Electric torque wrenches play a crucial role in the assembly of high-strength bolts. This study focuses on three assembly processes for high-strength bolts and introduces a statistical analysis method to assess the quality of the bolt assembly. To enhance the performance, a novel, fully digital, Internet of Things (IoT) electric torque wrench is designed, incorporating a smart meter chip. This wrench achieves integration between the current sensor control method and the torque sensor control method using a simplified hardware circuit, ensuring high precision and stability. Additionally, this study employs the AC voltage self-stabilization method and Savitzky–Golay filtering method to enhance the accuracy and robustness of the wrench. Simulation experiments using Simulink and Matlab validate the effectiveness of these two methods. Furthermore, a cloud platform is utilized to enable rapid IoT access for the wrench, facilitating seamless connectivity and data transmission.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

Although the connection of implant abutments to implant analogs and implant bodies has been evaluated separately, comparative evaluation of connections to implant analogs and implant bodies has not been evaluated. The objective of this study was to identify whether torque applied during laboratory manufacturing and during restoration cementation affects the compatibility between the implant body-abutment and the implant analog-abutment, as well as to spot any structural differences. Three different implant system with internal conical connection (Bioinfinity, Dant, and Dentist) were used. For each group, straight abutments (n=20) were tightened to implant analogs (n=10) and implant bodies (n=10) with hand tightening and using torque wrench device. The fitting of componenets were evaluated for each group using linear and volumetric micro-CT analysis. For linear analysis, when the mean differences (difference between measurements of the linear distance of abutments during hand tightening and applying torque) values between implant analog and implant body were compared within groups, There was no statistically significant difference observed in all groups (p> 0.05). Throughout the fabrication and clinical phases, it is recommended to tighten the abutments on the analogs with a torque wrench instrument to minimize the risk of prosthetic incompatibility.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

In this study, a novel two-layer control scheme aimed at enhancing the dynamic performance of a nonlinear vehicle through the utilization of an optimal control approach grounded in predictive control principles is presented. The first layer of our control system focuses on the computation of an optimized rotational torque that ensures lateral dynamic stability. This torque is subsequently translated into differential forces acting on the wheels, employing the inverse tire model to derive the desired longitudinal slips. These slip values are then transmitted to the second layer of our control system. In the second layer, the electric motors associated with the vehicle's wheels dynamically adjust the input torque to accurately track the desired slip, thereby ensuring the overall stability of the electric vehicle. In view of the paramount importance of energy consumption in electric vehicles, we adopt optimal control strategies to substantially minimize battery utilization. To this end, careful selection of appropriate weighting coefficients in the control laws enables us to maintain the electric motors within their permissible operational range while simultaneously minimizing battery energy consumption for desired slip tracking. Extensive simulation results validate the effectiveness of our proposed control system in proficiently managing nonlinear effects and safeguarding the vehicle's stability.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

This paper presents a complete control strategy of the active return-to-center (RTC) control for electric power steering (EPS) systems. We first establish the mathematical model of the EPS system and analyze the source and influence of the self-aligning torque (SAT). Second, based on the feedback signals of steering column torque and steering wheel angle, we give the trigger conditions of a state switch between the steering assist state and the RTC state. In order to avoid the sudden change of the output torque for the driving motor when the state switches frequently between the steering assist state and the RTC state, we design an undisturbed state switching logic algorithm. This state switching logic algorithm ensures that the output value of the RTC controller is set to an initial value and increases in given steps up to a maximum value after entering the RTC state, and the output value of the RTC controller will reduce in given steps down to zero when exiting the RTC state. This therefore ensures smooth switch control between the two states and improves the driver’s steering feeling. Third, we design the RTC controller, which depends upon the feedback signals of the steering wheel angle and the angular velocity. In addition, the controller increases the auxiliary control function of the RTC torque based on vehicle speed. The experimental results show that the active RTC control method does not affect the basic assist characteristics, which effectively reduces the residual angle of the steering wheel at low vehicle speed and improves the RTC performance of the vehicle.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

In this paper, by evaluating extreme value of the qth-power current, a torque sharing function (TSF) family for reducing the torque ripples in the switched reluctance motor (SRM) is proposed. The optimization criteria of the TSF has two secondary objectives, including the maximization of the torque-speed range and the minimization of copper loss. The evaluation indices in terms of the peak phase current, the rms phase current, and the torque ripple factor are compared between the proposed TSF family and four conventional TSFs including linear, sinusoidal, exponential, and cubic TSFs. An optimization objective function that combines the maximum absolute value of the rate-of-change of the flux linkage (MAV-RCFL) and the qth-power of current is proposed and a weighting factor is used to balance the influence of the two optimization objectives. An optimal TSF can be easily obtained by solving the optimization problem from the TSF family. The proposed TSF is validated by using simulations and experiments with a three-phase 6/4 SRM with 7.5 kW, 3000 rpm, and 270 V DC-link voltage. The dynamic simulation model is implemented in Matlab/Simulink. The results demonstrate the validity and superiority of the proposed control method; the optimal TSF provides better torque-speed performance, and a better reduction in copper loss and torque ripples at high speed compared to the conventional TSFs obviously.

The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p<0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p<0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

In order to improve contrast and restore color for underwater image captured by camera sensors without suffering from insufficient details and color cast, a fusion algorithm for image enhancement in different color spaces based on contrast limited adaptive histogram equalization (CLAHE) is proposed in this article. The original color image is first converted from RGB color space to two different special color spaces: YIQ and HSI. The color space conversion from RGB to YIQ is a linear transformation, while the RGB to HSI conversion is nonlinear. Then, the algorithm separately operates CLAHE in YIQ and HSI color spaces to obtain two different enhancement images. The luminance component (Y) in the YIQ color space and the intensity component (I) in the HSI color space are enhanced with CLAHE algorithm. The CLAHE has two key parameters: Block Size and Clip Limit, which mainly control the quality of CLAHE enhancement image. After that, the YIQ and HSI enhancement images are respectively converted backward to RGB color. When the three components of red, green, and blue are not coherent in the YIQ-RGB or HSI-RGB images, the three components will have to be harmonized with the CLAHE algorithm in RGB space. Finally, with 4 direction Sobel edge detector in the bounded general logarithm ratio operation, a self-adaptive weight selection nonlinear image enhancement is carried out to fuse YIQ-RGB and HSI-RGB images together to achieve the final fused image. The enhancement fusion algorithm has two key factors: average of Sobel edge detector and fusion coefficient, and these two factors determine the effects of enhancement fusion algorithm. A series of evaluate metrics such as mean, contrast, entropy, colorfulness metric (CM), mean square error (MSE) and peak signal to noise ratio (PSNR) are used to assess the proposed enhancement algorithm. The experiments results showed that the proposed algorithm provides more detail enhancement and higher values of colorfulness restoration as compared to other existing image enhancement algorithms. The proposed algorithm can suppress effectively noise interference, improve the image quality for underwater image availably.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

Effective oral care is important to maintain a high quality of life. Therefore, plaque control can prevent the development and recurrence of periodontitis. Brushing with a toothbrush and toothpaste is a common way to remove plaque; however, excessive brushing or brushing with abrasive toothpaste can cause wear and tear on the dental crown. Hence, we aimed to quantitatively compare the plaque-removal efficiency and tooth wear of toothbrushes using bioelectric effect (BE) with those of mechanical electric toothbrushes. To generate the BE signal, an electronic circuit was developed and embedded in a toothbrush. Further, typodonts were coated with cultured artificial plaques and placed in a brushing simulator. A toothpaste slurry was applied, and the typodonts were eluted with tap water after brushing. The plaques of the typodonts were captured, and the images were quantified. For the tooth wear experiment, polymethyl methacrylate disk resin blocks were brushed twice a day, and the thickness of the samples was measured. Subsequently, statistical differences between the experimental toothbrushes and typical toothbrushes were analyzed. The BE toothbrush had a higher plaque-removal efficiency and could minimize tooth wear. This study suggests that the application of BE may be a new solution for oral care.

