Buildings are responsible for approximately 40% of global energy consumption, putting pressure on the construction industry to mitigate its environmental impact. Therefore, there is an urgent need for innovative solutions to reduce power consumption, particularly in lighting systems. The study’s primary objective was to investigate novel integrated lighting solutions that significantly reduce energy use and they explore their enhancement through Building Information Modeling (BIM) and the Internet of Things (IoT) to further improve energy efficiency and reduce the carbon footprint in buildings. Hence, this literature review aimed to examine energy-saving actions, retrofitting practices and interventions across a range of multi-use buildings worldwide over the past six years. The objective was to diagnose the goals being undertaken and ultimately validate new actions and contributions to minimise energy consumption. First, daylight harvesting and retrofitting solutions were examined in conjunction with the latest technologies, also referred to the external shadings. In consequence of this matter, comes the lack or unappropriated coordination, and so waste of energy, between daylight and electrical lighting. Secondly, how the integration of BIM facilitates the design process, providing a complete overview of all the variables of the building, thus improving indoor daylight performance and proper lighting with energy analysis. Lastly, the review addresses the role of IoT in providing real-time data from sensor networks, allowing for continuous monitoring of building conditions. This systematic literature review explores the integration of the fields to address the urgent need for innovative strategies and sustainability in the built environment. Furthermore, it thoroughly analyses the current state of the art, identifying best practices, emerging trends and concrete insight for architects, engineers, and researchers. The goal is to promote the widespread adoption of low-carbon systems and encourage collaboration among industry professionals and researchers to advance sustainable building design.

Global temperature rise due to hydrocarbon gases emission that are produced by generating the electrical power has a great attention by the researchers to reduce it till zero emission is successfully achieved. Sustainable energy source such as solar energy, wind, hydro-energy and sea wave energy are focal areas to replace the fossil fuel by clean energy. In this article, daylight is used to minimize the power consumption that required for indoor lighting using electric roller blind. Smart controller is designed to adjust the position of the roller blind stepper motor, and hence, adjust the roller blind opening, based on the preset light intensity, to achieve precise utilization of daylight inside the room. If the desired Lux is not achieved for any reason, the smart controller adjusts the LED circuit current to boost the light intensity to achieve precisely the desired Lux. Comprehensive test cases using MATLAB-Simulink is carried out to verify the performance of the proposed smart controller. Techno-economic analysis is introduced to evaluate the benefits of installing the controller. Summary and recommendation are given at the end.

This paper is an extension to previous work that introduced successful classical-control for indoor lighting system that simultaneously control LED system and roller curtain to achieve accurate light intensity for indoor lighting applications. In this paper, Multi Input Multi Output Fuzzy Logic Controller (MIMO FLC) is proposed to replace the classical-controller. Detailed method is provided to illustrate the steps to design the required MIMO FLC that has two fuzzy input, two fuzzy output and forty-five fuzzy rules with mamdani fuzzy engine. The proposed MIMO FLC is simulated in Matlab using Simulink tools. The results are illustrated, analyzed and compared with the classical-control. The response showed very close performance to the classical-controller. The maximum average error and the maximum error with respect to “Desired Lux” inside the room is -6% and -10% respectively.

The toxic cadmium (Cd) poses a serious threat to plant growth and human health. Populus euphratica CPK21 has previously been shown to attenuate Cd toxicity by reducing Cd accumulation, enhancing antioxidant defense and improving water balance in transgenic Arabidopsis. Here, we confirmed a protein-protein interaction between PeCPK21 and AtNF-YC3 by yeast two-hybrid, HaloTag pull-down and bimolecular fluorescence complementation assays. AtNF-YC3 was induced by Cd and strongly expressed in PeCPK21-overexpressed plants. Overexpression of AtNF-YC3 in Arabidopsis reduced salt inhibition of root length, fresh weight and membrane stability under Cd stress conditions (100 µM, 7 d), suggesting that AtNF-YC3 appears to contribute to the improvement of Cd stress tolerance. AtNF-YC3 improved Cd tolerance by limiting Cd uptake and accumulation, activating antioxidant enzymes, and reducing H2O2 production under Cd stress. We conclude that PeCPK21 interacts with AtNF-YC3 to limit Cd accumulation, enhance the ROS scavenging system, and thereby positively regulate plant adaptation to Cd environments. This study highlights the interaction between PeCPK21 and AtNF-YC3 under Cd stress conditions, which can be utilized to improve Cd tolerance in higher plants.

Expansins are cell wall (CW) proteins that mediate the CW loosening and regulate salt tolerance in a positive or negative way. The transcription of Populus trichocarpa expansin A6 (PtEXPA6) was downregulated upon prolonged duration of salt stress (48 h) after a transient increase induced by NaCl (100 mM). The role of PtEXPA6 in salt tolerance was determined by transferring the PtEXPA6 gene into the hybrid species Populus alba × P. tremula var. glandulosa clone 84K (84K) and Populus tremula × P. alba INRA '717-1B4' (717-1B4). The PtEXPA6-transgenic poplars of 84K and 717-1B4 showed a greater reduction in photosynthesis, stem height and diameter growth under salt stress and a reduced capacity for ROS scavenging by antioxidant enzymes, which is associated with excessive Na+ accumulation in roots and shoots. NMT flux recordings showed that the radial translocation of Na+ salt into the root xylem and real-time Na+ translocation from roots to leaves were greater in PtEXPA6-transgenic poplars than in wild-type poplars. Analysis of comparative contractility and comparative extensibility of intact root tips indicated that PtEXPA6 increased the CW loosening in the transgenic poplars of 84K and 717-1B4. Noteworthy, the PtEXPA6-promoted CW loosening was shown to facilitate radial and longitudinal transport of Na+ in transgenic poplars. We conclude that overexpression of PtEXPA6 leads to CW loosening that facilitates radial translocation of Na+ into the root xylem and subsequent Na+ translocation from roots to leaves, resulting in excessive Na+ accumulation and consequently reduced salt tolerance in transgenic poplars.

The term ‘biodynamic’ lighting is proposed as a term to capture the true aspiration of ‘life-centric’ lighting: good human and non-human outcomes for all life-sustaining behaviours on earth driven by good design for phototropism, phototaxis, photoperiodism and circadian entrainment. While future studies are necessary to consolidate this aspiration, it is clear that lighting has immediate potential to better support planetary health. As many aspects of animal, human and plantbehaviour and survival are being perturbed by widespread exposure to artificial light at night (ALAN), lighting professionals are in the middle, attempting to make design decisions that directly affect these life forms. This paper empowers readers with fundamental understandings of how light information is used by these life forms in a way crucial for development, growth and survival. The paper then provides a process for life-centric lighting design by drawing inspiration from an existing process for human-centric lighting design which can dovetail with decision-making processes that are within the workflow of lighting professionals. Holistic consideration of life-centric lighting design should look beyond altruism and romanticism by firmly rooting itself into pragmatism about long-term considerations for planetary health. Key references are consolidated and synthesized with goals of supporting knowledge translation into pragmatic lighting strategies in a manner useful for lighting professionals. While the scientific community remains sceptical about the term ‘biodynamic’ – which is argued to be developed through mysticism instead of scientific methodology – this paper counter argues that with appropriate use, the term has the potential to comprehensively capture this aspiration.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

This study demonstrates the possibility of growing green walls in normal commercial building environments with lighting designed primarily for aesthetic reasons, rather than the promotion of plant growth. Lighting is a key resource required for the growth and maintenance of robust green walls within interior environments. The study evaluated the appearance and growth of green walls with electric lighting used primarily for aesthetic reasons. Three identical green walls with six different plants were illuminated using three different white LED light sources for a period of five months. Plant health was monitored and documented in terms of growth patterns. One hundred and six subjects appraised the appearance of the walls using questionnaires. Findings of this study indicate that it is indeed possible to grow and maintain green walls in normal commercial building environments with lighting designed for aesthetic reasons. Further, it was observed that the selection of the correct plant species for the green walls is important to ensure plant health.

This paper aims to establish lighting as a key facilitator in the placemaking processes for World Heritage Sites. Placemaking is a process of designing, managing, planning and programming the development of shared public spaces within the urban fabric. Research methods inspired from ethnography such as interviews, observations and questionnaires are used to gather data from three main groups of people related to the lighting of World Heritage Sites namely: heritage experts, lighting designers, and locals and visitors. Two UNESCO designated World Heritage Sites are investigated as case studies: Saint-Avit-Sénieur in Dordogne, France and Naghshe-Jahan-Square in Isfahan, Iran. Thematic analysis of the data collected from these investigations reveal key lighting characteristics and lighting design considerations that can facilitate the placemaking process for World Heritage Sites. The lighting characteristics include: avoiding over-lighting, overly theatrical lighting and homogeneous lighting; balancing floodlighting; preventing glare; providing flexible and harmonious lighting. The lighting design considerations include: accounting meanings and values; amplifying narratives; balancing genders; building attraction and excitement; creating layers; enhancing atmospheres; ensuring safety; improving functionality; offering interpretations; and supporting activities.

GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

This study investigates the cultural dimension in sustainable lighting design to create inclusive environments. India being one of the most culturally and ethnically diverse nations in the world, with a population of almost 18% of the world population, requires attention to include cultural dimension in the design of sustainable environments. With the changing lifestyle and growth in organized retailing, the Indian retail market needs an upgrade to create inclusive environments for shared retail experiences. Lighting is among most influencing atmospheric attribute to create simulating environment for a holistic shopping experience. Preference of lighting conditions vary across the store profiles and users’ cultural background. Very little research has been carried out to understand the lighting preferences of retail customers in India. This study investigated the effects of correlated colour temperature and illuminance levels on spatial impressions and user preferences in mid-range store profile. This study involved ninety-three participants in evaluating high definition visualisations of the sixteen lighting conditions. The observations from this study emphasizes the necessity of similar studies across various states of India to identify the lighting preferences for other functional spaces and cultural backgrounds within the country. The findings may contribute towards providing recommended guidelines in lighting design and include a cultural dimension in the design of sustainable store environments.

Many farms are replacing the lighting with light emitting diode (LED) bulbs because of the technological modernization. We aimed to investigate the effects of incandescent light (IL) and LED lighting on Cobb500 broiler chickens for six weeks. Production parameters (body weight, feed consumption, feed conversion ratio), calculated slaughter values (yield%, relative breast%, thigh%) and breast meat quality parameters (pH at 45 min and 24 h postmortem, color, drip loss, kitchen equipment losses, shear force, meat composition) were recorded. Non-stop recordings were used to analyze the behavior of the birds in several periods of the rearing. LED group was significantly better in body weigh parameter between week 1-5 and feed conversion ratio between week 2-3. The most significant difference in behavior was observed in the middle of the rearing period. The chickens in the LED group spent more eating time, drinking time, interacting, and resting less. There was no difference in the meat quality parameters, only shear force was significantly lower in the LED group (1781.95±0.33 g/s vs. 2098.82±0.42 g/s). Based on our results, LED lighting can bring positive changes in animal production efficiency, behavior, and important characteristics for meat consumers.

A novel five-surface phosphor-in-glass (FS-PiG) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiG LEDs. The performance of the FS-PiG LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-glass (SS-PiG) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiG LEDs was higher than the SS-PiG LEDs for illumination, CCT, and CIE of 1.7, 7, and 23 times, respectively. Furthermore, the FS-PiG LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiG larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

In recent years, the proliferation of digital communication systems has been fueled by the increasing use of connected devices in both consumer and industrial sectors. The predominant reliance on radio frequency communication for data transfer faces challenges due to physical limitations and regulatory restrictions on frequency ranges. Responding to these challenges, Visible Light Communication (VLC) has emerged as an innovative solution, utilising the visible light spectrum to modulate the intensity of light emitted by sources like white LEDs. This paper explores the feasibility of employing Red/Green/Blue (RGB) LEDs for three-dimensional visible light communications using off-the-shelves equipment. This type of communication is known as Wavelength Division Multiplexing (WDM) as data is encoded in the three colour wavelength. On-Off Keying (OOK) is used as modulation on each wavelength. Afterwards, the more efficient Orthogonal Frequency Division Multiplexing (OFDM) modulation scheme is explored. The implemented solution involves three emission circuits, each modulating the one colour component of the RGB LED current. The reception's side involves dichroic R/G/B colour filters and a Transimpedance Amplifier (TIA) circuit, with a Raspberry Pi 4 facilitating offline data decoding sampled by an Arduino UNO. The prototype demonstrates successful VLC communication with OOK modulation at distances up to 1.5m for red and blue LEDs and 0.75m for green LEDs, achieving data rates up to 800 bit/s.

