Since the introduction of Cross-laminated Timber (CLT) in Austria in the early 1990s, the adoption of this 90°-crosswise-laminated product has seen exponential growth worldwide. Compared to traditional laminated timber products (e.g. glulam), CLT provides improved dimensional stability, but with reduced out-of-plane bending stiffness. To improve the bending stiffness, while maintaining relative dimensional stability, a modified orientation of the inner layers in a diagonal direction can be used. This novel product is Diagonal-Cross-laminated Timber (DCLT), a composite timber product, consisting of inner layers which are rotated at different angle-ply orientations between 0 and 90 degrees to the outer layers. To properly model the out-of-plane bending behavior of the DCLT, analytical models and Finite Element Analysis (FEA) were used and the results were validated by third-point bending tests performed on DCLT panels with angle-ply orientations of 10°, 20°, 40°, 70°, and a conventional CLT 90° panel. The results indicate that DCLT panels with angle-ply cross-layers have a structural advantage in out-of-plane bending over traditional CLT (90°) panels. The development of DCLT and its introduction to the industry could enable the use of lower-quality timber that would not otherwise satisfy structural requirements for CLT.

As an emerging building solution, cross-laminated timber (CLT) floors have been increasingly used in mass timber construction. The current vibration design of CLT floors is conservative due to the assumption of simple support conditions in the floor-to-wall connections. It is noted that end fixity occurs as a result of clamping action at the ends, arising from the gravity load applied by the structure above the floor and by the mechanical fasteners. In this paper, the semi-rigid floor-to-wall connections are treated as elastically restrained edges against rotations to account for the effect of partial constraint. A rotational end-fixity factor was first defined to reflect the relative bending stiffness between CLT floors and elastic restraints at the edges. Then, for the design of vibration serviceability of CLT floors as per the Canadian Standard for Engineering Design in Wood (CSA O86), restraint coefficients were defined and their analytical expressions were derived for natural frequencies and the mid-span deflection under a concentrated load, respectively. In particular, a simplified formula of the restraint coefficient for the fundamental frequency was developed to assist engineers in practical design. At last, by comparing with reported experimental data, the proposed design formula showed excellent agreement with test results. In the end, the proposed end fixity factor with their corresponding restraint coefficients is recommended as an effective mechanics-based approach to account for the effect of end support conditions of CLT floors.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

As the carbon storage capacity of timber is recognized, there is growing interest in timber and wooden structures as a solution to various environmental problems. The use of Korean timber with substantial carbon storage capacity is required to reduce Korean carbon emissions and circulate timber resources. In this study, fire tests were conducted to investigate the charring properties of glued laminated timber columns made of Korean larch. The fire tests were conducted under both load-bearing and non-load-bearing conditions. The fire test results showed that the charring depth was affected by the corners of the section, and that the load ratio had an insignificant influence on the charring depth when the load ratio was 0.9 or less. This study provides data that can be used to compare the charring properties of laminated wood produced using South Korean larch with the charring properties of foreign standards. This provides reference data for developing fire-resistant design standards for timber structures made from South Korean timber.

Background: The effect of velamentous cord insertion (VCI) on perinatal outcomes in twin pregnancies is unclear due to conflicting findings. This retrospective study aimed to examine VCI prevalence and related risk factors in twin pregnancies and its association with adverse perinatal outcomes. Methods: Women with twin pregnancies who delivered between January 2012 and December 2021 in a single tertiary hospital were included. The participants were divided into dichorionic (DC) and monochorionic diamniotic (MCDA) groups, and their maternal and fetal characteristics and VCI rates were compared. Logistic regression models were used to identify risk factors for VCI and VCI-related perinatal outcomes. Results: Among the 694 twin pregnancies included in this study, the VCI rate was significantly higher in MCDA than in DC twins. Body mass index and MCDA twins were significant risk factors for VCI, whereas assisted reproductive technology pregnancy was a significant protective factor against VCI. In DC twins, VCI did not affect perinatal outcomes. Conclusion: In MCDA twins, VCI was a significant risk factor for fetal growth restriction, twin-to-twin transfusion syndrome, and preterm birth at

Background/Objectives: Women with subclinical hypothyroidism (SCH) were reported to be at an increased perinatal risk. We aimed to investigate the relationship between SCH and perinatal outcomes in singleton pregnancies resulting from assisted reproduction technology (ART). Methods: We retrospectively examined the perinatal outcomes of ART singleton pregnancies in women who underwent thyroid function screening before conception and delivered at our hospital from January 2020 to July 2023. We defined SCH as thyroid-stimulating hormone (TSH) levels <2.5 mU/L and normal free T₄ levels. The patients were divided into three groups: normal thyroid function (group A), SCH without levothyroxine therapy (group B), and SCH with levothyroxine therapy (group C). The risks of preterm birth, preeclampsia, fetal growth restriction, manual placental removal, and blood loss at delivery were compared among the three groups. Results: Out of the 650 ART singleton deliveries, 581 were placed in group A, 34 in group B, and 35 in group C. The preterm birth rate at <34 weeks was significantly higher in group B and significantly lower in group C than in group A. The rate of preterm delivery at <34 weeks increased in correlation with TSH levels. Levothyroxine therapy was the significant preventive factor for preterm birth at <34 weeks. Conclusions: The preterm birth rate before 34 weeks was significantly higher in the SCH group. Levothyroxine therapy is a significant protective factor against preterm birth before 34 weeks. Universal screening for thyroid function and appropriate hormone therapy in pregnant women may help reduce perinatal risks, including preterm birth.

Background Community infections of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) have increased rapidly since the emergence of the Omicron strain. During the eighth and ninth pandemic waves—when movement restrictions in the community were eased—the all-case registration system was changed, and the actual status of infection became uncertain. Methods We conducted regular rapid antigen tests (R-RAT) once or twice a week to examine the actual state of coronavirus disease (COVID-19) diagnosis among healthcare employees. Results Overall, 320 (1.42/day) and 299 (1.76/day) employees were infected in the eighth and ninth pandemic waves. During both periods, 59/263 doctors (22.4%), 335/806 nurses (41.6%), 92/194 administrative employees (47.4%), and 129/218 clinical laboratory technicians (59.2%) were infected. In the eighth wave, 56 of 195 employees were infected through close contact; in the ninth wave, 26 of 62 employees were infected. No significant difference was observed in the number of vaccinations between infected and non-infected employees. The positivity rate of R-RAT was 0.41% and 0.45% in the eighth and ninth waves. R-RAT detected infection in 212 and 229 employees during the eighth and ninth waves, respectively; the ratio of R-RAT-detected positive employees to those who reported infection was significantly higher during the ninth wave (odds ratio: 1.67, 95% confidence interval: 1.17–2.37, p

This study addresses the enhancement of material efficiency and reduction of brittleness in timber-to-concrete adhesive connections for beam-type timber and timber-concrete composite panels. The research explores the potential benefits of adding longitudinal timber ribs to Cross-Laminated Timber (CLT) beam-type panels. Three groups of flexure-tested specimens were analysed: (1) timber panels (1400 mm × 400 mm) with two 100 mm thick CLT panels and two 60 mm thick CLT panels reinforced with 150x80 mm timber ribs; (2) eight specimens (600 mm × 100 mm × 150 mm) with CLT members (600 mm × 100 mm × 100 mm) connected to a 50 mm concrete layer using granite chips and Sikadur-31 (AB) epoxy adhesive; (3) six CLT panels (1400 mm × 400 mm × 50 mm) bonded to a 50 mm concrete layer, with two panels containing polypropylene microfibers and two panels incorporating polyethene dowels for mechanical connection. Specimens were subjected to three-point bending tests and analysed using the transformed section method, γ-method, and finite element method with ANSYS 2023R2 software. Results indicated a 53% increase in load-carrying capacity for ribbed CLT panels with no additional material consumption, a 24.8%-41.1% increase for CLT panels strengthened with a concrete layer, and improved ductility and prevention of disintegration in timber-concrete composites with polypropylene microfibers.

Macrophages as a source and target of GDF-15

Forest resources are renewable,rational exploitation and utilization of forest resources are not only conducive to sustainable development of population, but also can obtain higher economic benefits. Based on actual timber harvesting problems,a combined harvesting model of timber and non-timber with nonlinear harvesting term was established.Firstly, using the qualitative theory of ordinary differential equations, the dynamic behavior of the model is studied, and the existence and stability of the equilibrium point of the model are proved .Secondly, the optimal control solution is obtained by using the optimal control theory.Finally, the optimal harvesting strategy of timber and non-timber products is given based on the numerical simulation results, which provides a certain theoretical basis for the sustainable development of forestry ecological economy.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

Bartonella species, intracellular parasitic zoonotic pathogens, has drawn increasing attention for their diverse host range and associated human diseases. This study investigates Bartonella infection in small mammals in Yunnan Province, China, focusing on tissue tropism. 333 small mammals were sampled from 13 species, 3 orders, 4 families, and 4 genera in Heqing and Gongshan Counties. Conventional PCR and real-time quantitative PCR (qPCR) were utilized for detection and quantification, followed by bioinformatic analysis of obtained DNA sequences. Results show a 31.5% detection rate, varying across species. Notably, Apodemus chevrieri, Eothenomys eleusis, Niviventer fulvescens, Rattus tanezumi, Episoriculus leucops, Anourosorex squamipes, and Ochotona Thibetana exhibited infection rates of 44.4%, 27.7%, 100.0%, 6.3%, 60.0%, 23.5%, and 22.2%, respectively. Genetic analysis identified 30, 10, and 5 strains based on ssrA, rpoB, and gltA genes, with nucleotide identities ranging from 92.1% to 100.0%. Bartonella strains were assigned to B. grahamii, B. rochalimae, B. sendai, B. koshimizu, B. phoceensis, B. taylorii, and a new species identified in the Episoriculus leucops (GS136). Tissue distribution analysis revealed varied copy numbers across different tissues, with the highest load in spleen. These findings underscore Bartonella's diverse species and host range in Yunnan Province, highlighting its broad tissue tropism in small mammals.

Zanthoxylum armatum is an forest tree with apomixis characteristic, and RWP-RKs are plant-specific transcription factors known to regulate nitrogen response and embryonic development. However, the genome-wide analysis of RWP-RK family genes in Z.armatum is unclear. In this study, 36 ZaRWP-RK transcription factors were identified in the genome of Z.armatum, among which 15 genes were belonged to the RKD subfamily and 21 belonged to the NLP subfamily. Duplication events of ZaRWP-RK genes were mainly segmental duplication, and synteny analysis revealed close phylogenetic relationship between Z.armatum and Arabidopsis. The analysis of cis-elements indicated that ZaRWP-RK genes may be involved in the regulation of embryonic development of Z.armatum by responding to plant hormones such as abscisic acid, auxin, and gibberellin. Real-time PCR showed that the expression levels of most ZaRWP-RK genes were significantly increased from flowers to young fruits. Protein-protein interaction network analysis further revealed the potential roles of the ZaRWP-RK proteins in apomixis. Collectively, this study provide a theoretical basis for future investigations into the ZaRWP-RK genes and their regulatory mechanisms in the apomixis process of Z.armatum.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

The unravelling of the human genome created new perceptions on the origin and evolution of diseases and for cancer in particular, it established the notion that neoplasia has been a companion of life since its ap-pearance on earth. It is not surprising that neoplasms, in various forms, develop in numerous species of animals and even in plants. Unmistakable accounts of cancer with clinical features as are understood today, begin in the 5th c. B.C. The principles and practice of the Hippocratic and Galenic tradition dominated cancer care virtually into the 20th century. Advanced sequencing technologies at the dawn of the 21st century, generate new ther-apeutic opportunities with immunotherapy, oncolytic virotherapy and gene transfer, the latter especially in cases of hereditary cancer.