To assess the impact of a deep learning (DL) denoising reconstruction algorithm applied to identical patient scans acquired with two different voxel dimensions, representing distinct spatial resolutions. This IRB approved prospective study was conducted at a tertiary pediatric center in compliance with the Health Insurance Portability and Accountability Act. We used a General Electric Signa Premier unit (GE Medical Systems, Milwaukee, WI) to acquire two DTI sequences of the left knee on each child at 3T: an in-plane 2.0 x 2.0 mm2 with section thickness of 3.0 mm and a 2 mm3 isovolumetric voxel, neither had an inter-section gap. We used a multi-band DTI acquisi-tion with fat-suppressed single-shot spin-echo echo-planar sequence (20 non-collinear directions; b-values of 0 and 600 sec/mm2). The MR vendor-provided a commercially available DL model applied with 75% noise reduction settings to same subject DTI sequences at different spatial res-olutions. We compared DTI tract metrics from both DL-reconstructed scans and non-denoised scans for femur and tibia, at each spatial resolution. Differences were evaluated using Wilcox-on-signed ranked test and Bland-Altman plots. When comparing DL versus non-denoised diffu-sion metrics in femur and tibia using the 2 mm x 2mm x 3 mm voxel dimension there were no significant differences between tract count (p = 0.1, p =0.14) tract volume (p = 0.14, p = 0.29), or tibial tract length (p=0.16); femur tract length exhibited a significant difference (p

: Innovative solutions are now being researched to manage the ever-increasing amount of data required to optimize the performance of internal combustion engines. Machine Learning ap-proaches have shown to be a valuable tool for signal prediction due to their real-time and cost-effective deployment. Among them, the architecture consisting of Long Short-Term Memory (LSTM) and one-dimensional Convolutional Neural Networks (1DCNN) has emerged as a highly promising and effective option for replacing the role of physical sensors. The architecture com-bines the capacity of LSTM to detect patterns and relationships in smaller segments of the signal with the ability of 1DCNN to detect patterns and relationships in larger segments of the signal. The purpose of this work is to assess the feasibility of substituting a physical device dedicated to calculating the torque supplied by a spark-ignition engine. The suggested architecture was trained and tested using signals from the field during a test campaign conducted under transient operating conditions. The results reveal that LSTM+1DCNN is particularly well suited for signal prediction with considerable variability. It constantly outperforms other architectures used for comparison, with average error percentages of less than 2%, proving the architecture's ability to replace physical sensors.

This study evaluated the mechanical strengths of three types of orthodontic micro-implants by analyzing their structural configurations. Thirty micro-implants of three types (diameter 1.5 mm, Types A, B, C) were assessed. All micro-implants were manually driven into artificial bones at an 8-mm depth. The insertion torque (IT), pullout strength (PS), and gripping volume (GV) of each type were measured. Intergroup comparisons and intragroup correlation were investigated by statistical analysis. Type B had the greatest inner–outer diameter ratio (0.67), and Type A had the smallest (0.53). The IT of Type A (5.26 Ncm) was significantly (p = 0.038) lower than that of Type C (8.8 Ncm). There was no significant difference in the pullout strength (p = 0.868). The GV of Type A (9.7 mm3) was significant (p < 0.01) greater than Type C (8.4 mm3). Type C was significant (p < 0.01) greater than Type B (7.2 mm3). Spearman’s rho rank correlation test showed that PS of Type B was correlated significantly with GV. In conclusion, the design of thread and its GV were the important factors on the mechanical strengths of micro-implant.

Gamma titanium aluminides (γ-TiAl) present an excellent behaviour under high temperature conditions, being a feasible alternative to nickel-based superalloy components in aeroengine sector. However, considered as a difficult to cut material, process cutting parameters require special study to guarantee components quality. In this work, developed drilling mechanistic model is a useful tool in order to predict drilling force (F_z) and torque (T_c) for optimal drilling conditions determination. The model is validated for three types of Gamma-TiAl alloys. Integral hard metal end-drilling tools and different cutting parameters (feeds and cutting speeds) are tested in three different sized holes for each alloy.

The application of non-uniform spiral gratings to control structure, topological parameters and propagation of orbital angular momentum (OAM) beams was studied experimentally with coherent near-infrared light. Adapted digital spiral grating structures were programmed into the phase map of a high-resolution liquid-crystal-on-silicon spatial light modulator (LCoS-SLM). It is shown that characteristic spatio-spectral anomalies related to Gouy phase shift can be used as pointers to quantify rotational beam properties. Depending on sign and gradient of spatially variable periods of chirped spiral gratings (CSG), variations of rotation angle and angular velocity as a function of propagation distance were measured. Propagation-dependent self-torque is introduced in analogy to known local self-torque phenomena of OAM beams as obtained by the superposition of temporally chirped or phase modulated wavepackets.

Increased definite power, reduced cost, and dynamic construction are the important features required by electric motors for various applications. One such motor accommodating all the requisites mentioned above is Switched reluctance. Applications pertaining to small, commercial, and EV find Switched reluctance machine as a developing competitor to the conventional induction and permanent magnet motors. Though SRMS contribute a considerable number of advantages over induction motors and permanent magnet motors, the primary disadvantages pertaining to SRMs are the torque ripple, especially at high-speed operation, and the resulting acoustic noise. These disadvantages may not always be detrimental to the systems in entirely all cases, but depending on the application to be employed, torque ripple and acoustic noise form are detrimental to the system. This paper reviews the technology status and recent trends in the minimization of torque ripples switched reluctance machines.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

This paper will present the torque control design of an AFPMSM, one stator, and one rotor, using an FLC and ANFIS in-wheels fed by a three-level T-type inverter. The Surgeon ambiguous inference file of the FLC controller is built by two input vectors, the stator current error and the derivative of the stator error. These input variables include five membership functions, Negative big (NB), Negative small (NS), Equal zero (ZE), Positive small (PS), and Positive big (PB). The FLC controller is implemented with a 5x5 matrix so that the output stator voltage of the controller is required. The ANFIS controller for the neural network-based feature set and the fuzzy system. The neural network develops the dataset on the stator current error (e) and error integral (∆e). Then, the generated dataset is fed to the fuzzy logic method, and the control rules are developed. This ANFIS controller is caused by the training and testing phases. Finally, the FLC and ANFIS torque controllers are compared with the PI controller. The correctness of the proposed control structured solution is demonstrated by the simulation results of MATLAB/SIMULINK.

Typically, a diesel generator on the merchant ship, composed of a wound rotor synchronous generator and a four-stroke diesel engine, supplies electrical power to various loads. Recently, shaft generators for merchant vessels are increasingly replacing diesel generators to reduce CO2 emissions through fuel efficiency improvement. In particular, permanent magnet generators replace induction generators due to their high-efficiency characteristics at light loads. The surface-mounted permanent magnet can be a suitable rotor topology due to the relatively short constant power range. This generator can also operate as a motor according to the propulsion mode, so minimizing the harmonics of the induced voltage and the torque ripple is necessary. This paper proposes an alternative NdFeB magnet pole topology combined with the modular step-skewed rotor. The step-skewed rotor affects to reduce higher-order harmonics, and the modular pole reduces the permanent magnet assembly process and harmonics in voltage and torque. A 2-D finite element method is used to evaluate the harmonics of induced voltage and torque pulsation for the proposed topology. The topology shows harmonic minimization effect by comparing the characteristics of three flatted-bottom magnets. Compared to the tapered bread-loaf magnet, voltage harmonics to the 100th component are almost the same, and the torque ripple is reduced by more than 12% at the same residual flux density. The analysis method is verified by comparing test and analysis results for prototype machines with similar specifications.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

This article presents a harmonic analysis of the stator currents of a squirrel-cage in-15 duction motor fed by a voltage source inverter with PWM space vector control (SV-PWM). The 16 influence of PWM switching frequency and dead time (dead-band) of controlled transistors on 17 THD and electromagnetic torque ripple is shown. The aim is to determine the lowest switching 18 frequency of the transistors for which the drive will operate correctly. Characteristics were de-19 termined as functions in the form of THD ( ), where the least square approximation was 20 used for stator current measurements when the PWM switching frequency is changed. The ap-21 proximations were realized for simulation and experimental results. To clarify the results, the 22 operation of hardware PWM circuits in microcontrollers was analyzed.