A novel five-surface phosphor-in-ceramic (FS-PiC) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiC LEDs. The performance of the FS-PiC LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-ceramic (SS-PiC) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiC LEDs was higher than the SS-PiC LEDs for illumination, CCT, and CIE of 1.1, 7, and 23 times, respectively. Furthermore, the FS-PiC LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiC larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Improper illumination of cultural heritage buildings and monuments can be a source of enormous light pollution that can have a major impact on the overall environment of the illuminated area. Such lighting can be the result of carelessness or a wrong/badly designed lighting system. This paper presents one of the methodologies that can significantly reduce light pollution, especially the spilt light out of the façade. The methodology is based on using luminaires with specially made shutters with the appropriate silhouette of the object. The shutter is planned with the help of an object photo and sizes measured at the location. The methodology was tested during the renovation of the lighting system of different churches in Slovenia and is described in the example of the Church of St. Thomas near Ptuj, Slovenia. The results showed that the methodology is effective and can significantly reduce light pollution that occurs when such buildings are incorrectly lit.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

Abstract: Peptide pools composed of short amino acid sequences have proven to be versatile tools in various research areas and clinical applications. They are powerful tools for epitope mapping, immunotherapy, and vaccine development. Their importance lies in their ability to map complex protein structures, enabling a comprehensive understanding of immune responses and facilitating the identification of potential therapeutic agents. The application of peptide pools also extends to the field of personalized medicine, offering tailored solutions for diseases such as cancer and infectious diseases. Peptide pools are complex mixtures of immunostimulatory antigens primarily intended for T-cell stimulation. They are commercially available in many different compositions and variants. However, unlike other reagents that consist of only one or a few compounds, peptide pools are highly complex products with limited stability. This makes their quality control a major challenge. Quantitative peptide analysis usually requires sophisticated methods, in most cases isotope-labeled standards and reference materials. None of these are routinely available for these products. Synthesis and purification of all labeled peptides might be required. Usually, this approach would be prohibitively laborious and expensive. Therefore, an approach is needed to provide a practical and feasible method for quality control of peptide pools. With insufficient quality control, the use of such products could lead to incorrect experimental results, which would worsen the well-known reproducibility crisis in the biomedical sciences. Here we propose the use of ultra-high performance liquid chromatography (UHPLC) with two detectors, a standard UV detector (at 214 nm) for quantitative analysis and a high-resolution mass spectrometer (HRMS) for identity confirmation. To be cost-efficient and fast, quantification and identification are performed in one chromatographic run. An optimized protocol is shown, and different peak integration methods are compared and discussed. This work was performed using a peptide pool known as CEF, which consists of 32 peptides derived from cytomegalovirus (CMV), Epstein-Barr virus (EBV) and influenza virus, ranging from 8 to 12 amino acids in length.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Color image binarization plays a pivotal role in image preprocessing work, significantly impacting subsequent tasks, particularly in text recognition. This paper concentrates on Document Image Binarization (DIB), aiming to separate a image into foreground (text) and background (non-text content). Through a thorough analysis of conventional and deep learning-based approaches, we conclude that prevailing DIB methods leverage deep learning technology. Furthermore, we explore the receptive fields pre- and post-network training to underscore the Transformer model's advantages. Subsequently, we introduce a lightweight model based on the U-Net structure, enhanced with the Mobile ViT module to better capture global information features in document images. Given its adeptness at learning both local and global features, our proposed model exhibits superior performance on two standard datasets (DIBCO2012 and DIBCO2017) compared to state-of-the-art methods. Notably, our proposed DIB method presents a straightforward end-to-end model devoid of additional image preprocessing or post-processing. Moreover, its parameter count is less than a quarter of the HIP'23 model, which achives best results on three datasets(DIBCO2012, DIBCO2017 and DIBCO2018). Finally, two sets of ablation experiments were conducted to verify the effectiveness of the proposed binarization model.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

Drowsiness is a main factor for various costly defects, even fatal accidents in areas such as construction, transportation, industry and medicine, due to the lack of monitoring vigilance in the mentioned areas. The implementation of a drowsiness detection system can greatly help to reduce the defects and accident rates by alerting individuals when they enter a drowsy state. This research proposes an Electroencephalography (EEG) based approach for detecting drowsiness. EEG signals are passed through a preprocessing chain composed of artifact removal and segmentation to ensure accurate detection followed by different feature extraction methods to extract the different features related to drowsiness. This work explores the use of various machine learning algorithms such as Support Vector Machine (SVM) the K Nearest Neighbor (KNN) the Naive Bayes (NB) the Decision Tree (DT) and the Multilayer Perceptron (MLP) to analyze EEG signals sourced from the DROZY database, carefully labeled into two distinct states of alertness (awake, and drowsy). Segmentation into 10-second intervals ensures precise detection, while a relevant feature selection layer enhances accuracy and generalizability. The proposed approach achieves high accuracy rates of 99.84% and 96.4% for intra (subject by subject) and inter (cross-subject) modes, respectively. SVM emerges as the most effective model for drowsiness detection in the intra mode, while MLP demonstrates superior accuracy in the inter mode. This research offers a promising avenue for implementing proactive drowsiness detection systems to enhance occupational safety across various industries.

UV-A (315–400 nm) is a component of solar radiation impacting plant physiology. Consequently, the impact was investigated of UV-A supplementation on various aspects of kale cultivation in a plant factory with artificial lighting. Three UV-A intensity treatments (5, 10, or 15 W/m2) were applied to kale plants for 5 days before harvesting. The results revealed that 5 or 10 W/m2 UV-A supplementation provided significant advantages for kale growth. The fresh weight of the kale shoots increased by over 35–50% after UV-A exposure. In particular, the 10 W/m2 UV-A exposure significantly improved the photosynthetic rate, water use efficiency and quantum efficiency of photosystem II (Y(II)). In addition, the treatment with UV-A positively impacted changes in leaf spectral indices, resulting in decreases in the simple ratio index (SR), the nor-malized phaeophytinization index (NPQI), and the normalized difference red edge index (NDRE). Furthermore, the phytonutrients in kale (vitamin C, soluble protein, and total phenolics) were enhanced using the 10 W/m2 UV-A treatment. One notable outcome was the consistent reduction in nitrate contents across all UV-A treatment intensities. Therefore, supplementing kale cultiva-tion with UV-A radiation was a valuable strategy for enhancing kale yield and quality in plant factory production.

This paper details the approach to the efficient design and optimization of reversible adder and multiplier utilizing Peres gates which is a three input, three output gate. Peres gates are recognized for their universality and energy efficient properties and present an intriguing option for constructing reversible circuits. Reversible logic are characterized by its ability to uniquely determine input states from output states. The design methodology involves a cascading arrangement of Peres gates each performing a reversible XOR operation on corresponding bits of the input numbers and the carry out from the preceding stage. The paper presents a detailed schematic representation, simulation results and analysis of the proposed designs of different adders and multipliers showcasing their potential for reversible applications. The integration of Peres gates in the adder and multiplier design signifies a step forward in the exploration of reversible logic circuits and their applications in contemporary computing paradigms. The overall hardware reduction is the main achievement of this research in terms of quantum cost.

The article presents the author’s works in the field of modifications and modeling of the PQC CSIDH algorithm on non-cyclic supersingular Edwards curves and its predecessor CRS scheme on ordinary non-cyclic Edwards curves are reviewed. Lower estimates of the computational speed gains of the modified algorithms over the original ones are obtained. The most significant results were obtained by choosing classes of non-cyclic Edwards curves connected as quadratic twist pairs instead of cyclic complete Edwards curves, as well as the method of algorithm randomization as an alternative to “constant time CSIDH.” It is shown that in the CSIDH and CSIKE algorithms, there are two independent cryptosystems with the possibility of parallel computation, eliminating the threat of side-channel attacks. For the CRS scheme, there are four such cryptosystems. Integral lower bound estimates of the performance gain of the modified CSIDH algorithm are obtained at 1.5 ∙ 29, and for the CRS scheme are 3 ∙ 29.

We have experimentally analyzed multi-azimuth degradation mechanisms that govern failures of commercially-available high-power (1 Watt) phosphor-coated white (hppc-W) light-emitting diodes (LEDs) covered with peanut-shaped lens under three current-stress aging (CSA) conditions. Comprehensive analyses focus on photometric, chromatic, electrical, thermal, and packaging characteristics. At the packaging level, (a) the decrease of the phosphor-conversion efficiency, (b) the yellow-browning of the optical lens, and (c) the darkening of the silver-coated reflective layer deposited with extraneous chemical elements (e.g., C, O, Si, Mg, and Cu, respectively) contribute collectively to the integral degradation of the optical power. By contrast, Ohmic contacts, thermal properties, and angles of maximum intensity remain unchanged after 3840 h aging in three cases. Particularly at the chip level, the formation of point defects increases the number of non-radiative recombination centers, and thus decreases the optical power during aging stages. Nevertheless, in view of the change of the ideality factor, the dopant activation and the annealing effect facilitate the increase of the optical power in two specific aging stages (192 h∼384 h and 768 h∼1536 h), respectively. This work offers a systematic guidance for the development of reliable LED-based light sources in general-lighting areas.

Phototherapy is an efficient strategy to respond to oxidative stress and has been in the spotlight in various therapeutic fields through its biological effect, but the exact molecular mechanism has not yet been established. As a result of irradiating RAW264.7 cells with a 630 nm or 850 nm LED with an energy intensity of 0.01J/cm2, cell viability was increased depend on the irradiation time. After H2O2 was added, 630 nm or 850 nm LEDs were irradiated for 10 min or 40 min to increase cell viability by about 1.7- or 1.6-fold, respectively. In addition, 630nm or 850nm LED irradiation showed a significant ROS scavenging effect and significantly reduced TUNEL-positive cells by 45.7% and 37.8%, respectively, compared to cells treated only with H2O2. In the result of flow cytometry, the number of cells in the late apoptosis stage was about 2.3- and 1.8-fold lower than that of the cells treated with H2O2 only, but there was no significance. The Bax/Bcl-2 ratio of cells irradiated with 630 nm or 850 nm LED was significantly lower than that of cells treated with H2O2 only, and the expression of procaspase-3 and cleaved PARP was also significantly expressed in the direction of suppressing cell death. In conclusion, the ROS scavenging activity by 630 nm or 850 nm LED irradiation, leading the expression of cell death pathway proteins in the direction of inhibiting cell death.

