The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

In this paper, a new probe-fed wideband antenna with a circular patch and a coupled stacked ring is proposed. This antenna can be implemented by using suspended microstrip technique with total thickness of about 0.09 of center frequency wavelength. By using a novel feeding technique, in this antenna about 40 % reduction in area compared to similar works can be achieved. The obtained bandwidth in this antenna according to simulation results satisfying VSWR<2 is about 27.5 % from 5 to 6.6 GHz using two resonant frequencies. Also a comprehensive theoretical and parametric study is done in order to facilitate its designing in various frequency bands.

In this work, an novel flow-electric field coupling configuration for enhanced Zn-Cd cementation was designed and utilized. A series of tests were conducted to explore the optimization of Zn-Cd cementation process and its mechanism.Firstly, the various characterisations of the cadmium sponge at different locations in the device were compared and it was concluded that the purity of the cadmium sponge was optimal from the anode surface. The generation and stripping of cadmium sponge was revealed for the first time by cross-sectional electron microscopy. The four stages of the apparent reaction in the system were analysed in relation to the pH, cadmium concentration and cadmium sponge flaking at each flow rate. It was proved that the separation of cadmium sponge mainly occurred in the third phase. Secondly, by comparing the morphology and specific surface area of cadmium sheep at different flow rates, the optimum flow field velocity was identified as 30 ml/s. Six flow field configurations were compared and preferred. The results demonstrate that the LCAH modulation results in a more sparse structure of the cadmium sponge, which is more easily exfoliated from the zinc anode surface by fluid impact. This was considered to be the most beneficial flow field configuration for improving the cadmium cementation rate and reducing the cost of the reaction. Further, the reaction steps of the system were analysed. The diffusion process under different flow field configurations was confirmed by calculations to follow first order kinetics. The diffusion coefficient of LACH proved to be the highest in the comparative tests and this result was also supported by the apparent experimental results.

The circular economy is based on maintaining a circular flow of resources. Policymakers face difficulties in balancing national security and circular economy aspects in the field of mineral resources policy. With a uniquely expanded input-output table, this study estimates the final destination of several critical minerals (lithium, cobalt, yttrium, lanthanum, cerium, neodymium and dysprosium) and base metals (iron, copper and aluminum) in the Japanese economy for 2015. Our model shows quite a good similarity between the estimated composition and the actual data of products. The results reveal a detailed distribution of critical minerals and indicate prioritized implementation for creating and maintaining a circular flow of critical minerals. Developed decision flow guidance provides a comprehensive approach to national security and circular economy aspects for policymakers. For further actions, inclusive indicator development is required for policymakers to support the determination of implementation possibilities from social and technological aspects.

Among the best-known capillarity phenomena is a capillary rise, the understanding of which is essential in fluidics. Some capillary flows rise monotonically whereas others oscillate, but until now no criteria have been formulated for this scenario. In this paper, the Levine's capillary rise modelling is computed numerically, then the critical radius of the capillary tube is formulated by using the dimensional method and data fitting for identification of exponent index. The phase space diagram of capillary velocity versus height is obtained for the first time and shows that the phase transition from oscillating to monotonic rising happens when the phase trajectory decreases exponentially to somewhere other than the "attractor." Two general Maple codes of the problem are provided as an essential part of this paper.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Two modal decomposition techniques, including proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD), are used to identify the wake patterns past single and two crossing cylinders in 60° and 90° arrangements with gap ratio G = 4. The flow is simulated using direct numerical simulations (DNS) for Reynolds numbers Re = 100. The spatial scale of flow decreases with increasing modal frequency from the modal analysis. Two main modes are identified in the wake of the cylinders, namely spatially antisymmetric and symmetric modes. Antisymmetric and symmetric modes are related to cylinders’ vortex shedding and shedding vortices’ shift motion, respectively, whose frequencies are odd and even multiples of cylinders’ lift force frequency. In addition, a low-frequency mode concerning the shadowing effect of the downstream cylinder (DC) in 90° arrangement is found in the wake of the DC centre.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

Water reuse for irrigation is increasingly recognized as an essential and economical strategy in areas with water scarcity. A simple, low-cost, low-maintenance, and highly efficient Pond-In-Pond (PIP) treatment system can be used for wastewater reuse. PIP is a treatment technology in which two types of ponds -- anaerobic and aerobic -- are combined into a single pond and consist of a deeper inner section entirely submerged within the outer pond. Previous studies on PIPs and PIP-like systems have reinforced the potential for reuse through promising performance results with BOD removal over 80% and a reduction in land area requirements by approximately 40%. Yet, no prior efforts have been made to understand the performance mechanism of such systems. This study makes use of two, 2-D modeling tools in developing a fundamental understanding of PIP flow dynamics and the expected performance. The modeling results showed that the PIP configuration offers improved flow diversion along with reduced flow velocity. Additionally, the PIP retained approximately 17% more (p<0.05) particles than the traditional pond with most of the particles concentrated within the inner pond. Lower velocity and the higher solids retention in the PIP thus allowed for better treatment performance compared to traditional ponds. The findings from this study can be used as preliminary data for future in-depth investigations of the PIP system leading toward effective and optimal designs. This will help address the major societal concern of water scarcity with low-cost and effective wastewater treatment.

In chronic myeloid leukemia (CML), a clonal proliferative disorder of granulocytic lineage, the 90%‐95% of cases are characterized by t(9;22) (q34.1;q11.2) translocation, leading to the Philadelphia chromosome (1). Rarely, CML patients directly present a blast crisis, mostly of myeloid origin (2, 3). Herein, we describe one rare CML case, showing an unusual early T lymphoid blastic crisis.

The theory of water transport in trees, according to which the main driving force of water movement is the suction created by the evaporation of water by the meniscus (the curved surface of the capillary liquid column) on the evaporating elements, supported from below by root pressure, is flawed. The capillary effect in nature is around one meter. In the case of open-air gaps, the leaf cannot suck in the water against gravity because, in this case, the plant would not be sucking in water, but air through the open-air gap. If not, how do trees transport water? When evaporation occurs, there is no suction towards the canopy, but pressure is due to a reduction in the cross-section of the water pipe caused by heat loss through evaporation. At night, when evaporation stops, a thermal equilibration process is triggered, which restores the original cross-section of the pipe. This generates suction and draws water from the soil. As the hydrostatic pressure in the pipe is high for tall trees, the pipe is cut off. To prove my theory, I have given several examples. Water transport is not based on physical mechanical laws alone. There may be complex physiological, biochemical, and biophysical processes behind the operation of the pipe system.

Maker spaces can contribute significantly to the circular economy of cities: they demonstrate not only the economic potential of inner loop circularity, but also provide tangible evidence of spatial and social integration of production into the urban context. This paper presents findings from a typological analysis of 326 maker spaces in seven European cities, with a focus on selected exemplar case studies to reveal design characteristics, principles and opportunities for circular city development. The research shows that circular economy principles of ‘reduce-reuse-recyle’ are aligned with maker spaces such as repair cafés, secondhand shops and fab labs. In the context of cities, circularity is revealed by a spatial tightening of resource cycles that close the loops of product life cycles. Furthermore, urban maker spaces demonstrate social engagement and a relationship to local production which inherently includes maintenance, repair, reuse, and redistribution. This paper defines five maker typologies, presents exemplars of each from different urban contexts and posits hybrid design strategies for the transition to circular maker cities. Through the adoption of these findings into urban planning policy it is possible accelerate circular urban production and close the sustainability gap between small scale local and large scale regional manufacturing.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

In this paper, we provide alternative proofs to some results proposed in the article "New inequalities involving circular, inverse circular, hyperbolic, inverse hyperbolic and exponential functions" authored by Yogesh J. Bagul.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment ishigher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reduce surface runoff during rainy season.

Abstract: To describe the feeder topology and information exchange between intelligent electronic devices (IEDs) for Internet of Things (IoT), it is necessary to extend IEC 61850 and add a logical model. The feeder model described in IEC 61970 is then extended in IEC 61850 to serve as a container for the equipment along the distribution line. For the physical connections in the electrical equipment, both terminal and connectivity node logical models are added. Taking logical node XCBR as the example, its attributes for the terminals are added to the electrical equipment. The logical node LCNN is then further added in order to describe the connectivity node. By next adding the logical node LTPN to describe the topological node, and FTPA to describe the results of the topology analysis, we can efficiently describe the topology analysis results. Based on these new logical nodes, the exchange of topology information between intelligent terminals no longer relies on configuration files, but only requires logical nodes. Through the above expansion, the topology description and information exchange of medium and low voltage feeders are realized.

