The incorporation of polycarboxylate ether superplasticizer (PCE) type polymer and silica fume (SF) in high-performance concretes (HPC) leads to the achievement of remarkable rheological and mechanical improvements. In the fresh state, PCEs are adsorbed on cement particles and dispersants, in turn promoting the workability of the concrete. Silica fume enables a very well compacted concrete to be obtained, which is characterized by high mechanical parameters in its hardened state. Some PCEs are incompatible with silica fume, which can result in the loss of slump and in poor rheological behavior. The main objective of the research is the study of the influence of three types of PCEs, which all have a different molecular architecture, on the rheological and mechanical behavior of high-performance concretes containing 10% of SF as a partial replacement of cement. The results show that the carboxylic density of PCE has an influence on its compatibility with SF.

This research aims to understand the vision and the reaction of the population towards tourism and holidays during this period of the COVID-19 pandemic. It investigates also the tourist needs of the Algerian population after the closure of international borders. Methods: The data were collected using mixed quantitative and qualitative methods through a questionnaire applied to 203 people in different regions of Algeria (a North African country) from 1st June to 13 July 2020. Results: The needs of Algerian tourists are characterized by a great need for leisure to relieve psychological stress caused by COVID-19 (M = 25.33) among the study sample (p <0.05). The results also show an average need to rationalize the costs of tourist services (M = 5.26) according to the respondents (p <0.01). This is in addition to the great need (M = 7.75) among respondents (p <0.05) of the awareness that the tourism sector can contribute to the economic recovery in Algeria after the confinement period. About 75.86% of respondents demand the cleanliness of tourist sites, while 69.95% recommend improving safety because of the size of tourist sites in the Algerian territory and also measures related to social distancing. The results show that 53.69% of respondents preferred the month of August to go on vacation, 29.06% chose the month of September, and 17.25% would prefer the months of October, November and December since they expect a reduction in the risks of the COVID-19 pandemic. Conclusions: The COVID-19 pandemic has affected the tourism needs of the Algerian population, which has become increasingly aware of the consequences of the pandemic in relation to their health and on the country's economy. These results can help the authorities of the tourism sector to better understand and identify the tourism needs of this population in the current period and after the COVID-19 pandemic.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Controlling and understanding Cu-catalyzed homocoupling reaction is crucial to prompt the development of efficient Cu-catalyzed cross-coupling reactions. The presence of a coordinating base (hydroxide, methoxide) enables the B-to-Cu(II) transmetalation from aryl boronic acid to CuIICl2 in methanol, through formation of a mixed Cu-(μ-OH)-B intermediates. A second B-to-Cu transmetalation to form bis-aryl Cu(II) complexes is disfavored. Instead, organocopper(II) dimers undergo a coupled transmetalation-electron-transfer (TET) allowing the formation of a bis-organocopper(III) complexes readily promoting reductive elimination. Based on this mechanism some guidelines are suggested to control the undesired formation of homocoupling product in Cu-catalyzed cross-coupling reactions.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

In this work, the nearest neighbor distances and Voronoi cell features of the Cu-Ag deposits were analyzed and fitted with Lognormal, Weibull, and Gamma distributions. The nearest neighbor distance distributions of the samples were compared with those of complete spatially random points, showing spatial inhomogenity due to the nucleation exclusion effect. The radial distribution function was calculated, showing both influences from the grain size and the nucleation exclusion effect. Voronoi cells were generated based on the shape of the grains. The size, occupancy, and coordination of the Voronoi cells were examined and fitted. The results show that despite the Cu-Ag deposits seem to be governed by instantaneous nucleation mode, the spatial distribution of the nuclei is more impacted by the nucleation exclusion effect than the Cu-only samples. This behavior is also justified by the grain size distribution generated with Voronoi cell size and occupancy distributions.

Bicyclic peptides have attracted the interest of pharmaceutical companies because of their remarkable properties putting them on a new path in medicine. Their conformational rigidity that improves proteolytic stability, leads to rapid penetration into tissues via any possible route of administration and elimination, occurring by renal metabolism, is of great importance for people with a history of liver diseases. In addition, each ring can function independently, making them extremely versatile molecules for further optimization. In this paper we compared the potentiometric and spectroscopic properties studied by UV-Vis, MCD, and EPR, of four synthetic analogues of the bi-cyclic peptide c(PKKHP-c(CFWKTC)-PKKH). In particular we correlated the structural and spectral properties of complexes with coordinating abilities toward Cu(II) ions of MCL (Ac-PKKHPc(CFWKTC)PKKH-NH2) that contains the unbinding cycle and N- and C-terminal linear parts, with two histidine residues, one per part; two monocyclic ligands containing one histidine residue, both in the N-terminal position i.e., MCL2 (Ac-PKKHPc(CFWKTC)PKKS-NH2) and in the C-terminal position i.e., MCL3 (Ac-PKKSPc(CFWKTC)PKKH-NH2), respectively, and the linear structure LNL (Ac-PKKHPSFWKTSPKKH-NH2).

Cu-ions dispersed on reduced graphene RGo prepared and characterized in a liquid state in ethanol. Either constant ultrasounds or a sequence of ultrasounds (15s working, 15s stop) were applied for 6 min or 2h overall time, at a power of 500 W. Commercial graphite in ethanol was introduced at a concentration of 0.04 g/mL and CuCl2 2.5 H2O concentrations between 0.012 and 0.04 g/mL were used. The structural characterizations performed by XRD, microscopic, and spectroscopic techniques, after a centrifugation at 5000 rpm applied 12 min before Cu-introduction, led to conclude that: 1) Without copper, negative peaks in UV spectra were detected with concentrated pure graphene solutions, indicating light emission as nicely confirmed next by fluorescence measurements, 2) After addition of copper chloride and equilibration for 2 min , very intense and narrow peaks of intensity larger than 10 were observed. These peaks due to collective excitations generating plasmons were suppressed at a higher dilution and also if the cell with one cm optical path was replaced by a narrower cell with a 0.2 cm path. When plasmons were suppressed, in the UV spectral range, a band gap due to the energy transition between the valence filled  orbitals and conducting empty * orbitals, was observed. The presence of Cu (II) and Cu (I) cations were evidenced by Visible NIR spectroscopy. The formed “green” liquors containing Cu (II) Cu (I) /graphene in ethanol were stable in air for months and had good photocatalytic visible properties as demonstrated by the decomposition of two dyes.

In this study, Cu/Ni and Cu/Al multilayer thin films with individual layer thickness varying from 25 nm to 200 nm were deposited at room temperature and further annealed up to 300 ℃. The mechanical and microstructural properties of the multilayers were characterized by nanoindentation, x-ray diffraction, and scanning electron microscopy. Both systems exhibited an increase in hardness with increasing annealing temperature. However, the Cu/Ni system showed a gradual and moderate (up to 30%) hardness increase from room temperature to 300 ℃, while the Cu/Al system showed a sharp increase (~150%) between 125℃ and 200℃. This distinct strengthening behavior is attributed to solid solution formation in Cu/Ni and diffusion-activated intermetallic formation in Cu/Al.

The development of the additive manufacturing (AM) technology proffers challenging requirements for forming accuracy and efficiency. In this paper, a hybrid additive manufacturing technology combining fusion-based selective laser melting (SLM) and solid-state cold spraying (CS) was proposed in order to enable the fast production of near-net-shape metal parts. The idea is to fabricate a bulk deposit with a rough contour first via “fast” CS process and then add fine structures and complex features through “slow” SLM. The experimental results show that it is feasible to deposit SLM part onto CS part with good interfacial bonding. However, the CS parts must be subject to heat treatment to improve their cohesion strength before being sending for SLM processing. Otherwise, the high tensile residual stress generated during SLM process will cause fracture and cracks in the CS part. After heat treatment, pure copper deposited by CS undergoes grain growth and recrystallization, resulting in improved cohesive strength and release of the residual stress in the CS parts is released. The tensile test on the SLM/CS interfacial region indicates that the bonding strength increased by 38% from 45±7 MPa to 62±1 MPa after the CS part is subject to heat treatment, and the SLM/CS interfacial bonding strength is higher than the CS parts. This study demonstrates that the proposed hybrid AM process is feasible and promising for manufacturing free-standing SLM-CS components.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

Bimetallic Ni/Cu core-shell and Cu-Ni heterostructural micro- and nanoparticles were prepared using two simple successive reduction procedures. Monometallic Ni and Cu particles were synthesized for comparison. The phase constitutions and morphological features of the particles were studied by means of X-ray diffraction, energy-dispersive X-ray spectroscopy and scanning electron microscopy methods. All the obtained mono- and bimetallic particles were applied as electrocatalysts in the electrohydrogenation of p-nitrophenol (p-NPh). An additional electrochemical reduction of copper cations during the hydrogen saturation of Cu-containing particles was established. Some of the prepared particles exhibited high catalytic activity with an increase in the hydrogenation rate of p-NPh by more than 3 times compared to its electrochemical reduction on the non-activated cathode, and p-NPh conversion yielded the maximum values. The main product of p-NPh electrocatalytic hydrogenation over Ni-Cu particles is p-aminophenol, which is an intermediate in the synthesis of many drugs. p-Aminophenol formation is confirmed by UV-Vis spectra.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

In this paper, the nanoscale dissipative mechanisms of a Cu pad in a Ball Grid Array (BGA) packaging structure during isothermal ageing and uniaxial tension were investigated by the molecular dynamics (MD) method and experiments. From the result of the isothermal ageing test, a nonuniform consumption of Cu and large amount of Kirkendall voids were observed at the interface of Cu and Cu₃Sn. To study the effect of pressure and orientation on this phenomenon, MD simulations were conducted on four types of Cu-Cu₃Sn interface structures with different orientations of Cu. By comparing the diffusion coefficients of atoms in those cases, it was found that the tensile stress would inhibit the diffusion of atoms, whereas compressive stress would accelerate it, and this would be more significant under a larger magnitude of stress and temperature. Note that, in the model with the (101) surface Cu at the interface, both Cu and Cu₃Sn have a higher diffusion coefficient compared with the model with (001) surface Cu. Thus, the orientation of Cu will also contribute to the uniform consumption of the pad. Uniaxial tension simulation combined with DXA and CSP analyses on those models also shows the model with (001) surface Cu has a greater mechanical reliability in our simulations and related experiments.

Sphalerite has been recognized as the most important carrier of critical metal of Indium (In) due to that In mainly exists in the sphalerite lattice by isomorphic substitution. There are two significant replacing schemes for In entry into sphalerite, these are, Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+. In order to understand the reaction process and constraints of the two substitution schemes, this paper uses first-principles methods to calculate In and Ag, Cu replacing Zn in sphalerite. According to the substitution schemes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, two doped sphalerite systems of Zn30InAgS32 and Zn30InCuS32 were constructed using 2×2×2 supercell model of sphalerite. Firstly, the pressure is controlled to 30MPa, and the temperature is set from 20-40MPa to simulate the response of the two doped sphalerite systems to temperature; Then, the control temperature was unchanged to 600K, and the pressure was set from 20-40MPa to investigate the pressure control of the two doped sphalerite systems. The lattice parameters, substitution energy, electronic structure, and population analysis of the designed models before and after replacement have been critically compared. The main conclusions can be drawn that it is more stable for In to enter sphalerite via the coupled substitution scheme Cu++In3+→2Zn2+, and the conditions that the two substitution schemes most likely to occur are 650K and 40MPa. This study not only reveals the physical and chemical properties of In-rich sphalerite formed by the two reaction processes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, but also has a certain enlightenment effect on the search for indium in sphalerite, and promotes the application of first principles in mineralization analysis.

