Metal/metal composites represent a particular class of materials showing innovative mechanical and electrical properties. Conventionally, such materials are produced by severely plastically deforming two ductile phases via rolling or extruding, swaging, and wire drawing. This study presents the feasibility of producing metal/metal composites via a capacitive discharge-assisted sintering process named electro-sinter-forging. Two different metal/metal composites with CP-Ti/AlSi10Mg ratios (20/80 and 80/20 %vol) are evaluated, and the effects of the starting compositions on the microstructural and compositional properties of the materials are presented. Bi-phasic metal/metal composites constituted by isolated α-Ti and AlSi10Mg domains with a microhardness of 113 ± 13 HV_0.025 for the Ti20-AlSi and 244 ± 35 HV_0.025 for the Ti80-AlSi are produced. The effect of the applied current is crucial to obtain high theoretical density, but too high currents may result in Ti dissolution in the Ti80-AlSi composite. Massive phase transformations due to the formation of AlTiSi based intermetallic compounds are observed through thermal analysis and confirmed by morphological and compositional observation. Finally, a possible explanation for the mechanisms regulating densification is proposed accounting for current and pressure synergistic effects.

The paper examines the possibility of increasing the wear and corrosion resistance of a CP-Ti surface by duplex plasma electrolytic treatment (borocarburizing and polishing). The structure and composition of diffusion layers, their microhardness, surface morphology and roughness, wear resistance during dry friction and corrosion resistance in Ringer's solution were studied. The formation of a surface hardened layer up to 200 m thick with a microhardness of up to 950 HV, including carbides and a solid solution of boron and carbon, is shown. Subsequent polishing makes it possible to reduce surface roughness and remove weak areas of the porous oxide layer, which is formed during high-temperature oxidation in aqueous electrolyte vapor during borocarburizing. Changing the morphology and structural-phase composition of the CP-Ti surface helps reduce weight wear by 3 times (the mode of frictional interaction changes from microcutting to oxidative wear) and corrosion current density by 4 times after borocarburizing in a solution of boric acid, glycerin and ammonium chloride at 950 °C for 5 minutes and subsequent polishing in an ammonium fluoride solution at a voltage of 250 V for 3 minutes.

The creep response of commercially pure titanium was investigated in air at 550, 600 and 650°C, to assess the effect of oxidation on the mechanical response. Experiments demonstrated that exposure at high temperature produced a marked reduction of the minimum creep rate under a given applied stress. Microhardness measurements showed that a hardened zone forms in proximity of the surface, due to oxygen penetration into metal. A simplified composite-model was then used to describe the creep response. In this model, the sample consisted of two zones, the hard case, enriched in oxygen, and the soft pure-titanium core, both creeping with similar strain rates. Calculation led to an estimation of the dependence of the minimum creep rate on stress and temperature for the hard high-oxygen zone. The simplified composite-model here presented gave an excellent description of experimental creep data for pure titanium tested in air and also provided a reliable picture of the effect of oxidation on complex Ti-alloys.

The possibility of increasing wear resistance of the CP-Ti surface using a duplex surface treat-ment combining plasma electrolytic nitrocarburizing in a solution of ammonia, acetone and ammonium chloride and subsequent plasma electrolytic polishing is shown. Morphology and surface roughness, structure and microhardness of the modified layer were studied. The correla-tion of weight wear with hardness of diffusion layer at a low processing temperature and thick-ness of oxide layer is established – the largest decrease in weight wear occurs after nitrocarbu-rizing at 750 °C for 5 min (by 4.3 times). The possibility of an additional increase in wear re-sistance by subsequent polishing of the nitrocarburized CP-Ti surface at a voltage of 275–300 V for 3–5 min in chloride and fluoride electrolytes and 5–10 min in a sulfate electrolyte was re-vealed. Under these conditions, the hardened layer is preserved when the porous outer oxide layer is removed. According to the microtopology of the friction tracks, the wear mechanism is estimated as fatigue in dry friction and plastic contact.

The agronomic characteristics of Cenchrus purpureus were assessed through a randomized block experimental design with seven accessions (Taiwan grass, King grass, Elephant grass, Merkeron, CT-115, Purpule grass and Maralfalfa) as treatments and four replications research was carried out at the Instituto Tecnológico Superior de Tantoyuca, in 2019 and 2020, under rainfed conditions. Sowing density was established at 36 tillers in 25 m2. Green and dry matter yield, daily rates of dry matter accumulation in leaves, leaf/stem ratio, height, leaf area index and cutting frequency were assessed. Rainfall amount, temperature, relative humidity and global radiation levels were recorded to assess their effect on the evaluated variables. One-way ANOVA and multivariate analysis techniques, such as multiple linear regression (MLR), Clustering, and Principal component analysis (PCA) with the Statistica V7 software, were used. The leaf area index was greatest (p < 0.05) on the dry season. Green and dry matter yield were greatest in Maralfalfa (p < 0.05). Variation in the results is attributed to weather phenomena; nonetheless, Elephant grass and Maralfalfa showed the highest yields. Quality parameters must be evaluated to identify those grasses with the best attributes.

Abstract: Arranged patterns obtained by ultrafast laser processing on the surface of Ti/Cu/Ti/Si and Ti/Zr/Ti/Si thin film systems are reported. Two differently designed multilayer thin films, Ti/Cu/Ti/Si and Ti/Zr/Ti/Si, were deposited on silicon by the ion sputtering method. The bioactive surfaces on these systems involve the formation of laser-induced periodic surface structures (LIPSS) in each of the laser-written lines of mesh patterns on 5x5 mm areas. The formation of nano- and micro-patterns with an ultra-thin oxide film on the surfaces was used to observe the effects of morphology and proliferation of the MRC-5 cell culture line. To determine whether Ti-based thin films have a toxic effect on living cells, an MTT assay was performed. The relative cytotoxic effect as a percentage of surviving cells showed that there was no difference in cell number between the Ti-based thin films and the control cells. There was also no difference in the viability of the MRC-5 cells, except for the Ti/Cu/Ti/Si system, where there was a slight 10% decrease in cell viability.

The synergistic features of a three-component, photoinitiating system (A/B/C) based on the measured data and proposed mechanism of Liu et al. are analyzed. The co-initiators/additives B and C have dual-functions of : (i) regeneration of photoinitiator A, and (ii) generation of extra radicals for enhanced conversion efficacy (CE). The synergistic effects led to higher CE for both free radical polymerization (FRP) and cationic polymerization (CP). The CE of FRP has 3 terms due to the direct (tyep-I) coupling of the triplet state of A with the monomer (M) and the coupling of the two radicals, R and R', with M. The CE of CP has a transient state proportional to the effective absorption constant (b), the light intensity (I) and initiator concentration (A0), but a steady state is independent of the light intensity (I). For the CE of FRP, the contribution from radical R had two cases: (i) linear dependence on T=bIA0, or (ii) nonlinear square root dependence T0.5. The synergistic effects led to higher conversion of FRP and CP, consistent with the measured results. The theoretically predicted new features include: (i) co-initiator [C] which always enhances both FRP and CP conversions, and (ii) co-initiator [B] which leads to more efficient FRP, but it also reduces CP.

Abstract: Patients with Cleft Lip Palate (CLP) require comprehensive treatment, so the people who take care of them must constantly provide care and support, along with continuous care and support from their caregivers, often extending until youth. The purpose was to compare the Quality of Life (QoL) of caregivers of children with CLP with those without the condition. A cross-sectional paired study was conducted at the Dental Clinic of the Escuela Nacional de Estudios Superiores (ENES León), National Autonomous University of Mexico (UNAM), from May to December 2021. Primary caregivers of patients with CLP (n=70) were included as well as those of the patients without CLP (n=70) of the same institution. Sample size was calculated considering an OR=2.5, establishing a convenience selection. Caregivers answered the WHOQoL Bref instrument to assess QoL. Of the total sample analyzed, 88.6% of the caregivers were female (p>0.05). Caregivers of patients with CLP reported poor QoL (64.8%), compared to caregivers in the control group (p

The production of Moringa oleifera capsules has emerged as a promising agricultural activity in Mexico, driven by the plant’s well-documented health and nutritional benefits. In response, farmers have begun producing Moringa oleifera as a dietary supplement, using artisanal methods with minimal production controls. This study aimed to estimate the processing times of the Moringa oleifera production system using simulation modeling with Arena® software, and to evaluate the economic feasibility of capsule production. Methodologically, it was approached as a case study in the state of Veracruz, processing times were estimated through systematic sampling and modeled with Arena simulation software. Three simulation scenarios were considered to select a technically and economically viable alternative for agricultural producers: one with a 200-capsule encapsulator (1E200C), another with two 200-capsule encapsulators (2E200C) and a third with an 800-capsule encapsulator (1E800C). For the initial diagnosis a research stay was conducted for 180 days, and the production capacity was set at 24,000 capsules due to raw material limitations. Results indicated that the 1E800C scenario reduced processing time by 60% compared to the1E200C scenario, and by 35% compared to the 2E200C scenario. Additionally, the 1E800C model required only 2 days (16 hours) of work, while the 2E200C required 4 days (32 hours), and the 1E200C required 7 days (56 hours). In terms of production costs per unit of 90 capsules, the 1E200C was 3.93 USD the 2E200C 3.64 USD and the 1E800C 3.45 USD The study concluded that due to raw material limitations, the company can produce 12,800 units per year of 90 capsules. It is recommended to adopt the 1E800C encapsulator, which would lower overall production costs by 12.23%, representing 0.48 USD per unit produced, resulting in an additional profit of 6,150.50 USD Over a five-year evaluation period, the benefit-cost ratio was 5.03, the NPV was 922,370.11 and the IRR was 42.09%, indicating that this type of agribusiness in Mexico is both technically and economically feasible.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

The kinetics and efficacy profiles of photoinitiated polymerization are theoretically presented. For the same dose, lower light intensity achieves a higher steady-state-efficacy (SSE) in type-I; in contrast, type-II has an equal SSE. Higher light intensity has a faster rising efficacy, due to faster depletion of photoinitiator (PS) concentration. However, type-II process is also affected by the available oxygen. Higher light intensity produces more efficient singlet oxygen, resulting a higher transient efficacy, in which all intensities reach the same SSE when oxygen is completely depleted. With external oxygen, type-II efficacy increases with time, otherwise, it is governed only by the light dose, i.e., same dose achieves same efficacy. Moreover, type-II has an efficacy follows Bunsen Roscoe law (BRL), whereas type-I follows non-BRL. The measured type-I efficacy and gelation profile are analyzed by our analytic formulas. Schematics of the photocrosslinking stage defined by the availability of oxygen is developed, where both type-I and –II coexist until the oxygen is depleted. The overall efficacy may be enhanced by resupply of PS or oxygen during the light exposure. The roles of light dose and PS concentration on the efficacy of photoinitiated polymerization should be are governed a new concept of a volume efficacy (Ve), defined by the product of the crosslink (or gelation) depth (CD) and local [efficacy].

Optimal conditions for maximum efficacy of photoinitiated polymerization are theoretically presented. Analytic formulas are shown for the crosslink time, crosslink depth and efficacy function. The roles of photoinitiator (PI) concentration, diffusion depth and light intensity on the polymerization spatial and temporal profiles, for both uniform and non-uniform cases, are presented. For optimal efficacy, a strategy via controlled PI concentration is proposed, where re-supply of PI in high light intensity may achieve a combined-efficacy similar to low light intensity, but has a much faster procedure. A new criterion of efficacy based on the polymerization (crosslink) [strength] and [depth] is introduced. Experimental data are analyzed for the role of PI concentration and light intensity on the gelation time and efficacy.

The kinetics and modeling of dual-wavelength controlled photopolymerization confinement (PC) are presented and measured data are analyzed by analytic formulas and numerical data. The UV-light initiated inhibition effect is strongly monomer-dependent and different monomers have different C=C bond rate constants and conversion efficacy. Without the UV-light, for a given blue-light intensity, higher initiator concentration (C₁₀) and rate constant (k’) lead to higher conversion, as also predicted by analytic formulas, in which the total conversion rate (R_T) is an increasing function of k’R, which is proportional to k[gB₁C₁]^0.5. However, the coupling factor b₁ plays a different role that higher b₁ leads to higher conversion only in the transient regime; whereas higher b₁ leads lower steady-state conversion. For a fixed initiator concentration C₁₀, higher inhibitor concentration (C₂₀) leads to lower conversion due to stronger inhibition effect. However, same conversion reduction was found for the same H-factor of H₀ = [b₁C₁₀ - b₂C₂₀]. Conversion of blue-only are much higher than that of UV-only and UV-blue combined, in which high C₂₀ results a strong reduction of blue-only-conversion, such that the UV-light serves as the turn-off (trigger) mechanism for the purpose of spatial confirmation within the overlap area of UV and blue light. For example, UV-light controlled methacrylate conversion of a glycidyl dimethacrylate resin formulated with a tertiary amine co-initiator, and butyl nitrite, subject to a continuous exposure of a blue light, but an on-off exposure of a UV-light. Finally, we developed a theoretical new finding for the criterion of a good material/candidate governed by a double ratio of light-intensity and concentration, [I₂₀C₂₀.]/[I₁₀C₁₀].