In areas with a deep floor plan, the distribution of natural light is not uniform. Consequently, relying solely on daylight may not suffice to meet the space's lighting requirements, necessitating the use of artificial lighting in darker areas. Therefore, a lighting system is needed that not only controls the glare near the windows but also increases the light at the end of the room and provides uniform daylight. One of the widely used systems is the “light shelf“which has three main functions: shading, increasing the depth of light penetration and reducing glare. Review articles about light shelves have been done in 2015 and 2017, while more than 80% of the studies have been carried out since 2016 and light shelves with more diverse forms and dynamic elements and many consolidations were proposed. Therefore, there is a need for a more comprehensive review. The main question of this research is how different parameters (including climate, material, ceiling and integrated systems) can help to increase the efficiency of light shelves. By using a systematic review, studies in the past three decades were classified in order to determine the effect of these parameters on improving lighting performance and controlling solar heat gain.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

Graph Neural Networks (GNNs) are powerful models capable of managing intricate connections in non-Euclidean data, such as social networks, physical systems, chemical structures, and communication networks. Despite their effectiveness, the large-scale and complex nature of graph data demands substantial computational resources and high performance during both training and inference stages, presenting significant challenges, particularly in the context of embedded systems. Recent studies on GNNs have investigated both software and hardware solutions to enhance computational efficiency. Earlier studies on Deep Neural Networks (DNNs) have indicated that methods like reconfigurable hardware and quantization are beneficial in addressing these issues. Unlike DNN research, studies on efficient computational methods for GNNs are less developed and require more exploration. This survey reviews the latest developments in quantization and FPGA-based acceleration for GNNs, showcasing the capabilities of reconfigurable systems (often FPGAs) to offer customized solutions in environments marked by significant sparsity and the necessity for dynamic load management. It also emphasizes the role of quantization in reducing both computational and memory demands through the use of fixed-point arithmetic and streamlined vector formats. This paper concentrates on low-power, resource-limited devices over general hardware accelerators and reviews research applicable to embedded systems. Additionally, it provides a detailed discussion of potential research gaps, foundational knowledge, obstacles, and prospective future directions.

This article introduces an innovative design method for public lighting systems that surpasses the limitations of conventional approaches, which rely on predefined lamp characteristics and spatial arrangement. By employing a multi-criteria decision algorithm, our study proposes an optimal design methodology considering several key aspects, including the distance between lamps, their type, power, and light distribution. The goal is to achieve optimal illumination that enhances visibility on public roads for drivers and pedestrians while simultaneously minimizing glare, installation costs and maximizing energy efficiency. The proposed methodology is implemented through an algorithm developed in Matlab, with results validated through simulations in Dialux. This information is used to construct a decision matrix, assessed using the CRITIC method across 180 different scenarios within a specific case study. The findings demonstrate the effectiveness of multi-criteria decision-making as a tool for significantly improving the planning and design of lighting in public illumination systems, allowing for selecting the optimal combination of parameters that ensure the best lighting conditions.

The increasing complexity of vehicular traffic and the prevalence of accidents, particularly rear-end collisions, necessitate enhancements in automotive safety technologies. Adilights, an innovative automotive lighting system, addresses this need by introducing a dynamic visual communication method between vehicles. This system features a novel design that employs variable-intensity brake lights configured in an upside-down "U" shape to indicate braking severity. The intensity and pattern of the lights change in response to the pressure applied to the brake pedal, providing clear and immediate feedback to following drivers. This design not only improves the perceptibility of braking signals, particularly in dense traffic and poor visibility conditions but also aims to reduce the frequency of rear-end collisions significantly. The paper details the development and testing of Adilights, discusses its integration with current vehicular systems, and evaluates its effectiveness through simulated scenarios. The introduction of Adilights marks a step forward in the use of adaptive lighting systems for enhanced vehicular communication and road safety.\cite{Lee2007RearEnd}

Response of tomato and eggplant to continuous lighting (CL) and abnormal light/dark (L/D) cycles was studied to elucidate the role of the absence of the dark period in the diurnal cycle in the development of leaf injuries under CL. Four light treatments were set: 16/8 h (control), 24/0 h (CL), 6/6 h, and 24/24 h (abnormal L/D cycles). These light treatments provided average daily light integrals of 17.3, 25.9, 13.0 and 13.0 mol m-2 day-1, respectively. Results of this work have shown that in both tomato and eggplant abnormal L/D cycles caused photoinhibition and leaf injuries similar to those in CL-grown plants. Induced defense mechanisms were not strong enough to contend against oxidative stress caused by light treatments that provided plants with even smaller DLI than 16/8 h photoperiod did. Half time during abnormal L/D cycles were dark periods. Despite these facts, abnormal L/D cycles were injurious. It is concluded that photooxidative stress induced by CL can not be attributed to excessive DLI or the continuity of light itself (the absence of dark periods). Therefore, we believe that the hypothesis suggesting circadian asynchrony to be the main triggering factor of CL-induced leaf injuries is the most plausible among many others proposed.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

Despite Low Power Wide Area Networks’ ability to offer an extended range, it might still encounter challenges with coverage blind spots in the network. This article proposes an innovative energy-efficient nature-inspired relay selection algorithm for LoRa-based LPWAN networks, serving as a solution for challenges related to poor signal range in areas with limited coverage. A behavior swarm-inspired approach has been utilized to select the relays’ localization in the network, providing network energy efficiency and radio signal extension. These relays help bridge communication gaps, significantly reducing the impact of coverage blind spots by forwarding signals from devices with poor direct connectivity with the gateway. The proposed algorithm considers critical factors for the LoRa standard, such as the Spreading Factor or device energy budget analysis. The simulation experiments validate the proposed scheme’s effectiveness in terms of energy efficiency under diverse multi-gateway topology scenarios involving thousands of devices. Specifically, it has been verified that the proposed approach outperforms the reference method in preventing the battery depletion of relays, which is vital for battery-powered IoT devices. Furthermore, for some large-scale problems, the proposed heuristic method achieves over twice the speed of the exact method with a negligible accuracy loss of less than 2%.

Private Set Intersection (PSI) is a cryptographic method in secure multi-party computation that allows entities to identify common elements in their datasets without revealing their private data. Traditional approaches assume similar-sized datasets and equal computational power, overlooking practical imbalances. In real-world applications, dataset sizes and computational capacities often vary, particularly in the Internet of Things and mobile scenarios where device limitations restrict computational types. Traditional PSI protocols are inefficient here, as computational and communication complexities correlate with the size of larger datasets. Thus, adapting PSI protocols to these imbalances is crucial. This paper explores unbalanced PSI scenarios where one party (the receiver) has a relatively small dataset and limited computational power, while the other party (the sender) has a large amount of data and strong computational capabilities. It introduces three innovative solutions for unbalanced PSI: unbalanced PSI protocol based on Cuckoo filters, unbalanced PSI protocol based on single cloud assistance, and unbalanced PSI protocol based on dual cloud assistance, each addressing the shortcomings of the previous solution. These protocols primarily optimize database computational load, storage capacity, protocol execution time, and security. Depending on performance and security needs, different protocols can be employed for applications such as private contact discovery.

Mobile Edge Computing (MEC) integrated with Wireless Power Transfer (WPT) is emerging as a promising solution to reduce task delays and extend the battery life of Mobile Devices (MDs). Cooperative user communication, or relay technology, enhances communication efficiency for users located far from the base station by mitigating the double near-far effect caused by distance. This is considered a key technology in Beyond 5G (B5G) and future communication systems. In this paper, we focus on maximizing the long-term energy efficiency (EE) of a user-cooperation WPT-MEC system, while taking into account the uncertain load dynamics at the edge MD and the time-varying state of the wireless channel. The joint optimization of wireless charging time fraction, MD offloading duration, helper node processing time, and transfer power decision presents significant challenges due to the coupling of data offloading among cooperative users and a volatile system environment. To address these challenges, we formulate the problem as a stochastic programming problem and propose an online control algorithm, DOUCA, to solve it. Our approach utilizes Dinkelbach’s method and Lyapunov optimization theory to decouple the sequential decision problem into a deterministic sub-problem for each time slot. For the sub-problem, we use variable substitution to convert the non-convex problem into a convex one, containing only a small number of variables, which can be efficiently solved. Furthermore, we provide a mathematical analysis of our algorithm’s performance. Extensive simulation results demonstrate the effectiveness of our proposed algorithm, as evidenced by an impressive energy efficiency improvement of over 20% compared to benchmark methods. Our algorithm also achieves a trade-off between EE and system stability.

This study presents a novel Fe-CNs-P/S carbon composite material, synthesized by doping elements P and S into NH2-MIL-101 (Fe) using carbonization method. The material's application in sustainable water treatment was evaluated, focusing on its effectiveness in activating persulfate for pollutant degradation. The research thoroughly investigates the synthesis process, structural characteristics, and performance in degrading pollutants. Results indicate that Fe-CNs-P/S-5 with 50% P and S co-doping is higher than that of other samples, where the degradation rate of TC in 30min is as high as 98.11% under the optimum conditions, that is temperature at 25 ℃, 0.05 g/L of catalyst concentration, and 0.2 g/L of PMS concentration. The composite material demonstrates robust versatility and stability, maintaining high degradation efficiency across multiple organic pollutants, with no significant reduction in catalytic performance after four cycles. Furthermore, the free radical quenching experiments displays that the singlet oxygen 1O2 is the main active species. It is demonstrated that the doping of P and S play a role in the enhancement of PMS activation over the Fe-CNs-P/S catalyst. This material demonstrates remarkable efficacy in treating a range of organic contaminants and exhibits excellent reusability, presenting a promising approach for enhancing sustainability in water treatment applications.

Fire is a serious security threat that can lead to casualties, property damage, and environmental damage. However, despite the availability of object detection algorithms, challenges persist in detecting fires and smoke. These challenges include slow convergence speed, poor performance in detecting small targets, and high computational cost limiting deployments. In this paper, Fire smoke and human detection based on ConvNeXt and Mixed encoder (FCM-DETR), an end-to-end object detection algorithm based on Deformable DETR, is proposed. Firstly, we introduce ConvNeXt to take the place of Resnet, which greatly reduces the amount of computation and improves the ability to extract irregular flame features. Secondly, to effectively process multi-scale features, the original encoder is decoupled into two modules. Then Mixed encoder, an innovative encoder structure, is proposed, resulting in excellent performance of multi-scale fire and smoke features fusion. What can’t be overlooked is that the encoder block is compatible with any DETR-based models. Finally, the convergence speed is accelerated and the mean of average precision is improved by applying a novel loss function called Powerful IoU v2. The experimental results indicate that our model achieves the best detection accuracy compared to other models, with mAP reaching 66.7%, mAPs and Accuracyfire achieving impressive 50.2% and 98.05%, respectively.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

We report on the design, characterization and validation of a spherical irradiation system for inactivating SARS-CoV-2, based on UV-C 275 nm LEDs. The system is designed to maximize ir-radiation intensity and uniformity, and can be used for irradiating a volume of 18 liters. To this aim: (i) several commercially available LEDs have been acquired and analyzed; (ii) a complete optical study has been carried out in order to optimize the efficacy of the system. (iii) The re-sulting prototype has been characterized optically, and tested for the inactivation of SARS-CoV-2 for different exposure times, doses and surface types. Results indicate that a 99.9% inactivation can be reached after 1 minute of treatment with a dose of 83.1 J/m2.

Unmanned aerial vehicles (UAVs) have increasingly become integral to multi-access edge computing (MEC) due to their flexibility and cost-effectiveness, especially in the B5G and 6G eras. This paper aims to enhance the Quality of Experience (QoE) in large-scale UAV-MEC networks by minimizing the shrinkage ratio through optimal decision-making in computation mode selection for each user device (UD), UAV flight trajectory, bandwidth allocation, and computing resource allocation at edge servers. However, the interdependencies among UAV trajectory, binary task offloading mode, and computing/network resource allocation across numerous IoT nodes pose significant challenges. To address these challenges, we formulate the shrinkage ratio minimization problem as a mixed-integer nonlinear programming (MINLP) problem and propose a two-tier optimization strategy. To reduce the scale of the optimization problem, we first design a low-complexity UAV partition coverage algorithm based on the Welzl method and determine the UAV flight trajectory by solving a Traveling Salesman Problem (TSP). Subsequently, we develop a coordinate descent (CD) based method and an alternating direction method of multipliers (ADMM) based method for network bandwidth and computing resource allocation in the MEC system. The CD-based method is simple to implement and has a low computational complexity, while the ADMM-based method can further enhance the optimization result through joint optimization. Extensive simulations demonstrate that our proposed algorithms perform well in large-scale edge networks and outperform other representative benchmark methods.

