The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

In today's human society, diesel generators (DGs) are highly applied into the human energy and electricity supply system due to its technical, operational and economic advantages. This paper proposes an intelligent nonlinear $H_2/H_{\infty}$ robust controller based on the chaos particle swarm gravity search optimization algorithm (CPSOGSA), which controls the speed and excitation of a DG. In this method, firstly, establish the nonlinear mathematical model of the DG and then design the nonlinear $H_2/H_{\infty}$ robust controller based on this. The direct feedback linearization and the $H_2/H_{\infty}$ robust control theory are combined and applied. Based on the design of the integrated controller for DG speed and excitation, the system's performance requirements are transformed into a standard robust $H_2/H_{\infty}$ control problem. The parameters of the proposed solution controller are optimized by using the proposed CPSOGSA. The introduction of CPSOGSA completes the design of an intelligent nonlinear $H_2/H_{\infty}$ robust controller for DG. The simulation is implemented in MATLAB/Simulink, and the results are compared with the PID control method. The obtained results prove that the proposed method can effectively improve the dynamic accuracy of the system and the ability to suppress disturbances and improve the stability of the system.

The severe climate changes due to global warming pushed the world to strive to reduce carbon emissions. This study aims to minimize the carbon emissions for a proposed smart energy hub. This paper prioritizes the minimization of carbon emissions, taking into consideration the minimization of operation running costs, and the maximization of profit. In this paper two optimization scenarios were studied, to compare the results. In the first scenario, the minimization of carbon emissions was achieved, in the second scenario, the minimization of running costs and maximization of profit from the hub assets were studied. The proposed model was designed in MATLAB. Then the results were verified by CPLEX and validated by RTDS. The multi-objective model was presented to obtain the optimal operation. The mitigation of data uncertainty was achieved by applying the Kalman filter. In this work, a novel method was proposed for the estimation of the quarter-hour resolution data from the hourly one via the Kalman filter rather than applying the classic polynomial interpolation methods.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Vibration problems have become one of the most important factors affecting robot performance. To this end, a terminal residual vibration suppression method based on joint trajectory optimization is proposed to improve the accuracy and stability of robot motion. Firstly, based on the characteristics of the friction nonlinearity due to joint coupling and physical feasibility of dynamic parameters, a semidefinite programming method is used to identify dynamic parameters with actual physical meaning, thereby obtaining an accurate dynamic model. Then, based on the result of the residual vibration time domain analysis, a joint trajectory optimization model with the goal of minimizing joint tracking error is established. The Chebyshev collocation method is used to discretize the optimization model. The dynamic model is used as the optimization constraint, and barycentric interpolation is used to obtain the optimized joint motion trajectory. Finally, industrial robot experiments prove that the vibration suppression method proposed in this article can reduce the maximum acceleration amplitude of residual vibration by 62% and the vibration duration by 71%. Compared with the input shaping method, the method proposed in this paper can reduce the terminal residual vibration more effectively and ensure the consistency of running time and trajectory.

This study explores fault-tolerant consensus in leader-following heterogeneous multi-agent systems, focusing on actuator failures in uncrewed aerial vehicles (UAVs) and uncrewed ground vehicles (UGVs). An optimization-based fault-tolerant consensus algorithm is proposed. The algorithm utilizes the Euler-Lagrange formula to ensure system consistency under actuator failures, with the Lyapunov stability theory proving the asymptotic stability of the consistency error. The algorithm is applied to heterogeneous multi-agent systems of UAVs and UGVs to derive optimal fault-tolerant consensus control laws for each vehicle type. Simulation experiments give evidence for the feasibility of the proposed control strategy.

The real systems are often complex, nonlinear, and noisy in various areas including mathematics, natural science, and social science. We present the symplectic entropy (SymEn) measure as well as an analysis method based on SymEn to estimate the nonlinearity of the complex system by analyzing the given time series. The SymEn estimation is a kind of entropy based on symplectic principal component analysis (SPCA) which represent organized but unpredictable behaviors of systems. The key to SPCA is to preserve the global submanifold geometrical properties of the systems through symplectic transform in the phase space, which is a kind of the measure-preserving transforms. The capability of preserving the global geometrical characteristics makes the SymEn a test statistic to detect the nonlinear characteristics in several typical chaotic time series and the stochastic characteristic in the Gaussian white noise. The results are in agreement with findings in the approximate entropy (ApEn), the sample entropy (SampEn) and the fuzzy entropy (FuzzyEn). Moreover, the SymEn method is also used to analyze the nonlinearities of the real signals (including the EEG signals for ASD and healthy subjects, and the sound and vibration signals for the mechanical systems). The results indicate that the SymEn estimation can be taken as a measure for describing the nonlinear characteristics in the data collected from the natural complex systems.

Taking a certain type of test centrifuge as the research object, the finite element model of the test centrifuge is established, the vibration characteristics and aerodynamic performance of the test centrifuge are analyzed, and the structural optimization design of the test centrifuge is carried out. In this paper, the load is applied according to the actual working condition of a certain type of test centrifuge. The vibration of the mounting seat of the test centrifuge is analyzed and the structure of the mounting seat is optimized. After optimization, the vibration of the mounting seat is 77.38 % lower than that of the original mounting seat. Then, the aerodynamic analysis of the test centrifuge is carried out. The analysis results show that the test centrifuge moves more smoothly under the whole package shell and the steady flow shell, and the resistance decreases and the shaft load decreases. Finally, the steady flow shell of the test centrifuge is optimized. The analysis shows that the increase of the width of the steady flow shell can reduce the resistance coefficient, which is helpful to the stability of the test centrifuge during operation and reduces the unbalanced response of the system caused by air resistance.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

Silicon carbide particle-reinforced aluminum matrix (SiCp/Al) composites are significant lightweight metal matrix composites extensively utilized in precision instruments and aerospace sectors. Nevertheless, the inclusion of rigid SiC particles exacerbates tool wear in mechanical machining, resulting in a decline in the quality of surface finish. This work undertakes a comprehensive investigation into the problem of tool wear in SiCp/Al composite materials throughout the machining process. Initially, a comprehensive investigation was conducted to analyze the effects of cutting velocity vc, feed per tooth fz, milling depth ap, and milling width ae on tool wear during high-speed milling under SCCO2-MQL (Supercritical Carbon Dioxide Minimum Quantity Lubrication) ultrasonic vibration conditions. Furthermore, a prediction model for tool wear was developed by employing the orthogonal test method and multiple linear regression. The model's relevance and accuracy were confirmed using F-tests and t-tests. Ultimately, through the utilization of a genetic algorithm, the milling parameters were optimized, resulting in the identification of the most optimal combination of parameters. Empirical findings suggest that the careful selection of milling parameters can significantly mitigate tool wear, extend the lifespan of the tool, and enhance the quality of the surface. This work serves as a significant point of reference for the processing of SiCp/Al composite materials.

The extensive utilization of drones has led to numerous scenarios that encompass both advantageous and perilous outcomes. By using deep learning techniques, it is aimed to reduce the dangerous effects of drone use through early detection of drones.The state of the art of the study is evaluation of deep learning approaches such as pre trained YOLOv8 drone detection for security issues. In this study, dataset collected by Mehdi Özel for a UAV competition are sourced from GitHub. These images are labeled using Roboflow, and the model is trained on Google Colab. To enhance model performance, dataset augmentation techniques including rotation and blurring are implemented. Following these steps, a significant precision value of 0.946, a notable recall value of 0.9605 and a considerable precision-recall curve value of 0.978 are achieved, surpassing many popular models such as Mask CNN, CNN, and YOLOv5.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

In this paper, the design and control of a hydraulic system based tire changer machine have been analyzed and simulated using Matlab/Simulink Toolbox successfully. The machine have a displacement input which is a leg pedal displacement in order to push the piston of the pump to fed the motor with a pressured hydraulic fluid to rotate the tire with an angular speed to mount and dismount it. Augmentation based H_∞ and H₂ optimal synthesis controllers have been used to improve the performance of the machine. Comparison of the proposed controllers for tracking a reference input speed have been done using two reference inputs (step and random) signals. Finally the comparative simulation results proved the effectiveness of the proposed tire changer with H synthesis controller in improving the settling time and percentage overshoot.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

This study presents a groundbreaking approach in the field of gaming AI, focusing on the classic game” Pacman” through the lens of DRL integrated with advanced optimization techniques. The core of the research involves adapting DRL models for” Pacman”, utilizing the ESO for hyper- parameter tuning. These novel adaptations significantly enhance the AI agent’s performance, demonstrating a remarkable improvement in adaptability, responsiveness, and efficiency within the game environment. A pivotal aspect of this research is the innovative integration of metaheuristic optimization techniques into the DRL framework, a first in the domain of Atari gaming AI. This integration has proven essential in fine-tuning the DRL models, leading to a more effective and dynamic gaming experience. The study thoroughly evaluates and compares the performance of these algorithms, providing empirical support for their effectiveness and setting a new benchmark in AI-driven game development. The implications of this research extend beyond gaming AI, opening up possibilities for future exploration in several directions. Expanding DRL models to other complex gaming environments, continuous algorithmic enhancements, real-time learning adaptations, and applying these principles to robotics and autonomous vehicles are examples. The research also emphasizes ethical and responsible AI use in gaming to address fairness and addiction issues.

