Dam breaches have catastrophic consequences, causing severe property damage, life loss, and environmental impact. The Kulekhani reservoir rockfill dam break was studied to evaluate the downstream impact. The appropriate breaching parameter of MacDonald and Langridge (1984) regression equations was selected based on the sixteen observed dam failure cases and cross-sectional geometry of the existing dam of Kulekhani. The 2D Diffusion Wave and Full Dynamic Wave Equation were applied for downstream flood assessment, Full Dynamic Wave was able to capture the physical flow phenomena like river bend effects resulting in higher flow velocity at the outer bend, and formation of eddies considering losses. The application of a Full Dynamic Equation was found to be appropriate for rapidly varying unsteady flow considering steep slopes, and sudden changes in channel geometry. Flood mapping of water depth, flow velocity, flood intensity, and arrival time were carried out for flood hazard assessment classified by the American Society of Civil Engineers (ASCE). Flow depth and extension of the flow area were compared to identify the affected area, higher flow depth and larger extension were observed using a Full Dynamic Wave Equation as a result of less flow velocity considering the losses. Almost 17 minutes of the arrival time of peak difference at the Bagmati River confluence was evaluated between the models which plays an important role in decision-making for selection of the flood model. Flood mitigation with river diversion works through a hydraulic measure of Levee was suggested to protect the highly affected households of Ranche, Nagmar, Khanikhet, and Debaltar towns. Most of the household was found to be safe after the construction of the Levee except for eleven houses that lie along the river below flood elevation of 1269.6 m.a.s.l. This signifies the importance of room for the rivers and the human settlement near the river might be life-threatening.

Flooding, exacerbated by climate change, poses a significant threat to certain areas, increasing in frequency and severity. In response, the construction of supplementary dams has emerged as a reliable solution for flood management. This study employs a Remote Sensing (RS) approach integrated with GIS to assess the feasibility of constructing a supplementary dam near Linville, Brisbane, Australia, with the aim of mit-igating floods and preventing overtopping failure at the Wivenhoe Dam. Using QGIS software and a 25-meter resolution DEM from the Queensland Spatial Catalogue ‘QSpatial’ website, four potential dam sites were analysed, considering cross-sections, watershed characteristics, and water volume calculations. Systematic selection criteria were applied to identify the most optimal option based on dam wall di-mensions, volume-to-area, and volume-to-cost ratios. The selected option was further assessed against predefined criteria, yielding one optimal choice. The study provides insights into the feasibility and ef-fectiveness of supplementary dam construction for flood mitigation in the region, with recommendations for future research and implementation.

Beef has one of the highest climate footprints of all foods, and therefore the hamburger has been targeted for substitution by numerous plant-based alternatives. However, many consumers find the taste of these alternatives lacking, and thus we proposed a hybrid meat and plant-based burger as a lower threshold alternative for these consumers. The burger was made from 50% meat (beef and pork, 4:1) and 50% plant-based ingredients, including texturised legume protein and had a climate footprint less than half that of a beef burger. Texture and sensory properties were evaluated instrumentally and through a consumer survey (n = 381) using the check-all-that-apply (CATA) method. Moisture properties indicated a significantly juicier eating experience for the hybrid compared to a beef burger, which was supported by the CATA survey. From texture profile analysis the hybrid burger was significantly softer and less cohesive than a beef burger. Despite having different CATA term profiles overall liking of the hybrid and a beef burger were not significantly different. Penalty analysis indicated that “meat flavour”, “juiciness”, “spiciness”, and “saltiness” are the most important attributes for a burger. In conclusion, consumers may be open to reducing their meat consumption by way of hybrid meat and plant-based products.

Beginning with navigation system design, this paper presents a comprehensive strategy for enhancing the search and rescue capabilities of agile mobile robots. Towards this, the autonomous ground vehicle (AGV) utilizes surface classification to determine and prioritize the terrain it is traversing. Our developed system design incorporates real-time terrain data with task objectives at a high level, ensuring that the robot can effectively navigate complex and ever-changing environments. This design, in conjunction with the introduction of a novel lightweight surface classification model, forms the basis of our adaptive terrain perception and decision-making systems, enabling robots such as Jackal to adapt rapidly and make the decisions necessary to complete the task. Subsequently, we exhaustively validated these systems through a series of extensive experiments in a variety of terrains, including normal and mixed terrains, demonstrating their robustness and efficacy in real-life situations.

Retrogressive breach failures or coastal flow slides occur naturally in the shoreface in fine sands near dynamic tidal channels or rivers. They sometimes retrogress into beaches, shoal margins and river banks where they can threaten infrastructure and cause severe coastal erosion and flood risk. Ever since the first reports were published in the Netherlands over a century ago, attempts have been made to understand the geo-mechanical mechanism of flow slides. In this paper we have established that events, observed during the active phase, are characterized by a slow and steady retrogression into the shoreline, often continuing for many hours. This can be explained by the breaching mechanism, as elaborated in this paper. Recently, further evidence has become available in the form of video footage of active events in Australia and elsewhere, often publicly posted on the internet. All these observations justify the new term ‘retrogressive breach failure’ (RBF event). The mechanism has been confirmed in small-scale flume tests and in a large-scale field experiment. With a better understanding of the geo-mechanical mechanism, current protection methods can be better understood and new defense strategies can be envisaged. In writing this paper, we hope that the coastal science and engineering communities will better recognize and understand these intriguing natural events.

Given the opportunities offered by foreign investment in energy infrastructure mostly by Chinese firms, the Government of Cambodia is giving high priority to developing hydropower resources for reducing energy poverty and powering economic growth. Using a “Political ecology of the Asian drivers” framework, this paper assesses China’s involvement in the development of large dams’ in Cambodia and its impacts on the access of natural resources such as water and energy by dam builders, local communities and the government. This analysis is based on 61 interviews and 10 focus group discussions with affected communities, institutional actors, Chinese dam builders and financiers in relation to the first large Chinese dam built in Cambodia, the Kamchay dam. Based on the results of the analysis this paper makes recommendations on how to improve the planning, implementation and governance of large dams to ensure that the dams’ benefits are shared more equally.

The catastrophic failure of two dams in Libya in the night of 10th and 11th September 2023, resulted in a significant amount of water and debris destroying a large part of the city of Derna, which is located downstream of the two dams. The flood caused more than 6000 fatalities and the dis-placement of thousands of people from the city. The dams failed due to heavy rainfall caused by the Medicane Daniel, resulting in intense precipitation and the dams overspilling after reaching full capacity. This paper analyses the consequences of the dam breach by modelling the flow discharge and the flooding of the city of Derna. The analysis compares the computed quantities with the findings of the post-event satellite image analysis from UNOSAT and Copernicus, the field reports, and information gathered from the social media through AI detection. The results allows to better understand the dynamics of the dam breach, its initial parameters and an assessment of the accu-racy of the results.

Determination of the parameters of the movement of surrounding objects, and in particular their speed, is one of the basic skills of a human being. The study of development of basic concepts of motion has been done for years with different methods and in different contexts. We have analyzed the effect of the physical/scientific image of the world introduced to children by school education and its long- and short-term cognitive consequences. Our studies showed that children differentiate the concept of speed into two more specific concepts: average speed and instantaneous velocity. In the present work we present how the gender context is superimposed on this general picture. We found that initial, genuine pre-school concept of speed of girls and boys is, on average, different. Our analysis shows also that this gender effect vanishes quickly together with the appearance of physical definitions of kinematical quantities in physics/science curricula. We discuss also methodological aspect of the statistical ‘gender gap’ measure and we calculated the gender effect chance probability, p-value, to be slightly less than 0.001. The importance of observed effect for the sustainable science teaching processes is discussed.

GNSS receivers are nowadays commonly used in monitoring applications, e.g., in estimating crustal and infrastructure deformations. This is basically due to the recent improvements in GNSS instruments and methodologies that allow high precision positioning, 24 h availability and semiautomatic data processing. In this paper, GNSS estimated deformations on a dam structure have been analyzed and compared with pendulum data. This study has been carried out for the Eleonora D’Arborea (Cantoniera) dam, which is in the Sardinia Island. Time series of pendulum and GNSS over a time span of 2.5 years have been aligned so to be comparable. Analytical models fitting these time series have been estimated and compared. Those models were able to properly fit pendulum data and GNSS data, with standard deviation of residuals smaller than one millimeter. This encouraging results led to the conclusion that GNSS technique can be profitably applied to dam monitoring allowing a denser description, both in space and time, of the dam displacements than the one based on pendulum observations.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

The physical properties of a structure such stiffness although can be determined by some statical tests, the identification of damping parameter requires a dynamic test. In general, both theoretical prediction and experimental identification of damping are quite difficult. There are many different techniques available for damping identification, and each method gives a different damping parameter. The dynamic indentation method, rheometry, atomic force microscopy, and resonant vibration tests are commonly used to identify the damping of materials, including soft materials. While the viscous damping ratio, loss factor, complex modulus and viscosity are quite common to describe damping of materials, there are also other parameters such as the specific damping capacity, loss angle, half-power bandwidth, and logarithmic decrement to describe damping of various materials. Often one of these parameters is measured in practical applications and the measured damping parameter needs to be converted into another damping parameter for comparison purposes. In this review, the theoretical derivations of different parameters for the description and quantification of damping and their relationships, and the methods for damping identification are presented. The expressions for both high damping and low damping are included and evaluated. This paper could be a primary resource for damping research and teaching.

Deterministic simulations using the SWAN model were conducted along a stretch of the Tietê-Paraná waterway in the Ilha Solteira dam reservoir, São Paulo, Brazil, to assess the water waves generated by winds. Simultaneously employs a probabilistic metamodeling approach (PCE) and Sobol indices, to quantify uncertainty of the five involved physical parameters (wind velocity and direction, bottom friction (JONSWAP), whitecapping and depth-induced breaking index). In the deterministic part, Janssen’s formulation yielded the most successful and accurate estimations of wave heights. Probabilistic analysis underscored the importance of wind data and the whitecapping parameter in model calibration, with a significant influence of wind speed indicated by Sobol indices. The results not only refined the model calibration process, but also allowed the creation of contour maps for wave height and period that offer practical pre-project applications. This work advances understanding of wind wave hydrodynamics deterministically and probabilistically, with good concordance and performance indices compared to field data, despite being scarce.

Jasmonates (JAs), including jasmonic acid (JA) and its biologically active derivative JA-Ile, are lipid-derived plant signalling molecules. They govern plant responses to stresses, such as wounding and insect herbivory. Wounding elicits a rapid increase of JA and JA-Ile levels as well as the expression of JAR1, coding for the enzyme involved in JA-Ile biosynthesis. Endogenous increase and application of JAs, such as MeJA, a JA methylester, result in increased defence levels, often accompanied by diminished growth. The function of jarin-1 in Arabidopsis thaliana was assessed. To investigate whether jarin-1 does function similarly in other plants, we tested this in Medicago truncatula, Solanum lycopersicum, and Brassica nigra seedlings in a root growth inhibition assay. Application of jarin-1 alleviated the inhibition of root growth after MeJA application in M. truncatula seedlings, proving that jarin-1 is biologically active in M. truncatula. Jarin-1 did not show, however, a similar effect in S. lycopersicum and B. nigra seedlings treated with MeJA. Even JA-Ile levels were not affected by application of jarin-1 in wounded leaf disks from S. lycopersicum. Based on these results, we conclude that the effect of jarin-1 is highly species-specific. Researchers intending to use jarin-1 for studying the function of JAR1 or JA-Ile in their model plants, must test its functionality before use.

Estimation of the potential consequences from events occurring downstream of a dam are part of the risk assessment needed during the installation phase of a new dam. In case of specific Natural or Man Made ongoing or prospected events, it may be also important to carry out fast computations that can provide information on the areas at risk either because the original design analyses are not available or because the parameters needed are different. This study is aimed to develop a procedure that strongly facilitates the preparation of the input deck and the derivation of the output quantities to allow a fast analysis of a dam break event using a shallow water model, NAMI DANCE, as the analysis tool.

Dams significantly impact the environment, industry, residential areas, and agriculture. Efficient dam management can mitigate negative impacts and enhance benefits such as flood and drought reduction, energy efficiency, water access, and improved irrigation. This study tackles the critical issue of predicting dam occupancy levels precisely within the framework of Integrated Water Resource Management (IWRM). Our research proposes that combining the physical model of evapotranspiration using the Penman–Monteith equation with data-driven models based on historical reservoir data, weather data, and consumption data is essential for accurately predicting occupancy levels. We implemented various prediction models, including Random Forest, Extra Trees, Long Short-Term Memory, Orthogonal Matching Pursuit CV, and Lasso Lars CV. To strengthen our proposed model with robust evidence, we conducted a statistical test on the MAPE values. We achieved a remarkable accuracy in predicting the occupancy level one month ahead, with an error margin of just 1% using Extra Trees. This study represents a pioneering effort in providing guidance and proposing a hybrid model in this field.

