A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Often, engineers with machining experience often judge machining state and tool life according to chips’ features. Engineers' experience is digitized in this study. During the cutting process, the cutting tool coming in contact with the workpiece produces a shear zone, which causes plastic deformation and shear slip. The chips closest to the shear zone can directly show the state of the tool and workpiece when the material is SKD61. This study used chip color, vibration, and current signal integration for prediction of machining state and cutting tool life. When the cutting tool wears increased, the chip surface color changed in the following way: purpleè purple blueè blue ècyan, or even green and yellow. When the cutting tool was in the accelerating wear phase, the color change was particularly obvious. The Back-Propagation Levenberg–Marquardt (BP-LM) predictive methodology was used to compare the predictive ability of voltage, vibration signal, and chip color. The Mean Absolute Percentage Error (MAPE) for the voltage signal was 12.28%, for the vibration signal it was 11.38%, and for the chip color combined with multi-sensor characteristics it was 7.85%. The MAPE of the chip color was the smallest. Using the General Regression Neural Network (GRNN) methodology, the MAPE for the voltage signal was 10.74%, for the vibration signal 7.96%, and for the chip color combined with multi-sensor characteristics was 6.59%. The MAPE of the chip color was the smallest. Obviously, the chip color combined with multi-sensor signals provided better predictive results than the vibration signal or voltage signal alone. There is currently no research on the usefulness of monitoring chip color for tool life prediction.

The reasons for the circular sense of human color perception generated by two sorts of color opponent neurons and three cone types are not well understood. Here we use geometrical analysis to examine the hypothesis that opponency, the recursive nature of color perception, and trichromacy arise as the most efficient ways of distinguishing spectrally different points on a plane using a minimum of color classes and receptor types.

We propose a novel unsupervised semantic segmentation method for fast and accurate flood area detection utilizing color images acquired from Unmanned Aerial Vehicles (UAVs). To the best of our knowledge, this is the first fully unsupervised method for flood area segmentation in color images captured by UAVs, without the need of pre-disaster images. The proposed framework addresses the problem of flood segmentation based on parameter-free calculated masks and unsupervised image analysis techniques. First, a fully unsupervised algorithm gradually excludes areas classified as non-flood utilizing calculated masks over each component of the LAB colorspace, as well an RGB vegetation index and the detected edges of the original image. Unsupervised image analysis techniques, such as distance transform, are then applied, producing a probability map for the location of flooded areas. Finally, flood detection is obtained by applying the hysteresis thresholding segmentation. The proposed method is tested and compared with variations, and other supervised methods in two public datasets, consisting of 953 color images in total, yielding high-performance results, with 87.4% and 80.9% overall accuracy and F1-Score, respectively. The results and computational efficiency of the proposed method show that it is suitable for on board data execution and decision-making during UAVs flight.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

The tumor microenvironment is known to have increased levels of cytokines and metabolites, such as glutamate, due to their release from the surrounding cells. A normal cell around the tumor that responds to the inflammatory environment is likely to be subsequently altered. We will discuss how these abnormalities will support tumor survival via the actions of gap junctions (GJs) and hemichannels (HCs) which are composed of hexamer of connexin 43 (Cx43) protein. In particular, we will discuss how GJ intercellular communication (GJIC) in glioma cells, the primary brain tumor, is a regulatory factor and its attenuation leads to tumor invasion. In contrast, the astrocytes, which are normal cells around the glioma, are "hijacked" by tumor cells, either by receiving the transmission of malignant substances from the cancer cells via GJIC, or perhaps via astrocytic HC activity through the paracrine signaling which enable the delivery of these substances to the distal astrocytes. This astrocytic signaling would promote tumor expansion in the brain. In addition, brain metastasis from peripheral tissues has also been known to be facilitated by GJs formed between cerebral vascular endothelial cells and cancer cells. Astrocytes and microglia are generally thought to eliminate cancer cells at the blood brain barrier. In contrast, some reports suggest they facilitate tumor progression as tumor cells take advantage of the normal functions of astrocytes that support the survival of the neurons by exchanging nutrients and metabolites. In summary, GJIC is essential for the normal physiological function of growth and allowing the diffusion of physiological substances. Therefore, whether GJIC is cancer promoting or suppressing may be dependent by what permeates through GJs, when it is active, and to which cells. The nature of GJs, which has been ambiguous in brain tumor progression, will need to be re-visited and understood together with new findings on Cx proteins and HC activities.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

There is a restricted knowledge about the potential impact of the use of different wood species on color and anthocyanin changes during the red wine aging process. This lack of knowledge is even greater when no oak wood species are used. Thus, the aim of this study was to carry out a comparative analysis of the impact of wood chip extracts from oak, acacia and cherry species on the chromatic characteristics and anthocyanins changes by the use of model wine solutions. In this context, several methodologies were used to quantified, color and anthocyanins changes during the aging time studied. The results indicated that the contact between wood chip extracts and grape skin isolated anthocyanin extracts induced a decrease of color intensity, particularly red color, and also the anthocyanin content in the different experimental model wine solutions studied. All chromatic modifications are potentially detected by human eyes because ΔE values were much higher than 3 CIELab units. These tendencies seems to be independent of the wood species used, but more pronounced for higher contact time between wood chip extracts and anthocyanins. The obtained results may contribute to a better understanding of the chromatic changes of red wines when aged in contact with different wood chips species.

Gene regulation is vital for cellular function and homeostasis, involving diverse mechanisms controlling specific gene products and contributing to tissue-specific gene expression. Dysregulation leads to diseases, emphasizing the need for understanding these mechanisms. Non-coding regions, notably enhancers and super-enhancers (SEs), act as crucial gene regulators, orchestrating transcriptional activity via transcription factors (TFs). SEs, with high activity, are pivotal in cell identity and disease progression. Current computational approaches focus on individual regulators like TFs and miRNAs, neglecting SE interactions. We emphasize incorporating SEs into models to enhance understanding. Experimental studies have recently linked miRNAs and TFs to SEs. Chromatin immunoprecipitation followed by sequencing (ChIP-Seq) provides valuable SE information. In this review, we categorize computational methods leveraging TF and miRNA data into three areas and explore challenges integrating enhancers/SEs. These include unraveling indirect regulatory networks, identifying network motifs, and enriching pathway identification by dissecting gene regulators, including SEs. We hypothesize that addressing these challenges will enhance our understanding of gene regulation, aiding in identifying therapeutic targets and disease biomarkers. We believe that understanding the role of ChIP-Seq data in predicting the effect of miRNA on gene regulation is crucial to construct statistical/computational model that would tackle these challenges.

Organ-on-Chip is a game-changing technology born from the convergence of tissue engineering and microfluidic technology. Organ-on-Chip devices (OoCs) are expected to offer effective solutions to persisting problems in drug development and personalized disease treatments. This opinion paper surveys the current landscape in research, development, application and market opportunities for OoCs to help establishing a global and multi-stakeholder OoC ecosystem. Based on a bibliometric study, a market analysis, expert interviews, and panel discussions held at the ORCHID Vision Workshop (Stuttgart, 23 May 2018), we outline presently unmet needs, key challenges, barriers and perspectives of the field, and finally propose recommendations towards the definition of a comprehensive roadmap that could render OoCs realistic models of human (patho)physiology in the near future.

The study of the impact of polyQ expansion driven proteotoxicity on cell metabolism has evi-denced NAD molecule as a central player in regulating metabolic response and cell repair in neurodegeneration. The decline in NAD intracellular levels represents a hallmark of ageing aris-ing from a dysregulation between NAD-consuming and biosynthetic enzymatic reactions in which NMNAT plays a key role. By an integrated bioanalytical and proteomic experimental design, the derangement of NAD metabolism deriving from the accumulation of polyQ-Htt protein has been analysed in Saccha-romices cerevisiae harbouring a 103Q-Htt and compared with wild-type Htt, in absence and in presence of a phenolic extract from EVOO, as a source of antioxidant bioactive compounds. Quantification of NAD and its precursors and proteomic analysis of the differential protein ex-pression has been performed by LC-DAD-MS. Chronological lifespan and NAD homeostasis was strongly impaired by proteotoxic polyQ-Htt, eliciting a depletion of NAD levels and accumulation of NaMN. In parallel a downregulation of Sirt2 expression levels has been observed. Phenolic extract administration had no meaningful ef-fects on NAD replenishment to prevent proteotoxicity. NaMN can represent a biomarker of accel-erated aging, and/or a signaling molecule for cell repair.

This paper presents a theory on graph topological structure and graph coloring, proving that for any N-order graph structure (with a topological structure similar to ), the maximum number of colors required for coloring is less than or equal to . The Four Color Theorem is just one special case of this theory, with the maximum structure size for a four-color graph being a 4-order structure graph, hence requiring only a maximum of 4 colors for coloring.

Monarch butterflies are a species of conservation priority due to declining overwintering populations in both eastern and western North America. Declines in western overwintering monarchs—more than 99% since monitoring began—are especially acute. However, the degree to which the western monarch is a distinct biological entity is uncertain. In this review, we focus on phenotypic and genetic differentiation between eastern and western monarchs, with the goal of informing researchers and policy-makers who are interested in monarch conservation. Eastern and western monarchs occupy distinct environments and show some evidence for phenotypic differentiation—particularly for migration-associated traits—though population genetic and genomic studies suggest that they are genetically indistinguishable from one another. We suggest future studies that could improve our understanding of differences between eastern and western monarchs. We also discuss the concept of adaptive capacity in eastern and western monarchs as well as non-migratory populations outside of the monarch’s primary North American range.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

This paper presents computer and color vision research focusing on human color perception in VR environments. A VR art gallery with digital twins of original artworks is created for this experiment. In this research, the field of colorimetry and the application of CMYK and RGB color models are applied. The interrelationships of the two colors models are applied to create a color modification of the VR art gallery environment using C# Script procedures. This color-edited VR environment works with a smooth change of color tone in a given time interval. At the same time, a sudden change in the color of the RGB environment is defined in this interval. This experiment aims to record a user's reaction embedded in a VR environment and the effect of color changes on human perception in a VR environment. The research uses lie detector sensors that record the physiological changes of the user embedded in VR. Five sensors are used to record the signal. An experiment on the influence of the user's color perception in a VR environment using lie detector sensors has never been conducted. This research defines the basic methodology for analyzing and evaluating the recorded signals from the lie detector. The presented text thus provides a basis for further research in the field of colors and human color vision in a VR environment and lays an objective basis for use in many scientific and commercial areas.

This paper presents an Edge-based color image segmentation derived from the method of Particle Motion in a Vector Image Fields (PMVIF) that could previously be applied only to monochrome images. Instead of using an edge vector field derived from a gradient vector field and a normal compressive vector field derived from a Laplacian-gradient vector field, two novel orthogonal vector fields, directly computed from a color image, one parallel and another orthogonal to the edges, were used in the model to force a particle to move along the object edges. The normal compressive vector field is derived from the center-to-centroid vectors of local color distance images. Next, the edge vector field is derived by taking the normal compressive vector field, multiplied by differences of auxiliary image pixels to obtain a vector field analogous to a Hamiltonian gradient vector field. Using the PASCAL Visual Object Classes Challenge 2012 (VOC2012) and the Berkeley Segmentation Data Set and Benchmarks 500 (BSDS500), the benchmark score of the proposed method is provided in comparison with those of the traditional PMVIF, Watershed, SLIC, K-means, Mean shift, and JSEG. The proposed method yields better RI, GCE, NVI, BDE, Dice coefficients, faster computation time, and noise resistance.