Incorporating renewables in the power grid presents challenges for stability, reliability, and operational efficiency. Integrating Energy Storage Systems (ESS) offers a solution by managing unpredictable loads, enhancing reliability, and serving the grid. Hybrid storage solutions have gained attention for specific applications, suggesting higher performance in some respects. This paper compares the performance of hybrid energy storage systems (HESS) to single battery, evaluating their energy supply cost and environmental impact through optimization problems. The model generates an optimized dispatch, minimizing cost or environmental impact of supplying energy to a generic load while considering battery degradation. Seven technologies are assessed, with an example applied to an industrial site contrasting vanadium redox flow (VRFB) and lithium batteries considering the demand of a local load (building). The results also indicates that efficiency and degradation curves have the highest impact in the final costs and environmental functions on the various storage technologies assessed. For the simulations of the example case, a single system only outperforms the hybrid system in cases where lithium efficiency is higher than approximately 87% and vanadium is lower approximately 82%.

According to the requirement of 20kg load of casting barrel, we design a three-dimensional model of the robot and analyze the three stages of liquid level change in the casting barrel during the casting process. Through the analysis, it is determined that the time and angle function is an implicit function, and it is impossible to find the analytical expression of time about angle. The kinetic function of the casting barrel is simulated by MATLAB, and it is found that the function image has mutation points, and when the original function is fitted and approximated by fifth-degree polynomial interpolation, the fifth-degree polynomial function image of the time versus the angular acceleration has a large amplitude of oscillation, especially the mutation points. A PID algorithm based on the discretization of the time and acceleration function is introduced for correction, and the results show that this method effectively reduces the oscillation amplitude of the image and improves the coincidence with the original function.

The ever-growing concerns about global warming and the rapid depletion of fossil fuels have triggered a rising interest in research for cleaner, more efficient and cost-effective energy generation. Organic Rankine cycle systems have immense potential to become a strong alternative to conventional methods of energy generation. However, such systems’ efficiency is limited by the performance of the incorporated gas expanders or prime movers. Conventional gas expanders often utilize ports or cam-operated valves. Ported expanders offer limited efficiency and controllability, and produce high emissions causing a large amount of heated and compressed gas to be wasted. Cam-operated valves, in contrast, increase expansion performance compared to ported expanders, however, they have no variability and adaptability to changes in system parameters such as gas pressure, temperature, dryness fraction, and load variation to name a few. On a positive note, this issue can be addressed by adopting a variable timing and fast-operating, control valve with an accurate and adaptive control mechanism at the expander inlet. A properly designed and controlled valve can greatly improve the system performance of gas expanders and pave the way for an efficient low-cost alternative energy generation. This manuscript provides a comparative review of recent progress on the design, modeling, optimization, and control aspects of valves for gas expanders. A clear pathway on the scope of further development is also drawn based on the present state of the art.

Since large power transformers are custom-made, and their design process is a labor-intensive task, their design process is split into different parts. In tendering, the price calculation is based on the preliminary design of the transformer. Due to the complexity of this task, it belongs to the most general branch of discrete, non-linear mathematical optimization problems. Most of the published algorithms are using a copper filling factor based winding model to calculate the main dimensions of the transformer during this first, preliminary design step. Therefore, these cost optimization methods are not considering the detailed winding layout and the conductor dimensions. However, the knowledge of the exact conductor dimensions is essential to calculate the thermal behaviour of the windings and make a more accurate stray loss calculation. The paper presents a novel, evolutionary algorithm-based transformer optimization method which can determine the optimal conductor shape for the windings during this examined preliminary design stage. The accuracy of the presented FEM method was tested on an existing transformer design. Then the results of the proposed optimization method have been compared with a validated transformer design optimization algorithm.

Brushless Direct Current Motors are significantly improved for using many electrical applications. The design investigation is increased year by year and most of the motor design researchers find out the superior efficiency of the BLDC motor. The traditional motor consumed more electrical power than BLDC motor. The design of BLDC motors that are compact, small, easy to control, save energy and light weight. Due to this fact, the design of BLDC motor should be analyzed to improve the motor characteristics performance. The research focuses on the design of BLDC motor performance using Taguchi Method and Response Surface Methodology (RSM) for Finite Element Method (FEM). Firstly, the Taguchi Method is applied to identify the optimization point of design parameters and consider using the reference model of actual BLDC electric fan motor with a rated power of 26Watts design. Based on the Taguchi Method to create the RSM is used to two-step optimization design performance using in FEM analysis. The performances of motor design proposed approach to provide the effeteness for motor design investigator. In this investigation aims the better structural performances in output power, torque, efficiency and torque ripple. The final design of proposed model achieved an energy efficiency is 10% higher than the reference design of prototype modes, the output power result is 10W higher this reference design. We can reduce the loss of the proposed motor design. Furthermore, the maximum torque can also increase the 0.032Nm of that design. The design simulation results were produced and studied by the FEM analysis of JMAG software. From the evaluation results, the configurations of reference model design are compared with the proposed design by using the three methods of motor design optimization showed the best characteristics for performance of motor investigation design.

Global optimization is widely adopted nowadays in a variety of practical and scientific problems. In this context, a group of techniques that is widely used is that of evolutionary techniques. A relatively new evolutionary technique in this direction is that of Giant Armadillo Optimization, which is based on the hunting strategy of giant armadillos. In this paper, a number of modifications to this technique are proposed, such as the periodic application of a local minimization method as well as the use of modern termination techniques based on statistical observations. The proposed modifications have been tested on a wide - series test functions, available from the relevant literature and it was compared against other evolutionary methods.

Electric vehicles (EVs) are pivotal in addressing the escalating environmental crisis. While EV drivetrains excel compared to those of vehicles with internal combustion engines (ICE), their energy storage systems are hampered by limited range, lifespan, and lengthy charging times. Hybrid energy storage systems (HESS) present a viable current solution to these issues. This review thoroughly explores state-of-the-art in the emerging field of multisource EVs that utilize HESS, incorporating any combination of batteries (BTs), supercapacitors (SCs), flywheels (FWs), fuel cells (FCs), and/or transmotors. In addition, the paper systematically categorizes and evaluates different hybrid configurations, detailing potential topologies and their respective advantages and limitations. Moreover, the paper examines diverse control algorithms used to manage these complex systems, focusing on their effectiveness and operational efficiency. By identifying current research gaps and technological challenges, this study aims to delineate future research directions that could enhance the deployment and optimization of multisource EVs, thereby addressing critical challenges such as energy density, system reliability, and cost-effectiveness.

Cascading landslides represent a dynamic and hazardous geological phenomenon, char-15 acterized by a sequential chain of slope failures triggered by various factors such as heavy rainfall, 16 seismic activity, or anthropogenic activities. These events can amplify the damage caused by the 17 initial trigger and propagate instability along a slope, often resulting in significant environmental 18 and societal impacts. The Morino-Rendinara cascading landslide, situated in the Ernici mountains 19 along the border of Abruzzo and Lazio region (Italy), serves as a notable example of the complexities 20 and devastating consequences associated with such events. In March 2021, a substantial debris flow 21 event in Morino obstructed the Liri River, marking the latest step in a series of landslide events 22 characterized by a complexity far beyond initial expectations. This study employs a multidiscipli-23 nary approach, combining conventional techniques and advanced technologies, to understand the 24 complexities of the Morino-Rendinara landslide. Field activities, UAV image acquisition, SAR inter-25 ferometry based on SENTINEL-1 images and pixel offset analysis based on high-resolution Google 26 Earth images, offer insights into the geological and hydrogeological setting of the unstable slope, 27 landslide geometry, mechanism and kinematics. To supplement the analysis a specific FEM slope 28 stability analyses is used to reconstruct the deep geometry of the system emphasizing the modula-29 tion action of groundwater flow to the slope stability

Meningitis is a severe disease associated with death in children under five with highest rates of infections under age of one. Vaccines for Neisseria meningitides and Haemophilus influenza are used to prevent the main causative agents of meningitis. Administration of H. influenzae type b (Hib) vaccine is recommended at 2, 4 and 6 months with a booster dose at 18 months. N. meningitidis has two commercially available vaccines, the pure polysaccharide is recommended at 24 months meanwhile the protein-conjugated vaccines at 12 months. We sought in this study to examine if coadministering the vaccines for the two main meningitis causing bacteria might be synergistic as a preliminary step towards the possibility of shuffling immunization schedule. So, we coadministered Hib vaccine with commercially available vaccines either quadrate (ACWY) polysaccharide meningococcal (Men) or conjugated meningococcal (Nim) vaccines in Balb/C mice (n = 6/group) and compared to each vaccine administered separately and controls. Thirty-five days post immunization, we measured specific antibodies titers. Hib vaccine increased Men antibody titers significantly for serotypes Y and W. When Hib vaccine was coadministrated with Nim, antibody titer for Y, W and A significantly increased. For serotype C, there was no significant difference in antibody titers among immunized groups. As for effect of meningococcal vaccines on Hib, Men significantly increased Hib antibody titers while Nim had no effect. Collectively, our data suggested that coadministration of Hib and Men or Nim vaccines was safe and had synergistic effect on immune responses elicited to both vaccines. Further studies are needed before immunization schedule modifications. Such immunization schedule recommendation should provide better protection against this life-threatening disease in young children.

