Building situated in the flow path of wind is subjected to differential velocity and pressure distribution around the building envelope. Wind effects are influenced and vary for each individual shape of the tall building. Tall building structures are considered as cantilever structures with fixed ends at the ground. Wind exponential velocity acting along the height of the building makes velocity and pressure distribution more complex as the height of the building structure increases. This study discussed the effect of wind on an irregular cross-section shape. The study was conducted numerically with a building model placed in a virtual wind tunnel using the ANSYS (CFX) software tool. Wind effects are investigated on building model situated in a terrain category - II defined in IS: 875 (Part 3): 2015 wind scale model of 1:100 and turbulence intensity is 5 % and power law index α is considered as 0.143. Validation and verification of the study were made by comparing pressure coefficients on faces of a rectangular model of similar floor area and height as taken for a C-plan diamond-shaped model under similar boundary conditions, wind environment, and solver setting of numerical setup. The values of surface pressures generated on the recessed faces of the model and wind flow patterns within the recessed cavity were studied at wind incident angles 0°, 300, 60°, 1050, 1350 & 1800. The critical suction on all the recessed faces was observed to be at a 105° angle of wind attack.

This article is about a framework for determining the degree of realism of any given 1 passenger ride motion discomfort measurement formula. After providing some context and reviewing 2 evidence of deficiency in currently popular ride motion discomfort measurement formulas, the article 3 outlines the research program that needs to be carried out in order to establish such a framework. 4 The research begins with gathering recordings of uncomfortable ride motion episodes encountered in 5 a chosen type of passenger transport service. It then has test subjects compare the episodes via a ride 6 motion simulator and adjust their amplitudes pair wise until they cause equal discomfort. It explains 7 how to take the pair wise amplitude adjustments and determine amplitude adjustments that bring all 8 of the motion episode recordings to a common level of discomfort so that they form a normalized set. 9 Then, the lower the scatter of the scores assigned by any given discomfort measurement formula to 10 the members of that set, the more realistic that formula will be for the chosen service.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

The success of composite materials is attributed to the nature of bonding at the nanoscale and the resulting structure-related properties. This study reports the interaction, electronic, and optical properties of diamond nanothread/polymers (cellulose and epoxy) and boron nitride nanotube/calcium silicate hydrate composites using density functional theory modeling. Our findings indicate that the interaction between the nanothread and polymer is due to van der Waals-type bonding. Minor modifications in the electronic structures and absorption spectra are noticed. Conversely, the boron nitride nanotube and calcium silicate hydrate composite display an electron-shared type of interaction. The electronic structure and optical absorption spectra of the diamond nanothread and boron nitride nanotube in all configurations studied in the aforementioned composite systems are well maintained. Our findings offer an electronic-level perspective into the bonding characteristics and electronic-optical properties of diamond nanothread/polymer and boron nitride nanotube/calcium silicate hydrate composites for developing next-generation materials.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

The wind flow patterns and pressure distribution around a plus-shaped building are significantly influenced by the dimensions of its re-entrant corners and the overall building height. The present study aims to find the wind effects and study of the pressure distribution with different flow patterns. Plan area of the building is around 300 square meter while the height of the building is 50 meters by keeping the equal length of the re-entrant corners. The research is performed using ANSYS CFX academic version and the results are depicted in various forms such as pressure coefficient (Cpe), stream lines in both vertical as well as in specific surface and pressure contours. The analysis is carried out by varying the wind incident angles, from 0° to 90° at the interval of 15°. The building dimension are scale down to perform the test on length scale of 1:100. Since the considered building model exhibits symmetry along both the axes, present study mostly emphasis on examining re-entrant corners located in the building. This method yields valuable information about how air circulates and how pressure is distributed across a broad spectrum of wind angles. This study provides valuable insights into flow circulation and pressure distribution for a wide range of wind angles.

This paper illustrates an experimental activity for the closed-loop position control of an actuator made using shape memory alloy (SMA) wire. A solution with the self-sensing effect was implemented to miniaturize the systems, i.e., without external sensors. A proportional control algorithm was initially used, demonstrating the idea's feasibility: the wire can behave simultaneously as an actuator and sensor. An experimental investigation was subsequently conducted for the optimization of the developed actuator. As for the material, a Flexinol wire, Ni-Ti alloy, with a diameter of 0.150 mm and a length of 200 mm, was used. Preliminarily, a characterization of the SMA wire at constant and variable loads was carried out: the characteristics detected are elongation vs. electric current and elongation vs. electrical resistance. The control system is PC-based with a data acquisition card (DAQ). A drive board has been designed and built to read the wire's electrical resistance and power it by pulse width modulation (PWM). A notable result is that the actuator works with good precision and in dynamic conditions, even when it is called to support a load up to 65% different from that for which the electrical resistance-length correlation has previously been experimentally obtained, on which the control is based. This opens up the possibility of using the actuator in a counteracting configuration with a spring, which makes hardware implementation and control management simple.

This study explored the effects of cryogenic treatment on the microstructure, hardness, and wear-resistance of diamond-like carbon (DLC) by cryogenically treating NAK 80 mold steel coated with DLC. Raman spectroscopy analyzed the structure of the DLC film. Nanoindenter analyzed the hardness and Young’s modulus of the film, and their relationship determined the wear resistance. Wear test assessed the wear rate and friction coefficient of the DLC film. The results showed that cryogenic treatment increased the rate of carbide precipitation and refined the grain structure. Raman spectroscopy indicated that the Raman intensity rate (I_D/I_G) of treated DLC films was smaller than those without cryogenic treatment. When the sp3 bond increased, the hardness and wear-resistance of the DLC film also increased.

The role of natural factors mainly solar eleven-year cycle variability, and volcanic eruptions on two major modes of climate variability the North Atlantic Oscillation (NAO) and El Niño Southern Oscillation (ENSO) are studied for around last 150 years period. The NAO is the primary factor to regulate Central England Temperature (CET) during winter throughout the period, though NAO is impacted differently by other factors in various time periods. Solar variability indicates a strong positive influence on NAO during 1978-1997, though suggests opposite in earlier period. Solar NAO lag relationship is also shown sensitive to the chosen times of reference and thus points towards the previously proposed mechanism/ relationship related to the sun and NAO. The ENSO is influenced strongly by solar variability and volcanic eruptions in certain periods. This study observes a strong negative association between the sun and ENSO before the 1950s, which is even opposite during the second half of 20th century. The period 1978-1997, when two strong eruptions coincided with active years of strong solar cycles, the ENSO, and volcano suggested a stronger association, and we discussed the important role played by ENSO. That period showed warming in central tropical Pacific while cooling in the North Atlantic with reference to the later period (1999-2017) and also from chosen earlier period. Here we show that the mean atmospheric state is important for understanding the connection between solar variability, the NAO and ENSO and associated mechanism. It presents a critical analysis to improve knowledge about major modes of variability and their role in climate. We also discussed the importance of detecting the robust signal of natural variability, mainly the sun.

A flow chart is presented depicting coupling in ocean-atmosphere system, initiated by solar decadal variability that involves El Niño Southern Oscillation (ENSO). Possible mechanisms for Canonic ENSO, Modoki ENSO and Canonic-Modoki ENSO are proposed considering their relevance to the decadal variation of Hadley, Walker circulation and mid-latitude jets. It also discusses subsequent teleconnections by ENSO on Indian Summer Monsoon (ISM) with a special emphasis on later two decades of the last century. Possible mechanisms relating to a disruption of the usual ENSO-ISM teleconnection for those decades are emphasised; the role of volcanos and the change in the sun- NAO (North Atlantic Oscillation) connection were attended. The regional Hadley circulation, via the NAO in the northern hemisphere and Indian Ocean Dipole in the southern hemisphere, during that period, may have a role in the change in ISM behaviour- which though captured in observation but missed by models. The representation of flow chart helps to improve understanding of various types of ENSO in both temporal as well as spatial scale. The overall study subsequently can benefit the modelling community by not only improved the representation of ENSO in models but also better representation of ISM teleconnection via regional Hadley cell.

In this research paper we describe the development phase of a low-cost LoRa IoT solution applied to a kindergarten school with three years results. A set of sensors solution was developed in a LoRa communication board, battery powered, providing a simplified setup process. These sensors were used in order to measure temperature, humidity, luminosity, air quality and presence. Also, energy monitor solutions were integrated. The acquired data is transmitted and analysed for knowledge extraction, identifying savings and other related KPIs. From data, automatic saving actions were performed towards heating and cooling systems, lighting and a set of if-then actions were developed for automatic cost-saving actions, based on infrared signals to heating/cooling systems using some procedure of external command devices. This approach avoids the usage of proprietary vendor solutions in a flexible approach that can easily be deployed to any building facility. This is an important achievement since most of the building consumption is based on heating and cooling systems. In a three years test of the solution, the total energy consumption savings surpassed 20%

Chelating gels may assist initially in root canal preparations to help establish a glide path. While irrigation surveys have investigated liquid chelators, and gels to a minor extent, no endodontic survey has focused on EDTA gels, and why clinicians use them. All 395 members of the Australian Society of Endodontology (ASE) were emailed an 11-question survey concerning chelation gel usage via Qualtrics. Paper copies were also distributed at ASE events. Descriptive statistics was performed for practitioner and chelating gel data. Cross-tabulations of practitioner type with case percentage usage of gels were analyzed with the chi square test (adjusted P value <0.0083). The overall response rate was 181/395 (46%). For 174 eligible responses, those who never/rarely used a gel was: endodontic residents 12/14 (86%), endodontists 53/71 (75%), general dentists 39/86 (45%), and other members 0% (0/3). Most gel users said that gels helped establish a glide path. Those who never/rarely used chelating gels commented that they held no benefits over liquid EDTA. Endodontists were less likely to use a chelation gel than general dentists (P <0.0083). Older members had higher gel usage than younger members (P <0.0083), indicating a possible trend to diminished gel usage over time amongst ASE members.

