With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Evapotranspiration is a critical component of the hydrological cycle, and it has a decisive impact on the ecosystem balance in arid and semi-arid regions. The Yinchuan Plain, located in the Gobi of Northwest China, has a strong surface ET. In order to assess the ET pattern in this region, we obtained the ETa of Yinchuan Plain between 1987 and 2020 using the GEE platform. We employed the Surface Energy Balance Model (SEBAL), specifically geeSEBAL, to analyze the change pattern of ET over different seasons, years, and land types. The results show that: ① In spring, the daily ETa of the Yinchuan Plain is highest in the central lake wetland area, with a maximum value of 4.32 mm day-1. In summer, it is concentrated around the croplands and water bodies, with a maximum value of 6.90 mm day-1; In Autumn and winter, it is mainly concentrated around the water bodies and impervious areas, with maximum values of 3.93 and 1.56 mm day-1, respectively. ② From 1987 to 2020, the ET of the Yinchuan Plain showed an obvious upward and downward trend in some areas with significant land use changes, but the overall ET of the region remained relatively stable without dramatic fluctuations. ③ The evapotranspiration of different underlying land use types in the Yinchuan Plain region is as follows: water body>cultivated land>impervious>grassland>bare land. Our results showed that geeSEBAL is highly applicable in the Yinchuan Plain area. It allows for the accurate and detailed inversion of ET in the study area, which facilitates the study of regional hydrological cycle and water governance.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

In the context of constructing new power systems, distribution networks are increasingly incorporating distributed resources such as distributed photovoltaic (PV) systems, decentralized wind turbines (WT), and new types of energy storage system (ESS), which may lead to prominent issues such as voltage overruns and reverse heavy overloads in the distribution network. While distributed resources are valuable for voltage regulation, their regulation characteristics vary with their operation means, and the randomness and volatility of renewable power generation will also influence the optimization and regulation of voltage in the distribution network. This paper proposes a multi-time scale reactive power optimization and regulation method for distribution networks in a multi-source interactive environment. Firstly, the voltage regulation characteristics of distributed PV systems, decentralized ES, and distributed WT are analyzed. Based on this analysis, then a multi-time scale voltage optimization scheme for distribution networks using MPC method is proposed, which optimizes the voltage regulation strategies for each distributed resource in a rolling manner. Furthermore, an event-triggered real-time voltage zoning control strategy based on voltage sensitivity is proposed to address the real-time sudden voltage overlimit problems. The modified IEEE 33-node system is used to verify the performance of proposed method, simulation results indicate that the issue of voltage overruns at distribution network nodes has been improved, and the intraday rolling optimization yields results that are more realistic compared to the day-ahead optimization method.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

In order to serve the online monitoring of the aging state of high-voltage (HV) cables, a novel method based on impedance spectroscopy has been proposed. Firstly, the method uses the Debye model to restore the dielectric response of the insulating material from the mechanism. Secondly, based on the transmission line equation, a calculation model for the impedance spectroscopy of HV cables was established. Then, the characteristics of the impedance spectroscopy under different overall aging and local deterioration states were analyzed. Further, the simulation analysis of the influence of factors such as load factor, length, metal resistivity, and geometric parameters on the impedance spectroscopy was carried out. Finally, diagnostic criteria were proposed, which are divided into two major categories: known cable parameters and unknown cable parameters. If the geometric parameters are known, the aging state can be determined using the resonance peak values and the resonance peak frequencies. If the geometric parameters are unknown, it is necessary to test the impedance spectroscopy in the healthy condition of the cable as the baseline curve. By comparing the impedance spectroscopy of the cable under test with the baseline curve, the aging development trend of the cable can also be determined.

With the global objectives of achieving a ‘carbon peak’ and ‘carbon neutrality’, along with the implementation of carbon reduction policies, China’s industrial structure has undergone significant adjustments, resulting in constraints on high-energy consumption and high-emission industries while promoting the rapid growth of green industries. Consequently, these changes have led to an increasingly complex power system structure and presented new challenges for electricity demand forecasting. To address this issue, this study proposes a 24-step multivariate time series short-term load forecasting algorithm model based on KNN data imputation and BiTCN bidirectional temporal convolutional networks combined with BiGRU bidirectional gated recurrent units and attention mechanism. The Kepler adaptive optimization algorithm (KOA) is employed for hyperparameter optimization to effectively enhance prediction accuracy. Furthermore, using real load data from a wind farm in Xinjiang as an example, this paper predicts the electricity load from January 1st to December 30th in 2019. Experimental results demonstrate that our comprehensive short-term load forecasting model exhibits lower prediction errors and superior performance compared to traditional methods, thus holding great value for practical applications.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

The lack of defect image data is one of the main factors affecting the accuracy of supervised deep learning-based defect detection models. In response to the insufficient training data of defect images with complex backgrounds such as rust and surface oil leakage in substation equipment, leading to poor performance of the detection model, this paper proposed a novel adversarial deep learning model for substation defect generation: ADD-GAN. In comparison to existing generative adversarial networks, this model generates defect images based on effectively segmented local areas of substation equipment images, avoiding image distortion caused by global style changes. Additionally, the model utilizes a joint discriminator for overall image and defect image to address the issue of low attention to local defect areas, thereby improving the loss of image features. This enhances the overall quality of generated images as well as locally generated defect images, ultimately improving image realism. Experimental results demonstrate that the YOLOV7 object detection model trained on the dataset generated using the ADD-GAN method achieves an mAP of 81.5% on the test dataset, representing an improvement of 9.6% over the original dataset, 5.7% over traditional augmentation methods, and 7% over typical adversarial deep learning methods. This confirms that the ADD-GAN method can generate a high-fidelity dataset of substation equipment defects.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Bearing fault diagnosis is crucial for ensuring the stable operation of mechanical equipment. With the continuous development of deep learning technology, Convolutional Neural Networks (CNNs) have demonstrated significant advantages in the field of fault diagnosis. This paper proposes a new method that combines various CNN architectures to improve the accuracy of bearing fault diagnosis. We designed five different convolutional network structures, including SerConv, ResConv, One-Shot Aggregation Convolution (OSAConv), Cross-Stage Aggregation Convolution (CSAConv), and MD-DAConv. Experimental results on the Case Western Reserve University (CWRU) bearing dataset show that the proposed method exhibits high accuracy and robustness in fault diagnosis. The results indicate that strategies such as multi-directional, multi-scale, and residual connections play a crucial role in enhancing the depth and breadth of feature extraction, while simple and effective feature fusion and information transmission mechanisms are key to ensuring the robustness and generalization ability of the model.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

The volatility and uncertainty associated with the high proportion of wind and PV output in the new power system significantly impact power and energy balance, making it challenging to accurately assess the risks related to renewable energy abandonment and supply guarante. Therefore, a probabilistic power and energy balance risk analysis method based on distributed robust optimization is proposed. Firstly, the affine factor and the flexible ramp reserve capacity of thermal power are combined to establish a probabilistic index, which serves to characterize the risk associated with power and energy balance. Drawing upon the principles of conditional value at risk theory, the risk indexes of load shedding power and curtailment power under a certain confidence probability are proposed. Secondly, the probability distribution fuzzy sets of uncertain variables are constructed using the distributionally robust method to measure the Wasserstein distance between different probability distributions. Finally, aiming at minimizing the operation cost of thermal power, the risk cost of power abandonment and the risk cost of load shedding, a distributed robust optimal scheduling model based on flexible ramp reserve of thermal power is established.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

