Coal bottom ash (CBA) is a byproduct of coal-burning power plants. This material can be used as a fine aggregate replacement in concrete to reduce global natural material depletion. Concrete usage is increasing rapidly; subsequently, the industry’s carbon footprint is increasing. Using CBA in the construction industry will reduce the technical and economic problems associated with power plants by reducing solid waste. This project aimed to determine if adding new sustainable materials, such as CBA, to concrete will reduce natural raw material usage, energy consumption, and greenhouse gas emissions while improving performance. This study included two projects: comparing increased CBA content to the two-control project and determining the optimum content based on the compressive strength. The optimum CBA content is 50%, which reduces fine aggregate usage in a concrete mix by 50% while maintaining equivalent or better concrete strength than a pure Portland concrete mix without CBA. The air content of the concrete mix containing % CBA decreased with increased CBA content and compressive strength, possibly due to the spacing factor of the voids in the mix and CBA’s porous and fineness behavior. The CBA optimum content had a unit weight lower than the controls for both projects, which makes the CBA mix a lightweight concrete. Using this material can significantly reduce natural material usage and environmental harm by reducing CBA waste disposal and improving concrete performance.

Cement production requires a significant amount of energy and natural resources, severely impacting the environment due to harmful gas emissions. Coal Bottom Ash (CBA) and Coal Boiler Slag (CBS), byproducts of coal-fired power plants, have pozzolanic properties. CBA and CBS can be mechanically ground to obtain Ground Coal Bottom Ash (GCBA) or Ground Coal Bottom Slag (GCBS), which can potentially replace cement in concrete, reducing waste in landfills, benefit the economy, preserving natural resources, and reducing health hazards. This study was performed to determine the optimum amount of GCBA and GCBS that can replace cement in concrete. The fresh, mechanical, and durability properties of the concrete containing GCBA were compared to a control mix consisting of 100% Portland cement. The optimum amount of cement replaced with GCBA and GCBS was 10% and 5%, respectively, based on compressive strength. The GCBA-based concrete's tensile strength, modulus of elasticity, and durability properties were better than the control. The compressive strength of the GCBA and GCBS-based mortars increased with an increase in fineness. GCBA and GCBS fineness should be within the limit recommended in the ASTM C618 standard to enhance concrete or mortar properties.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Two secondary waste materials, municipal incinerator bottom ash (MIBA) and sewage sludge ash (SSA), were mixed with clay for ceramic manufacturing in this study. Specimens with 5 different MIBA replacement amount of 0%, 5%,10%, 15%, and 20%(wt) and 3 different SSA replacement amount of 0%, 10%, and 20%(wt) were prepared and then a series of tests and analysis were conducted to investigate how the two materials affect the quality of the final product and to what extent. It concludes that a mix with up to 20% of SSA and 5% of MIBA could result in quality tiles complying with specifications for interior or exterior flooring applications at certain kiln temperatures.

In this research, the feasibility of using bottom ashes generated by the combustion of biomass (olive pruning and pine pruning) as a source of aluminosilicates (OPBA) has been studied, replacing the metakaolin precursor (MK) in different proportions (0, 25, 50, 75 and 100 wt. % substitution) for the synthesis of geopolymers. As alkaline activator an 8 M NaOH solution and a Na2SiO3 have been used. The geopolymers were cured 24 hours in a climatic chamber at 60 ° C in a water-saturated atmosphere, subsequently demoulded and cured at room temperature for 28 days. The results indicated that the incorporation of OPBA waste, which have 19.7 wt. % of Ca, modifies the characteristics of the products formed after alkaline activation. In general terms, the incorporation of increasing amounts of calcium-rich ashes results in geopolymers with higher bulk density. The compressive strength increases with the addition of up to 50 wt. % of OPBA with respect to the control geopolymers, contributing the composition of the residue to the acquisition of a better behaviour mechanical. The results indicate the potential use of these OPBA waste as raw material to produce unconventional cements with 28-day curing strengths greater than 10 MPa, and thermal conductivities less than 0.35 W/mK.

The separation and enrichment can be targeted to enrich the rare and precious metals in fly ash and reduce the cost of leaching and recovering of fly ash. Regarding their different properties, the single-component separation was used to obtain uncompleted burned carbon, glass microbeads, minerals, and other characteristic components from the ash. Also, the mineral composition of each component was analyzed by electron microscopy. The metal minerals were mainly concentrated in the mineral components. Besides, the electron probe micro-analysis shows that the Pt content in the minerals of fly ash was significantly correlated with the metal contents of Ni and Cu. After the obtainment of the characteristics of fly ash metal enrichment, the heavy minerals with Cu, Ni, Pt, Pd, and other target metal elements were enriched by gravity separation and flotation. The enrichment coefficients of Cu, Ni, Pt, and Pd were 1.45, 1.33, 1.90 and 1.60, respectively, and the recovery rates were 77%, 81%, 97% and 88% respectively. Since the yield of heavy minerals obtained by separation was 62.24%, it indicated the physical separation method could significantly reduce the cost of leaching and recovering of fly ash metal resources.

This study aimed at characterizing the composition and performing chemical speciation modelling to determine species that are abundant in the coal fly ash (CFA) and soil samples sourced from Hendrina Power station located in Mpumalanga Province. All CFA samples were alkaline in nature with pH values ranging between 8.11 ± 0.07 and 8.60 ± 0.03 with an electrical conductivity (EC) ranging between 301.70 and 1515.00 µS/cm while EC of control soil was 103.10 µS/cm. The control soil pH was found to be 6.24 ± 0.13 and total organic carbon values ranged between 2.68 and 85.82 mg/kg and some percentage organic carbon values of CFAs were found to be greater than 8%, which is above the permissible limits of hazardous waste dumping. Oxidation-reduction potential values were negative in all CFA samples and positive in soil. The speciation modelling showed that the potential for a trace metal to have hazardous effects in soil systems depends on its concentration, specific form and interactions with other constituents in CFA. The slow release of metals from CFA to soil was assessed by looking at how a given metal is distributed throughout its several possible chemical forms. The presence of divalent cations (Pb2+, Cu2+, Zn2+, etc.) in CFAs might pose a threat to soil quality. In the competition for binding sites on ferric hydroxides, dissolved metal ions faced off against other metals. Protons (H+) were seen to be in competition with Pb, Cu and Zn for the ability to bind to hydroxyl (OH-) groups and this is due to chemical precipitation and surface complexation.

Generating electricity from coal combustion is highly associated with ongoing pollution problems that negatively impact the environment. Coal fly ash (CFA) is a predominant waste by-product of coal combustion which is disposed of in exposed ash dams constructed in the vicinity of power stations. Its disposal requires a large piece of land and therefore more land is converted to unproductive disposal sites, degrading the ecosystem. This waste material is classified as a hazardous substance in South Africa due to unacceptable levels of inorganic and persistent organic pollutants and its potential for dust creation. CFA is recycled and sold to the building and construction sectors, but the rate of its utilization is far less than the production rate resulting to high volumes that is stockpiled in disposal sites. More than 500 million tons CFA is produced yearly and over 200 million tons yearly remain unused globally and more CFA will continue to be produced due to high consumer energy demands, especially in countries with heavy reliance on coal for power generation. In this context, the paper discusses production of CFA, pollution problems due to its disposal, examines existing gaps within the scope of ash dam restoration processes and presents opportunities offered by phytoremediation (a low-cost and environmentally friendly technology that utilizes plants to restore the degraded environments). Ecological restoration through the use of socio-economically valuable plants (aromatic plants, legumes and grasses) has potential in addressing societal challenges and consequently impacting positively the livelihood of communities.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.

The production of municipal solid waste incineration bottom ash (MSWIBA) is very massive and has the potential to replace cement despite the problems of complex composition, uneven particle size distribution, and low reactivity. This paper adopts sodium silicate activation of MSWIBA-slag to improve the reactivity to prepare composite cementitious materials. It explores the hydration performance study of the composite cementitious materials by isothermal calorimetric analysis, Fourier Transform Infrared (FTIR) spectroscopy, XRD physical diffraction analysis, and SEM/EDS tests. SEM/EDS tests will be used to explore the hydration properties of the composite gelling. The results showed that with the increase of MSWIBA doping, the porosity between the materials increased, the degree of Hydration decreased, and the compressive strength decreased with the rise of MSWIBA. When sodium silicate increased from 25% to 35%, too much alkaline material occurred over the alkaline effect, which inhibited the Hydration of the particles, and the degree of hydration reaction decreased, and the compressive strength decreased accordingly; the exothermic process of Hydration can be mainly divided into five stages, quartz and calcite did not participate in the hydration reaction completely, and sexual aluminum participated in the hydration reaction. The vibrational peaks of Si-O-Ti (T = Si and Al) were present in the material. The vibrational peaks of XRD, FTIR, and SEM-EDS all indicate the presence of silica-aluminate network structures in the hydration products, mainly N-A-S-H and C-A-S-H gels.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

The orbital elactronic structure of Rare Earth Elements (REEs) contains many unpaired electrons which render them capable of storing large amount of magnetic energy in addition to being critical for hitech applications. Geological deposits are their conventional sources, and the current supply chain relies on production from these deposits. However, given their critical roles in the anticipated global energy transition, there is the need to explore other viable sources to supplement current and future supplies chains. REEs occur in coal as accessory minerals and their concentration in coal ash to levels that rival those of geological deposits has been estab;ished by sophisticated analytical chemical methods. Conmventional hydrometallurgical processes rely on acid leaching, using tioxic mineral acids. Meanwhile, organosulfonic acids have pKa values that rival those of conventional minerals acid and can, therefore, be used in hydrometallurgy but their uses in this regard are not well documented in the literature. In this extensive review, we have covered geological sources of REEs exaustively in addition to showing the potential of organosulfonic acids as environmentally benign lixiviants for REEs extraction from coal ash. We have also shown how process optimization can be achieved using advance technologies while using organisulfonic acids. Moreover, we have shown current and future global market trends regarding the production of select organosulfonic acids, and the anticipated global increase in their production motivates the use of organosulfonic acids as viable lixiviants for REEs extraction from caol ash deposits.