Copper-based nanoparticles were synthesized using the glycine–nitrate process (GNP) by using copper nitrate trihydrate [Cu(NO₃)₂‧3H₂O] as the main starting material and glycine [C₂H₅NO₂] as the complexing and incendiary agent. The as-prepared powders were characterized through X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) analysis, X-ray photoelectron spectroscopy, and scanning electron microscopy. Using Cu(NO₃)₂.3H₂O as the oxidizer (N) and glycine as fuel (G), we obtained CuO, mixed-valence copper oxides (CuO + Cu₂O, G/N = 0.3–0.5), and metallic Cu (G/N = 0.7). The XRD and BET results indicated that increasing the glycine concentration (G/N = 0.7) and reducing particle surface area increased the yield of metallic Cu. The effects of varying reaction parameters such as catalyst activity, catalyst dose, and H₂O₂ concentration on nonylphenol-9-polyethoxylate (NP9EO) degradation were assessed. With a copper‐based catalyst in a heterogeneous system, the NP9EO and total organic carbon removal efficiencies were 83.1% and 70.6%, respectively, under optimum operating conditions (pH, 6.0; catalyst dose, 0.3 g/L; H₂O₂ concentration, 0.05 mM). The results suggested that removal efficiency increased with an increase in H₂O₂ concentration but decreased when the H₂O₂ concentration exceeded 0.0.5 mM. Furthermore, the trend of photocatalytic activity was as follows: G/N = 0.5 > G/N = 0.7 > G/N = 0.3. The G/N = 0.5 catalysts showed the highest photocatalytic activity and resulted in 94.6% NP9EO degradation in 600 min.

Cu,N-TiO₂ nanotube (Cu,N-TNT) is prepared through a novel magnetron sputtering and anodic oxidation method. Then the morphology, structure and physicochemical property of Cu,N-TNT was analyzed by XRD, SEM, TEM, EDX and UV-vis-DR. The results indicate that the evenly doped copper is beneficial to the transformation of the TNT from anatase to rutile and play a key role in the morphology of the Cu,N-TNT. The doped Cu and N in the TNT influence the growth orientation of the TiO₂ crystals, which result in the lattice distortion and wider the interplanar spacing 60s-Cu,N-TNT has less band gap and stronger absorption intensity in visible region than other Cu,N-TNT samples, which make the combination rate of photogenerated electron and photogenerated hole decrease greatly, thus beneficial to its physicochemical property.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

The neurodegenerative diseases (Alzheimers, Parkinsons, amyotrophic lateral sclerosis, Huntingdons) and the prion disorders, have in common a dysregulation of metalloprotein chemistry involving redox metals (Cu,Fe,Mn). The consequent oxidative stress gives rise to protein plaques and neuronal cell death. An equilibrium exists between the functional requirement of the brain for Cu and Fe and their destructive potential with the production of reactive oxygen species. The importance of the brain barrier is highlighted in regulating the import of these metals. Upregulation of key transporters occurs in foetal and neonatal life when brain metal requirement is high and is down-regulated in adult life when need is minimal. By contrast a neonatal mode of CTR1 upregulation persists in feral N.Ronaldsay sheep. This has led to the premise that metal regulation may return to the default setting in ageing with implications for neurodegenerative disease.

The unfolded band structure and optical properties of Cu-doped KCl crystals were computed by first principles within the framework of density functional theory, implemented in the ABINIT electronic structure package utilizing pseudopotential approximation and a plane-wave basis set. From a theoretical point of view, Cu substitution into pristine KCl crystals requires calculation by the supercell (SC) method. This procedure shrinks the Brillouin zone, resulting in a folded band structure that is difficult to interpret. To solve this problem and gain insight into the effect of copper ions (Cu+) on electronic properties, the band structure of SC KCl:Cu was unfolded to make a direct comparison with the band structure of the primitive cell (PC) of pristine KCl. To understand the effect of Cu substitution on optical absorption, we calculated the imaginary part of the dielectric function of KCl:Cu through a sum-over-states formalism and broke it down into different band contributions by partially making an iterated cumulative sum (ICS) of selected valence and conduction bands. Consequently, we identified those interband transitions that give rise to the absorption peaks due to the Cu+ ion. These transitions involve valence and conduction bands formed by the Cu-3d and Cu-4s electronic states

This review focuses on Cu/TiO2 sequentially and Cu-TiO2 co-sputtered catalytic/photocatalytic surfaces leading to bacterial inactivation discussing their stability, synthesis, adhesion and antibacterial kinetics. The intervention of TiO2, Cu and the synergic effect of Cu and TiO2 on films prepared by a colloidal approach and other techniques is also reviewed leading to bacterial inactivation. Processes in aerobic media and anaerobic media leading to bacterial loss of viability on multidrug resistant (MDR) pathogens, Gram-negative (-) and Gram-positive(+) bacteria are described. Insight is provided for the interfacial charge transfer mechanism under solar irradiation occurring between TiO2 and Cu. surface properties of 2D TiO2/Cu and TiO2-Cu films are correlated with the bacterial inactivation kinetics observed in the dark and under light. The intervention of these antibacterial sputtered surfaces in health-care facilities leading to MRSA-isolates is described in the dark and under the actinic light. The synergic intervention of the Cu and TiO2 films leading to bacterial inactivation prepared by direct current magnetron sputtering (DCMS), pulsed direct current magnetron sputtering (DCMSP) and highly ionized pulse plasma magnetron sputtering (HIPIMS) is reported in a detailed way.

Excessive CO₂ emissions and alternative energy fuels are two major difficult issues. The utilization of CO₂ into fine chemicals is an optimal route. Diethyl carbonate (DEC) is an extremely versatile chemical intermediate. DEC is used in gasoline, pharmaceutical, chemical and other fields. DEC synthesis from CO₂ and ethanol is a typical green synthetic route. Ni-Cu@Na₃PW₁₂O₄₀ catalysts were synthesized by two novel methods of supported and mixed. The catalyst prepared by mixed method showed nice catalytic performance. It was confirmed that water removal was the key to improving conversion efficiency. In the presence of dehydrating agent of ethylene, ethanol conversion increased from ca. 3% to ca. 40%. Propylene oxide (PO) was participated in the reaction and ethanol conversion continued to reach to ca.90% while DEC selectivity dropped by half. Under optimal conditions, our Ni-Cu@Na₃PW₁₂O₄₀ catalyst effectively solved the two major issues above.

Coastal erosion is threatening the infrastructures of coastal community at the Ma River mouth in Thanh Hoa province, Vietnam. When coastal erosion happens, people try to prevent it by emergency solutions like hard structures. However, this approach usually leads to more severe problem since the mechanism for coastal erosion is not investigated and understood properly. In this study the long-term configuration of Ma River mouth in Thanh Hoa Province, Central Vietnam has been investigated using Landsat imagery from 1987 to 2023. An analytical solution of one-line model for shoreline change was also employed to calculate the sand discharge from Ma River as well as the diffusion coefficient for sand transported along-shore by breaking waves. There was an asymmetric configuration of the Ma River mouth during the last 37 years. The sand supply from the Ma River is around 350,000 m3/year. This amount of sand is going mainly to the northern beach of the Ma River delta (from 55% to 75%). The asymmetric morphology of the Ma River mouth delta is the trigger for severe coastal erosion reported recently. This study provides a quick and easy method to investigate the morphological change of cuspate deltas where measured data is limited.

In order to search possible residual minor phases in Y-Ba-Cu-O family, powdered mixtures of Y₂O₃ + BaCO₃ + CuO and, independently, superconducting compound YBa₂Cu₃O_7-x have been treated in evacuated cells and elevated temperatures.YBa₂Cu₃O_7-x was reduced to YBa₂Cu₃O₅ by use of the special home designed Taconis-Knudsen vacuum device. A subsequent doping by oxygen converts produced insulator YBa₂Cu₃O₅ to semiconductor or metal YBa₂Cu₃O_5+x (0<x<0.3). In addition to YBa₂Cu₃O₅, 0.05 volume percent of the minor delafossite phase Y₂Cu₂O₄ was being spotted in the powder mixture 1/2 Y₂O₃ + 2BaCO₃+6Cu₂O, heated up to 818 °C in an inert gas atmosphere. An attempt to prepare the insulating bulk delafossite samples was successful, and subsequent doping by oxygen produces novel metallic phases.

Background: The use of nitinol (NiTi) archwires in orthodontic treatment has expanded significantly due to unique mechanical properties. The greatest barrier to safe orthodontic treatment is chemically or microbiologically induced corrosion, resulting in Ni2+ release. The aim of this investigation was to enhance corrosion resistance and introduction antibacterial properties to NiTi archwire by coating them with TiN-Cu. Methods: NiTi archwires were coated with TiN-Cu using cathodic arc evaporation and direct current magnetron sputtering. The morphology of the sample was analyzed by FESEM and the chemical composition was assessed using EDS, XRD and FTIR. Inductively coupled plasma-optical emission spectrometry was used to estimate the ion release. Biocompatibility of samples was investigated using MTT test. Antibacterial activity was analyzed against Streptococcus mutans and Streptococcus mitis. Results: Physico-chemical characterization revealed well-designed coatings with the presence of TiN phase with incorporated Cu2+. TiN-Cu coated archwires showed statistically lower Ni2+ release (p<0.05). Relative cell viability was the highest regarding 28-day eluates of TiN-Cu coated archwires (p<0.05). The most remarkable decrease in Streptococcus mitis concentrations was observed in case of TiN-Cu coated archwires (p<0.05). Conclusion: Taking into account biocompatibility and antibacterial tests, TiN-Cu coated archwires may be considered as a good candidate further clinical investigations.

The influence of the grain structure on the tensile deformation strength is studied for precipitation-strengthened Cu-0.2%Zr at 673 K. Subgrains and grains are formed by ECAP and annealing. The fraction of high-angle boundaries increases with prestrain. Subgrains and grains coarsen during deformation. This leads to softening in the quasi-stationary state. The initial quasi-stationary state of severely predeformed, ultrafine-grained material exhibits relatively high rate-sensitivity at relatively high stresses. This is interpreted as result of the stress dependences of the quasi-stationary subgrain size and the volume fraction of subgrain-free grains.

The local electrical response in alkaline-doped CuInSe₂ films prepared by single step electrodeposition onto Cu substrates was studied by current sensing atomic force microscopy. The CIS films were prepared from single baths containing the dopant ions (Li, Na, K or Cs) and were studied by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy and photocurrent response. Increased crystallinity and surface texturing as the ion size increases was observed as well as enhanced photocurrent response in Cs doped CIS. Li and Na doped films have larger conductivity than the undoped film while the K and Cs doped samples display shorter currents and the current images indicate strong charge accumulation in the K and Cs doped films forming surface capacitors. Corrected CAFM IV curves were adjusted with Shockley equation.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

Cu-Sn shape-memory microwires were fabricated by a glass-coated melt spinning method. Effects of Sn content on the microstructure and mechanical property of microwires were investigated. The phase transforms from martensite to austenite with Sn content increasing from 14.0 atomic percent (at.%) to 16.5 at.%, and highly ordered intermetallic phase, δ, formed with higher Sn content. The fracture stress, σf, and the critical stress for martensitic transformation, σMs, increases with Sn content increasing. The mechanical property as well as superelasticity were improved greatly by high cooling rate of the glass-coated melt spinning method.