Timber-concrete composite (TCC) systems join the positive aspects of engineered wood products (good seismic behaviour, low thermal conductivity, environmental sustainability, good behaviour under fire if appropriately designed) with those of concrete (high thermal inertia, durability, excellent fire resistance). TCC facades are typically composed by an internal insulated timber-frame wall and an external concrete slab, separated by a ventilated air cavity. However, there is very limited knowledge concerning the performance of TCC facades, especially for what concerns their thermal behaviour. The present paper deals with the development and optimisation of a 2D CFD model for the analysis of TCC ventilated façades thermal behaviour. The model is calibrated and validated against the experimental data collected during the annual monitoring of a real TCC ventilated envelope in the north of Italy. Also, a new solver algorithm is developed to significantly speed up the simulation. The final model can be used for the time-efficient analysis and optimisation of the thermal performance of TCC ventilated facades, as well as other ventilated facades with external massive cladding, avoiding the expensive and time-consuming construction of mock-ups, or the use of comparably slow (conventional) CFD solvers that are less suitable for optimization studies.

Glaucoma is one of the primary causes of blindness worldwide. Canal opening surgery, a type of minimally invasive glaucoma surgery (MIGS) applied in cases of mild to moderate glaucoma, has gained increasing popularity in recent years due to its efficacy in reducing intraocular pressure, its safety profile, the simplicity of its technique, and the reduced likelihood of compromised vision. Nevertheless, the existing body of histopathological studies remains insufficient for a comprehensive understanding of post-surgical wound healing. Consequently, debates persist among researchers regarding the mechanism through which Schlemm’s canal opening surgery reduces intraocular pressure, as well as the surgical techniques that may impact the outcomes and the factors influencing surgical success. As the history of MIGS is relatively short and lacks sufficient systemic reviews or meta-analysis evaluating the influence of individual factors, this review was conducted to illuminate disparities in the researchers’ opinions at the current stage of research.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

Natural vegetation restoration can take decades to achieve and requires information on species composition and trend to inform management strategies. Here we demonstrate the potential and portability of drone, dove and Sentinel-2 imagery for species level classification and trajectory monitoring using three study sites with different revegetation histories. Drone imagery (4 cm) was classified using random forests. Dove (3 m) and Sentinel-2 (10 m) images were acquired close to the anniversary of the drone flights and converted into fractional cover maps showing the proportion of exotics, natives and other land covers using ordinary least squares (OLS) and geographically weighted regression (GWR). The time series of fractional cover maps were converted into positive and negative slope and second-order curvature and summarised as one RGB composite to illustrate trend and observe exotic expansion. Drone classification accuracies ranged from 73%-76% when applied to the full plant species list and between 93% and 97% when grouped into natives, exotics, and other land covers. GWR outperformed OLS for all fractional cover mapping and GWR with dove imagery was more accurate than with Sentinel imagery. The combination of very high-resolution drone acquired imagery with the versatility of dove acquired imagery arms land managers with highly accurate species composition and their spatio-temporal dynamics to promote timely intervention.

The study addresses the fabrication of indium aluminum nitride (InAlN) layers by DC co-sputtering at room temperature, highlighting their potential in optoelectronic and solar cell applications. Experiments were carried out with different powers for the aluminum target, observing changes in the stoichiometry and material properties. XPS and AES analysis confirmed the variation in indium and aluminum concentration, directly affecting bandgap and electrical properties such as mobility and free carrier concentration. The layers showed smooth surfaces with low roughness, suitable for high efficiency interfaces. This method promises to reduce costs and improve the accessibility of efficient solar technologies based on InAlN semiconductor alloy.

We study the Gaudin models with gl(1|1) symmetry that are twisted by a diagonal matrix and defined on tensor products of polynomial evaluation gl(1|1)[t]-modules, extending all the results of to the twisted case. Namely, we give an explicit description of the algebra of Hamiltonians (Gaudin Hamiltonians) acting on tensor products of polynomial evaluation gl(1|1)[t]-modules and show that there exists a bijection between common eigenvectors (up to proportionality) of the algebra of Hamiltonians and monic divisors of an explicit polynomial written in terms of the highest weights and evaluation parameters. In particular, our result implies that each common eigenspace of the algebra of Hamiltonians has dimension one. We also give dimensions of the generalized eigenspaces.

The many limitations of implementing anticancer strategies under the term “precision oncology” have been extensively discussed. While some authors propose promising future directions, others are less optimistic and use phrases such as illusion, hype and false hypotheses. The reality is revealed by practicing clinicians and cancer patients in various online publications, one of which has stated that “in the quest for the next cancer cure, few researchers bother to look back at the graveyard of failed medicines to figure out what went wrong.” The message is clear: novel therapeutic strategies with catchy names (e.g., synthetic “lethality”) have not fulfilled their promises despite decades of extensive research and clinical trials. The main purpose of this review is to discuss key challenges in solid tumor therapy that surprisingly continue to be overlooked by the nomenclature committee on cell death and numerous other authors. These challenges include: the impact of chemotherapy-induced genome chaos (e.g., multinucleation) on resistance and relapse, oncogenic function of caspase 3, cancer cell anastasis (recovery from late stages of apoptosis), and pitfalls of ubiquitously used preclinical chemosensitivity assays (e.g., cell “viability” and tumor growth delay studies in live animals) that score such pro-survival responses as “lethal” events. Studies outline herein underscore the need for new direction in the management of solid tumors.

Numerous approaches address over-fitting in neural networks: by imposing a penalty on the parameters of the network (L1, L2, etc); by changing the network stochastically (drop-out, Gaussian noise, etc.); or by transforming the input data (batch normalization, etc.). In contrast, we aim to ensure that a minimum amount of supporting evidence is present when fitting the model parameters to the training data. This, at the single neuron level, is equivalent to ensuring that both sides of the separating hyperplane (for a standard artificial neuron) have a minimum number of data points — noting that these points need not belong to the same class for the inner layers. We firstly benchmark the results of this approach on the standard Fashion-MINST dataset, comparing it to various regularization techniques. Interestingly, we note that by nudging each neuron to divide, at least in part, its input data, the resulting networks make use of each neuron, avoiding a hyperplane completely on one side of its input data (which is equivalent to a constant into the next layers). To illustrate this point, we study the prevalence of saturated nodes throughout training, showing that neurons are activated more frequently and earlier in training when using this regularization approach. A direct consequence of the improved neuron activation is that deep networks are now easier to train. This is crucially important when the network topology is not known a priori and fitting often remains stuck in a suboptimal local minima. We demonstrate this property by training a network of increasing depth (and constant width): most regularization approaches will result in increasingly frequent training failures (over different random seeds) whilst the proposed evidence-based regularization significantly outperforms in its ability to train deep networks.

Forest enterprise has been identified as a means of generating income among people; plays a vital role in enhancing the quality of life of forest-dependent people. Despite the opportunities timber marketing offers the people, the disparities in the income generation of the marketers in the Bodija sawn wood Market and the effect of socio-economic factors on income generation of the marketers is not well understood. This study was conducted to assess the socio-economic determinants of contributions of timber marketing to the income of timber merchants in Bodija sawn-wood Market. One hundred structured questionnaires were administered randomly in five zones of the sawn wood Market to obtain information on the socio-economic background of the sawn wood marketers and the contribution of timber trade to their incomes. The result indicated that 99.0% of the respondents were male while females constituted 1.00%. Seventy-five percent of the marketers had post-primary education and 25% had primary education. Two percent of the marketers had below 10 years of marketing experience, twenty-six percent had between 11 and 20 years, 57.00% had between 21 and 30 years, and 15.00% had more than 30years experience. Fifty-eight percent of the respondents earned between ₦10000-₦60000 (1US$ = 360.00) from timber marketing, thirty-one percent earned between ₦60001 and ₦110000, 7% earned between ₦110001 and ₦160000, while 4% earned above ₦160000 per month. Chi-square analysis of the socio-economic characteristics of the respondents and income generation at α level of 0.05 indicated that ethnicity (0.001) and years of experience (0.009) significantly influenced income while the level of education (0.101), age (0.122), and religion (0.745) had no significant influence on the incomes of marketers. Experience is an important factor in sawn wood marketing and a major determinant of the contribution of timber marketing to the income of timber marketers in Bodija sawn wood Market.

Ming-style round-backed armchairs as a classic Chinese chair design are renowned for the blend of ergonomics, practicality, and elegance. Although the Chinese armchair furniture industry has made strides in sustainability, there is still a need for further improvements in material selection, manufacturing processes, and supply chain management to fully support the development of sustainable furniture. Laminated bamboo lumber as new sustainable materials are becoming a popular option for furniture designers in the era of "sustainable design". This research aims to investigate the feasibility and application of laminated bamboo lumber in the design of Chinese armchair furniture and proposes innovative ideas for optimizing the armchair's design. First, an empirical study was conducted to comprehensively understand the classification of Ming-style round-backed armchairs’ structure to develop a 3D model. Secondly, an experimental research method was then employed to explore the parameters of laminated bamboo lumber for future studies. Additionally, a validation experiment was conducted to compare real-world scenarios with simulations using finite element analysis in Ansys. Finally, finite element analysis was used to test the feasibility and application of laminated bamboo lumber in furniture design, focusing on the material’s mechanical properties. Results indicated that laminated bamboo lumber has excellent mechanical properties as furniture design materials, subsequently, using the optimized results, the use of 0.6319 kg of steel was successfully reduced by 23.68% to ensure the armchair’s stability. This provides a reference for the future compter-assist and standardized innovative design of Chinese armchair. By incorporating compter-assist design and lightweight optimization, it is possible to save materials and make more efficient use of resources, thereby contributing to sustainable development goals in the field of furniture design.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

Purpose. This paper aims to present a unique perspective that emphasizes the intricate interplay between energy, dietary proteins, and amino acid composition, underscoring their mutual dependence for health-related considerations. Energy and protein synthesis are fundamental to biological processes, crucial for the sustenance of life and growth of organisms. Methods and Results. We explore the intricate relationship between energy metabolism, protein synthesis, regulatory mechanisms, protein sources, amino acid availability, and autophagy, in order to elucidate how these elements collectively maintain cellular homeostasis. We underscore the vital role this dynamic interplay has in preserving cell life. Conclusion. A deeper understanding of the link between energy and protein synthesis is essential to comprehend fundamental cellular processes. This insight could have wide-ranging impact in several medical fields, such as nutrition, metabolism, and disease management.

Cross-laminated timber (CLT) possesses both good shape stability and the possible two-way force transfer ability due to its crosswise lamination. However, the transverse layers in CLT are prone to rolling shear failure under an out-of-plane load. An innovative multi-layer composite laminated panel (CLP) was developed by combining structural composite lumber (SCL) and dimension lumber to overcome the rolling shear failure while maintaining high mechanical performance and aesthetic appearance of natural wood. The mechanical properties of 5-layer CLP consisted of laminated strand lumber (LSL) and dimension lumber with different layups were evaluated by both static and modal tests. The results showed that the shear resistance, bending stiffness and moment resistance of CLP were up to 143%, 43% and 87% higher than their counterparts of regular CLT, respectively. The failure modes observed in both shear and bending tests indicated that the use of LSL in transverse layers could eliminate the potential rolling shear failure in CLT. With the lamination properties from components tests as inputs, the validity of shear analogy method was assessed by test results. The mechanical properties can be well predicted by shear analogy method except for the bending moment resistance of CLP and CLT with either rolling failure in the cross layer or tension failure in the bottom layer.

