This article discusses the application of thermal quality control methods for plant tissues. The purpose of the work is to determine the optimal parameters of thermal impact on a spherical-shaped plant control object, ensuring the detection of surface and subsurface defects. The authors of the work proposed mathematical models of the temperature field for a spherical body with defects and a flat sample when exposed to the thermal influence of a pulsed source. As a result of the use of mathematical models, the thermophysical characteristics of plant tissues of varying degrees of disease damage were obtained, which made it possible to simulate the temperature field of the control object and obtain an image of classified tissues. The developed recommendations made it possible to select the optimal parameters of the thermal effect on the test object.

Hydrodynamic modeling and hazard mapping are essential tools for urban flood mitigation and spatial planning. Leveraging software like HEC-RAS (Hydrologic Engineering Center - River Analysis System) and ArcGIS, this study aimed to map flood-prone areas along the Jijia River in the Ungheni administrative unit of Iasi County. Human-induced environmental changes and global climate shifts have heightened flood risks worldwide, particularly in urbanized areas. Hydrological and hydraulic modeling anticipate and assess flood events, while hydrodynamic modeling accurately simulates flow propagation, in-forming flood extent, timing, and volume. Flood hazard maps offer essential insights into flooded areas, water depths, and velocities, assisting in risk assessment and mitigation strategies. Through the use of different scenarios, river modeling aims to accurately replicate real-world conditions. This study focuses on Ungheni commune in Iasi County, Romania, situated along the Prut River's eastern bank. Utilizing a combination of fixed-grid and irregular mesh elements in modeling al-lows for fine-tuning of flow details and optimization of simulation times. Model accuracy, particularly regarding peak river levels, hinges on hydrograph duration. While a 30-minute error is typically accepted, greater tolerances may apply to river basins with longer response times. The extraction and processing of model results, including maximum water depths, flood extents, and velocity maps, are facilitated by ArcGIS, providing valuable data for effective flood management strategies.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

The authors previously found a model of universal quantum computation by making use of the coset structure of subgroups of a free group $G$ with relations. A valid subgroup $H$ of index $d$ in $G$ leads to a \lq magic' state $\left|\psi\right\rangle$ in $d$-dimensional Hilbert space that encodes a minimal informationally complete quantum measurement (or MIC), possibly carrying a finite \lq contextual' geometry. In the present work, we choose $G$ as the fundamental group $\pi_1(V)$ of an exotic $4$-manifold $V$, more precisely a \lq small exotic' (space-time) $R^4$ (that is homeomorphic and isometric, but not diffeomorphic to the Euclidean $\mathbb{R}^4$). Our selected example, due to to S. Akbulut and R.~E. Gompf, has two remarkable properties: (a) it shows the occurence of standard contextual geometries such as the Fano plane (at index $7$), Mermin's pentagram (at index $10$), the two-qubit commutation picture $GQ(2,2)$ (at index $15$) as well as the combinatorial Grassmannian Gr$(2,8)$ (at index $28$) , (b) it allows the interpretation of MICs measurements as arising from such exotic (space-time) $R^4$'s. Our new picture relating a topological quantum computing and exotic space-time is also intended to become an approach of \lq quantum gravity'.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

The aim of this work is to analyze and investigate the shape preserving properties of ternary 4-point non-stationary interpolating subdivision schemes constructed by Beccari et al. [1] with a tension parameter !k+1 which can reproducing exponential. Moreover, the conditions on the initial control points are developed that allow user to generate shape preserving limit curves after a nite number of subdivision steps and generalize these results in limiting case. Signicance of derived conditions are illustrated through graphs and the whole discussion is followed by examples.

.Bacground: Sepsis remains a major health challenge worldwide, characterized by a dysre-gulated host response to infection, leading to high mortality and morbidity in intensive care units (ICUs). The Fibrosis 4 (FIB-4) index, originally developed to assess liver fibrosis in hepatitis C patients, has recently been explored for its potential prognostic value in sepsis patients. Method: This study retrospectively analyzed 309 sepsis patients admitted to the Internal Me-dicine and Anaesthesia ICUs between December 12, 2021, and December 15, 2023, to inves-tigate the relationship between FIB-4 levels, Acute Physiology and Chronic Health Evaluation (APACHE), and Sequential Organ Failure Assessment (SOFA) and clinical outcomes. Results: The study found that higher FIB-4 measurements were statistically significantly asso-ciated with increased 28-day mortality, with a cut-off value of 4.9 providing a sensitivity of 54.92% and specificity of 74.25%. Logistic regression analysis indicated that elevated Conclusion:FIB-4 levels were a significant predictor of early mortality, suggesting that the FIB-4 index could serve as a valuable prognostic tool in assessing the severity and prognosis of sepsis patients.