Induction motors are the most numerous and significant dynamic loads in power systems. In transient voltage stability analysis, dynamic equivalent models are commonly used to simplify the representation of a group of induction motors. This paper presents an method for the grouping and aggregation of induction motors at a common bus. Firstly, grouping rules were provided for clustering induction motors into several subgroups based on the mechanical principles of rotor force and motion, and Aggregation Rules were provided for aggregating a motor subgroup into a single-unit model based on the relationship between voltage drop and power transmission in distribution networks. Secondly, guided by the grouping rules, high-speed remaining electromagnetic torque and low-speed remaining electromagnetic torque were defined as new clustering indicators, and an adaptive K-means clustering method using silhouette coefficient verification was provided to obtain the optimal motor subgroups. Thirdly, guided by the Aggregation Rules, a dynamic equivalent method was further provided to obtain the equivalent single-unit model from a motor subgroup. Lastly, a transient voltage stability simulation in a typical distribution network was presented to illustrate that the proposed clustering and equivalent methods are more reasonable, accurate, and effective than traditional methods, as the obtained model has better dynamic characteristics and can more accurately reproduce the process of voltage collapse.

We describe a forecast system based on the Weather Research and Forecasting (WRF) model for the prediction of high-impact weather events affecting power utilities, particularly conditions conducive to wildfires. The system was developed for Pacific Gas and Electric Corporation (PG&E) to operationally forecast conditions in Northern and Central California. It was established in 2014 and has been periodically improved. In the current configuration, WRF forecasts are routinely performed multiple times each day on a 2-km grid, and the results are used as input to wildfire fuel moisture, fire probability, and wildfire spread models. Components of the system include a stochastically perturbed ensemble; an annually updated reanalysis covering more than 30 years; and validation against PG&E’s extensive mesonet and other observing networks. We describe the development and validation of the next operational edition. Configurations tested include irrigation triggered by crop growing season and an ensemble-based approach with intelligently sub-selected Global Ensemble Forecast System (GEFS) members. The latter approach allows for enhanced uncertainty sampling in WRF forecasts and can greatly improve WRF forecasts when calibrated by observations.

(1) Background: We aim to construct a machine learning (ML) algorithm to predict the risk of distant metastasis (DM) of T1 and T2gallbladder cancer (GBC); (2) Demographic and clinical pathological data of T1 and T2 GBC patients were extracted from the National Institutes of Health (NIH)’s Surveillance, Epidemiology, and End Results (SEER) database between 2004 and 2015 to develop seven ML algorithm models. Models were evaluated based on accuracy, precision, recall rate, F1- score, and area under the receiver operating characteristic curve (AUC); (3) Results:A total of 4371 patients were included in the study, of whom 764 (17.4%) developed DM. Multivariate logistic regression showed that age, histology, tumor size, T and N stages were independent factors in GBC with DM. A novel nomogram was established to predict distant metastasis in early T stage GBC patients. Evaluation indicators of the best model Random Forest (RF) were as follows: accuracy (0.828), recall rate (0.862), precision (0.811), F1- score (0.836), and AUC value (0.913); (4) Con-clusions: The RF model constructed in this study could accurately predict distant metastasis in GBC patients, which may provide clinicians with more personalized clinical decision-making recom-mendations.

The zinc oxide (ZnO) arrester is positioned on locomotive roof preventing other onboard electrical equipment from the harm caused by external and internal overvoltages. A number of locomotive arrester burnout and explosion accidents occur during traction supply network harmonic resonance causing train stoppages and power outages in the network. This study firstly carries out high-frequency tests to investigate the wide frequency band electrical characteristics of the locomotive arrester, explaining that the arrester is prone to fault during resonance. Consequently, a prognostics and health management (PHM) for locomotive arrester is proposed providing on online monitoring, fault warning and health assessment solutions, which is beneficial to the operation and maintenance of arresters in the future. The testing method and PHM scheme presented in this paper can be not only applied to the arrester, also readily expanded to other high-voltage electrical equipment on the electric locomotive.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

The contamination of soils by mineral oils presents a significant environmental challenge, particularly due to the widespread use of petroleum products in various industrial sectors. This study investigates the efficiency of microwave heating compared to conventional resistance heating for the thermal desorption of mineral oil from contaminated soils. Experimental results demonstrated that microwave heating offers superior performance in terms of pollutant removal efficiency, energy consumption, and preservation of soil's physical and chemical properties. The study further conducted a kinetic analysis of the desorption process, revealing that microwave heating follows a first-order kinetic model and requires lower activation energy than conventional methods. The findings suggest that microwave-assisted thermal desorption is a highly effective and energy-efficient technology for soil remediation, providing a potential alternative to conventional techniques. This research offers valuable insights into optimizing thermal desorption processes for environmental remediation, with implications for broader applications in soil treatment.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

This paper addresses the evolving landscape of electricity markets in Europe, with a focus on the integration of Renewable Energy Communities as introduced by the Renewable Energy Directive 2018/2001. Residents within a postal code area are highly incentivized to join a community, which enables them to exchange energy among themselves at lower procurement costs. Thereby, energy management systems optimize the operation of respective energy systems, with electrical load forecasting playing a key role. Given that prosumers may switch between communities on a daily basis, electricity demands within these groups will vary, leading to data that is non-stationary, discontinuous as well as non-identical and independently distributed. To encounter this issue, we propose a sophisticated forecasting model that applies federated learning, using informations from various distributed communities to learn domain-invariant features. To achieve this, we initially utilize synthetic electrical load time series at district level and aggregate them to profiles of Renewable Energy Communities with dynamic portfolios. Subsequently, we develop a forecasting model that accounts for the composition of residents of a Renewable Energy Community, adapt data pre-processing in accordance with the time series process, and detail a federated learning algorithm that incorporates weight averaging and data sharing. Following the training of various experimental setups, we ultimately evaluate their effectiveness. The findings suggest that our proposed framework is capable of effectively forecast non-stationary and discontinuous time series and that it can be applied to new, unseen data through the integration of knowledge from multiple sources.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

Accurate and prompt determination of fire types is essential for effective firefighting and reducing damages. However, traditional methods such as smoke detection, visual analysis, and wireless signals pose unavailability in identifying fire types. This paper introduces FireSonic, an acoustic sensing system that leverages commercial speakers and microphones to actively probe the fire using acoustic signals, effectively identifying indoor fire types. By incorporating beamforming technology, FireSonic first enhances signal clarity and reliability, thus mitigating signal attenuation and distortion. To establish a reliable correlation between fire types and sound propagation, FireSonic quantifies the Heat Release Rate (HRR) of flames by analyzing the relationship between fire heated areas and sound wave propagation delays. Furthermore, the system extracts spatiotemporal features related to fire from channel measurements. Experimental results demonstrate that FireSonic attains an average fire type classification accuracy of 95.5% and a detection latency of less than 400 ms, satisfying the requirements for real-time monitoring. This system significantly enhances the formulation of targeted firefighting strategies, boosting fire response effectiveness and public safety.

