Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

Exergy analysis evaluates the efficiency of system components by quantifying the rate of entropy generation. In general, the exergy destruction rate or irreversibility rate was directly obtained through the exergy-balance equation. However, this method cannot determine the origin of the component's entropy generation rate, which is a very important factor in system design and improvement. In this study, a thorough energy, exergy thermoeconomic analysis of a proton exchange membrane fuel cell (PEMFC) was performed, providing the heat transfer rate, entropy generation rate and cost loss rate of each component. The irreversibility rate of each component is obtained by the Gouy-Stodolar theorem. Detailed and extensive exergy and thermoeconomic analyses of PEMFC system have determined that water cooling units experience the greatest heat transfer among the components in the studied PEMFC system, resulting in the greatest irreversibility and thus the greatest monetary flow loss.

To decrease privacy risks, consumers may choose to misrepresent when they are asked to offer personal information. This paper examines the impact of consumer misrepresentation on a monopolistic firm and consumers with an economic model. The results show that consumer misrepresentation may benefit the firm but hurt consumers. In addition, consumers misrepresentation may encourage the firm to provide higher personalized service level in certain scenarios, such as, when the unit cost of personalized service is low. Thirdly, when consumers misrepresent, and the firm only covers part of the market, a greater unit value of consumer’s privacy information will reduce the firm’s profit, but a greater unit cost of personalized service increases the firm’s profit.

The installation of electric vehicle supply equipment (EVSE) increases demand and peak loads, potentially straining existing energy distribution infrastructure. Dispersed and inadequately planned placement of charging points (CPs) can disrupt the electrical grid, surpass contracted demand thresholds, and require infrastructure upgrades, thereby incurring unfeasible costs for Distribution System Operators (DSOs). In this context, it is necessary to recognize the role of business models in enabling effective electrification of the transportation sector. In response to these challenges, this paper introduces a novel e-mobility hub management strategy, tailored for implementation in the Brazilian context. The proposed strategy revolves around a microgrid configuration encompassing dispatchable and photovoltaic generation, a battery energy storage system (BESS), EVSE infrastructure, and local loads. Moreover, this centralized controller facilitates the implementation of dynamic pricing and demand-response mechanisms, integral to business models seeking to integrate EVSE into the distribution grid. To validate the efficacy of the proposed solution, hardware-in-the-loop (HIL) simulations of the microgrid system are conducted. These simulations, incorporating the centralized controller, serve as a tool for assessing system performance and viability before on-site equipment deployment. Finally, this paper concludes with the insights gleaned from test analysis and its discussion through a selection of the most expressive scenarios, including islanded and connected operation modes.

This study investigates the impact of circular economy (CE) strategies on organizational resilience (OR) within the metal industry, focusing on a case study of a forging department in a large man-ufacturing company. The idea of the paper is to link the macroeconomic topic of circular economy (CE) with microeconomic and practical activities in the organization, exploring how CE principles can improve resource efficiency, sustainability, and organizational resilience. A systematic literature review and case study methodology were used to assess the relationship between CE and OR. The findings reveal that companies with higher circularity demonstrate better resilience, both in normal operations and during crises. Specifically, in the case study, the closure of the forging department, following a detailed analysis using the Inputs-Mediators-Outputs (IMO) model, emerged as the most sustainable option, yielding financial, environmental, and operational benefits. This decision aligned with the company’s long-term goals of energy efficiency and carbon neutrality. The research highlights the significance of integrating CE strategies with business processes to not only achieve sustainability but also to build a more adaptable and resilient organization. Future research should explore broader applications of this framework across different industries to strengthen the links between circular economy practices and organizational resilience.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

The wellness economy has developed rapidly recently, particularly in wellness tourism. Wellness tourism transforms sustainable strategy through the availability of extended multi-actor engagement in service innovation to further the tourism experience. Therefore, when operating a wellness tourism destination, it is necessary to encourage multi-actor engagement in service innovation to achieve sustainable development. This paper introduces a mixed research method with the SWOT-AHP-QSPM, as it qualitatively analyzes the advantages, disadvantages, opportunities, and threats, constructs an evaluation index system, conducts quantitative analysis using the analytic hierarchy process, determines the index weight and weighted score, and calculate the sustainable development strategy, which is appropriate for wellness development of Chongqing Tea Mountain and Bamboo Forest National Forest Park. Purposive field surveys and personal interviews were conducted in Chongqing forest tourism destinations, involving 356 effective respondents. The research reveals that multi-actor engagement significantly enhances sustainable development. These findings bridge service innovation knowledge gaps and provide valuable insights for forest tourism destination management and sustainable policy strategies to elevate multi-actor engagement in forest sites.

The purpose of this article is to present an IoT architecture implemented in an intelligent environment, focusing on the optimization of initial conditions and device management. A general control system was developed using an open-source platform, integrating aWi-Fi network and YAML coding to enable communication and control of the IoT architecture devices. The implementation includes actuators, sensors, and control devices that, through a graphical interface, allow the visualization of the historical record of activities and real-time measurements of connected devices. The design includes specific mechanisms and the analysis of materials through tensile tests on specimens, following the ASTM E8 standard, and deformation test simulations, in which PLA demonstrated better performance compared to materials like ABS and resin. The significance of the implemented IoT system lies in an energy saving of 58% compared to conventional structures. Additionally, the study of response times for network connections showed that using an Ethernet cable resulted in a response time of 1.21 seconds, representing a reduction of 1.65 seconds compared to the second lowest value obtained.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

Innovation is an essential key factor in the technology development history. Past research on innovation focused more on the innovation behavior of technology, but seldom described knowledge assets which also influence innovation behavior greatly. The effect of knowledge assets attribute and result on disruptive innovation is therefore regarded as the research topic in this study, where disruptive innovation is divided into outbound and inbound to combine combination-embeddednessandmajor business specificityof knowledge assets as the research model. Manufacturing enterprises in China are proceeded the questionnaire survey, and 173 valid copies are collected. The empirical analysis shows that combination-embeddedness of knowledge assets presents significantly positive effects on major business specificity and outbound innovationof an enterprise but reveals remarkably negative effects on inbound innovation. Enterprises are suggested to constantly accumulate knowledge assets with low major business specificity before disruptive innovation in order to reduce ineffective inbound innovation.

The growing use of proton-exchange membrane fuel cells (PEMFC) in hybrid propulsion systems, aimed at replacing traditional internal combustion engines and reducing greenhouse gas emis-sions. Effective power distribution between the fuel cell and the energy storage system (ESS) is crucial, which has led to a growing emphasis on developing energy management systems (EMS) to efficiently implement this integration. To address this goal, this study examines the performance of a fuzzy logic rule-based strategy for a hybrid fuel cell propulsion system in a small hydro-gen-powered passenger vessel. The primary objective is to optimize fuel efficiency, with particular attention to reducing hydrogen consumption. The analysis is carried out under typical operating conditions encountered during a river trip. Comparisons between the proposed strategy with other approaches —control-based, optimization-based and deterministic rule-based— are con-ducted to verify the effectiveness of the proposed strategy. Simulation results indicated that EMS based on fuzzy logic mechanisms was the most successful in reducing fuel consumption. The superior performance of this method stems from its ability to adaptively manage power distri-bution between the fuel cell and energy storage systems.

The purpose of this paper is to examine the role and impact of public governance on European supranational public policies that seek to foster scientific and economic growth within innovation ecosystems (IEs) through the PITCCH initiative. The PITCCH is a European innovation development initiative funded by Horizon 2020 under the 'Innovation in SMEs' measure.The research methodology for this study is based on a 10-month real-time ethnographic field study of the PITCCH project, which allowed for the observation of the project governance and the capture of the perspectives of innovation-driven small and medium enterprises (i-SMEs) in their engagement with IE stakeholders.The findings of this research demonstrate the role of public governance in providing result-oriented practical support to the IE through the lens of i-SMEs, and they contribute to the existing literature on regional economic growth supported by supranational public policies. These findings have both academic and practical applications. They enrich the current literature on this topic and provide insights for policymakers and governing representatives seeking to implement effective public policies.

To evaluate the used and End-of-Life tyre management chains, both direct observation and interviews with approximately 200 used-tyre dealers were conducted. The study revealed that while the used tyre business is well-organized, End-of-Life tyre treatment is nearly non-existent, often involving dumping, open burning for metal recovery, or use in meat processing, causing environmental and health risks. To address these challenges, an 8 t/hr capacity tyre recycling plant is planned, based on estimated tyre availability and development opportunities for sustainable recycling in Togo.

Proper management of solar energy, as an effective renewable source, is of high importance toward sustainable energy harvesting. This paper offers a novel sophisticated method for predicting solar irradiance (SIr) from environmental conditions. To this end, an efficient metaheuristic technique, namely electromagnetic field optimization (EFO) is employed for optimizing a neural network. This algorithm quickly mines a publicly available dataset for non-linearly tuning the network parameters. To suggest an optimal configuration, five influential parameters of the EFO (i.e., N_Pop, R_rate, Ps_rate, P_field, and N_field) are optimized by an extensive trial and error practice. Analyzing the results showed that the proposed model can learn the SIr pattern and predict it for unseen conditions with high accuracy. Furthermore, it provided about 10% and 16% higher accuracy compared to two benchmark optimizers, namely shuffled complex evolution and shuffled frog leaping algorithm. Hence, the EFO-supervised neural network can be a promising tool for the early prediction of SIr in practice. The findings of this research may shed light on the use of advanced intelligent models for efficient energy development.

Against the backdrop of the European Union's commitment to achieve climate neutrality by 2050, efforts to improve energy efficiency are being intensified. The manufacturing industry is a key focal point of these endeavors due to its high final electrical energy demand, while simultaneously facing a growing shortage of skilled workers crucial for meeting established goals. Expert systems (ESs) offer the chance to overcome this challenge by automatically identifying potential energy efficiency improvements and thereby playing a significant role in reducing electricity consumption. This paper systematically reviews state-of-the-art approaches of ESs aimed at improving energy efficiency in industry, with a focus on manufacturing. The literature search yields 1668 results, of which 62 articles published between 1987 and 2024 are analyzed in depth. These publications are classified according to the system boundary, manufacturing type, application perspective, application purpose, ES type, and industry. Furthermore, we examine the structure, implementation, utilization, and development of ESs in this context. Through this analysis, the review reveals research gaps, pointing toward promising topics for future research.