The use of cemented aeolian sand-fly ash backfill (CAFB) material to fill the mining area to improve the surface subsidence damage caused by underground coal mining is in the development stage. Their performance with large overflow water and strength loss is not well understood. Few research has been conducted to understand the effects of aeolian sand and coal gangue on the rheological properties of CAFB with plasticizers. Therefore, the aim of this study is to investigate the effects of a plasticizer on the rheological properties, specifically yield stress and viscosity, of CAFB prepared with aeolian sand and coal gangue. CAFB mixes containing 0%, 0.05%, and 0.1% plasticizer were prepared, and yield stress and viscosity were determined at different time intervals over the period. Additional tests, such as thermal analysis and zeta potential analysis were also conducted. It was found that the rheological properties of CAFB is the comprehensive manifestation of the composite characteristics of various models. Reasonable particle size distribution and less amount of plasticizer can ensure the stability of slurry structure, reduce the slurry settlement and the risk of pipe blocking. The findings of this study will be beneficial in the design and production of CAFB material.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

This study evaluated the physicochemical, mineralogical properties, mobile chemical species’ bioavailability and translocation in Brassica juncea and Spinacea oleracea L plants of a South African coal fired power utility. Coal fly ash (CFA) disposal is associated with various environmental and health risks including air, soil, surface and ground water pollution due to the leaching of toxic chemical species; these ends up in food webs affecting human health, while repeated inhalation causes bronchitis, silicosis, hair loss and lung cancer. The morphology, chemical, and mineralogical composition of CFA were determined using Scanning Electron Microscopy (SEM), X-ray fluorescence (XRF) and X-ray Diffraction, respectively. In pot culture experiments, S. oleracea L and B. juncea plants were grown in three sets of pots containing CFA (set 1), soil (set 2) and a mixture of CFA plus soil at ratio 1:1 (50% CFA: 50% soil) (set 3), while no plants were grown in set 4 as a control for the leachate samples. SEM showed that surface morphology of CFA has a lower degree of sphericity with irregular agglomerations of many particles. The XRF results revealed that CFA contains 43.65%, 22.68% and 10.89% of SiO₂, Al₂O₃ and Fe₂O₃ respectively which indicate that the CFA is an alumino-silicate material. While XRD showed that the coal CFA contains mullite as a major phase followed by quartz mineral phases. Chemical species such as Fe, Mn, B, Ba and Zn were accumulated highly in most parts of the plant species. However, B. juncea showed higher potential to accumulate chemical species as compared to S. oleracea L. The bioconcentration and translocation factors (BF and TF) showed that B. juncea was the most effective in terms of bioconcentration and translocation of most of the chemical species. This indicates that B. juncea has potential in application for phytoremediation of CFA dumps and could contribute to remediation of CFA dumps and reduction of potential health and environmental impacts associated with CFA.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

The static formation temperature (SFT) is required to determine the thermophysical properties and production parameters in geothermal and oil reservoirs. However, the SFT is not easy to be obtained by both experimental and physical methods. In this paper, a mathematical approach to predicting SFT based on a new model describing the relationship between bottom hole temperature (BHT) and shut-in time was proposed. The unknown coefficients of the model were derived from least squares fit by Particle Swarm Optimization (PSO) algorithm. Besides, the ability to predict SFT based on a few BHT data (such as first 3, 4, or 5 ones of a data set) was evaluated. The accuracy of the proposed method to predict SFT was testified with a deviation percentage less than ±4% and high values of regression coefficient R² (>0.98). The proposed method could be used as a practical tool to predict SFT in both geothermal and oil wells.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Background: Wheat root rot disease due to soil-borne fungal pathogens leads to tremendous yield losses worth billions of dollars worldwide every year. It is very important to study the relationship between rhizosphere fungal diversity and wheat roots to understand the occurrence and development of wheat root rot disease. Results: A significant difference in fungal diversity was observed between the diseased and healthy groups in the heading stage, but the trend was the opposite in the filling stage. The abundance of most genera with high richness decreased significantly from the heading to the filling stage in the diseased groups; the richness of approximately one-third of all genera remained unchanged, and only a few low-richness genera, such as Fusarium and Ceratobasidium, had a very significant increase from the heading to the filling stage. In the healthy groups, the abundance of most genera increased significantly from the heading to the filling stage; the abundance of some genera did not change markedly, or the abundance of very few genera increased significantly. Physical and chemical soil indicators showed that low soil pH and density, increases in ammonium nitrogen, nitrate nitrogen and total nitrogen contributed to the occurrence of wheat root rot disease. Conclusions: Our results revealed that in the early stages of disease, highly diverse rhizosphere fungi and a complex community structure can easily cause wheat root rot disease. The existence of pathogenic fungi is a necessary condition for wheat root rot disease, but the richness of pathogenic fungi is not necessarily important. The increases in ammonium nitrogen, nitrate nitrogen and total nitrogen contributed to the occurrence of wheat root rot disease. Low soil pH and soil density are beneficial to the occurrence of wheat root rot disease.

The physical properties of coal reservoirs are the main restrictions to exploration and development of CBM. The study of the physical characteristics of coal reservoirs and their controlling factors is of great significance to the safe and efficient development and utilization of CBM resources in the mining area. The Pingdingshan No. 10 coal mine was chosen for this study because of its better gas production effect at the test wells. The reservoir properties of the main coal seams of the No. 10 coal mine were tested and analyzed to comprehensively evaluate the reservoir properties. The results indicate that (1) The gas content and methane purity of the No. 4 coal seam are significantly higher than the No. 2 seam, and therefore they have better development potential than the No. 2 seam; (2) The average adsorption time of the No. 2 coal seam is less than that of the No. 4 seam, making it easier to reach the peak production capacity of CBM wells in the short term, but is not conducive to long-term stable production of CBM. The Langmuir volume of the No. 2 coal seam samples was significantly greater than for the No. 4 coal seam; however, the No. 4 coal seam contains about three times the amount of gas in the No. 2 seam; (3) All three coal seams have high porosity, which is favorable for large amounts of CBM adsorption and storage. Micropores predominate, transitional pores are less frequent, and a few mesopores occur; macropores are the least common. Samples from the No. 4 seam contained the highest proportion of micropores; (4) Organic pores were common in the all coal samples, with pore diameters not more than 30 µm, mainly concentrated between 50.5 and 1000 nm. Microfractures with aperture less than 70 nm were relatively frequent, mainly in the 50–65 nm range. A large number of the nanoscale microfractures were curved or jagged; (5) Fractures in the No. 2 and No. 4 coal seam samples with widths of 50 nm to 20 µm were more developed, and many were filled with kaolinite, quartz and other minerals; (6) The samples contained mostly layered silicate minerals (kaolinite), with hard granular minerals (quartz) next, and a very small quantity of iron-type minerals such as siderite and pyrite in dendritic form. The results of this study can provide a reference basis for the large-scale development and utilization of subsequent CBM wells.

The hydrodynamics of plasma formed in the interaction of 100-ns UV KrF laser pulses with foam targets with volume densities from 5 to 500 mg/cm3 was studied. Initial and dynamic transmittance at 248-nm wavelength have been measured. At intensities about 1012 W/cm2, the propagation rates of radiation through foam targets reached 80 km/s, while plasma stream velocities from both front and rear sides of targets were approximately the same ~ 75 km/s, which confirms a volumetric absorption of radiation within the target thickness and the explosive nature of the plasma formation and expansion.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

No doubt pollution is a global problem which must be holistically tackled. In doing this, adequate knowledge of the sources of pollution is important, therefore the aim of this paper is to review source apportionment with reference to top-down and bottom-up methods. In this paper, dispersion modeling, emissions inventory, and sampling methods were discussed. Also, analytical methods involved in top-down source apportionment were mentioned. The two techniques are needed to evaluate pollutants and their sources. Based on these two approaches, pollution control strategy would be developed and decisions can be made in deciding the right approach to solve or reduce the pollution problems.

The present decade has witnessed numerous investigations focussed on the determination of the mechanical properties of Fly ash composites. These composites have attracted attention, especially in the form of reinforcements owing to their excellent tensile and compressive properties coupled with impact and hardness response. A number of techniques viz. in-situ deposition, hand-up lay and compo-casting techniques have been reported to fabricate these composites. However, in the context of these composites, a systematic structure-property correlation has not been established till date. The present review is aimed at highlighting the current state of research in the avenue of Fly ash composites from two different viewpoints, viz. (i) fabrication technique and (ii) mechanical properties of the fabricated composites. Moreover, the necessity of establishing systematic structure-property correlation in these materials has also been briefly discussed from the author’s viewpoint.

The neural system has limited resources to interact with the environment, and this is where attention comes into play. Attention is a complex process that provides numerous benefits, but there has been a longstanding debate about the mechanisms involved in attentional orientation. Two widely proposed mechanisms are top-down and bottom-up, which relate to the organism's current behavioral goal and the salience of environmental stimuli, respectively. However, distinguishing between these mechanisms can be challenging in both behavioral and neural studies. This review introduces a new conceptualization in which both top-down and bottom-up mechanisms are viewed as aspects of the same process. This unified approach aims to prepare the organism to face stimuli and events based on its prior experiences, immediate (the current task that he/she is aware of), and innate (to be alive) demands.

Serious damage caused by floor heave in the coal given chamber of a vertical coal bunker is one of the challenges faced in underground coal mines. Engineering practice shows that it is more difficult to maintain the coal given chamber (CGC) than a roadway. More importantly, repairing the CGC during mining practice will pose major safety risks and reduce production. Based on the case of the serious collapse that occurred in the bearing structure of the CGC at the lower part of the 214# coal bunker in Xiashijie mine, China, this work analysed (i) the main factors influencing floor heave and (ii) the failure mechanism of the load-bearing structure in the CGC using FLAC^2D numerical models and expansion experiment. The analysis results indicate that: the floor heave, caused mainly by mine water, is the basic reason leading to the instability and repeated failure of the CGC in the 214# coal bunker. Then a new coal bunker, without building the CGC, is proposed and put into practice to replace the 214# coal bunker. The FLAC^3D software program is adopted to establish the numerical model of the wall-mounted coal bunker (WMCB), and the stability of the rock surrounding the WMCB is simulated and analysed. The results show that: (1) the rock surrounding the sandstone segment is basically stable. (2) The surrounding rock in the coal seam segment, which moves into the inside of the bunker, is the main zone of deformation for the entire rock mass surrounding the bunker. Then the surrounding rock is controlled effectively by means of high-strength bolt–cable combined supporting technology. According to the geological conditions of the WMCB, the self-bearing system, which includes (i) H-steel beams, (ii) H-steel brackets, and (iii) self-locking anchor cables, is established and serves as a substitute for the CGC to transfer the whole weight of the bunker to stable surrounding rock. The stability of the new coal bunker has been verified by field testing, and the coal mine has gained economic benefit to a value of 158.026174 million RMB over three years. The new WMCB thus made production more effective and can provide helpful references for construction of vertical bunkers under similar geological conditions.

This paper deals with investigation of changes in geopolymer wettability with increasing mass fraction of high-carbon fly ash and surface treatment by cold atmospheric plasma (CAP). In this study, multiple samples of geopolymers were prepared, including those with 5% and 10% of high-carbon fly ash from coal-fired power station. Wettability of samples was then measured before and after plasma treatment, both on surface and cut surface. While addition of fly ash only had low effect on the wettability, as in most cases, it only lowered the initial contact angle without speeding up the speed of soaking for compact geopolymer and actually slowed the soaking for foamed geopolymer, plasma treatment had significant impact and made the geopolymer hydrophobic.

Nonlinear compression of narrow-band (Δ ≈ 0.2 cm-1) 20 ns KrF laser pulses in SF6 at 10 atm and CH4 at 50 atm pressure was studied. Both SBS and SRS optically phase conjugated backward reflected radiation was registered with energy reflectivity 10−14% in SF6 and CH4. In SF6 SBS pulses gradually shortened from 10 ns to 2−3 ns with pumping decrease to the SBS threshold ~ 10 mJ, while the SRS pulse had the shortest length of 30−60 ps for the maximal pumping of 120 mJ and broadened near the SRS threshold of ~30 mJ. For the SRS pulse energy ~ 2 mJ peak power 5×107 W was tenfold higher than the pump power. The theoretical model predicted a soliton-like SRS pulse compression to a temporal length of the order of vibrational relaxation time. There was no pulse compression of backward SBS and SRS radiation in CH4, while in the forward direction SRS pulses shortened to 3−4 ns at reduced pumping.