Earth’s climate cannot be ignored any longer. Policies are vital in order to mitigate the negative effects of climate change. The energy crisis created by the Russo-Ukrainian war and pandemic affected the EU and its member states. The focus is more than ever on its energy policies and independence. The EU revised the energy strategy in response to Russia’s blackmail, and it sped up all the processes for energetic independence from Russia. This benefited the climate change policies the most, as all the measures involved reducing energy consumption and increasing renewables, thus contributing to reducing greenhouse gas emissions. As a member state of the EU, Romania is committed to complying with EU regulations. With a high degree of energy independence compared with the other EU members, Romania plans to become a regional energy provider and modernize the energy infrastructure internally as a response to Russia’s unprovoked aggression. The measures that the EU and Romania implemented after the war started in 2022 have come to fruition, and the effects are becoming visible a year later. This study aims to study the energy strategy of Romania in correlation with the EU strategy in the turbulent period of pandemics and war between 2019 and 2023, with the latest available data.

Enteroviruses (EVs) are viruses of the family Picornaviridae that cause mild to severe infections in humans and in several animal species, including nonhuman primates (NHPs). We conducted a survey and characterization of enteroviruses circulating between humans and great apes in the Congo. Fecal samples (N=24) of gorillas and chimpanzees living close to or distant from humans in three Congolese parks were collected, as well as from healthy humans (N=38) living around and within these parks. Enterovirus were detected in 29.4% gorilla and 13.15% human feces, including wild and human-habituated gorillas, local humans and eco-guards. Two identical strains were isolated from two humans come from two remote regions. Their genomes were similar and all genes showed their close similarity to Coxsackieviruses except for 3C, 3D and 5’UTR region where they were most similar to poliovirus 1 and 2, suggesting recombination. Recombination events were found between these strains, poliovirus 1 and 2 and EV-C99. The same EV- C species detected in both humans and apes in different regions suggest a clonal distribution of the virus in Congo.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

In this paper, a new type of self-excited thermomechanical oscillator containing an oscillating shape memory alloy (SMA) filament with two symmetrically arranged spheres is investigated. The self-excitation of the oscillations is due to a heater of constant temperature, which causes periodic contractions of the filament when it approaches it. The contracted filament moves away from the heater a distance sufficient to cool it. Under the action of the weight of the spheres, the cooled filament re-approaches the heater, causing the above processes to repeat periodically. On the basis of experimental studies, approximating functions of the heater's heat field distribution are derived. A dynamic model of the oscillator has been created, in which the minor and major hysteresis in the SMA alloy and the distribution of the heat field around the heater have been taken into account. By numerical solutions of the differential equations, the laws of motion of the spheres are obtained. The displacements of the spheres in two perpendicular directions were measured using an experimental system. The obtained experimental results validate the proposed dynamic model and its assumptions with a high degree of confidence. Conclusions are drawn about the stochastic nature of the oscillations due to the hysteresis properties of the SMA and the temperature variation of the natural frequency of the oscillating system.

Magneto-rheological dampers (MR-dampers) are increasingly used in construction applications to reduce the dynamic response of structures to seismic activities or severe wind loading. Sensors attached to the structure will signal the computer to supply the dampers with electric charge that transfers the MR fluid to a near-solid material with different physical and mechanical properties (viscoelastic behavior). Control algorithms govern the fluid to near-solid conversion, which controls the behavior of the damper, and the performance of the structure under the seismic or wind loading event. The successful optimization of control parameters minimize the overall structural response to dynamic forces. The main objective of this research is to change the output behavior of specific floors within a building subjected to seismic excitation by optimizing the MR-dampers control parameters to impact the behavior of a specific floor or number of floors within the building. The adjustment of control parameters to attain this objective was validated in multiple case studies throughout this research. The successful implementation of the research outcome will result in optimized MR-damper design to meet the performance-based criteria of building projects.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.

Hepatitis C virus (HCV) is a major public health threat associated with serious clinical consequences worldwide. The WHO reports an estimated 58 million people globally living with chronic hepatitis C virus (HCV) infection, with 1.5 million new cases and over 350,000 deaths annually due to HCV-related diseases. Despite the existence of multiple diagnostic methods, the accessibility of diagnosis and treatment is often hindered across the continent by limited resources, insufficient healthcare infrastructure, and low public awareness of Hepatitis C virus Hepatitis C virus infection is a major public health concern in African countries, which have the highest prevalence rates of HCV in the world (1–26%). Egypt, African country which had the highest prevalence of Hepatitis C virus infection in the world. Its national hepatitis C elimination initiative emerges as an exemplary case of success an having screened over 60 million individuals, and treated more than 4 million, thereby markedly diminishing both the prevalence and incidence of the disease. The strategies employed by Egypt offer critical insights and adaptable frameworks for other African Countries facing analogous challenges. The Aim of this Review is to highlight the triumphs and hurdles of Egypt's approach, while also providing strategic guidance for African Countries to accelerate the journey towards the eradication of hepatitis C.

In August 4 2011, United Nations Environmental Program (UNEP) submitted an unprecedented, scientific, groundbreaking Environmental Assessment Report (EAR) of Ogoniland, to the Nigerian government. This was the outcome of a 14–month intensive evaluation of the extent of pollution. It was intended that UNEP’s recommendations would be implemented to restore the devastated environment, on the one hand, and on the other, counteract the numerous environmental health issues that have for decades, plagued Ogoniland. However, five years post EAR, and, despite the seriousness of the situation, no significant resolution has occurred, both on the part of the government, and on the part of Shell Petroleum Development Company (SPDC) or Shell. To date, millions of Niger Delta residents, particularly those living in the oil-bearing communities, continue to suffer severe consequences. Although, the assessment was conducted in Ogoniland, other communities in the Niger Delta are also affected. This article explores prevailing issues, using Ogoniland (a microcosm of the Niger Delta) as an example. A multidisciplinary approach for sustainable mitigation of environmental health risks in the Niger Delta is paramount, and Environmental Management tools offer valuable strategies. Adopting UNEP’s recommendations for addressing environmental health problems requires implementing the Environmental Management/Environmental Management System (EM/EMS) model.

In the present study, a numerical model was developed to predict the flow pattern inside a broiler building. The model intends to predict the velocities fields inside the domain and ammonia (NH3) emitted or released by litter from poultry housing. The numerical model developed in Computational Fluid Dynamics (CFD) commercial code, intends to represent a commercial broiler building, and intends to simulate the 3D and heat transfer, in steady state flow. The evaporative cooling pads were also included in the model. The validation of the model was based in experimental measurements obtained in previous studies. The simulations were focused on Summer, Winter and also Mid-Season situation. The numerical results of NH3 concentration were compared with the experimental measurements, and a quite good agreement was verified. The numerical results allowed the characterization of: the inside flow pattern developed for the summer and winter situation; the inside NH3 distribution, and the velocity field distribution inside the broiler building. It was found that NH3 concentration increases along the tunnel, especially in low flow rate imposed from the exhaust fan. Also, it was verified that the low velocities inside domain are no sufficient to remove the gaseous pollutants.

Bamboo is the building material of the past and future. It offers numerous properties that make it versatile for various applications, including construction. Its impressive strength-to-weight ratio enables it to bear substantial loads and stresses, while its good elasticity allows efficient energy absorption. However, its mechanical properties can vary based on factors such as species, age, locations, methods, and treatment. Treating bamboo is essential to enhance its properties and durability. The literature provides various natural and chemical treatments which enhanced some of the properties but also reported a drawbacks on higher temperature, content and duration. This paper reviewed 57 articles from Scopus database, specifically focusing on article-document type publications from the years 2003 to 2023. Additional references were also incorporated to address concerns in properties, treatment and standards to provide systematic understanding. MATLAB was utilized for data text analytics. With extensive assessment on the articles, the following gaps and concerns were observed and recommends for further study and assessment such as for bamboo properties, the development of centralized guidelines and procedures for the preparation and processing; exploration of alternative materials to reinforce bamboo without compromising its ductility; development of joint connections, and testing of mechanical properties considering seismic, wind and vibration. For treatment methods, the standardization of procedures using natural, chemical or combination. Lastly, for bamboo codes and standards, assessment of existing codes and standards for testing the mechanical properties of bamboo highlighting the potential limitations and areas, uniformity, differences with all existing similar standards. By filling these gaps, it can support the reliability and robustness of bamboo as a sustainable material, fostering its promotion and adoption in construction industry.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

In this paper, a new approach to retrieve semantic images based on shape and geometric features of image in conjunction with multi-class support vector machine is proposed. Zernike moment as shape feature is to verify the invariance of objects for silhouette image. In addition, a set of geometrical features is to explore the objects shape using two features of rectangularity and circularity. Then the extracted features are normalized and employed for multi-class support vector machine either for learning or retrieving processes. The retrieving process relies on three main tasks which namely Query Engine, Matching Module and Ontology Manger, respectively. Query Engine is to build the input text or image query using SPARQL language. The matching module extracts the shape and geometric features of image’s objects and employ them to Ontology Manger which in turn inserts them in ontology knowledge base. Benchmark mammals have been conducted to empirically conclude the outcome of proposed approach. Our experiment on text and image retrieval yields efficient results to problematic phenomena than previously reported.