Abstract: Severe land degradation is the principal environmental problem in Ethiopian highlands in the form of soil erosion, and soil fertility loss, which is caused by human intervention for food, shelter, and energy demands. Soil erosion contributes to the loss of precious soil and water resources which are the basis of agricultural production and provide numerous other eco-system services. The Ethiopian highlands are one of the most degraded regions in the world. To combat such problems, the government of Ethiopia has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. Mount Yewel is one of the highlands in Northeastern Ethiopia where intensive soil and water conserva-tion has been implemented. Despite the massive investment in soil and water conservation measures, most of the rivers in the highlands of Ethiopia carry huge amounts of sediment with high flood risks in the wet season and streams are dried up in the dry period. Nonetheless, the impact of soil and water conservation measures on flood reduction and dry season flow en-hancement has not yet been quantified and evaluated. This research was then conducted on paired micro-catchments of Mount Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were col-lected from 22/11/2020 to 8/11/2022 on paired micro-catchments of Mount Yewel at their outlets and centers respectively. Base flow separation was done from the stream hydrograph using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software were employed for data analysis. Flow duration curves (FDC) for both watersheds were developed to compare the stream flow patterns between treated and untreated micro-catchments of Mount Yewel. The FDC indi-cated that the base flow from treated micro-catchment is higher and sustained in the dry season while it is low and unsustained in untreated micro-catchment. From statistical analysis, there is a significant (P

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

The effect of thermal radiation on the two – dimensional, steady-state, conjugate heat transfer from a circular cylinder with an internal heat source in steady laminar crossflow is investigated in this work. P₀ (Rosseland) and P₁ approximations were used to model the radiative transfer. The mathematical model equations were solved numerically. Qualitatively, P₀ and P₁ approximations show the same effect of thermal radiation on conjugate heat transfer; the increase in the radiation – conduction parameter decreases the cylinder surface temperature and increases the heat transfer rate. Quantitatively, there are significant differences between the results provided by the two approximations.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

An accurate assessment of the stage-discharge relationship in open channel flows is necessary and important to the design and management of hydraulic structures and engineering in practical hydrosystems such as rivers and streams. While the flow structures and patterns at open channel junctions are interesting and have been widely studied in the literature, this paper focuses further on the effect of flow junctions on stage-discharge relationship at mountain river confluences. In this study, both the flume and physical model experiments are designed and performed carefully to test and analyze the complex flow structures and characteristics at river confluences with different configurations and hydraulic conditions. The impacts of the flow junctions on the traditional stage-discharge relationship are analyzed in this study. The results of this study are discussed in the paper for the understanding of flow structures at flow junctions and the design and management of hydraulic structures in river engineering.

The high radio frequency polarization imaging of non-thermal emission from active galactic nuclei (AGN) is a direct way to probe the magnetic field strength and structure in the immediate vicinity of supermassive black holes (SMBHs) and is crucial in testing the jet-launching scenario. To explore the the magnetic field configuration at the base of jets in blazars, we took advantage of the full polarization capabilities of the GMVA (Global Millimeter VLBI Array). With an angular resolution of ~50 micro-arcseconds at 86 GHz, one could reach scales down to ~900 Schwarzschild radii (for a 10^9 solar mass black hole). We present here the preliminary results of our study on the blazar BL Lac. Our results imply that on sub-mas scales the core and central jet of BL Lac is significantly polarized with two distinct regions of polarized intensity. We also noted a great morphological similarity between the 7mm/3mm VLBI images at very similar angular resolution.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

Configuration techniques have been used in several fields, such as the design of business process models. Sometimes these models depend on the data dependencies, being easier to describe "what" has to be done instead of "how". Configuration models enable to use a declarative representation of business processes, deciding the most appropriate work-flow in each case. Unfortunately, data dependencies among the activities and how they can affect the correct execution of the process, has been overlooked in the declarative specifications and configurable systems found in the literature. In order to find the best process configuration for optimizing the execution time of processes according to data dependencies, we propose the use of Constraint Programming paradigm with the aim of obtaining an adaptable imperative model in function of the data dependencies of the activities described declarative.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

We construct a Bayesian estimator for the dilution of a wastewater sample. When wastewater is diluted by rainwater an estimate of the level of dilution is required if we are to normalise sample measurements of disease markers such as SARS-CoV-2 RNA. We consider the situation where flow measurements are available, but will regularly be unreliable because of the action of combined sewer outflows (CSOs) and wastewater storage tanks, which divert wastewater away from treatment plants when the flow is excessive. However, we also have proxies for the flow from various chemical markers (e.g.\ phosphate, ammonium, electrical conductivity), whose level per unit of population is fixed. The new flow estimator has multiple advantages compared to existing procedures: credible intervals for the estimates; optimal weighting of the chemical markers; systematic handling of missing and censored values; and model based smoothing without lags.

Iterated games, in which the same economic interaction is repeatedly played between the same agents, are an important framework for understanding the effectiveness of strategic choices over time. To date very little work has applied information theory to the information sets used by agents in order to decide what action to take next in such strategic situations. This article looks at the mutual information between previous game states and an agent's next action by introducing two new classes of games: ’invertible games’ and ‘cyclical games'. By explicitly expanding out the mutual information between past states and the next action we show under what circumstances these expressions can be simplified. These information measures are then applied to the Traveler's Dilemma game and the Prisoner's Dilemma game, the Prisoner's Dilemma being invertible, to illustrate their use. In the Prisoner's Dilemma a novel connection is made between the computational principles of logic gates and both the structure of games and the agents' decision strategies. This approach is applied to the cyclical game Matching Pennies to analyse the foundations of a behavioural ambiguity between two well studied strategies: ‘Tit-for-Tat' and ’Win-Stay, Lose-Switch'.

The construction industry is a resource and energy intensive industry and thus, has been criti-cized due to rising environmental concerns. As a result of that it has gained heightened interest in the concept of Circular Economy (CE) over the last decade to its ability to promote the slowing, reducing, and closing production and consumption cycles of materials and products used in the construction practices. Digital technologies hold potential to enhance the construction industry's ability to integrate the concept of CE in its practices. However, a clear understanding of digital technology (DT) related barriers that hinder practical implementation of CE, appears to be lacking within the sector. In light of this, this study aims to identify the barriers to adopting DTs to im-plement CE practices in the construction industry. To achieve this aim, a systematic literature review was conducted by reviewing twenty-three (23) relevant papers published until January 2024 in Scopus database. The VOS viewer software was used to perform a co-occurrence analysis of keywords to identify new and popular study areas in the field and content analysis was used to analyse the major barriers to adapt DTs to implement CE in the construction industry. The study identified thirty-four (34) barriers to use DTs to implement CE and these were categorized into nine areas such as: infrastructure, organizational, regulatory, standardization, investment, nature of the construction industry, technological, stakeholder and data related barriers. These findings will be beneficial for construction practitioners and policy makers to adopt DTs to integrate CE practices in the construction industry.

Skin and proximity effects have a considerable impact on current distribution in multi-strand cable lines. Under unfavorable heat exchange conditions some strands may be subject to excessive overheating, what may lead to serious malfunctions or even fires of the installation. The paper proposes a new criterion for a quick choice of spatial configurations, for which the effect might be minimized. A comprehensive analysis of literature cases is provided, including the recommendations of the U.S. National Code and the Canadian standard.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Australia has recently declared its commitment to a circular economy. Policy and initiatives to date have focused on recycling and waste management and research to date has highlighted the need for more ambitious policy, clearer definitions, collaboration, and consensus on goals. There are also calls from some government and non-business sectors for more inclusive circular models, including Doughnut Economics. In a context of competing mainstream circular economy and inclusive circular society discourses, circular intermediary organizations and their representatives are key to achieving change. Compared to the green growth business narrative of policy and industry media, intermediary representatives are aware of the diversity of challenges and solutions for Australia. Based on semi-structured interviews with twenty representatives of circular intermediaries in Australia and thematic discourse analysis, this study finds circular economy, circular society and de-growth discourses informing themes about government, business, growth, consumers, society, and policy present and future. The study concludes with recommendations for a more holistic policy and practice beyond the current circularity for circularity’s sake.

This study assessed the hydrological performance and runoff water quality of 12 green roof (GR) modular systems located at the Universidad de los Andes campus (Bogotá, Colombia). Based on 223 rainfall events spanning a 3-year period, average rainfall retention was 85% (SD = 25%). T-tests, Welch Test, multiple linear regressions and correlation analysis were performed in order to assess the potential effect of air temperature, substrate type, vegetation cover, relative humidity, antecedent dry weather period (ADWP), rainfall duration and rainfall maximum intensity. In some cases, GR design variables (i.e. growing media and type of vegetation) were found to be significant for describing rainfall retention efficiencies and, depending on the GR type, some hydrological variables were also correlated with the rainfall retention. Rainfall and GR runoff were monitored for Total Kjeldahl Nitrogen (TKN), Nitrates, Nitrites, Ammonia, Total Phosphorus (TP), Phosphates, pH, Total Dissolved Solids (TDS), Total Suspended Solids (TSS), Color, Turbidity, Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), Total Coliforms, metals and Poliaromatic Hydrocarbons (PAHs). The results obtained confirmed that GR systems have the ability to neutralize pH, but are source of the rest of the aforementioned parameters, excluding PAHs (with concentrations below detection limits), Ammonia, TSS, Se and Li, where differences with reference values (rainfall and plastic panel runoff) were not statistically significant. Substrate type, event size and rainfall regime are relevant variables for explaining runoff water quality.