An analysis of the stiffness theory reveals that coal mass compression bumps occur only when both the failure criterion and the stiffness criterion are simultaneously satisfied. Then a new structural factor called uneven stiffness coal seam structure (USCS) is proposed, which consists of an uneven stiffness coal seam along with continuous roof and floor. The USCS serves the dual functions of pressure concentration and stiffness reduction. The former facilitates stress concentration from the low stiffness zone (LSZ) to the high stiffness zone (HSZ), thus raising the risk (rF) of failure. The latter reduces the stiffness of the surrounding rock of the HSZ, allowing the system to meet the stiffness criterion even with a hard roof, thereby reconciling the contradiction between the stiffness theory and engineering experience and raising the risk (rI) of instability. The HSZ of the USCS, including thinning zones, bifurcating areas, magmatic intrusion areas, and remnant pillar affected areas, is more susceptible to coal bump incidents than a conventional coal seam. Mechanical analysis and simple numerical simulations validate the pressure concentration and stiffness reduction functions of the USCS. The results demonstrate the following: 1) The normal stress of the HSZ positively correlates with ER, HR, KH, and SL, but negatively correlates with KL and SH; The stiffness of surrounding rock of the HSZ negatively correlates with HR, KH, SL, and SH, but positively correlates with ER and KL. 2) Failures within the HSZ of the USCS enables the roof strata to release bending deformation energy without undergoing fracturing. 3) The alignment between the HSZ of an existing USCS and the HSZ of an artificial USCS advancing with the working face intensifies stress concentration and reduces stiffness, thereby significantly increases the risk (rCB) of coal bump. By applying the stiffness theory and relevant USCS findings, new explanations can be provided for engineering phenomena such as the time-delayed coal bumps, the inefficient pressure relief in ultra thick coal seams, and the “microseism deficiency” observed prior to certain coal bumps.

This paper presents a new broadband ocean bottom seismograph (OBS) developed by the SUSTech OBS lab for passive-source seafloor seismic observations. This instrument, called Pankun, has several key features that set it apart from traditional OBS instruments. Besides the seismometer-separated scheme, these features include a unique shielding structure to minimize current-induced noise, a compact gimbal for accurate leveling, and low power consumption for extended operation on the seafloor. The design and testing of Pankun's primary components are thoroughly described in the paper. The instrument has been successfully tested in the South China Sea, demonstrating its ability to record high-quality seismic data. The anti-current shielding structure of Pankun OBS has the potential to improve low-frequency signals, particularly on the horizontal components, in seafloor seismic data.

This study presents preliminary findings on the physicochemical, calorific, and thermal properties of a newly discovered coal from Obomkpa town in Aniocha-North Local Government Area of Delta State in Nigeria. The Obomkpa (BMK) coal sample was subjected to fuel characterisation through ASTM standards and techniques for determining elemental, proximate, and calorific coal properties. The results indicated that BMK coal contains high carbon, oxygen, volatile matter, fixed carbon, and ash. The higher heating value of BMK was 19.66 MJ/kg, which indicates it could be ranked as either lignite A or subbituminous C coal. The thermal properties indicated that BMK experienced significant mass loss (M_L) under oxidative (combustion) and non-oxidative (pyrolysis) conditions due to thermal degradation of organic rock macerals (inertinite and vitrinite). Furthermore, BMK experienced mass loss (M_L=59.27%–76.56%) along with residual mass (R_M = 23.44–40.73%) under oxidative (combustion) and non-oxidative (pyrolysis) conditions. Thermal degradation occurred in three (3) stages; drying (30 °C to 200 °C), devolatilization (200 °C – 500 °C and 600 °C), and lastly, coke degradation and ash formation. Furthermore, the DTG peaks for the drying and devolatilization of BMK during the oxidative (combustion) process occurred at lower temperatures compared to the non-oxidative (pyrolysis) process. Hence, the results submit oxidative (combustion) is a more thermally efficient process compared to the non-oxidative (pyrolysis) process. Lastly, the findings indicate BMK is a potential feedstock material for future coal power generation, steel, iron ore or cement production.

Coal currently accounts for over 38% of electric power generation around the globe. Hence, it is a significant critical contributor to socio-economic growth and development, particularly in the BRIC economies. The success of the coal energy in these nations in addition to the discovery of vast new coal deposits have revived Nigeria’s interest in coal power. However, there is lack of comprehensive data on the pollution emission profiles, along with the physicochemical, thermal, and kinetic properties of Nigerian coals as required for power plant operations. Therefore, this paper presents preliminary findings on the physicochemical, microstructural, mineralogical and thermal properties of Owukpa (WKP) coal from Benue State in Nigeria. The results showed that WKP contains high compositions of combustible elements and heating value but low pollutant elements. Furthermore, thermal degradation revealed high conversion efficiencies particularly under oxidative conditions as required for electric power generation through combustion.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

Mediterranean Ridge accretionary complex (MAC) is one of the most critical subduction zones in the world. It is known that the region exhibits a continuous mass change (horizontal/vertical movements). This process is associated with the devastating and tragic earthquakes shaking the MAC for centuries. Here, we investigate the ocean bottom pressure (OBP) anomalies in the MAC derived from the Gravity Recovery and Climate Experiment (GRACE) and GRACE Follow On (GRACE-FO) satellite missions. The OBP time series for the MAC comprises a decreasing trend in addition to 1-, 1.53-, 2.36-, 3.67-, and 9.17-year periodic components partially explained by the atmosphere, oceans, and hydrosphere (AOH) processes, and Earth's pole movement. We noticed that the OBP anomalies appear to link to a rising trend and periods in earthquakes' power time series. This finding sheds new light on the mechanisms controlling the most destructive natural hazard.

Smart grids require flexible data driven forecasting methods. We propose clustering tools for bottom-up short-term load forecasting. We focus on individual consumption data analysis which plays a major role for energy management and electricity load forecasting. The two first sections are dedicated to the industrial context and a review of individual electrical data analysis. We are interested in hierarchical time-series for bottom-up forecasting. The idea is to disaggregate the signal in such a way that the sum of disaggregated forecasts improves the direct prediction. The 3-steps strategy defines numerous super-consumers by curve clustering, builds a hierarchy of partitions and selects the best one minimizing a forecast criterion. Using a nonparametric model to handle forecasting, and wavelets to define various notions of similarity between load curves, this disaggregation strategy applied to French individual consumers leads to a gain of 16\% in forecast accuracy. We then explore the upscaling capacity of this strategy facing massive data and implement proposals using R, the free software environment for statistical computing. The proposed solutions to make the algorithm scalable combines data storage, parallel computing and double clustering step to define the super-consumers.

Pore-fractures network play a key role in coalbed methane (CBM) accumulation and production, while the impacts of coal facies on the pore-fractures network performance are still poorly understood. In this work, the research on the pore-fracture occurrence of 38 collected coals from Sangjiang-Muling coal-bearing basins with multiple techniques including mercury intrusion porosimetry (MIP), micro-organic quantitative analysis, and optic microscopy, and its variation controlling of coal face were studied. The MIP curves of 38 selected coals indicating pore structures were subdivided into three typical types including type I of predominant micropores, type Ⅱ of predominant micropores and macropores with good connectivity and type Ⅲ of predominant micropores and macropores with poor connectivity. For coal facies, there are three various coal facies were distinguished, which include lake shore coastal wet forest swamp, the upper delta plain wet forest swamp, tidal flat wet forest swamp with Q-cluster analysis and tissue preservation index - gelification index (TPI-GI) and Wood index - groundwater influence index (WI -GWI). The results show there is positive relationship between tissue preservation index (TPI), wood index (WI) and mesopores (102nm-103nm), while a negative relationship between TPI, WI and macropores/fractures. In addition, groundwater level fluctuations can control the development of type C and D fractures, and the frequency of type C and D fractures shows an ascending trend with increasing GWI, which may be caused by the mineral hydration of the coal. Finally, from the perspective of the pore-fractures occurrence in CBM reservoirs, the wet forest swamp of upper delta plain is considered to be the optimization areas for Sanjiang-Mulinghe coal-bearing basins by a comparative study of various coal facies.

This study presents a preliminary analysis of the chemical and thermal fuel properties of Afuze (AFZ) coal extracted from coalfields in Owan East Local Government Area of Edo State, Nigeria. The chemical properties of AFZ were examined by combined scanning electron microscopy-energy dispersive X-ray (EDX), whereas the thermal properties were deduced by thermogravimetric analysis (TGA) under flash (50 °C/min heating rate) oxidative (combustion) and non-oxidative (pyrolysis) conditions. The microstructure and morphology analysis of AFZ revealed has a compact structure comprising small-to-large, irregular shaped and exfoliated grains with a vitreous appearance typically ascribed to metal elements (Ti and Fe) kaolinite, quartz, and other clay minerals. Chemical analysis revealed carbon, oxygen, aluminium, silicon, sulphur, calcium, titanium, and iron in major and minor (trace) quantities. Thermal analysis under oxidative and non-oxidative conditions revealed degradation occurs in three stages, namely; drying or demineralisation, devolatilization or maceral degradation and the formation of char/coke or ash. Lastly, the findings showed that the temperature range for the oxidative thermal degradation process (338.58 - 756.76 °C) was higher than the non-oxidative process (378.43 - 615.34 °C). This observation can be explained by the exothermic nature of the oxidative (combustion) process, which ensures greater heat supply required to thermally soften or degrade the maceral coal components. Overall, the oxidative process yielded the residual mass (RM = 21.97%) and mass loss (ML = 78.03%). The lower ML (49.03%) but higher RM (50.97%) observed during non-oxidative degradation of AFZ could be ascribed to the largely endothermic nature of the process.

Volcanic ash deposited on paved surfaces during volcanic eruptions often compromises skid resistance, which is a major component of safety. We adopt the British pendulum test method in laboratory conditions to investigate the skid resistance of road asphalt and airfield concrete surfaces covered by volcanic ash sourced from various locations in New Zealand. Controlled variations in ash characteristics include type, depth, wetness, particle size and soluble components. We use Stone Mastic Asphalt (SMA) for most road surface experiments but also test porous asphalt, line-painted road surfaces, and a roller screed concrete mix used for airfields. Due to their importance for skid resistance, SMA surface macrotexture and microtexture are analysed with semi-quantitative image analysis, microscopy and a standardised sand patch volumetric test, which enables determination of the relative effectiveness of different cleaning techniques. We find that SMA surfaces covered by thin deposits (~1 mm) of ash result in skid resistance values slightly lower than those observed on wet uncontaminated surfaces. At these depths, a higher relative soluble content for low-crystalline ash and a coarser particle size results in lower skid resistance. Skid resistance results for relatively thicker deposits (3-5 mm) of non-vesiculated basaltic ash are similar to those for thin deposits. There are similarities between road asphalt and airfield concrete, although there is little difference in skid resistance between bare airfield surfaces and airfield surfaces covered by 1 mm of ash. Based on our findings, we provide recommendations for maintaining road safety and effective cleaning techniques in volcanic ash environments.

This paper discusses the use of fly ash in concrete construction industry. Fly ash is incorporated as a supplementary cementitious material (SCM) in ordinary Portland cement (OPC) concrete in partial replacement of cement, and is recently used as a geopolymer cement in the development of geopolymer concrete (GPC) mixes. Class C and Class F fly ash high aluminosilicate content, and fine granular size contributes to concrete improved workability, lower permeability, and reduced heat of cement hydration. Due to its chemical properties, the use of fly ash in producing OPC and GPC results in increased compressive strength, higher tensile strength evaluated by measuring hardened concrete modulus of rupture (MOR), and higher modulus of elasticity (MOE). The fine size of fly ash particles increases the concrete mix packing order, and reduce the ingress of moisture, and mitigates the impact of aggressive environmental attacks through the reduction of sulfates and chlorides rate of concrete penetration. Thus, fly ash improves concrete resistivity to alkali-aggregate reactions (AAR), and reduces the corrosion of reinforcing steel, and prestressing strands. Fly ash as an economic byproduct of coal industry results in reduced material cost, increased durability, and a higher sustainability of concrete construction projects.