Thin Pd-40%Cu films were obtained by the classical melting and rolling method, magnetron sputtering and modified with nanostructured functional coatings to intensify the process of hydrogen transport. The films were modified by electrodeposition according to the classical method of obtaining palladium black and "Pd-Au nanoflowers" with spherical and pentagonal particles, respectively. The experiment results demonstrated the highest catalytic activity (89.47 mA cm–2), good resistance to CO poisoning and long-term stability of Pd-40%Cu films with a pentagonal structured coating. The investigation of the developed membranes in the hydrogen transport processes in the temperature range of 25-300°C also demonstrated high and stable fluxes up to 475.28 mmol s–1 m–2 (deposited membranes) and 59.41 mmol s–1 m–2 (dense-metal membranes), which turned out to be up to 1.5 higher compared to membrane materials with classic niello. For all-metal modified membranes, the increase in flux was up to 7 times, compared with a smooth membrane made of pure palladium, and for deposited films, this difference was several tens of times. The membrane materials selectivity was also high up to 4419. The developed strategy for modifying membrane materials with functional coatings of a fundamentally new complex geometry can shed new light on the development and fabrication of durable and highly selective palladium-based membranes for gas steam reformers.

Abstract: Arranged patterns obtained by ultrafast laser processing on the surface of Ti/Cu/Ti/Si and Ti/Zr/Ti/Si thin film systems are reported. Two differently designed multilayer thin films, Ti/Cu/Ti/Si and Ti/Zr/Ti/Si, were deposited on silicon by the ion sputtering method. The bioactive surfaces on these systems involve the formation of laser-induced periodic surface structures (LIPSS) in each of the laser-written lines of mesh patterns on 5x5 mm areas. The formation of nano- and micro-patterns with an ultra-thin oxide film on the surfaces was used to observe the effects of morphology and proliferation of the MRC-5 cell culture line. To determine whether Ti-based thin films have a toxic effect on living cells, an MTT assay was performed. The relative cytotoxic effect as a percentage of surviving cells showed that there was no difference in cell number between the Ti-based thin films and the control cells. There was also no difference in the viability of the MRC-5 cells, except for the Ti/Cu/Ti/Si system, where there was a slight 10% decrease in cell viability.

Voids in face-centered cubic (fcc) metals are commonly assumed to form by the aggregation of vacancies; however, the mechanisms of vacancy clustering and diffusion are not fully understood. In this study, we use computational modeling to provide a detailed insight into the structures and formation energies of primary vacancy clusters, mechanisms and barriers for their migration in bulk copper, and how these properties are affected at simple grain boundaries. The calculations were carried out using Embedded Atom Method (EAM) potentials and Density Functional Theory (DFT) and employed the Site-Occupation Disorder code (SOD), the Activation Relaxation Technique nouveau (ARTn) and the Knowledge Led Master Code (KLMC). We investigate stable structures and migration paths and barriers for clusters of up to six vacancies. Migration of vacancy clusters occurs via hops of individual constituent vacancies with di-vacancies having a significantly smaller migration barrier than mono-vacancies and other clusters. This barrier is further reduced when di-vacancies interact with grain boundaries. This interaction leads to the formation of self-interstitial atoms and introduces significant changes into the boundary structure. Tetra-, penta-, and hexa-vacancy clusters exhibit increasingly complex migration paths and higher barriers than smaller clusters. Finally, the direct comparison with the DFT results shows that EAM can accurately describe the vacancy-induced relaxation effects in the Cu bulk and in grain boundaries. Significant discrepancies between the two methods were found in structures with a higher number of low-coordinated atoms, such as penta-vacancies and di-vacancy absortion by grain boundary. These results will be useful for modeling the mechanisms of diffusion of complex defect structures and provide further insights into the structural evolution of metal films under thermal and mechanical stress.

Superconducting split ring resonator arrays allow to overcome two main limitations affecting metallic metamaterial resonating in the Terahertz (THz) range: Ohmic losses and tunability of their optical response. In this work, we design and experimentally realize direct and complementary square arrays of superconducting YBa2Cu3O7 (YBCO) split ring resonators working in the THz spectral range. The main purpose of this paper is to show how the metamaterial resonances can be tuned by temperature (T) when crossing the superconducting transition temperature Tc of YBCO. The tuning property can be quantified by describing the THz transmittance of the patterned YBCO films vs. T through a model of coupled resonators. This model allows us to estimate the THz resonances of split-ring arrays and their interaction, showing how the kinetic inductance Lk in the superconducting state is the main parameter affecting the metamaterial properties.

Molecular dynamics simulations were carried out to investigate the atomic structure of a model Cu64Zr36 bulk metallic glass (BMG). It is found that the amount of icosahedral content of the system is significantly increased in a well relaxed structure. While we considered four connection types of vertex-, edge-, face-, and volume-sharing, the huge cluster in the relaxed samples mainly involve volume-type connection and exhibits a remarkable athermal plasticity that great stiffness and great yield strength compared to the as-quenched samples. In addition, the bond-angle distribution of annealed sample shows sharp peaks at specific bond angles which is an evidence of crystallized Laves-phase formed by icosahedral atoms, however the peaks are to be broaden after loading, which indicates decreasing amount of icosahedral content and their shape distortion. These results suggest that icosahedral content in a bulk metallic glasses plays a key role to determine the mechanical properties such as rigidity and maximum stress carrying capacity.

An array of Ag nanowires has been prepared from a facile, templated approach on Cu(BTC) (1,3,5-benzenetricarboxylic acid) metal organic framework (MOF) micropillars. The Ag-deposited scaffolding material may be used to prepare electronic or optoelectronic devices for various applications.

Cost-efficient catalyst for hydrogen evolution reaction (HER) and methanol oxidization reaction (MOR) is of great importance for industrial application. The alloying of platinum with cheap transition metal offers a great opportunity to reduce cost and enhance the electro-catalytic performance. Herein, we report a simple and green route to synthesize porous Pt-Cu catalysts, where Pt-Cu solid particles were first produced by using cuprous chloride (CuCl) nanoparticles as the template, followed by a dealloying treatment to obtain final porous product. The porous alloy nanoparticles show higher catalytic activity and superior stability for HER and methanol oxidation reaction, which is beneficial from the porous structure and synergetic effect between Pt and Cu.

Reactions of N‚N'-bis(3-methylpyridyl)oxalamide (L1), N,N’-bis(3-methylpyridyl)adipoamide (L2) and N,N’-bis(3-methylpyridyl)sebacoamide (L3) with tricarboxylic acids and Cu(II) salts afforded {[Cu(L1)(1,3,5-HBTC)]·H2O}n (1,3,5-H3BTC = 1,3,5-benzenetricarboxylic acid), 1, {[Cu1.5(L2)1.5(1,3,5-BTC)(H2O)2]·6.5H2O}n, 2, [Cu(L2)0.5(1,3,5-HBTB)]n (1,3,5-H3BTB = 1,3,5-tri(4-carboxyphenyl)benzene), 3, [Cu4(L3)(OH)2(1,3,5-BTC)2]n, 4, {[Cu3(L3)2(1,3,5-BTB)2]·2.5MeOH·2H2O}n, 5, and {[Cu3(L3)2(1,3,5-BTB)2 ]·DMF·2H2O}n, 6, which have been structurally characterized by using single crystal X-ray crystallography. Complexes 1 – 4 form a 2D layer with the {44.62}-sql topology, a 2D layer with the (4.62)2(42.62.82)-bex topology, a 3-fold interpenetrated 3D net with the (412.63)-pcu topology and a 3D framework with the (410.632.83)(42.6)2(43.63) topology, respectively, whereas 5 and 6 are 3D frameworks with the (63)2(64.82)(68.85.102) topology. Complex 5 shows a better iodine-adsorption factor of 290.0 mg g-1 at 60 oC for 360 minutes than the other ones, revealing that the flexibility of the spacer ligand governs the structural diversity and the adsorption capacity.

The removal of metal ions by biosorption on inexpensive materials is still a challenge for environmental engineering research. In this study, marine green algae biomass (Ulva lactuca sp.) and the biochars obtained from this biomass, at 320 C (BC-320) and 550 C (BC-550), were used as biosorbents for the removal of Cu(II) ions from aqueous solution. In addition to comparing the biosorption capacities, the determination of the thermodynamic parameters allows the choice of the most suitable material for the biosorption processes. The experimental results, obtained for Cu(II) ions biosorption on each biosorbent (algae biomass (AB), BC-320 and BC-550), at three different temperatures (10, 30 and 50 C) were analyzed using Langmuir and Freundlich isotherm models, while pseudo-first order, pseudo-second order and intra-particle diffusions models were used to model the kinetic data. The biosorption of Cu(II) ions is best described by the Langmuir model and the pseudo-second kinetic model, regardless of the type of biosorbent. The maximum biosorption capacity (qmax, mg/g) depends on the temperature, but also on the type of biosorbent, and follow the order: BC-320 &lt; AB &lt; BC-550. Using the experimental isotherms, the thermodynamic parameters (G0, H0 and S0) for the biosorption of Cu(II) ions on each biosorbent were calculated. The analysis of the obtained values constitutes the main arguments in choosing BC-550 as the most effective biosorbent for the removal of Cu(II) ions from aqueous media.

Al-Zn-Mg-Cu alloy has high specific strength, good corrosion resistance, fracture toughness and fatigue resistance. It is one of the most important structural materials in the fields of aviation, aerospace, weapons, transportation and so on, which plays a huge role in the field of aerospace.In order to optimize the strength, toughness and corrosion properties of Al-Zn-Mg-Cu alloy, alloying has always been the focus of research on Al-Zn-Mg-Cu alloy. The effects of main alloying elements, trace alloying elements and rare earth elements on the microstructure and properties of Al-Zn-Mg-Cu aluminum alloy were briefly introduced in the paper, and the future research directions were prospected.

The influence of pore size on the toughness of Fe-Mo-Cu-C sintered and carburized components was investigated. The charpy impact value of the component made from Fe-0.4%Mo diffusion-alloyed steel powder mixed with 2%Cu powder and 0.3% graphite powder significantly increased with a decrease in pore size. The highest impact value of 17 J/cm2 was obtained at the average pore size of 12 µm. This value was 25% higher than that of the sintered and carburized component made from conventional Fe- 4%Ni-1.5%Cu-0.5%Mo alloyed steel powder called 4Ni even though the component was made from a Ni-free alloyed steel powder. The mechanism of the improvement of the impact value by pore size refinement and the influence of microstructural difference between the components made from Fe- 0.4%Mo diffusion-alloyed steel powder and 4Ni on toughness is discussed based on optical microstructural observation and crystal orientation analysis data.

Mitigation of Anthropogenic CO2 emissions possess a major global challenge for modern societies. Herein catalytic solutions are meant to play a key role. Among the different catalysts for CO2 conversion Cu supported on molybdenum carbide is receiving increasing attention. Hence, in the present communication we show the activity, selectivity and stability of fresh-prepared -Mo2C catalysts and compare the results with those of Cu/Mo2C, Cs/Mo2C and Cu/Cs/Mo2C in CO2 hydrogenation reactions. The results showed that all the catalysts were active and the main reaction product was methanol. The results showed that copper-cesium and molybdenum effectively interact and that cesium promoted the formation of metallic Mo. While, the incorporation of copper is positive to improve the activity and selectivity to methanol, the presence of Mo0 phase was detrimental for the conversion and selectivity. Moreover, the catalysts promoted by cesium underwent redox surface transformations during the reaction that diminished their catalytic performance. The molybdenum phase in Cu/Mo2C changes during reaction leading to metallic molybdenum and tuning the catalytic activity.