This study aims to quantify greenhouse gas (GHG) emissions from China's sludge treatment industry and explore the potential of novel technologies to mitigate these emissions, promoting sustainable sludge management practices. Using a life cycle assessment approach, the total GHG emissions from sludge treatment in 2017 were estimated at 18.54 Mt CO2-eq, with significant regional variations. Incineration contributed the highest emissions (1,011.53 kg CO2-eq/t dry sludge), followed by landfill (717.51 kg CO2-eq/t) and land application (276.41 kg CO2-eq/t). The uneven distribution of emissions across cities highlights the need for targeted mitigation strategies that consider local sustainability challenges. Principal component analysis revealed that economic factors and treatment scale significantly influence emissions, emphasizing the importance of integrating sustainability goals with economic development. To reduce the carbon footprint of sludge treatment and enhance sustainability, the mitigation potential and costs of various technologies were evaluated, including thermal conversion, anaerobic digestion, hydrothermal processes, and wet oxidation. These technologies offer GHG emission reductions ranging from 0.09 to 0.46 t CO2-eq/t dry solids compared to conventional methods, while also promoting resource recovery and circular economy principles. However, further optimization is necessary to enhance their environmental and economic performance, ensuring long-term sustainability. By implementing these technologies and adopting optimization strategies, China's sludge treatment industry can significantly contribute to achieving the country's carbon neutrality goal and fostering sustainable development.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

Recycling information can be complex and often confusing which may subsequently reduce the participations in any waste recycling schemes. As a result, this research explored the roles as well as the importance of a holistic approach in designing recycling information using 15 expert-based in-depth interviews. The rationale was to offer a better understanding of what constitutes waste, recycling, and how recycling information should be designed and presented to make recycling more attractive/convenient. Based on the research participants’ perceptions with supports from the existing studies, this research sub-categorised recycling information into three different themes, termed the “WWW” of recycling information components. As a result, these components (or attributes) were extensively described (using findings of semi-structured interviews) to elicit pragmatic guidance for practitioners, policy-makers, and other stakeholders in designing structured communication or information strategies that may simplify and subsequently increase waste-recycling practices. The policy implications of holistic information in enhancing recycling are further discussed.

Despite energy-related financial concerns and the growing demand for sustainability, many energy efficiency measures are not being implemented in industrial practice. There are a number of reasons for this, including a lack of knowledge about energy efficiency potentials and the assessment of energy savings as well as the high workloads of employees. This article describes the systematic development of an expert system, which offers a chance to overcome these obstacles and contribute significantly to increasing the energy efficiency of production machines. The system employs data-driven regression models to identify inefficient parameter settings, calculate achievable energy savings, and prioritize actions based on a fuzzy rule base. Proposed measures are first applied to an analytical real-time simulation model of a production machine to verify that constraints required for the specified product quality are met. This provides the machine operator with the expert means to apply proposed energy efficiency measures to the physical entity. We demonstrate the development and application of the system for a throughput parts cleaning machine in the metalworking industry.

This paper aims at presenting an energy management strategy (EMS) based upon optimal control theory for a battery-supercapacitor hybrid power system. The hybrid power system consists of a Lithium-ion battery and a supercapacitor with associated bidirectional DC/DC converters. The proposed EMS aims at computing adaptive gains using salp swarm algorithm and load following control technique to assign the power reference for both the supercapacitor and the battery while achieving optimal performance and stable voltage. The DC-DC converter model is derived utilizing the first-principles method and compute the required gains to achieve the desired power. The fact that the developed algorithm takes disturbances into account increases the power ele-ments’ life expectancies and supplies the power system with the required power

This research is dedicated to a comprehensive examination of the strengths and weaknesses inherent in the legal and institutional measures designed to protect cultural heritage in the Republic of Serbia from the adverse effects of natural disasters, including earthquakes, landslides, rockfalls, floods, torrents, storms, hail, and forest fires. The study aims to identify the primary challenges and shortcomings within the existing legal and institutional framework, while also pinpointing and analyzing best practices and potential improvements for the protection system. This research posits a preliminary hypothesis suggesting that challenges may exist within the legal and institutional framework for the protection of cultural heritage in the Republic of Serbia, potentially limiting effective response and recovery following natural disasters. This hypothesis will be further developed and adapted based on the analysis of available data. Data collection for this research was conducted through semi-structured interviews with experts and an in-depth analysis of existing documentation. By conducting interviews with experts in the field, the research seeks to gather critical data and insights that will enhance the understanding of these issues and contribute to formulating viable solutions. The analysis and processing of data were carried out using ATLAS.ti software, which facilitated a comprehensive and systematic examination of the collected qualitative information. Furthermore, an assessment of the current capacity of institutions to respond rapidly and effectively to natural disasters that pose a threat to cultural heritage is a key component of the study. The ultimate goal is to develop recommendations that will fortify the legal and institutional framework, thereby bolstering the resilience of cultural heritage sites in Serbia against future natural disasters. The results of the research, highlight significant deficiencies in the legal framework, inadequate institutional capacities and resources, as well as a lack of proper training for crisis response. The need for improved inter-institutional cooperation and the development of technical-logistical resources is emphasized. This paper represents a significant contribution to the understanding and enhancement of the cultural heritage protection system, providing a foundation for further research and strategy development in this area.

This article uses strategy metaphors consisting of a plan, a home and a game to study government programme formation in Finland. The strategy approach both contradicts and complements the traditional political science approach to government formation. The government programme has been strategic in the sense of separating the formulation and implementation parts of the strategy. The most important function of the metaphor of plan is to hold coalition parties together. The adopted austerity policy provides a meagre contribution to the expansion of services and the increase in government spending. Consequently, the home metaphor in the government programme appears in the distant future and in combating external threats. The game metaphor is apparent in the goal of making contracts with social partners. The vocabulary change from politics to strategy alters the government programme’s position in terms of catering to the needs of civil servants, citizens and stakeholders. The strategy perspective might be instrumental in shifting open democratic debates to closed and secretive policy formations.

As the demand of heating and air conditioning is increasing day by day due to getting a comfortable life, for that reason, the market for heat pump and air conditioning systems or both, is seeing a steady increase in low global warming potential. All researchers on heat pump and air conditioning systems are searching for environmentally friendly refrigerants. However, a significant number of contemporary refrigerants (HCFCs) have the potential to cause global warming and ozone depletion, such as those found in heat pump air conditioning systems. Using more environmentally friendly refrigerants, including hydrocarbon and blend refrigerant mixtures, is one way to lower GWP and Ozone depletion potential. This study examines the performance of several alternative refrigerants, including R32, R134A, R410A, R22, and R290. In order to examine the performance of R290, theoretical and simulation results are compared on various refrigerants while taking into account a number of performance parameters, including the refrigerant energy efficiency ratio, mass flow rate, coefficient of performance, cooling capacity, and compressor work for one ton of refrigeration (1TR) air conditioners. One player with a very low GWP is R290. However, the only drawback is that it can catch fire and is hazardous to use in split-type commercial heat pump air conditioning applications. The environmental and thermo physical properties of HC-290 are significantly better than those of other materials, according to theoretical and simulation studies utilizing Cool Pack software, hence it is a viable replacement.

Civic participation is of great significance to urban management decision-making. In order to facilitate citizens to participate in city management decision-making, this paper proposes a large-scale group decision-making (LSGDM) method based on multi-granular probabilistic linguistic preference relations (MG-PLPRs). First, each decision maker selects a language terms set from the multi-granularity language terms set to represent individual preference relations and the MG-PLPRs are obtained by statistical calculation to represent sub-group’s preferences information. Then, an optimization model based on the expected consistency of PLPR and consensus measure of groups is established to achieving consensus reaching processes, which can ensure satisfactory individual consistency and group consensus. Finally, the validity and applicability of the proposed method is verified by a case of a city "shared garden" site selection with the participation of citizens.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

This study investigates cloud cavitation suppression around a model scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift-drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor-liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift-drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems.

The International Renewable Energy Agency (IRENA) was established in 2009 and in 2024, its membership increased to 168 members plus the European Union countries. The purpose of IRENA is to promote the adoption of renewable energy across all industries in the world. Despite the utilization of renewable energy in sectors like power generation and construction, its application in other industries remains limited. Therefore, a literature review study was conducted to investigate the cost and other spatial constraints associated with renewable energy resources, including modeling and optimization techniques that could offer viable solutions to the future challenges faced by the renewable energy production systems. This paper has summarized the result of this study with a focus on the significance of modeling and optimization techniques in energy conservation to highlight the untapped potential for leveraging renewable energy resources in industrial applications. This paper also examined a few case studies from various regions of the world, demonstrating the promising opportunities for research in the modeling and optimization of renewable energy management systems.

The integration of renewable energy and hybrid energy storage system (HESS) into electrified railways to build electric railway smart microgrid system (ERSMS) is beneficial for reducing fossil fuel consumption and minimizing energy waste. However, the fluctuations of renewable energy generation and traction load challenge the energy management effectiveness for such a complex system. In this work, an energy management strategy is proposed which firstly decomposes the renewable energy into low-frequency and high-frequency components by an integrated empirical mode decomposition (IEMD). Then, a two-stage energy distribution approach is utilized to appropriately distribute the energy flow among the ERSMS. Finally, the feasibility and effectiveness of the proposed solution are validated through case study.