Within microeukaryotes, genetic and functional variation sometimes accumulate more quickly than morphological differences. To understand the evolutionary history and ecology of such lineages, it is key to examine diversity at multiple levels of organization. In the dinoflagellate family Symbiodiniaceae, which can form endosymbioses with cnidarians (e.g., corals, octocorals, sea anemones, jellies), other marine invertebrates (e.g., sponges, molluscs, flatworms), and protists (e.g., foraminifera), molecular data have been used extensively over the past three decades to describe phenotypes and to make evolutionary and ecological inferences. Despite advances in Symbiodiniaceae genomics, a lack of consensus among researchers with respect to interpreting genetic data has slowed progress in the field and acted as a barrier to reconciling observations. Here, we identify key challenges regarding the assessment and interpretation of Symbiodiniaceae genetic diversity across three levels: species, populations, and communities. We summarize areas of agreement and highlight techniques and approaches that are broadly accepted. In areas where debate remains, we identify unresolved issues and discuss technologies and approaches that can help to fill knowledge gaps related to genetic and phenotypic diversity. We also discuss ways to stimulate progress, in particular by fostering a more inclusive and collaborative research community. We hope that this perspective will inspire and accelerate coral reef science by serving as a resource to those designing experiments, publishing research, and applying for funding related to Symbiodiniaceae and their symbiotic partnerships.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

The carbohydrate antigen Sda is expressed on cells and secretions of the vast majority of Caucasians. The epitope is formed by a terminal GalNAc residue β4-linked to a α3-sialylated galactose. Different carbohydrate chains N- or O-linked to glycoproteins can be terminated by this epitope. The final step of Sda biosynthesis is catalyzed by the GalNAc transferase B4GALNT2. In this review, we will discuss the multifaceted aspects of B4GALNT2/Sda biology. In particular, we will see its implications in fertility and pregnancy, in susceptibility to infectious diseases, in chronic kidney diseases and in Duchene muscular dystrophy. In particular, we will show its regulation and prognostic implications in cancer.

Reducing the levels of toxic chemicals that cause adverse health and environmental impacts is a challenge for the international community. There is a need of a global strategy. Indeed, too often the problems associated to the exposure of chemical substances is recognized a posteriori, in the presence of consequences already observed. The prediction of the likely effects of chemical exposure on human health is based on classical tests with animals, which are time and money consuming, may deviate from an accurate prediction towards humans, and arises ethical concerns. Regulations are now considering the adoption of in silico (or computational) methods, which can be used for prioritizing substances according to the probability to be toxic for the biosphere. Several initiatives have prioritized chemicals, typically based according to some criteria, such as chemicals which may be endocrine disruptors, or persistent, bioaccumulative, or toxic (PBT). However, these initiatives focused on a certain range of adverse properties, and covered a certain number of substances only. We applied a set of largely validated and widely used predictive methods to large collections of chemicals: (i) to about 340,000 with a defined function, and (ii) to about 6 millions, which have been synthetized. The aim of this study is to quantify the putative impact of existing and future chemicals on towards human health, ecological and environment properties. The impact on the environment is the cause of major concern. This is the case of pesticides and hazardous, which is quite expected; however, also pharmacologically active candidate compounds of natural origin may have a high level of ecotoxicity. Pesticides and hazardous are also the categories of higher concern for humans, followed by pharmaceuticals. The pesticides and the hazardous are the categories of higher concern also on the environmental point of view. The results of our analysis could be the basis for the identification of new safety rules.

Copper-catalyzed and organocopper-involved reactions are of great significance in organic synthesis. To have a deep understanding of the reaction mechanisms, the structural characterizations of organocopper intermediates become indispensable. Meanwhile, the structure-function relationship of organocopper compounds would advance rational design and development of new Cu-based reactions and organocopper reagents. Compared to the mono-carbonic ligand, the C,N- and C,C-bidentate ligands better stabilize the unstable organocopper compounds. The bidentate ligands can chelate to the same copper atom via ?2-mode, forming a mono-cupra-cyclic compounds with at least one acute C-Cu-C angle. When the bidentate ligands bind to two copper atoms via ?1-mode at each coordinating site, the bimetallic macrocyclic compounds will form nearly linear C-Cu-C angles. The anionic coordinating sites of the bidentate ligand can also bridge two metals via ?2-mode, forming organocopper aggregates with Cu-Cu interactions and organocuprates with contact ion pair structures. The reaction chemistry of some selected organocopper compounds is highlighted, showing their unique structure-reactivity relationships.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

Melting phase relations of the diamond-forming system olivine (Ol) – jadeite (Jd) – diopside (Di) – (Mg, Fe, Ca, Na)-carbonates (Carb*) – (C-O-H-fluid) are studied in experiments at 6.0 GPa in the polythermal section Ol74Carb*18.5(C-O-H)7.5 - Omp74Carb*18.5(C-O-H)7.5, where Ol = Fo80Fa20, Omp (omphacite) = Jd62Di38 and Carb* = (MgCO3)25(FeCO3)25(CaCO3)25(Na2CO3)25. Peritectic reaction of olivine and jadeite-bearing melt with formation of garnet has been determined as a physico-chemical mechanism of ultrabasiс-basiс evolution of the diamond-forming system. In the process CO2-component of the supercritical C-O-H-fluid can react with silicate components to form additional carbonates of Mg, Fe, Ca and Na. Solidus temperature of the diamond-forming system is depressed to 1000-1020°C by joint effect of the H2O-fluid and carbonate constituents thereof. The experimentally recognized peritectic mechanism of ultrabasiс-basiс evolution of the diamond-forming system explains the origin of the associated paragenetic inclusions of peridotite and eclogite minerals in diamonds as well as the xenoliths of diamond-bearing peridotites and eclogites of the kimberlitic deposits of diamond. The diamond-forming systems have formed with the use of material of the upper mantle native peridotite rocks. In this case the capacity of the rocks to run the peritectic reaction of olivine was transmitted with silicate components to the diamond-forming systems.

The aim of this review is to provide a survey of the recent advances and the main remaining challenges related to the ultrananocrystalline diamond (UNCD) nanowires and other nanostructures which exhibit excellent capability as the core components for many diverse novel sensing devices, due to the unique material properties and geometry advantages. The doping introduced in the gas phase during deposition promotes p-type or n-type conductivity. With the establishment of the UNCD nanofabrication techniques, more and more nanostructure based devices are being explored in measuring basic physical and chemical parameters via classic and quantum methods, as exemplified by gas sensors, ultraviolet photodetectors, piezoresistance effect based devices, biological applications, and nitrogen-vacancy color center based magnetic field quantum sensors. Highlighted finally are some of the remaining challenges and future outlook in this area.

Hierarchical tungsten oxide assemblies such as spindle-like, flowers with sharp petals, nanowires and regular hexagonal structures are successfully synthesized via a solvothermal reduction method by simply adjusting the reaction conditions. On the basis of the experimental results, it is determined that the reaction time significantly influences the phase transition, microstructure and photocatalytic activity of the prepared samples. The possible mechanisms for the phase transition and morphology evolution process have been systematically proposed. Moreover, the as-prepared products exhibit significant morphology-depended photocatalytic activity. The flower-like W18O49 prepared at 6 h possesses large specific surface area (150.1 m²g^-1), improved separation efficiency of electron-hole pairs and decreased electron-transfer resistance by the photoelectrochemical measurements. As a result, the flower-like W₁₈O₄₉ prepared at 6 h exhibits the highest photocatalytic activity for the degradation of Methyl orange aqueous solution. The radical trap experiments showed that the degradation of MO was driven mainly by the participation of h⁺ and •O²⁻ radicals.

This paper performs non-parametric Mann Kendall (MK) trend analysis of historical hydroclimatic data (1961-2016), an ensemble climate model validation and a computation of 16 Expert Team on Climate Change Detection and Indices (ETCCDI) temperature and rainfall extremes indices. The climate indices are evaluated using MK test and annual trend analysis for two Representative Concentration Pathways (RCP4.5 & RCP8.5) future scenarios from 2020 to 2045 over Mono River Basin (MRB) in Togo. The annual and seasonal trend analyses are assessed on historical potential evapotranspiration, mean temperature, rainfall and discharge data. Results show positive and negative trends of hydroclimatic data over MRB from1961 to 2016. Mean temperatures increase significantly in most of the stations while a negative non-significant trend is noticed for rainfall. Meanwhile, the discharge presents a significant seasonal and annual trend for three gauge stations (Corrokope, Nangbéto and Athiémé). Validation of the ensemble climate models reveals that the model under-estimates observations at Sokode, Atkakpamé and Tabligbo stations, however linear regression and spatial correlation coefficients are higher than 0.6. Moreover, the percentage of bias between climate model and observations are less than 15% at most of the stations. Finally, the computation of extreme climatic indices under RCP4.5 and RCP8.5 scenarios shows a significant annual trend of some extreme climatic indices of rainfall and temperature at selected stations between 2020 and 2045 in the MRB. Therefore, relevant governmental politics are needed to elaborate strategies and measures to cope with projected climate changes impacts in the country.

β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of &lt;1 μs, and density of 6.44 g/cm3. In this study, 2-inch diameter β-Ga2O3 single crystals were prepared by oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Since the discovery of transposable elements (TEs) in Maize in the 1940s by Barbara McClintock [1] transposable elements have been described as junk, as selfish elements with no benefit to the host, and more recently as major determinants of genome structure and genome evolution. TEs are DNA sequences that are capable of moving to new sites in the genome and make additional copies while doing so. To limit the propagation of TEs, host silencing mechanisms are directed at transposon-encoded genes that are required for mobilization. The mutagenic properties of TEs, the potential of TEs to form new genes and affect gene expression, together with the host silencing mechanisms shape eukaryotic genomes and drive genome evolution. While TEs constitute more than half of the genome in many higher eukaryotes, transposable elements in the nematode C. ele-gans form a relatively small proportion of genome, about 15% [2]. Genetic studies of transposon silencing and the discovery of RNAi in C. elegans, propelled C. elegans to the forefront of studies of RNA-based mechanisms that silence TEs. Here, I will review the transposable elements that are present and active in the C. elegans genome, and the host defense mechanisms that silence these elements.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

Industrial hemp (Cannabis sativa L.) is an attractive candidate for sustainable pest management due to its abundance of bioactive compounds with potential pesticidal properties. Solvent choice has a significant impact on the extraction efficiency of bioactive compounds. Deep Eutectic Solvents (DESs) are gaining popularity in extraction because they are safe and environmentally friendly, making them viable alternatives to organic solvents (OSs). This research first compared the extraction efficiency of OSs on the extraction of phytochemicals from the infloresences of two hemp varieties, Citrus and Cherry Dwarf. Inflorescences were extracted using three OSs, ethanol, ethyl acetate, and hexane. The highest level of cannabidiol (CBD; 0.69%) was extracted from Cherry Dwarf using ethanol while the level of delta-9 tetrahydrocannabinol THC (0.19%) was essentially the same in both. Therefore, Cherry Dwarf was selected to compare the extraction efficiency of DESs to the OSs. The DESs were choline chloride/ethylene glycol, citric acid/ethylene glycol, menthol/lauric acid, choline chloride/urea and choline chloride/glycerol. In the targeted analysis, choline chloride/ethylene glycol extracted the highest amount of CBD (0.87%) followed by choline chloride/urea (0.78%). As some DESs outperformed ethanol, the popular solvent for extracting cannabinoids, DESs are viable candidates to replace organic solvents.