The main goal of this study was to evaluate sugarcane bagasse ash as a partial cement replacement material. Sugarcane bagasse ash is a by-product of fuel blending in the sugar industry. Yet all economic sugar is obtained after extraction from the cane. The disposal of the discharged waste in agriculture causes environmental problems in the sugar industry. The cement industry also creates environmental problems due to carbon dioxide emissions during cement manufacturing. Initially, bagasse ash samples were collected from the rubble of the Arjo Didessa sugar factory. The crude bagasse ash was sieved with a sieve size of 250µm. The strength of grade C-25 concrete was designed using five different concrete mixture proportions ranging from 5 to 20% cement by weight, including a water-cement ratio of 0.45. Impact strength tests were conducted at 7, 14, 21, and 28 days of age for each replacement ratio. For the experimental work, a total of 60 cubic concrete specimens were cast for compressive strength tests, and 15 cylindrical concrete specimens were cast for water absorption tests. Working compressive strength results indicated that bagasse ash could replace up to 5% of ordinary Portland cement concrete.

Capabilities of hovering unmanned aerial vehicles (UAVs) in low-altitude sensing of atmospheric turbulence with high spatial resolution are studied experimentally. The experiment was carried out at the Basic Experimental Observatory of the V.E. Zuev Institute of Atmospheric Optics SB RAS. UAV findings are compared with objective data on the state of the atmosphere that were measured by acoustic anemometers installed at weather towers at altitudes of 4, 10, and 27 m. Profiles of atmospheric turbulence were recorded with three UAVs hovering at the same heights at a distance of 5 m from the anemometers. The behavior of the longitudinal and lateral wind velocity components is studied in the frequency band 0-10 Hz before and after one-minute smoothing, which reveals long turbulent wind gusts. The discrepancy between the UAV and anemometer data is analyzed. It is found that after smoothing, the discrepancy does not exceed 0.5 m/s in 95% cases. This value meets the requirements of the World Meteorological Organization for some applications in wind velocity measurements. The spectral and correlation analysis of the UAV and anemometer measurements is carried out. The profiles of the longitudinal and lateral scales of turbulence are examined based on the UAV data and are found to be in agreement with the anemometer data to a good accuracy.

The capabilities of a quadcopter in the hover mode for low-altitude sensing of atmospheric turbulence with high spatial resolution in urban areas characterized by complex orography are investigated. The studies were carried out in different seasons (winter, spring, summer, and fall), and the quadcopter hovered in the immediate vicinity of ultrasonic weather stations. The DJI Phantom 4 Pro quadcopter and AMK-03 ultrasonic weather stations installed in different places of the studied territory were used in the experiment. The smoothing procedure was used to main regularities in the behavior of the longitudinal and lateral spectra of turbulence in the inertial and energy production ranges. The longitudinal and lateral turbulence scales were estimated by the least-square fit method with the von Karman model as a regression curve. It is shown that the turbulence spectra obtained with DJI Phantom 4 Pro and AMK-03 generally coincide with minor differences observed in the high-frequency region of the spectrum. In the inertial range, the behavior of the turbulence spectra shows that they obey the Kolmogorov-Obukhov “5/3” law. In the energy production range, the longitudinal and lateral turbulence scales and their ratio measured by DJI Phantom 4 Pro and AMK-03 agree to a good accuracy. Discrepancies in the data obtained with the quadcopter and the ultrasonic weather stations at the territory with complex orography are explained by the partial correlation of the wind velocity series at different measurement points and the influence of the inhomogeneous surface.

Based on the theory of turbulence, equations are derived for estimations of turbulent fluctuations of the longitudinal and transverse components of the wind velocity during ideal hovering of a quadcopter in a turbulent atmosphere. We present the results of experiments which were carried out on the territory of the Geophysical Observatory of Institute of Monitoring of Climatic and Ecological Systems, Siberian Branch, Russian Academy of Sciences, located in Tomsk Akademgorodok on the territory with complex orography, in a parkland zone with buildings of research institutes and motorways. Time series of turbulent fluctuations of the longitudinal and transverse components of wind velocity fluctuations were received with the use of an automated weather station, and time series of estimates of these components, from data of a DJI Phantom 4 Pro quadcopter during hovering. According to the automated weather station data, anisotropy was observed in one experiment during measurements in the atmosphere, but this phenomenon was not observed in the other experiment: the fluctuation spectra of all components of wind speed fluctuations coincide. The spectra of fluctuations of the longitudinal and transverse wind velocity components based on the automated weather station data and UAV telemetry are presented. The fluctuation spectra of these components for the automated weather station data and quadcopter generally coincide. The behavior of the spectra coincides with the spectrum which corresponds to Kolmogorov–Obukhov “–5/3” law within the inertial range. The turbulent spectra of the wind velocity fluctuations obtained with the use of the automatic weather station and with the unmanned aerial vehicle differ in the high-frequency spectral region.

Methane is a greenhouse gas and identified as a key driver of near-term climate change. Bottom-up approaches estimate annual methane loss from US natural gas production and transport at 6 Tg, but recent studies suggest this may be an underestimate. To investigate this possibility, an equipment-based emissions inventory, using EPA emission factors, was developed to calculate methane emissions from oil and gas operations in the Delaware Basin, USA. Emission factors and activity data were then updated using contemporary and region-specific measurement data. The original inventory estimated emissions at 315 Gg CH4 y-1 (gas production-normalized rate of 0.6% loss), while the updated inventory estimated emissions of 1,500 Gg CH4 y-1 (2.8% loss). The largest changes resulted from large fugitive emissions from oil production (+430 Gg CH4 y-1), updating maintenance activity emissions (+214 Gg CH4 y-1), considering flaring inefficiency (+174 Gg CH4 y-1), and the inclusion of associated gas venting (+136 Gg CH4 y-1). This study suggests that a systematic underestimate probably exists in current bottom-up inventories and identifies sources currently missing or may be incorrect. We also strongly recommend that emission factors should be validated through direct comparison against measurement campaigns that include long-tail distributions typical of oil and gas activities.

In the steeply inclined and extremely thick coal seams (SIETCS) mined using the horizontal sublevel top-coal caving (HSTCC) method, the uncertainty of gas emission is a safety threat to the mining operations. In order to reduce the occurrence of accidents, the determination of gas emission is crucial. In this paper, we first proposed a prediction model for workers at the floor coalbed to calculate gas emission on site. We then put forward a finite element numerical simulation for researchers to predict gas emission from the floor coalbed. At last, we measured gas emitted from the floor coalbed of SIETCS in Wudong Coal Mine in a specific mining period and used the data to verify the applicability and accuracy of these two gas-emission prediction methods. The results showed that the gas emission from Wudong Coal Mine was 1.08 m³/min calculated based on the prediction model and 1.07 m³/min obtained using the user-defined integration method. Both methods have their own advantages, disadvantages and applicable objects, and are important in predicting gas emission from SIETCS mined using HSTCC method.

Abstract: Unusual methane emission and spontaneous combustion of coal induced by the air leakage are both hazards during mining. The most common practice has been to improve mine safety is sealing the mining fractures. In this paper, the methane and geology, coal spontaneous combustion characteristics and the coexistence of methane emission and spontaneous combustion of coal were analyzed. The preparation system of inorganic solidified foam (ISF) in field applications is studied and the working principle of generating device consists of foam generator and mixer was expounded. The technical plan of site construction is that the foam fluids was injected to respectively seal the mining fractures behind hydraulic supports, the cavities of air return corner, and the fractures nearby the coal pillar. After the foam fluids injection, the two stress values in the coal pillar eventually maintained above 15.5Mpa and 13Mpa, respectively. It indicated that the ISF can enhance the bearing stress ability of the coal pillar by transforming the stress state from two dimensional to three dimensional. The methane concentration in the air return corner and air return roadway declined significantly to 0.63% and 0.25%. The differential pressure inside and outside of the 4301(1) goaf fluctuated between -100pa to 150pa and the concentration of CO and O2 declined to 9ppm and 6%. The CO concentration in the air return corner finally reached a stable level of 6ppm. What that all means, the foam fluids can seal the air leakage and inhibit spontaneous combustion of coal effectively.

In the end, this paper analyzed the economy from the investment in plant construction, raw material collection, product production and product sales. The resulting products include pyrolytic carbon, pyrolytic oil, pyrolysis gas. The results showed that when the treatment scale was 1 ton h−1, the pyrolysis plants with three loading modes will always be in a state of loss during the 20-year running time. When the processing scale was 9 ton h−1, the pyrolysis plant can be profitable in the first year. In the sensitivity analysis, the influence of three pyrolysis products on the total return on investment was explored. The results showed that the price change of pyrolysis oil has the greatest influence on the total return on investment (Total ROI) under the three loading methods, The price change of pyrolysis gas has minimal impact on the Total ROI. This study provides basic data and basis for the commercialization of coal-biomass co-pyrolysis technology and investment in plant construction.

This article describes the POTENTIALS project, which aimed to develop business models for the reuse of former industrial and mining sites in different regions. The project focused on the creation of eco-industrial parks as a result to enable sustainable energy production and reduce waste and pollution. A key aspect was the Territorial Impact Assessment (TIA), a new and complex policy assessment tool. Therefore, the TEQUILA (Territorial Efficiency Quality and Identity Layer Assessment) approach is used to describe the TIA and emphasizes its application in assessing the impact of EU policies and projects on territorial cohesion. It underlines the need for a differentiated understanding of the regional characteristics and potential impacts of policies; and stresses the importance of regionalized impact models for the assessment. Furthermore, the process and results of applying the TEQUILA methodology to assess the territorial impact of different scenarios of business models within the POTENTIALS project is given.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The paper proposes a game theory model of price oligopoly with a heterogeneous product, where total demand depends linearly on the minimum market price. This model develops the Bertrand oligopoly for the case of imperfect price elasticity of demand. The most interesting result is an asymmetric Nash equilibrium with different prices and sales in the situation of symmetric oligopolists. The asymmetry is explained by the fact that a decrease in the minimum market price leads not only to a reallocation of consumers among firms, but also to an increase in total demand. Modifications of a two-stage game with a leader and followers and the price discrimination model are also considered. Microeconomic substantiation of the model is given on the basis of the spatial differentiation approach.

The visual span refers to the number of letters readers can identify in a single fixation without using linguistic skills. Proponents of the visual span hypothesis postulate an influence of early visual processing on reading speed. Given the slowness of reading Arabic texts, the present work aims to study the development of the visual span and its effects on reading speed in the Arabic-speaking context. Thirty-four subjects participated in the study. The trigram task and the rapid serial visual presentation (RSVP) paradigm were used to estimate visual span size and reading speed. In line with our initial assumptions, the results showed a significant effect of grade level on reading speed (F(2,31) = 30.93, p<0.001), visual span size (F(2,31) = 20.57, p<0.001). In good alignment with previous work, our results show that visual span size could explain around 40% of the reading speed variability. Interestingly, our analyses revealed a narrowing of visual span size in our Arabic sample. The results of study 2, suggest that the poor performance in the trigram task is due to poor visual attention capacities in our Arabic readers

Criticism has been directed towards the traditional methods of management accounting employed by organizations thus far, as they fail to adequately address the growing need for competitiveness and sustainable development in a globalized environment. This criticism stems from both economic factors, such as insufficient monitoring of material, energy, and escalating overhead costs, and environmental concerns, where inadequate attention is given to vital information regarding significant environmental aspects, impacts, risks, and damages arising from the organization's activities and processes. Additionally, these methods do not sufficiently support the implementation of a functional environmental management system (EMS). Drawing upon our research in EMS standardization following the international standards ISO 1400X, as well as our knowledge gained during the development of the Slovak Technical Standard (STN) for ISO 14051, this paper presents an innovative model of environmental management accounting. This model is based on the cost accounting of material and energy flows within organizations. It serves as an enhancement framework for organizations with an existing EMS built according to the EN ISO 14001 model, as well as for organizations lacking a formalized EMS based on this standard. Within this paper, we specify, decompose, and apply the new model, focusing on the cost accounting of material-energy flows in a hypothetical organization. We meticulously examine the ten key steps of the model's structure, particularly in terms of costing and the allocation of costs to material, energy, system, and waste management.