A vehicle boom barrier gate system is one of the recently developed technologies operating at the entrances to the restricted areas. This paper aims to design and control of vehicle’s boom barrier gate system using robust augmentation technique. H 2 optimal and H infinity synthesis controllers are used to improve the performance of the system. The open loop response analysis of the vehicle boom barrier gate system shows that the input of the system need to be improved. Comparison of the vehicle boom barrier gate system with H2 optimal and H infinity synthesis controllers have been done to track a set point desired angular position using a step and operational open and close input signals and a promising results have been observed.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

In recent years, the delivery of medical supplies has faced significant challenges due to natural disasters and recurrent public health emergencies. Addressing the need for improved logistics operations during such crises, this article presents an innovative approach integrating vehicle and Unmanned Aerial Vehicle (UAV) logistics to enhance the efficiency and resilience of medical supply chains. Our study introduces a dual-mode distribution framework that employs the Density-Based Spatial Clustering of Applications with Noise (DBSCAN) algorithm for efficiently clustering demand zones unreachable by conventional vehicles, thereby identifying areas requiring UAV delivery. Furthermore, we categorize the demand for medical supplies into two distinct sets based on vehicle accessibility, optimizing distribution routes via both UAVs and vehicles. Through comparative analysis, our findings reveal that the artificial bee colony (ABC) algorithm significantly outperforms the genetic algorithm in terms of solving efficiency, iteration counts, and delivery speed. However, the ABC algorithm's tendency towards early local optimization and rapid convergence leads to potential stagnation in local optima. To mitigate this issue, we incorporate a simulated annealing technique into the ABC framework, culminating in a refined optimization approach that successfully overcomes the limitations of premature local optima convergence. The experimental results validate the efficacy of our enhanced algorithm, demonstrating reduced iteration counts, shorter computation times, and substantially improved solution quality over traditional logistic models. The proposed method holds promise for significantly improving the operational efficiency and service quality of the healthcare system's logistics during critical situations.

This study evaluates the efficiency of biodegradable polyurethane foams as thermal insulation materials compared to conventional materials like expanded polystyrene (EPS). Key parameters analyzed include thermal conductivity, energy savings, CO2 emission reductions, and investment payback periods. Biodegradable polyurethane foams demonstrated a thermal conductivity of 0.022 W/(m·K), significantly lower than EPS’s 0.035 W/(m·K), leading to higher energy savings. Calculations reveal an annual energy saving of 443,820 kWh for polyurethane foams, compared to 441,330 kWh for EPS. Financially, polyurethane foams save approximately €53,258.4 annually, while EPS saves €52,959.6. In terms of environmental impact, polyurethane foams reduce CO2 emissions by 88,764 kg annually, versus 88,266 kg for EPS. Despite the higher initial cost of polyurethane foams (€50/m² compared to €30/m² for EPS), the payback period is remarkably short at 0.094 years (1.13 months) compared to EPS’s 0.057 years (0.68 months). These findings highlight biodegradable polyurethane foams as a superior option for thermal insulation, offering significant energy, financial, and environmental benefits.

A problem of efficacy of crystal growth methods for crystallization from solution or melt has been investigated. Axial vibrational control (AVC) technique was considered as a perspective method to manage both heat-mass transfer and chemical component composition of the melts in the case of crystallization of complex chemical compounds. Numerical modeling and the search for generalized dependencies made it possible to predict the AVC parameters that provide optimal heat and mass transfer modes for creating flat liquid-solid interfaces, as well as the component composition of dissociated melts of various chemical compounds – Ge, NaNO3, CdTe.

Toll plaza optimization is essential for improving traffic flow and easing congestion on road networks. This study aims to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer facilitation. Different resources are used for data collection, like the National Highway Authority of Pakistan. Physical data is collected from the established Toll Plaza of Peshawar, along with the development of each line. The goal of this study is to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer happiness. The analysis of present traffic patterns, the detection of bottlenecks, and the creation of plans to ease congestion and enhance overall traffic flow are all part of the optimization process. The approaches used in this study include data analysis, simulation, and traffic modeling. PTV VISSIM is software for transportation planning, design, and analysis. The simulations consider various conditions, such as variable traffic volumes, toll collection methods, and lane configurations. When comparing the different optimization strategies, performance indicators like trip time, latency, and queue length are utilized to determine which approach is practical. Waiting time Vs. Existing each lane, etc, is explained. In the end, comparing queue lengths and throughput across different lane scenarios shows that maximizing throughput with existing lanes yields up to 45% improvement with E-tag lanes, 40% with existing E-tag lanes, 38% with E-tag plus additional toll and cash lanes, 32% with three cash lanes, and 28% with two E-tag lanes. Failure to regularly monitor and adjust the existing lane pattern scenario based on traffic patterns can lead to queues being 20% longer. Without proactive evaluation and optimization, there is a potential 63% opportunity for queue length improvement

Some optimal control problems need metaheuristics in searching for the optimal solution, especially when the process has certain characteristics like the Photobioreactor for Algae Growth (distributed parameter, nonlinearities, etc.). Particle Swarm Optimization (PSO) algorithms within control structures are a realistic approach; their task is often to predict the optimal control values working with a process model (PM). Owing to numerous numerical integrations, there is a big computational effort that is reflected in a large controller execution time. The authors propose to replace the PSO predictor with a machine learning model that has “learned” the quasi-optimal behavior of the couple (PSO, PM); the training data is obtained through closed-loop simulations over the control horizon. The new controller should preserve the process’s quasi-optimal control. In identical conditions, the process evolutions must also be quasi-optimal. The multiple Linear Regression and the Regression Neural Networks were considered as predicting models. The paper first proposes algorithms for collecting and aggregating data sets for the learning process. Algorithms for constructing the machine learning models, implementing the controllers, and closed-loop simulations are also proposed. The simulations prove that the two machine learning predictors have learned the PSO predictor’s behavior such that the process evolves almost identically. The resulting controllers’ execution time drastically decreased while keeping their optimality.

Variable Angle Tow (VAT) laminates offer a promising alternative to classical straight fiber composites in terms of design and performance. However, analyzing these structures can be more complex due to the introduction of new design variables. Carrera's Unified Formulation (CUF) has been successful in previous works for buckling, vibrational, and stress analysis of VAT plates. Typically, one-dimensional (1D) and two-dimensional (2D) CUF models are used, with a linear law describing the fiber orientation variation in the main plane of the structure. The objective of this article is to expand the CUF 2D plate finite elements family to perform free vibration analysis of composite laminated plate structures with curvilinear fibers. The primary contribution is the application of Reissner's Mixed Variational Theorem (RMVT) to a CUF finite element model. The Principle of Virtual Displacements (PVD) and RMVT are both used as variational statements for the study of monolayer and multilayer VAT plates dynamic behavior. The proposed approach is compared to Abaqus three-dimensional (3D) reference solutions, classical theories and literature results to investigate the effectiveness of the developed models. Results demonstrate that mixed theories provide the best approximation of the reference solution in all cases.

Electrochromic measurements have been performed to optimize the composition of reactive magnetron-sputtered mixed layers of Zinc oxide and Tin oxide (ZnO-SnO2). A combinatorial material synthesis approach was applied throughout the deposition experiments, and the samples represented the full composition range of the binary SnO2-ZnO system. The Coloration Efficiency (CE) of the mixed oxide films were determined with simultaneous measurement of layer transmittance and applied electric current through the using organic propylene carbonate electrolyte cells in a conventional three-electrode configuration. Optical parameters and composition have been determined and mapped by using Spectroscopic Ellipsometry (SE). Scanning Electron Microscopy (SEM) with Energy-Dispersive X-ray Spectroscopy (EDS) has been used to check the SE results as it was used in our earlier paper [N. T. Ismaeel et al, Materials 2023, 16(12), 4204] for (TiO2-SnO2). Zn and Sn targets were put separately from each other, and the Indium-Tin-Oxide (ITO) covered glass and Si-probes on a glass substrate (30 cm × 30 cm) were moved under the two separated targets (Zn and Sn) in a reactive Argon-Oxygen (Ar-O2) gas mixture. By using this combinatorial process, all the compositions (from 0 to 100%) were achieved in the same sputtering chamber after one sputtering process. CE data evaluated from the primary data plotted against the composition displayed a characteristic maximum at around 29 % ZnO. Our combinatorial approach allows the localization of the maximum at 5% accuracy.

The article discusses issues related to the optimization of the operation of medium voltage networks, focusing on the optimization of network division points and the selection of the optimal network configuration aimed at reducing power and energy losses. The article provides a critical review of selected scientific works from recent years on the issue of network configuration optimization. The developed solution uses non-deterministic network models and statistical and probabilistic approaches. Optimization studies were carried out using heuristic optimization methods and proprietary algorithms for forecasting the load and power generated from renewable energy sources. The solution proposed in the article has many application possibilities. It can be used to optimize the location of network division points (reducing economic costs related to the modernization of network infrastructure) as well as to optimize the reconfiguration process in order to reduce power losses while maintaining voltage criteria.