Exosomes are produced by all cell types, their biogenesis is of endosomal origin, originating as a result of cell membrane invagination. Furthermore, physiochemical characteristics are important prerequisites for their commercial application. The representative size range of exosomes is 50-200 nm. Whereas, comparative to animal cell, exosomes from plant cell sources have a relatively larger size range, moreover, exhibit broader therapeutic potential. In this review study, we have briefly discussed the research potential of plant-derived exosomes. Including their earlier studies on biogenesis, characterization, isolation methods, and possible therapeutic applications. Additionally, we have quoted targeted drug delivery for targeted therapies and have provided insights of methods for customizing exosomes produced from plants with various drugs. Most-importantly, here we have embodied exosomes from plant sources are natural nano-inducers possessing the ability for inter-kingdom communication, resulting in cross-kingdom regulations.

Globally, over the past several months millions of persons contracted the coronavirus disease 2019 (COVID-19) resulting in significant mortality. Health care systems are negatively impacted including the care of individuals with cancers and other chronic diseases such as chronic active hepatitis, cirrhosis and hepatocellular carcinoma. There are various probable pathogenic mechanisms that have been presented to account for liver injury in COVID-19 patients such as hepatotoxicity cause by therapeutic drugs, severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection of the bile duct cells and hepatocytes, hypoxia and systemic inflammatory response. Liver biochemistry tests such as AST, ALT, GGT and ALP are deranged in COVID-19 patients with liver injury. Hepatocellular damage results in the elevation of serum AST and ALT levels in early onset disease while a cholestatic pattern that develops as the disease progress causes higher levels of ALP, GGT, direct and total bilirubin. These liver biochemistry tests are prognostic markers of disease severity and should be carefully monitored in COVID-19 patients. We conducted a systematic review of abnormal liver biochemistry tests in COVID-19 and the possible pathogenesis involved. Significant findings regarding the severity, hepatocellular pattern, incidence and related clinical outcomes in COVID-19 patients are highlighted.

A block-diagonal fuzzy neural network for short-term load forecasting is proposed. DBD-FELF consists of fuzzy rules with consequent parts that are neural networks with internal recurrence. These networks have a hidden layer which consists of pairs of neurons with feedback connections between them. The overall fuzzy model partitions the input space in partially overlapping fuzzy regions, where the recurrent neural networks of the respective rules operate. The partition of the input space and determination of the fuzzy rule base is performed by use of Fuzzy C-Means clustering algorithm and the RENNCOM constrained optimization method is applied for consequent parameter tuning. The electric load time-series of the Greek power system is examined, and hourly-based forecasting for the whole year is performed. The performance of DBD-FELF is tested via extensive experimental analysis and the results are promising, since an average percentage error of 1.18% is attained, along with an average yearly absolute error of 76.2 MW. Moreover, DBD-FELF is compared with Deep Learning, fuzzy and neurofuzzy rivals, such that its particular attributes are highlighted.

The advancement of mechanization in forestry has increased productivity in the forestry sector, bringing positive and negative impacts that require a deeper understanding for sustainable forest management. This study aimed to apply a simplified instrument for assessing damage and environmental impacts in forest harvesting of commercial eucalyptus plantations, using a combination of methodologies. The methodology used combined interaction networks and impact assessment matrices, carrying out field surveys, transposing them to interaction networks and weighting them through assessment matrices, resulting in environmental indices (ES) for prioritizing actions. The study was conducted on a commercial eucalyptus plantation in the municipality of São Pedro, São Paulo, Brazil. The mechanized harvesting of the area consists of the structure of a module with a mobile unit consisting of a harvester and forwarder. The results indicated that wood transport presented the highest ES, both positive and negative. The most significant negative impacts (ES) were the depletion of water resources and erosion, while the positive impacts included regional development and job creation. The most notable changes, positive and negative, were observed in the physical and anthropic environment, with a lesser impact on the biotic environment.

In this study, an experiment was conducted on hoop pine (Araucaria cunninghamii), which is a common tree species in Taiwan. Holes with diameters of 4, 5, 7, 10, 12, and 14 cm were drilled in dry hoop pine timber with a diameter of 39 cm and a height of 57 cm, and an 800 MHz Ground Penetrating Radar (GPR) antenna were used to determine the minimum image resolution and the size of the holes in the wood. GPR images of the timber were subjected to a filtering process to obtain characteristic reflection curves of the damage to the timber. Curves with clear waveforms were observed in the GPR profiles of eccentric holes with a diameter of 4 cm. Profiles of the damage were obtained and profile images with the trunk radius at the centre were transformed into polar coordinate images. From these polar coordinate images, the location, size and diameter of the eccentric holes in the wood were identified, and the reflection curves were characterised by waveforms and irregular fluctuations. The risk levels of tree trunks were determined on the basis of their t/R (minimum normal wall thickness of the cross-section of the trunk/radius of the trunk) values and hole area ratios. A comparison between the GPR-based results and the actual diameters of the holes revealed that the filtered GPR profiles could be used for the efficient and accurate assessment of damage to hoop pine timber (average error rate ≤ 4%).

In this paper, we study the well-posedness and asymptotic behaviour of solutions to a laminated beam in thermoelasticity of type III. We first give the well-posedness of the system by using the semigroup method. Then, we show that the system is exponentially stable under the assumption of equal wave speeds. Furthermore, it is proved that the system is lack of exponential stability for case of nonequal wave speeds. In this regard, a polynomial stability result is proved.

In previous work (Z. Angew. Math. Phys. 68(2), 2017), Apalara considered a one dimensional thermoelastic laminated beam under Cattaneo’s law of heat conduction and proved the exponential and polynomial decay results depend on the stability number χ_T . In this paper, we continue to study the same system and show that the solution of the concerned system lacks of exponential decay result in the case χ_T ≠ 0 which solves the open problem proposed by Apalara (Z. Angew. Math. Phys. 68(2), 2017).

Background: The practice of self-medication is common worldwide and is an important component of medical self-care. However, the practice can be dangerous and is linked to various risks for the patients and the entire community. This study aimed to estimate the prevalence and factors associated with self-medication among Bangladeshi adults. Methods: A cross-sectional survey was conducted between April and June 2021 among Bangladeshi adults (aged &gt;19 years) using convenient sampling. A total of 1320 data were collected through face-to-face interviews using a standardized questionnaire. Multivariable logistic regression analysis was used to identify factors associated with self-medication practice (SMP). Results: Overall, 41% of adults in our survey reported SMP. The most common illnesses that prompted SMP were common cold/flu (66.4%), gastric problems (65%), and headache (64.4%). The most frequent reasons for SMP were to get better services (30.59%), perceive SMP without side effects (23.28%), and save time with effectiveness (14.56%). Potential risk factors included 10 years (AOR = 1.91; 95% CI: 1.04 - 3.50) and &gt;12 years of schooling (AOR = 5.03; 95% CI: 2.27 - 11.15), being a businessman (AOR = 4.64; 95% CI: 1.74 - 12.37), having ≤6 family members (AOR = 2.13; 95% CI: 1.40 - 3.24), being a member of a social group (AOR = 1.53; 95% CI: 1.10 - 2.12), a health status check after every six months (AOR = 1.52; 95% CI: 1.08 - 2.13), and current ill-health (AOR = 1.41; 95% CI: 1.06 - 1.87). Protective factors identified included ≤30 years of age (AOR = 0.40; 95% CI: 0.17 - 0.93), and practice of modern (AOR = 0.39; 95% CI: 0.22- 0.69) and herbal (AOR = 0.45; 95% CI: 0.21- 0.97) healing types. Conclusion: More than one-third of the study participants reported practicing self-medication. Increasing the community’s awareness of the extreme consequences of SMP and not just the average experience might sway individuals away from SMP, and implementing strict jurisdiction could be a way to minimize the SMP.

We propose an innovative approach called SMPTC3, designed specifically to enhance security and privacy in cross-chain transaction verification. This approach addresses multi-chain, multi-participant information exchange and large-scale cross-chain transfers, resisting various types of malicious attacks. We leverage the verifiability of cross-chain transactions based on smart contracts and innovatively transform transaction information into confidential sets, organizing them into quadratic secret polynomials. By utilizing secret sharing and random distribution techniques, we construct a secure multiparty computation method, tailored for cross-chain transactions. To enhance the efficiency of cross-chain transactions, we introduce cross-chain batch processing technology, grouping inter-chain transactions into cross-chain transaction sets. Unlike traditional distributed notary technologies, SMPTC3 designates honest participants as a cross-chain notary group, reducing the time required for redundant signature confirmations and significantly lowering the possibility of malicious notaries. Theoretical analysis and empirical experiments demonstrate that SMPTC3 is highly efficient in addressing cross-chain transaction security issues.

Pd EnCat™ 30 is a palladium catalyst broadly used in several hydrogenation and cross-coupling reactions. It is known for its numerous beneficial features, which include high-yielding performance, easy recovery, and reusability. However, the available data regarding its recyclability in Suzuki coupling reactions are limited to a few reaction cycles and, therefore, fail to explore its full potential. Our work focuses on investigating the extent of Pd EnCat™ 30 reusability in Suzuki cross-coupling reactions by measuring its performance according to isolated yields of product. Our findings demonstrate that Pd EnCat™ 30 can be reused over a minimum of 30 reaction cycles, which is advantageous in terms of cost reduction and more sustainable chemical production.

：Non-Euclidean data, such as social networks, and citation relationships between documents, has node information and structural information. Graph Convolutional Network(GCN) can automatically learn node features and association information between nodes. The core ideology of the graph convolutional network is to aggregate node information by using edge information, thereby generating a new node feature. In the process of updating node features, there are two core influencing factors. One is the number of neighboring nodes of the central node, the other is the contribution of the neighboring nodes to the central node. Due to the previous GCN methods not simultaneously considering the numbers and different contributions of neighboring nodes to the central node, we design the Adaptive Attention Mechanism(AAM). To further enhance the representational capability of the model, we utilize Multi-Head Graph Convolution(MHGC). Finally, we adopt cross-entropy(CE) loss function to describe the difference between the predicted results of node categories and the ground truth (GT). Combined with backpropagation, this ultimately achieves accurate node classification. Based on AAM, MHGC and CE, we contrive the novel Graph Adaptive Attention Network (GAAN). Experiments show that the classification accuracy has achieved outstanding performances on Cora, Citeseer and Pubmed datasets.

Multimodal emotion classification (MEC) involves analyzing and identifying human emotions by integrating data from multiple sources, such as audio, video, and text. This approach leverages the complementary strengths of each modality to enhance the accuracy and robustness of emotion recognition systems. However, one significant challenge is effectively integrating these diverse data sources, each with unique characteristics and levels of noise. Additionally, the scarcity of large, annotated multimodal datasets in Bangla limits the training and evaluation of models. In this work, we unveiled a pioneering multimodal Bangla dataset, MAViT-Bangla (Multimodal Audio Video Text Bangla dataset). This dataset, comprising 1002 samples across audio, video, and text modalities, is a unique resource for emotion recognition studies in the Bangla language. It features emotional categories such as anger, fear, joy, and sadness, providing a comprehensive platform for research. Additionally, we developed a framework for emotion recognition that employs a cross-modal attention mechanism among unimodal features. This mechanism fosters the interaction and fusion of features from different modalities, enhancing the model’s ability to capture nuanced emotional cues. The effectiveness of this approach was demonstrated by achieving an F1-score of 0.64, a significant improvement over unimodal methods.

Amazon tropical forest is actually subject to strong deforestation, generally originated from illegal logging, resulting in ecological, environmental and economic problems. Aiming stop deforestation and timber commercialization of illegal logging of tropical forest, new laws has been introduced in many countries. Here we investigated the utility of DNA fingerprinting of nuclear and cytoplasmatic SNPs to timber tracking the intensive logged and commercialized of the Amazonian Neotropical tree Jacaranda copaia. Samples of 832 individuals from 43 populations from Bolivia, Brazil, French Guiana, and Peru were used to investigate the power of 113 nuclear SNPs, 11 CpSNPs, and four MtSNP loci to determine the country and population origin. The genetic differentiation among all populations and contries was high (0.233–0.942), specialy for CpMtSNP (generally>0.6) loci, and there is a strong isolation by distance pathern among populations, favoring the group or individual samples tracking to correct site. For self-assignment tests, we were able to 100% correct determine country and population origin of all samples using all SNPs. Our results show that the use of 128 SNP markers is suitable to correct determination of country and population site of J. copaia timber origin and very useful tool for customs and local and international policies.