Basic mechanisms of laser interaction with synthetic diamond are reviewed. The features of the major regimes of diamond surface etching are considered. Besides well-known graphitization and ablation processes, the nanoablation and accumulative graphitization, which attracted the attention relatively recently, are described in detail. The focus is placed on femtosecond (fs) laser exposure which provides a formation of dense cold electron-hole plasma in focal zone and a minimum overheating in surrounding area. This potentially opens the way to develop unique laser-based technologies combining physical and chemical processes for precise surface treatment and functionalization. The physical limitations determining how precisely the diamond surface can be treated by short-pulsed laser radiation and possible pathways to overcome them with the end to remove ultra-thin layers of the material are discussed. Particular attention is devoted to the novel possibility to induce local formation of point active defects - nitrogen vacancy (NV) complexes in the laser-irradiated zone. Both the regimes of NV centers generation with and without graphitization of diamond lattice are reviewed. It is thus shown that intensive pulse laser radiation is a perfect tool for processing of synthetic diamonds on the micro, nano and even on an atomic level that can be well controlled and managed.

Carbon nanomaterials with a different character of the chemical bond – graphene (sp2) and nanodiamond (sp3) are the building bricks for a new class of all-carbon hybrid nanomaterials, where the two different carbon networks with the sp3 and sp2 hybridization coexist, interact and even transform into one another. The unique electronic, mechanical, and chemical properties of the two border nanoallotropes of carbon ensure the immense application potential and versatility of these all-carbon graphene – diamond nanomaterials. The review gives an overview of the current state of the art of graphene – diamond nanomaterials, including their composites, heterojunctions, and other hybrids for sensing, electronic, energy storage, and other applications. Also, the graphene-to-diamond and diamond-to-graphene transformations at the nanoscale, essential for innovative fabrication, and stability and chemical reactivity assessment are discussed based on extensive theoretical, computational, and experimental studies.

Diamond-like carbon (DLC) films have a promising tribological application in green precision manufacturing, but their toughness represents a serious issue in the way of their application perspective. The film thickness is on the micrometer scale and makes conventional methods unsuitable for its toughness characterization. The absence of an accepted method for characterizing the DLC toughness has hindered the related research on the development of toughening methods and understanding the mechanism. This work intends to explore a relatively simple and acceptable characterization method to measure the film toughness. Moreover, toughening mechanisms of DLC films are proposed during the characterization to reveal the toughening mechanism. The toughness can be fully characterized through combining impact toughness and scratch toughness. The impact toughness can be obtained by observing the size of the indentation and the crack state around the indentation in the impact experiment. The scratch toughness could be assessed by combining the scratch morphology and Crack Propagation Resistance (CPRS). The improvement of film toughness should be carried out from two aspects: preventing microcrack initiation and suppressing crack propagation. Appropriate doping of non-carbide metal particles can effectively improve the toughness of the film, and there are seven main factors affecting the toughening of the film. Five toughening mechanisms of non-carbide metals from film preparation to test stage are revealed during the investigation of the change patterns.

This article attempts to formulate a mathematical model for a potential explanation regarding the unavoidable impact of a rigid body's peculiar shape on the seamless flow over it. The solid body completely immersed in a Newtonian fluid and respectively has a relative open circuit flow on it will typically experience various observable phenomena like flow separation, flow transition, down-wash, stalling at the higher angle of attack, stalling velocity and how cambered airfoil can typically generate lift at a zero incidence angle. This article respectively represents an understanding of the laminar flow over a rigid body's external surface with due respect to its distinctive shape and size. This working paper formulates a more realistic and simplified mathematical model for open circuit laminar flow over a body, based on the historical data of aerodynamics and theoretical mechanics. This is intended to properly estimate forces on the continuous surface of the body in a laminar flow, to properly explain, understand and predict mentioned phenomena. Most of all the mechanism of streamline formation and its deformation with due regards to flow, shape and size of the body in an open-circuit laminar are formulated mathematically to enhance better design theory which can reduce experimentation while designing a streamlined body.

In this paper, we present a new concept of the generalized core orthogonality (called the C-S orthogonality) for two generalized core invertible matrices $A$ and $B$. $A$ is said to be C-S orthogonal to $B$ if $A^{\tiny\textcircled{S}}B=0$ and $BA^{\tiny\textcircled{S}}=0$, where $A^{\tiny\textcircled{S}}$ is the generalized core inverse of $A$. The characterizations of C-S orthogonal matries and the C-S additivity are also provided. And the connection between the C-S orthogonality and C-S partial order has been given using their canonical form. Moreover, the concept of the strongly C-S orthogonality is defined and characterized.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Saline water irrigation contributes significantly to forage yield. However, the salinity threshold for safe saline water irrigation of tall wheatgrass in coastal saline-alkaline land remains unclear. In this study, 2 g L‒1, 3 g L‒1, 4 g L‒1, 5 g L‒1, and 8 g L‒1 saline waters were used for irrigation. Two irrigations with 2+3 g L‒1 saline waters produced the highest yield, followed by one irrigation with 4 g L‒1 or 5 g L‒1 saline water. After rainfall’s leaching, the soil electrical conductivity (EC1:5) reduced by 41.7%‒79.3% for the saline water irrigation treatments. In combination with saline water irrigation, plastic film mulching can be used for sward establishment of seed propagated tall wheatgrass. However, irrigation with high salinity of drainage water enhanced the risk of plant death. Further, a pot experiment demonstrated that irrigation with 5 g L‒1 saline water led to the least reduction of forage yield and the highest crude protein content in leaves. However, the plants irrigated with ≥7 g L‒1 saline water enhanced soil salinity and reduced plant height, leaf size, and gas exchange rate. Conclusively, one irrigation with ≤5 g L‒1 saline water at the end of April or early May could be acceptable to maximize the forage yield of tall wheatgrass and minimize soil salinization risk in the coastal saline-alkaline land around the Bohai Sea.

Chronic graft-versus-host disease (cGvHD) occurs in 20-50% of recipients following allogeneic haematopoietic stem cell transplantation (allo-HSCT). Corticosteroids (CS) remain the first line treatment but have suboptimal efficacy and carry the risk of long-term side effects. New agents with a better safety profile and higher efficacy, ideally combining immunomodulatory and antifibrotic properties, are urgently needed. From 2016 to 2020, we conducted a phase 2 clinical trial with ATO in chronic GvHD (ClinicalTrials.gov ID NCT02966301 - GMED16-001). This study aimed to evaluate the efficacy and safety of a first-line combination of arsenic trioxide (ATO) and CS in adult patients with cGvHD who require systemic therapy after a first allo-HSCT for a haematological disease. In this prospective, national, multicenter, single-arm, open-label phase II study, conducted in 5 university hospital centers in France, ATO was initiated within 10 days of starting CS at 1 mg/kg/day. Patients received 11 infusions of ATO per 4-week cycle, at a dose of 0.15 mg/kg per infusion. Patients received 1 or 2 cycles of treatment depending on the clinical response and the assessment of the treating physician. The results were published in July 2022 in a paper entitled "High Response Rate and Corticosteroid Sparing with ATO-Based First-Line Therapy in Chronic Graft-versus-Host Disease after Allogeneic Hematopoietic Stem Cell Transplantation". The GMED16-001 study demonstrated convincing efficacy and safety characteristics of the intravenous drug (Trisenox^®/Arscimed^®): the first-line use of ATO in addition to corticosteroids was associated with a high clinical response rate and correlated with rapid corticosteroid (CS) sparing in moderate to severe cGvHD after allo-HSCT. We performed a post-hoc analysis of the data to determine the best schedule for treating cGvHD patients with ATO. Our post-hoc analysis leads us to the conclusion that two cycles of ATO, at 0.15 mg/kg/day, 5 days per week for 4 weeks each, separated by a 4-week therapy-free interval, appears to be the most promising treatment schedule.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

As new vaccines reduce P. falciparum (Pf) cases, clinicians can focus on rescuing more children with cerebral malaria (CM). Adjunctive “therapeutically-rational exchange transfusion” (T-REX) refers to using special “Pf-resistant” donor red blood cells (RBCs) that secrete nano-sized RBC extracellular vesicles (EVs). Can some RBC EVs rapidly dislodge Pf-infected RBCs (iRBCs) sequestered in blood vessels and reduce inflammation? Does post-exchange “rebound parasitemia” reflect sequestration-reversal? We reviewed case-reports, EV and liposome studies, expert perspectives, and time-sequence data. In the AQUAMAT study, median coma-recovery time was 20 hours for artesunate. In contrast, a CM patient treated with type-O T-REX quickly began speaking (during the procedure). For other rapid-recovery CM patients, donor RBC variables had not been specified. Despite rapid Pf-killing, drugs need 20 hours to substantially reduce iRBC cytoadhesion while EVs can selectively bind distant inflamed tissues within 15 minutes. RBCs stressed by blood-bank storage and Pf infection secrete EVs. Post-exchange “rebound parasitemia” can occur within 60 minutes and may reflect release of sequestered iRBCs. Sequestration-reversal can be assessed by monitoring Pf parasitemia and total Pf biomass. New data suggest clinicians, working with transfusion- and laboratory-medicine physicians, can, and should, assess T-REX options and publish their findings to help clarify how RBC EVs may serve as therapeutic “decoy ligands.”