The aim of the study is to investigate the effects of artificial aging by thermocycling and mechanical loading on force/torque delivery by thermoplastic orthodontic aligners. Ten thermoformed aligners made of Zendura™ thermoplastic polyurethane sheets were aged over two weeks in deionized water by thermocycling alone (n=5) and by both thermocycling and mechanical loading (n=5). The force/torque generated on upper second premolar (Tooth 25) of a plastic model was measured before aging (as control), and after 2, 4, 6, 10, and 14 days of aging, using a biomechanical set-up. Before aging, the extrusion-intrusion forces were in the range of 2.4 to 3.0 N, the oro-vestibular forces were 1.8 to 2.0 N, and the torques on mesio-distal rotation were 13.6 to 40.0 Nmm. Pure thermocycling had no significant effect on the force decay of the aligners. However, there was a significant decrease in force/torque after 2 days of aging for both thermocycling and mechanical loading aging group, which is no longer significant over 14 days of aging. In conclusion, artificial aging of aligners in deionized water with thermocycling and mechanical loading results in a significant decrease in force/torque generation. However, the mechanical loading of aligners has a greater impact than thermocycling alone.

Abstract: This study investigates the effect of Electric Vehicle Charging Stations (EVCS) on light-duty Electric Vehicle sales and the Total California rebates. Electric Vehicle Charging Stations (EVCS) are infrastructure facilities that allow for the charging of electric vehicles (EVs). I applied the before and after model with California state county using its community-level attributes and used the difference-in-difference design to identify a strategy for estimating the causal effects of these attributes. These attributes include EVCS installations by time, EV sales by time, rebate applications by time, the number of multi-unit housing units, and the median income levels. The empirical ev-idence of this study shows the estimated relationship between public EV charging installation and EV sales overall by community income level, housing density, and other relevant factors, the result shows that EVCSs is highly correlated with light duty Electric Vehicle adoption. For the investors, policymakers, and other stakeholders, this study provides evidence of a threshold of EVCS on Light Duty Electric Vehicle adoption and rebate in California.

In this paper, the design process of BLDC adopting the dual rotor method that can reduce the overall size of the motor while generating the same torque as the conventional Permanent Magnet BLDC is analyzed. A simple size is selected by obtaining the torque per rotor volume (TRV), and a method of matching the counter electromotive force by selecting the pole arc of the magnet through a magnetic equivalent circuit is analyzed. Since the efficiency is low because the 120-degree commutation method is selected, the middle stator is optimized through detailed design through the experimental design method. Afterwards, it has the advantage of being able to shift without stopping due to the characteristic of a dual rotor. For this, an analysis of the driving characteristics for each mode is performed.

Transitioning to clean cooking fuels is not only part of achieving SDG7, but also makes a significant contribution to mitigating climate change by reducing carbon emissions. The paper contradicts the conventional wisdom that electricity is too expensive to cook with. The paper explores the energy required to cook dishes using different technologies and fuels by analysing data from Cooking Diaries and Controlled Cooking tests conducted under the MECS programme. Electric pressure cookers (EPCs) use least energy when compared with electric hotplates, and a detailed description of how the EPC works explains why this should be. The paper draws out distinctions between African and Asian dishes, notably the impact of energy intensive dishes prepared mostly in Africa. Standard efficiency based approaches to comparing the performance of stoves are not appropriate to modern electric cooking devices so an alternative approach based on specific energy consumptions is proposed e.g. charcoal stoves use 15 times as much energy as EPCs to cook African dishes. Energy ratios provide a basis for estimating carbon emission reductions associated with transitioning to modern cooking fuels. Historical costs show that the cost of cooking with an EPC can be only 20% of the cost of cooking with charcoal, which highlights the potential for modern, energy efficient electric cooking devices to defy the conventional wisdom of the energy ladder.

Researchers achieved high torque volume ratios in magnetorheological (MR) fluid braking devices by introducing multiple layers and multiple poles concepts. The number of magnetic poles, pole geometry and placement have a significant effect on these multi-pole MR brake performances. This research work focused on the effect of the pole head geometry in a multi-pole dual-disc MR brake for the enhancement of braking torque. The magnetic field generated by the electromagnetic coil has to penetrate through pole heads and travel orthogonally through the rotor and MR fluid layers to achieve maximum brake torque. This flow depends on the profiles of the magnetic pole head area and corresponding core dimensions. This study considered pentagon, square, hexagon, trapezoid and ellipse pole head profiles in place of the conventional circular pole and the best possible core dimensions were used for each geometry. A three-dimensional electromagnetic analysis of the MR brake is conducted to simulate the brake performance. Results showed that the hexagonal and elliptical pole heads are having better magnetic field area, magnetic intensity distribution and higher magnetic flux lines piercing through the MR fluid perpendicularly than the circular and square pole heads. An increment of 3.88% for braking torque performance is obtained, and the braking torque is significantly enhanced.

Cogging torque is a pulsating, parasitic and undesired torque ripple intrinsic of the design of a permanent magnet synchronous generator (PMSG), which should be minimized due to its adverse effects: vibration and noise. In addition, as aerodynamic power is low during start-up at low wind speeds in small wind energy systems, the cogging torque must be as low as possible to achieve a low cut-in speed. A novel mitigation technique using compound pre-slotting, based on a combination of magnetic and non-magnetic materials, is investigated. The finite element technique is used to calculate the cogging torque of a real PMSG design for a small wind turbine, with and without using compound pre-slotting. The results show that cogging torque can be reduced by a factor of 48% with this technique, while avoiding the main drawback of the conventional pre-slotting technique: the reduction of induced voltage due to leakage flux between stator teeth. Furthermore, through a combination of pre-slotting and other cogging torque optimization techniques, 84%, cogging torque can be eliminated for a given design.

The aim of this study is to study the effect of aging in different media (deionized water and artificial saliva) on the force/torque generation by thermoplastic orthodontic aligners. Ten thermoformed aligners made of Essix ACE® thermoplastic sheets were aged in deionized water and in artificial saliva over two weeks at 37 C, five in each medium. The force/torque generated on upper second premolar (Tooth 25) of a resin model was measured at day 0 (before aging), 2, 4, 6, 10, and 14, using a biomechanical test set-up. The results showed that the thermocycling of aligners has no significant impact on their force/torque decay. No significant differences were also found in force/torque between the aligners stored in deionized water nor artificial saliva. The vertical extrusion-intrusion forces were measured in the range of 1.4 to 4.6 N, the horizontal oro-vestibular forces were 1.3 to 2.5 N, while the torques on mesio-distal rotation were 5.4 to 41.7 Nmm. It could be concluded that the influence of saliva on the mechanical properties can be classified as insignificant, and no significant difference between artificial aging in deionized water or artificial saliva was observed.