Fibre-based dietary interventions are at the forefront of gut microbiome modulation research, with a wealth of 16S rRNA information to demonstrate the prebiotic effects of isolated fibres. However, there is a distinct lack of data relating to the effect of a combination of soluble and insoluble fibres in a convenient to consume fruit juice food matrix on gut microbiota structure, diversity, and function. Here, we aimed to determine the impact of the MOJU Prebiotic Shot, a fruit juice drink blend containing chicory inulin, baobab, golden kiwi, and green banana powders, on gut microbiota structure and function. Healthy adults (n = 20) were included in a randomized, double-blind, placebo-controlled, cross-over study receiving 60ml MOJU Prebiotic Shot or pla-cebo (without the fibre mix) for 3 weeks with a 3-week wash-out between interventions. Shotgun metagenomics revealed significant between-group differences in alpha and beta diversity. In addition, the relative abundance of the phyla Actinobacteria and Desulfobacteria was significantly increased as a result of the prebiotic intervention. 9 species were observed to be differentially abundant (uncorrected p-value of <0.05) as a result of the prebiotic treatment. Of these, Bifidobacterium adolescentis and CAG-81 sp900066785 (Lachnospiraceae) were present at increased abundance relative to baseline. Additionally, KEGG analysis showed an increased abundance in pathways associated with arginine biosynthesis and phenylacetate degradation during the prebiotic treatment. Our results show the effects of the daily consumption of 60ml MOJU Prebiotic Shot for 3 weeks and provide insight to the functional potential of B. adolescentis

Maintaining an adequate micronutrient status can be achieved by following a complete, diverse diet. Yet, food trends in Western countries show suboptimal consumption of healthy nutrients. In this study we explored the prevalence of vitamin and mineral imbalances in a general population cohort of Dutch adults, and evaluated the effect of a digital lifestyle program on the nutritional status and nutrition health behaviors of these individuals. A micronutrient panel was measured in 348 participants, alongside a dietary assessment. One-hundred users subsequently underwent a remeasurement. We identified at least one nutritional imbalance in 301 individuals (86.5%). 80% improved and normalized B6, 67% improved folate, 70% improved B12, and 86% improved vitamin D. Iron abnormalities were corrected in 75% of participants. In conclusion, this study found micronutrient deficiencies of easily obtainable vitamins through diet or supplementation such as B vitamins and vitamin D were more prevalent than expected in a Dutch population. This can partly be explained by an insufficient consumption of food groups rich in B vita-mins. Our preliminary results in those remeasured after a digitally-enabled lifestyle intervention show these imbalances can be corrected with adequate behavioral support in a “food as medicine” approach complemented with supplementation where needed.

Background/Objectives: Phenylketonuria is a hereditary metabolic disorder characterized by a deficiency of phenylalanine hydroxylase. Main treatment for PKU is a phenylalanine-restricted diet. Exclusion of protein rich natural foods and inclusion of low-Phe substitutes may give rise to an imbalanced diet increasing the risk of overweight and obesity in PKU is a cause of concern. We aimed to evaluate the body composition and nutritional biochemical biomarkers in adult PKU patients who are on Phe-restricted and essential amino acids supplemented nutrition therapy and to investigate the relationships, between these parameters and patient gender, adherence to dietary therapy and disease type defined as mild or classic PKU. Methods: The study group comprised 37 PKU patients and 26 healthy siblings as controls. The participants were assessed based on an analysis of anthropometric parameters, body composition and biochemical test results. Results: PKU patients do not have a higher incidence of overweight and obesity than healthy controls, and the proportion of energy derived from carbohydrates in their diets was below the recommended level, and the total energy intake was below the recommended daily allowance. It was remarkable that patients with a treatment adherence ratio of &lt;50% displayed a higher prevalence of overweight and abdominal obesity in comparison to those with a more favorable treatment adherence ratio. Conclusions: In view of the growing prevalence of overweight in the general population, PKU patients should be kept under close long-term follow-up. Particularly in the group with low treatment compliance, more caution should be paid in terms of adverse outcomes.

Dynamic systems which underly controlled systems are expected to increase in complexity as robots, devices, and connected networks become more intelligent. While classical stable systems converge to a stable point (a sink), another type of stability is to consider a stable path rather than a single point. Such stable paths can be made of saddles which draw in trajectories from certain regions, and then push the trajectory toward the next saddle point. These are chains of saddles are called stable heteroclinic channels (SHCs), and can be used in robotic control to represent time sequences. While we have previously shown that each saddle is visualizable as a trajectory waypoint in phase space, how to increase the fidelity of the trajectory was unclear. In this paper, we hypothesized that the waypoints can be individually modified to locally vary fidelity. Specifically, we expected that increasing the saddle value (ratio of saddle eigenvalues) causes the trajectory to slow to more closely approach a particular saddle. Combined with other parameters that control speed and magnitude, a system expressed with an SHC can be modified locally, point by point, without disrupting the rest of the path, supporting their use in motion primitives. However, even more complex trajectory shape modifications are possible. While some combinations can enable a trajectory to better reach into corners, other combinations can rotate, distort and round the trajectory in the region of a corner. In our example, modifying select saddle values produced a 32% decrease in the trajectory error of a complex trajectory produced using this system. This is an effect not visible in previous 1D studies, that can lead to different learnable and tunable representations of dynamic systems.

This study investigates cloud cavitation suppression around a model scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift-drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor-liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift-drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems.

Worldwide, it is estimated that at least 1 in 4 adults suffers from hypertension, and this number is expected to increase as populations grow and age. Blood pressure (BP) possesses substantial heritability, but is also heavily modulated by lifestyle factors. As such, digital, lifestyle-based in-terventions are a promising alternative to standard care for hypertension prevention and man-agement. In this study we assessed the prevalence of elevated and high BP in a Dutch general pop-ulation cohort undergoing a health screening, and observed the effects of a subsequent self-initiated, digitally-enabled lifestyle program on BP regulation. Baseline data were available for 348 participants, of which 56 had partaken in a BP-focused lifestyle program and got re-measured 10 months after the intervention. Participants with elevated SBP and DBP at baseline showed a mean decrease of 7.2 mmHg and 5.4 mmHg, respectively. Additionally, 70% and 72.5% of participants showed an improvement in systolic and diastolic BP at remeasurement. These improvements in BP are superior to those seen in other recent studies. The long-term sustainability and the efficacy of this and similar digital lifestyle interventions will need to be estab-lished in additional, larger studies.

Background: Poor patient flow can lead to adverse outcomes for patients and organisational inefficiency. Many hospitals have addressed suboptimal patient flow by increasing resourcing, such as bed stock and staffing, however, this is an unsustainable approach. In determining the nature of poor patient flow issues, it is important to collect data from healthcare professionals who manage patient flow on a daily basis. Doing so provides insights into the current state of patient flow management in its entirety, whilst also helping with the development of sustainable solutions.; Methods: Thirteen semi-structured interviews were conducted with clinicians who were directly involved with patient flow at a tertiary care centre in Tasmania, Australia. Results: Through a thematic analysis method, four major themes were developed: managing patient flow, communication for decisions, tools as enablers and barriers and increasing complexity. Conclusions: The findings of this study provide great insights into patient flow issues, with potential solutions identified to address them.

The risk related to embankment dam breaches needs to be evaluated in order to prepare emergency action plans. The physical and hydrodynamic parameters of the flood wave generated from dam-failure event correspond to various breach parameters such as width, slope and formation time. This study aimed to simulate dam-breach failure scenario of Yabous dam (NE Algeria) and analyze its influence on areas (urban and natural environments) downstream the dam. The simulation was completed using the sensitivity analysis method in order to assess the impact of breach parameters on the dam-break scenario. The propagation of flood wave associated to dam-break was simulated using the one-dimensional HEC-RAS hydraulic model. This study ap-plied a sensitivity analysis of three breach parameters (slope, width, and formation time) in five sites selected downstream the embankment dam. The simulation showed that the maximum flow of the flood wave recorded at the level of the breach was 8768 m3/s, which gradually attenuated along the river course to reach 1579.2m3/s at about 8.5km downstream the dam. This study estab-lished the map of flood-prone areas that illustrated zones threatened with the flooding wave trig-gered by the dam failure due to extreme rainfall events. The sensitivity analysis showed that flood wave flow, height and width revealed positive and similar changes for the increase in adjustments (±25% and ±50%) of breach width and slope in the 5 sites. However, flood wave parameters of breach formation time showed significant trends that changed in the opposite direction compared to breach slope and width.

Dams are a critical infrastructure system for many communities, but they are also one of the most challenging to inspect. Dams are typically very large and complex structures, and the result is that inspections are often time-intensive and require expensive, specialized equipment and training to provide inspectors with comprehensive access to the structure. The scale and nature of dam inspections also introduces additional safety risks to the inspectors. Unmanned aerial vehicles (UAV) have the potential to address many of these challenges, particularly when used as a data acquisition platform for photogrammetric three-dimensional (3D) reconstruction and analysis, though the nature of both UAV and modern photogrammetric methods necessitates careful planning and coordination for integration. This paper presents a case study on one such integration at the Brighton Dam, a large-scale concrete gravity dam in Maryland, USA. A combination of multiple UAV platforms and multi-scale photogrammetry was used to create two comprehensive and high-resolution 3D point clouds of the dam and surrounding environment at intervals. These models were then assessed for their overall quality, as well as their ability to resolve flaws and defects that were artificially applied to the structure between inspection intervals. The results indicate that the integrated process is capable of generating models that accurately render a variety of defect types with sub-millimeter accuracy. Recommendations for mission planning and imaging specifications are provided as well.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

To address the issue of intelligent optimization algorithms being prone to local optima, resulting in insufficient feature extraction and low fault type recognition rates when optimizing Variational Mode Decomposition (VMD) and Support Vector Machine (SVM) parameters, this paper proposes a fault diagnosis method based on an improved Artificial Gorilla Troops Optimization (GTO) algorithm. The GTO algorithm is enhanced using Logistic chaotic mapping, a linear decreasing weight factor, the global exploration strategy of the Osprey Optimization Algorithm, and the Levy flight strategy, improving its ability to escape local optima, adaptability, and convergence accuracy. This algorithm is used to optimize the parameters of VMD and SVM for fault diagnosis. Experiments on fault diagnosis with two datasets of different sample sizes show that the proposed method achieves a diagnostic accuracy of no less than 98% for samples of varying sizes, with stable and reliable results.

Selection is a fundamental part of the plant breeding process, enabling the identification and development of varieties with desirable traits. Thanks to advances in genetics and biotechnology, the selection process has become more precise and efficient, resulting in faster breeding progress and better adaptation of crops to environmental challenges. Genetic parameters related to gene additivity and epistasis play a key role and can influence decisions on the suitability of breeding material. In this study, 188 rapeseed doubled haploid lines were assessed in field conditions for resistance to Leptosphaeria spp. Through next-generation sequencing, a total of 133,764 molecular markers (96,121 SilicoDArT and 37,643 SNP) were obtained. The similarity of the DH lines at the phenotypic and genetic levels was calculated. The results indicate that the similarity at the phenotypic level was markedly different than the similarity at the genetic level. Genetic parameters related to additive gene action effects and epistasis (double and triple) were calculated using two methods: based on phenotypic observations only and using molecular marker observations. All evaluated genetic parameters (additive, additive-additive and additive-additive-additive) were statistically significant for both estimation methods. The parameters associated with the interaction (double and triple) had opposite signs depending on the estimation method.

Introduction: Carcinoid heart disease is a rare cause of right-sided valvular dysfunction, an important complication in patients with carcinoid syndrome. Objectives: We aim to present our own experience regarding early myocardial dysfunction in patients with carcinoid syndrome. Methods: 64 patients (35-90 year old, 62,5% female, 37,5% male patients) with carcinoid syndrome were evaluated be-tween October 2017 and June 2021. All patients underwent two-dimensional echocardiography with additional tissue Doppler and speckle-tracking techniques. For all patients there were measured urinary level of 5- hydroxyindolacetic acid, serotonin and NT-proBNP values. Results: The following echocardiographic features: global longitudinal strain of both ventricles, mean systolic velocity of the left ventricle, systolic velocity of the free wall of right ventricle, correlated with high values of specific biomarkers: serotonin, and urinary 5-hydroxyindolacetic acid, and also with the presence of hepatic metastases and poorly differentiated tumors. Discussion: In this study we identified several patients with early myocardial dysfunction due to carcinoid syndrome, representing a predictive model of poor prognosis, requiring further investigations. Conclusion: Echocardiographic assessment based on the measurement of systolic velocities, as well as the global longitudinal strain of both ventricles, together with specific biomarkers may contribute to better recognition of carcinoid heart disease in clinical practice, but this needs validation through further studies enrolling larger number of patients.