In order to reduce the vibration of the transporter and improve the stability of the transporter, the vibration characteristics and key structure optimization research of the mountain orchard transporter are carried out. In this paper, the vibration of electric monorail transporters under different working conditions is tested, and the causes of vibration generated by monorail transporter during operation are explored. The three-dimensional model of the trailer and transmission box is established using Solidworks, and the modal vibration modes of the structure are analyzed theoretically. The modal test system is used for modal test analysis of trailers and transmission boxes. By comparing the results of finite element and experimental modal analysis, the second-order frequency of the trailer is close to the motor's rotating excitation frequency of 50 Hz at rated speed, which is easy to generate resonance. By optimizing the structure of the trailer, the second and third natural frequencies are increased to 54.79 Hz and 58.35 Hz respectively, which avoid the resonance of the trailer during operation and effectively reduce the vibration generated during the transportation of the trailer. Through vibration testing of the optimized electric monorail transporter, the results of vibration testing before and after structural optimization are compared and analyzed, and it is found that the vibration amplitudes of the transporter in X, Y and Z directions are reduced by 0.308m/s², 0.351m/s² and 0.334m/s² respectively, the running stability of the conveyer is improved.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

The goal of this research is to determine the optimal microwave-assisted sol-gel synthesis pa-rameters of TiO2 nanoparticles with the achievement of the crystalline TiO2 nanoparticles with the highest specific surface area and the lowest energy band gap. Titanium isopropoxide was used as a precursor to prepare the sol (colloidal solution) of TiO2, isopropanol as a solvent, acetylacetone for complexation, and nitric acid as a catalyst. Four samples of titanium dioxide were synthesized from the prepared colloidal solution in a microwave reactor at a temperature of 150 °C for 30 minutes and at a temperature of 200 °C for 10, 20, and 30 minutes. The phase composition of the prepared samples was determined by X-ray diffraction analysis (XRD) and Fourier-transform infrared spectroscopy (FTIR). Nitrogen adsorption/desorption isotherms were used to determine the spe-cific surface area and pore size distributions by Brunauer-Emmett-Teller (BET) method. The band gap energy values of the TiO2 samples were determined by diffuse reflectance spectroscopy (DRS). CrystallineTiO2 nanoparticles with the highest specific surface area and the lowest energy band gap were obtained for the TiO2 sample synthesized at 200 °C for 10 minutes.

In this paper, a completely different metaheuristic algorithm called the Orangutan Optimization Algorithm (OOA) is introduced, which replicates the complex and adaptive behaviors of Orangutans in their natural habitat. The main inspiration for OOA lies in the strategic foraging techniques of Orangutans, alongside their highly developed nesting abilities. More words are used to provide a detailed theoretical explanation of OOA, followed by a comprehensive modeling of the algorithm’s implementation in two key phases: exploration and exploitation. These phases are mathematically structured to ensure the balance required for optimal search processes. The performance of OOA is rigorously evaluated using twenty-nine benchmark functions from the CEC 2017 test suite, with problem dimensions of 10, 30, 50, and 100. More sentences are included to elaborate on the optimization outcomes, which reveal that OOA effectively balances the exploration and exploitation stages, yielding suitable and competitive solutions across the benchmark functions. Additionally, to further validate its quality, the results from OOA are compared against twelve other well-established metaheuristic algorithms. The analysis of these simulation results demonstrates that OOA consistently outperforms competing algorithms by achieving superior results across most benchmark functions. Furthermore, to assess its real-world applicability, OOA is implemented on a set of twenty-two constrained optimization problems drawn from the CEC 2011 test suite. The extended simulation results clearly indicate that OOA is highly efficient in solving real-world optimization challenges, consistently delivering a superior performance when compared to other competitor algorithms.

Hydro generator sets serve as the peak and frequency regulation of the power system,and play a very important role in maintaining system stability and improving power quality.Based on the internal characteristics model of a specific type of hydro generator,this paper constructs a hydroelectric coupling model for hydropower units,studies the influence of the regulation system of hydropower units on low-frequency oscillations under different load conditions,and adopts variable speed reaching law and fuzzy sliding mode control strategy to improve the regulation quality of the system and ensure the stable operation of the units.Results of simulation and water turbine set under different load conditions show that varible speed reaching law can effectively improve the power-angle oscillation behavior of the hydropower set and suppress the occurrence of low-frequency oscillations of the system when the system is subject to power disturbance,which provide a new theoretical basis and solution for the vibration analysis and control optimization of hydraulic turbine units.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

A variable speed anti-tangling reel mechanism was designed to address the problems of tangling, hanging and rewinding of the tassel wheel and the high paddling loss in the current Chinese rape combine harvester cutting table. The kinematic equations of the reel mechanism were developed, and the analysis showed that the speed in the entry stage is low and the speed in the exit stage is high, and the attitude of the reel teeth change with the rape plant movement during the whole paddling process. A single-factor test and a multi-factor regression orthogonal combination test were carried out using the cutting table loss rate of rape harvesting as the evaluation index. The main and secondary factors affecting the cutting table loss of the variable speed reel were obtained as the reel speed, the machine travel speed and the ground angle of the frame. A mathematical model of regression of cutter loss and the main influencing factors was established, with the coefficient of determination R2 = 0.9918. The optimal combination of parameters for the variable speed reel was obtained with the lowest cutting table loss rate in rape harvesting as the optimization target: reel speed 25r/min, frame parallel to the ground and implement travel speed 0.7m/s. Field validation tests and comparative tests of cutting table loss of the two reels were carried out. The test results show that the regression mathematical model of the cutting table loss is more accurate, and the cutting table loss is reduced by 13.9% with the variable speed reel compared to the cam-action reel, and there are no problems with the paddle teeth hanging and tangling during the paddling process.

For the first time to optimize the creation of new neuroprotective agents based on bioflavonoids, we applied information technologies - docking analysis to calculate the binding of candidate molecules to the pharmacological target protein transthyretin, as well as the program of virtual screening of NO scavengers. As a result of this approach, the substance catechin was isolated from candidate molecules - quercetin, catechin, Epicatechin gallate, Epicatechin, Procyanidin B1, Procyanidin B2, Procyanidin B3, Catechin-3-gallate according to docking analysis. As a result of virtual screening, catechin was identified as a potential NO scavenger (55.15% prediction). The results of the prediction were confirmed by in vitro experiments. Course administration of catechin to animals with experimental multiple sclerosis (MS) against the background of methylprednisolone administration completely eliminated lethal cases, reduced the number of diseased animals by 20%, as well as prevented the development of severe neurological symptoms by 20% (compared to the methylprednisolone group) and by 60% compared to the control group. Course administration of catechin with methylprednisolone leads to decrease of neurodegradation markers in the cytosol of rats with EAE: NSE by 37%, and S-100 - by 54.8%. The combined administration of methylprednisolone significantly exceeds the combination of methylprednisolone with the reference drug mexidol by the degree of NSE reduction. The obtained results indicate a significant neuroprotective effect of ocular combinations of methylprednisolone and catechin. The above-mentioned confirms the correctness of bioflavonoid selection with the help of virtual screening program.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Smartwatches are one of the most relevant fitness trends of the past two decades, and they collect increasing amounts of health and movement data. The accuracy of these data may be questionable and requires further investigation. Therefore, the aim of the present study is to validate smartwatches for use in triathlon training. Ten different smartwatches were tested for accuracy in measuring heart rate, distance (via global navigation satellite systems, GNSS), swim stroke rates and the number of swim laps in a 50 m Olympic-size pool. The optical heart rate measurement function of each smartwatch was compared to that of a chest strap. Thirty participants (15 females, 15 males) ran five 3-minute intervals on a motorised treadmill to evaluate the accuracy of the heart rate measurements. Moreover, for each smartwatch, running und cycling distance tracking was tested over six runs of 4,000 m on a 400 m tartan stadium track, six hilly outdoor runs over 3.4 km, and four repetitions of a 36.8 km road bike course, respectively. Three swimming protocols ranging from 200 m to 400 m were performed in triplicate in a 50 m Olympic-size pool, evaluating tracked distance and detected number of strokes. The mean absolute percentage errors (MAPEs) for the average heart rate measurements varied between 3.1% and 8.3%, with the coefficient of determination ranging from 0.22 to 0.79. MAPE results ranged from 0.8% to 12.1% for the 4,000 m run on the 400 m track, from 0.2% to 7.5% for the 3.4 km outdoor run, and from 0.0% to 4.2% for the 36.8 km bike ride. For the swimming tests, in contrast, the deviations from the true distance varied greatly, starting at a 0.0% MAPE for the 400 m freestyle and reaching 91.7% for the 200 m medley with style changes every 25 m. In summary, for some of the smartwatches, the measurement results deviated substantially from the true values. Measurements taken while road cycling over longer distances with only a few curves were in relative terms more accurate than for outdoor runs and even more accurate than for the 400 m track. In the swimming exercises, the accuracy of the measured distances was severely deteriorated by the medley changes among the majority of the smartwatches. Altogether, the results of this study should help in assessing the accuracy and thus suitability of smartwatches for general triathlon training.

