In terahertz communication systems, lens antennas used in transceivers are basically plano-convex dielectric lenses. As the aperture increases and the focal length decreases, the thickness and mass of the plano-convex lens increase rapidly. Through theory and simulation, we designed a Fresnel lens suitable for the terahertz band to meet the requirements of large aperture and short focal length, and simulated the performance, advantages and disadvantages of the terahertz Fresnel lens. A 300GHz terahertz wireless communication system was built to verify the gain effect of the Fresnel lens antenna. The experimental results show that the Fresnel lens can amplify the signal in the terahertz band. The theoretical gain of a 30 cm Fresnel lens is 48.83dB, while the actual measured gain is approximately 45dB.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

Search for the new non-invasive methods of investigating the functioning of human internal organs is an urgent task. One of these methods for assessing the functioning of the human res-piratory system is electromagnetic sensing, based on a significant difference in the dielectric permittivity of muscle tissue and air. During breathing, when the lungs are filled with air, the dielectric permittivity of the lungs decreases, which leads to a change in the level of the elec-tromagnetic signal passing through the body. Results of experiments on recording changes in the level of electromagnetic radiation passing through the human body, performed on an experimental device consisting of eight transmitting and receiving antennas located on opposite sides of the chest have been presented in the article. The possibility of visualizing the measured “pulmonograms” in the form of dynamic two-dimensional images showing the process of filling various parts of the lungs with air has been demonstrated.

The storm of November 12th-13th, 2019 provoked the displacements of boulders in a central Mediterranean rocky coast; with reference to a selected area, prone to the boulder production and geomorphologically monitored for years, a field-oriented study approach was applied for the phenomenon, by collating data concerning pre-storm locations and kinematics of these boulders. The number of displaced boulders is 11, that is, in terms of morphological imprint of a specific storm, one of the major study cases for the Mediterranean. In addition, based on widely used hydrodynamic equations, the minimum wave height required to displace the boulders is assessed. The values conform with the expected values for the wave climate dominating during the causative meteorological event and give a measure of the energy of the storm slamming the coast. Boulder dislodgements usually have plays a key role in determining the rate of the coastal recession, likely also in the investigated area. In view of an adverse climate evolution with a possible increase of energy and frequency of severe storms, the results deriving from the study of this morphodynamics should be considered for the hazard assessment and coastal management.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

This paper presents design and optimization of a small-size electromagnetic induction heating control system powered by a 3.7V-900mAh lithium battery and featuring an LC series resonant full bridge inverter circuit, which can be used in small size materials heating applications, such as micro medical devices. The effects of resonant capacitance, inductor wire diameter, heating tube material and wall thickness are studied to maximize the heating rate of the workpiece and meantime reduce the temperature rise of the NMOS transistor. The optimal circuit configuration meeting the design requirements was finally identified via comparing the operational parameters and NMOS transistor loss under different circuit conditions. The validation experiments were conducted on a designed electromagnetic induction smoking devices. The results indicate that under an output current of 4.6A, the heating tube can reach up to the temperature target of 250℃ within 11 seconds, and all NMOS transistors stay below 50°C in a 5 minutes heating process.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Abstract: Palynomorph assemblages and mineral microfossils from five southern Red Sea coastal environments were studied to demonstrate their distribution pattern and suggest their source. The environments studied were 1. mangrove swamp 2. middle Holocene paleochannel 3. algal mat, 4. Sabia Island coral reef, and intertidal zone. The samples studied were from the top 3 cm semi-consolidated sediments from various environments. Standard palynological maceration technique was used to isolate palynomorphs. These sediment samples are mainly clay and fine sand and yielded low numbers but high diversity of palynomorph assemblages. They are grouped into pollen and spores, dinoflagellate cysts, and algal remains, fungal spores, hyphae and fruit bodies, protists, and invertebrates. A few Ascidian and sponge spicules, and phytoliths (mineral microfossils) occur in the Sabia Island coral reef environment. The protists and invertebrate remain include microforaminifera, thecamoebians, tintinnomorphs, crustacean and annelid palynomorphs. The assemblage also includes six form taxa belonging to the form genera Katora and Mangrovia. These palynomorphs belong to both marine and terrestrial environments and are of autochthonous and allochthonous origins. The source and genetic relationship of each palynomorphs is discussed.

Background: Tibial shaft fractures are the most common of long bone fractures. The gold standard for management is locked intramedullary nailing. The freehand method under fluoroscopic monitoring is the most often utilized method for distal screw locking. Electromagnetic guidance-based distal screw locking methods have gained popularity recently. The study's objective is to evaluate the system using electromagnetic tracking data against the free-hand technique. Methods: Sixty-three patients who received intramedullary nailing for tibial shaft fractures at our institute between January 2018 and May 2022, were included in this study. Two groups of patients were distinguished: Group FH underwent freehand distal locking and intramedullary nailing, while Group SS underwent electromagnetically guided locking. Radiation exposure period, as well as dose area product, were noted and statistically compared. Results: In terms of dose area product, a mean value of 43.57±31.57 cGy/cm2 in group FH and a mean value of 27.62±11.20 cGy/cm2 in group SS (p < 0.05) was assessed. Concerning the duration of surgery a mean value of 128.83±26.51 minutes was reported in group FH and a mean value of 126.42±48.31 minutes in group SS (p > 0.05). Conclusions: This study confirms the use of electromagnetic-guided locking distal screws reduces the total time of exposure to ionizing radiation, with no difference in operating time.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

Earthquake forecasting is arguably one of the most challenging tasks in Earth sciences owing to the high complexity of the earthquake process. Over the past 40 years, there has been a plethora of work on finding credible, consistent and accurate earthquake precursors. This paper is a cumulative survey on earthquake precursor research, arranged into two broad categories: electromagnetic precursors and radon precursors. In the first category, methods related to measuring electromagnetic radiation in a wide frequency range, i.e. from a few hz to several MHz, are presented. Precursors based on optical and radar imaging acquired by space borne sensors are also considered, in the broad sense, as electromagnetic. In the second category, concentration measurements of radon gas found in soil and air, or even in ground water after being dissolved, form the basis of radon activity precursors. Well-established mathematical techniques for analysing data derived from electromagnetic radiation and radon concentration measurements are also described with an emphasis on fractal methods. Finally, physical models of earthquake generation and propagation aiming at interpreting the foundation of the aforementioned seismic precursors, are investigated

Extremely low-frequency electromagnetic fields (ELF-EMF) are ubiquitous in industrial-11 ized environments due to the continuous use of electrical devices. Our previous studies demon-12 strated ELF-EMF affects muscle cells by modulating oxidative stress and enhancing myo-genesis. 13 This pilot study investigated these effects on skeletal muscles of sedentary adult mice, assessing 14 physiological responses to ELF-EMF exposure and potential modulation by antioxidant supplemen-15 tation. Male C57BL/6 mice were exposed to ELF-EMF (0.1 or 1.0 mT) 1 hour/day up to 5 weeks, and 16 fed a standard diet without or with N-acetyl-cysteine (NAC). Results showed transient increases in 17 muscle strength (after 2-weeks’ exposure at 1.0 mT), potentially linked to muscle fiber recruitment 18 and activation, revealed by higher PAX7 and MyH expression levels. After ELF-EMF exposure, ox-19 idative status assessment revealed transient increases in expression levels of SOD1 and catalase en-20 zymes, in total antioxidant capacity and in protein carbonyl levels, marker of oxidative damage. 21 These effects were partially reduced by NAC. In conclusion, ELF-EMF exposure affects skeletal 22 muscle physiology and NAC supplementation partially mitigates these effects, highlighting the 23 complex interactions between ELF-EMF and antioxidant pathways in vivo. Further investigations 24 on ELF-EMF as a therapeutic modality for muscle health are necessary.

Deep underground laboratories offer advantages for conducting high-precision observations of weak geophysical signals, benefitting from a low background noise level. It is both valuable and feasible to enhance strong, noisy ground electromagnetic (EM) field data using synchronously recorded underground EM signals, which typically exhibit a high signal-to-noise ratio. In this study, we propose an EM field reconstruction method employing a Long Short-Term Memory (LSTM) recurrent neural network with referenced deep underground EM observations. Initially, a deep learning model was developed to capture the time-varying features of underground multi-component EM fields using the LSTM recurrent neural network. Subsequently, this model was applied to process synchronously observed strong, noisy data from other conventional observation systems, such as those at surface, to achieve noise suppression through signal reconstructions. Both theoretical analysis and practical observational data suggest that the proposed method effectively suppresses noise and reconstructs clean EM signals. This method is efficient and time-saving, representing an effective approach to fully utilizing the advantages of deep underground observation data. Furthermore, this method could be extended to the processing and analysis of other geophysical data.

For the first time, the effect of a significant change in the resistance of the aquatic environment of a population of protozoan microorganisms under the influence of radiofrequency electromagnetic radiation from cell phones has been experimentally studied. The results of the experiment demonstrate the biological nature of the changes occurring in the “water population of protozoa” system, which indicates that the impact of radiation directly affects the cell. This conclusion is confirmed by the same order of magnitude time of information exchange between individual individuals of the population in the calculation and in the experiment. An extremely low concentration of protozoa in the experiment was established, equal to 1000 pcs./liter, at which the indicated effect is observed.An unambiguous dependence of the biological effect in the “water – amoeba population” system on the average power of electromagnetic radiation of cell phones, both in standby mode and in talk mode, has been established. It is concluded that the presented method of changing the physical properties of the aquatic environment of a population of protozoa under the influence of electromagnetic fields can be a model experiment in identifying the mechanisms of interaction of biological systems with electromagnetic radiation, determining the response time of biological systems to external electromagnetic influence, and establishing the degree of influence of radiation in the 4G, 5G ranges.