Owing to the growing concerns due to dwindling fossil fuel reserves, increasing energy demand and climate emergency, it is imperative to develop and deploy sustainable energy technologies to ensure future energy supply as well as transition to the net zero world. In this context, there is great potential in the biorefinery concept for supplying drop in biofuels in the form of biodiesel. Biodiesel as a fuel can certainly bridge the gap where electrification or the use of hydrogen is not feasible, for instance heavy vehicles, farm and marine transportation sector. However, biodiesel industry also leads to formation of large amount of crude glycerol as the byproduct. Crude glycerol due to presence of several impurities may not be a suitable feedstock for all high value products derived from glycerol but fits well with glycerol esterification for producing glycerol acetins, which have numerous applications. This review critically looks at the processes using nanostructured solid/liquid acid catalysts for glycerol esterification including the economic viability of the scale up.

Energy is a fundamental ingredient in economic development and energy consumption is an index of prosperity and the standard of living. The consumption of energy has increased significantly in the last number of decades, as the standard of living has improved. Renewable energy is a sustainable and clean source of energy derived from nature. Renewable energy technology is one of the solutions, which produces energy by transforming natural resources into useful energy forms. When you do something for the first time in the world, you never attain a perfect product or solution from the start. In Central Greece Lamia city, we are the first to design and implement an off-grid energy system using hydrogen energy storage technology and phase change materials for a house residence. The action plan for energy efficiency, a series of directives and incentive mechanisms, mandatory energy certification of buildings, indicate the urgent need to reduce energy consumption in buildings, which results in a more comfortable living, long service life of buildings, which in turn preserves the environment.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

The features of a class of cubic curves with a shape factor are analyzed by means of the theory of envelope and topological mapping. The effects of the shape factor on the cubic curves are made clear. Necessary and sufficient conditions are derived for the curve to have one or two inflection points, a loop or a cusp, or to be locally or globally convex. Those conditions are completely characterized by the relative position of the edge vectors of the control polygon and the shape factor. The results are summarized in a shape diagram, which is useful when the cubic parametric curves are used for geometric modeling. Furthermore we discussed the influences of the shape factor on the shape diagram and the ability for adjusting the shape of the curve.

In patients with primary central nervous system lymphoma (PCNSL), the choice of surgical strategy for histopathologic assessment is still controversial, particularly in terms of preoperative corticosteroid (CS) therapy. To provide further evidence for clinical decision-making, we retrospectively analyzed data from 148 consecutive patients who underwent surgery at our institution. Although patients treated with corticosteroids preoperatively were significantly more likely to require a second or third biopsy (p=0.049), it was only necessary in less than 10% of the cases with preoperative corticosteroid treatment. The choice of surgical procedure did not affect diagnostic accuracy (p&gt;0.05). Preoperative CSF sampling did not provide additional information but was associated with delayed surgery (p=0.02). Surprisingly, diagnostic accuracy was significantly lower when patients were treated with anticoagulation or dual antiplatelet therapy (p=0.015). In conclusion, preoperative CS therapy can challenge the histological diagnosis of PCNSL. At the same time, our data suggest that preoperative CS treatment only presents a relative contraindication for an early surgical intervention. The standard surgical approach is stereotactic biopsy, but other approaches can be individually considered. If a definitive diagnosis cannot be made after the first surgical intervention, the timing of a repeat biopsy after discontinuation of CS remains a case-by-case decision.

We report herein high-resolution x-ray diffraction measurements of basal plane bending of homoepitaxial single-crystal diamond (SCD). The results reveal that growth parameters such as temperature, growth time and basal plane bending of the substrate affect the basal plane bending of SCD. First, the basal plane bending of SCD depends mainly on the substrate itself. The basal plane bending of SCD becomes more severe with increasing basal plane bending of the substrate and this type of basal plane bending cannot be recovered. The SCD growth experiments show that the basal plane bending increases at high temperature and with increasing growth time. Finally, to understand the mechanism behind basal plane bending, we investigate the substrate-surface temperature distribution as a function of basal plane bending of SCD fabricated by chemical vapour deposition (CVD). This allows us to propose a bending model and understand the origin of basal plane bending. The results indicate that an uneven temperature distribution on the substrate surface is the main cause of the CVD diamond base-plane bending.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

In the field of construction, materials referred to as sustainable are currently undergoing a process of technological development. This study aims to contribute to the understanding of the behavior of the fundamental properties of concretes prepared with recycled coarse aggregates that incorporate in their matrix a polyethylene terephthalate-based additive in an attempt to reduce their high porosity. Techniques to measure the gas adsorption, water porosity and x-ray diffraction (XRD) were used to evaluate the effect of the additive on the physical, mechanical and microstructural properties of these concretes. Porosity reductions of up to 30.60% are achieved with the addition of 1, 3, 4, 5, 7 and 9% of the additive, defining a new state in the behavioral model of the additive (the overdosage point) in the concrete matrix; in addition, the porous network of these concretes and their correlation whit other physical and mechanical properties are also explained.

Membrane potential generation and maintenance are fundamental parts of membrane theory. However, since its inception, theories and assumptions have remained simple, whereas the amount of knowledge available has only grown. Unfortunately, this simplification and reductionism lead to its loss of validity on both microscopic and macroscopic scales. This article shows that assumptions made outside the context of factual reality lead to contradictions that cannot be compared with science. Membrane theory must be thoroughly revised, taking into account all forgotten and unanswered assumptions and questions to conform to facts and science to maintain credibility.

Using the senses is essential to interact with objects in real-world environments. However, not all the senses are available when interacting with virtual objects in virtual environments. This paper presents a diamond methodology to fuse two technologies to represent the senses of sight and touch when interacting with a virtual object. The sense of sight is represented through augmented reality, and the sense of touch is represented through kinesthetic haptics. The diamond methodology is centered on the user experience and comprises five general stages: Experience design, Sensory representation, Development, Display, and Fusion. The first stage comes from the expected, proposed, or needed user experience. Then, each technology takes its homologous activities from the second to the fourth stage, diverging from each other along their development. Finally, the technologies converge to the fifth and final stage for fusion in the user experience. The diamond methodology was tested by generating a user's dual sensation when interacting with the elasticity of a tension virtual spring. The user can simultaneously perceive the visual and tactile change of the virtual spring during the interaction, representing the object's deformation. The experimental results demonstrated that an interactive experience can be felt and seen in augmented reality following the diamond methodology.

A mild, efficient, and photocatalytic synthesis of 6-phosphorylated phenanthridines via tandem radical addition/cyclization/aromatization of 2-isocyanobiphenyls with diarylphosphine oxides is reported. The method features operational simplicity, metal-free conditions, using low-cost rose Bengal as catalyst and sustainable air as terminal oxidant at room temperature, and providing the desired products in moderate to good yields.

Heart failure (HF) is a growing issue in developed countries and most patients present with a reduced ejection fraction. This condition significantly impairs quality of life and represents a threat not only for patients, but also for the entire healthcare system due to its high management cost. In the last decade, new medical treatments and devices have been developed to reduce HF hospitalizations and improve prognosis, while reducing the overall mortality rate. Medical therapy does not achieve the same results in all patients and, whenever it fails, technology comes in handy: novel devices for the management of HF have reduced symptoms. They have also improved the treatment of fluid retention and life threatening arrhythmias. The present review article gives to the readers a comprehensive overview of the most recent and important findings that need to be considered in HF with reduced ejection fraction patients. Both novel medical treatments and devices have been presented and discussed.

This work investigated the influence of current density, plating solution flow rate, and nozzle outlet-cathode distance on the properties of Ni-diamond composite coatings. A multi-physics field simulation is employed to analyze the interplay between current density, plating solution flow rate, and nozzle outlet-cathode distance on the flow field and electric field distribution. Additionally, particle tracing simulations were incorporated into the model to evaluate the incorporation efficiency of diamond particles during composite electrodeposition. Experimental validation of the findings shows a significant increase in the diamond particle content of the coating. This combined approach provides valuable insights for optimizing the jet electrodeposition process for Ni-diamond composite coatings with superior properties.

In this work, we demonstrate that cutting diamond crystals with a laser (532 nm wavelength, 0.5 mJ energy, 200 ns pulse duration at 15 kHz) produces a ≲20nm thick surface layer with magnetic order at room temperature. We have measured the magnetic moment with a SQUID magnetometer of six natural and six CVD diamond crystals of different size, nitrogen content and surface orientations. A robust ferromagnetic response at 300 K is observed only for crystals that were cut with the laser along the (100) surface orientation. The magnetic signals are much weaker for the (110) and negligible for the (111) orientations. We attribute the magnetic order to the disordered graphite layer produced by the laser at the diamond surface. The ferromagnetic signal vanished after chemical etching or after moderate temperature annealing. The obtained results indicate that laser treatment of diamond may pave the way to create ferromagnetic spots at its surface.

Two polyurethanes (PUs) were similarly synthesized by reacting a cycloaliphatic isocyanate with 1,4 butanediol and two polyols of different nature (polyester, polycarbonate diol) with molecular weights of 1000 Da. The PU made with polycarbonate diol polyol (YCD) was the only showing intrinsic self-healing at 20 °C. For assessing the mechanism of intrinsic self-healing of YCD, a structural characterization by molecular weights determination, infrared and X-ray photoelectronic spectroscopies, differential scanning calorimetry, X-ray diffraction, thermal gravimetric analysis and dynamic mechanical thermal analysis was carried out. It was concluded that the self-healing at 20 °C of YCD was due to non-covalent dynamic exchange interactions among the carbonate groups of the soft segments. Therefore, the chemical nature of the polyol played a key role in developing PUs with intrinsic self-healing at 20 °C.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Large office buildings are responsible for a substantial portion of energy consumption in urban districts. However, thorough assessments regarding the Nordic countries are still lacking. In this paper we analyse the largest dataset to date for a Nordic office building, by considering a case study located in Stockholm, Sweden, that is occupied by nearly a thousand employees.Distinguishing the lighting and occupants’ appliances energy use from heating and cooling, we can estimate the impact of occupancy without any schedule data. A standard frequentist analysis is compared with Bayesian inference, and the according regression formulas are listed in tables that are easy to implement into building performance simulations (BPS). Monthly as well as seasonal correlations are addressed, showing the critical importance of occupancy.A simple method, grounded on the power drain measurements aimed at generating boundary conditions for the BPS, is also introduced; it shows how, for this type of data and number of occupants, no more complexities are needed in order to obtain reliable predictions. For an average year, we overestimate the measured cumulative consumption by only 4.7%. The model can be easily generalised to a variety of datasets.