This article introduces a novel nature-inspired metaheuristic algorithm called Frilled Lizard Optimization (FLO), which emulates the hunting behavior of frilled lizards in their natural habitat. FLO draws in-spiration from the sit-and-wait strategy observed in frilled lizards during hunting. The underlying theory of FLO is presented and mathematically formulated in two phases: (i) an exploration phase, simulating the frilled lizard's attack towards prey, and (ii) an exploitation phase, simulating the lizard's retreat to the top of the tree after feeding. To assess FLO's efficacy in solving optimization problems, the algorithm's performance is evaluated across fifty-two standard benchmark functions, encompassing unimodal, high-dimensional multimodal, fixed-dimensional multimodal, and the CEC 2017 test suite. Comparative analyses with twelve existing metaheuristic algorithms are conducted. The simulation results reveal that FLO, distinguished by its adeptness in exploration, exploitation, and balancing them during search process, outperforms competing algorithms. Additionally, FLO is implemented on twenty-two constrained optimization problems from the CEC 2011 test suite and four engineering design problems, demonstrating its effectiveness in addressing real-world optimization applications.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

This study examines the potential of implementing a systematic approach to piloting desalination plants, with the objective of evaluating energy improvements in water desalination processes. The global scarcity of freshwater resources has significantly influenced the development of desalination technologies, with reverse osmosis emerging as one of the most prevalent and highly regarded methods. Pilot tests with the latest generation of reverse osmosis membranes in large desalination plants are becoming increasingly common. This is due to the fact that small-scale experiments are being carried out on the operation of new generation membranes with better salt rejection and lower energy consumption. The objective of this approach is to achieve the optimal water quality standard at the lowest possible cost. In this manner, pilot tests are being conducted prior to the determination of whether to alter the reverse osmosis membranes, as this represents a substantial investment. The objective of these tests is to minimise the risk of making an erroneous decision and to ensure optimal results in terms of energy consumption, operating costs and reduction of environmental impact, while complying with the requisite water quality standards. In this case, the Pareto analysis is employed to identify the two or three most significant causes whose treatment affects more than 80% of the potential energy savings to be implemented. This article introduces a novel approach to studying a total of 180 desalination plants at the territorial level in the Canaries.

The present study deals with the transplantation of mature Argan trees (Argania spinosa L. Skeels) and focuses on optimizing survival rates depending on the seasons, the type of shoot pruning applied to the trees and preconditioning treatments consisting of root pruningand watering for a few months before transplanting. So far, the transplantation of this species at the adult stage has not received enough attention in spite of its ecological and socio-economic importance for the regions where it thrives. The results obtained show that transplanting in summer, autumn and winter resulted in survival rates exceeding 50%. The Argan trees transplanted in spring hardly achieved 10% survival. However, the total cutback of the crown induced survival improvement that reached a rate greater than 70% for summer, autumn and winter, and 50% for spring. Watering alone or combined with root pruning for 6 months helped improve the recovery rate but only when carried out in autumn with transplantation in spring. On the other hand, when these pre-treatments were applied in the spring to transplant the trees in summer, the recovery rate was not improved.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

The power-generation capacity of grid-connected photovoltaic (PV) power systems is increasing. As output power forecasting is required by electricity market participants and utility operators for the stable operation of power systems, several methods have been proposed using physical and statistical approaches for various time ranges. A short-term (30 min ahead) forecasting method has been previously proposed by our laboratory for geographically distributed PV systems using motion estimation. This study focuses on an important parameter for estimating the proposed motion and optimizing the parameter. This parameter is important because it is associated with the smoothness of the vector field, which is the result of motion estimation and influences the forecasting accuracy. In the periods with drastic power output changes, the evaluation was conducted on 101 PV systems located within a circle of 15-km radius in the Kanto region of Japan. The results indicate that the absolute mean error of the proposed method with the optimized parameter is 10.3%, whereas that of the persistent prediction method is 23.7%. Therefore, the proposed method is effective in forecasting for periods when PV output changes drastically in a short time.

Arthroplasty is commonly performed to treat advanced osteoarthritis or other degenerative joint conditions, but it can also be considered for young patients with severe joint damage that significantly limits their functionality and quality of life. Young patients are still at risk of aseptic mobilization and bone resorption due to the phenomenon of stress-shielding that causes an uneven distribution of tensions along the femoral contact surface prosthesis. This phenomenon can be limited by appropriately choosing the material of the prosthesis or by varying its stiffness, making sure that its mechanical behavior simulates that of the femur as much as possible. The aim of this study is to evaluate the mechanical behavior of a prosthesis optimized both in shape and material and in comparing the results with a standard titanium prosthesis. Methods: Through three-dimensional modeling and the use of software finite element method (FEM) such as ANSYS we simulate the mechanical behavior of traditional prosthesis and prosthesis optimized topologically respecting the ASTM F2996-13 standard Results: With topological optimization there is a stress reduction from 987 Mpa to 810 Mpa with a mass reduction of 30%. With the use of carbon fiber, it is possible to further reduce stress to 509 Mpa. Conclusions: The reduction of stress on the femoral stem allows an optimal distribution of the load on the cortical bone thus decreasing the problem of stress-shielding.

Understanding the interrelationships between land use, climate change, and regional water yield is critical for effective water resource management and ecosystem protection. However, comprehensive insights into how water yield evolves under different land use scenarios and climate change remain elusive. This study employs the Integrated Valuation of Ecosystem Services and Trade-offs (InVEST) models, Patch-generating Land Use Simulation (PLUS) model, and Geodetector within a unified framework to evaluate the dynamics of land use, water yield, and their relationships with various factors (meteorological, social, economic, etc.). To forecast the Land Use/Cover Change (LUCC) pattern of the Yellow River Basin by 2030, three scenarios were considered: economic development priority (Scenario1), ecological development priority(Scenario2), and cropland development priority(Scenario3). Climate change scenarios were constructed using CMIP6 data, representing low stress (SSP119), medium stress (SSP245), and high stress (SSP585) conditions. The results show the following: (1) From 2000 to 2020, cropland was predominant in the Yellow River Basin, Henan Province, with significant land conversion to impervious land (construction land) and forest land; (2) Water yield changes during this period were primarily influenced by meteorological factors, with land use changes having negligible impact; (3) By 2030, the water yield of Scenario1 is highest among different land use scenarios, marginally surpassing ecological development priority by 0.5%; (4) Climate scenarios reveal significant disparities, with SSP126 yielding 67% higher water production than SSP245, driven predominantly by precipitation; (5) Geodetector analysis identifies precipitation as the most influential single factor, with significant interactions among meteorological and socio-economic factors. These findings offer valuable insights for policymakers and researchers in formulating land use and water resource management strategies.

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimising MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based-control and deep learning techniques, including gated recurrent units (GRU), basic recurrent neural network (RNN) and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimises MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyper-parameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R2 value close to 1, representing a strong correlation between predicted and actual power values.

This paper presents experimental identification and vibration suppression of a flexible manipulator with non-collocated piezoelectric actuators and strain sensors using optimal multi-poles placement control. To precisely identify the system model, a reduced order transfer function with relocated zeros is proposed, and a first-order inertia element is added to the model to compensate the non-collocation. Comparisons show the identified model match closely with the experimental results both in the time and frequency domains, and a fit of 97.2% is achieved. Based on the identified model, a full-state multi-poles placement controller is designed, and the optimal locations of the closed loop poles are determined. The feasibility of the proposed controller is validated by simulations. Moreover, the controller is tested for different locations of the closed loop poles, and an excellent performance of the optimal locations of the closed loop poles is shown. Finally, the effectiveness of the proposed controller is demonstrated by experiments. Results show that the vibrations of the expected modes are significantly diminished. Besides, vibrations of the higher modes are also slightly suppressed. Accordingly, multi-mode vibrations of the manipulator are well attenuated, and the tip displacement converges quickly with the proposed method.

Mathematical optimization offers a valuable approach to tackle Industry scheduling problems. By formulating the scheduling challenge as a mathematical problem, mathematical optimization enables efficient and effective decision-making processes. Mathematical optimization is particularly beneficial in complex scheduling scenarios, such as in networked manufacturing environments, where multiple jobs and resources need to be coordinated. By leveraging optimization models and algorithms, it becomes possible to generate optimal process plans, considering factors like job dependencies, resource availability, and timing constraints. Through mathematical optimization, organizations can achieve improved efficiency, reduced lead times, and enhanced utilization of resources. Rigorous mathematical formulations and optimization techniques enables to surpass traditional manual planning methods and brings forth powerful computational capabilities. By optimizing various scheduling objectives, from minimizing makespan to maximizing resource utilization, mathematical optimization provides organizations with valuable insights and actionable plans. The purpose of this study is to discuss scheduling solutions for multiple jobs in a networked manufacturing setting based on mathematical optimization process. The study analyses a solver-based approach to generate the optimal process plans for multiple jobs and compare it with a more traditional game-theoretic approach. The objectives aim to develop two solver-based model using Z3 and Gurobi to generate optimal process plans; implement a game-theoretic model to solve for the same set of scheduling problems, and compare the computational time, solution quality, and efficiency of both approaches. To achieve this, the methodology will start with the problem definition. Multiple jobs are to be scheduled on a set of parallel machines. Each job has predefined processing times, deadlines, and priorities. The objective is to minimize the total completion time and maximize machine utilization while meeting all deadlines.