In our previous study, a novel barrier processing on a porous low-dielectric constant (low-k) film was developed: an ultrathin Mn oxide on a nitrogen-stuffed porous carbon-doped organosilica film (p-SiOCH(N)) as a barrier of the Cu film was fabricated. To form a better barrier Mn₂O_3-xN film, an additional annealing at 450°C was implemented. In this study, the electrical characteristics and reliability of this integrated Cu/Mn₂O_3-xN/p-SiOCH(N)/Si structure is investigated. The proposed Cu/Mn₂O_3-xN/p-SiOCH(N)/Si capacitors exhibited poor dielectric breakdown characteristics in the as-fabricted stage, although, less degradation was found after thermal stress. Moreover, its time-dependence-dielectric-breakdown electric-field acceleration factor slightly increased after thermal stress, leading to a larger dielectric lifetime in a low electric-field as compared to other MIS capacitors. Furthermore, its Cu barrier ability under electrical or thermal stress was improved. As a consequent, the proposed Cu/Mn₂O_3-xN/p-SiCOH(N) scheme is a promising integrity for back-end-of-line interconnects.

Abstract:The Schiff bases obtained from formylmenthone and o-, m-, p-toluidine behave as bidentate ligands with O and N donor atoms in Ni(ll) and Cu(II) complexes by the type NiL2 and CuL2.(H2O)2. The donor atoms and the possible geometry for the complexes were assigned by means of chemical, thermodifferential analyses and electronic, EPR and IR spectra.

A series of dinuclear copper(I) N,C,N- and P,C,P-carbodiphosphorane (CDP) complexes using multidentate ligands CDP(Py)2 (1) and (CDP(CH2PPh2)2 (13) have been isolated and characterized. Detailed structural information was gained by single crystal XRD analyses of nine representative examples. The common structural motive is the central double ylidic carbon atom with its characteristic two lone-pairs involved into binding of two geminal L-Cu(I) fragments at Cu-Cu distances in the range 2.55 – 2.67 Å. In order to enhance conformational rigidity within the characteristic Cu-C-Cu triangle, two types of chelating side arms were symmetrically attached to each phosphorus atom: two 2-pyridyl functions in ligand CDP(Py)2 (1) and its dinuclear copper complexes 2-9 and 11, as well as two diphenylphosphinomethylene functions in ligand CDP(CH2PPh2)2 (13) and its di- and mononuclear complexes 14-18. Neutral complexes were typically obtained via reaction of 1 with Cu(I) species CuCl, CuI, and CuSPh or via salt elimination reaction of [(CuCl)2(CDP(Py)2] (2) with sodium carbazolate. Cationic Cu(I) complexes were prepared upon treating 1 with two equivalents of [Cu(NCMe)4]PF6, followed by the addition of either two equivalent of an aryl phosphine (PPh3, P(C6H4OMe)3) or one equivalent of a bisphosphine ligands DPEPhos, XantPhos or dppf. For the first time carbodiphosphorane CDP(CH2PPh2)2 (13) could be isolated upon treating its precursor [CH(dppm)2]Cl (12) with NaNH2 in liquid NH3. A protonated and a deprotonated derivative of ligand 13 were prepared and their coordination was compared to neutral CDP ligand 13. NMR analysis and DFT calculations reveal, that the most stable tautomer of 13 does not show a CDP (or carbone) structure in its uncoordinated base form. For most of the prepared complexes, photoluminescence upon irradiation with UV light at room temperature was observed. Quantum yields (PL) were determined to 36% for dicationic [(CuPPh3)2(CDP(Py)2)](PF6)2 (4) and to 60% for neutral [(CuSPh)2(CDP(CH2PPh2)2] (16).

In this study, a modular multi-step photometric microflow injection analysis (micro-FIA) system for the automatic determination of Cu(II) in a bioreactor has been developed. The system incorporates diverse 3D-printed modules, including a platform formed by a mixer module to mix Cu(II) with hydroxylamine which reduces Cu(II) to Cu(I) linked to a diluter module via a Tesla valve, a chelation mixer module, a disperser module, and a detector module provided by a LED light source at λ= 455 nm and a light dependence resistor (LDR) as a light intensity detector. The system measures the color intensity resulting from the chelation between Cu(I) and neocuproine. The micro-FIA system has demonstrated good capability for automatic and continuous Cu(II) determination, in a wide range of Cu concentrations from 34 to 2000 mg L-1. The device exhibits a good repeatability (coefficient of variation below 2% across the concentration range), good reproducibility, and has an accuracy of around 100% between 600 to 1900 mg·L-1. Real samples were analyzed using both the micro-FIA system and an atomic absorption spectroscopy method, revealing no statistically significant differences. Additionally, a Tesla valve located before the detector substituted a 3-way solenoid valve, eliminating the need for moving parts.

Various methods including electrochemical purification, chemical precipitation, solvent extraction, and ion-exchange resins, have maturely been used for removal of copper from nickel anolyte. Interestingly, these approaches of copper removal from nickel anolyte by precipitation are well used as the primary industrial method in nickel production again. However, these methods suffer from several severe drawbacks in industrial practices. One is that a small amount of nickel precipitates with copper in slags，resulting in slag treatment difficulties. Second, this process requires an extremely high activity of the sulfide-based copper removal agents which results in high production costs; the short storage period of the copper removal agent is another drawback of this method. These have been the key challenges in the smelting process of nickel. Herein, we present a comprehensive review of the nickel removal methods used for nickel anolyte purification, electrochemical purification, chemical precipitation, solvent extraction, and ionexchange resins. The advantages and feasibilities of each technique in industrial applications are also explored and analyzed. Finally, we demonstrate that ion-exchange resin-based extraction method can pave a new path for metallurgical research on nickel.

Copper is a heavy metal used in many industries and known for its negative impacts on the environment and human’s health. A novel structured metal organic framework (MOF) was used for copper adsorption for this work. SEM, EDAX, XRD and FTIR were done to confirm the structure of MOF prepared. MOF of 0.05 gm was used to examine its ability in Cu+ 2 removals with different initial concentrations of Cu+2 and pH values (5, 7 and 9). The prepared MOF was able to achieve Cu removal with 94.6%, 93%, 91.5%, and 92.5 % for the initial concentrations of 5, 10, 15, and 20 ppm respectively. It also performed very well for pH 5 and 7 with average removal ranging from 93.9%-95% for pH 5 and 7 for the initial concentrations of 5, 10, and 15 respectively which indicate that the prepared MOF is of high ability in Cu+ 2 removal.

In this study, the hot deformation of Cu-0.55Sn-0.08La (wt%) alloy was studied by gleeble-3180 testing machine at deformation temperatures of 400-700oC and various strain rates. The stress-strain curve showed that the hot deformation behavior of Cu-0.55Sn-0.08La (wt%) alloy was greatly affected by work hardening, dynamic recovery, and dynamic recrystallization. The activation energy Q was calculated as 287.141 kJ/mol , and hot compression constitutive equation was determined as ε ̇=[sinh(0.006388σ)]^12.123∙exp⁡(37.7505-287.141/RT). The microstructural evolution of the alloy during deformation at 400oC revealed the presence of both slip and shear bands in the grains. At 700oC, dynamic recrystallization grains were observed but recrystallization was incomplete. In sum, these results provided the theoretical basis for continuous extrusion process of alloys with promising future use.

A typical river-connected lake, Jinshan Lake, was selected as the study area. By the combination of field experiment, laboratory experiment and mathematical model, we plotted the relationship between the concentration of DCu-SCu and FDI, and constructed the mathematical model of the migration and transformation of HMCu in Jinshan Lake. We choose a typical diurnal tide to simulate and revealed the vertical migration characteristics of HMCu in Jinshan Lake during a diurnal tide. The results show that: (1) The release rate of DCu was proportional to FDI and background content, respectively. (2) Due to the nearby industrial enterprises and terrain characteristics, SA loads the most HMCu, the average concentration is 70.07mg/kg. According to the characteristics and geographical location of LC, the concentration of copper in the two states fluctuates greatly (DCu: 43.20~74.77 mg/kg, SCu: 53.63~74.67mg/kg). The fluctuation trend of SCu in ZA is significantly different from that in other areas, which mainly due to the complex hydraulic distribution and the sorption-desorption process of HMs in sediment particles. The hydraulic disturbance of JG is the least and relatively stable, which is the farthest from the inlet of the lake and is the least affected by the Yangtze river. (3) The FDI in a diurnal tide reaches the suspension condition of fine sediment particles in each region. FDI and sediment concentration on the vertical exchange of two - state Cu is significant.

In order to understand the hot deformation behavior of novel Cu/Al laminated composites, isothermal hot compression tests were conducted by Gleeble-1500D thermo-mechanical simulator. And the effect of bonding interface, deformation temperature and strain rate on the deformation behavior was analyzed. Results show that under the interface constraint effect, soft Al layer trends to flow synchronously with hard Cu layer. And further microstructure examinations indicate the cooperative deformation capability of Cu/Al composites increases with increasing stain rate and decreasing deformation temperature. Strain hardening exponent, calculated based on the true stress-true strain data, also proves the effect of deformation temperature and strain rate on the cooperative deformation behavior. Meanwhile, unique composites structure allows the Al matrix to exhibit the characteristic of dynamic recrystallization during the hot deformation process. Lastly, strain compensated Arrhenius-type constitutive equation was employed to describe the coupling effect of temperature, strain rate and strain on the flow stress.

The activity and cyclability of Cu-MOF-74 as catalyst was studied for the ligand-free C-O cross-coupling reaction of 4-nitrobenzaldehyde (NB) with phenol (Ph) to form 4-formyldiphenyl ether (FDE). Cu-MOF-74 is characterized by unsaturated copper sites in a highly porous metal-organic framework. The influence of solvent, reaction temperature, NB/Ph ratio, catalyst concentration and basic agent (type and concentration) were evaluated. High conversions were achieved at 120°C, 5 mol% of catalyst, NB/Ph ratio of 1:2, DMF as solvent and 1 equivalent of K2CO3 base. The activity of Cu-MOF-74 material was higher than other ligand-free copper catalytic systems tested in this study. This catalyst was easily separated and reused in five successive runs, achieving a remarkable performance without significant porous framework degradation. The leaching of copper species in the reaction medium was negligible. The O-arylation between NB and Ph took place only in the presence of Cu-MOF-74 material, being negligible without the solid catalyst.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

Much attention has been attracted by aqueous zinc zinc-ion batteries (AZIBs) due to the features of inherent safety, environmental compatibility, low cost and fantastic energy density. Nevertheless, chemical corrosion and dendrite growth occurring on Zn anode during the charge/discharge process usually cause the surface passivation and short circuit of cells, seriously hindering the development of AZIBs. To settle these problems, a Cu(II)/polydopamine modified glass fiber (Cu-PDA/GF) is designed as separator. Due to the enhanced ionic conductivity of Cu(II) and PDA modified glass fiber separator, reversible zinc plating/striping is achieved in symmetric cells, which display long cycle life of over 1800 h at the current density of 1 mA cm−2 with the fixed capacity of 1 mAh cm−2. Moreover, the assembled Zn//V2O5 cells using Cu-PDA/GF separator also demonstrate improved capacity retention. The present study provides a simple separator modification strategy for high-performance and reliable AZIBs, which are conducive to energy storage devices.