We analyze the humoral and B-cell mediated immunogenic response induced by GP5 lineal epitopes from porcine reproductive and respiratory syndrome virus (PRRSV) to explore the role of this protein in the protective response. For inoculation, pigs aged twenty-one days were allocated into six groups (seven pigs per group): control (PBS), vehicle (carrier), vaccinated (Ingelvac-PRRSV, MLV®), non-vaccinated and naturally infected, GP5-B and GP5-B3. Subsequently blood samples were collected and analyzed. Cytokine were measured by ProcartaPlex kit. Peptide-specific IgGs and cross-reactivity against peptides were analyzed by ELISA and B-cell subpopulations were analyzed by flow cytometry. At 2 days post-immunization (dpi), the GP5-B3 peptide increased the serum concentrations of cytokines associated to activate adaptive cellular immunity (IL-1β and IL-12). The concentration of IgGs anti-GP5-B increased in both cases at 21 and 42 dpi, while IgGs anti-GP5-B3 increased at 21 dpi and remained at the same level until 42 dpi. Also, antibody-forming/Plasma B cells (CD2+/CD21-) and primed B cells (CD2-/CD21+) from immunized pigs showed an increase at 42 dpi. Conversely the naïve B cells from immunized pigs decreased compared with the controls. Importantly, Both GP5-B and GP5-B3 peptides exhibited immunoreactivity against serum antibodies from vaccinated group, as well as non-vaccinated and naturally infected group. In conclusion, GP5-B and GP5-B3 peptides elicited immunogenicity mediated by antigen specific IgG´s and B-cell activation.

This study was focused on the development of oil-producing microorganisms to generate lipids. The yeast Rhodotorula mucilaginosa (R. mucilaginosa) was selected for liquid-state cultivation, and the conditions for growth of the yeast cells were assessed. Additionally, the relationships between different nutrient elements and the growth of R. mucilaginosa were explored. The lipid accumulation of R. mucilaginosa is increased under nitrogen-restricted conditions. As the concentration of the carbon source increases, the accumulation of lipids is increased. However, if the carbon source concentration is further increased, the growth of yeast is inhibited. From a large-scale liquid fermentation culture with a fixed inoculation amount of 5%, and from a batch of culture experiments, it was determined that a suitable oil-producing culture was obtained on the 6th day, and the optimum conditions involved a carbon source concentration of 60 g/L, a nitrogen source concentration of 0.5 g/L, and a KH2PO4 concentration of 7.0 g/L. After utilizing different carbon sources in this study, it was found that glucose was the carbon source most conducive to the accumulation of R. mucilaginosa lipids. In addition, the extraction method and solvent for the extraction of R. mucilaginosa lipids were chosen. The acid-heat method using the green organic solvent ethyl acetate exhibited the best performance for extraction of yeast lipids under environmentally friendly and safe conditions. The analysis of lipids showed that the fatty acids obtained primarily contained C16:0, C18:1 and C18:2, and especially C18:1 (41%) lipids, indicating that R. mucilaginosa lipids are a good bio-oil source for the production of biodiesel.

Chronic noncommunicable diseases (NCDs) are responsible for approximately 74% of deaths globally. Medicinal plants have traditionally been used to treat NCDs, including diabetes, cancer, and rheumatic diseases, and are a source of anti-inflammatory compounds. This study aimed to evaluate the anti-inflammatory effects of Rhus trilobata (Rt) extracts and fractions in lipopolysaccharide (LPS)-induced inflammation models in vitro and in vivo. The aqueous extract (RtAE) and five fractions (F2 to F6) were obtained via C18 solid-phase separation and tested in murine LPS-induced J774.1 macrophages. Key inflammatory markers such as IL-1β, IL-6, TNF-α, and COX-2 gene expression were measured using RT-qPCR, and PGE2 production was assessed via HPLC-DAD. The in vivo effects were tested in an LPS-induced paw edema model in Wistar rats. Results showed that RtAE at 15 μg/mL significantly decreased IL-1β and IL-6 gene expression in vitro. Fraction F6 further reduced IL-1β, TNF-α, and IL-6 gene expression, COX-2 expression, and PGE2 production. In vivo, F6 significantly reduced LPS-induced paw edema, inflammatory infiltration, and IL-1β and COX-2 protein expression. These findings support the anti-inflammatory potential of RtAE and F6, reinforcing the medicinal use of Rt.

Severe malaria is a major public health concern in Angola, particularly among adults, with limited data on clinical outcomes and manifestations. The study therefore assessed the clinical manifestations and outcome of severe Plasmodium falciparum malaria in adult patients admitted to Hospital Central Dr. António Agostinho Neto of Lubango, Angola. The study retrospectively reviewed the individual records of patients over 14 years old, admitted for severe malaria during the first trimester of 2021 and 2022. World Health Organization (WHO) criteria were used to define severity. A total of 640 patients were recorded into the study, 167 in 2021 and 473 in 2022, distributed across the departments; Intensive Care Unit (ICU; n=81), Medicine (MED; n=458) and Infectiology (INF; n=101). The median age was 26 years and 59.4% were males. The most common manifestation of severe malaria was renal impairment (37.4%). The overall mortality rate was 7% and decreased considerably from 10.2% in 2021 to 5.9% in 2022. The increase in malaria cases during 2022 with increased in prevalence of life-threatening signs like renal impairment, jaundice and impaired conscience, underscores the urgent need for enhanced malaria control and surveillance strategies to mitigate morbidity and mortality, highlighting the potential for antimalarial drug resistance.

Cerebral Palsy (CP) poses substantial challenges to individuals, affecting their physical capabilities and daily functioning, and necessitates tailored interventions to enhance their quality of life and independence. Hand functionality is often affected in more than 60% of individuals with CP; they (mostly children) may spend up to 2-3 hours tightening their shoes perfectly. This includes the tightening of laces, standing up to determine if it is sufficient, and having to repeat the process many times till desired throughout the day. This paper focuses on the development of such a system that will assist them in effectively reducing this time to an approximate maximum time of 10 minutes. In its proposed form, this would reduce the shoe-tying process and make it ~18 times faster. The system will allow the user to perform the process with one hand and be simple and reliable. This additional freedom, among utilization of other systems, could lead to a betterment in mental health regarding the desire to perform outdoor activities among individuals with CP

We suggest a new solution to the strong CP problem. The solution is based on the proper use of the boundary conditions for the QCD generating functional integral. It obeys the principle of renormalizability of Quantum Field Theory and does not involve new particles like axions.

Recently, we published that the monoclonal antibody (D12 mAb) recognizes gp63 of L. mexicana, it is responsible for COX activity. This D12 mAb exhibited cross-reactivity with Trypanosoma cruzi, Entamoeba histolytica, Acanthamoeba castellanii, and Naegleria fowleri. COX activity assays performed in these parasites suggested the potential presence of such enzymatic activity. In our investigation, we confirmed that wild-type recombinant gp63 exhibits COX-like activity, in contrast to a mutated recombinant gp63 variant. Consequently, our objective was to identify sequences orthologous to gp63 and subsequently analyze the binding of arachidonic acid (AA) to the putative active sites of these proteins. Given the absence of a crystallized structure for this protein in the Protein Data Bank (PDB), it was imperative to first obtain a three-dimensional structure by homology modeling, using leishmanolysin (PDB ID: LML1) as a template in the Swiss model. Database. The results obtained through molecular docking simulations revealed the primary interactions of AA close to the Zinc atom present in the catalytic site of gp63-like molecules of several parasites, predominantly mediated by hydrogen bonds with HIS264, HIS268 and HIS334. Furthermore, COX activity was evaluated in commensal species such as E. dispar and during the encystment process of E. invadens.

An efficacious treatment of H. pylori infection is cornerstone for the global control of the diseases caused by this bacterium. Continuous epidemiologic surveillance of susceptibility of H. pylori to the antibiotics recommended for its eradication is highly recommended. This study aimed to determine the antimicrobial susceptibility pattern of 651 isolates from five different collections isolated between 1996 to 2008 in México City. The susceptibility profile of H. pylori isolates was determined by the E-test strips for each antibiotic (amoxicillin, clarithromycin, metronidazole, and tetracycline). Antimicrobial susceptibility testing showed a very high proportion of H pylori strains susceptible to amoxicillin, clarithromycin, and tetracycline (94.5%, 95%, and 99.5 %, respectively). In contrast, a high proportion (95%) of isolates was resistant to metronidazole. Notably, the proportion of susceptible/resistant strains to the 4 antibiotics over 5 consecutive time periods remained stable over time. Despite a wide use of amoxicillin and clarithromycin in the general population, the H pylori high susceptibility to these 2 antibiotics has been preserved during more than a decade. The high prevalence of resistance to metronidazole in H. pylori strains in our population compromises its use in the empirical treatment of H. pylori infection.

In recent years, cancer therapy has witnessed significant advancements, with a focus on personalized and targeted treatment strategies. One promising approach involves the use of stimuli-responsive biomaterials for site-specific drug release. Among these biomaterials, pH, and redox-triggered polymer-nano composites have gained immense attention due to their ability to respond to the specific tumor microenvironment, enhancing therapeutic efficacy while reducing off-target effects. Cancer cells often exhibit anomalous biochemical properties, attributed to lower cytosolic pH (acidic) and elevated redox potential through the epitomized upregulation of undesired genes. Such biological process substantially imbalance the level ions (protons) and biological thiols glutathione (GHS) in the cytoplasm as well as in the subcellular organelles. Superfluous accumulation of ions and redox imbalance is associated with proliferation, invasion, and growth of tumor. Because of high surface area, deep tissue penetration capability, higher hydrophilicity, hydrophobic interior for drug/gene efficient loading, biocompatibility and site-specific targeting efficiency, functionalized polymer nanocomposites are superior to conventional small molecular materials. Paradoxically conventional methods of drug delivery aided therapeutics accompanied with inherent drug/genes are encapsulated in biocompatible carrier or suitable transfecting agents generally suffered with low bioavailability, uncontrolled drug release, low cellular penetration, cellular internalization, toxicity, and poor drug loading efficiency. To overcome these issues, recently various multifunctional nanomaterials were developed, based on synergistic stimuli responsive aided drug release in a specified cellular or subcellular system. High therapeutic efficacy, of nanoparticles (NPs) mainly associated with surface functionalization through biocompatible polymeric materials, site-specific targeting units accompanied with stimuli responsive components. Followed by therapeutically important drug or genetic materials were loaded into NPs either in covalent or non-covalent approach. Intriguingly, combined pH and redox dual stimuli based functional materials specially based on polymeric nanocomposites for cancer therapeutics scarcely reported. This article provides the recent progress in pH and redox-responsive polymer-nano composites for site-specific drug delivery in cancer therapy. It explores design principles, fabrication methods, mechanism of action, and prospects of these dual-stimuli responsive biomaterials.

Detailed kinetics for a 3-wavelength photopolymerization confinement (PC) system is presented for both numerical solutions and analytic formulas. The dynamic profiles are simulated for oxygen, free radical, and conversion for various situations of: blue-light only, 2-light (red and UV), and 3-light (red, blue, UV). An effective PC requires two conditions: (i) a strong N-inhibition for uncured regime with a low conversion (triggered by the UV-light); and (ii) a weak S-inhibition (oxygen-induced) for high conversion under the blue-light or blue and red-light initiation. Good PC candidates are governed by collective factors of: (i) the double ratio of light-intensity and initiator-concentration, (ii) monomers rate-constant; and (iii) effective absorption constants at specific wavelength and initiators. A new reverse feature for the role of N-inhibition on the blue-conversion is found. Higher oxygen concentration leads to a lower conversion, which could be enhanced by reducing the S-inhibition via a red or blue-light pre-irradiation, having a pre-irradiation time TP=200 s for red-light only, and reduced to 150 s, when both red and blue-light. System under UV-only leads a conversion lower than that of blue-only. However, conversion could be improved by the dual-light (blue and UV), and further enhanced by the pre-irradiation of red-light. The two competing factors, N-inhibition and S-inhibition, could be independently and selectively tailored to achieve: (a) high conversion of blue-light (without UV-light), enhanced by red-light pre-irradiation for minimal S-inhibition; and (b) efficient PC initiated by UV-light produced N-inhibition for reduced confinement thickness and for high print speed.