Fire detection is crucial for ensuring human safety and minimizing property damage. By utilizing advanced technologies, we can identify fires early, before they escalate. Autonomous fire detection systems are particularly vital in high-risk areas with minimal human presence. To address this need, we propose an automated fire-detection model based on YOLOv8. We modified the architecture of YOLOv8 and achieved impressive performances. Through comprehensive analysis of different YOLO models and their predecessors, we identified and addressed substantial gaps in this field. Also, by augmenting the framework with additional capabilities, we surpassed previous models, enabling real-time fire detection. Our proposed model achieves impressive performances, with 98% accuracy in fire detection and 97.8% in smoke detection. Moreover, recall rates for fire and smoke are 97.1% and 97.4%, respectively, with a mean average precision (mAP) accuracy of 99.1% for both cases. Finally, we applied an explainable artificial intelligence technique to interpret our proposed model and its results. This study lays the foundation for future research aimed at enhancing fire detection efficiency. The reliability of our modified model presents promising opportunities for future advancements, ensuring increased effectiveness and precision in efficient fire detection.

This study aims to quantify greenhouse gas (GHG) emissions from China's sludge treatment industry and explore the potential of novel technologies to mitigate these emissions, promoting sustainable sludge management practices. Using a life cycle assessment approach, the total GHG emissions from sludge treatment in 2017 were estimated at 18.54 Mt CO2-eq, with significant regional variations. Incineration contributed the highest emissions (1,011.53 kg CO2-eq/t dry sludge), followed by landfill (717.51 kg CO2-eq/t) and land application (276.41 kg CO2-eq/t). The uneven distribution of emissions across cities highlights the need for targeted mitigation strategies that consider local sustainability challenges. Principal component analysis revealed that economic factors and treatment scale significantly influence emissions, emphasizing the importance of integrating sustainability goals with economic development. To reduce the carbon footprint of sludge treatment and enhance sustainability, the mitigation potential and costs of various technologies were evaluated, including thermal conversion, anaerobic digestion, hydrothermal processes, and wet oxidation. These technologies offer GHG emission reductions ranging from 0.09 to 0.46 t CO2-eq/t dry solids compared to conventional methods, while also promoting resource recovery and circular economy principles. However, further optimization is necessary to enhance their environmental and economic performance, ensuring long-term sustainability. By implementing these technologies and adopting optimization strategies, China's sludge treatment industry can significantly contribute to achieving the country's carbon neutrality goal and fostering sustainable development.

Fabrication of durable materials with excellent oil adsorption capacity and separation performance for the treatment of oily wastewater is meaningful based on smart responsiveness. Herein, a solvent-responsive melamine sponge (MS) was developed via silanization followed by the in-situ growth of zeolitic imidazolate framework-8 (ZIF-8). Detailed characterization of the resultant composite MS was conducted using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The multiscale hierarchical MS substrate exhibited highly hydrophobic property in the pH range of 1-11, along with a satisfactory adsorption capacity in the range of 65.4-134.2 g/g for different oils. The modified surface transformed from superhydrophobicity/superlipophilicity to superhydrophilicity/underwater superoleophobicity upon ethanol wetting, reverting to its original superhydrophobic state upon drying. The separation flux of the MS substrate was above 1.5×104L/m2h for both oil and water removal, along with the separation efficiency more than 98.7%. No obvious changes of the separation performance after 50 successive immiscible oil/water separation indicated the excellent durability and robustness of the anchored ZIF-8 nanoparticles on the surface of modified MS substrate. More importantly, oil-in-water emulsion separation was successfully carried out via the ZIF-8 MS composite with a high separation efficiency over 99.1%. The developed smart sponge with high oil absorption capacity, excellent chemical stability and fire resistance exhibited a wide range of potential practical applications in the convenient treatment of oily wastewater.

In recent years, with the development of the Internet of Things and distributed computing, the "server-edge device" architecture has been widely deployed. This study focuses on leveraging autoencoder technology to address the binary classification problem in network intrusion detection, aiming to develop a lightweight model suitable for edge devices. Traditional intrusion detection models face two main challenges when directly ported to edge devices: inadequate computational resources to support large-scale models and the need to improve the accuracy of simpler models. To tackle these issues, this research utilizes Extreme Learning Machine for its efficient training speed and compact model size to implement autoencoders. Two improvements over the latest related work are proposed: First, to improve data purity and ultimately enhance detection performance, this study partitions the data into multiple regions based on the prediction results of these autoencoders. Second, leveraging autoencoder characteristics to investigate further the data within each region. We used the public dataset NSL-KDD to test the behavior of the proposed mechanism. The experimental results show that when dealing with multi-class attacks, the model's performance was significantly improved, the accuracy and the F1-score are improved by 3.5% and 2.9%, respectively maintaining its lightweight nature.

Energy generation now heavily relies on the field of photocatalysis. Many conventional research topics have been superseded by the conversion of solar energy into chemical or thermal energy for a variety of energy-related applications. The urgent necessity of moving away from non-renewable energy sources is a result of the problem of global warming. In an effort to create the best photocatalysts for effective solar conversion, scientists are investigating a variety of material systems and material combinations. By examining the influence of morphology changes on the photoelectrochemical activity of zinc oxide nanostructures, here electrodeposition was used to create the nanostructures. By using the proper capping agents, it is possible to control the growth rates of different ZnO facets and get well-defined nanostructures and orientation. In order to generate distinct ZnO morphologies, we report here the electrodeposition of ZnO nanostructured thin films in the presence of different capping agents. A zinc nitrate (Zn (NO₃)₂) bath was used to electrodeposit ZnO nanostructures on indium tin oxide glass (ITO) substrate at 70 °C with an applied potential of -1.0 V. Capping agents such as ethylenediamine (EDA) or ammonium fluoride (NH₄F) were added to this zinc nitrate bath. The photoelectrochemical capabilities of the morphology-controlled zinc oxide nanostructures were extensively evaluated and characterised. Thus various ZnO morphologies had an impact on the PEC properties.

Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

Facial artificial intelligence (AI) skincare applications offer patients simple and effective means of obtaining quantitative information regarding their skin characteristics. Advances in AI may facilitate dermatologic assessments by providing accurate and reliable scores for common skin concerns. The objective of our study was to assess the effect of different lighting on facial characteristic scores produced by an iPad-based AI skin analysis system. Participants were recruited from dermatology clinics. Images were captured using an AI skincare app in different lighting settings: below average lighting (L1), standard room lighting (L2), and enhanced studio lighting (L3). Raw scores produced for twenty facial characteristics were recorded. Higher raw scores indicated better skin health. Scores were compared between the three lighting conditions. Below average lighting had the highest mean raw scores for facial characteristics (79.67 ±10.56). Mean raw scores were lowest for enhanced studio lighting conditions (74.43 ±10.24). The difference in scores produced by the different lighting conditions was not statistically significant (p=0.79). Enhanced studio lighting did not appear necessary as scores were similar without the additional lighting. The application used in our study may serve as a cost-effective and convenient tool both within and outside clinical settings allowing enhanced quantitative analysis of facial characteristics.

As technology advances, people are increasingly adopting IoT (Internet of Things) devices in smart cities. These devices are equipped with sensors that are connected everywhere, from energy infrastructure and transportation to telecommunications, health and human services, waste management, public safety, and more. People want to access sensor data anytime and everywhere to make better decisions and improve their lives. To achieve this, a sensor integration model has been developed where multiple sensors are integrated under one gateway to manage and share sensor data. However, effective sharing of sensor data requires data security, privacy, confidentiality, fairness, effective architectural design, and low communication and computation costs. These issues need to be addressed in the sensor integration model in smart cities. Existing storage models face challenges in managing sensor data effectively. To overcome these issues and hurdles, a data storage framework leveraging blockchain technology has been proposed within the sensor integration model. This framework ensures data security, privacy, confidentiality, and a fair and transparent financial model, all while minimizing communication and computation costs.

Survivability is a critical concern in WSNs, heavily influenced by energy efficiency. Addressing severe energy constraints in WSNs requires solutions that meet application goals while prolonging network life. This paper presents an energy optimization approach (EOAMRCL) for WSNs, integrating the Grey Wolf Optimization (GWO) for enhanced performance. EOAMRCL aims to enhance energy efficiency by selecting the optimal duty-cycle schedule, transmission power, and routing paths. The proposed approach employs a centralized strategy using a hierarchical network architecture. During the cluster formation phase, an objective function, augmented with GWO, determines the ideal cluster heads (CHs). The routing protocol then selects routes with minimal energy consumption for data transmission to CHs, using transmission power as a metric. In the transmission phase, the MAC layer forms a duty-cycle schedule based on cross-layer routing information, enabling nodes to switch between active and sleep modes according to their network allocation vectors (NAV). This process is further optimized by an enhanced CSMA/CA mechanism, which incorporates sleep/activate modes and pairing nodes to alternate between active and sleep states. This integration reduces collisions, improves channel assessment accuracy, and lowers energy consumption, thereby enhancing overall network performance. EOAMRCL was evaluated in a MATLAB environment, demonstrating superior performance compared to EEUC, DWEHC, and CGA-GWO protocols, particularly in terms of network lifetime and energy consumption. This highlights the effectiveness of integrating GWO and the updated CSMA/CA mechanism in achieving optimal energy efficiency and network performance.

The multi-stage, multi-level assembly job shop scheduling problem (MsMlAJSP) is commonly encountered in the manufacturing of complex customized products. Ensuring production efficiency while effectively improving energy utilization is a key focus in the industry. For the energy-efficient MsMlAJSP (EEMsMlAJSP), an improved imperialist competitive algorithm based on Q-learning (IICA-QL) is proposed to minimize the maximum completion time and total energy consumption. In IICA-QL, a decoding strategy with energy-efficient triggers based on problem characteristics is designed to ensure solution quality while effectively enhancing search efficiency. Additionally, an assimilation operation with operator parameter self-adaptation based on Q-learning is devised to overcome the challenge of balancing exploration and exploitation with fixed parameters, thus the convergence and diversity of the algorithmic search is enhanced. Finally, the effectiveness of the energy-efficient strategy decoding trigger mechanism and the operator parameter self-adaptation operation based on Q-learning is demonstrated through experimental results, and the effectiveness of IICA-QL for solving EEMsMlAJSP is verified by comparing with other algorithms.

In the dynamic landscape of 6G and smart cities, Visible Light Communication (VLC) assumes critical significance for IoT (Internet of Things) applications spanning diverse sectors. The escalating demand for bandwidth and data underscores the need for innovative solutions, positioning VLC as a complementary technology within the electromagnetic spectrum. This paper focuses on the relevance of VLC in the 6G paradigm, shedding light on its applicability across smart cities and industries. The paper highlights the growing efficiency of lighting LEDs in infrastructure, facilitating the seamless integration of VLC. The study then emphasizes VLC’s robustness in outdoor settings, demonstrating effective communication up to 10 meters. This resilience positions VLC as a key player in addressing the very last meter of wireless communication, offering a seamless solution for IoT connectivity. By introducing an a freely available open-source simulator combined to an alternative waveform, UFMC, the study empowers researchers to dimension applications effectively, showcasing VLC’s potential to improve wireless communication in the evolving landscape of 6G and smart cities.

This paper proposes two max-pooling engines, named the RTB-MAXP engine and the CMB-MAXP engine, with a scalable window size parameter for FPGA-based convolutional neural network (CNN) implementation. The max-pooling operation for the CNN can be decomposed into two stages, i.e., a horizontal axis max-pooling operation and a vertical axis max-pooling operation. These two one-dimensional max-pooling operations are performed by tracking the rank of the values within the window in the RTB-MAXP engine and cascading the maximum operations of the values in CMB-MAXP engine. Both the RBM-MAXP engine and the CMB-MAXP engine were implemented using VHSIC Hardware Description Language (VHDL) and verified by simulations. They have been employed for and tested in our CNN accelerator targeting at the CNN model YOLOv4-CSP-S-Leaky for object detection.