The aim of this study was to compare the screw removal torque of mini conical prosthetic components and straight trunnion of indexed morse taper implants, after mechanical cycling. The sample consisted of 40 implants and 20 mini-conical prosthetic components (MC group) and 20 straight trunnion components (ST group). Each group consisted of 10 specimens, with 2 implants in each, and cobalt-chromium metallic crowns were screwed into each sample. The components of the MC group received a torque of 20 N.cm with a digital torque wrench and after 10 minutes were retightened with the same value as the initial torque. The components of the ST group received a torque of 30 N.cm, with a digital torque wrench and after 10 minutes, they were retightened with the same value. The screws of the respective crowns of the two groups received a torque of 10 N.cm and after 10 minutes were retightened with the same value. Each group was subjected to the fatigue test in a mechanical cycler at 2.000.000 cycles, with a load of 250 N and frequency of 4 Hz. At the end of the fatigue test, the loosening torque of each screw of the specimens was measured through a digital torque wrench. The data were analyzed by two-way ANOVA and Tukey test. In both groups, there were loss of torque. The results showed no statistic difference between MC and ST groups.

Among earth’s microbial populations are the genes, functional capacities, generational memory and sentient cognition that enable microorganisms to adapt and thrive in the full range of ecological conditions found on planet earth. In prior sequential publications, we considered fundamental properties (e.g., use of and responses to sound, light, vibrations) and features of microorganisms that cause them to be critical co-partners of human and other holobionts as well as the potential benefits for humanity that can be gained by fully applying quantum-related and novel capacities of microbial life. In this narrative review we: 1) discuss key concepts concerning a microbially-enhanced and sustainable future, and 2) focus on electric- and magnetic- based features of microorganisms that make them pivotal for myriad benefits ranging from beyond pharma-based health and wellness to free- and/or renewable energy and restorative agriculture to improved human networking. While the benefits are many, the risks posed by hazardous electric or magnetic field exposures to both holobionts and microbial communities are significant. This review concludes that microbes and their remarkable capacities offer both humanity and the planet a much brighter future if we reverse the demonization of microbes and wanton microbiome degradation that has predominated much of the past century.

In this paper, a small wind power generator is proposed with a new straight shape stator and rotor. The advantages of the proposed structure are introduced through a comparison between the basic and the proposed models. By comparing the pole slot combination of the proposed generator, the combination with optimal cogging torque characteristics was selected. The electromagnetic characteristics of proposed shape are analyzed for design variables using a finite element analysis (FEA) of ANSYS Maxwell. The final model of the proposed structure is designed by considering cogging torque and the generator electromagnetic characteristics. The electromagnetic and structural simulations of the final model are performed to satisfy the required performance of generator and mechanical safety. To verify the FEA results of the final model, a prototype is manufactured, experimented, and compared with the FEA results.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

The high figure of merit and earth abundance of Cu₁₂Sb₄S₁₃ thermoelectric ma- terials have recently attracted many attentions toward these type of complex compounds. Intrinsic low thermal conductivity, as well as tunable electronic transport properties, make them suitable for thermoelectric power generation. In this study, we perform a comparative theoretical study on the substituted compounds, primarily at the Cu site including known tetrahedrite Cu₁₂Sb₄S₁₃, by means of first-principles calculations. The density functional theory of electric structure is applied to investigate the result of substitution.

In steel recycling, the optimization of electric arc furnaces (EAFs) is of central importance in order to increase efficiency and reduce costs. This study focuses on the optimization of electric arcs, which make a significant contribution to the energy consumption of EAFs. A three-phase equivalent circuit integrated with the Cassie-Mayr arc model is used to capture the nonlinear and dynamic characteristics of arcs, including arc breakage and ignition process. A particle swarm optimization technique is applied to real EAF data containing current and voltage measurements to estimate the parameters of the Cassie-Mayr model. A novel Arc Quality Index (AQI) is introduced in the study, which can be used to evaluate arc quality based on deviations from optimal conditions. The AQI provides a qualitative assessment of arc quality, analogous to indices such as arc coverage and arc stability. The study concludes that the AQI serves as an effective operational tool for EAF operators to optimize production and increase the efficiency and sustainability of steel production. The results underline the importance of understanding electric arc dynamics for the development of EAF technology.

Background and Objectives: Mechanical and biological complications can lead to system fracture or screw loss on dental implants. Narrow and regular platforms have been used without a consensus about the effect of distance the abutment from the prosthetic platform margin. The aim of this study is to evaluate different insertion torques in the deformation of tri-channel platform connections through two- and three-dimensional measurements with micro-CT. Materials and Methods: 164 implants were divided into groups (platform diameter and type): 3.5, 3.75, and 4.3 mm NP (Narrow Platform), and 4.3 mm RP (Regular Platform). Each implant-platform group was then divided into four subgroups (n = 10) with different torques: T45 (45 Ncm), T80 (80 Ncm), T120 (120 Ncm) and T150 (150 Ncm). The implant-abutment-screw assemblies were scanned and the images obtained were analyzed. Results: A significant difference was observed for the linear and volume measures between the different platforms (p &lt;0.01) and the different implant insertion torques (p &lt;0.01). Qualitative analysis suggested higher deformation resistance for the 3.75 NP compared to the 3.5 NP, and RP was more resistant compared to the NP. Conclusions: The 0.25-mm increment in the implant platform did not increase the resistance to the applied insertion torques; the 4.3-mm implant was significantly stronger compared to the 3.5-mm implant and the proposed micro-CT analysis was considered valid for both 2D and 3D analyses of micro gaps, qualitatively and quantitatively.

This study aimed to investigate the effects of forearm postures and elbow joint angles on muscle torque and mechanomyography (MMG) signals. The torque about the elbow and MMG of the biceps brachii (BB) muscle were measured in 36 healthy subjects using an in-house elbow flexion testbed and Neuromuscular electrical stimulation (NMES) of the BB muscle. The BB muscle received stimulation intensity while the forearm was positioned in the neutral, pronation or supination. The elbow was flexed at angles 10°, 30°, 60° and 90°. (0° = full elbow extension). The study analyzed the impact of forearm posture(s) and elbow joint angle(s) on the root mean square value of torque (TQ_RMS). Subsequently, MMG parameters such as the root mean square value (MMG_RMS), the mean power frequency (MMG_MPF), and the median frequency (MMG_MDF), were analyzed in the longitudinal, lateral, and transverse axes of the BB muscle fibers. Forearm posture and elbow flexion angle were found to significantly influence TQ_RMS (P < 0.05). Similarly, MMG_RMS, MMG_MPF and MMG_MDF exhibited a significant difference for all postures and angles (P < 0.05). However, the combined main effect of forearm postures and elbow joint angles was insignificant in the longitudinal axis (P > 0.05). The study also found that MMG_RMS and TQ_RMS increased with the joint angle to 60° and decreased to the other angle(s). However, during this investigation,MMG_MPF and MMG_MDF exhibited a consistent decrease in response to joint angles. This finding suggests that the muscle contraction evoked by NMES may be influenced by the interplay between actin and myosin filaments, which are responsible for muscle contraction and are in turn influenced by muscle length. As restoring the function of limbs is a common goal in rehabilitation services, it becomes imperative to develop methods that may enable the real-time tracking of exact muscle dimensional changes and activation levels.

Electromobility has gained significant attention in the auto- motive industry, with car manufacturers striving to improve the charging experience for their users. In this study, we compare multiple realistic charging strategies in order to quantify the benefits arising from better planning of charging sessions. We base our evaluation on electricity price data from three regions: Sweden (SE3 region), Germany (DE region), and Denmark (DK2 region). This data is obtained from the ENTSO-E Transparency Platform, covering the two full years 2021 and 2022. We enhance this dataset with commercial price forecasts from the company StormGeo and benchmark it against a naive forecasting method. The primary aim of our work is to compare how the strategies of varying levels of complexity perform across the three different countries in terms of minimizing energy costs for electric car users.