Quantum optimization is a significant area of quantum computing with anticipated near-term quantum advantages. Current quantum optimization algorithms, most of which are hybrid variational Hamiltonian-based algorithms, struggle on present quantum devices due to noise and decoherence. Existing techniques attempt to mitigate these issues through employing different Hamiltonian encodings or Hamiltonian clause pruning but often rely on optimistic assumptions rather than a deep analysis of the problem structure. We demonstrate how to formulate the problem Hamiltonian for the Quantum Approximate Optimization Algorithm to satisfy all the requirements that correctly describe the considered tactical aircraft deconfliction problem, achieving higher probabilities of measuring solutions compared to previous works. Our results indicate that constructing Hamiltonians from an unconventional, quantum-specific perspective with a high degree of entanglement results in linear number of entangleming gates instead of exponential and superior performance compared to standard formulations. Specifically, we achieve higher probabilities of measuring feasible solutions in 9 out of 9 instances compared to standard Hamiltonian formulations and surpass quadratic programming formulations known from quantum annealers in 7 out of 9 instances. These findings suggest that there is substantial potential for further research in quantum Hamiltonian design and that gate-based approaches may offer superior optimization performance over quantum annealers in the future.

The goal of the manuscript is to design a relatively best control structure for the noise suppression of a drone’s camera gimbal action. The gimbal’s movement can be simplified as a rest-to-rest reorientation system that can achieve the boundary result of a dynamic system. Six different control architectures are proposed and evaluated based on their ability to control the trajectory of the dynamic-system position and speed, their running time, and quadratic cost. The robustness of the control architecture to uncertainties in inertia and sensor noise is also analyzed. Monte Carlo figures are used to assess the performance of the six control systems. The conditions for applying different architectures are identified through this analysis. The analysis and experimental tests reveal the most suitable control of the drone’s camera gimbal rotation.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

The dynamic behaviour of a machine tool (MT) directly influences the machining performances. The adoption of lightweight structures may reduce the effects of undesired vibrations and increasing the workpiece quality. This paper aims to present and compare a set of hybrid materials that may be excellent candidate to fabricate the MT moving parts. The selected materials have high dynamic characteristics and capacity to damp mechanical vibrations. In this way, starting by the kinematic model of a milling machine that highlights the main critical factors, this study paper evaluates a number of prototypes made of Al Foam sandwiches (AFS), Al Corrugated sandwiches (ACS) and materials reinforced by carbon fibres (CFRP). A set of prototypes has been fabricated, represented the Z-axis ram of a commercial milling machine. The static and dynamical properties have been evaluated by using both FE simulations and experimental tests. The obtained results show that the proposed structures may be a valid alternative to the conventional materials of MT moving parts, increasing machining performances. In particular, the AFS prototype highlighted a damping coefficient that is 20 times greater than a conventional ram (e.g. steel). The CFRP structure is able to satisfy the machining requirements with a reduced weight of 48.5%, while the ACS prototype showed a good trade-off between stiffness and damping.

In March 2013, a novel avian influenza A H7N9 virus was emerged in China, which cause rapidly progressive pneumonia and with a high fatality rate. Serologic studies to evaluate neutralizing antibodies of infected patients and birds are invaluable tools for immunogenicity research of H7N9 and epidemiological investigation. Conventional neutralization assays are laborious and time-consuming which also hampered by biosafety requirement. In this study, We construct and produce pseudovirus bearing the full-length hemagglutinin (HA) of H7N9 virus in the Env-defective, luciferase-expressing HIV-1 backbone. The production of lentiviral pseudovirus was analysed by HA gene specific real-time reverse-transcription PCR, transmission electron microscopy (TEM), and Western Blot assay to prove the nucleic acid replication, the morphology of virus, and the expression of HA protein in pseudovirus. After that pseudovirus based inhibition assay was established to detect neutralizing antibodies of a panel of serum samples. Our results demonstrated that H7N9 pseudovirus which had single-cycle infection was generated. By comparing the neutralization antibody titers, pseudovirus based neutralization test could be recognized as an alternative of conventional microneutralization (MN). Hence, we conclude that it is possible to use pseudovirus inhibition assay to screen sera samples, as well as evaluate vaccine-induced neutralizing antibodies against H7N9 virus.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

Managing a portfolio whose value closely tracks an index by trading only in a subset of the index constituents involves an NP-hard optimisation problem. In the prior literature, it has been suggested to solve this problem using sequential Monte Carlo (SMC, a.k.a. particle filter) methods. However, this literature does not take transaction costs into account, although transaction costs are the primary motivation for attempting to replicate the index by trading in a subset, rather than the full set of index constituents. This paper extends the SMC approach to index tracking to allow for proportional transaction costs and implements this extended method on empirical data for a variety stock indices. In addition to providing a more practically useful tracking strategy by allowing for transaction costs, we find that including a penalty for transaction costs in the optimisation objective can actually lead to better tracking performance.

Identification the parameters of triple-diode electrical circuit structure of PV-module is a challenging issue and has been emphasized as an important research area. Accordingly, a hybrid evolutionary optimization algorithm is presented in this paper. Differential evolution algorithm (DEA) is hybridized with electromagnetism-like algorithm (EMA) in the mutation stage to enhance the reliability and efficiency of DEA. The presented algorithm is called differential evolution with integrated mutation per iteration (DEIMA). A new formula is presented to adapt the control parameters (mutation factor and crossover rate) of DEA and is based on a sigmoid function in terms of the current and previous fitness function values. Seven different experimental data sets are used to assess the performance of the proposed DEIMA. The results of the proposed PV modeling method are evaluated with other approaches in literature. According to different statistical criteria, DEIMA offered superiority in terms of root mean square error and main bias error by at least 5.4% and 10%, respectively, as compared to other methods. Furthermore, DEIMA needs 27.69 sec. as an average execution time less than other compared methods.

The influence of neutrosophy in the previous period is constantly growing in many areas of science and technology. Moreover, various applications of the neutrosophic approach have become more common in recent years. Our goal in this research is to utilize the neutrosophy to improve the performance of the Dai-Liao conjugate gradient (CG) method. Specifically, in this research, we propose and investigate a new neutrosophic logic system to calculate the key parameter t involved in the Dai–Liao CG iterations. Theoretical analysis and numerical experience indicate that the efficiency and robustness of the new rule for determining t. Combining the neutrosophy and the Dai-Liao conjugate gradient method, we propose and explore a new Dai-Liao CG iterations for solving large-scale unconstrained optimization models. The global convergence is established under common assumptions and the backtracking line search. Finally, by conducting numerical experiments, computational evidence demonstrates that the new fuzzy neutrosophic Dai-Liao conjugate gradient method is computationally effective and robust.

Abstract: Peptide pools composed of short amino acid sequences have proven to be versatile tools in various research areas and clinical applications. They are powerful tools for epitope mapping, immunotherapy, and vaccine development. Their importance lies in their ability to map complex protein structures, enabling a comprehensive understanding of immune responses and facilitating the identification of potential therapeutic agents. The application of peptide pools also extends to the field of personalized medicine, offering tailored solutions for diseases such as cancer and infectious diseases. Peptide pools are complex mixtures of immunostimulatory antigens primarily intended for T-cell stimulation. They are commercially available in many different compositions and variants. However, unlike other reagents that consist of only one or a few compounds, peptide pools are highly complex products with limited stability. This makes their quality control a major challenge. Quantitative peptide analysis usually requires sophisticated methods, in most cases isotope-labeled standards and reference materials. None of these are routinely available for these products. Synthesis and purification of all labeled peptides might be required. Usually, this approach would be prohibitively laborious and expensive. Therefore, an approach is needed to provide a practical and feasible method for quality control of peptide pools. With insufficient quality control, the use of such products could lead to incorrect experimental results, which would worsen the well-known reproducibility crisis in the biomedical sciences. Here we propose the use of ultra-high performance liquid chromatography (UHPLC) with two detectors, a standard UV detector (at 214 nm) for quantitative analysis and a high-resolution mass spectrometer (HRMS) for identity confirmation. To be cost-efficient and fast, quantification and identification are performed in one chromatographic run. An optimized protocol is shown, and different peak integration methods are compared and discussed. This work was performed using a peptide pool known as CEF, which consists of 32 peptides derived from cytomegalovirus (CMV), Epstein-Barr virus (EBV) and influenza virus, ranging from 8 to 12 amino acids in length.

This article investigates the effectiveness of feature extraction and selection techniques for enhancing the performance of classifiers accuracy in Type II Diabetes Mellitus (DM) detection using microarray gene data. To address the inherent high dimensionality of the data by employing three Feature Extraction (FE) methods are used namely, Short-Time Fourier Transform (STFT), Ridge Regression (RR), and Pearson Correlation Coefficient (PCC). To further refine the data, meta-heuristic algorithms like Bald Eagle Search Optimization (BESO) and Red Deer Optimization (RDO) are utilized for feature selection. The performance of seven classification techniques such as Non-Linear Regression - NLR, Linear Regression - LR, Gaussian Mixture Model - GMM, Expectation Maximization - EM, Logistic Regression - LoR, Softmax Discriminant Classifier - SDC, and Support Vector Machine with Radial Basis Function kernel - SVM-RBF are evaluated with and without feature selection. The analysis reveals that the combination of PCC with SVM-RBF achieved a promising accuracy of 92.85% even without feature selection. Notably, employing BESO with PCC and SVM-RBF maintained this high accuracy. However, the highest overall accuracy of 97.14% was achieved when RDO was used for feature selection alongside PCC and SVM-RBF. These findings highlight the potential of feature extraction and selection techniques, particularly RDO with PCC, in improving the accuracy of DM detection using microarray gene data.