Histones are keys to many epigenetic events and their complexes have therapeutic and diagnostic importance. The determination of the structures of histone complexes is fundamental in the design of new drugs. Computational molecular docking is widely used for the prediction of target-ligand complexes. Large, linear peptides like the tail regions of histones are challenging ligands for docking due to their large conformational flexibility, extensive hydration, and weak interactions with the shallow binding pockets of their reader proteins. Thus, fast docking methods often fail to produce complex structures of such peptide ligands at a level appropriate for drug design. To answer this challenge, and improve the structural quality of the docked complexes, post-docking refinement has been applied using various molecular dynamics (MD) approaches. However, a final consensus has not been reached on the desired MD refinement protocol. In the present study, MD refinement strategies were systematically explored on a set of problematic complexes of histone peptide ligands with relatively large errors in their docked geometries. Six protocols were compared that differ in their MD simulation parameters. In all cases, pre-MD hydration of the complex interface regions was applied to avoid the unwanted presence of empty cavities. The best-performing protocol achieved a median of 32 % improvement over the docked structures in terms of the change of root mean squared deviations from the experimental references. The influence of structural factors and explicit hydration on the performance of post-docking MD refinements was also discussed to help their implementation in future methods and applications.

Safety and the apprehension of crime persist as significant concerns in both urban and rural locales. Crime Prevention Through Environmental Design (CPTED) guidelines, an architectural approach to crime deterrence, mitigate the likelihood of criminal activity by implementing strategic defensive design plans, particularly through effective lighting schemes within urban settings, thereby alleviating fear of crime. This comprehensive set of principles serves to enhance overall quality of life. Additionally, within the realm of environmental crime prevention, enhanced street lighting has been identified as a crucial factor in diminishing both actual crime rates and the perceived risk of criminal activity in built environments. While current recommendations advocate for the installation of lighting in poorly lit areas for safety reasons, evaluating visibility solely based on the presence of existing streetlights proves insufficient for analyzing road surface luminance comprehensively. Thus, this study proposes establishing standardized illumination levels specifically tailored for facial recognition of potential criminal offenders. Furthermore, we advocate for defining specific thresholds for color temperature and colorimetric criteria to aid in distinguishing characteristics of individuals' attire. To analyze photometric safety and crime frequency in Seoul, Korea, new primary evaluation indicators were developed, including the Brightness index, Informatization index, and Safety index. By incorporating quantitative data into lighting design strategies, particularly within the framework of CPTED, there exists the potential to mitigate fear of crime during nighttime hours. These strategies facilitate the creation of well-lit environments conducive to the swift recognition and identification of potential perpetrators, thereby presenting a proactive approach to crime prevention. Consequently, this study introduces quantitative lighting standards to augment the efficacy of CPTED guidelines, ultimately contributing to the reduction of crime incidence.

Efficient gene transfer and expression tool is lacking for shrimps and shrimp cells. To solve this, this study has developed a shrimp DNA virus-mediated gene transfer and expression system, consisting of insect Sf9 cells for viral packaging, shrimp viral vector of pUC19-IHHNV-PH-GUS and baculoviral vector of Bacmid or Bacmid-VP28 encoding shrimp WSSV envelope protein VP28. The pUC19-IHHNV-PH-GUS vector was constructed by assembling the genomic DNA of shrimp infectious hypodermal and hematopoietic necrosis virus (IHHNV), which had shortened inverted terminal repeats, into pUC19 backbone, and then an expression cassette of baculoviral polyhedron (PH) promoter-driven GUS reporter gene was inserted immediately downstream of IHHNV for proof-of-concept. It was found that the viral vector of pUC19-IHHNV-PH-GUS could be successfully packaged into IHHNV-like infective virions in the Sf9 cells, and gene transfer efficiency of this system had been evaluated and verified in three systems of Sf9 cells, shrimp hemolymph cells and tissues of infected shrimps, but GUS expression could be detected only in the cases when the viral vector was co-transfected or co-infected with a baculovirus of Bacmid or Bacmid-VP28 due to the Bacmid-dependence of PH promoter. Moreover, the packaging and infection efficiencies could be significantly improved when Bacmid-VP28 was used instead of Bacmid.

This paper describes the use of an open source instrument called LANcube v2 to build a lighting device inventory. The LANcube v2 is and instrument having 5 color sensitive sensors, each on a face of a cube. The instrument can be mounted on a car roof in order to create a map of the artificial light at night while roaming the streets and roads. Based on the temporal variations of the detected signal on various cube’s faces, we developed a method of finding the position in 3D of each lighting device. The lamp spectral types can be determined thanks to the color balance of the raw Red (R) Green (G) Blue (B) and Clear (C) color bands. If one assumes a typical angular photometry of a lighting device with respect to its location, it is possible to estimate its luminous flux. Such information allows us to build a lighting devices inventory of a territory. One advantage of that new method is that it can provide information about the private lighting devices that are always excluded from public lighting inventories. We will compare the inventory extracted with that new methodology with an in situ lamp inventory made for two villages in Canada. This will allow us to emphasize the strengths and limitations of the method by comparing to the ground truth.

The object of this research is designing of new robot-to-robot communication system working in the middle of highway/roads to support mobile safety for approaching vehicles. The result of research project directs to a group of safety robot devices which induce a vehicle on a bypass route, as a vehicle guidance method using the same, and a vehicle safety guidance system. According to an embodiment of the present invention, a safety device includes a detector configured to detect a vehicle approaching the safety device, and an image projector configured to project an image onto a road surface approaching the vehicle when the detector recognizes an approach of the vehicle. It can include. According to the present invention, when it is necessary to guide the vehicle to the bypass route, the driver of the vehicle can grasp the detour route in time and move the vehicle to the next lane.

This paper highlights the problems associated with daylight use in industrial facilities. In a case study of a multi-story textile factory, we report how to evaluate daylight (as part of integral light) in the production halls marked F and G. This study follows the article in the Buildings journal, where Hall E was evaluated (unilateral daylight). These two additional halls have large areas that are 54 × 54 meters and are more than 5 meters high. The daylight is only on the side through the attached windows in envelope structures in the vertical position. In this paper, we want to present two case studies of these two production halls in a textile factory in the eastern part of Slovakia. These are halls that are illuminated by daylight from two sides through exterior peripheral walls that are against or next to each other. The results of the case studies can be applied in similar production halls illuminated by a ‘double-sided’ (bilateral) daylight system. This means that they are illuminated by natural illumination through windows on two sides in a vertical position. Such a situation is typical for multi-storied industrial buildings. The proposed approximate calculation method for the daylight factor can be used to predict the daylight in similar spaces in other similar buildings.

In this study, we evaluated chlorophyll fluorescence (CF) under two extreme illumination conditions at plant scale with a passive spectroradiometer. Fluorescence (F) was estimated by reading directly from radiance spectra of a variety of plants illuminated with light-emitting diode (LED) grow lights in the laboratory. Solar-induced fluorescence (SIF) was estimated from spectral measurements of the same plants under sunlight using the Fraunhofer Line Depth (FLD) method. Chlorophyll fluorescence yield (F_yield) and solar-induced fluorescence yield (SIF_yield) were calculated by normalizing F and SIF with absorbed photosynthetically active radiation (APAR). Two approaches to estimating APAR were compared: utilizing white reference spectra and reflected spectra versus white reference spectra combined with the fraction of absorbed photosynthetically active radiation (fPAR) derived from literature. Average F and SIF were different by a factor of approximately twenty-four (F = 0.110 ± 0.038 Wm⁻²μm⁻¹sr⁻¹ versus SIF = 2.60 ± 1.87 Wm⁻²μm⁻¹sr⁻¹). In contrast, the average normalized values F_yield and SIF_yield were within the margin of error of one another (F_yield = 0.022 ± 0.008 μm⁻¹sr⁻¹ and SIF_yield = 0.030 ± 0.020 μm⁻¹sr⁻¹). This study highlights the influence of APAR on CF and the importance of properly accounting for it when estimating yield and demonstrates the ability of two simple and portable experimental setups with a passive instrument to obtain fluorescence metrics.

A Co–doped porous carbon was successfully fabricated by a facile carbonizing procedure using coal hydrogasification semi-coke (SC) as the carbon and cobalt nitrate as the magnetic precursors, respectively. The microwave absorption (MA) performances were regulated by adjusting the mass ratio of the precursors. The dielectric loss from the carbon framework, the magnetic loss from nano–sized Co particles coupled with multiple scattering from the residual pores synergistically contribute to the favorable MA capabilities. When the initial mass ratio of cobalt nitrate and SC was 1:1, the Co/C composite showed the lowest reflection loss of -33.45 dB at the thickness of 4.0 mm. The effective absorbing bandwidth (EAB) could achieve 3.5 GHz at 2 mm in thickness. This work not only exploits a new avenue for the structural design and facile fabrication of dielectric and magnetic loss combinations, but also opens up another way for the high value–added utilization of SC.

In the Internet of Things (IoT) era, Mobile Edge Computing (MEC) significantly enhances the efficiency of smart devices but is limited by battery life issues. Wireless Power Transfer (WPT) addresses this issue by providing a stable energy supply. However, effectively managing overall energy consumption remains a critical and under-addressed aspect for ensuring the network’s sustainable operation and growth. In this paper, we consider a WPT-MEC network wit user cooperation to migrate the double near-far effect for the mobile node (MD) far from the base station. We formulate the problem of maximizing long-term computation rates under a power consumption constraint as a multi-stage stochastic optimization (MSSO) problem. This approach is tailored for a sustainable WPT-MEC network, considering the dynamic and varying MEC network environment, including randomness in task arrivals and fluctuating channels. We introduce a virtual queue to transform the time-average energy constraint into a queue stability problem. Using the Lyapunov optimization technique, we decouple the stochastic optimization problem into a deterministic problem for each time slot, which can be further transformed into a convex problem and solved efficiently. Our proposed algorithm works efficiently online without requiring further system information. Rigorous mathematical analysis shows that our algorithm achieves O(1/V),O(V) trade-off between computation rate and queues stability. Extensive simulation results demonstrate that our proposed algorithm outperforms baseline schemes, achieving approximately 4% enhancement while maintain the queues stability.

In this study, multi-layer ceramic capacitors (MLCCs) detached from lighting sector's waste electrical-electronic equipment (WEEE) are characterised for the presence of rare earth elements (REEs) and precious metals (PMs). Their digestion was carried out with HNO3 & aqua regia on a heating plate and characterised with the use of inductively coupled plasma optical emission spectroscopy (ICP-OES) & scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX). The contents of REEs and PMs are 0.84 wt% and 0.60 wt%, respectively, and create an economic stored value in MLCCs that is essentially defined by PMs of 98.67% and by Pd 78.37%. The content of the main elements is: Nd 0.366 wt%, Y 0.220 wt%, Dy 0.131 wt%, Ag 0.467 wt%, and Pd 0.105 wt%. The results confirm the need of selective removal and separate recycling process of MLCCs from WEEE drivers.