Electric tractors have many advantages, including high torque, excellent controllability, energy efficiency, simple structure, and electric interface for expansion. However, a significant limitation lies in their endurance. This study presents the design of an extended-range power supply system to ensure continuous endurance of electric tractor. The objective is to provide a continuous power source for our self-developed electric tractor while preserving the benefits of electric propulsion. Extended-range power systems utilize a primary mover, typically an oil-fueled internal combustion engine, to drive the generator for electricity generation, and the generated AC form electricity is subsequently converted into stable DC bus voltage by a power electronic converter. The hardware and control design of the extended-range power supply system have been finalized and validated through experimental trials. Results demonstrate the system’s capability to sustain a stable DC bus voltage amidst disruptions such as sudden load shifts and fluctuations in prime mover speed. Even with 50% sudden load change, the voltage drop is within 12% and could recover to ±3% within 4 seconds. The range extender can be used alone without battery to power the electric tractor, or it can used in parallel with other extended-range extenders or battery thanks with the droop control ability for power sharing.

In the proposed article, the issues of increasing the synchronizing ability of the system of coordinated rotation of asynchronous motors are considered. Based on the T-shaped equivalent circuit, electromechanical relationships were obtained with changes in the value of the total rotor resistance and the supply voltage of individual motors. An algorithm for calculating the torques, stator and rotor currents of the motors of the system has been compiled. Based on the calculations obtained, the mechanical characteristics of the system asynchronous motors are constructed for various values of total resistance, supply voltages and rotor positions. The obtained data and graphs confirm the adequacy of the theory obtained in an analytical way. Functional and structural diagrams in small scales have been compiled, which allow simulating transient operation modes of multi-motor asynchronous electric drives in the Matlab application package. Multi-motor asynchronous electric drives with adjustable supply voltages, as well as with preliminary synchronization and synchronous braking, have been developed. Compilation of a program for the stability of a nonlinear system of a multi-motor asynchronous electric drive (MAEDs) with a thyristor voltage converter (TVC) in Matlab. Also, the modes of soft start, load shedding and surge on the motor shaft are simulated, confirming the stability of the system.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

This paper proposes an optimization method for the scheduling of a multi-energy virtual power plant supply-demand balance in the power market environment of Jiangxi Province. The objective of this method is to enhance the operational efficiency of the power grid, reduce energy costs, and facilitate economical and efficient energy distribution in the power market. The method comprehensively considers the characteristics and uncertainties of renewable energy sources such as solar and wind energy, and incorporates advanced multi-objective optimization algorithms. Additionally, real-time market price feedback is integrated to achieve accurate allocation of power supply and demand. Through a case study of a multi-energy virtual power plant in Jiangxi Province, this paper examines the optimal combination model for various energy sources within VPP, and analyzes the impact of different market environments on supply-demand balance. The results demonstrate that the proposed scheduling optimization method significantly improves economic benefits while ensuring grid stability. Compared with traditional power supply models, it reduces average electricity costs by 15% and increases renewable energy utilization efficiency by 20%.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

The growing use of proton-exchange membrane fuel cells (PEMFC) in hybrid propulsion systems, aimed at replacing traditional internal combustion engines and reducing greenhouse gas emis-sions. Effective power distribution between the fuel cell and the energy storage system (ESS) is crucial, which has led to a growing emphasis on developing energy management systems (EMS) to efficiently implement this integration. To address this goal, this study examines the performance of a fuzzy logic rule-based strategy for a hybrid fuel cell propulsion system in a small hydro-gen-powered passenger vessel. The primary objective is to optimize fuel efficiency, with particular attention to reducing hydrogen consumption. The analysis is carried out under typical operating conditions encountered during a river trip. Comparisons between the proposed strategy with other approaches —control-based, optimization-based and deterministic rule-based— are con-ducted to verify the effectiveness of the proposed strategy. Simulation results indicated that EMS based on fuzzy logic mechanisms was the most successful in reducing fuel consumption. The superior performance of this method stems from its ability to adaptively manage power distri-bution between the fuel cell and energy storage systems.

The examination of ampacity in overhead transmission lines offers a comprehensive overview, covering its definition, thermal evaluation methodologies, standards, practical applications, and the potential of high-temperature low-sag (HTLS) conductors. By navigating through static and dynamic approaches to thermal evaluation and detailing methodologies prescribed by international standards like those from CIGRE and IEEE, this study provides a solid understanding of how ampacity is determined and optimized. Furthermore, the exploration of HTLS conductors introduces a forward-looking perspective on enhancing transmission capacity whereas mitigating the need for extensive infrastructure modifications. Through an analysis of regional considerations and preferences using Slovak standards and CIGRE Technical Brochure 601, insights are provided on how environmental factors influence transmission line performance. The analysis of the transition from traditional ACSR to advanced ACCC (Aluminium Conductor Composite Core) conductors demonstrates the tangible benefits of adopting advanced conductor technologies in real-world scenarios.

The methods of Artificial Intelligence (AI) have been used in the planning and operation of power systems for more than 40 years. In recent years, due to the development of microprocessor and data storage technologies, the effectiveness of this use has greatly increased. This paper provides a systematic overview of the application of AI including the use of Machine Learning (ML) to the power system. The potential application areas are divided into four blocks and the classification matrix has been used for clustering the AI application tasks. Furthermore, the data acquisition methods for setting the parameters of AI and ML algorithms are presented and discussed in a systematic way considering the supervised and unsupervised learning methods. Based on this, three complex application examples: wind power generation forecasting, smart grid security as-sessment (using two methods), and automatic system fault detection are presented and discussed in detail. Summary and outlook conclude the paper.

Large Language Models (LLMs) have emerged as powerful tools in the domain of artificial intelligence, specifically enhancing natural language processing capabilities. These models leverage extensive datasets and sophisticated algorithms to automate and enhance tasks traditionally performed by humans, thereby revolutionizing innovation and entrepreneurship. LLMs accelerate product development, streamline business operations, and enable precise and rapid decision-making, all of which are crucial for maintaining competitiveness in dynamic markets. This paper categorizes the applications of LLMs in innovation and entrepreneurship into three main areas: technological innovation, strategic decision-making, and process automation. By exploring various integrations of LLMs in entrepreneurial ventures, this work offers both theoretical insights and practical examples, underscoring the transformative impact of LLMs in shaping modern business landscapes.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Battery electric vehicles provide an opportunity to balance supply and demand in future power systems with high shares of fluctuating renewable energy. Compared to other storage systems such as pumped-storage hydroelectricity, electric vehicle energy demand is highly dependent on charging and connection choices of vehicle users. We present a model framework of a utility-based stock and flow model, a utility-based microsimulation of charging decisions, and an energy system model including respective interfaces to assess how the representation of battery electric vehicle charging affects energy system optimization results. We then apply the framework to a scenario study for controlled charging of nine million electric vehicles in Germany in 2030. Assuming a respective fleet power demand of 27 TWh, we analyze the difference between power-system-based and vehicle user-based charging decisions in two respective scenarios. Our results show that taking into account vehicle users’ charging and connection decisions significantly decreases the load shifting potential of controlled charging. The analysis of marginal values of equations and variables of the optimization problem yields valuable insights on the importance of specific constraints and optimization variables. In particular, state-of-charge assumptions and representing fast charging drive curtailment of renewable energy feed-in and required gas power plant flexibility. A detailed representation of fleet charge connection is less important. Peak load can be significantly reduced by 5% and 3% in both scenarios, respectively. Shifted load is very robust across sensitivity analyses while other model results such as curtailment are more sensitive to factors such as underlying data years. Analyzing the importance of increased BEV fleet battery availability for power systems with different weather and electricity demand characteristics should be further scrutinized.