Opuntia ficus-indica has always interacted with many phytophagous insects at its center of origin; two of them are Dactylopius coccus and D. opuntiae. D. coccus, or true cochineal, is produced to extract carminic acid, and D. opuntiae or wild cochineal is a key invasive pest of O. ficus-indica in more than 20 countries around the world. Despite the economic and environmental relevance of this cactus and, D. opuntiae and D. coccus, there are few studies that have explored volatile organic compounds (VOCs) derived from the plant-insect interaction. The aim of this work was to determine VOCs of D. coccus and D. opuntiae feeding on cultivars suitable for their development and to identify different VOCs in cladodes infested by each Dactylopius species. Volatiles were identified through their essential oils, which were obtained by hydrodistillation. A total of 66 VOCs from both Dactylopius species were identified, and 125 from the Esmeralda and Rojo Pelón cultivars infested by D. coccus and D. opuntiae, respectively, were determined. Differential VOCs production due to infestation by each Dactylopius species was also found. Some changes in methyl salicylate, terpenes such as linalool or the alcohol p-vinylguaiacol were related to Dactylopius feeding on cladodes of their respective cultivars. Changes in these VOCs and their probable role in plant defense mechanisms should receive more attention because this knowledge could improve D. coccus rearing, or to its inclusion in breeding programs for D. opuntiae control in regions where it is a key pest of O. ficus-indica.

As precision medicine such as targeted therapy and immunotherapy often have limited accessibility, low response rate and evolved resistance, it is urgent to develop simple, low-cost, and quick-turnaround personalized diagnostic technologies for drug response prediction with high sensitivity, speed, and accuracy. Major challenges of drug response prediction strategies employing digital database modeling are the scarcity of labeled clinical data, applicable only to a few classes of drugs, and losing the resolution at the individual patient level. Although these challenges have been partially addressed by large-scale cancer cell line datasets and more patient-relevant cell-based systems, the integration of different data types and data translation from pre-clinical to clinical utilities are still far-fetched. To overcome current limitations of precision medicine with a clinically proven drug response prediction assay, we have developed an innovative and proprietary technology based on in vitro patient testing and in silico data analytics. First, a patient-derived gene expression signature was established via transcriptomic profiling of cell-free mRNA (cfmRNA) from the patient’s blood. Second, a gene-to-drug data fusion and overlaying mechanism to transfer data was performed. Finally, a semi-supervised method was used for database searching, matching, annotation and ranking of drug efficacies from a pool of ~700 approved, investigational or clinical trial drug candidates. A personalized drug response report can be delivered to inform clinical decision within a week. The PGA (Patient-derived Gene expression-informed Anticancer drug efficacy) test has significantly improved patient outcomes when compared to the treatment plans without PGA support. Implementation of PGA, which combines patient-unique cfmRNA fingerprints with drug mapping power, has the potential to identify treatment options when patients are no longer responding to therapy and when standard-of-care is exhausted.

Titanium-based metal-matrix composites manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing high reinforcement content remains challenging. This study reports an improved manufacturing process for Ti-TiC enabling high reinforcement content and significant fracture strain concurrently: mechanical blending, followed by laser powder bed fusion and a single heat treatment. As-built microstructure shows both un-melted TiC particles and sub-stoichiometric TiC dendrites resulting from a partial dissolution of TiC particles. The heat treatment is shown to fully convert TiC dendrites into equiaxed TiC grains. Reduction of the C/Ti ratio in TiC during the process results in an increase in the reinforcement content, from a nominal 12 vol% to an effective 21.5 vol%. Ti-TiC tensile samples reached fracture strains of up to 1.7%, Young’s moduli of up to 149 GPa and ultimate tensile strengths of up to 827 MPa. Lower TiC initial powder size distributions displayed the best mechanical performance.

The individual and combined effects of extracellular products (ECP) from Arthrobotrys oligospora (Ao) and A. musiformis (Am) growth in liquid media against Haemonchus contortus L3 (HcL3) were assessed. The following methodological steps were established: isolation, morphological (MI) and molecular identification (Mol-I), assessment of nematocidal activity (NA) of fungal liq-uid culture filtrates (LCF) produced in two liquid media alone and in combination and finally, the myco-compound profile identification (MCP). The MI of both isolates suggested that the fungi corresponded to the species Ao and Am. This result was confirmed by PCR analysis followed by sequencing, alignment and obtaining coverage and similarity with respect to isolates reported in the NCBI database. Likewise, the highest Hc mortalities were 91.4% with individual LCF of Am and 86.2% with those of Ao at the highest concentration (100 mg/mL) in Czapek-Dox Broth. The combination of both LCF resulted in a similarly high larval mortality with no statistical differ-ences in relation to individual activity (P>0.05). The MCP showed the presence of alkaloids in both fungi. Coumarins, triterpenes and saponins were found only in Ao. Both fungi produced ECP with a high NA that could be identified and assessed in future studies as potential natural an-thelmintic compounds.

Understanding the distribution of rock glaciers provides key information for investigating and recognizing the status and changes of the periglacial environment. Deep learning algorithms and red-green-blue (RGB) bands from high-resolution satellite images have been extensively employed to map rock glaciers. However, the near-infrared (NIR) band offers rich spectral information and sharp edge features that could significantly contribute to semantic segmentation tasks, but it is rarely utilized in constructing rock glacier identification models due to the limitation of three input bands for classical semantic segmentation networks, like DeeplabV3+. In this study, a dual-encoder DeeplabV3+ network (DEDNet) was designed to overcome the flaws of classical DeeplabV3+ network (CDNet) when identifying rock glaciers using multispectral remote sensing images by extracting spatial and spectral features from RGB and NIR bands, respectively. This network, trained with manually labeled rock glacier samples from QiLian Mountains, established a model with accuracy, precision, recall, specificity, and mIoU (Mean Intersection over Union) of 0.9131, 0.9130, 0.9270, 0.9195, and 0.8601, respectively. The well-trained model was applied to identify new rock glaciers in a test region, achieving a producer's accuracy of 93.68% and a user's accuracy of 94.18%. Furthermore, the model was employed to two study areas in northern Tien Shan (Kazakhstan) and Daxue Shan (Hengduan Shan, China) with high accuracy, which proved that the DEDNet offers an innovative solution to more accurately map rock glaciers on a larger scale due to its robustness across diverse geographic regions.

This research investigates the impact of Al and Ti elements on the formation of self-generated ordered phase in high-entropy alloys (HEA), which have been receiving widespread concentration in present times thanks to their remarkable multifunctional properties and wide range of component selection. By adjusting the dual elements of Al and Ti, the study explores the regulation of quantity and distribution of the in-situ self-generated ordered phases in the alloy. The results of the annealing heat treatment process demonstrated that, through accession Al and Ti elements, the Cr-Fe-Ni medium-entropy alloy transfer from BCC phase to BCC+FCC phase and the precipitation of new phases such as B2, L21, and σ. This led to a synergistic impact of second phase strengthening, and also of solid solution strengthening, resulting in improved compressive properties of HEA.

Directed energy deposition (DED) parameters were determined for near-β alloy Ti-55511 by employing statistical design of experiments (DOE) methods. Parameters resulting in fully dense freeform deposits were identified using two sequential DOEs. Single laser tracks were printed with several laser power, traverse rate, and powder feed rate settings in an initial DOE to identify promising build parameters. Capture efficiency and effective deposition rate were used to characterize and rank the single track deposits. The best parameters were then used to print solid cube with various X-Y and Z-overlaps (different hatch spacing, HS, and layer thickness, ZS) in a second DOE. Suitable deposition parameters were selected based on cube density and microstructure and were used to fabricate larger tensile samples for mechanical testing. Multiple parameter sets were found to provide dense Ti-55511 deposits with acceptable mechanical properties and parametric models showed statistical significance.

Reduced glutathione (GSH) is an antioxidant in plants and is one of the important ways for plants to combat low-temperature stress. In this paper, Eriobotrya japonica Lindl. cv. Zaozhong No. 6 seedlings were used to study the effects of exogenous 5-aminolevulinic acid (ALA) application on glutathione synthesis and cyclic metabolism of loquat seedlings under low-temperature stress and to explore the regulatory mechanism of ALA on loquat cold tolerance. The results showed that ALA treatment could increase the content of GSH and the reduced glutathione/oxidized glutathione (GSH/GSSG) ratio in loquat leaf slices under low-temperature stress; reduce the electrolyte leakage rate and GSSG, H₂O₂ and MDA contents in leaf tissues; and alleviate the peroxidation damage caused by low temperature. ALA treatment increased the activity of γ-glutamine synthetase (γ-ECS) in loquat leaf slices under low-temperature stress and promoted the biosynthesis of reduced glutathione, thereby increasing the GSH content in leaf tissues. On the other hand, ALA treatment could also improve the activities of glutathione reductase (GR), glutathione S-transferase (GST) and glutathione peroxidase (GPX) and promote the cyclic regeneration of GSH, accordingly maintaining a high GSH/GSSG ratio, promoting the removal of reactive oxygen species (ROS), and enhancing the antioxidant capacity of leaves. The regulatory effect of ALA on enhancing the antioxidant capacity of loquat seedlings under low-temperature stress can be inhibited by L-buthionine-sulfoximine (BSO, GSH biosynthesis inhibitor). The results showed that ALA improved the antioxidant capacity of loquat seedlings under low-temperature stress, and GSH was involved in the regulation of the antioxidant effect of ALA on loquat seedlings under low-temperature stress.

700 MPa grade Ti and Nb-Ti microalloyed steels produced by thermo-mechanical control rolled processes (TMCP) were studied to elucidate texture that contributes to delamination and consequent impact toughness. The microstructure of Ti and Nb-Ti steels consisted of ferrite and bainite. Compared with Ti steel, Nb-Ti steel was characterized by a microstructure with finer ferrite and more bainite. The results from tensile and impact tests indicated that there is insignificant change in tensile properties, but toughness was greater in Nb-Ti steel compared with Ti steel. More severe delamination in Nb-Ti steel is attributed to stronger α-fiber (RD ||<110>) texture than Ti steel, especially {100}<110>, {113}<110> and {112}<110> texture. Typical cleavage river patterns were not observed on delaminated fracture surface, instead the cleavage fracture surface indicated some dimples. Interestingly, the impact energy of samples with delamination was greater than samples without delamination in the ductile–brittle transition region. The study suggests that delamination in the ductile–brittle transition zone may also be representative of high toughness.

Wildlife monitoring can be time-consuming and expensive, but the fast-developing technologies of uncrewed aerial vehicles, sensors, and machine learning pave the way for automated monitoring. In this study we trained YOLOv5 neural networks to detect Points of Interest, hare (Lepus europaeus), and roe deer (Capreolus capreolus) in thermal aerial footage and proposed a method to manually assess the parameter mean average precision (mAP), compared to the number of actual false positive and false negative detections in a subsample. This showed that a mAP close to 1 for a trained model does not necessarily mean perfect detection and provided a method to gain insights into the parameters affecting the trained models' precision. Furthermore, we provided a basic, conceptual algorithm for implementing real-time object detection in uncrewed aircraft systems equipped with thermal sensors, with high zoom capabilities, and a laser rangefinder. Real-time object detection is becoming an invaluable complementary tool for the monitoring of cryptic and nocturnal animals with the use of thermal sensors.

Drug repositioning is an efficient strategy to search for new treatment alternatives that is especially valuable for neglected parasitic diseases such as leishmaniasis. Tamoxifen and raloxifene are selective estrogen receptor modulators (SERM) that have shown antileishmanial activity. Clomiphene is a SERM structurally similar to tamoxifen whose antileishmanial potential is unknown. That is why the objective of the present work was to evaluate its antileishmanial activity in vitro and in vivo, in comparison with tamoxifen. The inhibitory effect against promastigotes of L. amazonensis, L. major and L. mexicana was evaluated for both compounds; as well as the cytotoxicity against mouse peritoneal macrophages, the growth inhibitory activity in intracellular amastigotes of L. mexicana, and the in vivo activity in mice experimentally infected with L. mexicana. Clomiphene was about twice as active as tamoxifen against both promastigotes and intracellular amastigotes, with IC50 values of 1.7-3.3 µM for clomiphene and 2.9-6.4 µM for tamoxifen against all three species promastigotes; and 2.8 ± 0.2 µM and 3.7 ± 0.3 µM, respectively, against L. mexicana amastigotes. Clomiphene structurally affected several parasite organelles in a concentration-dependent fashion, leading to the death of both promastigotes and intracellular amastigotes. Interestingly, the macrophage host cell did not appear damaged with any of the clomiphene concentrations tested. By oral administration at 20 mg/kg for 14 days, both compounds showed similar effects in terms of reducing the growth of the lesions, as well as the weight of the lesions and the parasite load at the end of the follow-up period. The results showed the potential of SERM as antileishmanial drugs and support further testing of clomiphene and other compounds of this pharmacological group.

