Based on the previous work done by Fujii et al., NdBaInO4 compounds present modest oxide-ion conductivities. Therefore, it has been an attractive system of significant interest. In this paper, the Ca element has been attempted to partially substitute for Nd and the total electrical conductivity has been successfully improved due to the generation of oxygen vacancies. The synthesis, crystal structure, density, surface topography and electrical properties of NdBaInO4 and Ca-doped NdBaInO4 have been studied respectively. NdBaInO4, 10% and 20% molar fraction of Ca doped NdBaInO4 were synthesized through solid state reaction and they were calcined at 1000 °C for 14 hours and sintered at 1440 °C,1430 °C and 1420 °C respectively. The crystal structure of them has been obtained from Le Bail refinement of the XRD pattern, giving the result of the monoclinic structure which belongs to P21/c space group. The size of particles processed with different ball milling time and surface topography have been detected by the scanning electron microscope. The total electrical conductivities of Nd1-xCaxBaInO4-x/2 (x = 0, 0.1 and 0.2) were measured in the dry atmosphere by AC impedance spectroscopy and Nd0.9Ca0.1BaInO3.95 exhibited the highest total electrical conductivity and the lowest activation energy. What is more, the total conductivity of Nd0.9Ca0.1BaInO3.95 in the wet atmosphere at moderate temperature is relatively higher than that in the dry atmosphere while this phenomenon was not found in NdBaInO4. Therefore, the excess conductivity suggests that potential proton conduction may exist in wet atmospheres. In addition, Ca-doped NdBaInO4 were chosen for the oxygen isotope exchange which aims to obtain the diffusion coefficient and surface exchange coefficient, and Nd0.9Ca0.1BaInO3.95 shows the highest diffusion coefficient and D* decreases with the increase of the molar fraction of the Ca element.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

The aim of this work is evaluation of corrosion behavior of SS 304 coated through TIG process. In this work, Ti tube cored with graphite powder was applied. Experimental processes were shown that the optimum parameters for coating procedure are voltage of 15V, current density of 120A and the speed of 2.1mm/s. Investigations on corrosion resistance of coating are shown that not only this composite coating can improve the tribological behavior of this type of stainless steel, but also there is an improvement in its deteriorative property. Moreover, it is observed that mass reduction in coating is 5 times lower than the base metal.

The aim of this paper is to develop a composite coating on St 304 steel employing TIG process. Ti wire cored with graphite powder is used as the means of coating material. The process parameters are varied in order to develop coating with optimum characteristics (i.e., hardness and wear resistance). The microstructure of the coating is analyzed with SEM and XRD. It is found that both of the hardness and wear resistance increase as the current increases while both of these properties decrease as the travelling speed increases. It is found that the coated samples with composite layers have more hardness than the substrate and it could range up to 1100 HV being almost 4.5 times higher than the hardness of St 304. Likewise, the wear resistance of coating is observed to be 4.5 times higher than that of substrate. The high performance of coating, as revealed by microstructural analysis, is due to formation of TiC and Cr₂₃C₆ .The optimum conditions to produce the coating are proposed to be 120 A current and 3.17 mm/s travel speed.

Tungsten carbide (WC) was well known as a wear-resistant material. Iron-based pow-der was suitable for remanufacturing of cast iron engine parts. To improve the wear resistance of the remanufactured iron-based cast iron engine parts, WC-Co was intro-duced into iron-based powders to prepare composite coatings for cast iron engine components. In this work, FeAlC-x(WC-Co) composite coatings were prepared by plasma transfer arc on compacted graphite cast iron. The influences of WC-Co con-tents in the Fe-AlC-x(WC-Co) composite coatings on the microstructure and properties of the composite coatings were investigated. The composite coatings contained γ-Fe, α-Fe, WC and Fe3W3C mainly. The microhardness of FeAlC-x(WC-Co) composite coatings had the highest hardness of 814 HV0.2, the-lowest coefficient of 0.5 and the lest wear mass loss of 1.3mg when the weight content of WC-Co in the composite coating was 20wt%. As compared with the FeAlC coating, FeAlC-x(WC-Co) composite coating achieved the effect of reducing friction and wear resistance simultaneously, which resulted from the self-lubricating effect of graphite and high wear-resistance of carbides in the claddings.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

In the present study, an epoxy-modified silica nano-composite coating was deposited on an aluminum substrate and ACSR conductor. For this purpose, super-hydrophobic modified silica nanoparticles based on the TEOS and MTES precursors were prepared. Then, the modified silica nanoparticles were added to the epoxy resin solution. The coating deposition on an aluminum substrate and ACSR conductors was performed by a spraying method. The structure, morphology, and chemical analysis of the nanoparticle’s surface were studied with X-ray diffractometer (XRD), Transmission electron microscopy (TEM), and Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) methods. The water contact angles on the prepared samples were measured by a water contact angle analyzer method. Icing tests were performed at a constant operating temperature of -14 °C. Also, the self-cleaning behavior of the samples was evaluated with an iron oxide powder. The results indicated that the epoxy-modified silica nano-composite coating showed hydrophobic (CA, 141°), anti-icing, and self-cleaning properties.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Q345 steel is widely used in the construction industry, vehicle manufacturing industry, bridge construction industry and many other aspects due to its excellent comprehensive performance. However, due to its high silicon content, direct hot-dip galvanizing will lead to a series of problems, such as easy peeling of the coating due to the "silicon reactivity". In this paper, we adopt the "two-step hot-dipping method", first hot-dip aluminizing and then hot-dip galvanizing, to isolate the substrate and zinc liquid direct contact, so as to avoid the occurrence of "silicon reactivity". Through the microstructure characterization, neutral salt spray corrosion experiments, electrochemical experiments, the results show that: Al-Zn composite coatings from the inside out were perpendicular to the substrate growth of loose Fe2Al5 layer and Al-Zn layer, outbursts generation; Al-Zn composite coatings resistance to neutral salt spray corrosion was far more than the substrate; Al-Zn composite coatings polarization curve corrosion potential than the substrate was lower than that of the substrate by 0.512V, showing a strong corrosion resistance. It shows extremely strong corrosion resistance.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

Exploring for green and affordable protection of perishable fruit like cherry tomato is of significance. Here the protective efficacy and its underpinnings of coating with oleaster gum, alone or incorporated with cuminal, on cherry tomatoes stored at ambient temperature were investigated. The composite coating of oleaster gum with 0.1% cuminal reduced decay, respiration rate, weight loss, and softening of the fruit and decelerated their decreases of total soluble solids, titratable acidity, and soluble proteins, and therefore maintained their marketability. Furthermore, it reduced the accumulation of O•− 2and H2O2 in fruit, and mitigated cell membrane lipid oxidation and permeabilization, thereby retarding their senescence. Instrumentally, it elevated the activities of superoxide dismutase, catalase, peroxidase, and ascorbate peroxidase and the levels of ascorbic acid and glutathione. This potentiation of the fruit antioxidant system makes the composite coating a promising approach to keeping the postharvest quality of perishable fruit.

High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

To mitigate lithium dissolution and polysulfide shuttle effect phenomena in high energy lithium sulfur batteries (LISBs), a conductive, flexible, and easily modified polymer composite layer was applied on the anode. The polymer composite layer includes polyaniline and functionalized graphite. The electrochemical behavior of LISBs was studied by galvanostatic charge/discharge tests from 1.7 to 2.8 V up to 90 cycles and via COMSOL Multiphysics simulation software. No apparent overcharge occurred during the charge state, which suggests that the shuttle effect of polysulfides was effectively prevented. The COMSOL Multiphysics simulation provides a venue for optimal prediction of the ideal concentration and properties of the polymer composite layer to be used in the LISBs. The testing and simulation results determined that the polymer composite layer diminished the amount of lithium polysulfide species and decreased the amount of dissolved lithium ions in the LISBs. In addition, the charge/discharge rate of up to 2.0 C with a cycle life of 90 cycles was achieved. The knowledge acquired in this study was important not only for the design of efficient new electrode materials, but also for understanding the effect of the polymer composite layer on the electrochemical cycle stability.