Fe rich soft magnetic alloys are candidates for applications as magnetic sensors and actuators. These alloys can also be added to hard magnetic compounds to obtain spring magnets. In this work we produce two nanocrystalline Fe-Zr-B-Cu alloys by the powder metallurgy powder technology of mechanical alloying. The increase of the boron content favors the reduction of the crystalline size. Thermal analysis (by differential scanning calorimetry) shows at temperatures between 450 and 650 K wide exothermic processes, associated with the relaxation of tensions of the alloys produced by milling. At high temperatures, a main crystallization peak is found. The apparent activation of this process was determined by Kissinger and isoconversional methods. The values are compared with those found in the scientific literature. Likewise, adapted thermogravimetry permits to determine the Curie temperature. The functional response has been analyzed by hysteresis loop cycles. According to the composition, the decrease of the Fe/B ratio diminishes the magnetic soft behavior.

To enhance the mechanical properties (i.e. strength and elongation) of the face-centered cubic (fcc) α-phase in the Au-Cu-Al system, this study focused on the introduction of the martensite phase (doubled B19 (DB19) crystal structure of Au2CuAl) via the manipulation of alloy compositions. Fundamental evaluations, such as microstructure observations, phase identifications, thermal analysis, tensile behavior examinations, and reflectance analysis have been conducted. The presence of fcc annealing twins was both observed in the optical microscope (OM) and the scanning electron microscope (SEM) images. Both the strength and elongation of the alloys were greatly promoted while the DB19 martensite phase was introduced into the alloys. Amongst all the prepared specimens, the 47Au41Cu12Al and the 44Au44Cu12Al alloys performed the optimized mechanical properties. The enhancement of strength and ductility in these 2 alloys was achieved while the stress plateau was observed during the tensile deformation. A plot of the ultimate tensile strength (UTS) against fracture strain was constructed to illustrate the effects of the introduction of the DB19 martensite phase on the mechanical properties of the alloys. Regardless of the manipulation of the alloy compositions and the introduction of the DB19 martensite phase, the reflectance stayed almost identical to pure Au.

Light alloys machining is a widely implemented process that have usually used in presence of cutting fluids to reduce the wear impact and increase tool life. However, current environmental protection policies require their elimination in order to improve process sustainability. This fact forces to work under aggressive cutting conditions, producing adhesion wear that affects the integrity of the part surface. This study describes cutting tool wear mechanisms in machining of UNS A92024 samples under dry cutting conditions. EDS analysis showed the different composition of the adhered layers, while roughness was also positively affected by the change of the cutting geometry produced in the tool.

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

The catalytic decomposition of methane (CDM) process produces hydrogen in a single stage and avoids the CO₂ emission thanks to the formation of high added value carbon nanofilaments as by-product. In this work, Ni monometallic and Ni-Co, Ni-Cu and Ni-Fe bimetallic catalysts are tested in the CDM reaction for the obtention of fishbone carbon nanofibers (CNF). Catalysts, in which Al₂O₃ is used as textural promoter in their formulation, are based on Ni as main active phase for the carbon formation and on Co, Cu or Fe as dopants in order to obtain alloys with an improved catalytic behaviour. Characterization of bimetallic catalysts showed the formation of particles of Ni alloys with a bimodal size distribution. For the doping content studied (5 mol. %), only Cu formed an alloy with a lattice constant high enough to be able to favor the carbon diffusion through the catalytic particle against surface diffusion, resulting in higher carbon formations, longer activity times and activity at 750 °C, where Ni, Ni-Co and Ni-Fe catalysts were inactive. On the other hand, Fe also improved the undoped catalyst performance presenting a higher carbon formation at 700 °C and the obtention of narrow carbon nanofilaments from active Ni₃Fe crystallites.

This study investigated the fatigue properties and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar welded joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Meanwhile, the fatigue life of 14 kV joints was one order of magnitude higher than that of 12 kV. The SEM observation on the fatigue fracture surface shows that the typical “tire-mark” fatigue striation just appeared on the 14 kV joint, indicating higher ductility for handling more extended plastic deformation. The high EBSD acquisition was achieved except for the transition zone due to the formation of ultra-fine nanocrystalline Al2Cu phase and amorphous phase, along with many dislocations. Dense low-angle grain boundaries (LAGBs) and refined grains are formed along the bonding interface. This indicates that severe plastic deformation induced dislocations to form the substructure in such an instant (40-60 μs) during the high-velocity collision. The interfacial strength is not only due to the continuous interfacial diffusion layer with a “wave-like” or “inverted hook-like” pattern but also benefits from refined grains along the interface and in the transition zone, as well as the hybrid amorphous-nanocrystalline microstructure, which strengthens the joint through increasing ductility induced by refined grains and regulating amorphous or nanocrystalline phases to affect the balance between strength and ductility of the Al/Cu joint.

Melting, solidification and viscosity properties of a multicomponent Fe-Cu-Nb-Mo-Si-B alloys with low aluminum addition up to 0.42 at.% Al were studied using an oscillating cup viscometer. It is shown that melting and solidification are divided into two stages with a knee point at 1461 K. The temperature dependences of the liquid fraction between the liquidus and solidus temperatures during melting and solidification are calculated. It has been proven that aluminum accelerates the processes of melting and solidification and leads to an increase in liquidus and solidus temperatures. In the liquid state at temperatures above 1700 K in an alloy with a low aluminum content, the activation energy of viscous flow increases. This growth was associated with the liquid – liquid structure transition caused by the formation of large clusters based on the metastable Fe23B6 phase. Aluminum atoms attract iron and boron atoms and contribute to the formation of clusters based on the Fe2AlB2 phase and metastable phases of a higher order.

The effects of various drawing parameters and annealing processes on the structure and properties of Cu-Ag wires, containing 1 wt% silver, were investigated using specialized equipment including fine wire drawing machines, very fine wire drawing machines, heat treatment equipment, tensile testing machines, microcomputer-controlled electronic universal testers, resistance testers, and scanning electron microscopes. The results revealed that continuous drawing of Cu-1%Ag alloy wires led to elongation of the grains, resulting in a uniform and tightly fibrous microstructure. Moreover, the tensile strength of the alloy wire increased from 670 MPa to 783.9 MPa after a single-pass with a deformation of 14%. Subsequently, when the wire was drawn at a speed of 500 m/min, the tensile strength further increased to 820.1 MPa. After annealing the Փ0.08 mm Cu-1% Ag alloy wire, an increase in annealing temperature up to 500°C resulted in the wire's tensile strength decreasing from 820.1 MPa to 377.5 MPa. Simultaneously, the elongation increased from 1.94% to 15.21%, and the resistivity decreased from 1.931×10-8Ω·m to 1.723×10-8Ω·m. Additionally, when annealing was conducted at a rate of 80 m/min, the wire resistivity dropped to 1.635×10-8Ω·m.

The integration of metal nanoparticles and solid carriers can achieve ideal stability, high load and good conductivity. In this work, copper nanoparticles (Cu NPs) were sequentially deposited on a cobalt metal-organic framework (Co-MOF) by bonding with exposed imino groups, followed by a reduction reaction to prepare a new Cu@Co-MOF composite. Cu@Co-MOF acts as a non-enzymatic electrochemical sensor to detect glucose (Glu) in an alkaline medium. The composite working electrode of Cu@Co-MOF/GCE (GCE = glassy carbon electrode) improves the electrocatalytic activity for Glu oxidation. Cu@Co-MOF/GCE shows excellent electrocatalytic performances in Glu concentration ranging 0.005~1.8 mmol∙L⁻¹ (mM): the sensitivities are 282.89 μA∙mM⁻¹∙cm⁻² in 0.005-0.4 mM Glu and 113.15 μA∙mM⁻¹∙cm⁻² in 0.4-1.8 mM Glu respectively with low detection limit of 1.6 μM (S/N = 3) and high selectivity and stability.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

This work reports the influence of reduced graphene oxide (rGO) support on the catalytic performance of Cu@PtRu/rGO catalysts towards methanol oxidation in acidic medium. These core-shell catalysts are synthesized by the reduction method in two steps being the first using ethylene glycol to obtain Cu/rGO and the second, the reduction of copper atoms synthesized in the previous step to produce Cu@PtRu/rGO. In order to compare the catalytic performance of the prepared catalysts, Pt/C, PtRu/C, Cu@PtRu/C catalysts are also synthesized on Vulcan XC-72R carbon. The theoretical loading of Pt used in the Vulcan XC-72R carbon supported catalysts is equal to that utilized in Cu@PtRu/rGO, and higher in the other prepared catalysts. The surface composition of the nanoparticles, as well as their sizes, particle size distribution and morphology of the catalyst particles are characterized by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Cyclic voltammetry (CV) and chronoamperometry (CA) are employed to measure the electrochemical performance of the prepared catalysts. The anodic scans show that for the region of technological interest (0.1 to 0.4 V), the Cu@PtRu/rGO-16 electrocatalyst exhibits higher current density value than the others as a result of its lower starting oxidation potential (0.250V against 0.437V for Pt/C) and its higher ratio between forward (iF) and reverse (iR) current densities (iF/iR 1.45 against 0.93 for Pt/C). Chronoamperometric tests depict that the current density value of Cu@PtRu/rGO-16 catalyst is about 4 times higher than that of Cu@PtRu/C-16 and Cu@PtRu/C-18 catalysts, ca. 4.8 times higher than that of PtRu/C-30 catalyst and around 6 times higher than that of Pt/C-30. These results suggest that Cu@PtRu/rGO-16 exhibits high bulk activity for the electrooxidation of methanol, high stability and high tolerance to CO poisoning, making it possible to reduce the platinum loading in proton exchange membrane fuel cells (PEMFCs).

In this work, the ternary titanium, copper and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by x-ray diffraction (XRD), nanoindentation (modulus and hardness) and Atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel.

Cu₆Sn₅ whiskers precipitated in Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer were found and investigated after reflow soldering and during aging. Ag₃Sn fibers can be observed around Cu₆Sn₅ whiskers in the matrix microstructure, which can play an active effect on the reliability of interconnection. Different morphologies of Cu₆Sn₅ whiskers can be observed, and hexagonal rod structure is the main morphology of Cu₆Sn₅ whiskers. A hollow structure can be observed in hexagonal Cu₆Sn₅ whiskers, and a screw dislocation mechanism was used to represent the Cu₆Sn₅ growth. Based on mechanical property testing and finite element simulation, Cu₆Sn₅ whiskers were regarded as having a negative effect on the durability of Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer.