The objective of this study is to determine the relationship between body condition score (BCS) and body carcass fat (BCF) of ewes at two key stages of the production cycle. Data were collected from 88 Coopworth ewes including BCS measurements manually evaluated by the farm manager, BCF measurements determined by computerized tomography (CT) and body parameter measurements automatically determined by an image processing application. Artificial neural network (ANN) statistical analysis method was used to develop a relationship between the body parameters and the BCF with an r2=0.96 and RMSE=1.01 using all top and side variables.

With the significant annual increase in the market demand for biopesticides, the industrial production demand for predatory mites, which hold the largest market share among biopesticides, has also been rising.To achieve efficient and low energy consumption control of predatory mite breeding environmental parameters, accurate estimation of breeding environmental parameters is necessary. This paper collects and pre-processing hourly time-series data of temperature and humidity from industrial breeding environments. Time series prediction models such as SVR, LSTM, GRU, and LSTNet are applied to model and predict historical data of the breeding environment. Experiments validate that the LSTNet model is more suitable for such environmental modeling. To further improve prediction accuracy, the training data for the LSTNet model is enhanced using hierarchical clustering of time-series features. After augmentation, the root mean square error (RMSE) of temperature prediction decreased by 27.3%, and the RMSE of humidity prediction decreased by 32.8%, significantly improving the accuracy of multi-step predictions and providing substantial industrial application value.

Extraction techniques of important bioactive molecules from the major concern of Seafood byproducts are getting emphasis for better valorization. Employing green extraction technologies for efficient and quality production of these bioactive molecules is also strictly required. Hence, understanding the extraction process parameters to effectively design an applicable optimization strategy could make this real. In this review, statistical optimization strategies applied for the extraction process parameters of bioactive molecules from Seafood byproducts are focused. The type of experimental designs, and techniques applied to criticize and validate the effects of independent variables on the extraction output was addressed. Dominant parameters studied were enzyme/substrate ratio, pH, time, temperature and power of extraction instruments. The yield of bioactive compounds, chitin and chitosan, proteins and peptides, enzymes and carotenoids (Astaxanthins) were the most studied responses. Efficiency and/or economic and quality considerations and their selected optimization strategies that favour the production of potential bioactive molecules were also reviewed.

We are in amidst of COVID-19 pandemic. Since Dec 2019, severe acute respiratory corona virus (SAR-CoV-2) has infected more than half a billion people killing nearly 7 million people worldwide. Now the BA.5 variant of SARS-CoV-2 is causing mayhem and driving the global surge. Epidemiologist are aware of the fact that this virus is capable of escaping immunity and likely to infect the same person multiple times despite adequate vaccination status. Elderly people of age more than 60 years and those with underlying health conditions are considered as high-risk who are likely to suffer complications and death. While it is tempting to frame complications and mortality from COVID-19 as a simple matter of too much of a virulent virus in too weak of a host, much more is at play here. Framing the pathophysiology of COVID-19 in the context of the Chrousos and Gold model of the central stress response system can shed insight into its complex pathogenesis. Understanding the mechanisms by which pharmacologic modulation of the central stress response system via administration of clonidine and/or dexamethasone may offer an explanation as to why a viral pathogen can be well tolerated and cleared by one host while inflaming and killing another.

Many farms are replacing the lighting with light emitting diode (LED) bulbs because of the technological modernization. We aimed to investigate the effects of incandescent light (IL) and LED lighting on Cobb500 broiler chickens for six weeks. Production parameters (body weight, feed consumption, feed conversion ratio), calculated slaughter values (yield%, relative breast%, thigh%) and breast meat quality parameters (pH at 45 min and 24 h postmortem, color, drip loss, kitchen equipment losses, shear force, meat composition) were recorded. Non-stop recordings were used to analyze the behavior of the birds in several periods of the rearing. LED group was significantly better in body weigh parameter between week 1-5 and feed conversion ratio between week 2-3. The most significant difference in behavior was observed in the middle of the rearing period. The chickens in the LED group spent more eating time, drinking time, interacting, and resting less. There was no difference in the meat quality parameters, only shear force was significantly lower in the LED group (1781.95±0.33 g/s vs. 2098.82±0.42 g/s). Based on our results, LED lighting can bring positive changes in animal production efficiency, behavior, and important characteristics for meat consumers.

Abstract: Green walls and green dams are increasingly being considered as part of many nation-al and international desertification initiatives. This paper studies the spatiotemporal evolution of the green dam in the Moudjbara region (Djelfa Province, Algeria) from 1972 to 2019 by using Landsat imagery, Land Change Modeler and Open Land package. The future evolution of pine plantations for the year 2029 was also forecasted, based on an anthropogenic scenario (i.e., an-thropogenic pressure is the main driver of the green dam destruction). Our findings revealed that the green dam project was successful for a few years, but after that, pine plantations deteri-orated significantly due to forest harvesting, livestock overgrazing, and the proliferation of the pine caterpillar processionary, which destroyed most of the reforestation. Land Change Modeler predicted a huge degradation of pine plantations for the year 2029, and if the deforestation con-tinues at the same rate, the green dam will disappear in the Moudjbara region during the next few decades. Aware of this threat, the Algerian authorities are now planning to reforest more than 1.2 million ha under the latest rural renewal policy by introducing new principles related to sustainable development, fighting desertification, and climate change adaptation

In large infrastructures such as dams, which have a relatively high economic value, ensuring the proper operation of the associated hydraulic facilities in different operating conditions is of utmost importance. To ensure the correct and successful operation of the dam's hydraulic equipment and prevent possible damages, including gates and downstream tunnel, to build laboratory models and perform some tests are essential (the advancement of the smart sensors based on artificial intelligence is essential). One of the causes of damage to dam bottom outlets is cavitation in downstream and between the gates, which can impact on dam facilities, and air aeration can be a solution to improve it. In the present study, six dams in different provinces in Iran has been chosen to evaluate the air entrainment in the downstream tunnel experimentally. Three artificial neural networks (ANN) based machine learning (ML) algorithms are used to model and predict the air aeration in the bottom outlet. The proposed models are trained with genetic algorithms (GA), particle swarm optimization (PSO), i.e., ANN-GA, ANN-PSO, and ANFIS-PSO. Two hydrodynamic variables, namely volume rate and opening percentage of the gate, are used as inputs into all bottom outlet models. The results showed that the most optimal model is ANFIS-PSO to predict the dependent value compared with ANN-GA and ANN-PSO. The importance of the volume rate and opening percentage of the dams' gate parameters is more effective for suitable air aeration.

The acoustic environment in learning spaces significantly influences learning effectiveness and occupant well-being. Recent studies have shown that a series of architectural factors within physical learning environments can impact students' educational experiences. This research delves into the relationship between architectural characteristics and the perceived acoustic environment among 467 primary students in 19 learning spaces across 9 schools in Chile. The survey comprises a student questionnaire, a checklist evaluating space characteristics, and acoustic measurements of indoor noise levels during occupied conditions. Examined topics include Indoor Environmental Quality (IEQ) comfort perception, noise annoyance, hearing ability, and acoustic preference. Architectural characteristics considered encompass flexible and acoustic space design parameters. The results indicated that noise discomfort was a common issue, especially in traditional learning spaces without acoustic treatment. The type of learning space (traditional or flexible settings) has a greater impact on acoustic perception particularly concerning noise discomfort and acoustic preference. However, poorly acoustic spaces lacking absorbing materials or exhibiting lower spatial density (m2 per student) contribute to increased indoor noise levels affecting noise annoyance caused by children's talking inside. The study emphasizes the importance of considering both architectural design and acoustic conditioning for optimizing the acoustic experience in educational spaces.

The aim was to identify if surface electromyography (sEMG) parameters are indicative of post-activation potentiation (PAP)/post-activation performance enhancement (PAPE), in terms of twitch potentiation and voluntary performance. Three databases were used in March 2024, with the following inclusion criteria: (a) original research, assessed in healthy human adults, (b) sEMG parameters were measured. The exclusion criteria were: (a) studies with no PAP/PAPE-protocol, (b) non-randomized control trials. The following data were extracted: study characteristics/demographics, PAP/PAPE-protocols, sEMG parameters, twitch/performance outcomes, and study findings. A modified physiotherapy evidence database (PEDro) scale was used for quality assessment. Fifteen randomized controlled trials (RCTs), with a total of 199 subjects were included. The M-wave amplitude (combined with a twitch torque outcome) was shown to generally be indicative of PAP. The sEMG amplitude (in some muscles) were found to be indicative of PAPE during ballistic movements, while a small decrease in the MdF (in certain muscles) were shown to reflect PAPE. Changes in the Hmax/Mmax ratio were found to contribute (temporally) to PAP, while the H-reflex amplitude was shown to be neither indicative of PAP nor PAPE. This review provides preliminarily findings suggesting that certain sEMG parameters could be indicative of PAP/PAPE. However, future research is warranted.

Aim: To evaluate the panmacular subthreshold micropulse laser treatment results among patients with central serous chorioretinopathy (CSC) and their correlation with functional and morphological parameters. Material and methods: The examined group included 10 non-treated and 41 treated patients with acute, recurrent, and chronic CSC (13 F, 38 M, mean age 44.11±6.5) and 14 healthy controls (6 F, 8 M, mean age 45±9.3). The BCVA examination, ophthalmoscopy, microp-erimetry, angio-OCT and OCT were performed. The medical history regarding chronic general disorders and known risk factors were recorded. Results: Complete resorption of SRF was obtained in 100% aCSC, 86.66% cCSC, and 63.63% r CSC. BCVA and RetSens significantly improved most of the patients treated in aCSC. The lowest BCVA and RetSens, but the largest pachyvessel and disease duration, were found in rCSC. A strong negative correlation between final BCVA and disease duration was found. No patient demonstrated laser lesions following treatment. Conclusions: The panmacular MPLT therapy leads to long-term enhancement of functional and morphological parameters in all CSC patients. The acute CSC patients showed the most significant improvement. The procedure is safe and could be considered a preferred treatment option for all active CSC cases. Timely treatment is crucial for beneficial outcomes.

Malaria is a disease spread by female mosquitos of the Anopheles genus. It is acutely prevalent in Sub-Saharan Africa, where 90% of malaria deaths occur annually. One Sub-Saharan African country historically impacted by malaria is Ethiopia. In the past twenty years, malaria prevalence has decreased throughout Sub-Saharan Africa; yet, anthropogenic environmental changes are changing the landscape of malaria. Scholarly literature has cited a positive relationship between hydroelectric dams and malaria in Sub-Saharan Africa. Ethiopia is currently expanding their hydroelectric infrastructure. The Gilgel Gibe III Dam is located on the Omo River in Southwestern Ethiopia. It began generating electricity in 2015 and its reservoir has a capacity of 14,700 million m3 of water. This research utilized Geographic Information Systems and Remote Sensing to identify populations at an increased risk of malaria due to Gilgel Gibe III Dam. Two different techniques were employed: the proximity approach and the remote sensing approach. The proximity approach was based on distance from the reservoir. It identified all populations living within three kilometers of the reservoir as being at an increased risk. The remote sensing approach evaluated the slope, elevation, water content, and land surface temperature of the study area to create a mosquito breeding habitat risk map. Then, populations living within three kilometers of the two main High-Risk areas were identified. This study suggests that mosquito breeding habitat risk is not equally distributed throughout the Gilgel Gibe III Reservoir. This causes certain populations to be at a heightened risk of malaria.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Despite the diaphragm's direct connection with the heart through the phreno-pericardial ligament, little is still known about the role of this primary breathing muscle in the cardiovascular system. The purpose of the present study was to determine the relationship of diaphragm muscle thickness, thickening, and strength with selected cardiovascular parameters. Thirty participants who qualified for a three-week post-COVID physiotherapy program were examined. Diaphragm muscle thickness on the left and right sides was assessed using ultrasound. Blood pressure and heart rate were evaluated by an automatic oscillometric device, while the rest of the cardiovascular parameters were calculated using standardized formulas from the literature. We found a relationship between the left diaphragm dome thickening ratio and systolic blood pressure, pulse pressure, stroke volume, cardiac index, ejection fraction, and saturation level measured after the 6-minute walk test (6-MWT). Patients with better left diaphragm dome strength were characterized by a lower difference in systolic blood pressure, pulse pressure, stroke volume, cardiac output, cardiac power output, ejection fraction, cardiac index, and pressure-heart rate product between pre- and post-6-MWT measurements. There was no correlation between right diaphragm dome function and cardiovascular parameters. There was no association of left and right hemidiaphragm function with resting cardiovascular parameters. In conclusion, the strength of the left hemidiaphragm plays an important role in the regulation and modulation of cardiovascular parameters during physical exertion.