Current VAT rules for cross-border e-commerce companies in the EU are not sustainable, because they are extremely complex and often opaque, due to the lack of tax harmonization. The aim of the research is to explore, using a qualitative method, what kind of harmonization would make the current legislation more uniform, simpler, more transparent, and easier to understand, without conflicting with the rules of any Member State. To this end, the aspects of the new platform regulation introduced on 1 July 2021 and its potential for expansion are assessed through information from possible sales models. The research suggests that the rules on platforms do not cover all possible sales models, which in our view imposes an unnecessary extra administrative burden on some businesses and makes their tax activities less transparent. In the light of the results of the research, we propose that the current EU platform regulation should be extended to cover B2B, B2C transactions and services. As a result of this suggested harmonization, a simpler, more transparent, uniform and sustainable tax system would contribute to the whitening of the economy, generating additional tax revenue for Member States.

Safe water is a global public health concern amid increasing scarcity and pollution. Bottled water production and consumption contribute to these problems. This study examines tap water consumption in Italy, assessing associated sociodemographic factors and related health outcomes such as obesity and self-perceived health status. Data from the Italian National Statistics Institute's "Aspects of daily life" survey (N=45,597) were analyzed. Covariates included education, age, gender, economic status, region, concerns about waste and climate change, consumption of carbonated drinks excluding water, alcohol consumption, consumption of vegetables, consumption of snacks, body mass index, and self-perceived health status. Bivariate analyses and mixed-effect logistic regression models explored the associations. People who drink tap water were 19,674 with a higher prevalence in people aged 45 to 59 old, people with a graduate/post-graduate degree diploma, with optimal economic resources, and concerned about waste production and climate change, coming from the North-East regions of Italy. Underweight people showed a higher prevalence of TW assumption as well as those who drink less than occasionally carbonated drinks, drink alcohol, consume vegetables more than once a day, and snacks less than once a week with a satisfying level perceived health status. Regressions showed that all age classes are less likely to drink tap water than people younger than 20 years old. The category with “inadequate” economic resources is more likely to consume tap water. Low educational classes show a low likelihood of consuming tap water as well as Islands. A concern about waste production and climate change is associated with an increased likelihood of assuming tap water. Tap water consumption was negatively associate with obesity but not with a satisfactory Self-perceived health status. Insights from this study can inform public health strategies.

In this paper, we investigate the stabilization of a one-dimensional thermoelastic laminated beam with structural damping, coupled to a heat equation modeling an expectedly dissipative effect through heat conduction governed by Gurtin-Pipkin thermal law. Under some assumptions on the relaxation function g, we establish the well-posedness for the problem. Furthermore, we prove the exponential stability and lack of exponential stability for the problem. To achieve our goals, we make use of the semigroup method, the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem.

The automotive industry is increasingly adopting laminated glass in side and rear windows to comply with safety standards aimed at reducing ejection injuries. However, this trend may have unintended consequences for occupant rescue and escape in submerged vehicle incidents. As more vehicles incorporate laminated glass, concerns arise that they could become "glass coffins" in water, making it more difficult for occupants to exit or be rescued. The use of laminated glass is driven by Federal Motor Vehicle Safety Standard 226 (FMVSS 226) for ejection mitigation, but it does not address the risk of vehicle submersion and occupant drowning. Drowning accounts for a substantial portion of vehicle-related fatalities. As the adoption of laminated glass grows, there is a need for drowning prevention measures, such as automatic window opening systems, to mitigate the risk of vehicles becoming "glass coffins" in water. A comprehensive approach addressing both ejection and submersion dangers is necessary to maximize occupant protection and save lives.

In order to understand the hot deformation behavior of novel Cu/Al laminated composites, isothermal hot compression tests were conducted by Gleeble-1500D thermo-mechanical simulator. And the effect of bonding interface, deformation temperature and strain rate on the deformation behavior was analyzed. Results show that under the interface constraint effect, soft Al layer trends to flow synchronously with hard Cu layer. And further microstructure examinations indicate the cooperative deformation capability of Cu/Al composites increases with increasing stain rate and decreasing deformation temperature. Strain hardening exponent, calculated based on the true stress-true strain data, also proves the effect of deformation temperature and strain rate on the cooperative deformation behavior. Meanwhile, unique composites structure allows the Al matrix to exhibit the characteristic of dynamic recrystallization during the hot deformation process. Lastly, strain compensated Arrhenius-type constitutive equation was employed to describe the coupling effect of temperature, strain rate and strain on the flow stress.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

Background: Studies have tried to identify predictors of functional markers of keratoconus progression, whereas structural outcomes of collagen cross-linking have not been properly investigated. Objective: find and set up a combination of diagnostic modalities and measurements to reliably reflect CXL efficiency. Material and methods: We retrospectively reviewed the medical histories of 107 KC patients (131 eyes) who underwent CXL in a medical center from January 2018 to December 2022. The dataset included preoperative examinations and follow-up results, which provided a total of 796 observations. The cases of other corneal diseases, repeated CXL, pregnancy, and observations without follow-up examinations were excluded. Results: The study findings revealed a significant drop in the central and corneal thickness during 14.01±9.98 months of observations. Linear and polynomial equations suggested different trends in pachymetry change after CXL. The linear model showed corneal thinning, and according to the polynomials, pachymetry findings return to baseline values two years after CXL. Conclusion: The most reliable prognosis of postoperative corneal thickness is achieved with the models trained on keratometry readings and topography indices. BAD indices are also reliable predictors of the corneal thickness after CXL. A combination of the aforementioned structural parameters and their derivatives can reliably predict CXL efficiency.

Myocardial Infarction with Non-Obstructive Coronary Arteries (MINOCA) is a clinical entity characterized by the absence of significant coronary artery obstruction in epicardial arteries (&lt; 50%) on coronary angiography in the setting of acute myocardial infarction (AMI). This article aims to provide a narrative review of the pathophysiological mechanisms, diagnostic challenges, and prognosis associated with MINOCA focusing only on cases associated with myocardial ischemia but of non-atherosclerotic origin. Etiological factors, including thromboembolism, coronary artery spasm, spontaneous coronary artery dissection, coronary microvascular disease, and supply-demand mismatch are addressed. Imaging modalities such as echocardiography, advances in coronary angiography like intravascular ultrasound (IVUS) and optical coherence tomography (OCT), cardiac magnetic resonance (CMR), and coronary computed tomography angiography (CCTA) are also analyzed. MINOCA patients have a better short-term prognosis compared to those with obstructive coronary artery disease but face significant long-term risks, underscoring the need for precise diagnosis and management strategies. Elevated inflammatory markers and specific genetic predispositions are also associated with adverse outcomes in MINOCA. This review focused on MINOCA from the pathophysiological perspective on ischemic, non-atherosclerotic causes, the diverse underlying mechanisms, the challenges in achieving accurate diagnosis, the importance of a tailored therapeutic approach and the necessity for further investigation of clinical outcomes.

Background: Ultraviolet (UV) radiation from the sunlight can harm skin cells, causing short-term effects, such as sunburns and long-term effects, such as pigmentation changes, changes in the skin's immune responses, and increased risk of skin cancer. These conditions can be largely prevented with proper sun protection measures and behavioural changes. This study aims to assess the knowledge on sun protection behaviour and baseline knowledge of medical students from the “Carol Davila” University of Medicine and Pharmacy, Bucharest, Romania. Methods: Data in this cross-sectional study were collected through a Google Forms questionnaire, which was distributed from November 2023 to December 2023 via digital communication channels to students across all academic years. STROBE guidelines were consulted for data synthesis; Results: A total of 668 stu-dents responded. The student cohort demonstrated a commendable level of awareness of the risks associated with sun exposure and the advantages of employing sun protection factor (SPF); how-ever, the incidence of sunburns remained notably elevated (72.3%). Further analysis revealed cor-relations among gender, academic year, presence of photosensitizing conditions, and adherence to SPF application. Additionally, there is a need to improve understanding of the appropriate appli-cation techniques for SPF, as only 11.5% of the students exhibited proficiency in this regard; Con-clusions: As future healthcare providers, medical students hold significance in promoting healthy behaviours in the broader community. This study indicates that while their knowledge about sun protection is satisfactory, there is scope for enhancement.

Objectives: Evaluate the performance of diagnostic measures (sensitivity and specificity) of the intrinsic capacity (IC) construct recommended by the WHO ICOPE guidelines by domain and by age group. Study design: This cross-sectional study included 164 community-dwelling elderly (95 women and 69 men). The participants completed the assessment of the 5 domains of IC (cognition, psychological, vitality, locomotion and sensory). In addition, they were assessed for activities of daily living (ADL), instrumental activities of daily living (IADL), frailty and urinary incontinence. Main outcomes measures: Descriptive statistics were used to summarize the intrinsic capacity and identify which domains were compromised. Comparisons between three or more samples were made by 1-way ANOVA with Bonferroni post-test and those with two samples by the t-test or Mann-Whitney test for quantitative variables. Chi-square test was used for qualitative variables. The sensitivity and specificity of each domain and each domain by age group were evaluated using the ROC curve. Results: Participants with a decline in IC were older, worse ADL, IADL and mental function, low gait speed, and higher depression scores. In addition, people with a decline in IC had frailty, urinary incontinence. Other issues related to the decline in CI were self-reported non-practice of physical activities and level of schooling.The evaluation of each domain did not prove to be a good screening tool (sensitivity or specificity &lt; 80%, but both values &gt; 50%). When the analyses were separated by domain and age group, good performance was found in the psychological (69-69 years and ≥80 years), vitality (≥80 years) and sensory (≥80 years) domains. Conclusions: The ICOPE screening tool performed well in terms of diagnostic measures when applied by domain and age group.

Chronic stress, culminating in burnout, evolves gradually and is notoriously difficult to detect due to vague symptoms and individuals' hesitance to acknowledge their struggles. To expedite the identification and recognition of this condition, enabling timely psychological intervention, the integration of Artificial Intelligence (AI) is increasingly considered. This research does not assert the feasibility of an AI system managing all aspects of chronic stress's impact. However, it highlights the capability of current technology to detect stress indicators based on quantifiable data like Heart Rate (HR) and organizational climate dimensions. Although other physiological markers such as oximetry, skin galvanic response, and EKG have been explored, they have not shown reliable differentiation between stress and joy. Focused on the unique context of school principals in the Bedouin regions of Israel, this study investigates the interplay between HR, organizational climate, and stress levels. It introduces a novel application of a fuzzy logic tool that combines HR and organizational climate metrics to aid in stress diagnosis. This tool incorporates the psychologist's expertise to provide real-time data crucial for developing effective coping strategies. While the AI-supported fuzzy system does not replace professional psychological intervention, it significantly enhances the speed of condition identification and intervention planning, thus shortening the response time to stress-related issues in educational leadership within culturally specific settings. The application of such AI-driven tools is pivotal for sustaining the well-being and effectiveness of educational leaders, thereby supporting the broader goal of educational sustainability.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

Cross-linked polyethylene (XLPE) is a highly all-important material renowned for its exceptional physical and chemical properties, and it is extensively utilized in various industries such as con-struction, piping, cable insulation and medical equipment. The cross-linking process of polyethylene involves chemical or physical bonding of polymer chains to enhance its resistance to heat, chemicals and mechanical stress. This study offers a comprehensive overview of recent research and potential advancements in this field, with a particular focus on the development of efficient techniques and environmentally sustainable cross-linking systems. It evaluates the opportunities and challenges faced by cross-linked polyethylene materials across diverse applications, providing valuable insights for future research in this area.