In this work, electrochemical deposition (galvanostatic and potentiostatic) techniques were used to obtain of new composite polymer: 3-methylpyrrole - sodium dodecyl sulfate/poly 2-methythiophene (P3MPY-SDS/P2MT) coatings on cobalt -based alloy sample for anticorrosion protection. The sodium dodecyl sulfate as a dopant ion used in electropolymerization practice can have a relevant effect at the anticorrosion protection of the composite polymer layer by blocking the entry of aggressive ions. The cobalt -based alloy substrate had an important influence on the electrochemical performance of the composite coating and this together with the presence of the polymeric layer was achieved by simultaneously formation of a complex oxides film and polymeric layers. The polymeric coatings were analyzed by cyclic voltammetry, Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) methods. The corrosion protection of P3MPY-SDS/P2MT coated cobalt based alloy has been explored by potentiostatic and potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) procedures in1 M HCl medium. The corrosion establishment of P3MPY-SDS/P2MT covered cobalt based alloy was observed to be ~10 times less than that uncoated specimen and the effectiveness of these composite layers of this coating is above than 90%. The superior efficacy is achieved by the electrochemical polymerization of P3MPY-SDS/P2MT obtained at 0.5 mA/cm2 and 1mA/cm2 current densities and at 0.9V and 1.0V potential applied and in molar ratio 5:1. Corrosion tests result indicated that P3MPY-SDS/P2MT coatings provide good corrosion protection of cobalt -based alloy in aggressive environments.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

This paper presents a new method of preparing a coating on the Ti65 titanium alloy by a two-step procedure comprising hot-dipped aluminum and solid carburization. The effects of the carburization in the presence of NaCl deposit at 810oC have been systematically studied. In this article, the microstructure, morphology, phase composition of the coating, and the corrosion products were investigated by SEM, EDS, and X-ray diffraction. Results indicated that the corrosion resistance of hot dip aluminum/carburizing composite coating was not significantly enhanced by hot dip aluminum coating. This can be attributed to the formation of TiC and Ti3AlC after carburization, which promoted the formation of loose and unprotected TiO2 in the coating during molten salt corrosion. In addition, the oxidation of the carbon atom into CO2 /CO leaded to a high concentration of vacancy in the coating, creating channels for NaCl to penetrate the coating and accelerated the corrosion rate.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Both grape pomace and whey are waste products from the food industry that are rich in valuable ingredients. The utilisation of these two by-products is becoming increasingly possible as consumer awareness of upcycling increases. The biological activities of grape pomace extract (GPE) are diverse and depend on its bioavailability, which is influenced by processes in the digestive system. In this work, goat whey protein (GW) was used as the primary coating to protect the phenolic compounds of GPE during the spray drying process. In addition, trehalose (T), sucrose (S), xylose (X) and maltodextrin (MD) were added to the goat whey proteins as co-coatings and protein stabilisers. All spray drying experiments resulted in microcapsules (MC) with high encapsulation efficiency (77.6—95.5%) and yield (91.5—99.0%) and almost 100% recovery of phenolic compounds during the release test. For o-coumaric acid, the GW-coated microcapsules (MC) showed a bioavailability index of up to 731.23%. A semi-crystalline structure and hydrophilicity are characteristics of the MC coated with 10% T, S, X or 5% MD. GW alone or in combination with T, S, MD or X has proven to be a promising carrier for polyphenols from grape pomace extract and ensures good bioavailability of these natural antioxidants.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

Quaking aspen (Populus tremuloides Michx.) is an important deciduous species in western U.S. forests. Existing maps of aspen distribution are based on Landsat imagery and often miss small stands (<0.09 ha or 30 m²), which rapidly regrow when managed or following disturbance. In this study, we present methods for deriving a new regional map of aspen forests using one year of Sentinel-1 (S1) and Sentinel-2 (S2) imagery in Google Earth Engine. We assessed the annual phenology of aspen in the Southern Rockies and leveraged the frequent temporal resolution of S1 and S2 to create ecologically relevant seasonal composites. Additionally, we derived spectral indices and radar textural features targeting the canopy structure, moisture, and chlorophyll content. Using spatial block cross-validation and Random Forests, we assessed the accuracy of different scenarios and selected the best performing set of features for classification. Comparisons were then made with existing landcover products across the study region. The resulting map improves on existing landcover products in both accuracy (average F1-score = 93.1%) and detection of smaller forest patches. These methods enable accurate mapping at spatial and temporal scales relevant to forest management for one of the most widely distributed tree species in North America.

Slot-die coatings are advantageous when used for coating large-area flexible devices; in particular, the coating width can be controlled, and simultaneous multi-layer coatings can be processed. Till date, the effects of ink widening and coating gap on the coating thickness have only been considered in a few studies. To this end, we developed two mathematical models to accurately estimate the coating width and thickness considering these two effects. We used root mean square deviation (RMSD) to experimentally verify the developed method. The coating width was seen to increase and the coating thickness was seen to decrease when the coating gap was increased. Experimental results showed that the estimation performances of the coating width and thickness models were as high as 98.46 % and 95.8 %, respectively. We believe that the developed models can be useful for determining the coating conditions according to the ink properties to coat a functional layer with user-defined widths and thicknesses in both lab- and industrial-scale roll-to-roll slot-die coating processes.

Porosity in plasma sprayed coatings is vital for most engineering applications. It is either advantageous or disadvantageous depending on the functionality of the coating and the immediate working environment. Consequently, the formation mechanisms and development of porosity has been extensively explored to find out modes of controlling porosity in plasma sprayed coatings. In this work, a comprehensive review of porosity on plasma sprayed coatings is established. The formation and development of porosity on plasma sprayed coatings are governed by set spraying parameters. Optimized set spraying parameters have been used to achieve the most favorable coatings with minimum defects. Even with the optimized set spraying parameters, defects like porosity still occur. Here, we discuss other ways that can be used to control porosity in plasma sprayed coating with emphasis to atmospheric plasma sprayed chromium oxide coatings. Techniques like multi-layer coatings, nano-structured coatings, doping with rare earth elements, laser surface re-melting and a combination of the above methods have been suggested in adjusting porosity. The influences of porosity on properties of plasma sprayed coatings and the measurement methods of porosity have also been reviewed.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

This study aimed to develop multifunctional nanoplatforms for both cancer imaging and therapy using superparamagnetic iron oxide nanoparticles (SPIONs). Two distinct synthetic methods, reduction-precipitation (MR/P) and co-precipitation at controlled pH (MpH), were explored, including the assessment of coating’s influence, namely dextran and gold, on their magnetic properties. These SPIONs were further functionalized with gadolinium to act as dual T1/T2 contrast agents for magnetic resonance imaging (MRI). Parameters such as size, stability, morphology, and magnetic behavior were evaluated by a detailed characterization analysis. To assess their efficacy in imaging and therapy, relaxivity and hyperthermia experiments were performed, respectively. The results revealed that both synthetic methods lead to SPIONs with similar average, 9 nm. Mössbauer spectroscopy indicated that samples obtained from MR/P consist of approximately 11-13% of Fe present in magnetite, while samples obtained from MpH have higher content, of 33%-45%. Despite coating and functionalization, all samples exhibited superparamagnetic behavior at room temperature. Hyperthermia experiments showed increased SAR values with higher magnetic field intensity and frequency. Moreover, the relaxivity studies suggested potential dual T1/T2 contrast agent capabilities for the coated SPpH-Dx-Au-Gd sample, thus demonstrating its potential in cancer diagnosis.

Nano-titanium has excellent corrosion resistance and can be widely used in the field of corrosion resistant coatings. This paper introduces nano-weight titanium modified phenolic resin coatings and their anti-corrosion properties to explore the principle of nano-titanium modification and the mechanism of anti-corrosion to further develop more advanced corrosion resistant coatings. The article uses scanning electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and UV-Vis spectrophotometer to characterise the morphology and structure of the nano-titanium modified phenolic resin coatings and to determine the corrosion resistance properties of the modified phenolic resin coatings. The results show that the 4% nano-titanium modified phenolic resin coating, nano-titanium powder and phenolic resin will maximize the dispersion and combination, and the structure is good; nano-titanium grafted on phenolic resin, the successful preparation of nano-titanium modified phenolic resin; modified nano-titanium added to improve the coating's ability of UV absorption. The corrosion resistance of the coating is much better than that of the unmodified phenolic resin coating.

Advanced Nano structural hard coatings are thin materials films that range in thickness from a few nanometers to a few micrometers and are applied to different surfaces to increase their hardness and wear resistance. Physical vapor deposition (PVD) or chemical vapor deposition (CVD) methods are frequently used to deposit these coatings. These coating’s distinctive characteristics result from their microstructure, which is made up of material columns or grains with a diameter of only a few nanometers. Increased hardness, higher wear resistance, and improved tribological properties result from these short dimensions. In applications with significant wear and/or high contact pressures, such as cutting tools, bearings, and engine parts, the usage of sophisticated Nano structural hard coatings is crucial. Advanced Nano structural hard coatings include, 1. Amorphous carbon coatings with high hardness, low friction, and exceptional wear resistance are known as diamond-like carbon (DLC) coatings. DLC coatings are frequently used in a variety of industries, including the automotive, aerospace, and biomedical ones. 2. Coatings made of titanium nitride (TiN): These metallic coatings have high hardness and wear resistance. Cutting tool, machining, and aerospace industries frequently use TiN coatings. 3. Chromium nitride (CrN) coatings: These coatings have great corrosion resistance, good wear resistance, and high hardness. Cutting tools, gears, and bearings are just a few of the objects that use CrN coatings. 4. Tungsten carbide (WC) coatings: These coatings, which have a high degree of hardness and wear resistance, are frequently employed in cutting tools and other applications that require wear resistance. Advanced Nano structural hard coatings provide many advantages over conventional coatings, including better hardness, increased wear resistance, and improved tribological qualities. The automotive, aerospace, and biomedical industries are just a few that could use these coatings. In this paper the author will explain about the design synthesis and applications of advanced Nano structural hard coating in aerospace and automotive applications.