The gut plays a key role in drug absorption and metabolism of orally ingested drugs. Additionally, characterization of intestinal disease processes are increasingly gaining more attention as gut health is an important contributor to our overall health. The most recent innovation to study intestinal processes in vitro is the development of gut-on-a-chip (GOC) systems. Compared to conventional in vitro models they offer more translational value, and many different GOC models have been presented over the past years. Here, we reflect on the almost unlimited choices in designing and selecting a GOC for preclinical drug (or food) development research. Four components that largely influence the GOC design are highlighted, namely 1) the biological research questions, 2) chip fabrication and materials, 3) tissue engineering, and 4) the environmental and biochemical cues to add or measure in the GOC. Examples are presented of GOC studies in the two major areas of preclinical intestinal research: 1) intestinal absorption and metabolism to study the oral bioavailability of compounds, and 2) treatment-orientated research for intestinal diseases. The last section of this review presents an outlook on the limitations to overcome in order to accelerate preclinical GOC research.

Gravity played an important role in the development of life on earth. The effect of gravity on a living organisms can be investigated by controlling the magnitude of gravity. Most reduced gravity experiments are conducted on the lower earth orbit (LEO) in the International Space Station (ISS). However, running experiments in ISS face challenges such as high cost, extreme condition, lack of direct accessibility, and long waiting period. Therefore, researchers have developed various ground-based devices and methods to perform reduced gravity experiments. However, the search for life outside the earth requires more intensive research. Advancements in conventional methods and the development of new tools are required for this purpose. The advantages of Lab-on-a-Chip (LOC) devices make them an attractive option for simulating microgravity. This paper briefly reviews the advancement of LOC technologies for simulating microgravity in a earth-based laboratory.

Organ-on-a-Chip (OoC) systems bring together cell biology, engineering, and material science for creating systems that recapitulate the in vivo microenvironment of tissues and organs. The versatility of OoC systems enables in vitro models for studying physiological processes, drug development, and testing in both academia and industry. This paper evaluates current platforms from the end-user perspective, elaborating on usability, complexity, and robustness. We surveyed 165 peers in over 30 countries and grouped the responses according to preliminary knowledge and the source of the OoC systems that are used. The survey clearly shows that current commercial OoC platforms provide a substantial level of robustness and usability - which is also indicated by an increasing adaptation of the pharmaceutical industry but a lack of complexity can challenge their use as a predictive platform. Self-made systems on the other hand are less robust and standardized but provide the opportunity to develop customized and more complex models which are often needed for human disease modeling. This review serves as a guide for researchers in the OoC field and encourages the development of next-generation OoCs.

This study aimed to evaluate the discrepancies between genetic and visual coat color assignment in the Sarcidano Horse and to elucidate potential reasons. Individual DNA from 90 Sarcidano Horses was used for genetic assignment of coat color to explore the correspondence with individual forms containing phenotypical traits. The MC1R exon 1 and ASIP exon 3 have been genotyped and sequenced to obtain a picture of the coat color distribution in this breed. Surprisingly, once we compared the genetic results with the individual forms reporting the phenotypic data for each subject, a certain degree of non-correspondence between the phenotypic and genetic data in relation to coat color emerged. From the genetic analysis, Chestnuts (n = 58) resulted the most common Sarcidano Horse (n = 58), followed by a quite large number of Blacks (n = 28) and a very small number of Bays (n = 4), whereas phenotypic distribution resulted in 38 Chestnuts, 40 Bays, only 2 Blacks, and 10 Grays (without the possibility of recognizing the true color they carried). Chestnut resulted a very representative coat color, while many horses that visually identified as Bays were genetically Blacks. This discrepancy, that could be due to a variety of individual and external factors, including age, time of year, living situation and dietary condition, suggesting the importance of accurate coat color identification to ensure adequate features registration and reliable prediction of offspring’s coat color.

Color plays an important part in human activities, affects circadian cycle and decision making process. Therefore, it is important to investigate human judgment under different color of illumination, especially, because color perception is subjective. In this study, we developed required instrumentation to control the red (R), green (G), Blue (B) and Amber (A) colored light emitting diode (LED) lamp for carrying out Magneto Encephalography (MEG) brain scan. We developed a software to generate all the colors in the visual spectrum, predefined white light combinations and saturation of an illuminated objects by using RGBA color pallet. The lamp is required to control from outside of the MEG electromagnetically shielded room with the LED lamp located inside the MEG room. Hence, USB is used for the communication mode. The feasibility of using LED lamp with MEG brain scanner has been validated for bio-medical and psychological MEG experiments.

Vertebrate color vision is evolutionarily ancient. Jawless fish evolved four main spectral types of cone photoreceptor, almost certainly complemented by retinal circuits to process chromatic opponent signals. Subsequent evolution of photoreceptors and visual pigments are now documented for many vertebrate lineages and species, giving insight into evolutionary variation and ecological adaptation of color vision. We look at organization of the photoreceptor mosaic and the functions different types of cone in teleost fish, primates, and birds and reptiles. By comparison less is known about the underlying neural processing. Here we outline the diversity of vertebrate color vision and summarize our understanding of how spectral information picked up by animal photoreceptor arrays is adapted to natural signals. We then turn to the question of how spectral information is processed in the retina. Here, the quite well known and comparatively ‘simple’ system of mammals such as mice and primates reveals some evolutionarily conserved features such as the mammalian Blue^ON system which compares short and long wavelength receptors signals. We then survey our current understanding of the more complex circuits of fish, amphibians, birds and reptiles. Together, these clades make up more than 90% of vertebrate species, yet we know disturbingly little about their neural circuits for colour vision beyond the photoreceptors. Here, long-standing work on goldfish, freshwater turtles and other species is being complemented by new insights gained from the experimentally amendable retina of zebrafish. From this body of work, one thing is clear: The retinal basis of colour vision in non-mammalian vertebrates is substantially richer compared to mammals: Diverse and complex spectral tunings are established at the level of the cone output via horizontal cell feedforward circuits. From here, zebrafish use cone-selective wiring in bipolar cells to set-up color opponent synaptic layers in the inner retina, which in turn lead a large diversity of color-opponent channels for transmission to the brain. However, while we are starting to build an understanding of the richness of spectral properties in some of these species’ retinal neurons, little is known about inner retinal connectivity and cell-type identify. To gain an understanding of their actual circuits, and thus to build a more generalised understanding of the vertebrate retinal basis of color vision, it will be paramount to expand ongoing efforts in deciphering the retinal circuits of non-mammalian models.

Cutaneous wound healing is a complex multi-stage process involving direct and indirect cell communication events with the aim of efficiently restoring the barrier function of the skin. One key aspect in cutaneous wound healing is associated with cell movement and migration into the physically, chemically and biologically injured area resulting in wound closure. Understanding the conditions under which cell migration is impaired and elucidating the cellular and molecular mechanisms that improve healing dynamics is therefore crucial in devising novel therapeutic strategies to elevate patient suffering, reduce scaring and eliminate chronic wounds. Following the global trend towards automation, miniaturization and integration of cell-based assays into microphysiological systems, conventional wound healing assays such as the scratch assay or cell exclusion assay have recently been translated and improved using microfluidics and lab-on-a-chip technologies. These miniaturized cell analysis systems allow precise spatial and temporal control over a range of dynamic microenvironmental factors including shear stress, biochemical and oxygen gradients to create more reliable in vitro models that resemble the in vivo microenvironment of a wound more closely on a molecular, cellular, and tissue level. The current review provides (a) an overview on the main molecular and cellular processes that take place during wound healing, (b) a brief introduction into conventional in vitro wound healing assays, and (c) a perspective on future cutaneous and vascular wound healing research using microfluidic technology.

Introduction Color vision deficiency (CVD) constitutes one of the frequently observed eye disorders in all human populations. Color is a prominent sign utilized in the medical profession to study and identify histopathological specimens, lab instruments, and patient examination. Color deficiency affects the medical skills of students resulting in poor clinical examination and color appreciation. There is no effective screening of CVD at any level of the medical profession. Hence, this study was aimed to determine the prevalence of CVD among medical students. Materials and methods This was a cross-sectional study conducted from September 2019 to February 2020 over a period of six months in Karachi, Pakistan. All medical students aged 18-21 years of either gender enrolled in the first and second years of medical college were included in this study. The examination was performed during daylight. Ishihara plates were placed at a distance of 75 cm from the subject and tilted so that the plane of the paper lies perpendicular to the line of vision. Students were given five seconds to read the plate and one examiner was instructed to mark the checklist. A score of less than 12 out of 14 red/green test plates (not including the demonstration plate) was considered as a CVD. All statistical analysis was performed using Statistical Package for Social Sciences version 20.0 (Armonk, NY: IBM Corp). Results The mean age of the medical students was 19.61± 1.22 years. There were (n=123) 53.0% females and (n=111) 47.0% males. Most of the medical students (n=131, 56.0%) belonged to the upper-middle-class socioeconomic group. CVD was observed in (n=13) 6.0%of medical students. Age (p=0.001) and socioeconomic status (p=0.001) were the only demographic factors significantly associated with color deficiency. Conclusions Color deficiency, although an unnoticed concern, is fairly common among medical students. Medical students must be screened for CVD as this will enable them to be aware of their limitations in their future observational skills as a doctor and devise ways of overcoming them in clinical practice.

Identifying the total number of fruits on trees has long been of interest in agricultural crop estimation work. Yield prediction of fruits in practical environment is one of the hard and significant tasks to obtain better results in crop management system to achieve more productivity with regard to moderate cost. Utilized color vision in machine vision system to identify citrus fruits, and estimated yield information of the citrus grove in-real time. Fruit recognition algorithms based on color features to estimate the number of fruit. In the current research work, some low complexity and efficient image analysis approach was proposed to count yield fruits image in the natural scene. Semi automatic segmentation and yield calculation of fruit based on shape analysis is presented. Color and shape analysis was utilized to segment the images of different fruits like apple, pomegranate obtained under different lighting conditions. First the input sectional tree image was converted from RGB colour space into the colour space transform (i.e., YUV, YIQ, or YCbCr). The resultant image was then applied to the algorithm for fruit segmentation. After it is applied Morphological Operations which is enhanced image then execute Blob counting method which identify the object and count the number of it. Accuracy of this algorithm used in this thesis is 82.21% for images that have been scanned.

Over the last two decades, microfluidics has received significant attention from both academia and industry, and researchers report thousands of new prototype devices each year for use in a broad range of environmental, pharmaceutical, and biomedical engineering applications. While lab-on-a-chip fabrication costs have continued to decrease, the hardware required for monitoring fluid flows within microfluidic devices themselves remains expensive and often cost prohibitive for researchers interested in starting a microfluidics project. As microfluidic devices become capable of handling complex fluidic systems, low-cost, precise and real time pressure and flow rate measurement capabilities has become increasingly important. While many labs use commercial platforms and sensor, these solutions can often cost thousands of dollars and can be too bulky for on-chip use. Here we present a new inexpensive and easy -to-use piezoresistive pressure and flow sensor that can be easily integrated into existing on-chip microfluidic channels. The sensor consists of PDMS-Carbon black conductive membranes and uses an impedance analyzer to measure impedance change due fluid pressure. The sensor costs several orders of magnitude less than existing commercial platforms and can monitor local fluid pressures and calculate flow rates based on pressure gradient.

