A model to rationalize the effects of test temperature and microstructural variables on the creep crack growth (CCG) and creep-fatigue crack growth (CFCG) rates in ferritic steels is described. The model predicts that as the average spacing between grain boundary particles that initiate creep cavities decrease, the CCG and CFCG rates increase. Further, CCG data at several temperatures collapse into a single trend when a temperature compensated CCG rate derived from the model is used. CCG and CFCG behavior measured at different temperatures is used to assess the effects of variables such as differences between basemetal (BM), weldmetal (WM) and the heat-affected zone (HAZ) regions. The model is demonstrated for Grade 22 and Grade 91 steels using data from literature. It is shown that differences between the CCG behavior of Grade 22 steel in new and ex-service conditions are negligible in the BM and WM regions but not in the HAZ region. The CCG behavior of Grade 91 steels can be separated into creep-ductile and creep-brittle regions. The creep-brittle tendency is linked to the presence of excess trace element concentrations in the material chemistry. Significant differences found in the CCG rates between BM and the WM and HAZ regions of Grade 91 steel were explained.

Ti17 alloy is mainly used to manufacture aero-engine discs due to its excellent properties such as high strength, toughness and hardenability. It is often subjected to creep-fatigue cyclic loading in service environments. Shakedown theory describes the state in which the accumulated plastic strain of the material stabilizes after several cycles of cyclic loading, without affecting its initial function and leading to failure. This theory includes three behaviors: elastic shakedown, plastic shakedown, and ratcheting. In this paper, the creep-fatigue tests (CF) were conducted on Ti17 alloy at 300℃ to study its shakedown behavior under creep-fatigue cyclic loading. Based on the plasticity-creep superposition model, a theory model that accurately describes the shakedown behavior of Ti17 alloy was constructed, and ABAQUS finite element software was used to validate the accuracy of the model. TEM analysis was performed to observe the micro-mechanisms of shakedown in Ti17 alloy. The results reveal that the Ti17 alloy specimens exhibit plastic shakedown behavior after three cycles of creep-fatigue loading. The established finite element model can effectively predict the plastic shakedown process of Ti17 alloy, with a relative error between the experimental and simulation results within 4%. TEM results reveal that anelastic recovery controlled by dislocation bending and back stress hardening caused by inhomogeneous deformation are the main mechanisms for the plastic shakedown behavior of Ti17 alloy.

The adapted Posner spatial cue-target paradigm was used to explore the relationship between exogenous temporal attention caused by rhythm and endogenous and exogenous spatial attention. The study was divided into two experiments. In Experiment 1, 33 participants used arrow cues to orient endogenous spatial attention and rhythm to orient exogenous temporal attention. In Experiment 2, with 29 participants, exogenous spatial attention was directed by highlighting the cue box. Exogenous temporal attention was directed by rhythm. Experiment 1 indicated that RTs were faster for attended targets than the unattended. The main effect of temporal attention was significant, with RTs being faster for synchrony and late compared to early. RTs were faster for late compared to synchrony. The main effect of stimulus repetition was significant, with faster RTs for targets when the rhythmic cue consisted of five compared to four. The interaction between spatial attention and temporal attention was not significant. Experiment 2 demonstrated that exogenous spatial attention only exhibited IOR under early four stimulus repetitions. The main effect of temporal attention was significant, with RTs being faster for synchrony and late compared to early. The main effect of stimulus repetition was significant, with faster RTs for targets when the rhythmic cue consisted of five compared to four. The interaction between spatial attention and temporal attention was significant. The results indicated that rhythmic temporal attention supported foreperiod effects. Exogenous temporal attention and endogenous spatial attention independently affect behavior, while exogenous temporal attention and exogenous spatial attention mutually influenced behavior.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Although the Orthotropic steel decks (OSDs) have been widely used in the construction of long-span bridges, there are frequently reported fatigue cracks after years of operation, and the bridge deck overlay also presents severe damage due to OSD crack-induced stiffness reduction. The ultra-high performance concrete (UHPC), recognized as the most innovative cementitious composites and the next generation of high-performance materials, shows high strength, ductility, toughness and well performance on durability. After its first application to the OSD bridge in early 2000s, the orthotropic Steel-UHPC composite deck has been comprehensively studied worldwide. This review will summarize some important studies and findings on behavior and fatigue performance of orthotropic steel-UHPC composite deck. The existing studies and engineering application indicate that such deck system presents good bending behavior and high fatigue performance. The failure mode of shear studs in UHPC layer is dominated by shear fractures. The cracking of UHPC layer shall consider the superposition effect of stress from both the whole bridge structure and local decks. While some reasonable structural details in the traditional OSD may not work for the orthotropic steel-UHPC composite deck. It is recommended to evaluate the stress behavior and structural parameters, as well as fatigue life by conducting the field test under in-service traffic conditions.

Creep deformation in single phase ɤ-TiAl alloy manufactured using different processing techniques has been an extensively studied topic since the late 1970s. The present work revisits the original work on understanding the tensile creep deformation behaviour of wrought single-phase ɤ-TiAl alloy by Hayes and Martin [1] and is aimed to develop an understanding of steady state creep. Besides, it is also aimed to investigate the creep life for stress levels of 69.4 and 103.4 MPa at 832 ^⁰C using Monkman-Grant [2] approach.

Metal creep has been a subject of extensive study for more than 110 years, because it affects the useful life of engineering components operating at high temperatures. It is even more so with ever-increasing operating temperatures of propulsion/power-generation systems by the environmental regulations to reduce greenhouse emissions. This review summaries the recent development in creep modeling with regards to creep strain evolution, creep rate, creep ductility, creep life and fracture mode, attempting to provide a comprehensive mechanism-based framework to address all the important creep phenomena and the long-standing issue of long-term creep life prediction with microstructural evolution and environmental effects.

The Ti-6Al-4V alloy is widely used in the manufacture of components that should have low density, high corrosion resistance, and fatigue strength. The fatigue strength can be improved by surface modification. The aim of this study was to determine the influence of plasma nitriding on the fatigue behavior of Ti-6Al-4V alloy with a lamellar microstructure (Widmanstätten type). Nitriding was executed at 720 °C for 4 hours in an atmosphere with N₂, Ar and H₂. Samples microstructure characterization was carried out by X-ray diffraction analysis, optical microscopy and scanning electron microscopy. The average roughness of the specimens was determined, and fatigue tests were executed in a bending-rotating machine with reverse tension cycles (R= -1). X-ray diffraction analysis revealed the matrix phases α and β, and the phases Ɛ-Ti₂N and δ-TiN in the nitrided alloy. A nitrogen diffusion layer was formed between the substrate and the titanium nitrides. Plasma nitriding resulted in an increase in low cycle fatigue strength, whereas at high cycles, both conditions exhibit similar behavior. The fracture surface of the fatigue tested specimens clearly revealed the lamellar microstructure. The fracture mechanism appears to be due to cracking at the interface of α and β phases of the lamellar microstructure.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

The effects of environmental media on the corrosion fatigue fracture behavior of 25CrMo steel were investigated. The media include air, and a 3.5 wt.% and a 5.0 wt.% NaCl solutions. Experimental results indicate that the media induces the initiation of corrosion fatigue cracks at multiple sites. The multi-cracking sites cause the changes in the crack growth directions, the crack growth rate during the coupling action of the media and the stress amplitude. The coupling effects are important for engineering applications and research. The probability and predictions of the corrosion fatigue characteristic life can be estimated using the 3-parameter Weibull distribution function.

The effect of low cycle fatigue (LCF) pre-damage on the subsequent very high cycle fatigue (VHCF) behavior is investigated in TC21 titanium alloy. LCF pre-damage is applied under 1.8% strain amplitude up to various fractions of the expected life and subsequent VHCF properties are determined using ultrasonic fatigue tests. Results show that 5% of LCF pre-damage insignificantly affects the VHCF limit due to the absent of pre-crack, but decreases the subsequent fatigue crack initiation life estimated by Pairs’ law. Pre-cracks introduced by 10% and 20% of LCF pre-damage significantly reduce the subsequent VHCF limits. The crack initiation site shifts from subsurface-induced fracture for undamaged and 5% of LCF pre-damage specimens to surface pre-crack for 10% and 20% of LCF pre-damage specimens in very high cycle region. The fracture mechanism analysis indicate that LCF pre-crack will re-start to propagate under subsequently low stress amplitude when stress intensity factor of pre-crack is larger than its threshold. Furthermore, the predicted fatigue limits based on EI Haddad model for the LCF pre-damage specimens well agree with the experimental results.

Rare earth rich magnesium alloys are used in aerospace and automotive fields because of their high specific strength and good castability. However, due to their low corrosion resistance, protective surface treatments, such as conversion coating or electroless plating are necessary, when they have to be used in humid or corrosive environments. The present study was aimed to evaluate the effect of Plasma Electrolytic Oxidation (PEO) and different surface roughness (Ra≈0.8 μm and Ra≈0.3 μm) on the rotating bending fatigue of an innovative Mg alloy, with a high content of Nd (up to 3.1 wt%) and Gd (up to 1.7 wt %). Fatigue tests revealed a 15% decrease in the fatigue strength of the PEO treated alloy (fatigue strength = 88 MPa) with respect to the bare alloy (fatigue strength = 103 MPa). The reduction of fatigue strength was mainly due to the residual tensile stresses induced by the PEO treatment. The effect of surface roughness on the bare alloy was, instead, negligible. The mechanisms of crack initiation were similar in the untreated and PEO treated alloy, with crack nucleation sites located in correspondence of large facets of the cleavage planes.