Domain generalization has led to remarkable achievements in Hyperspectral Image (HSI) classification. Inspired by contrastive language-image pre-training (CLIP), the language-aware domain generalization method has been explored to learn cross-domain-invariant representation. However, existing methods face some challenges: 1) The weak capacity to extract long-range contextual information and inter-class correlation. 2) Due to the inadequacies of the large-scale pre-training for HSI data, the spatial-spectral features of HSI and linguistic features can not be straightforwardly alignment. To address the above problems, a novel network has been proposed with a CLIP framework, which consists of an image encoder, based on an encoder-only transformer to obtain the global contextual information and inter-class correlation, a frozen text encoder, and a cross-attention mechanism, named Linguistic-Interact-with-Visual Engager (LIVE), enhances the interaction between two modalities. Extensive experiments demonstrating superior performance over state-of-the-art methods in HSI Domain Generalization with a CLIP framework.

The uptake of buildings employing cross-laminated timber (CLT) assemblies and designed to Passivhaus standard has accelerated internationally over the past two decades due to several factors including design responses to the climate crisis by decarbonising the building stock. Structural CLT technology and the voluntary Passivhaus certification both show measurable benefits in reducing energy consumption, while contributing to durability and indoor comfort. However, there is a general lack of evidence to support a fast uptake of these technologies in Australia. This paper responds to the compelling need of providing quantitative data and adoption strategies, it explores their combined application as a potential pathway for climate-appropriate design of energy-efficient and durable mass timber envelope solutions for subtropical and tropical Australian climates. Hygrothermal risk assessments of interstitial condensation and mould growth of CLT wall assemblies inform best-practice design of mass timber buildings in hot and humid climates. This research found that the durability of mass timber buildings located in hot and humid climates may benefit from implementing the Passivhaus standard to manage interior conditions. The findings also suggested that climate-specific design of the wall assembly is critical for mass timber buildings, in conjunction with excellent stormwater management practices during construction and corrosion protection for metallic fasteners.

Non-timber forest Products (NTFPs) are a broad category of natural resources harvested from forests that do not involve cutting down trees for their wood or timber. NTFPs play a vital role in the livelihoods and economies of many rural communities, particularly in forest-dependent regions. Despite the benefits obtained from NTFPS, little is known about its potential to alleviate poverty in the local communities. The objective of this review is to comprehensively assess the potential of NTFP's contribution to poverty reduction within forest fringe communities. The study employed the systematic review method to delve into the multifaceted relationship between NTFPs and poverty alleviation. We followed the preferred reporting items for systematic reviews and meta-analyses protocol (PRISM-P). In all, 58 research articles were reviewed. The results indicated that NTFPs hold significant promise as a tool for poverty alleviation. Globally, NTFPs have the potential to alleviate poverty and increase household incomes between 19% and 78% within forest fringe rural communities. In addition, the review indicated that countries in Africa and Asia depend highly on NTFPs and provide substantial amounts of income to the locals. However, the potential for NTFPs to reduce poverty is not uniform. It is highly contingent upon local ecological conditions, market accessibility, community involvement, and supporting policies and interventions. In conclusion, this systematic review demonstrates that NTFPs have a substantial role in poverty alleviation. This study underscores the need for continued research and targeted development initiatives to unlock the vast potential of NTFPs in addressing poverty challenges.

Forests are a large reservoir of biodiversity on which riparian populations frequently rely. Non-timber forest products (NTFPs) are an important source of income for millions of people living in forest-adjacent communities. This study aims at characterizing the types and uses of NTFPs in order to determine whether their exploitation in the eastern Democratic Republic of the Congo is sustainable. Interviews and direct observation were carried out with NTFP stakeholders (harvesters, sellers, and consumers) in Kalonge, near the Kahuzi-Biega National Park. The results showed that 40 NTFPs of plant origin and 10 NTFPs of animal origin are commonly exploited and used in food and traditional medicine. The most common NTFP harvesting techniques are debarking, picking, digging up, felling, and wine extraction, which are all tailored to the plant part. A significant relationship (p-value&lt; 0.001) has been established between the types of NTFPs used and harvesting methods as well as between the types of NTFPs used and organs retrieved. NTFP products are mainly obtained from the natural forest KBNP but also in the woodland, trees grown outside of forest or through domestication. Their abundance, however, is hampered by the extraction of wood for charcoal, energy, and timber, as well as agricultural expansion. The supply of NTFPs is determined by the market demand for the products, the nature of the product, and the ease of disposal. The NTFPs value chain in Kalonge is important to the local economy, however exploitation of NTFP products remains uncontrolled and should be well managed to ensure sustainability.

Wood-borer extermination by a dry heat clean-up is the essential method from the point of view of sustainability of historical wooden structures like trusses and ceilings in heritage-listed buildings. The wooden components are heated by a hot air of temperature about 100°C until the temperature in the centre of the wooden structures reaches 55°C to kill the wood-borers. In this article we review the method and present solution of the heat equation for structural wooden components. We also suggest an approximate formula that enables to estimate the necessary heating time for different cross sections of wooden components and can be used in technical application of the method.

The comfort of the elderly in hospital settings requires a special attention from the involved health care professionals, particularly nurses, since hospitalization often generates suffering and discomfort. In such contexts, it is essential to take into account the specific characteristics of the elderly, considering their life experiences and their needs, to promote the health, well-being, and comfort of this population. Hence, the present work aimed to explore the nursing interventions that promote comfort among the elderly in hospital settings. A mixed descriptive exploratory study was conducted, through the application of a questionnaire, using intentional non-probabilistic sampling. The study encompassed 55 elderly individuals hospitalized in a medical service of a public hospital located in Lisbon. The results show that the participants perceived a reasonable level of comfort (5.65 ± 6.46). The following categories emerged from the content analysis: 1) Physical interventions; 2) Psycho-spiritual interventions; 3) Socio-cultural interventions; and 4) Environmental interventions. These findings help to understand comfort-promoting nursing interventions in the studied population. It was concluded that, to improve care quality, comforting interventions should focus on the elderly patient’s individuality, through support activities, empowerment, and the preservation/correction of the surrounding environment. Additionally, the provided care should be based on the real needs, expectations, preferences, and values of the elderly individual.

This research presents the Cross-Cultural Intelligent Language Learning System (CILS), a novel approach integrating Artificial Intelligence (AI) into language education to enhance cross-cultural communication. CILS utilizes advanced AI technologies to provide adaptive, personalized learning experiences that cater to the unique linguistic and cultural backgrounds of each learner. By dynamically adjusting content and methodology, CILS significantly improves linguistic proficiency and cultural understanding, essential for effective global interactions. The implementation of CILS in platforms such as Busuu and HelloTalk has demonstrated marked improvements in engagement and communication skills among learners. Empirical studies validate the system's effectiveness in real-world settings, showing enhanced learner performance and increased intercultural competence. Additionally, the Technology Acceptance Model (TAM) applied confirms that the usability and perceived usefulness of AI-driven systems strongly influence learner acceptance and sustained use. This study not only underscores the potential of AI in transforming language education but also highlights the critical role of cultural sensitivity in designing educational technologies.

In this study, cotton fabric reinforced phenolic resin (CPF) composites were modified by adding four two-dimensional fillers: graphitic carbon nitride (g-C3N4), graphite (Gr), molybdenum disulfide (MoS2), and hexagonal boron nitride (h-BN). The tribological properties of these modified materials were investigated under dry friction and water lubrication conditions. CPF/ Gr composite exhibits significantly better tribological performance than the other three fillers modified CPF composites under dry friction, with a 24% reduction in friction coefficient and a 78% reduction in wear rate compared to unmodified CPF composite. Under water lubrication conditions, all four fillers did not significantly alter the friction coefficient of the CPF composite. However, except for an excessive amount of Gr, the other three fillers can reduce the wear rate. Particularly, in the case of 10% MoS2 content, the wear rate decreased by 56%. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were employed for the analysis of the morphology and composition of the transfer films. Additionally, molecular dynamics (MD) simulations were conducted to investigate the adsorption effects of Gr, MoS2, and PF on the counterpart surface under both dry friction and water lubrication conditions. The difference in the adsorption capacity of Gr and MoS2 on the counterpart, as well as the resulting formation of transfer films, accounts for the variation in tribological behavior between CPF/Gr and CPF/MoS2 composites. By combining the lubrication properties of MoS2 and Gr under dry friction and water lubrication conditions, using them as co-fillers can achieve a synergistic lubrication effect.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

Understanding the dynamics of teamwork and communication among healthcare professionals is crucial in the face of evolving healthcare challenges. This study assessed relational coordination among healthcare professionals in the South Tyrolean healthcare system in Italy, focusing on communication and teamwork dynamics in a cross-sectional survey. Using the validated Relational Coordination Survey (RCS) instrument and 525 completed online responses, the questionnaire aimed to understand the implications of different levels of relational coordination ratings by general practitioners, hospital physicians, nurses, and administrative personnel (response rate 26%). The demographics of the participants revealed a predominance of female professionals (64%), with an average age of 50 and 18 years of service. The resulting RCS scores varied significantly across professional groups, with nurses reporting the highest within-group scores, indicating moderate coordination, and administrators reporting the lowest scores, reflecting areas of weak coordination. Between-group relational coordination was generally perceived as weak across professional groups, with the least weakness observed between general practitioners and nurses. German or Italian language and health district affiliation emerged as significant factors influencing relational coordination ratings, highlighting the need for differentiated understanding and strategies in multilingual and diverse regional settings. Assessments of interdisciplinary feedback and referral practices highlight the variation in teamwork and communication weaknesses and underscore the need for targeted interventions to improve relational coordination. This study provides insights into the complexity of relational dynamics in health care settings. It suggests that improving relational coordination through tailored strategies could significantly improve team effectiveness, quality of patient care, and overall system efficiency.

This paper is the continuation of a previous study, which highlighted some inconsistencies in the RILEM guidelines for the interpretation of the diagonal compression test. Although improved compared to the ASTM guidelines, in fact, the RILEM guidelines underestimate the state of hydrostatic stress induced by the diagonal compression test at the center of the wallette. The new interpretation of the diagonal compression test proposed in this article shows that the RILEM guidelines actually underestimate both the hydrostatic and the deviatoric stress states at the center of the wallette. The new formulation complies with the linear elastic theory and allows us to use the the diagonal compression test to identify the three elastic coefficients of masonry. In particular, it allows the identification of the Poisson ratio, which instead takes on a conventional value in the RILEM and ASTM guidelines. The difference of one order of magnitude between the conventional and proposed Poisson’s ratio is in agreement with the experimental results on another brittle material, namely concrete. Finally, the new proposal fills the gap between the results provided by the two tests usually performed to identify the shear behavior of masonry: the diagonal compression test and the shear-compression test.

The yield of logging in a forest management area using only the volume variable is not sufficient to assess effective wood productivity. The objective was to evaluate production using different logging variables to point out possible divergences between what was planned and what was actually carried out, in order to indicate adjustments to annual operating plans (AOPs) in the Amazon. The database comes from a community forest management area in the Tapajós National Forest, con-sidering three sources: 100% inventory, AOP planning and the post-exploration report. The pro-duction yield considering the number of trees felled and the effective volume were compared with the AOP planning. The volume estimated by the generic equation was compared with the cubed volume and the commercial height variable was evaluated. Of the 6,267 trees selected, 5,090 trees were harvested (3.2 trees.ha-1), indicating a yield of 85.0% of the estimated volume. Of the 25 commercial species logged, the most representative were: Manilkara huberi, Vochysia maxima, Lec-ythis lurida, Couratari guianensis and Hymenaea courbaril. It can be concluded that the number of trees, cubed volume and commercial height are post-exploration yield response variables and not just volume, as is currently used in SFMPs.