Increasing distributed generation and intermittency, along with the increasing frequency of extreme weather events, impose a serious challenge for the electric power supply security. Understanding the costs of interruption is vital in terms of enhancing the power system infrastructure and planning the distribution grid. On the other hand, customer rights and demand response techniques are further reasons to study the worth of power reliability. In this paper, the authors make use of directional distance function and shadow pricing method for a case study from Finland. The aim is to calculate the cost of one minute of power interruption from the distribution network operator perspective. The sample consists of 78 distribution network operators from Finland with cost and network information between 2013 and 2015.

This paper proposes the impact of plug-in electric vehicles integrated into power distribution system based on voltage dependent control. The plug-in electric vehicles was modeled as the static load model in power distribution systems under balanced load condition. The power flow analysis is determined by using the basic parameters of the electrical network. The main point of this study are compare with voltage magnitude profiles, load voltage deviation, and total power losses of the electrical power system. There are investigating the affected from constant power load, constant current load, constant impedance load and plug-in electric vehicles load, respectively. The IEEE 33 bus test system is used to test the proposed method by assigning each load type to a balanced load in steady state and applied the solving methodology based on the bus injection to branch injection matric, branch current to bus voltage matrix, and current injection matrix to solve the power flow problem. The simulation results showed that the plug-in electric vehicles load had the lowest impact compared to other loads. The lowest plug-in values for the electric vehicle loads were 0.062, 119.67 kW and 79.31 kVar for the load voltage deviation, total active power loss and total reactive power loss, respectively. Therefore, this study can be verified that the plug-in electric vehicles load were affected to the lowest of the electrical power system in condition to same sizing and position. So that, in condition to the plug-in electric vehicles load added into the electrical power system with the conventional load type or complex load type could be considered that the affected from the plug-in electric vehicles load in next study.

Countless disasters have resulted from climate change, causing severe damage to infrastructure and the economy. These disasters have significant societal impacts, necessitating mental health services for the millions affected. To prepare for and respond effectively to such events, it is crucial to understand people's emotions and the life incidents they experience both before and after a disaster strikes. In this case study, we mined the emotions and life incidents expressed on Twitter during the 2017 Hurricane Harvey. Between August 20 and August 30, we collected a dataset of approximately 400,000 public tweets related to the storm. Using a BERT-based model, we predicted the emotions associated with each tweet. Following emotion prediction, we applied various natural language processing techniques to analyze the content of the tweets, aiming to uncover the 'topics' discussed alongside specific 'emotions.' To efficiently identify these topics, we utilized the Latent Dirichlet Allocation (LDA) technique for topic modeling, which allowed us to bypass manual content analysis and extract meaningful patterns from the data. However, rather than stopping at topic identification, we further refined our analysis by integrating Graph Neural Networks (GNN) and Large Language Models (LLM). The GNN was employed to generate embeddings and construct a similarity graph of the tweets, which was then used to optimize clustering. This step ensured that related tweets were accurately grouped together based on their content and context. Subsequently, we used an LLM to automatically generate descriptive names for each event cluster. This advanced approach allowed us to identify and label life incidents automatically, providing a nuanced understanding of the key issues faced by the community during the hurricane. The results revealed significant emotional shifts as the hurricane reached its most devastating phase. These shifts coincided with pressing concerns and demands from the population, such as evacuation plans, animal safety, safety updates, public policy, help requests, flood impacts, and the spread of fake news. By combining GNN and LLM for automatic event name prediction, our study not only mapped out the emotions but also accurately categorized the specific life incidents that were most relevant during the disaster, offering critical insights for disaster preparedness and response strategies.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

The increasing deployment of intermittent renewable energy sources necessitates effective methods for balancing the electrical grid to ensure stability and safety. Energy storage systems that can store excess electrical power during periods of low demand and release it during high demand are crucial for both short-term and long-term applications. Power-to-Gas is an innovative energy storage solution that converts surplus renewable electricity into gas fuels, such as hydrogen, which can be stored and used later. This hydrogen can serve multiple purposes, including energy storage and as fuel for transportation modes like cars, trams, trains, and buses. While most hydrogen today is derived from fossil fuels, solid-oxide electrolysis (SOE) offers a cleaner alternative by producing hydrogen without harmful emissions. SOE is also the most efficient method of electrolysis. This study aims to determine the operational parameters for an SOE system, including lower heating value (LHV)-based efficiency and total input power, using a mathematical model. Results are presented for three different operating temperatures and four different steam utilization ratios. The paper is structured as follows: the introduction provides the context and motivation for the study; the second section outlines the fundamentals of electrolysis and its various types; the third section delves into solid-oxide electrolysis and electrolyser systems; the fourth section describes the methodology, including the mathematical formulation and simulation software used; the fifth section presents the calculation results and conclusions; and the final section summarizes the findings.

Building a new-type power system is the key core of the green and low-carbon development of energy, the restructuring of the power system will inevitably have a linked impact on the coordinated development of the economy-energy-environment (3E) system. This paper constructs a "Dual-Triangle" theoretical framework consisting of the “Energy Trilemma” and the "Sustainable Development Triangle", by combining historical statistical analysis with scenario predictive analysis, analyzes the historical characteristics of the "Dual Triangle" and future development trends under different scenarios, and studies the coupled interaction relationship of the "Dual-Triangle" to explore the optimal transformation path of the power system that is most beneficial to the coordinated development of the 3E system. The conclusions are as follows: (1) The energy system gradually inclined towards economy and cleanliness from 2010 to 2022, the level of coordinated development of the 3E system fluctuated upwards, and the operation status of the "Dual Triangle" was stable. (2) Positive coupling relationship between "Dual Triangle" of scenario S1 is close, which can be regarded as the preferred path for the reconstruction of the power system. Due to phased development has clear development priorities, scenario S2 will artificially break the balance of the “Energy Trilemma”, which is a development model that dynamically mitigates the challenges of the “Energy Trilemma”.(3)The contradiction between economy and cleanliness is continuously weakened, and security has become the core contradiction of the "Impossible Triangle". The combination of renewable energy and energy storage is the key to resolving this contradiction. This paper conducts an integrated and innovative application of the "Dual-Triangle" theory, and the results provide a case basis for how to achieve the coupled interaction of the "Dual-Triangle", promote high-quality energy development, and support the sustainable development of the economy and society.

Drought stress severely affects the normal growth and development of wheat, leading to reduced yields and quality. To address the lag and limitations of traditional drought monitoring methods, this paper proposes a drought stress monitoring model for winter wheat during critical growth stages based on deep learning. By acquiring drought stress images of winter wheat during three critical growth stages: rise-jointing, heading-flowering and flowering-maturity, a dataset correlating these images with soil moisture monitoring data was established. The DenseNet121 network model was selected as the base network to extract phenotypic features of winter wheat under drought stress. Variables such as the model's training approach, changes in learning rate, and whether an attention mechanism was included, were used to conduct eight sets of model training and optimization strategy experiments. A drought stress monitoring model for winter wheat during critical growth stages based on an improved DenseNet-121 was constructed. The results showed that the average recognition accuracy of the eighth group in the test set reached 94.67%, indicating good application prospects in the recognition of drought stress levels during critical growth stages of wheat.