One of the major concerns in structural health management (SHM) is the early detection of a growing crack. Using this, future damage due to crack propagation can be mitigated or eliminated by implementing proper repair and maintenance. Acoustic Emission (AE) is a non-destructive testing (NDT) method with potential applications for locating and monitoring fatigue cracks. The research presented in this paper focuses on SHM using AE. A novel AE signal analysis approach was proposed in order to detect crack initiation and assess small crack lengths. Experimental investigation indicated that initiation of a crack could be identified through the statistical analysis of the resulting features of the AE signals. A probabilistic AE-based model for small fatigue crack sizing was developed and the uncertainties of the model were estimated. In addition, a probabilistic model validation approach was implemented to confirm accurate estimation of the results. The outcome of this research can be used to evaluate the integrity of structures under fatigue loading. The proposed approach can also be applied as an approach to manage health and assess prognosis of structures.

Thermal stresses belong to the leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature properties of asphalt mixtures, three point bending and uniaxial tensile creep tests were applied and the master curves of stiffness modulus were analyzed. On the basis of creep test results, rheological parameters describing elastic and viscous properties of the asphalt mixtures were determined. Thermal stresses were calculated and compared to tensile strength of the material to obtain the failure temperature of the analyzed asphalt mixtures. It was noted that lower strain values of creep curves were obtained for the Tensile Creep Test (TCT) than for the Bending Beam Creep Test (BBCT), especially at lower temperatures. Results of thermal stress calculations indicated that higher reliability was obtained for the viscoelastic Monismith method based on the TCT results than for the simple quasi-elastic solution of Hills and Brien. The highest agreement with the TSRST results was also obtained for the Monismith method based on the TCT results. No clear relationships were noted between the predicted failure temperature and different methods of thermal stress calculations.

In this paper, the deformation behavior of S32750 duplex stainless steel during low cycle fatigue was studied by controlling number of cycles. The microstructure of the specimens under different cycles was characterized by optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). Microhardness of two phases was measured by a digital microhardness instrument. The results showed that the microhardness of ferrite increases significantly after the first 4000 cycles, while the austenite shows a higher strain hardening rate after fatigue fracture, and the microhardness of ferrite and austenite increases by 23 HV and 87 HV, respectively. Two-phase kernel average misorientation (KAM) diagram showed that the continuous accumulation of plastic deformation easily leads to the initiation of cracks inside the austenite and at the phase boundaries. The evolution of dislocation morphology in two phases was obviously different. With the increase of cycle number, the dislocation in ferrite gradually transforms from dislocation bundles and dislocation array to sub-grain structure, while the dislocation in austenite gradually develops from dipole array to ordered Taylor lattice network structure.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Background Hop creep continues to present an unresolved issue for the brewing industry, specifically stemming from those hops added to beer during fermentation. Hops have been found to contain four dextrin-degrading enzymes: alpha amylase, beta amylase, limit dextrinase, and an amyloglucosidase. One recent hypothesis predicts that these dextrin-degrading enzymes could originate from microbes rather than the hop plant itself. Scope and Approach This review begins by describing how hops are processed and used in the brewing industry. It will then discuss hop creep’s origins with a new beer style, antimicrobial factors from hops and resistance mechanisms that bacteria use to counter them, and finally microbial communities that inhabit hops, focusing on whether they can produce the starch degrading enzymes which drive hop creep. After initial identification, microbes with possible links to hop creep were then run through several databases to search the genomes (if available) and for those specific enzymes. Key Findings and Conclusions Several bacteria and fungi contain alpha amylase as well as unspecified glycosyl hydrolases, but only one contains beta amylase. Finally, this paper closes with a short summary of how abundant these organisms typically are in other flowers.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

Cervical cancer is one of the ailments that endangers the health of women all over the world and causes infertility. Fortunately, this disease can be avoided. Both the results and participation rates of the current preventative strategy remain poor. Hence, preventative or early detection methods remain challenging and open. In gynecology and computer science fields, few studies on identifying cervical cancer are based on behavior risk factor and machine learning. Moreover, various social and behavioral aspects might often make it more difficult to detect cervical cancer especially in low‑ and middle‑income countries (LMICs). Accordingly, focus on predicting the presence of cervical cancer through behavioral risk factors is the basic structure of this research. We proposed an approach to classify cervical cancer from a social-behavioral perspective using logistic regression to predict cervical cancer. We got significantly improved outcomes than the existing methods. Moreover, we used feature engineering to formulate less dimensionality as a pre-processing step and optimized parameters to be prepared for classification phase. The results proved that using the logistic regression with regularization type L1 had a promising performance. The accuracy of Logistic Regression (LR) L1 was 97.2%. Such results support the proposed work as a reliable classification predictive tool.

This research presents a comprehensive framework for efficiently generating forest fire datasets from Google Earth Engine data sources. The primary contribution of this work lies in providing a methodology to swiftly extract forest fire factors without the need for permissions or access to private datasets, rendering the dataset openly accessible and shared without barriers. Furthermore, given that the remote sensing data used is a global dataset, it can be applied in any region without restrictions. In this study, Peninsular Malaysia is chosen as a case study to demonstrate the framework's effectiveness. The generated dataset includes essential variables including the climate and environment, landcover, topography, and anthropogenic factors facilitating the analysis of fire occurrences. The methodology empowers data scientists, enabling them to leverage their analytical skills on the extracted dataset without requiring specialized remote sensing knowledge. Additionally, this study also showcases the adoption of large language models, specifically GPT-4 with the Noteable plugin, as a tool for conducting preliminary analyses on the generated dataset. Sample analyses reveal that several key features, including the KBDI, LST, PDSI, climate water deficit, and precipitation, significantly impact forest fire occurrences in Peninsular Malaysia. Despite the successful application of the GPT-4 with Noteable plugin, certain limitations and challenges are identified, highlighting the necessity for further validation of the tool's applicability and limitations. This study encourages future research to (1) adopt the proposed framework in other regions, (2) explore more detailed analyses encompassing all variables, and (3) leverage machine learning for advanced forecasting.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Many farms are replacing the lighting with light emitting diode (LED) bulbs because of the technological modernization. We aimed to investigate the effects of incandescent light (IL) and LED lighting on Cobb500 broiler chickens for six weeks. Production parameters (body weight, feed consumption, feed conversion ratio), calculated slaughter values (yield%, relative breast%, thigh%) and breast meat quality parameters (pH at 45 min and 24 h postmortem, color, drip loss, kitchen equipment losses, shear force, meat composition) were recorded. Non-stop recordings were used to analyze the behavior of the birds in several periods of the rearing. LED group was significantly better in body weigh parameter between week 1-5 and feed conversion ratio between week 2-3. The most significant difference in behavior was observed in the middle of the rearing period. The chickens in the LED group spent more eating time, drinking time, interacting, and resting less. There was no difference in the meat quality parameters, only shear force was significantly lower in the LED group (1781.95±0.33 g/s vs. 2098.82±0.42 g/s). Based on our results, LED lighting can bring positive changes in animal production efficiency, behavior, and important characteristics for meat consumers.

In our study, we assessed the effects of verbenone, the most widely studied bark beetle aggregation inhibitor, on saproxylic beetles of a Mediterranean pine forest in Tuscany. Verbenone pouches were devised in the laboratory and then applied to Ips sexdentatus pheromone traps so that catches could be compared to those of traps with just the bait. The trial was carried out in spring-summer 2023, collecting insect catches every two weeks. A total of 9440 beetles were collected, belonging to 32 different families and 57 species. About 80% of captures were bark beetles, mainly Orthotomicus erosus. Beetle predators accounted for about 17% of the captures, with a total of 12 species. Some of these predator species had never been studied yet in relation to verbenone effects, like other saproxylic beetles recorded in this study. A significant reduction of captures was recorded for some beetles (e.g. I. sexdentatus and O. erosus), for other species no differences emerged, and in some cases captures increased significantly when verbenone was present in the traps (i.e.. Hylurgus ligniperda, Corticeus pini, Aulonium ruficorne). The diversity of caught saproxylic beetles increased significantly in verbenone traps, highlighting possible implications of the use of verbenone when managing bark beetle outbreaks.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil & gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

Under the development mode of deep blending of emerging technologies, major projects are important for enhancing China's comprehensive national strength and independent innovation capability. Based on the social benefits of major projects, and considering the influence of reputation factors, an evolutionary game model composed of a general contractor and subcontractor of major projects is established. This paper studies the influence of various factors including the income distribution coefficient of collaborative innovation, and MATLAB simulation software is analyzed the influence of factors on an evolutionary path. The results show that a reasonable income distribution coefficient can promote the game behavior of both parties to the direction of active collaborative innovation; The reduction of innovation cost and the improvement of spillover technology absorption capacity can make innovation subjects tend to choose active collaborative innovation strategies. In addition, reputation loss above a specific threshold can effectively inhibit free-riding behavior and encourage innovation subjects to choose active collaborative innovation strategies. The research results provide reference for promoting major projects' technology innovation.