Color can direct visual attention to specific locations through bottom-up and top-down mechanisms. Using Continuous Flash Suppression (CFS) as way to investigate the factors that gate access to consciousness, the current study investigated whether color also directly affected the timing of conscious perception. Low or high spatial frequency (SF) gratings with different orientations were shown as targets to the non-dominant eye of human participants. CFS patterns were presented at a rate of 10Hz to the dominant eye to delay conscious perception of the targets, and participants had the task to report the target’s orientation as soon as they could see it. With low-SF targets, two types of color-based effects became evident. First, when the targets and the CFS patterns had different colors, the targets entered consciousness faster than in trials where the targets and CFS patterns had the same color. Second, when participants searched for a specific target color, targets that matched these search settings entered consciousness faster compared to conditions where the target color was irrelevant and could vary from trial to trial. Thus, the current study demonstrates that color is a central feature of human perception and leads to faster conscious perception of visual stimuli through bottom-up and top-down attentional mechanisms.

Fire behavior of natural rubber latex foam under different thickness conditions(d=1,2and 5cm)were explored though a little of experiments by using the self-built small scale experimental platform. It can be shown that the flame spread law of thermally thin and thermally thickness are different. Natural rubber latex foam with thickness of 2cm show higher fire risk, which value of flame spread rate, maximum flame height, maximum mass loss rate and maximum temperature is 0.00293m/s, 851.875mm, 1.83g/s, 948K,repectively.That may because the thickness of residue formed of thermally thick materials is larger than the thin one, obstructing the contact of the natural rubber latex foam with fresh air .In addition, a special phenomenon is noticed that during the second stage, the bottom unburned zone located in the four edges(thermally thin material) and middle player(thermally thick material).

The paper deals with applying Artificial Intelligence techniques to examine CHIRP-recorded data in sand and sandstone sea-bottom sites. The provided analysis of the state of the art portrays that actual time series or spectrum backscattered data from a point on the sea bottom were rarely used as the features for machine learning models. The results of the examination indicate that types of sea bottom can be quantitatively characterized by applying logistic regression models to either the backscatter time series of a frequency-modulated signal or the spectrum of that backscatter. The examination accuracy reached 90% for the time series and 94% for the spectra. The application of spectral data as features for more advanced machine learning algorithms, and the advantages of its combination with other types of data have great potential for future research and the enhancement of remote marine soil classification.

Animal behavior analysis is a crucial tasks for the industrial farming. In an indoor farm setting, extracting Key joints of animal is essential for tracking the animal for longer period of time. In this paper, we proposed a deep network that exploit transfer learning to trained the network for the pig skeleton extraction in an end to end fashion. The backbone of the architecture is based on hourglass stacked dense-net. In order to train the network, key frames are selected from the test data using K-mean sampler. In total, 9 Keypoints are annotated that gives a brief detailed behavior analysis in the farm setting. Extensive experiments are conducted and the quantitative results show that the network has the potential of increasing the tracking performance by a substantial margin.

Bottom-up synthesis of porous NiMo alloy reduced by NiMoO₄ nanofibers was systematically investigated to fabricate non-noble metal porous electrodes for hydrogen production. The different annealing temperatures of NiMoO₄ nanofibers under hydrogen atmosphere reveal that the 950 °C annealing temperature is a key to produce bicontinuous porous NiMo alloy without oxide phases. The porous NiMo alloy as cathodes in electrical water splitting demonstrates not only almost identical catalytic activity with commercial Pt/C in 1.0 M KOH solution, but also superb stability for 12 days at an electrode potential of −200 mV (v.s. RHE).

Carbon monoxide (CO) concentrations in wildfire plumes are easily measured from satellites. This gas can be used as a proxy for carbon dioxide. Forest fires play an important role in the carbon balance and in particular the CO balance. The most likely causes of mega-fires of 2003, 2012, 2021, and 2023 in the Northern hemisphere are heat waves and severe droughts associated with changes in general circulation. Here we analyze satellite data obtained by two different sounders, AIRS and TROPOMI. Different sensitivity to the lowest troposphere allows obtaining information about anthropogenic or pyrogenic contamination of the boundary layer. Shapes of areas polluted by mega-fires in 2019-2020 (Southeastern Australia) and 2021 (Central Siberia) coincide with the areas occupied by coal deposits. The Siberian Lena and Tunguska coal basins are the two largest coal fields in the world. In 2021, their combined area accounted for 90% of fire CO emission from the entire Russian Federation. So strong fires have not observed in this area before. Under- and sub-ground coal combustion may be included into the list of wildfire fuels, at least their role for ignition should be admitted. Further research is needed to assess the importance of coal fires to global climate.

Co-integration and Causality was built to conduct studies on causality relation between carbon intensity and coal consumption leading to providing important basis for the transition to a low carbon economy. The EG two-step method was performed to study the relation between carbon intensity and coal consumption of China during 1990-2015 and the co-integration and Granger test was constructed to build up the co-integration and error correction models for analysis of the interaction between carbon intensity and coal consumption. The results showed that in long term there is a stable co-integration relation and a positive correlation between carbon intensity and coal consumption; whereas fluctuations exist in short term and there is a one-way Granger causality of carbon intensity with respect to coal consumption.

Rice husk ash (RHA) is agricultural waste with high silica content that has had proven technical feasibility as a pozzolanic material since the 1970s. Notwithstanding, its use in mortars and concrete is limited by the standards currently utilized in some countries where RHA production is high and the aforementioned pozzolanic material is not standardized. This is the case of Spain, one of the main rice producers in Europe. Nowadays, the high pressure placed on the Portland cement production sector to reduce energy use and CO2 emissions has given rise to a keen interest shown in mineral admixtures for cement manufacturing. In this research, we intend to establish the contribution of different RHA types to final blended Portland cement properties (symbol “H” was used to identify RHA in standardized cements). The experimental results demonstrated that RHA with good pozzolanic properties (large specific surface and high amorphous silica content) had to be limited to 10% cement replacement because of the severe reduction in workability at higher replacement percentages. RHA with lower reactivity, such as crystalline RHA, or fly ash (FA), can be used to prepare binary and ternary blended cements with reactive RHA. It is possible to design the following cements: CEM II/A-H and CEM II/A-(H-V) It would also be possible to design cement (CEM II/B-(H-V) with replacement values up to 30% and the same 28-day mechanical performance observed for the Portland cement without mineral addition.

Cenospheres are hollow particles in fly-ash, a by-product of coal burning, and are widely used as reinforcement for developing low density composites called syntactic foams. This study investigates the physical, chemical, and thermal properties of cenospheres obtained from 3 different sources, CS1, CS2, and CS3, for the development of syntactic foams. Description of floatation method to separate broken particles is given, and it was seen that up to 11 % of the particles were damaged. Post heat treatment samples show development of SiO2 phase in the cenosphere, which is not present in the as received product. CS3 had the highest quantity of Si element, compared to the other two, showing the difference in the source quality. The particle size distribution for CS2 is very narrow while for the others is much broader. All censopheres have porous walls but the morphology of CS2 is the most uniform and smooth. For the application of metallic layer and subsequent consolidation via spark plasma sintering, CS2 was deemed the most physically, thermally, and chemically suitable.

In large infrastructures such as dams, which have a relatively high economic value, ensuring the proper operation of the associated hydraulic facilities in different operating conditions is of utmost importance. To ensure the correct and successful operation of the dam's hydraulic equipment and prevent possible damages, including gates and downstream tunnel, to build laboratory models and perform some tests are essential (the advancement of the smart sensors based on artificial intelligence is essential). One of the causes of damage to dam bottom outlets is cavitation in downstream and between the gates, which can impact on dam facilities, and air aeration can be a solution to improve it. In the present study, six dams in different provinces in Iran has been chosen to evaluate the air entrainment in the downstream tunnel experimentally. Three artificial neural networks (ANN) based machine learning (ML) algorithms are used to model and predict the air aeration in the bottom outlet. The proposed models are trained with genetic algorithms (GA), particle swarm optimization (PSO), i.e., ANN-GA, ANN-PSO, and ANFIS-PSO. Two hydrodynamic variables, namely volume rate and opening percentage of the gate, are used as inputs into all bottom outlet models. The results showed that the most optimal model is ANFIS-PSO to predict the dependent value compared with ANN-GA and ANN-PSO. The importance of the volume rate and opening percentage of the dams' gate parameters is more effective for suitable air aeration.

Wild Chinese prickly ash with elevated antioxidants is a valuable genetic resource for Zanthoxylum bungeanum Maxim improvement. There are rich wild germplasm resources in the Qinling Mountains. In a study with wild germplasm resources from different altitudes and six cultivated varieties, the phenolic and flavonoid compounds were analyzed by high performance liquid chromatography (HPLC). The chromatograms of them were basically the same, although their chemical composition content was greatly different. The thirty samples were divided into three categories through the hierarchical clustering analysis. And catechin, hyperoside and quercitrin were considered to be key compound for the quality evaluation, by contrast, the wild samples with an altitude of 2300±50 m (Ⅳ group) had the highest content of key compounds, and showed stronger antioxidant activity and antibacterial ability, indicating that these wild samples could be used as an excellent breeding resource. This is the first time to evaluate the quality of wild Chinese prickly ash in different altitude areas of Qinling Mountains. These excellent wild germplasm resources provided substantial potential accessions for use directly in Chinese prickly ash breeding programs.

Aerated concrete, which is manufactured from binding material, sand, foaming agent and water, is currently being utilized in the construction industry because of its lightweight and durability. The binding material, cement, along with other materials used in the concrete produces huge carbon footprints during its fabrication. The utilization of natural aggregates name as coarse aggregates depletes the natural resources of the country. Therefore, huge amounts of agricultural wastes have led scholars to investigate the effectiveness of replacing conventional materials used in concrete with agricultural wastes. In the current study, rice husk ash (RHA) was used as supplementary cementing material, thereby reducing the amount of cement used in aerated concrete (AC) mixture will reduce carbon footprints. The experimental and numerical analysis were conducted to investigate structural behavior of reinforced RAC- B beams subjected to flexural load. Parametric study on structural performance of RAC- B beam under flexure were conducted using finite element analysis (FEA). From the experiment and FEA. Results from the parametric study showed that RAC-10%RHA-B with higher depth structurally performed better compared to RAC-B under flexure with greater load carrying capacity, lesser maximum deflection, and less cracks developing in the tension area.