The widespread adoption of electromobility constitutes one of the measures designed to reduce air pollution caused by traditional fossil fuels. However, several factors are currently impending this process, ranging from insufficient charging infrastructure, battery capacity, long queueing and charging time, to psychological factors. On top of range anxiety, the frustration of the EV drivers is further fueled by the lack the uncertainty of finding an available charging point on their route. To address this issue, we propose a solution that comes to bypass the limitations of the Reserve now function of the OCPP standard, enabling drivers to make charging reservations for the upcoming days, especially when planning a longer trip. We created an algorithm that generates reservation intervals based on the charging station's reservation and transaction history. Subsequently, we ran a series of test cases that yielded promising results, with no overlapping reservations.

Abstract: Recent years demonstrate the increased attention to radon from two scientific directions. After neglecting radon as earthquake precursors in 1990-th it becomes again the subject of earthquake-forecast papers discussions due to growing networks of the radon monitoring in different countries, especially, the technologies of real-time radon measurements where the gamma-spectrometers become the leader of interest as the sources of 222Rn identification. The second fast developing direction is including the radon in the Lithosphere-Atmosphere-Ionosphere Coupling (LAIC) models as a source of the boundary layer ionization. And here we encounter with second direction which is not connected with the earthquake forecast problems. It is the role of air ionization by radon as a source of the Global Electric Circuit (GEC) modification. In this publication we try to unite all these problems to present more complex view on radon as important element of our environment.

Transportation electrification has been identified as a crucial shift to be made for achieving energy security and emission reduction targets. Electric Vehicles (EVs) play a significant role in achieving these targets; therefore, there is a growing trend to develop new EV technologies and associated infrastructure. Along with these developments, EVs' Quality of Service (QoS) aspects should be enhanced to increase the number of EVs on the road. Various QoS factors are defined to assess the QoS of EVs, and one of the two aims of this paper is to provide a comprehensive review of these factors. The other aim is to review recent developments of associated communication technologies which are essential for exchanging information between EVs and charging stations. This paper serves as a comprehensive review and useful reference for researchers working on QoS aspects of EVs and associated communication systems aiming to enhance the QoS.

Appling the controlling relative permittivity and permeability in the equations for the gravitational-magnetic-electric field interaction, a very large variation of the gravitational acceleration of the Earth by electric/magnetic field could be arrived at. This conclusion may be supported by some of the experiments for the gravitational effect of superconductivity.

Measuring the non-pathogenic Torque Teno Virus (TTV) load allows assessing the net immunosuppressive state after kidney transplantation (KTx). Currently, it is not known how exposure to maintenance immunosuppression affects TTV load. We hypothesized that TTV load is associated with the exposure to mycophenolic acid (MPA) and tacrolimus. We performed a prospective study including 54 consecutive KTx. Blood TTV load was measured by an in-house PCR at months 1 and 3. Together with doses and trough blood levels of tacrolimus and MPA, we calculate the coefficient of variability (CV), time in therapeutic range (TTR) and concentration/dose ratio (C/D) of tacrolimus, and the MPA-area under the curve (AUC-MPA) at the third month. TTV load at the first and third month discriminated those patients at risk of developing opportunistic infections between months 1 and 3 (AUC-ROC 0.723, 95%CI 0.559-0.905, p = 0.023) and between months 3 to 6 (AUC-ROC 0.778, 95%CI 0.599-0.957, p = 0.028), respectively, but not those at risk of acute rejection. TTV load did not relate to mean tacrolimus blood level, CV, TTR, C/D and AUC-MPA. To conclude, although TTV is a useful marker of net immunosuppressive status after KTx, it is not related to exposure to maintenance immunosuppression.

In this paper we give the improved and new analytical and semi-analytical expression for calcu-lating the magnetic vector potential, magnetic field, magnetic force, mutual inductance, torque, and stiffness between two inclined current-carrying arc segments in air. The expressions are ob-tained either in the analytical form over the incomplete elliptic integrals of the first and the sec-ond time or by the single numerical integration of some elliptical integrals of the first and the second kind. The validity of the presented formulas is proved from the special cases when the inclined circular loops are treated. We mention that all formulas are obtain by the integral ap-proach except the stiffness which is found by the derivative of the magnetic force.

Early in the middle of the 1800s. Up until about 1900, the automotive land speed record 1 was held by an electrical vehicle. Unfortunately, internal combustion engine vehicles did not do 2 well in the market due to their high cost, limited speed, and short range in the 20th century, which 3 resulted in a global fall in their use as private motor vehicles. Since there are no fuel emissions into 4 the environment, there are important uses for electrical vehicles, Electric cars, or EVs, have a closed 5 circuit, cheap operating costs, no maintenance requirements, and excellent performance. The goal 6 of this project is to assess the current state of electric vehicles and the issues surrounding the global 7 advancement of electric vehicle technology. Because of the changing climate.8

The rapid growth rate of the elderly population is a serious current issue in most countries, affecting them economically through needed medical treatment and healthcare planning. The priority concern is how to reduce the number of elderly people requiring long-term healthcare and raise the number who are able to live independently. This study executed a behavior assessment of elderly person’s self-reported use of electric scooters and analyzed their degree of acceptance of these assisted living tools, partly through a related factor analysis of our survey instrument. We used this questionnaire survey as our research method, applying SPSS22 software for factor analysis that revealed five survey facets.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

Today, there are commercially available high-performance electric wheelchairs, capa-ble of responding to strong limitations. However, despite these advancements, there is a significant portion of the population with severe disabilities who cannot access this mobility solution due to safety reasons. Indeed, either due to motor issues preventing reliable control of the wheelchair's commands, or associated visual or cognitive pathologies, the use of an electric wheelchair by these individuals would put them at risk and could also constitute a danger to those around them. This is why our research team is working on the development of augmented wheelchairs that allow a greater autonomy. We are mainly developing a system compatible with all electric wheel-chairs on the market, capable of making them anti-collision and anti-fall on uneven ground (sidewalks, stairs, etc.). In this article, we present our solution regarding the anti-collision function, in particular the sensors used to do this, as well as the strategy. We will focus on the shortcomings and weaknesses of various types of sensors and demonstrate how, by combining them in a certain way, we can develop a collision avoidance device capable of managing the diversity of everyday life situations. The two types of sensors that will be combined here are an in-house developed special near infrared sensor from the laboratory and a commercially available ultrasonic sensor. We will present the internal operation of the sensors, their limitations, experimental tests involving integration with the wheelchair, and the structure of the complete device.

The thermal degradation of brakes has a significant impact on the stability of pure electric commercial vehicles during long downhill braking. Based on road slope and using fuzzy control method, design strategies for motor regenerative braking force and friction braking force distribution, with the aim of reducing friction braking force, improving braking stability, and recovering braking energy. By establishing driving conditions on roads with different slopes and using numerical analysis methods to verify the proposed control strategy. the results show that under the 6% constant slope driving condition, the vehicle maintains a constant speed of 30km/h downhill driving, and the braking energy recovery rate reaches 50.93%; Under the condition of 3% -6% gradient driving, the vehicle speed fluctuates slightly, but it can still be maintained at a constant speed of 30km/h for downhill driving through the adjustment of the motor's reverse drag characteristic, with a braking energy recovery rate of 49.97%; During the process of driving downhill at a constant speed, the frictional braking force does not participate in braking; The braking energy recovery rate is determined by the slope and braking deceleration.

In this non-exhaustive review, we discuss the importance of invariant vectors in atomic physics, such as the Laplace-Runge-Lenz vector, the Redmond vector in the presence of an electric field, the Landau-Avron-Sivardière vector when the system is subject to a magnetic field, and the supergeneralized Runge-Lenz vector for the two-center problem. Application to Stark and Zeeman effects are outlined. The existence of constants of motion in the charge-dyon system is also briefly mentioned.