This research explores the behaviors of Generation Z consumers in China, particularly focusing on their interaction with companies through social media for the joint creation of value. Adopting a qualitative methodology, the research initially constructs a scale for assessing co-creation of value on social media platforms. Subsequently, it delves into the motivational aspects of users' engagement in these co-creative activities. The study unveils a range of utilitarian and hedonic motivations that drive Generation Z's value co-creation actions on social media. Insights derived from the findings offer both theoretical and practical implications for the field.

Membracis mexicana (Hemiptera: Membracidae) is distributed in four biogeographic provinces of Mexico, field observations indicate that there are different forms of this species but so far it has not been recorded how the different forms are and how they are distributed. The aim of this study was to quantify the phenotypic and genetic variation of M. mexicana and determine if the config-uration of biogeographic provinces impacts the distribution of this variation. To do this we ana-lyzed 307 photographs using 19 landmarks and geometric morphometrics to quantify the pheno-typic variation in helmets. We sequenced five molecular markers for 205 individuals to describe the phylogeographic pattern. As a result, we identified three morphological configurations of the helmet of M. mexicana and two genetic lineages. The morphotypes are 1) large and wide helmet with small dorsal spots, 2) small and narrow helmet with large dorsal spots, and 3) small and narrow helmet with small spots. Genetic lineages are distributed at southeast and western of Mexico. The western lineage corresponds to two helmet morphotypes (1 and 2) and the southeast lineage to morphotype 3. We found that the larger helmets correspond the western lineage and are distributed in Transmexican Volcanic Belt and Pacific lowlands provinces whereas the smallest helmets correspond to the southeast lineage and are present in Veracruzan and Yucatan Peninsula provinces.

The UNUSUAL FLORAL ORGANS (UFO) gene is an essential regulatory factor of class B genes and plays a vital role in the process of inflorescence primordial and flower primordial development. We investigated the role of UFO genes in soybean to better understand the development of floral organs through gene cloning, expression analysis, and gene knockout. In situ hybridization demonstrated predominant expression of the GmUFO1 gene in the flower primordium. Phenotypic observation of GmUFO1 knockout mutant lines (Gmufo1) showed obvious alteration in floral organ number and shape, and mosaic organ formation. In contrast, GmUFO2 knockout mutant lines (Gmufo2) showed no obvious difference in floral organs. However, the GmUFO1 and GmUFO2 double knockout lines (Gmufo1ufo2) showed a more severe mutant phenotype than the Gmufo1 lines. Gene expression analysis also showed differences in the expression of major ABC function genes in the knockout lines. Based on the phenotypic and expression analysis, our results suggest the major role of GmUFO1 in the regulation of flower organ formation in soybean and that GmUFO2 does not have any direct effect, but it might have an interaction role with GmUFO1 in the regulation of flower development. In conclusion, the present study identified UFO genes in soybean and improved our understanding of floral development that could be useful for flower design in hybrid soybean breeding.

The common dandelion uses a bundle of drag-enhancing bristles (the pappus) that enables seed dispersal over formidable distances; however, the scaling laws of aerodynamic drag underpinning pappus-mediated flight remains unresolved. In this paper, we study the aerodynamic shape of dandelion, derive the scaling law of resistance, determine the Vogel exponent. In particular, we find that the total drag coefficient is proportional to the -2/3 power of the dandelion pappus Reynolds number, and obtain the terminal velocity of the dandelion seed under gravitation field.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

The energy efficiency of existing buildings is a crucial factor in addressing Europe’s energy con-sumption challenges, accounting for nearly 40% of the total energy usage. The ongoing energy crisis, driven by the reliance on fossil fuels and increasing prices, has underscored the urgency of adopting sustainable and energy efficient practices especially to the existing building stock. Cyprus is par-ticularly vulnerable due to its heavy dependence on imported fuels for electricity generation and faces significant challenges in transforming its existing building stock into energy-efficient and sustainable structures. Extensive focus has been made by the government on the energy-efficient retrofit of non-residential public buildings. This study examines an existing cultural hall. The case study of the Cultural Hall represents the building stock before 2010 which is lacking thermal in-sulation, double glazing and any energy efficient element. It then offers an ideal case study to ex-plore sustainable solutions which can be easily adopted from the construction industry and from the building owners. The primary objective of this research is twofold: first, to develop a comprehensive retrofit plan to transform the cultural hall into a net-zero energy building; and second, to explore how this transformation can give value back to the local community. After running two simulation scenarios and providing two energy performance certificates, one with at the existing state and one with the intended retrofit measures, it is clear that the building can be a net zero energy consump-tion building. Some interesting results derived, present also how this building can provide value back to the community i.e. through solar carports for EV charging.

The main purpose of the work was to determine the powder composition and properties of iron-based sinters used as a matrix in metallic diamond tools. The FeCuSnNi sinters obtained from a mixture of commercial powders were used for research. The material was subjected to milling in a ball mill and sinter have been performed with the hot-pressing technique in a graphite mold. The physical and mechanical properties of the sinters were tested. The investigations of obtained sinters concerned density, porosity, hardness, oxygen content, static tensile test and analysis of microstructure. The static tensile test was carried out with the use of a universal testing machine UTS-100. The study of the microstructure of sinters was performed using the JSM-7100F scanning electron microscope. The sinters are characterized by a high coefficient of thermal expansion and good mechanical properties. The FeCuSnNi sinter revealed a complex phase structure. Spot chemical analysis revealed the presence of Fe solution, Cu solution and the presence of iron oxides oxides. Nickel atoms were present throughout the sinter volume. The obtained results indicate that the presented material can be used as a matrix of a diamond-metal composite in diamond tools for the processing of natural stones and building materials.

Nowadays, diamonds are widely used in science and technology. However, the properties of diamonds due to their defects are not fully understood. In addition to optical methods, positron annihilation spectroscopy (PAS) can be successfully used to study defects in diamonds. Positrons are capable of detecting vacancies, small and large clusters of vacancies induced by irradiation, by providing information about their size, concentration, and chemical environment. By mapping in the infrared (IR) range, it is possible to consider the admixture composition of the main inclusions of the whole plate. The article presents the results of the study of defects in synthetic diamond plates, one of which was irradiated by electrons. Presents data about the distribution of the defect concentration obtained by Infrared spectroscopy. PAS with a monochromatic positron beam can be used as a non-destructive technique of detecting defects (vacancy) distribution over the depth of diamond plates.

Thermobarometric calculations for mineral inclusions in diamonds provide a systematic comparison of PTXFO2 conditions for different cratons worldwide, using a database of 4440 mineral EPMA analyses. Beneath all cratons, the cold branch of the mantle geotherm (35-32 mWm−2) relates to the sub-Ca garnets and rarely omphacitic diamond inclusions, referring to major continental growth events in Archean. High-temperature plume-related geotherms are common in Proterozoic kimberlites such as Premier, Mesozoic – Roberts Victor etc. and are common in Slave and Siberian cratons. In mobile belts: Limpopo, Magondi, Ural Ural, Khapchan belts and in the marginal parts of cratons like Kimberly Australia pyroxenitic and eclogitic pyroxenes and garnets prevail. The pyropes in the mobile belts are more Fe- and Ca-rich, in central parts of cratons, the peridotitic associations with sub- Ca pyropes prevail. The accretionary complexes like Khapchan and Magondi belts a thick eclogite-pyroxenite lens is highly diamondiferous. Comparison by minerals shows that the PT estimates for clinopyroxenes and orthopyroxene from peridotites and eclogites are representing mainly the middle part of the sub-lithospheric mantle while garnets gives more high-pressure estimates. refer to eclogites and reflect the processes of the differentiation during migration of partial melts. This produces the trends of joint decreasing Mg’ and pressures. The PT for the chromites reflect conditions just above the lithosphere-asthenosphere boundary and mainly were formed due to interaction with the hydrous plume protokimberlite melts. Archean diamond inclusions from Wawa province Canada are represented by Ca-enrich pyropes giving low-temperature conditions. Inclusions from younger kimberlites in Superior and Slave (and Siberian and East European ) cratons show complex high-temperature geotherms due to plumes influence. Peridotite garnets beneath the Amazonian craton indicate complex layering in the lithosphere base and a pyroxene layer in the middle part of SCLM. Diamond inclusions from the Kimberley craton of Australia show the greatest variations in the temperatures and composition.

The shape memory alloys belong to the smart materials thanks to their thermomechanical proprieties' reply to thermal or to mechanical loading. These materials can change shape, stiffness, displacement, natural frequency, and many mechanical characteristics in response to stress or to heat such as conduction, convection or radiation. However, heating by convection or conduction are the most useful and studied methods unlike radiation. Therefore, this paper aims to study the radiation effect on the shape memory alloy behavior

The investigation of plasma channels induced by focused ultra-short 1030-nm laser pulses in bulk of synthetic HPHT diamond revealed strong dependence of their size and shape on the used numerical aperture of the lens (NA=0.15-0.45). It was shown that at loose focusing conditions, it is possible to significantly increase the length of the plasma channel with a slight increase in pulse power, while tight focusing allows to obtain more compact structures in the same range of used powers. Such dependence paves the way to new possibilities in 3D processing of transparent dielectrics, allowing, for example, to vary the spatial parameters of modified regions without changing the setup, but only by controlling the lens aperture, which seems very promising for industrial applications.