Dams have made great contributions to human society, facilitating flood control, power generation, shipping, agriculture and industry. However, the construction of dams greatly impacts downstream ecological environments and nearby marine areas. To summarize these impacts, this review used recent research to comprehensively analyze how dam construction has affected river hydrology, geomorphology, and ecosystem of downstream reaches globally. Effects of dams on ecosystems occur through reduced river flow, reduced sediment flux, altered water temperature, changed estuary delta, altered composition and distribution of nutrients, altered structure and distribution of phytoplankton populations, caused habitat fragmentation, and blocked migration routes in river sections and adjacent seas. Besides, exploring new reservoir management strategies (including targeted control of dam storage and flushing sediment operations), banning fishing activities, and removing unnecessary dams (obsolete or small dams) are becoming crucial tools for ecosystem restoration.

Water pollution is a common problem for dams situated within an urban or agricultural catchment. This can negatively affect the hydro ecosystem, drinking, recreational and other uses of water. In this study, the drinking water quality class of the Roodeplaat Dam, South Africa which faces pollution problems was modeled using machine learning algorisms in Python Jupyter Notebook 6.0.0. Eleven monthly water quality parameters recorded at five sampling stations from January 1981 to September 2017 were used for training and testing the model. Five machine learning classifiers: Gaussian Naïve Bayes (GNB), K-nearest neighbors (KNN), Decision Tree (DT), Support Vector Machines (SVM), and Linear Regression (LR) at a test size of 20%, 25%, 30%, and 40% were used to classify water into five classes (Excellent to Very bad). It was investigated that the dam water has only three classes good, medium, and bad. The prediction accuracies of machine learning algorithms from the highest to the lowest were 96.39%, 96.17%, 92.25%, 90.20, and 54.19% for KNN, DT, SVM, GNB, and LR, respectively. Therefore, KNN at a test size of 30% was recommended to classify the water quality of Roodeplat Dam accurately. Hence, machine learning algorithms can be used to identify the class of water quality before the water is treated and distributed for drinking use.

For embankment slope stability, soil cohesivity is one of the most important shear strength parameters. The effect of cohesiveness on the slope stability of a homogeneous embankment dam under rapid drawdown loading conditions was examined in this study. With the use of numerical modeling in GeoStudio, different situations were explored based on cohesiveness (0 kN/m², 5 kN/m², 10 kN/m^2, and 15 kN/m²) under a 1 m per day drawdown rate. The factor of safety value obtained from the long-term steady-state condition under 15 kN/m² cohesion was equivalent to a 116.8% increase from the one obtained under 0 kN/m² cohesion. The factor of safety values obtained after subjecting the embankment to different soil cohesion levels yielded a p-value of 1.91 x 10^-41, according to the Analysis of Variance. The calculated p-value (alpha value) is less than 0.05, suggesting that the differences between the examined cohesiveness values based on the list of the factor of safety values are statistically significant. The findings derived in this study show that it is significant to capture the effect of material characteristics during the design phase of an embankment dam.

Recently, torrential rain and drought have occurred in close temporal proximity and for similar durations due to changes in the spatiotemporal patterns of rainfall owing to climate change. In particular, when a drought occurs, it tends to be prolonged, making it necessary to improve the operation of multi-purpose dams that not only control flooding but also serve as water supplies. In this study, standard water volume lines and action plans by response stage were improved so that water could be stored in advance of a drought instead of reservoir operation criteria set based on data from the past. The minimum water demand by use (domestic water, industrial water, and agricultural water) was also calculated. The improved reservoir operation criteria were applied to multi-purpose dams in the Nakdong River Basin, and their effects were analyzed by calculating additionally secured water volumes. In the future, in case of lowered water volumes in multi-purpose dams owing to a drought, the application of these improved reservoir operation criteria is expected to contribute to water supply stability by delaying entry into the drought stage, and minimizing the damages caused by limited water supplies.

Expansion tube is ideal energy absorber which dissipates kinetic energy through plastic deformation and friction. There is an urgent need to understand the influence of key parameter, e.g. semi angle, tube material, and friction coefficient, on the mechanical response and energy absorption characteristics of expansion tube. In the present work, the material properties of the tubes were tested under quasi-static loading condition, and the numerical simulations were carried out by using commercial software ABAQUS. Based on the validated finite element simulation, all the semi angle, tube material, and friction have significant effects on the energy absorption capacity of expansion tube. The expansion tube with high tensile stress of parent material have high energy absorption capacity, while the specific energy absorption is linear with the tensile stress/density of tube material. This work would give a guidance to the structural design and parent materials selection for expansion tubes.

Cymbidium goeringii, locally known as the spring orchid in Korea, is one of the most important and popular horticultural species in the family Orchidaceae. C. goeringii cultivars were originated from plants with rare phenotypes in wild mountains where pine trees commonly grow. This study aimed to determine the cultivar-specific combined genotypes (CGs) of short sequence repeats (SSRs) by analyzing multiple samples per cultivar of C. goeringii. In this study, we collected more than 4,000 samples from 67 cultivars and determined the genotypes of 12 SSRs. Based on the most frequent combined genotypes (CG1s), the average observed allele number and combined matching probability were 11.8 per marker and 3.118×10-11, respectively. Frequencies of the CG1 in 50 cultivars (n ≥ 10) ranged from 40.9% to 100.0%, with an average of 70.1%. Assuming that individuals with the CG1 are genuine in the corresponding cultivars, approximately 30% of C. goeringii on the farms and markets may be not genuine. The dendrogram of the phylogenetic tree and principal coordinate analysis largely divided the cultivars into three groups according to their countries of origin; however, the genetic distances were not distant among the cultivars. In conclusion, this dataset of C. goeringii cultivar-specific SSR profiles could be used for ecogenetic studies and forensic authentication. This study suggests that genetic authentication should be introduced for the sale of expensive C. goeringii cultivars. We believe that this study will help establish a genetic method for the forensic authentication of C. goeringii cultivars.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

Silicon carbide particle-reinforced aluminum matrix (SiCp/Al) composites are significant lightweight metal matrix composites extensively utilized in precision instruments and aerospace sectors. Nevertheless, the inclusion of rigid SiC particles exacerbates tool wear in mechanical machining, resulting in a decline in the quality of surface finish. This work undertakes a comprehensive investigation into the problem of tool wear in SiCp/Al composite materials throughout the machining process. Initially, a comprehensive investigation was conducted to analyze the effects of cutting velocity vc, feed per tooth fz, milling depth ap, and milling width ae on tool wear during high-speed milling under SCCO2-MQL (Supercritical Carbon Dioxide Minimum Quantity Lubrication) ultrasonic vibration conditions. Furthermore, a prediction model for tool wear was developed by employing the orthogonal test method and multiple linear regression. The model's relevance and accuracy were confirmed using F-tests and t-tests. Ultimately, through the utilization of a genetic algorithm, the milling parameters were optimized, resulting in the identification of the most optimal combination of parameters. Empirical findings suggest that the careful selection of milling parameters can significantly mitigate tool wear, extend the lifespan of the tool, and enhance the quality of the surface. This work serves as a significant point of reference for the processing of SiCp/Al composite materials.

Variable flow emitters are a new type of emitter for underground drip irrigation that are used in locations where soil moisture is difficult to transport to the surface, which leads to crop emer-gence difficulties. The flow channel structure parameters of emitters affect the hydraulic per-formance of the emitter and its anticlogging ability. In this study, the variable flow emitter at the conventional low–flow water supply stage is taken as the research object. A combination of CFD numerical simulation of a two–phase flow of water and sand and clear water testing of test samples is applied to study the influence laws of 10 groups of variable flow emitter structural combinations on the effluent flow rate (q), flow index (x), particle passage rate and flow field inside the flow channel. The results show that the Realizable k–ε turbulence model can be used to simulate the flow field inside the variable flow emitter flow channel. The nRMSE between the measured and simulated values of q is 11.23%, and the relative error between the measured and simulated values of x is 4.66%, which gives a high simulation accuracy. The polar analysis shows that the tooth angle A has the smallest effect on the effluent flow rate q0.1 under 0.1 MPa, x, and particle passage rate of the variable flow emitter. The depth of the flow channel D, the spacing of the teeth B, and the height of the teeth E have a different order of precedence in the influence of the three indices, which are D > B > E > A, B > E > D > A, and E > B > D > A, respectively. The value of particle passage rate is positively correlated with the mean flow velocity (v) and the mean turbulent kinetic energy (k) in the flow channel, and particle passage rate tends to increase and then decrease with the increase of x. The retention time (t) of the particles in the flow channel is closely related to the magnitude of v and k. Three multivariate linear regression equations (R2 = 0.883 ~ 0.995) were constructed for q0.1, x, and particle passage rate versus the flow channel structural parameters. Using the scipy.optimize.minimize function in Python, we de-termined the three optimal combinations of flow channel structural parameters corresponding to better hydraulic performance: q0.1 is 1.5 or 2 L/h (objective function y = min x), better clogging resistance (y = max particle passage rate), and both (y = min (0.5 x - 0.5 particle passage rate)). The research results can provide a ref-erence for the optimal design of variable flow emitters.

(1) Background: Cardiac resynchronization therapy (CRT) is essential for patients with heart failure and ventricular conduction abnormalities. Cardiomyopathy often includes left bundle branch block (LBBB) marked by delayed activation of the LV lateral wall and a widened QRS complex. Following CRT, patients with heart failure and LBBB have better outcomes and quality of life improvements. Various electrocardiographic and clinical parameters are thought to predict this improvement. The Kansas City Cardiomyopathy Questionnaire (KCCQ) is a reliable tool for measuring the quality of life in these patients. (2) Methods: We performed an observational prospective study over 69 individuals diagnosed with cardiac failure and dilatative cardiomyopathy with low FE and major LBBB and analyzed the correlations between patient outcomes after the procedure and the demographic, clinical, and electrocardiographic parameters, which include systolic blood pressure, ECG morphology elements, QRS duration, QRS area and associated comorbidities. (3) Results: Following our analysis a correlation between QRS area, intraprocedural systolic blood pressure, QRS duration and CRT outcomes assessed by the KCCQ score was observed which reflected that CRT has a hemodynamic impact and also affects the severity of ventricular asynchrony.; (4) Conclusions: The significant correlations observed with the KCCQ score show how CRT therapy impacts patients' quality of life, symptom burden, and functional status.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

Harmful algal blooms are a serious problem for humanity, so the development of tools and methods for their timely detection is an urgent task. The use of optical methods often allows scientists to solve problems of remote and automated monitoring. Temperature spectra of fluorescence can be used as distinctive features of algae, and the fluorescence parameters obtained from them can be used for identification. The paper presents a description of the fluorescence parameters of Alexandrium catenella, and shows their stability during cumulative cultivation. In addition, the cytometric properties of the culture and its pigment composition were studied. In addition, the article compares all the studied properties of this microalga with the alga Prorocentrum cordatum. We demonstrated clear differences in their fluorescence parameters, which makes it possible to distinguish these microalgae by optical methods, for example, during their dominant blooms.

In the context of smart agriculture, accurately estimating plant leaf chemical parameters is crucial for optimizing crop management and improving agricultural yield. Hyperspectral imaging, with its ability to capture detailed spectral information across various wavelengths, has emerged as a powerful tool in this regard. However, the complex and high-dimensional nature of hyperspectral data poses significant challenges in extracting meaningful features for precise estimation. To address this challenge, this study proposes an end-to-end estimation network for multiple chemical parameters of Astragalus leaves based on attention mechanism (AM) and multivariate hyperspectral features (AM-MHENet). We leveraging HybridSN and multilayer perception (MLP) to extract prominent features from the hyperspectral data of Astragalus membranaceus var. mongholicus (AMM) leaves and stems, as well as the surface and deep soil surrounding AMM roots. This methodology allows us to capture the most significant characteristics present in these hyperspectral data with high precision. The AM is subsequently used to assign weights and integrate the hyperspectral features extracted from different parts of the AMM. The MLP is then employed to simultaneously estimate the chlorophyll content (CC) and nitrogen content (NC) of AMM leaves. Compared with estimation networks that utilize only hyperspectral data from AMM leaves as input, our proposed end-to-end AM-MHENet demonstrates superior estimation performance. Specifically, AM-MHENet achieves an R2 of 0.983 with an RMSE of 0.73 for the estimation of CC in AMM leaves. For NC estimation, AM-MHENet achieves an R2 value of 0.977 with an RMSE of 0.27. These results underscore AM-MHENet’s effectiveness in significantly enhancing the accuracy of both CC and NC estimation in AMM leaves. Moreover, these findings indirectly suggest a strong correlation between the development of AMM leaves and stems, as well as the surface and deep soil surrounding the roots of AMM, and directly highlight the ability of AM to effectively focus on the relevant spectral features within the hyperspectral data. This findings from this study could offer valuable insights into the simultaneous estimation of multiple chemical parameters in plants, thereby making a contribution to the existing body of research in this field.