Background/Objectives: PEMF therapy has gained significant attention due to its potential benefits in promoting tissue repair and improving overall well-being. Recent publications in the field of exercise physiology, showed that pulsed electromagnetic fields (PEMFs) enhanced the velocity and the quantity of muscle O2 available and the rate of muscle oxygen extraction and utilization, in semi-professional cyclists, during a heavy constant-load exercise. In this paper, we investigate the effect of stimulation on muscular activation, in sedentary young people, during a constant-load exercise, performed at moderate intensity. Methods: Nine male sedentary young people, partic-ipated in this study. The response of the muscle activity, was recorded by surface EMG and assessed measuring the root mean square (RMS) normalized to the peak of the maximum voluntary con-traction. Data were collected in the right vastus Medialis (RVM) and right Biceps Femoris (RBF) at the baseline (standstill sitting), on warm-up (unloaded cycling) and during 30 minutes of con-stant-load exercise, in two experimental conditions (PEMF ON vs PEMF OFF). Results: The mul-tivariate analysis of variance performed on RVM showed a significant effect of PEMF in both warmup and exercise, while on RBF showed a significant effect of PEMF and warmup. Conclusions: PEMF strongly enhanced the amplitude of muscle activity in young sedentary people. The increase in the amplitude of the muscular response may lead to a higher oxygen consumption and release.

Low-frequency electromagnetic induction (EMI) is a non-invasive geophysical method that is based on the induction of electromagnetic (EM) waves into the subsurface to quantify changes in electrical conductivity. In this study we present an open (design details and software are accessible) and modular system for the collection of EMI data. The instrument proposed allows to adjust the separations between the transmitter and up to four receiving antennas as well as the acquisition frequency (in the range between 3 and 50 kHz) to permit measurements with variable depth of investigation. The sensor provides access to raw data and the software described in this study allows control of the signal processing chain. The design specifications permit apparent conductivity measurements in the range of between 1 mS/m and 1000 mS/m, with a resolution of 1.0 mS/m and with a sampling rate of up to 10 samples per second. The sensor allows for a synchronous acquisition of a time stamp and a location stamp for each data sample. The sensor has a mass of less than 5 kg, is portable and suitable for 1-person operation, provides 4 hours of operation time on one battery charge, and provides sufficient rigidity for practical field operations.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

Conversion of electromagnetic energy into magnetohydrodynamic energy occurs when the electric conductivity changes from negligible to finite values. This process is relevant during the epoch of reheating of the early Universe at the end of inflation and before the emergence of the radiation-dominated era. We find that conversion into kinetic and thermal energies is primarily the result of electric energy dissipation and that the magnetic energy plays only a secondary role in this process. This means that, since electric energy dominates over magnetic energy during inflation and reheating, significant amounts of electric energy can be converted into magnetohydrodynamic energy when conductivity emerges early enough, before the relevant length scales become stable.

An eigenvalue equation representing symmetric (dual) quantum equation is introduced. The particle is described by two scalar wavefunctions, and two vector wavefunctions. The eigenfunction is found to satisfy the quantum Telegraph equation keeping the form of the particle fixed but decaying its amplitude. An analogy with Maxwellian equations is presented. Massive electromagnetic field will satisfy a quantum Telegraph equation instead of a pure wave equation. This equation resembles the motion of the electromagnetic field in a conducting medium. With a particular setting of the scalar and vector wavefunctions, the dual quantum equations are found to yield the quantized Maxwell's equations. The total energy of the particle is related to the phase velocity ($v_p$) of the wave representing it by $E=p\,|v_p|$, where $p$ is the matter wave momentum. A particular solution which describes the process under which the particle undergoes a creation and annihilation is derived. The force acting on the moving particle is expressed in a dual Lorentz-like form. If the particle moves like a fluid, a dissipative (drag) quantum force will arise.

The well-being and sociability of individuals have always been part of modernity. The development of new technologies that meet these aspirations is receiving increasing attention. Thus, strengthening the desired objectives of these tools and minimizing their undesirable side effects is the subject of a growing commitment. The present contribution aims, in this context, to evaluate and analyze the desired and undesirable effects of the interaction of electromagnetic fields with living tissues in general. This involves routines reinforcing expected functions as well as those controlling and protecting against undesirable effects. First, the interactions of electromagnetic fields with tissues are analyzed, involving their thermal biological effects of desired and undesired exposures. The roles of blood and sap fluids in bio-affected tissues are then analyzed. Secondly, the governing electromagnetic, bio-heat equations, and their coupled solution are studied. Third, the thermal behavior of tissues and the exposure adverse effects are examined. Next, monitoring and defending of the effects of exposures are discussed. This contribution illustrates and discusses mathematical modeling routines based on a generalized interaction of electromagnetic fields with living tissues.

In this study, we developed a lightweight shoe sensor system equipped with four high-capacity, compact triaxial force sensors and an inertial measurement unit. Remarkably, this system enabled measurements of localized three-directional ground reaction forces (GRFs) at each sensor position (heel, first and fifth metatarsal heads, and toe) and estimations of stride length and toe clearance during walking. Compared to conventional optical motion analysis systems, the developed sensor system provided relatively accurate results for stride length and minimum toe clearance. To test the performance of the system, 15 older and eight young adults were instructed to walk along a straight-line while wearing the system. The results revealed that compared to the young adults, older adults exhibited lower localized GRF contributions from the heel and greater localized GRF contribution from the toe and fifth metatarsal locations. Furthermore, the older adults exhibited greater variability in their stride length and smaller toe clearance with greater variability compared to the young adults. These results underscore the effectiveness of the proposed gait analysis system in distinguishing the gait characteristics of young and older adults, potentially replacing traditional motion capture systems and force plates in gait analysis.

The energy matrix worldwide has been going through difficulties in its discussions - such as irregular exploration, inefficient public policies, and arbitrariness concerning diplomatic and political definitions of those involved in this market. This work's general objective consists in analyzing associations and statistical inferences of the largest world oil producers, assimilating the contributions and singularities of this market from 1993 to 2020. Based on the Organization of the Petroleum Exporting Countries (OPEC), it was possible to identify the possible inferences and contributions of the ten largest oil producers in the world in more than two decades using statistical analysis through correlation, regression, and statistical analysis of variables. According to the research and the literature on the area, the oil market proposes support to its discussions, mainly in its productive approaches. It is possible to identify this market as a solid link to geopolitical actions, distributing the possibilities through economic bias and socio-cultural and historical factors on a global level.

In this paper, we investigate various graphene monolayer nanomesh structures (diodes) formed only by nanoholes, with a diameter of just 20 nm and etched from the graphene layer in different shapes (such as rhombus, bow-tie, rectangle, trapezoid, and triangle), and their electrical properties targeting electromagnetic energy harvesting applications. In this respect, the main parameters characterizing any nonlinear device for energy harvesting are extracted from tens of measurements performed on a single chip containing the fabricated diodes. The best nano-perforated graphene structure is the triangle nanomesh one, which exhibits remarkable performance in terms of its characteristic parameters, i.e., a 420 Ω differential resistance for optimal impedance matching to an antenna, a high responsivity greater than 1000 V/W, and a low noise equivalent power of 847 pW/√Hz at 0 V.

In this article, many experimental similarities between electromagnetic fields (which are applied in systems of electrons, atoms, and liquids) and strong interaction fields (which are applied in systems of quarks, nucleons, and nuclei) are reviewed. The currently accepted theories describing electromagnetic fields differ fundamentally from those describing strong fields. Therefore, the many similarities are quite surprising, and some are not adequately explained even today. Several such unexplained similarities are listed among the top open problems in particle physics, such as the “EMC effect,” the “proton spin crisis,” and the “strong CP problem.” This paper highlights, for the first time, the underlying common characteristics of these problems, potentially offering valuable contribution to future explanations.

We have shown that Newton’s third law does not strictly hold in a system with remote elements, due the finite speed of signal propagation and thus force imbalance occurs at the system’s center of mass. As the said system is affected by a total force for a finite duration, mechanical energy and momentums are gained by the system. In early works we assumed that the bodies were macroscopically charge neutral. Later we removed this restriction, thus analyzing the consequences on a possible electric charged relativistic motor. On the first published paper on this subject we studied this phenomena in general but gave only an example of a system reaching a stationary state, in this paper we shall analyze a charged retarded electromagnetic motor in a more general time dependent setting giving specific examples in which the system never reaches a stationary state yet produces steady linear momentum non the less.

We consider the propagation of electromagnetic waves in the Friedman – Lemaître – Robertson – Walker metric. The exact solutions for plane and spherical wave are written down. The corresponding redshift, amplitude change, and dispersion are discussed. We also speculate about the connection of the electromagnetic wave equation to the Klein–Gordon equation.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

Elevated salinity is one of the major environmental limitation factors of plant growth and development and salinity stress compromises the production and survival of plantation and urban forests and agricultural crops in the arid, semi-arid, and intertidal zones. Ulmus pumila, a salt- indigenous tree species in Asia and is widely deployed in salt-affected areas in China, and U.pumila is promising for multi-varietal forestry in plantation and urban forests. The comprehensive mechanism of the intraspecific salt tolerance is still not clear yet. Here, we investigated the physiological responses of the salinity stress based on the antioxidant enzyme activities, osmotic adjustments, and gas exchange among salt-tolerant U. pumila genotypes for 100 days under five different NaCl levels (0%, 0.3%, 0.5%, 0.7%, and 0.9% w/v) with natural surroundings and rain shade at age-2. Salt stress decreased height (HR), ground diameter (DR), and dry weight (biomass) were significantly different among genotypes. HR and performance indices were positively correlated with photosynthesis rate (Pn), apparent mesophyll conductance (AMC), and chlorophyll (CHLL) with (r= 0.7 - 0.8 ***), but were negatively related to the free proline, sugar, and protein accumulation (r=-0.5 ~ -0.7***). We found that high accumulation of sugars and more activities of SOD enzyme in leaf tissue contribute to the osmotic adjustment and ROS scavenging system under salinity treatment; the sugar content and SOD activity play key roles in U. pumila’s tolerance to salt stress, and are promising indicators for U. pumila species ex vitro selections. The ex vitro selection results align with the previous in vitro studies [37] and is promising for the MVF development.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

An analogy between magneto-fluid dynamics (MFD/MHD) and geostrophic flow in a rotating frame of reference including the existence of electromagnetic columns identical to Taylor-Proudman columns is identified and demonstrated theoretically. The latter occurs in the limit of large values of a dimensionless group representing the magnetic field number. Such conditions are shown to be easily satisfied in reality. Consequently, the electromagnetic fluid flow subject to these conditions is two dimensional and the streamlines are being shown to be identical to the pressure lines in complete analogy to rotating geostrophic flows. An experimental setup is suggested to confirm the theoretical results experimentally.