From the aerial parts of Salvia ballotiflora, eleven diterpenoids were isolated, among them, four icetexanes, and one abietane (1–5), which are first reported. Their structures were established by spectroscopic means, mainly ¹H and ¹³C NMR, including 1D and 2D homo- and hetero-nuclear experiments. Most of the isolated diterpenoids were tested for their antiproliferative, anti-inflammatory, and radical scavenging activities using the sulforhodamine B assay on six cancer cell lines, the TPA induced ear edema test in mice, and the reduction of the DPPH assay, respectively. Some diterpenoids showed anti-proliferative activity, these being icetexanes 6 and 3, which were the most active with IC₅₀ (µM) = 0.27 ± 0.08 and 1.40 ± 0.03, respectively, for U251 (human glioblastoma) and IC₅₀ (µM) = 0.0.46 ± 0.05, and 0.82 ± 0.06 for SKLU-1 (human lung adenocarcinoma), when compared with adriamycin (IC₅₀ (µM) = 0.08 ± 0.003, and 0.05 ± 0.003, as the positive control, respectively. Compounds 3 and 10 showed significant reduction of the induced ear edema of 37.4 ± 2.8 and 25.4 ± 3.0% (at 1.0 µmol/ear), respectively. Compound 4 was the sole active diterpenoid in the antioxidant assay (IC₅₀ = 98. 4 ± 3.3), using α-tocopherol as positive control, IC₅₀ (µM) = 31.7 ± 1.04. The diterpenoid profile found is of chemotaxonomic relevance and reinforces the evolutionary link of S. ballotiflora with other members of the section Tomentellae.

Acute and chronic graft versus host disease (a/cGVHD) are major complications of allogeneic stem cell transplantation and a frequent cause of non relapse-mortality. The treatment of a/cGVHD consists of steroid administration at full dose. In the case of aGVHD, around 60 % of patients with grade III/IV fails to respond (steroid-resistant, SR), requiring a second line therapy. Extracorporeal photopheresis (ECP) represents a good option for second line treatment, leading to multiorgan response in several patients. Here, we have evaluated the performances of a cytofluorimetric quality control of the first ECP procedure in 29 patients with severe SR aGVHD who underwent ECP. The quality control represents a check control of in vitro cell apoptosis/death induction in collected and irradiated CD3+ cells by ECP. Our analysis shows that in more than 70 % quality controls a relevant apoptotosis/death of CD3+ cells was observed after cell irradiation, as compared to non-irradiated controls. Albeit observed in a small patients’ series, the occurrence of relevant in vitro effect after ECP relates to less procedures and/or to a better survival on ECP. Age, disease, gender, aGVHD grade and time from transplant to the first ECP had not impact on ECP efficacy in this patients’ series.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.

Magneto-optic surface plasmon resonance (MOSPR) based sensors are highly attractive as next generation biosensors. However, these sensors suffer from oxidation leading to degradation of performance, reproducibility of the sensor surface because of the difficulty of removing adsorbed materials, and degradation of sensor surface during surface cleaning, and these limit their applications. In this paper, I propose MOSPR-based biosensors with 0 to 15 nm thick inert polycarbonate laminate plastic as a protective layer and theoretically demonstrate the practicability of our approach in water-medium for three different probing samples: ethanol, propanol, and pentanol. I also investigate microstructure and magnetic properties. The chemical composition and layered information of the sensor are investigated using X-ray reflectivity and X-ray diffraction analyses and these show distinct fcc-Au (111) phases, as dominated by the higher density of conduction electrons in Au as compared to Co. The magnetic characterization measured with the in-plane magnetic field to the sensor surface for both the as-deposited and annealed multilayers showed isotropic easy axis magnetization parallel to the multilayer interface at a saturating magnetic field of <100 Oe. The sensor showed a maximum sensitivity of 5.5 × 10⁴%/RIU for water-ethanol media and the highest detection level of 2.5 × 10⁻⁸ for water-pentanol media as the protective layer is increased from 0 to 15 nm.c

The purpose of this study is to investigate the moderating effect of technology configuration capability on the relationship between strategic flexibility and organizational performance through different stages of technological life cycle. Through the empirical research on the 439 Chinese high-tech organizations, it shows that a technological configuration capability has enhanced the effect of strategic flexibility to the organizational performance in the complex dynamic environment. However, the impact on the different stages of technological life cycle is different. In addition, this paper explored strategic flexibility on different stages of technological life cycle on the basis of empirical study.

In this work, generalized geometry of second-order tangent groups and affine configuration complexes is proposed. Initially, geometry for higher weights n=4 and weights n=5 is presented through some interesting and suitable homomorphisms, finally, this geometry is extended and generalized for any weight n.

This paper outlines our effort on optimizing Pulsed Magneto-Oscillation (PMO) design in order to improve the efficiency of ingot manufacturing under PMO. Our calculation and experiment provided optimized PMO coil design and special configuration. Our optimized PMO design offered us a device that enabled the operator to examine and operate the melt without losing the efficiency. In one of the designs, the equipment even refined the grain sizes. Our work also showed an optimized distance range between the coil and the melt surface that maximized the refinement effects.

Scedosporium species are human pathogenic fungi, responsible for chronic, localised, and life-threatening disseminated infections in both immunocompetent and immunocompromised individuals. Diagnosis of Scedosporium infections currently relies on non-specific CT, lengthy and insensitive culture from invasive biopsy, and time-consuming histopathology of tissue samples. At present, there are no rapid antigen tests that detect Scedosporium-specific biomarkers. Here we report the development of a rapid (30 min) and sensitive (pmol/L sensitivity) lateral-flow device (LFD) test, incorporating a Scedosporium-specific IgG1 monoclonal antibody (mAb), HG12, which binds to extracellular polysaccharide (EPS) antigens of between ~15 kDa and 250 kDa secreted during hyphal growth of the pathogens. The test is compatible with human serum, and allows the detection of the Scedosporium species most-frequently reported as agents of human disease (Scedosporium apiospermum, Scedosporium aurantiacum, and Scedosporium boydii), with limits of detection (LOD) of the EPS biomarkers in human serum of ~0.81 ng/mL (S. apiospermum), ~0.94 ng/mL (S. aurantiacum), and ~1.95 ng/mL (S. boydii). The Scedosporium-specific LFD (ScedLFD) test therefore provides a potential novel opportunity for the detection of infections caused by different Scedosporium species.

The purpose of this paper is twofold. First, we introduce a geometric approach to study the circular orbit of a particle in static and spherically symmetric spacetime based on Jacobi metric. Second, we apply the circular orbit to study the weak gravitational deflection of null and time-like particles based on Gauss-Bonnet theorem. By this way, we obtain an expression of deflection angle and extend the study of deflection angle to asymptotically non-flat black hole spacetimes. Some black holes as lens are considered such as a static and spherically symmetric black hole in the conformal Weyl gravity and a Schwarzschild-like black hole in bumblebee gravity. Our results are consistent with the previous literature. In particular, we find that the connection between Gaussian curvature and the radius of a circular orbit greatly simplifies the calculation.

Plastics have become an important environmental concern due to their durability and resistance to degradation. Out of all plastic materials, polyesters such as polyethylene terephthalate (PET) are amenable to biological degradation due to the action of microbial polyester hydrolases. The hydrolysis products obtained from PET can thereby be used for the synthesis of novel PET as well as becoming a potential carbon source for microorganisms. In addition, microorganisms and biomass can be used for the synthesis of the constituent monomers of PET from renewable sources. The combination of both biodegradation and biosynthesis would enable a completely circular bio-PET economy beyond the conventional recycling processes. Circular strategies like this could contribute to significantly decrease the environmental impact of our dependence on this polymer. Here we review the efforts made towards turning PET into a viable feedstock for microbial transformations. We highlight current bottlenecks in the degradation of the polymer and the metabolism of the monomers and we showcase fully biological or semisynthetic processes leading to the synthesis of PET from sustainable substrates.

Driven by the rapid uptake of battery electric vehicles, Li-ion power batteries are increasingly reused in stationary energy storage systems, and eventually recycled to recover all the valued components. Offering an updated global perspective, this study provides a circular economy insight on lithium-ion battery reuse and recycling.