Heavy metals constitute pollutants particularly common in air, water, and soil. They are present in both urban and rural environments, on land and in marine ecosystems, causing serious environmental problems since they do not degrade easily, remain almost unchanged for long periods, and bioaccumulate. Detection, though especially quantification, is a systematic process as monitoring of their levels needs to be carried out at regular intervals since there is often seasonal variation. The need for rapid and low-cost determination of metals is therefore considerable. In the present study atomic absorption spectroscopy (AAS), using a flame or graphite furnace, and square wave anodic stripping voltammetry (SWASV), using a bismuth thin film electrode, a sensitive voltammetric method is being compared and analytically validated. Atomic absorption spectroscopy (AAS) represents a well-established analytical technique while anodic stripping voltammetry is being criticized for its applicability in complicated sample matrices such as soil samples. This sample-handling challenge is being investigated in the present study. The results show that both methods AAS and ASV were satisfactorily correlated and showed that the concentration of metals is lower than the limit values, but with increasing trend. Therefore, continuous monitoring of metal levels in the urban complex of the city is necessary and a matter of great importance. Regarding Cd, the detection limits of Cd are lower compared to those of AAS when using the graphite furnace, while an overestimation was noted when using flame-AAS in comparison with those found with SWASV. The SWASV method has the advantage of being cheaper and faster, enabling the simultaneous determination of heavy elements across the range of concentrations that these elements can occur in Mediterranean soils. Additionally, we applied a dsDNA-modified electrode which can be used in the speciation analysis of Cu(I) and Cu(II). The changes in the characteristic peaks of guanine and adenine can be applied in the redox speciation analysis of copper in soil which represents an issue of great importance.

In this study, the effects of combined addition of CeLa and GdY on microstructure and mechanical properties of as-cast Al-4Cu-1Mn alloys were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopies (TEM) and tensile testing. The results show that the minor addition of CeLa and GdY leads to the refinement of grain size. The addition of CeLa results in the formation of supersaturated vacancies in the Al matrix, whereas the addition of GdY leads to a decrease in the precipitation temperature of the Al2Cu phase. The combined CeLa and GdY addition can significantly increase ultimate tensile strength (UTS) while losing only a small amount of elongation (EL). Compared with the unmodified alloy, the grain size and SDAS of the alloy (0.2 wt% CeLa + 0.1 wt% GdY) were diminished by 67.2% and 58.7%, respectively, while maximum hardness and UTS rose by 31.2% and 36.9%, correspondingly.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

[Co(AMPY)(DAPY)Cl2(H2O)].H2O (1) [Cu(AMPY)(DAPY)Cl2(H2O)].H2O (2) [Zn(AMPY)(DAPY)Cl2(H2O)] (3) were prepared from the ligands; AMPY = 2-amino-4-methylpyrimidine (L1), DAPY = 2,3-diaminopyridine (L2) and CoCl2.6H2O, CuCl2.2H2O and ZnCl2 in water/ethanol solutions and the three products characterized by elemental analysis, ultraviolet-visible spectroscopy (UV–Vis), Fourier-transform infrared spectroscopy (FT-IR), magnetic susceptibility, molar conductivity methods, and TGA analysis. The X-ray powder diffraction of the Co(II), Cu(II), and Zn(II) compounds showed that the geometry of monoclinic and SEM analysis revealed their morphology with a smooth surface. Molecular modeling was performed for all compounds using the density functional method DFT/B3LYP to study the structures and the frontier molecular orbitals (HOMO and LUMO). We have used Gaussian09 software for the calculations. In this study, different complexes were tested against Gram negative and Gram positive bacterial species to give insight into their broad-spectrum effects. The used pathogenic strains were two Gram positive species "Staphylococcus aureus and Micrococcus luteus" and two Gram negative species "Salmonella thyphimurium and Escherichia coli. The antifungal activity was evaluated against a pathogenic reference strain of the yeast Candida albicans. The antimicrobial and antioxidant assay results demonstrate that the tested compounds are effective against Gram positive and negative bacteria. Additionally, the compounds have an antifungal effect against Candida albicans with a maximum inhibitory zone of 2.5cm. The results demonstrated high antioxidant potential for the Zn(II) complex with a DPPH scavenging of 91.5%, however, the Cu(II) complex was low (16.5%). The data of docking with tyrosyl-tRNA synthetase presented that all compounds fit very well in the catalytic pockets of the proteins of the receptor.

The effect of transition metal substitution for Fe and the structural and magnetic properties of Gd2Fe16Ga0.5TM0.5 (TM=Cr, Mn, Co, Ni, Cu, and Zn) compounds were investigated. Rietveld analysis of X-ray diffraction indicates that all the samples crystallize in the hexagonal Th2Ni17 structure. The lattice parameters: a, c and unit cell volume show TM ionic radii dependence. Both Ga and TM atoms show preferred site occupancy for 12j and 12k sites. The saturation magnetization at maximum room temperature was observed for Co, Ni, and Cu of 69, 73, and 77 emu/g, respectively while minimum value was observed for Zn (62emu/g) doping Gd2Fe16Ga0.5TM0.5. Highest Curie temperature of 590 K was observed for Cu doping which is 15% and 5% and thesehigher than Gd2Fe17 and Gd2Fe16Ga compounds, respectively. The hyperfine parameters viz. hyperfine field and isomer shift, show systematic dependence on the TM atomic number. The observed magnetic and Curie temperature behavior in Gd2Fe16Ga0.5TM0.5 is explained on the basis of Fe(3d)-TM(3d) hybridization. The superior Curie temperature and magnetization value of Co, Ni, and Cu doped Gd2Fe16Ga0.5TM0.5 compounds as compared to pure Gd2Fe17 or Gd2Fe16Ga makes Gd2Fe16Ga0.5TM0.5 a potential candidate for high-temperature industrial magnet applications.

Successful geophysical exploration works in Gucheng-Yaxi area located in Gaochun District, Jiangsu province, China, have been limited partly due to complex geological condition of the area and high artificial noise in data acquired using electrical and electromagnetic methods. In this work, we deployed the new anti-interference spread spectrum induced polarization method (SSIP) and audio magnetotellurics (AMT) method to detect a copper-polymetallic deposit in the area. Two-dimensional (2D) inversion results at Gucheng-Yaxi Area revealed a high chargeability anomalous zone on SSIP profile that coincided with a zone of moderate resistivity located between two resistor bodies on AMT profile. A follow up 1200 meters drill hole was established at this high chargeability-moderate resistivity zone which encountered polymetallic (copper, lead, zinc, gold and silver) mineralization at the depth ≥ 400 m. Drill hole data analysis showed that mineralization occurs interspaced in marble rock mass at varies depth. Furthermore, several low resistivity-weak chargeability sections were revealed and inferred attributed to Cretaceous sediments and faults. These faults are thought to have played critical role in the polymetallic mineralization genesis. In summary, this work demonstrated the successful of application of SSIP and AMT at detecting a metallic deposit in an area with high artificial noise. Hence the geophysical prospection potential of Gucheng-Yaxi area is great.

Monometallic (Ni, Co, Cu) and bimetallic (Ni-Co, Ni-Cu) 10-20 wt. % metal containing catalysts supported on fly ash zeolite were prepared by post-synthesis impregnation method. The catalysts were characterized by X-ray powder diffraction, N2 physisorption, XPS and H2-TPR methods. Finely dispersed metal oxides and mixed oxides were detected after the decomposition of impregnating salt on the relevant zeolite support. By reduction intermetallic, NiCo and NiCu phases were identified in the bimetallic catalysts. Hydrogeoxygenation of lignocellulosic biomass-derived levulinic acid to γ-valerolactone (GVL) was studied. Bimetallic, 10 wt. % Ni, 10 wt. % Cu or Co containing fly ash zeolite catalyst showed higher catalytic activity than monometallic ones. Their selectivity to GVL reached 70-85 % at 100 % conversion. The reaction proceeds through formation of 4-hydroxy pentanoic acid, as the only intermediate compound.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

The detection of toxic heavy metals, especially cadmium (Cd), lead (Pb), zinc (Zn), copper (Cu), is a global problem due to ongoing pollution incidents and continuous anthropogenic and industrial activities. Therefore, it is important to develop effective detection techniques to determine the levels of contamination from heavy metals in various media. Electrochemical techniques and more specifically, voltammetry, due to its properties, is a promising method for the simultaneous detection of heavy metals. This review examines current trends related to electrode formation and analysis techniques used. In addition, there is a reference to advanced detection methods based on nanoparticles developed so far, as well as formation with bismuth and the emerging technique of screen printed electrodes. Finally, the advantages of using these methods are highlighted, while a discussion is made on the benefits arising from nanotechnology, as it gives the researcher a new idea for integrating these technologies into devices that can be used anywhere and anytime.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

Magnetic pulse welding (MPW) employs high pulsed magnetic field to accelerate parts against each other thus forming an impact joining. Single-turn tool coils and field-shapers (FS) used in MPW operate under the most demanding conditions: a magnetic field of 40-50 T with a period of tens of microseconds. For conventional copper and bronze coils intense thermo-mechanical stresses lead to rapid degradation of the working bore. This work is aimed to improve the efficiency of field-shapers and focused on development of 2- and 4-slit FS with nanocomposite Cu 18Nb wire brazed as FS inner current-carrying layer. The measured ratio of magnetic field to discharge current was 56.3 and 50.6 T/MA for 2- and 4-slit FS respectively. FEM calculations of magnetic field generation showed its 6-9% and 3% variation for 2- and 4-slit FS respectively. The results of copper tube compression have shown an ovality of 27% and 7% for 2- and 4-slit FS respectively. The measured deviation of weld joining length was 11% and 1.4% in 2- and 4-slit FS respectively. Compared to the previous experiments on the whole steel inductor, the novel FS showed significantly better results in terms of efficiency and homogeneity of the magnetic field.

Abstract: Circuit breakers are affected by multiple lightning strikes after the breaker has been tripped and can break down again, which will reduce the life of the circuit breaker and threaten the stable operation of the power system. Aiming at this problem, the paper obtained the temperature diffusion process of the inrush current process of circuit breaker opening and breaking through the schlieren technique, and combined with the existing image recognition technology to obtain the temperature characteristics of the airflow in the air gap of the contact, and the characteristics of the airflow flow. The results of the study show that the circuit breaker breakdown process generates a shock wave with a velocity approximately equal to the speed of sound under the same conditions. The maximum velocity of the airflow boundary diffusion is about 1/4 of the speed of sound under the same condition, and it decays very fast, reducing to the airflow drift velocity within 10ms after breakdown. The maximum temperature of the thermals is concentrated between 6000 and 8000 K and the temperature change is approximately inversely proportional to the square of time. The research provides the basis for the design of circuit breaker contact structure, opening speed optimization method, interrupter chamber and insulation design optimization.

The photocatalytic biohydrogen generation using ZnO with the aid of simultaneous deposition of copper from an aqueous biomass-derivative glycerol solution was investigated. The effects of concentration of glycerol solution, Cu ion concentration and reaction temperature on biohydrogen generation were investigated. The photocatalytic biohydrogen production rate increased with increasing the concentration of aqueous glycerol solution, and the observed data could be fitted to the Langmuire-Hinshelwood kinetic models. The photocatalytic H2 production efficiency with ZnO could be significantly improved by simultaneous Cu deposition. The photocatalytic biohydrogen production rate was dependent on temperature, and increased with the increasing temperature. The possible mechanisms for oxidation of glycerol solution and photocatalytic hydrogen generation were proposed.

