, but in many contexts the practical application remains unfulfilled. The aim of this study is to identify and analyze the participatory techniques used in literature to increase knowledge and facilitate its transferability into forest policies and strategies. A literature review was carried out to offer an overview of the participatory techniques adopted in the deci-sion-making process. At the end of literature review, 25 participatory techniques were identified based on over 2,000 publications. Afterwards, the participatory techniques were assessed using seven indicators (degree of participation, type and number of participants, time scale, cost, po-tential influence on policy). The results showed that the type of actors involved in the participa-tory technique is a key variable for the complexity and usefulness of the process, while the number of participants influences how information is disseminated. The Principal Component Analysis highlighted that the participatory techniques can be divided in three groups: the first group includes those techniques with a high degree of participation and a contextual high po-tential influence on policies, the second one includes techniques with a costs in terms of re-sources, while the third one consists of those with a large number of participants and reduced time requirements.

In recent decades, as eutrophication in inland and coastal waters (ICWs) has increased due to anthropogenic activities and global warming, so has the need for timely monitoring. Compared with traditional sampling and laboratory analysis methods, satellite remote sensing technology can provide macro-scale, low-cost, and near real-time water quality monitoring services. The Geostationary Ocean Color Imager (GOCI), integrated onboard the Communication Ocean and Meteorological Satellite (COMS) from the Republic of Korea, was the first geostationary ocean color observation satellite and was operational from April 1, 2011 to March 31, 2021. Over ten years, GOCI has observed oceans, coastal waters, and inland waters within its 2,500 km×2,500 km target area centered on the Korean Peninsula. The most attractive feature of GOCI, compared with other commonly used watercolor sensors, was its high temporal resolution (1h, eight times daily from 0 UTC to 7 UTC), providing the opportunity to monitor the quality of ICWs, where optical properties can change rapidly throughout the day. This systematic review aims to comprehensively review GOCI features and applications in ICWs, analyzing progress in atmospheric correction algorithms and water quality monitoring. Analyzing 123 articles from the Web of Science and China National Knowledge Infrastructure (CNKI) through a bibliometric quantitative approach, we examined GOCI’s strength and performance with different processing methods. These articles reveal that GOCI played an essential role in monitoring the ecological health of ICWs in its observation area in East Asia. GOCI has led the way to a new era of geostationary ocean satellites, providing new technical means for monitoring water quality in oceans, coastal zones, and inland lakes. We also discuss the challenges encountered by geostationary satellites in monitoring water quality and provide suggestions for improvements.

To address the response of small RNAs (sRNAs) biogenesis to drought stress, we identified sRNAs biogenesis genes, including 11 encoding argonauts (AGO), 8 encoding dicer-like proteins (DCL), and 9 encoding RNA-dependent RNA polymerases (RDR) in the peach genome. Notably, the largest numbers of sRNAs biogenesis genes are located to chromosome 1. The PAZ, PIWI, and MID domains were identified in PpAGOs, while the ribonuclease IIIa and IIIb domains were characterized in PpDCLs. The RDRP domain was recognized in PpRDRs. Orthologous similarity and collinearity analyses between Arabidopsis and peach revealed 5, 1, and 2 collinear blocks in AGOs, DCLs, and RDRs, respectively. Moreover, 41, 40, and 42 cis-acting elements were located in the promoters of PpAGOs, PpDCLs, and PpRDRs, respectively, with the majority related to drought stress response. Analysis of RNA sequencing (RNA-seq) data revealed that sRNAs biogenesis genes were involved in drought stress response in different tissues. Furthermore, the expression of candidate genes was verified in two peach cultivars, Beijing 2-7 (BJ2-7) and Sinai (SN), which are drought tolerance and sensitive, respectively. Interestingly, the expression of PpAGO2b, PpDCL2b, PpDCL4, and PpRDR4 genes was induced in ‘BJ2-7’ but inhibited in ‘SN’ under drought stress. Overall, this study provides insight into the roles of sRNA biogenesis genes in response to drought stress in peach.

The Tibetan Plateau(TP) is known as ‘the water tower of Asian’, its precipitation variation play an important role in the eco-hydrological processes and water resources regimes. based on the monthly mean precipitation data of 65 meteorological stations over the Tibetan Plateau and the surrounding areas from 1961-2015,variations, trends and temporal-spatial distribution were analyzed, furthermore, the possible reasons were also discussed preliminarily. The main results are summarized as follows: the annual mean precipitation in the TP is 465.54mm during 1961-2015, among four seasons, the precipitation in summer accounts for 60.1% of the annual precipitation, the precipitation in summer half year (May.- Oct.) accounts for 91.0% while that in winter half year (Nov.- Apr.) only accounts for 9.0%; During 1961-2015, the annual precipitation variability is 0.45mm/a and the seasonal precipitation variability is 0.31mm/a, 0.13mm/a, -0.04mm/a and 0.04mm/a in spring, summer, autumn and winter respectively on the TP; The spatial distribution of precipitation can be summarized as decreasing from southeast to northwest in the TP, the trend of precipitation is decreasing with the increase of altitude, but the correlation is not significant. The rising of air temperature and land cover changes may cause the precipitation by changing the hydrologic cycle and energy budget, furthermore, different pattern of atmospheric circulation can also influence on precipitation variability in different regions.