Even though hard, low friction coatings such as diamond like carbon (DLC) would be beneficial for the per-formance and longevity of rubber seals, a crucial challenge – as graphically illustrated in Figure 1.a – remains. The elastic mismatch of rubber substrate and DLC coating prevents a fracture free coating application. In this work a nature inspired approach (Figure 1.b) is applied to render the stiff coating flexible and resilient to delamination at the same time by direct patterning. Rubber substrates were laser structured with tile patterns and subsequently DLC-coated. Tensile and tribology tests were performed on structured and unstructured samples. Unstructured DLC-coatings showed a crack pattern induced by the coating process, which was further fragmented by tensile stress. Coatings with tile patterns did not experience a further fragmentation under load. During continuous tribological loading, less heterogenous damage is produced for tile structured samples. The findings are ascribed to the relief of induced coating stress by the tile structure, meaning a more resilient coating.

Coating of organic molecules from the solution phase can result in directional crystal growth under certain conditions, even on a smooth isotropic surface and without the need of any kind of graphoexpitaxial preparation of the substrate. Based on reviewing the results from a variety of coating techniques and conditions, we identify the condition that the coating speed should equal the growth speed of the fastest growing crystal plane as crucial for achieving a high degree of directional crystallization.

Background: Nowadays investigations in the field of dental implants engineering are focused on bioactivity and osseointegration properties.Objective: In this study, the oxide-covered titanium was functionalized by vitamin D3 molecules via a simple self-assembly method with the aim to design more corrosion resistant and at the same time more bioactive surface.Methods: Surface properties of the D3-coated titanium were examined by scanning electron microscopy, attenuated total reflectance Fourier transform infrared spectroscopy, and contact angle measurements, while a long-term corrosion stability during immersion in an artificial saliva solution was investigated in situ by electrochemical impedance spectroscopy.Results: Results of all techniques confirmed a successful formation of the D3 vitamin layer on the oxide-covered titanium. Besides very good corrosion resistivity (~5 MΩcm² ) the D3-modified titanium surface induced spontaneous formation of biocompatible bone-like calcium phosphates (CaP).Conclusion: Observed in vitro CaP-forming ability as a result of D3-modified titanium/artificial saliva interactions could serve as a promising predictor of in vivo bioactivity of implant materials.

Organic electrophoretic coatings have gained significant attention due to their ability to provide a uniform and controlled coating thickness, high coating adhesion, and excellent corrosion protection properties. In this work, to investigate the aging behaviors of an organic electrophoretic coating for magnesium alloys, water absorption kinetics curves of the coatings after immersion in 3.5 wt.% NaCl at 20℃ and 40℃ were measured, and parameters such as the saturated water absorption and saturation time of the free film coatings were fitted to determine the densification evolution of the organic coatings. A tensile test was used to test the tensile strength of the organic coating during service to determine the evolution of the strength and toughness of the organic coating. The evolution of wet adhesion of organic coatings with service time was tested by ASTM D4541-02. The impedance spectra of the organic coatings under the above conditions were detected by EIS, and finally, the failure behavior of the organic coatings under immersion was analyzed.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Peri-implantitis occurs at a significant rate, which is the leading cause of implant failure. The main reason for this unwanted complication is bacterial invasion and biofilm formation. To reduce the incidence of peri-implantitis, we constructed a carboxymethyl dextran (CMD) based nanomicelles antibacterial coating on microarc-oxidized titanium (MAO-Ti) surface. After cross-linking, the drug-loaded nanomicelles were spherical with a particle size of 130nm and uniformly dispersed. Zeta potential was negative, and the absolute value was greater than 10 mV, effectively avoiding micelles aggregation. It was observed by dynamic light scattering (DLS) that the stability of nanomicelles was significantly improved after cross-linking. The hemolysis rate of micelles was less than 5%, and the overall survival rate of human umbilical vein endothelial cells was more than 90%. After being coated on MAO-Ti surface, the cumulative drug release rate of drug-loaded nanomicelles reached 86.6% after 360 hours. Fluorescence staining of immobilized bacteria showed more dead bacteria on the coating surface, and the number of live bacteria was significantly reduced. It was concluded that dextran-based nanomicelles, which showed long-term drug release properties and excellent biocompatibility, are potential drug carriers for fabricating antibacterial coating on titanium surfaces.

We demonstrated a new approach to the production of three-dimensional-coated patterns using liquid route. Metallic perovskite oxides were coated onto three-dimensional (3D) microstructured substrates with different aspect ratios. The success of the method relies on the solution viscosity monitored by adding viscous liquid. The process of oxide thin films consists in three steps: preparing the precursor solution, coating the solution by spin-coating process onto three-dimensional-Si substrates and post-annealing. The chemical solution 3D-coating is conformal.

Coating of suitable materials having thickness of few atoms to several microns on a substrate is of great interest to the scientific community. Hard coatings develop under the significant composition of suitable-natured atoms where their force-energy behaviors when in certain transition state favour binding. In the binding mechanism of suitable atoms, electron belonging to outer ring filled state of gas-atom undertakes another clamp of energy knot belonging to outer ring unfilled state of solid-atom. Set process conditions develop the binding of different-natured atoms when processing their suitable composition in a system. Atoms of different nature develop structure in the form of hard coating by locating their ground points between the original ones. Here, gas-natured atoms increase the potential energy under decreasing levitational force of electrons, whereas, solid-natured atoms decrease the potential energy under decreasing gravitational force of electrons. In TiN coating, Ti–Ti atoms bind under the difference of expansion of their lattices, called nets of energy knots, where one atom just lands on the already landed atom. An adhered N-atom to a Ti-atom forms its position among four Ti-atoms where N-atom occupies the interstitial site of Ti-atoms. Two oppositely working force-energy behavior atoms deposit in the form of coating at substrate surface as per set conditions of the process. The rate of ejecting (or dissociating) solid-natured atoms depend on the nature of their source (target), process parameters and processing technique. In random arc-based vapor deposition system, depositing differently natured atoms at substrate surface depends on the input power. In addition to intrinsic nature of atoms, different properties and characteristics of coatings emerge as per engaged forces under their involved energy. The present study sets new trends in the field of coatings involving the diversified class of materials and their counterparts.

In recent years, there has been growing interest in thermal spray techniques using suspension or solution-based coatings. These techniques offer precise control over particle size and microstructure, improving feedstock flowability and allowing for high-quality coatings customization. Spray parameters, such as stand-off distance (SOD) and feedstock flow rate, can alter the performance and characteristics of these coatings. Geothermal power plant heat exchangers often face issues like corrosion, scaling, and fouling. These issues could be mitigated, at least in part, by the use of spray coatings. In this study, TiO2 coatings were applied to a carbon steel substrate using suspension plasma spray (SPS) to enhance the performance of geothermal heat exchanger materials. The impact of SOD (50, 75, and 100mm) and feedstock flow rate (10, 20, and 30 ml/min) on these coatings was examined through various techniques, including SEM, profilometry, XRD, and adhesion testing. The results demonstrated that coatings deposited using 10ml/min feedstock flow rate were well-adhered to the substrate due to efficient melting of coating material but as the SOD and feedstock flow rate increase due to poor thermal and kinetic energy exchange between the torch and feedstock particles, adhesion between coating and substrate decreases. smaller SODs led to more compact coatings, while higher feedstock flow rates increased coating porosity. Smaller SODs and lower flow rates resulted in well-adhered coatings, offering valuable insights for advancing geothermal heat exchanger coatings.

Bioactive surface coatings have retained the attention of researchers and physicians due to their versatility and range of applications in orthopedics, particularly in infection prevention. Antibacterial metal nanoparticles (mNPs) are a promising therapeutic, with vast application opportunities on orthopedic implants. The current research aimed to construct a polyelectrolyte multilayer on a highly porous titanium implant using alternating thin film coatings of chitosan and alginate via the layer-by-layer (LbL) self-assembly technique, along with the incorporation of silver nanoparticles (AgNPs) or titanium dioxide nanoparticles (TiO2NPs), for antibacterial and osteoconductive activity. These mNPs were characterized for their physicochemical properties using quartz crystal microgravimetry with dissipation system, nanoparticle tracking analysis, scanning electron microscopy, and atomic force microscopy. Their cytotoxicity and osteogenic differentiation capabilities were assessed by AlamarBlue and alkaline phosphatase (ALP) activity assays, respectively. The antibiofilm efficacy of the mNPs tested against Staphylococcus aureus. The LbL polyelectrolyte coating was successfully applied to the porous titanium substrate. A dose-dependent relationship between nanoparticle concentration and ALP as well as antibacterial effects was observed. TiO2NP samples were also less cytotoxic than AgNP counterparts, although similarly antimicrobial. Together, these data serve as a proof-of-concept for a novel coating approach for orthopedic implants with antimicrobial and osteoconductive properties.