Background/Objectives: Patient positioning during surgery can influence intra- and postoperative complications. Therefore, we assessed the impact of the sitting and park-bench positions on anesthetic parameters and complications in neurosurgical patients. Methods & Patients: For this retrospective study, 314 adults who underwent neurosurgical procedures for posterior fossa pathologies were divided into two groups: sitting (n=231) and park bench (n=83). The following data were collected, monitored, recorded and compared: age, sex, tumor type, surgical approach, cardiovascular and respiratory complications, and postoperative surgical complications. The association of hypotension with position was further investigated through multivariate logistic regression models by adjusting for CO2 decrease, desaturation and documented gas embolism. Results: The average age was significantly lower in the sitting group (55 years, interquartile range (IQR)=43-63; female proportion=59.74%) than in the park-bench group (62 years, IQR=45-74; female proportion=57.83%) (p<0.001). Cerebellopontine angle tumors were detected in 37.23% of the patients who underwent operation in the sitting position and in 7.26% who underwent operation on in the park-bench position (p<0.001). Patients in the sitting position had significantly greater anesthetic complication (91.77% vs. 71.08%, p<0.001), hypotension (61.9% vs. 16.87%),and >2-mmHg CO2 decrease (35.06% vs. 15.66%, p<0.001) incidences. Hypoxemia and death occurred more frequently in the park-bench group (8.43% vs. 1.73% and 6.03% vs. 1.3%, respectively). Conclusions: Compared with the park-bench position, the sitting position was associated with a greater specific anesthetic complication incidence and lower postoperative mortality rate, indicating a need for careful risk‒benefit assessment when selecting each individual patient’s surgical position.

Estimating the vehicle crashworthiness parameters experimentally is expensive and time consuming. For these reasons different modelling approaches are utilized to predict the vehicle behaviour and reduce the need for full-scale crash testing. The earlier numerical methods used for vehicle crashworthiness analysis were based on the use of lumped parameters models (LPM), a combination of masses and nonlinear springs interconnected in various configurations. Nowadays, the explicit nonlinear finite element analysis (FEA) is probably the most widely recognized modelling technique. Although informative, finite element models (FEM) of vehicle crash are expensive both in terms of man-hours put into assembling the model and related computational costs. A simpler analytical tool for early analysis of vehicle crashworthiness could greatly assist the modelling and save time. In this paper a simple piecewise LPM composed of a mass-spring-damper system, is used to estimate the vehicle crashworthiness parameters, focusing on the dynamic crush and the acceleration severity index (ASI). The model is first calibrated against a full-scale crash test and a FEM, post-processed with the LS-DYNA software, at an impact velocity of 56 km/h. The genetic algorithm is used to calibrate the model by estimating the piecewise lumped parameters (stiffness and damping of the front structure of the vehicle). After calibration, the LPM is applied to a range of velocities (40, 48, 64 and 72 km/h). The predictions for crashworthiness parameters from the LPM were compared with the predictions from the FEA and the results are much similar. It is shown that the LPM can assist in crash analysis, since LPM has some predictive capabilities and requires less computation time in comparison with the explicit nonlinear FEA.

Weight loss solutions are on the rise, and there is growing interest in natural alternatives to the pharmaceuticals in the market, which are not devoid of relevant side effects. To this end, the objective of the current study is to assess the effects of a botanical-based blend comprised of lemon verbena and hibiscus extracts in weight management, body fat, appetite, lipid, and glucose profiles, in an overweight population, for 90 days. As a result, the volunteers presented significant weight loss in absence of diet, which coincided with decreased body fat. Body fat was assessed by anthropometry, electrical bioimpedance and DEXA scan. Cholesterol levels were also significantly decreased. Satiety assessment revealed that the product contributed to increased feeling of fullness and satisfaction after a meal, compared to the placebo group, which could contribute to the weight loss observed. Blood glucose and blood pressure levels remained unchanged, which was expected as the volunteers were normoglycemic and their blood pressure was in the healthy range. In conclusion, daily supplementation of a botanical-based blend contributes to weight loss in overweight individuals, in absence of diet, while not affecting other parameters that are in the healthy range. This product could be a candidate alternative or add-on to other weight loss products, as part of a healthy lifestyle.

Extreme Ultraviolet (EUV) photolithography process, is a cornerstone of semiconductor manufacturing and operates under demanding precision standards realized via nanometer-level overlay (OVL) error modeling. This procedure allows the machine to anticipate and correct OVL errors before impacting the wafer, thereby facilitating near-optimal image exposure while simultaneously minimizing the overall OVL error. Such models are usually high dimensional and exhibit rigorous statistical phenomena such as collinearities that play a crucial role in the process of tuning their parameters. Ordinary Least Squares (OLS) is the most widely used method for parameters tuning of Overlay models but in most cases it fails to compensate for such phenomena. In this paper we propose the usage of Ridge Regression, a widely known Machine Learning (ML) algorithm especially suitable for datasets that exhibit high multicollinearity. The proposed method has been applied in perturbed data from a 300 mm wafer fab and the results show reduced residuals when ridge regression is applied instead of OLS.

Efforts to optimize the design and enhance the efficiency of standing-wave thermoacoustic refrigerators (SWTAR), particularly those with parallel plate stacks, are crucial for achieving rapid and straightforward engineering estimates. This study primarily focuses on optimizing the Coefficient of Performance (COP) by combining the linear thermoacoustic theory (LTT) with the Design of Experiments (DOE) approach. The investigation centers around five key parameters affecting the COP, once the working gas is selected. Then, based on the LLT theory, the COP was estimated numerically, over defined intervals of those five parameters. Moreover, through quantitative and qualitative effect analyses, these five parameters and their interactions are determined. Utilizing a transfer function and surface response analyses based on the COP, the study aims to delineate the best COP value as well as the contribution of the thermoacoustic parameters and their interactions. Furthermore, a comparison between contour and surface responses and several statistical decision approaches applying the Full Factorial Design verify the robustness of the study’s findings. Ultimately, the COP results obtained align with existing literature, underscoring the validity and relevance of the study’s methodologies and conclusions.

Abstract: Field studies with large-stemmed plants Artemisia dubia (wormwood) have been carried out at Vėžaičiai Branch LAMMC since 2018. According to three years of experimental results, annual dry matter (DM) yield varied from 7.94 to 10.14 t ha-1. Growing conditions, nitrogen ap-plication level and harvesting time had significant impacts on Artemisia dubia productivity. This article presents the results of research on preparation and use of Artemisia dubia biomass for en-ergy conversion and evaluation of technological-technical and environmental parameters of these plants utilization for solid biofuel. For experiments were used 6 variants of Artemisia dubia samples, which were grown in 2021: plants were cut three times and two fertilization options were used: (1) no fertilization and (2) fertilization with 180 kg ha-1 of nitrogen fertilizer. These harvested plants were chopped, milled and were pressed into the pellets. The physi-cal-mechanical characteristics (mоisture content, density and strength) of Artemisia dubia pellets were investigated. During this study, it was found that the density in dry mass (DM) of pellets ranged from 1119.86 to 1192.44 kg m-3. The pellet moisture content ranged from 8.80 to 10.49%. After testing of pellet strength, it was found that the pellets which were made from plant bio-mass PK-1-1, were the most resistant to compression, they withstood 560.36 N of pressure. Dry fuel lower heating value (LHV) of pellets was sufficiently high and was very close to pine saw-dust pellets, it varied from 17.46±0.25 MJ kg-1 to 18.14±0.28 MJ kg-1. The ash content of burned pellets ranged from 3.62±0.02% to 6.47±0.09%. Emissions of harmful pollutants – CO2, CO, NOx and unburnt hydrocarbons (CxHy) did not exceed the maximum permissible levels. Summariz-ing the results of investigated properties, cоmbustion and emissiоns of Artemisia dubia pellets, it can be concluded that this biofuel can be used for production of pressed biofuel and it is charac-terized by sufficient high quality, efficient combustion and permissible emissions to the envi-ronment.

Directed energy deposition (DED) parameters were determined for near-β alloy Ti-55511 by employing statistical design of experiments (DOE) methods. Parameters resulting in fully dense freeform deposits were identified using two sequential DOEs. Single laser tracks were printed with several laser power, traverse rate, and powder feed rate settings in an initial DOE to identify promising build parameters. Capture efficiency and effective deposition rate were used to characterize and rank the single track deposits. The best parameters were then used to print solid cube with various X-Y and Z-overlaps (different hatch spacing, HS, and layer thickness, ZS) in a second DOE. Suitable deposition parameters were selected based on cube density and microstructure and were used to fabricate larger tensile samples for mechanical testing. Multiple parameter sets were found to provide dense Ti-55511 deposits with acceptable mechanical properties and parametric models showed statistical significance.

Background/Objectives: Multisystem Inflammatory Syndrome in children (MIS-C) is a rare but severe post-infectious complication of COVID-19, that often requires admission to the Pediatric Intensive Care Unit (PICU). The present study aimed to compare the demographic, clinical and laboratory characteristics between children diagnosed with MIS-C who were admitted to the PICU or did not require PICU admission. Methods: Children diagnosed with MIS-C from September 2020 to April 2023 were included in this case-control study. Patient’s demographic, clinical and laboratory data, were collected from medical records. Results: Fifty children with MIS-C were included in the study [median (IQR) age: 7.5 (4.3, 11.4) years, 28/50 (56%) males]. Twenty-two (22/50, 44%) children required admission to the PICU. In the multivariate regression analysis, hepatic (OR:12.89, 95%CI: 1.35-123.41, p-value=0.03) and cardiological involvement (OR:34.55, 95%CI: 2.2-541.91, p-value=0.01) were significantly associated with hospitalization at the PICU. Regarding the laboratory and imaging parameters during the first 48 hours from admission, D-dimer levels higher than 4μg/mL and decreased Left Ventricular Ejection Fraction were associated with an increased risk of PICU admission (OR:7.95, 95%CI:1.48-42.78, p-value=0.02 and OR=1.28, 95%CI:1.07-1.53, p-value=0.01). Children who were admitted to the PICU were more likely to develop complications during their hospitalization (10/22, 45.5% vs. 3/28, 10.7%, p-value=0.005) and were hospitalized for more days, than children in the pediatric wards (median length of stay (IQR): 20 (15,28) days vs. 8.5 (6, 14) days, p-value&lt;0.001). Conclusions: In the present study, cardiovascular, hepatic involvement and increased D-dimer levels in children with MIS-C were associated with admission to the PICU.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

Advanced-Differential Interferometric SAR (A-DInSAR) has been used to monitor surface deformations in open pit mines and tailings dams. In this paper, ground deformations have been detected on the area of the tailings Dam-I at the Córrego do Feijão Mine (Brumadinho, Brazil) before its catastrophic failure occurred on 25 January 2019. Two techniques optimized for different scattering models, SBAS (Small BAseline Subset) and PSI (Persistent Scatterer Interferometry), were used to perform the analysis based on 26 Sentinel-1B images in IW mode, acquired on descending orbits from 03 March 2018 to 22 January 2019. A WorldDEM DSM product was used to remove the topographic phase component. The results provided by both techniques showed a synoptic and informative view of the deformation process affecting the study area, with a detection of persistent trend of deformations on the top, middle and bottom sectors of the dam face until its collapse, as well as the expected natural settlements on the tailings. It is worth noting the detection of an acceleration in the displacement time-series for a short period near the failure. The maximum accumulated displacements detected along the downstream slope face were -39 mm (SBAS) and -48 mm (PSI). It is reasonable to consider that Sentinel-1 would provide decision makers complementary motion information to the in-situ monitoring system for risk assessment and for a better understanding of on-going instability phenomena affecting the tailings dam.