The dust originating from the extinct lake of the Aral Sea poses a considerable threat to the sur-rounding communities and ecosystems. The accurate location of these wind erosion areas is an essential prerequisite for controlling sand and dust activity. However, few relevant indicators re-ported in the current study can accurately describe and measure wind erosion intensity. A novel wind erosion intensity (WEI) of a resolution unit was defined in this paper based on the deformation due to the wind erosion in this resolution unit. We also derived the relationship between WEI and soil InSAR temporal decorrelation (ITD). The ITD is usually caused by the surface change over time, which is very suitable for describing wind erosion. However, within one resolution unit, the ITD signal usually includes soil and vegetation contributions, and few studies are referred to this. Therefore, we proposed an ITD decomposition model (ITDDM) to decompose the ITD signal of a resolution unit. The least-squares method (LSM) based on singular value decomposition (SVD) is used to estimate the ITD of soil (SITD) within a resolution unit. We verified the results qualitatively by the landscape photos, which can reflect the actual conditions of the soil. At last, the WEI of the Aral Sea from June 23, 2020, to July 05, 2020, was mapped. The results confirmed that (1) Based on the ITDDM model, the SITD can be accurately estimated by the LSM method, (2) the Aral Sea is experiencing severe wind erosion, and (3) The middle, northeast, and southeast bare areas of the South Aral Sea are where salt dust storms may occur.

(1) Background: Parents of children with autism spectrum disorders often experience psychological distress, which can affect the quality of childcare they provide. It is crucial to screen for psychiatric symptoms among these parents. The Core Symptom Index (CSI) is a widely used tool for assessing general symptoms such as depression, anxiety, and somatic symptoms, with demonstrated validity and reliability across various populations. However, there is limited research on the validity and reliability of the CSI in the general Chinese population. This study aimed to investigate the psychometric properties of the Chinese version of the CSI among parents of children with autism spectrum disorders using Confirmatory Factor Analysis (CFA). (2) Methods: A total of 794 Chinese parents raising children with autism participated in this study. All completed the CSI, along with the social inhibition subscale of the Interpersonal Problems Inventory and the Couple Satisfaction Index. Factorial validity was assessed using CFA to determine how well the bifactor three-factor model fits the data. Various structural models were compared using model fit indices. Convergent and discriminant validity were examined by exploring correlations with the social inhibition subscale and the Couple Satisfaction Index. Invariance testing of the CSI was conducted across multiple groups based on gender, age, and education using CFA. The reliability of the CSI was evaluated using McDonald’s omega coefficients. (3) Results: The bifactor model emerged as the best-fitting model for the data, suggesting that the total score of the CSI adequately represents overall psychiatric symptoms. The CSI exhibited significant correlations with the social inhibition subscale (r = 0.41, p &lt; 0.01) and smaller correlation coefficients with the Couple Satisfaction Index (r = -0.16, p &lt; 0.05), indicating both convergent and discriminant validity. Invariant tests supported scalar invariance levels based on gender and age but only partial invariance for education. The Chinese version of the CSI demonstrated high consistency, with McDonald's omega coefficients ranging between 0.86 and 0.95. (4) Conclusions: The bifactor model of the Chinese version of the CSI is validated, making it a suitable tool for measuring depression, anxiety, and somatization symptoms among parents of children with autism spectrum disorders. Further research on other Chinese populations is encouraged.

Timely and accurate acquisition of information on distribution of the crop planting structure in Loess Plateau of eastern Gansu Province, one of the most important agricultural areas in western China, is crucial for promoting fine management of agriculture and ensuring food security. In this study, the Object-Based Image Classification (OBIC), the Random Forest (RF) and Convolutional Neural Network (CNN) models were employed to classify the crop planting structure of four representative test areas in Qingyang City in a precise manner. Firstly, different optimal segmentation scales for various crops were selected using the Estimation of Scale Parameter 2 (ESP2) tool and the Ratio of Mean Difference to Neighbors(ABS) to Standard Deviation (RMAS)model. The images were then segmented through multiresolution segmentation combined with the Canny Edge Detection algorithm. Secondly, the L1 regularized logistic regression model was utilized to select and optimize 39 spatial feature factors including spectral, textural, geometric, and index features, in conjunction with phenological factors. Lastly, under the multi-level classification framework, the Random Forest (RF) classifier and Convolutional Neural Network (CNN) model, combined with object-based multiresolution segmentation, was used to classify the crop planting structure. The findings show that: Thanks to the Canny Edge Detection algorithm, we can obtain a more complete boundary of the segmented objects and improve the separability. The optimal segmentation scales for corn, vegetables, and buckwheat were found to be 55, 70, and 35, respectively, while wheat and apple had optimal segmentation scales of 65. In addition to phenological characteristics, the number of selected spatial features for corn, vegetables, buckwheat, wheat, and apple were 9, 7, 16, 12, and 10, respectively. The CNN model demonstrated high consistency with the RF model in the classification results, but the accuracy of RF model is higher than that of CNN model on the whole. The overall accuracy of classification using RF model in four test areas registered 91.93%, 94.92%, 89.37% and 90.68%, respectively. This paper introduced crop phenological factors, effectively improving the extraction precision of shattered agricultural planting structure in the Loess Plateau of eastern Gansu Province. Its findings have important application value in crop monitoring, management, food security and other related fields.

Autonomous weapons systems (AWS), sometimes referred to as “killer robots”, are receiving evermore attention, both in public discourse as well as by scholars and policymakers. Much of this interest is connected with emerging ethical and legal problems linked to increasing autonomy in weapons systems, but there is a general underappreciation for the ways in which existing law might impact on these new technologies. In this paper, we argue that as AWS become more sophisticated and increasingly more capable than flesh-and-blood soldiers, it will increasingly be the case that such soldiers are “in the power” of those AWS which fight against them. This implies that such soldiers ought to be considered hors de combat, and not targeted. In arguing for this point, we draw out a broader conclusion regarding hors de combat status, namely that it must be viewed contextually, with close reference to the capabilities of combatants on both sides of any discreet engagement. Given this point, and the fact that AWS may come in many shapes and sizes, and can be made for many different missions, we argue that each particular AWS will likely need its own standard for when enemy soldiers are deemed hors de combat. We conclude by examining how these nuanced views of hors de combat status might impact on meaningful human control of AWS.