Modern building automation systems implement plenty of advanced control and monitoring functions considering various parameters like users’ activity, lighting, temperature changes etc. Moreover, new solutions based on Internet of Things and cloud services are also being developed for smart buildings to ensure comfort of use, user safety, energy efficiency improvements and integration with smart grids and smart city platforms. Such a wide spectrum of technologies and functions requires a new approach in building automation systems design to provide effective way of their implementation and flexibility during operation. At the same time, in the building design and operation industries, tools based on building information modeling and digital twins are being developed. In this paper, the authors discuss development directions and application areas of these solutions, identifying new trends and possibilities of their use in smart homes and buildings. In particular, the focus is on procedures for selecting automation functions, effective integration, and interoperability of building management systems with Internet of Things considering organization of prediction mechanisms and dynamic functional changes in buildings and smart networks. Chosen solutions and functions should consider the requirements from EN ISO 52120 standard and the guidelines defined for the Smart Readiness Indicator.

Efficient fixed crane position analysis is critical in precast buildings construction to maximize lifting efficiency for precast elements. The primary objective is to minimize the travel distances of fixed cranes, thereby enhancing operational efficiency and cost control. This involves strategically reducing the distances between the transport truck parking, where elements are stored, the fixed crane, and the construction installation point. Despite its significance, existing studies often overlook the dynamic movement efficiency of transport trucks, particularly when dealing with multiple transport trucks and various models of fixed cranes, rendering the opti-mization of this scenario a challenging NP-hard problem susceptible to combinatorial explosion. This study presents a novel mathematical model leveraging the Genetic Algorithm (GA). The model aims to solve optimal model and position of fixed cranes, along with identifying ideal positions for transport truck parking. The study's methodology is validated and demonstrated through a project case study. Comparative analyses between the proposed model and the original planning underscore a noteworthy 6% reduction in both duration and costs when lifting elements directly from transport trucks, as opposed to establishing an on-site stock yard. Furthermore, the developed GA exhibits a substantial improvement in final solutions, achieving a remarkable 30% reduction in both operational duration and costs. This research contributes valuable insights into fixed crane position analysis of precast building construction, providing foundation for enhanced operational efficiency and cost-effectiveness in the industry.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

In this paper, we present the idea of Self Supervised learning on the Shape Completion and Classification of point clouds. Most 3D shape completion pipelines utilize autoencoders to extract features from point clouds used in downstream tasks such as Classification, Segmentation, Detection, and other related applications. Our idea is to add Contrastive Learning into Auto-Encoders to learn both global and local feature representations of point clouds. We use a combination of Triplet Loss and Chamfer distance to learn global and local feature representations. To evaluate the performance of embeddings for Classification, we utilize the PointNet classifier. We also extend the number of classes to evaluate our model from 4 to 10 to show the generalization ability of learned features. Based on our results, embedding generated from the Contrastive autoencoder enhances Shape Completion and Classification performance from 84.2% to 84.9% of point clouds achieving the state-of-the-art results with 10 classes.

Beetles are by far one of the most successful and diverse insect species. A part of this success is attributed to their elytra which provide various functions such as protection to their bodies from mechanical forces and the harmful environmental factors. In this study, Stag beetle (Lucanus cervus) elytra were first examined for their overall flexural properties and were observed to have a localized shape retaining snap-through mechanism which could play a crucial role in energy absorption, e.g. during battles and falls from heights. The snap-through mechanism was validated using theoretical calculations and also finite element simulations. Elytra were also characterized to examine their puncture and wear resistance. Our results show that elytra resisted puncture up to a force of 1.8±0.4 N and have puncture resistance compared to that of commercially available puncture resistant gloves. The measured values of modulus and hardness of elytra exocuticle were 10.3±0.8 GPa and 0.7±0.1 GPa. Using the hardness to modulus ratio as an indicator of wear resistance, the estimated value was observed to be in the range of wear resistant biological materials. Thus, our study demonstrates different mechanical properties of the stag beetle elytra which can be explored to design shape retaining bio-inspired composites with enhanced puncture and wear resistance.

Packaged water consumption has grown rapidly in urban areas of many low and middle income countries, but particularly in Ghana. However, the sources of water used by this growing packaged water industry and its implications for water resource management and transport-related environmental impacts have not been described. This study aimed to assess the spatial distribution of regulated packaged water production in Ghana, both in relation to demand and for natural mineral water, to hydrogeological characteristics. 764 addresses for premises licenced to produce packaged water from 2009-2015 were mapped and compared to regional sachet water consumption and beverage import/export data examined. We find evidence to suggest packaged water is transported shorter distances in Ghana than in developed countries. For natural mineral waters, producers should be able to address the most widespread water quality hazards (including high salinity, iron and nitrates) in aquifers used for production through reverse osmosis treatment. The study suggests there is scope to integrate beverage product and groundwater regulatory databases to support groundwater management.

The treatment of the bulky Rind-based dibromosilanes, (Rind)2SiBr2 (2) [Rind = 1,1,7,7-tetra-R1-3,3,5,5-tetra-R2-s-hydrindacen-4-yl: EMind (a: R1 = Et, R2 = Me) and Eind (b: R1 = R2 = Et)], with two equivalents of tBuLi in Et2O at low temperatures resulted in the formation of blue solutions derived from the diarylsilylenes, (Rind)2Si: (3). Upon warming the solutions above −20 °C, the blue color gradually faded, accompanying the decomposition of 3 and yielding the cyclic hydrosilanes (4) via intramolecular C−H bond insertion at the Si(II) center. The molecular structures of the bulky Eind-based 3b and 4b were confirmed by X-ray crystallography. Thus, at −20 °C, blue crystals were formed (Crystal-A), which were identified as mixed crystals of 3b and 4b. Additionally, colorless crystals of 4b as a singular component were isolated (Crystal-B), whose structure was also determined by an X-ray diffraction analysis. Although the isolation of 3 was difficult due to their thermally-labile nature, their structural characteristics and electronic properties were discussed based on the experimental findings complemented by computational results. We also examined the hydrolysis of 3b to afford the silanol, (Eind)2SiH(OH) (5b).

In the present work, diamond films have been grown on GaN-on-Sapphire substrates by chemical vapor deposition (CVD) with the addition of nitrogen to the standard H2/CH4 precursor recipe. Diamond on GaN materials processing is not straight-forward, as GaN is susceptible to a quasi-pure hydrogen CVD plasma etching. 1%, 3% and 5% N2 gas was gradually added to the H2 gas with fixed 6% CH4 in the recipe to promote the growth of diamond nanocrystals. Different types of microstructures were produced, with addition of nitrogen to the precursor gas recipe. Nitrogen gas changes the diamond film microstructure from faceted to spherical grains, with signs of GaN etching. The sp3 bonded diamond film produced by nitrogen addition was found to be co-deposited along with a considerable amount of other non-diamond carbon phases (D - disordered graphite, G - crystalline graphite, TPA - trans-polyacetylene) and qualitatively all the diamond films were 50% pure (Raman peak ratio Isp3 / ID). The FWHM of the sp3 carbon Raman peak was calculated to be 6.5 cm-1, when there was no nitrogen gas in the precursor recipe, which deteriorates to a large extent after successive addition of N2. Fourier transform infrared spectroscopy (FTIR) showed a strong presence of the nitrogen related defects (peak positions at 1190 and 1299 cm-1) inside the nanocrystalline diamond (NCD) films grown with N2 addition. GaN layer etching from the base substrate by the CVD plasma was clearly evidenced by energy dispersive X-ray spectra (EDS) of the deposited films. Al elemental EDS peaks from the base sapphire substrate were observed for the films grown with nitrogen addition, but no Ga EDS peaks were detected. X-ray diffraction (XRD) micrographs further supported the enhanced GaN etching phenomenon. Nitrogen addition was thus found to be detrimental for growing CVD diamond films over GaN surfaces. The electrical resistivity of the uncoated GaN was initially measured to be 22.2 Ω-cm. However, the resistivity rose to 1.59×106 Ω-cm after the nitrogen assisted film deposition; due to the GaN etching - thereby exposing the underlying insulating sapphire substrate.

The radiation-induced optical absorption at 1.5-5.5 eV (up to the beginning of fundamental absorption) has been analyzed in CVD diamond disks exposed to 231-MeV 132Xe ions with four fluences from 1012 to 3.81013 cm-2. The 5-mm diameter samples (thickness 0.4 mm) were prepared by Diamond Materials, Freiburg (Germany), average grain size at growth site was around 80 m, the range of xenon ions was R= 11.5 m. The intensity of several bands grows with ion fluence thus confirming radiation-induced origin of the defects responsible for these bands. The recovery of radiation damage has been investigated via isochronal (stepwise) thermal annealing procedure up to 650°C, while all spectra were measured at room temperature. Based on these spectra, the annealing kinetics of several defects, in particular carbon vacancies (GR1 centers with a broad band 2 eV) and complementary C-interstitial-related defects ( 4 eV), as well as vacancies located nearby nitrogen substitutional atoms (narrow bands around 2.5 eV) have been constructed. The experimental kinetics have also been analyzed in terms of the diffusion-controlled bimolecular reactions. The migration energies of tentatively interstitial atoms (mobile components in recombination process) are obtained, their dependence on the irradiation fluences is discussed.

To achieve n-type doping in diamond, extensive investigations employing first principles have been conducted on various models of phosphorus doping and boron-phosphorus co-doping. The primary focus of this study is to comprehensively analyze the formation energy, band structure, density of states, and ionization energy of these structures. It is observed that within a diamond structure solely composed of phosphorus atoms, the formation energy of an individual carbon atom is excessively high. However, the substitution of two carbon atoms leads to the conversion of diamond into a p-type semiconductor. Upon examining the P-B co-doping structure, it is revealed that the doped impurities exhibit a tendency to form more stable cluster configurations. As the separation between the freely doped atoms and the cluster impurity structure increases, the overall stability of the structure diminishes, consequently resulting in an elevation of the ionization energy. Analysis of the electronic density of states demonstrates that the electron orbit of the B atom makes negligible contributions to the impurity levels during P-B doping.