The Cyber Security Incident Response Team executes its critical duties in the Centralized Security Operation Centers. Its primary target is to protect organizational resources from all types of Advanced Persistent Threats (APT) and attacks while making the correct judgments at the right time. Despite the great efforts and the efficient tools, the incident response mechanism faces two significant challenges. The generation of large amounts of alerts with huge rates of false positives per unit of time and the time-consuming manual expert engagement in the post-alert decision phase. The main aim of this research study is to investigate the potential of Machine Learning techniques in solving the above challenges. This study proposes six event detection modules to identify 14 different types of malicious behavior using Splunk. The available APT dataset is extended by adding more alert types. Then, the machine learning techniques i.e., Random Forest, and XGBoost, are applied to improve the decision process and reduce the false positive alerts of the Security Information and Event Management system. The proposed model outperforms the state-of-the-art techniques by predicting an accuracy of 99.6%.

The integration of diverse distributed generation (DG) units, encompassing both Renewable Energy Sources (RES) and non-RES technologies delves into voltage levels, current distributions, and power flows, aiming to optimize and effectively manage the distribution network. An RES-based DGs such as photovoltaic systems and wind turbines, alongside non-RES units like fuel cells and micro turbines. This study proposes a hybrid approach the Multi-Objective Genetic Algorithm - Grey Wolf Optimizer (MOGA-GWO). By merging the strengths of multi-objective genetic algorithms with the efficiency of the Grey Wolf Optimizer, this advanced algorithm seeks semi-optimal solutions for multi-objective optimization problems. The algorithm aims to improve convergence speed without compromising solution quality, offering a promising solution for optimizing the characteristics of DG and RES integration in distribution networks compared to Cuckoo Search and Simulation Annealing Techniques. Key algorithmic operations include individual representation, initialization, fitness function computation, selection, crossover, mutation, and ending conditions. The DG optimal power flow problem is explored with a focus on minimizing generation costs, improving voltage profiles, minimizing losses, enhancing reliability, integrating renewable energy, reducing environmental impact, managing congestion, and ensuring compliance with operational constraints. Beyond traditional considerations, the study emphasizes neglected objectives and constraints, such as cyber-security concerns, real-time operation, regulatory frameworks, social acceptance, lifecycle environmental impact, grid resilience, data privacy, aging infrastructure compatibility, and economic viability.

Nowadays circular economy trend drives researchers in the recovery of various bioactive compounds from agri-food by-products. Enzyme-assisted extraction (EAE) is shown as an innovative green technology for the effective extraction of various phytochemicals from agri-food section by-products, therefore this study aimed to evaluate the application of EAE as green technology to obtain extracts from olive leaves (Olea europaea) for potential industrial production. EAE was conducted under various enzyme dose combinations, and incubation time (120 min). Obtained extracts were characterized in terms of total polyphenols (TP) and Total Antioxidant Activity (AA). Firstly, the enzyme synergistic effect in enzymatic extraction of polyphenols was evaluated. TP optimal extraction conditions (468.19 mg GAE/L) were achieved after EAE (50-50%) and for AA (69.85 AA%). According to the above results, a second experimental part occurred for the incubation time (min.) and enzyme dose (mL) of optimal extraction conditions of olive leaves. Results indicated EAE as an excellent choice for green extraction of polyphenols from the olive leaves.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

The methods of Artificial Intelligence (AI) have been used in the planning and operation of power systems for more than 40 years. In recent years, due to the development of microprocessor and data storage technologies, the effectiveness of this use has greatly increased. This paper provides a systematic overview of the application of AI including the use of Machine Learning (ML) to the power system. The potential application areas are divided into four blocks and the classification matrix has been used for clustering the AI application tasks. Furthermore, the data acquisition methods for setting the parameters of AI and ML algorithms are presented and discussed in a systematic way considering the supervised and unsupervised learning methods. Based on this, three complex application examples: wind power generation forecasting, smart grid security as-sessment (using two methods), and automatic system fault detection are presented and discussed in detail. Summary and outlook conclude the paper.

The optimization methods are increasingly used to solve challenging problems of aeronautical engineering. Typically, the optimization methods are utilized in design of aircraft airframe or its structure. The presented study is focused on an improvement of aircraft-flight-control procedures through the numerical optimization approach. The optimization problems concern selected phases of flight of light gyroplane - a rotorcraft using an unpowered rotor in autorotation to develop lift and an engine-powered propeller to provide thrust. An original methodology of computational simulation of rotorcraft flight was developed and implemented. In this approach the aircraft-motion equations are solved step-by-step, simultaneously with the solution of the Unsteady Reynolds-Averaged Navier-Stokes equations, which is conducted to assess aerodynamic forces acting on the aircraft. As a numerical optimization method, the BFGS algorithm was adapted. The developed methodology was applied to optimize the flight-control procedures in selected stages of gyroplane flight in direct proximity of the ground, where properly conducted control of the aircraft is critical to ensure flight safety and performance. The results of conducted computational optimizations proved qualitative correctness of the developed methodology. The research results can be helpful in design of easy-to-control gyroplanes and also in the training of pilots of this type of rotorcraft.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

This study investigated the efficiency of scale-propellers, typically used on small drones. A scale-propeller is accepted as having a diameter of 7 to 21 inches. The Ukraine War has demonstrated the utility of relatively small, low-cost first-person view (FPV) drones, which are attritable. This investigation outlines the development of a MATLAB optimisation code, based on minimum induced loss propeller theory, which calculates the optimal chord and twist distribution for a chosen propeller operating in known flight conditions. The MATLAB code includes a minimum Reynolds number functionality, which provides the option to alter the chord distribution to ensure the entire propeller is operating above a set threshold value of Reynolds (>100,000), as this has been found to be a transition point between low and high section lift-to-drag ratios. Additional functions allow plotting of torque and thrust distributions along the blade. The results have been validated on experimental data taken from an APC ‘Thin Electric’ 10” x 7” propeller, where it was found that both the chord and twist distributions were accurately modelled. The MATLAB code resulted in a 16% increase in the maximum propulsive efficiency. Further work will investigate a direct interface to SolidWorks to aid rapid propeller manufacturing capability.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

In pattern recognition domain, deep architectures are widely used nowadays and they have achieved fine grades. However, these deep architectures need special demands, especially big datasets and GPU. Aiming to gain better grades without deep networks, we propose a simplified algorithm framework using fusion features extracted from the salient areas of faces. Furthermore, the proposed algorithm has achieved a better result than some deep architectures. For extracting more effective features, this paper firstly defines the salient areas on the faces. This paper normalizes the salient areas of the same location in the faces to the same size, therefore it can gain more similar features from different subjects. LBP and HOG features are extracted from the salient areas, fusion features’ dimensions are reduced by Principal Component Analysis( PCA) and we apply softmax to classify the six basic expressions at once. This paper proposes a salient areas definitude method which uses peak expressions frames to compare with their neutral faces. This paper also proposes and applies the idea of normalizing the salient areas to align the specific areas which express the different expressions. This makes the salient areas found from different subjects have the same size. Besides, gamma correction method is firstly applied on LBP features in our algorithm framework which improves our recognition rates significantly. By applying this algorithm framework, our research has gained state-of-the-art performances on CK+ database and JAFFE database.

Background: Despite its global eradication in 1977, smallpox remains a concern owing to its potential as a biological agent, thereby prompting the ongoing development and utilization of its vaccine. Vaccination with the Vaccinia virus induces immunity against variola virus, the causative agent of smallpox; however, this immunity does not extend to viruses of different genera within the Poxviridae family. In this study, we aimed to assess the efficacy of an enzyme-linked immunosorbent assay (ELISA) method utilizing Vaccinia virus and recombinant A27L antigen for detecting antibodies against smallpox. Methods. Analysis of serum from 20 individuals pre- and post-vaccination with the CJ strain (CJ50300) revealed neutralizing antibodies, which were confirmed using the plaque reduction neutralization test (PRNT). The ELISA method, validated with a PRNT50 cut-off value of >4, exhibited a sensitivity and specificity of >95% and was particularly reactive with the inactivated virus. Furthermore, adherence to the smallpox vaccination policy revealed significant differences in Orthopoxvirus antibody levels among 300 individuals of different age groups. These findings highlight the reliability and efficacy of the ELISA method in detecting post-vaccination antibodies and contribute significantly to diagnostic methods to prepare for potential smallpox resurgence and bioterrorism threats.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Sources are classified into two depending upon the factor of reviving. These sources, which cannot be revived into their original shape once they are consumed, are considered as nonrenewable energy resources, i.e., (coal, fuel) Moreover, those energy resources which are revivable to the original condition even after being consumed are known as renewable energy resources, i.e., (wind, solar, hydel) Renewable energy is a cost-effective way to generate clean and green electrical energy Now a day’s majority of the countries are paying heed to energy generation from RES Pakistan is mostly relying on conventional energy resources which are mostly nonrenewable in nature coal, fuel is one of the major resources, and with the advent of time their prices are increasing on the other hand RES have great potential in the country with the deployment of RES greater reliability and an effective power system can be obtained In this thesis, a similar concept is being used and a hybrid power system is proposed which is composed of intermixing of renewable and nonrenewable sources The Source side is composed of solar, wind, fuel cells which will be used in an optimal manner to serve load The goal is to provide an economical, reliable, uninterruptable power supply. This is achieved by optimal controller (PI, PD, PID, FOPID) Optimization techniques are applied to the controllers to achieve the desired results. Advanced algorithms (Particle swarm optimization, Flower Pollination Algorithm) will be used to extract the desired output from the controller Detailed comparison in the form of tables and results will be provided, which will highlight the efficiency of the proposed system.