Edward syndrome, clinically known as trisomy 18 syndrome, is an autosomal chromosomal disorder characterized by an extra copy of chromosome 18. It belongs to the category of autosomal trisomy syndromes and is the second most common, with trisomy 21 being the only more frequent occurrence. In the context of this research, we present a case study focusing on a 3-month-old female infant admitted to the emergency department due to a complex array of symptoms. The primary clinical manifestations included a persistent cough, cold, and fever lasting for eight consecutive days. Comprehensive clinical evaluations, encompassing radiological and hematological investigations, confirmed the diagnosis of bronchiolitis along with viral bronchopneumonia. Chest X-rays revealed bilateral patchy opacities and diffuse haziness, primarily concentrated in the right hemithorax. Beyond respiratory issues, the infant displayed a range of distinctive physical attributes, including low-set ears, micrognathia, cranial anomalies, flattened nasal bridge, widely spaced nipples, overlapping fingers, abdominal distention, rocker-bottom feet, and recurring limb deformities known as recurvatum. Attempts to correct the limb deformity with a hip spica cast over an extended month-long period proved unsuccessful. Chronic villus sampling (CVS) ultimately confirmed the presence of Edward Syndrome (Trisomy 18), linked to the extra chromosome 18, leading to diverse physiological and developmental abnormalities. This case underscores the critical importance of timely and precise diagnosis, highlighting the challenges involved in addressing complex medical conditions marked by multifaceted clinical phenotypes.

Although Sugarcane bagasse ash (SCBA) has good cementitious property, previous researchers have primarily aimed to improve the mechanical performance of conventional concrete or cement-based composites. Research is lacking on ultra-high performance concrete (UHPC), especially regarding tensile self-sensing properties. This paper aimed to comprehensively evaluate the SCBA effect on the UHPC’s mechanical, electrical, and tensile self-sensing properties. The results showed that SCBA below the critical incorporation concentration (CIC) improved the UHPC’s mechanical properties compared to steel fibers alone. Furthermore, adding 3.0wt% SCBA remarkably enhanced the UHPC mechanical properties where the compressive, flexural, and tensile strengths increased by 13.1%, 17.4%, and 20.6%, respectively. The SCBA content of 0.3wt% achieved the maximum UHPC electrical resistivity since values smaller or greater than this content decreased the resistivity. The SCBA-enhanced UHPC showed better tensile stress-sensing performance than UHPC without SCBA due to improved linearity and reversibility, lower hysteresis, higher sensitivity, and superior repeatability. UHPC with 0.3wt% SCBA achieved the best linearity, while UHPC with 0.9wt% SCBA showed the highest sensitivity, lowest hysteresis, and best repeatability. Overall, the content of 0.9wt% SCBA is the best in improving the overall mechanical, electrical, and tensile self-sensing performance.

It is postulated in this research that the paradox of “advances in technology and management not keeping pace with the ever-increasing urban problems” is due to the poor understanding of person-focused governance of societal, environmental and economic entities. Therefore, the objective of this paper is to present an adaptive institutional model of person-driven effectiveness and ineffectiveness. The model proposes that human, ecologic and economic outcomes are heavily influenced by a complex system of systems, spanning from individually unique “non-physical influencers” to a broader set of social and environmental influencers that have a common impact on the larger society-environment-economy (SEE) system. At the heart of the model is an analytic formulation that explains the phenomena of non-physical blocker, enhancer and indifferent that are responsible for the adaptation and maladaptation of social agents, and accordingly for the sustainability and unsustainability of SEE systems. Examples are provided to illustrate the model applications: (a) the non-physical and maladaptive syndromes as antecedents of multi-morbidity and (b) the broadened and narrowed minds as sources of sustainability and unsustainability at the SEE system level within the context of emerging technologies such as engineered nanomaterials.

The development of organic devices has been focused in their miniaturization in order to obtain denser and faster electronic circuits. The challenge is to build the devices adding atom by atom or molecule by molecule until the desired structure is achieved. To do this job, techniques able to see and manipulate matter at this scale are needed. Scanning tunneling microscopy has been the selected technique by scientists to develop smart and functional unimolecular devices. This review article compiles the latest developments in this field giving examples of supramolecular systems monitored and fabricated at molecular scale by bottom-up approaches using STM at solid/liquid interface.

This study was conducted in a laboratory-controlled environment aiming at studying the physical properties and elemental composition of coal combustion particles in a brazier. Particles were sampled ~1 m above the stove using a partector, where particles were collected on gold Transmission Electron Microscopy (TEM) grids and polycarbonate filters for TEM and inductively coupled plasma mass spectrometry (ICP-MS) analysis, respectively. Particles for elemental analysis collected on a 37 µm polycarbonate filters whereby a Gillian pump was used to draw in air. During sampling, a 2.5 µm cyclone was attached to the sampling cassette to isolate larger particles. The results have shown that combustion particles emitted during the early stage of combustion where single spherical particles with a diameter of around 450 nm. As the combustion progresses, the particle diameter gradually decreases and the morphology changes to accretion chain and fluffy bead structure for the flaming and char-burning phase, respectively.

Abstract: The present work evaluates the feasibility of using volcanic fly ash (VFA), generated by the eruption of the Tajogaite volcano on the island of La Palma (Spain) in 2021, as a precursor in the preparation of cementitious materials with different Portland cement (PC) replacement levels (0%, 30%, 70% and 100%), in the absence (Blended Cement, BC) and presence of an alkaline ac-tivator (Hybrid Alkaline Cement, HAC, and Alkaline Cements, AC). Hydration kinetics (isother-mal conduction calorimetry), paste mechanical strengths and reaction products were character-ised by XRD, FTIR, TG/DTG and BSEM/EDX. The results obtained indicate that the strengths de-veloped by the hybrid alkaline cements (HAC) are higher than those of the blended cements (BC), especially at the age of 2 days, where 25 MPa was obtained with the replacement of 70% PC by VFA. Alkaline cements (AC, 100% VFA) prepared with 8M NaOH solution as activator reached 40 MPa after 2 days. It was observed that in all the binders, depending on the initial composition of the binder mixture and the percentage of replacement and/or activator, VFA reacts to form cementitious gels, C-A-S-H and N-A-S-H type, which supports its use as a mineral addition to blended cement or as a precursor in the preparation of alkaline and hybrid alkaline cements.

It is necessary to address the scarcity of crushed stones for pavement structural layers. So fly ash can be proved to be promising solution as more than 270 tonnes of fly ash is generated in India. Though, numerous research has been conducted for the use of fly ash intreated and untreated form, high volume of fine particles and brittleness of the stabilized fly ash pose a great problem for its use in subbase and base. Moreover, stiffness or modulus of stabilized fly ash is vital elastic parameter which is used for mechanistic pavement design. Hence, in this study an extensive experimental investigation is carried out to study its strength and stiffness properties such as compressive strength, indirect tensile strength and flexural strength, cyclic indirect tensile modulus and flexural modulus of fiber reinforced cement stabilized fly ash, stone dust, aggregate mixtures. The stone dust and aggregates have been added to enhance the gradation of the composite’s mixture. The study presents the effect of fiber on strength and stiffness properties. The experimental result reveals that addition of polypropylene (PP) fibers up to 0.25 wt.% enhances the compressive strength and any further addition of fiber results in decrease of the strength. However, indirect tensile strength and flexural strength increases with increase in fiber percentage up to 0.5 wt.%. Cement content is observed to be the dominant parameter for stabilized materials. Suitable relationships have been developed between strength and modulus parameters for stabilized mixtures. Based on the strength and stiffness study, 70% fly ash and 30% stone dust-aggregate and 60% fly ash and 40% stone dust-aggregate with 6% cement can be considered for the base layer. Based on the indirect tensile strength and flexural strength behavior, 0.35% is considered as the optimum fiber percentage.

This work describes the preparation of mesoporous silica by the green reaction of rice husk ash (RHA) with glycerol, followed by the modification and the potential use as a drug carrier. The reaction was carried out at 215 °C for 2 h. The solution was further hydrolyzed with deionized water and aged for various times (24, 48, 120, 360, 528 and 672 h) before calcinations at 500 oC for 24 h. Further treatment of prepared mesoporous silica was performed using trimethylmethoxysilane (TMMS) to obtain hydrophobic Mesoporous silica. For all synthesized silica, silica contents were as high as 95%wt, whereas organic residues were less than 3%wt. RHA-glycerol showed the highest specific surface area with smallest pore diameter (205.70 m2/g, 7.46 nm) when aged for 48 h. The optimal hydrolysis-ageing period of 120 h resulted in 500.7 m2/g BET surface area, 0.655 cm3/g pore volume and 5.23 nm pore diameter. The surface modification of RHA-glycerol was succeeded through the reaction with TMMS as confirmed by FTIR. Ibuprofen was selected as a model drug for the adsorption experiments. The adsorption under supercritical CO2 was carried out at isothermal temperature of 40 ˚C and 100 bar, % ibuprofen loading of TMMS modified mesoporous silica (TMMS-g-MS) was 6 times less than mesoporous silica aged for 24 h (MS-24h) due to the hydrophobic nature of modified mesoporous silica, not surface and pore characteristics. The release kinetics of ibuprofen-loaded mesoporous silicas were also investigated in vitro. The release rate of ibuprofen-loaded MS-24h was much faster than that of ibuprofen-loaded TMMS-g-MS, but comparable to the crystalline ibuprofen. The slower release rate was attributed to the diffusion control and the stability of hydrophobic nature of modified silica. This would allow the design for the controlled release drug delivery system.

With the continuous development of deep learning, the application of object detection based on deep neural network in the coal mine has been expanding. Simultaneously, as the production applications demand higher recognition accuracy, most research chooses to enlarge the depth and parameters of the network to improve accuracy. However, due to the limited computing resources in the coal mining face, it is challenging to meet the computation demands of a large number of hardware resources. Therefore, this paper proposes a lightweight object detection algorithm designed specifically for coal mining face, referred to as CM-YOLOv8. The algorithm introduces adaptive predefined anchor boxes tailored to the coal mining face dataset to enhance the detection performance of various targets. Simultaneously, a pruning method based on the L1 norm is designed, significantly compressing the model's computation and parameter volume without compromising accuracy. The proposed algorithm is validated on the coal mining dataset DsLMF+, achieving a compression rate of 40% on the model volume with less than a 1% drop in accuracy. Comparative analysis with other existing algorithms demonstrates its efficiency and practicality in coal mining scenarios. The experiments confirm that CM-YOLOv8 significantly reduces the model's computational requirements and volume while maintaining high accuracy.

This paper aims to investigate the coal thickness change area of the combined rock strata energy accumulation law. The method of connecting a uniaxial compression experiment with a theoret-ical analysis is used in this work. We employ a combination of coal and rock to carry out our studies. We investigate how different lithologies and ratios of coal-rock height affect the me-chanical properties of the mixture and the law governing energy accumulation. We have deter-mined the following facts: (1) The combination's peak strength and elastic modulus exceed that of coal and are inferior to that of rock but are nearer to that of coal. (2) When the coal-rock height ratios are dissimilar, the peak strength and modulus of elasticity of the combination show a negative correlation with the coal-thickness share, and the pre-peak energy accumulation and impact energy index of the combination shows a positive correlation with the coal-thickness share. (3) For the combination with the same coal-rock height ratio, the peak strength, elastic modulus, pre-peak energy accumulation, and impact energy index all increase with greater rock strength and elastic modulus. The presence of a hard rock layer affects the accumulation of pre-peak energy. ( 4 ) The stress in the surrounding rock gradually decreases as the coal thick-ness increases. In the area where coal thickness declines, the stress in surrounding rock is higher than that in the region where it thickens. The energy stored in the surrounding rock is directly proportional to the coal in the zone. Conversely, areas with thinner coal deposits exhibit a lower energy storage capacity in the surrounding rock than those with thicker coal deposits. The stress distribution of surrounding rock in coal thickness change is abnormal; substantial energy accu-mulation can swiftly initiate dynamic disasters, such as rock bursts. This study has important reference significance for preventing and controlling rock burst in coal thickness change areas.