As the world’s second-largest economy, China has undergone rapid industrialization and urbanization, leading to high energy consumption and significant carbon emissions. This development has exacerbated conflicts between human-land relations and environmental conservation, contributing to global warming and urban air pollution, both of which pose serious health risks. This study utilizes nighttime light (NTL) data from 2005 to 2019, combined with scaling techniques and statistical analysis, to estimate city-scale energy carbon emissions over a 15-year period. Our focus is on Northeast China, a traditional industrial region comprising 36 cities across three provinces, rich in natural resources but now facing severe aging challenges. We analyzed the spatial patterns of energy carbon emissions, while spatiotemporal evolution was assessed through spatial autocorrelation and dynamic changes. These dynamic changes were further evaluated using standard deviation ellipse (SDE) parameters and SLOPE values. Additionally, we examined the conflict between city-scale emissions and economic growth using the Tapio decoupling index. Our findings for the 36 cities over the 15-year period include: (1) Heilongjiang shows low emissions with a downward trend; Jilin shows overall improvement; Liaoning has high and steadily increasing emissions. (2) The global spatial autocorrelation of energy carbon emissions is significant, with a positive Moran’s I, while significant local Moran’s I clusters are concentrated in Heilongjiang and Liaoning. (3) The SDE shows the greatest changes in city-scale emissions occurred in 2015, followed by 2019, 2005, and 2010. (4) Emission growth across the 36 cities is fastest in Heilongjiang, followed by Liaoning and Jilin. (5) Tapio decoupling analysis shows overall positive decoupling in Heilongjiang, a decline in decoupling quality in Jilin, and no significant change in Liaoning. Finally, we recommend strategies to reduce emissions from the perspectives of government, industry, and residents. This research offers a quantitative foundation for achieving dual carbon goals and supports the implementation of policies focused on energy transition and sustainable urban planning.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

The peptide hormone kisspeptin attenuates liver steatosis, metabolic dysfunction-associated stea-tohepatitis (MASH) and fibrosis in mouse models, by signaling via the kisspeptin 1 receptor (KISS1R). However, whether kisspeptin impacts fibrogenesis in the human liver is not known. We investigated the impact of a potent kisspeptin analog (KPA) on fibrogenesis using human precision cut liver slices (hPCLS) from fibrotic livers from male patients, in human hepatic stellate cells (HSCs), LX-2 and in primary mouse HSCs. In hPCLS, 48 h and 72 h of KPA (3 nM, 100 nM) treatment decreased collagen secretion, and lowered expression of fibrogenic and inflammatory markers. Immunohistochemical studies revealed that KISS1R is expressed and localized to HSCs in MASH/fibrotic livers. In HSCs, KPA treatment reduced transforming growth factor beta (TGFb)-induced expression of fibrogenic and inflammatory markers, in addition to decreasing TGFb induced collagen secretion, cell migration, proliferation and colony formation. Mechanistically, KISS1R signaling downregulated TGFb signaling by decreasing SMAD2/3 phosphorylation, via activation of protein-phosphatases PP2A, that dehosphorylates SMAD 2/3. This study revealed for the first time that kisspeptin reverses human hepatic fibrogenesis thus identifying it as a new therapeutic target to treat hepatic fibrosis.

Recent interest in preventing the development of osteoporosis has focused on the regulation of redox homeostasis. However, the action of lycopene (LYC), a strong natural antioxidant com-pound, on osteoporotic bone loss remains largely unknown. Here, we show that the administra-tion of LYC to OVX rats reduces body weight gain, improves lipid metabolism and preserves bone quality. In addition, LYC treatment inhibits ROS overgeneration in serum and bone marrow in OVX rats, and in BMSCs upon H2O2 stimulation, leading to inhibiting adipogenesis and pro-moting osteogenesis during bone remodeling. Mechanically, LYC may improve bone quality via an increase in the expressions of FoxO1 and Runx2, and a decrease in the expressions of PPARγ and C/EBPα in OVX rats and BMSCs. Collectively, these findings suggest that LYC attenuates osteoporotic bone loss through promoting osteogenesis and inhibiting adipogenesis via regula-tion of the FoxO1/PPARγ pathway driven by oxidative stress, presenting a novel strategy for os-teoporosis management.

Dust storms play a crucial role in the climate system and the space environment of Mars and have a great impact on human’s Mars exploration activities. The Martian dust storms exhibit significant regional, seasonal and interannual variations due to various controlling factors such as the large-scale atmospheric circulation, varying solar radiation forcing, and Martial orbital and rotational motions and their coupling to the atmospheric dynamics. This paper focuses on the review of cur-rent understandings on Martian dust storms. This paper begins by elucidating the basic properties of dust storms, and their driving mechanisms and impacts on atmospheric dynamics, atmospheric electric property, space environment, topography, and Mars explorations. Then it introduces the observation methods on different platforms including orbiters and landers/rovers, and the da-tasets constructed based on these historical observations for Martian dust storms. Finally, we pro-posed the dust storm monitoring and forecasting for the upcoming Chinese Tianwen-3 Mars sam-pling returning mission. It concludes by depicting the future research topics to systematically un-derstand the Martian dust storms.