The role of circulating plasma cells (CPCs) and circulating leukemic cells (CLCs) as biomarkers for several blood cancers, such as multiple myeloma and leukemia, respectively, have recently been reported. These markers can be attractive due to the minimally invasive nature of their acquisition through a blood draw (i.e., liquid biopsy) negating the need for painful bone marrow biopsies. CPCs or CLCs can be used for cellular/molecular analyses, such as immunophenotyping or fluorescence in situ hybridization (FISH). FISH, which is typically carried out on slides involving complex workflows, becomes problematic when operating on CLCs or CPCs due to their relatively modest numbers. Here, we present a microfluidic device for characterizing CPCs and CLCs enriched from peripheral blood using immunofluorescence or FISH. The microfluidic possessed an array of cross-channels (2-4 µm in depth and width) that interconnected a series of input and output fluidic channels. Placing a cover plate over the device formed microtraps, the size of which was defined by the width and depth of the cross-channels. This microfluidic chip allowed for automating immunofluorescence and FISH requiring the use of small volumes of reagents, such as antibodies and probes, as compared to slide-based immunophenotyping and FISH. In addition, the device could secure FISH results in <4 h compared to 2-3 d for conventional FISH.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

For applications in sensing and cavity-based quantum computing and metrology, open-access Fabry-Perot cavities – with an air or vacuum gap between a pair of high reflectance mirrors – offer important advantages compared to other types of microcavities. For example, they are inherently tunable using MEMS-based actuation strategies, and they enable atomic emitters or target analytes to be located at high field regions of the optical mode. Integration of curved-mirror Fabry-Perot cavities on chips containing electronic, optoelectronic, and optomechanical elements is a topic of emerging importance. Micro-fabrication techniques can be used to create mirrors with small radius-of-curvature, which is a prerequisite for cavities to support stable, small-volume modes. We review recent progress towards chip-based implementation of such cavities, and highlight their potential to address applications in sensing and cavity quantum electrodynamics.

This work presents an analytical methodology to predict meat juiciness (discriminant semi-quantitative analysis using groups of intervals of intramuscular fat) and intramuscular fat (regression analysis) in Longissimus thoracis et lumborum (LTL) muscle of Bísaro pigs using as independent variables the animal carcass weight and parameters from color and image analysis. These are non-invasive and non-destructive techniques which allow development of rapid, easy and inexpensive methodologies to evaluate pork meat quality in a slaughterhouse. The proposed predictive supervised multivariate models were non-linear. Discriminant mixture analysis to evaluate meat juiciness by classified samples into three groups—0.6 to 1.1%; 1.25 to 1.5%; and, greater than 1.5%. The obtained model allowed 100% of correct classifications (92% in cross-validation with seven-folds with five repetitions). Polynomial support vector machine regression to determine the intramuscular fat presented R2 and RMSE values of 0.88 and 0.12, respectively in cross-validation with seven-folds with five repetitions. This quantitative model (model’s polynomial kernel optimized to degree of three with a scale factor of 0.1 and a cost value of one) presented R2 and RSE values of 0.999 and 0.04, respectively. The overall predictive results demonstrated the relevance of photographic image and color measurements of the muscle to evaluate the intramuscular fat, rarther than the usual time-consuming and expensive chemical analysis.

This document introduces a new cryptosystem mixing two improvement standards generally used for text encryption, in order to give birth a new color image encryption algorithm capable of dealing with known attacks. Firstly, two substitution matrixes attached to a strong replacement function will be generated for advanced Vigenere technique application. At the end of this first round, the output vector is subdivided into size blocks according to the used chaotic map, for acting a single enhanced Hill circuit insured by a large inversible matrix. A detailed description of such a large involutive matrix constructed using Kronecker products will be given. accompanied by a dynamic translation vector to eliminate any linearity. A solid chaining is established between the encrypted block and the next clear block to avoid any differential attack. Simulations carried out on a large volume of images of different sizes and formats ensure that our approach is not exposed to any known attacks.

In this paper, we found new classes of exact models to the Einstein-Maxwell system of equations which describe the internal structure of a compact star made of strange matter considering the equation of state proposed by Rocha, Bernardo, de Avellar and Horvath in 2019. It has been assumed that this matter is composed of equal number of up, down and strange quarks and a small amount of electrons required to reaching the charge neutrality. If this hypothesis is correct, the neutron stars could be strange stars or hybrid stars with a thin crust of nuclei where the temperatures and pressures are capable of converting hadronic matter into this new stable phase of quarks. We have chosen a particular form of gravitational potential Z(x) that depends on an adjustable parameter related to degree of anisotropy of the models and the new solutions can be written in terms of elementary and polynomial functions. The obtained models satisfy all physical features expected in a realistic star and the expressions for mass, density and stellar radius are comparable with the experimental results.

Domain-specific systems-on-chip (DSSoCs) aim to narrow the gap between general-purpose processors and application-specific designs. CPU clusters enable programmability, while hardware accelerators tailored to the target domain minimize task execution times and power consumption. Traditional operating system (OS) schedulers can diminish the potential of DSSoCs as their execution times can be orders of magnitude larger than the task execution time. To address this problem, we propose a dynamic adaptive scheduling (DAS) framework that combines the advantages of a fast, low-overhead scheduler and a sophisticated, high-performance scheduler with a larger overhead. We present a novel runtime classifier that chooses the better scheduler type as a function of the system workload, leading to improved system performance and energy-delay product (EDP). Experiments with five real-world streaming applications indicate that DAS consistently outperforms fast, low-overhead, and slow, sophisticated schedulers. DAS achieves a 1.29x speedup and 45% lower EDP than the sophisticated scheduler under low data rates and a 1.28x speedup and 37% lower EDP than the fast scheduler when the workload complexity increases. Furthermore, we demonstrate that the superior performance of the DAS framework also applies to hardware platforms, with up to a 48% and 52% reduction in execution time and EDP, respectively.

In many image processing and computer vision applications, the main aim is to describe image contents. So, different visual properties such as color, texture and shape are extracted to make aim. In this respect, texture information play important role in image description and visual pattern classification. Texture is referred to a specific local distribution of intensities that is repeated throughout the image. Since now different operations or descriptors have been proposed to analysis texture characteristics. In the multi object images specific texture operators usually doesn’t provide accurate results. So, in many cases, combination of texture operators are used to achieve more discriminant features. In this paper, some combination methods are survived to analysis effect of combinational texture features in image content description. Also, in the result part, different related methods are compared in terms of accuracy and computational complexity.

Oriented strand board (OSB) panels are widely marketed for several applications, from building to packaging. The manufacturing of poplar OSB started recently in Northern Italy representing a relevant innovation in the sector since this product is usually made of coniferous wood. The thermal treatment is widely used for reducing the hygroscopicity of wood-based products, nonetheless it influences the mechanical behavior and degrades the main components of wood, which can affect their finishing. Therefore, it is important to know the properties of the treated surfaces. To this purpose, in this study a lot of OSB panels, made of poplar wood, 15 mm thick and with a density of 590 kg/m³, were thermally treated under vacuum conditions at 190 °C for 2 h and then subjected to accelerated weathering. The changes in color and in wettability due to treatment and accelerated weathering were studied. The thermal treatment determined a significant darkening of the color; the accelerated weathering darkened the untreated surfaces and, on the opposite, lightened the thermo-treated surfaces. The wettability decreased after thermal treatment and increased after weathering, more evidently in treated panels. Overall, this study improves the knowledge about the behavior of the surface of thermo-treated poplar OSB, which is relevant for the industrial coating of this product.

Herein, we offer a numerical study on the devising of a unique 2D-heterostructure Photonic crystal (PC) that can split two orthogonally polarized light waves. The analysis is performed via a two-dimensional finite element method (2D-FEM) by utilizing COMSOL Multiphysics software. The device consists of two discrete designs of PC formation. The first PC formation is optimized so that it permits both TE and TM-polarization of light to transmit through it. Whereas the second PC formation possesses a Photonic Bandgap (PBG) only for TE-polarized light. These two formations are combined at an angle of 45 degrees, resulting in a reflection of self-collimated TE-polarized light at an angle of 90 degrees owing to the PBG present in the second PC formation. While permitting the self-collimated TM-polarized light wave to travel uninterrupted. The proposed device has a small footprint of ~10.5 μm2 offering low transmission loss and high polarization extinction ratio which makes it an ideal candidate to be employed as an on-chip polarization division multiplexing system.

Optofluidics, a research discipline combining optics with microfluidics, currently aspires to revolutionize the analysis of biological and chemical samples e.g. for medicine, pharmacology, or molecular biology. In order to detect low concentrations of analytes in water, we developed an optofluidic device containing a nanostructured substrate for surface enhanced Raman spectroscopy (SERS). The geometry of the gold surface allows localized plasmon oscillations to give rise to the SERS effect, in which the Raman spectral lines are intensified by the interaction of the plasmonic field with the electrons in the molecular bonds. The SERS substrate was enclosed in a microfluidic system, which allowed transport and precise mixing of the analyzed fluids, while preventing contamination or abrasion of the highly sensitive substrate. To illustrate its practical use, we employed the device for quantitative detection of persistent environmental pollutant 1,2,3-trichloropropane in water in submillimolar concentrations. The developed sensor allows fast and simple quantification of halogenated compounds and it will contribute towards the environmental monitoring and enzymology experiments with engineered haloalkane dehalogenase enzymes.

The need for miniaturized shear force sensors is expanding, particularly for biomedical applications. Examples include measuring interfacial shear stresses between a human and an external device (e.g., footwear or a prosthesis). However, there are considerable challenges in designing a shear sensor for these applications due to the need for a small package, low power requirements, and resistance to interference from motion artifact and electromagnetic fields. This paper presents the design, fabrication, and characterization sensor that measures two-axis shear force by detecting displacement between a color panel and a red, green, and blue light-sensing photodiode. The sensor response to applied displacements and forces was characterized under benchtop testing conditions. We also present the design of a prototype wireless version of the sensor for integration into footwear. The sensor exhibited strong agreement with gold standard measurements for two axis shear displacements (R2>0.99, RMSE≤5.0 µm) and forces (R2>0.99, RMSE≤0.94 N). This performance, along with the sensor’s scalability, miniaturized form, and low power requirements make it well-suited a variety of biomedical applications.

Synesthesia is a psychological phenomenon where sensory signals become mixed. Input to one sensory modality produces an experience in a second, unstimulated modality. In “grapheme-color synesthesia”, viewed letters and numbers evoke mental imagery of colors. The study of this condition has implications for increasing our understanding of brain architecture and function, language, memory and semantics, and the nature of consciousness. In this work, we propose a novel application deep learning to model perception in grapheme-color synesthesia. Achromatic letter images, taken from database of handwritten characters, are used to induce synesthesia. Results show the model learns to accurately create a colored version of the inducing stimulus, according to a statistical distribution from experiments on a sample population of grapheme-color synesthetes. The spontaneous, creative mental imagery characteristic of the synesthetic perceptual experience is reproduced by the model. A model of synesthesia that generates testable predictions on brain activity and behavior is needed to complement large scale data collection efforts in neuroscience, especially when articulating simple descriptions of cause (stimulus) and effect (behavior). The research and modeling approach reported here begins to address this need.