A Q-switched Nd:YAG laser was focused on Pb-Ti alloy samples in several Laser Induced Breakdown experiments in order to measure the Stark parameters of several spectral lines (58) of single ionized Titanium including the 3504.89 Å, and the 3510.83 Ålines (where we aported new experimental and theoretical values).Diagnostics of the laser induced plasmas (electron density and electron temperature) was performed using Balmer’s H alpha line (6562.7 Å).Temperatures were obtained by the Boltzmann Plot technique with spectral lines of Pb I (after correction for its evident self-absorption).Subsequently, calculations by the Griem approach of the Stark broadening parameters for several spectral lines were performed using the Gaunt factors proposed by Van Regemorter and those proposed by Douglas H. Sampson. In the latter cases the values obtained were very close to the experimental values. It allows us to assume that the calculations made for the spectral lines of Ti II, without experimental information, are more accurate using the Gaunt factors proposed by Sampson.

Some wind farms have implemented automated camera\textendash based monitoring systems e.g. IdentiFlight to mitigate the impact of wind turbines on protected raptors. These systems have effectuated the collection of large amounts of data that can be used to describe flight behavior in a novel way. This data uniquely provides both flight trajectories and images of individual birds throughout their flight trajectories. The aim of this study was to evaluate how this unique data could be used to create a robust quantitative behavioral analysis, that could be used to identify risk prone flight behavior and avoidance behavior thereby in the future assess collision risk. This was attained through a case study at a wind farm on the Swedish island Gotland, where golden eagles (Aquila chrysaetos), white-tailed eagles (Haliaeetus albicilla), and red kites (Milvus milvus), were chosen as the selected bird species. The results demonstrate that flight trajectories and bird images can be used to identify high risk flight behavior and thereby also used to evaluate collision risk and avoidance behavior. This study presents a promising framework for future research, demonstrating how data from camera\textendash based monitoring systems can be utilized to quantitatively describe risk prone behavior and thereby assess collision risk and avoidance behavior.

This study outlines a 3-step production process for Ti-TiC Metal Matrix Composite (MMC) employing powder Mechanical Blending, Laser Powder Bed Fusion (LPBF), and a heat treatment. A TiC fraction of more than 20 vol% was formed in-situ through the reaction of titanium with carbon during the LPBF process. The manufactured MMC pieces showed a record stiffness and fracture strain combination. The LPBF energy density impacted strongly porosity type. The as-built microstructure displayed an homogeneous distribution of sub-stoichiometric TiC dendrites which were fully converted into equiaxed TiC grains during the heat treatment. The TiC C/Ti ratio was found to be close to 0.5, resulting in an effective reinforcement content nearly twice the one expected for stoichiometric TiC, leading to stronger reinforcement. The mechanical analysis revealed a Young’s modulus of up to 149 GPa and an ultimate tensile strength of up to 770 MPa, indicating a 27% and 34% improvement, respectively, compared to commercially pure Titanium produced by LPBF and heat treated in the same conditions. A fracture strain of up to 2.8% was achieved. The combination of in-situ formation of defect-free TiC reinforcement and subsequent heat treatment enables to reach an exceptional ductility, considering the 20 vol% reinforcement content.

Petrochemicals, which convert oil and gas into products such as plastics, are fundamental to modern societies. Chemists recognize their role in the design of materials and the adverse effects that these may have on the environment, preventing sustainable development. Several methodological frameworks and sustainability assessment approaches have been developed to evaluate the resources used in the petrochemical sector in terms of environmental costs. A combination of Life Cycle Assessment and Emergy Accounting - to assess the environmental support for resource use - is applied in this study of the PET production chain in Europe. The Unit Emergy Values of several intermediates are calculated or updated to facilitate discernment of the quality of energy used and the processes' efficiency. Several routes for synthesizing renewable para-xylene and ethylene glycol from biomass are discussed and confronted with the efforts focused on recycling and recovering the final product providing concurrently a procedure and a valuable data set for future CP actions. The results show that understanding the efficiencies changing across the production chain may help stakeholders make wise choices as to where and when interventions to promote a circular economy are most effective along a petrochemical production chain.

Sandblasting materials used for dental restoration is a valuable preconditioning technique enhancing the physical properties and promotes osseointegration and cell adhesion. Ti medical grade 4 and Ti6Al4V were blasted with a series of various naturally occurring and synthetically produced spraying materials of controlled granulometry, at precise spraying duration and spraying pressure, and the results were analyzed in terms of the obtained surface roughness and by SEM analysis. It was found that in all cases, regardless of the spraying material or working conditions, the roughness profile achieved is a uniformly distributed one. A reduction in the blasting pressure by half led to a decrease in the roughness between 30 and 35%. The use of glass balls as blasting material led to decreased roughness and a more uniformly distributed roughness values for Ti as well as for Ti6Al4V regardless of spraying duration or applied pressure comparing to other spraying materials, and blasting with olivine led to increased, as well as uniformly distributed values, and hence the conclusion that one may control the roughness size by choosing one or another from the above materials, without the need of changing any other operating parameters. In the case of Ti, the achieved roughness is greater than in the case of Ti4Al6V, irrelevant of the blasting material, the differences being smaller the softer the sandblasting material due to the fact that Ti alloys have better mechanical properties and increased hardness comparing to pure Ti. SEM analysis showed that the use of sintered hydroxyapatite as an additive to the blasting material does not necessarily lead to a substantial deposition of hydroxyapatite on the substrate materials, only traces of it being identified during the analysis.

The effects of the dielectric constant of the powder phase on lead zirconate titanate (PZT)/PZT sol-gel composite films were investigated to tailor their electrical properties. Three types of PZT powders were used to fabricate three different PZT/PZT sol-gel composite films. The PZT powders had the same electromechanical coupling coefficient but different relative dielectric constants. The PZT/PZT films were fabricated on a 3 mm-thick titanium substrate using an automatic spray coating system, and their properties were investigated. The relative dielectric constants of the PZT/PZT films were successfully controlled by tailoring the properties of the PZT powder phase. However, the piezoelectric constants showed a tendency different to those of the raw powders, because of the poor poling degree. This was overcome by conducting poling at a high temperature.

This study investigates the possibility of using machine learning models created in DeepLabCut and Create ML to automate aspects of behavioral coding and aid in behavioral analysis. Two models with different capabilities and complexities were constructed and compared to a manually observed control period. The accuracy of the models was assessed before being applied to 7 nights of footage of the nocturnal behavior of two African elephants (Loxodonta africana). The resulting data was used to draw conclusions regarding behavioral differences between the two elephants and between individually observed nights, thus proving that such models can aid researchers in be-havioral analysis. The models were capable of tracking simple behaviors with high accuracy, but had certain limitations regarding detection of complex behaviors, such as the stereotyped behavior sway, and displayed confusion when deciding between visually similar behaviors. Further expansion of such models may be desired to create a more capable aid with the possibility of automating behavioral coding.

The integration of modern technologies like intramedullary fixators and advanced biometallic alloys has revolutionized traumatology and orthopedics. While these innovations have improved treatment, the exploration of new materials for implants persists. Tantalum and niobium, both non-toxic with similar properties, are preferred for titanium-based biomedical alloys due to their exceptional biocompatibility and corrosion resistance. Acting as stabilizers in titanium alloys, they form passive oxide layers resisting corrosion and remain compatible with biological systems. The novel Ti21Nb6Ta (TNT) alloy promises enhanced osteosynthesis outcomes. Our in vivo research on experimental animals evaluated the biocompatibility and osteoinduction of TNT compared to Ti-6Al-4V (BT-6) alloy (control group). The study comprised three experiments across different animal species, assessing acute toxicity, irritant effects, and long-term biocompatibility and osteoinduction through simulated osteosynthesis. Results indicated that aqueous extracts from both alloys were non-toxic and non-irritating. Furthermore, both demonstrated high biocompatibility and active osteoinduction potential after three months of implantation.

Peptidyl-prolyl cis/trans isomerases (PPIases) are present in a wide variety of microorganisms, including protozoan parasites such as Trypanosoma cruzi, Trypanosoma brucei, Trichomonas vaginalis, Leishmania major, Leishmania donovani, Plasmodium falciparum, Plasmodium vivax, Entamoeba histolytica, and Giardia intestinalis, all of which cause important neglected diseases. PPIases are classified as cyclophilins, FKBPs, or parvulins and play crucial roles in catalyzing the cis-trans isomerization of the peptide bond preceding a proline residue. This activity assists in correct protein folding. However, the biological structure‒function characterization of PPIases from these protozoan parasites is still incomplete. The recombinant production of these enzymes is highly relevant for this ongoing research. In this review, we explore the structural diversity, functions, recombinant production, and activity and inhibition of protozoan PPIases. We also highlight their potential as biotechnological tools for the in vitro refolding of other recombinant proteins from these parasites. These applications are invaluable for the development of diagnostic and therapeutic tools.

In this study, TiO2 nanostructured coatings on Ti-6A-4V alloys were fabricated by two methods: H2O2 oxidation and RF sputtering. In the annealing temperature range of 25 C - 500 C, there were the peaks at 35, 37, 40 and 52 corresponding to {100}, {002}, {101} and {102} crystal planes of hcp structure of α-Ti. At the annealing temperature of 600 C, there was the presence of peaks corresponding to crystal planes of anatase and rutile TiO2. The relative intensities of anatase and rutile phases of the sample fabricated by RF sputtering were 3.62 and 10.25 %, respectively; while those of the sample fabricated by H2O2 oxidation were 21.27 and 3.20 %, respectively (The relative intensity of α-Ti phase was 100 %). The results investigated the peak shift of α-Ti phase in TiO2/Ti-6Al-4V nanostructured coatings fabricated by the two methods which was reasonably explained from the difference in the thermal expansion coefficients of Ti alloy and TiO2 components, as well as the difference in the ratio of anatase to rutile phases.

We consider spontaneous quark transitions between the Λ0 baryon and its resonant states, and (anti)quark transitions between the neutral kaon K0 and the two heavy ηq-mesons (q = c, b). We use the measured differences in mass deficits to calculate the binding energy levels of valence c and b (anti)quarks in these transitions. In the process, we account for isospin energy release in K0 transitions and for the work done by the strong force in suppressing Coulomb repulsions in the charged Λc+-baryon. We find that the flips s→c and s¯→c¯ both release energy back to the strong field; and that the overall range of quark energy levels above their u-ground is 100-MeV wider than that of antiquark energy levels above their d¯-ground. The wider quark range stems from the flip s→b, which costs 283 MeV more (or 3× more) than the corresponding antiquark flip s¯→b¯. At the same time, transitions from the respective ground states to the s and s¯ states (or the c and c¯ states) point to a clear origin of the elusive charge-parity (CP) violation. The determined binding energy levels of (anti)quarks allow us to analyze in depth the (anti)quark transitions in Λ-baryons and B-mesons.

Installation of offshore wind farms is rising, driven by the goal of changing the global energy matrix. However, many of its possible impacts are still unknown. Increased noise levels, disruptions to food chains, pollution due to traffic, and impacts on fishing communities and tourism are all potential effects to consider. Marine habitats are essential carbon dioxide sinks. Therefore, losing marine biodiversity due to offshore wind farms can be counterproductive in mitigating climate change. Balancing biodiversity conservation, wind potential, and political interests is challenging. Today, Uruguay has practically decarbonized its electrical matrix, incorporating wind, solar, and biomass energy alongside hydroelectricity. In line with this, the country's Hydrogen Roadmap highlights green hydrogen as relevant, potentially serving as a transportation fuel for both domestic consumption and export. Combining the country's strong base of wind experience with its sustainable policy, it plans to implement offshore wind farms to produce green hydrogen, making studies of its impacts crucial. This paper reviews the current social and environmental information on the Uruguayan coastal habitat, analyzes onshore wind farms' ecological studies, and examines offshore wind farms' global environmental and social impacts. Finally, it proposes suggested studies for environmental approval for offshore wind farms.

This study examines the complex relation among environmental taxes, productive capacities, urbanization, and their collective effects on environmental quality in Africa, drawing on two decades of data from twenty African countries. It situates the study within the broader discourse on sustainable development and economic growth, emphasizing the Environmental Kuznets Curve (EKC) framework to examine the relationship between economic development, characterized by urban expansion and increased productive capacities, and the adoption of environmental taxes amidst the continent’s diverse economic and environmental environments. Using advanced econometric techniques, including the Cross-Section Augmented Autoregressive Distributed Lag (CS-ARDL) model and the Dynamic Common Correlated Effects Mean Group (DCCEMG) estimator, the study addresses data challenges such as cross-sectional dependence and slope heterogeneity. The results provide important insights into the dynamics of environmental quality in relation to economic and urban growth and the role of environmental taxation. The study proposes tailored policy strategies aimed at strengthening sustainable development initiatives in line with international agreements such as the Paris Agreement and the Sustainable Development Goals. These strategies advocate for a nuanced application of environmental taxes and the promotion of productive capacities to enhance environmental sustainability across the African continent.