Mixed plastic packaging waste sorting residues (MPO323) were treated by thermal pyrolysis to utilize pyrolysis oil and char. The pyrolysis oil was found to contain aromatic and aliphatic hydrocarbons. Chlorine and bromine contents were up to 40,000 mg/kg and 200 mg/kg, respectively. Additionally, other elements like sulfur, phosphorous, iron, aluminum, and lead were detected, which can be interpreted as impurities regarding the utilization of the oils by means of chemical recycling. The pyrolysis char showed high contents of potentially active species like silicon, calcium, aluminum, iron, and others. To enhance the content of aromatic hydrocarbons and to reduce the level of contaminants, the pyrolysis oil was reformed with the corresponding pyrolysis char to act as an active material in a fixed bed. The temperature of the reactor and the flow rate of the pyrolysis oil feed were varied to gain insights on cracking and reforming reactions as well as on the performance with regard to decontamination.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

The decarbonization of the electricity grid as one among the actions to reduce fossil fuel emissions, and thus their impact on global warming in the future, will be achieved mainly via the integration and widespread diffusion of renewable power sources. This is going to be supported also by the shift from the paradigm production-transmission-distribution, where electricity production oversees large-size power plants, to renewable-based distributed/diffused production, where electricity is generated very close or even by the same (group of) user(s) (or prosumers in the latter case). The number of mid-/small-size installations based on renewable energy technologies will therefore increase substantially, and the related renewable generation will be dominant against that from large-size power plants. Unfortunately, this will reduce the reliability of the grid very likely, unless appropriate countermeasures are taken/implemented, hopefully at the same time the paradigm shift is being achieved. To this aim, it is important to identify the anomalies and main fault causes that might determine in renewable-based power systems. This paper surveys the current state-of-the-art on anomalies and faults affecting wind-PV-storage hybrid power systems, i.e., the main renewable technology ensemble that will establish the future grid, and highlights possible research directions that may help to fill the literature gaps.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

This study aims to analyse the technical viability and economic feasibility of rainwater harvesting systems for single and multifamily residential buildings in the city of Florianópolis, Brazil. Simulations were conducted for representative buildings in the city under different water usage scenarios and system designs, in a total of 36 simulation scenarios. An economic analysis was performed for four scenarios over a twenty-year period. Both initial and operational costs were considered and net present value, internal rate of return and payback used as feasibility indicators. Almost all of the cases simulated were technically viable for the group of houses, and up to 78.9% for flats. As for the economic analysis, for houses, between 60.1% and 74.8% of the cases were economically feasible, achieving a discounted payback period ranging from 6.2 to 8.6 years. For flats, between 57.8% and 64.2% of the cases were economically feasible, achieving a discounted payback period ranging from 4.8 to 5.6 years. As the water tariff in the city underwent changes recently, the former and current tariff formats were compared. The current tariff format provides more economic benefits for saving potable water, and leads to a higher net present value and a shorter discounted payback period.

The cooling of server components has been continuously developed over the past few years in order to meet the increasing cooling requirements of server component manufacturers such as for the processor chips. The growth in performance and power density increases the cooling demand. These requirements directly influence the energy consumption and performance of the hardware. To gain a better understanding of the historical evolution and possible future technology development paths in the field of data center cooling, a patent analysis method was used. The focus is on previous and current development priorities and possible research gaps within the server and computer room levels. The European patent database was selected as data source. To determine relevant patents, the search terms for various cooling technologies were developed iteratively. After the patent extraction for the period 2000 - 2023 (earliest priority year), the search results were classified and analysed. Most of the patents deal with air or liquid cooling. In the area of liquid cooling, the focus was on direct liquid cooling, followed by total liquid cooling. Since 2015 a technological shift from air to liquid cooling can be identified on the level of patent activities. In this context, the patent groups with focus on “constructional details for different types of electric apparatus” and “electrical digital data processing” have the largest share of patents. In addition, the technology focus of the TOP 10 patent applicants was in the field of liquid cooling. In conclusion from the patent analysis, it can be derived that liquid cooling will continue to gain in importance in the future and could also be combined with other approaches in the form of hybrid cooling. However air cooling may still be relevant, even if the main cooling load is handled by liquid-based approaches. At the same time, the optimisation potential for air cooling seems to have been largely exploited in comparison to liquid cooling, as can be seen from the falling number of the patent applications.

A low cost, scalable and robust process has been proposed as innovative method for coating solar mirrors with a self-cleaning, transparent in the full solar range and versatile material based on auxetic aluminium nitrides, previously obtained on the laboratory scale. This work presents the scaling-up of fabrication process from laboratory to prototypal scale and pre-liminary results of outdoor self-cleaning solar mirror prototypes testing in the demonstrative CSP plant ENEASHIP located in Casaccia (Rome) ENEA research centre. Prototypes 50x40cm have shown stability in external conditions: no degradation occurs during the test campaign. Their washing restores the initial reflectance affected by soiling and the self-cleaning performance allows the utilization of a reduced quantity of water for cleaning operations with respect to uncoated glass of back surface mirrors. A similar self-cleaning AlN coating could be utilized on other solar components affected by soiling, such as glass envelopes of heat collecting elements, PV panels and everywhere are required self-cleaning performance combined to optical ones.

This article proposes a particular strategy to proceed with a progressive electrification of public transport systems in cities. Starting from a bus operation model, the possible electrification of two routes is analysed, one urban and another extra-urban in the city of Pisa. An estimate is made of the energy uses associated with certain operating modes. The maximum level of consumption is estimated at approximately 280 kWh per day per bus for the urban route and excluding some special days, less than 215 kWh per day for the extra-urban route, for which a hybrid bus is proposed. Starting from an estimate of the daily consumption for the management of the two routes, the sizing of a photovoltaic system distributed on some modular shelters which serves to power the same routes is carried out. The resulting system has a power of the order of 190-200 kW. The modular solution is also outlined, and an installation is proposed. The analyzed case lends itself to being easily replicated.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Market crises pose significant challenges for businesses, emphasizing the importance of effective crisis management strategies. Central to these strategies is the ability to identify and retain loyal customers, who often serve as the bedrock of stability during tumultuous times. This paper investigates the application of deep meta-learning analysis to predict loyal customers as a cornerstone of market crisis management. Drawing upon an extensive literature review, the study explores previous research on market crises, customer loyalty, and the evolution of deep learning and meta-learning in crisis management contexts. Methodologically, the paper outlines data collection, model development, and evaluation procedures tailored for deep meta-learning-based customer prediction. In results, the overall accuracy of model 85%, a precision 0.88, recall 0.82, and F1-score 0.85 were obtained. The analysis demonstrates the effectiveness of deep meta-learning models in accurately identifying loyal customers during market crises, offering insights into their performance and applicability compared to traditional methods. Practical implications include potential applications in crisis management for businesses and considerations for real-world implementation.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

In numerical simulations, achieving high accuracy without significantly increasing computational costs is often challenging. To address this, this paper presents an improved finite volume weighted essentially non-oscillatory (WENO) scheme tailored for applicability in computational fluid dynamics (CFD) and implemented in the flow solver NUAA-Turbo for simulating turbomachinery flows using both RANS and RANS/LES coupling. Firstly, the new WENO scheme is validated against classic numerical test cases to assess its stability and reliability in handling discontinuities, the Double problem, and Raleigh-Taylor (RT) instability issues. Compared to the original format, this enhanced finite volume WENO scheme demonstrates superior stability near discontinuities and resolves flow features with the same grid resolution more effectively. Next, for engineering applications related to turbomachinery, such as compressor and turbine characteristics, computations are performed using RANS, and the results obtained using WENO-ZQ3 and WENO-JS3 are compared. Finally, the new fifth-order WENO scheme is applied to RANS/LES coupled simulations of turbine wakes and film cooling. The results show that the enhanced finite volume WENO scheme offers improved stability and accuracy in engineering applications, allowing for high-precision calculations with fewer grid points to capture more detailed flow physics, thereby reducing computational costs in aerodynamic applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

This research investigates the challenges and opportunities associated with supply chain transparency and traceability in the renewable energy sector. Using a qualitative methodology, the study involved semi-structured interviews with key stakeholders, including industry experts, supply chain managers, regulatory officials, and NGO representatives. The findings reveal that the complexity and global span of renewable energy supply chains pose significant hurdles for ensuring transparency and traceability. Variability in the maturity of traceability systems across companies further complicates the landscape, with some companies benefiting from advanced systems while others struggle with cost and technical barriers. Technological advancements, especially blockchain, offer promising solutions but require standardization and scalability to be effective. Regulatory frameworks play a crucial role, yet inconsistencies across jurisdictions create compliance challenges, underscoring the need for harmonized standards. Collaboration and partnerships are essential, providing platforms for sharing best practices and developing common standards. Enhanced transparency can lead to operational efficiencies, improved consumer trust, and stronger market positioning. Integrating sustainability into supply chain practices is fundamental, aligning with the increasing emphasis on ESG criteria among investors and stakeholders. Education and capacity-building, particularly for suppliers in developing countries, are vital for promoting transparency. Leadership and corporate culture are critical in driving these efforts, with strong commitment from the top necessary to implement effective practices. This study contributes valuable insights for stakeholders in the renewable energy sector, offering a foundation for future research and policy development aimed at advancing sustainable and ethical supply chain practices. The findings highlight the need for a holistic approach that integrates transparency and traceability into broader sustainability and business strategies.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

This study uses the Scopus and Web of Science databases to review the forecast of electricity consumption from 2015 to 2024. Based on the keywords used in the article title, which are associated with electricity consumption forecasts, the study retrieved 821 docu-ments for additional analysis using various techniques. For frequency analysis, we used Mi-crosoft Excel; for data visualisation, we used VOSviewer; and for citation metrics and analysis, we used Harzing's Publish or Perish. Standard bibliometric variables, including publication growth, authorship patterns, collaboration, prolific authors, national contribution, most active institutions, favourite journals, and highly cited articles, are used in this study's reporting of the findings. Our analysis indicates that over ten years, starting in 2015, publications on the forecasting of electricity consumption have continued to increase. China was the country that contributed the most to research on electricity consumption. Most of the research publications on electricity consumption were published in the Journal of Energy.