In view of the problem that the output thrust of solenoid actuator is affected by various factors and is difficult to calculate in actual working conditions, this paper proposes a semi-analytical model constructed by magnetic field subdomain method with internal and external boundary conditions in cylindrical coordinate system for calculation, and the general solution equations of magnetic vector potential for each subdomain are derived and solved by MATLAB. Taking a push-pull electromagnet as an example, the finite element simulation and experimental comparative analysis are carried out. The correctness and applicable conditions of the subdomain method are illustrated by comparing the gradient plot of magnetic vector potential, inductance curve and electromagnetic force. By calculating the output thrust after considering the core gravity, spring force and electromagnetic force, it is shown that this method has the advantage of computational flexibility compared with the finite element method, and it is easier to write special algorithms according to various working conditions to calculate the important parameters in engineering applications.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

Crawling robots are the focus of intelligent inspection research, and the main feature of this type of robot is the flexibility of in-plane attitude adjustment. The crawling robot HIT_Spibot is a new type of steam generator heat transfer tube inspection robot with a unique mobility capability different from traditional quadrupedal robots. This paper introduces a hierachical motion planning approach for HIT_Spibot, aiming to achieve efficient and agile maneuverability. The proposed method integrates three distinct planners to handle complex motion tasks: a nonlinear optimization-based base motion planner, a TOPSIS-based base orientation planner, and a Mask-D3QN (MD3QN) algorithm-based gait motion planner. Initially, the robot's base and foot workspace are delineated through envelope analysis, followed by trajectory computation using Larangian methods. Subsequently, the TOPSIS algorithm is employed to establish an evaluation framework conducive to foundational turning planning. Finally, the MD3QN algorithm trains foot points to facilitate robot movement along predefined paths. Experimental results demonstrate the method's adaptability across diverse tube structures, showcasing robust performance even in environments with random obstacles. Compared to the D3QN algorithm, MD3QN achieves a 100% success rate, enhances average overall scores by 6.27%, reduces average stride lengths by 39.04%, and attains a stability rate of 58.02%. These results not only validate the effectiveness and practicality of the method but also showcase the significant potential of HIT_Spibot in the field of industrial inspection.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

In numerical simulations, achieving high accuracy without significantly increasing computational costs is often challenging. To address this, this paper presents an improved finite volume weighted essentially non-oscillatory (WENO) scheme tailored for applicability in computational fluid dynamics (CFD) and implemented in the flow solver NUAA-Turbo for simulating turbomachinery flows using both RANS and RANS/LES coupling. Firstly, the new WENO scheme is validated against classic numerical test cases to assess its stability and reliability in handling discontinuities, the Double problem, and Raleigh-Taylor (RT) instability issues. Compared to the original format, this enhanced finite volume WENO scheme demonstrates superior stability near discontinuities and resolves flow features with the same grid resolution more effectively. Next, for engineering applications related to turbomachinery, such as compressor and turbine characteristics, computations are performed using RANS, and the results obtained using WENO-ZQ3 and WENO-JS3 are compared. Finally, the new fifth-order WENO scheme is applied to RANS/LES coupled simulations of turbine wakes and film cooling. The results show that the enhanced finite volume WENO scheme offers improved stability and accuracy in engineering applications, allowing for high-precision calculations with fewer grid points to capture more detailed flow physics, thereby reducing computational costs in aerodynamic applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To enhance the peak-shaving capability of the boiler, a mathematical model of hydrodynamic and wall temperature characteristics for the water-cooled wall of a 1000 MW boiler was established. The attributes pertaining to the mass flow distribution, the temperature of the effluent working fluid, pressure drop, and the thermal distribution across the wall surfaces at 30% of the boiler's maximum continuous rating (BMCR) were meticulously computed and subjected to a thorough analytical review. The findings suggest that, under the operation at 30% BMCR load, there is a substantial equilibrium in the flow distribution across the quartet of walls that constitute the water-cooled wall assembly. The maximum mass flow rate deviations in the helical and vertical sections are 1.95% and 3.47%, respectively, showing small flow deviations and reasonable distribution. The temperature deviation in the helical section is 0.3 °C, reflecting the characteristic low thermal deviation in helical tubes. While the temperature deviation at the outlet of the vertical section is higher, it remains within safe limits. The pressure loss across the water-cooled wall system amounts to 0.4 MPa. The peak wall temperature reaches 337.5°C, remaining within the material's permissible safety limits. In-depth performance analysis ensures the safe operating conditions of the water-cooled wall during low load conditions.

The shift towards autonomous excavators in construction and mining is a significant leap towards enhancing operational efficiency and ensuring worker safety. However, it presents challenges such as the need for sophisticated decision-making and environmental perception due to complex terrains and diverse conditions. Our study introduces the E-GTN framework, a novel approach tailored for autonomous excavation that leverages advanced multisensor fusion and a custom-designed convolutional neural network to address these challenges. Results demonstrate that GridNet effectively processes grid data, enabling the reinforcement learning algorithm to make informed decisions, thereby ensuring efficient and intelligent autonomous excavator performance. The study concludes that the E-GTN framework offers a robust solution for the challenges in unmanned excavator operations, providing a valuable platform for future advancements in the field.

As a critical component of electric vehicles, the powertrain has a significant impact on the overall performance of the vehicle. In addressing the challenge of lengthy testing cycles, this study develops a para model of the powertrain utilizing digital twin (DT) technology, thereby establishing a framework for simulation testing of multi-controller intermodulation. The research conducts functional definition coverage testing through the design of specific functional requirement use cases, and it validates the failure mechanism via fault injection use cases. The results indicate that the DT testing platform can effectively simulate the operational interactions among various controllers within the powertrain system. In comparison to traditional field testing, the digital twin-based testing methodology offers enhanced operational efficiency and allows for the examination of testing conditions that are impractical to implement in real vehicles, particularly in the context of fault injection testing, thus facilitating the early detection of potential safety risks within the system. The advancement of this technical solution holds significant practical implications for the future mass production and development of electric vehicles.

In modern warfare, the diversified tasks can sometimes be challenging to fulfill with a single projectile, necessitating the incorporation of cooperation constraints in trajectory planning. Limited by the stringent requirements of the launch platform and lower costs, the maneuverability and ability to adjust the flight time range of projectiles are weak. Therefore, the rationality of performance indicators and flight time coordination strategies is especially critical. To fully exploit the control capabilities of projectiles, a battlefield area segmentation method is proposed, differentiated performance indicators and a cooperative trajectory planning model that considers the entire range of projectiles are established. Considering the limitations of existing flight time coordination strategies in applications, targeted improvements have been made in different cooperation scenarios, and a bi-level adaptive cooperation strategy(BACS) with both optimality and flexibility is proposed. To rapidly determine feasible conditions, a simple and universal method for obtaining the capability ranges of cooperation is introduced. The multi-phase optimal control problems are transformed into nonlinear programming problems using the Radau pseudo-spectral method, and simulation results show that the proposed methods are capable of handling trajectory planning tasks in different cooperation scenarios. The improved strategies effectively enhance the planning success rate under relatively harsh conditions and BACS demonstrates good compatibility with the problems studied.