Background: Early postoperative airway management after laryngo-tracheal surgery is crucial. Acute respiratory failure due to glottis’ oedema may occur, requiring reintubation. This can prolong ventilatory assistance, jeopardizing the anastomosis. To date, only judicious steroid administration and fluid management are available to avoid more invasive procedures. High-Flow-Oxygen-Therapy(HFOT) is a noninvasive O2 support method providing humidification, warmed air, Positive-End-Expiratory-Pressure(AIRVO2). No data exist about HFOT use to prevent early complications after laryngo-tracheal surgery. Methods: Between Sept.2020-Sept.2022, 107 consecutive patients underwent laryngo-tracheal surgery received HFOT(Group A). Data and long-term results were compared with those of 80 patients operated between Sept.2018-Aug.2020(Group B), when HFOT was not available. All patients were operated in a single center. No pre- or post-operative settings changed, except for HFOT introduction. We analyzed and compared the risk for “delayed” reintubation (unexpected reintubation within the first 24-48 hours after extubating/laryngeal mask removal) in the two groups. Results: No patients reported HFOT-related adverse events. Control group(B) presented “delayed” reintubation in 37% (p= 0.027), Intensive Care Unit admission in 67%(p=0.005) and longer hospital stay(p=0.001) compared to HFOT group(A). Minor complications rate was 3% in both group and overall mortality was 0%. Re-stenosis was described in 4.6% of HFOT group, without a statistically significant difference (p=0.7006). Conclusions: Our study is the first to investigate HFOT use in patients undergoing laryngo-tracheal surgery, potentially representing a consistent innovation in the peri-operative management of these patients. With the limit of a retrospective series, we would suggest HFOT use for preventing post-operative reintubation rate, possibly reducing ICU admission and hospital stay.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

The paper delves into an extensive exploration of the integration of the circular economy paradigm within the realm of additive manufacturing (AM). The objective is to comprehensively investigate existing methodologies for structuring the symbiotic relationship between circular economy and additive manufacturing, while meticulously analyzing the current research gap concerning the implementation of circular economy principles in additive manufacturing practices. A thorough review focusing on the sustainability of additive manufacturing within the circular economy framework was conducted. This review aims to recognize and delineate pertinent aspects related to post-use material valuation in AM, recyclability of materials, and the environmental footprint associated with these processes. Emphasis was placed on the significance of examining circular economy facets concerning additive manufacturing processes to establish a holistic understanding. The overarching goal of this review is to augment knowledge regarding the potential advantages and benefits derived from the seamless integration of circular economy principles within AM. By elucidating the activities essential to attain compliance with the Sustainable Development Goals, this study endeavors to illuminate the pathway toward promoting sustainable development through the harmonious marriage of additive manufacturing and the circular economy.

It was thought until the 1990s that the eukaryotic translation machinery was unable to translate a circular RNA. However internal ribosome entry sites (IRESs) and m⁶A-induced ribosome engagement sites (MIRESs) were discovered, promoting 5’end-independent translation initiation. Today a new family of so-called “non-coding” circular RNAs (circRNAs) has emerged, revealing the pivotal role of 5’end-independent translation. CircRNAs have a strong impact on translational control via their sponge function, and form a new mRNA family as they are translated into proteins with pathophysiological roles. While there is no more doubt about translation of covalently closed circRNA, the linearity of canonical mRNA is only theoretical: it has been shown for more than thirty years that polysomes exhibit a circular form and mRNA functional circularization has been demonstrated in the 1990s by the interaction of initiation factor eIF4G with poly(A) binding protein. More recently, additional mechanisms of 3’-5’ interaction have been reported, including m⁶A modification. Functional circularization enhances translation via ribosome recycling and acceleration of the translation initiation rate. This update of covalently and non-covalently circular mRNA translation landscape shows that RNA circular shape might be the rule for translation with an important impact on disease development and biotechnological applications.

There is an increasing trend that Unmanned Combat Air Vehicles (UCAVs) are employed to complete different combat missions in modern wars. This paper investigates a UCAV routing problem, which simultaneously considers the decisions for the configuration of weapons carried by the UCAV subject to its capacity and the allocation of weapons to the targets subject to their destroying requirements. An integer linear programming model is developed to formulate the problem. An adaptive large neighborhood search (ALNS) heuristic is proposed to solve the problem, in which seven neighborhood structures are designed and employed. Randomly generated instances covering the small, medium and large sizes are used to test the proposed ALNS algorithm. CPLEX is also utilized to solve the small-size instances, whose results are compared with that obtained by the ALNS algorithm. And the extensive experimental results confirm the effectiveness and superiority of the proposed ALNS algorithm.

We monitored the water quality and hydrological conditions of a horizontal subsurface constructed wetland (HSSF-CW) in Beijing, China, for 2 years. We simulated the area rate constant and the temperature coefficient with the first-order kinetic model. We examined the relationships between the nitrogen (N) removal rate, N load, seasonal variations in the N removal rate, and environmental factors, such as the area rate constant, temperature, and dissolved oxygen (DO). The effluent ammonia (NH₄⁺-N) and nitrate (NO₃⁻-N) concentrations were significantly lower than the influent concentrations (p<0.01, n=38). The NO₃⁻-N load was significantly correlated with the removal rate (R²=0.9566, p<0.01), but the NH^₄+-N load was not correlated with the removal rate (R²=0.0187, p>0.01). The area rate constants of NO₃⁻-N and NH₄⁺-N at 20 °C were 27.01±26.49 and 16.63±10.58 m∙yr⁻¹, respectively. The temperature coefficients for NO₃⁻-N and NH₄⁺-N were estimated at 1.0042 and 0.9604, respectively. The area rate constants for NO₃⁻-N and NH₄⁺-N were not correlated with temperature (p>0.01). The NO₃⁻-N area rate constant was correlated with the corresponding load (R²=0.9625, p<0.01). The NH₄⁺-N area rate was correlated with DO (R²=0.6922, p<0.01), suggesting that the factors that influenced the N removal rate in this wetland met Liebig's law of the minimum.

Glycerol represents a useful functional component of heat-transfer fluids. Glycerol is known to be triboelectrically active. We report how the flow of glycerol, stopped in a cylindrical coiled pipe, influences horseradish peroxidase (HRP) enzyme. Namely, glycerol flow was pumped through the coil and then stopped. After that, we incubated the 0.1 µM solution of HRP near the side of the coil, and then adsorbed HRP onto mica. This operation markedly increased the HRP aggregation on mica in comparison with the control sample. We explain this phenomenon by the influence of triboelectrically induced electromagnetic fields. Our results can be useful in the development of flow-based systems for biosensors and bioreactors.

This work examines the beneficial role of an unsteady stenosis, operating without the use of any external energy source, as a means for augmenting the flow rate of a valveless pump in a hydraulic loop, including an open tank. In contrast to our previous work that the loop was horizontal, here gravity was taken into account. The stenosis neck cross-sectional area was controlled by the fluid pressure and an opposing force applied externally by a spring of adjustable tension. The pincher compressed and decompressed periodically a part of a flexible tube with frequencies from 5 Hz to 11 Hz and compression ratios Ab from 24% to 65%. The presence of the stenosis increased the net flow rate 19 times for Ab = 24%, and 6.3 times for Ab = 38%, whereas for Ab = 65%, the flow rates were comparable. The volumetric efficiency varied from 30% to 40% under the presence of the stenosis, and from 2% to 20% without the stenosis. The role of the stenosis role was to cause a unidirectional flow, opening during tube compression and closing during decompression. The pressure amplitudes along the flexible tube increased towards the rigid-flexible tube junction (as a result of the wave reflections) which were found to be significantly attenuated by the presence of the stenosis.

The standard edge crush test (ECT) allows to determine the crushing strength of the corrugated cardboard. Unfortunately, this test cannot be used to estimate the compressive stiffness, which is an equally important parameter. It is because, any attempt to determine this parameter using current lab equipment quickly ends in a fiasco. The biggest obstacle is obtaining a reliable measurement of displacements and strains in the corrugated cardboard sample. In this paper, we present a method that not only allows to reliably identify the stiffness in the loaded direction of orthotropy in the corrugated board sample, but also the full orthotropic material stiffness matrix. The proposed method uses two samples: (a) traditional, cut crosswise to the wave direction of the corrugated core, and (b) cut at an angle of 45 degrees. Additionally, in both cases, an optical system with digital image correlation (DIC) is used to measure the displacements and strains on the outer surface of samples. The use of a non-contact measuring system allows to avoid using the measurement of displacements from the crosshead, which is burdened with a large error. Apart from the new experimental configuration, the article also proposes a simple algorithm to quickly characterize all sought stiffness parameters. The obtained results are finally compared with the results obtained in the homogenization procedure of the cross-section of the corrugated board. The results were consistent in both cases.

