The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

This study investigates the impact of vertical greenery systems (VGS) applied to heavyweight walls on indoor thermal conditions in a building module situated in the Mediterranean climate of Catania, Italy. Using dynamic simulations in TRNSYS, the research compares the thermal behavior of walls constructed from hollow clay blocks (Poroton) and lava stone blocks with a lightweight wall setup already in place at the University of Catania. The primary focus is on evaluating the VGS’s effect on reducing peak inner surface temperatures and moderating heat flux fluctuations entering the building. The findings indicate that adding a vertical greenery layer to heavyweight walls can decrease the peak inner surface temperature by up to 1.0°C compared to the same wall without vegetation. However, the greenery’s impact on mitigating heat flux fluctuations is less pronounced than in the case of the lightweight wall. This research underscores the potential of green facades in enhancing indoor thermal comfort in regions with climates similar to the Mediterranean, providing valuable insights for sustainable building design and urban planning.

The thermal insulation properties of building walls are critical to the overall energy efficiency and comfort of a building. One important factor that can affect these properties is the type of bricks used in construction. Bricks can vary in their geometry and thermal coefficient, which can impact their ability to transfer heat through the wall. The geometry of a brick can affect its thermal properties by altering the amount of air trapped within it and the surface area available for heat transfer. Hollow bricks or those with complex geometries may have lower thermal conductivity than regular solid bricks due to the air pockets trapped within them. Conversely, larger surface areas on the exterior of the brick can increase heat transfer. The thermal coefficient of clay, a common material used in brick production, is another important factor. Clay has a relatively low thermal conductivity, meaning it is a poor conductor of heat. However, the quality of the clay, as well as the firing temperature and duration used in brick production, can impact its thermal coefficient. Higher firing temperatures and longer firing times can result in a more compact and dense clay brick, which can improve its thermal properties. In summary, the thermal insulation properties of building walls can be significantly affected by the type of bricks used in their construction. It is important to consider the geometry and thermal coefficient of the bricks when designing a building to achieve the desired level of thermal insulation. By selecting bricks with appropriate properties, designers can help to improve the energy efficiency and comfort of the building while reducing its environmental impact.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

This study assesses Human Thermal Comfort in two selected areas: a Green Infrastructure (GI) area represented by a garden and a high-rise building area, in the Central Business District (CBD) of Melbourne, Australia. Three-dimensional microclimatic modelling software, ENVI-met version 4 was used to simulate the microclimate. The indices of Predicted Mean Vote (PMV), Physiological Equivalent Temperature (PET) and Universal Temperature Climate Index (UTCI) were used to quantify the level of thermal comfort in the research areas. The simulation results showed that at midday, the difference in temperature between the garden area and the high-rise building area was approximately 1°C. Increasing temperatures at midday led to a change in the level of thermal comfort for both the areas, even though it was not significant. In general, the thermal perception in the GI area was slightly ‘cooler’ than in the high-rise building area. The results of the study indicated the important role of GI in improving the thermal comfort in urban areas.

Thermal comfort is extremely important in architecture, especially in environments with more people spending longer on studies or intellectual activities. This research describes a case study to investigate university buildings' energy and thermal performance as a part of the ANEEL program. Due to this importance, and the need to save energy in Brazilian public buildings, the ANEEL-the Brazilian Energy Electricity Regulatory Agency, launched 2016 a national program focusing on energy efficiency in public universities around the country. University offices and classrooms require high intellectual effort; thus, environmental comfort is critical for maintaining its users' physical and mental health. This study included a pre-diagnosis of the performance of the envelope, lighting, and air conditioning systems and a survey about the quality of the environments from the users' point of view. The Prescriptive Method of the Brazilian Labeling Program (PBE) for Commercial, Service, and Public Buildings (RTQ-C) assessed the building performance. Statistical analysis was applied to correlate the quality and thermal preference of the users from the PMV/PPD. The results showed a high rate of thermal discomfort in both environments of the studies, even when using air conditioning.

Season plays a key role in the development of outdoor spaces for pedestrians in hot humid cities. This research studies the influence of seasonal variations on pedestrian thermal comfort on the pedestrian level by means of meteorology and field observations of selected footpaths in the major tourist area of Malacca. This experiment was carried out on selected clear calm days indicative of each season during the development of a research project, and hourly meteorological transects from 10:00 am to 6:00 pm and questioned 200 respondents on their thermal awareness, comfort, and preferences were conducted. Adaptation, thermal comfort vote, thermal preference, age, season and hour of the day were significant non-meteorological factors, apart from meteorological information. The findings of analyzes showed that the thermal experience and expectation existed and in different seasons people changed perceptions for the outside thermal environment. Almost 80% local tourist and 55 % international tourist was accepted Physiologically Equivalent Temperature (PET) range affected by the local climate and thermal adaptation. The subjective thermal sensation on physiological equivalent temperature generated an acceptable physiological equivalent temperature of 32.6°C to 36.8°C based on the seasonal variations for Malacca tourist zone in Malaysia. These findings shed light on the optimal design of outdoor spaces for increasing the utilization rate. The seasonal variation must be taken into account so that the outdoor landscape design provides more opportunities for different seasons to communicate with the atmosphere and so enhance thermal comfort and utilization.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The urban heat island (UHI) is mostly due to urbanization. This phenomenon in concert with the high temperatures caused by global climate change may profoundly affect human thermal comfort, which can influence human productivity and morbidity especially in spring/summer period. The main objective of this investigation was to determine changes in degree of thermal comfort of Mexico City’s inhabitants and compare it with the physiological equivalent temperature (PET) to evaluate whether PET and its categorization are adequate to be applied in Mexico City. A series of microclimatological measurements to estimate PET were made in four sites including the city´s center. Concomitantly, a series of surveys of thermal perception were applied to 1300 passersby. The results show that PET has increased from 1990 to 2020 from 0.1208 °C/year to 0.1498 °C/year in the study sites, besides overestimating the degree of thermal comfort of people according to the stablished categories or classes. It is concluded that it is necessary to adjust thermal stress categories. Knowing the percentage of people without thermal comfort will lead us to determine different ranges in environmental parameters to define an acceptable environment for most people.

This empirical study investigates large urban park cooling effects on the thermal comfort of occupants in the vicinity of the main central park, located in Madrid, Spain. Data were gathered during hot summer days, using mobile observations and a questionnaire. The results showed that the cooling effect of this urban park of 140 ha area at a distance of 150 m is able to reduce temperature by an average of 0.63°C and 1.28°C for distances of 380 m and of 665 meters from the park. Moreover, the degree of the Physiological Equivalent Temperature (PET) index at a distance of 150 meters from the park is on average 2°C PET and 2.3°C PET less compared to distances of 380 m and 665 m, respectively. Considering distance from the park, the correlation between occupant Perceived Thermal Comfort (PTC) and PET is inverse. That is, augmenting the distance from park increases PET, while the extent of PTC reduces accordingly. The correlation between these two factors at the nearest and furthest distances from the park is meaningful (P-value <0/05). The results also showed that large-scale urban parks generally play a significant part in creating a cognitive state of high-perceived thermal comfort spaces for residents.

Since people spend most of their time in indoor environments, the objective of this work was to study indoor air quality perception and its effects on users’ thermal comfort. Based on previous data from a building with a central air-conditioning system and two mixed-mode buildings located in the humid subtropical climate of Florianópolis, southern Brazil, statistical analyses were performed. Each user subjective answer obtained through a questionnaire was combined with the corresponding environmental conditions – measured using microclimate stations, a portable thermo-anemometer and a CO2 analyser. Results showed that improvement in air quality was associated with the reduction of air temperature and humidity ratio. Also, there was a significant influence of thermal, air movement and humidity sensation and acceptability of air quality perception. Users felt more satisfied or neutral with air quality for being in thermal comfort, and not because of the CO2 level – which means that air quality perception is influenced by factors other than CO2. This study recommends the implementation of an air exchange device in split air-conditioners with air recirculation used in mixed-mode buildings in Brazil. It is important to provide suitable indoor ventilation to reduce pollutants concentration, ensure good air quality and prevent respiratory diseases.