Bacteria play a key role in both human health and disease. One of the most prevalent harmful bacteria is E. coli which is responsible for several illnesses ranging from diarrhea, stomach cramp and fever. In this work we explore the application of moderate electric or magnetic fields for treating deionized water that is contaminated with E. coli. We found that moderate alternating electric (AC) fields (10 V/cm to 1kV/cm) and moderate static magnetic fields (10 to 65 mT) can significantly inactivate E. coli by up to 90% or more. This provides the possibilities of developing a low cost and a practical bacteria inactivation technique using electric or magnetic fields.

Recently, due to the decrease in labor force, increase in labor costs, and the desire for improved quality of life, research on robots has been actively conducted to address these issues. However, it is currently difficult to find robots that physically interact with humans. The reason is that the actuators of robots do not have high torque density on their own. To solve this problem, high torque density motors, such as proprioceptive actuators, are being researched. However, the torque density is still insufficient for physical interaction with humans, so we have developed a motor with higher torque density. However, high torque density motors have the disadvantage of lower speed characteristics due to increased Back-EMF. Therefore, to address the deterioration of speed characteristics in the developed motor, we applied the Independent 3-Phase winding structure to improve the speed characteristics. Consequently, through comparison with Y-Connection and Delta-Connection, we propose the most suitable winding structure for high torque density motors intended for physical interaction with humans.

In this paper, a two-link manipulator system stability performance is designed and analyzed using Optimal control technique. The manipulator system is highly nonlinear and unstable. The system is modelled using Lagrangian equation and linearized in upward unstable position. The closed loop system is designed using optimal sliding mode controller. The system is compared with a known PID controller with an impulse applied and disturbance torques and a promising results has been obtained.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

This article presents a novel approach to understanding the influence of electric Energy on space-time curvature. EFE actual calculations refer solely to gravitational charges. In this article, I expand them to include the electric charge with calculations carried specifically for electric charges, with exciting results. The article leverages the universal consistency of physical laws, applying the known effects of gravitational charges on space-time curvature to electric charges. The research focuses on calculating the specific impact of electric charges on space-time curvature, rooted in the principle that space-time curvature is omnipresent. The findings reveal that space-time curvature's alteration due to an electric charge is influenced by various factors, including the charge's location, magnitude, mass, density, associated electric field, and its motion through space-time. Notably, the conversion factor for electric charges differs from the conversion factor for gravitational charges. These insights significantly enhance our understanding of electromagnetism and general relativity, paving the way for a more profound comprehension of electric charges.

An embryonic version of membrane theory can be date back to the Bernstein's work reported more than a hundred years ago. Such an originally old work has evolved conceptually and mathematically up until today, and it plays a central role in current membrane theory. Goldman-Hodgkin-Katz equation (GHK eq.) is one of the math-based monumental works, which constitutes the present membrane theory. Goldman theoretically derived GHK eq., but its physiological meaning was provided by the two renowned scientists, Hodgkin and Katz. These two employed an assumption that the electric field (EF) across the plasma membrane is constant to validate the GHK eq. physiologically. Proposal of Hodgkin-Huxley model (HH model) is another math-based monumental works developed from the membrane theory and now forms a fundamental part of the current membrane theory. GHK eq. and HH model are quite fundamental central concepts in the current physiology. Despite the broad acceptance of GHK eq. at present time, its prerequisite that the EF within the plasma membrane is constant is hardly believable. Especially when the action potential is generated, it sounds totally nonsense. Furthermore, the existence of constant EF within the plasma membrane is conceptually almost in conflict with the HH model. The authors will discuss those problematic issues the membrane theory inherits.

This paper provides a proof of concept for a linear electric generator that can be used to harvest energy from various sources of linear motion, such as vibrations, free-piston engines and wave energy. The generator can be used to power small electronic devices, such as sensors, or charge household batteries. Literature was reviewed to develop an understanding about the applications, control methods, excitation methods and mechanics of rotating and linear electric machines. A bidirectional, two-sided linear machine was designed with two stator cores and a single mover core. The stator windings and mover winding can be independently excited, allowing for three modes: no mover excitation, DC excited mover, and AC excited mover. Simulations results showed that the magnetic flux generated by DC excited stator cores were concentrated in the centre of the mover core. The use of two stator cores eliminates lateral flux in the mover core when it is not excited, minimising attraction and repulsion forces. Parametric analysis showed that flux cutting occurred in all operation modes, verifying that the generator will produce power when operating. Hardware tests produced an output current when the machine is electrically and mechanically excited, verifying the proposed design.

To ensure sustainability of the future power grid, the rate of expansion of distributed renewable energy resources (DRER) has introduced operational challenges. These includes managing transmission constraints with DRER power injection, dispatching DRER efficiently, managing system frequency and ensuring sufficient reactive power for voltage support. Coupled with the intensification of wildfires, power infrastructure across the United States faces challenges to minimize the impact to maintain system reliability and resiliency. This research embarks on a comprehensive evaluation, beginning with an in-depth historical analysis to delineate regions most susceptible to wildfires. Utilizing a multidimensional approach, the study assesses wildfire-induced risks to power grids, by integrating historical wildfire occurrences, real-time wildfire proximities, Moderate Resolution Imaging Spectroradiometer (MODIS) derived vegetation metrics, and system parameters, by employing Principal Component Analysis (PCA) based optimal weights, leading to the formulation of a novel risk factor model. This risk factor has the potential to be the key to ensuring the resilience of a renewable-rich smart grid when faced with a severe weather event. Our model’s applicability was further verified through an empirical assessment, selecting representative networks from diverse regions, providing insights into the geographical variability of risk factors. Ultimately, this study offers stakeholders and policymakers a comprehensive tool-set, empowering decisions regarding infrastructure investments, grid reinforcements, and strategic power rerouting to ensure consistent energy delivery using risk assessment against wildfire.

Recently, Electric Two-Wheelers ETW are changing the face of the global automotive market. This study focused on selecting proper material and mechanical isolation gap to design a protective enclosure for the battery pack of ETW. The integration of the Failure, Modes, Mechanism and Effect Analysis (FMMEA) method is utilized to develop the interface matrix and the severity index of different components of the enclosure. By analyzing different forces from the road conditions, dynamics during turn, acceleration, and deceleration with the enclosure, it becomes a crucial load-bearing element. Employing Finite Element Modeling (FEM), structural strength using materials like AL6061, Q235, C22000, DC 01 and Teflon are assessed under varying static, dynamic and thermal conditions. Modal analysis is conducted to observe the excitation frequencies where the maximum deformation for the metal enclosure is observed beyond 500Hz. AL6061 material that can withstand the stresses and deformations that are under allowable stress limits with negligible deformation is most preferable material based on the results. Minimal of 2.5 mm gap to be provided in case of metal casing and 10mm in case of Teflon is proven.

The transportation sector is seeing an increased adoption rate of electric vehicles (EV), which comprise battery electric vehicles (BEV), hybrid electric vehicles (HEV) and plug-in hybrid electric vehicles (PHEV). This mode of transportation is likely to displace automobiles powered by internal combustion engines (ICE) in the nearest future, as indicated by the current trend. Each of the key EC components is home to a variety of technologies that are either currently in use or will be in the near future. Electric vehicles have the potential to have a significant impact on a variety of fields, including the economy, the energy infrastructure, and the natural environment. As a result of the production of carbon dioxide gas from the combustion of fossil fuels, transportation is the sector that is responsible for the second-highest amount of greenhouse gas emissions. Electric vehicles, often known as EVs, are getting a lot of attention as a potentially game-changing solution to this issue. It is possible for electric vehicles to produce fewer emissions of carbon dioxide (CO2) than conventional automobiles due to the fact that an electric motor serves as the vehicle's propeller rather than an internal combustion engine. EVs have the potential to become zero-emission vehicles if they are paired with renewable energy sources. This document presents an overview of the numerous types of EV drive circuits, covering their design as well as the benefits and drawbacks associated with each type. The current state of battery technology, particularly that pertaining to the batteries utilized in electronic vehicles, is discussed in this paper. This article also discusses electric motor efficiency, power density, fault tolerance, dependability, cost, and the best electric motor for EVs. Then, a thorough study of future EV implementation's obstacles and prospects is done. Charging times and battery performance are examples of technological challenges, but government regulation of EVs continues to be a substantial non-technical hurdle.