Electronic waste generation has been following a continuously rising trend. With electronics containing a myriad of materials some of which are hazardous, toxic, extremely rare or precious combined with more stringent legislative laws which encourage the reuse and optimised recycling of the materials included in e-waste, the need for a holistic approach is inevitable. Such an approach should not only identify the materials found in the various types of e-waste and their respective quantities but also needs to highlight the possible handling techniques and their respective impacts and associated hazards whether to the environment or human health. Performing such a task manually would be exasperating and costly while requiring extensive resources which might not be met with a justifiable economic gain; thus, the use of the advancement in computational sustainability to draw a complete picture and aid in an informed decision-making process is crucial. The e-waste ontology developed in this paper is one way of addressing the problem since it covers the treatment domain, the hazard and the materials contained within the different types of e-waste. The ontology developed can be used directly from the protégé software or by embedding it into a developed Decision Support System.

EIMIs face the challenge of adapting to the Paris Agreement and the European Green Deal to achieve carbon neutrality. This change is being driven by consumer interest in low-carbon products, regulatory requirements from climate agreements and investors prioritizing sustainability. This pressure is pushing companies to go beyond short-term financial gains and integrate sustainability into their business. The growing awareness of the environmental impact of business models (BM) has fueled the development of Sustainable Business Models (SBMs). This study aims to link the discussion on the role of SBMs in the drivers of decarbonization, to improve the understanding of how the drivers can be integrated and enable new BMs for EIMIs. Based on a structured literature review, semi-structured interviews were conducted in the EIMIs. The study identifies BM-components that are influenced by these drivers and require sustainable business model innovation (SBMI). The results show that decarbonization drivers have a significant impact on all BM components. Experts emphasize the importance of collaborative approaches and cooperation throughout the value chain. This research elaborates on the importance of systematic analysis to understand how companies can effectively manage decarbonization drivers and suggests in-depth exploration within BM-research to uncover potential SBM design options.

Sustainability of current energy policies and known mid-term policies are analised in their multiple facets. First an overview is given about the trend of global energy demand and energy production, analysing the share of energy sources and the geographic distribution of demand, on the basis of statistics and projections published by major agencies. The issue of sustainability of the energy cycle is finally addressed, with specific reference to systems with high share of renewable energy and storage capability, highlighting some promising energy sources and storage approaches.

In modern warfare, the diversified tasks can sometimes be challenging to fulfill with a single projectile, necessitating the incorporation of cooperation constraints in trajectory planning. Limited by the stringent requirements of the launch platform and lower costs, the maneuverability and ability to adjust the flight time range of projectiles are weak. Therefore, the rationality of performance indicators and flight time coordination strategies is especially critical. To fully exploit the control capabilities of projectiles, a battlefield area segmentation method is proposed, differentiated performance indicators and a cooperative trajectory planning model that considers the entire range of projectiles are established. Considering the limitations of existing flight time coordination strategies in applications, targeted improvements have been made in different cooperation scenarios, and a bi-level adaptive cooperation strategy(BACS) with both optimality and flexibility is proposed. To rapidly determine feasible conditions, a simple and universal method for obtaining the capability ranges of cooperation is introduced. The multi-phase optimal control problems are transformed into nonlinear programming problems using the Radau pseudo-spectral method, and simulation results show that the proposed methods are capable of handling trajectory planning tasks in different cooperation scenarios. The improved strategies effectively enhance the planning success rate under relatively harsh conditions and BACS demonstrates good compatibility with the problems studied.

Due to constraints in launch platform and cost, the maneuverability of gliding-guided projectiles is limited, necessitating a rational design of their trajectory schemes. To reduce the sensitivity of trajectory schemes to uncertainties while ensuring compatibility between flight schemes and guidance control systems, and fully exploiting the control capability of the projectile, a closed-loop robust trajectory planning method is proposed. Models of major uncertain factors and states deviation at the control-start point are established. Based on the NIPCE method, the stochastic dynamic model is transformed into a high-dimensional deterministic model with PCE coefficients as state variables, and the uncertainty propagation law is obtained. A PID algorithm is employed to design a tracking guidance law based on position error feedback, and open-loop and closed-loop robust trajectory planning models are established accordingly. The optimal control problem is solved by transforming it into a nonlinear programming problem using the direct shooting method. Simulation results indicate that the NIPCE method can significantly improve the computational efficiency of uncertainty propagation while ensuring accuracy. Open-loop robust planning can effectively mitigate the sensitivity of gliding trajectories to uncertainties but cannot completely eliminate terminal dispersion. Closed-loop robust planning effectively improves control effort consumption on the basis of open-loop planning.

Deploying Cellular Internet of Things (CIoT) devices in urban and remote areas faces significant energy efficiency challenges. This is especially true for Narrowband IoT (NB-IoT) devices, which are expected to function on a single charge for up to 10 years while transmitting small amounts of data daily. The 3rd Generation Partnership Project (3GPP) has introduced energy-saving mechanisms in Releases 13 to 16, including Early Data Transmission (EDT) and Preconfigured Uplink Resources (PUR). These mechanisms extend battery life and reduce latency by enabling data transmission without an active Radio Resource Control (RRC) connection or Random Access Procedure (RAP). This paper examines these mechanisms using the LENA-NB simulator in the ns-3 environment, which is a comprehensive framework for studying various aspects of NB-IoT. The LENA-NB has been extended with PUR, and our analysis shows that PUR significantly enhances battery life and latency efficiency, particularly in high-density environments. Compared to the default RAP method, PUR reduces energy consumption by more than 2.5 times and increases battery life by 1.6 times. Additionally, PUR achieves latency reductions of 2.5-3.5 times. The improvements with PUR are most notable for packets up to 125 bytes. Our findings highlight PUR’s potential to enable more efficient and effective CIoT deployments across various scenarios. This study represents a detailed analysis of latency and energy consumption in a simulated environment, advancing the understanding of PUR’s benefits.

There are various types of charged particles in the space environment, which can cause different types of radiation damage to materials and devices, leading to on-orbit failures and even accidents of spacecraft. Developing lightweight and efficient radiation shielding materials is an effective approach to improve the inherent protection of spacecraft. The protective performance of different materials against proton and electron spectra in the Earth’s radiation belts is evaluated by Geant4 simulation. Based on the simulation results, suitable hardening components are selected to design composite materials, and B4C/PEEK composites with different B4C content were successfully prepared. Experimental results demonstrate that the simulated and experimental results for the electron, proton and neutron shielding performance of B4C/PEEK composites are consistent. These composites exhibit excellent radiation shielding capabilities against electrons, protons and neutrons, and the radiation protection performance improves with increasing B4C content in the B4C/PEEK composite materials.

This study explores the role of stakeholder engagement in enhancing supply chain sustainability within the renewable energy sector. Through a qualitative research approach, including in-depth interviews with key stakeholders such as government agencies, industry associations, renewable energy companies, community groups, and environmental organizations, the research reveals the complexity and significance of effective stakeholder engagement. Stakeholders highlighted diverse motivations, including environmental, social, economic, and regulatory concerns, driving their participation. The study underscores the importance of tailored engagement strategies that recognize stakeholder heterogeneity and address specific needs and expectations. Collaborative approaches, such as public-private partnerships and multi-stakeholder initiatives, were identified as crucial for pooling resources, sharing knowledge, and addressing common challenges. However, challenges related to power imbalances, conflicting interests, and communication barriers were also noted. Government policies and regulatory frameworks were found to play a pivotal role in shaping stakeholder engagement practices and sustainability outcomes. Regulatory uncertainty and inconsistency were cited as significant concerns that could undermine sustainability initiatives. Community engagement emerged as a critical factor, with local communities often directly impacted by renewable energy projects. Meaningful engagement, including consultation and benefit-sharing mechanisms, is essential for building trust and securing social acceptance. Emotional intelligence and marketing strategies were recognized as important tools for effective stakeholder engagement, emphasizing the role of empathy, active listening, and clear communication. The findings of this study highlight the need for a holistic and integrated approach to stakeholder engagement and supply chain sustainability in the renewable energy sector. By addressing diverse stakeholder needs, fostering collaboration, and aligning policies with sustainability goals, stakeholders can work together to accelerate the transition towards a more sustainable energy future.

This pioneering study explores the geospatial and temporal patterns of natural and human-induced disasters from 1900 to 2024, providing essential insights into their global distribution and impacts. Utilizing the comprehensive international EM-DAT database, our analysis reveals significant trends and disparities in disaster occurrences and their widespread consequences. Results showed a dramatic escalation in both natural and man-made (technological) disasters over the decades, with notable surges in the 1991-2000 and 2001-2010 periods. A total of 25,836 disasters were recorded worldwide, of which 69.41% were natural disasters (16,567) and 30.59% were man-made (technological) disasters (9,269). The most significant increase in natural disasters occurred from 1961-1970, while man-made (technological) disasters surged substantially from 1981-1990. Seasonal trends reveal that floods peak in January and July, while storms are most frequent in June and October. Droughts and floods are the most devastating in terms of human lives, while storms and earthquakes cause the highest economic losses. The most substantial economic losses were reported during the 2001-2010 period, driven by catastrophic natural disasters in Asia and North America. Our research highlights Asia as the most disaster-prone continent, accounting for 41.75% of global events, with natural disasters making up 61.89% of these events. Oceania, despite experiencing fewer total disasters, shows a remarkable 91.51% of these as natural disasters. Africa is notable for its high incidence of man-made (technological) disasters, which constitute 43.79% of the continent's disaster events. Europe, representing 11.96% of total disasters, exhibits a balanced distribution but tends towards natural disasters at 64.54%. Examining specific countries, China, India, and the United States emerged as the most frequently affected by both natural and man-made (technological) disasters. The impact of these disasters has been immense, with economic losses reaching their highest during the decade of 2010-2020, largely due to natural disasters. The human toll has been equally significant, with Asia recording the most fatalities and Africa the most injuries. Particularly, the decade from 2001 to 2010 experienced the greatest economic losses, primarily driven by natural disasters in Asia and North America. These insights highlight the urgent need for tailored disaster risk management strategies that address the distinct challenges and impacts in various regions. By understanding historical disaster patterns, policymakers and stakeholders can better anticipate and manage future risks, ultimately safeguarding lives and economies.