Coilia nasus is an important fish resource in the Yangtze River, and the Yangtze River Estuary is a crucial migration pathway for it. In this study, we used otolith microchemistry to analyze the strontium/calcium (Sr/Ca) ratios and Sr contents in the sagitta otolith of C. nasus from the south branch (SB) and north branch (NB) of the Yangtze River Estuary, and obtained the diversity of migration patterns and spawning grounds distribution for C. nasus. The results indicate that C. nasus from both branches include two types of habitat history: freshwater (F)-brackish water (B) (Type I) and F-B-seawater (S) (Type II), with Type I being dominant at 62.50% in both branches. The C. nasus from SB comprises six migration patterns, while that from NB has seven migration patterns. The C. nasus from both branches hatch in F habitats. At the time of capture, the C. nasus from SB predominantly remain in F, accounting for 62.5%, while C. nasus from NB primarily stay in B, accounting for 87.5%. Throughout the migration process, C. nasus from both branches switch between different habitats, with C. nasus from NB exhibiting more frequent transitions between F and B, showing a greater reliance on the estuarine brackish habitat. The radius of the first blue region near the core (Lf) and freshwater coefficient (Fc) of otolith for C. nasus from both branches are divided into three groups: Long-distance freshwater dependence (LD), medium-distance freshwater-dependent (MD), and short-distance freshwater dependence (SD), with the LD only appearing in the SB, while the NB is primarily represented by the MD. There is a correlation between the differences in Lf among different groups of C. nasus and the differences in the distance from the spawning grounds of C. nasus in different sections of the Yangtze River to the Estuary (DYRE), reflecting the distribution pattern of C. nasus spawning grounds in different sections of the Yangtze River. This study provides theoretical guidance for the protection of migration pathway and maintenance of spawning grounds for C. nasus, which has significant practical value in the precise management of C. nasus resources in the Yangtze River Estuary.

Hypophthalmichthys nobilis are widely distributed in the Yangtze River basin and its related lakes. They are an important economic fish species and are a famous cultured species known as the "Four Famous Domestic Fishes" in China. Currently, with the fishing ban in the Yangtze River basin, fishing for H. nobilis in natural water bodies of the Yangtze River basin has been completely prohibited. In order to identify the sources of H. nobilis appearing in the market, further control and accountability, it is necessary to trace the sources of H. nobilis in the Yangtze River basin and its related water bodies. Therefore, this study identified and traced different sources of H. nobilis through muscle element fingerprint analysis (EFA). The results show that H. nobilis from different stations have characteristic element compositions. The characteristic element of H. nobilis from Wuhan (WH) is Pb, which is significantly higher than that in other stations; the characteristic element from Anqing (AQ) is Hg, which is significantly higher than that in other stations; and the characteristic element from Taihu (TH) is Al, which is significantly higher than that in other water areas. Multivariate analysis selected different spatial distribution patterns of 4 discriminant elements ratios (Pb/Ca, Cr/Ca, Na/Ca, Al/Ca) in the muscle of H. nobilis in the Yangtze River basin and its related lakes. The study suggests that the screened discriminative elements can be used to visually distinguish different sources of H. nobilis, and to quickly trace and verify the origin of newly emerging samples. Therefore, the use of selected discriminant element fingerprint features to trace the origin of new samples has been proven to be feasible. By further discriminating and verifying the muscle element fingerprints of new samples, the discrimination rate is high. Therefore, Multivariate analysis for muscle element fingerprint can be used for origin traceability of samples of unknown origin in market supervision.

The genus Amomum encompasses six medicinal species that are extensively utilized and have a significant historical background. Due to their morphological similarities, however, the presence of counterfeit and substandard products remains a challenge. Accurate plant identification is therefore essential to address these issues. This study utilized 11 newly sequenced samples along with extensive data from NCBI to perform molecular identification of these six species. The plastomes of Amomum displayed a typical quadripartite structure with conserved gene content, yet showed independent variations in the SC/IR boundary shifts at both inter- and intra-specific levels. Our approach incorporated ITS, ITS1, ITS2, complete plastomes, matK, rbcL, and psbA-trnH sequences for molecular identification, which effectively differentiated the six medicinal species within the genus Amomum, as confirmed by distance-based and phylogenetic tree analyses. Among these, the ITS, ITS1, and complete plastomes sequences demonstrated the highest identification success rate (3/6), followed by ITS2, matK, and psbA-trnH (1/6). In contrast, rbcL failed to identify any species. This research successfully established a reliable molecular identification method for Amomum plants, to protect wild plant resources and promote the sustainable use of medicinal plants and restrict the exploitation of these resources.

Research Highlights: The correlations between the analyzed physical properties of seeds and seed mass were determined. The results were analyzed to determine most effective seed separation devices for the evaluated fir species. Background and Objectives: Information about the variations and correlations between the physical properties of seeds is essential for designing and modeling seed processing operations such as seed separation. The aim of this study was to determine the range of variations in the basic physical properties of seeds of selected fir species, and to identify the correlations between these attributes for the needs of the seed sorting processes. Materials and Methods: Terminal velocity, thickness, width, length, the angle of external friction and mass were determined in the seeds of 11 fir species. The measured parameters were used to calculate the geometric mean diameter, three aspect ratios, sphericity index and the specific mass of each seed. Results: The average values of the basic physical properties of the analyzed seeds were determined in the following range: terminal velocity – from 4.8 to 7.1 m s^-1, thickness – from 1.76 to 3.22 mm, width – from 3.29 to 5.57 mm, length – from 5.44 to 11.06 mm, angle of external friction – from 26 to 33°, and mass – from 7.9 to 48.3 mg. The seeds of Sierra white fir where most similar, whereas the seeds of balsam fir differed most considerably from the seeds of the remaining fir species. Conclusions: Fir seeds should be sorted primarily with the use of mesh sieves with longitudinal openings to obtain fractions with similar seed mass and to eliminate the need for dewinging.

Outdoor lighting is becoming increasingly widespread, and residents are suffering from serious light pollution as a result. Residents’ awareness of their rights to protection has gradually increased. However, due to the sometimes-inaccessible nature of residential vertical light incidence intensity data and the high cost of obtaining specific measurements, there is no appropriate hierarchic compensation for residents suffering from different degrees of light pollution. It is therefore important to measure light pollution levels and their damage at the neighborhood scale to provide residents with basic materials for proper protection and to create more politically suitable solutions. This article presents a light pollution assessment method that is easy to perform, is low-cost, and has a short data-processing cycle. This method can be used to monitor residential zone light pollution in other cities. We chose three open areas to test the spatial variation pattern of light intensity. The results are in accordance with spatial interpolation patterns and can be fit, with high precision, using the IDW method. This approach can also be used in 3 dimensions to quantitatively evaluate the distribution of light intensity distribution. We use a mixed-use zone in Beijing known as The Place as our case study area. The vertical illumination at the windows of residential buildings ranges from 2 lux to 23 lux; the illumination in some areas is far higher than the value recommended by CIE. Such severe light pollution can seriously interfere with people's daily lives and has a serious influence on their rest and health. The results of this survey will serve as an important database to assess whether the planning of night-time lighting is scientific and whether it provides residents with a basis for the protection of their rights.