Magnesium supplementation has recently attracted attention as effective in the management of diabetes and its related complications though its mechanisms of action is yet to be fully unraveled. This study was carried out to determine the effects of magnesium supplementation on body weight, fasting blood sugar, Oral glucose tolerance (OGTT 2 and OGTT 4), glucose transporter isoform 2 (GLUT2), GLUT4 and insulin receptor (INSR) mRNA expressions in streptozotocin-nicotinamide induced diabetic Sprague dawley rats. A total of 24 Sprague dawley rats (Four groups of six rats each) were used for this study, and the treatment was for 28 days. Group 1: Normal control rats were given distilled water; Group 2: Metformin treated rats were given 100 mg/kg body weight; Group 3: Metformin + Magnesium treated rats were given 100 mg/kg and 1000 mg/kg body weight respectively; Group 4: Diabetic untreated rats given distilled water. Data were analyzed statistically using Analysis of Variance (ANOVA) and graphically by Graph pad prism. The GLUT4 and INSR gene expressions of Group 3 were significantly (p<0.05) upregulated when compared with Group 4. There was significant (p<0.05) decrease fasting blood sugar and GLUT2 mRNA level in the treated diabetic rats but the metformin-magnesium supplement treated group showed more decrease (p<0.05) when compared with the group treated with metformin only. This study demonstrates that magnesium may mediate effective metabolic control by stimulating insulin sensitivity, and upregulating mRNA levels of GLUT4, INSR as well as improving glucose tolerance in diabetic rats. Therefore, magnesium supplementation appears to have a beneficial role and improves glucose uptake by cells in those at high risks of diabetes. Magnesium supplementation, Metformin, INSR, GLU4, glucose tolerance.

Lack of due attention to the orientation of streets and establishment of urban blocks without regard for climatic characteristics and conditions of the environment have an adverse effect on thermal comfort in open urban spaces. Construction of new settlements without taking into account climatic requirements undermines thermal comfort for pedestrians and other users, especially in cold regions. Considering the coldness of the region under study and the significance of the orientation of streets in absorbing radiation and providing heat to outdoor urban spaces, this study investigates the effect of the orientation of streets on microclimatic comfort in one of the residential towns of Hamadan City in Iran. For this purpose, microclimate simulation was performed using ENVI-met software. A residential block with four different orientations (the most common orientations of its surrounding buildings) were simulated in the coldest day of winter and the hottest day of summer. The results suggest that streets have different thermal behavior in different orientations. Orientation affects mean radiant temperature (Tmrt), the duration of exposure to direct sunlight, wind speed, and physiological equivalent temperature (PET), which are all important factors in thermal comfort. Based on these findings, north-south streets in Hamedan receive more radiant temperature during winter compared to other simulated orientations and provide more desirable thermal comfort. The average PET value on a winter day at a point on the north-south passage was 4.5-8 °C warmer than other orientations. In summer, streets with intercardinal orientations (i.e., northeast-southwest and northwest-southeast) provided the lowest PET (about 2 °C cooler than other orientations) and better thermal comfort

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

Zinc cobalt oxide-zinc hydroxide (ZnCo2O4-Zn(OH)2) microspheres were successfully fabricated on carbon cloth via a sample hydrothermal method. The surface morphology of these microspheres and their efficacy in degrading methyl violet were further modulated by varying the thermal annealing temperatures. The manipulation of thermal annealing temperatures was pivotal in adjusting the porosity of ZnCo2O4-Zn(OH)2 microspheres to amplify their photocatalytic performance. Various analytical techniques were utilized to evaluate the physical and chemical properties of the ZnCo2O4-Zn(OH)2 microspheres, including field-emission scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, field-emission transmission electron microscopy, X-ray photoelectron spectroscopy, and UV-vis spectroscopy. Compared to untreated ZnCo2O4-Zn(OH)2 microspheres, those subjected to thermal annealing exhibited increased specific surface area and light absorption capacity, rendering them highly effective photocatalysts under UVC light exposure. Subsequent studies have confirmed the superior performance of ZnCo2O4-Zn(OH)2 microspheres as a reusable photocatalyst for degrading methyl violet and tetracycline. Additionally, trapping experiments during the photodegradation process involving ZnCo2O4-Zn(OH)2 microspheres have identified hydroxyl radicals (·OH) and superoxide radicals (·O2–) as the primary reactive species.

Local thermal comfort (TC) and draught rate (DR) has been studied widely. There has been more meaningful research performed in controlled boundary condition situations than in actual work environments involving occupants. TC conditions in office buildings in Estonia have been barely investigated in the past. In this paper, the results of TC and DR assessment in five office buildings in Tallinn are presented and discussed. Studied office landscapes vary in heating, ventilation and cooling (HVAC) system parameters, room units and elements. All sample buildings were less than six years old, equipped with dedicated outdoor air ventilation system and room conditioning units. The on-site measurements consisted of TC and DR assessment with indoor climate questionnaire (ICQ). The purpose of the survey is to assess the correspondence between HVAC design and the actual situation. Results show, whether and in what extent the standard-based criteria for TC is suitable for actual usage of the occupants. Preferring one room conditioning unit type or system may not guarantee better thermal environment without draught. Although some HVAC systems observed in this study should create the prerequisites for ensuring more comfort, results show that this is not the case for all buildings in this study.

A variety of factors ranging from ethnicity and occupants’ lifestyles to local climatic characteristics of any studied location and people’s age factors can affect thermal comfort assessment globally. Due to the detrimental impact of climate change, the building industry has started to implement energy efficiency schemes while considering the thermal comfort of vulnerable population both for the society and any sphere of economy. Although, considering human-based approaches have been neglected by other scholars in thermal comfort studies. This paper reviews energy effectiveness of state-of-the-art passive systems in providing neutral adaptive thermal comfort for elderly people, through exploring passive design strategies in four distinct climates namely, Canada, India, Abu Dhabi and the South-eastern Mediterranean basin. The aim of the study is to analyze the available data provided by the ASHRAE Global Thermal Comfort Database II version record 2.1. The main objective of the study is to develop an effective methodological framework for the on-going development of adaptive thermal comfort theory. To this extend, this study presents a comprehensive review on the assessment of energy effectiveness of passive design systems. To accomplish this, the impact of climate change factor in passive design systems was investigated. The meta-analysis method was adopted to determine the input variables for the statistical analysis. Cramer’s V and Fisher’s Exact tests were used to assess occupants’ thermal sensation votes (TSVs). The findings revealed that there are discrepancies detected between the in-situ field experiments and the data recorded in the ASHRAE Global Thermal Comfort Database II. According to the Köppen-Geiger climate classification, it was found from the study that the slightly high temperature fluctuations were identified in India where the weather is dry and savanna climate. The study findings contribute to the development of adaptive thermal comfort theory by reviewing the existing methodologies globally. Furthermore, a critical review on the significance of occupants’ age differences should be conducted in the identification of neutral adaptive thermal comfort.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

The combined effects of global warming and increasing urban heat islands (UHIs) on air temperature and heat stress in cities are notable physical and mental health implications for citizens. With research having shown the effective role of urban green spaces in decreasing urban heat, this study investigated the cooling effect of a large urban park on thermal comfort outside the park area, from psychological and physiological perspectives. The studied park is located in the center of Madrid and adjacent to UHI. The study was performed by conducting field measurements and a survey with questionnaires. The measurements made on six summer days (with two-week intervals) showed that the park’s cooling effect could decrease the air temperature by 2.4-2.8°C right up to the edge of the heat island (600m), and decrease the physiological equivalent temperature (PET) by about 3.9°C. By decreasing air temperature and PET, this park was also shown to increase the perceived thermal comfort (PTC) of the citizens from the psychological perspective in the defined area of effect. This perceived thermal comfort was found to have a significant inverse relationship with PET (P-value <0.05). The examination of cognitive maps drawn by citizens showed that out of the 145 respondents, 68.3% marked the park as the area that they perceive as having the greatest thermal comfort, and prefer as the place to spend time enjoying thermal comfort, irrespective of its distance from their location.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

Indoor environmental comfort is fundamental to human health as people spend 90% of their time indoors. This aspect is even more crucial in hospitals, where the concept of health is closely linked to well-being, ethics, and environmental aspects. Emerging methodologies and technologies such as Digital Twin, Building Information Modeling, the Internet of Things, sensing technologies, and data analytics offer new opportunities to ensure healthier environments and more efficient building management. This paper provides an assessment of how digitalization can support decision-making processes related to maintaining high levels of indoor environmental comfort in hospital settings, particularly by analyzing how real-time data processing and the application of machine learning can promote proactive interventions in these facilities. The methodological approach was based on four phases: defining the objectives of the digital twin, identifying the input data to build and feed the digital model, defining the KPIs to evaluate the system's correct functioning, and identifying the enabling technologies to be integrated into the system to achieve the set goal. The result is a digital twin for managing the operating room and its related services, with the aim of guiding decisions based on accurate data and improving operational efficiency, levels of environmental comfort, and safety regarding the diffusion of medical gases.

Manipulating cloth-like deformable objects (CDOs) is a long-standing problem in the robotics community. CDOs are flexible (non-rigid) objects that do not show a detectable level of com- pression strength while two points on the article are pushed towards each otherand include objects such as ropes (1D), fabrics (2D) and bags (3D). In general, CDOs’ many degrees of freedom (DoF) introduce severe self-occlusion and complex state-action dynamics as significant obstacles for perception and manipulation systems. These challenges exacerbate existing issues of modern robotic control methods such as imitation learning (IL) and reinforcement learning (RL). This review focuses on the application details of data-driven control methods on four major task families in this domain: cloth-shaping, rope manipulation, dressing and bag manip- ulation. Furthermore, we identify specific inductive biases in these four domains that present challenges for more general IL and RL algorithms, and summarise the future direction for the development of the field.