Fused deposition modeling (FDM) is a rather new technology in the production of personalized dosage forms. Melting and printing of polymer–active pharmaceutical ingredient (API) – mixtures can be used to produce oral dosage forms with different dosage as well as release behavior. This process is utilized to increase the bioavailability of pharmaceutically relevant active ingredients that are poorly soluble in physiological medium by transforming them into solid amorphous dispersions (ASD). Release from such ASDs is expected to be faster and higher compared to the raw materials and thus enhance bioavailability. Printing directly from powder while forming ASDs was realized. Different techniques to change release patterns as well as a non-destructive way for determination of API distribution were shown. By measuring the melt viscosities of mixtures printed a rheological model for the printer used is proposed.

Background and Aims: Sustained virologic response (SVR) lead to the decrease of portal hypertension, the regression of fibrosis, the improvement of the hepatic synthesis of procoagulant and anticoagulant factors. We aimed to assess the influence of SVR on coagulation parameters in HCV cirrhotic patients treated with DAAs. Methods: We performed a prospective study in the Institute of Gastroenterology and Hepatology Iasi, Romania, between January 2022 and February 2024. We included patients diagnosed with compensated and decompensated HCV-related liver cirrhosis, treated with direct antivirals (PrOD ± RBV or SOF/LED ± RBV) for 12/24 weeks. Blood samples for biochemical, immunological and coagulation tests were collected at baseline, EOT and SVR12/24. Results: We analyzed a group of 52 patients with HCV-related liver cirrhosis, predominantly female (68.0%), the degree of severity of cirrhosis placed the patients mainly in Child-Pugh classes B (40%) and C (36%). All patients achieved SVR. The MELD score decrease at EOT (13.48 ± 4.273; p =0.001), and SVR (9.88 ± 2.774; p = 0.000), compared to baseline (14.92 ± 4.707). Fibroscan values decreased at SVR (17.596 ± 3.7276; p = 0.000) compared to baseline (26.068 ± 7.0954). For all common coagulation parameters (platelets, INR, PT, fibrinogen, aPTT) there was a trend towards improvement during treatment, changes that were statistically significant for the majority of patients. Factor II low at baseline (75.40 ± 7.506), increases at EOT (87.40 ± 9.587), and later at SVR (99.12 ± 11.695; p = 0.000). FVIII values increased at baseline (175.52 ± 16.414) decrease at EOT (151.48 ± 13.703) and SVR (143.40 ± 13.937). FvW values decreased during treatment (146.84 ± 9.428 – baseline, 141.32 ± 9.690; p =0.000 – EOT, 126.68 ± 17.960 – SVR). In regards to the anticoagulant factors (PC, PS, ATIII), a significant improvement was brought on by SVR. Advanced stages of liver disease showed the most diminished FII activity, while at baseline and in Child-Pugh C patients we recorded the highest values of FVIII and FvW. Conclusions: Our study proved that the “reset” of the coagulopathy might be due to the improving of the liver function due to viral eradication secondary to AAD therapy.

The biodegradability of water hyacinth for biogas and biofertiliser production was studied under mesophilic conditions. The effects of water hyacinth pre-treatments were also included in this investigation. It was found that water hyacinth has a low biodegradability of 27% when monodigested while at a 3:1 ratio with cow manure, the biodegradability increases to 46%. At this elevated biodegradability, the water hyacinth biomethane potential was 185 LCH4/kgVS, while that of cow manure was 216 LCH4/kgVS. The Gompertz kinetic model had superior parameters than the Logistic model for most of the water hyacinth-cow manure combined substrate digestion. Based on the Gompertz model, the lag phase and daily maximum methane production rate were 5.5 days and 22.9 ml /day respectively for the 3:1 codigestion (R2 of 0.99). These values were 6.7 days and 15.2 ml/day respectively, in the case of water hyacinth monodigestion (R2 = 0.996). The dominant microbial species detected in the digestates were Bacteroidetes and Proteobacteria. A few microbial species were indigenous to water hyacinth but a more diverse consortia which is key to efficient substrate biodegradation, came from cow manure. The digestate contained ammonium nitrogen at 68 mg/kg with phosphorous and potassium at 73 and 424 mg/kg respectively. Nitrogen was lower but phosphorous and pottasium were comparable to previously studied digestates of other substrates. Only water hyacinth pretreated through aerobic composting proved to unlock a higher methane yield that matched a 3:1 codigestion with cow manure. Other pretreatments induced better biodegradation performance than that observed on untreated water hyacinth but this improvements were not as good as that of the 3:1 codigestion scheme. It was concluded that water hyacinth sourced from the Hartbeespoort dam, could be treated through anaerobic digestion to recover biogas and biofertilizer. However, more experiments are required to fully understand and harness the optimisation opportunities available in applying this technology to manage water hyacinth.

Attention-deficit/hyperactivity disorder (ADHD) is a common neurodevelopmental disorder. Given the growing evidence of gut microbiota being involved in psychiatric (including neurodevelopmental) disorders, we aimed to identify differences in gut microbiota composition between participants with ADHD and controls and to investigate the role of the microbiota in inattention and hyperactivity/impulsivity. Fecal samples were collected from 107 participants (NADHD=42; Ncontrols=50; NsubthreholdADHD=15; range age: 13-29 years). The relative quantification of bacterial taxa was done using 16S ribosomal RNA gene amplicon sequencing. Beta-diversity revealed significant differences in bacterial composition between participants with ADHD and healthy controls, which was also significant for inattention, but showing a trend in case of hyperactivity/impulsivity only. Ten genera showed nominal differences (P < 0.05) between both groups, of which seven genera were tested for their association with ADHD symptom scores (adjusting for age, sex, body mass index, time delay between feces collection and symptoms assessment, medication use and family relatedness). Our results show that variation of a genus from the Ruminococcaceae family (Ruminococcaceae_UCG_004) is associated (after multiple testing correction) with inattention symptoms, and suggest a role of gut microbiota in ADHD pathophysiology.

Fused deposition modeling (FDM) is widely applied in various fields due to its affordability and ease of use. However, it faces challenges such as achieving high surface quality, precise dimensional tolerance and overcoming anisotropic mechanical properties. This paper analyzes and compare the machinability of 3D printed PLA, PETG and carbon fiber reinforced PETG focusing on surface roughness and burr formation. A design of experiments (DoE) with a full factorial design was used, considering three factors: rotation speed, feed rate and depth of cut. Each factor had different levels: rotational speed at 3000, 5500 and 8000 rpm; feed rate at 400, 600 and 800 mm/min; and depth of cut at 0.2, 0.4, 0.6, and 0.8 mm. Machinability was evaluated by roughness and burr height using a profilometer for all the materials under the same milling conditions. To evaluate the statistical significance of the influence of various processing parameters on surface roughness and burr formation in 3D printed components made of three different materials PLA, PETG and carbon fiber reinforced PETG, an analysis of variance (ANOVA) test was conducted. This analysis investigated whether variations in rotational speed, feed rate and depth of cut resulted in measurable and significant differences in machinability results. Results showed that milling parameters significantly affect roughness and burr formation, with optimal conditions for minimizing any misalignment highlighting the trade-offs in parameter selection. These results provide insights into the post-processing of FDM-printed materials with milling, indicating the need for a balanced approach to parameter selection based on application-specific requirements.

Background: beta blockers of three generations are first-line drugs in the treatment of chronic heart failure (CHF). However, to date there is no clear understanding of the effect of beta blockers on myocardial energy metabolism disorders in CHF. The aim of the study: to conduct a study of beta-blockers of different generations on myocardial energy metabolism in the experimental CHF. Methods: CHF was modeled in white outbred rats by administering doxorubicin. The study drugs were administered intragastrically – new drug Hypertril (1-(β-phenylethyl)-4-amino-1,2,4-triazolium bromide)-3.5 mg/kg, metoprolol - 15 mg/kg, Nebivolol -10 mg/kg, Carvedilol 50 mg/kg, Bisoprolol, 10 mg/kg. In the myocardium, the main indices of energy metabolism were determined - ATP, ADP, AMP, malate, lactate, pyruvate, succinate dehydrogenase (SDH) activity, NAD-dependent malate dehydrogenase (NAD-MDH) activity. Results: traditional second-generation beta-blockers (Metoprolol and Bisoprolol) did not affect the studied indices of energy metabolism, and third-generation beta-blockers with additional properties - Carvedilol and, especially, Nebivalol and Hypertril improved myocardial energy metabolism. Conclusions: obtained results will help to expand our understanding of the effect of beta-blockers of various generations used to treat cardiovascular diseases on energy metabolism, and are also an experimental justification for the practical choice of these drugs in the complex therapy of CHF.

Background: The increasing prevalence of severe obesity among children and adolescents poses a significant challenge for pediatricians and general practitioners. This study aimed to investigate the relationships between biochemical results, anthropometry, blood pressure measurements and bioimpedance analysis (BIA)-derived parameters, to identify potential cardiometabolic complications associated with severe obesity. Methods: The study included 347 children (162 boys, 185 girls) aged 0-19 years, meeting criteria for severe obesity based on BMI thresholds for different age groups. Patients were recruited in four pediatric endocrinology centers in Poland (Zabrze, Cracow, Rzeszow, Szczecin). Each participant underwent anthropometric measurements, pubertal stage assessment, blood pressure measurement, biochemical and hormonal tests and BIA. Results: BMI showed significant associations with fat mass percentage (FM%) and waist-to-height ratio (WHtR), but not waist-to-hip ratio (WHR). The relationship between BMI and FM% was stronger in girls and prepubertal children. Metabolic syndrome (MetS) Z-score showed a strong positive correlation with BMI in pubertal children. Negative correlation between HDL and triglycerides was observed only in boys. Prepubertal children exhibited more significant correlations despite a smaller sample size and shorter duration of obesity. Conclusions: Considering multiple parameters beyond BMI alone provides a better understanding of cardiometabolic risks associated with severe obesity in children. MetS Z-score was not a reliable indicator of increased cardiometabolic risk in younger children. Early-onset severe obesity was associated with a higher risk of metabolic complications. Early intervention is crucial to mitigate metabolic complications in this population.

The deformation monitoring information of concrete dams contains some high-frequency com-ponents, and the high-frequency components are strongly nonlinear, which reduces the accuracy of dam deformation prediction. In order to solve such problems, this paper proposes a concrete dam deformation monitoring model based on empirical mode decomposition (EMD) combined with wavelet threshold noise reduction and sparrow search algorithm (SSA) optimization of long short-term memory network (LSTM). The model uses EMD combined with wavelet threshold to decompose and denoise the measured deformation data. On this basis, the LSTM model based on SSA optimization is used to mine the nonlinear function relationship between the reconstructed monitoring data and various influencing factors. The example analysis shows that the model has good calculation speed, fitting and prediction accuracy and it can effectively mine the date char-acteristics inherent in the measured deformation, and reduce the influence of noise components on the modeling accuracy.

Herein, we examined the effects of weather parameters and individual clinicodemographic risk factors on hemorrhagic stroke (HS) incidence, severity on admission, and disability at discharge in a harsh desert climate. In a retrospective design we studied patients admitted to a stroke unit in Arab Emirates in 2016-2019. With a distributed lag nonlinear model we explored immediate and delayed effects of weather on stroke incidence. Supervised machine learning was used to build models predictive of scores in NIHSS and mRS scales. We assessed model performance by calculating ROC AUC, F1 scores, specificity, and sensitivity. HS risk increased after a significant change in any weather parameter. The risk was reduced below baseline after 1-week adjustment to environmental changes. Climate input from the previous 3 days yielded reliable classification models. Humidex was a better predictor of severity than air temperature, whereas body mass index, age, and time of day at stroke onset were the strongest clinical predictors. Weather parameters before admission were stronger predictors of disease severity than individual clinical factors. We addressed limitations of previous studies by analyzing a full set of climate parameters: ambient temperature, relative humidity, humidex, atmospheric pressure, and wind speed. Predictive models may help to optimize patient management and develop preventative strategies.

The assessment of ecosystem quality and the maintenance of optimal ecosystem function requires understanding vegetation area dynamics and its relationship with climate variables. This study aims to detect vegetation area changes over a downstream dam and to understand the influence of the dam as well as climatic variables on the region’s vegetation areas. The case study is located in an arid area with an average rainfall amount of 50 to 100 mm/year. An analysis of seasonal changes in vegetation areas was conducted using the Normalized Difference Vegetation Index (NDVI), and supervised image classification was used to evaluate changes in vegetation areas using Landsat imagery. Pearson correlation and multivariate linear regression were used to assess the response of local vegetation areas to both hydrologic changes due to dam construction and climate variability. The NDVI analysis reveals a considerable vegetation decline after the dam construction in the dry season. This is primarily associated with the impoundment of the seasonal water by the dam and the increase in cropland areas due to dam irrigation. A significantly stronger correlation between vegetation changes and precipitation and temperature variations is observed before the dam construction. Furthermore, multivariant linear regression was used to evaluate the variations of equivalent water thickness (EWT), climate data, and NDVI before and after the dam construction. The results suggest that 85 percent of the variability in the mean NDVI was driven by climate variables and EWT before the dam construction. On the other hand, it was found that only 42 percent of the variations in NDVI were driven by climate variables and EWT after the dam construction for both dry and wet seasons.