Proteomics is the study of cellular proteome by investigating how different proteins interact with each other and the roles they play in the organism. For mRNA expression levels do not always correlate well with protein expression levels, and the study of mRNA does not consider protein posttranslational modifications (PTMs), complex formation and localization; all of which are key to protein function. Quantitative proteomics uses mass spectrometry to identify and quantify proteins so as to find differentially expressed proteins under different condition. This allows us to gain biological insights under stress or other pathological conditions. posttranslational modifications, such as lysine acetylation, succinylation and lactylation, occur after protein biosynthesis and play vital roles in protein activity and cell physiology regulation. Here we present the mass spectrometry analysis in detail to unveil protein acylase and deacylase’ roles in metabolic regulation based on PTMomics lysine acetylome and suincylome.

Immunohistochemistry (IHC) helps identify different types of tissues and provides important information about the pattern, shape, and structure of cells in a tissue sample. It is a very useful tool and widely used to uncover histology and pathology diagnosis uses. The IHC is a very useful tool to conduct research in the developmental biology area. Some insects, like butterflies, bees, beetles, ants, wasps, and moths, undergo a unique life cycle called complete metamorphosis, which has four distinct stages: egg, larva, pupa, and adult. Larvae are often wingless and have different habits and forms than adults, which are better suited for growth and development. During the metamorphosis, how does the insect legs change is a really an interesting issue.To better understand insect development, agriculture pest control, and insect pathogen interaction, here we use an insect Bombyx mori (domestic silk moth) as a model to detail how to conduct the IHC assays, such as HE staining, TUNEL to see the cell apoptosis, pH3 and BrdU staining to check cell division. The reagents can be easily found, and this step-by-step protocol is easily reproduced.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

Finishing coatings in the wood-based composites industry not only influence the final appearance of the product but also serve to protect against fungi, and molds, and reduce the release of harmful substances, particularly formaldehyde and volatile organic compounds (VOCs). Carbon-rich materials, such as those derived from birch bark extraction, specifically suberin acids, can fulfil this role. Previous research has demonstrated that adding suberin acid residues (SAR) at 20% and 50% by weight significantly enhances the gas barrier properties of surface finishing materials based on poly(lactide) (PLA) and polycaprolactone (PCL), particularly in terms of Total VOC (TVOC) and formaldehyde emissions. This study aims to explore whether these properties can be further improved through the incorporation of nano-zinc oxide (nano-ZnO). Previous research has shown that these nanoparticles possess strong resistance to biological factors and can positively affect the characteristics of nanofilms applied as surface protection. The study employed PLA and PCL finishing layers blended with SAR powder at 10% w/w and included 2% and 4% nano-zinc oxide nanoparticles. The resulting blends were milled to create a powder, which was subsequently pressed into 1 mm thick films. These films were then applied to raw particleboard surfaces. TVOC and formaldehyde emission tests were conducted. Additionally, the fungal resistance of the coated surfaces was assessed. The results showed that PLA/SAR and PCL/SAR composites with the addition of nano-zinc oxide nanoparticles exhibited significantly improved barrier properties, offering a promising avenue for developing biodegradable, formaldehyde-free coatings in the furniture industry with enhanced features. Furthermore, by utilizing SAR as a post-extraction residue, this project aligns perfectly with the concept of upcycling.

Some aporphine alkaloids, such as crebanine, were found to present arrhythmic activity and also higher toxicity. A series of derivatives were synthesized by using three kinds of aporphine alkaloids (crebanine, isocorydine, and stephanine) as lead compounds. Chemical methods, including ring-opening reaction, bromination, methylation, acetylation, quaternization, and dehydrogenation, were adopted. Nineteen target derivatives were evaluated for their antiarrhythmic potential in the mouse model of ventricular fibrillation (VF), induced by CHCl₃, and five of the derivatives were investigated further in the rat model of arrhythmia, induced by BaCl₂. Meanwhile, preliminary structure-activity/toxicity relationship analyses were carried out. Significantly, N-acetamidesecocrebanine (1d), three bromo-substituted products of crebanine (2a, 2b, 2c), N-methylcrebanine (2d), and dehydrostephanine (4a) displayedantiarrhythmic effects in the CHCl₃-induced model. Among them, 7.5 mg/kg of 2b was able to significantly reduce the incidence of VF induced by CHCl₃ (p<0.05), increase the number of rats that resumed sinus rhythm from arrhythmia, induced by BaCl₂ (p<0.01), and the number of rats that maintained sinus rhythm for more than 20 minutes (p<0.01). Therefore, 2b showed remarkably higher antiarrhythmic activity and a lower toxicity (LD₅₀=59.62 mg/kg, mice), simultaneously, indicating that 2b could be considered as a promising candidate in the treatment of arrhythmia. Structural-activity analysis suggested that variationsin antiarrhythmic efficacy and toxicity of aporphines were related to the C-1,C-2-methylenedioxy group on ring A, restricted ring B structural conformation, N-quaternization of ring B, levoduction of 6a in ring C, and the 8-, 9-, 10-methoxy groups on ring D on the skeleton.