This work presents an innovative application of optimal control theory to the strategic scheduling of battery storage in the day-ahead electricity market, with a focus on enhancing profitability while factoring in battery degradation. The study incorporates in the optimisation framework the cost of battery capacity degradation, the effects of capacity degradation and internal resistance degradation into dynamics. We employ a continuous-time representation of the dynamics, in contrast with many other studies that use a discrete-time approximation with rather coarse intervals. We adopt an equivalent circuit model coupled with empirical degradation parameters to simulate a battery cell’s behaviour and degradation mechanisms with good support from experimental data. Utilising direct collocation methods with mesh refinement allows for precise numerical solutions to the complex, nonlinear dynamics involved. Through a detailed case study of Belgium’s day-ahead electricity market, we determine the optimal charging and discharging schedules under varying objectives: maximizing net revenues, profits considering capacity degradation, and profits considering both capacity degradation and internal resistance increase due to degradation. The results demonstrate the viability of our approach and underscore the significance of integrating degradation costs into the market strategy for battery operators, alongside its effects on the battery’s dynamic behaviour. Our methodology extends previous work by offering a more comprehensive model that empirically captures the intricacies of battery degradation, including a fine and adaptive time domain representation, focusing on the day-ahead market, and utilising accurate direct methods for optimal control. The paper concludes with insights into the potential of optimal control applications in energy markets and suggestions for future research avenues.

The digital transformation in Industry 4.0 has revolutionized quality control paradigms, integrating advanced technologies such as augmented reality, deep learning, and computer vision systems into a new era called "Quality 4.0". This study systematically reviews how these technologies are shaping new practices in continuous quality supervision and improvement, adapting to increasingly automated and connected production environments. Through a comprehensive analysis of the literature, practical applications in various industrial sectors, from manufacturing and agriculture to the production of sweets and snacks, are highlighted. Additionally, the conceptual and detailed design of a quality control system using artificial intelligence tools is presented, focusing on the inspection of dimensions, color, weight, and labeling of MDF boxes. The proposed system demonstrates an effective integration of sensors, high-definition cameras, and deep learning algorithms, validated through tests with boxes of different sizes. The results suggest that the adoption of these technologies not only improves the accuracy and efficiency of inspections but is also essential to maintaining high-quality standards in a dynamic and competitive industrial environment.

The climate crisis necessitates a global shift to achieve a secure, sustainable, and affordable energy system toward a green energy transition reaching climate neutrality by 2050. Because of this, renewable energy sources have come to the forefront and the research interest in microgrids which rely on distributed generation and storage systems has exploded. Furthermore, many new markets for energy trading, ancillary services, and frequency reserve markets have provided attractive investment opportunities in exchange for balancing the supply and demand of electricity. Artificial intelligence can be utilized to locally optimize energy consumption, trade energy with the main grid, and participate in these markets. Reinforcement learning (RL) is one of the most promising approaches to achieve this goal because it enables an agent to learn optimal behavior in a microgrid by executing specific actions that maximize the long-term reward signal/function. The study focuses on testing two optimization algorithms: logic-based optimization and reinforcement learning. This paper proposes an optimization algorithm based on reinforcement learning in an industrial microgrid that is capable of trading energy with the main grid, providing significant cost savings. The RL-based approach is implemented in Python based on real data from the site and in combination with MATLAB-Simulink to validate its results. The application of the RL algorithm achieved an average monthly cost saving of 20% compared to logic-based optimization and 86% savings compared to not using any optimization. These findings contribute to digitalization and decarbonization of energy technology and support fundamental goals and policies of the European Green Deal.

Emergency Medical Response Systems (EMRS) play a vital role in delivering medical aid during disasters. In Serbia, these systems encounter several obstacles due to economic limitations, scarce resources, and ongoing healthcare reforms, all of which affect their performance. This study focuses on examining the risk factors and effectiveness of Serbia's EMRS, identifying systemic issues, and proposing enhancements to improve emergency preparedness for disasters. A survey was conducted across healthcare institutions in Serbia to gather comprehensive insights. The survey explored various aspects, including organizational structures, resource distribution, communication systems, and the speed of emergency responses. Statistical methods such as Pearson's correlation, multivariate regression analysis and chi-square tests were utilized to interpret data collected from 172 healthcare institutions. The multivariate regression analysis of EMS organization identified that factors such as the structuring of working hours and shift patterns are significant predictors, contributing to small but meaningful variations in various EMS outcomes. In contrast, other factors, such as financial resources and the availability of ambulance vehicles, showed more targeted significance depending on the specific EMS aspect being analyzed. Institutions with written mass casualty plans and procedures demonstrate superior effectiveness in EMS activities, excelling in resource allocation, operational continuity, and emergency preparedness, particularly through enhanced coordination and specialized systems for managing large-scale emergencies. The findings highlighted notable disparities in how EMRS are organized, with only 46% of institutions having specific emergency departments. Resource limitations were evident, as many facilities operated with minimal staff and outdated equipment. The communication systems revealed weaknesses, with just 54% having established protocols for handling emergency calls. Response times frequently surpassed international standards, which negatively affected patient outcomes. Additionally, the study found training deficiencies, with 68% of participants expressing a need for further education. Serbia’s EMRS are significantly impacted by systemic issues such as insufficient funding, disjointed service delivery, and inadequate training. Overcoming these challenges necessitates a comprehensive approach that includes boosting financial support, implementing standardized protocols, and fostering enhanced collaboration across different sectors.

The paper deals with the design of a systematic procedure for implementing strategy changes into internal business processes for a project-oriented production type of organization. In the first part of the contribution, a summary of the theoretical starting points for the field of strategic management and change management is presented. In the second part, the contribution deals with the analysis of the current situation in the area of the impact of the change of strategy on the management of business processes. In the last part, the proposal of the procedure for implementing strategy changes into internal business processes and the verification results are presented. The proposed procedure includes steps where the selection and verification of key performance indicators at individual levels of management plus the quantification of the impact of the change in strategy on the processes takes place. The management can thus monitor and evaluate the chosen processes in accordance with the fulfilment of the chosen strategy of the company. The last chapter presents the verification of the proposal for the systematic introduction of changes into the processes.

Photovoltaic modules should pass series of tests and examinations, verifying the electrical and thermal characteristics of the module, before being released to the market, examining the properties of the modules should undergo appropriate durability and efficiency tests under real outdoor conditions with exposure to climatic conditions and under laboratory conditions. The performance of photovoltaic cells depends on many factors, such as solar irradiance, module operating temperature, installation location, weather conditions and module shading. In this paper, three selected photovoltaic modules were examined using a large-scale steady-state solar simulator. The current-voltage (I-V) characteristics of the photovoltaic modules were experimentally tested and analyzed. The next step was to implement a three-layer artificial neural network model (MLP). The experimental data obtained in the previous step coupled with output data from MLP were then used in global sensitivity analysis (GSA). Experiments carried out on a large-scale stationary solar simulator showed differences between the values declared by the manufacturer and the values obtained from measurements of PV modules. The first module tested achieved the maximum power point greater than that specified by the manufacturer, while the other two showed power drops; it was 85-87% for the second module, and 95-98% for the third, respectively. The performed global sensitivity analysis (GSA) for the MLP model showed that the parameters: eff (22.9) and Voc/V (14.19) have the largest effect on the power-voltage relationship, while U (7.29) has the smallest effect. The usefulness of machine learning (ML) methods in the comparative analysis of PV modules has been proved.

This paper performs a comprehensive analysis of the wind energy potential of onshore regions in Greece with emphasis on quantifying the volume risk and the spatial covariance structure. Optimization techniques are employed to derive efficient wind capacity allocation plans (also known as generation portfolios) incorporating different yield aspirations. The generation profile of minimum variance and other optimal portfolios along the efficient frontier are subject to rigorous evaluation using a fusion of descriptive and statistical methods. In particular, principal component analysis is employed to estimate factor models and investigate the spatiotemporal properties of wind power generation, providing valuable insights into the persistence of volume risk. The overarching goal of the study is to employ a set of statistical and mathematical programming tools guiding investors, aggregators and policy makers in their selection of wind energy generating assets. The findings of this research challenge the effectiveness of current policies and industry practices, offering a new perspective on wind energy harvesting with a focus on the management of volume risk.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

In the proposed article, the issues of increasing the synchronizing ability of the system of coordinated rotation of asynchronous motors are considered. Based on the T-shaped equivalent circuit, electromechanical relationships were obtained with changes in the value of the total rotor resistance and the supply voltage of individual motors. An algorithm for calculating the torques, stator and rotor currents of the motors of the system has been compiled. Based on the calculations obtained, the mechanical characteristics of the system asynchronous motors are constructed for various values of total resistance, supply voltages and rotor positions. The obtained data and graphs confirm the adequacy of the theory obtained in an analytical way. Functional and structural diagrams in small scales have been compiled, which allow simulating transient operation modes of multi-motor asynchronous electric drives in the Matlab application package. Multi-motor asynchronous electric drives with adjustable supply voltages, as well as with preliminary synchronization and synchronous braking, have been developed. Compilation of a program for the stability of a nonlinear system of a multi-motor asynchronous electric drive (MAEDs) with a thyristor voltage converter (TVC) in Matlab. Also, the modes of soft start, load shedding and surge on the motor shaft are simulated, confirming the stability of the system.

The paper examines the evolution and crucial role of energy communities in the context of the transition to renewable energy sources. Such communities are presented as an innovative and resilient response to the challenges posed by climate change. Their importance emerges from their ability to decentralise energy production, increasing local security and reducing dependence on non-renewable energy sources and external suppliers. However, despite the obvious benefits, the contribution highlights several challenges, such as the need for significant upfront investment and the presence of regulatory barriers that may hinder the integration of these solutions into existing energy systems. A detailed bibliometric analysis is used, focusing on specific research areas and using tools to map the most relevant keywords and emerging trends. The results of the bibliometric analysis highlight how energy communities are emerging as key players in the sustainability landscape, capable of addressing and overcoming contemporary environmental challenges. The research reaffirms the transformative potential of energy communities in promoting a more sustainable and resilient future.