We propose a novel electrochemical system to form precipitation patterns of Cu-Fe-based Prussian blue analogues (Cu-Fe PBA) in agarose gels, using an applied voltage to produce reactant ions. The spatiotemporal evolution, spatial distribution, and crystallite morphologies of the precipitates were investigated by visual inspection, Fe Kα intensity distribution measurements, and optical and scanning electron microscope observations. The precipitation patterns and their evolution depended on the applied voltage. Multicolored periodic precipitation bands were stochastically formed under cyclic alternating voltage (4 V for 1 h and then 1 V for 4 h per cycle). The distances between adjacent bands were randomly distributed (0.30 ± 0.25 mm). The sizes and shapes of the crystallites generated in the gel were position-dependent. Almost cubic but fairly irregular crystallites (0.1–0.8 μm) were formed in the periodic bands, whereas definitely cube-shaped crystallites (1–3 μm) appeared close to the anode. These cube-like reddish-brown crystallites were assigned to Cu-FeII PBA. In some periodic bands, plate-like blue crystallites (assigned to Cu(OH)2) were also present. Future issues for applications of the observed periodic banding were discussed.

A novel gas-phase electrocatalytic system based on a low-temperature proton exchange membrane (Sterion) was developed for the gas phase electrocatalytic conversion of CO2 to liquid fuels. This system achieved gas-phase electrocatalytic reduction of CO2 at low temperatures (below 90 ºC) over a Cu cathode by using water electrolysis-derived protons generated in-situ on an IrO2 anode. Three Cu-based cathodes with varying metal particle sizes were prepared by supporting this metal on an activated carbon at three loadings (50, 20, and 10 wt%; 50%Cu-AC, 20%Cu-AC, and 10%Cu-AC, respectively). The cathodes were characterized by N2 adsorption–desorption, temperature-programmed reduction (TPR), and X-ray diffraction (XRD) whereas their performance towards the electrocatalytic conversion of CO2 was subsequently studied. The membrane electrode assembly (MEA) containing the cathode with the largest Cu particle size (50%Cu-AC, 40 nm) showed the highest CO2 electrocatalytic activity per mole of Cu, with methyl formate being the main product. This higher electrocatalytic activity was attributed to the lower Cu–CO bonding strength over large Cu particles. Different product distributions were obtained over 20%Cu-AC and 10%Cu-AC, with acetaldehyde and methanol being the main reaction products, respectively. The CO2 consumption rate increased with the applied current and the reaction temperature.

At room temperature, the indentation morphologies of crystalline copper with different grain size including nanocrystalline (NC), ultrafine-grained (UFG) and coarse-grained (CG) copper were studied by nanoindentation at the strain rate of 0.04/s without holding time at indentation depth of 2000 nm. As the grain size increasing, the height of the pile-up around the residual indentation increases and then has a slightly decrease in the CG Cu, While the area of the pile-up increases constantly. Our analysis has revealed that the dislocation motion and GB activities in the NC Cu, some cross- and multiple-slips dislocation insides the larger grain in the UFG Cu, and forest dislocations from the intragranular Frank-Read sources in the CG Cu, would directly induce these distinct pile-up effect.

The primary objective of this study is to synthesize, elucidate the structural properties, and ex-plore the biological activity of novel metal complexes derived from 6-methyl-2-thiouracil and 6-propyl-2-thiouracil. The paper outlines a synthesis method and assesses the antimicrobial activ-ity of newly formed Cu(II) and Pd(II) complexes with two substituted 2-thiouracil ligands. The structural attributes of these newly developed compounds are thoroughly discussed based on data derived from melting point analysis, MP-AES for Cu and Pd, UV-Vis, IR, ATR, 1H NMR, 13C NMR and Raman spectroscopy. The interpretation of the complex spectra is assisted by the data for 6-methyl-2-thiouracil and 6-propyl-2-thiouracil obtained from 1H-1H COSY, DEPT-135, HMBC and HMQC spectra. In addition, the antimicrobial activity of these complexes and the free ligands are assessed against both Gram-positive and Gram-negative bacteria, as well as yeasts.

Heusler Ni-Mn-Ga alloys with martensitic transformation being multiferroic materials are touted for magneto- and multi-caloric effect (MCE) and moreover, they exhibit magnetic shape memory (MSM) phenomena. MCE benefits from high saturation magnetization and also large variability and sensitivity of transformation temperatures on alloying. In contrast, MSM phenomena are limited by low temperatures of both ferromagnetic and ferroelastic transformations. In an attempt to increase the transformation temperatures and to understand the physical fundamentals beyond transformation variations and magnetic ordering, we experimentally investigate the magnetic and transformation properties in Ni2MnGa alloyed with transitional elements spanning from Cr to Cu. These elements are consecutively substituted on Ni, Mn, and Ga sites, to establish the effect of positional substitution and elemental evolution. The elemental dependence of saturation magnetization, magnetocrystalline anisotropy, Curie temperature, and martensitic transformation temperatures are compared with (non-)stoichiometric Ni-Mn-Ga Heusler compounds. The observed behavior is complex and there are no clear trends of transformation temperatures as a function of the number of valence (non-bonding) electrons per atom, however, the saturation magnetization at 10K and Curie temperature seems to follow the Pauli-Slater curve. Obtained results can serve as useful rectification for the theoretical prediction of new Ni-Mn-Ga-X Heusler alloys.

Copper indium gallium diselenide, Cu(In,Ga)Se2, thin-film of about 1.2 μm has been deposited on Mo coated soda lime glass by thermal co-evaporation of Cu, In, Ga, and Se sources. The thin film CIGS was characterized by energy dispersive spectroscopy (EDS) and identified the elemental composition of Cu, In, Ga and Se in the film. A CIGS device was completed by the successive deposition of multiple layers; SLG/Mo/CIGS/CdS/ZnO/ITO which yielded the efficiency of 11%. External spectroscopic ellipsometry (ex-situ SE) was performed on the completed device and the device analysis was performed. Starting with the parameterized complex dielectric functions of the individual component layers, SE analysis was performed using a step-wise procedure that ranks the fitting parameters according to their ability to reduce the mean square error (MSE) of the fit. The resulting layer thicknesses and dielectric functions were used to simulate the external quantum efficiency (EQE) of the device assuming complete active layer collection. Electronic losses were identified by comparison of simulated EQE with the measured EQE. The ultimate goal of this work is the optimization of narrow band-gap CIGS-related solar cells for the bottom layer in tandem devices.

Classical antibacterial drugs were designed to target specific bacterial properties distinct from host human cells to maximize potency and selectivity. These designs were quite effective as they could be easily derivatized to bear next generation drugs. However, the rapid mutation of bacteria and their associated acquired drug resistance have led to the rise of highly pathogenic superbug bacterial strains for which treatment with first line drugs is no match. More than ever, there is a dire need for antibacterial drug design that goes beyond conventional standards. Taking inspiration by the body’s innate immune response to employ its own supply of labile copper ions in a toxic attack against pathogenic bacteria, which have a very low Cu tolerance, this review article examines the feasibility of Cu-centric strategies for antibacterial preventative and therapeutic applications. Promising results are shown for the use of Cu-containing materials in the hospital setting to minimize patient bacterial infections. Studies directed at disrupting bacterial Cu regulatory pathways elucidate new drug targets that can enable toxic increase of Cu levels and perturb bacterial dependence on iron. Likewise, Cu intracellular chelation/prochelation strategies effectively induce bacterial Cu toxicity. Cu-based small molecules and nanoparticles demonstrate the importance of the Cu ions in their mechanism and display potential synergism with classical drugs.

The efficiency of a new composite material of the layered double hydroxide (LDH) of ZnMgAl and rice husk biochar (RHB) for the removal of Cu(II) and Pb(II) ions from synthetic wastewater was investigated in this study. The images of scanning electron microscope showed extremely fine crystalline LDH particles decorated on the rough surface of the RHB while the succesful formation of the composite adsorbent (LDH/RHB) was confirmed by the corresponding energy dispersive X-ray and the Fourier-transform infrared spectroscopy. An equilibrium contact time of 30 and 15 min for Cu2+ and Pb2+, respectively, was proposed for the optimum performance of the batch adsorption process. The dose of the LDH/RHB adsorbent was optimized at 0.4 g yielding maximum adsorption capacities of 117 and 124 mg g-1 for Cu2+ and Pb2+, respectively, with corresponding maximum removal efficiencies of nearly 94% and 99%. The initial meta concentrations was optimized at 50 or 60 mg L-1 corresponding to maximum removal efficiencies or adsorption capacities. For the changing initial metal’s concentration, the removal efficiencies remained unchanged for up to 50 mg L-1 and decreased by about 50% by increasing the initial concentrations from 50 to 100 mg L-1. The adsorption capacities observed a linear increasing trend by increasing the initial concentrations from 5 to 60 mg L-1 and remained unchanged afterward up to 100 mg L-1. A solution pH of 6.0 yielded optimum results with an increasing trend in adsorption capacities and percentage removal by changing the solution pH from 2.0 to 7.0. Based on the best-fit of the pseudo second-order kinetic model to the experimental data, the chemisorption was suggested to be the controlling mechanism of adsorption. The fitting of the Langmuir model suggested a monolayer sorption of Cu2+ and Pb2+ in addition to a heterogeneous adsorption as supported by the fitting of the Temkin isotherm. The application of the Dubinin–Radushkevich isotherm proposed a physical adsorption (mean free energy of adsorption less than 8 kJ mol−1) of both heavy metal ions on the surface of the LDH/RHB adsorbent.

The corrosion behavior of Fe-containing directionally solidified (DS) and centrifugally cast (CC) Al-Si-Cu-Zn alloys with either Co or Ni additions has been investigated. Electrochemical and immersion corrosion methods were used to investigate the corrosion behavior in 0.6 M NaCl after short (1-hour) and long (30-day) exposure periods. The employed solidification methods allowed the production of samples with a wide range of secondary dendrite arm spacing (SDAS) while preserving Si and Fe-containing phases. The 0.5 wt.% Ni and Co additions led to the growth of the AlFeSi(Ni) and AlFeSi(Co) phases, but no binary AlNi nor AlCo intermetallic par-ticles have been generated. Potentiodynamic polarization studies at early exposure revealed an increase in the corrosion potential as the Ni was added for either fast or slow solidified samples. The electrochemical impedance spectroscopy at early exposure demonstrated that the Ni-modified alloy, on the other hand, was associated to smaller charge transfer resistances, in-dicating a reduction in corrosion resistance after short elapsed time into the electrolyte. Howev-er, 30-day immersion tests revealed much lower corrosion rate of the Ni-modified alloy than the other alloys, while the corrosion rates of the Co-modified and non-modified alloys were simi-lar. In the Ni-containing alloy, decreased corrosion rate under long-term corrosion process was attributed to the formation of a thick and dense alumina layer, effectively protecting the surface under such conditions. This work contributes to a better knowledge of the corrosion behavior of Ni- and Co-corrected Al industrial scrap compositions.