Diabetic patients need long-term and frequent glucose monitoring to assist in insulin intake. The current finger-prick devices are painful and costly which make noninvasive glucose sensors highly demanded. In this review paper, we discuss several advanced electromagnetic (EM) wave based technologies for noninvasive glucose measurement, including infrared (IR) spectroscopy, photoacoustic (PA) spectroscopy, Raman spectroscopy, fluorescence, optical coherent tomography (OCT) and microwave sensing. Development and progress of each method are discussed regarding fundamental principle, system setup and experimental results. Despite the promising achievements reported previously, there is no established product to obtain FDA approval or survive marketing test. Limitations and prospects of these techniques are discussed at the end of this review.

At present, the applications and efficacy of non-ionizing radiations (NIR) in oncotherapy are limited. In terms of potential combinations, the use of biocompatible magnetic nanoparticles as heat mediators has been extensively investigated. Nevertheless, the development of more efficient heat nanomediators that may exhibit high specific absorption rates still is an unsolved problem. Our aim was to investigate if externally applied magnetic fields and a heat-inducing NIR affect tumor cell viability. To this end, under in vitro conditions, different human cancer cells (A2058 melanoma, AsPC1 pancreas carcinoma, MDA-MB-231 breast carcinoma) were treated with the combination of electromagnetic fields (EMFs, using solenoids) and hyperthermia (HT, using a thermostated bath). The effect of NIR was also studied in combination with standard chemotherapy and targeted therapy. An experimental device combining EMFs and high intensity focused ultrasounds (HIFU)-induced HT was tested in vivo. EMFs (25 T, 4h) or HT (52C, 40 min) showed a limited effect on cancer cell viability in vitro. However, their combination decreased viability to approx. 16%, 50%, and 21% of controls values in A2058, AsPC1, and MDA-MB-231 cells, respectively. Increased lysosomal permeability, release of cathepsins into the cytosol and mitochondria-dependent activation of cell death are the underlying mechanisms. Cancer cells could be completely eliminated combining EMFs, HT and standard chemotherapy or EMFs, HT and anti-Hsp70-targeted therapy. As a proof of concept, in vivo experiments performed in AsPC1 xenografts showed that combination of EMFs, HIFU-induced HT, standard chemotherapy and a lysosomal permeabilizer induces a complete cancer regression.

Considerable efforts have been devoted to modifying gravity, which aim to elucidate the possible existence or nature of dark matter and energy, describe observational data more effectively, and formulate quantum gravity. In addition, despite the immense success of the quantum field theory, the framework requires renormalization techniques and breaks down at high energies. Recently, the Planck legacy 2018 release has confirmed the existence of an enhanced lensing amplitude in the cosmic microwave background power spectra, which prefers a positively curved early Universe with a confidence level higher than 99%. This study considers the implied curvature of the early Universe as the curvature of “the background or 4D conformal bulk as a manifestation of vacuum energy” and distinguishes it from the localized curvature that is induced in the bulk by the presence of celestial objects that are regarded as ”4D relativistic cloud-worlds.” Analogously, because gravity appears to emerge owing to spacetime curvature and does not exhibit critical characteristics shared by other fields, it has been incorporated as the local curvature of the bulk affecting the embedded quantum fields that are regarded as propagating “4D relativistic quantum clouds.” To consider the effects of the bulk on embedded clouds, this paper presents interaction field equations in terms of brane-world modified gravity and the perspective of geometrization of the quantum mechanics wherein gravity is manifested by the curvature of 4D conformal bulk as an indicator of the field strength of vacuum energy on the embedded 4D relativistic clouds in addition to the boundary interactions, which could remove the singularities and satisfy a conformal invariance theory. A visualization of the evolution of the 4D relativistic cloud-worlds over the conformal spacetime of the 4D bulk is presented, whereas the standard said theories can be recovered from the interaction field equations.

We derive the thermal noise spectrum of the Fourier transform of the electric field operator of a given wave vector starting from the quantum-statistical definitions and relate it to the complex frequency and wave vector dependent complex conductivity in a homogeneous, isotropic system of electromagnetic interacting electrons. We analyze separately the longitudinal and transverse case with their peculiarities. The Nyquist formula for vanishing frequency and wave vector, as well as its modification for non-vanishing frequencies and wave vectors follow immediately. Furthermore we discuss also the noise of the photon occupation numbers. It is important to stress that no additional assumptions at all were used in this straightforward proof.

Modern life implies a constant exposure of living organisms to electromagnetic fields generated by human made technology. The question of whether or not electromagnetic fields in the non-ionizing frequency range can affect cellular functions, increasing the risk of cancer or another pathologies is currently a subject of interest for scientific community of several disciplines of physics, biology, chemistry and medicine. The first part of this short review presents briefly the possible mechanism of interaction of electromagnetic fields in cellular level based in theoretical models and experimental results. The second part refers to experimental observations published by several authors about the potential cytotoxic and genotoxic effects of electromagnetic fields. Results of researches are no yet conclusive enough to accept or reject the genotoxic, carcinogenic or cytotoxic potential of these fields. Up to date the International Agency for Research on Cancer (IARC) has classified the X, gamma and ultraviolet radiation as carcinogenic and the fields generated by radio frequencies as possibly carcinogenic.

We employ another approach to quantize electromagnetic fields in the coordinate space, instead of the mode (or Fourier) space, such that local features of photons can be efficiently, physically, and more intuitively described. To do this, coordinate-ladder operators are defined from mode-ladder operators via the unitary transformation of systems involved in arbitrary inhomogeneous dielectric media. Then, one can expand electromagnetic field operators through the coordinate-ladder operators weighted by non-orthogonal and spatially-localized bases, which are propagators of initial quantum electromagnetic (complex-valued) field operators. Here, we call them QEM-CV-propagators. However, there are no general closed form solutions available for them. This inspires us to develop a quantum finite-difference time-domain (Q-FDTD) scheme to numerically time evolve QEM-CV-propagators. In order to check the validity of the proposed Q-FDTD scheme, we perform computer simulations to observe the Hong-Ou-Mandel effect resulting from the destructive interference of two photons in a 50/50 quantum beam splitter.

Electric and/or magnetic fields are generated by stationary charges, uniformly moving charges and accelerating charges. These field components are described in the literature as static fields, velocity fields (or generalized Coulomb field) and radiation fields (or acceleration fields), respectively. In the literature, the electromagnetic fields generated by lightning return strokes are presented using the field components associated with short dipoles and in this description the one to one association of the electromagnetic field terms with the physical process that gives rise to them is lost. In this paper, we will derive expressions for the electromagnetic fields using field equations associated with accelerating (and moving) charges and separate the resulting fields into static, velocity and radiation fields. The results illustrates how the radiation fields emanating from the lightning channel give rise to field terms varying as inverse of distance and distance squired, the velocity fields generating field terms varying as inverse of distance squired and the static fields generating fields components varying as inverse of distance squired and distance cube. These field components depend explicitly on the speed of propagation of the current pulse. However, the total field does not depend explicitly on the speed of propagation of the current pulse. It is shown that these field components can be combined to generate the field components pertinent to the dipole technique. However, in this conversion process the connection of the field components to the physical process taking place at the source that generate these fields (i.e. static charges, uniformly moving charges and accelerating charges) is lost.

We propose a novel framework for understanding quantum phenomena through the lens of a modified electromagnetic spacetime governed by Einstein field equations. By assuming the existence of an electromagnetic spacetime that adheres to these modified geodesic and Einstein field equations, provided the field equations satisfy the Coulomb force law in weak-field approximations, we explore the derivation of Maxwell’s equations and highlight the necessity of incorporating spin to validate these equations. We derive the wave equation for the normalized transverse metric and establish its equivalence with the de Broglie wave proposition, suggesting a relationship between this metric and the particle's wavefunction. This approach offers a classical explanation for several quantum phenomena, including the double-slit experiment, entanglement, tunneling, non-locality, and wavefunction collapse. Additionally, it posits a method to visualize atomic orbital structures in line with quantum mechanical predictions. These findings suggest that the foundational principles of quantum mechanics can be interpreted as linearized approximations of general relativity applied to electromagnetic spacetime. While this theory does not yet extend to the correlations between general relativity, quantum electrodynamics (QED), and quantum chromodynamics (QCD), it provides a valuable visualization tool for physicists and advances our understanding of the unresolved challenges linking quantum mechanics with general relativity.