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

Organ-on-a-chip (OOC) is an emerging technology that simulates an artificial organ within a microfluidic cell culture chip. Current cell biology research focuses on in vitro cell culture due to various limitations of in vivo testing. Unfortunately, in vitro cell culture fails to provide an accurate microenvironment, and in vivo cell culture is expensive and has historically been a source of ethical controversy. OOC aims to overcome these shortcomings and provide the best of both in vivo and in vitro cell culture research. The key component of the OOC design is utilizing microfluidics to ensure a stable concentration gradient, dynamic mechanical stress modeling, and accurate reconstruction of a cellular microenvironment. OOC also has the advantage of complete observation and control of the system, which is impossible to recreate in in vivo research. Multiple throughputs, channels, membranes, and chambers are constructed in a polydimethylsiloxane (PDMS) array to simulate various organs on a chip. Various experiments can be performed utilizing OOC technology, including drug delivery research and toxicology. Current technological expansions involve multiple organ microenvironments on a single chip, allowing for studying inter-tissue interactions. Other developments in the OOC technology include finding a more suitable material as a replacement for PDMS and minimizing artefactual error and non-translatable differences.

Esophageal adenocarcinoma (EAC) detection relies on endoscopy-biopsy diagnosis, with routine endoscopic surveillance recommended for Barrett’s esophagus (BE) patients. Here, we examine the utility of blood biomarkers in patient risk stratification by translating the EAC blood biomarker Jacalin lectin binding complement C9 (JAC-C9) into a novel microfluidic immunoassay, the EndoScreen Chip. Cohort evaluation (n=46) showed elevated serum total C9 and JAC-C9 in EAC. Logistic regression modeling demonstrated that addition of C9 and JAC-C9 to patient risk factors (age, body mass index and heartburn/reflux history) improved EAC prediction from AUROC of 0.838 to 0.931. Serum JAC-C9 strongly predicted EAC (vs BE OR= 4.6, 95% CI: 1.6-15.6, p = 0.014; vs Healthy OR=4.1, 95% CI:1.2-13.7, p = 0.024) while total C9 was moderately predictive for BE (vs EAC OR=1.4; 95% CI: 1.0-1.8, p = 0.032; vs Healthy OR=0.8; 95% CI: 0.6-1.0, p = 0.039). This translational study demonstrates the potential utility of blood biomarkers in improving triaging for diagnostic endoscopy.

This study compared the use of chip and slash to minimize the loss of sediment on newly constructed forest road slopes and investigated the annual amount of sediment loss on bare forest road slopes. A runoff block (sample field) was established for each of the four designated test sites (two cutslopes and two fillslopes). Each block had three runoff plots. One of the runoff plots was left empty for the control (CNT), while chip (C) and slash (S), respectively, were deposited in the other two. A total of 108 water samples were taken from the test sites and the amount of their suspended sediment calculated in the laboratory. As a result of this study, it was determined that the amount of soil loss in the control plots was about 1.26 times higher than in the slash plots and 2.21 times higher than in the chip plots. According to the results of variance analysis on the amounts of sediment, a statistically significant difference was found between the suspended sediment quantities transported on the road slopes (P <0.05). However, no statistically significant difference between the suspended sediment quantities transported in the plots and the other variables of aspect, gradient or road slope was revealed by the t-test (P >0.05).

The effect of fungicides on fermentation is of paramount importance to control the quality and safety of wines. In this work, the quality (oenological parameters, color, phenolic content, antioxidant activity, and fungicide residues) of wines from Monastrell grapes fortified with iprovalicarb, mepanipyrim and tetraconazole fungicides was evaluated. Along of the winemaking process, initial residues of mepanipyrim and tetraconazole were removed in more than a 90 % while dissipation of iprovalicarb was around 73 %. Significant statistical differences were found in presence of iprovalicarb and mepanipyrim residues especially at the highest concentration assayed. For both fungicides, an increase of the volatile acidity (between 4 and 8.6 times), the lactic acid content (between 8.6 and 20.5 times), the percentage of polymeric anthocyanins (between 1.3 and 1.7 times) and also a slight increase of the total phenolic index and the total anthocyanins content determined by spectrophotometry was observed. On the contrary, the total monomeric anthocyanins content decreased about 16.3 and 28.6 % in presence of iprovalicarb and mepanipyrim, respectively. These results could be related with the addition of SO2 to the grape must and a higher development of acetic acid or lactic bacteria in presence of these fungicides. The color of the final wines was also different in comparison with the control, with a higher yellow component, color intensity, tonality and hue angle, because of pH changes in the medium. Tetraconazole fermentations had a more similar trend to the control wine, probably due to the lower concentration of this fungicide in the grape must at the initial time. No effects on the antioxidant activity was observed for anyone of the target fungicides. A multivariate statistical analysis was done to view interrelationships between different variables (color and anthocyanins profile). The obtained model allowed to separate wines according to the fungicide treatment applied.

This study investigates the effects of ambient illumination and negatively polarized text color on visual fatigue, exploring the issue of visual fatigue when using visual display terminals in low-illumination environments. The research methodology utilized an experimental design to collect data on changes in pupil accommodation and blink rate through an eye tracker. Partici-pants completed a reading task while exposed to various text colors and ambient light conditions to evaluate visual fatigue and cognitive performance. The study's findings suggest that text color significantly affects visual fatigue, with red text causing the highest level of visual fatigue and yellow text causing the lowest level of visual fatigue. Improvements in ambient lighting reduce visual fatigue, but the degree of improvement varies depending on the text color. Additionally, cognitive performance is better when using yellow and white text but worse when using red text. Yellow text is the most effective choice for reducing visual fatigue under negative polarity. In-creasing ambient lighting can also improve visual fatigue in low-illumination conditions. These findings will offer valuable guidance for designing visual terminal device interfaces, especially for low-illumination or night environments, to minimize visual fatigue and improve the user ex-perience.

This research assesses the classification of Arabic coffee into three primary variations (light, medium, and dark) using simulated data based on actual measurements of color information, antioxidant laboratory tests, and chemical composition tests. Two types of simulated data were generated, with the standard deviation of the measures varied. Multiple classifiers were used for classification. The findings demonstrate the use of color information in accurately distinguishing Arabic coffee types. The different CIE color values, as well as the excellent connection between color information and coffee classes, lead to flawless classification results. However, depending primarily on antioxidant information results in lower classification performance, with variability amongst classifiers due to increasing data complexity. Chemical composition information, on the other hand, possesses outstanding discriminatory strength, allowing faultless classification on its own. Certain characteristics, such as crude protein and crude fiber, show strong correlations and are critical in the classification of coffee types. Based on the findings, it is recommended to create a mobile application that uses image recognition to analyze coffee color while providing chemical composition information. End users, such as consumers, will be able to make informed judgments regarding their coffee preferences owing to this application.

In this study, we propose a solution process for realizing color glass for building integrated pho-tovoltaic (BIPV) systems by spin coating a color solution composed of a pearlescent pigment mixed in a norland optical adhesive (NOA) matrix. Color solutions are made from mixing pearlescent pigments in NOA63. Compared to a physical vapor deposition process, color coatings are achieved by spin coating in a relatively simple and inexpensive process at room temperature. The optical properties can be easily controlled by adjusting the spin coating speed and the concentra-tion of the pearlescent pigments. The produced color glasses achieved a high transmittance of 85% or more in the visible wavelength range, except the wavelength spectrum exhibiting the maxi-mum reflectance. In addition, we propose a one-step lamination process of color glass on a solar cell by leveraging on the adhesive property of the NOA matrix. This eliminates the cost and pro-cess of additional ethylene vinyl acetate (EVA) layer or other materials used in the conventional lamination process. The color glass produced through this study has stability that does not change its properties over time. Therefore, it is expected to be applied to the BIPV solar module market where aesthetics and energy efficiency are required.

Color can direct visual attention to specific locations through bottom-up and top-down mechanisms. Using Continuous Flash Suppression (CFS) as way to investigate the factors that gate access to consciousness, the current study investigated whether color also directly affected the timing of conscious perception. Low or high spatial frequency (SF) gratings with different orientations were shown as targets to the non-dominant eye of human participants. CFS patterns were presented at a rate of 10Hz to the dominant eye to delay conscious perception of the targets, and participants had the task to report the target’s orientation as soon as they could see it. With low-SF targets, two types of color-based effects became evident. First, when the targets and the CFS patterns had different colors, the targets entered consciousness faster than in trials where the targets and CFS patterns had the same color. Second, when participants searched for a specific target color, targets that matched these search settings entered consciousness faster compared to conditions where the target color was irrelevant and could vary from trial to trial. Thus, the current study demonstrates that color is a central feature of human perception and leads to faster conscious perception of visual stimuli through bottom-up and top-down attentional mechanisms.

This paper introduces a new destriping algorithm for remote sensing data. The method is based on combined Haar Stationary Wavelet transform and Fourier filtering. State-of-the-Art methods based on the discrete wavelet transform (DWT) may not always be effective and may cause different artifacts. Our contribution is three-fold: i) we propose to use the Undecimated Wavelet transform (UWT) to avoid as much as possible shortcomings of the classical DWT; ii) we combine a spectral filtering and UWT using the simplest possible wavelet, the Haar basis, for a computational efficiency; iii) we handle 2D fields with missing data, as commonly observed in ocean remote sensing data due to atmospheric conditions (e.g., cloud contamination). The performances of the proposed filter are tested and validated on the suppression of horizontal strip artifacts in cloudy L2 Sea Surface Temperature (SST) and ocean color snapshots.

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

Nepal, primarily an agricultural country, heavily relies on agricultural residue and fuelwood for daily energy requirements. In 2022, total energy consumption was 640 PJ, with traditional sources accounting for 64.17%, and fuelwood comprising 58.53% of total fuel consumption. The estimated potential supply of agricultural residue is 26 million tonnes, yielding about 442 million GJ of energy in 2021. Biomass trading often emphasizes volume or weight, necessitating a rapid and non-destructive assessment of energy properties for mutual benefit, aiding in the identification, management, and utilization of biomass sources. In this study, 200 biomass samples were collected in two batches (126 and 74 samples) from various locations in Nepal. Using Partial Least Squares Regression (PLSR), a model was developed correlating higher heating value (HHV) from a bomb calorimeter and spectral data from Fourier Transform near-infrared spectroscopy (FT-NIRS) (3595 – 12,489 cm-1) sensor. PLSR models incorporated raw spectra, eight preprocessing techniques, the multi-preprocessing five-range method, and a genetic algorithm. Outliers in the first batch were identified, and the first batch divided into an 80% calibration set and a 20% validation set, while the second batch was designated as an unknown sample set. The optimum PLSR model, utilizing first derivative preprocessing, improved accuracy by 6.77%, with coefficients of determination in the calibration set, validation set, and unknown set as 0.9694, 0.9578, and 0.8089, respectively. Root mean square errors were 132.4790 J/g, 189.4800 J/g, and 360.8845 J/g for the calibration set (RMSEC), validation set (RMSEP), and unknown set (RMSEUN), respectively. The prediction to deviation ratio (RPD) for the validation set and unknown set was 4.9 and 2.4, respectively. The cross validation model of combined sample data of every sets showed the R2CV of 0.95 and RPDCV of 4.6 indicating the model could serve as a reliable and swift non-destructive alternative for evaluating biomass HHV using NIRS and ready for updating for industrial use. However, incorporating a larger number of representative samples is crucial to enhance accuracy and develop a more comprehensive global model for predicting biomass HHV.

This study develops a vitamin C controlled-release system trackable via color changes as a function of vitamin C release. The system is composed of coaxial microfibers prepared via coaxial electrospinning, with a core of poly(ethylene oxide) (PEO) incorporating vitamin C, and a shell composed of polycaprolactone (PCL) containing polydiacetylene (PDA) as the color-changing material. The shell thickness was controlled by adjusting the amount of PCL ejected during electrospinning, allowing the regulation of the release rate of vitamin C. When vitamin C added to PEO penetrated the PCL layer, the color of PDA changed from blue to red, indicating a color change. The results of this study can be applied to devices that require immediate detection of vitamin C release levels.