As on 31.03.2020, 55.4 % (205135 MW) of total installed capacity (370106 MW) in India is through coal and lignite based power plants. These plants, set up by central, state and private utilities with substantial capital investment are facing consistently reducing Plant Utilization Factor (known as Plant Load Factor, PLF, in India). In the year 2019-20 the national average thermal power PLF stood at 55.4%, down from 78.6 % in 2007-08. On the other hand, the electricity demand is consistently rising in the country and there exists a peak and energy shortage at national level. In 2019-20 energy shortage was 0.7 % and peak shortage was 0.5 %. A disturbing paradox therefore exists here. On one hand, the country is power deficit, and on the other hand, a large amount of coal based affordable power, ready to be generated by thermal power generators, remains grossly unused. Looking into the fact that considerable investment has gone into developing these thermal power generation assets in the country, the falling PLF is a matter of concern for all the key stakeholders including the power producers, lenders, regulators and consumers. This paper identifies seven major factors that are affecting PLF of thermal power plants and then makes an attempt to project future scenario of PLF so that critical stakeholders can intervene through appropriate actions. Primary research with responses from power professionals has been used to find out the major factors. Future projection of PLF has been done using Partial Least Square (PLS) regression. Projection shows that in the Business As Usual case (Factors increasing at the current CAGR rate), the thermal power plants will face very low level of PLF (14.76 %) by 2024-25. This will mean that many plants will be shut down and many will run for only few hours in a day that too at very low loads. If the future generation mix is kept as indicated by Central Electricity Authority (CEA), a Govt. of India in its report (Draft report on optimal generation capacity mix for 2029-30- CEA- Govt of India) then the thermal power plant average PLF can sustain above 68 % until 2024-25. If followed, this path can be a breather for the thermal power plants.

Fly ash cement has rarely been used in Japan, mainly because its strength development is slower than ordinary Portland cement. In this research, the effect of the new fly ash cement with both high alite (C3S) cement and fly ash modified by electrostatic belt separation method on cracking resistance of precast concrete prepared by steam curing was studied. The mechanical and shrinkage properties of the proposed fly ash concrete were compared with those of concrete made using OPC cement without fly ash. In order to study the cracking tendency of precast concrete with the proposed fly ash cement, thermal stress analysis was conducted taking into consideration of the experimental data of concrete properties with the different concrete mix proportions. A standard precast concrete box culvert model was used in this 3D FEM analysis and the distribution of temperature and relative humidity in cross section and induced restraint stress during and after steam curing were discussed. Steam-cured concrete with fly ash and high alite cement developed higher compressive strength on the first day of age than concrete with OPC. The proposed fly ash concrete developed high cracking resistance in the early days. On the other hand, the results showed that the drying shrinkage at later ages was the main cause of cracking.

An attempt to investigate the effect of binary composite activators on the microstructure of fly ash-based geopolymers is conducted through the comparison of 24 experiments, which consisted of Na2SiO3•9H2O, Na2CO3, K2CO3, NaOH, and KOH through a facile preparation technique. The results show that the activator of Na2SiO3•9H2O+KOH presents the highest mechanical strength, due to the synergy activation between the inherent ≡Si-O-Si≡ chains derived from Na2SiO3 and K+’s catalysis. It reveals that the K+ plays a crucial role in Na2SiO3-activated fly ash geopolymer, which is the rate-determining step of the enhanced crosslinking and propagation of N-(C)-A-S-H chains, leading to an increase in weight loss temperatures of specimens from TG/DTG results. Furthermore, the adding silica fume facilitates as-formed amorphous silicates, which also could fill into the pores of N-(C)-A-S-H amorphous gels and present a uniform and compact morphology, leading to an increase in the pore volume of the pore diameter less than 100 nm. It explores an efficient and cost-effective preparation of fly ash-based geopolymer for developing solid-waste recycling techniques.

This article deals with the possibility of partial replacement of blast furnace slag with fly ash after denitrification by the Selective Non-Catalytic Reduction (SNCR) method in alkali-activated materials. In the experiment, the basic physical-mechanical properties and durability properties were tested, the hydration reaction was monitored in a calorimeter and infrared spectroscopy was performed. Results were compared between mixtures prepared with fly ash without denitrification and also with reference mixture based only on alkali-activated blast furnace slag. The basic result is the finding, that hybrid alkali-systems with fly ash after denitrification show similar trends as hybrid alkali-systems with fly ash without denitrification. The significant effect of fly ash is manifested especially in terms of resistance to freeze-thaw. The reactions in the calorimeter show a slower development of reactions with increasing replacement of slag by fly ash. In the case of testing resistance to leaching in demineralised water, a decrease of flexural strength was found, which corresponds to the conclusions of strength testing, that long-term deposition of bodies in water causes deterioration of mechanical properties.

New materials are obtained by transforming fly ash wastes into a valuable composite, with tandem adsorption and photodegradation properties. Mild hydrothermal synthesis, from titanium dioxide, Platinum nanoparticles and zeolite materials obtained from a waste, fly ash, as support, was involved in the composite preparation. The Platinum nanoparticles extended the photocatalytic activity of the composite in Visible range (Eg = 2.1 eV). The efficiency of tandem adsorption and photocatalytic activity of the new composite were evaluated to 80.70% for Bemacid Blau and 93.89% for Bemacid Rot, after 360 min, the irradiation time, with H2O2 addition.

Agrilus planipennis is a devastating invasive pest of ash trees. This wood-boring insect native to Asia and established in European Russia about 20 years ago poses a serious threat to ash trees all over Europe. In 2019 we first detected Agrilus planipennis in Ukraine. More than 20 larvae have been collected from under the bark of Fraxinus pennsylvanica trees on 5 September 2019 in Markivka District of Luhansk Region. Coordinates of the localities of collection: 49.614991 N, 39.559743 E; 49.614160 N, 39.572402 E and 49.597043 N, 39.561811 E. The photos of damaged trees with larval galleries, exit holes and larvae are presented. There is no doubt that the pest is established in Ukraine. This fact is important for development of quarantine protocols to prevent or at least slow the further spread of this invasive pest in Europe.

This paper presents an acoustic emission (AE) detection method for refined oil storage tanks, enabling online detection of corrosion points and microleakage in the tank floor. The method utilizes an explosion-proof acoustic emission instrument to detect the floor of a refined oil storage tank. By calculating the time difference between the defective acoustic signal and the speed of acoustic wave transmission, a mathematical model is constructed to analyze the detected signals. A technical scheme for acoustic emission detection in storage tanks is designed, and the instru-ment is used to carry out acoustic emission testing on the product oil storage tank floor. Based on these test results, location analysis of acoustic emission sources is conducted on the bottom plate of the tank, evaluating its corrosion condition accurately. The consistency between the evaluation and subsequent open tank tests confirms that using acoustic emission technology effectively captures corrosion signals from product oil storage tank bottoms. Consequently, it significantly improves inspection efficiency by avoiding unnecessary tank-opening operations. Combining this method with open tank inspection operations such as the leakage magnetic method, one can fully grasp the status of the refined oil storage tanks.

The damage evolution rules of coal under true triaxial combined static-dynamic loads are important to understand and reveal the mechanism of rockburst in coal mines. The numerical simulation was carried out using FLAC3D to explore the coupling effect of static and dynamic stress, especially the influence of dynamic load parameters. The results show that the increase of dynamic load amplitude not only makes the plastic zone grow exponentially and shorten the damage development time, but also decreases the residual strength of the coal sample, which leads to a much more violent of the dynamic failure. The stress wave can propagate more stable in the coal sample with the increase of dynamic load frequency and the development time of the plastic zone also show synchronous fluctuating features, and when the frequency is like the intrinsic frequency of the coal sample, the dynamic load has a significant stimulate effect. The static and dynamic loads have different damage effect to the coal sample under true triaxial stress path, the weight decreases in order of the minimum principal stress, the maximum principal, the amplitude of the dynamic load and at last the dynamic stress frequency by the entropy weight method analysis.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

DFT-D3 calculations based on structural X-ray diffraction data obtained for 3-oxo-camphorsulfonyl imine (1), camphorsulfonyl chloride (2) and seven camphor sulfonimines (O2SNC10H13NR, L1-L7) from which L2 (R=4-OHC6H4), L4 (R=4-ClC6H4) and L6 (R=3,5-(CH3)2C6H3) are new, provide information into the intra and inter molecular interactions with concomitant elucidation of the supramolecular arrangement of the compounds. The DFT D3 calculations performed in small clusters of 2 or 3 molecular units reproduce the interactions observed by X-ray analyses showing that as a general trend the structural arrangement of the molecules is driven by electronic rather than by packing parameters. In all compounds the self-assembly of 3D structures involves the sulfonyl imine group ( NSO2) either to establish hydrogen bonds, through the oxygen atoms or non-classic oxygen-aliphatic hydrogen or non-bonding interactions (NBI) which also involve the sulfonyl oxygens. Interestingly, the camphor sulfonimine compounds (L2, L3) having protic groups (R=C6H4X: X=OH, L2 or X=NH2, L3) at the aromatic imine substituents (=NR) present an extra π-π stacking which is absent in the other compounds aromatic derivatives. The X-ray analysis shows that all the reported camphor sulfonimine compounds display the E configuration with respect to the imine substituent (R). The study of the redox behavior of the compounds by cyclic voltammetry allows an insight into the solution properties of the compounds and the rationalization of the molecular interactions that stand in the solid and solution states. Camphor sulfonimine compounds (L) display appropriate binding atoms to coordinate transition metals. The herein results show that monodentate coordination through the nitrogen atom of the sulfonimine 5-membered ring to the {Ag(NO3)} metal center is favored. When this imine nitrogen atom is not itself involved in the Organic Framework DFT-D3 calculations shows that the complexation does not affect the non-covalent interactions that are reproduced in the MOF structure.

Paleopeat-forming environments have an important effect on the dispersion and enrichment of trace elements in coal. The C3 coal seam of the Xuanwei Formation in eastern Yunnan was used as a case study to reconstruct the paleopeat-forming environment based on the coal facies parameters and geochemical characteristics, and its influence on trace element (including rare earth elements and yttrium, REY) enrichment was investigated. The C3 coal was classified as medium rank coking coal with an ultra-low moisture content, medium-high-ash yield, and low-medium volatile content. Compared to the average values for Chinese coals, Cu and V were enriched and Co was slightly enriched in the C3 coal. Compared with the average values for world coals, Cu and V were enriched, while several other trace elements were slightly enriched, including Co, Hf, Nb, Sc, Ta, Zn, and Zr in the C3 coal. The C3 coal was deposited in a low peat mainly limno-telmatic swamp, with deep water, weak hydrodynamic conditions, brackish to salty water, and reducing conditions. Trace elements, including Cu, V, Hf, Nb, Sc, Ta, Zr, and REY, are typically enriched in a limno-telmatic environment with fresh water, and reducing and weak hydrodynamic conditions. Additionally, REY and V are also significantly enriched in brackish water limno-telmatic conditions with the same depositional environment.