Sterile alpha motif domain-containing protein 9 (SAMD9) is a regulatory protein centrally involved in cell proliferation and apoptosis. Mapped to 7p21.1, variants in SAMD9 have been reported in &lt;50 pediatric cases worldwide, typically with early lethality. Germline gain-of-function SAMD9 variants are associated with MIRAGE Syndrome (myelodysplasia, infection, restricted growth, adrenal hypoplasia, genital anomalies, and enteropathy). Spalt like transcription factor 1 (SALL1) is a zinc finger transcriptional repressor located at 16q12.1 where only two transcript variants in SALL1 are known. RUNX2 (6p21.1) encodes a nuclear protein with a Runt DNA-binding domain critical for osteoblastic differentiation, skeletal morphogenesis, and serves as a scaffold for nucleic acids and regulatory factors involved in skeletal gene expression. RUNX2 and SALL1 are thus both ‘master regulators’ of tissue organization and embryo development. Here, we describe exome sequencing and copy number variants in two previously unknown mutations—R824Q in SAMD9, and Q253H in SALL1. A new multiexon 3’ terminal duplication in RUNX2 is also reported. This is the first known phenotype characterization for the intersection of all three variants in a healthy 46,XX adult. Focusing on developmental progress, ultrastructural renal anatomy, and selected reproductive aspects, we describe this unique genotype diagnosed incidentally during Covid-19 illness. Individual disruption in SAMD9, RUNX2, or SALL1 would be expected to give a bleak prognosis. However, the convergence discovered here appears to dampen severe pathology, perhaps by cross-gene silencing of effects normally deleterious when such changes occur alone.

The first published description of intraovarian platelet-rich plasma (PRP) appeared in mid-2016, when a new experimental technique was successfully used in adult human ovaries to correct the reduced fertility potential accompanying advanced maternal age. Considering the potential therapeutic scope of intraovarian activated PRP and/or condensed platelet cytokines would likely cover both menopause treatment and infertility, the mainstream response has ranged from skeptical disbelief to welcome astonishment. Indeed, reports of restored menses in menopause (as an alternative to conventional hormone replacement therapy) and healthy term livebirths for infertility patients (either with IVF or as unassisted conceptions) after intraovarian PRP injection continue to draw notice. Yet any proper criticism of ovarian PRP applications will be difficult to rebut given the heterogenous patient screening, varied sample preparations, wide differences in platelet incubation and activation protocols, surgical/anesthesia techniques, and delivery methods. Notwithstanding these features, no adverse events have been reported thus far and ovarian PRP appears well tolerated by patients. Here, early research guiding the transition of ‘ovarian rejuvenation’ from experimental to clinical is outlined. Likely mechanisms are presented to explain results observed in both veterinary and human ovarian PRP research. Current and future challenges for intraovarian cytokine treatment are also discussed.

Laser range-gated underwater imaging technology, by removing most of the back scattering noise, can effectively increase the image contrast and extend the detection range. The optical signal captured by a range-gated imaging system primarily comprises reflected light from the object and backscattered light from the surrounding water. Consequently, surfaces with low reflectivity or highly turbid water environments substantially constrain the applicability of the range-gated imaging system. To enhance the detection capability of underwater laser range-gated imaging, this paper proposes the incorporation of underwater polarized light imaging technology as an enhancement method. Based on polarization differences, backscattered light and reflected light from an object can be distinguished. Experimental results indicate that, compared to images obtained using a conventional range-gated laser imaging system, those captured with a polarization-enhanced system exhibit an increase of up to 47%. The proposed approach, which integrates polarization imaging with range-gated laser imaging, has the potential to broaden the applicability of underwater laser imaging scenarios.

Supramolecular solvent (SUPRAS) has received increasing interest as an innovative, efficient, and green solvent for the effective extraction and separation of bioactive compounds from natural resources. However, studies on the use of SUPRAS for the extraction of phenolic components from plants, which are highly valued in food products due to their excellent antioxidant capacity, are still lacking. The present study developed a green ultrasound-assisted and efficient SU-PRAS method to simultaneously determine three phenolic acids in Prunella vulgaris by high-performance liquid chromatography (HPLC) and the experimental parameters were optimized in detail. The efficiency and antioxidant properties of the phenolic compounds obtained by different extraction methods were also compared. Under the optimal conditions, the extraction efficiency of SUPRAS, prepared with octanoic acid reverse micelles dispersed in ethanol-water, was substantially higher than conventional organic reagents. Moreover, this SUPRAS method also showed more significant antioxidant capacities. The confocal laser scanning microscopy (CLSM) images presented the spherical droplet structure of SUPRAS (A well-defined circle), which coincided with the position of the fluorescence position of phenolic acids. The phenolic acids were encapsulated in the vesicles by the SUPRAS droplets, which indicated the efficient extraction capacities of SUPRAS for the target compounds. Finally, combined with the CLSM method, the mechanism of the proposed method was further clarified, and the superior extraction performance of SUPRAS was theoretically demonstrated through molecular dynamics simulations. In comparison with conventional methods, the higher extraction efficiency of SUPRAS can be illustrated by the larger solvent contact surface area, more types of hydrogen bonds between extractants and supramolecular solvents, and stronger and more stable interaction forces. The results of the theoretical studies are in rational agreement with the experimental outcome.