As paradigm of complex behavior, Self-organized Criticality (SOC) reflects the ability of nonequilibrium dynamical systems to self-adjust into metastable states that are scale independent. The goal of this report is to tentatively show that the hierarchy of Standard Model masses and mixing angles follows from the universal scaling attributes of SOC.

Photothermal therapy (PTT) can overcome cancer treatment resistance by enhancing cell membrane permeability, facilitating drug accumulation, and promoting drug release within the tumor tissue. Iron oxide nanoparticles (IONPs) have emerged as effective agents for PTT due to their unique properties and biocompatibility. Approved for the treatment of anemia, as MRI contrast agents, and as magnetic hyperthermia mediators, IONPs also offer excellent light-to-heat conversion and can be manipulated using external magnetic field for targeted accumulation in specific tissues. Optimizing parameters such as laser wavelength, power density, shape, size, iron oxidation state, functionalization, and concentration is crucial for IONPs effectiveness. In addition to PTT, IONPs enhance other cancer treatment modalities. They improve tumor oxygenation enhancing the efficacy of radiotherapy and photodynamic therapy. IONPs can also trigger ferroptosis, a programmed cell death pathway mediated by iron-dependent lipid peroxidation. Their magneto-mechanical effect can exert mechanical force on cancer cells to destroy tumors, minimizing damage to healthy tissues. This review outlines strategies for managing photothermal performance and PTT efficiency with iron oxide nanoparticles, as well as synergies with other cancer therapies.

Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

Aluminium matrix composite’s overall quality is impacted by the friction stir process parameters, which have a major impact on the microstructure, soundness, and particle dispersion inside the stir zone. Although it requires a lot of experimentation, optimizing these factors is vital. For the purpose of optimizing the ultimate tensile strength and microhardness of the AA5083/Silicon carbide and AA5083/Coal composites fabricated by FSP, this work used the Taguchi L9 design of experiments. Three process parameters were investigated at three levels each. For the AA5083/Silicon carbide composite, the results of the ANOVA analysis showed rotational speed has a larger impact on ultimate tensile strength while forAA5083/coal tilt angle has a larger impact on ultimate tensile strength. On the other hand, rotating speed had a greater effect on microhardness and percentage elongation of the AA5083/Coal and AA5083/Silicon carbide composite joints, according to ANOVA analysis. The need for specific process optimization for each composite was highlighted by the fact that different combinations of parameters were best for obtaining the necessary attributes in the AA5083/Silicon carbide and AA5083/Coal composites.

Rapid draw-down in an earthfill dam has serious implications for dam safety regarding slope stability. The evaluation of reservoir draw-down impact on slope stability was carried out considering the case study of 8 hours of rapid draw-down of the Middle Marsyangdi Hydroelectric Power Project (MMHPP) rock-fill dam using the Limit Equilibrium Method (LEM) and stress-based Finite Element Method (FEM). The time-dependent factor of safety (FOS) was evaluated and found that the 8 hours of rapid draw-down undertaken in October 2012 for reservoir flushing was unsafe with a draw-down rate of 1.91m/h. The resulting FOS of 1.28 and 1.27 using LEM and FEM was classified as unsafe as per the US Army Corps of Engineers’ guideline, the minimum required factors of safety should be greater than 1.3. The minimum safe allowable draw-down rate of 0.76m/h for 20 hours was identified. Applying three layers of horizontal filter materials and increasing the upstream dam’s permeability provided adequate FOS results for all cases by increasing seepage discharge to reduce the destabilizing excess pore water pressure. Several gradual draw-down rates were also tested and found that FOS increases with decreased draw-down rates, as it reduces the excess pore water pressure controlled with stabilizing existing water load.

Sediment accumulation in a dam reservoir is a common happening environmental problem throughout the world. Topographic conditions, land use land cover change, the intensity of rainfall, and the soil characteristics are the major driving factors for sedimentation to occur. The effect of sedimentation in a dam reservoir is very visible in the watershed as a result of hilly topographic conditions, high rainfall intensity, thin land cover, and less soil infiltration capacity. In this paper, an integrated RUSLE and GIS technique was implemented to estimate a mean annual sediment yield based on spatial and temporal variations in Nashe dam reservoir situated in Fincha catchment, Abaya River basin, Ethiopia. Spatial and temporal estimation of mean annual sediment yield was estimated using the Revised Universal Soil Loss Equation (RUSLE) model and GIS. Historical 6-year (2014-2019) rainfall for the temporal variations and other physical factors such as soil erodibility, slope and length steepness, management and land used land cover, and support practice for spatial variations were used as sediment driving factors. The mean annual sediment yield ranges from 0 to 2712.65 t ha-1 year-1 was seen. Spatially, Very high, high, moderate, low, and very low sediment yield severity with total area coverage with 25%, 10%, 30%, 15%, and 20% in 2017, 2015, 2019, 2014, and 2018 respectively. The information about the spatial and temporal variations of the severity of sediment yield in RUSLE model has a paramount role to control the entry of sediment into the dam reservoir in this watershed. The results of the RUSLE model can also be further considered along with the watershed for planning strategies for dam reservoirs in the catchment.

This paper presents the validation of a numerical method for quantifying the physical quality parameters of apples through a comparative analysis with a traditional measurement method. The numerical method was applied to determine the parameters of batches of Kazakh apples according to standard requirements, using image analysis of apples. Five common varieties of Kazakh apples were selected: Aport Alexander, Ainur, Sinap Almatynski, Nursat and Kazakhski Yubileinyi. The geometric parameters of the apples and the percentage of red in the images were determined. The parameters of the 5 apple varieties were processed and measured both manually and digitally, revealing a close agreement between the obtained values. The developed digital method achieved high accuracy in determining the (diameters (d) and (D) in two perpendicular planes and height (h) of each apple), with maximum relative errors of 2.99% for (d), 3.03%, and 4.12% for the (h), and (D) parameters, respectively. Regression models were developed to determine and predict the mass and volume of apples via the digital method. The best results for the apple weight prediction were obtained for Sinap Almatynski variety by stepwise linear regression, and for the apple volume prediction were obtained for Nursat variety by linear regression. Regression equations for mass, volume and geometric dimensions constitute the basis for the development of a small instrument for automatically sorting apples by commercial variety.

Vitamin D deficiencies are very common in pregnant women, raising concerns about adverse health outcomes in children. This issue has hardly been studied in multiple pregnancies, the prevalence of which has been steadily increasing. Therefore, our study investigated the relationship between newborns’ anthropometric parameters and the concentration of 25(OH)D in maternal blood of women with twin pregnancies and umbilical cord blood. The study included 50 women who gave birth after the 36th week of twin gestation. 25(OH)D was determined in maternal blood collected during the antenatal period and in the umbilical cord blood of 100 newborns. Anthropometric parameters of the newborns (birth weight, length, head and chest circumference) were obtained from hospital records. Data on nutrition and lifestyle during pregnancy were collected from the patients during an interview conducted by a dietitian. No relationship between maternal and neonatal cord blood vitamin D concentrations and any of the anthropometric parameters of the newborns was found. However, only 6% of the mothers and 13% of the newborns had vitamin D deficiency (≤20 ng/mL). The type of pregnancy and maternal height were the main factors associated with neonatal size. Newborns from dichorionic pregnancies were on average 202 g heavier (p<0.001) and 1 cm longer (p=0.006) than newborns from monochorionic pregnancies. Newborns of mothers ≤ 160 cm in height had on average 206 g lower birth weight (p=0.006) and were 3.5 cm shorter (p=0.003) compared to newborns of taller mothers. Therefore, in our study, neonatal size of the twins was not related to the vitamin D status but to other factors such as the type of pregnancy and maternal height.

The aim of this study was to investigate and effect of application of different conditions of freeze-drying on the kinetics of process and the sorption properties of dried apples. Slices of apple were frozen and subjected to freezing-drying process with different combination of a shelf temperature (-20, 10, 20, 30°C) and pressure (37, 63, 103, 165 Pa). During the freeze-drying, the temperature in the centre of material was recorded. The moisture content in dried material and changes of water content dried apples stored at humidity of 75.3% were obtained. The Midilli et al. model was used to describe drying kinetics of the freeze-drying with good fit. Drying time decreased from 660 (variant with a constant shelf temperature of 30°C, pressure 63 Pa) to 1305 minutes (variant with temperatures −20: 10: 20: 30°C, pressure 63 Pa). For this reason, the most favourable experimental parameters were: temperature of 30°C and pressure of 63 Pa. However, application of these parameters caused higher absorption of water vapour during storage. Therefore, the selection of freeze-drying parameters should also be related to the expected properties of the final product.

An adequate representation of the water infiltration process in the soil allows improving the efficiency in application and the uniformity in surface irrigation. The Green and Ampt model has shown a good representation of the process, and researchers from the United States Department of Agriculture (USDA) determined the values of their parameters for soils of that country, which are shown in tables or through functional relationships and this information is used as reference in several parts of the world, although there is no certainty that they are representative of the soils in Mexico. In this study, the parameters of the Green & Ampt equation were determined and evaluated in some soils of agricultural importance in Mexico. The parameters were obtained in four ways: one of them applied a methodology adapted from Brooks and Corey to quantify the wetting front capillary pressure head and used an permeameter under constant hydraulic head to determine the saturated hydraulic conductivity, and the other three consisted in taking them from three studies reported by the USDA. The values of the parameters suggested in Mexico drastically underestimated the results with relative errors (RE) in a range of -49.0 to -94.0% and the most representative were those obtained with the methodology proposed in this research with RE of -15.0 to 6.0%.

In cosmology, the cosmic curvature $K$ and the cosmological constant $\Lambda$ are two most important parameters, whose values have strong influence on the behavior of the universe. By analyzing the energy-momentum tensor and equations of state of ideal gas, scalar, spinor and vector potential in detail, we find that the total mass density of all matter is always positive, and the initial total pressure is negative. Under these conditions, by qualitatively analyzing the global behavior of the dynamical equation of cosmological model, we get the following results: (i) $K= 1$, namely, the global spatial structure of the universe should be a 3-dimensional sphere $S^3$. (ii) $0\le\Lambda < 10 ^ {-24} {\rm ly} ^ {-2}$, the cosmological constant should be zero or an infinitesimal. (iii) $a(t)>0$, the initial singularity of the universe is unreachable, and the evolution of universe should be cyclic in time. This means that the initial Big Bang is impossible at all. Since the matter components considered are quite complete and the proof is very elementary and strict, these logical conclusions should be quite reliable. Obviously, these conclusions will be much helpful to correct some popular misconceptions and bring great convenience to further research other problems in cosmology such as property of dark matter and dark energy.

The aim of this paper is to explore the watertightness behaviour for high pressure applications using Multijetfusion technology and polyamide 12 as a material. It reports an efficient solution for manufacturing functional prototypes and final parts for water pressure applications. It provides manufacturing rules to engineers in the pressurized product development process up to 10 MPa of nominal pressure. The research findings show manufacturers the possibility of using additive manufacturing as an alternative to traditional manufacturing. Water leakage was studied using different printing orientations and wall thickness for a range of pressure values. An industrial ball valve was printed and validated with the ISO 9393 standard also meeting tolerance requirements. This paper is a pioneering approach to the additive manufacturing of high performance fluid handling components. This approach solves the problem of leakage caused by porosity in additive manufacturing technologies

Abstract Background: Periodontitis is associated with systemic chronic inflammatory diseases. There is limited evidence on the influence of anti-cytokine therapies on the periodontal condition and microbiome in the tooth pocket of such patients, so the aim of this study was to elucidate this issue. Methods: In this observational trial, the periodontal status and the gingival crevicular fluid of 13 patients with different chronic inflammatory diseases were obtained before initiation of anti-cytokine treatment and 14 weeks after. Gingival crevicular fluid was collected for 16S rRNA gene sequencing from a clinically healthy tooth and the deepest measured pocket. Results: In participants with advanced attachment loss at baseline, the clinical attachment level significantly decreased from 2.9 (2.3-3.4) to 2.4 (1.3-3.0) mm (p = 0.04), and the bleeding- on-probing index dropped from 19.4 (10.0-21.0) to 7.3 (6.9-9.9) mm (p = 0.02) without any further periodontal treatment. Shannon’s diversity index significantly increased in the deepest pockets of patients (p = 0.039). Conclusion: The data showed alterations in diversity of the subgingival microbiome and improvement of periodontal parameters over the course of the study, implying a shift towards a healthier condition after starting anti-cytokine therapy. Additional investigations are needed to analyze whether the administration of selective biologicals can improve periodontal conditions in patients with or without chronic inflammatory diseases.