Gravity forward modeling as a basic tool has been wildly used to topography correction and 3D density inversion. The source region is usually discretized into tesseroid (i.e., spherical prism) to consider the influence of the curvature of planets in global or large-scale problems. Traditional gravity forward modeling methods in spherical coordinates, including the Taylor expansion and Gaussian-Legendre quadrature, are all based on spatial domain, which are mostly low computational efficiency. This study proposes a high-efficient forward modeling method of gravitational fields in spherical harmonic domain, in which the gravity anomalies and gradient tensors can be expressed as spherical harmonic synthesis form of spherical harmonic coefficients of 3D density distribution. A homogeneous spherical shell model has been used to test its effectiveness compared with traditional spatial domain methods. It demonstrates that the computational efficiency of the proposed spherical harmonic domain method has improved by four orders of magnitude and with a similar level of computational accuracy compared with the optimized 3D GLQ method. Finally, the proposed forward method is applied to topography correction of the Moon. The results show that the gravity response of the topography by our method is close to that of the optimized 3D GLQ method, and is also consistent with previous results.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

With the rapid growth of large language models (LLMs), there is increasing demand for memory and computation in LLMs. Recent efforts on post-training pruning of LLMs aim to reduce the model size and computation requirements, yet the performance is still sub-optimal. In this paper, we present a plug-and-play solution for post-training pruning of LLMs. The proposed solution has two innovative components: 1) Relative Importance and Activations (RIA), a new pruning metric that jointly considers the weight and activations efficiently on LLMs; and 2) Channel Permutation, a new approach to maximally preserve important weights under N:M sparsity. The two proposed components can be readily combined to further enhance the N:M semi-structured pruning of LLMs. Our empirical experiments show that RIA alone can already surpass all existing post-training pruning methods on prevalent LLMs, e.g., LLaMA ranging from 7B to 65B. Furthermore, N:M semi-structured pruning with channel permutation can even outperform the original LLaMA2-70B on zero-shot tasks, together with practical speed-up on specific hardware. Our code is available at: https://github.com/biomedical-cybernetics/Relative-importance-and-activation-pruning

Major factors affecting in vitro immature embryo rescue efficiencies from Prunus persica or P. armeniaca accessions, have been identified along with improving its economic feasibility. Three culture media, based on Woody Plant Medium (WPM) have been used depending on the embryo size. Embryos less than 5-mm-long were cultured in WPM supplemented with 1 mM BAP and 1 mM GA3, while embryos bigger than 5-mm-long were cultured in hormone-free medium, with or without vermiculite. Environmental in vitro culture conditions consisted of three phases, a (I) stratification at 4 C during a 3 to 5-month-long period in the dark, followed by (II) growth of germinated embryos at 14 C for 4-week-long period, with 12h light a day, which favors plantlet development, and finally (III) growth at 24 C, with 16h light a day, until the plantlets were moved to the greenhouse for acclimatization. Germination of smaller embryos, at the end of the phase I, ranged from 82.2% to 22.1%, for apricot and flat peaches, respectively, whereas for bigger embryos the germination varied from 97.4% to 53.2% for the same type of fruits. Embryo germination for peaches and nectarines ranged from 40.1% to 30.3% for smaller embryos, and from 91.9% to 64.0% for bigger embryos. Endo- and exophytic contamination, affecting from 7.4% to 52.9% of cultured embryos depending on the fruit type and conservation conditions, and the capacity to acclimate to soil conditions, ranging from 50.4% to 93.2%, were the two most important factors influencing protocol’s efficiency and economic feasibility. Considering the overall efficiencies, expressed as hardened plants transferred to field plots over clean uncontaminated embryo, values ranged from 55.8% for nectarines, 54.0% for peaches, 45.6% for apricot, and 23.3% for flat fruits. Addition of vermiculite to the culture medium significantly improved plantlet development, avoiding subculture to fresh medium when an extension of the phase III was required before acclimatization. Compared to laboratory glassware, use of food glass containers with air-permeable sealing film, along with vermiculite-containing medium significantly reduced costs, when handling the large number of embryos required for breeding programs.

High electricity demand for consumption at current supply level in Indonesia led to the rising cost of electricity bills. This factor is compounded by the fact that many electric generators in Indonesia still use fossil fuels, which contributes to the high basic generation cost. UBL is one of the universities that aim to be a green campus. Our research explores the possibility of installing motion sensor to contribute on the energy efficiency. Although mostly common in developed countries, the use of motion sensor for energy efficiency is still rare, especially in Indonesia. despite rising cost and supply shortages, Indonesian buildings are still of high energy consumption. our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. One of the efforts to lower energy demand in consumer side is to use the electricity efficiently, such as turning off lights in a room when it's not in use. This method can be simply done by turning the light switches for office and classrooms, but difficult to do in public spaces such as toilets and corridors. Our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. Automatic light switches experimentally installed in sample toilet room prove that electricity consumption from the lamps can contribute to the reduction of total weekly energy that translates into Green House Gas emission reduction.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.

Salidroside, a valuable phenylethanoid glycoside, is obtained from plants belonging to the Rhodiola genus, known for its diverse biological properties. At present, salidroside is still far from large-scale industrial production due to the lower titer and higher process cost. In this study, we constructed a biosynthetic pathway from L-tyrosine to salidroside in Saccharomyces cerevisiae. To increase sali-droside production, we for the first time constructed an in vivo UDP-glucose regeneration system that sucrose synthase GmSUS worked in conjunction with UDP-glucose transferase RrUGT33 to improve the UDP-glucose availability with inexpensive sucrose as the consumed substrate. Finally, the molar conversion rate of L-tyrosine could reach 95%. To further reduce the cost, co-culture with E. coli that synthesized L-tyrosine de novo resulted in an 81% reduction in the final substrate cost per 1 kg of salidroside compared to the initial cost. The final titer of salidroside obtained 3.8 g/L and was the highest titer achieved at the Shake-Flask-Level in the existing reports. And this marked the first successful synthesis of salidroside in an in situ enhanced UDP-glucose system using sucrose. This accomplishment laid a robust groundwork for further investigations into the synthesis of other notable glycosides and natural compounds.

This article explores the efficiency of various clustering methods for image segmentation under different luminosity conditions. Image segmentation plays a crucial role in computer vision appli-cations, and clustering algorithms are commonly used for this purpose. The search for an adaptive clustering mechanism aims to ensure maximum symmetry of real objects with objects/segments in their digital representations. However, clustering methods performance can fluctuate with varying lighting conditions during image capture. Therefore, we assess the performance of several clustering algorithms — including k-means, K-Medoids, fuzzy c-means, Possibilistic C-Means, Gus-tafson-Kessel, Entropy-based Fuzzy, Riddler-Calvard, Kohonen Self-Organizing Maps, and Meanshift — across images captured under different illumination conditions. Additionally, we develop an adaptive image segmentation system utilizing empirical data. Conducted experiments highlight varied performance among clustering methods under different luminosity conditions. This research enhance better understanding of luminosity's impact on image segmentation and aiding in method selection for diverse lighting scenarios.

Obstructive Sleep Apnea (OSA) surgery is now a viable solution in selected patients and the “remodelling” palatopharyngeal surgery is the most common one. Recently it becomes less in-vasive with the introduction of Barbed Sutures (BS). An optimization of surgical technique is represented by Barbed pharyngoplasty (BP), that requires surgical precision and needs efficient and precise oropharyngeal visualization. Consequently, the lighting system is of pivotal im-portance in BP. The aim of this work is to describe the first experience on the use of a new light-ing system, called KlaroTM in BP for OSA. We evaluated the Klaro™ system in 15 consecutives BP for OSA in comparison with conventional headlamp illumination. The visualization of pala-topharyngeal muscle in the bottom of the tonsillar fossa, entry and exit needle, such as needle tip were statistically better with KlaroTM than headlamp illumination both for surgeon and resi-dent (p<0.05). No significant differences for the visualization of the posterior pharyngeal wall and uvula were reported. The KlaroTM lighting system allows a satisfied illumination of oral cavity and oropharynx in the majority of cases. We encourage to use of KlaroTM not only in BP for OSA, but also in all oral and pharyngeal surgeries, including tonsillectomy and oncological surgery.

We present observations from evaluation of internal environmental quality of industrial halls with priority on daylighting in combination with the integral lighting. The physical parameters related to indoor lighting in large industrial halls in winter and summer periods were analyzed using in situ measurements and computational methods. These are part of a comprehensive research on indoor environmental quality of industrial halls with the aims of saving energy and providing a comfortable environment for the workers while improving the productivity. The results showed that the procedures used for evaluation of residential or office buildings may not be used for industrial buildings. We also observed that the criteria of occupants’ comforts for indoor industrial buildings may differ from those of other kinds of buildings. Based on these results, an adequate attention is required for designing the industrial buildings. For this reason, appropriate evaluation methods and criteria should be created. We found the measured values of daylight factor very close to the skylight component of the total illumination. The skylight component was observed on average 30% that of the measured daylight factor values. Although the daylight is not emphasized when designing the industrial buildings and its contribution is small, but it is very important for the workers psychology and physiology. The workers must feel a connection with the exterior environment; otherwise, their productivity decreases.

In the context of intelligent and integrative lighting, in addition to the need for color quality and brightness, the non-visual effect is essential. This refers to the retinal ganglion cells (ipRGCs) and their function, first proposed in 1927. The melanopsin action spectrum has been published in CIE S 026/E: 2018 with the corresponding melanopic equivalent daylight (D65) illuminance (mEDI), melanopic daylight (D65) efficacy ratio (mDER) and 4 other parameters. Due to the importance of mEDI and mDER, this work synthesizes a simple computational model of mDER as the main research objective, based on a database of 4214 practical spectral power distributions (SPDs) of daylight, conventional, LED, and mixed light sources. In addition to the high correlation coefficient R2 of 0.96795 and the 97% confidence offset of 0.0067802, the feasibility of the mDER model in intelligent and integrated lighting applications has been extensively tested and validated. The uncertainty between the mEDI calculated directly from the spectra and that obtained by processing the RGB sensor and applying the mDER model has reached ± 3.3% after an appropriate matrixing process and proper illumination characterization combined with the successful mDER calculation model. This result opens the potential of low-cost RGB sensors for applications in intelligent and integrative lighting systems to optimize and compensate the non-visual effective parameter mEDI using daylight and artificial light in indoor spaces. The goal of the research on RGB sensors and the corresponding processing method are also presented and their feasibility is methodically demonstrated. A comprehensive investigation with a huge amount of color sensor sensitivities is necessary in a future work of other researches.

Vehicle HVAC systems can accumulate and recirculate highly infectious respiratory diseases via aerosols. Integrating UVC to complement automobile HVAC systems can protect occupants from developing allergies, experiencing inflammatory problems, or acquiring respiratory infectious diseases by inactivating pathogenic organisms. UVC can add little to no static pressure with minimal space, unlike mercury lamps which are larger and heavier. Additionally, UVC LEDs are effective at low voltage and have no mercury or glass. While previous experiments have shown UVC LED technology can reduce bacteriophage Phi6 concentrations by 1 log in 5 minutes (selected as the average time to clean the cabin air), those studies had not positioned LED within the HVAC itself or studied the susceptibility of the surrogate at the specific wavelength. This study aimed to assess the disinfection performance of UVC LEDs in automotive HVAC systems and determine the dose-response curve for bacteriophage Phi6, a SARS-CoV-2 surrogate. To achieve this, UVC LEDs were installed in a car HVAC system. To determine inactivation efficacy, a model chamber of 3.5 m3, replicating the typical volume of a car, containing the modified automobile HVAC system was filled with bacteriophage Phi6, and the HVAC was turned on with and without the UVC LEDs being turned on. The results revealed that HVAC complemented with UVC reduced bacteriophage Phi6 levels significantly more than the HVAC alone and reduced the viral concentration in the cabin by more than 1 LRV (90% viral reduction) in less than 5 minutes. The performance after 5 minutes is expected to be significantly better against SARS-CoV-2 because of its higher sensitivity to UVC, especially at lower wavelengths (below 270 nm). HVAC alone could not achieve a 90% viral reduction of bacteriophage Phi6 in 15 minutes. Applying UVC LEDs inside an HVAC system is an effective means of quickly reducing the number of aerosolized viral particles in the chamber, by inactivating microorganisms leading to improved cabin air quality.