Project portfolio configuration (PPC) is an important approach to maintain the sustainable development of enterprises and achieve organizations’ strategy. However, the synergetic efficacy of PPC which determines the degree of the project's strategic objectives achieved is a fuzzy problem and hard to be measured. To solve this problem, this paper takes the data envelopment analysis (DEA) as the tool to measure the efficacy of PPC under deterministic conditions. First, a portfolio evaluation index system which takes financial indicators and non-financial indicators into consideration is developed based on the review of the literature; Second, an evaluation model based on DEA is built to reduce the number of decision making-unit with the perspective of synergetic theory; Then, a computational experiment is studied to verify the feasibility of this proposed model. The results of this computational experiment show that this model can effectively narrow scope of decision-making, improve the decision-making level and provide a reference to decide the DEA effective project portfolio decision-making unit. To our knowledge, this study is the first time to apply the notion of synergetic efficacy and DEA to the PPC domain. It is hoped that this paper may shed lights on any further study about PPC and enterprise competitiveness of sustainable development.

In the paper the experimental methodology for the single-crystal circular plate deformation measurement and subsequent procedure for mechanical properties quantitation are developed. The procedure is based on a new numerical-analytical solution of nonlinear boundary-value problem for finite deformations of a circular anisotropic plate. Using the developed method, a study of the deformation of single-crystal circular plates formed on the basis of a silicon-on-insulator structure was carried out. The values of residual stresses are determined and it is shown that the presence of these stresses increases the flexural rigidity of the plate in several times.

Serotonin (5-HT) show important relations to stress, and this relationship is crucial to understanding the psychobiology of common mental disorders. Environmental stressors regulate phasic and tonic serotonin levels, which are related to valence and outcome probabilities. This regulation takes place at smaller timescales, but also at the level of gene expression regulation. Moreover, genes related to the synthesis, metabolism, and transport of 5-HT are also involved in this regulation. Genetic variations in these genes modulate how stressors can lead to mental distress, but stressors also modulate gene expression in a genotype-dependent manner. As a result, the relationship between psychosocial stress and the regulation of the expression of 5-HTergic genes is bidirectional. This suggests a “circular causality” in which gene variations control tonic and phasic 5-HT signals (“upward causality”), while configurations and functions of the entire organism determine which genes are up- or downregulated, or which gene products are actually relevant in each situation (“downward causality”). The highly important role of social factors in human psychopathology is highlighted, and factors such as attachment and socioeconomic status modulate how the circular vertical causality between genes, neurotransmitters, and behavior is organized, representing circular horizontal causality. These complex interrelationships also suggest that more refined epistemologies are needed to fully grasp the relationship between 5-HT and common mental disorders.

The formulation used by most of the studies on an elastic torus are either Reissner mixed formulation or Novozhilov's complex-form one, however, for vibration and some displacement boundary related problem of a torus, those formulations face a great challenge. It is highly demanded to have a displacement-type formulation for the torus. In this paper, I will carry on my previous work [ B.H. Sun, Closed-form solution of axisymmetric slender elastic toroidal shells. J. of Engineering Mechanics, 136 (2010) 1281-1288.], and with the help of my own maple code, I am able to simulate some typical problems and free vibration of the torus. The numerical results are verified by both finite element analysis and H. Reissner's formulation. My investigations show that both deformation and stress response of an elastic torus are sensitive to the radius ratio, and suggest that the analysis of a torus should be done by using the bending theory of a shell, and also reveal that the inner torus is stronger than outer torus due to the property of their Gaussian curvature. Regarding the free vibration of a torus, our analysis indicates that both initial in u and w direction must be included otherwise will cause big errors in eigenfrequency. One of the most intestine discovery is that the crowns of a torus are the turning point of the Gaussian curvature at the crown where the mechanics' response of inner and outer torus is almost separated.

Two heating surfaces with longitudinal fins are located within the closed channel inside the housing made of thermal insulation material. The air flow inside the channel was carried out by an axial fan. The heating of the fins is established by using two positive temperature coefficient heating elements (PTC). Air flows circularly from one finned surface to another, and after reaching the required temperature, it leaves the housing. In the heating system conceived in this way, a methodology based on transient thermal irreversibility of heating sources and circular air flow has been established. Volumetric air flow and circulation time within the channel were varied. The total entropy generated does not include hydraulic irreversibility, but transient thermal irreversibility of the air and heat sources. For conducting analytical modeling, the temperature of the PTC heater was considered constant at 423K and 473K. Volumetric air flow varied in the interval from 0.00001m3s-1 to 0.00006m3s-1. The experimental determination of the transient thermal entropy was performed at a much higher air flow rate of 0.005m3s-1 inside the closed channel. Due to the continuous increase in air temperature, the temperatures of both PTC heaters increased within the examined time interval of 300s. According to experimental testing, the total transient thermal entropy of the described heating system has a minimum after 175s from the start of the circular heating of the air. The minimum of transient entropy also implies the optimal time of channel opening and exit of heated air.

The Circular Economy of plastics is a promising concept that has the potential to reduce pollution and close the loop on plastic waste. However, further research is needed to develop more efficient and environmentally friendly methods of recycling plastic. This review article discusses the Circular Economy of plastics, its potential benefits and drawbacks, and the challenges that need to be addressed to make it a reality. Some case studies are also examined to explore how the Circular Economy of plastics has been implemented across the globe.

The move towards a new Circular Economy (CE) economic model has been advocated and supported in Portugal, however, there is limited research on this topic. To address this gap, a quantitative research based on an online survey was carried out among 99 Portuguese organizations, encompassing a wide range of sectors and sizes. The results show that CE is regarded as a strategic and relevant issue for profitability and value creation. Furthermore, the perception that it requires the adoption of new business models in addition to the classical “reduce, reuse, and recycle” approach is growing. Moreover, based on the hypotheses raised, results suggest that the level of CE adoption is positively impacted by the status of the EMS (Environmental Management System) certification and the willingness to improve the environmental performance and achieve a sustainable business model. However, CE activities are still relatively modest and a friendlier context (fiscal, legal, organizational, etc.) and the stronger support from supply chain agents and consumers are required. Future research should focus on how to design and shape the transition from a linear to a CE economy, and to ascertain if the positive attitude towards CE is materialized in changing the way business is done.

Kinematic control of redundant serial manipulators has been carried out for the past half century based primarily on a generalized inverse velocity formulation that is known to have mathematical deficiencies. A recently developed inverse kinematic position mapping is extended to an operational configuration space differentiable manifold formulation for kinematic control with obstacle avoidance is employed to resolve deficiencies in the generalized inverse velocity formulation. Output trajectory tracking with obstacle avoidance for four and twenty degree of redundancy manipulators is carried out to demonstrate the effectiveness of the differentiable manifold approach and that it resolves deficiencies of the conventional generalized inverse velocity formulation.

Background: Formation and rupture of cerebral aneurysms may be related to certain types of configuration of the circle of Willis. Analysis of their interdependence can be of great importance. Methods: A group of 114 patients treated operatively for the cerebral aneurysm rupture and a group of 56 autopsied subjects were involved in the study. Four basic types of the circle of Willis configurations were formed–two symmetric types A and C, and two asymmetric types B and D. Results: A statistically significantly higher presence of asymmetry of the circle of Willis in the group of surgically treated subjects (p=0.006) with a significant presence of asymmetric Type B in this group (p=0.017) were determined. The presence of changes in the A1 segment in the group of subjects with solitary aneurysms on the anterior communicating artery showed a statistically significant presence in the group of autopsied subjects (p=0.0004). Analyzing the presence of symmetry of the circle of Willis between the two groups, that is, the total presence of symmetric types A and C indicated their statistically significant presence in the group of autopsied patients (p=0.043). Conclusion: Changes such as hypoplasia or aplasia of A1 and the resulting asymmetry of the circle of Willis directly affect the possibility of the rupture of cerebral aneurysms. Detection of the corresponding types of the circle of Willis after diagnostic examination can be the basis for the development of a protocol for monitoring such patients.

This paper introduces a sliding mode control (SMC) based equivalent control method to a novel high output gain Cuk converter. An additional inductor and capacitor improves the efficiency and output gain of the classical Cuk converter. Classical PI controllers are widely used in DC-DC converters. However, it is a very challenging task to design a single PI controller operating in different load and disturbances. SMC based equivalent control method which achieves a robust operation in a wide operation range is also proposed. Switching frequency is kept constant in appropriate interval in different loading and disturbance conditions by implementing a dynamic hysteresis control method. Numerical simulations conducted on Matlab/Simulink confirm the accuracy of analytical analysis of high output gain modified Cuk converter. In addition, proposed equivalent control method is validated in different perturbations to demonstrate the robust operation in wide operation range.