Heat pumps are increasingly becoming a key solution in the quest for decarbonization, offering a significant advantage over traditional boilers due to their superior energy efficiency. Not only can heat pumps provide both heating and cooling, but they also achieve thermal efficiencies exceeding 500%, which can seem to defy conventional expectations. The outdoor unit of a heat pump consists of about twenty main components, one of which is a complex network of copper pipes and sheets welded to valves, connectors, and other fittings. This set involves over thirty welded joints, highlighting a significant opportunity for reducing manufacturing time through process optimization. Copper is a critical material extensively used in various applications due to its excellent thermal and electrical conductivity. However, these very properties make welding copper particularly challenging, especially when aiming to automate and streamline industrial processes. Traditionally, connecting copper pipes and fittings is done through brazing, yet, alternative methods such as LASER welding, electron beam welding, resistance welding, friction welding, and ultrasonic welding also exist. This study focuses on the ultrasonic welding of copper, aiming to identify the optimal parameters that maximize the mechanical strength of overlapping joints and ensure effective tube sealing. Experimental results showed that for copper sheets, the best outcomes were achieved with a welding time of 3 s and a pressure of 6 bar. For tube sealing, the optimal conditions were a welding time of 3 s and a pressure of 4 bar. For both scenarios, the same variables were used, retention time of 0.62 s, initial pressure of 2 bar, retention pressure of 2 bar and sonotrode rising pressure of 3 bar. The analysis reveals that ultrasonic welding of copper can achieve both robust mechanical strength and reliable sealing, making it a promising technique for industrial applications.

The overall comfort experienced by an individual in an n-dimensional space can be theoretically constructed using a mathematical equation, that relates the comfort experienced by an individual in a particular point in space with spatial points associated with higher comfort attributes and the desirable factors affecting the current environmental space.

This study uses simulation and experimental methodologies to explore the efficacy of bi-sectional horizontal kinetic shading systems (KSS) featuring horizontal fins in enhancing daylight comfort across various climates. Given the increasing energy demands and shifting climatic patterns, optimizing daylight levels while minimizing solar heat gain is vital. The paper introduces a bespoke horizontal bi-sectional KSS, simulated in three distinct climates—Wroclaw, Tehran, and Bangkok—using Climate Based Daylight Modelling methods with Ladybug and Honeybee tools in Rhino software. The study employs standard daylight metrics such as Useful Daylight Illuminance (UDI) and Daylight Glare Probability (DGP), along with custom metrics designed to capture the specific dynamics of the bi-sectional KSS. Initial simulations indicated that the KSS significantly improved daylight distribution and uniformity, reducing glare and over-illumination risks by av. 42.34%. Including KSS switching schedules, which are seldom detailed in similar research, enhances the reproducibility and understanding of findings. Subsequently, a physical reduced-scale mock-up of the bi-sectional KSS was tested under real-weather conditions in Wroclaw (lat. 51° N) during June-July 2024. The mock-up utilized two chambers: one equipped with the prototype of bi-sectional KSS and the second without any protection. The operation of fins was guided by two stepper motors controlled by a Python script running on a Raspberry Pi 3 minicomputer. The control chamber served to benchmark the bi-sectional KSS's efficiency by providing results that would be expected if no shading system were installed. The experimental outcomes supported the simulations, demonstrating the KSS's robustness in reducing high illuminance levels to the target comfort level, thus enhancing indoor visual comfort. The values below 3,000 lux were maintained for 68% of the time. However, it must be explicitly stated that during the June-July 2024 heat waves, the illuminance levels inside the test room momentarily exceeded the comfort threshold of 3,000 lux, reaching up to 4,674 lux. Through quantitative and qualitative analyses, the paper advocates for the broader application and further development of KSS as a climate-responsive shading system in diverse architectural contexts.

This research is dedicated to a comprehensive examination of the strengths and weaknesses inherent in the legal and institutional measures designed to protect cultural heritage in the Republic of Serbia from the adverse effects of natural disasters, including earthquakes, landslides, rockfalls, floods, torrents, storms, hail, and forest fires. The study aims to identify the primary challenges and shortcomings within the existing legal and institutional framework, while also pinpointing and analyzing best practices and potential improvements for the protection system. This research posits a preliminary hypothesis suggesting that challenges may exist within the legal and institutional framework for the protection of cultural heritage in the Republic of Serbia, potentially limiting effective response and recovery following natural disasters. This hypothesis will be further developed and adapted based on the analysis of available data. Data collection for this research was conducted through semi-structured interviews with experts and an in-depth analysis of existing documentation. By conducting interviews with experts in the field, the research seeks to gather critical data and insights that will enhance the understanding of these issues and contribute to formulating viable solutions. The analysis and processing of data were carried out using ATLAS.ti software, which facilitated a comprehensive and systematic examination of the collected qualitative information. Furthermore, an assessment of the current capacity of institutions to respond rapidly and effectively to natural disasters that pose a threat to cultural heritage is a key component of the study. The ultimate goal is to develop recommendations that will fortify the legal and institutional framework, thereby bolstering the resilience of cultural heritage sites in Serbia against future natural disasters. The results of the research, highlight significant deficiencies in the legal framework, inadequate institutional capacities and resources, as well as a lack of proper training for crisis response. The need for improved inter-institutional cooperation and the development of technical-logistical resources is emphasized. This paper represents a significant contribution to the understanding and enhancement of the cultural heritage protection system, providing a foundation for further research and strategy development in this area.

Emergency Medical Response Systems (EMRS) play a vital role in delivering medical aid during disasters. In Serbia, these systems encounter several obstacles due to economic limitations, scarce resources, and ongoing healthcare reforms, all of which affect their performance. This study focuses on examining the risk factors and effectiveness of Serbia's EMRS, identifying systemic issues, and proposing enhancements to improve emergency preparedness for disasters. A survey was conducted across healthcare institutions in Serbia to gather comprehensive insights. The survey explored various aspects, including organizational structures, resource distribution, communication systems, and the speed of emergency responses. Statistical methods such as Pearson's correlation, multivariate regression analysis and chi-square tests were utilized to interpret data collected from 172 healthcare institutions. The multivariate regression analysis of EMS organization identified that factors such as the structuring of working hours and shift patterns are significant predictors, contributing to small but meaningful variations in various EMS outcomes. In contrast, other factors, such as financial resources and the availability of ambulance vehicles, showed more targeted significance depending on the specific EMS aspect being analyzed. Institutions with written mass casualty plans and procedures demonstrate superior effectiveness in EMS activities, excelling in resource allocation, operational continuity, and emergency preparedness, particularly through enhanced coordination and specialized systems for managing large-scale emergencies. The findings highlighted notable disparities in how EMRS are organized, with only 46% of institutions having specific emergency departments. Resource limitations were evident, as many facilities operated with minimal staff and outdated equipment. The communication systems revealed weaknesses, with just 54% having established protocols for handling emergency calls. Response times frequently surpassed international standards, which negatively affected patient outcomes. Additionally, the study found training deficiencies, with 68% of participants expressing a need for further education. Serbia’s EMRS are significantly impacted by systemic issues such as insufficient funding, disjointed service delivery, and inadequate training. Overcoming these challenges necessitates a comprehensive approach that includes boosting financial support, implementing standardized protocols, and fostering enhanced collaboration across different sectors.

Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Through performance analysis using four years of operational data, we achieved a Coefficient of Performance (COP) of 5 on the building load side. This paper confirms the equivalence of the dimensionless production temperature and heat recovery rate, observing nearly identical changes in the dimensionless production temperature over four cycles (eight seasons). Furthermore, we propose an operational method for the following fiscal year that maintains the balance between accumulated storage quantity and pumping volume, based on predictions from this plant's operational pattern.