The microstructure of the coating during hot-dip galvanizing under industrial conditions of two structural steels, a low-silicon ASTM A36 steel and a high-silicon Q345B steel, both of commercial quality, have been characterized for industrial-relevant times. For both cases it is noted that the formation of the Fe-Zn phases begins in early stages during the heating of the steel, a situation in which all the phases are in the solid state. The characterization was carried out through traditional metallographic techniques including SEM-EDS and DRX equipment. The evolution in time of the microstructure of both steels is examined, being able to observe that the mechanism by which silicon accelerates the formation of Fe-Zn phases in galvanizing is related to the change in the energy of the interfaces caused by a silicon accumulation in the liquid phase in contact with the ζ layer. These results provided us with a deeper understanding of the phase evolution in the hot-dip galvanizing of high silicon steels.

Stess in laser cladding coating is an important factor affecting the safe operation of remanufacturing components. Ultrasonic testing has become a hot direction in nondestructive evaluation of stress, because it has the advantages of safety, non-destructive and on-line detection. This paper provides a review of ultrasonic testing for stress in remanufacturing laser cladding coating. It summarizes the recent research outcomes on ultrasonic testing for stress, analyzes mechanism of ultrasonic testing for stress. Remanufacturing laser cladding coating shows typical anisotropic behaviors, the ultrasonic testing signal in laser cladding coating is influenced by many complex factors, such as microstructure, defect, temperature and surface roughness, etc. At present, ultrasonic testing for stress in laser cladding coating can only be done roughly. The paper discusses active mechanism of micro / macro factors to the reliability of stress measurement and the impact of stress measurement to the quality and safety of remanufacturing components. Base on the discussion, the paper proposes strategies for acquisition of nondestructive, rapid and accurate measurement of stress in remanufacturing laser cladding coating.

Electrochemical impedance (EI) measurements were performed to evaluate the nylon 66/-tetra-(para-aminophenyl) porphyrin (H₂T(p-NH₂)PP)/graphene oxide (GO) film coating on stainless steel and compared to the nylon/H₂T(p-NH₂)PP and nylon/GO film samples using 1M H₂SO₄ as electrolyte. The nylon/H₂T(p-NH₂)PP and nylon/GO composite films showed high electrochemical impedance in the order of 109 ohm-cm² and a system controlled by mass transfer, product of a diffusion process at low frequencies with a resistance up to 5 orders of magnitude, indicating the diffusion of protons through the coating and a decrease in the metal dissolution. Otherwise, the nylon/H₂T(p-NH₂)PP/GO film compound evaluated show good ionic conductivity and electrochemical stability in the acid environment, acting porphyrin as a catalyst to the passage of protons through the film, reducing its electrochemical impedance up to 7 orders of magnitude with respect to the compounds nylon/H₂T(p-NH₂)PP and nylon/GO. Likewise, good capacitance values are also shown by modifying the concentrations of porphyrin and GO reinforcing materials. These properties are important for technological applications, such as anticorrosion coating for bipolar plates or membrane in a fuel cell type PEM, super-capacitors, etc.

This paper presents the results of laboratory tests of CFRP (carbon fibre-reinforced polymer) laminates, which allowed the development of numerical material models. The obtained data were used in a further stage to perform numerical simulations of four variants of medical tabletops differing, among other features, in the shape of the cross-section. Maximum deflections and effort in the composite material were analyzed. The final step was to perform a laboratory test for one of the tabletop versions, the results of which confirmed the correctness of the numerical calculations. This work is aimed at both researchers and designers involved in the practical application of fibre-reinforced polymer matrix composites.

In this work, we describe the optimization of carbon-based electrodes employed in Bio-Electrochemical Systems (BES) by the deposition on commercial carbon paper electrodes of nanostructured layers of poly(3,4-ethylene-dioxy-thiophene) poly(styrene-sulfonate) (PEDOT:PSS) via Ultrasonic Spray Coating (USC). This innovative application of USC allowed us to demon-strate that uniform and controlled depositions of PEDOT:PSS can be successfully obtained on car-bon-based electrodes. We characterized the morphology and verified the spatial uniformity of depositions via scanning electron microscopy and Raman spectroscopy. Electrochemical charac-terizations on fabricated electrodes demonstrated a more than two-fold increase in electrochemi-cal active surface area with respect to bare carbon paper. A lab-scale experiments on BES was performed selecting Microbial Fuel Cells (MFCs) as the reference devices. Devices featuring USC-deposited PEDOT:PSS electrodes showed a three-fold higher Energy recovery with respect to con-trol cells, reaching a maximum value of (13 ± 2) J·m−3. Furthermore, the optimal PEDOT:PSS con-centration for the MFCs improvement is in line with the values reported in the literature for other deposition methods. In conclusion, this work demonstrates that USC is a promising technique for application in BES.

The application of chitosan and alginate coatings for Ready-to-Eat (RTE) baked fish product were studied. An experimental design was used to investigate the effect of coating polysaccharide concentration and glycerol addition on the safety (microbial growth), and quality (water loss and lipid oxidation) of RTE seafood product under optimal, and abused storage conditions. The results showed that a chitosan coating with 1% (w/v) chitosan in 1% (v/v) acetic acid, and 15% (w/w chitosan) glycerol, or 1% (w/v) alginate coating with no glycerol, and no crosslinking showed the best performance in controlling the tested safety and quality parameters. Desirability method was used to identify the shelf life of chitosan, alginate and double coated RTE products. Whereby, chitosan coated samples showed the best performance with a third fold shelf life extension compared to uncoated products.

Zeolitic imidazolate frameworks (ZIFs) have potential for various gas and ion separations due to their well-defined pore structure and relatively easy fabrication process compared to other metal-organic frameworks. As a result, many reports have focused on preparing polycrystalline and continuous ZIF layers on porous supports. In this study, we investigated how humidity and chamber temperature influence the structure of a ZIF-8 layer prepared by the hydrothermal method. We controlled the chamber temperature (ranging from 50 °C to 70 °C) and relative humidity (ranging from 20 % to 100 %) using a thermos-hygrostat chamber. We found that as the chamber temperature increased, ZIF-8 preferentially grew into particles rather than forming a continuous polycrystalline layer. By measuring the temperature of the reacting solution based on chamber humidity, we discovered that the heating rate of the reacting solution varied with humidity, even at the same chamber temperature. At higher humidity, thermal energy transfer was accelerated as water vapor delivered more energy to the reacting solution. Therefore, a continuous ZIF-8 layer could be formed more easily at low humidity ranges (ranging from 20 % to 40 %), while micron ZIF-8 particles were synthesized at a high heating rate. Our findings suggest that controlling the heating rate of the reacting solution is critical to preparing a continuous ZIF-8 layer, particularly for future scale-up of ZIF-8 membranes.

Time-domain spectroscopy (TDS) in the Terahertz (THz) frequency range is gaining in importance in nondestructive testing of dielectric materials. One application is the layer thickness measurement of a coating layer. To determine the thickness from the measurement data, the refractive index of the coating layer must be known in the surveyed frequency range. For perpendicular incidence of the radiation, methods exist to extract the refractive index from the measurement data itself without prior knowledge. This paper extends these methods for non-perpendicular incidence, where the polarization of the radiation becomes important. Furthermore, modifications considering effects of surface roughness of the coating are introduced. The new methods are verified using measurement data of a sample of Inconel steel coated with yttria-stabilized zirconia (YSZ) and with COMSOL simulations of the measurement setup. To validate the thickness measurements, scanning electron microscopy (SEM) images of the layer structure are used. The results show good agreement with an average error of 1% for the simulation data and under 4% for the experimental data compared to reference measurements.

Integer is either a composite number or a prime number. Therefore, detecting composite numbers is important for solving prime numbers. The study of prime numbers, apart from satisfying human curiosity, can be very important. In this article, the order of composite numbers has been detected. And explained with a simple method and a simple function. And, a method has been developed in which all composite numbers and therefore prime numbers can be determined by using the specified methods, functions and formulas.

In this study, the efficiency of coating (alginate and carrageenan) and osmotic dehydration pre-treatment (NaCl and sucrose) on decreasing oil uptake of potato strips was assessed. It was examined how various pre-treatments affected the sample’s texture, morphology, color and density properties as well as their moisture content and effective moisture diffusion coefficient (Deff). Results showed that NaCl osmotic dehydration pre-treatment and sucrose solution decreased oil uptake by 30.76% and 41.75%. This is attributed to moisture removal increasing caused by improving dielectric properties. Osmotic dehydration and coating pre-treatment frequently enhanced product shrinkage, browning index, a* and ∆E. Conversely, density, lightness, breaking force, Deff and b* decreased. In control samples, SEM revealed a severely damaged internal structure in comparison to a tissue homogenous layer produced by coating. For moisture loss and oil uptake, the coefficient of determination (R2) and root mean square error (RMSE) of eight empirical models were compared. Finally, the Dehghannya and Krokida model (moisture loss) and the Movahhed and Naghavi model (oil uptake) were found the best fit to the experimental data. Although coating pre-treatment and osmotic dehydration can be used as an alternate de-oiling approach for potato chips, the mechanism of oil uptake reduction differ.