Stable half-sandwich iron(II) dihalido complexes of the type [Fe(5-Cp’)X2] are extremely scarce, being limited to congeners containing the bulky C5H2-1,2,4-tBu3 ligand. We have extended this to homologues [Fe(5-Cp*)X2] (X = Cl – I) containing the particularly popular C5Me5 (Cp*) ligand. Corresponding ionic compounds ER4[Fe(5-Cp*)X2] are easily accessible from FeX2, MCp* (M = Li, K) and a suitable halide source R4EX (E = N, P) in THF. The new compounds NnPr4[Fe(5-Cp*)X2] (X = Cl, Br), NnPr4[Fe(5-Cp*)BrCl] and PPh4[Fe(5-Cp*)X2] (X = Cl, Br, I) have been structurally characterised by single-crystal X-ray diffraction. NnPr4[Fe(5-Cp*)Cl2] reacts readily with CO to afford [Fe(5-Cp*)Cl(CO)2], indicating the synthetic potential of ER4[Fe(5-Cp*)X2] in FeCp* half-sandwich chemistry.

The conformations of trifluoroacetyl triflate, CF3C(O)OSO2CF3, were investigated through vibrational experimental methods (gas-phase FTIR, liquid-phase Raman, and Ar-matrix FTIR spectroscopy) and Density Functional Theory (DFT) calculations. A potential energy surface was computed using the B3P86 /6-31+g(d) approximation as a function of the dihedral angles τ1 = CCOS and τ2 = COSC. The surface reveals three minima, which were further optimized using the B3LYP method with various basis sets (6-31++G(d), 6-311++G(d), tzvp and cc-pvtz). The global minimum corresponds to a syn-anti conformer (the CO double bound syn with respect the O−S single bond and the C−O single bond anti with respect to de S−C single bond). The other two minima represent enantiomeric syn-gauche forms. The Ar-matrix FTIR spectrum exhibited clear evidence of the presence of two conformers. Furthermore, the randomization process observed following broad-band UV-visible irradiation facilitated the identification of the IR absorption of each conformer. Based on the Ar-matrix FTIR experiments, the vapour phase of trifluoroacetyl triflate at room temperatures was composed of approximately 60-70% of the syn-anti conformer and 30-40% of the syn-gauche form.

Background Coronary artery disease (CAD) is a widely recognized cardiovascular disease that is considered the leading cause of death worldwide, affecting people on a global scale. Percutaneous coronary intervention (PCI), which involves procedures such as balloon angioplasty or stenting, plays an important role in opening blocked arteries and minimizing damage to the cardiac muscle. While the use of drug-eluting stents (DESs) has significantly reduced the occurrence of coronary restenosis, the problem of in-stent restenosis (ISR) continues to pose a significant clinical challenge. Gaining a deeper understanding of the clinical predictors associated with ISR is vital for early detection and appropriate treatment. Hence, this study aimed to evaluate the clinical predictors of ISR specifically in Taiwanese patients. Methods We conducted a single-center, retrospective case-control study, enrolling 517 CAD patients undergoing previous coronary stenting and stable angina with positive stress test or acute coronary syndrome (ACS) during follow-up between January 2019 and December 2022 at National Taiwan University Hospital. The patients were categorized into two groups: the ISR group, consisting of individuals who received drug-coated balloon (DCB) treatment (n=177), and the non-ISR group, comprising patients who did not receive DCB treatment (n=340). To gather relevant data, we meticulously reviewed the medical records and analyzed the findings from coronary angiography to assess the clinical characteristics of the patients. Results Patients with three-vessel disease (3VD) exhibited a higher prevalence of underlying diseases and were more likely to be taking aspirin and clopidogrel. Moreover, our analysis revealed that age (adjusted odds ratio [aOR] 1.02, 95% confidence interval [CI] 1.00 - 1.04, p = 0.037) and the presence of 3VD (adjusted odds ratio [aOR] 2.15, 95% confidence interval [CI] 1.03 - 4.46, p = 0.039) were significantly associated with an increased risk of coronary ISR. Conclusions Older age and 3VD were the independent predictors of coronary ISR in CAD patients receiving coronary stent implantation.

The effect of defects and microstructure on mechanical properties of Ti-6Al-4V welds produced by tungsten inert gas welding, plasma arc welding, electron beam welding and laser beam welding was studied in the present work. The mechanical properties of the different weld types have been evaluated with respect to micro hardness, yield strength, ultimate tensile strength, ductility and fatigue at room temperature and at elevated temperature. Metallographic investigation was carried out to characterize the microstructures of different weld types and fractographic investigation to relate the effect of defects on fatigue performance. Electron and laser beam welding produced welds with finer microstructure, higher tensile ductility and better fatigue performance than tungsten inert gas welding and plasma arc welding. Large pores and pores located close to the specimen surface were found to be most detrimental to fatigue life.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

Magneto-optic surface plasmon resonance (MOSPR) based sensors are highly attractive as next generation biosensors. However, these sensors suffer from oxidation leading to degradation of performance, reproducibility of the sensor surface because of the difficulty of removing adsorbed materials, and degradation of sensor surface during surface cleaning, and these limit their applications. In this paper, I propose MOSPR-based biosensors with 0 to 15 nm thick inert polycarbonate laminate plastic as a protective layer and theoretically demonstrate the practicability of our approach in water-medium for three different probing samples: ethanol, propanol, and pentanol. I also investigate microstructure and magnetic properties. The chemical composition and layered information of the sensor are investigated using X-ray reflectivity and X-ray diffraction analyses and these show distinct fcc-Au (111) phases, as dominated by the higher density of conduction electrons in Au as compared to Co. The magnetic characterization measured with the in-plane magnetic field to the sensor surface for both the as-deposited and annealed multilayers showed isotropic easy axis magnetization parallel to the multilayer interface at a saturating magnetic field of <100 Oe. The sensor showed a maximum sensitivity of 5.5 × 10⁴%/RIU for water-ethanol media and the highest detection level of 2.5 × 10⁻⁸ for water-pentanol media as the protective layer is increased from 0 to 15 nm.c

This work deals with the analysis of phase composition of sintered Ti-Al-C composite materials under high voltage electrical discharge. The samples of Ti-Al-C powder composites were tested by SEM, Raman spectroscopy and XRD. It was determined that the treatment of the powder by high voltage electrical discharge (HVED) and further sintering at high temperatures using the method of spark plasma sintering (SPS) encourages the formation of the intermetallic reinforcing phases, carbides and different nanocarbon structures like graphene and fullerenes, as well as pure graphite. Intermetallic phases and nanocarbon structures improve mechanical and physical properties of the composites. By using experimental methods mentioned above, the phase composition of Ti-Al-C powder composites obtained at different sintering temperatures was determined.

The effect of prostaglandin E1 (PGE1) encapsulated in nanoparticles (Nano PGE1) on motor dysfunction and muscle atrophy induced by sciatic nerve injury (SNI) was investigated in rats, and was compared with PGE1 encapsulated in lipid microspheres (Lipo PGE1) or PGE1 clathrated in cyclodextrin (PGE1-CD). The hind limb muscle weight ratio decreased until 2 weeks after SNI. All 3 PGE1 formulations significantly improved SNI-induced motor dysfunction. Nano PGE1 significantly promoted recovery from muscle atrophy at 2 and 3 weeks after SNI. Lipo PGE1 was also effective, but multiple doses were required. Compared with the SNI control group, the Nano PGE1 group showed upregulation of vascular endothelial growth factor (VEGF) and agrin expression in the injured sciatic nerve and atrophic muscles. Nano PGE1 accumulated prominently at the site of nerve injury and persisted for longer than Lipo PGE1 or PGE1-CD. Expression of all EP receptors was detected in the normal sciatic nerve, and EP2 expression increased after SNI. Finally, Nano PGE1 promoted ERK1/2 and Akt phosphorylation. These findings suggest that PGE1 released from nanoparticles accumulates at sites of nerve injury and increases VEGF production by augmenting ERK1/2 phosphorylation via EP receptor signaling, thus promoting tissue repair and regeneration.

The present study conducts the phase analysis, microstructural characteristics, and mechanical property evaluation on the as-cast and quenched Ti-15Mo-xFe alloys with high iron content ranging from 4 to 12 weight percent. All the four alloys were produced in a button-arc melting furnace. Heat treatment in the form of solution treatment was performed in a muffle furnace at a temperature of 1100°C, with a 1-hour holding time. The samples were rapidly quenched in ice-brine. Various characterization techniques were used to analyze samples both in the as cast and quenched conditions. X-ray diffractometer (XRD) was used to analyses the phases present in each alloy whereas the optical microscope (OM) was employed to track the microstructural evolution. The mechanical properties of the alloys were evaluated using a tensile test method while the micro-Vickers hardness measurements were conducted to evaluate hardness of the alloys. OM micrographs revealed equiaxed β grains and substructures in as-cast TMF0, dendritic structure, and equiaxed β grains with pores forming around the grain boundaries in TMF1, and micrograph full of dendrites and pores was observed in the as-cast TMF2 and TMF3 alloys. The quenched TMF0 showed only β equiaxed grains whereas TMF1, TMF2, and TMF3 revealed micrographs full of equiaxed grains of β phase with pores throughout the grain boundaries. The XRD patterns of cast TMF0 showed peaks belonging to the β and orthorhombic α″ martensitic phases and the quenched sample showed the bcc β phase only. The TMF1, TMF2, and TMF3 alloys in as-cast condition indicated peaks belonging to β , α″ and intermetallic B2 TiFe phases, however, their quenched samples showed the presence of β and Fe·Ti·O2 phases in TMF2 and TMF3 alloys. The tensile properties such as ultimate tensile strength (UTS) and elastic modulus (E) of as-cast TMF0 were 264 MPa and 79 GPa and these properties changed upon quenching to 411 MPa and 66 GPa respectively. The elastic modulus of TMF1 in as-cast condition was 74 GPa. The UTS and E of TMF1, TMF2, and TMF3 in as cast and quenched conditions were not recorded due to the fragility of the samples that failed prior to yielding any useful data. The micro-Vickers hardness in as cast and quenched conditions showed a similar trend with hardness increasing slightly upon quenching for TMF0, TMF1, and TMF3 alloys but slightly decreased in the case of TMF2. 6). The fracture surfaces of TMF0 exhibited both ductile and brittle fracture in as cast and quenched conditions whereas the only brittle fracture mode was observed in the TMF1, TMF2 and TMF3 alloys in both conditions.

Behavioral instability is a new concept used for indicating environmental stress based on behavioral traits. This study investigates the possibility of using behavioral instability as a tool for assessing personality in captive animals. The understanding of personality in captive animals can be a resourceful tool in the development of enrichment programs in order to improve animal welfare. In this study it is examined how an olfactory stimulus affects the behavior of two individuals of the species Ursus maritimus in captivity. When using continuous focal sampling throughout the day it was for many behaviors found that the individuals responded differently to stimuli, indicating that there was a difference in personality. This is shown using multiple approaches. One approach used traditional methods for behavioral analyses and the other approach used the concept of behavioral instability as a new quantitative method. This study proves use of behavioral instability as a new quantitative method for investigating personality, expanding the possibility of comparing personality between species. Moreover, it is shown that outliers, which cause asymmetric distributions, should not be removed in behavioral analysis without careful consideration.

In this work, we investigated the effects of heat treatment on the microstructure, hydrogen storage characteristics and corrosion rate of a Ti₃₄V₄₀Cr₂₄Fe₂ alloy. The arc melted alloy was divided into three samples, two of which were separately quartz-sealed under vacuum and heated to 1000 °C for 1 h; one of these samples was quenched and the other furnace cooled to ambient temperature. The crystal structures of the samples were studied via X-ray diffractometry and scanning electron microscopy. Absorption/desorption characteristics were investigated using a Sievert apparatus. Potentiostat corrosion tests on the alloys were performed using an AutoLab^® corrosion test apparatus and electrochemical cell. All samples exhibited a mixture of body-center-cubic (BCC) and Laves phase structures. The corrosion rate, maximum absorption, and useful capacities increased after both heat treatments. The annealed sample had the highest absorption and reversible capacity. The plateau pressure of the as-cast alloy increased after quenching. The corrosion rate increased from 0.0004 mm/y in as-cast sample to 0.0009 mm/y after annealing and 0.0017 mm/y after quenching, due to a decrease in the Cr-content of the C14 phase.