The central coast is one of the importantly livable regions in China, and green land plays a meaningful role in improving human settlements through regulating ecosystem services. However, the research on spatiotemporal heterogeneity of green land in different urbanized areas are still lacking in this region, which limits the timeliness of reporting on the land-surface thermal properties of residential environment from green land perspective. To address this issue, the synergistic methodology of “artificial numerical technology -- urban interior mixed pixel classification -- surface radiation energy balance model” was applied to investigate the green land change and its impact on human settlements in Rizhao region, which is known for its coastal ecology and greenery in China and obtained the United Nations habitat award. Main conclusions of this study are below: (1) Although total green land decreased by 474.05 km2, resulting in a decrease of 9.17% in its share of the entire study area from 2000-2022 during the urbanization process, but the greening levels improved within the built-up area, with the greening proportion of 25.34% in 2000 and 42.98 km2 in 2022. (2) Differences in green land at different urbanized regions were first observed, namely, urban greening rate was 37.78% in the old urban areas of 2022, while it was up to 46.43% in new urban areas. More attention was paid to the construction of urban green space during urban expansion, which will inevitably bring better visual and comfort experience to residents. (3) Thermal comfort indicators for urban residents were evaluated in latent heat flux (0-457.83 W/m2), sensible heat flux (0-645.09 W/m2), total available energy (254.07-659.42 W/m2) and others. (4) The lowered cooling temperature effect in the middle, high green land density region was 1.05 ℃ and 2.12 ℃ compared to the low-density region, and the average air temperature was 25.86 ℃. Also, spatial patterns of hot and cold uncomfortable areas were displayed in this study. Overall, this study provides the meaningfully practical reference for exploring the spatiotemporal heterogeneity of green land and its impact on residents' environments from the perspective of land-surface thermal properties in coastal areas of China and around the world.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

To assess the efficacy of washing cloth masks, we simulated SARS-CoV-2 contamination in tricoline fabric and tested decontaminants to reduce viral particles. Viral suspensions using two variants (B.1.1.28 and P.1) were inoculated in these fabrics, and the inactivation kinetics were evaluated after washing with various household disinfection products (Soap powder, Lysoform®, Hypochlorite sodium and 70% Alcohol), rinse numbers, and exposure times. Afterward, the fabrics were washed in sterile water, viral RNA extracted and amplified using RT-qPCR. Finally, viral replication in cell cultures was examined. Our findings show that all biocidal treatments successfully disinfected the tissue tested. Some products showed less reduction in viral loads, Soap powder (1.60 x 104, 1.04 x 103), Soap powder and Lysoform® (1.60 x 104, 1.04 x 103) and Alcohol 70% (1.02 x 103, 5.91 x 101) respectively. However, when sodium hypochlorite was used, this reduction was significantly increased (viral inactivation in 100% of the washes). After the first wash, the reduction of viral particles was greater for the P.1 variant than for the B.1.1.28 variant (W = 51759, p 0.05). In conclusion the sodium hypochlorite role on cloth masks disinfection may also have implications for future health emergencies as well as recommended by WHO.

A flexible asymmetric supercapacitor (ASCs) is successfully developed by using the composite of MoO3 and graphene oxide (GO) electrochemically deposited on carbon cloth (CC) (MoO3/rGO/CC) as the negative electrode, the MnO2 deposited on CC (MnO2/CC) as the positive electrode and Na2SO4/polyvinyl alcohol (PVA) as gel electrolyte. The results show that the introduction of GO layer can remarkably increase the specific capacitance of MoO3 from 282.7 F g-1 to 341.0 F g-1. Furthermore, the combination of such good electrode materials and a neutral gel electrolyte renders the fabrication of high-performance ASC with a large operating potential difference of 1.6 V in 0.5 mol L-1 Na2SO4 solution of water. Furthermore, the ASCs exhibit excellent cycle ability and the capacitance can maintain 87 % of its initial value after 6000 cycles. The fact that a light-emitting diode can be lighted up by the ASCs indicates the device’s potential applications as energy storage devices. The encouraging results demonstrate a promising application of the composite of MoO3 and GO in energy storage devices.

Road safety and the effectiveness of the transportation system as a whole are significantly impacted by driver comfort. Road surface quality can play a significant part in the driver’s comfort experienced on roads in any country. This study employs a Random Forest technique to examine the association between road roughness and drivers' comfort during long-distance driving. Using Random Forest, a dependable machine learning technique that can handle big datasets and detect nonlinear correlations, this work aims to shed light on the complex dynamics between road conditions and driver’s comfort. 1,048,576 rows of data from MIRANDA, an application developed at the University of Gustave Eiffel, were used in this study as part of the data collected from a probe vehicle. The data collected includes an International Roughness Index (IRI). The IRI thresholds offer a simple method for assessing driver comfort and road irregularity. While highlighting how uneven and uncomfortable the road is, the research's findings (Road Roughness: SD – 0.73; Driver's Comfort: - Mean, 10.01, SD – 0.64) also contribute to the standardization of road condition evaluation and maintenance communication. This finding is anticipated to aid in the development of strategies for improving the welfare of long-haul drivers and fixing road infrastructure to comply with standard road index, ultimately leading to the creation of more efficient and sustainable transportation systems.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

With the development of the energy sector based on renewable primary sources, structural changes are emerging for the entire national energy system. Initially, it was estimated that energy generation based on fossil fuels would decrease until its disappearance. However, the evolution of CO2 capture capacity leads to a possible coexistence for a certain period with the renewable energy sector. The paper develops this concept of coexistence of the two systems, with the positioning of green hydrogen not only within the renewable energy sector but also as a transformation vector for carbon dioxide captured in the form of synthetic fuels such as CH4 and CH3OH. The paper also analyzes the economic aspects related to price differences for energy produced in the two sectors, as well as their interconnection. The technical aspect, as well as the economic one, for storage through various other solutions besides hydrogen, has been highlighted. The development of the renewable energy sector and its demarcation from the fossil fuel energy sector, even with the transcendent vector represented by green hydrogen, leads to the deepening of dispersion aspects between the electricity sector and the thermal energy sector, a less mentioned aspect in current works but of great importance.

Fabric material was coated with Viruferrin™ and tested for its inactivating properties against the pandemic severe acute respiratory syndrome 2 (SARS-CoV-2) and influenza A viruses. A statistically significant (p<0.0001) decrease in the number of infectious virus particles exposed to Viruferrin-treated fabric when compared with the cotton control for both SARS-CoV-2 and influenza A viruses was observed. For both SARS-CoV-2 and influenza A, Viruferrin-treated fabrics experienced a > 99% virus reduction without saliva after five minutes of contact when compared to the positive control at time point 0. Furthermore, the reusability of the Viruferrin treated fabric was demonstrated by stability for up to 10 washes. The level of anti-viral (SARS-CoV-2) activity remained constant from 5 to 10 washes and demonstrated a significant difference (p<0.0001) from the unwashed untreated material. Applications for this treated fabric are far-reaching, and as a biological face covering offers not only a unique 2-way protection but also is unlikely to cause onward touch transmission.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

The comfort of the elderly in hospital settings requires a special attention from the involved health care professionals, particularly nurses, since hospitalization often generates suffering and discomfort. In such contexts, it is essential to take into account the specific characteristics of the elderly, considering their life experiences and their needs, to promote the health, well-being, and comfort of this population. Hence, the present work aimed to explore the nursing interventions that promote comfort among the elderly in hospital settings. A mixed descriptive exploratory study was conducted, through the application of a questionnaire, using intentional non-probabilistic sampling. The study encompassed 55 elderly individuals hospitalized in a medical service of a public hospital located in Lisbon. The results show that the participants perceived a reasonable level of comfort (5.65 ± 6.46). The following categories emerged from the content analysis: 1) Physical interventions; 2) Psycho-spiritual interventions; 3) Socio-cultural interventions; and 4) Environmental interventions. These findings help to understand comfort-promoting nursing interventions in the studied population. It was concluded that, to improve care quality, comforting interventions should focus on the elderly patient’s individuality, through support activities, empowerment, and the preservation/correction of the surrounding environment. Additionally, the provided care should be based on the real needs, expectations, preferences, and values of the elderly individual.

In the early stage of new vehicle development, the requirements of maximum performance of the air conditioning (AC) system are obtained through Amesim software simulation, but the calibration control of the AC system is usually carried out in the prototype-build vehicle test stage, and the test time is spanned up to 10 months after spring (autumn), summer and winter, of which up to 2 months are for environment chamber tests. Due to the long calibration cycle of AC control in the road test, which seriously affects the vehicle launch time, virtual calibration technology of air conditioning system is developed to shorten the calibration cycle of AC systems and ensure the quality of vehicles. In the project development stage, the calibration control of the vehicle AC system can be realized to carry out the functional test of the AC system in advance. In that, the grade of maturity for the AC system control can be improved, the on-road calibration test cycle can be shortened, and the development cost can be saved.

The objectives were to identify conditions under which mothers may be willing to use telelactation and explore associations between participant characteristics, willingness, and beliefs regarding telelactation use. Mothers 2-8 weeks postpartum were recruited from two Florida maternal care sites and surveyed to assess demographics, breastfeeding initiation, and potential telelactation use. Analyses included descriptive statistics and logistic regression models. Of the 88 participants, most were white, married, earned less than $50,000 per year, had access to technology, and were willing to use telelactation if it was free (80.7%) or over a secure server (63.6%). Fifty-six percent were willing to use telelactation if it involved feeding the baby without a cover, but only 45.5% were willing if their nipples may be seen. Those with higher odds of willingness to use telelaction under these modesty conditions were experienced using videochat, white, married, and of higher income. Mothers with security concerns had six times the odds of being uncomfortable with telelactation compared to mothers without concerns. While telelactation can improve access to critical services, willingness to use telelactation may depend on conditions of use and sociodemographics. During the COVID-19 pandemic and beyond, these findings offer important insights for lactation professionals implementing virtual consultations.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

A new model predictive control (MPC) algorithm is used to select optimal air conditioning setpoints for a commercial office building, considering variable electricity prices, weather, occupancy and lighting. This algorithm, Cost-Comfort Particle Swarm Optimization (CCPSO), is the first to combine a realistic, smooth representation of occupants’ willingness to pay for thermal comfort with a bottom-up, non-linear model of the building and air conditioning system under control. We find that using a quadratic preference function for temperature can yield solutions that are both more comfortable and lower-cost than previous work that used a ``brick wall'' preference function with no preference for further cooling within an allowed temperature band and infinite aversion to going outside the allowed band. Using historical pricing data for a summer month in Chicago, CCPSO provided a 3\% reduction in costs vs. a ``brick-wall'' MPC approach with similar comfort and 13\% reduction in costs vs. a standard night setback strategy. CCPSO also reduced peak-hours demand by 3\% vs. the ``brick-wall'' strategy and 15\% vs. standard night-setback. At the same time, the CCPSO strategy increased off-peak energy consumption by 15\% vs. the ``brick-wall'' strategy. This may be valuable for power systems integrating large amounts of renewable power, which can otherwise become uneconomic due to saturation of demand during off-peak hours.