Using nanoparticles (NPs) in drug delivery has exhibited promising therapeutic potential 13 in various cancer types. Nevertheless, several challenges must be addressed, including the 14 formation of the protein corona, reduced targeting efficiency and specificity, potential immune 15 responses, and issues related to NP penetration and distribution within 3-dimensional tissues. 16 To tackle these challenges, we have successfully integrated iron oxide nanoparticles into 17 neuroblastoma-derived extracellular vesicles (EVs) using the parental labeling method. We first de- 18 veloped a tissue-engineered (TE) neuroblastoma model, confirming the viability and proliferation 19 of neuroblastoma cells for at least 12 days, supporting its utility for EV isolation. Importantly, EVs 20 from long-term cultures exhibited no differences compared to short-term cultures. Concurrently, 21 we designed Rhodamine (Rh), Polyacrylic acid (PAA)-functionalized magnetite nanoparticles 22 (Fe3O4@PAA-Rh) with high crystallinity, purity, and superparamagnetic properties (average size: 23 9.2 ± 2.5 nm). We then investigated the internalization of Fe3O4@PAA-Rh nanoparticles within 24 neuroblastoma cells within the TE model. Maximum accumulation was observed overnight while 25 ensuring robust cell viability. However, nanoparticle internalization was low. Taking advantage of 26 the enhanced glucose metabolism exhibited by cancer cells, glucose (Glc)-functionalized nanoparti- 27 cles (Fe3O4@PAA-Rh-Glc) were synthesized, showing superior cell uptake within the 3D model 28 without inducing toxicity. These glucose-modified nanoparticles were selected for parental labeling 29 of the TE models, showing effective NPs encapsulation into EVs. 30 Our research introduces innovative approaches to advance NPs delivery. By partially addressing 31 the challenges associated with 3D systems, optimizing internalization, and enhancing NPs stability 32 and specificity through EV-based carriers. Also, our findings hold the promise of more precise and 33 effective cancer therapies while minimizing potential side effects.

Laser heat treatment is applied after coating. Evaluation of the results was performed by studying the microstructures by metallographic, SEM/EDX microscopy and the mechanical properties were obtained by microscopic hardness and abrasion resistance. The objective of this study was to investigate the effect of laser heat treatment on the wear resistance of metal coatings. The results show the influence of the microstructure and chemical composition of the electrodes used on the micro-hardness and wear resistance of the metal coatings.

The aim of the study was to find the effect of polyethylene (PE) coatings on the short-circuit current of silicon photovoltaic cells covered with glass, in order to improve the short-circuit current of the cells. Various combinations of PE films (thicknesses ranging from 9 to 23 µm, number of layers ranging from 2 to 6) with glasses (greenhouse, float, optiwhite and acrylic glass) were investigated. The best current gain of 4.05% was achieved for the coating combining a 1.5 mm-thick acrylic glass with 2 × 12 µm-thick PE films. This effect can be related to the formation of an array of micro-wrinkles and micrometer-sized air bubbles with a diameter of 50 to 600 µm in the films, which serve as micro-lenses and enhance light trapping.

Biocidal compositions based on interpolyelectrolyte complexes and a low molecular weight antibiotic can become a promising material for creating biocidal coatings, as they combine wash-off resistance and dual biocidal action due to the biocide and the polycation. Molecular mass characteristics of polymers play essential role in physics and mechanical properties of the coatings. In this work, the properties of polydiallyldimethylammonium chloride (PDADMAC) coatings of various molecular weights are investigated and assumptions are made about the optimal molecular weight needed to create antibacterial compositions. To study the resistance to washing off and moisture saturation of the coatings, the gravimetric method was used, the adhesive properties of the coatings were studied by dynamometry. It has been established that an increase in molecular weight affects the wash-off resistance of coatings, but does not affect moisture absorption and adhesion mechanics of coatings. All samples of PDADMAC were demonstrated to exhibit the same antibacterial activity. Thus, when developing systems for creating antibacterial coatings, it must be taken into account that in order to create stable coatings. The requirement to use PDADMAC with a high degree of polymerization is necessary for control the desorption of coating during wash off-but not mandatory for the control of mechanical and antibacterial properties of the coating.

A phosphate/molybdate and cerium-modified phosphate/molybdate conversion coatings were deposited on a carbon steel surface and their protective and self-healing abilities were evaluated. Surface morphology and inner structure of the coatings were examined using FE-SEM-FIB and TEM techniques, chemical composition and element distribution depth profiles in conversion layers were determined using EDX measurements, whereas XPS was applied for the analysis of Mo and Ce oxidation states. Voltammetric measurements and EIS were performed to assess the corrosion behavior of the samples. The higher protective and stronger self-healing abilities were found for phosphate/molybdate/cerium conversion coating deposited in a sulphate-containing solution. This was attributed to higher values of both: total cerium and Ce(IV) content in the conversion layer as well as to lower number of structural defects in the coating. It was demonstrated that the micro-structural characteristics of protective coatings are also important in determining self-healing abilities.

Cathode materials play a key role in the development and application of lithium-ion batteries, but the unfavorable factors such as structural phase transformation and low conductivity in the cycling process restrict the further improvement of battery performance, so the development and modification of high-performance cathode materials is a current research hotspot. LiNixCoyMn1-x-yO2(x≥0.6), a high-nickel cathode material, has the advantages of high platform potential, high energy density and low cost, and is an ideal material to achieve the goal of 300 Wh kg-1 and above for batteries. However, its poor thermal stability, poor interface stability, safety and life cannot meet the requirements of current power batteries. In this paper, the research status of high-nickel cathode materials is introduced, including bulk doping and surface coating, and the modification method of doping and coating integration is also introduced. Finally, we put forward the prospect of the future development trend of high-nickel cathode materials.

In this study, the potential of Fe3Al coating material as an environmentally friendly alternative to coatings containing critical elements for brake discs was investigated. A buffer layer of Cr-Mo steel (Ferro 55) was applied to enhance coating quality and prevent the formation of hot cracks during solidification. Microstructural analysis of the cross-section of the coating showed that the buffer layer diffused into the Fe3Al coating, forming a combination of Fe3Al, Fe, and Fe3AlC0.5 phases. The tribological properties of the Fe3Al coating were evaluated by pin-on-disc tests using two different copper-free friction materials extracted from commercial brake pads. The wear results showed a coefficient of friction comparable to that of an uncoated disc, but with a reduction in Particulate Matter (PM) emissions, an interesting aspect that is gaining increasing importance in view of the upcoming international standards..

In the present study, a nanostructured FeAl coating was prepared by cold spraying of ball milled powder. Annealing treatment was applied to the coating to investigate its effect on the microstructure, phase structure and microhardness of the cold-sprayed nanostructured FeAl coating. The results showed that the FeAl phase was kept unchangeable when the coating annealed at the temperature above 500oC. Annealing temperature significantly influenced the microstructure and microhardness of cold-sprayed FeAl coating. With raising annealing temperature, the lamellar structure in the as-sprayed coating disappeared and a dense coating microstructure with fully bonding of deposited particles at their interfaces was achieved after annealing at 950oC. Nanograin growth of the FeAl phase occurred at an annealing temperature higher than 800oC. The microhardness of cold-sprayed FeAl coating remained about 400 Hv0.1 at the annealing temperature below 800oC and decreased to 300 Hv0.1 at 1100oC.

The organic coating of bridge steel girders is subjected to physical scratches, corrosion, and aging in natural weathering. The breakdown of the coating may cause serviceability and safety problems if left unnoticed. A hyperspectral imaging method is proposed to detect the condition of steel coatings based on coating-responsive features in reflectance spectra. A field test was conducted on the real-world bridge which shows obvious signs of degradation. The hyperspectral signature enables an assessment of the coating health and defect severity. The results indicated that the coating scratch can be effectively located in the domain of a hyperspectral image and the scratch depth can be determined by mapping a scratch depth indicator (SDI=R532nm / R641nm). Rust sources and products in steel girders can be identified by the unique spectral signatures and the rust stains (and thus stain areas) scattered on the coating can be pinpointed at pixel level by the corrosion rust indicators. The chemical integrity of a topcoat is demonstrated by the short-wave infrared spectroscopy and the topcoat degradation can be evaluated by the absorption at 8000 cm-1 and 5850 cm-1.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

Abstract composite silver nanoparticles were synthesised using melanin broth and Arabic gum as a reducing and binding agent. The reactions are carried out with water because it is a non-hazardous solvent. The produced composites either had specified diameters (average diameter of 50 nm) with high silver loading or lower loading composites with tuneable morphologies and electrical properties. UV-IR, gamma, and conventional light are used to characterise the synthesised composite silver nanoparticles. Furthermore, measurements are carried out of the dielectric constant, refractive index, energy gap, optical and electrical conductivities, and refractive index coefficients. The silver nanoparticle formation was validated by UV-Vis measurement of the sample, which demonstrated a distinct peak at a wavelength of 420 nm. The characteristics of the composite silver nanoparticles are also quantified using several methods, including XRD, SEM, and particle size analysis.