Biosecurity is a tool used to alleviate the introduction, emergence and spread of diseases caused by infectious agents. It comprises different health-management activities that need to be followed to reduce the passage and dissemination of infectious agents within and among farms, poultry flocks, and humans, as well as within a country, among countries, or the whole globe. In terms of public health measures, biosecurity applies to practices that will reduce contact between poultry and humans and thereby reduce zoonotic disease transmission. Two of the common biosecurity measures are bioexclusion and biocontainment which themselves are further categorized as segregation/isolation, movement control and hygiene/sanitation/disinfection. Isolation is about putting poultry under an exclusively isolated environment where it lives alone without any interference from any source external to the poultry or at least under reduced and controlled interference. Movement/traffic control and sanitation measures are practices to follow the isolation of poultry or preparatory phase as in the case of sanitation of poultry houses before introduction of poultry. These techniques have been effective in controlling poultry diseases like avian influenza, exotic Newcastle, Marek’s disease, and any other diseases. Depending upon the underlying situation either bioexclusion or biocontainment measure will be used to control these infectious diseases of poultry.

This study examines the differential impact of proactive and reactive job crafting behaviors on job well-being, drawing from the perspective of boundary theory. The increasing popularity of work connectivity behavior after-hours (WCBA) after work has attracted widespread attention from scholars on the relationship between WCBA and employee well-being. One view suggests that the impact of WCBA is negative, while another view suggests it is positive. Obviously, the impact of (WCBA) on well-being at work is still contradictory. To clarify the complexity of the impact of WCBA on well-being at work, based on boundary theory, we divided WCBA into proactive WCBA (PC) and reactive WCBA (RC), and examined the double-edged sword effect of WCBA on well-being at work, as well as the mediating mechanisms of job control and work-to-home conflict, and the moderated effects of boundary segmentation preferences. This study uses empirical sampling method to collect data from 125 employees for a period of five days for quantitative research. The results show that, first, PC has an inverted U-shaped effect on job control, and job control is negatively related to well-being at work. Thus the mediating effect of job control is significant. Second, RC has a negative impact on job control, and there is also a negative relationship between job control and well-being at work. Therefore, the mediating effect of job control is significant. Third, PC and RC are positively correlated with work-to-home conflict, and work-to-home conflict has a significant positive impact on well-being at work. Therefore, the mediating effect of work-family conflict is significant. Fourth, the study also found that integration preference moderates the relationship between work-to-home conflict and PC on well-being at work, that is, the mediating effect of work-to-home conflict is stronger for employees with low integration preference. This study enriches our understanding of WCBA, PC and RC from the perspective of proactive and passive employee behaviors. The study also provides a new interpretation of the impact of WCBA on well-being at work and offers valuable insights for the sustainable development in digital social transformation and the application of boundary theory and the theory of empowerment-subjugation in achieving the United Nations Sustainable Development Goals. In addition, the study deepens our understanding of the heterogeneous regulatory role played by work-family integration preferences in influencing well-being at work under different types of WCBA.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

Brazil has ideal conditions for the large-scale use of cabotage cargo transportation: a vast coastline with almost 7,400 km, approximately 70% of the population resident in a coastal range of up to 200 km from the coast and a strong concentration of activities economic along the coast. However, there is an absolute domain of road modal for the transportation of goods, and cabotage is underused. The purpose of the study was to raise the main barriers that negatively impact the performance of Brazilian cabotage. To this end, it was used to bibliographic and documentary research, based on studies already published in journals, doctoral theses, master's dissertations, congress annals, technical reports and research on government-related government agencies sites, navigation companies and entities related to cabotage. The main barriers that contribute to the low use of cabotage in Brazil were identified and analyzed, as well as possible alternatives of solution for sustainable development of this mode of transport. Such a study will certainly serve as subsidies for the definition of public policies aimed at better use of Brazilian cabotage, as well as to encourage navigation companies to invest more in the transport of goods by cabotage, in order to contribute to the reduction of trucks on highways Brazilian and for environmental preservation.

Earth’s climate cannot be ignored any longer. Policies are vital in order to mitigate the negative effects of climate change. The energy crisis created by the Russo-Ukrainian war and pandemic affected the EU and its member states. The focus is more than ever on its energy policies and independence. The EU revised the energy strategy in response to Russia’s blackmail, and it sped up all the processes for energetic independence from Russia. This benefited the climate change policies the most, as all the measures involved reducing energy consumption and increasing renewables, thus contributing to reducing greenhouse gas emissions. As a member state of the EU, Romania is committed to complying with EU regulations. With a high degree of energy independence compared with the other EU members, Romania plans to become a regional energy provider and modernize the energy infrastructure internally as a response to Russia’s unprovoked aggression. The measures that the EU and Romania implemented after the war started in 2022 have come to fruition, and the effects are becoming visible a year later. This study aims to study the energy strategy of Romania in correlation with the EU strategy in the turbulent period of pandemics and war between 2019 and 2023, with the latest available data.

At present, farmland abandonment（FA）is a severe phenomenon in China, imposing a serious restriction on agricultural production. In this context, it is of great significance to explore the logical relationship between high-standard farmland construction (HSFC) and FA to optimize land resource allocation and guarantee national food security. Based on 838 samples of farmers in the main rice production area of the Yangtze River Basin in China, this paper employs the Tobit model, the mediating effect model, and the moderated mediating effect model to analyze the impact of HSFC on FA at the micro level. The results show that (1) HSFC inhibits FA, and FA proportion decreases by 1.14% for every 1% increase in HSFC proportion, and the robustness test and endogeneity treatment also yield consistent conclusions. (2) Agricultural socialization services (ASS) play a positive mediating role in the influence path. HSFC promotes farmers' purchase of ASS, which in turn inhibits FA. (3) The agricultural labor transfer distance (ALTD) plays a positive moderating role in the relationship between HSFC and FA. The farther the distance, the more likely HSFC can promote farmers' purchase of ASS and inhibit FA. The results provide enlightenment on how to precisely implement HSFC policy, that is, to inhibit FA by improving the construction of high-standard farmland and the post-construction management as well as protection system. Moreover, this study helps guiding the development of ASS and optimizing the institutional environment for agricultural labor transfer, creating conditions for agricultural scale management.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Vertical-axis wind turbines (VAWTs) are receiving more and more attention as they involve simple design, cope better with turbulence and are insensitive to wind direction which has a huge impact on the cost since the yaw mechanism is not needed. However, VAWTs still suffer from low conversion efficiency. As a results tremendous efforts are exerted to improve its efficiency which mainly focus on two methods regardless of whether the study is a CFD simulation or a field test or lab test experiment. An active approach which involves the modification of the rotor itself such as the blade design, angle, trailing and leading edges, inner blades, chord thickness, contra-rotating rotor, etc. While the second approach involves passive techniques where the flow is directed to optimally face the downwind rotor by mounting a guiding vane such as a diffuser or other shapes at the upwind position of the rotor. Among all techniques undertaken, the CRWT rotor technique seems to be the most effective with an output even comparable to that of Horizontal Axis Wind Turbines (HAWT), while the Savonius rotor received more attention compared to other designs of VAWTs. Apart from technological issues, it was also suggested that geographical issues such as proper site siting of the wind turbine rotor at a particular location where a uniform flow could be guaranteed is of paramount importance to ensure an effective conversion capacity of wind turbines.

This qualitative research explores the influence of Corporate Social Responsibility (CSR) on supply chain sustainability within the renewable energy sector. Through a comprehensive review of existing literature, key themes and patterns are identified, shedding light on the complex dynamics and interrelationships inherent in CSR practices and their impact on supply chain sustainability. The findings highlight the critical role of CSR in driving environmental sustainability, social equity, economic viability, governance mechanisms, and technological innovation across renewable energy supply chains. Environmental sustainability emerges as a priority, with CSR initiatives focusing on reducing carbon emissions, promoting clean energy technologies, and adopting sustainable sourcing strategies. Social equity is emphasized through stakeholder consultation, transparent decision-making, and investments in community development. Economic viability is addressed through considerations of brand reputation, financial performance, and regulatory compliance. Governance mechanisms and regulatory frameworks play a crucial role in shaping CSR practices, with collaborative partnerships and policy advocacy driving industry-wide change. Technological innovation, particularly the integration of blockchain, IoT, and AI, enhances transparency, traceability, and accountability in supply chains. The study concludes by discussing theoretical implications, practical insights, limitations, and avenues for future research, highlighting the importance of CSR in promoting sustainable development in the renewable energy sector.

This study focuses on the impact of collaboration on reducing price inflation in renewable energy supply chains. The study utilises in-depth interviews and theme analysis to reveal the complex dynamics of collaboration among stakeholders and the resulting implications for addressing difficulties in the renewable energy sector. Trust is a key factor in successful collaboration, whereas legal frameworks and policy incentives are important in influencing collaborative activities. Collaborative procurement, cooperative research and development, strategic alliances, and collaborative supply chain management are recognised as crucial measures for decreasing expenses, promoting innovation, and improving resilience in renewable energy supply chains. Nevertheless, in order to achieve successful collaboration, it is necessary to overcome obstacles such as lack of trust, uncertainty in regulations, and competitive dynamics. Creating a cooperative environment that prioritises common objectives, openness, and reciprocal advantages is crucial for fully harnessing the potential of renewable energy supply chains in promoting sustainable energy transitions. The report provides practical insights and recommendations for policymakers, industry professionals, and academics who aim to encourage collaboration and reduce price inflation in renewable energy supply chains.