Anaerobic digestion is a biological process that transforms high-strength organic effluents into biogas with multiple benefits. However, concurrent with organics' biological transformation, a liquid phase with a high solid content is also derived from this process. Valorizing this fraction is not an easy task if an agronomic application cannot be considered as a suitable option. The thermal valorization of this fraction allows for energy extraction, but also gives rise to additional capital investment and increases the energy demand of the global process. In addition, the thermal treatment of digestate has to deal with a mineralized material. The changes in organic matter due to anaerobic stabilization were studied in the present manuscript, by evaluating the thermal behavior of samples, activation energy and organic transformation using FTIR spectroscopy. Digested samples of a mixture composed of manure and glycerin (5% v/v) were studied. The stabilization caused a dramatic decrease in aliphatic compounds, greatly increasing the mineral content of the sample. Thermal valorization of digestates must consider the lower energy content and more complex structure of these materials, with higher content of lignin and protein-type compounds.

The speed with which text can be read is determined in part by the spatial regularity and similarity of vertical letter strokes as assessed by the height of the first peak in the horizontal autocorrelation of the text. The height of this peak was determined for two passages in 20 fonts. The peak was unaffected by the size of the text or its content but was influenced by the font design. Sans serif fonts usually had a lower peak than serif fonts because the presence of serifs resulted in a more even spacing of letter strokes. There were small effects of justification and font- dependent effects of font expansion and compression. The visual comfort of images can be estimated from the extent to which the Fourier amplitude spectrum conforms to 1/f. Students were asked to adjust iBooks to obtain their preferred settings of font and layout. The preference was predicted by the extent to which the Fourier amplitude spectrum approximated 1/f, which in turn was jointly affected by the design of the font, its weight and the ratio of x-height to line separation. The above algorithms can be usefully applied to any orthography to estimate likely speed and comfort of reading.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Fission-track modelling rests on etching, counting and measuring the lattice damage trails from uranium fission. The tools for interpreting fission-track data are advanced but the results are never better than the data. Confined-track samples must be an adequate size for statistical analysis, representative of the track population, consistent with the model assumptions and with the calibration data. Geometrical and measurement biases are understood and can be dealt with up to a point. The interrelated issues of etching protocol and track selection are however more difficult to untangle. Our investigation favours a two-step protocol. The duration of the first step is inversely proportional to the apatite etch rate, so that different apatites etch to the same Dpar. A long immersion reveals many more confined tracks, terminated by basal and prism faces. This allows consistent length measurements and permits to orient each track relative to the c-axis. Long immersion times combined with deep ion irradiation reveal confined tracks deep inside the grains. Provided it is long enough, the precise immersion time is not important if the effective etch times of the selected tracks are calculated from their measured widths. Then, whether the sample is mono- or multi-compositional, we can, post hoc, select tracks with the desired properties. The second part of the protocol has to do with the fact that fossil tracks in geological samples appear to be under-etched compared to induced tracks etched under the same conditions. This should be assumed if the semi-axes (l_C, l_A) of a fitted ellipse plot above the induced-track line. In that case an additional etch can increase the track lengths to a point where they are consistent with the model based on lab-annealing of induced tracks, a condition for valid thermal histories. Here too, it is possible to select a subset with effective etch times consistent with the model if the widths of confined tracks are measured along with their lengths and orientations.

Falls at height are among the major causes of fatal accidents at work, especially in the construction sector. Maintaining balance while performing a tool with both hands generates physical efforts and mental loading that needs to be managed for workers’ safety and health. The purpose of the study is to compare perceived (dis)comfort (overall and localized), the ergonomic risk and the perceived effort through the acquired postures that subjects assumed during the execution of simple and common tasks both on a ladder and on the ground. 26 subjects were asked to perform four tasks in both conditions: top screwing, frontal screwing, object picking from the bottom forward, and object picking from the bottom sideways. Subjective and objective data were gathered for assessing subjective experience (discomfort and effort, perceived) and ergonomic risk. Results highlighted few ergonomic risk differences among “on ladder” and “on ground” tasks, while subjective data reveal significant differences in different scenarios. Main results regard knees and neck areas as the most critical ones.

The gravel road pavement has a lower construction cost but poorer performance than the asphalt surface. It also emits dust and deforms under the impact of vehicle loads and ambient air factors. The resulting ripples and ruts are constantly deepening, increasing vehicle vibrations and fuel consumption, reducing safe driving speed and comfort. In this article, existing pavement quality evaluation indexes are analysed, and a methodology for their adaptation for roads with gravel pavement is proposed. This article reports the measured wave depth and length of the gravel pavement profile by the straightedge method of a 160 m long road section in three road exploitation stages. The measured pavement elevation was processed according to ISO 8608, and vehicle frequency response has been investigated using simulations in MATLAB/Simulink. The applied International Roughness Index (IRI) analysis showed that a speed of 30-45 km/h instead of 80 km/h provides the objective results of IRI calculation on the flexible pavement due to a decreasing velocity of vehicle's unsprung mass on a more deteriorated road pavement state. The influence of the corrugation phenomenon of gravel pavement has been explored, identifying specific driving safety and comfort cases. Finally, an increase in the Dynamic Load Coefficient (DLC) at a low speed of 30 km/h on the most deteriorated pavement and a high speed of 90 km/h on the middle-quality pavement demonstrates the demand for timely gravel pavement maintenance and the complicated prediction of a safe driving speed for drivers.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

The development of the finite element method (FEM) combined block polynomial interpolation with the concepts of finite difference formats and the variation principle. Because of this combination, FEM overcomes the shortcomings of traditional variation methods while maintaining the benefits of current variation methods and the flexibility of the finite difference method. As a result, FEM is an advancement above the traditional variation methods. The aim of the study is to experimentally determine the thermal behavior of two stomatognathic systems, one control and the other presenting orthodontic treatment by means of a fixed metallic orthodontic appliance, both being subjected to several thermal regimes. In order to carry out this experimental study, we examined the case of a female subject, who was diagnosed with Angle class I malocclusion. The patient underwent a bimaxillary CBCT investigation before initiating the orthodontic treatment. A three-dimensional model with fully closed surfaces was obtained by using the InVesalius and Geomagic programs. Like the tissues examined in the patient, bracket and tube-like components, as well as orthodontic wires, can be included to these models. Once it is finished and geometrically accurate, the model is exported to a FEM-using program, such as Ansys Workbench. The intention was to study the behavior of two stomatognathic systems (with and without a fixed metallic orthodontic appliance) subjected to very hot food (70 ⁰C) and very cold food (-18 ⁰C). From the analysis of the obtained data, it was concluded that, following the simulations carried out in the presence of the fixed metallic orthodontic appliance, significantly higher temperatures were generated in the dental pulp.

Researchers are always looking to find ways to use energy more efficiently while keeping people comfortable at home. They've tried different methods like fuzzy logic and genetic algorithms to do this. In this paper, we introduce a novel model that combines different techniques like data smoothing, optimization, machine learning, and control algorithms to reach this goal in smart homes. The proposed model is made up of three main parts: smoothing, optimization, and control. The smoothing part uses the Kalman filter to get rid of any unnecessary noise and make sure the data used to predict energy use is clean and smooth. The optimization part uses both genetic with firefly algorithms and artificial neural networks to minimize the gap between the actual environmental conditions and the conditions users find comfortable. It adjusts the comfort settings in real-time using machine learning. The control part uses Mamdani fuzzy logic to make sure energy is delivered in the best way possible to the systems that control temperature, lighting, etc., making the home comfortable and saving energy at the same time. Comparative analyses demonstrate the superiority of the proposed model over existing algorithms, including the Particle Swarm Optimization (PSO) algorithm. Additionally, the paper discusses the importance of adaptive controllers in addressing issues associated with incorrect PID controller selection and highlights the benefits of using the FA-GA in energy optimization and comfort improvement. Overall, the proposed model offers an effective solution for efficient energy consumption optimization and enhanced user comfort in diverse settings through the integration of advanced algorithms and optimization modules.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

How much is religion quantitatively involved in global climate politics? After assessing the role of the Conference of Parties to the United Nations Framework Convention on Climate Change from a normative perspective, this descriptive, transdisciplinary and unconventional study offers the first comprehensive quantitative examination of religious nongovernmental organizations that formally participate in its annual meetings, the largest attempts to solve the climate crisis through global governance. This study finds that although their numbers are growing, only about 3 percent of registered nongovernmental organizations accredited to participate in the conference are overtly religious in nature — and that more than 80 percent of those faith-based groups are Christian. Additionally, this study finds that religious nongovernmental organizations that participate in the conference are mostly from the Global North. The results call for greater participation of religious institutions in the international climate negotiations in order for society to address the planetary emergency of climate change.