In ancient buildings, timber members could need specific on-site interventions, including reinforcement or repair, sometimes inserting of reinforcing material into grooves routed in the original sound wood. Grooves number, positions and dimensions, and strengthening materials may differ, according to the desired increase of bending stiffness and strength. The Modulus-of-Elasticity (MOE) of each beam is of key importance, but the incisions can affect it, net of the reduction of the removed wood. In this study 12 old beams were accurately measured and their static and dynamic MOEs calculated before and after the grooves processing, to simulate the operations of typical reinforcing interventions. One groove was routed along the length of each beam and deepened progressively by three steps. Tests have showed how the MOE is affected by the groove depth, decreasing up to one third. The paper proves how the weakening effect of grooves on-site can be assessed with dynamic MOE and roughly predicted by means of visual survey. Grooves need for strengthening beams, must be carefully evaluated because of the variation of the actual mechanical properties, net to lost wood.

Electrifying aircraft, a crucial advancement in the aviation industry, aims to cut pollutive emissions and boost energy efficiency. Traditional aircraft depend on fossil fuels, which contribute significantly to greenhouse gas emissions and environmental pollution. Despite progress in electric propulsion and energy storage technologies, challenges such as low energy density and integration issues persist. This paper provides a comprehensive thematic and bibliometric analysis to map the research landscape in aircraft electrification, identifying key research themes, influential contributors, and emerging trends. The study applies natural language processing to unstructured bibliographic data and cross-sectional statistical methods to analyze publications, citations, and keyword distributions across various categories related to aircraft electrification. The findings reveal significant growth in research output, particularly in energy management and multidisciplinary design analysis. Collaborative networks highlight key international partnerships, with the United States and China being key research hubs, while citation metrics highlight the impact of leading researchers and institutions in these countries. This study provides valuable insights for researchers, policymakers, and industry stakeholders, guiding future research directions and collaborations.

In the context of sustainable development, integrating the work aspect into health promotion systems is essential, ensuring that employees maintain a healthy balance between their professional and personal lives, which respects and amplifies the potential of every individual. Lately, there has been a noticeable shift of medical professionals from the public to the private sector. This trend paints a bleak picture, highlighting the vulnerabilities of a system teetering on the brink of failure, with significant impacts on patient care. Among the myriad reasons behind this shift, burnout stands out prominently. Medical professionals face increasing pressures due to understaffing, limited organizational support, and insufficient resources, leading to feelings of cynicism, exhaustion, and detachment from their roles. Utilizing the Maslach et al. questionnaire, we assessed the risk of burnout among physicians in public hospitals to identify and underscore preventive measures and improvements, correlating our findings with key aspects of organizational empowerment. Our research indicates that enhancing interpersonal relationships and resources—both within teams and between the organization and its physicians—is crucial for the revival of the healthcare system. This approach aims at improving the delivery of healthcare services and offering appropriate recognition to healthcare professionals, aligning with the principles of sustainable employment.

Herein, bamboo-laminated lumber for furniture was coated with waterborne acrylic paint. The effects of different painting techniques and quantities on the drying rate, smoothness, hardness, adhesion and wear resistance of the paint film were investigated. Then, the thermal properties of the paint were analysed using thermogravimetry and differential scanning calorimeter to examine the film-forming mechanism. The results showed that painting technique had no effect on the drying time, flatness, hardness and adhesion of the paint film, but it influenced the wear resistance. Herein, the films’ flatness showed little variation with different painting methods (one-layer primer one-layer topcoat, one-layer primer two-layer topcoat, two-layer primer one-layer topcoat and two-layer primer two-layer topcoat). The drying time for primer surfaces/solids was 8min/8.5 min, while it was 6.5/7 min for topcoats. The paint films exhibited grade B hardness and grade 0 adhesion and the better wear resistance when using one-layer primer one-layer topcoat at 51.24 mg·100 r−1. The amount of paint applied significantly affected the drying time and flatness of the paint film. As the quantity increased, the drying time of the paint’s surfaces and solids also increased, whereas the film’s flatness initially increased before decreasing. The film’s optimal adhesion, hardness and wear resistance values were grade 0, grade B and 51.24 mg·100 r−1, respectively, when 80 g/m2 of paint was applied. Thermal analysis of the primer and topcoat showed that water decomposition occurred at 100℃ and thermal decomposition of organic components occurred at 350℃. The primer and topcoat exhibited the same weight loss, but primer’s thermal loss rate was higher than that of topcoat. Consequently, the topcoat displayed better thermal stability than the primer.

The increase in the frequency of droughts in Africa has increased the interest in crops with drought escape mechanisms like grain Amaranth (Amaranthus hypochondriacus). However, the white-seeded grain Amaranth is easily cross-pollinated by its black seeded wild relatives such as smooth pigweed (Amaranthus hybridus). A study to investigate a minimum isolation distance enough to prevent seed contamination study was carried out at three sites namely Gweru and Bindura (2020/2021 rainy season) and Shamva (2021/2022 rainy season). Smooth pigweed was planted at distances of 3 to 150 m from pure grain Amaranth. Close monitoring of phenology and measurement of meteorological conditions such as temperature, wind speed and direction were done during the anthesis period. Cross-pollination in grain Amaranth was influenced by distance from the pollen source. A maximum of 12.9 % contamination rate was measured within the 10 m radius from the pollen donor plot and a minimum outcrossing rate of 0.45 % was recorded at the widest distance of 150 m. It can be concluded that complete removal of wild relatives of grain Amaranth is important within the field at as far as 150 m from the crop.

In recent years there has been a clear increase in bottled water consumption, globally which translates to significant health and environmental concerns. This cross-sectional study aims to understand the attitude and preferences of university students in Qatar towards use of bottled and tap water for drinking purposes using an online survey questionnaire. The number of students who responded to the online survey was 14% of the entire student population within the university (n = 688). Overall, majority of the students reported plastic bottled water as the main source of drinking water they preferred to use on campus (n=468; 68.02%), with a higher proportion of females (72.08%) preferring the use of plastic bottled water. Out of the 468 students who preferred plastic bottled water, safety was the most important factor (43.80%) followed by convenience (16.88%) and taste (15.60%). Cost (15.17%), personal/family habits (5.13%), Environmental concerns (2.14%) and minerals (1.28%) were found to be the least important factors. Among the 45 students who preferred tap water over plastic bottled water, cost (46.67%) was the dominant factor followed by convenience (20.00%) and environmental concerns and safety (13.33% each), taste (4.44%), and personal/family habits (2.22%). This study recommends campaigns to focus on attitude and behavior change and not solely emphasize knowledge; 71.7% believed that plastic water bottles are more harmful to the environment, yet the greater majority still resorted to this source. There is an immediate need to further educate students through environmental and health literacy programs on water consumption and quality. Enabling the population to understand the positive and negative aspects of their choices, may be an effective remedy to ensuring a healthy population and healthy environment.

Despite decades of conflict and political instability, drought has also severely affected Afghanistan’s rural population and agriculture sector. Agriculture is a primary livelihood source in the country, and recurring droughts have put cascading pressures on the agricultural economy and food security. Therefore, understanding the key drivers of all risk components through a comprehensive risk assessment is critical for proactive drought risk management. This study assesses agricultural drought risk from an integrated perspective, emphasizing the combined effects of drought hazard, exposure, and vulnerability. Multi-methods research was conducted, employing remote-sensing-based analysis covering a period from 2001 to 2023. We used the Vegetation Condition Index (VCI) to analyze the drought hazard for the agricultural system during the winter growing season. The vulnerability indicators and exposure levels of the agricultural system were determined through spatial analysis combined with a literature review and expert consultation. An adapted conceptual framework of the Intergovernmental Panel on Climate Change (IPCC) was utilized, which incorporates hazard, exposure, and vulnerability to define risk. The results revealed that droughts occur frequently and in changing patterns throughout the country. All provinces have experienced drought over the past two decades, albeit with varying severities and frequencies. Severe droughts were observed in 2001-2002, 2008, 2011, 2018, and consecutively in 2021-2022-2023. Drought vulnerability and exposure vary widely across the country, particularly in the northern, western, and southern provinces. The final calculated risk shows that most provinces in southern and southwestern zones face a high risk of recurrent droughts, further exacerbating agricultural challenges in these regions. Such analyses under a multimethod approach provide information on spatial patterns of drought risk and drivers of agricultural systems that can support decision-makers and policymakers in formulating strategies to reduce drought risk and adapt to the agricultural sector.

Pregnant women (PW) are at a higher risk of diseases and hospitalization from viral respiratory infections, specially influenza, due to cardiopulmonary and immunological changes. This study assessed the impact of viral respiratory infections on PW hospitalized with severe acute respiratory infection (SARI). It´s a cross-sectional study with 42 PW and 85 non-pregnant women (NPW) admitted with SARI to two tertiary hospital between January 2015 and December 2019. The rate of virus prevalence, SARI hospitalization, length of hospital stay, oxygen supplementation, intensive care unit (ICU) admission, and death were comparable between PW and NPW. Multivariate analysis showed that PW had a higher rate of viral SARI hospitalizations (OR = 2.37; 95% CI =1.02 - 5.48) compared to NPW, with influenza virus being the most prevalent (aOR =7.58; 95% CI =1.53 - 37.66). Length of hospital stay (aOR = 0.83; 95% CI = 0.73 – 0.95) and admission to the ICU (aOR=0.028; 95% CI=0.004 - 0.25) were lower in PW compared to hospitalized NPW. Respiratory viruses had a greater impact on the frequency of SARI in the group of PW. Although PW had a higher rate of influenza SARI, they had a better outcome than NPW due to the treatment they received.

This study examines the association of sociodemographic risk factors and the comorbidities of COVID-19. Most COVID-19-related studies were conducted in inpatient settings among patients with severe infection during the first and second waves of the pandemic. The third wave with less severe Omicron variant presented a unique opportunity to observe the adult patients treated in outpatient settings. We conducted a cross-sectional study (117 patients aged &gt; 40 years presented with symptomatic COVID-19). We employed the Charlson Comorbidity Index (CCI) to compute comorbidity burden, Medical Outcomes Survey Short form (SF-12) to measure general health, and Self-care Self- Efficacy Scale (SCSES) to assess self-care ability. Fisher’s exact test and analysis of variance (ANOVA) were used to compute the relationship between comorbidities and demographics. This study report focuses on the distribution of the comorbidities and its relationship to demographic variables. The top five comorbidities were hypertension (42%), diabetes (31%), pulmonary disease/asthma (19%), depression (14%), and cancer (11%). Depression was significantly higher among younger age groups (p&lt;0.01) and women (p&lt;0.05). Age (p&lt;0.0001) and income (p&lt;0.01) were the most significantly associated demographics with the comorbidity burden. Incidence of pulmonary disease showed a positive association to educational status (p=0.05). This was the first study to report a significant prevalence of depression among adults with symptomatic COVID-19.

The existing segmentation-based scene text detection methods mostly need complicated post-processing, and the post-processing operation is separated from the training process, which greatly reduces the detection performance. The previous method, DBNet successfully simplified post-processing and integrated the post-processing into a segmentation network. However, the training process of the model took a long time for 1200 epochs and the sensitivity to texts of various scales was lacking, leading to some text instances being missed. Considering the above two problems, we design the text detection Network with Binarization of Hyperbolic Tangent(HTBNet). First of all, we propose Binarization of Hyperbolic Tangent (HTB), optimized along with which, the segmentation network can expedite the initial convergent speed by reducing the amount of epochs from 1200 to 600. Because features of different channels in the same scale feature map focus on the information of different regions in the image, to better represent the important features of all objects in the image, we devise the Multi-Scale Channel Attention(MSCA). Meanwhile considering that multi-scale objects in the image cannot be simultaneously detected, we propose a novel module named Fused Module with Channel and Spatial(FMCS), which can fuse the multi-scale feature maps from channel and spatial dimension. Finally we adopt cross entropy as the loss function, which measures the difference between predicted values and ground truths. The experimental results show that HTBNet compared with lightweight models has achieved competitive performance and speed on Total-Text(F-measure:86.0%, FPS:30) and MSRA-TD500 (F-measure:87.5%, FPS:30).