Under the new pattern of “double carbon” development, good ESG performance is the best way to promote the sustainable development of enterprises, and the ESG investment strategies are directly affected by the strategic vision of managers. Based on the upper echelons theory and stakeholder theory, this paper takes Chinese A-share listed companies from 2011 to 2022 as samples to empirically analyze the impact of managerial myopia on corporate ESG performance. The results show that managerial myopia significantly inhibits corporate ESG performance, mainly by inhibiting corporate green investment and green innovation sustainability. Furthermore, for state-owned enterprises (SOE), heavy polluting enterprises (HPE) and non-high-tech enterprises, the inhibitory effect of manager myopia on ESG performance is stronger. When the enterprise is in the growth stage, the above inhibition effect is more severe. For external governance, the greater the analyst attention and public environmental attention are, the more conducive they are to alleviating the restraining effect of managerial myopia on enterprise ESG performance. Therefore, effectively improving the time cognition level of managers and strengthening external supervision have become important measures for comprehensively optimizing the ESG performance.

The collaboration of multimodal transport documents is the foundation for conducting multimodal transport operations. Blockchain technology can effectively address trust issues and information sharing difficulties in current multimodal transport document collaboration. However, in current blockchain-based electronic document research, the bottleneck problem lies in the collaboration of multiparty in multimodal transport under the "one-bill coverage system". We design a blockchain platform architecture for multimodal transport, reshaping collaboration processes for different modes of transport based on the blockchain platform. It proposes a collaboration model for multimodal transport under the "one-bill coverage system" and performs model solving and case analysis. The obtained collaboration strategies are embedded into the platform's application layer. Finally, using Solidity language, it writes smart contracts related to multimodal transport under the "one-bill coverage system " and deploys and executes them on the Remix platform.

Productivity has been modest in construction due to many reasons, especially project-specific operations and fragmentation. The main aim of this research is to map the challenges towards industrialization in construction through a comparative study of the manufacturing industry. An inductive approach and a qualitative method are followed by applying semi-structured inter-views, and node-based thematic analysis. The key elements of industrialization in mature man-ufacturing companies are benchmarked. The findings indicate a specific order of steps for indus-trialization in construction. Data and information management with achieved systematization have been sources of productivity in manufacturing companies. However, the systematization starts from the offering, construction companies need to define their offering, that is the products, and define their respective data. Only accurate and good quality data on products enables the systematization of order delivery processes, which are the engine for a company’s success or failure. Continuous efficiency improvement is only possible with systematized processes and respective data related to the processes. The originality involves clarifying the industrialization of construction companies via products, respective data, and processes considering industrialized manufacturing companies.

Long COVID is a phenomenon in which individuals experience persistent symptoms after recovering from COVID-19. The symptoms are discovered to be unique for every individual and can affect multiple organs systems in the body. This study aims to identify effective natural remedies for long COVID by analyzing hub genes associated with the symptoms of the condition and evaluating the repurposed drugs catered and used for treating the symptoms of long COVID. The most common and prevalent symptoms of long COVID were identified; Fatigue, Shortness of Breath, Loss of Smell, Headache, Brain Fog, Chest Pain, Insomnia, Heart Palpitations, Dizziness, Joint Pain, Depression, Anxiety, Tinnitus, Loss of Appetite. Hub genes for each of the symptoms provided an insight on the key biological pathways of the symptom. Repurposed drugs identified, provided the template to identify the natural compounds with similar structure as a potential therapeutic drug. The natural compounds were retrieved using fingerprint search of the repurposed drugs from the NPASS Database. The findings of this study suggest several natural remedies for each symptom based on the molecular docking of the hub gene and natural compound using iGEMDOCK. The identified natural remedies may hold promise in treating long COVID, but further research is required to explore the efficacy and effectiveness of the proposed natural compounds. The results of the study pose important implications for the development of effective treatments for long COVID.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

Background/Objectives: This study aimed to identify various risk factors associated with breast cancer and explore different treatment strategies based on socio-economic, hormonal, and clinical perspectives.; Methods: We analyzed socio-economic, hormonal, genetic, and clinical variables using data from 356 questionnaires obtained from breast cancer patients at Hassan II Regional Hospital in Agadir, Morocco ; Results:The study reveals that the average age of breast cancer patients is 50 ± 10.72 years, with a mode of 47 years and an age range from 29 to 94 years. Notably, women aged 38 are most frequently diagnosed with triple-negative breast cancer. Significant socio-economic trends were observed among the participants, with the majority being housewives (91%) and nearly half residing in rural areas (48.60%). High rates of illiteracy (74.72%) and financial difficulties (54.2%) pose challenges in accessing healthcare services. Psychological distress is prevalent, with 40.7% experiencing anxiety and 30.1% experiencing sadness. The use of oral contraceptives varies, with implications for breast cancer risk. Additionally, statistics on menarche and menopause suggest hormonal influences on breast cancer development. Histological analysis indicates a predominance of grade II invasive ductal carcinoma and left breast localization. Metastases are present in nearly 38.20% of cases. Notably, surgery as the primary treatment effectively treats medium-sized tumors while limiting metastasis. Furthermore, a comparison of treatment strategies reveals a preference for letrozole among postmenopausal patients and tamoxifen among premenopausal patients; Conclusions:These findings highlight the complexity of breast cancer risk factors and therapeutic approaches, emphasizing the importance of personalized care and targeted interventions.

Ethical sourcing practices play a pivotal role in addressing price inflation within renewable energy supply chains. This qualitative research investigates the multifaceted impacts of ethical sourcing, drawing insights from interviews with key stakeholders in the renewable energy sector. The study reveals that ethical sourcing enhances supply chain transparency, traceability, and resilience by mitigating risks associated with unethical practices such as labor exploitation and environmental degradation. Fair trade initiatives contribute to economic stability and reduce price volatility by ensuring fair compensation for producers and workers, fostering long-term relationships, and reinvesting premiums into community development projects. Sustainable sourcing practices align with consumer preferences for eco-friendly products, reduce the demand for virgin resources, and promote regulatory compliance and incentives, thereby stabilizing costs and reducing environmental impact. Socially responsible companies that prioritize fair labor practices and community support experience fewer disruptions and benefit from a more stable and productive workforce. Entrepreneurship and emotional intelligence among leaders drive the adoption and successful implementation of ethical sourcing practices, enhancing brand reputation, consumer trust, and market competitiveness. Despite challenges, such as higher implementation costs and supplier resistance, the long-term benefits of ethical sourcing outweigh the initial costs and contribute to sustainable supply chains. Collaboration, consumer education, and effective regulation are essential for promoting ethical sourcing across the renewable energy sector.

The renewable energy sector plays a pivotal role in addressing climate change and achieving sustainable development goals. However, the sector faces challenges related to price inflation and supply chain disruptions, which can impede its growth and resilience. This qualitative research explores supply chain resilience strategies adopted by companies in the renewable energy sector to mitigate the impact of price inflation and disruptions. Through semi-structured interviews with key industry stakeholders, the study identifies several key themes. Supplier diversification emerges as a crucial strategy for mitigating risks associated with geopolitical tensions and trade restrictions. Inventory management plays a pivotal role in ensuring continuity in operations amidst supply chain disruptions, with a focus on optimizing inventory levels of critical components. The adoption of digital technologies offers significant potential for enhancing supply chain visibility, transparency, and responsiveness, although integration challenges remain. Collaboration and partnerships within the industry are essential for sharing resources, knowledge, and best practices, fostering innovation and collective problem-solving. Sustainable practices are integral to supply chain resilience, aligning with broader industry trends towards environmental stewardship and social responsibility. Overall, the findings highlight the multifaceted nature of supply chain resilience in the renewable energy sector and the interconnectedness of various strategies and practices. Moving forward, companies must adopt a proactive and adaptive approach to supply chain management, integrating these strategies and practices into their operations to navigate uncertainties and drive sustainable growth. This study contributes to the understanding of supply chain resilience in the renewable energy sector and provides valuable insights for industry stakeholders, policymakers, and researchers.

This qualitative research investigates the intricate relationship between market dynamics and supply chain sustainability in the renewable energy sector. Amidst the global energy transition, renewable energy has emerged as a crucial player in mitigating climate change and fostering sustainable development. However, ensuring the sustainability of renewable energy supply chains presents complex challenges shaped by various market forces. Through semi-structured interviews and thematic analysis, this study explores how policy frameworks, technological innovation, market competition, consumer preferences, and investor demands influence sustainability practices across the renewable energy supply chain. The findings highlight the critical role of supportive policy environments, technological advancements, and stakeholder collaboration in driving sustainability performance and mitigating risks within renewable energy supply chains. Furthermore, the study identifies challenges such as supply chain complexity, regulatory compliance, and stakeholder engagement, underscoring the need for collaborative efforts and multi-stakeholder partnerships. By addressing these challenges and leveraging opportunities, stakeholders can advance sustainability goals, mitigate climate change impacts, and foster a more resilient and equitable renewable energy sector. The research contributes to a deeper understanding of market dynamics and supply chain sustainability in the renewable energy sector, offering insights for policymakers, industry stakeholders, and sustainability practitioners to inform evidence-based decision-making and drive positive change.