The use of salt rock for underground radioactive waste disposal facilities requires a comprehensive analysis of creep-damage process in salt rock. A computer-controlled creep setup is employed to carry out a creep test of salt rock lasted as long as 359 days under a constant uniaxial stress. The AE space-time evolution and energy releasing characteristics during creep test are studied in the meantime. A new creep-damage model is proposed on the basis of fractional derivative by combining the AE statistical regularity. It indicates that the AE data in non-decay creep process of salt rock can be divided into three stages. Furthermore, the parameters of new creep-damage model are determined by Quasi-Newton method. The fitting analysis suggests that the creep-damage model based on fractional derivative in this paper provides a precise description of full creep regions in salt rock.

Synthetic materials such as Carbon, Kevlar, and Glass fibers are extensively utilized in various industries due to their superior characteristics including high stiffness, great strength, low den-sity, and high wear resistance, these advantages contributed to making them widespread in ap-plications like; aerospace, automobile, civil and electronics. This research is carried out to enhance the creep compliance of epoxy composite material by considering two types of fibers as reinforcement. A composite material is produced by combining two fibers, Kevlar fiber mixed with sika epoxy resin, along with Carbon fiber also mixed with sika epoxy resin using a Hand-Layup process. Experiments and numerical modeling are examined to offer a comprehensive understanding creep behavior of epoxy composite material in different weight ratios. Burger and Prony models are used to represent stress relaxation and creep strain of Visco-elastic material. According to the results, sika epoxy resin reinforced with Kevlar and Carbon fibers exhibits enhancement in the mechanical properties compared with pure epoxy. The use of Kev-lar/Sika epoxy composite results in higher creep compliance and modulus of elasticity compared with Carbon/Sika epoxy composite.

This paper discusses recent developments in creep, over a wide range of temperature, that mqy change our understanding of creep. The five-power law creep exponent (3.5 to 7) has never been explained in fundamental terms. The best the scientific community has done is to develop a natural three power-law creep equation that falls short of rationalizing the higher stress exponents that are typically five. This inability has persisted for many decades. Computational work examining the stress-dependence of the climb rate of edge dislocations we may rationalize the phenomenological creep equations. Harper-Dorn creep, “discovered” over 60 years ago has been immersed in controversy. Some investigators have insisted that a stress exponent of one is reasonable. Others believe that the observation of a stress exponent of one is a consequence of dislocation network frustration. Others believe the stress exponent is artificial due to the inclusion of restoration mechanisms such as dynamic recrystallization or grain growth that is not of any consequence in the five power-law regime. Also, the experiments in the Harper-Dorn regime, which accumulate strain very slowly (sometimes over a year) may not have attained a true steady state. New theories suggest that absence or presence of Harper-Dorn may be a consequence of the initial dislocation density. Novel experimental work suggests that power-law breakdown may be a consequence of a supersaturation of vacancies which increase self-diffusion.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

This paper addresses the effect of both microstructure and relative humidity on the long-term creep properties of sustainable calcium carbonate (CaCO₃) cements. Those can be prepared by mixing amorphous calcium carbonate and vaterite with water. A larger starting amount of vaterite, X_V, within the mixture design gives a higher elasticity and resistance to the specimens due to the larger overall bridging area within the newly formed calcite crystals. Regarding creep properties for a given relative humidity, the amplitude of creep strain decreases with X_V, and makes the relation between the elastic modulus, E, and hardness, H, of the samples to be linear with the contact creep modulus, C. On the other hand, for a given composition, the amplitude of creep increases with the relative humidity, making the contact creep modulus, Ci, to rise exponentially with the elastic modulus, E, and hardness, H, of the specimens. The most probable creep mechanisms for this kind of cement seem to be a combination of microcraking in the early stages and dissolution and reprecipitation of calcite in the long-term (also known as pressure solution theory). The presence of water in pores with increasing relative humidity might enhance the local dissolution of calcite, and hence the creep amplitude.

Creep deformation behaviour in single phase γ-TiAl alloy has been an extensively studied topic since the late 1970s. A lot of literatures have reported creep behaviour of γ-TiAl alloys, manufactured using different processing techniques [1]–[7]. The present discussion revisits the original work on understanding the tensile creep deformation behaviour of wrought single-phase γ-TiAl alloy by Hayes et al. [8] and is aimed to develop an understanding of steady state creep, through strain vs strain rate and strain vs ln(strain rate) plots. Besides, it also attempts to study the variation of stress exponent with temperature between 760-900⁰C and also, to determine activation energies using the two most common approaches, namely: Zener-Hollomon (Z-H) [9] and Sherby-Dorn (S-D, temperature compensated time approach) [10] for stress levels of 69 and 103.4 MPa between 760-900⁰C.

Leaf springs are critical components for the railway vehicle safety in which they are installed. Although these components are produced in high-strength alloyed steel and designed to operate under cyclic loading conditions in the high-cyclic fatigue region, their failure is still possible to occur and hence lead to economic and human catastrophes. The aim of this document is precisely to characterise the mechanical crack growth behaviour of the 51CrV4 spring steel representative of leaf springs under cyclic conditions, that is, crack propagation in mode I. The common fatigue crack growth prediction models (Paris and Walker) considering the effect of stress ratio and parameters such as propagation threshold, critical stress intensity factor and crack closure ratio are also determined using statistical methods, which resulted in good approximations with respect to the experimental results. Lastly, the fracture surfaces under the different test conditions were analysed using SEM, with no significant differences to declare. As a result of this research work, it is expected that the developed properties and fatigue crack growth prediction models can assist design and maintenance engineers in understanding fatigue behaviour in the initiation and propagation phase of cracks in leaf springs for railway freight wagons.

This contribution addresses dry sliding friction of a “Non-Asbestos Organic” friction material (pad) rubbed against a pearlitic grey cast iron disc. This configuration is commonly used in brakes in US, Europe and Asia. The initial stage of friction is of particular interest when addressing “creep-groan” phenomena occurring in passenger and sport utility vehicles with automatic transmissions. The custom built Universal Friction Tester allowing the variation of sliding speed, test temperature, normal load, stiffness and humidity of the system was used in this experiment in combination with surface analysis by polarized light microscopy, scanning electron microscopy and stylus profilometry. The obtained results indicate that the “stick” phase in the so-called “stick-slip” phenomenon does not really exist. The surfaces of pad and disc are in continuous relative movement. The complexity of surfaces does not allow for a definitive description of exact mechanisms responsible for the detected changes of friction forces. The observed friction process can be rather described as a stretching with possible localized relaxations causing the jerky behavior in the stretching phase, followed by slip between two materials in contact. Understanding of factors contributing to the stretching at different scale levels of friction system is necessary for development of proper models. An accurate friction model should also incorporate the vibrational element introduced by phenomena occurring at the friction surfaces. The absence of heterogeneous regions on the friction surface and “evenly distributed friction level” can help when mitigating creep-groan in the investigated brake system. Understanding of factors on different scales of friction is also required when developing the improved brakes.

The creep behaviors of TA2 and R60702 at low and intermediate temperature were presented and discussed in this paper. Experimental results indicated that an apparent threshold stress exhibited in the creep deformation of R60702. Meanwhile, the primary creep phase was found as the main pattern in the room temperature creep behavior of TA2. Compared with exponential law, the power law has been proved to be a proper constitutive model in the description of primary creep phase. It also showed that θ projection method had its significant advantage in the evaluation of accelerated creep stage. Thus, a composite model which combined power law with θ projection method was applied in the creep curves evaluation at low and intermediate temperature. Based on the multiaxial creep deformation results, the model was modified and discussed. A linear relationship existed between composite model parameters and applied load. Finally, the creep life could be accurately predicted and the composite model method is suitable for application in low and intermediate temperature creep life analysis.

According to previous studies the median raphe region (MRR) is known to contribute significantly to social behavior. Beside serotonin, there are reports of a small population of dopaminergic neu-rons in this region. Dopamine is linked to reward and locomotion, but very little has been known about its role in the MRR. To address that, we first confirmed the presence of dopaminergic cells in the MRR of mice (immunohistochemistry, RT-PCR) and humans (RT-PCR). Next, we used chemogenetic technology in mice containing Cre enzyme under the promoter of the dopamine transporter (DAT). With the help of an adeno-associated virus, artificial receptors were expressed in the dopaminergic cells of the MRR (DAT-MRR). Four weeks later, extensive behavioral charac-terization started 30 minutes after the injection of the artificial ligand (Clozapine-N-Oxide). Stimu-lation of DAT-MRR decreased social interest without influencing aggression and with an increase in social discrimination. Additionally, inhibition of the same cells increased the friendly social be-havior during social interaction test. No behavioral changes were detected in anxiety, memory and locomotion. All in all, dopaminergic cells were present both in the mice and human MRR, and manipulation of dopaminergic neurons of the MRR elicited a specific social response.

Due to the continued deepening of today’s mining projects, there is a need to develop new or improved rockbolts that are strong and yielding and have high energy absorption when exposed to dynamic loading. Impact tests can provide useful information about the dynamic response of rockbolts but most laboratory tests involve high costs in preparation and result validation. Numerical modeling is an alternative that, in addition to complementing laboratory results, can be used to represent the process of deformation and energy absorption of support elements. In this paper the implementation and results obtained from a finite difference (FDM) numerical model are presented. The model functions as a simulation tool to illuminate all the elements that conform the large-scale (1:1) impact test and their behavior and influence on the dynamic response of a threadbar bolt (22 mm nominal diameter). The model was calibrated using published results and based on these results as well as parametric analysis, the response of each component (steel tube, grout, and bolt) could be identified and its behavior in terms of absorbed energy and displacement could be observed. Results show the model can provide important preliminary information to make design decisions about support elements design.