Hydroalcoholic extracts from Malbec and Torrontés wine pomace (Vitis vinifera L.) originating from the high-altitude vineyards of Argentina's Calchaquí Valleys were characterized. Total phenolics, hydroxycinnamic acids, orthodiphenols, anthocyanins, non-flavonoid phenolics, total flavonoids, flavones/flavonols, flavanones/dihydroflavonols, and tannins were quanti-fied through spectrophotometric methods, with Malbec extract exhibiting higher concentra-tions in most of phytochemical groups when compared to Torrontés. HPLC-DAD identified more than 30 phenolic compounds in both extracts. Malbec displayed superior antiradical ac-tivity (ABTS cation, nitric oxide, and superoxide anion radicals), reduction power (iron, copper and phosphomolybdenum), hypochlorite scavenging, and iron chelating ability, compara-tively to Torrontés. The cytotoxicity assessments revealed that Torrontés affected the viability of HT29-MTX and Caco-2 colon cancer cells by 70% and 50%, respectively, at the highest tested concentration (1 mg/mL). At the same time, both extracts did not demonstrate acute toxicity in Artemia salina or in red blood cell assays at 500 µg/mL. Both extracts inhibited the lipoxygen-ase enzyme, with Malbec also reducing the tyrosinase activity and neither inhibited the xan-thine oxidase. The substantial phenolic content and diverse biological activities in Calchaquí Valleys' pomaces underline their potentialities to be valorized for pharmaceutical, cosmetic, and food industries.

Samples of ZrO2 ceramics with different concentrations of impurity titanium ions were synthesized by mixing powders of zirconium and titanium oxides in various mass ratios. The phase composition and surface morphology of the studied ceramics were determined by X-ray phase analysis and scanning electron microscopy. It was found that irradiation of samples with xenon ions (220 MeV) with fluences 1010 and 1012 ion/cm2 leads to a decrease in the intensity of the pulse cathodoluminescence band at 2.5 eV. It is shown that ion irradiation causes the appearance of a new peak of thermoluminescence at 450-650 K of a non-elementary form associated with radiation-induced traps of charge carriers. In contrast to electron irradiation, an increase in the fluence of ions leads to a decrease in the intensity of this peak. In contrast to electron irradiation, an increase in the fluence of ions leads to a decrease in the intensity of this peak. A complex nonmonotonic dependence of the cathode and thermoluminescence intensity on the dopant concentration was found, which may be due to the effects of concentration quenching and aggregation of defective centers.

Microalloying of low carbon steel with niobium (Nb) and titanium (Ti) is standardly applied in high-strength low-alloy (HSLA) steels enabling austenite conditioning during thermo-mechanical controlled processing (TMCP), which results in pronounced grain refinement in the finished steel. The metallurgical effects of microalloying elements are related solute drag and precipitate particle pinning, both acting on the austenite grain boundary thereby delaying or suppressing recrystallization of the deformed grain. In that respect it is important to better understand the precipitation kinetics as well as the precipitation sequence in a typical Nb-Ti-microalloyed steel. Various characterization methods have been utilized in this study for tracing microalloy precipitation after simulating different austenite TMCP conditions in a Gleeble apparatus. Atom probe tomography (APT), scanning transmission electron microscopy in a focused ion beam equipped scanning electron microscope (STEM-on-FIB) and electrical resistivity measurements provide complementary information on the precipitation status and are correlated with each other. It will be demonstrated that accurate electrical resistivity measurements can monitor the general consumption of solute microalloys (Nb) during hot working which was complemented by APT measurements of the steel matrix. On the other hand, STEM revealed that a large part of Nb-containing particles during hot working are co-precipitated with titanium during cooling from the austenitizing temperature. Precipitates that form during cooling or isothermal holding can be distinguished from strain-induced precipitates by corroborating STEM measurements with APT results. APT specifically allows obtaining detailed information about the chemical composition of precipitates as well as the distribution of elements inside the particle. Electrical resistivity measurement, on the contrary, provides macroscopic information on the progress of precipitation and can be calibrated by APT. The current paper highlights the complementarity of these methods and shows first results within the framework of a larger study on strain-induced precipitation.

The exploring comprehensive review of cutting-edge techniques for securing cloud-stored data and managing sensitive information in the context of smart cities through the application of Ciphertext-Policy Attribute-Based Encryption (CP-ABE). It highlights the innovative integration of blockchain technology with CP-ABE, which introduces a decentralized and tamper-resistant key management system, thereby enhancing the overall security framework in cloud environments where data sharing is prevalent. Introducing an online/offline multi-authority CP-ABE scheme, characterized by hidden policies, offers significant advancements in protecting user attributes and access structures, ensuring that sensitive information remains confidential even during encryption and decryption processes. This dual approach not only fortifies security but also optimizes the efficiency of data-sharing mechanisms. Furthermore, the paper delves into implementing hidden sensitive policies and keyword search techniques within smart city infrastructures, which are designed to facilitate secure and efficient data retrieval. These techniques ensure that while data remains accessible to authorized users, privacy is rigorously maintained. Collectively, these approaches represent significant strides in bolstering the security and confidentiality of data in both cloud-based and smart city applications, addressing the growing demand for robust and efficient data management solutions in increasingly interconnected environments.

In the paper, the effect of voltage increasing (from 500 VDC up to 650 VDC) on the structure and chemical composition of porous coating on titanium made by Plasma Electrolytic Oxidation, is presented. In the present paper, phosphates based coatings enriched with calcium, magnesium, zinc and copper in electrolyte based on 1 L of 85% concentrated H3PO4 with additions of Ca(NO3)2·4H2O, and Mg(NO3)2∙6H2O, and Zn(NO3)2∙6H2O, and Cu(NO3)2∙3H2O, are described. The morphology, chemical and phase composition, are evaluated using SEM, EDS, XRD, XPS, GDOES. Based on all the analyses, it was found out that the PEO coatings are porous and enriched with calcium, magnesium, zinc and copper. They consist mainly of the amorphous phase, which is more visible for higher voltages, and it is correlated with the increasing of the total PEO coating thickness (the higher the voltage, the thicker the PEO coating). However, for 650 VDC an amorphous phase and titanium substrate was also recorded with a signal from Ti2P2O7 crystalline, that was not observed for lower voltages. It was also found out that all the obtained coatings may be divided in three sub-layers, i.e. porous, semiporous, and transition one.

The bimetallic (Ta/(Ti, V, Co, Nb) mesoporous MCM-41 nanoparticles were obtained by direct synthesis and hydrothermal treatment. The obtained mesoporous materials were characterized by XRD, XRF, N2 adsorption/desorption, SEM, TEM, XPS, Raman, UV-Vis, PL spectroscopy. A more significant effect was observed on mesoporous structure, typi-cally for MCM-41, and optic properties if the second metal (Ti, Co) does not belong to the same Vb group with Ta as V, Nb. The obtained new nanoparticles were used as catalysts for oxidation with H2O2 of olefinic compounds (1,4 cyclohexadiene, cyclohexene, styrene) and photodegradation of organic pollutants (phenol, methyl orange) from water. The re-sults showed improving of activity and selectivity in oxidation reactions by addition of the second metal to Ta-MCM-41 catalyst. The slow addition of H2O2 was also be benefit for the selectivity in epoxide products and stability of the catalysts. The band gap energy values decrease in the presence of the second metal and the band edge diagram evidenced posi-tive potential for all the conduction band of the bimetallic samples except TaTi-MCM-41. The higher photocatalytic degradation was obtained for samples with TaTi and TaV.

Current progress in the prediction of mechanical behavior of solids requires understanding of spatiotemporal complexity of plastic flow caused by self-organization of crystal defects. It may be particularly important in hexagonal materials because of their strong anisotropy and combination of different mechanisms of plasticity, such as dislocation glide and twinning. These materials often display complex behavior even on the macroscopic scale of deformation curves, e.g., a peculiar three-stage elastoplastic transition, the origin of which is a matter of debates. The present work is devoted to a multiscale study of plastic flow in α-Ti, based on simultaneous recording of deformation curves, 1D local strain field, and acoustic emission (AE). It is found that the average AE activity also reveals three-stage behavior, but in a qualitatively different way depending on the crystallographic orientation of the sample axis. On the finer scale, the statistical analysis of AE events and local strain rates testifies to an avalanche-like character of dislocation processes, reflected in power-law probability distribution functions. The results are discussed from the viewpoint of collective dislocation dynamics and are confronted to predictions of a recent micromechanical model of Ti strain hardening.

In the present work, the effects of ageing treatment on the microstructures of a near-β Ti alloy (TC18) are studied. The influence of ageing treatment on the tensile properties and failure mechanisms are systematically analyzed. It is found that the size and morphology of the primary α (αp) phases are insensitive to ageing temperature and time. Furthermore, the ageing temperature and time dramatically influence the precipitation of the secondary α (αs) phases. Massive αs phases precipitate and gradually coarsen, and finally weave together with increasing the ageing temperature or extending the ageing time. The thickness of αs phases is responsible for the material strengths, while the content of α phases can enhance the material ductility. The ductile characteristics of the alloy with coarser αs phases are more obvious than those with thinner αs phases. Therefore, the ageing treatment is helpful for the precipitation and homogeneous distribution of αs phases, which is essential for balancing the strengths and ductility of the studied Ti alloy.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

In this study, a 5vol. % (TiBw+TiCp)/Ti composite pancake with a diameter of 260mm was prepared by casting followed by open die forging in (α+β) phase region. The microstructures of the composite pancake are inhomogeneous, in terms of both matrix microstructure and distribution of reinforcements. The matrix microstructures were gradually refined from the periphery to centre of the pancake. The TiBw and TiCp reinforcements tend to be uniformly distributed in the centre region and. It is suggested that the microstructure difference can be mainly ascribed to the temperature variation from the periphery to the centre. Additionally, tensile testing results showed that the centre region of the composite pancake exhibits higher strength than the peripheral region. The strengthening mechanism and the softening behavior of the composite pancake with temperature is discussed.

The feral mink population in Denmark consists of two groups of animals; mink born in the wild and mink that have recently escaped from farms. The aims of this study are; 1) to estimate the reproduction and mortality of wild-born and captive-born mink and 2) to estimate the age of mink based on the width of pulp cavity (% of tooth width) in the canine teeth. During 2018, 247 wild caught mink were sent for necropsy at the Danish National Veterinary Institute. Of these mink, 112 were determined as captive-born and 96 were determined wild-born. The mean litter size ± SE of wild-born females was 7.6 ± 0.9 (range: 5-11 kits) and for captive-born females 5.9 ± 0.9 (range: 1-10 kits). The best fitting regression line for mink age (in months) based on pulp width was y=0.42x2-11.52x+104.7, R² = 0.77, p&lt; 0.0001. Individuals with a pulp cavity width &lt;35% was found to be younger than one year. The turnover of mink caught in nature was estimated to 66% and the yearly mortality to 69%, therefore the population is slightly declining. In conclusion, a feral reproducing mink population in Denmark persists, besides the continues influx of captive-born mink escaped from farms.

Background: In 2023, ChatGPT-4 has been impactful across several sectors including healthcare, where it aids in medical information analysis and education. Electronic Patient-Reported Outcomes (ePROs) play a crucial role in monitoring cancer patients’ post-treatment symptoms, enabling early in-terventions. However, managing the voluminous ePRO data presents significant challenges. This study assesses the feasibility of utilizing ChatGPT-4 for analyzing side effect data from ePROs. Methods: Thirty cancer patients were consecutively collected via a web-based ePRO platform, reporting side effects over 4 weeks. ChatGPT-4, simulating oncologists, dietitians, and nurses, analyzed this data and offered improvement suggestions, which were then reviewed by professionals in those fields. Results: Two oncologists, two dieticians and two nurses evaluated the AI’s performance across roles with 540 reviews. ChatGPT-4 excelled in data accuracy and completeness, and was noted for its empathy and support, enhancing communication and reducing caregiver stress. It was particularly effective as a dietician. Discussion: ChatGPT-4 shows promise in processing ePRO data with high accuracy, suggesting that AI can enhance clinical decision-making. Nevertheless, its limitations in emotional engagement highlight the need for AI to supplement, not replace, human care. Emphasizing the role of dietitians underscores the importance of nutritional advice in cancer care. Future studies will further explore the feasible application of AI and ePRO in cancer care clinical processes.

When developing bone implants Young's modulus is one of the primary characteristics of the material that should be considered. The study focuses on the possibility of regulating the modulus of the alloy Ti-50.8 at % Ni by varying its initial structure as well as aging-induced microstructure in a wide range. Microstructure observations were performed using TEM and SEM observations. The calorimetric studies of martensitic transformations were carried out using "Mettler Toledo 822e". Tensile tests were performed in a test temperature range of ‒196≤T≤+100°C using an «IN-STRON 5966». The grain/subgrain size of B2-austenite strongly affects the modulus magnitude. This effect is ambiguous for a material with a grain size of 0.13–3 µm and depends on the test temperature. The effectiveness of aging on the modulus reduction depends on the initial structure: it is most pronounced in an alloy with a relatively coarse grain size of 9 µm and brings a decrease by 3.8 times at a temperature of 37°C. Bone-like elastic modulus (10–30 GPa) at a human body temperature of 37°C is realized in an aged fine-grained NiTi alloy. An ultrafine-grained sub-structure exhibits he same values of Young's modulus in the temperature range from -100°С to 25°С.