In the paper, the results of an investigation into trace elements found in slag sulphides from 14 archaeological Bronze Age settlements of the Cis-Urals, Trans-Urals and North and Central Kazakhstan are presented. The study used Cu-(Fe)-sulphides as indicator minerals. Cu-(Fe)-S minerals in slags are primarily represented by covellite and chalcocite, as well as by rarer bornite and single chalcopyrite grains. Slag sulphides formed relic clasts and neogenic droplets of different shapes and sizes. Supergenic ores in the Bronze Age in Urals and Kazakhstan played a significant role in the mineralogical raw material base. In sulphides, the main indicator elements Fe, Co, Ni, As, Se, Te, Sb, Ag, Pb, and Bi are important markers of copper deposit types. Sulphides from olivine Cr-rich spinel containing slags of Ustye, Turganik, and Kuzminkovskoe 2 are characterised by As-Co-Ni assemblages and confined to copper deposits in ultramafic rocks. Olivine sulphide-containing slags from Kamenny Ambar, Konoplyanka and Sarlybay 3 are characterised by Co-Se-Te assemblage and confined to mafic rocks. Glassy sulphide-containing slags from Katzbakh 6, Turganik, Ordynsky Ovrag, Ivanovskoe, Tokskoe, Bulanovskoe 2, Pokrovskoe, Rodnikovoe, and Taldysay are characterised by Ag-Pb-(Ba)-(Bi) assemblage and confined to cupriferous sandstone deposits. High As, Sb, Sn and Ba contents found in slags can be seen as indicators of alloying or flux components in primary copper smelting. These include samples from Ustye, Katzbakh 6, Rodnikovoe, and Taldysay sites, where high Ba and As slag contents are identified. The compilation of a database with a broad sample of sulphide compositions from Bronze Age slags and mines in the Urals and Kazakhstan will permit the further identification of ore types and raw materials associated with a particular deposit.

In this work, we report synthesis of Cu, Pt and Pd doped SnO₂ powders and their comparative CO gas sensing studies. Dopants were incorporated into SnO₂ nanostructures using chemical and impregnation methods by using urea and ammonia as precipitation agents. The synthesized samples were characterized using X-ray diffraction (XRD), Raman spectroscopy, Scanning electron microscopy (SEM) and High resolution transmission electron microscopy (HR-TEM). The presence of dopants within the SnO₂ nanostructures was evidenced from HR-TEM. Doped powders utilizing chemical methods with urea as precipitation agent presented higher sensitivities compared to the remaining, which is due to the formation of uniform and homogeneous particles resulted from the temperature assisted synthesis. The particle sizes of doped SnO₂ nanostructures were in the range of 40-100 nm. An enhanced sensitivity around 1783 was achieved with Cu doped SnO₂ when compared with two other dopants i.e., Pt (1200) and Pd: SnO₂(502). The high sensitivity of Cu: SnO₂ is due to formation of CuO and its excellent association and dissociation in the presence of CO with adsorbed atmospheric oxygen at sensor operation temperatures resulted in high conductance. Cu: SnO₂ may be an alternative and cost effective sensor for industrial applications.

The photophysical properties of Cu(II) complexes with 5,10,15,20-meso-tetrakis(phenyl)porphyrin and 5,10,15,20-meso-tetrakis(N-methylpyridium-4-yl)porphyrin were examined by luminescence and femtosecond time-resolved absorbance methods respectively. These studies were supported by DFT and TD-DFT calculations which highlight the important role played by a ligand-to-metal charge-transfer states in directing the system towards either intersystem crossing to the triplet hypersurface or coordinative expansion to a five-coordinate quasi-stable intermediate. The latter processes occurs when the porphyrin is photolyzed in the presence of suitably located Lewis bases. Femtosecond time resolved absorbance measurements on Cu(II)-5,10,15,20-meso-tetrakis(N-methylpyridium-4-yl)porphyrin confirm that the coordinative expansion in water occurs in approximately 700 fs while crossing to the triplet hypersurface takes approximately 140 fs in the same solvent. These processes are mutually exclusive, but both can occur simultaneously depending on the environment of the porphyrin. The ratio of the two processes depends on the relative orientation of the Lewis base with respect to the copper atom at the time of excitation. As a consequence, copper porphyrins such as these, are excellent probes to the environment of the porphyrin, and can be used to identify the location of the porphyrin when interacting with DNA fragments.

This study focuses on the analyses of nano-twinned Copper (Cu) films deposited through magnetron sputtering on Silicon Carbide (SiC) chips. The investigation encompasses the utilization of Chromium (Cr) adhesive layer coupled with varying voltage bias conditions. The goal is to comprehensively examine the influence of adhesive layer and negative bias voltages, contributing to an enhanced understanding of materials engineering and bonding technologies for advanced applications. The formation of a nanotwinned structure and (111) surface orientation can be properly controlled by applied substrate bias. High density nanotwinned structures were introduced into Cu films sputtered on SiC substrates with 82.3% of (111)-orientation proportion at -150 V much higher than the Cu film sputtered with another substrate bias. It is concluded that the sputtered Cu nanotwinned film formed with -150 V bias voltage has the potential to be employed as the interlayer for low temperature direct bonding.

In-situ nanoindentation experiment has been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiment in characterizing nonlinear material properties of 3D integrated microelectronic devices with through-silicon-vias (TSVs). The elastic, plastic, and interfacial fracture behavior of the copper via and matrix-via interface have been characterized using small scale specimens prepared with focused-ion-beam (FIB) and nanoindentation experiment. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7 to 83.7 degrees. The mixed-mode fracture strengths were extracted using the linear elastic fracture mechanics (LEFM) analysis and a fracture criterion was obtained by fitting the extracted data with the power-law function. The vectorial interfacial strength and toughness were found to be independent with mode-mix.

Porphyry copper-molybdenum deposits (PCDs) are the world’s most important source of copper, molybdenum and rhenium. Previous studies have reported that some PCDs can have sub-economic to economic grades of critical metals, i.e., those elements that are both essential for modern societies and subject to the risk of supply restriction (e.g., platinum group elements (PGE), rare earth elements (REE), In, Co, Te, Ge, Ga, among others). Even though some studies have reported measured concentrations of Pd and Pt in PCDs, their occurrence and mineralogical form remain poorly constrained. Furthermore, these reconnaissance studies have focused predominantly on porphyry Cu-Au deposits, but very limited information is available for porphyry Cu-Mo systems. In this contribution, we report the occurrence of critical metal (Pd, Pt, Au, Ag, and Te) inclusions in copper sulfides from the world’s largest PCD, the supergiant Río Blanco-Los Bronces deposit in central Chile. Field emission scanning electron microscope (FESEM) observations of chalcopyrite and bornite from the potassic alteration zone reveal the presence of micro- to nano-sized particles (<1-10 μm) of noble metals, most notably Pd, Au, and Ag. The high-resolution data show that these inclusions are mostly tellurides, such as merenskyite [PdTe2], Pd-rich hessite [Ag2Te], sylvanite [(Ag, Au)Te2] and petzite [Ag3AuTe2]. The data point to Pd (and probably Pt) partitioning in copper sulfides during the high-temperature potassic alteration stage, opening new avenues of research aimed at investigating not only the mobility of PGE during mineralization and partitioning into sulfides, but also at evaluating the potential of porphyry Cu-Mo deposits as a source for noble metals.

The microstructure evolution and grain refinement kinetics of a solution treated Cu – 0.1Cr – 0.06Zr alloy during equal channel angular pressing (ECAP) at a temperature of 673 K via route B_C were investigated. The microstructure change during plastic deformation was accompanied by the microband formation and an increase in the misorienations of strain-induced subboundaries. The refinement of initial coarse grains was considered as a result of continuous dynamic recrystallization. The dynamic recrystallization kinetics was discussed in terms of grain/subgrain boundary triple junction evolution. The strain dependence of the triple junctions of high-angle boundaries can be expressed by a modified Johnson-Mehl-Avrami-Kolmogorov relationship with a strain exponent of about 1.49. Severe plastic deformation by ECAP led to substantial strengthening of the Cu-0.1Cr-0.06Zr alloy. The yield strength increased from 60 MPa in the initial state to 445 MPa after the total strain of 12.

Two new coordination compounds of Mn(II) and Cu(II) viz. [Mn(bz)2(Hdmpz)2(H2O)] (1) and [Cu(crot)2(Hdmpz)2] (2) (where, bz = benzoate, crot = crotonate, Hdmpz = 3, 5-dimethyl pyrazole) have been synthesized and characterized using single crystal X-ray diffraction technique, FT-IR, electronic spectroscopy, TGA and elemental analyses. Compounds 1 and 2 crystallize as mono-nuclear coordination compounds of Hdmpz based penta-coordinated Mn(II) and hexa-coordinated Cu(II) respectively containing distorted trigonal bipyramidal and distorted octahedral geome-tries. Crystal structure analysis of compound 1 reveals the presence C‒H⋯π and π-stacking in-teractions along with O‒H⋯O, N‒H⋯O and C‒H⋯O H-bonding interactions which stabilizes the layered assembly of the compound. Similarly, the presence of hydrogen bonding along with π-stacking interactions stabilizes the crystal structure of compound 2. We have carried out theo-retical investigations to analyze π⋯π H-bonding and antiparallel CH···π non-covalent interac-tions observed in the compounds. DFT calculations were performed to evaluate strength of these interactions energetically. Moreover, QTAIM and non-covalent interaction (NCI) plot index computational tool were used to characterize them and evaluate the contribution of the H-bonds.

Pollutants accumulate in aquatic habitats as a result of mining activities. Lemna gibba and Lemna minor were used in this study to examine the accumulation capacities of Mo+, Pb+, and Cu++ in the acid fluids of the copper mining. Duckweed family includes water plants like L. minor and L. gibba. These are tiny, delicate, free-floating aquatic plants. Two reactors were assigned to L. gibba and L. minor, respectively. Throughout the course of eight days, these plants and reactor water were gathered every day. The acid mine water's pH, temperature, and electric conductivity were also tested every day. The L. gibba and L. minor were cleaned, dehydrated, and burned in a drying oven for a whole day at 300 oC. ICP-MS (Inductively Coupled Plasma Mass Spectroscopy) was used to determine the Mo+, Pb+, and Cu++ content of the plant and water samples. The concentrations of Mo, Pb, and Cu in the acid mine fluids of the copper mining were 30±4, 260±12, and 15535±322 μg L−1, respectively.in that order. When it came to extracting Mo, Pb, and Cu from the acidic fluids of the copper mining, L. gibba and L. minor performed well and efficiently compared to control samples; they did so 29 and 177 times for Mo, 30 and 109 times for Pb, and 495 and 1150 times for Cu. Considering all these findings, it has been shown that L. gibba and L. minor have the ability to efficiently remove Mo, Pb and Cu in acid mine fluids and can be good rehabilitation plants for polluted waters.

With widespread resistance to a limited number of insecticides available for medical and veterinary pests, new insecticides and insecticide synergists are desperately needed in this market space. We assessed the topical toxicity of carvone, menthone, and fenchone compared to permethrin and methomyl against the yellow fever mosquito, Aedes aegypti, and the house fly, Musca domestica. We also evaluated the synergistic potential of the monoterpenoids with permethrin and methomyl. Additionally, we assessed the acetylcholinesterase inhibitory potential of each monoterpenoid compared to methomyl. While all three monoterpenoids performed relatively poorly as topical insecticides (LD50 > 4000 ng/mg on M. domestica; > 6000 ng/mg on Ae. aegypti), they synergized both permethrin and methomyl as well as or better than piperonyl butoxide (PBO). Carvone and menthone yielded synergistic co-toxicity factors (23 and 29, respectively), which were each higher than PBO at 24 h. Acetylcholinesterase inhibition did not appear to explain the toxic or synergistic effects of the three monoterpenoids with IC50 values greater than 1 mM for all, compared to the 2.5 and 1.7 µM for methomyl on Aedes aegypti and Musca domestica, respectively. This study provides valuable monoterpenoid toxicity and synergism data on two pestiferous insects and highlights potential for these chemistries in future pest control formulations.