Taeniid infections pose a significant threat to both animal and public health, as certain tapeworms within this group can also infect humans, potentially leading to severe health conditions. Therefore, this calls for preventive and control measures, such as regular deworming of dogs. While the efficacy of deworming has been established in developed countries, there is a paucity of reported deworming practices in rural areas of developing countries, such as Tanzania. This study aims to understand determinants for helminth treatment-seeking behavior towards control of cestodial taeniid infections in rural settings in northern Tanzania. A cross-sectional study was undertaken in agropastoral and pastoral areas of northern Tanzania. Comprehensive data from household surveys in selected sub-villages were collected to ascertain dog ownership, dog deworming practices, and the availability of dewormers. Analytical methods were employed to discern how various determinants influenced deworming practices among dog owners in these communities. Awareness of dewormers specifically formulated for dogs emerged as a pivotal factor affecting dog deworming practices. Dog owners who were informed about appropriate dog dewormers were nearly two times more likely to engage in deworming compared to those with limited knowledge (OR = 1.78, 95% CI 1.77 - 4.18, p < 0.001). A majority 32(51.6%, 95% CI: 38.7-64.3) acknowledged accessing dewormers for livestock within their wards. Praziquantel a potent dewormer on cestodes was least known to most dog owners 2(13%, 95% CI: 2.3-41.6). Praziquantel, a potent and common dewormer effective against cestodial taeniid infections, remains relatively unknown in rural areas of northern Tanzania. Therefore, more awareness on appropriate deworming agents against taeniids in dogs should be raised in rural dog-keeping communities.

It has been known for nearly over 150 years that fatigue life data exhibits a considerable amount of variability. Furthermore, statistically modeling fatigue life adequately is challenging. Different empirical approaches have been used, each of which has merit; however, none is appropriate universally. Even when a sufficiently robust database exists, the scatter in the fatigue lives may be extremely large and difficult to characterize. The complications in empirical modeling are exacerbated for long life estimation when experimental observations are rare. The purpose of this work is to review traditional and more modern empirically based methodologies for estimating the cumulative distribution functions for fatigue life, given an applied load. To assess the applicability of the methods confidence bounds will be estimated. The analyses will be performed on an historic set of data for annealed aluminum wire tested in reverse torsion fatigue. These data are available in publications. It is recommended that a time dependent distribution function that is an based on principles of reliability that can be generalized for a variety of modeling applications should be considered for fatigue life estimation.

Alloy 800H stands as one of the few code qualified materials for fabricating in core and out of core components operating in high temperature reactors (HTRs). Welding is a common practice for assembling these components, however, the election of a suitable filler material is essential to enhance the high-temperature creep resistance of Alloy 800H weldments in high temperature applications. In this study, Inconel 625 and Haynes 230 filler material were used to weld the Alloy 800H plates employing the Gas Tungsten Arc Welding (GTAW) technique. The high temperature tensile, creep rupture property, microstructural stability and evolution of the weldments after high temperature exposure were investigated and compared with Alloy 800H. The results showed that the both weldments exhibited enhanced tensile and creep behavior at 760 oC. The creep rupture time of the weldments with Inconel 625 filler and Haynes 230 filler materials was about two and three time longer than that of Alloy 800H base metal when tested at 80 MPa and 760 oC, respectively. Carbides (MC and M23C6) were commonly observed in the microstructure of both the weld and base metals in the two weldments after high temperature creep tests. However, the Inconel 625 filler weldment displayed detrimental δ and Laves phase in the fusion zone and these precipitates could be potential sites for initiating cracks following prolonged high temperature exposure. The study showed that the weldment with Haynes 230 exhibited better phase stability and creep rupture property than the one with Inconel 625 filler material, suggesting its potential as a candidate filler material for Alloy 800H for further investigation. The finding also emphasizes the critical consideration of microstructural evolutions and phase stability in evaluating high temperature materials and their weldments in high temperature reactor applications.

The process involved in preparing driving simulator tests is a labor intensive one, and the nature of this complexity depends on the sophistication of the tests to be carried out, as well as the number of participants. Which has an impact on the duration of the research itself. The very solution of using driving simulators is a research tool that has been in use for many years and with great success. They are used in a very wide range of areas of human functioning. They replicate in a very realistic way the conditions that can occur in the external environment, offer the possibility of repetition of particular conditions and insight into certain behaviors that could be very difficult to initiate in real life. This article also describes the dis- ease of using simulators to conduct research activities, along with the workflow from assumptions to finalizing the research. An algorithm is also presented for the study of individual participants, with examples for separate research scenarios concerning driver behavior in the vicinity of pedestrian crossings.

This article reports on the comparative study of the hot deformation behaviour of virgin (steel A) and rejuvenated heat treatment creep-exhausted (steel B) P91 steels. Hot uniaxial compression tests were conducted on the two steels at the deformation temperature range of 900°C-1050°C and a strain rate range of 0.01-10s-1 to 0.6 strain using Gleeble® 3500 equipment. The results showed that the flow stress largely depends on the deformation conditions. The flow stress for the two steels increased with an increase in strain rate at a given deformation temperature and vice versa. The flow stress-strain curves exhibited a dynamic recovery as the softening mechanism. The material constants determined using Arrhenius constitutive equations were: stress exponent was: steel A (5.76) and steel B (6.67), and the apparent activation energy was: steel A (473.1 kJ mol-1) and steel B (564.5 kJmol-1). From these results, steel A exhibited better workability than steel B. Statistical parameters analyses showed that the flow stress for the two steels had a good correlation between the experimental and predicted data. Pearson’s correlation coefficient (R) was: steel A (0.97) and steel B (0.98). The Average Absolute Relative Error (AARE) values were: 7.62% (steel A) and 6.54% (steel B). The study shows that the Arrhenius equations can effectively describe the flow stress behaviour of P91 steel, and this method is applicable to the industrial metalworking process.

Background: Autism spectrum disorder (ASD) is a persistent neurodevelopment disorder frequently co-occurring with Attention-Deficit/Hyperactivity Disorder (ADHD) and behavior-related disorders. While behavioral therapy is the first-line option to manage ASD core symptoms, pharmacological therapy is sometimes needed to treat acute problems, such as agitation and aggressive behaviors. Recent guidelines recommend neuroleptics to reduce psychomotor agitation in people with ASD. However, since children with ASD are often drug-resistant, alternative treatments are often justified. Reports from literature showed that intra-venous valproate (IV-VPA) can be effective in reducing agitation in psychiatric patients, with lower frequency of adverse events compared to convention-al treatments. However, since findings are occasionally inconsistent, IV-VPA is not an approved option in clinical psychiatry. We aim at improving the knowledge on the IV-VPA treatment option in emergency psychiatry in the pediatric age. Methods: We report the case of a 11-year-old boy suffering from a complex neurodevelopmental condition, who experienced a psychotic episode with severe aggressive and disruptive behaviors, successfully treated with IV-VPA. Besides, we conducted an up-dated literature review on this topic. Conclusion: In our case, first-line therapies proved to be ineffective. On the contrary, IV-VPA led to a safe and prompt clinical success, in line with other reports. Based on our literature review, IV-VPA can be highly effective and can reduce the risk of adverse events that frequently occur with the use of high-dose standard medications in emergency psychiatry.

The concept of Design Fatigue Factors (DFFs) was introduced for providing desired level of safety in structural fatigue design, often associated with damage calculated from S-N curves. Calculation of fatigue damage from S-N curves can be affected by multiple factors, e.g. types of weld class, corrosion condition, loading conditions, stress concentration on different geometries etc. Each of them can be subject to different level of uncertainties. This study intends to recalibrate the DFFs from a detailed reliability analysis by investigating the probabilistic models derived from the database of S-N curves that has been most frequently used in offshore wind industry. The results of such study indicate that the DFFs can be reduced substantially for the corrosive environmental fatigue models from current standards to the same level of target reliability.

This paper studies the flexural behavior of the bridge deck link slabs made with the Polyvinyl Alcohol-Strain Hardening Cementitious Composites (PVA-SHCC). Tensile and flexural properties of the PVA-SHCC with four volume fractions, i.e., 0%, 1%, 1.5%, and 2%, were evaluated first. Next, using the similarity theory, composite models with a geometric similarity ratio of 1: 5 were designed to represent the bridge deck with the link slabs. The models considered three materials for link slabs, including concrete, cement mortar and self-compacting PVA-SHCC; and two different curing ages at 7 and 56 days. Bending tests were performed to investigate the flexural behavior of the models. Based on the fractal theory, cracking characteristics of the models with different types of link slabs were compared, and the relationship between Df and the flexural behavior of the models were studied. Numerical models were built to correlate with the results from the bending tests. It is illustrated that the flexural behavior of the self-compacting PVA-SHCC link slab is better than that of concrete and cement mortar link slabs, where the crack initiation and propagation can be postponed.