: Kentucky is one of the largest coal producing states and surface coal mining has led to changes in natural land cover, soil loss, and water quality. This study explored relationships between actively mined and reclaimed areas and vegetation change and water quality parameters. The study site evaluated 58 watersheds with Landsat-derived variables (reclamation age, mining percentage, reclaimed forest percentage, and reclaimed woods percentage) as well as topographic variables (such as elevation, slope, drainage density, and infiltration). Water samples were collected in spring (n=9), summer (n=14), and fall (n=58) 2017 to study changes in water quality variables (SO42-, alkalinity, conductivity, Ca2+, Mg2+, Mn2+, Al3+, and Fe2+,Fe3+) in response to changes in land cover. Pearson correlation analyses indicated conductivity has strong to very strong relationships with other variables of water quality variables related to coal mining (except Al3+, Fe2+,Fe3+, Mn2+, elevation, slope, and drainage density) and land cover variables. In addition, separate multivariate regression analyses were performed with conductivity values based on samples collected in the fall. First, conductivity response to mining percentage, reclamation age and topographic variables were examined (adjusted R2=0.818, p &lt; 0.01). Next, vegetation cover change parameters were added to the same model, which yielded slightly improved R2 (adjusted R2 = 0.826, p &lt; 0.01). Finally, reclamation age and mining percentage were used to explain the quantity of reclaimed forested areas as a percentage of watersheds. The model was significant (p &lt; 0.01) with an adjusted R2 value of 0.641. Results suggest that the quantity (area as a percentage) of reclaimed forests may be a predictor of mining percentage and reclamation age. This study indicated that conductivity is a predictable water quality indicator that is highly associated with Coal Mine Related Stream Chemistry in areas where agriculture and urban development are limited. These findings may help the scientific community and key state and federal agencies improve their understanding of water quality attributes in watersheds affected by coal mining as well as refining land reclamation practices.

The recognition of coal-rock interface is very crucial for the research in the intelligent production of coal mine. This study investigates the application of terahertz time-domain spectroscopy in the recognition of coal-rock interface, including the identification of coal-rock and coal-rock mixtures, as well as the accurate characterization of coal seam thickness. Terahertz detection was used to obtain the optical parameter information of the pressed pellets prepared by mixing two different kinds of coal and two kinds of rock. Based on the experiment results, the database was established for the identification of coal-rock interfaces in coal mining machines. The terahertz detection was performed on 10 different kinds of sheet anthracite with different thickness, and the terahertz spectra of coal seams with different thickness were simulated and calculated by using simulation software, which can accurately obtain the thickness of coal seams and provide effective mining thickness parameters for coal seam mining. Through the experiment and simulation, the terahertz time-domain spectroscopy technology has a promising application prospect in the identification of coal-rock interface.

Swirling coal flames are encountered in swirl burners of boiler furnaces and cyclone coal combustors, and were studied using large-eddy simulation (LES) in reported references. However, the structures of swirling coal flames remain to be further studied. In the present paper LES of swirling coal flames is conducted for two combustors using two gas combustion models. The statistical simulation results are accessed by experiments and the instantaneous simulation results are used to analyze the specific features of flame structures of four cases. It is seen that different inlet flow conditions and different secondary-air flow rate lead to different flame structures

Coal is an important resource that is closely related to people’s lives and has an irreplaceable role. However, coal mine safety accidents occur from time to time in the process of working underground. To this end, this paper proposes a coal mine environmental safety early warning model to detect abnormalities and ensure worker safety in a timely manner by assessing the underground climate environment. In this paper, the support vector machine (SVM) parameters are optimized using an improved artificial hummingbird algorithm (IAHA), and its safety level is classified by combining various environmental parameters. To address the problems of insufficient global exploration capability and slow convergence of the artificial hummingbird algorithm during iterations, a strategy incorporating Tent chaos mapping and backward learning is used to initialize the population, a Levy flight strategy is introduced to improve the search capability during the guided foraging phase, and then the simplex method is introduced to replace the worst value before the end of each iteration of the algorithm. The IAHA-SVM safety warning model was established using the improved algorithm to classify and predict the safety of the coal mine environment into four classes. Finally, the performance of the IAHA algorithm and the IAHA-SVM model are simulated separately. The simulation results show that the convergence speed and the search accuracy of the IAHA algorithm are improved, and the performance of the IAHA-SVM model has a significant improvement.

To improve water injection effect, microemulsions (MEs) were used to wet coal seam compared with water and sodium dodecyl sulfate solution (SDS). Wetting effects were characterized by contact angle, X-ray diffraction, Fourier infrared spectroscopy. The results showed that the microemulsion has better spreadability on coal surface and has stronger wettability for coals of different ranks and different particle sizes than traditional wetting agents. The W/O type microemulsion is more affinity to coal than the O/W type and the bicontinuous type.Oxygen and hydrogen contents contributed to wetting. Different wetting agents have the greatest impact on the oxygen-containing functional group absorption zone of coal, but have little impact on the change of clay mineral composition.As the content of quartz increased, the content of montmorillonite was decreased, and the hydrophilicity of coal was increased. This research proposes new ideas for solving coal dust problems and reducing coal mine disasters.

Existing methods for detecting magnetic leakage signals from damaged wire ropes require axial saturation magnetisation, and the accuracy of the detection equipment depends on the saturation degree of magnetisation. Moreover, the expected magnetisation effect is usually difficult to achieve owing to the special characteristics of the rope structure, diameter, and operating environment of the wire rope. Consequently, in addition to other issues, the detection accuracy and versatility of the equipment are low. In this study, a method based on spatial multidimensional orthogonal array loop magnetisation for detecting mine wire rope defects is proposed. Firstly, a new sensor excitation structure model is developed. Then a method of radiant magnetic flux of permanent magnet array is analysed, and the influence law of the number of permanent radiant magnetic blocks on the magnetisation effect is studied. In addition, a method of wire rope detection based on the principle of clustering is investigated, according to which the influence law of the shape, structure, and size of the polyurethane device on the effect of magnetisation is discussed. Finally, through laboratory experiments, the test model and proposed method are verified. The results show that the magnetisation effect is better and more cost-effective when the number of permanent magnet radiation magnetic block is n=8, and the proposed detection method can effectively distinguish damaged wire rope joints. Furthermore, the proposed equipment achieved signal-to-noise ratio of the signals, improving the reliability of damage detection.

Residential coal combustion is one of the most significant sources of carbonaceous aerosols in the Highveld region of South Africa, significantly affecting the local and regional climate. In this study, we investigated single coal-burning particles emitted when using different fire-ignition techniques (top-lit up-draft vs bottom-lit up-draft) and air ventilation rates (defined by the number of air holes above and below the fire grate) in selected informal braziers. Aerosol samples were collected on nucleopore filters at the Sustainable Energy Technology and Research Centre Laboratory, University of Johannesburg. Individual particles (~700) were investigated using a scanning electron microscope equipped with energy-dispersive X-ray spectroscopy (EDS). Two distinct forms of spherical organic particles (SOPs) were identified, one less oxidized than the other. The particles were further classified into "electronically" dark and bright. EDS analysis showed that 70% of the dark spherical organic particles had higher (~60%) relative oxygen content than in the bright SOPs. We quantified the morphology of spherical organic particles and classified them into four categories: ~50% are bare single particles; ~35% particles are aggregated and form diffusion accretion chains; 10% have inclusions, and 5% are deformed due to impaction on filter material during sampling. We conclude that there are two distinct kinds of coal burning spherical organic particles and that dark SOPs are less volatile than bright SOPs. We also show that these spherical organic particles are similar in nature and characteristics to tar balls observed in biomass combustion and that they have the potential to absorb sunlight thereby affecting the earth’s radiative budget and climate. This study provides insights into the mixing states, morphology, and possible formation mechanisms of these organic particles from residential coal combustion in informal stoves.

This article addresses the urbanization model in valley bottom areas in the city of São Paulo, an-alyzed in its urban planning and socio-environmental aspects, and examines the hydrological impacts triggered by its implementation. It argues that sustainable occupation of urbanized hy-drographic basins should be based on environmental criteria in order to attain a sustainable water management regime that can ensure urban and environmental resilience. In the “Introduction,” the article emphasizes that urbanization in São Paulo has neglected the natural features of river basins, promoting the channeling of watercourses, which resulted in floods and inundations. “Theoretical Basics” brings in key concepts related to the environmental approach of drainage infrastructure with gray and green-blue systems. “Methods” details our qualitative research, bibliographical analyzes, referential case studies, and cartographical analyzes (geoprocessing), focusing on a case study in the Jaguaré creek basin. “Results” includes guidelines and recom-mendations for an urbanization model adjusted to valley bottom areas, applicable to new patterns of urban occupation or to the adjustment of existing patterns. “Discussion” explores the concept of “local sustainable self-development,” and “Conclusions” highlights the importance of an inte-grated, multisectoral, and sustainable planning, adjusted to the characteristics of river basins in valley bottom areas, promoting a socially responsible urban occupation, especially in the face of climate change.

Protein translational modifications (PTMs) generate an enormous, but as yet undetermined, expansion of the expressed proteoforms. In this Viewpoint, we firstly differentiate the concepts of proteoform and peptidoform by reviewing and discussing previous literature. We show that the current PTM biological investigation and annotation largely follow a PTM site-specific rather than proteoform-specific approach. We further illustrate a potentially useful matching strategy in which a particular “modified peptidoform” is matched to the corresponding “unmodified peptidoform” as a reference for the quantitative analysis between samples and conditions. We suggest this strategy could provide directly relevant information for learning the PTM site-specific biological functions. Accordingly, we advocate for the wider use of the nomenclature “peptidoform” in the future bottom-up proteomic studies.

In this study, changes in the microstructure of coal tar pitch during successive processes, including pyrolysis, polycondensation, and crystallization, were examined in connection with the resulting variations in structure factors, as measured by XRD analysis, and functional groups, as confirmed by FTIR spectroscopy. To this end, four zones were defined based on variations in crystallinity, which were indicated by d002 and Lc. Each zone was further characterized by interpreting crystallinity development in relation to changes in functional groups and specimen height. At around 400 °C, polycondensation occurred as the C-Har and C-Hal peaks decreased in intensity. These peak reductions coincided with the formation of mesophase spheres, resulting in enhanced crystallinity. Subsequently, at around 500 °C, the peak intensity of C-H and COOH decreased, which was attributed to the release of large amounts of gasses. This led to sharp volume changes and a temporary reduction in crystallinity. All these results suggest that changes in the functional groups of coal tar pitch at lower temperatures (600 °C or less) during the carbonization process are closely associated with variations in its crystallinity. The major findings of the present study provide valuable insights for designing highly effective processes in the manufacturing of synthetic graphite blocks using CTP as a binder material, including by selecting appropriate temperature ranges to minimize volume expansion and crystallinity degradation and determining the lowest possible carbonization temperature to ensure adequate binder strength.

The safe and efficient mining of coal seams with low porosity, low permeability and high inhomogeneity under complex geological conditions is a major challenge, among which the permeability of coal seams is crucial for coal mine gas extraction. The development of coal seam permeability enhancement technology can help coal mines to produce safely and efficiently, and the extracted coal bed methane can be utilized as a green energy. In order to study the effect of freezing and thawing on the evolution of mechanical and permeability properties of coal, triaxial permeability tests were carried out on low-permeability coal under two kinds of surrounding pressures. At the same time, dry, saturated and freeze-thaw coal were set up for comparison, and the effects of water and freeze-thaw were separated from each other. The triaxial mechanics and percolation laws of dry, saturated and freeze-thaw coal rocks were obtained, and the mechanism of the influence of freeze-thaw on the permeability evolution law of coal was revealed. The research results can provide theoretical guidance for the gas extraction technology of low permeability coal seams with increased permeability.