Due to constraints in launch platform and cost, the maneuverability of gliding-guided projectiles is limited, necessitating a rational design of their trajectory schemes. To reduce the sensitivity of trajectory schemes to uncertainties while ensuring compatibility between flight schemes and guidance control systems, and fully exploiting the control capability of the projectile, a closed-loop robust trajectory planning method is proposed. Models of major uncertain factors and states deviation at the control-start point are established. Based on the NIPCE method, the stochastic dynamic model is transformed into a high-dimensional deterministic model with PCE coefficients as state variables, and the uncertainty propagation law is obtained. A PID algorithm is employed to design a tracking guidance law based on position error feedback, and open-loop and closed-loop robust trajectory planning models are established accordingly. The optimal control problem is solved by transforming it into a nonlinear programming problem using the direct shooting method. Simulation results indicate that the NIPCE method can significantly improve the computational efficiency of uncertainty propagation while ensuring accuracy. Open-loop robust planning can effectively mitigate the sensitivity of gliding trajectories to uncertainties but cannot completely eliminate terminal dispersion. Closed-loop robust planning effectively improves control effort consumption on the basis of open-loop planning.

There are various types of charged particles in the space environment, which can cause different types of radiation damage to materials and devices, leading to on-orbit failures and even accidents of spacecraft. Developing lightweight and efficient radiation shielding materials is an effective approach to improve the inherent protection of spacecraft. The protective performance of different materials against proton and electron spectra in the Earth’s radiation belts is evaluated by Geant4 simulation. Based on the simulation results, suitable hardening components are selected to design composite materials, and B4C/PEEK composites with different B4C content were successfully prepared. Experimental results demonstrate that the simulated and experimental results for the electron, proton and neutron shielding performance of B4C/PEEK composites are consistent. These composites exhibit excellent radiation shielding capabilities against electrons, protons and neutrons, and the radiation protection performance improves with increasing B4C content in the B4C/PEEK composite materials.

The article discusses issues related to the optimization of the operation of medium voltage networks, focusing on the optimization of network division points and the selection of the optimal network configuration aimed at reducing power and energy losses. The article provides a critical review of selected scientific works from recent years on the issue of network configuration optimization. The developed solution uses non-deterministic network models and statistical and probabilistic approaches. Optimization studies were carried out using heuristic optimization methods and proprietary algorithms for forecasting the load and power generated from renewable energy sources. The solution proposed in the article has many application possibilities. It can be used to optimize the location of network division points (reducing economic costs related to the modernization of network infrastructure) as well as to optimize the reconfiguration process in order to reduce power losses while maintaining voltage criteria.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

The development and utilization of wind energy is of great significance to the sustainable development of China's economy and the realization of the goal of "dual carbon". Under the typhoon system, the randomness and volatility of wind speed become an important basis for affecting the energy efficiency utilization and design of wind turbines. Therefore, based on wind speed and wind direction data at 10m, 30m, 50m and 70m heights of a wind power tower in Yancheng, Jiangsu Province, this paper analyzes the change characteristics of wind speed and wind direction by using BFAST method and Hurst index. Based on typhoon body data, topographic data and mesoscale system wind direction data, the causes of the occurrence and development of wind speed and wind direction of wind tower are further analyzed, and a conclusion is drawn: (1) In BEAST method, there are 5, 5, 6 and 6 change points at the height of 10m, 30m, 50m and 70m respectively. Among them, the change points at the height of 10m, 30m and 50m all change before and after node 325, and the change time point at the height of 70m is inconsistent with other heights. Hurst index results show that the inconsistency at 70m altitude is stronger than that at other altitudes. (2) The wind direction sequence at 10m, 30m, 50m and 70m altitude is fitted by stages, and the direction of wind direction is SE-E-SE-SW-W-NW, where, At the height of 70m, the deviation of the fitting trend line from other altitudes is larger in the wind speed strengthening stage and weakening stage. (3) The wind speed at the height of 10m and 70m has different response degrees to the typhoon body. The correlation between the wind speed and the distance between the wind measurement tower and the typhoon near the center is stronger at the height of 10m than at the height of 70m. The surface type and the wind direction of the mesoscale system also have certain effects on the wind speed and direction. In this paper, the change characteristics and influencing factors of wind speed and direction of wind tower are studied, which provides methods and theoretical support for the study of short-term wind speed when typhoon passes through, and provides reliable support for the selection of wind power forecast indicators and the selection and design of wind turbines under extreme gale weather systems.

In this paper a variable’s involved in assessing the quality of a distributed generation system are reviewed, aiming to minimize the electric power losses (unused power consumption) and optimize the voltage profile. To provide this assessment, several experiments have been made to the IEEE 34-bus test case and various actual test cases with the respect of multiple DG units. The possibility and effectiveness of the proposed algorithm for optimal placement and sizing of DG in distribution systems have been verified. Finally, four algorithms were trailed: simulated annealing (SA), hybrid genetic algorithm (HGA), genetic algorithm (GA) and variable neighbourhood search. The HGA algorithm was found to produce the best solution at a cost of longer processing time.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

The insufficient flexibility of the hybrid renewable integrated energy system (HRIES) makes it difficult to accommodate renewable energy with a high proportion. It is thus necessary to excavate its potential flexibility to improve its operational performance and consume renewable energy. This paper unlocks the adjustment potential of flexible buildings and builds a flexible thermal load regulation model according to the dynamic thermal characteristics and thermal comfort elastic interval of the buildings and a regulation model of the flexible electrical load based on its transferability, resectability, and rigidity. An operation optimization model, which incorporates multiple flexible load regulations and the variable load of devices, is then developed. A case study is presented to analyze the regulation and synergy mechanism in different types of flexible loads. Its results show a saturation effect between the flexible thermal and electrical loads in increasing renewable energy consumption and a synergy effect in decreasing the total cost. This synergy can reduce the total cost by 0.73%. Besides, the total cost can be reduced by 15.13%, and the renewable energy curtailment rate can decrease by 12.08% if the flexible electric and thermal loads are integrated into the operation optimization of HRIES.

Tackling the intricacies of network dismantling in complex systems poses significant challenges. This task has relevance across various practical domains, yet traditional approaches focus primarily on singular metrics, such as the number of nodes in the Giant Connected Component (GCC) or average pairwise connectivity. In contrast, we propose a unique metric that concurrently targets nodes with the highest degree and reduces the GCC size. Given the NP-hard nature of optimizing this metric, we introduce MaxShot, an innovative end-to-end solution that leverages graph representation learning and reinforcement learning. Through comprehensive evaluations on both synthetic and real-world datasets, our method consistently outperforms leading benchmarks in accuracy and efficiency. These results highlight MaxShot’s potential as a superior approach to address the network dismantling problem effectively.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

Это исследование сосредоточено на разработке системы искусственного зрения для гибкого дельта-робота-манипулятора и ее интеграции с межмашинной связью для оптимизации взаимодействия устройств в реальном времени. Эта интеграция направлена ​​на увеличение скорости роботизированной системы и улучшение ее общей производительности. Предлагаемое сочетание системы искусственного зрения с межмашинной связью позволяет обнаруживать и распознавать цели с высокой точностью в режиме реального времени в ограниченном пространстве, предназначенном для позиционирования, дальнейшей локализации и выполнения производственных процессов, таких как сборка или сортировка деталей. . В данном исследовании RGB-изображения используются в качестве входных данных для алгоритма MASK-R-CNN, а результаты обрабатываются в соответствии с особенностями прототипа дельта-манипулятора робота. Данные, полученные от MASK-R-CNN, адаптированы для использования в системе управления дельта-роботом с учетом ее уникальных характеристик и требований к позиционированию. Технология M2M позволяет манипулятору робота быстро реагировать на изменения, например, на перемещение объектов или изменение их положения, что имеет решающее значение для задач сортировки и упаковки. Система была протестирована в условиях, близких к реальным, чтобы оценить ее производительность и надежность.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