In 2011, it was reviewed that there is a strong co-occurrence between major depression and chronic fatigue syndrome (CFS), with fatigue and physio-somatic symptoms being key symptoms of depression, and depressive symptoms appearing during the course of CFS. Moreover, the comorbidity between both conditions may in part be explained by activated immune-inflammatory pathways, including increased translocation of Gram-negative bacteria and increased levels of pro-inflammatory cytokines, such as interleukin (IL)-1. Nevertheless, the possible involvement of activated microglia in this comorbidity has remained unclear. This paper aims to review microglial disturbances in major depression, CFS and their comorbidity. A comprehensive literature search was conducted using the PubMed / MEDLINE database to identify studies that are relevant to this current review. Depressed patients present neuroinflammatory alterations, probably related to microglial activation, while animal models show that a microglial response to immune challenges including lipopolysaccharides is accompanied by depressive-like behaviors. Recent evidence from preclinical studies indicate that activated microglia have a key role in the onset of fatigue. In chronic inflammatory conditions, such as infections and senescence, microglia orchestrate an inflammatory microenvironment thereby causing fatigue. In conclusion, based on our review we may posit that shared immune-inflammatory pathways and activated microglia underpin comorbid depression and CFS and that activated microglia are the main orchestrators of this comorbidity. As such, microglial activation and neuro-inflammation may be promising targets to treat the overlapping manifestations of both depression and CFS.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

A problem of efficacy of crystal growth methods for crystallization from solution or melt has been investigated. Axial vibrational control (AVC) technique was considered as a perspective method to manage both heat-mass transfer and chemical component composition of the melts in the case of crystallization of complex chemical compounds. Numerical modeling and the search for generalized dependencies made it possible to predict the AVC parameters that provide optimal heat and mass transfer modes for creating flat liquid-solid interfaces, as well as the component composition of dissociated melts of various chemical compounds – Ge, NaNO3, CdTe.

Present work has systematically investigated the evolution of dispersoid and elevated-temperature properties including the strength and creep resistance during the various multi-step heat treatments in Al-Mn-Mg 3004 alloys. Results show that only α-Al(MnFe)Si dispersoid is observed in the studied temperature range (up to 625°C) and it coarsens with increasing temperature to 500°C but dissolves at 625°C. The evolution of elevated-temperature strength and creep resistance is greatly related to the temperature of each step during the multi-step heat treatments. Generally, lower temperature at the first-step heat treatment leads to higher properties while the properties decrease with increasing temperature of last-step heat treatment. Suitable models have been introduced to explain the evolution of strength and the creep threshold stress at elevated-temperature during the various heat treatments.

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

Recent works in mechanical fatigue consider that a threshold of entropy exists, the fracture fatigue entropy. The determination of this quantity is usually done considering empirical models for the mechanical power estimation. In this paper, we experimentally observe the existence of a threshold of entropy and exergy in low cycle fatigue for a flat Al-2024 specimen avoiding the use of a model, solely measuring the heat generated during a fatigue test. Results are then compared considering various hypotheses (1D heat dissipation with convection and radiation considered as heat sources, and, heat transfer from a fin with convection and radiation as boundary conditions) to an empirical mechanical model known in the literature and deviations between them are discussed.

Athletes are exposed to high-intensity loads to promote athletic performance, however without appropriate evaluation for its effects. This study investigates the effects of four types of exhaustion exercises on Heart Rate Variability (HRV) and Poincaré features as markers of central fatigue; Creatine Kinase (CK) and blood lactate concentrations ([LA-]b) as biomarkers of peripheral fatigue. To achieve this purpose, ten healthy volunteers were exposed to exhaustive exercise using isotonic-, isometric-, aerobic-, and anaerobic-fatigue protocols. HRV Poincaré features, standard deviation of instantaneous beat-to-beat R-R interval variability (SD1) and standard deviation of continuous long-term R-R interval variability (SD2) variables were collected. Central fatigue was tested through the sympathetic stress index (SS) and the sympathetic and parasympathetic index (SS/SD1). Blood samples were collected at the beginning and at the end of the exercises to determine CK and [LA-]b. The SD1 decreased in each exercise protocol, while the SS and SS/SD1 increased. [LA-]b and CK increased at the end of each protocol and correlated with SD1 and SS/SD1. HRV, CK, and [LA^-]_b are acute markers to detect, both central and peripheral fatigue; sensitive to the type, duration, and intensity of exercise, being HRV a novel noninvasive marker, simple and useful for sports coaches and athletes.

TThe aim of the work is to present a newly developed stand and methodology of accelerated tests of fatigue strength of flexible propellers and fins. The paper presents the design and concepts of the measuring elements used in the research. Test methodology and water stressing were devel-oped. The mechanical properties of the following materials were presented: Arnitel EL-550 and QUEO 8230 with the addition of PP / EVA 50/50 (polypropylene / ethylene-vinyl acetate) - in the proportion of 70/30 (QUEO 8230 / additive). The constructed test stand and a new method of fa-tigue testing of biomimetic fins made it possible to determine the number of fin movement cy-cles under a given load, which may facilitate the determination of a warranty for a newly intro-duced product. The current consumption by the fin drive and video monitoring allowed for the selection of the range of the number of movement cycles and the determination of the moment of fatigue cracks until the fin structure loses its capacity. During the analysis, the test results showed that the fins made of Arnitel EL-550 did not show changes in the measured values of the current and the force generated by the fin. For a fin made of QUEO 8230, at 35,000 cycles, there is a decrease in the current and force consumed, which indicates the initiation of fatigue damage to the fin. The performed tests can be the basis for the development of standards for the fatigue strength of flexible propellers.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

The creep response of commercially pure titanium was investigated in air at 550, 600 and 650°C, to assess the effect of oxidation on the mechanical response. Experiments demonstrated that exposure at high temperature produced a marked reduction of the minimum creep rate under a given applied stress. Microhardness measurements showed that a hardened zone forms in proximity of the surface, due to oxygen penetration into metal. A simplified composite-model was then used to describe the creep response. In this model, the sample consisted of two zones, the hard case, enriched in oxygen, and the soft pure-titanium core, both creeping with similar strain rates. Calculation led to an estimation of the dependence of the minimum creep rate on stress and temperature for the hard high-oxygen zone. The simplified composite-model here presented gave an excellent description of experimental creep data for pure titanium tested in air and also provided a reliable picture of the effect of oxidation on complex Ti-alloys.

Human Papillomavirus (HPV) self-sampling has the potential to increase cervical cancer screening (CCS) and reduce the cervical cancer burden in Medically Underserved Women (MUW). However, interventions promoting self-sampling are limited. We examined the effectiveness of an intervention study in increasing CCS among MUW. We conducted a quasi-experimental intervention study. Face-to-face verbal approach was to recruit MUW (n=85, mean age 48.57±11.02) living in a small city in the US. Behavioral intervention based on reframing, reprioritizing, and reforming (3R model) was used to educate the women about CCS in a group format. The women completed pre-and post-intervention assessments and followed-up interviews. The primary outcome was CCS uptake. Mixed methods analyses were conducted using a t-test for the primary outcome, PROCESS for mediation analysis, and NVivo for interview data. Majority of women (75%) completed self-testing. High-risk HPV prevalent among the women was 11%, and of those, 57% followed-up with physicians for care. We found that the significant increase in the women’s post-intervention screening behaviors was mediated by the increase in knowledge (Indirect Effect [IE] = .1314; 95% CI, .0104, .4079) and attitude (IE = .2167; 95% CI, .0291, .6050) scores, (p&lt;0.001). Interview analyses offered further explanations (see the explanations in parenthesis) why MUW found the intervention messages acceptable (encourages proactive behavior), feasible (simple and easy to understand), and appropriate (helpful and informative). Barriers including lack of trust and fear of results were identified. The findings suggest that an intervention that combines the 3R model and self-sampling may increase CCS among MUW.

Development of accelerometer-based lameness (mobility) detection has focused on cow behaviors such as lying and walking. Several studies, usually small, have reported levels of accuracy up to 91%. However, there has been limited independent replication of these results. In this study, behavior measures previously identified as being associated with lameness such as lying bouts and walking time are examined in relation to mobility score. On a research farm and a commercial farm, four trials were completed with 65 grazing cows. The cows had differing mobility scores ranging from perfect mobility to impaired mobility. Behavior was monitored using leg worn accelerometers. In general, behavior and mobility associations identified in previous studies were not found. Behavior monitoring with accelerometers as a basis to classify impaired mobility in pasture-based contexts thus remains challenging.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

In this paper, we present a new stress calculation method for flexible structures, particularly, the tensile armors, and apply it to flexible riser fatigue analysis. The method is based on a 3-dimensional curved bar theory. First, the tensile armor center line was described as a cylindrical helix curve, its bended curve length and bending migration length were derived and studied under different friction scenarios. Second, the tensile and bending stiffness was given with consideration of frictional hysteretic effect, and verified through FEA analysis results. Third, we presented the stress calculation formula for tensile armor under tension and bending load. All stress components are considered, including tensile, bending and shear stresses. Fourth, the method was benchmarked with published experimental results on a flexible prototype tension and bending tests, and comparisons showed general agreements. Fifth, the method is further applied to a 8” flexible riser for fatigue assessment and lifetime extension evaluation, and showed the flexible riser has sufficient remaining fatigue life, and is suitable to continue its service under the current operating conditions. Last, conclusions are drawn. It concluded that the presented tensile armor stress calculation method and modelling techniques are valid for flexible riser fatigue analysis. This method is time efficient, and can be implemented into other multi-scale models for riser dynamic analysis. It is also applicable to other similar helix structure stress analysis, such as wire ropes, submarine hoses, and subsea umbilicals.