We suggest a deep learning based sensor signal processing method to remove chemical, kinetic and electrical artifacts from ion selective electrodes’ measured values. An ISE is used to investigate the concentration of a specific ion from aqueous solution, by measuring the Nernst potential along the glass membrane. However, application of ISE on a mixture of multiple ion has some problem. First problem is a chemical artifact which is called ion interference effect. Electrically charged particles interact with each other and flows through the glass membrane of different ISEs. Second problem is the kinetic artifact caused by the movement of the liquid. Water molecules collide with the glass membrane causing abnormal peak values of voltage. The last artifact is the interference of ISEs. When multiple ISEs are dipped into same solution, one electrode’s signal emission interference voltage measurement of other electrodes. Therefore, an ISE is recommended to be applied on single-ion solution, without any other sensors applied at the same time. Deep learning approach can remove both 3 artifacts at the same time. The proposed method used 5 layers of artificial neural networks to regress correct signal to remove complex artifacts with one-shot calculation. Its MAPE was less than 1.8% and R² of regression was 0.997. A randomly chosen value of AI-processed data has MAPE less than 5% (p-value 0.016).

A full potential all-electron density functional method within generalized gradient approximation is used to investigate the electronic, elastic and transport properties of cubic copper sulphide and copper selenide. The electronic structure suggests metallic behavior with a zero energy band gap for both materials. Elastic property calculations suggest a stiff material with the bulk to shear modulus ratio of 0.35 and 0.44 for Cu2S and Cu2Se respectively. The transport properties were estimated using the Boltzmann transport approach. Seebeck coefficient, electrical conductivity, thermal conductivity, and power factor all suggest a potential p-type conductivity for Cu2S and n-type conductivity for Cu2Se.

With the continuous improvement and observable benefits of electric vehicles (EVs), major logistic companies are introducing more EVs into their conventional fleets. This gives rise to a new type of vehicle routing problem with mixed vehicles, where heterogeneous internal combustion vehicles (ICVs) and electric vehicles are considered in route planning. In addition, certain deliveries that are not efficient on any type of vehicles, are outsourced to third-party common carriers. In this paper, we define this problem as a mixed vehicle routing problem with common carriers (MVRPC). The objective of such problems is to minimize the transportation costs by considering routes with ICVs and EVs, the possibility of visiting recharging stations, outsourcing options, and drivers’ layover regulations. This variant of the vehicle routing problems has many practical applications, particularly in the design of long-haul transportation and last-mile delivery services. Effective MVRPC solutions play a key role in promoting the going Green image and optimally allocating resources. The problem has received limited attention in the literature likely because addressing all the needed aspects is especially challenging. To solve the large-scale problem, we develop a branch-and-cut pricing framework that relies on strong cuts and customized labeling algorithms. Numerical experiments highlight the effectiveness of our algorithm. This success can be attributed to tailored critical resources, dynamically bounded bidirectional labeling procedures, strong dominance criteria, and implementation strategies.

A preliminary study of a wind turbine design is carried out using a wind tunnel to obtain its aerodynamic characteristics. Utilization of data from the study to develop large-scale wind turbines requires further study. This paper aims to discuss the use of wind turbine data obtained from the wind tunnel measurements to estimate the characteristics of wind turbines that have field size. The torque of two small-scale turbines was measured inside the wind tunnel. The first small-scale turbine has a radius of 0.14 m and the second small turbine has a radius of 0.19 m. Torque measurement results from both turbines were analyzed using Buckingham π theorem to obtain a correlation between torsion and diameter variations. The obtained correlation equation is used to estimate the field measurement of turbine power with a radius of 1.2 m. The resulting correlation equation can be used to estimate the power generated by the turbine by the size of the field well in the operating area of the tip speed ratio of the turbine design.

The methods of Artificial Intelligence (AI) have been used in the planning and operation of power systems for more than 40 years. In recent years, due to the development of microprocessor and data storage technologies, the effectiveness of this use has greatly increased. This paper provides a systematic overview of the application of AI including the use of Machine Learning (ML) to the power system. The potential application areas are divided into four blocks and the classification matrix has been used for clustering the AI application tasks. Furthermore, the data acquisition methods for setting the parameters of AI and ML algorithms are presented and discussed in a systematic way considering the supervised and unsupervised learning methods. Based on this, three complex application examples: wind power generation forecasting, smart grid security as-sessment (using two methods), and automatic system fault detection are presented and discussed in detail. Summary and outlook conclude the paper.

It is well known that the photon trajectories follow a curved path in a gravitational field. We explore here the gravitational bending of electric field lines. It seems that the electric field lines of a charge, supported in a gravitational field, follow exactly the trajectories of photons emitted isotropically from a source situated at the charge location. From a detailed examination of the electrostatic field of a charge accelerated uniformly in the instantaneous rest frame, exploiting the strong principle of equivalence, one can determine the bending of the electric field lines of a charge in a gravitational field. The fraction of electric field lines crossing a surface, stationary above or below the charge in the gravitational field, is shown to be exactly similar to the fraction of photon trajectories, emitted from a source placed at the charge location, intersecting that surface. On the other hand, for a freely falling charge in the gravitational field there is no such bending of electric field lines. The field lines continue to extend in radial straight lines from the instantaneous 'present' position of the charge, as do the trajectories of photons streaming away from the instantaneous position of a freely falling source in the gravitational field. The electric field configuration of a freely falling charge in the gravitational field is shown to be exactly the same as that of a charge moving uniformly in an inertial frame with velocity equal to the instantaneous ``present'' velocity of the freely falling charge.

Origins of the time, mass, electric charges and magnetic monopoles are explained. The energies, electric charges and magnetic charges of the particles are defined as E = cDtDV and |q| = cDt = E/DV, and |q_m| = c²Dt, respectively, for the 3-D quantized spaces warped along the time axis direction of ct in the 4-D Euclidean space. The energy (or mass) and charges (or electric charges and magnetic charges) are the vectors along the time axis of ct in the 4-D Euclidean space. This new concept is closely connected to the wave function of the quantum mechanics. The electric charges, magnetic charges and energies have the property of the space direction independence. Magnetic monopoles (charges) are the force carrying bosons with the inside electric field time loop. Electric monopoles are the elementary fermions. Photon space fluctuations are explained with the quantized magnetic charges.

Nowadays, all the stakeholders, policy makers, regulators, aircraft designers, producers, operators, etc.) are intensively working on development of the aircraft with full electric and hybrid propulsion systems. However, the technical, technological constrains (like limit on accumulator energy density) require introducing a new approach to conceptual design of such aircraft. The new methods is based on energy and mass balance evaluation. This paper analyses the identified constrains; integrates the energy and mass balance equations into the preliminary definition and calculations of the aircraft performance. By this way, the technological constrains might be transferred into the limitation on the aircraft energy and mass breakdown, that initiates a new approach to aircraft conceptual design uses the knowledge based multidisciplinary optimization. The paper describes the developed methodology for conceptual design of aircraft. It show results of implementing this new development philosophy to conceptual design of a four-seat small electric/hybrid aircraft and a special hybrid cargo UAV. The discussion of the results including got by using the emerging and enabling new technologies and new methods and solutions (including for example distributed propulsion system, unconventional forms, morphing, biomimics, etc.), demonstrates the possible implementation of the new development philosophy, new approach to aircraft conceptual design.