Some recent studies show that filters in convolutional neural networks (CNNs) have low color selectivity in datasets of natural scenes such as Imagenet. CNNs, bio-inspired in the visual cortex, are characterized by their hierarchical learning structure, which appears to gradually transform the representation space. Inspired by the direct connection between the LGN and V4, which allows V4 to handle low-level information closer to the trichromatic input in addition to processed information that comes from V2/V3, we propose the addition of a long skip connection (LSC) between the first and last blocks of the feature extraction stage to allow deeper parts of the network to receive information from shallower layers. This type of connection improves classification accuracy by combining simple-visual and complex-abstract features to create more color-selective ones. We have applied this strategy to classic CNN architectures and quantitatively and qualitatively analyzed the improvement in accuracy while focusing on color selectivity. The results show that, in general, skip connections improve accuracy, but LSC improves it even more and enhances the color selectivity of the original CNN architectures. As a side result, we propose a new color representation procedure for organizing and filtering feature maps, making their visualization more manageable.

Single sample face recognition (SSFR) is a computer vision challenge. In this scenario, there is only one example from each individual on which to train the system, making it difficult to identify persons in unconstrained environments, particularly when dealing with changes in facial expression, posture, lighting, and occlusion. This paper suggests a different method based on a variant of the Binarized Statistical Image Features (BSIF) descriptor called Multi-Block Color-Binarized Statistical Image Features (MB-C-BSIF) to resolve the SSFR Problem. First, the MB-C-BSIF method decomposes a facial image into three channels (e.g., red, green, and blue), then it divides each channel into equal non-overlapping blocks to select the local facial characteristics that are consequently employed in the classification phase. Finally, the identity is determined by calculating the similarities among the characteristic vectors adopting a distance measurement of the k-nearest neighbors (K-NN) classifier. Extensive experiments on several subsets of the unconstrained Alex &amp; Robert (AR) and Labeled Faces in the Wild (LFW) databases show that the MB-C-BSIF achieves superior results in unconstrained situations when compared to current state-of-the-art methods, especially when dealing with changes in facial expression, lighting, and occlusion. Furthermore, the suggested method employs algorithms with lower computational cost, making it ideal for real-time applications.

Oenothera flower petals change color during senescence. When in full bloom, the flowers of O. tetraptera are white and those of O. laciniata and O. stricta are yellow; however, the colors change to pink and orange, respectively, when the petals fade. We analyzed the flavonoid components in these petals as a function of senescence using HPLC-DAD and LC-MS. In all three species, cyanidin 3-glucoside (Cy3G) was found in faded petals, and the content of Cy3G increased in senescence. In full bloom (0 h), no Cy3G was detected in any of the petals, but after 12 h, the content of Cy3G in O. tetraptera was 0.97 μmol/gFW and that in O. laciniata was 1.82 μmol/gFW. Together with anthocyanins, major flavonoid components in petals were identified. Quercitrin was detected in the petals of O. tetraptera, and isosalipurposide was found in the petals of O. laciniata and O. stricta. The content of quercitrin did not change during senescence, but that of isosalipurposide in O. laciniata increased from 3.4 μmol/gFW at 0 h to 4.8 μmol/gFW at 12 h. The color change in all the three Oenothera flowers was confirmed to be due to the de novo biosynthesis of Cy3G.

Although the effect of thermal modification (TM) on teak wood color is well documented, a few studies were carried out in closed system processes, as well as it remains unclear the effect of different processes on the same material. This work aimed to verify the effect of closed and open system processes of TM on the color of fast-growing teak wood. Thermally modified wood was evaluated in a closed system at 160 °C (CS160) and in an open system at 185 °C and 210 °C (OS185 and OS210). We measured the moisture content (initial and final) of wood, and the corrected mass loss (CML). The chemical analyses encompassed the contents of alpha-cellulose, hemicelluloses, lignin, and extractives (total, in acetone and dichloromethane). Wood color was measured before and after TM according to the CIEL*a*b* color space. It was possible to achieve the same color using different processes of thermal modification (CS160 and OS210). TM reduced wood lightness (L*), red-green chromaticity coordinate (a*), and yellow-blue chromaticity coordinate (b*). L* and a* had the bigger and lower variations, respectively. The color of thermally modified wood was significantly changed, even at the mildest condition tested (OS185, 0.33% CML).

The valley pseudospin properties of electrons in two–dimensional hexagonal materials result in lots of fascinating physical phenomena, which opens up the new field of valleytronics. The valley-contrasting physics aims at distinguishing the valley degree of freedom based on valley–dependent effects. Here, we theoretically demonstrate that both of the valley–selective high harmonic generation and valley–selective electronic excitation can be achieved by using an orthogonal two–color (OTC) laser field in gapped graphene. It is shown that the asymmetry degrees of harmonic yields in the plateaus, cutoff energies of generated harmonics and electron populations from two different valleys can be precisely controlled by the relative phase of the OTC laser field. Thus the selectivity of the dominant valley for the harmonic radiation and electronic polarization can be switched by adjusting the relative phase of the OTC laser field. Our work offers an all–optical route to produce the valley–resolved high harmonic emissions and manipulate the ultrafast valley polarization on a femtosecond timescale in condensed matter.

Fusarium head blight (FHB) disease is extensively distributed worldwide. This disease damages grain quality and reduces yield. The detection of this disease in a high throughput way is crucial to planters and breeders. Our study focused on developing a method for processing wheat color images and accurately detecting disease areas using deep learning and image processing techniques. The color images of wheat at the milky stage were collected and processed to construct datasets, which were used to retrain a deep convolutional neural network model using transfer learning. Testing results showed that the model can detect spikes, and the coefficient of determination of the number of spikes between the manual count and the detection was 0.80. The model was assessed, and the mean average precision for the testing dataset was 0.9201. On the basis of the results of spike detection, a new color feature was applied to obtain the gray image of each spike. Then, a modified region growing algorithm was implemented to segment and detect the diseased areas of each spike. Results show that the region growing algorithm performs better than K-means and Otsu’s method in segmenting the FHB disease. Overall, this study demonstrates that deep learning techniques enable the accurate detection of FHB in wheat using color images, and the proposed method can effectively detect spikes and diseased areas, thereby improving the efficiency of FHB detection.

The detection of temporary color steel buildings and the analysis of their spatiotemporal patterns and characteristics are of great importance in many developing cities, because areas densely distributed with color steel buildings are usually problematic regions with high population density, sustainable development and risk level, which are challenging for local governments. Using the high-resolution satellite images of the Anning District, Lanzhou City, China as the case study, this paper first extracts the information of the color steel buildings for two different periods. Then the spatiotemporal distributional characteristics of the color steel buildings are analyzed, both at small scale (temporary buildings) and large scale (planthouses, warehouses, etc.). Finally, this paper utilizes kernel density estimation, Delaunay triangulation and Voronoi diagrams to examine the spatial distribution, aggregation and proximity characteristics of the color steel buildings. Our experiments show that the temporal and spatial differences of urban development, the phased characteristics and urban space are represented by various types of color steel buildings. Thus, there are some robust coupling relationship between color steel buildings, urban spatial form and urban development.

Diffuse correlation spectroscopy (DCS) is a non-invasive technology for the evaluation of the blood perfusion in deep tissue. However, it requires high computational resources for data analysis which poses challenges in its implementation for real-time applications. To address the unmet need, we developed a novel device-on-chip solution that fully integrates all the necessary computational components needed for DCS. It takes the output of a photon detector and determines the blood flow index (BFI). It is implemented on a Field Programmable Gate Array (FPGA) chip including a multi-tau correlator for the calculation of the temporal light intensity autocorrelation function and a DCS analyzer to perform the curve fitting operation that derives the BFI. The FPGA DCS system was evaluated against a lab-standard DCS system for both phantom and cuff-ischemia studies. The results indicate that the autocorrelation of the light correlation and BFI from both the FPGA DCS and the reference DCS matched well. Furthermore, the FPGA DCS system was able to achieve a measurement rate of 50 Hz and resolve pulsatile blood flow.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Polymerase chain reaction (PCR) technique is one of the molecular methods in amplifying DNA for the detection of malaria. However, the limitations of PCR especially when used for routine clinical practice can hamper its sensitivity and specificity. With that, this study focuses on designing a microfluidic device that will mimic the function of a conventional genus-specific PCR based on 18S rRNA gene to detect malaria parasites (Plasmodium falciparum) at low grade parasitemia. The design was drawn and simulated using ANSYS 14.5 Computational Fluid Dynamics (CFD). The simulation shows that adding loops to the design increases its relative deviation but to a minimal extent as compared to having only a straight path design, which indicates that looping is acceptable in designing a microfluidic device to minimize chip length. Also, increasing the cross-sectional area of the fluid path decreases the efficiency of the design, thus, the design with a relatively smaller cross-sectional area is favored. And lastly, among the three materials utilized, the chip made of polypropylene is the most efficient with a relative deviation of 0.94 as compared to polycarbonate and polydimethylsiloxane which have relative deviations of 2.78 and 1.92, respectively.

Understanding cell migration is a key step to unravel many physiological phenomena and predict several pathologies, like cancer metastasis. In particular, mechanical confinement has been proved to be a key factor in the cellular migration strategy choice. As our insight in the field improves, new tools are needed in order to empower biologists’ analysis capabilities. In this framework, microfluidic devices have been used to engineer the mechanical stimuli and to investigate cellular migration response in a more controlled way. In this work, we will review the existing technologies employed in the realization of microfluidic cellular migration assays, namely soft lithography of PDMS and hydrogels and femtosecond laser micromachining. We will give an overview of the state of the art of these devices, focusing on the different geometrical configurations that have been exploited to study specific aspects of cellular migration. Our scope is to highlight the advantages and possibilities given by each approach and to envisage the future developments in in-vitro migration studies under mechanical confinement in microfluidic devices.

The liquid droplet cooling technique for fast scanning chip calorimetry (FSC) is introduced, increasing the cooling rate for large samples on a given sensor. Reaching higher cooling rates and using a gas as the cooling medium, the common standard for ultra-fast temperature control in cooling, requires reducing the lateral dimensions of the sample and sensor. The maximum cooling rate is limited by the heat capacity of the sample and the heat exchange between the gas and the sample. The enhanced cooling performance of the new liquid droplet cooling technique is demonstrated for both metals and polymers, on examples of solidification of large samples of indium, high-density polyethylene (HDPE), and poly (butylene 2,6-naphthalate) (PBN). It was found that the maximum cooling rate can be increased up to 5 MK/s in room temperature environment, that is, by 2 orders of magnitude, compared to standard gas cooling. Furthermore, modifying the droplet size and using coolants at different temperatures provide options to adjust the cooling rate in the temperature ranges of interest.

We report world record high data transmission over standard optical fiber from a single optical source. We achieve a line rate of 44.2 Terabits per second (Tb/s) employing only the C-band at 1550nm, resulting in a spectral efficiency of 10.4 bits/s/Hz. We use a new and powerful class of micro-comb called soliton crystals that exhibit robust operation and stable generation as well as a high intrinsic efficiency that, together with an extremely low spacing of 48.9 GHz enables a very high coherent data modulation format of 64 QAM. We achieve error free transmission across 75 km of standard optical fiber in the lab and over a field trial with a metropolitan optical fiber network. This work demonstrates the ability of optical micro-combs to exceed other approaches in performance for the most demanding practical optical communications applications.