Natural cellulose hydrogels have been widely used to enhance mechanical properties. However, existing natural fiber composite hydrogels are not reusable, limiting their potential applications. To address this issue, we designed and prepared a polyvinyl alcohol/glycerol /bamboo microfibril double network tough hydrogel using a simple method. The bamboo microfibril and polyvinyl alcohol form a tight and rigid network through hydrogen bonding, improving mechanical properties. The prepared polyvinyl alcohol/glycerol/bamboo microfibril double network tough hydrogel has the advantages of reusability and fatigue resistance. Furthermore, both the elastic modulus and toughness of the hydrogel increase with increasing bamboo microfibril content. We also demonstrated that the hydrogel can be recast after cyclic compression, maintaining its recyclability, stability, and certain stiffness and toughness. Our study highlights the potential of hydrogels for controllable mechanical properties, fatigue resistance and shows that polyvinyl alcohol/glycerol/bamboo microfibril hydrogel has broad value for plasticity and reuse.

This paper aims to provide an overall review of degradation, damage evolution and fatigue models in the literature of various engineering materials, mostly metals, and composites.

Reliable fatigue design rules affect the proactive identification of safety parameters in aerospace industry. Numerous fatigue crack initiation and propagation models, linear and nonlinear, have been developed for designing purposes or estimation of the remaining life of aging airplanes. Depending on the adopted assumptions, the accuracy varies for different loading histories, loading types, and materials. Semi empirical models are simple but yield significant inaccuracies. Models with better theoretical basis provide better accuracy, but implementation in real conditions is problematic. In the present work, a review of author’s recent fatigue crack initiation and propagation models based on physical mechanisms is presented and improvements are proposed. Verification of the models on test results is provided and discussed.

In Nature, it is common for living plants and non-living plant tissues to consist of materials with anisotropic multilayer and non-homogenous structure. The structure of tissues determines their self-shaping and self-folding capabilities in response to a stimulus in order to activate different functionalities. Predetermined movements are realized according to changes in environmental conditions, which trigger the fibrous anisotropic structure of the plants’ material. In this study, we present the fabrication process of low-cost anisotropic multilayer materials that are capable of realizing complex movements caused by small temperature changes (<40 ^oC). The mismatch in the thermo-mechanical properties between three or more anisotropic thin layers creates responsive materials that alter their shape owing to the developed internal stresses. Isotropic layers can perform only bending movements, whereas anisotropic multilayer materials can perform bending, twisting or complex combined modes. The movements of the material can be controlled by forming anisotropic homogenous metallic strips over an anisotropic polymer. As a result, inexpensive responsive materials can be developed to passively react to a very broad range of thermal requirements. We studied the major parameters that affect the sensitivity of the developed materials, as well as their failure modes and crack formation under thermal fatigue conditions.

The orexin/hypocretin neuropeptide family has emerged as a focal point of neuroscientific research following the discovery that this family plays a crucial role in a variety of physiological and behavioral processes. These neuropeptides serve as powerful neuromodulators, intricately shaping autonomic, endocrine, and behavioral responses across species. Notably, they serve as master regulators of vigilance and stress responses; however, their role in complex processes such as food intake, metabolism, and thermoregulation warrant further investigation. This narrative review provides a journey through the evolution of our understanding of the orexin system, from its initial discovery to the promising progress made in developing orexin derivatives. It goes beyond conventional boundaries, striving to synthesize the multifaceted activities of orexins. Special emphasis is placed on domains such as stress response, fear, anxiety, and learning, in which the authors contributed to the literature with original publications. This article demonstrates the orchestrating role of the orexins in several intricate and integrative physiological processes. It also overviews the advancement of orexin pharmacology, which has already yielded some promising successes, particularly in the treatment of sleep disorders. This interdisciplinary approach to studying neuropeptides unveils their significance as vital connectors between transient functional changes and lasting structural adaptations. Ultimately, it advances our understanding of the intricate physiological and behavioral contributions of the orexin/hypocretin neuropeptide family.

Some wind farms have implemented automated camera\textendash based monitoring systems e.g. IdentiFlight to mitigate the impact of wind turbines on protected raptors. These systems have effectuated the collection of large amounts of data that can be used to describe flight behavior in a novel way. This data uniquely provides both flight trajectories and images of individual birds throughout their flight trajectories. The aim of this study was to evaluate how this unique data could be used to create a robust quantitative behavioral analysis, that could be used to identify risk prone flight behavior and avoidance behavior thereby in the future assess collision risk. This was attained through a case study at a wind farm on the Swedish island Gotland, where golden eagles (Aquila chrysaetos), white-tailed eagles (Haliaeetus albicilla), and red kites (Milvus milvus), were chosen as the selected bird species. The results demonstrate that flight trajectories and bird images can be used to identify high risk flight behavior and thereby also used to evaluate collision risk and avoidance behavior. This study presents a promising framework for future research, demonstrating how data from camera\textendash based monitoring systems can be utilized to quantitatively describe risk prone behavior and thereby assess collision risk and avoidance behavior.

The plate heat exchanger (PHE) is a component that provides heat to be transferred from hot water to domestic cold water without mixing them with high efficiency. Over the lifetime of the PHE, cyclic pressures act on the brazing points and the plates, and this may lead to fatigue failure. The fatigue behaviour of the PHE, designed by using copper-brazed 316L stainless steel, was investigated in this study. First, the fatigue tests under the load ratio R = 0.1 were performed on the Vibrophore 100 testing machine to obtain the S-N curve of the analysed brazed joint. Based on the obtained experimental results, an appropriate material model of the analysed brazed joint has been created, which was validated with numerical calculation in the framework of a program code Ansys. A validated material model was then used for the subsequent numerical analysis of PHE. In order to carry out a numerical calculation using the finite element method (FEM), a 3D model of the heat exchanger was created based on the previous scanning of PHE-geometry. Thereafter, the geometry was parameterised, which allowed us to perform parametric simulations (monitoring different responses depending on the input geometry). Numerical simulations were carried out in the framework of the Ansys software, whereby the obtained results were analysed, and the responses were appropriately characterised according to previously determined load cases.

The underlying molecular basis of Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is not well understood. Characterized by chronic, unexplained fatigue, a disabling payback following exertion (“post-exertional malaise”) and variably presenting, multi-system symptoms, ME/CFS is a complex disease which demands concerted biomedical investigation from disparate fields of expertise. ME/CFS research and patient treatment have been challenged by the lack of diagnostic biomarkers and finding these is a prominent direction of current work. Despite these challenges, modern research demonstrates a tangible biomedical basis for the disorder across many body systems. This evidence is largely comprised of disturbances to immunological and inflammatory pathways, autonomic and neurologic systems, abnormalities in muscle and mitochondrial function, shifts in metabolism, and gut physiology or gut microbiome disturbances. It is possible that these threads are together entangled as parts of an underlying molecular pathology reflecting a far-reaching homeostatic shift affecting each of these systems. Due to the variability of non-overlapping symptom presentation or precipitating events such as infection or other bodily stresses, the initiation of body-wide pathological cascades with similar outcomes stemming from different causes may be implicated in the condition. Patient stratification to account for this heterogeneity is therefore one important consideration during exploration of potential diagnostic developments.

Abstract Background Fatigue Syndrome (FS) is described as extreme exhaustion following ordinary activities. Sleep deprivation, the use of antidepressants, autoimmune illnesses, and anemia are also risk factors for FS. Symptoms of FS include headache, dizziness, and dyspnea, among others. Objective: This study focused on assessing the prevalence of fatigue syndrome (FS) and its association with depression and anxiety, among the medical students in Saudi Arabia. Methodology In this cross-sectional investigation conducted in 2023, 740 medical students participated. Data were gathered using an online survey, which encompassed four key sections: Sociodemographic details, the 11-item Chalder Fatigue Questionnaire (CFQ), the 9-item Primary Health Questionnaire (PHQ) assessing depression, and the Generalized Anxiety Disorder 7-item (GAD-7) scale. Analyses were performed by the use of SPSS version 25. Results A total of 740 students were surveyed, 417 (56.4%) satisfied the diagnostic requirements for fatigue syndrome (FS), with most of them being females. Furthermore, 234 (31.2%) and 296 (40.8%) of the participants reported having significant anxiety symptoms and depressive symptoms, respectively. FS was positively correlated with symptoms of anxiety and depression (P

Chronic Fatigue Syndrome (CFS) can be triggered by different factors and create a complex health situation. In the last decades incidence has been increasing. This situation is a clear example of how humans, viruses, and the environment are all connected. In the 90s cases related to CFS, com-plaints about a feeling of chronic fatigue, inability for everyday tasks, dull pain, cephalalgia, de-pression, anxiety, poor concentration. Clinical tests for EBV, HHV, CMV, IgG, IgM, T4 and T8 subsets were tested, along with hormones and hemogram tests. Most of the cases were women. The timeline of the medical history showed also myomas, breast lumps, premenstrual syndrome previously to CFS development. The nature of these conditions promoted the idea of a possible common link among them and CFS. Some cases also suffered from allergies, food intolerances, candidiasis, intestinal impairment, thyroid implications, endometriosis. As an initial working hypothesis, The Liver Link (TLL) was proposed in order to understand those different conditions affecting body, mind and emotional wellbeing. Considering liver implication can make a differ-ence in treatment and recovery. Low grade inflammatory conditions are related to Th2 predom-inance and liver functions. Functional disharmonies are very important because they usually still do not appear in any conventional tests. In 2002, TLL was presented as a framework to explain the concomitance of CFS and other conditions and the relationship with some viruses such as EBV, HHV, CMV, as a lecture in a congress at the University of Westminster (London). When SARS-CoV-2 outbroke, TLL helped to warn about the post-covid syndrome more likely to occur in specific individuals.