The work aims to improve the battery performance in hybrid electric vehicles (HEVs) by reducing the vehicle speed. We develop a specific protocol for managing battery use and optimizing the energy consumption rate to achieve this goal. The protocol automatically controls the driving operation, avoiding incompatible driving patterns with energy-saving mode and performance improvement. The protocol is submitted to a simulation process to predict the energy rate lowering and battery performance enhancement. The proposed protocol applies to any hybrid electric vehicle type and route conditions since it uses vehicle mass, drag and rolling coefficients, and road slope as variable parameters to determine the minimum energy consumption rate. We run experimental tests to validate the simulation data and the proposed protocol. Furthermore, the protocol applies to variable starting vehicle speeds, from 10 to 50 km/h, corresponding to the current driving patterns, sport, normal, and eco, set up by car manufacturers. A reduction of 10% in vehicle speed in urban and peripheral routes achieves a minimum energy rate, enhancing battery management. Current vehicle speed shows a deviation from optimum management of 18% while applying the vehicle speed reduction limits the deviation to 0.2%. Experimental results show a good agreement with simulation data with 94% accuracy. We tested the protocol for urban and peripheral routes with maximum vehicle speed limits of 60 and 90 km/h.

This paper proposes an electric vehicle routing problem with considering states of charging stations and suggests solution strategies. Charging of electric vehicles is a main issue in the field of electric vehicle routing problem. There are many studies to find locations of charging stations, recharging functions for batteries of vehicles, and so on. However, states of charging stations significantly affect the routes of electric vehicles, which is not much explored. The states may include open or close of charging stations, occupied or empty of charging slots, and so on. This paper investigates how the states of charging stations are estimated and routing strategies are determined. We formulate a mixed integer programming model and suggest how to solve the problem with exact method. Numerical examples provide the optimal routing strategies of electric vehicles in the changing environments of the states of charging stations.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

The cell concentration measurement on a culture assay using bioimpedance is a very useful tool, but it is complex to translate impedance to cell concentration values. The purpose of this work is to find a method to obtain in real time the cell concentration values for a given cell-culture assay using an oscillator as the measurement circuit. From a basic cell-electrode model, enhanced models of the cell culture immersed in a saline solution (culture medium) can be derived. These models can be used in a fitting routine to real time estimation of the cell concentration in a cell culture, using the oscillation frequency and amplitude delivered by measurement circuits proposed by the authors. Based on real experimental data (frequency and amplitude of oscillations) obtained by connecting the cell culture to an oscillator as a load, the fitting routine is simulated, and real time data of cell concentration is achieved. These results are compared with concentration data found by traditional optical methods for counting. In addition, the error obtained is divided and analyzed in two parts: in the first part of the experiment (when the few cells are adapting to the culture medium) and the second part of the experiment (when the cells grow exponentially until they completely cover the well).Low error values are obtained in the growth phase of the cell culture (the relevant phase), therefore the results obtained are considered to be promising, proving that the fitting routine is valid, and that the cell concentration can be measured in real time using an oscillator.

Abstract: As the policies and regulations currently in place concentrate on environmental protection and greenhouse gas reduction, we are steadily witnessing a shift in the transportation industry towards electromobility. There are, though, several issues that need to be addressed to encourage the adoption of EVs at a larger scale. To this end, we propose a solution capable of addressing multiple EV charging scheduling issues, such as congestion management, scheduling a charging station in advance, and allowing EV drivers to plan optimized long trips using their EVs. The smart charging scheduling system we propose considers a variety of factors such as battery charge level, trip distance, nearby charging stations, other appointments, and average speed. Given the scarcity of data sets required to train the Reinforcement Learning algorithms, the novelty of the recommended solution lies in the scenario simulator, which generates the labelled datasets needed to train the algorithm. Based on the generated scenarios, we created and trained a neural network that uses a history of previous situations to identify the optimal charging station and time interval for recharging. The results are promising and for future work we are planning to train the DQN model using real-world data.

Improving the operational reliability of nuclear power plants, combined heat and power plants (CHP), as well as oil and gas pipelines is a priority task in the development of a variable-speed drive for lock valves used at these facilities. The paper analyzes technical requirements for such devices; the motor has been selected, its electrical equilibrium and moment equations have been obtained; recommendations for the selection of the kinematic drive scheme have been formulated. Based on the theoretical data obtained, a prototype has been developed, manufactured and tested.

An analysis is presented of the possible existence of a second anomalous dipole moment of Dirac’s particle next to the angular one. It includes a discussion why, in spite of his own derivation, Dirac has doubted about its relevancy. It is shown why since then it has been overlooked and why it has vanished from leading textbooks. A critical survey is given on the reasons of its reject, including the failure of attempts to measure and the perceived violations of time reversal symmetry and chargeparity symmetry. It is emphasized that the anomalous electric dipole moment of the pointlike electron (AEDM) is fundamentally different from the quantum field type electric dipole moment of an electron (eEDM) as defined in the standard model of particle physics and that its measurement requires different instrumentation. A proposal has been described how to prove or disprove its existence by experiment. Moreover, by reference from literature, the possible impact is discussed in the nuclear domain and in the gravitational domain.

Recently, design of electric scooters (ESs) has commonly adopted brushless DC motors (BLDCMs) in place of brushed DC motors. This invention develops a new anti-lock braking system (ABS), based on a slip-ratio estimator, for ES utilizing the braking force generated by the BLDCM when electrical energy releases to the load yielding an analogous effect of ABS control in gas-engine vehicles. Comparing to mechanical ABS, the design possesses the advantages of rapid torque responses due to fast actuating response. The electrical ABS is realized by associating with kinematic and Short-circuit braking. A current controller is used to adjust the braking force, while the sliding mode control strategy is adopted to regulate the slip ratio for best road adhesion while braking. Real-world experiments have been conducted for functional and performance verification.

This article proposes a particular strategy to proceed with a progressive electrification of public transport systems in cities. Starting from a bus operation model, the possible electrification of two routes is analysed, one urban and another extra-urban in the city of Pisa. An estimate is made of the energy uses associated with certain operating modes. The maximum level of consumption is estimated at approximately 280 kWh per day per bus for the urban route and excluding some special days, less than 215 kWh per day for the extra-urban route, for which a hybrid bus is proposed. Starting from an estimate of the daily consumption for the management of the two routes, the sizing of a photovoltaic system distributed on some modular shelters which serves to power the same routes is carried out. The resulting system has a power of the order of 190-200 kW. The modular solution is also outlined, and an installation is proposed. The analyzed case lends itself to being easily replicated.

A self-propelled electric tea seed-planter is designed to address the lack of tea seed seeding equipment, low seeding efficiency, and poor seeding uniformity. Based on the physical characteristics of the tea seeds and the agronomic requirements of tea planting, the key structure of the planter is designed, and the structural parameters are determined. The motor and battery configurations are determined by calculating the power consumption of the entire machine. In a field experiment, the driving gear (A), ditching depth (B), and planting gear position (C) are used as test factors, and the acceptance index (AI), replay index (RI) and leakage index (LI) are used as test indexes. The test results showed that the driving speed and planting gear position significantly affect the acceptance index, replay, and leakage index, whereas the ditching depth has little effect on the performance indexes. When the driving speed was medium, ditching depth was 30 mm, and planting gear position was in the third gear, the corresponding acceptance index was 87.22%, the replay index was 8.89%, and the leakage index was 3.89%. The test prototype has a good working quality and can provide theoretical guidance for production practices.