As the penetration of renewable energies increases, their acceptance of the power grid system is becoming an important issue. In the case of South Korea, a 22.9kV transformer is frequently utilized to reduce the power loss of the generated renewable energy transmission, so the power quality at the point of common connection (PCC) is inevitably influenced by the nonlinearity of the transformer and the uncertainty of the inductance and resistance of the transmission line. In this paper, we present a point of common connection voltage-modulated direct power control (PCCVM-DPC) system that enhances power quality at the PCC. First, we present the mathematical dynamics of active and reactive power at the PCC side, which contains the step-up transformer’s nonlinearity, the grid voltage harmonics, and the parameter uncertainties. By analyzing the disturbance terms of the PCCVM-DPC system, we present the disturbance observer (DOB) for the PCCVM-DPC system. To assess the efficacy of our approach, we perform comparative studies of the PCCVM-DPC without DOB and PCCVM-DPC with DOB by constructing the simulation environment based on the commercial step-up transformer and ESS inverter datasheet. We have validated that the active and reactive power control performance of the PCCVM-DPC with DOB outperforms the PCCVM-DPC without DOB from the observation that the current total harmonic distortion reduced by more than 40% compared to the PCCVM-DPC without the DOB.

This study investigates cloud cavitation suppression around a model scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift-drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor-liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift-drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems.

The increased adoption of information and communication technology for smart grid applications will require innovative cyber-physical system (CPS) testbeds to support research and education in the field. The groundbreaking CPS testbeds with realistic and scalable platforms have progressively gained interest in recent years, with electric power flowing in the physical layer and information flowing in the network layer. However, CPSs are critical infrastructures and not designed for testing or direct training, as any misbehaving in an actual system operation could cause a catastrophic impact on its operation. Based on that, it is not easy to efficiently train professionals in CPSs. Aiming to support the advancement and encourage the training of industry professionals, this paper proposes and develops a complete testbed with commercial tools. The testbed can reliably replicate the performance of smart grid systems and the main potential cyber threats that electric grids may face. The complex interdependencies between the cyber and physical domains are discussed in detail, and different case scenarios are presented, providing insightful guidelines for key features and design decisions for future smart grid testbeds.

The next-generation communication systems demand integration of sensing, communication, and power transfer (PT) capabilities, requiring high spectral efficiency, energy efficiency, and low cost, while also necessitating robustness in high-speed scenarios. Integrated sensing and communication systems (ISACS) exhibit the ability to simultaneously perform communication and sensing tasks using a single RF signal, while simultaneous wireless information and power transfer (SWIPT) systems can handle simultaneous information and energy transmission, and orthogonal time frequency space (OTFS) signals are adept at handling high Doppler scenarios. Combining the advantages of these three technologies, a novel cyclic prefix (CP) OTFS based integrated simultaneous wireless sensing, communication, and power transfer system (ISWSCPTS) framework is proposed in this work. Within the ISWSCPTS, the CP-OTFS matched filter (MF) based target detection and parameters estimation (MF-TDaPE) algorithm is proposed to endow the system with sensing capabilities. To enhance the system’s sensing capability, a waveform design algorithm based on CP-OTFS ambiguity function shaping (AFS) is proposed, which is solved by iteratively method. Furthermore, to maximize the system’s sensing performance under communication and PT Quality of Service (QoS) constraints, a semidefinite relaxation (SDR) beamforming design (SDR-BD) algorithm is proposed, solved using through SDR technique. Simulation results demonstrate that the ISWSCPTS exhibits stronger parameter estimation performance in high-speed scenarios compared to orthogonal frequency division multiplexing (OFDM), waveform designed by CP-OTFS AFS demonstrates superior interference resilience, and beamforming designed by SDR-BD strikes a balance in the overall performance of the ISWSCPTS.

Developing a dependable gas and condensate value chain is vital for the ongoing prosperity of the oil and gas industries. To achieve this, NNPC is enhancing its production facilities by employing process modeling and simulation with the assistance of Symmetry iCON®. As a part of this initiative, a simulation model was created using the Symmetry iCON® pipe plexus solver to simulate the dynamic environment of the gas and condensate pipeline network in the Nigerian Southern region. To validate the model, data from a single month, specifically December 2022, was utilized. Furthermore, the algorithm was utilized to generate projections for the month of January 2023, providing valuable insights into its effectiveness. The study also highlighted the significance of accurately estimating the characteristics and properties of a pseudo component of C6+ in relation to thermodynamics and material properties, which was a particularly insightful finding. he assessment of this property has transitioned from being relatively unimportant to becoming critically important, primarily due to the lack of condensate data monitoring at specific terminals. However, it's worth noting that the model currently has an error margin of 4-6% when predicting the data. As more information becomes available in the future, the model can be easily fine-tuned to better align with the actual conditions, allowing for more accurate predictions.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

In terahertz communication systems, lens antennas used in transceivers are basically plano-convex dielectric lenses. As the aperture increases and the focal length decreases, the thickness and mass of the plano-convex lens increase rapidly. Through theory and simulation, we designed a Fresnel lens suitable for the terahertz band to meet the requirements of large aperture and short focal length, and simulated the performance, advantages and disadvantages of the terahertz Fresnel lens. A 300GHz terahertz wireless communication system was built to verify the gain effect of the Fresnel lens antenna. The experimental results show that the Fresnel lens can amplify the signal in the terahertz band. The theoretical gain of a 30 cm Fresnel lens is 48.83dB, while the actual measured gain is approximately 45dB.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

The use of optical fibers is increasing in modern aircraft because it helps solve challenges of size, weight, communication, and reliability in new aircraft generation. This work describes a video and power transmission system using optical fibers (PoF) for in-flight entertainment (IFE) system application. We present the benefits and the limitations of this application, and we perform two practical experiments to demonstrate their performance. It used off-the-shelf devices in the experiments, such as one 15-W semiconductor laser operating at 808 nm, GaAs photovoltaic converters, optical transmitters and receivers, and video monitors. The power and video signals were transmitted using two 50-m multimode fibers. In addition, we proposed and tested two types of energy transformation units (ETU), which are responsible for supplying electrical energy to the IFE video monitor and the optical fiber receiver.

To ensure sustainability of the future power grid, the rate of expansion of distributed renewable energy resources (DRER) has introduced operational challenges. These includes managing transmission constraints with DRER power injection, dispatching DRER efficiently, managing system frequency and ensuring sufficient reactive power for voltage support. Coupled with the intensification of wildfires, power infrastructure across the United States faces challenges to minimize the impact to maintain system reliability and resiliency. This research embarks on a comprehensive evaluation, beginning with an in-depth historical analysis to delineate regions most susceptible to wildfires. Utilizing a multidimensional approach, the study assesses wildfire-induced risks to power grids, by integrating historical wildfire occurrences, real-time wildfire proximities, Moderate Resolution Imaging Spectroradiometer (MODIS) derived vegetation metrics, and system parameters, by employing Principal Component Analysis (PCA) based optimal weights, leading to the formulation of a novel risk factor model. This risk factor has the potential to be the key to ensuring the resilience of a renewable-rich smart grid when faced with a severe weather event. Our model’s applicability was further verified through an empirical assessment, selecting representative networks from diverse regions, providing insights into the geographical variability of risk factors. Ultimately, this study offers stakeholders and policymakers a comprehensive tool-set, empowering decisions regarding infrastructure investments, grid reinforcements, and strategic power rerouting to ensure consistent energy delivery using risk assessment against wildfire.