The development of devices for In-Situ Resource Utilization (ISRU) of the lunar surface powder (regolith) by means of microwaves needs regolith simulants with electromagnetic properties similar to the lunar regolith. This document deals with the measurement of complex permittivity and dielectric loss tangent of the aforementioned simulants at ambient temperature from 400 MHz to 20 GHz. In addition, further studies are carried out taking into account humidity of the samples and their densities. The obtained results will be applicable for comparing the measured values of EAC-1A and JSC-2A among them and with other previously measured simulants and real samples. The measurements are carried out applying two different nonresonant techniques: Open- Ended Coaxial Probe (OECP) and Transmission Line. For this purpose, the DAK and EpsiMu commercial kits were respectively used.

A deep relationship is identified between the Coulomb Force and Gravity. A gravitational constant for strong gravity is calculated from the relationship. The equivalence between mass and charge is explored. Implications are given for the expansion of Einstein's Field Equations to include vector gravity.

During the explosion of energetic materials, obvious electromagnetic interference will be generated, which will affect the normal operation of surrounding electronic equipment. Experiments are still an important means to study this issue. A set of electromagnetic radiation measurement device based on short-wave omnidirectional antenna and ultra-wideband omnidirectional antenna is designed to measure the electromagnetic radiation generated by the explosion of energetic materials of different masses, and the electromagnetic radiation characteristics are obtained through data processing. The results show that the mass of the energetic material has a significant effect on the time-domain characteristics of the electromagnetic radiation generated by the explosion: the higher the mass of the energetic material, the shorter the delay response of the electromagnetic signal, the longer the duration, and the earlier the peak appears. The frequency of electromagnetic radiation signals generated by the explosion of energetic materials is mainly concentrated below 100 MHz, and the energy is most concentrated in the frequency band of 0~50 MHz. The composition of energetic materials has the greatest influence on the spectral distribution, and the spectral distribution of electromagnetic radiation produced by the explosion of explosives with different compositions has obvious specificity. The electromagnetic radiation intensity generated by the explosion of energetic materials has a strong correlation with the distance from the explosion center, and it decreases with the increase of the distance, and the decreasing range is large. The structure and detonation method of energetic materials can change the geometrical motion mode during the explosion, resulting in the non-uniformity of electromagnetic radiation propagation.

The detection of Dark Matter is the greatest outstanding problem in modern cosmology. Several attempts have been taken for this without any remarkable success. To find out a suitable way of detection we need to understand its nature comprehensively. In the present article, a hypothesis is described considering Dark Matter as a normal matter. Its peculiar behavior is explained considering its existence in BEC state in the coolest part of the universe that makes it an electromagnetic insulator. Depending upon this hypothesis an experimental verification method is proposed.

This paper first explains the theory of the origin of force from a new perspective, explaining that the origin of all forces is caused by the "missing of energy in the time dimension" (non-conservation in a certain period of time), and constructs a unified theory of force on this basis. Then, through the unified theory of force, the following phenomena are reinterpreted: (1) The common origin of the inverse square law of gravitation and electromagnetic force; (2) The origin of the repulsive force of electrons and protons at small distances; (3) The mystery of the rotation curve of galaxies and the new explanation of "dark matter"; (4) explain the origin of the magnetic field; (5) Predict that moving magnets have the same radiation effect as charged particles (electron magnetic moments also have radiation effects); (6) Reinterpret Maxwell's displacement current; (7) Reinterpret synchrotron radiation and bremsstrahlung; (8) Explain that the strong and weak forces are short-range forces; (9) Predict the true structure of black holes and the origin of gravitational waves;(10) Possible explanation for the origin of the speed of light.

The currently available anti-cancer therapies, such as gamma-radiation and chemotherapeutic agents, induce cell death and cellular senescence not only in cancer cells but also in the adjacent normal tissue. New anti-tumor approaches focus on limiting the side effects on normal cells. In this frame, the potential anti-tumor properties of Pulsed Electromagnetic Fields (PEMFs) through irradiation of breast cancer epithelial cells (MCF-7 and MDA-MB-231) and normal fibroblasts (FF95) were investigated. PEMFs had a frequency of 8 Hz, full-square wave type, magnetic flux density of 0.011 T and applied twice daily for 5 days. Data collected showcases that PEMF application decreases the proliferation rate and viability of breast cancer cells while having the opposite effect on normal fibroblasts. Moreover, PEMF irradiation induced cell death and cellular senescence only in breast cancer cells without any effect in the non-cancerous cells. These findings suggest PEMF irradiation as a novel, non-invasive anti-cancer strategy in combination with senolytic drugs, to eliminate both cancer and the remaining senescent cells while simultaneously avoiding the side effects of the current treatments.

Highly efficient, broadband and distinctively structured electromagnetic wave (EMW) absorption materials exhibit huge exceptions with multi-functions in both military and civilian fields. Searching the relationship between structural and EMW performance is beneficial to develop outstanding microwave absorption materials, and has become an attractive research topic. In this study, we briefly reviewed the different EMW absorption mechanisms and key influence factors, then, present the latest developments in low-dimensional (LD) EMW absorption materials. We provide a comprehensive discussion of remarkable examples and summarize the main information related to the structure-function relationship of dimensional design and structural engineering in order to facilitate the rapid evolution of this fascinating field.

The combination of interstitial hyperthermia treatment (IHT) with high dose rate brachytherapy (HDR-BT) for prostate cancer treatment and has the potential to improve clinical outcome, since it highly enhances the efficiency of cell kill, especially when applied simultaneously. Therefore, we have developed the ThermoBrachy applicators. To effectively apply optimal targeted IHT, treatment planning is considered essential. However, treatment planning in IHT is rarely applied since it is regarded difficult to accurately calculate the deposited energy in the tissue in a short enough time for clinical practice. In this study, we investigated various time-efficient methods for fast computation of the electromagnetic (EM) energy deposition resulting from the ThermoBrachy applicators. Initially, we investigated the use of an electro-quasistatic solver. Next, we extended our investigation to the application of geometric simplifications. Furthermore, we investigated the validity of the superpositioning principle, which can enable adaptive treatment plan optimization without the need for continuous recomputation of the EM field. Finally, we evaluated the accuracy of the methods by comparing them to the golden standard Finite-Difference Time-Domain calculation method using gamma-index analysis. The simplifications considerably reduced the computation time needed, improving from >12 h to a few seconds. All investigated methods showed excellent agreement with the golden standard by showing a >99% passing rate with 1%/0.5 mm Dose Difference and Distance-to-Agreement criteria. These results allow the proposed electromagnetic simulation method to be used for fast and accurate adaptive treatment planning.

We investigate regular damped oscillatory structures appearing in the "effective" form factor of various hadrons. The behavior of this form factor can be extracted from the experimental information on total cross sections, the processes $\sigma_{tot}(e^+e^- \to h \bar h)$, $h=\pi^{\pm}, K^{\pm}, K^0, p, n $ are examined. The apparent oscillations have been observed for the first time for the proton and we show, taking also other hadrons into the consideration, that they are an arbitrary artifact resulting from a very simplistic theoretical description based on an elementary three-parametric model. If the data are described by a more appropriate and well physically funded U\&A model, then the oscillations disappear. In addition, if the simple model is used to describe the data, one observes that the oscillations are opposite for particles which form an isospin dublet. We show, by using the U\&A model, that this feature is explained by the transformation properties of the corresponding states in the isotopic space.

To address the challenges associated with the difficult electromagnetic (EM) scattering computations of anisotropic dielectric-coated metallic composite targets, we proposed an efficient hybrid algorithm for simulating the EM scattering of complex targets with anisotropic dielectric coatings. This method, based on Impedance Boundary Condition (IBC), utilizes surface impedance vectors to describe the EM properties of the dielectric. It fully leverages the respective advantages of the low-frequency Method of Moments (MoM) and the high-frequency Physical Optics (PO) to achieve high-precision and rapid EM simulation of anisotropic dielectric-coated metallic composite targets. Employing boundary conditions and equivalent principles, we equivalently transform the EM scattering problem of targets with thin dielectric coatings into the radiation problem of equivalent EM current on impedance surfaces. This enables the high-precision and rapid calculation of Radar Cross Sections (RCS) for complex targets with anisotropic dielectric coatings. Using examples such as a square plate structure, a simplified aircraft, and a complex satellite model, the simulation results exhibit a high degree of agreement with full-wave numerical solutions and demonstrate a significant advantage in computational resources. This research convincingly demonstrates the accuracy and effectiveness of the proposed method.

Electromagnetic (EM) waves, used for purposes such as geophysical characterization, impact properties to be measured. This paper describes the effects of radio frequency (RF) waves on the hydraulic conductivity of glass beads and natural sand. A series of tests were conducted using a customized, rigid-wall, cylindrical permeameter inside a resonant cavity made of Plexiglas covered with electrically conductive transparent films. Constant head ASTM-D2434 [1] tests were performed to measure the samples’ hydraulic conductivity. RF stimulation was performed using a magnetically coupled loop antenna at a constant frequency of 726 MHz and input power levels of 10, 25, 40, and 50 Watts. The hydraulic conductivity of both natural sand and glass-bead samples increased with RF stimulation. Furthermore, measurement of the electric-field component of RF waves was also performed to illustrate the pattern of the electric field as well as evaluate the RF impact on the hydraulic conductivity tests. The electric field was numerically simulated and validated against experimentally measured electric fields. A finite-difference numerical model was developed in MATLAB to analyze the seepage flow, which was then validated against the experimental results. An optimization scheme was then used to develop a governing equation for the RF impact on hydraulic conductivity.

As semi-airborne mineral exploration has limited budgets, it is critical to design experimental procedures that generate data maximizing the desired information We investigate the effects of transmitter-receiver geometries for a variety of anomalies and semi-airborne layouts. Our simulations indicate that 200 m flight line spacing and 100 m point distance are the optimal trade-off between coverage and survey progress for various targets. Based on the target size and distance between the transmitter and the target, the transmitter length should be at least equal to the length of the target and for more than 1 km, at least two or three times the target size. Likewise important are the location and direction of the transmitter cables, which can have great impact on the result of inversion and should be parallel to the target strike. By using more than one transmitter, better results are obtained. If the strike of the target is known, transmitters should be parallel to each other and if not, it is better to use perpendicular transmitters. Results showed that the optimal distance between transmitters is 3 km. Our simulations show that it is even possible to recover targets just below the transmitter in corresponding areas of masked data.