Metal matrix composite are used in such fields of technology, such as: aerospace, electronics, energy, industry, defense, automotive, aviation, shipbuilding, and more. Composite coatings of ceramic - metals is used primarily to enhance the durability of machine parts. Therefore, new materials are permanently looked for, what has resulted in the past in development of composite materials. The coatings dispersed are consisting of metallic matrix (metals and their alloys) and small non-metallic particles. The deposition of ceramic particles simultaneously with metallic matrix leads often to composite coatings possessing properties much better than those of metallic coating. The nickel and less often, other iron group elements are usually used as a matrix and Al2O3 as tough particles. The welding technology of applying alloy and composite coatings is widely used. The technology of infrasound thermal spraying of metal matrix composite coatings was presented. It is a simple technology and a very useful one in ship machinery regeneration during the cruise craft (e.g. internal combustion engines, torque pumps, separators). The metal matrix composite coatings must undergo finishing due to high surface roughness after application. In the article to used finishing by plastic working and machining of coatings nickel matrix composite was proposed.

A microstructure-based model is developed to study the effective anisotropic properties (magnetic, dielectric or thermal) of two phase particle-filled composites. The Green’s function technique and the effective field method are used to derive theoretically the homogenized (averaged) properties for a representative volume element containing isolated inclusion and an infinite, chain-structured particles. Those results are compared with the FE approximations conducted for the assumed representative volume element. In addition, as a special case, the Maxwell–Garnett model is retrieved when particle interactions are not taken into consideration. We shall also give some information on the optimal design of the effective anisotropic properties taking into account the shape of magnetic particles.

In this work, a novel heterojunction based on ZnSnO3/ZnO nanofibers was prepared using electrospinning method. The crystal, structural and surface compositional properties of sample based on ZnSnO3 and ZnSnO3/ZnO composite nanofibers were investigated by X-ray diffractometer (XRD), Scanning electron microscope (SEM), X-ray photoelectron spectrometer (XPS) and Brunauer-Emmett-Teller (BET). Compared to pure ZnSnO3 nanofibers, the ZnSnO3/ZnO heterostructure nanofibers display high sensitivity and selectivity response with fast response towards ethanol gas at low operational temperature. The sensitivity response of sensor based on ZnSnO3/ZnO composite nanofibers were 19.6 towards 50 ppm ethanol gas at 225°C, which was about 1.5 times superior than that of pure ZnSnO3 nanofibers, which can be owed mainly to the presence of oxygen vacancies and the synergistic effect between ZnSnO3 and ZnO.

The unique porous crystal structure of zeolite offers various important utilizations, it is one of the considerations in selecting zeolite at this study as component of composite for restraining noise. It so happens, previous experiments show that banana stem has porous structure, fibrous, high flexibility and can be applied as material for many various products including as component of acoustic material. The combination of both is alleged that it has capability in absorbing noise. This paper presents an investigation on the composite that it was synthesized of Activated Zeolite and Banana Stem Fibre in various weight for determining its sound absorption coefficient alpha (a). Activating natural zeolite was conducted by using 6M HCl in order for enlarging zeolite pores. The sound absorption coefficient was measured in the frequency range between 125 Hz up to 6000 Hz. The results show that the different weight of banana stem fibre as component of the synthesized composite affects the value of alpha and shifts the frequency area.

Due to its potential harm to space payload, microwave corona breakdown of microstrip circuits has attracted much attention. This work describes an efficient way to suppress corona breakdown. Since corona breakdown threshold is determined by the highest electric field intensity at the surface of microstrip circuits, lacquer coating with thickness of tens of microns is sprayed on the top of microstrip circuits. The applied dielectric coating is used to move the discharge location away from circuit’s surface which is equivalent to reduce the highest electric field intensity on the in-terface of solid/air of the circuit and thus results into higher breakdown threshold. Two designs of classic coupled-line band-pass filter were used for verification. Corona experimental results at 2.5 GHz show that, in the interested low pressure range (100 to 4500 Pa), 5.3 dB improvement of mi-crowave corona breakdown threshold can be achieved for a filter with narrowest gap of 0.2 mm while its electrical performances like insertion loss, Q-factor are still acceptable. A threshold improvement prediction method is also presented and validated.

The kinetic analysis of octogen coating with a polyurethane base containing hydroxyl-terminated polybutadi-ene (HTPB) was investigated using infrared spectroscopy. The coating process involved a solvent method, where octogen and liquid polyurethane were mixed, the solvent was evaporated, and curing took place at an elevated temperature. The ratio of HTPB to diisocyanate was equimolar. Initially, the curing process occurred in the solvent system, followed by further curing in the bulk system. The kinetic analysis was performed using a modified diffusion-autocatalytic model, which includes non-catalytic, autocatalytic, and diffusion compo-nents. This model was compared with others during the bulk reaction and proved to be effective in correcting errors, particularly in the gel time region. Thermodynamic parameters were evaluated using the Arrhenius and Eyring equations. The reaction rate was initially controlled by chemical reactivity, but after the gel time, diffusion became the controlling factor. In the HTPB-TDI system, both the non-catalytic and autocatalytic parts decreased with increasing temperature, while diffusivity increased. It is worth noting that diffusivity is temperature-dependent. Different diisocyanates, namely toluene diisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HMDI), were studied, revealing that HMDI exhibited higher reactivi-ty than TDI and IPDI. The catalyst effect on reaction rate HTPB-TDI system is investigated. Catalysts adding (0.1%) to HTPB-TDI system is really decrease their activation energy by efectivity DBTL>FeAA>TPB. Catalyst not change their diffusivity.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

Blackberry is a fruit that has high nutritional value, a factor that has expanded its consumption worldwide. However, due to the fragility of the fruits and the high incidence of postharvest diseases, the fruits have a short shelf life. Thus, the objective of this study was to evaluate whether the application of coatings based on microfibrillated cellulose (NC) and lemongrass essential oil (EO) nanoparticles can prolong the shelf life of blackberry fruits after harvest. EO-coated blackberry fruits at nanocellulose concentrations were analyzed as follows: 0; 0.2; 0.4; 0.6 and 0.8%, in addition to the control treatment of which neither essential oil nor nanocellulose was used, for each treatment five repetitions were used. The fruits were analyzed soon after the application of the cover and at three and six days after storage. Fruit quality was assessed by soluble solids (SS), titratable acidity (TA), pH, fresh weight loss (FWL) and colorimetric parameters such as luminosity, hue angle and fruit peel chroma. Coating on EO (1000 ppm) blackberries combined with NC at concentrations of 0.2, 0.4 and 0.6% is promising in preserving blackberry fruits and reducing the process color reversal, up to six days of storage. The 0.4% NC + 1000 ppm EO conjugated coating showed no SS changes in blackberry fruits during the six days of storage.

An ethanol vapor sensor based on a microfiber with quantum-dots (QDs) gel coating is proposed and demonstrated. The QDs gel was made from UV glue as the gel matrix and the CdSe/ZnS QDs with a concentration of 1mg/mL. The drawing and coating process were conducted by using a simple and low-cost home-made system. The bending, ethanol sensing, temperature response and time response tests were carried out, alternatively. The experimental results show that the fabricated sensor has a high sensitivity of -3.3%/ppm, a really low temperature cross-sensitivity of 0.17 ppm/℃ and a fast response time of 1.1s. The robust structure with ease of fabrication and excellent sensing performance render it a promising platform for real ethanol sensing application.

Abstract: This work for the first time investigated the densification of multi-doping zirconia ceramic body with organic coating powders for solid electrolyte of solid oxide fuel cells via online imaging technology. The densification results show the initial stage plays a key role in the sintering. It can be found the covered organic PVA (polyvinyl acetate) supplies a potential kinetics to the initial densification during sintering. As a result, a kinetic function of densification in the initial stage was suggested. Furthermore, a novel sintering model with six sub-stages is developed for polycrystalline zirconia ceramics. The findings would be a valuable reference for predicting final temperature of sintering, the equivalent strain during the sintering process, as well as optimizing the densification behavior.