High efficacy LED lamps combined with adaptive lighting control and greenhouse integrated photovoltaics (PV) could enable the concept of year-round cultivation and become a feasible option even in the harsh climate of the Nordic countries. Meteorological satellite data of this region was analyzed in a parametric study to evaluate the potential of these technologies. The generated maps showed monthly average temperatures fluctuating from -20°C to 20°C throughout the year. The natural photoperiod and light intensity also changed drastically, resulting in monthly average daily light integral (DLI) levels ranging from 45-50 mol·m-2·d-1 in summer and contrasting with 0-5 mol·m-2·d-1 during winter. To compensate, growth room cultivation independent from outdoor conditions could be used in winter. Depending on the efficacy of the lamps, the electricity required for sole-source lighting at 300 µmol·m-2·s-1 for 16 hours would be between 1.4 and 2.4 kWh·m-2·d-1. Greenhouses with supplementary lighting could help start the cultivation earlier in spring and extend it further into autumn. The energy required for lighting highly depends on several factors such as the natural light transmittance, the light threshold settings and the lighting control protocol, resulting in electric demands between 0.6 and 2.4 kWh·m-2·d-1. Integrating PV on the roof or wall structures of the greenhouse could offset some of this electricity, with specific energy yields ranging from 400 to 1120 kWh·kWp-2·yr-1 depending on the region and system design.

The Double Diaphragm Forming (DDF) process uses vacuum pressure and heat to pre-shape composite reinforcements between flexible diaphragms. Accurate modelling of heat transfer within DDF requires knowledge of the thermophysical properties of the constituent materials. This study investigates the specific heat and thermal conductivity of silicone diaphragms, carbon fibers (chopped and powdered), thermoplastic veils, and their combinations. Experiments measured the specific heat of each material using differential scanning calorimetry and the thermal conductivity of silicone and carbon fabric preforms using the transient plane source method and modified transient plane source method respectively. The influence of reheating cycles on specific heat of carbon fiber-veil samples and the effect of compaction on thermal conductivity of silicone and carbon fabrics were explored. While silicone exhibited linear specific heat behavior, the thermoplastic veil showed non-linearity due to phase change. The combined carbon fiber-veil samples demonstrated slight non-linear specific heat variations depending on reheating cycles. Thermal conductivity of the fabric preforms decreased with the addition of thermoplastic veil and under vacuum-compaction conditions. The established temperature-dependent property relationships provide valuable data for optimizing DDF preforming parameters and enhancing energy efficiency in composite manufacturing.

Outdoor lighting design is a multidisciplinary topic that involves, among other aspects, design, energy savings, protection of nocturnal biodiversity and profitability, all of which are important functional and regulatory requirements. However, they do not necessarily consider user needs, which make perception and emotional response difficult parameters in the lighting design process. The studies carried out on lighting and its impact on emotions have mainly been done indoors. The objective of this work is to propose a methodology to evaluate emotional response to the illuminated nocturnal urban space with the purpose of providing knowledge to create emotionally efficient luminous spaces that improve people's perception and well-being. The instrument used was the survey (online questionnaires), based on Kansei engineering, created to incorporate the emotional variable in product design. The research was carried out with participants from Peru, Spain, and Germany. The results collected the reaction of the participants to different types of night-time luminous spaces presented, which contributes to a better understanding of user needs and activities regarding the space. This knowledge is intended to help designers meet their expectations.

Genetic transformation is a critical tool for gene manipulation and functional analyses in plants, enabling the exploration of key phenotypes and agronomic traits at the genetic level. While dicotyledonous plants offer various tissues for in vitro culture and transformation, monocotyledonous plants, such as rice, have limited options. This study presents an efficient method for genetically transforming rice (Oryza sativa L.) using seed-derived embryogenic calli as explants. Two target genes were utilized to assess regeneration efficiency: green fluorescent protein (eGFP) and the apple FLOWERING LOCUS T (FT)-like gene (MdFT1). Antisense MdFT1 was cloned into a vector controlled by the rice α-amylase 3D (Ramy3D) promoter, while eGFP was fused to Cas9 under the Ubi promoter. These vectors were introduced separately into rice embryogenic calli from two Korean cultivars using Agrobacterium-mediated transformation. Transgenic seedlings were successfully regenerated via hygromycin selection using an in vitro cultivation system. PCR confirmed stable transgene integration in the transgenic calli and their progeny. Fluorescence microscopy revealed eGFP expression, and antisense MdFT1-expressing lines exhibited notable phenotypic changes, including variations in plant height and grain quality. This study demonstrated the effective use of seed-derived embryogenic calli for rice transformation, offering a promising approach for developing transgenic plants in monocot species.

Modular inversion on large operands is a time-consuming calculation used in elliptic curve cryptography. Its hardware implementation requires extensive hardware resources such as lookup tables and registers. We investigate state-of-the-art modular inversion algorithms and evaluate the performance and cost of the algorithms and their hardware implementations. We then propose a high-radix modular inversion algorithm aimed at short execution time and low hardware cost. We present a detailed radix-8 hardware implementation based on 256-bit primes in Verilog HDL and compare its cost performance with other implementations. Our implementation on the Altera Cyclone V FPGA chip uses 1227 ALMs (Adaptive logic modules) and 1037 registers. The modular inversion calculation takes 3.67 microseconds. The AT (Area time) factor is 8.30, outperforming other implementations. We also present an implementation of elliptic curve cryptography using the proposed radix-8 modular inversion algorithm. The implementation results also show that our modular inversion algorithm is more efficient in area time than other algorithms.

Conventional fluorescent lamps used in tissue culture are costly light sources showing excessive wavelength emission-bandwidth that must be replaced by alternative, less costly and much lower power-consuming energy sources. The use of Light-Emitting Diodes (LEDs) is the best option due to their potential role as elicitors of secondary metabolite production in many plant models. Gynura procumbens(G. procumbens) is widely used for treating various diseases. Here, leaf explants were cultivated in MS medium supplemented with 0.5 mg/L of NAA and 2.0 mg/L of BAP for 30 days under white, blue, and red LEDs. Secondary metabolites were analyzed by HPLC and LC-MS. Blue LEDs elicited the highest antioxidant activity, total flavonoid, and phenolic content. Furthermore, the content of cyanidin-monoglucosides increased significantly increased under blue light.

Extracting entities from large volumes of chicken epidemic texts is crucial for knowledge sharing, integration, and application. However, Named Entity Recognition (NER) encounters significant challenges in this domain, particularly due to the prevalence of nested entities and domain-specific named entities, coupled with a scarcity of labeled data. To address these challenges, we compiled a corpus from 50 books on chicken diseases, covering 28 different disease types. Utilizing this corpus, we developed a nested NER model, MFGFF-BiLSTM-EGP. This model integrates the Multiple Fine-Grained Feature Fusion (MFGFF) module with a BiLSTM neural network and employs an Efficient Global Pointer (EGP) for predicts the entity location encoding. In MFGFF module we designed three encoders, character encoder, word encoder and sentence encoder, this design effectively captures fine-grained features and improves the recognition accuracy of nested entities. Experimental results show that the model performs robustly, with F1 scores of 91.98%, 73.32%, and 82.54% on the CDNER, CMeEE V2, and CLUENER datasets, respectively, outperforming other commonly used NER models. Specifically, on the CDNER dataset, the model achieved an F1 score of 79.68% for nested entity recognition. This research not only advances the development of knowledge graph and intelligent question-answering system for chicken diseases but also provides a viable solution for extracting disease information that can be applied to other livestock species.

This study introduces a sophisticated neural network structure for segmenting breast tumors. It achieves this by combining a pretrained Vision Transformer (ViT) model with a U-Net framework. The U-Net architecture, commonly employed for biomedical image segmentation, is further enhanced with Depthwise Separable Convolutional Blocks to decrease computational complexity and parameter count, resulting in better efficiency and less overfitting. The Vision Transformer, renowned for its robust feature extraction capabilities utilizing self-attention processes, efficiently captures the overall context within images, surpassing the performance of conventional convolutional networks. By using a pretrained ViT as the encoder in our U-Net model, we take advantage of its extensive feature representations acquired from extensive datasets, resulting in a major enhancement in the model’s ability to generalize and train efficiently. The suggested model has exceptional performance in segmenting breast cancers from medical images, highlighting the advantages of integrating transformer-based encoders with efficient U-Net topologies. This hybrid methodology emphasizes the capabilities of transformers in the field of medical image processing and establishes a new standard for accuracy and efficiency in activities related to tumor segmentation.

Lead-acid batteries utilised in electrical substations release hydrogen and oxygen when these are charged. These gases could be dangerous and cause a risk of fire if they are not properly ventilated. Therefore, this research seeks to design and implement a network control panel for heating, ventilation, and air-conditioning systems (HVACS). This is done using a specific range of controllers, which have more than thirty loops of proportional, integral and derivative (PID) control to achieve a cost-effective design. It performs the required function of extracting hydrogen, oxygen, and maintaining the desired temperature of the battery storage room within the recommended limits (i.e. 25°C ±1°C tolerance) without compromising quality as set out in the user requirement specification in Appendix-A. The system control panel allows the user to access control parameters such as changing temperature set-points, fan-speed, sensor database amongst others. The hardware is configured to detect extreme hydrogen and oxygen gas content in the battery room and ensure that the HVACS extract the gas content to the outside environment. The results of the system show that the network control panel effectively operates as per the recommended system requirements. Therefore, the effective operation of the HVACS ensures sufficient gas ventilation, thus mitigating the risk of fire in a typical battery storage room. Furthermore, the effective operation of HVACS enhances battery lifespan because of regulated operating temperature, which is conducive to minimise the effect of sulfation in lead acid Batteries (LABs).

The current study investigated the impacts of light quality and different levels of fertility on mineral nutrient concentrations in shoot and root tissues of Chinese kale (Brassica oleracea var. alboglabra). ‘Green Lance’ Chinese kale were grown under: 1) fluorescent/incandescent light; 2) 10% blue (447 ± 5 nm) / 90% red (627 ± 5 nm) LED light; 3) 20% blue / 80% red LED light; and 4) 40% blue / 60% red LED light as sole-source lighting at two different levels of fertility. All plants were harvested 30 d after seeding, and shoot and root tissues were analyzed for mineral nutrients. Lighting and fertility interacted to influence kale shoot and root mineral nutrient concentrations. Results indicate sole-source LED lighting used in production can impact mineral nutritional values of baby leafy greens now popular for the packaged market.

Cloud data centers play a vital role in modern computing infrastructure, offering scalable resources for diverse applications. However, managing costs and resources efficiently in these centers has become a crucial concern due to the exponential growth of cloud computing. User applications exhibit complex behavior, leading to fluctuations in system performance and increased power usage. To tackle these obstacles, we propose the consolidation of virtual machines (VMs) to optimize resource utilization and reduce operational costs. This paper introduces a novel algorithm, leveraging the Modified Artificial Feeding Birds Algorithm (ModAFBA), to manage cost optimally in cloud data centers by reducing power usage while meeting service level agreements (SLAs). The ModAFBA algorithm, inspired by bird foraging behavior, dynamically adjusts solutions based on environmental changes. Comprehensive experimental evaluation demonstrates the superiority of the proposed algorithm in terms of power usage, migration count, and SLA compliance. Through this research, we aim to advance cost management and resource optimization in cloud data centers, providing a valuable tool for cloud service providers to enhance infrastructure efficiency and achieve cost savings.

In this work, zinc oxide (ZnO)/ granular activated carbon (GAC) composites at different ZnO concentration (0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC) were prepared by an in-situ hydrothermal method and demonstrated synergistic photocatalytic degradation and ad-sorption of Rhodamine B (RhB). The thermal stability, morphological structure, elemental com-position, crystallographic structure, and textural properties of developed catalysts were charac-terized by thermal gravimetric analysis (TGA/DTG), scanning electron microscopy equipped with energy dispersive-x-ray (SEM-EDS), x-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) analysis. Successful loading of ZnO onto GAC was confirmed by SEM-EDS and XRD analysis. The BET surface areas of GAC, 0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC were 474 m2/g, 450 m2/g, 453 m2/g, and 421 m2/g, respectively. The decrease in GAC could be attributed to the successful loading of ZnO on the GAC surface. Notably, 0.5M-ZnO@GAC exhibited the best photocatalytic degradation efficiency of 82% and 97% under UV-A and UV-C light over 120 min, attributed to improved crystallinity and visible light absorption. The photocatalytic degradation parameters revealed that lowering the RhB concentration, raising the catalyst dosage and pH be-yond the point of zero charge (PZC) would favor the RhB degradation. Photocatalytic reusability was demonstrated over 5 cycles. Scavenger tests revealed that the hydroxyl radicals (•OH), su-peroxide radicals (O2−•), and photoinduced hole (h+) radicals play a major role during the RhB degradation process. Based on the TOC results, the RhB mineralization efficiency of 79.1% was achieved by 0.5M-ZnO@GAC. Additionally, GAC exhibited a strong adsorptive performance towards RhB with adsorption capacity and RhB removal of 487.1 mg/g and 99.5% achieved within 90 min equilibrium time. The adsorption characteristics were best described by pseu-do-second-order kinetics, suggesting chemical adsorption. This research offers a new strategy for the development of effective photocatalyst materials with potential for wider wastewater treat-ment applications.