Composite timber-concrete constructions are innovative structural systems which have become the subject of research and practical usage, primarily due to their attractive mechanical properties. This article deals with the experimental procedure and the analysis of the mechanical behavior of two different serious of timber-concrete composite beams. In the composite beams of the A series, screws were used as a fastening system in the interlayer between the timber and concrete parts, whereas in the B type series, a more complex system, the combination of notches and screws, was used for the same purpose. Both series were exposed to loading up to a fracture point by the means of the standard procedure (four point bending test). The mechanical behavior of the A and B-series beams was analyzed by a comparative analysis referring to: the correlation of the fracture loading and the deflection at the moment of fracture, forms and mechanisms of fracture, the development of dilatations at certain points of specific cross-sections, the displacement in the timber-concrete interlayer in the support zones, the value of shear stresses and the calculated values of the effective bending stiffness of the beams. The B-series beams where a more complex fastening system, as it was expected, showed a better mechanical behavior than the A-series beams.

The issue of environmental sustainability is increasingly topical and one of the most impactful sectors is that of the construction industry. As stated in the reports of the GlobalABC, the building sector is the main responsible for GHG emissions, generating about 37% of global CO2e emissions. Already during the phases of production and construction of buildings about 10% of global emissions are produced, while the remaining part comes from their use, from the energy for air conditioning and lighting. Reducing emissions in the pre-use phase of buildings is therefore a crucial issue for combating climate change. The research investigates the potential of timber construction systems, thanks to the carbon storage property of the material. The proposed calculation methodology is structured according to the LCA-Life Cycle Assessment approach, referring to the C2H phase (from Cradle-To-Handover), and evaluates emissions related to the production and construction of buildings. To identify the timber construction system that minimizes CO2e emissions, within the limits of the investigation (A1-A5 phases), the method was applied to two buildings built with different technologies: one with X-Lam panels and one with a framed structure. The results were analyzed, compared, and discussed to demonstrate that the timber buildings are the most virtuous solution in the Net Zero Carbon perspective by 2050.

Efforts to quantify and reduce greenhouse gas (GHG) emissions of the built environment often neglect embodied emissions, instead focusing on reducing emissions from building operations. Utilizing sustainably sourced mass timber offers low embodied carbon alternatives to traditional concrete and steel structural systems, however the variability in embodied carbon for different mass timber approaches remains understudied. In this study, we used life cycle assessment (LCA) to compare the whole building embodied carbon of nine mass timber design options and two typical concrete and steel reference cases for an eight-story mixed-use building, ensuring structural, acoustic, thermal, programmatic, and fire-rating equivalence between the designs. The study found that the mass timber designs vary significantly, ranging between a 14-52% reduction in whole building embodied carbon from the most impactful reference case, and a 31-73% reduction when considering the structural systems alone. This study demonstrates the value that whole building LCA (WBLCA) provides as a primary driver for low-carbon structural system design and architectural development of mass timber buildings, beyond that of single material comparisons using environmental product declarations (EPDs).

Despite the importance of influenza vaccination for healthcare workers (HCWs), their uptake remains challenging. This study aimed to measure influenza vaccine hesitancy among HCWs in Nakhon Phanom province, Thailand. A representative cross-sectional survey was conducted at six hospitals during August – September 2020 using a self-administered questionnaire. HCWs delaying getting influenza vaccines, accepting but unsure, or refusing with doubts were categorized as hesitant. Those accepting without any doubts were classified as non-hesitant. Vaccine hesitancy determinants were identified by multivariable logistic regression analysis. A total of 338 participants (97%) completed the questionnaires; most were female nurses working at district hospitals without pre-existing chronic medical conditions. Nearly 60% of participants (197/338) exhibited influenza vaccine hesitancy, and significant factors included age above 50 years adjusted odds ratio [aOR] 3.2, 95% CI 1.3-8.5), fair knowledge of influenza/vaccination (aOR 0.4, 95% CI 0.2-0.8), and negative influence of other HCW (High level– aOR 2.3, 95% CI 1.1-4.8; Moderate level- aOR 2.1, 95% CI 1.1-4.4). Imparting updated information to the HCW combined with positive guidance from influential peers may help reduce this hesitancy.

Background/Objectives Bowel endometriosis (BE) is defined as the presence of endometrial-like tissue in the muscular layer of the bowel wall. When BE does not cause severe obstruction to fecal transit, not leading to (sub)occlusive symptoms, the decision to operate becomes challenging as intestinal surgery is associated with higher complication rates and long-term bowel dysfunction. The aim of this cross-sectional study is to evaluate the quality of life (QoL) in patients with BE undergoing medical therapy or expectant management, investigating the impact of characteristics of BE nodules on QoL and intestinal function. Methods A retrospective cross-sectional analysis was conducted on 580 patients with BE who did not undergo surgery but were treated conservatively by medical therapy or expectant management between January 2017 and August 2022. The diagnosis of BE was done by transvaginal ultrasound and confirmed at double contrast barium enema. After at least one year of follow-up, QoL and intestinal function of patients were evaluated by the Endometriosis Health Profile-5 (EHP-5) questionnaire and Bowel Endometriosis Symptom score (BENS), whereas pain symptoms were assessed by the Visual Analogic Scale (VAS 0-10). Statistical analysis was performed to investigate possible associations between QoL and characteristics of bowel nodules (dimension, location, and evidence of stenosis) as well as type and length of eventual medical therapy. Results Patients with BE had a satisfying overall QoL with a mean EHP-5 score of 105.42 ± 99.98 points and VAS lower than 3 for all pain domains; additionally, they did not show a significant impartment of bowel function with mean BENS score of 4.89 ± 5.28 points. Notably, patients under medical therapy had a better QoL than patients without therapy (p

There are many modern and traditional methods in valuing the performance of the company among them EVA, CVA are modern methods where as EPS, ROI, ROE etc. are some of the traditional methods. modern and traditional methods are not only used to check the performance of a company but it also used in investment decisions by the investors. Stern Stewart, managing partner of M/s Stern Stewart & Co. introduced a modified concept of economic profit in 1990 in the name of Economic Value Added (EVA) as measure of business performance and CVA is only a cash consideration in EVA. In this paper an attempt is made to study which method is used by the investors while taking the investment decisions i.e. traditional methods are modern methods. 100 respondents (Investors) are questioned and collected their views, we are assuming that there is no impact of traditional or modern methods while taking investment decisions by the investors.

Hybrid woven kenaf-carbon composite were fabricated in this study using epoxy resin as matrix. Effects of different fabric material namely weave designs (plain and satin) and fabric counts (5×5 and 6×6) on the properties of laminated woven kenaf polymer composite were evaluated. This study evaluates the mechanical and morphological properties of hybrid fabric kenaf-carbon from kenaf yarn of 500tex. Kenaf and carbon fabrics were used in this work, where vacuum infusion technique was selected to prepare the composite and epoxy resin was used as a matrix. The fibre weight content is 30% and four specimens were prepared for each samples and tested for their tensile, flexural, and impact strengths. The morphological properties of composites were analysed through the scanning electron microscope (SEM). The results revealed that plain woven fabric is favourable in terms of tensile and impact strengths compared to satin woven fabric. Meanwhile, 5×5 of fabric count gives better flexural modulus than composite fabricated with 6×6 fabric count. The morphologies of the fractured surface investigated by SEM demonstrated better adhesion properties and less fibre pull-out on plain woven fabric.

Climbing is an Olympic discipline in full development and multidisciplinary in nature, in which the influence of body composition and nutritional status on performance has not yet been clarified despite the quest for low weight in anti-gravity disciplines such as climbing. The present study aimed to do a nutritional (3-day dietary diaries) and body composition (ISAK profile) assessment of sport climbing athletes of different genders and sport levels. The mean age of the forty-six Spanish climbers (22 men and 24 women) was 30 years (SD: 9) with 7.66 years of experience (SD: 6.63). The mean somatotype of the athletes was classified as balanced mesomorph. Negative correlations were observed between fat mass variables and climbing level (p<0.01), and positive correlations with forearm circumference (p<0.05). Mean energy availability (EA) was 33.01 kcal-kg FFM1-d1 (SD: 9.02), with 55.6% of athletes in suboptimal EA status and 35.6% in low energy availability (LEA) status. Carbohydrate and protein intakes were below recommendations in 57.8% and 31.1% of athletes, respectively. There were deficient intakes of all micronutrients except phosphorus in males. These findings suggest that climbing athletes are at high risk of developing low energy availability states and concomitant problems. Optimal nutritional monitoring may be advisable in this type of athlete to try to reduce the risk of LEA.

This systematic review explores the cross-cultural validation of neuropsychological assessments and their clinical applications in cognitive behavioral therapy (CBT), focusing on culturally adapted CBT (CA-CBT) across diverse populations and settings. Methods: Following the PRISMA guidelines, a comprehensive search was conducted in multiple academic databases, including PubMed, PsycINFO, Scopus, and Web of Science. Keywords related to cognitive-behavioral therapy, cultural adaptation, and specific populations were used. Inclusion criteria encompassed randomized controlled trials (RCTs) and pilot studies that assessed CA-CBT for various mental health conditions. Results: The review included studies involving Chinese Americans, Latino caregivers, Syrian refugees, Jordanian children, Malaysian Muslims, Afghan refugees, Iraqi women, Japanese children and adolescents, and Tanzanian and Kenyan children. CA-CBT demonstrated significant effectiveness in reducing symptoms of depression, anxiety, PTSD, and psychosis. For instance, Research has shown that CA-CBT is more effective than standard CBT in reducing depressive symptoms among Chinese Americans and significantly lowering PTSD symptoms in Syrian refugee women. The method has been well-received and feasible in diverse populations, such as Jordanian children and Afghan refugees. Long-term benefits are promising, with sustained improvements reported in various studies. Additionally, digital and remote delivery methods have demonstrated potential for expanding the accessibility of CA-CBT. Conclusions: CA-CBT is a valuable and effective intervention for diverse cultural populations, significantly improving mental health outcomes. However, future research must address limitations such as small sample sizes, short follow-up periods, and variability in assessment tools. Studies should include larger and more diverse sample sizes, longer follow-up periods, rigorous control groups, and comprehensive outcome measures to further validate and enhance the application of CA-CBT across different cultural contexts.

(1) Exoskeletons offer potential benefits for overhead working tasks, but gender effects or differences are unclear. This study aimed to compare the performance, strain, and comfort of men and women using an upper-body exoskeleton. (2) n=20 female and n=16 male participants performed an overhead drilling task with and without a passive upper-body exoskeleton in a randomized cross-over study. Task performance of different movement phases, perceived exertion, and ease of use were measured to compare gender differences. One and two-way analyses were used to com-pare genders in the different conditions. (3) Gender differences after controlling for BMI in task performance were found for error integrals (p <.001) with higher values in male participants. Moreover, there was a significant interaction effect for gender x exoskeleton use. While females showed performance decrements in aiming with exoskeleton use, the male's performance increased (p=.025). No other gender differences were observed. (4) Gender differences in task performance using an upper-body industrial exoskeleton were less detectable than expected after controlling for BMI, indicating that body composition and anthropometrics might be valuable indicators for per-formance including assisting devices. Moreover, future studies should also integrate the examina-tion of muscle activity to gain more insights into potential gender movement control patterns.