Collision avoidance is an important feature in advanced driver-assistance systems, aiming at providing correct, timely and reliable warnings before an imminent collision (objects, vehicles, pedestrians, etc.). A co-simulation framework is proposed in this paper to address the design and evaluation of collision avoidances in a cyber-physical system. The co-simulation framework is supported on the interaction between SCANeR and Matlab/Simulink. From the best of authors’ knowledge, two main contributions are reported in this paper. Firstly, the modelling and simulation of virtual on-chip LIDAR sensors in a cyber-physical system (CPS) considering traffic scenarios is presented. The CPS is designed and implemented in SCANeR. Secondly, an obstacle recognition library with three specific Artificial Intelligence-based methods is also designed based on sensory information database provided by SCANeR. Three methods for collision avoidance detection are considered, i.e.; a multi-layer perceptron neural network, a self-organization map and a support vector machine. Finally, a comparison among these methods for detecting obstacles before different weather conditions is done with very promising results in terms of accuracy. The best results are achieved using the multi-layer perceptron in sunny and fog conditions, the support vector machine in rainy and self-organized map in snowy conditions.

Graphene-based Field-Effect Transistors (FETs) integrated with microstrip patch antennas offer a promising approach for Terahertz signal radiation. In this study, a dual-stage simulation methodology is employed to comprehensively investigate the device’s performance. The initial stage, executed in MATLAB, delves into charge transport dynamics within a FET under asymmetric boundary conditions, employing hydrodynamic equations for electron transport in the graphene channel. Electromagnetic field interactions are modeled via Finite-Difference Time-Domain (FDTD) techniques. The second stage, conducted in COMSOL Multiphysics, focuses on the microstrip patch antenna’s radiative characteristics. Notably, analysis of the S11 curve reveals minimal reflections at the FET’s resonant frequency of 1.34672 THz, indicating efficient impedance matching. Examination of the radiation pattern demonstrates the antenna’s favorable directional properties. This research underscores the potential of graphene-based FETs for Terahertz applications, offering tunable impedance matching and high radiation efficiency for future Terahertz devices.

The Double Random Phase Encoding (DRPE) image encryption method has garnered significant attention in color image processing and optical encryption, thanks to its parallel encryption of R, G, B. However, DRPE-based color image encryption faces two challenges. Firstly, it disregards the correlation of R, G, and B, compromising the encrypted image's robustness. Secondly, DRPE schemes relying on Discrete Fourier Transform (DFT) and Discrete Fractional Fourier Transform (DFRFT) are vulnerable to linear attacks, such as Known Plaintext Attack (KPA) and Chosen Plaintext Attack (CPA). Quantum walk stands out as a remarkable tool for designing modern cryptographic mechanisms, offering resistance to potential attacks from both classical and quantum computers.Therefore, this study presents an optical color image encryption algorithm that combines two-dimensional quantum walk with 24-bit plane permutation, dubbed OCT. This approach employs pseudo-random numbers generated by Two-Dimensional Quantum Walking (TDQW) for phase modulation in DRPE and scrambles the encrypted image's real and imaginary parts using the Generalized Arnold Transform. The 24-bit plane permutation helps reduce correlation of the R, G, B, while the Generalized Arnold Transform bolsters DRPE's resistance to linear attacks. By incorporating TDQW, the key space is significantly expanded. Experimental results validate the effectiveness and security of proposed method.

The Ocean Color - Simultaneous Marine and Aerosol Retrieval Tool (OC-SMART) is a robust data processing platform that supports a large array of multi-spectral and hyper-spectral sensors. It provides accurate aerosol optical depths and remote sensing reflectances (Rrs estimates) that can be used to generate products such as absorption coefficients due to phytoplankton and detritus/Gelbstoff as well as backscattering coefficients due to particulate matter. The OC-SMART platform yields improved performance in complex environments by utilizing scientific machine learning (SciML) in conjunction with comprehensive radiative transfer computations. This paper expands the capability of OC-SMART by quantifying uncertainties in ocean color retrievals. Bayesian inversion is used to relate measured top of atmosphere radiances and a priori data to estimate posterior probability density functions and associated uncertainties. A framework of the methodology and implementation strategy is presented and uncertainty estimates for Rrs retrievals are provided to demonstrate the approach by applying it to MODIS, OLCI Sentinel-3, and VIIRS sensor data.

The largest part of the image encryption algorithms operates on the pixel as a central element by implementing diffusion confusion and eventually a permutation. On the other side, a permutation applied at the bit level changes not only the pixel value, but also its location within the image. In this work, we will propose a new technology of medical and color image encryption, based on chaotic permutations acting at the bit level, and a diffusion confusion ensured by an application of the method of Vigenere largely improved and adapted to the subject. Simulations performed on a large number of images of different sizes and formats ensure that our method is not subject to any known attacks.

We investigated layered titanium nitride (TiN) and aluminum nitride (AlN) for color glasses in Building Integrated Photovoltaic (BIPV) systems. AlN and TiN are among suitable and cost-effective optical materials to be used as thin multilayer films, owing to the significant difference in their refractive index. To fabricate the structure, we used radio frequency magnetron deposition method to achieve the target thickness uniformly. A simple, fast, and cheap fabrication method is achieved by depositing the multilayer films in a single sputtering chamber. It is demonstrated that a multilayer stack that allows light to move from a low refractive index layer to a high refractive index layer or vice-versa can effectively create various distinct color reflections for different film thicknesses and multilayer structures. It is investigated from simulation based on wave optics that, TiN/AlN multilayer offers better color design freedom and cheaper fabrication process as compared to AlN/TiN multilayer films. Blue, green, and yellow color glasses with optical transmittance of more than 80% was achieved by ITO coated glass/TiN/AlN multilayer films. This technology exhibits good potential in commercial BIPV system applications.

Victor Vasarely’s (1906-1997) important legacy to the study of human perception is brought to the forefront and discussed. A large part of his impressive work conveys the appearance of striking three-dimensional shapes and structures in a large-scale pictorial plane. Current perception science explains such effects by invoking brain mechanisms for the processing of monocular (2D) depth cues. Here in this study, we illustrate and explain the local effects of 2D color and contrast cues on the perceptual organization in terms of figure-ground assignments, i.e. which local surfaces are likely to be seen as “nearer” or “bigger” in the image plane. Paired configurations are embedded in a larger, structurally ambivalent pictorial context inspired by some of Vasarely’s creations. The figure-ground effects these configurations produce reveal a significant correlation between perceptual solutions for “nearer” and “bigger” when no other monocular depth cues are given in the image. In consistency with previous findings on similar, albeit simpler visual displays, a specific color may compete with luminance contrast in resolving the planar ambiguity of a complex pattern context. Vasarely intuitively understood, and successfully exploited, this kind of subtle context effect in his art, well before empirical investigations had set out to study and explain their genesis in terms of information processing by the visual brain.

This paper offers a novel geometric and visual approach to the renowned Four Color Map Theorem and K5 non-planarity problem while unveiling their profound connection to the "kissing number" problem in 2D. We represent planar graphs through circles and tangents, simplifying complex structures and shedding light on these classic problems. Our proofs by contradiction, rooted in the kissing number concept, reveal that both the Four Color Map Theorem and K5 non-planarity are fundamentally linked, as they pivot around the concept of coloring. This study bridges the realms of geometry and graph theory, providing fresh insights and emphasizing the significance of the kissing number problem in various fields.

Data from ocean color (OC) remote sensing are considered a cost-effective tool for the study of biogeochemical processes globally. Satellite-derived chlorophyll, for instance, is considered an Essential Climate Variable since it is helpful in detecting climate change impacts. Google Earth Engine (GEE) is a planetary scale tool for remote sensing data analysis. Along with OC data, such tools allow an unprecedented spatial and temporal scale analysis of water quality monitoring in a way that has never been done before. Although OC data have been routinely collected at medium (~1 km) and more recently at high (~250 m) spatial resolution, only coarse resolution (≥4 km) data are available in GEE, making them unattractive for applications in the coastal regions. Data reprojection is needed prior to making OC data readily available in the GEE. In this paper, we introduce a simple but practical procedure to reproject and ingest OC data into GEE. The procedure is applicable to OC swath (Level-2) data and is easily adaptable to higher-level products. The results showed consistent distributions between swath and reprojected data, building confidence in the introduced framework. The study aims to start a discussion on making high resolution OC data readily available in GEE.

In order to realize rapid and nondestructive monitoring of wheat biomass in field, field experiments based on different densities, nitrogen fertilizer and variety treatments were studied. RGB images of wheat in the main growth stage were obtained by UAV, and wheat color and texture feature indices were obtained by image processing, and wheat biomass was obtained by field sampling in the same period. Then the relationship between different color and texture feature indices and wheat biomass was analyzed to select the color and texture feature index suitable for wheat biomass estimation. The results showed that there was a high correlation between image color index and wheat biomass in different stages, and most of them reached a very significant correlation level. However, the correlation between image texture feature index and wheat biomass was poor, only a few indexes reached significant or extremely significant correlation level. Based on the above results, the color indices with the highest correlation to wheat biomass or the combining indices of color and texture feature in different growth stage were used to construct estimation model of wheat biomass. The models were validated using independently measured biomass data, and the correlation between simulated and measured values reached the significant level, RMSE were smaller. This indicated that the estimated results by the models were reliable and accurate. It also showed that the estimation models of wheat biomass combined with color and texture feature indices of UAV image were better than the single color index models. The results would provide a new method for real-time monitoring of wheat field growth and biomass estimation.

With continued technological innovation in the fields of mixed reality (MR), wearable-type MR devices, such as helmets, have been released and are frequently used in various fields, such as entertainment, training, and education. However, because each product has different parts and specifications in terms of the design and manufacturing process, users feel that the virtual objects overlaying real environments in MR are visualized differently depending on the scale and color used by the MR device. In this paper, we compare the effect of scale and color parameters on users’ perception in using different types of MR devices to improve MR experience. We conducted two experiments (scale and color), and our experimental study showed that the subjects who participated in the scale perception experiment clearly tended to underestimate virtual objects, compared with real objects, and overestimate color in MR environments. [MM1]Please confirm meaning.

In this work, an evanescent Bragg grating sensor inscribed in a few-mode planar polymer waveguide was integrated in microchannel structures and characterized with various chemical applications. The planar waveguide and the microchannels consisted of epoxide-based polymers. The Bragg grating structure was post-processed using point-by-point direct inscription technology. By monitoring the central wavelength shift of the reflected Bragg signal, the sensor showed a temperature sensitivity of -47.75 pm/K. Moreover, the functionality of the evanescent field-based measurements is demonstrated with two application examples: refractive index sensing of different aqueous solutions and gas-phase hydrogen concentration detection. For the latter application, the sensor was additionally coated with a functional layer based on palladium nanoparticles. During the refractive index sensing measurement, the sensor achieved a sensitivity of 6.5 nm/RIU from air to 99.9% pure isopropyl alcohol. For the gas-phase hydrogen detection, the coated sensor achieved a reproducible concentration detection up to 4 vol% hydrogen. According to the reported experimental results, the integrated Bragg grating-based waveguide sensor demonstrates high potential for applications based on lab-on-a-chip concept.