Non steady applied magnetic field impact on a liquid metals has good prospects for industry. For a better understanding of heat and mass transfer processes under these circumstances, numerical simulations are needed. A combination of finite elements and volumes methods was used to calculate the flow and solidification of liquid metal under electromagnetic influence. Validation of numerical results was carried out by means of measuring with ultrasound Doppler velocimetry technique, as well as with neutron radiography snapshots of the position and shape of the solid/liquid interface. As a result of the first part of the work, a numerical model of electromagnetic stirring and solidification was developed and validated. This model could be an effective tool for analyzing the electromagnetic stirring during the solidification process. In the second part, the dependences of the velocity pulsation amplitude and the melt velocity maximum value on the magnetic field pulsation frequency are obtained. It was found numerically the ability of the pulsating force action to develop higher values of the liquid metal velocity at a frequency close to the MHD resonance. Obtained characteristics give a more detailed description of the electrically conductive liquid behaviour under action of pulsating traveling magnetic field.

The circular economy (CE) has emerged as a viable alternative for tackling the problems caused by rising consumption, including solid waste (SW). The present study conducted a meta-analysis of research published between 2012 and 2022 on CE and solid waste management (SWM). A bibliometric analysis was used from the Web of Science (WoS) and Scopus databases. By studying the articles, we briefly discussed the connections between them and how one contributes to the evolution of the other. Some findings point to greater collaboration between Italy and Bolivia, followed by China and Malaysia. However, they move away from the traditional axes as the United States and Canada. In addition, it was found that the adoption of reuse and selective collection, in fact, allow the reduction of the volume of discarded materials. In this way, it was possible to conclude that a greater connection between CE and GRS makes it possible to optimize the useful life of landfills through the treatment of organic waste and recycling, to encourage waste picker cooperatives and selective collection programs, and to reduce the financial costs of the system as a whole, making it more durable and sustainable.

In order to properly cover different scenarios, radiation patterns of antennas should be accordingly adjusted before fabrication. However, most antennas are unable to provide both broadside beam and designable conical beam which are usually-used radiation patterns for radio coverage. In this paper, a planar Circular Polarized (CP) annular Leaky-Wave Antenna (LWA) with conical beam is proposed, which is realized on annular Substrate-Integrated Waveguide (SIW). Broadside beam or conical beam could be easily obtained by fabricating the LWA with modified structural parameters. The central operating band is 5.8 GHz. The LWA allows only the -1th spatial harmonic to radiate, while the fundamental wave and other spatial harmonics are suppressed in slow wave mode. In order to validate the design effectiveness, two examples for broadside beam and conical beam radiation are fabricated and measured. The measurement results show good agreement with the simulation results. The proposed LWA presents a promising radiation performance and is a good candidate for wireless communication applications.

An effective approach to fabricate large-scale of conducting polyaniline (PANI) by an in situ anodic electrochemical polymerization on the nickel foam, which coated by a novel aryl diazonium salt (ADS)-functionalized graphene (ADS-G). In present work, ADS-G was used as a high surface area support material for electrochemical polymerization of PANI. Electrochemical performances of the ADS-G/PANI composites exhibited better suitability as supercapacitor electrode materials than that of the PANI. The ADS-G/PANI composites achieved the specific capacitance of 528 F g-1, which was higher than that of PANI (266 F g-1) due to the excellent electrode-electrolyte interaction and synergistic effect of electrical conductivity between ADS-G and PANI in the composites. These findings suggested that the ADS-G/PANI composites were a suitable composite for the potential supercapacitor applications.

Due to increased energy intensive human activities resulting accelerated demand for electric power coupled with occurrence of natural disasters with increased frequency, intensity, and duration, it becomes essential to explore and advance renewable energy technology for sustainability of the society. Addressing the stated problem and providing a radical solution has been attempted in this study. To harvest the renewable energy, among variety of solar cells reported, a composite a-Si/CZTS photovoltaic devices has not yet been investigated. The calculated parameters for solar cell based on the new array of layers consisting of a-Si/CZTS are reported in this study. The variation of i) solar cell efficiency as a function of CZTS layer thickness, temperature, acceptor, and donor defect concentration; ii) variation of the open circuit current density as a function of temperature, open circuit voltage; iii) variation of open circuit voltage as a function of the thickness of the CZTS layer has been determined. There has been no reported study on a-Si/CZTS configuration-based solar cell, analysis of the parameters, and study to address the challenges imped efficiency of the photovoltaic device and the same has been discussed in this work. The value of the SnO2/a-Si/CZTS solar cells obtained from the simulation is 23.9 %.

This paper reports design of a 2 × 4 hybrid multimode interferometer-Mach-zehnder interferometer (MMI-MZI) configuration and compact thermo-optical switch consisting of slab waveguides on the silicon-on-insulator (SOI), platform. The device consisted of two identical MMIs as power splitters and couplers that are connected with two identical MMI-based phase shifters, and linear tapers at both ends of the MMIs to minimize the power coupling loss. A thin Al pad is used as a heating element, and a trench is created around this pad to prevent heat from spreading and to minimize loss. The calculated average thermo-optical switching power consumption, excess loss, and power imbalance are 1.4 mW, 0.9 dB, and 0.1 dB, respectively. The overall footprint of the device is 6 × 304 μm². The new heating method has advantages of compact size, ease of fabrication on SOI platform with the current CMOS technology, and offers low excess loss and power consumption as demanded by devices based on SOI technology. The device can act as two independent optical switches in one structure.

India has pledged ambitious initiatives to mitigate its growing economies’ impact on the climate, including a goal of net zero emissions by 2070. The transportation sector is one of the key sources of emissions. Therefore, fostering e-mobility within this sector is a key priority for the Indian government. The lifecycle of LiBs raises numerous concerns regarding its sustainability in production, use of rare materials, and most importantly waste management. Furthermore, this paper will highlight the case for EV battery recycling as a growing sector that also has the potential to foster circularity in the EV sector. Through the introductory section, this paper lays out rationale for battery recycling in a circular EV economy. The subsequent sections discuss the current and emerging battery technologies and their link to recycling methods whilst overviewing domestic and foreign battery recycling companies. Finally, the paper concludes with a gap assessment of the battery recycling ecosystem in India and makes recommendations to further integrate this industry into the EV supply chain. As India steers towards a sustainable future, it is imperative that the country integrates battery recycling to enhance circularity in the EV ecosystem, closing the gap between a growing number of EVs and waste management.

The circular economy is an alternative paradigm whose purpose is the protection of the environment, the prevention of pollution and the growth of economic prosperity. This paper covers research which is qualitative in nature but has an exploratory scope through a documentary review, and includes proposals to promote sustainability. A more responsible consumption or use can be achieved by educating the user or consumer to return the product to production or repair through a collection service by way of reverse logistics (recovery of materials), followed by recycling or reuse of the product or its components to then offer these as recovered or recycled products on the market.

Fish oil rich in polyunsaturated omega-3 fatty acids is extracted in high yield from anchovy filleting waste using d-limonene as green biosolvent in a simple solid-liquid extraction performed by mechanically stirring and maceration followed by limonene removal via evaporation under reduced pressure. As limonene is renewably obtained from waste orange peel, this protocol establishes a circular bioeconomy method to obtain valued omega-3 extracts from biowaste available worldwide in several million t/year amount. The method closes the materials cycle and opens the route to full valorisation of an important biological resource so far mostly discarded as waste. Significant economic opportunities benefiting local communities, the ecosystem and public health are anticipated.

In this paper, a new millimeter wave 3D imaging radar is proposed. The user just needs to move the radar along a circular track, a high resolution 3D imaging can be generated. The proposed radar uses the movement of itself to synthesize a large aperture in both the azimuth and elevation directions. It can utilize inverse Radon transform to resolve 3D imaging. To improve the sensing result, compressed sensing approach is further investigated. The simulation and experimental result further illustrated the design. Because a single transceiver circuit is needed, a light, affordable and high resolution 3D mmWave imaging radar is illustrated in the paper.

The textile and clothing (T&C) industry is not usually viewed as an exemplar of sustainable de-velopment and the circular economy, as the industry has hitherto made its products in linear fashion, with relatively little recycling of the finished goods. This article examines the industry’s approach to the core sustainability concept and the circular economy in particular, through a re-view of the available academic literature, evidence from corporate sustainability reports and websites, and feedback from an online survey of industry professionals. The role of digital technology deployment in engendering sustainability and the circular economy in the industry is also explored. The study finds that whilst sustainability is now firmly embedded at the strategic level in the vast majority of companies studied, attitudes towards the circular economy remain fickle. The use of digital technologies in support of sustainability objectives is also limited at present, but the article concludes that the need to meet compliance requirements and new cus-tomer perceptions of sustainability will speed the transition to circular economy activities, facili-tated by greater exploitation of digital technologies. Building upon the research findings, existing models and an initial conceptual framework, a simple operational model for initiating such a transition for small-to-medium sized enterprises in the T&C industry is put forward.