Fatigue in any material is a result of continuous irreversible degradation process. Traditionally, fatigue life is predicted by extrapolating experimentally curve fitted empirical models. In the current study, unified mechanics theory is used to predict fatigue life of Ti-6Al-4V under monotonic tensile, compressive and cyclic load conditions. The unified mechanics theory is used to derive constitutive model for fatigue life prediction using a three-dimensional computational model. The proposed analytical and computational models have been used to predict the low cycle fatigue life of Ti-6Al-4V alloys. It is shown that the unified mechanics theory can be used to predict fatigue life of Ti-6Al-4V alloys by using simple predictive models that are based on fundamental equation of the material, which is based on thermodynamics associated with degradation of materials.

The Ti-6Al-4V alloy is widely used in the manufacture of components that should have low density, high corrosion resistance, and fatigue strength. The fatigue strength can be improved by surface modification. The aim of this study was to determine the influence of plasma nitriding on the fatigue behavior of Ti-6Al-4V alloy with a lamellar microstructure (Widmanstätten type). Nitriding was executed at 720 °C for 4 hours in an atmosphere with N₂, Ar and H₂. Samples microstructure characterization was carried out by X-ray diffraction analysis, optical microscopy and scanning electron microscopy. The average roughness of the specimens was determined, and fatigue tests were executed in a bending-rotating machine with reverse tension cycles (R= -1). X-ray diffraction analysis revealed the matrix phases α and β, and the phases Ɛ-Ti₂N and δ-TiN in the nitrided alloy. A nitrogen diffusion layer was formed between the substrate and the titanium nitrides. Plasma nitriding resulted in an increase in low cycle fatigue strength, whereas at high cycles, both conditions exhibit similar behavior. The fracture surface of the fatigue tested specimens clearly revealed the lamellar microstructure. The fracture mechanism appears to be due to cracking at the interface of α and β phases of the lamellar microstructure.

Increasing population size and income growth are causing and increasing demand for food and protein of animal origin. Insects are an interesting alternative to conventional animal source proteins as they can convert by-products from the agricultural industry to biomass for commercial feed for livestock and potentially as a food source for human consumption. Microorganisms have been found to affect insects and can be accumulated via horizontal and vertical transmission. This study aimed to identify if the removal of egg- and substrate-associated microorganisms impact larval performance through the following parameters: development of biomass, final biomass, and the survival rate of house fly (Musca domestica) larvae. Four treatments were tested on substrate consisting of 10.81% alfalfa (Medicago sativa), 21.62% wheat bran (Triticum aestivum), and 67.57% water: (A) disinfected eggs and non-autoclaved substrate, (B) non-disinfected eggs and autoclaved substrate, (C) disinfected eggs and autoclaved substrate, and (D) a control without any removal of microbiota. The results showed a significant decrease in final biomass for the treatments with only disinfected eggs, only autoclaved substrate and both when comparing to the control, and a significant decrease in survival rate for B and D. Moreover, the development of biomass showed a significant difference between days within all treatments. Together this suggest that microorganisms of housefly eggs and the growth substrate plays an important role for growth, which is critical in commercial insect production. Further studies must be performed to examine these parameters in more commercially relevant substrates.

In this paper a microstrip Wilkinson power divider with a 90^° phase delay at one output port is proposed to obtain circular polarization to feed a dual port RFID antenna. The 90^° phase delay was obtained by embedding an extra quarter wavelength at one port of the Wilkinson power divider. The feeding circuit is then mounted on the ground plane of the microstrip antenna feeding the radiating patch directly through the ground plane and dielectric layer thus reducing any fringing effect and resulting a mechanically compact unit. The proposed feeding method offers better expectation of antenna performance with minimal attenuation and coupling losses. The design process generalizes geometric pa- rameters of the Wilkinson power divider for variable port distances. The paper considers both UK and US RFID center frequencies, 870 MHz and 915 MHz respectively. Numeri- cally computed values for geometric design parameters for both frequencies are tabled as future design tools for port distances varying from 18 mm up to 34 mm at 870 MHz and 17 mm up to 32 mm at 915 MHz. Simulation results indicate a return loss (S11) of -20 dB and -26 dB at 870 MHz and 915 MHz operational frequencies respectively at 270^° angled quarter wavelength.

Additive manufacturing (AM) techniques are widely investigated for the cost-effective use of titanium (Ti) alloys in various aerospace applications. One of the AM techniques developed for such applications is plasma transferred arc solid free-form fabrication (PTA-SFFF). Materials manufactured through AM techniques often exhibit anisotropies in mechanical properties due to the layer-by-layer material build. In this regard, the present study investigates the isothermal directional fatigue of Ti-TiB metal matrix composite (MMC) manufactured by PTA-SFFF. This investigation includes rotating beam fatigue test, electron microscopy, and fatigue calculations. The fatigue experiments were performed at 350 ºC using specimen with the test axis oriented diagonally (45º) and parallel (90º) to the AM builds directions. The fatigue values from the current experiments along with literature data find that Ti MMC manufactured via PTA-SFFF exhibit fatigue anisotropy reporting highest strength in 90º and lowest in perpendicular (0º) AM build directions. Further, the electron microscopy investigations on 0º, 45º, and 90º AM build specimens reveal frequent TiB clusters in all three AM build directions and suggest that the spread of these TiB clusters play a role in fatigue anisotropy. Moreover, the fatigue calculations were performed using both the Paris’ and recently reported modified Paris’ equations. Comparison of R^2 values for these calculations show that modified Paris’ equation predicts the fatigue life of AM Ti-TiB MMC more accurately than the Paris’ equation.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

TiNbZrTa alloys are promising for multidisciplinary applications, such as refractory and biomedical purposes due to their high thermal stability and non-toxicity. Hardness and elastic modulus are among the key features for their adequate industrial applications. The influence of porosity and Ti/Ta ratio were investigated on TiNbZrTa alloys produced by three different processing routes, i.e., (i) blend element and posterior press and sintering (BE + P&amp;S), (ii) mechanical alloying with press and sintering (MA + P&amp;S), and (iii) arc melting and casting. Atomic diffusion was improved during processing, resulting in lower porosity in the following order: casting &lt; MA + P&amp;S &lt; BE + P&amp;S. Ta offered limited atomic diffusion due to its high melting point compared to other constituent elements. Thus, the total porosity of alloys increased with increasing the Ta contents, i.e., by lowering the Ti/Ta ratio. However, the Ti/Ta ratio did not considerably affect the bonding energy or the elastic modulus. Hardness was increased significantly in dense alloys compared to the porous ones. However, porosity and Ti/Ta ratio did not show a clear trend in hardness among the porous alloys.

Cyclic olefin copolymer (COC) is a novel type of thermoplastic polymer gaining the attention of the scientific community in electronic, optoelectronic, biomedicine and packaging applications. Despite the benefits in the use of COC like undoubted optical transparency, chemical stability, good water-vapor barrier and biocompatibility, its original hydrophobicity restricts its wider applicability and optimization of its performances. Presently, we report on the optical, and morphological properties of the films of COC covered with Ti in selected areas. The layer of Ti on COC was deposited by pulsed lased deposition processing. The Ti/COC film was characterized by UV-Vis spectroscopy indicating that its transmittance in the visible region decreased by about 20% with respect to the pristine polymer. The quality of the deposited Ti was assessed with the morphology by scanning electron (SEM) and atomic force microscopies (AFM). The modification of the wettability was observed by the sessile drop method indicating a reduction of the native hydrophilicity.

Intestinal mucositis (IM) is a common adverse effect of chemotherapy, limiting its clinical application. Edible Chinese medicine, specifically Codonopsis pilosula-derived CP-A, with anti-inflammatory and gastrointestinal protective effects. The present work was to investigate CP-A's role in ameliorating IM and its mechanism using in vitro and rat models. Western blot, immunohistochemical (IHC) and real-time PCR (RT-PCR) analyses were used to assess protein expression related to the extracellular-regulated protein kinases (ERK)/myosin light chain kinase (MLCK)/myosin light chain 2 (MLC2) signaling pathway and tight junction proteins. Enzyme-linked immunosorbent assay (ELISA) was conducted to measure inflammatory factors, and 16S rRNA Amplicon Sequencing was employed for cecum content analysis. The results indicated that CP-A could restore body weight, food intake and histopathological changes in IM rats. Besides, abnormal MLCK activation induced by 5-fluorouracil (5-FU) was attenuated by CP-A via the ERK/MLCK/MLC2 pathway. CP-A treatment improved tight junction protein levels and reduced inflammatory factor expression. On the other hand, intestinal flora experiment demonstrated that CP-A intervention could increase the abundance of lactobacillus. In conclusion, CP-A mitigates 5-FU-induced IM by inhibiting the ERK/MLCK/MLC2 pathway, reducing the expression of inflammatory factors, improving the intestinal mucosal barrier and regulating intestinal flora. This study sheds light on CP-A's therapeutic potential in IM treatment, providing insights for future research.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

Drones equipped with thermal cameras have recently become readily available, broadening the possibilities for monitoring wildlife. The European hare (Lepus europaeus) is a nocturnal mammal that is closely monitored in Denmark due to populations declining since the mid-1900s. The limitations of current population assessment methods, such as spotlight counts and hunting game statistics, could be overcome by relying on drone surveys with thermal imaging for population counts. The aim of this study was to investigate the use of a DJI Mavic 2 Enterprise Advanced drone with thermal imaging as a tool for monitoring the Danish hare population. Multiple test flights were conducted over agricultural areas in Denmark in spring 2022, testing various flight altitudes, camera settings, and recording methods. The test flights were used to suggest a method for identifying and counting hare. The applied use of this methodology was then evaluated through a case survey that had the aim of identifying and counting hare over an agricultural area of 242 ha. Hare could be detected with thermal imaging at flight altitudes up to 80 m and it was possible to fly as low as 40 m without observing direct behavior changes. Thermal images taken at these altitudes also provided enough detail to differentiate between species and animal body size proved to be a good species indicator. The case study confirmed the use of thermal imaging based drone surveys to identify hare and conduct population counts, thus, indicating the suggested methodology as a viable alternative to traditional counting methods.

A series of Ti₄₀Zr₂₅Cu₉Ni₈Be₁₈)_100-xTM_x (x = 0, 1, 2, 3, 4 at.%, TM = Nb, Y) Bulk amorphous alloys were designed and prepared using the copper mold casting method. The microstructures, glass forming ability and mechanical properties of the alloys were investigated by means of X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning colorimetry (DSC), depth-sensitive nanoindentation and uniaxial compressive test. The Bulk amorphous alloys with different ductility were investigated by measuring their plastic deformation energy (PDE) of the first pop-in events during loading. The relationships between the PDE value, shear band formation and ductility in Bulk amorphous alloys have been investigated. The results show that the PDE value decreases by the Nb addition and promotes the generation of multiple shear bands easily, which increase the fracture strength and plasticity significantly. Substituting Nb with Y has exactly the reverse effect. A useful rule for preparing of Bulk amorphous alloys with high plasticity is herein proposed, whereby the chemical composition of the Bulk amorphous alloys can be tailored to possess a lower PDE value.

This study investigates the potential benefits of integrating coarser particle size distributions (PSDs) of 45-106 µm into laser-based powder bed fusion of metals (PBF-LB/M), aiming to reduce costs while maintaining quality standards. Despite the considerable advantages of PBF-LB/M in producing intricate geometries with high precision, the high cost of metal powders remains a barrier to widespread adoption. By exploring the use of coarser PSDs, particularly from electron beam-based powder bed fusion of metals (PBF-EB/M), significant cost-saving opportunities are identified. Through comprehensive powder characterization, process analysis, and mechanical property evaluation, this study demonstrates that PBF-LB/M can effectively utilize coarser powders while achieving comparable mechanical properties to those produced with 20-53 µm PSD. Adaptations in process parameters enable the successful processing of coarser powders, maintaining high-relative density components with minimal porosity. Additionally, market surveys reveal substantial cost differentials between PBF-LB/M and PBF-EB/M powders, indicating 40 % cost reduction potential by integrating coarser PSDs into PBF-LB/M. Overall, this study provides valuable insights into the economic and technical feasibility of printing with coarser powders in PBF-LB/M, offering promising avenues for cost reduction without compromising quality, thus enhancing competitiveness and adoption of the technology in manufacturing applications.