In this paper, a thermodynamic investigation is done on a Kalina-flash cycle. This work is initially validated with the Kalina cycle power plant, Wich is commissioned in Husavic. Low-temperature Kalina-flash is considered for this study. This cycle is working with the ammonia-water mixture. The Kalina-flash cycle was optimized in the view of exergy and thermal efficiency. A multi-objective genetic algorithm is used to accomplish optimization. The optimum values of the objective functions are observed to be 40.20 and 11.70% respectively. At last, The influence of the separator inlet dryness fraction, basic ammonia mass fraction, temperature and flash pressure ratio on the first and second law efficiencies are analysed.

The evidential value of an mtDNA match between biological remains and its potential donor is determined by the random match probability of the haplotype. This probability is based on the haplotype’s population frequency estimate. Consequently, implementing a population study representative of the population relevant to the forensic case is vital to correctly evaluating the evidence. The emerging number of poaching cases and the limited availability of such data emphasizes the need for improved fallow deer mtDNA population databank for forensic purposes, including targeting the entire mitochondrial control region. By sequencing the whole mitochondrial control region in 138 animals from five populations in Hungary we found four different haplotypes, including one which has not yet been described. Our results, supplemented with data already available from previous research do not support the possibility of determining the population of origin, although some patterns of geographical separation can be distinguished. Estimates of molecular diversity indicate approximately similarly low mtDNA diversity (Hd=0.565 and π = 0.002), compared with data from other countries. The calculated random match probability of 0.547 shows a high probability of coincidence and, therefore, a limited capacity for exclusion. Consequently, it may be necessary to search for polymorphic sites on other mitochondrial gene sections or to sequence the entire mitogenome of fallow deer.

Acid-producing bacteria in pit mud play a crucial role in the fermentation of Chinese liquor, significantly influencing its flavor, taste, and overall quality. This study investigates three strains of anaerobic acid-producing bacteria from pit mud to optimize both single and combined bacterial fermentations for enhanced acid production. Acid production levels were quantitatively measured using gas chromatography-mass spectrometry. The Design Expert software was employed to identify significant nutritional factors affecting the production of hexanoic and butyric acids. These factors were optimized through climbing tests and response surface analysis. The Box-Behnken Design (BBD) experimental design and variance analysis were used to determine the optimal levels of each significant factor. The SJ-1/SJ-3/SJ-8/enriched solution exhibited the highest acid production, with a total acid production of 2216.07±0.10 mg/100 ml. The yields of caproic acid and butyric acid were 801.94±0.11 mg/100 ml and 1167.33±0.14 mg/100 ml, respectively. The optimized fermentation medium for caproic and butyric acid production consisted of 5.1 g/L peptone, 5.04 g/L sodium acetate, and 4.45 g/L sodium butyrate, with a pH of 6.4. Under these conditions, the production of caproic acid and butyric acid reached 1172.73 mg/100 ml and 2382.45 mg/100 ml, respectively. These values represent significant increases (P<0.05) of approximately 46.24% for caproic acid and 104.09% for butyric acid compared to initial levels. The model predicts caproic and butyric acid production to be 1184.21 mg/100 ml and 2387.84 mg/100 ml, respectively, which closely aligns with experimental results. This indicates the model’s effectiveness and provides valuable insights for enhancing acidity in liquor production.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

This study explores the integration of computer vision with topology optimization for additive manufacturing, with a focus on maximizing eigenfrequency in a design domain. Utilizing cus-tom-developed photogrammetry software, high-resolution images are processed to generate de-tailed 3D models, subsequently converted to STL files with precision. Adaptive meshing in COMSOL Multiphysics, controlled through a MATLAB API, ensures optimal mesh resolution. Prioritizing resource conservation in extraterrestrial environments, the original volume is reduced by 50% while preserving structural integrity. The design domain undergoes rigorous topology optimization in MATLAB, supported by COMSOL's advanced FEM simulation. The optimized design exhibits a 57% performance improvement and a 50% weight reduction, maintaining desired vibration characteristics, validating the efficacy of the modifications. Moreover, the case with an eccentric mass shows a significant 64% increase in eigenfrequency.

This work presents the results of optimizing the physicochemical properties of composite briquettes based on microsilica for metallurgical-grade silicon production. Microsilica, a waste product of silicon production, contains a sufficiently high amount of silicon dioxide (96-97%). This fact makes microsilica a promising composite material for metallurgical processing. However, its granulometric composition limits its direct use. The method of briquetting on an industrial briquetting press was used. The influence of the granulometric composition of the composite mixture on the heat tolerance and strength of the finished briquettes was studied. The methods of obtaining and testing the briquettes, their composition, and the briquetting and drying process are described. The obtained briquettes were tested for the smelting of metallurgical silicon. The silicon recovery rate in the metal with the standard charge was 71%, while the recovery rate with the briquetted monocharge was 85%. The results of silicon smelting from the briquettes demonstrated the high quality of the obtained metal, corresponding to the standards of metallurgical-grade silicon. The implementation of these technologies not only improves the quality of the final product but also addresses environmental issues related to the disposal of microsilica, reducing its accumulation and minimizing its impact on the environment.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

Surface defect detection based on machine vision and convolutional neural networks (CNNs) is an important and necessary process that enables rubber ring manufacturers to improve production quality and efficiency. However, such automatic detection always consumes substantial computer resources to guarantee detection accuracy. To solve this problem, in this paper, we present a CNNs optimization algorithm based on the Ghost module. First, we replace the convolutional layer with the Ghost module in CNNs so that feature maps can be generated using cheaper linear operations. Second, we use an optimization method to obtain the best replacement of the Ghost module to achieve a balance between computer resource consumption and detection accuracy. Finally, we use an image preprocessing method that includes inverting colors. We integrated this algorithm into YOLOv5, which we trained on a dataset with 122 images of rubber ring surface defects. Compared with the original network, the network size decreased by 30.5% and the computational cost decreased by 23.1% whereas average precision only decreased by 1.8%. Additionally, the network's training time decreased by 16.1% as a result of preprocessing. These results show that the proposed approach greatly helped practical rubber ring surface defect detection.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

High dimensional datasets are highly likely to have redundant, irrelevant, and noisy features that negatively affect the performance of the classification algorithms. Selecting the most relevant features and reducing the dimensions of datasets by removing the undesired features is a dimensional reduction technique called Feature Selection (FS). In this paper, we propose an FS approach based on the Black Hole Algorithms (BHO) with a mutation technique called MBHO. Generally, BHO contains two major phases. At the exploitation phase, a set of stars are modified based on some rule and according to some objective function, the best star is selected as the black hole which attracts other stars. Furthermore, when a star gets closer to the event horizon, it will be swallowed and a new one will be randomly generated in the search space which thus is the exploration phase. However, randomness may cause the algorithm to fall into the trap of local optima, and to overcome such complications, inversion mutation is used. Furthermore, we modify a widely utilized objective function in most of the proposed works for wrapper feature selection by combining two new terms that are based on the correlation among the selected subset of features and the features and the classification label. We also utilize a transfer function, known as the V2 transfer function, to convert continuous values into discrete ones to enhance search. We assess our approach via extensive evaluation experiments using fourteen benchmark datasets. We benchmark the performance of a wrapper FS approach called Binary Cuckoo Search (BCS), and three filter-based FS approaches (namely Mutual Information Maximisation (MIM), Joint Mutual Information (JMI), and minimum Redundancy Maximum Relevance (mRMR)). Our evaluation has shown that the proposed model is an effective approach for FS, in selecting better features that enhance the performance metrics on the classifiers. Thus, MBHO can be utilized as one alternative to the existing state-of-art-approaches. We release the source codes of our implementation for the community to build on with new methods and datasets.

The paper describes an application of machine learning approach for parameter optimization. The method is demonstrated for the elasto-viscoplastic model with both isotropic and kinematic hardening. It is shown that the proposed method based on long-short term memory networks enabled to obtain reasonable agreement of stress-strain curves for cyclic deformation in low-cycle fatigue regime. The main advantage of the proposed approach over traditional optimization schemes lies in the possibility to get parameters for a new material without the necessity to conduct any further optimizations. As the power and robustness of the developed method was demonstrated on the very challenging problem (cyclic deformation, crystal plasticity, self-consistent model, isotropic and kinematic hardening), it is directly applicable to other experiments and models.

We designed a bidirectional reflection distribution function (BRDF) measurement system to research the characteristics of space target materials. This system measures the BRDF data of an aluminum plate and gold foil. A hybrid biogeography-based optimization-firefly (BBO-Firefly) algorithm was proposed to optimize the five-parameter BRDF model. To check the performance of the hybrid BBO-Firefly algorithm, we set up a contrast experiment to optimize the BRDF parameters using the BBO algorithm, Firefly algorithm, and hybrid BBO-Firefly algorithm. The experimental results prove that the hybrid BBO-Firefly algorithm surpasses the BBO algorithm and Firefly algorithm in convergence speed and precision in the same situation and has a better optimization effect. Finally, we substitute the optimization results of the hybrid BPO-Firefly algorithm into the BRDF model to analyze the reflection characteristics of an aluminum plate and gold foil.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.