The pursuit of materials that offer both wear comfort and protection for functional and protective clothing has led to the exploration of weft-knitted spacer structures. Traditional cushioning materials such as spacer fabrics and laminated foam often suffer from deformation under compression stresses, thus compromising their protective properties. This study investigates the enhancement of the force absorption, stress-strain and thermal properties of weft-knitted spacer fabrics with inlays. Surface yarns with optimal stretchability and thermal properties are used and combined with elastic yarns in various patterns to fabricate nine different inlay samples. The mechanical and thermal properties of these samples are systematically analyzed, including their compression, stretchability, thermal comfort and surface properties. The results show that the inlay spacer fabric exhibits superior compression properties and thermal conductivity compared to traditional laminated foam and spacer fabrics, while maintaining stretchability, thus providing a better performance than traditional fabrics for protective clothing and wearable cushioning products. This study further confirms that the type of inlay yarn and inlay structure are crucial factors that significantly influence the thermal, tensile and compressive properties of fabric. This research provides valuable insights into the design and development of advanced textile structures to improve wear comfort and protection in functional garment applications.

Building energy consumption is the main urban energy consumption component, which mainly serves people-centered work and living energy demands. Based on the physical requirements of humans in urban buildings and to determine the comfortable body temperature in each season, this paper establishes a sizing optimization model of building-type integrated energy systems (IES), where the cooling and heating loads required to maintain indoor somatosensory body comfortable temperature are calculated. Depending on the external energy price, internal power balance and other constraints, the model develops an optimal sizing and capacity panning method of energy conversion and storage unit in a building-type IES with PV generation. The operating principle is described as follows: the PV generation is fully consumed, a gas engine satisfies the electric and thermal base load requirements, while the power system and a heat pump supply the remaining loads. The gas price, peak-valley electricity price gap and heat-topower ratio of gas engines are considered as important factors for the overall techno-economic analysis. The developed method is applied to optimize the economic performance of building-type IES and verified by practical examples. The results show that using the complementary characteristics of different energy conversion units is important to the overall IES cost.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

Regional Climatic Comfort Index (CCI) deteriorated significantly due to the climate change and anthropogenic interference. Knowledge regarding the long-term temporal dynamics of CCI in typical regions should be strengthened. In this study, we analyze the temporal and spatial evolution of CCI from 1969 to 2018 in Guangdong Province, based on meteorological indicators, including heat, humidity, wind and cloth loading etc.. Additionally, the population exposure to climate unconformity was examined since 1990 with the help of population data. Our study found that: (1) the warming and humidifying of the summer climate served as the main driving force for the continuous deterioration of CCI, with the comfortable days decreased by 1.06d/10a and the extremely muggy days increased by 2.83d/10a; (2) spatially, the lowest climate comfortability concentrated in southwestern Guangdong with more than 50 uncomfortable days each year, while the climate comfortability in northeastern Guangdong tends to deteriorated whit higher rate, which can reach as high as 6d/10a; (3) in summer, the population exposure to uncomfortable climate highly centralized in the Pearl River Delta, Shantou, Jieyang, and the surrounding areas, and both area and population exposure showed increasing trends. Particularly, Shenzhen held the highest growth rate of population exposure with an increase rate of 2.94 million/10a; (4) although the discomfort distribution and deterioration rate vary across the province, the spatial heterogeneity of comfortability is diminishing in Guangdong Province. This study will provide scientific reference for regional urban planning, thermal environment improvement, local resident health risk analysis, and key strategy implementation, etc.

Reinfection with severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) variants due to immune escape challenges the global response to the pandemic. We estimated the Omicron reinfection prevalence among people who had previous SARS-CoV-2 infections in Shanghai, China. We conducted a telephone survey in December 2022 for those who were previously infected with Omicron between March and May 2022. Information on demographics, coronavirus disease 2019 (COVID-19) testing, and vaccination history was collected. The overall and subgroup reinfection rates were estimated and compared. Among the 1981 respondents who were infected between March and May 2022, 260 had positive nucleic acid or rapid antigen tests in December 2022, with an estimated reinfection rate of 13.1% (95% confidence interval [95% CI]: 11.6-14.6). The reinfection rate for those who had a booster vaccination was 11.4% (95% CI: 9.2-13.7), which was significantly lower than that for those with an incomplete vaccination series (15.2%, 95% CI: 12.3-18.1) (adjusted odds ratio [aOR]: 0.579; 95% CI: 0.412–0.813). Reinfection with the Omicron variant was lower among individuals with previous SARS-CoV-2 infection and had completed a booster vaccination, suggesting that hybrid immunity can offer better protection against reinfection with Omicron sublineages.

The organic material present at the same depth in the reservoir has the potential for conversion, as indicated by analyses conducted before and after combustion in the development of heavy oil. This paper examines the oxidation and pyrolysis reaction pathways of hydrocarbons, specifically benzaldehyde (C₇H₆O) and naphthalene (C₁₀H₈), before and after combustion using molecular dynamics simulations. The primary products formed under various temperature conditions include H₂O, HO₂, CO, and CO₂. The discussion includes the number of molecules, such as HO and H, as well as their temperature variations. The activating group functions as an electron donor, while the inactivating group serves as an electron acceptor. The oxidation and pyrolysis reactions of naphthalene and the synthesis pathway of benzaldehyde are also explored. The C-C dissociation pathway in the early stages of combustion and the process of C-C bond synthesis in the later stages of the reactions are investigated through dynamic simulations at different temperatures: 3000 K, 3500 K, and 4000 K, with a particular focus on the reaction network at 4000 K. The application of the molecular reaction dynamics method to heavy oil combustion research is the primary objective of this work. This study aims to provide a novel approach to investigating hydrocarbon conversion at high temperatures and offers recommendations for enhanced oil recovery.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

This pioneering study explores the geospatial and temporal patterns of natural and human-induced disasters from 1900 to 2024, providing essential insights into their global distribution and impacts. Utilizing the comprehensive international EM-DAT database, our analysis reveals significant trends and disparities in disaster occurrences and their widespread consequences. Results showed a dramatic escalation in both natural and man-made (technological) disasters over the decades, with notable surges in the 1991-2000 and 2001-2010 periods. A total of 25,836 disasters were recorded worldwide, of which 69.41% were natural disasters (16,567) and 30.59% were man-made (technological) disasters (9,269). The most significant increase in natural disasters occurred from 1961-1970, while man-made (technological) disasters surged substantially from 1981-1990. Seasonal trends reveal that floods peak in January and July, while storms are most frequent in June and October. Droughts and floods are the most devastating in terms of human lives, while storms and earthquakes cause the highest economic losses. The most substantial economic losses were reported during the 2001-2010 period, driven by catastrophic natural disasters in Asia and North America. Our research highlights Asia as the most disaster-prone continent, accounting for 41.75% of global events, with natural disasters making up 61.89% of these events. Oceania, despite experiencing fewer total disasters, shows a remarkable 91.51% of these as natural disasters. Africa is notable for its high incidence of man-made (technological) disasters, which constitute 43.79% of the continent's disaster events. Europe, representing 11.96% of total disasters, exhibits a balanced distribution but tends towards natural disasters at 64.54%. Examining specific countries, China, India, and the United States emerged as the most frequently affected by both natural and man-made (technological) disasters. The impact of these disasters has been immense, with economic losses reaching their highest during the decade of 2010-2020, largely due to natural disasters. The human toll has been equally significant, with Asia recording the most fatalities and Africa the most injuries. Particularly, the decade from 2001 to 2010 experienced the greatest economic losses, primarily driven by natural disasters in Asia and North America. These insights highlight the urgent need for tailored disaster risk management strategies that address the distinct challenges and impacts in various regions. By understanding historical disaster patterns, policymakers and stakeholders can better anticipate and manage future risks, ultimately safeguarding lives and economies.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

Carbon fiber insole (CFI), which is lightweight and stiff to reduce energy loss and help wearers perform better in sports, has recently been introduced. However, there are scarce reports on the effects of CFI on sports performance, muscle fatigue and wearing comfort. This study investigat-ed the short-term effects of CFI on sports performance, lower extremity muscle activity, and sub-jective comfort. Thirty young healthy males performed various sports tasks and treadmill runs with wearable sensors under two experimental insole conditions (benchmark insole as a baseline, CFI). The results showed that compared to the benchmark insole, CFI significantly improved sports performance in terms of power generation and agility. However, it activated more of the Tibialis Anterior and Gastrocnemius Medialis muscles and was perceived stiffer, and less com-fortable. These findings suggested that CFI can improve sports performance, but it could cause more lower extremity muscle fatigue and subjective discomfort.