As the world’s second-largest economy, China has undergone rapid industrialization and urbanization, leading to high energy consumption and significant carbon emissions. This development has exacerbated conflicts between human-land relations and environmental conservation, contributing to global warming and urban air pollution, both of which pose serious health risks. This study utilizes nighttime light (NTL) data from 2005 to 2019, combined with scaling techniques and statistical analysis, to estimate city-scale energy carbon emissions over a 15-year period. Our focus is on Northeast China, a traditional industrial region comprising 36 cities across three provinces, rich in natural resources but now facing severe aging challenges. We analyzed the spatial patterns of energy carbon emissions, while spatiotemporal evolution was assessed through spatial autocorrelation and dynamic changes. These dynamic changes were further evaluated using standard deviation ellipse (SDE) parameters and SLOPE values. Additionally, we examined the conflict between city-scale emissions and economic growth using the Tapio decoupling index. Our findings for the 36 cities over the 15-year period include: (1) Heilongjiang shows low emissions with a downward trend; Jilin shows overall improvement; Liaoning has high and steadily increasing emissions. (2) The global spatial autocorrelation of energy carbon emissions is significant, with a positive Moran’s I, while significant local Moran’s I clusters are concentrated in Heilongjiang and Liaoning. (3) The SDE shows the greatest changes in city-scale emissions occurred in 2015, followed by 2019, 2005, and 2010. (4) Emission growth across the 36 cities is fastest in Heilongjiang, followed by Liaoning and Jilin. (5) Tapio decoupling analysis shows overall positive decoupling in Heilongjiang, a decline in decoupling quality in Jilin, and no significant change in Liaoning. Finally, we recommend strategies to reduce emissions from the perspectives of government, industry, and residents. This research offers a quantitative foundation for achieving dual carbon goals and supports the implementation of policies focused on energy transition and sustainable urban planning.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Volcanic activity essentially consists of the transfer of heat from the Earth’ interior to the surface. The precise signature of this heat transfer relates directly to the processes underway at and within a particular volcano and this can be observed, at a safe distance, remotely, using infrared sensors that are present on Earth-orbiting satellites. For over 50 years, scientists have perfected this art using sensors intended for other purposes, and they are now in a position to determine the particular sort of activity that characterizes different volcanoes. This review will describe the theoretical basis of the discipline and then discuss the sensors available for the task and the history of their use. Challenges and opportunities for future development in the discipline are then discussed.

Dogs population increased exponentially in the past decade while the birth rate decreased gradually, especially in the developed countries. Due to dogs’ characteristics of loyalty and obedience, most pet owners treated their dogs as their family members or companions, therefore they are willing to select and purchase safe, high quality and nutrition dog food to their dogs. However, there is lack of regulation or standard to reinforce the production or distribution of dog food in Hong Kong. Consequently, this paper will first review the relationship between high dog population and declining birth rate, types of dog food and typical ingredients. Secondly, the potential health implications of various “toxic” food ingredients for dog, hazard analysis of dog food and its testing methods will be investigated. Lastly, this paper will summarize worldwide existing standards and regulations, quality and hygiene management system related to dog food safety to provide insights and suggestions to Hong Kong government about the importance and urgency of implementing regulations and policies to oversee the imported and local manufactured dog food.

This qualitative research investigates the effectiveness of certification programs in ensuring supply chain sustainability within the renewable energy sector. Through interviews and content analysis, the study explores stakeholder perceptions, challenges, and impacts of certification initiatives. Findings reveal diverse motivations driving certification adoption, including regulatory compliance, market differentiation, and corporate social responsibility. However, challenges such as greenwashing and limited transparency undermine the credibility and effectiveness of certification programs. Despite these challenges, certification initiatives drive incremental improvements in environmental performance and stakeholder engagement, fostering a culture of continuous improvement and innovation. Multi-stakeholder collaboration and context-specific approaches are essential to address regional disparities and promote sector-wide transformation. Strategies for improvement include strengthening monitoring and enforcement mechanisms, integrating emerging technologies, and aligning certification standards with broader sustainability goals. Overall, certification programs offer a pathway for promoting transparency, accountability, and responsible business practices within the renewable energy supply chain, contributing to the transition towards a more sustainable and resilient energy future.

Long COVID, also referred to as post-COVID-19 condition, describes the lingering after-effects of COVID-19 infection. This complex syndrome encompasses a range of symptoms affecting physical well-being, cognitive function, and mental health. The widespread impact of long COVID extends beyond individual sufferers, placing significant strain on healthcare systems and causing far-reaching socioeconomic consequences. The scale of this multifaceted health crisis is unparalleled in recent history, affecting millions globally and challenging our understanding of post-viral conditions. This study aimed to explore the possibility of targeting G protein-coupled receptors (GPCRs) signaling pathway-related genes as therapeutics for long COVID using computational analysis. Targeting GPCRs and their signaling pathways holds significant promise for long COVID therapeutics, as these receptors are involved in crucial physiological processes including immune regulation, inflammation control, and neurotransmission. All of these are implicated in the diverse and persistent symptoms of long COVID, potentially offering a versatile approach to addressing multiple aspects of the condition simultaneously. This study identified 21 genes associated with GPCRs for further exploration as potential targets. Notably, GPCR genes such as HRAS, KRAS, GNAQ, and GNA11 were determined to be possible therapeutic targets for the pathophysiological mechanisms of long COVID. FDA-approved drugs targeting these genes were identified, including Binimetinib, Cabozantinib, Selumetinib, Panitumumab, Cetuximab, Adagrasib, Tipifarnib, and Sotorasib. Additionally, Naltrexone and Tipifarnib have emerged as potential new treatment options for long COVID. SARS-CoV-2 may hijack GPCR signaling pathways to dysregulate lung ion and fluid transport, contributing to the pathophysiology of pulmonary edema in patients with COVID-19. Further research is required to translate the findings into the development of therapeutics and to investigate the relationship between viral infection and GPCR signalling.

This paper aims to assess whether the financial performance of Portuguese companies that publish sustainability reports (SR) differs from the financial performance of companies that do not publish SR. We use two methodological procedures. First, we conducted a univariate analysis to test the differences in the financial performance according to the disclosure of SR. Second, we conducted a multivariate analysis using a multiple linear regression that explains financial performance by the disclosure of SR, as well as control variables such as sector, size, leverage, growth, and liquidity. Findings indicate that financial performance of companies that disclose SR does not significantly differ from the financial performance of companies that do not disclose SR. The results are robust to both methodological procedures, as well as to the sample split by sectors.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

This paper proposes a methodology for the development and its Verification and Validation(V&V) of safety-rated software. The development methodology is based on the structured analysis and structured design methodology, which has been proven in the field of safety software development during long period. The suggested the development and the V&V methodology additionally focuses on the quality attributes 3C+T (completeness, Correctness, Consistency and traceability), which are important criteria in IEC international standards. The software development life cycle is compiled from IEC international standardization, which are of the requirements analysis phase, design phase, implementation phase, testing phase, installation/commissioning phase, and operation & maintenance phases. The activities of the development process method were defined from requirements analysis to implementation, and the activities of the verification and validation were defined to include the scope of the developer's activities and then to include the test phase, installation/commissioning phase, and operation phases additionally. In other words, testing phase performed by the developer was defined as informal testing, and testing performed by the verifier according to test criteria, test plans, and test procedures was defined as formal testing. According to proposed methodology, the requirements phase defines the sequence of Entity Relationship Diagram (ERD)-Context Diagram-Data Flow Diagram (DFD), functional decomposition process and defines operational scenario. In the design phase, module design such as task analysis and task allocation were defined. In the implementation phase, we listed the coding guidelines that must be followed for safety-related system. The test phase defined the test criteria, test plan, test procedure, and test result report activities. In the installation/commissioning and operation phases, recommendations for improving reliability, quality, and safety were proposed for deliverables such as user documentation and technical documentation.

This paper presents a comprehensive study on applying machine learning (ML) techniques for real-time credit card fraud detection. With the increasing prevalence of credit card fraud, financial institutions face the challenge of detecting fraudulent transactions promptly and accurately. This research evaluates various ML models, including Logistic Regression, Decision Trees, Random Forests, XGBoost, and Deep Convolutional Neural Networks, for their effectiveness in identifying fraudulent activities. Utilizing PySpark for processing large-scale transaction data, the study highlights the importance of real-time analysis, adaptive learning, and handling imbalanced datasets. Key findings reveal that XgBoost, with its balance of accuracy and complexity, emerged as the most promising model, achieving an accuracy rate of 98% in detecting fraudulent transactions. The paper further discusses the potential of ensemble methods, graph-powered systems, and intelligent sampling in enhancing fraud detection capabilities. Challenges such as overfitting, data access, and the need for real-time analysis are addressed. Future research directions include implementing models in live transaction environments, expanding model applicability across financial platforms, and developing advanced anomaly detection methodologies. This study underscores the pivotal role of machine learning in safeguarding financial transactions against fraud, offering significant implications for consumers, financial institutions, and the broader financial ecosystem.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

Food insecurity remains a significant developmental challenge, particularly in rural areas, despite ongoing efforts to mitigate it. To better understand the persistence of this issue, this study investigates the causes of household food insecurity and the coping strategies employed by households in Zorkor Goo, Zorkor Kanga, and Zorkor Kadaare communities within the Bongo District of Ghana’s Upper East Region. A descriptive cross-sectional survey was conducted, sampling 196 households systematically from these communities. Data were collected through a structured questionnaire covering socio-demographic factors, causes of food insecurity, household coping strategies, and dietary intake. The analysis was performed using SPSS (Version 21.0), with food security status and dietary intake assessed via the FANTA Household Food Insecurity Access Scale (HFIAS) and Food Consumption Score, respectively. The study identified key factors contributing to food insecurity, including soil infertility, poor rainfall patterns, food spoilage, extravagant funerals, large family size, high unemployment, and lack of education. Major coping strategies among households included meal skipping, reducing meal size and frequency, migration, asset sales, and basket weaving. The findings revealed that 96.4% of households were severely food insecure, and over two-thirds (67.3%) exhibited poor dietary consumption. Notably, household employment levels, education, and food consumption scores were significantly associated with food insecurity (P<0.001). These findings underscore the need for targeted interventions addressing the root causes of food insecurity and enhancing household resilience in these communities.

This research article investigates the application of artificial intelligence (AI) in human resource management (HRM) within the Australian commercial media sector, addressing a critical gap in scholarly knowledge. Despite increasing interest in AI’s potential, there is a lack of consensus among managers and HR professionals regarding its application. Through qualitative interviews with 22 industry professionals, this study examines perceptions, understanding, and the potential for leveraging AI across key HRM functions. Findings indicate significant potential for AI to enhance HRM processes, particularly in job/work design and staffing. This research contributes to a deeper understanding of AI’s role in HRM and offers insights to optimize organizational efficiency and effectiveness in the Australian commercial media sector.