For Convolutional Neural Network (CNN), Depthwise Separable CNN (DSCNN) is a preferred architecture for Application Specific Integrated Circuit (ASIC) implementation on edge devices. It can benefit from a multi-mode approximate multiplier proposed in this work. The proposed approximate multiplier uses two 4-bit multiplication operations to implement a 12-bit multiplication operation by reusing the same multiplier array. With this approximate multiplier, sequential multiplication operations are pipelined in a modified DSCNN to fully utilize the PE array in the convolutional layer. This Approximate (A-DSCNN) was implemented on TSMC 40-nm CMOS process with a supply voltage of 0.9 V. At the clock frequency of 200 MHz, the design achieves 4.78 GOPs/mW while occupying 1.24 mm x 1.24 mm silicon area. Compared to conventional DSCNN implemented in a similar process node, the chip area and power consumption were reduced by 53% and 25%, while the throughput was improved by 17%.

Microfluidic lab-on-chip devices are widely being developed for chemical and biological studies. One of the most commonly used types of these chips is perfusion microwells for culturing multicellular spheroids. The main challenge in such systems is the formation of substantial necrotic and hypoxic zones within the cultured spheroids. Herein, we propose a novel acoustofluidic integrated platform to tackle this bottleneck problem. We show that such an approach enhances cell viability and shrinks necrotic and hypoxic zones in these spheroid-on-a-chip platforms without the need to increase the flow rate, leading to a significant reduction in costly reagents' consumption. Proof-of-concept, designing procedures, and finite element numerical simulation are discussed in details. Also, the effects of acoustic and hydrodynamic parameters on the cultured cells are investigated. The results show that by increasing acoustic boundary displacement amplitude (d0), the spheroid’s proliferating zone enlarges greatly. Moreover, it is shown that by implementing d0=0.5 nm, the required flow rate to maintain the necrotic zone below 13% will be decreased 12 times compared to non-acoustic chips.

We report on the application of femtosecond laser micromachining to the fabrication of complex glass microdevices, for high-order harmonic generation in gas. The three-dimensional capabilities and extreme flexibility of femtosecond laser micromachining allow us to achieve accurate control of gas density inside the micrometer interaction channel. This device gives a considerable increase in harmonics generation efficiency if compared with traditional harmonic generation in gas jets. We propose different chip geometries that allow to control the gas density and driving field intensity inside the interaction channel to achieve quasi-phase matching conditions in the harmonic generation process. We believe that these glass micro-devices will pave the way to future downscaling of High-order Harmonic Generation beamlines.

We previously reported how the loss of CHIP expression (Carboxyl terminus of Hsc70-Interacting Protein) during pressure overload resulted in robust cardiac dysfunction, accompanied by a failure to maintain ATP levels in the face of increased energy demand. In this study, we analyzed the cardiac metabolome after seven days of pressure overload and found an increase in long- and medium-chain fatty acid metabolites in wild-type hearts, a response that was attenuated in mice that lack expression of CHIP (CHIP^-/-). These findings suggest that CHIP may play an essential role in regulating oxidative metabolism, pathways that are regulated in part by the nuclear receptor PPARα (Peroxisome Proliferator-Activated Receptor alpha). Next, we challenged CHIP^-/- mice with the PPARα agonist, fenofibrate. Surprisingly, treating CHIP^-/- mice with fenofibrate for five weeks under non-pressure overload conditions resulted in a loss of skeletal muscle mass and a marked increase in cardiac fibrosis, accompanied by a decrease in cardiac function. Isolated CHIP^-/- cardiac fibroblasts treated with fenofibrate did not increase synthesis of collagen or TGFβ, suggesting that the fibrosis observed in CHIP^-/- hearts likely depends on signaling from other cell types or circulating factors. In conclusion, in the absence of functional CHIP expression, fenofibrate results in unexpected cardiac pathologies. These findings are particularly relevant to patients harboring loss-of-function mutations in CHIP and are consistent with a prominent role for CHIP in regulating cardiac metabolism.

Screening and early diagnosis of diseases are crucial for a patient's treatment to be successful and to improve their survival rate, especially in cancer. The development of non-invasive analytical methods able to detect biomarkers of pathologies is a critical point to define a successful treat-ment and a good outcome. This study extensively reviews electrochemical methods used for the development of biosensors in liquid biopsy, owing to their ability to provide rapid response, pre-cise detection, and low detection limits. We also discuss new developments in electrochemical biosensors, which can improve the specificity and sensitivity of standard analytical procedures. Electrochemical biosensors demonstrate remarkable sensitivity in detecting minute quantities of analytes, encompassing proteins, nucleic acids, and circulating tumor cells, even within challeng-ing matrices such as urine, serum, blood, and various other body fluids. Among the various de-tection techniques used for the detection of cancer biomarkers, even in the picogram range, volt-ammetric sensors are deeply discussed in this review because of their advantages and technical characteristics. This widespread utilization stems from their ability to facilitate quantitative de-tection of ions and molecules with exceptional precision. The comparison of each electrochemical technique is discussed to provide the selection of appropriate analytical methods.

Blood image intensity has been used to detect erythrocyte sedimentation rate (ESR). However, it does not give an information on biophysical properties of blood sample under continuous ESR. In this study, three physical properties, including, τ₀, ESR_τ, and AI_I, are suggested to quantify mechanical variations of blood under continuous ESR. To demonstrate the proposed method, blood sample is loaded into a driving syringe. The blood flow rate is set in a periodic on–off pattern. Blood sample is then supplied into a capillary chip, and microscopic blood images are captured at specific intervals. Blood shear stress is quantified from the interface of blood stream in the coflowing channel. Both τ₀ and ESR_τ are then obtained by analyzing the blood shear stress. Simultaneously, the AI_I is evaluated by analyzing the image intensity of blood flow. According to the experimental results, the τ₀ exhibits consistent trends with respect to hematocrit as well as diluent. The ESR_τ and AI_I showed a reciprocal relationship each other. Three suggested properties represented substantial differences for suspended blood samples (i.e., hardened red blood cells, different concentration of dextran solution and fibrinogen). In conclusion, the present method can detect variations of blood sample under continuous ESR effectively.

Despite accumulating evidence for the pro-apoptotic role for X-linked inhibitor of apoptosis-associated factor 1 (XAF1), its involvement in endoplasmic reticulum (ER) stress response remains undefined. Here, we report that XAF1 enhances cell sensitivity to ER stress and acts as a switch in unfolded protein response (UPR)-mediated cell-fate decisions favoring apoptosis over adaptive autophagy. XAF1 interacts with and destabilizes ER stress sensor GRP78 through the assembly of zinc finger protein 313-mediated destruction complex. Moreover, XAF1 gene transcription is activated by ER stress through PERK-Nrf2 signaling to direct an adaptive to apoptotic switch of stress response by blocking C-terminus of Hsc70-interacting protein (CHIP)-mediated K63-linked ubiquitination and subsequent phosphorylation of inositol-required enzyme-1α (IRE1α). In tumor xenograft assays, XAF1-/- tumors display substantially lower regression compared to XAF1+/+ tumors in response to cytotoxic dose of ER stress inducer. XAF1 and GRP78 expression show an inverse correlation in human cancer cell lines and primary breast carcinomas. Collectively this study uncovers an important role for XAF1 as a linchpin to govern the sensitivity to ER stress and the outcomes of UPR signaling, illuminating the mechanistic consequence of XAF1 inactivation in tumorigenesis.

Glioblastoma (GBM) is one of the most aggressive solid tumors, particularly due to the presence of cancer stem cells (CSCs). Today the characterization of this type of cells with an efficient, fast and low-cost method remains an issue. Hence, we have developed a microfluidic lab-on-a-chip based on dielectrophoresis (DEP) single cell electro-manipulation to measure the two crossover frequencies: f_x01 in low frequency range (below 500 kHz) and f_x02 in Ultra High Frequency range (UHF, above 50 MHz). First, in vitro conditions were investigated. U87-MG cell lines were cultured in different conditions in order to induce an undifferentiated phenotype. Then, ex vivo GBM cells from patients’ primary cell culture, were passed through the developed microfluidic system and characterized in order to reflect clinical conditions. This article demonstrates that the usual exploitation of low frequency range DEP does not allow the discrimination of the undifferentiated from the differentiated phenotypes of GBM cells. However, the presented study highlights the use of UHF-DEP as a relevant discriminant parameter. The proposed microfluidic lab-on-a-chip is able to follow the kinetic of U87-MG phenotype transformation in a CSC enrichment medium and their cancer stem cells phenotype acquirement.

The diversity of leaf characteristics, including leaf color, is a prominent subject of study in plant science. Leaf color is predominantly determined by the synthesis and functionality of chlorophyll, a key component of photosynthesis. The regulation of chlorophyll synthesis and degradation involves complex gene interactions, and disruptions in these processes can lead to abnormal chlorophyll synthesis and impact leaf color. This study focuses on Bambusa multiplex f. silverstripe, a natural variant with various leaf colors, including green, white, and green-white leaves. The variations in leaf color are attributed to genetic factors and their influence on gene expression. By employing RNA-seq, we investigate the molecular mechanisms behind chlorophyll anomalies and genetic factors in Silverstripe. Our findings shed light on the complexity of gene interactions and regulatory networks that underlie leaf color diversity and provide valuable insights for future research and plant breeding.

Women of color (WoC) in the health professions encounter challenges in advancement to higher positions, disparities in wages, discrimination, lack of expectation to achieve leadership positions, and absence of extensive support networks. Articles in the literature have addressed race and/or gender in the context of professional development. However, applying an intersectionality lens or framework to better understand the contextual issues of professional development for WoC remains to be addressed. Thus, this scoping review aimed to (i) identify health professions literature that addresses disparities affecting WoC, and (ii) describe strategies and approaches to support WoC in the health professions. Methods: Literature searches were conducted in multiple databases. Three independent reviewers reviewed and screened articles for inclusion. Results: 31 articles were included - medicine(17), nursing(1), pharmacy(7), other(4), and multiple health professions(2). Key findings included underrepresentation of women and minority groups, inequities in professional advancement and leadership positions for WoC, and greater dissatisfaction and attrition among minority and women professionals. Conclusion: WoC face unique and distinct challenges and barriers in their professional careers resulting from the intersectionality of not only race and gender, but also lived experiences and opportunities. Strategies to improve diversity and representation should include an intersectionality framework or lens and be critically evaluated.

Holographic projection is a simple projection because it enlarges or reduces reconstructed images without using a zoom lens. However, one major problem associated with this projection is the deterioration of image quality as the reconstructed image enlarges. In this paper, we propose a time-division holographic projection, in which the original image is divided into blocks and the holograms of each block are calculated. Using a digital micromirror device (DMD), the holograms were projected at high speed to obtain the entire reconstructed image. However, the holograms on the DMD need to be binarized, thereby causing uneven brightness between the divided blocks. We correct this by controlling the displaying time of each hologram. Additionally, combining both the proposed and noise reduction methods, the image quality of the reconstructed image was improved. Results from the simulation and optical reconstructions show we obtained a full-color reconstruction image with reduced noise and uneven brightness.