During the launch and return of a spacecraft, the intense combustion of propellants generates strong electromagnetic radiation, which interferes with the operation of electronic equipment in the spacecraft. To improve the electromagnetic compatibility of electronic equipment in spacecraft, it is necessary to study the electromagnetic radiation characteristics of rocket fuel. An electromagnetic radiation measurement system based on antennas is designed to measure the electromagnetic radiation generated by rocket fuel, and the electromagnetic radiation characteristics are obtained through data analysis. The mechanism of the electromagnetic radiation generated by rocket fuel is comprehensively analysed through the spatial, time-domain, frequency-domain, and energy-domain characteristics. A characterization model is established to provide a reliable scheme for evaluating the influence of rocket fuel electromagnetic radiation on electronic equipment in spacecraft.

The present paper reports an exact approach quantifying the electromagnetic contribution to the anomalous magnetic moment occurring in isolated system comprised of non-composite particle carrying elementary electric charge. Essential averaging procedure and regularization of the electromagnetic field potentials necessary when quantifying the electromagnetic self-interactions and when deriving equations of motion without singularities and obeying the conservation laws are thoroughly discussed. The study shows that the dynamics of the considered system is associated to unique classical transcendental equations of motion satisfied by the particle's velocity and the electromagnetic contribution to the anomalous $g$-factor known from the quantum electrodynamics. The equations of motion lead to an exact analytical expression for the anomalous $g$-factor that provides more accurate result than that calculated with the aid of quantum electrodynamics. It matches the experimentally measured value reported in the literature to a one part per trillion. We obtain a_e=0.00115965218000(65) thus reveling the potential of non-perturbative, non-probability methods in predicting the electron's anomalous g-factor.

The propagation of electromagnetic waves beyond the line of sight can be caused by atmospheric ducts, which are a significant concerns in the fields of radar and communication. This paper utilizes data from seven automatic stations and five radio-sounding stations to statistically analyze the characteristics of the atmospheric ducts in the northwest region of the South China Sea (SCS). After verifying the practicality of numerical analysis data from NCEP CFSv2 and ERA5 in studying atmospheric ducts using measured data, we analyzed the space-time distribution characteristics of the height of the regional evaporation duct and the bottom height of the elevated duct. Using the parabolic equation model, we simulated electromagnetic propagation loss under different frequencies and radiation elevation angles in both uniform and non-uniform duct environments within a typical atmospheric duct structure. The study found that the NCEP CFSv2 data accurately captures the evaporation duct height and duct occurrence rate in the study area, and the elevated duct bottom height obtained from the inversion of ERA5 and the measured data has a good consistency. The occurrence rate and height of evaporation duct in coastal stations in the northwest of the SCS vary significantly by month, demonstrating clear monthly distribution patterns. Conversely, changes in the Xisha station are minimal, indicating good temporal uniformity. For lower atmospheric ducts, the difference in occurrence rates between 00:00 and 12:00 (UTC) is negligible. The occurrence probability of elevated ducts in the Beibu Gulf area is relatively high, mainly concentrated from January to April, and the Xisha area is dominated by surface ducts without foundation layer, mainly concentrated from June to August. The monsoon plays a critical role in the generation and evolution of atmospheric ducts in the northwest of the SCS, with the height of the evaporation duct increasing and the bottom height of the elevated duct decreasing after the onset of the summer monsoon. Electromagnetic propagation simulations demonstrate that higher frequency and lower elevation angles of radiation sources in the trapping layer of the evaporation duct make it easier to be trapped. As the evaporation duct height decreases, the amplitude of the "sinusoidal fluctuation" of the propagation loss also decreases. Frequency changes of the radiation source in the surface duct environment have minimal impact on electromagnetic propagation loss, but the elevation angle of the radiation source is a critical factor. The frequency of the "sinusoidal fluctuation" in propagation loss is higher in a hybrid duct environment compared to a uniform surface duct. Additionally, the propagation loss increases faster with distance at the height of the evaporation duct, resulting in greater electromagnetic propagation loss.

We examine here characteristics of electromagnetic waves that propagate through an unbounded space filled with a homogeneous isotropic chiral medium. Resulting characters are compared to those of the electromagnetic waves propagating through an achiral free space. To this goal, we form energy conservation laws for key bilinear parameters in a chiral case. Due to a nonzero medium chirality, conservation laws turn out to contain extra terms that are linked to the spin-orbit coupling, which is absent for an achiral case. As an example, we take a plane wave for achiral case to evaluate those bilinear parameters. Resultantly, the conservation laws for a chiral case are found to reveal inconsistencies among several bilinear parameters that constitute the con-servation laws , thereby prompting us to establish partial remedies for formulating proper wave-propagation problems.

This article is a big picture of how electrical noise or conducted Electromagnetic Interference (EMI) is generated and mitigated in power converters. It gives an overview of what EMI in power converters is – from generation through to conduction and mitigation. It is meant to cover the complete subject as a summary so that the reader will have an outline of how to control conducted EMI by design (where possible) and how to mitigate by filtering. A clear distinction is made between Differential Mode (DM) and Common Mode (CM) EMI generation and mitigation. By using a boost converter as an example the trade-offs for DM noise control are discussed. It is shown how CM EMI is generated in a boost converter using the concept of the “Imbalance Difference Model” (IDM). Practical measurements for an in-line power filter is given showing the effect of the filter on the total EMI of a boost converter. Measurements for the CM current produced due to the imbalance difference for different values of the boost conductor are also shown. The main contribution of this study is linking CM noise generation to DM EMI. It is shown that CM noise is a direct consequence of DM noise (although circuit imbalance and coupling to a common ground also play a role). This paper will be useful to designers seeking the “bigger picture” of how EMI is generated in power converters and what can be done to mitigate the noise.

Negative corona discharges occur widely in high voltage transmission lines and charged aircraft, which can cause strong electromagnetic interference. Negative corona discharge is typically performed simultaneously at multiple discharge points. In this study, the current and its EM radiation characteristics of single-needle and multi-needle negative corona discharge in different conditions were tested. The current and electromagnetic radiation characteristics of the two discharge structures were compared. The dipole radiation model was established to analyze the EM radiation characteristics of the negative corona discharge.The results show that, It is only when the voltage reaches a certain threshold that the current and electromagnetic radiation fields of the multi-needle discharge structure will be superimposed and their amplitudes will increase significantly. The frequency of electromagnetic radiation signal does not change with the number of needles, cathode geometry and applied voltage, but only depends on ambient pressure. It provides a basis for detecting corona discharge sources under different conditions.

In the provinces of the region, empirical constructions reached maximum points with these practices. The effects and pathologies appear as physical, chemical and mechanical failures in pillars, walls and roofs, generating uncertainty for the user. The current powerful design can detect the interior deterioration of coatings in adobe, brick and concrete constructions, and prevent collapses, material and economic losses. Experimental methods performed affirm the serious validity. The accuracy of the simulation and design provide a pre-test reliability of 95%. Five piles constructed of various materials participate in the prototype performance test, there is a correlation (R=0.9997) between the magnetic field range "B" (cm) and density "ρ" (g/cm³), also by increasing the current (i) in transit Q1 and coil L1, the induction of the "B" increases proportionally until penetrating the density of the wall of the building, having 5% reading error.

With the ongoing fifth-generation cellular network (5G) deployment, electromagnetic field exposure has become a critical concern. However, measurements are scarce, and accurate electromagnetic field reconstruction in a geographic region remains challenging. This work proposes a conditional Generative Adversarial Network to address this issue. The main objective is to reconstruct the electromagnetic field exposure map accurately according to the environment’s topology from a few sensors located in an outdoor urban environment. The model is trained to learn and estimate the propagation characteristics of the electromagnetic field according to the topology of a given environment. In addition, the conditional Generative Adversarial Network based electromagnetic field mapping is compared with simple kriging. Results show that the proposed method produces accurate estimates and is a promising solution for exposure map reconstruction.

The well-known coupling between the magnetic and electric fields in electromagnetic radiation is revisited in light of the recent introduction of a microscopic theory for the Ørsted magnetic field induction. I argue that, if the Ørsted magnetic field induction does indeed have a microscopic origin rather than the continuum solution offered by the Maxwell-Ampere equation, the "electromagnetic wave"' propagating in vacuum will not have a magnetic component.

In the process of deflagration of energetic materials, strong electromagnetic radiation is to be generated, which causes the surrounding electronic equipment to fail to work normally. To solve this problem, it is necessary to clarify the mechanism of electromagnetic radiation generated by energetic materials. The mechanism of plasma changed by the deflagration of energetic materials is an important topic in the aerospace and geophysics fields. The academic community holds two main viewpoints on the mechanism of electromagnetic radiation generated by energetic materials: one is that the solid material is squeezed and deformed during the deflagration of energetic materials, and the charges of different polarities rub in space to form effective electric dipoles, which eventually generate electromagnetic radiation. Another view is that the deflagration of energetic materials causes the temperature of the medium to rise sharply, and bremsstrahlung is formed during the compression and diffusion of the high-temperature wave front, resulting in the generation of electromagnetic radiation. This paper, based on theoretical analysis and experimental data, holds the view that electromagnetic radiation is generated by the high-temperature thermal effect. It studies the relationship between temperature and electromagnetic radiation and obtains quantitative analysis conclusions.