In this paper, we investigate the effects of mean stress, multiaxial loading, and residual stresses on the fatigue life of springs. We study the fatigue life of a homogeneously stressed material subjected to cyclic loading with nonzero mean stress. Traditional methods for estimating fatigue life are based on Goodman and HAIGH diagrams. The formal analytical descriptions, namely "stress-life" and "strain-life" approaches, are found to be more suitable for the numerical methods. The fatigue analysis method described above, which describes crack growth per cycle, is extended. The extensions allow consideration of the mean stress of a load cycle. Closed-form expressions for crack length versus number of cycles are derived. The complementary effects on the fatigue life of springs, which ultimately have a significant influence on the fatigue life of springs, are summarized. For the proposed unified fatigue life functions, the ranges for the stress loading factor are extended by introducing the effective stress intensity. The solution leads to the factor range for the effective stress intensity, the effective mean value of the stress intensity factor and the effective stress ratio. The developed method assumes the homogeneous stress state in the whole spring element. For the non-homogeneously loaded structural elements, the weak-link concept is applied to account for fatigue.

Little is known about how recreational triathletes prepare for an Olympic distance event. The aim of this study was to identify the training characteristics of recreational-level triathletes within the competition period and assess how their preparation for a triathlon influences their health and their levels of fatigue. During the 6 weeks prior to an Olympic distance triathlon, and the 2 weeks after, 9 recreational athletes (5 males, 4 females) completed a daily training log. Participants answered the Daily Analysis of Life Demands Questionnaire (DALDA), the Training Distress Scale (TDS), and the Alberta Swim Fatigue and Health Questionnaire weekly. The Recovery-Stress Questionnaire (REST-Q) was completed at the beginning of the study, on the day before the competition, and at the end of week 8. Training loads were calculated using session-based rating of perceived exertion (sRPE). The data from every week of training was compared to week 1 to determine how athletes’ training and health changed throughout the study. No changes in training loads, duration, or training intensity distribution were seen in the weeks leading up to the competition. Training duration was significantly reduced in week 6 (p=0.041, d = 1.58, 95% CI = 6.9, 421.9), while the number of sessions was reduced in week 6 (Z=2.32, p=0.02, ES = 0.88) and week 7 (Z = 2.31, p=0.02, ES = 0.87). Training was characterized by large weekly variations in training loads and a high training intensity. No significant changes were seen in the DALDA, TDS, or REST-Q questionnaire scores throughout the 8 weeks. Despite large spikes in training load and a high overall training intensity, these recreational-level triathletes were able to maintain their health in the 6 weeks of training prior an Olympic distance triathlon.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

Using the culture-work-health model, this study investigates the factors influencing the quality of life of maritime workers. This study conducted a survey of 320 maritime workers who have experience living and working on a ship for more than six months. This self-administered questionnaire included questions on organizational culture and support, self-efficacy, perceived fatigue, as well as the quality of work life. Organizational culture and self-efficacy were identified as factors affecting the quality of work life, while organizational support was found to have an indirect effect after passing through self-efficacy and perceived fatigue. The final model accounts for 63.1% of the variance in maritime workers’ quality of life. As such, this study shows that self-efficacy is important for the quality of life of maritime workers, having both direct and indirect effects. Moreover, organizational support may prove the primary intervention point for relieving perceived fatigue and enhancing self-efficacy, thus improving the quality of work life.

This article conducts a bibliometric analysis focusing on the influence of globalization and technology in the academic context. Previous studies have focused on analyzing the relationship between the number of research citations and international collaboration, but no study has explored it in the scope of consumer behavior and retail. Leveraging the Scopus database, the research analyzes a significant corpus of 2,111 documents from 1971 to 2022. The findings reveal a distinct surge in academic output related to the topic of technology, reflecting a growing interest in understanding the interaction between technological factors and consumer behavior. The study also explores trends in international collaboration in publications as well as its impact on citation counts.

A more sustainable society and economy also implies a more sustainable behavior in the consumption of financial products. A possible change in focus can come from the demand side, so that more sustainable consumption of financial products have to go hand to hand with financial literacy. However, financial literacy, potential favoring of this sustainable behavior, is far from reaching an international consensus about its definition, object and scope. Two objectives are analyzed; the different interpretations of financial literacy in the academic literature, as well as its evolution and how, in what context and with what other concepts the term is used in social networks. Scientometric techniques and content analysis have been used to carry out a systematic review of literature and also NLP to analyze the comments on Social Networks. Critical moments are identified in the definition of financial literacy. Also ten sentiments are analyzed in social networks in wich positivity, trust, and anticipation predominate. Greater attention to this issue is necessary both from the private initiative and from public policies, so that financial literacy is an effective tool for a more sustainable behavior by consumers. Finally, a new definition is proposed based on our findings.

Myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) is a complex, multisystem, and profoundly debilitating condition, probably of multifactorial etiology. No effective approved drugs are currently available for its treatment. Several studies have proposed symptomatic treatment with melatonin and zinc supplementation in chronic illnesses; however, little is known about the synergistic effect of this treatment on fatigue-related symptoms in ME/CFS. The primary endpoint of the study was to assess the effect of oral melatonin plus zinc supplementation on fatigue in ME/CFS. Secondary measures included participants’ sleep disturbances, anxiety/depression, and health-related quality of life. A proof-of-concept, 16-week, randomized, placebo-controlled, double-blind trial was conducted in 50 ME/CFS patients assigned to receive either oral melatonin (1 mg) plus zinc (10 mg) supplementation (n = 24) or matching placebo (n = 26) once daily. Endpoint outcomes were evaluated at baseline and then reassessed at 8 and 16 weeks of treatment and 4 weeks after treatment cessation, using self-reported outcome measures. Treatment was safe and well-tolerated. The most relevant results were the significant reduction in the perception of physical fatigue in the active group at the final follow-up versus placebo (p < 0.05), and the significant improvement in the physical component summary at all follow-up visits in the experimental group. Our findings suggest that oral melatonin plus zinc supplementation for 16 weeks is safe and potentially effective in reducing fatigue and improving the quality of life in ME/CFS. This clinical study was registered on ClinicalTrials.gov (NCT03000777).

The aim of our study was to assess university students’ sleep quality and fatigue before and during the academic exam period and identify potential associated factors. A Web-based survey was completed by 940 students of 20 different Tertiary Institutions including demographics, sleep habits, exercise, caffeine, tobacco, alcohol use, subjective sleep quality (Pittsburgh Sleep Quality Index - PSQI) and fatigue (Fatigue severity scale – FSS) at the beginning of semester and at examination period. During exam period, PSQI (8.9 vs 6.1, p&lt;0.001) and FSS scores (36.9 vs 32.7, p&lt;0.001) were significantly elevated compared to pre-exam period. Increase of PSQI score was associated with age (β=0.111, p=0.011), presence of chronic disease (β=0.914, p=0.006), and depressive symptoms (β=0.459, p=0.001). Increase of FSS score was associated with female gender (β=1.658, p&lt;0.001), age, (β=0.198, p=0.010), increase in smoking (β=1.7, p=0.029), coffee/energy drinks consumption (β=1.988, p&lt;0.001), decreased levels of physical exercise (β=1.660, p&lt;0.001), and depressive symptoms (β=2.526, p&lt;0.001). In conclusion, our results show that sleep quality and fatigue are affected in university students during exam periods. Potential factors were identified which may lead to development of strategies for better quality of sleep, and wellbeing.

Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is a complex disease characterized by profound fatigue, post-exertional malaise (PEM), and neurocognitive dysfunction. Immune dysregulation and gastrointestinal symptoms are commonly observed in ME/CFS patients. Despite affecting approximately 0.89% of the general population, the underlying pathophysiological mechanisms remain poorly understood. This study aimed to elucidate the relationship between immunological characteristics and intestinal barrier function in ME/CFS patients. ME/CFS patients were stratified into two groups based on their immune competence. After documentation of detailed medical records, serum and plasma samples were collected for assessment of inflammatory immune mediators and biomarkers for intestinal barrier integrity by ELISA. We found reduced complement protein C4a levels in immunodeficient ME/CFS patients suggesting a sub-group specific innate immune dysregulation. ME/CFS patients without immunodeficiencies exhibit a mucosal barrier leakage, as indicated by elevated levels of Lipopolysaccharide-binding protein (LBP). Stratifying ME/CFS patients based on immune competence enabled the distinction of two subgroups with different pathophysiological patterns. The study highlights the importance of emphasizing precise patient stratification in ME/CFS, particularly in the context of defining suitable treatment strategies. Given the substantial health and socioeconomic burden associated with ME/CFS, urgent attention and research efforts are needed to define causative treatment approaches.

The fixed stroke fatigue test can not simulate the real load condition of the landing gear, and the variable stroke fatigue test has increasingly become the mainstream. A modular test device for fatigue test for aircraft landing gears was designed, the automatic control of the buffer stroke was realized with ectopic displacement control technology effectively, the horizontal loading cylinder could follow the wheel axis actively with the displacement active control technology, follow-up loading along the vertical direction was realized through constructing a polar coordinate system and making the load line automatic alignment, a split-type dummy wheel was designed to improve the loading accuracy, a booster cylinder was designed to realize the control loading of high pressure combined with the hydraulic control system. The test shows that the technical scheme meets the design requirements, and the fatigue test was completed successfully. The device for landing gear variable stroke fatigue testing can be applied to other landing gear static / fatigue tests.