In the dynamic landscape of the telecommunications industry, understanding and mitigating customer churn is paramount for maintaining competitive advantage and sustaining revenue streams. This comprehensive literature review delves into the intricacies of customer churn prediction, a crucial aspect in fortifying the bond between telecom businesses and their customers. The review methodically analyzes 11 articles published between 2000 and March 2024, spotlighting the strategic role of Customer Relationship Management and the prevalence of high churn rates that necessitate a shift from customer acquisition to retention strategies. Furthermore, the review navigates through the challenges inherent in churn prediction, including the complexities of managing large, imbalanced, and noisy datasets and the intricacies involved in model selection and optimization. Despite these challenges, the paper highlights the superior capability of machine learning techniques in handling complex datasets to provide accurate predictions, albeit acknowledging their practical complexities. The main aim of the study is to provide an overview, serving as a knowledge base for researchers interested in machine learning techniques within the realm of telecommunications.

Intelligent fault diagnosis techniques have replaced the time-consuming and unreliable human analysis, increasing the efficiency of fault diagnosis. Deep learning model can improve the accuracy of intelligent fault diagnosis with the help of its multilayer nonlinear mapping ability. This paper has proposed a novel method named Deep Convolutional Neural Networks with Wide First-layer Kernels (WDCNN). The proposed method uses raw vibration signals as input (data augmentation is used to generate more inputs), and uses the wide kernels in first convolutional layer for extracting feature and suppressing high frequency noise. Small convolutional kernels in the preceding layers are used for multilayer nonlinear mapping. AdaBN is implemented to improve the domain adaptation ability of the model. The proposed model addresses the problem that currently, the accuracy of CNN applied to fault diagnosis is not very high. WDCNN can not only achieve 100% classification accuracy on normal signals, but also outperform state of the art DNN model which is based on frequency features under different working load and noisy environment.

Non-toroidal shape primary pass through protection current transformers (CTs) are used to measure high currents. Their design provides them with a big airgap that allow passing several cables per phase though them, which is the main advantage versus toroidal types, as the number of CTs required to measure the whole phase current is drastically reduced. The cables pass through the transformer window can be in several positions. As the isolines of the magnetic field generated by the primary currents are centered in the cables, if these cables are not centered in the transformer window, the magnetic field will be non-uniform along the transformer core. Consequently, local saturations can appear if the cables are not properly disposed causing the malfunction of the CT. In this paper, the performance of a non-toroidal shape protection CT is studied. The research is focused on the cable position influence in possible partial saturations of the CT when it is operating near to its accuracy limit. Depending on the cable position, the ratio of the primary and secondary currents can depart from assigned ratio. The validation of this phenomenon has been carried out via Finite Element Analysis (FEA) showing that partial transformer core saturations appears in areas of the magnetic core close to the cable. Applying FEA, also the admissible accuracy region for cable positioning inside the CT is delimited. Finally, the simulation results are ratified with experimental tests performed in non-toroidal protection CTs varying the primary cables’ positions, which are subjected to currents up to 5 kA, achieving satisfactory results. From this analysis, installation recommendations are given.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

The article presents several innovative systems developed through student laboratory projects, including two autonomous vehicles, a four-legged walking robot, an active ankle-foot orthosis, a ball on beam balancing mechanism, a ball on plate system, and a manipulator arm—all powered by pneumatic artificial muscles (PAMs). Fluidic muscles offer significant potential in various mechatronic systems, robots, and manipulators due to their flexible, lightweight nature and compliance. Their ability to produce smooth and adaptable motions is particularly beneficial in applications requiring natural and human-like movement, such as rehabilitation and assistive devices. Although PAMs powered control systems face challenges with nonlinear phenomena, their biologically inspired design holds promise for future applications across various industries. These may include innovative applicability in industrial, automotive, and aerospace sectors, as well as use in sports, medical aids, entertainment, and animatronics. Incorporating self-made laboratory systems actuated by PAMs into control systems education offers a comprehensive learning opportunity that combines theoretical concepts with hands-on experience. This approach develops the necessary skills of future engineers, expanding their understanding of technical principles and preparing them for future challenges in engineering practice.

Although data acquisition is a very usual technique, there are several aspects not always considered, as synchronization of acquired measures and evaluation of the errors that derive from this fact. The paper hereby aims to point this thing out, by mathematical determination of the necessary correction and implementing the software meant to evaluate the performances of the acquisition system. As an example, a three-phased acquisition system has been developed in order to monitor the currents and voltages on the three phases. Also other measures have been calculated, such as power and phase. The components on each phase don’t have to be fully identified because a whole system calibration can be made in the first stage. Calibration consists in finding the weighting coefficients for each quantity. The implemented solution for three-phased measures data acquisition starts from the hypothesis of a sampling frequency that respects Shannon theorem. The distance between two samples is small enough to consider a linear evolution between two moments for the same measure. Errors that affect the above mentioned, due to the different moments of time when samples are acquired, are analyzed and brought to the minimum value.

This study evaluates the effectiveness of Darknet53 and VGG16 pretrained models to develop a hybrid ensemble model named HybridPlantNet23 deep learning model for effective plant disease classification, using the publicly available dataset ‘A Dataset of Leaf Images’ from Mendeley webpage. The preprocessing of the dataset involved resizing the images to the respective requirements of the pretrained models to develop a combined datastore which served as the input. All experiments were conducted using MATLAB R2023b deep network designer interface. Model performances were evaluated based on the conventional accuracy, precision, recall, and F1-score. VGG16 achieved the highest accuracy (97.25%), precision (96.30%), recall (96.96%), and F1-score (96.55%), outperforming both Darknet53 and the ensemble HybridPlantNet23 model. Despite the advanced architecture of the ensemble model, its performance (accuracy: 95.37%, precision: 93.56%, recall: 94.20%, F1-score: 93.74%) was not significantly superior, thus highlighting scientific reasons behind this development. Recommendations for future works were provided accordingly.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

Traditional seismic wave-based tunnel advanced geological forecasting techniques are primarily designed for drill and blast method construction tunnels. However, given the fast excavation speed and limited prediction space in Tunnel Boring Machine (TBM) construction tunnels, traditional methods have significant technical limitations. This paper analyzes the characteristics of different types of TBM construction tunnels and, considering the practical construction conditions, identifies an effective observation system and data acquisition method. Utilizing numerical simulation, a model for advanced detection of typical unfavorable geological formations is established by obtaining the wave field response characteristics of seismic waves in three-dimensional space. The seismic wave reflection method can effectively receive information from unfavorable geological formations in front of the tunnel face. To address the challenges in advanced forecasting for TBM construction tunnels, a method of ellipsoid positioning velocity analysis, which takes into account the constraints of three-component data directions, is proposed. Based on the characteristics of the advanced forecasting observation system, the method compares the maximum values on the spatial isochronous ellipsoidal surface to determine the average velocity of the geological layer rays, thereby enabling accurate inversion of the spatial distribution ahead. Field verification of advanced geological forecasting based on ellipsoid positioning velocity analysis for TBM tunnels is conducted. The results indicate that this method can be used to obtain the three-dimensional velocity of the predicted unfavorable geological formations in front of the tunnel and is effective for the application of geological forecasting in TBM construction tunnels, thus providing crucial references and assurances for construction.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.