To prepare an edible coating with a good preservative effect on sweet cherries, carboxymethyl chitosan (CMCS) and gelatin (GL) were selected as the film-forming matrix in this experiment, and CaCl2 and ascorbic acid (AA) were added as crosslinking agents and antioxidants, respectively. First, the film was prepared by the casting method, and the film formula with better mechanical and barrier performance was filtered out by one-factor and response surface optimization test, and the differences in the preservation effect of different film formulations (CMCS-GL, CaCl2- CMCS-GL, AA -CaCl2- CMCS-GL) on sweet cherries were compared. and then the different film formulations were compared. The difference in film formulation on the preservation effect of sweet cherries was investigated. The results showed that the optimal formulation for an edible film based on CMCS-GL with good performance was CMCS: GL (w:w)=2:1, with the additional amount of 1% glycerol, 2% CaCl2, 0.1% Tween-20, 2% AA, the tensile strength, elongation at break, oxygen permeability and water vapor permeability of the film obtained with this formula were: 16.28 MPa, 71.46%, 1.39×10-12 g- cm/(cm2-s-Pa), 5.10×10-11 cm3-cm/(m2-s-Pa), respectively. In the preservation of sweet cherries, all three film formulations effectively reduced the rotting rate and weight loss during storage while preserving the high hardness and skin color of the fruit. Among them, the formulation AA -CaCl2- CMCS-GL showed the best preservation effect and can be used as a new method for postharvest preservation of sweet cherries.

Current methods for the hardening step of functional coatings over different materials imply the use of high temperatures, high energy consumption or long periods of time, which have repercussions on the speed and cost of the product. We report here a simple and low cost methodology for the functionalization of low cost stainless steel, which is modular, depending of the functionality pursued: a levelling layer for smooth the surface of the material, an “easy to clean” property, or both of them. The research is based on sol-gel coatings cured under UV light without requiring high thermal hardening processes making it applicable to plastics and other sensible materials and possessing high chemical and thermal stability. The film ensures lower processing costs, and higher rates of hardening if the adequate medium-pressure lamps are employed. This formulation is also well defined for scaling up the process, so it is possible to perform a continuous coating in large areas by employing mild processing conditions (low temperature, atmospheric pressure). In addition, the sol gel solution was fully characterized and studied in order to guarantee a long service life before deposition, with a focus on industrial applications in the domestic sector.

Ultra-high temperature oxidation-resistant alloys (UTORAs) have received a lot of attention due to the increased research demand for deep space exploration around the world. But UTORAs have the disadvantages of easy oxidation and chalking. So, in this study, a UTORA was prepared by hot-press sintering on VZrHfNbTa (HEA) substrate coated with hafnium. The bonding mechanism, resistance to high-temperature oxidation, and hardness of the sample tests were carried out. The results show that zirconium in the matrix will diffuse into the hafnium coating during the high-temperature sintering process and form the HfZr alloy transition layer, the coating thickness of the composite is about 120 μm, and the diffusion distance of zirconium in the hafnium coating is about 60 μm, this transition layer chemically combines the hafnium coating and the HEA substrate into a monolithic alloy composite. The results of high-temperature oxidation experiments show that the oxidation degree of the hafnium-coated VZrHfNbTa composite material was significantly lower than that of the VZrHfNbTa HEA after oxidation in air at 1600 °C for 5 h. The weight gain of the coated sample after oxidation is 56.56 mg/cm2, which was only 57.7 % compared to the weight gain of the uncoated sample (98.09 mg/cm2 for uncoated), and the surface of the uncoated HEA showed obvious dents, oxidation, and pulverization occurred on the surface and interior of the sample. In contrast, the coated composite alloy sample mainly underwent surface oxidation sintering to form a dense HfO2 protective layer, and the internal oxidation of the hafnium-coated VZrHfNbTa composite alloy was significantly lower than that of the uncoated VZrHfNbTa HEA.

In this review, several cost-effective thin-film coating methods which include dip-coating, spin-coating, spray-coating, blade-coating, and roll-coating are presented. Each method has its set of advantages and disadvantages depending on the type of application. Not all of them are appropriate for large-scale production due to their certain limitations. That is why the coating method should be selected based on the type and size of substrate including the resolution of the required thin-films. The sol-gel method offers several benefits, such as simplicity in fabrication, excellent film uniformity, the capacity to cover surfaces of any size and over vast areas, and a low processing temperature. Nevertheless, these coating methods are somewhat economical and well managed in low-budget laboratories. Moreover, the produced thin-films are homogeneous and have low-surface roughness. Furthermore, some other thin-film deposition methods such as physical vapor deposition (PVD) and chemical vapor deposition (CVD) are also discussed. Since CVD is not restricted to line-of-sight deposition, a characteristic shared by sputtering, evaporation, and other PVD processes, many manufacturing methods favor it. However, these techniques require sophisticated equipment and cleanroom facility. We aim to provide the pros and cons of thin-film coating methods and let the readers decide the suitable technique for their specific application.

In this article, we show theoretically and experimentally the formation of spin-waves band gaps in a magnonic crystal that was implemented by the deposition of periodic micro-structured strips of magnetite nanoparticles. A theoretical model describing the spectra of the transmitted spin-waves bandgaps is proposed. This is achieved using a simple model based on microwave transmission line theory and considering the presence of micro-structured strips of magnetite nanoparticles on the surface. Such magnonic crystal of equally spaced micro-structured strips of magnetite nanoparticles on the surface of an yttrium iron garnet thin film has been implemented and measured. The periodic micro-structured nanoparticles are deposited on the surface of such yttrium iron garnet single-crystal film grown on a gallium-gadolinium garnet substrate via dip-coating technique. Propagation of magnetostatic surface spin-waves is studied and it is shown that the presence of such periodic structure leads to the formation of spin-wave band gaps in the transmission characteristics. The spin-wave detection has been carried out using a pair of microwave antennas and a vector network analyzer. The results show that the periodic structure formed by the magnetite strips modifies the spectra of the transmitted spin waves producing band gaps.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

The maintenance of high quality standards for prolonging shelf life of fruit and maintaining sensory and nutritional quality is a priority the horticultural products. The aim of this work was to test the effectiveness of a single treatment of edible coating based on Aloe arborescens and a combined treatment of 1-Methylcycyclopropene and edible coating to prolong the shelf-life of "Settembrina" white flesh peach fruit. White flesh peach fruit were harvested at the commercial ripening stage and treated with edible coating (EC) or 1-MCP +EC and stored for 28 days at 1°C. After 7, 14, 21 and 28 days fruits were removed from cold storage, transferred at 20°C and then analyzed immediately (cold out) and after 6 days (shelf life) to evaluate the combined effect of cold storage and room temperature. Weight loss, physical, chemical and sensory parameters were measured. Fruit treated with EC and 1-MCP +EC kept their marketing values better than CTR after 14 days of storage and 6 days of simulated shelf life, in terms of flesh firmness, total soluble solids and titratable acidity as well as sensory parameters. After 21 days of storage, all treatments showed a deterioration of the quality parameters. The single and combined application of Aloe-based coating (with 1-MCP) slowed down the maturation processes of the fruit, limited the weight loss and preserved its organoleptic characteristics.

In recent years extensive studies have been continuously undertaken on the design of bioactive and biomimetic dental implant surfaces due to the need for improvement of the implant-bone interface properties. In this paper, the titanium dental implant surface was modified by a bioactive vitamin D3 coating prepared by self-assembly process. Surface characterization of the modified implant was performed by field emission scanning electron microscopy (FE-SEM), attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), and contact angle measurements (CA). Implant’s electrochemical stability during exposure to an artificial saliva solution was monitored in situ by electrochemical impedance spectroscopy (EIS). Experimental results obtained were corroborated by means of quantum chemical calculations at the density functional theory level (DFT). The formation mechanism of the coating onto the titanium implant surface was proposed. During a prolonged immersion period, the bioactive vitamin D3 coating effectively prevented the underlying titanium from corrosive attack (polarization resistance in order of 10⁷ Ω cm²) with ~95% protection effectiveness.

We give a bilocal field theory description of a composite scalar with an extended binding potential, that reduces to the Nambu–Jona–Lasinio (NJL) model in the pointlike limit. This provides a description of the internal dynamics of the bound state and features a static internal wave-function, ϕ(⃗r), in the center-of-mass frame that satisfies a Schr¨odinger-Klein-Gordon equation with eigenvalues m2. We analyze the “coloron” model (single perturbative massive gluon exchange) which yields a UV completion of the NJL model. This has a BCS-like enhancement of its interaction, ∝ Nc the number of colors, and is classically critical with gcritical remarkably close to the NJL quantum critical coupling. Negative eigenvalues for m2 lead to spontaneous symmetry breaking, and the Yukawa coupling of the bound state to constituent fermions is emergent.

Premature failure and degradation of layers are the main problems for transportation infrastruc-ture. Addressing these issues necessitates implementing structural health monitoring (SHM) for transportation layers. This strategic approach is instrumental in mitigating maintenance expenses, prolonging the operational lifespan, and preventing accidents resulting from abrupt layer col-lapse. To this end, this research investigated the stress/strain and damage detection capabilities of a self-sensing cementitious composite developed for potential utilization in the construction of an intelligent subgrade layer. The prepared self-sensing cementitious composite consisted of 10% cement and hybrid conductive fillers, including multiwalled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) in sand. Initial findings reveal that the electrical resistivity of the composite is significantly affected by the concentration of MWCNTs/GNPs, with a minimum concentration of more than 0.5% needed to achieve a responsive cementitious composite. More-over, the piezoresistive analysis indicates that an increase in the concentration of MWCNTs/GNPs and stress levels leads to an improvement in the stress/strain sensing perfor-mance. When the self-sensing cementitious composite is subjected to equivalent stress levels, variations in the FCR exhibit an increasing trend with decreasing resilient modulus, stemming from a decrease in stiffness due to the increased concentration of MWCNTs/GNPs. Additionally, the EIS analysis demonstrates a contraction for the Nyquist curves under compressive ramp loading prior to failure, followed by the expansion of these curves postfailure. Scanning electron microscopy (SEM) images visually showcase the bridging effects of MWCNTs and the filling ef-fects of GNPs within the composite structure.