The Rose grain aphid, a notable agricultural pest, releases saliva while feeding. Yet, there is a need for a comprehensive understanding of the specific identity and role of secretory proteins released during probing and feeding. Therefore, a combined transcriptomic and proteomic approach was employed to identify putative secretory proteins. The transcriptomic sequencing result led to the assembly of 18030 unigenes out of 31344 transcripts. Among these, 705 potential secretory proteins were predicted and functionally annotated against publicly accessible protein databases. Notably, a substantial proportion of secretory genes (71.5%, 69.08%, and 60.85%) were predicted to encode known proteins in Nr, Pfam, and Swiss-Prot databases, respectively. Conversely, 27.37% and 0.99% of gene transcripts were predicted to encode known proteins with unspecified functions in the Nr and Swiss-Prot databases, respectively. Meanwhile, the proteomic analysis result discovered, 30 salivary proteins. Interestingly, most salivary proteins (53.3% proteins) showed close similarity to A. craccivora, while 36.67% to A. pisum and A. glycines. However, to verify the expression of these secretory genes and characterize the biological function of salivary proteins further intervention should be geared towards gene expression and functional analysis.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

Wheat, a component of the staple diet globally, is a common food allergen in children. The symptoms of wheat allergy (WA) range from skin rash to shortness of breath, significantly impairing quality of life. Following initial clinical suspicion, individuals may undergo wheat allergen-specific skin prick test (SPT), blood test for serum immunoglobulin E (sIgE) levels or oral food challenge. Conventional management of WA lies in wheat avoidance, yet accidental consumption may be inevitable owing to the ubiquity of wheat in various food products. This article aims to provide an overview of the immunologic pathway of WA, followed by its novel diagnostic methods, namely alcohol-soluble SPT extracts, component-resolved diagnosis and basophil activation test (BAT). The mechanisms underlying wheat allergen-specific oral immunotherapy (OIT) as well as a summary of the efficacy, tolerability and safety of related clinical trials will then be discussed.

Chronic pancreatitis is a progressive fibroinflammatory disorder with no currently satisfactory treatment. Emerging evidence suggests an association between gut microbial dysbiosis and chronic pancreatitis. Although direct causative evidence is lacking, it is hypothesized that the gut microbiota may play a pivotal role in modulating pancreatic function via the gut-pancreas axis. Thus, modulating the gut microbiota through the administration of probiotics or prebiotics may alleviate pancreatic disorders. In this review, we first propose the potential mechanisms by which specific probiotics or prebiotics may ameliorate chronic pancreatitis, including the alleviation of small intestinal bacterial overgrowth (SIBO), facilitation of short-chain fatty acids (SCFAs) production, activation of the glucagon-like peptide 1 receptors (GLP-1Rs) in the pancreas. Since there are currently no probiotics or prebiotics used for the treatment of chronic pancreatitis, we have discussed research in other disease models that use probiotics or prebiotics to modulate pancreatic endocrine and exocrine functions and prevent pancreatic fibrosis. This provides indirect evidence for their potential application in the treatment of chronic pancreatitis. We anticipate that this research will stimulate further investigation into the gut-pancreas axis and the potential therapeutic value of probiotics and prebiotics in chronic pancreatitis.

Bigeye grunt Brachydeuterus auritus is an important economic species in the waters off Sierra Leone in West Africa, with great ecological value. Based on the survey data of bottom trawl nets from 6 voyages from 2019 to 2021, the body weight-length relationship (WLR), as well as their relative fatness, were studied in depth using the method of body length and its corresponding mean body weight. This study fitted the WLR of bigeye grunt by gender, calculated its fullness, and analyzed the influence of environmental factors. The results showed that month and gender had a significant impact on body length and weight distribution (P&lt;0.01). There was a highly significant negative correlation (P&lt;0.01) between the condition factor (a) and the allometric factor (b) in the WLR, and salinity significantly affects b (P&lt;0.05). The (lga)/b ratio was less affected by environmental factors which may be related to the body size and density of the fish. The difference in b between male and female populations was extremely significant (P&lt;0.01). The relative fatness had significant seasonal variation characteristics, with highly significant effects of sex and body length (P&lt;0.01). With increasing body length, the relative fatness showed two types of changes, continuously increasing and first increasing then decreasing, with salinity and b significantly affecting the type of change (P&lt;0.05) and depth having a highly significant effect (P&lt;0.01). The bigeye grunt off the coast Sierra Leone exhibited significant seasonal growth characteristics, with significant differences in growth characteristics between male and female individuals. This study suggested that salinity may be the main factor affecting its growth and development. In addition, this study hypothesised that the peak breeding season may occur during the dry season, beginning in December and ending before April of the following year. The study provides updated and more comprehensive insights into the biology and ecology of the bigeye grunt offshore Sierra Leone, West Africa, which can provide scientific basis for its resource assessment, development and utilization, and resource management.

Spodoptera frugiperda (J.E. Smith) is a global agricultural pest that poses a threat to crop production, characterized by its refractory polyphagous nature that makes it difficult to control and may lead to damage to woody plants. However, research on its adaptability to woody plants remains limited. This study compares the feeding adaptations (survival rate, pupation time, pupation rate, weight, length, and feeding volume), protective enzyme activities, and feeding preferences of S. frugiperda on leaves of six economically significant tree species (Areca catechu, Aquilaria sinensis, Cocos nucifera, Camellia oleifera, Dalbergia odorifera and Hevea brasiliensis) and maize as a control treatment. The results indicate that A. sinensis as the most vulnerable trees in high risk, H. brasiliensis and C. nucifera presented varying degrees of susceptibility, A. catechu, C. oleifera, and D. odorifera were unsuitability for S. frugiperda. In conclusion, this report extensively explores the feeding effects of S. frugiperda on six economically important tree species, and provides insights into the feeding preferences on these plants, thereby informing the potential threat posed by S. frugiperda to economically vital trees.

Involving local people in natural area management is very important to address the complexity of environmental management issues for sustainable use of local resources. Participatory methods require the contribution of local stakeholders in decision making. Mapping the environmental views of local communities allows for detecting aspects that could facilitate management efforts. This research – in the frame of the Skyros LIFE project and the PAMNATURA project - measures local acceptability of the conservation actions proposed by the LIFE project in Skyros Island (Greece) in relation with recording local people’s environmental orientation using the 15-item revised New Ecological Paradigm (NEP) scale. The research was carried out by means of questionnaires. The LIFE project proposed actions were grouped into three categories according to their theme, i.e. promoting (a) Nature protection, (b) Agro-pastoralism and (c) Ecotourism. The sample seems to largely agree with the LIFE project proposals, while the results showed high scores for most of the NEP scale items, implying pro-environmental beliefs, though there appears disagreement or neutrality regarding a few items. Local acceptability of the proposed actions was found to correlate to local people’s environmental concern measured through the NEP scale. Drawing on the results, implementation of actions related directly or indirectly to economic activities, preservation of traditional activities, as well as environmental education, interactive informing and consultation could enhance local participation. Skyros island seems to offer an appropriate social background for applying participatory and adaptive management and implementing conservation programs.