The objective of this paper is to present an electromagnetic sensor that generates pulse inductance [1], integrated on an Unmanned Aerial Vehicle (UAV) which complements the current technology in this area, adding equipment to the detection of landmines. The electromagnetic sensor developed, locates landmines deployed during armed conflicts, which daily kill innocent people, block economic and social development, hinder the displacement of people, causing serious social and economic problems for many years. Flights can be made over mined areas allowing the identification of the exact location of each land mine.

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

This study delves into the intricate relationships among the constituent elements, wave speed, and energy of both mechanical waves and electromagnetic waves. By establishing connections with the string vibration equation, a compelling revelation emerges. Upon equating the energy and constituent element mass of one wave cycle of a homogeneous string with those of a single wave cycle of electromagnetic waves, it is evident that the wave speed derived from the string vibration equation consistently matches the constant speed of light. From this, a hypothesis takes root: electromagnetic waves manifest as waves resulting from the vibration of a uniform, elongated string-like material. The phenomenon of superluminal speed further fortifies the validity of this conjecture.

Electromagnetic actuation can support many fields of technology, such as robotics or biomedical applications. In this context, fully understanding the system behavior and proposing a low-cost package for feedback control is challenging. Modeling the electromagnetic force is particularly tricky because it is a nonlinear function of the actuated object’s position and coil’s current. Measuring in real time the position of the actuated object with the precision required for accurate motion control is also nontrivial. In this study, we propose a novel, cost-effective electromagnetic set-up to achieve position control via visual feedback. We actuate vertically and under different experimental conditions a 10 mm diameter steel ball hanging on a low-stiffness spring, demonstrating good tracking performance (the position error remains within ±0.5 mm with a negligible phase delay in the best scenarios). The experimental results confirm the feasibility of the proposed set-up, which is characterized by minimum complexity and realized with off-the-shelf and cost-effective components. For these reasons, such a contribution helps to understand and apply electromagnetic actuation even further.

In this study, the temporal variation in soil salinity dynamics was monitored and analyzed using Electromagnetic Induction (EMI) in an agricultural area in Port Said, Egypt, which is at risk of soil salinization. To assess soil salinity, repeated CMD2 soil apparent electrical conductivity (ECa) measurements were taken and inverted to generate electromagnetic conductivity imaging (EMCI), representing soil electrical conductivity (σ) distribution through time-lapse inversion. This process involved converting EMCI data into salinity cross sections using a site-specific calibration equation that correlates σ with the electrical conductivity of saturated soil paste extract (ECe) for the collected soil samples. The study was performed from August 2021 to April 2023, involving six surveys during two agriculture seasons. The results demonstrated the accurate prediction ability of soil salinity with R2 value of 0.81. The soil salinity cross sections generated on different dates observed changes in the soil salinity distribution. These changes can be attributed to shifts in irrigation water salinity resulting from canal lining, winter rainfall events, and variations in groundwater salinity. This approach is effective for evaluating agricultural management strategies in irrigated areas where it is necessary to continuously track soil salinity to avoid soil fertility degradation and a decrease in agricultural production and farmer’s income.

The paper is focused on numerical modeling of multi-strand cable lines placed in free air. Modeling is carried out within the framework of the so-called multi-physics approach using commercial software. The paper describes in detail the steps undertaken to develop realistic, reliable numerical models of power engineering cables, taking into account their geometries and heat exchange conditions. The results might be of interest to the designers of multi-strand cable systems.

Recently, Bennett et al. [Eur. J. Phys. 37:014001, 2016] presented a physically-motivated and explicitly gauge-independent scheme for the quantisation of the electromagnetic field in flat Minkowski space. In this paper we generalise this field quantisation scheme to curved spacetimes. Working within the standard assumptions of quantum field theory and only postulating the physicality of the photon, we derive the Hamiltonian, $\hat H$, and the electric and magnetic field observables, $\hat {\bf E}$ and $\hat {\bf B}$, without having to invoke a specific gauge. As an example, we quantise the electromagnetic field in the spacetime of an accelerated Minkowski observer, Rindler space, and demonstrate consistency with other field quantisation schemes by reproducing the Unruh effect.

As we all know, contemporary electromagnetic theory is based on the macroscopic electromagnetic theory established by the 19th century. Because of the lack of microscopic cognition in that era, various electromagnetic phenomena could only be explained and described at the macro level, and their origins could not be explained at the micro level. And because of the microscopic understanding of atomic physics in the 20th century, new progress has been made. Considering that it is now the 21st century, this paper attempts to establish a new theory of microscopic interpretation of classical electromagnetic theory based on the new cognition of atomic physics in the 20th century. Starting from the general assumption, the current will be interpreted as the momentum flow produced by the directed collision between electrons; the charge will be interpreted as a form of expression of electron motion; the voltage is interpreted as the potential difference (energy level difference) of the electron orbit. In the end, this paper successfully developed a new microscopic electromagnetic theory by introducing microscopic atomic physics and rigid body mechanics models to Maxwell's macroscopic electromagnetic theory.

A novel method proposed in the production of Calophyllum inophyllum biodiesel has been investigated experimentally. In this study, we report the results of biodiesel processing with electromagnetic induction technology. The method used is to compare the results of Calophyllum inophyllum biodiesel processing between conventional, microwave and electromagnetic induction. The degumming, transesterification, and esterification process of the 3 methods are measured by stopwatch to obtain time comparison data. Characteristics of viscosity, density, and Fatty Acid Metil Ester (FAME) were obtained from testing of a Gas Chromatography-mass Spectrometry (GCMS) at the Polytechnic Chemistry Laboratory of the State of Malang. The results show that the biodiesel produced by this method satisfies the biodiesel standards and their characteristics are better than the biodiesel produced by conventional and microwave methods. The electromagnetic induction method also offers a fast and easy route to produce biodiesel with the advantage of increasing the reaction rate and improving the separation process compared to other methods. This advanced technology has the potential to significantly increase biodiesel production with considerable potential to reduce production time and costs.

In this paper analyses the characteristic of EM waves propagation in structured environment to identify the signal interference by the structure, and suggests the EM waves attenuation model considering the distance and penetration loss by the structure. The range sensor based on electromagnetic(EM) waves attenuation along to the distance showed the precise distance estimation with high resolution depending on the distance. However, it is hard to use in structured environments due to the lack of consideration of the EM waves attenuation characteristics in the structured underwater environment. In this paper, EM waves propagation characteristic and signal interference effects by the structures were analyzed, and the EM waves distance-attenuation model in structured environment was suggested with sensor installation guideline. The EM waves propagation characteristics and proposed sensor model were verified by the several experiments, and the localization result in structured environment showed the more reliable performance.

In this paper, an original approach allowing the determination of the iron losses in the electromagnetic devices is presented. This new approach exploits the Loss Surface (LS) hysteresis model and the magnetic flux density waveforms resulting from a generalized nonlinear adaptive magnetic equivalent circuit (MEC) using a mesh-based formulation in two-dimensional (2-D) or quasi three-dimensional (3-D). The model coupling has been applied to a 18-slots/16-poles radial-flux interior permanent-magnet (PM) synchronous machine (PMSM) dedicated to automotive applications, mainly for electric/hybrid/fuel cell vehicles (EVs/HEVs/FCVs). The obtained results have been compared with those made retrospectively in the 2-D transient finite-element (FE) Flux. The influence of the MEC discretization on the iron loss calculation and the electromagnetic performances has been analyzed. The computation time is divided by 3/2 with an error less than 7 %.

We consider the Dirac electron as a nonperturbative particle-like solution consistent with its own Kerr-Newman (KN) gravitational and electromagnetic field. We develop the earlier models of the KN electron regularized by Israel and López, and consider the non-perturbative electron model as a bag model formed by Higgs mechanism of symmetry breaking. The López regularization determines the unique shape of the electron in the form of a thin disk with a Compton radius reduced by 4π. In our model this disk is coupled with a closed circular string which is placed on the border of the disk and creates the caused by gravitation frame-dragging string tension produced by the vector potential of the Wilson loop. Using remarkable features of the Kerr-Schild coordinate system, which linearizes the Dirac equation, we obtain solutions of the Dirac equation consistent with the KN gravitational and electromagnetic field, and show that this solution takes the form of a massless relativistic string. Parallelism of this model with quantum representations in Heisenberg and Schrodinger pictures explains remarkable properties of the stringy electron model in the relativistic scattering processes.

To improve the current density distribution and electromagnetic performance of air-core inductors, a structural optimization method combining BP neural network and genetic algorithm was proposed for the study of axial and radial spiral multi-winding inductors. The Monte Carlo method was used to extract the structural size samples of the inductors, and the training dataset was obtained through finite element calculation of electromagnetic fields. Based on BP neural networks, nonlinear mapping models between the inductance value, volumetric inductance density, current distribution non-uniformity coefficient, and inductor structural parameters were constructed. The sensitivity analysis of the inductor inductance value affected by structural parameters was conducted through the Sobol index calculation. Using the current distribution non-uniformity coefficient as the fitness function and the volumetric inductance density as the constraint condition, the genetic algorithm was applied to optimize the structural parameters of the inductor globally. The optimization results were verified through finite element comparison. The results show that, under the requirement of satisfying the volumetric inductance density, the current distribution non-uniformity coefficient of AHI type inductor was reduced by 4.57% compared with the best sample in the sampling, while that of RHI type inductor was reduced by 5.33%, demonstrating the practicality of the BP-GA joint algorithm in the structural optimization design of inductors.