This study demonstrates the successful synthesis of Ni/Y2O3 nanocomposite particles through the application of ultrasound-assisted precipitation using the Ultrasonic Spray Pyrolysis technique. The particle size was predicted accurately using a modified equation, and they were collected in a water suspension with Polyvinylpyrrolidone (PVP) as the stabiliser. The presence of the Y2O3 core and Ni shell was confirmed with Transmission Electron Microscopy (TEM) and with electron diffraction. The TEM observations revealed the formation of round particles with an average diameter of 466 nm, while the lattice parameter on the Ni particle’s surface was measured to be 0.343 nm. The Ni/Y2O3 nanocomposite particle suspensions were lyophilized, to obtain a dried material that was suitable for embedding into a Polylactic acid (PLA) matrix. The resulting PLA/Ni/Y2O3 composite material was successfully extruded successfully, so that a 3D printed technology Fused Filament Fabrication could be used further for the production of tensile test tubes. The tensile tests showed that the addition of lyophilised Ni/Y2O3 into the PLA matrix decreased the tensile strength by 21.8 %, while the tensile modulus was not influenced. Dynamic Mechanical Analysis (DMA) showed that the addition of the Ni/Y2O3 particles increased the glass transition temperature by 5 °C, and increased the storage modulus in the glass transition range significantly. These findings demonstrate the potential for utilising Ni/Y2O3 nanocomposite particles in 3D printing applications, and warrant further exploration of their mechanical properties and potential applications in various fields.

Fluorescent hydrogels are promising candidate materials for portable biosensors to be used in point-of-care diagnosis because (1) they have a greater capacity for binding organic molecules than immunochromatographic test systems, determined by the immobilization of affinity labels within the three-dimensional hydrogel structure; (2) fluorescent detection is more sensitive than the colorimetric detection of gold nanoparticles or stained latex microparticles; (3) the properties of the gel matrix can be finely tuned for better compatibility and detection of different analytes; and (4) hydrogel biosensors can be made reusable and suitable for studying dynamic processes in real time. Water-soluble fluorescent nanocrystals are widely used for in vitro and in vivo biological imaging due to their unique optical properties, and hydrogels based on them allow preserving these properties in bulk composite macrostructures. Here we review the techniques for obtaining analyte-sensitive fluorescent hydrogels based on nanocrystals, the main methods used for detecting the fluorescent signal changes, and the approaches to the formation of inorganic fluorescent hydrogels via sol–gel phase transition using surface ligands of the nanocrystals.

Carrageenan (car-), used in the pharmaceutical as well as food industry, is marine sulfated polysaccharides. The carrageenan blends (CB) of kappa (κ-), iota (ι-), and lambda (λ-) of 50/50 weight by weight are multipurpose and biocompatible hydrophilic polymers. They were subjected to adsorption of copper (Cu2+) ions. The aim of the study was to conduct extensive rheological and mechanical studies rendering them suitable for biological purposes. The rheology was conducted at various temperatures using a frequency curve, frequency sweep, loss modulus, and storage modulus analysis. Models of rheology like Ostwald, Bingham, and Modified Bingham models were utilized. The rheological results demonstrated non-Newtonian/pseudo-plastic behavior at various temperatures. The models of rheology demonstrated good flow properties and rheological performance of these materials. These materials could be exploited for their application in pharmaceuticals, food, and cosmetics. Thus, our study reflects that these CB can be safely exploited in the healthcare, pharmaceutical, and food industry. However, further studies should be conducted to evaluate their effectiveness in clinical studies.

Electrospinning polymer fibers for is a well-understood process, primarily resulting in random mats or single strands. More recent systems and methods have allowed for the production of nanofiber yarns (NFY) for ease of use in textiles. This paper presents a method of NFY manufacture using a simplified dry electrospinning system to produce self-assembling functional NFY capable of conducting electrical charge. The polymer is a mixture of cellulose nanocrystals (CNC), polyvinyl acrylate (PVA) and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). When treated with Ethylene Glycol (EG) to enhance conductivity, fibers touching the collector plate align to the applied electrostatic field and grow, twisting together as additional nanofiber polymer is added by the jet. The longer the electrospinning continues, the longer and more uniformly twisted the NFY becomes. This process has the added benefit of reducing the electric field required for NFY production from >2.43 kV cm-1 to 1.875 kV cm-1.

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcase a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composite for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the relevance of mycelium-based materials has extended beyond their original fields of microbiology and mycology to architecture.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

Air pollution is related to the development of people's livelihood. As one of the main pollutants in the air, formaldehyde affects people's physical and mental health. In order to remove formaldehyde and better protect the health of residents, it is very necessary to develop efficient adsorption materials. In this study, a cellulose composite aerogel Microcrystalline Cellulose/ N-(2- aminoethyl) -3- aminopropyl methyl dimethoxysilane (MCC/APMDS) modified by APMDS was explored. The pore volume and specific surface area of the modified aerogel decreased, the average pore diameter increased, and the adsorption capacity of formaldehyde was stronger. The adsorption experiment shows that the sample prepared under the conditions of APMDS dosage of 6 wt%, reaction time of 4 h and reaction temperature of 90℃ has the largest average pore size (14.56 nm) and the largest formaldehyde adsorption capacity (9.52 mg/g). The excellent adsorption of the composite aerogel is due to high porosity and rich active amino groups on the surface. This study provides valuable information for the preparation of adsorption materials with high formaldehyde adsorption capacity for air purification.

The main objective of this work is to study the effects of carbon nanotubes (CNT) on the strength and electrical properties of cement mortar. Molecular dynamic simulations (MDS) were carried out for the mechanical and electrical properties of the cementitious composite and the associated mechanisms. To model the atomic structure of the Calcium-Silicate-Hydrates (C-S-H) gel, tobermorite 11Å was chosen. Single-walled carbon nanotubes (SWCNTs) embedded in tobermorite structure were tested numerically. In particular, the effect of the concentration of CNT in cement paste was studied. An innovative experiment of electrical characterization of a cementitious composite of carbon nanotubes has been developed.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

A deep relationship is identified between the Coulomb Force and Gravity. A gravitational constant for strong gravity is calculated from the relationship. The equivalence between mass and charge is explored. Implications are given for the expansion of Einstein's Field Equations to include vector gravity.

The accurate prediction of molecular properties such as lipophilicity and aqueous solubility are of great importance and pose challenges in several stages of the drug discovery pipeline. Machine learning methods like graph-based neural networks (GNNs) have shown exceptionally good performance in predicting these properties. In this work, we introduce a novel GNN architecture, called directed edge graph isomorphism network (D-GIN). It is composed of two distinct sub-architectures (D-MPNN, GIN) and achieves an improvement in accuracy over its sub-architectures employing various learning, and featurization strategies. We argue that combining models with different key aspects help make graph neural networks deeper and simultaneously increase their predictive power. Furthermore, we address current limitations in assessment of deep-learning models, namely, comparison of single training run performance metrics, and offer a more robust solution.

Typhoid fever is a major public health burden which causes substantial global morbidity and mortality due to lack of decisive diagnostic protocols. The capacity of commonly use diagnostic test to validate the absence of typhoid fever is controversial. This study explores to evaluate new techniques for typhoid diagnosis and proposed a harmonised suitable standardized composite reference to be adopted. Published peer-reviewed articles indexed in PubMed, MEDLINE and Google scholar were reviewed for hospital-based studies. This study reveals new typhoid diagnostic techniques such as proteomics, serology, Rapid Diagnostic tests (RDTs), transcriptomics, genomics, and metabolomics. 34.4% of the studies use prospective study design. The study result establishes that, Widal test has a moderate diagnostic accuracy with average percentage sensitivity (52.9%), specificity (54%), positive predictive value (PPV) (56.8%) as well as negative predictive value (NPV) (55.6%) when compared with 29.4%, 28%, 29.5%, and 27.8% of Typhidot respectively. The findings showed a statistically significant difference on the sensitivity between Widal and Typhidot t (40) = 2.639, p = 0.012 at p<0.05 using independent sample t-test. When there is no perfect reference standard that has an optimal diagnostic accuracy, the need for a harmonised suitable standardized composite reference is essential. Hence, this study recommends that, peripheral blood culture with established sensitivity of 60% and Widal test with average sensitivity of 52.9% be adopted as a consensus composite reference standard for typhoid fever diagnosis in other to improve confidence in prevalence estimates.