Synergistic control of emissions of air pollutants and CO2 is critical to the dual challenges of air quality improvement and climate change in China. Based on the emission inventories of thermal power units in Beijing, Tianjin, and Hebei, this study analyzes the CO2 and NOX emission characteristics of these units, identifies and quantifies the synergistic drivers affecting these emission trends. Inventory data show that between 2010 and 2020, NOX emissions were reduced by 86.1%, while CO2 emissions were reduced by only 29.8%. Although significant progress has been made in reducing NOX emissions through measures such as end-of-pipe treatment, controlling CO2 emissions remains a difficult task. The index decomposition analysis reveals that economic growth is the main driver of CO2 and NOx emission growth, energy intensity reduction is the main driver of CO2 emission reduction, and end-of-pipe treatment is the main driver of NOX emission reduction. Currently, coal occupies about 87% of the energy consumption of thermal power units in the Beijing-Tianjin-Hebei, and remains the main type of energy for synergistic emissions, and the potential for emission reduction in the energy structure remains huge. For NOX emissions, it is expected that 90% of the reduction potential can be achieved through energy restructuring and end-of-pipe treatment. In conclusion, the high-precision unit-by-unit emission study confirms the effectiveness of the control policy for thermal power units in the region and provides some scientific reference for future policy formulation.

Cyclocarya paliurus tea, also known as "sweet tea", a health substitute tea with Cyclocarya paliurus leaves as raw material, is famous for its unique nutritional benefits and flavor. However, due to the unique "bittersweet" of Cyclocarya paliurus tea, it is still unable to fully satisfy consumers' high-quality taste experience and oral pleasure. The taste and sensory quality of Cyclocarya paliurus tea are mainly determined by secondary metabolites. Therefore, this study aimed to explore the metabolites in Cyclocarya paliurus leaves during their growth process, particularly the composition and variation of sweet and bitter taste compounds, by combining multi-platform metabolomics analysis with an electronic tongue system and molecular docking simulation technology. The results indicated that there were significant differences in the contents of total phenols, flavonoids, polysaccharides and saponins of C. paliurus leaves in different growing months, among which the bioactive components in leaves harvested in July were the highest, and the best balance between sweetness and bitterness was achieved. A total of 575 secondary metabolites were identified as potential active metabolites related to sweet/bitter taste using nontargeted metabolomics based on UHPLC-MS/MS analysis. Molecular docking technology was utilized to study the interactions between candidate metabolites and the sweet receptor T1R2/T1R3 and the bitter receptor T2R4/T2R14. Six key compounds with high sweetness and low bitterness were successfully identified by using computational simulation analysis, including cis-Anethole, Gluconic acid, beta-D-Sedoheptulose, Asparagine, Proline, and Citrulline, which may serve as candidates for taste modification in Cyclocarya paliurus leaves. These findings provide a new perspective for understanding the sweet and bitter taste characteristics metabolites that contribute to the distinctive sensory quality of Cyclocarya paliurus leaves.

Since surface relief transmission gratings have very strict requirements on operators and use environment, according to the semiconductor laser external cavity spectral beam combining system, this paper proposes a design scheme of semiconductor laser array spectral beam combining system based on grating-external cavity. The finite element approach was used to create a wideband, high-efficiency fill-in multilayer dielectric transmission grating structure for a high-power spectrum beam combining system. The incidence angle, ridge height, duty cycle, and sidewall inclination angle of the transmission grating were tuned and evaluated, and a link between the transmission grating's diffraction efficiency and grating characteristics was discovered. The calculated design of the high-power fused silica transmission grating has a negative first-order peak diffraction efficiency of 99.5% in the 800nm range. In the spectral region of 765-872 nm, the transmission grating's diffraction effectiveness exceeds 92%. The filled ultra-high diffraction efficiency multilayer dielectric transmission grating design addresses the issue of resistance to high-power lasers under complicated operating settings, it’s intended to maintain a high diffraction efficiency even after several cleaning cycles, and it’s an ideal component for high-power spectrum beam combining systems.

This study evaluated batch fermentation modes, namely, separate hydrolysis and fermentation (SHF), Quasi-simultaneous saccharification and fermentation (Q-SSF), and simultaneous saccharification and fermentation (SSF), and fermentation conditions, i.e., enzyme and yeast loadings, nutrient supplementation and sterilization, on high titer bioethanol production from SPORL-pretreated Douglas-fir forest residue without detoxification. The result indicated Q-SSF and SSF were obviously superior to SHF operation in terms of ethanol yield. The enzyme loading showed a strong positive correlation between enzyme loading and the ethanol yield. The nutrient supplementation and sterility was not necessary for ethanol production from SPORL-pretreated Douglas-fir. The yeast loading showed no significant influence on the ethanol yield for typical SSF conditions. The terminal ethanol titer of 43.2 g/L, or 75.1% theoretical based on glucose, mannose, and xylose theoretical was achieved when SSF was conducted at the condition of following: whole slurry solids loading of 15%, enzyme loading of 20 FPU/g glucan, 1.8 g/kg (wet) yeast loading, without nutrition supplementation and sterilization, at 38°C, on shake flask at 150 rpm for 96h. It is believed that with mechanical mixing, enzyme loading can be substantially reduced with affect ethanol yield by using a long fermentation time.