Boron carbide (B4C) powders with defined stoichiometry, high crystallinity, minimal impurity content, and a fine particle size are imperative for realizing the exceptional properties of this compound in advanced high-technology applications. Nevertheless, achieving the desired stoi-chiometry and particle size using traditional synthesis methods, which rely on prolonged, high-temperature processes, can be challenging. The primary objective of this study is to syn-thesize fine B4C powders characterized by high crystallinity and a sub-micron particle size, em-ploying a fast, and energy-efficient method. B4C powders are synthesized from elemental boron and carbon in a high-frequency induction heating furnace using the Electromagnetic Induction Synthesis (EMIS) method. The rapid heating rate achieved through contactless heating promotes the ignition and propagation of the exothermic chemical reaction between boron and carbon. Additionally, electromagnetic effects accelerate atomic diffusion, allowing the reaction to be completed in an exceptionally short timeframe. The grain size and crystallinity of B4C can be finely tuned by adjusting various process parameters, including the post-ignition holding temperature and the duration of heating. As a result, fine B4C powders can be synthesized in under 10 minutes. Moreover, these synthesized B4C powders exhibit high resistance to oxidation when exposed to air.

Nondipole terms in the atom-laser interaction arising due to the presence of a magnetic component in an electromagnetic wave and its inhomogeneity lead to nonseparability of the center-of-mass (CM) and electron variables in the neutral atom and, as a consequence, to its acceleration. We investigate this effect as well as the accompanying excitation and ionization processes for the hydrogen atom in strong (1012 - 2×1014 W/cm2) linearly polarized short-wavelength (5eV ≲ℏω≲ 27 eV) electromagnetic pulses of about 8 fs duration. The study has been carried out within the framework of a hybrid quantum-quasiclassical approach in which the coupled time-dependent Schrödinger equation for an electron and the classical Hamilton equations for the CM of an atom are simultaneously integrated. Optimal conditions with respect to the frequency and intensity of the electromagnetic wave for the acceleration of atoms without their noticeable ionization are found in the analyzed region.

High-performance electromagnetic interference (EMI) shielding materials with ultralow density and environment friendly properties are greatly demanded to address electromagnetic radiation pollution. Herein, carbon nanotubes/polylactic acid (CNTs/PLA) materials with different CNTs contents, which exhibit characteristics of light weight, environmental protection and good chemical stability, are fabricated by 3D printing technology, where CNTs are evenly distributed and bind well with PLA. The performances of 3D printed CNTs/PLA composite are improved compared to pure 3D printed PLA composite, which include mechanical properties, conductive behaviors and electromagnetic interference (EMI) shielding. The EMI shielding effectiveness (SE) of CNTs/PLA composite could be improved when the contents of CNTs increase. When it reaches 15 wt%, the EMI SE of 3D printed CNTs/PLA composite could get up to 47.1 dB, which shields 99.998% of electromagnetic energy. Meanwhile, the EMI shielding mechanism of 3D printed CNTs/PLA composite is mainly of absorption loss, and it generally accounted for more than 80% of the total shielding loss. These excellent comprehensive performances endow the 3D printed CNTs/PLA composite with great potential for use in industrial and aerospace area.

When in operation, the 25 kV traction networks may encounter the contact wire short circuits to rails or ground. The short-circuit conditions cause high-intensity magnetic fields (EMFs), which, despite the short duration of exposure, can negatively affect electronic devices and lead to significant induced voltage on adjacent power lines. There can be two main types of emergency conditions in 25 kV traction networks: the contact wire short circuit to the rail, when the supports are grounded to the rail track; and the contact wire short circuit to the ground in sections with supports disconnected from the rails. A three-dimensional electromagnetic field near a metal support when a short-circuit current flows through it is characterized by a complex spatial structure, which significantly complicates the calculations of intensities. The paper discusses the results of computer modeling aimed at determining the EMF intensity in the described emergencies. The objects involved in modeling were represented by segments of thin wires to calculate the electric charge distribution and find out the EMF intensity. This approach is implemented in the Fazonord software. The modeling results have shown that EMF intensities near the support grow significantly; their levels decrease noticeably as one moves away from the support; and that the three-dimensional electromagnetic field under the considered emergency conditions has a complex spatial structure.

We present here a five hours experimentation of a didactical path about the electromagnetic induction addressed to students of the last year of an Italian scientific high school and oriented to better understand the physical origin of the induced electromotive force. The expression of the induced electromotive force as the sum of the term linked to the time variation of the magnetic field and of the motional one has been obtained in a detailed way, still suitable for presentation at high school. Many examples have been proposed to the students in order to clarify the conceptual physical knots. The students’ responses to a 6-questions multiple choice questionnaire have been analyzed. It emerged that our approach is concretely feasible although we find the well-known difficulties in calculating flux and circulation of a vector field. Furthermore, it emerged that an integral approach to the problem masks the understanding of the nature of the forces acting locally on the charges. Hence our proposal of a “redefinition” of the induced electric field in terms of the magnetic vector potential is also presented.

In this paper, we considered two phenomena in acoustically excited aqueous solutions of a strong electrolyte. These are the well-known Debye ionic vibrational potential (IVP), and radiofrequency anisotropy we discovered earlier , apparently, for the first time. Since both occur due to the accelerated motion of the solution, we have tried to combine them in one simple model. We have established that for a polarized UHF radio wave passed through a NaCl aqueous solution excited by an acoustic pulse the rotation angle of its vector E is proportional to the integral of the square of the observing IVP over time. An equivalent electrical circuit simulating the observed phenomena has been proposed and tested for physical feasibility. Several arguments are given in favour of the fluid-gyroscopic mechanism of RF anisotropy-related effects. We also found out that the IVP is practically independent of the vibrational velocity for frequencies below 10 kHz and it tends to zero at zero frequency. The latter is consistent with the law of conservation of energy but contradicts the incomplete existing theory.

This work presents an alternative to harnessing wind energy with an Electromagnetic Frequency Regulator (EFR) coupled to a hydrostatic transmission and associated with a horizontal axis wind turbine, a bidirectional frequency inverter and a secondary energy source, in a hybridized system. The hydrostatic transmision is composed by a fixed displacement axial piston pump and a variable displacement, swash plate, axial piston motor. Feedback linearization was used as a technique to control the motor geometric displacement, and a prediction algorithm for the steady state rotations of the armature and the electromagnetic field has been developed. A 5\,kW project was simulated on a Scilab platform, with combinations of constant or variable load, and constant or variable wind speed. The results indicated that the system was able to supply the generator load, adapting to fluctuations in wind speed. The possibility of storing wind energy through the inverter has also been proven. The system can accumulate energy in batteries during the fastest wind regimes, to use it when the turbine power is lower than the load.

Theoretical analysis into the energetics of a novel putative electromagnetic field propulsion device by the author, found that it was able to impart momenergy to the ground state of the electromagnetic field; some rest-energy of the craft was converted to kinetic energy of the craft. Electrical analysis showed that the propulsor was always a net electrical load – if the device accelerated from one frame, then deaccelerated to the original frame, both processes would consume electrical work. The aim of this paper is to look further into this sinking of high-grade electrical energy into the field ground state and to show that an even more pernicious form of 2^nd Law of Thermodynamics exists.

Background: biophysical stimulation therapy, and in particular Pulsed Electromagnetic Fields (PEMFs) and capacitively coupled electric fields (CCEFs) has significantly increased in the last twenty years. For this, it is necessary to have clear information regarding the efficacy, the therapeutic indication and the expected objectives. Methods: we conducted a narrative review taking into consideration different types of studies with different areas of application. The objective was to take into consideration and analyze the different fields of use and the relevant information present in the literature. Results: There is unanimous opinion regarding the usefulness of applying biophysical therapy on the bone compartment both in terms of the tissue healing process and the symptoms associated with this situation. Differently, but no less importantly, in the joint compartment positive opinions were observed mainly on the inflammatory and catabolic process, however, at present,we did not report evidence regarding cartilaginous tissue regeneration. Conclusion: the effectiveness of PEMFs and CCEFs on the bone healing process in the Orthopedic and Traumatology fields is consolidated evidence in the literature. We have also found positive results on symptoms and patient compliance with rehabilitation therapies. Therefore, notable application can be envisaged in the fields of Prosthetic Surgery and Sports Medicine.

The two-scale method (TSM) is an effective approach to simulate electromagnetic (EM) scattering from rough sea surface, to interpret physical interaction of EM wave with rough sea surfaces. The sea surface roughness spectrum and the cutoff wavenumber are two key factors affecting the accuracy of TSM simulation. This paper takes the geophysical model functions (GMFs) of different band as reference, and quantitatively studies the two factors based on the numerical simulation of different polarization backscattering coefficients. The numerical simulation demonstrates that Apel spectrum is more suitable for the backscattering simulation in C/X/Ku-band, and the optimal cutoff wavenumbers are also derived for TSM simulation of EM scattering in C/X/Ku-band. Then an empirical model function of optimal cutoff wavenumbers with respect to frequency, incident angle and wind speed are obtained with regression method. Finally, the simulation results with the new model function of cutoff wavenumber are compared with the GMF and measured data in different bands and they are all consistent. Moreover, a physical explanation for the optimal cutoff wavenumber is also given.

Managing sidelobe levels (SLLs) in metasurface-driven beam-steering antennas poses a significant challenge due to intrinsic factors leading to grating lobes. Our proposed method employs an equivalent model to optimize large periodic metasurfaces efficiently. This model predicts complete metasurface performance, accounting for mutual coupling between patches. We introduce an evolutionary optimization algorithm based on the Cross Entropy (CE) method to enhance PGM-based beam-steering antennas and suppress sidelobes. Two strategies were employed: first is to optimize the patch dimensions for a sidelobe-free pattern and the second is to maintain the PGM dimensions while optimizing feed array amplitudes. Both strategies effectively suppressed sidelobes, offering insights into the CE method's applicability and effectiveness for CPU-intensive electromagnetic optimization challenges. The proposed CE method variant retains its simplicity while improving monitoring capabilities, addressing this limitation. Smaller generations yield better improvements per evaluation

The paper is dedicated to the topical problem of examining permafrost state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we propose and scientifically substantiate a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings and constructions.