In the last two centuries, land use change (LUC) has been the most important direct changes driver for terrestrial ecosystems. To contrast the consequent ecosystems degradation, forward-looking spatial policies and target landscape and land-use planning processes, promoting a sustainable land use change, are needed. The present paper proposes a framework of action including different landscape planning and ecological approaches: from the spatial modelling to recognize the LUC and build different scenarios, to the ecosystem services (ESs) assessment to evaluate the possible environmental impacts. Three different scenarios were built: Trend, No-Tillage and Energy crops. The Sediment Delivery Ratio and Carbon Storage and Sequestration ESs were assessed and compared for each scenario. The aim of the paper is to support decision-makers and local communities into the landscape planning process. Results show that a regional development in line with past trend could lead to further land degradation. Instead, the two scenarios proposed in compliance with EU policies, could bring benefits only if related to moderate LUCs and respecting the naturally grass-vegetated land. From the local to global scale, a guided and shared LUC management allows implementing sustainable development, basing on a deep knowledge of physical-environmental but also social and economic issues.

Hox gene collinearity (HGC) is a multiscalar property of many animal phyla particularly important in embryogenesis. It relates entities and events occurring in Hox clusters inside the chromosome DNA and in embryonic tissues. These two entities differ in linear size by more than four orders of magnitude. HGC is observed as spatial collinearity (SC) where the Hox genes are located in the order (Hox1, Hox2, Hox3 …) along the 3’ to 5’ direction of DNA in the genome and a corresponding sequence of ontogenetic units (E1, E2, E3, …) located along the Anterior – Posterior axis of the embyo. Expression of Hox1 occurs in E1. Hox2 in E2, Hox3 in E3… Besides SC, a temporal collinearity (TC) has been also observed in many vertebrates. According to TC first is Hox1 expressed in E1, later is Hox2 expressed in E2, followed by Hox3 in E3,… Lately doubt has been raised whether TC really exists. A biophysical model (BM) was formulated and tested during the last twenty years. According to BM, physical forces are created which pull the Hox genes one after the other driving them to a transcription factory domain where they are transcribed. The existing experiments support this BM description. Symmetry is a physical-mathematical property of Matter that was explored in depth by Noether who formulated a ground-breaking theory that applies to all sizes of Matter. This theory applied to Biology can explain the origin of HGC as applied not only to animals developing along the A/P axis but also to animals with circular symmetry.

The article describes a classification solution for amber stones. The problem of classifying amber is known for a long time among jewelers and artisans of amber art. Existing solutions can classify amber pieces according to color, but a need to classify by shape and texture is not satisfied up to now. The proposed solution is capable of classifying the gemstones according to a shape. Amber can be considered as a specific object since the form is difficult to define unambiguously. Data for amber experiments was gathered from amber art craftsmen. In the proposed solution amber form can be classified into 10 different classes (7 classes chosen during the experiment).

The performance of the presurgical test (preSurg) for temporal lobe epilepsy (TLE) was evaluated via video-electroencephalography (VEEG), electroencephalography (EEG), 99mTc-HmPAO single-photon emission tomography (SPECT) and 1.5 T magnetic resonance imaging (MRI) in a group of 112 men (37.0 ± 1.1 years) and 106 women (39.7 ± 1.1 years) operated on for TLE. The epileptic zone (EZ) was adequately identified to determine whether the patient reached an Engel I grade (EI) at least one year postop. Accuracy was evaluated by the coefficient α, ranging from 3 (when result = EZ) to 2 (result in the same hemisphere as the EZ), 1 (noninformative result) or 0 (EZ in the contralateral hemisphere). The simplicity of diagnosis was defined as the number of preSurg surgeries needed to identify the EZ. EI was obtained in 85.8% of patients even though 42.2% of patients had noninformative MRI results. For preSurg α was (mean ± SEM) = VEEG (2.83 ± 0.04) &gt; MRI (2.14 ± 0.08) &gt; EEG (1.87 ± 0.09) &gt; SPECT (1.71 ± 0.09). The accuracy (combination of sensitivity and specificity) was calculated as follows: VEEG (0.797) &gt; MRI (0.518) &gt; EEG (0.446) &gt; SPECT (0.360). The likelihood positive ratio was greater, and the likelihood negative ratio was lower for VEEG. The most relevant factor for the regression model was VEEG (3.106) &gt; MRI (2.558) &gt; EEG (1.905), and the factors were not significantly related to SPECT. EZs in EI patients with low simplicity were identified mainly by VEEG. A very good postoperative outcome can be obtained even in TLE patients with no lesions on MRI. The VEEG is the most reliable preSurg test and may be the only reliable test for patients with very low simplicity (i.e., difficult).single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The α(1,2)fucosyltransferase (Se enzyme) encoded by FUT2 is involved in the secretor status of ABH(O) blood group antigens. The sedel2 allele is one of the non-functional FUT2 (se) alleles in which 9.3 kb containing the entire coding region of FUT2 is deleted by Alu-mediated nonhomologous recombination. In addition to this allele, three SNPs of FUT2, c.375A>G, c.385A>T, and c.571C>T, appear to be prevalent in certain Oceanian populations such as Polynesians. Recently, we developed an endpoint genotyping assay to determine the sedel2 zygosity, using a FAM-labeled probe for detection of the sedel2 allele and a VIC-labeled probe for detection of FUT2. In this study, instead of the VIC probe, a HEX-labeled probe covering both c.375A>G and c.385A>T and a Cy5-labeled probe covering c.571C>T were added to the sedel2 allele assay mixture to allow simultaneous detection of these four variations by endpoint genotyping for the sedel2 zygosity and fluorescence melting curve analysis for c.375A>G, c.385A>T, and c.571C>T genotyping. The results obtained from 24 Samoan subjects with this method were identical to those obtained with previous methods. Therefore, it appears that present method can accurately determine these four variations simultaneously.

Digital twins are gaining in popularity for simulating complex natural and urban environments. In this context, accurate segmentation of objects within 3D urban environments is of crucial importance. The aim of this project is to develop a methodology for extracting buildings from textured 3D meshes. To this end, PicassoNet-II, a semantic segmentation architecture is employed. The methodology also incorporates Markov field-based contextual analysis to assess post-segmentation features. In addition, building instantiation is performed using cluster analysis algorithms. Training this model to fit various datasets requires a large amount of annotated data, both from Quebec City, Canada, and from simulated data. Experimental results show that the use of simulated data improves segmentation accuracy, and the DBScan algorithm proves effective in extracting isolated buildings. This project paves the way for improved applications in 3D urban modeling, offering opportunities in fields ranging from urban planning to resource management. The positive results with simulated data reinforce the impact of this research on improving digital models of our ever-changing urban environments.

This paper provides an open dataset of measured energy use, solar energy production, and building air leakage data from a 328 m² (3,531 ft²) all-electric, zero energy commercial building in Virginia, USA. Over two years of energy use data were collected at 1-hour intervals using circuit-level energy monitors. Over six years of solar energy production data were measured at 1-hour intervals by 56 microinverters. The building air leakage data was measured post-construction per ASTM-E779 Standard Test Method for Determining Air Leakage Rate by Fan Pressurization and the United States Army Corps (USACE) Building Enclosure Testing procedure; both pressurization and depressurization results are provided. The architectural and engineering (AE) documents are provided to aid researchers and practitioners in reliable modelling of building performance. The paper describes the data collection methods, cleaning, and convergence with weather data. This dataset can be employed to predict, benchmark, and calibrate operational outcomes in zero energy commercial buildings.

A series of dinuclear copper(I) N,C,N- and P,C,P-carbodiphosphorane (CDP) complexes using multidentate ligands CDP(Py)2 (1) and (CDP(CH2PPh2)2 (13) have been isolated and characterized. Detailed structural information was gained by single crystal XRD analyses of nine representative examples. The common structural motive is the central double ylidic carbon atom with its characteristic two lone-pairs involved into binding of two geminal L-Cu(I) fragments at Cu-Cu distances in the range 2.55 – 2.67 Å. In order to enhance conformational rigidity within the characteristic Cu-C-Cu triangle, two types of chelating side arms were symmetrically attached to each phosphorus atom: two 2-pyridyl functions in ligand CDP(Py)2 (1) and its dinuclear copper complexes 2-9 and 11, as well as two diphenylphosphinomethylene functions in ligand CDP(CH2PPh2)2 (13) and its di- and mononuclear complexes 14-18. Neutral complexes were typically obtained via reaction of 1 with Cu(I) species CuCl, CuI, and CuSPh or via salt elimination reaction of [(CuCl)2(CDP(Py)2] (2) with sodium carbazolate. Cationic Cu(I) complexes were prepared upon treating 1 with two equivalents of [Cu(NCMe)4]PF6, followed by the addition of either two equivalent of an aryl phosphine (PPh3, P(C6H4OMe)3) or one equivalent of a bisphosphine ligands DPEPhos, XantPhos or dppf. For the first time carbodiphosphorane CDP(CH2PPh2)2 (13) could be isolated upon treating its precursor [CH(dppm)2]Cl (12) with NaNH2 in liquid NH3. A protonated and a deprotonated derivative of ligand 13 were prepared and their coordination was compared to neutral CDP ligand 13. NMR analysis and DFT calculations reveal, that the most stable tautomer of 13 does not show a CDP (or carbone) structure in its uncoordinated base form. For most of the prepared complexes, photoluminescence upon irradiation with UV light at room temperature was observed. Quantum yields (PL) were determined to 36% for dicationic [(CuPPh3)2(CDP(Py)2)](PF6)2 (4) and to 60% for neutral [(CuSPh)2(CDP(CH2PPh2)2] (16).

In this paper, several two-dimensional clustering scenarios are given. In those scenarios, soft partitioning clustering algorithms (Fuzzy C-means (FCM) and Possibilistic c-means (PCM)) are applied. Afterward, VAT is used to investigate the clustering tendency visually, and then in order of checking cluster validation, three types of indices (e.g., PC, DI, and DBI) were used. After observing the clustering algorithms, it was evident that each of them has its limitations; however, PCM is more robust to noise than FCM as in case of FCM a noise point has to be considered as a member of any of the cluster.