Osteoporosis is an abnormal bone remodeling condition characterized by decreased bone density, which leads to high risks of broken bones. Previous studies have demonstrated that Lycii Radicis Cortex (LRC) extract inhibits bone loss in ovariectomized (OVX) mice by enhancing the osteoblast differentiation. A bioactive compound, Kukoamine B (KB), was identified from a fractionation of LRC extract as a candidate component responsible for an anti-osteoporotic effect. This study investigated the anti-osteoporotic effects of KB using in vitro and in vivo osteoporosis models. KB treatment significantly increased the osteoblastic differentiation and mineralized nodule formation of osteoblastic MC3T3-E1 cells, while it significantly decreased the osteoclast differentiation of primary-cultured monocytes derived from mouse bone marrow. The effects of KB on osteoblastic and osteoclastic differentiations under more physiological conditions were also examined. In the co-culture of MC3T3-E1 cells and monocytes, KB promoted osteoblast differentiation but did not affect osteoclast differentiation. For the in vivo experiments, KB significantly inhibited OVX-induced bone mineral density loss and restored the impaired bone structural properties in osteoporosis model mice. These results suggest that KB may be a potential therapeutic candidate for the treatment of osteoporosis.

The application of multiple criteria decision-making (MCDM) techniques in real-life problems has increased in recent years. The need to build advanced decision models with higher capabilities that can support decision making in a broad spectrum of applications, promotes the integration of MCDM techniques with applicable systems, including artificial intelligence, and Geographic Information Systems (GIS). The Analytic Hierarchy Process (AHP) and Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) are amongst the most widely adopted MCDM techniques capable of resolving water resources challenges. A critical problem associated with water resource management is dam site selection. This paper presents a comparative analysis of TOPSIS and AHP in the context of decision making using GIS for dam site selection. The comparison was made based on geographic and water quality criteria. A ratio estimation procedure was used to determine the weights of these criteria. Both methods were applied for selection of optimal sites for dams in the Sistan and Baluchestan province, Iran. The results show that the TOPSIS method is better suited to the problem of dam site selection for this case study. Actual locations of dams constructed in the area were used to verify the results of both methods.

Chronic Myeloid Leukemia (CML) is one of the most commonly found types of myeloproliferative neoplasms, characterized by increased proliferation of granulocytic cells without losing their differentiation ability. Imatinib, a Tyrosine Kinase Inhibitor (TKI), can be effectively used as therapy for CML. However, imatinib can affect bone turnover, thus having clinical implications on the bones of CML patients undergoing long-term imatinib therapy. However, parameters that can accurately describe the bone condition in CML patients receiving imatinib still need further study. A combination of imaging techniques such as Bone Mineral Density (BMD) and bone turnover activity markers such as C-terminal telopeptide of type I collagen (CTX-1) and Osteocalcin has the potential to be used as monitoring parameters for bone density abnormalities in CML patients receiving imatinib. This article explains the rationale for using BMD, CTX-1, and Osteocalcin as monitoring parameters of bone remodeling in CML patients receiving imatinib. First, the physiological process of bone turnover will be explained. Then, we describe the role of tyrosine kinase in bone metabolism. Next, the impact of imatinib on BMD, CTX-1, and Osteocalcin will be explained. In conclusion, the assessment of bone health of CML patients on Imatinib should include both BMD tests and bone turnover marker assays such as CTX-1 and Osteocalcin.

This article explores the potential of the Unreal Engine game engine as a tool for creating highly realistic 3D visualizations of GIS data, specifically in the context of significant historical areas. The research will focus on the computational techniques used in the 3D visualization of GIS data and the Unreal Engine software and its potential applications in geomatics. The article also presents several relevant scientific studies and projects that have successfully used game engines for similar purposes, explores the potential for using GIS data within a game engine, including plug-ins that provide additional functionality to GIS software, and the use of procedural modeling to create 3D objects through the CityEngine software plug-in. Finally, the research is applied to a dataset of the historical Vltava Valley covering an area of 1670 km2 to demonstrate the capabilities of Unreal Engine in creating realistic visualizations of large historical landscapes, and the resulting visualizations are presented. This practical application of the research provides valuable insights into the potential of the Unreal Engine as a powerful tool for creating highly realistic 3D visualizations of large historical areas with potential applications in the field of geomatics.

The problem of limited water supply in the Vhembe District (Limpopo Province, South Africa) is exacerbated by a preponderance of dissolved salts, which cause disagreeable taste and odour in the water as reported by the communities using this water for drinking. The water treatment plant that supplies the treated water to the communities in the District sources this raw water from the Nandoni Dam at the Livhuvu river catchment. However, there are no scientific studies that have been reported in the literature which focused on determining the levels of water salinity from various water sources in the municipalities of the District. Water samples from various sites across the Nandoni Dam, a primary source of domestic water supply in the region, were collected during all the seasons basis over a period of twelve months in order to ascertain the concentrations of dissolved salts in the dam. Onsite analyses of the water samples were conducted using the YSI ProDSS multimeter, while the laboratory water analyses were conducted using the spectroquant and atomic absorption spectrometers. Although salinity tests seem to indicate that the water sampled across most of the Nandoni Dam is brackish during all seasons of the year with the highest being 750 mg/L, water samples from the dam mid-outlet and the treatment plant are slightly below the WHO brackish water bracket of 500 mg/L with unfavourable taste for drinking. Results from this study indicate that the water sourced from the Nandoni Dam is not suitable for human consumption and therefore requires integrated water resource management, as well as robust and cost-effective water desalination treatment.

Lap joints were friction stir welded in AA 7075-T6 at 1320 rpm and using two welding speeds: 70 mm/min and 120 mm/min. The temperature profiles of the weld zone were registered during the process; furthermore, the microhardness, tensile strength, and microstructure of the joints produced were examined. This study brings new insights into the thermomechanical behavior of the material during the process. The peak temperature obtained with the lower welding speed (70 mm/min) is 10% higher than that obtained with the higher speed (120 mm/min). Moreover, a 5% increase in microhardness and a 6% increase in tensile strength were were observed increasing the welding speed. Addition-ally, the microstructure examination demonstrated that, by decreasing the welding speed, the larger interaction between the tool and the material results in a deeper stir zone due to the increased heat diffusion downwards to the material. This heat flow affects the thermal profile and influences the resulting mechanical properties of the welded joints.

Data Extraction is a technique is called as clustering which is used to retrieve data either from the files or data bases or both. This paper focuses on the performance evaluation parameters of the clustering algorithms based on different parameters or conditions or constraints and parameters which are used to perform the clustering process to get the clusters on the data sets. Therefore best clusters are retrieved when best parameters or conditions or constraints or preferences which are applied on the data sources for the clustering process. These parameters or conditions or constraints are opted by the user called as user preferences.

In this paper, the feasibility of automated and accurate in vivo measurements of vascular parameters continuously and non-invasively using ultrasound sensor is presented. Vascular parameters such as pulse wave velocity (PWV), blood pressure (BP), arterial compliance (AC) and stiffness index (SI) are affluent indicators of cardiovascular disorders and needs to be monitored non-invasively and continuously during surgeries and follow-up procedures. Cuff based or invasive catheter techniques are considered as gold standard to measure BP and are fed manually to compute AC and SI which employ imaging algorithms. In this context, a Continuous and Non-Invasive Vascular Stiffness and Arterial Compliance Screener (CaNVAS) is developed to measure said parameters continuously and non-invasively using ultrasound sensor. Acoustic waves of 5 MHz (2.2 – 10 MHz) are driven through target arterial walls, reflected echoes captured, pre-processed and frequency shift is used to calculate PWV. It is observed that PWV measured using CaNVAS varies exponentially with BP values obtained from sphygmomanometer (BPMR-120) and this relationship is used to compute instantaneous values of BP. The proposed device is validated by performing measurements on 250 subjects in pre and post exercise conditions and found to have 95% accuracy and an average of 12.5% coefficient of variation.

Background and objectives: The impact of prenatal exposure to polycyclicaromatic 17 hydrocarbons (PAHs) on birth outcomes as weight, length, head circumference, placenta 18 weight, and Apgar. Materials and Methods: Two cohorts of children born in the years 2013 and 19 2014 in Karvina (Northern Moravia, N=144) and Ceske Budejovice (Southern Bohemia, 20 N=198), were studied for the relationship between the prenatal exposure to PAHs and growth 21 parameters up to two years of age. PAHs exposure was evaluated according to the concentration 22 of benzo[a]pyrene (B[a]P) in polluted air and monohydroxylated PAH metabolites (OH-PAHs) 23 in urine of newborns as well as their mothers. Data of growth parameters were obtained from 24 pediatric questionnaires up to 24 months. 25 Results: Concentrations of B[a]P were significantly higher in Karvina (p<0.001). OH-26 PAH metabolites were significantly higher in the mothers´ as well as in the newborns´ urine in 27 Karvina. The length was shorter in newborns in Karvina at birth (p<0.001), but this difference 28 was straightened out during next 3 to 24 months. Birth weight at the delivery did not differ 29 between newborns in Karvina and Ceske Budejovice. Newborns in both locations significantly 30 decreased their weight gain between birth and 3 months after delivery. OH-PAHs metabolites 31 in mother’s or newborn’s urine did not affect birth weight. Top 25% values of concentrations 32 of 2-OH-FLUO, 1-OH-NAP, 2-OH-NAP, 1-OH-PHEN, 2-OH-PHEN, 3-OH-PHEN, 4-OH-33 PHEN, and the sum of all-OH-PAHs higher than median in the newborns´ urine decreased their 34 length. 2-OH-PHEN top 25% of concentrations in the newborns´ urine decreased their head 35 circumference, 2-OH-FLUO, 1-OH-NAP, 2-OH-NAP, 1-OH-PHEN, 2-OH-PHEN, 3-OH-36 PHEN, 4-OH-PHEN, 9-OH-PHEN, 1-OH-PYR, and all-OH-PAHs decreased placenta weight; 37 2-OH-FLUO, 1-OH-NAP, 2-OH-NAP, 1-OH-PHEN, 2-OH-PHEN, 3-OH-PHEN, 4-OH-38 PHEN, and all-OH-PAHs decreased Apgar 5´. Conclusions: We observed that higher 39 concentration of PAHs determined as OH-PAHs metabolites in newborns´ urine decreased their 40 length, head circumference, placenta weight, and Apgar 5´, but did not affect birth weight.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

Total hip arthroplasty (THA) is a preferred treatment for primary osteoarthritis (OA) or secondary due to developmental hip dysplasia (DDH). Gait analysis is considered a golden standard for evaluating post-arthroplasty walking patterns. This study compared post-THA spatiotemporal gait parameters (SGPs) between OA and DDH patients and explored correlations with demographic and clinical variables. Thirty patients (15 per group) were recorded during gait, and their SGPs were analyzed. Functionality was evaluated with the Oxford Hip Score (OHS). The OA patients were significantly older than DDH (pr< 0.51, all p< 0.05). The preoperative gait alterations associated with OA or DDH were improved to similar levels in both groups after THA. Post-arthroplasty SGPs and OHS correlations indicate limitations in certain activities. These find-ings must be correlated with kinetic gait analysis data to fully evaluate gait and functionality dif-ferences among patient groups.

(1) Background: Grapes and their associated by-products (as grape pomace, GP) stand out for their polyphenol content, which makes them a source of bioactive compounds with antioxidant capacity. The aim of this research was to determine if the inclusion of 50 g/kg of GP in the diet of hens could enrich egg with antioxidants and to study its effect on internal and external egg quality parameters. (2) Methods: A trial was conducted with two genetic lines of hens, which were fed either a control diet or a diet containing 50 g/kg of GP. Performance, internal and external egg quality, and egg yolk content of vitamins E and A, and gallic acid were determined; (3) Results: In eggs laid by hens fed GP diet, Haugh units and yolk colour score were enhanced, and eggshell became thinner, but without affecting the breaking strength. No dietary effect was observed on vitamin contents in yolk. Higher gallic acid content was observed in yolk of eggs laid by hens fed the GP diet, suggesting that some dietary phenolic compounds could be transferred to the eggs. Hen genetics influenced egg weight, albumen Haugh units, shell thickness and α- and γ-tocopherol concentration in yolks; (4) Conclusions: Dietary inclusion of GP improved the internal quality of eggs, enriching yolks with a phenolic compound, but reduced shell thickness.