In order to enhance the comfort of cycling, it is imperative to investigate the effects of vibration on non-motorized bicycle riding from the perspectives of road characteristics and traffic features. Through an analysis of the mechanisms by which road and traffic conditions influence cycling vibrations, 13 influencing factors were identified. Subsequently, the non-motorized bicycle lanes in Wuhan city were selected as the subject of empirical research, where three-axis accelerometers attached to the rider's torso were employed to measure and categorize vibration comfort levels. The experimental road segments were found to exhibit comfort levels falling between slightly uncomfortable and relatively uncomfortable. Further analysis of the influencing factors was conducted using the Random Forest algorithm and Logistic Regression. The results revealed that six factors significantly impact the comfort of cycling: the presence of dedicated non-motorized bicycle lanes, the absence of physical separation between non-motorized and motorized traffic, cycling speed, the number of road surface irregularities, the presence of parking areas within the non-motorized bicycle lane, and the type of non-motorized bicycle. This study provides valuable insights into the factors affecting non-motorized bicycle lane usage and contributes to the refined design of urban non-motorized bicycle infrastructure, thereby facilitating better support for sustainable urban transportation.

In this paper, an in-wheel vibration absorber for In-wheel-motor electric vehicle (IWM EV) is designed, and a comprehensive control strategy of in-wheel absorber and vehicle suspension is proposed to improve vehicle ride comfort. The proposed in-wheel vibration absorber, designed for suppressing the motor vibration, is composed of a spring and a controllable damper. The values of in-wheel spring stiffness and damper initial coefficient are determined by using the improved particle swarm optimization (IPSO) algorithm, which is carried on the typical driving condition. To deal with the negative interaction effects between vehicle suspension and in-wheel absorber, the linear quadratic regulator (LQR) algorithm is utilized to control suspension damper, and the fuzzy PID method is utilized to control in-wheel damper. Based on the four evaluation indexes including vehicle body vertical acceleration, suspension dynamic deflection, wheel dynamic load and motor wallop, the simulation results show that, the proposed LQR control of suspension effectively improves vehicle ride comfort, and the fuzzy PID control of in-wheel damper exhibits superior performance of motor vibration suppressing in comparison to conventional electric wheel.

The research work explores the impact of temperature on Silicon photovoltaic (PV) panels considering Nigeria as case study. It is found that high solar radiation in Nigeria increases surface temperature of PV panel above 25oC of optimal operating temperature of PV panels. Redundant energy gain from incident solar energy is dissipated at the rear of PV panels as heat, which reduces the efficiency of PV panel. Cooling mechanism is needed to cool the PV panels to increase the efficiency. In this study we demonstrated a unique design of a bifunctional photovoltaic-thermal (PVT) system by employing heat exchanger at the rear of PV panel and water is used as a working fluid that is circulated through the heat exchanger to remove the excess heat. It is observed from the simulation results that Maiduguri peak annual electrical power output gives 1907kWh/kWp which is the highest, because of high solar radiation average of 727W/m2 in a year. And for Makurdi the peak annual electrical power output of 1542kWh/kWp while for Port Harcourt the peak power output of 1355kWh/kWp respectively. Interestingly, Polycrystalline Si-PV surface temperature decrease from 49.25oC to 38.38oC. Electrical power increased from 1526.83W to 1566.82W in a day and efficiency increase from 13.99% to 15.01%.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

A medium scale household in South Africa consumes about 1000 kWh on average, and ae household spend about 3000 ZAR per month on energy supply using grid electricity. Grid electricity. South Africa’s energy is supplied by a huge governmental organization. Statistical analyses indicate that projected increase of the cost of grid electricity in South Africa is about 30% per annum for the next five years. Our research show that Photo-Voltaic (PV) technology can offer a viable alternative, provided a large initial capital outlay can be made. The technology is user-friendly and easy to operate. It is calculated that the cost of electricity, capitalized over 20 years, considering an 80 % supply of needs and assuming 20 sunny days per month, is about 2.80 ZAR. The study also shows that utilizing a hybrid combination of renewable energies, such as combining PV supply with solar thermal energy absorbers, and converting thermal energy to electricity, as energy supply systems, could reduce the current cost of electricity per household in South Africa to about half of national grid supply prize, R1,50 per kWhr. The study also shows that water provides as a most viable medium to store energy, instead of using expensive battery technology to perform such functions.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

With the ever-growing emphasis on global decarbonization and rapid increases in the power density of electronics equipment in recent years, new methods and lightweight materials have been developed to manage heat load as well as interfacial stresses associated with Coefficient of Thermal Expansion (CTE) mismatch between components. The Al-Si system provides an attractive combination of CTE performance and high thermal conductivity whilst being a very lightweight option. Such materials are of interest to industries where thermal management is a key design criterion, such as aerospace, automotive, consumer electronics, defense, EV and space. This paper will describe the development and manufacture of a family of high-performance hypereutectic Al-Si alloys (AyontEX™) by a powder metallurgy method. These alloys are of particular interest for structural heat sink applications that require high reliability under thermal cycling (CTE of 17μm/(m·°C)) as well as reflective optics and instrument assemblies that require good thermal and mechanical stability (CTE of 13μm/(m·°C)). Critical performance relationships are presented, coupled with the microstructure, physical and mechanical properties of these Al-Si alloys.

The optimal combination of five components to develop a concrete for high-temperature applications was studied through a response surface methodology known as mixture design of experiment. The selected components were water, an alkali-activated binder based on ferronickel slag activated with potassium silicate and potassium hydroxide, and three aggregate sizes corresponding to 0-4 mm, 4-8 mm, and 8-16 mm. Selected response parameters were slump and compressive strength before and after heat exposure. Six cubes of side 150 mm were cast for each concrete mix, three for ambient and three for residual (post-heat exposure) compressive strength. All 20 concrete mixes were exposed to a thermal load of 600 °C for two hours. The optimal concrete mix was adapted for large-scale applications, by increasing slump and replacing limestone with olivine aggregates for enhanced residual compressive strength. The adapted mix resulted in concrete with 76 MPa and 32 MPa compressive strength before and after high-temperature exposure. The CO2 emissions were found to be 77 % lower when compared to traditional OPC concrete.

The present contribution introduces the task dependent comfort zone as a base placement strategy for mobile manipulators using different manipulability measures. Four different manipulability measures depending on end-effector velocities, forces, stiffness, and accelerations are considered. By evaluating a discrete subspace of the manipulator workspace with these manipulability measures and by using image processing algorithms, a suitable goal position for the autonomous mobile manipulator was defined within the comfort zone. This always ensures a certain manipulator manipulablity value with a lower limit in respect to the maximum possible manipulability in the discrete subspace. Results are shown for three different mobile manipulators using the velocity dependent manipulability measure in a simulation.

The semi-active cab suspension system for trucks is gaining increasing importance due to its economic advantages, low energy consumption, and significant enhancement of ride comfort. This paper investigates the effects of three control methods on improving ride comfort of semi-active cab suspension systems under random and bump road conditions: Proportional-Integral-Derivative (PID) control, fuzzy PID control, and Model Predictive Control (MPC). Initially, an accurate multi-degree-of-freedom truck cab suspension model was developed and validated through actual road tests. Based on this model, three control strategies were designed and implemented. Finally, the effectiveness of each control strategy was evaluated under various road conditions, including random and bump road scenarios. The results demonstrate that these control strategies can effectively reduce vibrations and impacts, significantly enhancing ride comfort, which is crucial for reducing driver fatigue and improving driving safety.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

Unmanned aerial vehicles (UAVs) represent a new model of social robots for home care of dependent persons. In this regard, this article introduces a study on people’s feeling of safety and comfort while watching the monitoring trajectory of a quadrotor dedicated to determining their condition. Three main parameters are evaluated: the relative monitoring altitude, the monitoring velocity and the shape of the monitoring path around the person (ellipsoidal or circular). For this purpose, a new trajectory generator based on a state machine, which is successfully implemented and simulated in MATLAB/Simulink®, is described. The study is carried out with 37 participants using a virtual reality (VR) platform based on two modules, UAV Simulator and VR Visualiser, both communicating through the MQTT protocol. The participants’ preferences have been a high relative monitoring altitude, a high monitoring velocity and a circular path. These choices are a starting point for the design of trustworthy socially assistive UAVs flying in real homes.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

Thermal infrared imagery provides temperature information on target objects, and has been widely applied in non-destructive testing. However, thermal infrared imagery is not always able to display detailed textures of inspected objects, which hampers the understanding of geometric entities consisting of temperature information. Although some commercial software has been developed for 3D thermal model displays, the software requires the use of expensive specific thermal infrared sensors. This study proposes a cost-effective method for 3D thermal model reconstruction based on image-based modeling. Two smart phones and a low-cost thermal infrared camera are employed to acquire visible images and thermal images, respectively, that are fused for 3D thermal model reconstruction. The experiment results demonstrate that the proposed method is able to effectively reconstruct a 3D thermal model which extremely approximates its corresponding entity. The total computation time for the 3D thermal model reconstruction is intensive while generating dense points required for the creation of a geometric entity. Future work will improve the efficiency of the proposed method in order to expand its potential applications to in-time monitoring.