Short-term (hours) biological and biogeochemical processes cannot be fully captured by the current suite of polar-orbiting satellite ocean color sensors, as their temporal resolution is limited to potentially one clear image per day. Geostationary sensors, such as the Geostationary Ocean Color Imager (GOCI) from the Republic of Korea, allow the study of these short-term processes because their geostationary orbits permit the collection of multiple images throughout each day. To assess the capability to detect changes in water properties caused by these processes, however, requires an understaning of the uncertainties introduced by the instrument and/or geophysical retrieval algorithms. This work presents a study of the variability during the day over a water region of low-productivity with the assumption that only small changes in the water properties occur during the day over the area of study. The complete GOCI mission data were processed using the SeaDAS/l2gen package. Filtering criteria were applied to assure the quality of the data. Relative differences with respect to the midday value were calculated for each hourly observation of the day. Also, the influence of the solar zenith angle in the retrieval of remote sensing reflectances and derived products was analyzed. We determined that the uncertainties in water-leaving “remote-sensing” reflectance ($R_\text{rs}$) for the 412, 443, 490, 555, 660 and 680 nm bands on GOCI are 8.05$\times10^{-4}$, 5.49$\times10^{-4}$, 4.48$\times10^{-4}$, 2.51$\times10^{-4}$, 8.83$\times10^{-5}$, and 1.36$\times10^{-4}$ sr$^{-1}$, respectively, and 1.09$\times10^{-2}$ mg m$^{-3}$ for the chlorophyll-a concentration (Chl-{\it a}), 2.09$\times10^{-3}$ m$^{-1}$ for the absorption coefficient of chromophoric dissolved organic matter at 412 nm ($a_{\text{g}}(412)$), and 3.7 mg m$^{-3}$ for particulate organic carbon (POC). We consider these to be the floor values for detectable changes in the water properties due to biological, physical or chemical processes.

To study the mechanism of light color on a sea urchin (Tripneustes gratilla), blue light (B, λ450nm), yellow light (Y, λ585-590nm), red light (R, λ640nm), green light (G, λ510nm), white light (W, λ400-780nm) and darkness groups (H) were set up in a seawater recirculating aquaculture system. Six different LED light color treatment groups with a photoperiod of 12 L:12 D were tested for 30 d to investigate the effects of different light colors on the feeding, growth and enzyme activities of T. gratilla (142.45±4.36 g). We found that varying LED light colors significantly impacts the feeding, growth, and enzyme activity of T. gratilla. Notably, the sea urchins in group B exhibited better growth with a weight gain rate of 39.26%, while those in group R demonstrated poorer growth with a weight gain rate of only 26%. The feeding differed significantly (P&lt;0.01) between groups B and R, with group B consuming the highest daily intake (6.03±1.69 g) and group R consuming the lowest (4.54±1.26 g). Throughout the three phases, there was no significant change in the viability of the AMS (P&gt;0.05). Conversely, pepsin viability significantly increased (P&lt;0.01) in group B. LPS viability remained consistently at the lowest level, with no notable differences in group W from those observed in group B. In group R, both AMS and pepsin viability remained lower, whereas lipase viability was noticeably higher in each phase compared to group B (P&lt;0.01). Regarding antioxidant enzymes, group R exhibited a trend of initially increasing and then decreasing CAT, SOD, and GSH-PX activities, particularly during the third stage (15-30 d), with a significant decrease observed in antioxidant enzyme activities (P&lt;0.01). The outcomes suggest that blue light positively affects the growth, feeding, digestion, and antioxidant capacity of T. gratilla in comparison to other light environments, whereas the red light has an inhibitory impact.

Intramuscular fat content (IFC) and meat color are vital indicators affecting pork quality. A significant positive correlation between IFC and redness meat color (a* value) indicates that these two traits are likely to be regulated by shared molecular pathways. To identify candidate genes, hub genes, and signaling pathways that regulate these two traits, we measured the IFC and a* value in 147 hybrid pigs and selected individuls with extreme phenotypes for transcriptome analysis. The results revealed 485 and 394 overlapping differentially expressed genes (DEGs) using DESeq2, limma, and edgeR packages affecting IFC and a* value, respectively. Weighted gene co-expression network analysis (WGCNA) identified four modules significantly correlated with IFC and a* value. Moreover, we integrated functional enrichment analysis results based on DEGs, GSEA, and WGCNA conditions to identify candidate genes, and identified 47 and 53 candidate genes affecting IFC and a* value, respectively. The protein-protein interaction (PPI) network analysis of candidate genes showed that 6 and 14 hub genes affecting IFC and a* value, respectively. These genes mainly participated in various pathways related to lipid metabolism and redox reactions. Notably, four crucial hub genes (MYC, SOX9, CEBPB, and PPAGRC1A) were shared for these two traits. After functional annotation of these four hub genes, we hypothesized that the SOX9/CEBPB/PPARGC1A axis could co-regulate lipid metabolism and myoglobin redox response. Further research on these hub genes, especially the SOX9/CEBPB/PPARGC1A axis, will help to understand the molecular mechanism of the co-regulation of IFC and a* value, which will provide the theoretical basis for improving pork quality.

Beef meat production in Uruguay is based on pasture or concentrate feeding systems, leading to differences in meat quality. The objective of this study was to compare the oxidative and color stability during refrigerated retail display of beef meat from these two systems. For this, ten Aberdeen Angus steers were reared and fed on pasture and other ten were finished on a concentrate diet. After slaughter, the Semimembranosus muscle was cut into slices and put in a refrigerated showcase for 3, 6, and 9 days simulating commercial conditions. The β-carotene, α-tocopherol, and fatty acid content were determined before the display, and the lipid and protein oxidation, color parameters, and heme iron content were determined before and during the display. Meat from steers fed pasture had a lower content of intramuscular fat, monounsaturated fatty acids, n-6/n-3 ratio, lipid and protein oxidation, L* and a* values, and a higher content of linolenic acid, DHA, total n-3, β-carotene, and α-tocopherol. In conclusion, meat from pasture-fed steers was more stable during the retail display, which can probably be explained by a higher content of antioxidant compounds, such as β-carotene and α-tocopherol, and presented a healthier fatty acid profile.

To digital grade the color fastness of fabrics after rubbing, an automatic grading method based on spectral reconstruction technology and BP neural network was proposed. Firstly, the modeling samples are prepared by rubbing the fabrics according to the ISO standard of 105-X12. Then, to comply with visual rating standards for color fastness, the modeling samples are professionally graded to obtain the visual rating result. After that, a digital camera is used to capture digital images of the modeling samples inside a closed and uniform lighting box, and the color data values of the modeling samples are obtained through spectral reconstruction technology. Finally, the color fastness prediction model for rubbing was constructed using the modeling samples data and BP neural network. The color fastness level of the testing samples was predicted using the prediction model, and the prediction results were compared with the existing color difference conversion method and curve fitting method. Experimental show that the prediction model of fabric color fastness can be better constructed using the BP neural network, where the root-mean-square error of the prediction for the training sample is 0.30, and the root-mean-square error of the prediction for the test sample is 0.25. The overall performance of the method is slightly better than the color difference conversion method, and it is significantly outperforming the curve fitting method. It can be seen that the digital rating method of fabric color fastness to rubbing based on spectral reconstruction and BP neural network has a high consistency with the visual evaluation, which will help for the automatic color fastness grading.

The color and NIR spectrum are key to build an oil estimation model, thus it requires individual olives clustering before the Sohlext oil extraction method can be applied. The objective was to analyze an OC estimation model of individual olives, based on cluster of similar color and NIR spectrum in different combination of the first and/or the second season. This study was performed with Chilean Arbequina olives in 2016 and 2017. The descriptor of the cluster consisted of the 3 color channels of c1, c2, c3 color model plus 11 reflectance points between 1710 and 1735 nm of each olive, normalized with the Z-score index. Clusters of similar color and NIR spectrum were formed with the k-means++ algorithm, leaving a sufficient amount of olives to be able to perform the Sohlext analysis of OC, as reference value. The estimation models were based on the Support Vector Machine. The test was carried out with the Leave One-Out Cross Validation in different training-testing combinations. The best model predicted the OC with 6% and 13%deviation respect to the real value in one season by itself and when one season tested with another season, respectively. The use of clustering in estimation model is discussed.

As the global semiconductor market is growing steadily, the need for optimization of the man-ufacturing process is paramount. For example, in the process of transferring the semiconductor chips to the substrate, each chip needs to be individually separated from the dicing tape via a plunger. In this process, however, the fixed chip is not easily removed from the tape due to strong adhesion, and the chip can become damaged if it is forcibly pulled out. Therefore, the present paper reports the development of functional adhesive tapes that initially adhere strongly to the semi-conductor chip on the dicing tape but can be easily removed after transfer. The fabricated functional tape has an initial adhesion of 350 gf, which enables firm fixing of the semiconductor chip to be transferred, and a final adhesion of 0.8 gf after UV curing, thereby facilitating removal of the chip without damage after transfer. Therefore, the fabricated functional tape is expected to contribute to the optimization of the semiconductor manufacturing process and is expected to be useful in the semiconductor package manufacturing process.

Recently, considerable work has been directed at development of a ultra-compact X-ray free-electron laser based on emerging techniques in high field cryogenic acceleration, with attendant dramatic improvements in electron beam brightness, and state-of-the-art concepts in beam dynamics, magnetic undulators, and X-ray optics. A full conceptual design of a 1 nm XFEL with a length and cost over an order of magnitude below current XFELs has resulted from this effort. This instrument has been developed with an emphasis on permitting exploratory scientific research in a wide variety of fields in a university setting. Concurrently, compact FELs are being urgently developed for use as an instrument to enable next generation chip manufacturing through use as a high flux, few-nm lithography source. This new role suggests consideration of XFELs to addressed urgently emerging demands in this sector, as identified by recent national need studies, for new radiation sources aimed at chip manufacturing: a coherent hard X-ray source which enables frontier metrology methods. Indeed, it has been shown that one may use coherent X-rays to perform 10 nm-class resolution surveys of macroscopic, cm-scale structures such as chips, using ptychographic laminography. As the XFEL is a very promising candidate for realizing such methods, we present here an analysis of the issues and likely solutions associated with extending the UCXFEL to harder X-rays (above 7 keV), much higher fluxes and levels of coherence, and methods of applying such a source for ptychographic laminography to micro-electronic device measurements. We discuss the development path to move the concept to rapid realization of a transformative FEL-based application, outlining FEL and metrology system challenges.

Digital microfluidics (DMF) holds great potential for the alleviation of laboratory procedures in assisted reproductive technologies (ARTs). Electrowetting on dielectric (EWOD) provides dynamic culture conditions in vitro that may better mimic the natural embryo microenvironment. Thus far, EWOD microdevices have been proposed for in vitro gamete and embryo handling in mice and for analyzing the human embryo secretome. This article presents the development of the first microfluidic chip utilizing EWOD technology designed for the manipulation of bovine embryos in vitro. The prototype sustains the cell cycles of embryos manipulated individually on the chips during in vitro culture (IVC). Challenges related to the chip fabrication as well as to its application during bovine embryo IVC in accordance with the adapted on-chip protocol are thoroughly discussed, and future directions for DMF in ARTs are indicated.

The aim of this study is to provide a detailed strategy for Safe-by-Design (SbD) 3D printed lab-on-a-chip (LOC) device manufacturing, using Fused Filament Fabrication (FFF) technology. At first, the applicability of FFF in lab-on-a-chip device development is briefly discussed. Subsequently, a methodology to categorize, identify and implement SbD measures for FFF is suggested. Furthermore, the most crucial health risks involved in FFF processes are examined, placing the focus on the examination of ultrafine particle (UFP) and Volatile Organic Compound (VOC) emission hazards. Thus, a SbD scheme for lab-on-a-chip manufacturing is provided, while also taking into account process optimization for obtaining satisfactory printed LOC quality. This work can serve as a guideline for the effective application of FFF technology for lab-on-a-chip manufacturing through the safest applicable way, towards a continuous effort to support sustainable development of lab-on-a-chip devices through cost-effective means.