In today’s fast paced, attention-demanding society, executive functions and attentional resources are often taxed. Individuals need ways to sustain and restore these resources. We first review the concepts of attention and restoration, as instantiated in Attention Restoration Theory (ART). ART emphasizes the role of nature in restoring attention. We then discuss essentials of experiments on the causal influences of nature. Next, we expand the concept of ART to include modern, designed environments. We propose a wider perspective termed attentional ecology, in which attention behavior is viewed within a larger system involving the human and their interactions over time with environmental demands. When the ecology is optimal, mental functioning can be a positive “flow” that is productive, sustainable for the individual, and sometimes creative.

Landscape configuration and forest structure assume an increasing importance as determinants of animal communities. This paper focused on nocturnal lepidoptera inhabiting alder patches in the Sila National Park, Italy. According to their shape, patches were divided into linear and compact ones to disentangle the role of forest structure and landscape configuration in determining the composition of nocturnal lepidopteran communities at different observation scales. We used the Mann-Whitney test for medians to Shannon diversity, Equitability, Fisher’s alpha, and nestedness to test differences among moth communities. We found that compact patches inhabit richer and more abundant communities. The abundance-based Correspondence Analysis showed moth communities clustered according to woodlot shape, except a compact woodlot having a linear-like moth community because entirely surrounded by grasslands. Percentage of forested area and abundance and composition of communities are positively correlated at 50 and 200 m buffers, while correlations are absent at smaller and larger buffers. Our results demonstrated that a width of 50 m may not be sufficient to give proper functionality to the wooded area, at least for moths. As consequence, planning of forest restorations should consider the importance to increase structural habitat continuity at larger scales.

Coaxial rotors can be found in multirotor vehicles for the added thrust compared to independent rotors while keeping similar area footprints but, performance losses should be considered. This experimental study analyzes the effects of varying motor throttle and propeller pitch values in motor-propeller systems with two to four coaxial rotors. The results show that in a two-rotor coaxial system, to lessen the adverse effects of a front rotor’s backwash and to operate at the maximum performance, only the back motor should be operated initially up to 75% duty cycle before using the front motor up to its 75% duty cycle. Additional thrust requirements should be generated from the back rotor and then from the front rotor up to their maximum duty cycles. In two, three, and four-rotor coaxial setups, total thrust output generated is 1.6, 2.1, and 2.5 times the thrust output at system thrust performance of 86%, 76%, and 66%, respectively of that of an isolated rotor. In a four-rotor coaxial setup, maximum system performance is achieved when the propeller pitch values are gradually increased from the first to the last rotor. The gradual increments in propeller pitch values also result in more uniform thrust sharing among rotors.

Inflammatory bowel disease (IBD), including Crohn’s Disease (CD) and Ulcerative Colitis (UC) are chronic multifactorial disorders which affect the gastrointestinal tract with variable extent. Despite extensive research, their etiology and exact pathogenesis are still unknown. Cell-free DNAs (cfDNAs) are defined as any DNA fragments which are free from origin cell and able to circulate into bloodstream with or without microvescicles. CfDNAs are now being increasingly studied in different human diseases, like cancer or inflammatory diseases. However, to date it is unclear how IBD etiology is linked to cfDNAs in plasma. Extrachromosomal circular DNA (eccDNA) are non-plasmidic, nuclear, circular and closed DNA molecules found in all eukaryotes tested. CfDNAs appear to play an important role in autoimmune diseases, inflammatory processes, and cancer; recently, interest has also grown in IBD, and their role in the pathogenesis of IBD has been suggested. We now suggest that eccDNAs also plays a role in IBD. In this review we have comprehensively collected available knowledge in literature regarding cfDNA, eccDNA, and structures involving them such as neutrophil extracellular traps and exosomes, and their role in IBD. Finally, we focused on old and novel potential molecular therapies and drug delivery systems, such as nanoparticles, for IBD treatment.

Gol'denveizer's problem of a torus has been analyzed by Audoly and Pomeau (2002) and Sun (2021). However, all of the investigations of Gol'denveizer's problem of an elastic torus have been linear. In this paper, the finite element method is used to more accurately address this problem. Furthermore, Sun (2021) cannot be solved by nonlinear analysis. We research the nonlinear mechanical properties of Gol'denveizer's problem of circular and elliptic tori, and relevant nephograms are given. We study the buckling of Gol'denveizer's problem of an elastic torus, and propose failure patterns and force-displacement curves of tori in the nonlinear range. Investigations reveal that circular tori have more rich buckling phenomena as the parameter a increases. Gol'denveizer's problem of the buckling of an elliptic torus is analyzed, and we find a new buckling phenomenon called a "skirt." As a/b increases, the collapse load of an elliptic torus of the Gol'denveizer problem is enhanced gradually.

Various efforts have been made to detect minimum value of glucose in any medium like water or body buffer solutions with high-sensitivity, accurate, and low-cost sensors in order to enhance life style. Therefore, the present study was done to investigate reliability of two-dimensional plasmonic structure by circular dichroism (CD) and ellipsometry tools in different concentrations of glucose. Our results confirmed a dependency of the CD signal on glucose concentrations and also a very good sensitivity based on the phase difference between each polarization in ellipsometry parameters with the help of an achiral plasmonic structure.

Microgrid is one of the promising green transition technologies that will provide enormous benefit to the seaport, as a solution to the major concerns in this sector, namely energy crisis, economical and environmental pollution. However, finest design of the microgrid is a challenging task considering different objectives, constraints and uncertainties involved. To ensure the optimal operation of the system, determining the right configuration framework and size for each component in the seaport microgrid at the minimum cost is a vital decision at the design stage. This paper aims to design a hybrid system of seaport microgrid with optimally sized component .The selected case study is the Port of Aalborg, Denmark. The proposed grid-connected structure consists of renewable energy sources (photovoltaic system and wind turbines), an energy storage system and cold ironing as seaport’ loads. The architecture is then optimized by utilizing HOMER to meet the maximum load demand by considering a few parameters such as solar global horizontal irradiance, temperature and wind resources. Then, the best configuration framework is analyzed in terms of economic feasibility, energy reliability and environmental impact.

The performance consistency of an RF MEMS switch matrix is a crucial metric, which directly impacts its operational lifespan. An improved crossbar-based RF MEMS switch matrix topology, the SR-Crossbar, was investigated in this article. An optimized port configuration scheme was proposed for the RF MEMS switch matrix. Both the utilization probability of individual switch nodes and path lengths in the switch matrix achieve best consistency simultaneously under the proposed port configuration scheme. One significant advantage of this scheme lies in that it only adjusts positions of input and output ports, with topology and individual switch nodes kept unchanged. This grants it a high level of generality and feasibility, and also introduces an additional degree of freedom for optimizations. The article also constructed a universal utilization probability function of single nodes, and formulated an optimization objective function for the SR-Crossbar RF MEMS switch matrix, which provides a convenient approach to directly solving the optimized port configuration scheme for practical applications.

The motion of a circular elastic plate floating on the surface is investigated in the time–domain. The solution is found from the single frequency solutions and the method to solve for the circular plate is given using the eigenfunction matching method. Simple plane incident waves with a Gaussian profile in wavenumber space are considered and a more complex focused wave group is considered. Results are given for a range of plate and incident wave parameters are investigated. Code is provided to show how to simulate the complex motion.

In this paper, a novel deep learning approach based on conditional FLOW is proposed for sea clutter augmentation. Sea clutter data augmentation is important for testing detection algorithms for maritime remote sensing and surveillance due to the expensive and time-consuming nature of sea clutter data acquisition. While the conventional parametric methods face challenges in finding appropriate distributions and modeling time correlations of the sea clutter data, the proposed deep learning approach, GCC-FLOW , can learn the data distribution from the data without explicitly defining a mathematical model. Furthermore, unlike the existing generative deep learning approaches, the proposed GCC-FLOW is able to synthesize sea clutter data of arbitrary length with the stable autoregressive structure using conditional FLOW . In addition, the proposed algorithm generates sea clutter data not only with the same characteristics of the training data, but also with the interpolated characteristics of different training data by introducing a global condition variable corresponding to the target characteristic such as sea state. Experimental results demonstrate the effectiveness of the proposed GCC-FLOW in generating sea clutter data of arbitrary length under different sea state conditions.

Two beneficial characteristics of aircraft generators are having armature windings and PM excitation sources placed on the stator side (maintenance and thermal management) and having a clear-cut rotor without permanent magnets or excitation windings (vulnerable at high speeds due to associated centripetal mechanical stresses). Within this framework, a doubly-salient permanent magnet (DSPM) generator was conceived by optimizing the stator size and rotor structure to minimize the torque ripple and maximize the RMS voltage value per turn of each generator phase. A Multi-Objective Design Strategy based on a 2D finite element analysis was used, being set to have characteristics closest to optimal for a Boeing 767 turbine, that is, the necessary electromotive force for a required power of 90 kW at 3000 rpm, feeding a simplified Boeing 767 electrical power distribution system. The results show that the machine could not deliver the required power at 3000 rpm since the 2D finite elements analysis demonstrates that the 2D model gives optimistic results when compared with the 3D FEM model. However, with a 3D finite element analysis of the machine feeding the aircraft load, it was seen that the machine’s efficiency is 92%, suggesting this machine can be a plausible solution.