Amphiphilic block copolymers of N-vinyl pyrrolidone (NVP) and various vinyl esters (VEs), PNVP-b-PVEs, namely vinyl butyrate (VBu), vinyl decanoate (VDc) and vinyl stearate (VSt) were synthesized by RAFT polymerization techniques. The sequential addition of monomers methodology was employed starting from the polymerization of NVP followed by the polymerization of the VEs monomer. The reaction was conducted at 80oC in dioxane solutions using AIBN as initiator and O-ethyl S-(phthalimidylmethyl) xanthate as the CTA. The block copolymers were characterized by Size Exclusion Chromatography (SEC) and NMR spectroscopy. The thermal transitions of the copolymers were studied by Differential Scanning Calorimetry (DSC), whereas their thermal stability via Thermogravimetric Analysis (TGA) and Differential Thermogravimetry (DTG).

The design and fabrication of low-cost catalysts for highly efficient oxygen reduction is of paramount importance for various renewable energy-related technologies, such as fuel cells and metal-air batteries. Herein, we report the in situ growth of Fe3N nanoparticles encapsulated N-doped carbon nanotubes on the surface of flexible biomass-derived carbon cloth (Fe3N@CNTs/CC) via a simple one-step carbonization process. Taking advantage of its unique structure, Fe3N@CNTs/CC was employed as a self-standing electrocatalyst for oxygen reduction reaction (ORR) and possessed high activity as well as excellent long-term stability and methanol resistance in alkaline media. Remarkably, Fe3N@CNT/CC can directly play the role of both gas diffusion layer and electrocatalytic cathode in a zinc-air battery without additional means of catalyst loading, and display higher open circuit voltage, power density, and specific capacity in comparison with the commercial Pt/C catalyst. This work is anticipated to inspire the design of cost-effective, easy-preparation, and high-performance air electrodes for advanced electrochemical applications.

High-Rise buildings with their particular features can affects on surrounding environment and makes new microclimates. In the windy conditions, the spaces that are between building blocks changes to passages and affects on the wind velocity, intensity and it’s other parameters.The importance of this effect is different in each level of building height. The Pedestrian-Level is the lowest and one of important areas. Markets, playgrounds and pedestrian access had located in this area and any unwanted microclimate changes like high velocity and turbulence in this level can makes discomfort and dangerous condition for residents. So this research tries to consider the pedestrian- level wind comfort in some High-Rise building complexes arrangement that had located in Tehran district 22 with Computational Fluid Dynamics (CFD) modeling and reaching to a suitable arrangement pattern. It had collected the required data through field study and librarian databases and then compared them with standard guidelines and analyzed them by comparative comparison method. As a result a linear arrangement that placed crossover to wind direction for providing wind comfort and preventing wind danger is been suggested in this region.

Conversion of electromagnetic energy into magnetohydrodynamic energy occurs when the electric conductivity changes from negligible to finite values. This process is relevant during the epoch of reheating of the early Universe at the end of inflation and before the emergence of the radiation-dominated era. We find that conversion into kinetic and thermal energies is primarily the result of electric energy dissipation and that the magnetic energy plays only a secondary role in this process. This means that, since electric energy dominates over magnetic energy during inflation and reheating, significant amounts of electric energy can be converted into magnetohydrodynamic energy when conductivity emerges early enough, before the relevant length scales become stable.

In this paper we establish information theoretical bridges between 1) Thermal Heisenberg uncertainties $\Delta x \Delta p$ (at temperature $T$), and 2) LMC structural quantifiers. After having achieved such purpose, we determine to what an extent our bridges can be extended to both the semi classical and classical realms. Also, we find a strict bound relating a special LMC structural quantifier to quantum uncertainties.

In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

In the quest for more efficient solar thermal systems, accurately determining the thermal emittance of low-emissive materials is crucial in determining the power losses. This paper describes the calorimetric method designed to precisely measure the thermal emittance of Selective Solar Absorbers (SSAs) to be used in High Vacuum Flat Plate Collectors (HVFPCs). The method's capability is demonstrated through the successful correction of thermal emittance values for copper samples of varying sizes, including dimensions down to 49 cm². Results highlight the method's potential to significantly reduce measurement errors associated with small-size and/or low-emittance samples, providing a path forward to improve the design and efficiency of SSAs. This research marks a significant step in advancing solar thermal technology by enabling emittance measurements with a precision better than 0.003, which is essential for the development of high-performance solar thermal absorbers. The method has also been applied to correct the thermal emittance value of SSA measured in previous measurement campaigns, and it allows a better estimation of the SSA efficiency conversion curve.

There are no studies that have investigated the characteristics of car use across THA patients, including those who do not drive. This study aimed to evaluate, in THA patients, (1) postoperative car usage, (2) comfort while entering and exiting a car, and (3) whether lower limb muscle strength affects action comfort. One hundred seventy-two post-THA patients completed the questionnaire in 2020, along with assessments of hip abductor and knee extensor muscle strength before surgery and at discharge. Patients whose overall comfort level was judged as “comfortable” were defined as the “comfort” group; others were placed in the “discomfort” group. Of the 172 patients, 161 reported car usage at a mean of 5.6 years after THA. Of these, 114 and 47 patients were placed in the "comfort" and "discomfort" groups, respectively. Patients in the "discomfort" group were three times more likely to experience discomfort using the contralateral side door than the surgical side door, and about twice as many patients experienced discomfort when entering as when exiting. Lower preoperative contralateral hip abductor muscle strength was the only independent predictor for discomfort. The take-home messages were that prevention of contralateral-side weakness may improve comfort during the action after THA.

Comprehensive understanding of tree characteristics and conditions holds paramount importance for the precise management of hazelnut orchards. It facilitates the determination of tree vigor, pruning requirements, phytosanitary interventions, and plant water consumption. The primary objective of this study was to explore, for the first time on a fruit tree with a bushy structure and across trees of four Italian distinct hazelnut cultivars, the efficacy of multispectral and thermal UAV (Unmanned Aerial Vehicle) technologies in assessing canopy attributes, vegetative growth, and predicting abiotic stresses. These technologies serve as tools for precision agriculture, enabling the computation of various indices such as the Normalized Difference Vegetation Index (NDVI) and crop water stress index (CWSI). The study of water content is of particular importance at this time, especially considering the increasing water stress levels in Europe as well as globally. While Red Green Blue (RGB) and thermal imagery collectively demonstrated superior performance in model reconstruction, the multispectral UAV remained more adept at characterizing size traits of hazelnut plants. Thermal images alone proved inadequate for accurately reconstructing hazelnut biometric characteristics. Furthermore, all indices were found to be cultivar-specific, underscoring the importance of conducting studies across different cultivars. The utilization of two UAVs, namely multispectral and thermal, facilitated the examination of the relationship between NDVI and CWSI across tree species.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Considering animal welfare, the free-range laying hen farming model is increasingly gaining attention. However, in some countries, large-scale farming still relies on the cage-rearing model, making the focus on the welfare of caged laying hens equally important. To evaluate the health status of caged laying hens, a dataset comprising visible light and thermal infrared images was established for analyses, including morphological, thermographic, comb, and behavioural as-sessments, enabling a comprehensive evaluation of the hens' health, behaviour, and population counts. To address the issue of insufficient data samples in the health detection process for indi-vidual and group hens, a dataset named BClayinghens was constructed containing 61,133 images of visible light and thermal infrared images. The BClayinghens dataset was completed using three types of devices: smartphones, visible light cameras, and infrared thermal cameras. All thermal infrared images correspond to visible light images and have achieved positional alignment through coordinate correction. Additionally, the visible light images were annotated with chicken head labels, obtaining 63,693 chicken head labels, which can be directly used for training deep learning models for chicken head object detection and combined with corresponding thermal infrared data to analyze the temperature of the chicken heads. To enable the constructed deep-learning object detection and recognition models to adapt to different breeding environ-ments, various data enhancement methods such as rotation, shearing, colour enhancement, and noise addition were used for image processing. The BClayinghens dataset is important for ap-plying visible light images and corresponding thermal infrared images in the health detection, behavioural analysis, and counting of caged laying hens under large-scale farming.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.