The exchange coupling between two ferromagnetic thin films, one with magnetically hard and the other with soft phases, separated by a thin non-magnetic layer is studied. Nd-Fe-B/ Ti / Fe thin film heterostructures were fabricated using DC magnetron sputtering on Si substrates which were heated in situ at 650°C using a house-built vacuum-compatible heater. The effect of the thickness of the Ti buffer layer and the annealing temperature on the formation of various phases of NdFeB was investigated. The effect of the thickness of the non-magnetic Ti spacer layer on the exchange coupling strength between the hard phase Nd-Fe-B ferromagnetic thin layer and the soft phase transition metal Fe layer was experimentally investigated. Hysteresis loops of multilayer thin films indicate an antiferromagnetic coupling was observed when the thickness of the spacer layer was 2 nm. This is within the range of antiferromagnetic coupling calculation based on RKKY theory predictions.

Magnetic force microscopy (MFM) is a widespread technique for imaging magnetic structures with a resolution of some 10 nanometers. MFM can be calibrated to obtain quantitative (qMFM) spatially resolved magnetization data in units of A/m by determining the calibrated point spread function of the instrument, its instrument calibration function (ICF), from a measurement of a well-known reference sample. Beyond quantifying the MFM data, a deconvolution of the MFM image data with the ICF also corrects the smearing caused by the finite width of the MFM tip stray field distribution. However, the quality of the calibration depends critically on the calculability of the magnetization distribution of the reference sample. Here, we discuss a Ti/Pt/Co multilayer stack which shows a stripe domain pattern as a suitable reference material. A precise control of the fabrication process combined with a characterization of the sample micromagnetic parameters allows to reliably calculate the sample’s magnetic stray field, proven by a very good agreement between micromagnetic simulations and qMFM measurements. A calibrated qMFM measurement using the Ti/Pt/Co stack as a reference sample is shown and validated and the application area for quantitative MFM measurements calibrated with the Ti/Pt/Co stack is discussed.

In this work, the ternary titanium, copper and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by x-ray diffraction (XRD), nanoindentation (modulus and hardness) and Atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel.

The developed microstructure features a long with mechanical properties in vacuum brazing of commercially pure Ti-alloy using Ti₂₀Zr₂₀Cu_60-x-Ni_x (x=10, 20, 30, 40 and 50) metallic filler. Brazing temperatures and holding times employed in this study were 1240-1279 K (967-1006^oC) for a period of 10 min, respectively. The mechanical properties of brazed joints were evaluated by nanoindention at a constant peak load of 5000 μN and tensile tests. The number of intermetallic phase, such as NiTi₂, Ti₂Cu, (Ti, Zr)₂Cu, (Ti, Zr)₂Ni, β(Ti, Zr), α-Ti and NiTi. The solid solution matrix have been identified at 1279 K out of these different regions the NiTi₂ rich region had the highest nanohardness of 17 GPa, It is interesting to note that among five different glasses, the Ti₂₀Zr₂₀Cu₁₀Ni₅₀ has the highest yield strength of 17 GPa, which is mainly due to NiTi₂ phase. Based on the tensile test results all cracks propagate along the brittle intermetallic compounds like NiTi₂ in the reaction layer the reduction of the strength of the joints and fracture behaviour upon propagation of the crack, which shows the morphological cleavage including facets characteristics.

Selection of the most suitable material is one of the key decisions to be taken at the design stage of a manufacturing process. Traditional approaches as Ashby maps based on material properties are widely used in the industry. However, in the production of multimaterial components, the criteria for the selection can include antagonistic approaches. The aim of this work is the implementation of a methodology based on the results of process simulations for several materials and classify them by applying an advanced data analytics method based on Machine Learning (ML), in this case the Support Vector Regression (SVR) and Multi-Criteria Decision Making (MCDM) methodolo-gies, in this case Multi-criteria Optimization and Compromise Solution (VIKOR) combined with Entropy weighting methods. In order to do this, a Finite Element Model (FEM) has been built to evaluate the extrusion force and the die wear in a multi-material co-extrusion process of bimetallic Ti6Al4V-AZ31B billets. After applying SVR and VIKOR combined with Entropy weighting methodologies, a comparison has been established based on the material selection and complexity of the methodology used, resulting that material chosen in both methodologies is very similar and MCDM method is easier to implement because there is no need of evaluate the error of the pre-diction model and the time for data preprocessing is less than the time needed in SVR.

The high Nb-containing TiAl-based alloy ingot beyond laboratory scale with a composition of Ti-46Al-8Nb (at. %) was prepared by a vacuum induction melting process based on BaZrO3 refractory. An ingot without macroscopic casting defects (such as pipe shrinkage and center line porosity) was finally obtained, and the chemical composition, solidification path, microstructure and tensile properties of the ingots were investigated. The results show that the deviations of Al and Nb content along a 430 mm long central part of the ingot are approximately \mathrm{\pm}0.39 at. % and \mathrm{\pm}0.14 at. %, and the oxygen content in the ingot can be controlled at around 1000 ppm. During the solidification process, the alloy suffered from peritectic reaction and formed columnar grains with anisotropy. In addition to Al segregation and Nb segregation, β-phase particles associated with γ phase at the triple junction of the colonies were observed. Moreover, the mechanical properties of the ingot in the transverse direction are significantly better than those in the longitudinal direction, with a tensile strength of up to high as 700 MPa and a corresponding fracture elongation of 1.1 %.

Selective laser melting (SLM) is one of the widely used techniques in metallic additive manufacturing, in which high-density laser powder is utilized to selectively melting layers of powders to create geometrically complex parts. Temperature distribution and molten pool geometry directly determine the balling effect, and concentrated balling phenomenon significantly deteriorates surface integrity and mechanical properties of the part. Finite element models have been developed to predict temperature distribution and molten pool geometry, but they were computationally expensive. In this paper, the three-dimensional temperature distributions are predicted by analytical models using point moving heat source and semi-ellipsoidal moving source respectively. The molten pool dimensions under various process conditions are obtained from the three-dimensional temperature predictions and experimentally validated. Ti-6Al-4V alloy is chosen for the investigation. Good agreements between the predictions and the measurements are observed. The presented models are also suitable for other metallic materials in the SLM process.

Continuous ultrasonic in-situ monitoring for industrial applications is difficult owing to the high operating temperatures in industrial fields. It is expected that ultrasonic transducers consisting of CaBi4Ti4O15(CBT)/Pb(Zr,Ti)O3(PZT) sol-gel composite could be one solution for ultrasonic nondestructive testing (NDT) above 500 C because no couplant is required and CBT has a high Curie temperature. To verify the high temperature durability, CBT/PZT sol-gel composite films were fabricated on titanium substrates by spray coating, and the CBT/PZT samples were tested in a furnace at various temperatures. Reflected echoes with a high signal-to-noise ratio were observed up to 600 C. A thermal cycle test was conducted from room temperature to 600 C, and no significant deterioration was found after the second thermal cycle. To investigate the long-term high-temperature durability, a CBT/PZT ultrasonic transducer was tested in the furnace at 600 °C for 36 h. Ultrasonic responses were recorded every 3 h, and the sensitivity and signal-to-noise ratio were stable throughout the experiment.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for Ti-6Al-4V by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as, feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error, material removal rate and power consumption the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, radial depth of cut. Finally, confirmation tests were carried out to make a comparison between the experimental results. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

To obtain smooth coatings of TiO2 for building a new design of Ti-6Al-4V heart valve, the anodic oxidation technique in pre-spark conditions was evaluated. TiO2 coating is necessary for its recognize biocompatibility and corrosion resistance. A required feature on surfaces in contact with blood is a low level of roughness (Ra ≤ 50 nm) that not favor the formation of blood clots. The present paper compares the coatings obtained by anodic oxidation of the Ti-6Al-4V alloy using H2SO4 at different concentrations (0.1 M to 4 M) as electrolyte and applying different voltages (from 20 V to 70 V). Color and morphological analysis of coatings are performed using optical and scanning microscopy. The crystalline phases were analyzed by glancing X-ray diffraction. By varying the applied voltage different interference colors coatings were obtained. The differences in morphologies of the coatings, due to the change in concentration, are more evident at high voltages limiting the oxidation conditions for the desired application. Anatase phase was detected from 70 V for 1 M H2SO4. An increase in the concentration of H2SO4 decreases the voltage at which the transformation of amorphous to crystalline coatings occurs, i.e. with 4 M H2SO4 the anatase phase appears at 60 V.

(1) Background If placenta percreta (PP) is suspected, one should take into account ultrasound and MRI data, which allow one to assess not only the depth of invasion of the placenta into the myometrium, but also the degree of involvement of the blood vessels of the uteroplacental region and the pelvis, the formation of adhesions and collaterals between organs as well; (2) Methods: The patient with suspected PP was examined by ultrasound and Magnetic Resonance Imaging (MRI) examination. Histological study was performed on paraffin sections (hematoxylin &amp; eosin, Mallory staining); cytotrophoblast was detected with antibodies to cytokeratin-8; (3) Results MRI and ultrasound examinations showed placental invasion extending beyond the serous lining of the uterus involving the posterior wall of the bladder. Elective abdominal delivery was performed at 37 weeks. Surgical excision of the uterine wall with invaded villi and involved fibrous bladder wall were performed. Histological study revealed invasive cytotrophoblast cells in the uterine wall located up to adventitia of the uterine subserosal vessels only. Thinning of the uterine wall up to the serous membrane was detected; (4) Conclusions: Placental villi and trophoblast extended beyond the uterus is not histology equivalent to placenta percreta. To diagnose PP instrumental visualization methods should be used.

There has been an increased focus on new technologies to monitor habitat use and behaviour of cattle, to develop a more sustainable livestock grazing system, without compromising animal welfare. The currently most used method for monitoring cattle behaviour is tri-axial accelerometer data from systems such as virtual fencing technology or bespoke monitoring technology. This method requires high frequency data, and as such, quickly drains contemporary systems of power making it unsuitable for long-term monitoring. In this paper, we explore the possibility of determining habitat preference and habitat utilisation patterns in cattle, using low frequency activity and location data. We do this by (1) calculating habitat selection ratios, (2) determining daily activity patterns and based on those, (3) inferring grazing and resting sites in a group of cattle wearing virtual fencing collars in a coastal setting with grey, wooded and decalcified dunes, humid dune slacks and salt meadows. We found that GPS data, and a measure of activity, combined with accurate mapping of habitats can be an effective tool in assessing habitat preference. The animals preferred salt meadows over the other habitats, with wooded dunes and humid dune slacks being the least preferred. We were able to identify daily patterns in activity. By comparing general trends in activity levels to existing literature, it was possible to somewhat infer resting and grazing behaviour in the different habitats. According to our inference of behaviour the herd predominantly used the salt meadows for resting and ruminating. The approach used in this study allowed us to use GPS location data for measuring the activity and combine it with accurate habitat mapping in a cheap and effective way, which can be an important tool for guiding management decisions.

The present study investigation, our results on characterization of commercially pure-Ti alloy brazed with metallic glass ribbons of Ti20Zr20Cu60-xNix (x = 30, 40, and 50) metallic glass ribbons were produced using a vacuum melt spinner. These ribbons were then used as filler materials for vacuum brazing of two Ti alloy plates at 1268, 1277 and 1279 K for a period of 10 min. Field-Emission Scanning Electron Microscopy (FESEM), Transmission Electron Microscopy (TEM) and the energy dispersive X-ray spectroscopy (EDX). The as-spun ribbons showed fully amorphous structure when examined on both surfaces by XRD and also verified by TEM investigation. The brazing joint of two Ti-plates using the metallic glass ribbon when brazed with Ni50 was found to be of very high strength. FESEM characterization of the cross-section of the brazed joints shows sub-micron size grains uniformly distributed in the matrix with brighter appearance. FESEM and EDX analysis revealed that the sub-micron grains are rich in Ti & Ni while the matrix phase mainly consisted of Ti. BSE image along with EDS Analysis indicated that the brazed joint has a presence of NiTi2 and Cu2 (Ni Zr) phases which could be responsible for increase in the strength of the brazed joint.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

Friction stir processing (FSP), a severe plastic deformation process, was applied on commercially pure Ti to obtain an improved microstructure. The process yielded a refined microstructure and higher mechanical properties at room temperature (RT). Yet the microstructure was found to contain bright bands demonstrating high hardness values of about 500 HV. High resolution scanning electron microscopy (HRSEM) as well as electron back scattering diffraction (EBSD) analysis indicated that these bands were composed of extra-fine equiaxed α-Ti grains with an average radius of 1-2 microns. In addition, a retained β-phase was detected at the boundaries of these α-Ti grains, together with a small quantity of separate β grains. The results of a fractography study conducted on broken tensile specimens showed that the FSP’ed material was free of defects and that the fracture started at these bands. It is proposed that these bright bands are due to excessive deformation occurring during the processing stage, leading to an accelerated dynamic recrystallization (DRX) process. In turn, these heavy deformation regions act as a strengthening constituent, making the material superior to the parent material as far as its mechanical RT properties are concerned. Consequently, this means that FSP of CP-Ti has the potential to serve as an industrial means of improving the mechanical properties of the material.