A micromechanical model is implemented to indicate the progressive fatigue problem of a laminated composite with a central circular hole under fatigue loading based on a finite element model. The mechanical properties of the composite lamina are represented based on the characteristics of the fiber and the matrix through a micromechanics model. An appropriate algorithm is then adopted to simulate fatigue damage development in the composite lamina. According to this algorithm, the stress field of the composite subjected to fatigue load is initially obtained using the finite element method. Finally, the predicted results of the stresses in the constituents i.e. fiber and matrix are determined according to the micromechanical bridging model. Finally applying proper damage driving relations leads to damage degree in each element. The proposed model is proven to be successful in the observation of the fatigue behavior with stiffness degradation in each element of the composite in each cycle. Results are reported and validated using those micromechanical models and experimental data available in the literature.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

Research Highlights: The study determined that selective thinning causes different responses, the initial size of the tree released is an influential factor in the growth of species. The temporality of climate and physiological conditions of each species are influential in the growth. It is evident that the defoliation of certain species is an important factor that limits the growth of the species causing thinning to have a negative response. Background and Objectives: The objective is to analyze the behavior of nine timber species, respective to diametric growth after their liberation. This research aims to answer the following questions: (i) How do the selected tree species react to the liberation? (ii) Can the productivity of the trees (diametric growth) be enhanced by liberation? (iii) Are there other factors that influence the diametric growth of the released trees? Materials and Methods: The study was executed in the “Reserva Biológica San Francisco” were 488 trees were monitored, including nine timber species. Therefore, 197 trees were released (removal of competitors) and 251 trees served as reference. To check whether the initial DBH or other factors, like the selective thinning or climate conditions, determine the diameter growth a linear mixed model GLMM was applied. To adjust the linear mixed model a one-way Anova test was executed. Results: Timber species responded differently to the thinning in comparing to reference trees. Therefore, the species analyzed were separated into three groups (positive, negative, and no response to liberation). Conclusions: Liberation potentiates the growth of certain timber species that do not defoliate and considered semi-tolerant to shade. Precipitation and temperature affect all species, but in the defoliate species, it would not be convenient to release them or at least the evidence of these first three years does not show clear differences with control trees. Increase in trees released are higher in trees of the first two diametric classes in all species, this means that larger trees (i.e., older) release does not affect them in a positive way so release should occur in the youngest trees.

Background/Objectives: Adolescence represents a period of heightened vulnerability to risky sexual behaviours. In Portugal, adolescents are initiating sexual activity at increasingly younger ages. Yet, there are no studies evaluating their knowledge about sexually transmitted diseases and prevention methods at an earlier stage of their development. Study how middle school ad-olescents define their sexuality and assess their level of information regarding sexuality, STI, and prevention methods. Additionally, it explores adolescents' sources of information on sexuali-ty-related issues. Methods: A cross-sectional observational study was conducted involving the application of a questionnaire to 750 9th-grade students of Vila Nova de Gaia, Porto, Portugal. The questionnaire covered topics such as perceptions of sexuality, knowledge of sexuality and STI, methods of transmission prevention, and sources of information. Results: The mean age was 14.4 years, with 19.9% reporting having already initiated sexual ac-tivity. Overall, the knowledge about sexually transmitted infections is low, pointing to 7.08 out of a maximum score of 18. Condoms and immunisation are well-recognized preventive measures, but many misconceptions persist. Better knowledge is associated with better attitudes in the likelihood of having sexual intercourse. Conclusions: This study reveals adolescents' limited sexually transmitted infections knowledge, misconceptions about prevention, and reliance on peers and the internet over trusted sources, highlighting the need for comprehensive sexual education in middle school.

Rechargeable solid-state batteries (SSBs) offer enhanced safety, higher energy density, and longer cycle life compared with conventional lithium-ion batteries, making them a promising solution for electric vehicles, grid storage, and other high-demand applications. However, challenges such as interface stability, low ionic conductivity, and manufacturing scalability hinder their commercial viability. This research provides a comprehensive cross-sectional thematic and bibliometric analysis of recent SSB research, focusing on four key areas: electrolyte engineering, electrode engineering, battery architecture, and performance evaluation. By analyzing publications from major databases, this study highlights the latest innovations, including improved solid electrolytes, advanced electrode materials, and novel architectures that enhance both performance and manufacturability. The findings offer valuable insights for researchers, engineers, and industry stakeholders by identifying critical gaps in the field and highlighting future research directions. The work examines progress in interface optimization, ion transport improvements, and scalable production techniques, which are crucial for advancing SSB technology. By presenting a detailed review of key developments and challenges, this study contributes to a deeper understanding of SSB progress and its potential to revolutionize the energy storage industry. The results will guide researchers in targeting high-impact areas and help industry leaders and policymakers strategize the commercial deployment of SSBs in electric vehicles, stationary energy storage, and other applications requiring reliable and efficient energy solutions.

Unmanned aerial vehicle (UAV) systems are widely used in many forest-related fields owing to their cost-intensive and precise surveying technology. This study classified erosion susceptibility (ES) in a timber harvesting area using machine learning (ML) and statistical approaches. In dataset generation for the training and testing process, the digital surface model (DSM) of difference (DoD) for July–June was utilized as a dependent variable, and six terrain maps of the DSM for June were used as independent variables. The ES threshold was set at 5 cm for the binary classification of ES pixels while processing using ML (e.g., random forest and extra gradient boost [XGB]) and statistical (e.g., logistic regression) algorithms for model development. The overall accuracy (OA), receiver operating characteristics, and area under the curve (AUC) were calculated for model accuracy and validation. Although the AUC of all models did not appear acceptable (AUC &gt; 0.7), the XGB model showed the best performance regarding time duration, OA, and AUC by 2 h, 64%, and 0.63, respectively. Despite the low AUC and accuracy of the XGB model, the wheel tracks and edges of the operation road were determined to be susceptible areas in the ES map of the XGB.

Due to satisfactory mechanical properties, low specific weight and other advantages, a substantial utilization of laminated structural composites in many components and equipments of several industry sectors, especially in the past two decades, has been made. This class of materials has a good potential to be an important ally to support scientists and engineers with the main current world challenge: an energy transition process that must occur with sustainability, eco-friendly materials and based on an efficient reduction of greenhouse gas emissions. In this context, a microanalysis (scale length: 10μm to 1mm) of mechanical behavior that considers the multiphase characteristics, at leastwise a matrix and a reinforcement phase, of this kind of composites must be explored, i. e., a heterogeneous material is assumed to predict, for example, the effective tensors of stiffness or compliance by a homogenization process, modeling to damage analyses, studies about progressive delamination and other specific aspects of a composite can be previously investigated using micromechanical approaches. Therefore, the understanding of fundamental micromechanics as well as some advanced models are essential to apply these materials in structural industry components. In this sense, this literature review is designed to investigate and analize intrinsic physical hypothesis and theories behind the main basic and advanced models of polymer laminated composite micromechanics expanding possibilities to the development of more accurate approximations and showing future perspectives to the topic.

In China, preschool teachers have a significant influence on the development of young children aged 3-6. It is imperative to understand their mental health and the factors associated with it to inform policies, optimize their mental well-being, and support their job performance. This study aimed to investigate the factors contributing to anxiety symptoms among preschool teachers. A sample of 393 Chinese preschool teachers (279 females, 114 males) aged 21-56 completed online questionnaires collecting their socio-demographic and work-related information and assessing anxiety symptoms, interpersonal difficulties, personality traits, perceived stress, resilience, and inner strength. Pearson correlation and multiple linear regression analyses identified significant predictors of anxiety symptoms. The prevalence of anxiety symptoms among the studied cohort was found to be 12.2%. Statistically significant factors positively correlated with anxiety symptoms included objective work-related stress (B=0.149, p<.001), interpersonal difficulties (B=0.921, p<.001), perceived stress (B=0.108, p=.001), and neuroticism (B=0.071, p=.002). The findings highlight the urgent need for measures to reduce work-related stress and anxiety. However, when negative mental health predictors were included, the effect of positive psychological factors became nullified. Positive mental health might have a moderating role in such a negative mental health outcome as anxiety. Therefore, further research is required to understand the impact of positive mental health factors more clearly.

Background: The antisense oligonucleotide against APOC3 mRNA volanesorsen was recently introduced to treat Familial Chylomicronemia Syndrome (FCS). Cases of decreased platelet count are reported among patients treated with volanesorsen. The aim of the study is to evaluate platelet function and thrombin generation (TG) assessment in FCS patients receiving volanesorsen. We performed a cross-sectional study on FCS patients treated with volanesorsen. Methods: changes in PLC were assessed from baseline to Tw12 and Tw36. To assess TG, samples were processed by CAT (with PPP-reagent LOW). The results were expressed by the trombogram graphic (thrombin variation over time); lagTime; Endogenous Thormbin Potential(ETP); peak; time to reach peak(ttpeak), startTail e velocity Index. Platelet aggregation was assessed by testing different agonists using turbidimetry method. Results: Four FCS patients and 4 matched healthy controls were included in the present study. Changes in PLC at Tw12 was 30% and 34% at T36w. Thrombin generation results show values in normal range (for patients and controls respectively lagTime:10,42±4,40 and 9,25±0,99; ttPeak:14,33± 4,01 and 13,10±0,67; startTail:32,13±3,54 and 29,46±1,69; velocityIndex:20,21±3,63 and 33,05±13,21; ETP 599,80±73,47 and 900,2±210,99; peak value 76,84±1,07 and 123,30±39,45) and no significant difference between cases and controls. Platelet aggregation test showed values in range with no significant difference with healthy controls Conclusions: Our study showed for the first time that no significant changes in the general haemostasis assessed by TG and in platelet function have been observed in FCS patients receiving volanesorsen.

Cross-lingual sentiment analysis is crucial for understanding and interpreting emotions expressed in text across diverse linguistic contexts. However, cross-lingual sentiment analysis faces challenges such as differences in emotional lexicons, data imbalance, and the need for multi-language sentiment normalization. In this study, we propose a novel approach to address these challenges by leveraging low-resource language training techniques to enhance cross-lingual sentiment analysis. Our method aims to bridge the gap in emotional lexicons by adapting sentiment analysis models to diverse linguistic contexts. Additionally, we tackle issues of data imbalance through innovative data augmentation strategies tailored to each language, and we introduce a multi-language sentiment normalization technique to ensure consistent sentiment interpretation across different languages. Our method achieved state-of-the-art results in twelve languages across four domains, demonstrating superior performance in both text-level and sentence-level sentiment analysis tasks. By conducting comprehensive evaluations across diverse linguistic contexts and domains, we showcase the versatility and effectiveness of our approach in achieving top-tier results in cross-lingual sentiment analysis.

The dispersal potential of crown-of-thorns starfish (CoTS) larvae is important in understanding both the initiation and spread of population outbreaks, and is fundamentally dependent upon how long larvae can persist while still retaining the capacity to settle. This study quantified variation in larval survivorship and settlement rates for CoTS maintained at three different chlorophyll concentrations (0.1, 1.0 or 10.0 µg.L^-1), achieved by varying densities of single-celled flagellate phytoplankton, Proteomonas sulcata. Based on the larval starvation hypothesis we expected that low to moderate algal concentrations would significantly constrain both survival and settlement. CoTS larvae were successfully maintained for up to 50 days post-fertilization, but larval survival differed significantly between treatments. Survival was greatest at intermediate (1.0 µg.L^-1) chlorophyll concentrations, and lowest at highest (10.0 µg.L^-1) chlorophyll concentrations. Rates of settlement were also highest at intermediate (1.0 µg.L^-1) chlorophyll concentrations and peaked at 22 days post-fertilization. Peak settlement was delayed at low chlorophyll concentrations, probably reflective of delayed development, but there was no evidence of accelerated development at high chlorophyll concentrations. CoTS larvae were capable of settling 17-43 days post-fertilization, but under optimum conditions with intermediate chlorophyll concentrations, peak settlement occurred at 22 days post-fertilization. Moderate increases in nutrient concentrations and algal densities may increase the number of CoTS that effectively settle, but are unlikely to influence dispersal dynamics.