Abstract: Chemical investigation of the leaves from Ageratina glabrata yielded four new thymol derivatives, namely: 10-Benzoyloxy-8,9-dehydro-6-hydroxythymol isobutyrate (4), 10-benzoyloxy-8,9-dehydro thymol (5), 10-benzoyloxythymol (6) and 10-benzoyloxy-6,8-dihydroxy-9-isobutyryloxythymol (7). In addition, (8S)-10-benzoyloxy-8,9-epoxy-6-hydroxythymol isobutyrate (1), together with other two already known thymol derivatives identified as: 10-benzoyloxy-8,9-epoxy-6-methoxythymol isobutyrate (2) and 10-benzoyloxy-8,9-epoxythymol isobutyrate (3). In this paper, we wish to publish the structures and complete assignments of ¹H and ¹³C NMR data of compounds 1 – 7, and the absolute configuration for compound 1, unambiguously established by single crystal X-ray diffraction, and evaluation of the Flack parameter. The in vitro antiprotozoal assay showed that compound 1 and its derivative 1a were the most potent antiamoebic and antigiardial compounds. Both compounds showed selectivity and good antiamoebic activity like emetine and metronidazole, respectively, two antiprotozoal drugs used as positive controls. In relation of anti-propulsive effect, compound 1 and 1a showed moderate inhibitory activity, their activities were comparable to quercetin and compound 9, respectively, two natural antipropulsive compounds used as positive controls. These data suggest that compound 1 may play an important role in antidiarrheal properties of Ageratina glabrata.

This paper presents a comprehensive cost-benefit analysis of producing alternative phosphorus (P) fertilizers from recycled water treatment residuals (Fe-WTR) and cowshed effluents, under the umbrella of circular economy approach. Fe-WTR is compared to a synthetic adsorbent, layered double hydroxide (LDH). Dairy wastewater is used as a P source for both adsorbents. The cost of 1 ton P-Fe-WTR sums up to 329 Euro. In contrast, the use of synthetic adsorbents (P-LDH) incurs significantly higher costs, amounting to 3329 Euros per ton, underscoring the economic advantage of utilizing waste-derived materials. Adopting Fe-WTR fertilizer not only offers substantial cost savings by avoiding landfill fees (40-150 Euros per ton) and wastewater discharge fines (500 Euros per ton) but also reduces environmental impacts. This sustainable method mitigates eutrophication and pollution, presenting a dual benefit of cost-effectiveness and environmental protection. Although our results are based on a specific case study, they reflect the potential value of extending the circular economic approach to P production worldwide: Recycling P from waste streams can be economically viable and environmentally preferable at large, aligning with global sustainability goals and demonstrating the practicality of circular economy principles in environmental management.

The global demand for rubber is on a steady rise, which is driven by the increasing production of automobiles and the growing need for industrial, medical, and household products. This surge in demand has led to a significant increase in rubber waste, posing a major global environmental challenge. End-of-life tire (ELT) is a primary source of rubber waste, which possesses significant environmental hazards due to its massive stockpiles. While landfilling is a low-cost and easy-to-implement solution, it is now largely prohibited due to environmental concerns. Recently, ELT rubber waste has garnered considerable attention for its potential applications in civil engineering and construction. These applications not only enhance sustainability but also foster a circular economy between ELT rubber waste and the civil engineering and construction sectors. This review article concentrates on the recent research progress and challenges in the civil engineering applications of ELT rubber waste. It also discusses commercially available recycled rubber-based construction materials, their properties, testing standards, and certification. To the best of the authors' knowledge, this is the first time such a discussion on commercial products has been presented.

The coordination of policy, makers and materials is critical to the success of circular city development. The network of maker activities in the city of Leuven is a flagship initiative that illustrates the mechanisms that support integrated circular urban production. This paper draws on the Pop-Machina project, funded by EC Horizon 2020, which identifies the links between the maker movement and the circular economy in seven European cities. The case study project in Leuven, confirmed as the most impactful amongst those studied in the Pop-Machina project, is examined to assess how local knowledge and policy measures, can provide a means of activating a circular maker ecology. Through desk research, spatial urban analysis and interviews with key stakeholders, this paper provides a critical narrative of the development, success factors and hurdles related to circular making processes in the city. It demonstrates how hybrid makers are supported by local, national, and international policy on the one hand, and by integration with the city’s community, educational and business groups on the other. It is this constellation of social, political, and spatial conditions that lies at the success of the project.

The paper describes a new formula for calculating the mutual inductance between a thin conical sheet inductor and a filamentary circular loop, which are coaxial. The presented formula is derived semi-analytically using the complete elliptic integrals of the first, second, and the third kind, along with the integral term which will be solved numerically. The results are validated using double and single integration methods, as well as the semi-analytical formula. The mutual inductance between a thin wall solenoid and a filamentary circular loop can be obtained using the new formula for the conical coil and circular loop. Presented formulas can be useful in various applications, such as broadband RF and wireless power transfer systems that utilize conical inductors. Overall, the paper presents a valuable contribution to the field of inductor design and can be useful in various applications involving conical inductors.

This paper presents the experimental and numerical studies of the vertical stress distribution beneath the centerline of circular footings resting on the sand. Vertical stress values due to circular load in medium-dense sand were measured using soil stress transducers. Reduced-scale laboratory model tests were carried out in a square-shaped test box and vertical stresses were measured at the centerline of the circular footing at different depths of the sand. In order to determine the effect of footing width on vertical stress distribution, laboratory experiments were performed on circular footings of different diameters. In addition, a series of finite element analyses was carried out on the test model to validate the findings of the experimental study. In the numerical analysis, the sand was modeled as a non-linear elastoplastic material. The analyses were performed using the finite element method with two-dimensional axisymmetric and three-dimensional conditions. The results obtained from laboratory model tests and numerical analysis were compared with the vertical stress values obtained from the theoretical solution in the literature. Vertical stress distribution in horizontal planes at any depth from the footing base shows the same characteristic form in all methods. However, some differences were observed between experimental, numerical, and theoretical results and discussed.

The article presents an experience based on the design of DIY materials (Do-It-Yourself) as a phenomenon that contributes to the circular economy, making use of household waste and organic binders. The development context is the southernmost Industrial Design School in Latin America, where students are educated through the transfer of knowledge emphasized on the experimentation and territory assessment. Methodology corresponds to the traditional industrial design process, inserting DIY design of materials in the strategic stage. Objective and subjective variables are determined applied in the definition of new materials, being able to determine a range of proposals based on household waste. Citrus × Sinensis, Peperomia caperata (Piperaceae), Radiata pine veneers, among them, which are conceived by students to be self-produced at the user level. The results are materials elaborated based on household waste, exemplified with three types based on organic husks. Beyond findings associated to technique, compatibilities between residual materials and results expressed in materials and catalogs, it is possible to educate future designers on the innovative theme, with the potential to improve life quality of people and their environments.

Combined systems for power production and thermally activated cooling have a high potential for improving the efficiency and utilisation of thermal systems. In this regard, various configurations have been proposed and are comprehensively reviewed. They are primarily based on absorption systems and the implementation of multiple levels of complexity and flexibility. The configuration of the absorption power and cooling combined cycle proposed herein has wide commercial applicability owing to its simplicity. The configuration of the components is not new. However, the utilisation of aqueous salt solutions, the comparison with ammonia chiller and with absorption power cycles, the focus on parameters that are important for real-life applications, and the comparison of the performances for constant heat input and waste heat recovery are novel. The proposed cycle is also compared with a system based on the organic Rankine cycle and vapour compression cycle. An investigation of its performance proves that the system is suitable for a given range of boundary conditions from a thermodynamic standpoint, as well as in terms of system complexity and technical feasibility. New possibilities with regard to added power production have the potential to improve the economics and promote the use of absorption chiller systems.

To understand functions of biomolecules such as proteins, not only structures but their conformational change and kinetics are important to be characterized but its atomistic details are hard to obtain both experimentally and computationally. We review our recent computational studies using novel enhanced sampling techniques for conformational sampling of biomolecules and calculations of their kinetics. For efficiently characterizing the free energy landscape of a biomolecule, we introduce the multiscale enhanced sampling method, which uses a combined system of atomistic and coarse-grained models. Based on the idea of Hamiltonian replica exchange, we can recover the statistical properties of the atomistic model without any biases. We next introduce the string method as a path search method to calculate the minimum free energy pathways along a multidimensional curve in high dimensional space. Finally we introduce novel methods to calculate kinetics of biomolecules based on the ideas of path sampling: One is the Onsager-Machlup action method, and the other is the weighted ensemble method. Some applications of above methods to biomolecular systems are also discussed and illustrated.