In the Netherlands, the assessment of existing prestressed concrete slab-between-girder bridges showed that the thin, transversely prestressed slabs may be critical for static and fatigue punching when evaluated using the recently introduced Eurocodes. On the other hand, compressive membrane action increases the capacity of these slabs and changes the failure mode from bending to punching shear. To improve the assessment of the existing prestressed slab-between-girder bridges in the Netherlands, two 1:2 scale models of an existing bridge, the Van Brienenoord Bridge, were built in the laboratory and tested monotonically as well as under cycles of loading. The result of these experiments is: 1) the static strength of the decks, showing that compressive membrane action significantly enhances the punching capacity, and 2) the Wöhler curve of the decks, showing that compressive membrane action remains under fatigue loading. The experimental results can then be used for the assessment of the most critical existing slab-between-girder bridge. The outcome is that the bridge has sufficient punching capacity for static and fatigue loads, and thus that the existing slab-between-girder bridges in the Netherlands fulfil the code requirements for static and fatigue punching.

The use of high strength to weight ratio laminated composites is emerging in marine industry and applications as a very efficient solution for improving productivity. Nevertheless, delamination between the layers is a limiting factor for the wider application of laminated composites, as it reduces the stiffness and strengths of the structure. Interleaving nanofibrous mats between layers of composite laminates has been proved to be an effective method for improving composites delamination resistance. This paper aims to characterize the effect of interleaved nanofiber on mode I interlaminar properties and failure mechanisms when subjected to static and fatigue loadings. For this purpose, virgin and nanomodified woven laminates were subjected to Double Cantilever Beam (DCB) specimens. Static and fatigue tests were performed and the tests were monitored by acoustic emission technique. The mechanical results showed a 130% increase of delamination toughness for nanomodified specimens in the static loadings and more crack growth resistance in the fatigue loading. The AE results revealed that different type of failure mechanisms was the cause of these improvements for the modified specimens compared with the virgin ones.

Developmental, clinical, and epidemiological research have demonstrated the salience of perceived racial discrimination (PRD) as a contributor to negative mental health outcomes in adolescence. This article summarizes secondary analyses of cross-sectional data from a large-scale youth survey within a predominantly rural state to estimate the prevalence and strength of association between PRD and serious psychological distress, suicidal ideation, and prior suicidal attempts. Data from 93,812 students enrolled in Grades 6, 8, 10, and 12 within 129 school districts across Kentucky were examined to determine prevalence rates for subgroups within the cohort. Logistic regression analyses assessed differences and established comparative strength of association among these variables for racial/ethnic subgroups. PRD was self-reported at high rates across several demographic subgroups and was most evident among Black (24.5%) and Asian (22.1%) students. Multiracial students experienced the highest rates of both SPD and suicidality. Both for the entire cohort and for each racial/ethnic subgroup, PRD was significantly associated with increased likelihood of negative mental health outcomes, although the strength of these associations varied across subgroups and developmental levels. Implications for early intervention and prevention are discussed.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

Post-viral fatigue syndrome (PVFS) encompasses a wide range of complex neuroimmune disorders of unknown cause characterized by disabling post-exertional fatigue, myalgia and joint pain, cognitive impairments, unrefreshing sleep, autonomic dysfunction, and neuropsychiatric symptoms. It includes myalgic encephalomyelitis, also known as chronic fatigue syndrome (ME/CFS), fibromyalgia (FM), and more recently post-COVID-19 condition (Long COVID). To date, there are no definitive clinical case criteria and no FDA-approved pharmacological therapies for PVFS. Given the current lack of effective treatments, there is a need to develop novel therapeutic strategies for these disorders. Mitochondria, the cellular organelles responsible for tissue energy production, have recently garnered attention in research into PVFS due to their crucial role in cellular bioenergetic metabolism in these conditions. Accumulating literature has identified a link between mitochondrial dysfunction and low-grade systemic inflammation in ME/CFS, FM, and Long COVID. To address this issue, this article aimed to critically review the evidence relating to mitochondrial dysfunction in the pathogenesis of these disorders; in particular, to evaluate the effectiveness of coenzyme Q10 supplementation on chronic fatigue and pain symptoms as a novel therapeutic strategy for the treatment of PVFS.

A Myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) is a debilitating chronic disease of unknown aetiology under growing interest now in view of the increasingly recognized post-COVID syndrome as a new entity with similar clinical presentation. We performed the first cross-sectional study of ME/CFS in community population in Russia and then described and compared some clinical and pathophysiological characteristics of ME/CFS and post-COVID syndrome as neuroimmune disorders. Of the cohort of 76 individuals who suggested themselves suffering from ME/CFS 56 subsequently were confirmed as having CFS/ME according to ≥1 of the 4 most commonly used case definition. Of the cohort of 14 individuals with post-COVID-19 syndrome 14 met diagnostic criteria for ME/CFS. The prevalence of clinically expressed and subclinical anxiety and depression in ME / CFS and post-COVID ME/CFS did not differ significantly from that in healthy individuals. Severity of anxiety / depressive symptoms did not correlate with the severity of fatigue neigther in ME / CFS nor in post-COVID ME/CFS, but the positive correlation was found between the severity of fatigue and 20 other symptoms of ME / CFS related to the domains of “post-exertional exhaustion”, “immune dysfunction”, “sleep disturbances”, "dysfunction of the autonomic nervous system", "neurological sensory / motor disorders" and "pain syndromes". Immunological abnormalities were identified in 12/12 patients with ME / CFS according to the results of laboratory testing. The prevalence of postural orthostatic tachycardia assessed by the active standing test was 37.5% in ME / CFS and 75.0% in post-COVID ME/CFS (the latter was higher than in healthy controls, p = 0.02) There was a more pronounced increase in heart rate starting from the 6th minute of the test in post-COVID ME/CFS compared with the control group. Assessment of the functional characteristics of microcirculation by laser doppler flowmetry revealed obvious and very similar changes in ME/CFS and post-COVID ME/CFS compared to the healthy controls. The identified pattern corresponded to the hyperemic form of microcirculation disorders, usually observed in acute inflammatory processes or in deficiency of systemic vasoconstriction influences.

This study explored the development of neuromuscular fatigue responses during progressive cycling exercise. The sample comprised 32 participants aged 22.0 ± 0.54 years who were assigned into three groups: endurance-trained group (END, triathletes, n = 10), strength-trained group (STR, body-builders, n = 10), and control group (CON, recreationally active students, n = 12). The incremental cycling exercise was performed using a progressive protocol starting with a 3 min resting measurement and then 50 W workload with subsequent constant increments of 50 W every 3 minutes until 200 W. Surface electromyography (SEMG) of rectus femoris muscles was recorded during the final 30 s of each of the four workloads. During the final 15 s of each workload, participants rated their overall perception of effort using the 20-point RPE scale. Post-hoc Tukey’s HSD testing showed significant differences between END and STR groups in MF and MPF across all workloads (p < 0.001 and p < 0.01, respectively). Athletes from END group had significantly lower AEMG responses than those from STR (p = 0.0093) and CON group (p = 0.0006). Increasing RPE points from 50 to 200 W were significantly higher in STR than in END group (p < 0.001). In conclusion, there is a significant variation in neuromuscular fatigue profiles between athletes with different training backgrounds when a cycling exercise is applied. The approximately linear trend of the SEMG and RPE values of both groups of athletes with increasing workload support the increased skeletal muscle recruitment with perceived exertion or fatiguing effect.

The fatigue life of welded joints under cyclic loading is a complex process that can be roughly divided into fatigue crack initiation, crack propagation and final fracture. Usually, these phases are evaluated separately. Several methods are available to estimate the extent of the different phases in welded components, such as stress-based fatigue concepts for crack initiation or linear elastic fracture mechanics for crack propagation; however, distinguishing these phases in welded components is a complex procedure and often relies on assumptions such as transition crack sizes. The objective of this study is to investigate the relationship between fatigue crack initiation and propagation in welded joints using artificially notched specimens with welded joints characteristics of different notch acuity (different radii and opening angle). The experiments show that the investigated relationship basically depends on the notch acuity, the load level and the stress ratio.

Consumer, as one of the vital stakeholders of fashion supply chain, has a significant role to play to transition fashion industry into sustainable direction. From purchasing and care practice to donation and disposal, every step of their decision has impact on the environment. Various internal and external variables, including culture, custom, value, belief, norm and assumption, economy, gender, and education etc. influence forming that decision. The result of the decision not only directly impacts he environment and society, but also consumer culture and future business opportunity. This study synthesizes a wide spectrum of consumer behavior related to clothing consumption and associated environmental impact. Building on the synthesis, a holistic discussion is offered which can provide relevant behavioral guideline to consumers as well as other stakeholders.

An evanescent wave is a non-propagating wave with an imaginary wave vector. In this study, we prove that these are solutions of the tachyon-like Klein–Gordon equation, and that in the tunneling of ultrarelativistic spin-1/2 particles they describe superluminal states arising from interactions between a particle and barrier. These states decay as a particle emerges from the opposite side of a potential barrier, conserving the same initial energy but not necessarily the same mass. The obtained theory is applied to the neutrino, to explain flavor oscillations during free flight and determine the conditions that maximize the probability of their occurrence.