In this work, we report the synthesis of a new thiosemicarbazone-based drug of N'-(di(pyridin-2-yl)methylene)-4-(thiazol-2-yl)piperazine-1-carbothiohydrazide (HL) featuring a thiazole spectator for the efficient coordination with Cu(II) to give [CuCl(L)]2 (1) and [Cu(NO3)(L)]2 (2). Both 1 and 2 exhibit dimeric structures ascribed to the presence of di-2-pyridylketone moieties that demonstrate dual functions of chelation and intermolecular bridging. HL, 1 and 2 are highly toxic against hepatocellular carcinoma cell lines Hep-G2, PLC/PRF/5, and HuH-7, with half maximal inhibitory concentration (IC50) values as low as 3.26 nmol/mL (HL), 2.18 nmol/mL (1), and 2.54 × 10−5 nmol/mL (2) for PLC/PRF/5. While the free ligand HL may elicit its anticancer effect via sequestration of bio-relevant metal ions (i.e. Fe3+ and Cu2+), 1 and 2 are also capable of generating cytotoxic reactive oxygen species (ROS) to inhibit cancer cell proliferation. Our preliminary pharmacokinetic studies revealed that oral administration (per os, PO) of HL has a significantly longer half-life t1/2 of 21.61 ± 9.4 h, nearly doubled as compared to that of the intravenous (i.v.) administration of 11.88 ± 1.66 h, certifying HL as an effective chemotherapeutic drug via PO administration.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

Pseudolysimachion nakaianum (Ohwi) T.Yamaz. is an endemic species that is an important species in the forest ecosystems of South Korea. This study aimed to develop an in vitro propagation system for P. nakaianum, to enhance the availability of this rare and endemic plant for commercial horticulture and restoration efforts. We utilized cotyledon explants from in vitro germinated seeds and two types of explants (petiole and leaf) from in vitro seedlings to assess the impact of five different cytokinins on adventitious shoot organogenesis in P. nakaianum. The half-strength Murashige and Skoog (MS) medium, supplemented with 10 µM thidiazuron (TDZ) for both cotyledon and petiole explants, yielded the highest shoot induction rates (61.1 ± 9.6% and 26.7 ± 8.8%, respectively) and the greatest number of shoots (3 ± 0.6 and 4.4 ± 0.5, respectively). Responses from leaf explants were variable, with none showing in vitro regeneration. Successfully acclimatized P. nakaianum plantlets in a greenhouse demonstrated normal growth. This protocol outlines an effective method for the direct in vitro regeneration from cotyledon and petiole explants of P. nakaianum, providing valuable information for the conservation of this species.

Determining the estrous cycle stages in mice is essential for optimizing breeding strategies, synchronizing experimental time lines, and facilitating studies in behavior, drug testing, and genetics. It is critical for reducing the production of genetically unmodified offspring in the generation and investigation of genetically modified animal models. An accurate detection of the estrus cycle is particularly relevant in the context of the 3Rs—Replacement, Reduction and Refinement. The estrous cycle, encompassing the reproductive phases of mice, is key to refining experimental designs and addressing ethical issues related to the use of animals in research. This study presents results from two independent laboratories on the efficacy of the Mouse Estrus Detector (MED) from Elmi Ltd. (Latvia) for the accurate determination of the estrus phase. The female mice of five strains/stocks (CD1, FVB/N, C57Bl6/J, B6D2F1, and Swiss) were used. The results showed that the MEDProTM is a low -traumatic, simple, rapid and painless method of estrus detection that supports the principles of the 3Rs. The use of the MEDProTM for estrus detection in mice caused minimal stress, enhanced mating efficiency, facilitated an increase in the number of embryos for the in vitro fertilization and allowed the production of the desired number of foster animals.

A machine learning method for classifying Lung UltraSound is here proposed to pro- vide a point of care tool for supporting a safe, fast and accurate diagnosis, that can also be useful during a pandemic like as SARS-CoV-2. Given the advantages (e.g. safety, rapidity, portability, cost-effectiveness) provided by the ultrasound technology over other methods (e.g. X-ray, computer tomography, magnetic resonance imaging), our method was validated on the largest LUS public dataset. Focusing on both accuracy and efficiency, our solution is based on an efficient adaptive ensembling of two EfficientNet-b0 models reaching 100% of accuracy, which, to our knowledge, outperforms the previous state-of-the-art. The complexity of this solution keeps the number of parameters in the same order as an EfficientNet-b0 by adopting specific design choices that are adaptive ensembling with a combination layer, ensembling performed on the deep features, minimal ensemble only two weak models. Moreover, a visual analysis of the saliency maps on sample images of all the classes of the dataset reveals where the focus is on an inaccurate weak model versus an accurate model.

An event occurring within a stationary environment, in the direction toward which an observer self-rotates, is perceived to precede a simultaneous event, in the direction away from which she moves. When self-rotation results from angular acceleration in the dark, perception of space is also distorted, such that the subjective straight-ahead shifts in the opposite direction to motion and temporal event promotion. A reference frameshift theory, based on the special theory of relativity, is proposed to explain these findings. Here, a hyperbolic tangent transformation of objective angular velocity constrains subjective self-rotation velocity within finite bounds, consistent with it being a limited perceptual resource. Identifying this subjective variable with vestibular nystagmus slow-phase angular velocity, the asymptotic perceived self-rotation velocity is estimated at ~200 °⁄s. When included in the Lorentz transformations of the new formalism, this value predicts experimental simultaneity distortion. Hypothetically, the hyperbolic tangent objective-to-subjective transfer function would maximize the differential entropy of the percept, and thereby also the stimulus/percept mutual information, if angular velocities of body rotation encountered in naturalistic environmental interaction have a logistic probability density distribution of scale 100 °⁄s, a proposed experimental test of the scheme.

The second article in the series presents the application of the Smoothed Particle Hydrodynamics (SPH) method to modelling of batch crystallisation in stirred tanks. A methodology to integrate the population balance equations (PBE) in parallel and independently from the Navier-Stokes equations is demonstrated. The benefits of the proposed methodology in terms of computational requirements, accuracy and availability of the crystal size distribution are discussed. The specific formulation of the SPH equations where the resulting system of ordinary differential equations is solved using the weighted contributions rather than numerically by solving a linear system of equations allows for massive parallelisation and a very loose coupling of the population balance and the fluid dynamics. It has been demonstrated, that the population balance equations can be solved on a Shared Memory Architecture (SMA) system using the OpenMP interface while the fluid dynamics equations being computed independently on a General Purpose Graphics Processing Unit (GPGPU) using the NVidia CUDA technology. This way, a significant portion of the computational overhead due to the large number of additional transport equations resulting from the discretisation of the population balance was removed: the SPH simulation coupled with 200 population balance equations was only 40% slower compared to SPH-only simulation. Two methods for the solution of population balance equations that preserve full crystal size distribution were implemented: discretised population balance (DPB) and method of characteristics (MOCH). The DPB equations are solved using the high-resolution finite-volume method with flux limiter and the effect of a large number of different flux limiters have been investigated. Both methods were validated using the case studies from the literature where an analytical solution can be derived. The developed models were applied to a numerical solution of coupled computational fluid dynamics and population balance equations to model a batch crystallization process. The effect of the hydrodynamics on the local temperature/supersaturation and the resulting crystal size distribution was captured and compared to the ideal mixing case. The simulation results from the DPB and MOCH methods were compared in terms of computational requirements and accuracy and MOCH selected as computationally more efficient and accurate.

A typical orchard's mechanical operation consists of three or four stages: lining, digging for plantation, moving the seedling from nurseries to the farm, moving the seedling to the planting hole, and planting the seedling in the hole. However, the digging the planting hole is the most time-consuming operation. In fruit orchards, robots' usage is increasingly becoming more prevalent to increase operational efficiency. They offer practical and effective services to both industry and people, whether they are assigned to plant trees, reduce the use of chemical fertilizers, or carry heavy loads to relieve staff. Robots can operate for extended periods of time and can highly adept at repetitive tasks like planting many trees. The present study aims to identify the locations for planting trees in orchards using geographic information systems (GIS), to develop an autonomous drilling machine and use the developed robot to open planting holes. There isn't a comparable study on autonomous hole planting in the literature in this regard. The agricultural mobile robot is a four wheeled nonholonomic robot with differential steering and forwarding capability to stable target positions. The designed mobile robot can be used in fully autonomous, partially autonomous, or fully manual modes. The drilling system, which is a y-axis shifter driven by a DC motor with reducer includes an auger with a 2.1 HP gasoline engine. SOLIDWORKS software was used for designing and drawing of the mobile robot and drilling system. The Microsoft Visual Basic.NET programming language was used to create the robot navigation system and drilling mechanism software. The cross-track error (XTE), which determines the distances between the actual and desired holes positions, was utilized to analyze the steering accuracy of the mobile robot to the drilling spots. Consequently, the average of the arithmetic means was determined to be 4.35 cm, and the standard deviation was 1.73 cm. This figure indicates that the suggested system is effective for drilling plant holes in orchards.

Transitioning to clean cooking fuels is not only part of achieving SDG7, but also makes a significant contribution to mitigating climate change by reducing carbon emissions. The paper contradicts the conventional wisdom that electricity is too expensive to cook with. The paper explores the energy required to cook dishes using different technologies and fuels by analysing data from Cooking Diaries and Controlled Cooking tests conducted under the MECS programme. Electric pressure cookers (EPCs) use least energy when compared with electric hotplates, and a detailed description of how the EPC works explains why this should be. The paper draws out distinctions between African and Asian dishes, notably the impact of energy intensive dishes prepared mostly in Africa. Standard efficiency based approaches to comparing the performance of stoves are not appropriate to modern electric cooking devices so an alternative approach based on specific energy consumptions is proposed e.g. charcoal stoves use 15 times as much energy as EPCs to cook African dishes. Energy ratios provide a basis for estimating carbon emission reductions associated with transitioning to modern cooking fuels. Historical costs show that the cost of cooking with an EPC can be only 20% of the cost of cooking with charcoal, which highlights the potential for modern, energy efficient electric cooking devices to defy the conventional wisdom of the energy ladder.

This paper provides a review of an emerging field in the food processing sector, referring to efficient and safe food supply chains, ’from farm to fork’, as enabled by Artificial Intelligence (AI). Recent advances in machine and deep learning are used for effective food production, energy management and food labeling. Appropriate deep neural architectures are adopted and used for this purpose, including Fully Convolutional Networks, Long Short-Term Memories and Recurrent Neural Networks, Auto-Encoders and Attention mechanisms, Latent Variable extraction and clustering, as well as Domain Adaptation. Three experimental studies are presented, illustrating the ability of these AI methodologies to produce state-of-the-art performance in the whole food supply chain. In particular, these concern: (i) predicting plant growth and tomato yield in greenhouses, thus matching food production to market needs and reducing food waste or food unavailability; (ii) optimizing energy consumption across large networks of food retail refrigeration systems, through optimal selection of systems that can get shut-down and through prediction of the respective food de-freezing times, during peaks of power demand load; (iii) optical recognition and verification of food consumption expiry date in automatic inspection of retail packaged food, thus ensuring safety of food and people’s health.