The authors of the paper have made an attempt to detect the fibre content and fibre spacing in a steel fibre reinforced concrete (SFRC) industrial floor. Two non-destructive testing (NDT) methods: an electromagnetic induction technique and a radar-based technique were applied. The first method allowed to detect the spacing in subsequent layers located in the thickness of the slab. The result of the second method was a 3D visualization of the detected fibre in the volume of concrete slab. The conducted tests showed aptitude and limitations of the applied methods in estimating fibre volume and spacing. The two techniques also allowed to locate the areas with relatively low fibre concentration which are very likely to be characterized by low mechanical properties.

This conceptual paper explores the potential of integrating Electromagnetic Fields (EMF) with traditional physiological signals to enhance emotional contagion in Human-Robot Interaction (HRI). A focused literature review identifies gaps in current HRI models that rely solely on visual, auditory, and known physiological cues for emotional exchange. A novel framework is proposed, incorporating EMF as a complementary modality, aiming to deepen emotional synchronization between humans and robots. The paper lays groundwork for future research to consider EMF detection as a complementary modality alongside traditional cues. It also addresses technological requirements and discusses potential limitations. By extending the modalities used in emotional contagion, this work seeks to advance the development of more intuitive and empathetic robotic systems.

Electronic devices are sensitive to electromagnetic (EM) emissions requiring electromagnetic shielding protection to assure good operation, preventing noise, malfunctioning, or even burning. To assure protection, it is important to develop suitable material and design solutions for electronic enclosures. Most common enclosures are made with metal alloys by traditional manufacturing methods. However, resourcing to thermoplastic composites combined with additive manufac-turing (AM) technologies emerges as an alternative that enables to fabricate complex parts that are lightweight, consolidated and oxidation and corrosion resistant. In this research, an AM technique based in material extrusion was used to print 2 mm thick specimens with a multi-material made of micro-carbon fiber (CF) filled polyamide, reinforced, at specific layers, by continuous carbon fibers stacked with a 90° rotation to each other. Specimens electromagnetic shielding effectiveness (EMSE) was evaluated in the frequency band of 0.03 – 3 GHz by coaxial transmission line method. De-pending on the number of CF layers, the EM shielding obtained can up to 70 dB, with a specific shielding up to 60 dB.cm3/g, predominantly by absorption mechanism, being 22 times higher that without the CF layers. These findings fundament this innovative approach for lightweight cus-tomizable solutions for EM shielding applications.

This study presents a tri-layer broadband metamaterial absorber which operates in the GHz range. The absorber was composed of a polyhedral iron-cobalt alloy/graphite nanosheet material arranged in a flat sheet with two punched-in rings for the top layer, a continuous FR-4 layer at the middle, and a continuous copper layer at the bottom. For the normal incidence of electromagnetic wave, the proposed absorber demonstrated an exceptional broadband absorption in a frequency range of 7.9-14.6 GHz, revealing an absorption exceeding 90%. The absorption magnitude remains to be above 90% in a frequency range of 8-11.1 GHz for transverse-electric-polarized waves at incident angles up to 55°. For both transverse-magnetic- and electric-polarized waves, the absorption exceeds 90% in a frequency range of 9.5-14.6 GHz. The physical mechanism behind the absorption properties is analyzed thoroughly through the electric- and magnetic-field distributions. The obtained results could contribute potentially to the development of microwave applications based on metamaterial absorbers, such as radar-stealth technology, electromagnetic shielding for health safety and reduced electromagnetic interferences for high-performance communications and electronic devices.

In this paper a high-power and propellant-free electromagnetic propulsion is proposed based on the General Relativity and nuclear fusion technology. We find that Riemann curvature vanish and geodesic motion is free from gravitational field locally in a special space-time, which demonstrates the feasibility of propellant-free electromagnetic propulsion. To achieve high-power propulsion in Schwarzschild background, we choose current loop as axisymmetric field source and obtain exact solution of Einstein-Maxwell field equation using Killing symmetry and Ernst generation technique. An implementation with superconductor shield is given according to the Meissner effect, calculation implies that the device can be sufficiently free from gravitational field with the aid of existing nuclear fusion engineering.

Sediment thickness increases can cause floodplains and the water level increases. This has the potential to generate a flood. Using electromagnetic waves, Time Domain Electromagnetic (TDEM) detected resistivity or conductivity contrast of lithology in the subsurface. It is measured in the time domain. TDEM method has been developing for decades. Here we tried to develop a 1-D forward modelling program for central loop configuration in the water environment using the Adaptive Born Forward Mapping (ABFM) method. We simulated this program in several water environment conditions (such as freshwater, brackish water and saline water) to know its response. Preventing natural hazards, especially flood hazards which are caused by the floodplain increases is our motivation in this research. Our simulation shows that Central-Loop Configuration Time-Domain Electromagnetic Method is able for imaging the sediment thickness clearly. The response of this method is extremely sensitive in saline water to depth changing than in other water environments.

To realize structural vibration control,a two parameters H2 optimization design was proposed to optimize the tuning ratio and damping ratio for electromagnetic tuned mass damper (EMTMD). The control effect of this two parameters optimization design is better than that of classical tuned mass damper (TMD).For this two parameters optimization,the most important thing is that the inductance of the coil can be set very small and the external load resistance can be positive ,which can avoid the use of complex negative impedance circuit. If Ref.[6] were designed according to the H2 optimization of two parameters, the EMTMD can be used for multi-modal vibration control of structures without connecting negative inductance and negative resistance spontaneously.

Three-phase to single-phase matrix converter (TSMC) is used as the transmitter for transient electromagnetic method (TEM) instrument, instead of an AC-DC converter and an H-bridge inverter. The transmitter produces excitation current for primary field. The output current has a waveform with a bipolar square of half duty cycle, which is required by TEM. The space vector PWM based on input currents is discussed in detail. The control method of input power factor is proposed for TSMC. The simulation model of TSMC is established and the simulations of different conditions are completed. The simulation results show the controllability of the input power factor is illustrated.

In this paper, we investigated the capacitive effect and the electromagnetic coupling on the measurement chain induced by the gas gun or the powder gun during impact experiments. Reduced bandwidth and noise have been noticed on experimental signals. Rogowski coil measurements have been added on the cables to characterize the electromagnetic coupling. The perturbation currents on the cables have been quantified depending on the configuration. The gauge, the transmission line and the conditioning system have been modeled. The calculations have reproduced the electrical wave arrival time, the transmission line transfer impedance, the conditioning system transfer impedance and it shows the bandwidth limitation. A capacitive effect with the piezoresistive manganin gauge embedded into the sample has been identified depending on the experimental setup.

In our previous papers [1,3], using only the concepts of the zero-point energy and quantized space–times, all the fields including gravity were explained. However, the previous papers had the following limitations: First, the concept of the quantized space-time must be experimentally confirmed. Second, we should clarify the meaning of the quantized Einstein’s gravity equation, which is derived in [1]. Moreover, in another paper [2], we succeeded in describing the neutrinos’ self-energy and their oscillations. However, this paper assumes the rest energy of 3-leptons in advance, which is why we needed to uncover the reason why leptons have 3-generations. As mentioned, using the concepts of the zero-point energy and quantized space–times, we derived the quantized Einstein’s gravity equation in our previous paper [1]. The paper provides an analytical solution of this equalized Einstein’s equation, which implies the conservation of angular momentum in terms of quantized space–times. Employing this solution and without the standard big bang model, a unique form of acceleration equation for the acceleration-expansion universe is derived. Moreover, the temperature of the cosmic microwave background (CMB) emission is also obtained. Further, this solution results in an analytical (not numerical) derivation of the gravity wave. Moreover, based on the configuration of quantized space–times in terms of both electric and magnetic fields, we analytically attempted to calculate every equation in terms of electromagnetic and gravity fields, using the solution of the quantized Einstein’s gravity equation. As a result of this theory, first the calculated acceleration and temperature of CMB emission agree with the measurements. Furthermore, the analytical solution of the quantized Einstein’s gravity equation resulted in all the laws of electromagnetic and gravity fields in addition to the analytically derived gravity wave, which agrees well with the recent measurements. Moreover, the calculations of the energies in the basic configuration of the quantized space–times resulted in all 3-leptons’ rest energies. Considering this basic configuration is uniformly distributed everywhere in the universe, we can conclude that τ-particles or static magnetic field energy derived from the basic configuration of the quantized space–times is the identity of dark energy, which also distributes uniformly in the universe.

Among all the processing technologies of heat-treatable aluminum alloys like 2219 aluminum alloy, using friction stir welding (FSW) as the joining technology and using electromagnetic forming (EMF) for plastic forming technology both have obvious advantages and successful applications. Therefore, there is a broad prospect for the compound technologies which can be used on the 2219 aluminum alloy to manufacture the large-scale thin-wall parts in the astronautic industry. The microstructure and mechanical properties of 2219 aluminum alloy under the process compounded of FSW, heat treatment, and EMF were investigated by means of tensile test, optical microscope (OM), and scanning electron microscope (SEM). The results show that the reduction of strength, which was caused during the FSW process, can be recovered effectively by the post-welding heat treatment composed of solid solution and aging, while the ductility was still reduced after heat treatment. Under the compound technology of FSW, heat treatment, and EMF, the forming limit of 2219 aluminum alloy decreased distinctly due to the poor ductility of the welding joint. A ribbon-pattern, which was formed due to the banded structure caused by FSW process, was found on the fracture surface of welded 2219 aluminum alloy after EMF treatment. During the EMF process, because of the effects of induced eddy current, a unique structure, which was manifested as a molted-surface appearance under the SEM observation, was formed as the material fractured.