Introduction: The association of gene variants for interleukin 6(IL-6) (rs1800796), interleukin 10 (IL-10) (rs1800896) and tumor necrosis factorα (TNFα (rs1800629) with the occurrence of spontaneous preterm birth (PTB) was investigated to determine whether these genetic variants are a risk factor. Materials and methods: 199 blood samples from pregnant women who had given birth prematurely and 200 control blood samples were analyzed to determine single nucleotide polymor-phisms (SNPs) of genes for IL-6 (rs1800796), IL-10 (rs1800896) and TNFα (rs1800629). The control samples were samples from pregnant women with term delivery. Isolation of DNA was per-formed on mini-spin columns according to the manufacturer's protocol. The quality and purity of the isolated DNA were tested using a Qubit 3 fluorometer. Genotyping was performed with an ABI PRISM 7500 SDS using TaqMan SNP genotyping assays. The genotypes obtained were an-alyzed using the 7500 Software v2.3 package. Results: Carriers of the A/A genotype for the rs1800629 of the TNFα gene have 4.81 times greater chance of late-onset PTB compared to carriers of the G/G and A/G genotypes in the recessive inheritance model. The presence of the G/G genotype in the recessive inheritance model compared with the G/A and A/A genotypes for the rs1800896 of the IL-10 gene represents a potentially protective factor, with mothers in the term-birth group having an almost 2-fold lower odds of PTB in general and an almost 10-fold lower odds of early PTB. On the other hand, carriers of the A/G genotype of rs1800896 have a 1.54-fold higher chance of preterm birth in general and a 1.6-fold higher chance of late preterm birth in the super dominant inheritance model compared to the A/A and G/G genotypes in the group of mothers with PTB. In this study, no association was found between PTB and rs1800796 of the IL-6 gene. Conclusion: rs1800629 in mothers was associated with PTB. rs1800896 shows a potentially protective effect for the occurrence of PTB in this study. No association was found between PTB and rs1800796.

We propose a new theory beyond the standard model of elementary-particle physics. Employing the concept of a quantized spacetime, our theory demonstrates that the zero-point energy of the vacuum alone is sufficient to create all the fields, including gravity, the static electromagnetic field, and the weak and strong interactions. No serious undetermined parameters are assumed. Furthermore, the relations between the forces at the quantum-mechanics level is made clear. Using these relations, we quantize Einstein’s gravitational equation: Beginning with the zero-point energy of the vacuum, and after quantizing Newtonian gravity equation, we combine the energies of a static electromagnetic field and gravity in a quantum spacetime. Applying these results to the Einstein gravity equation, we substitute the energy density derived from the zero-point energy in addition to redefining differentials in a quantized spacetime. This is how we derive the quantized Einstein gravitational equation without assuming the existence of macroscopic masses. For the weak interaction, by considering plane-wave electron and the zero-point energy, we obtain a wavefunction that represents a β collapse. In this process, from a different point of view than Weinberg-Salam theory, we derive the masses of the W and Z bosons and the neutrino, and we calculate the radius and lifetime of the neutron. For the strong interaction, we previously reported an analytical theory for calculating the mass of a proton by providing a specific linear attractive potential obtained from the zero-point energy, which agrees well with the measurements. In the present study, we further calculate the strong interaction between two nucleons, i.e., the mass of the pi-meson. The resulting calculated quantities agree with the measurements, which verifies our proposed theory.

Conventional MRI sequences are standard methods to monitor patients with brain tumors but have significant limitations especially after irradiation. Currently, the role of FET-PET in radiotherapy of glioblastoma is emerging, starting from target definition, response assessment and in distinguishing progression from post-irradiation changes. Recently a PET RANO criteria have been published providing optimal strategy for treatment evaluation with amino-acid PET. Earlier, a PET/RANO group reported contribution of PET imaging to radiotherapy planning and monitoring in glioma patients. Also, increasing evidence have showed advantages of amino-acid PET vs. RANO MRI for prediction of overall survival. In this narrative review we aimed to summarize published data on FET-PET based treatment response assessment to radiotherapy and focused on details in protocols.

We construct a Bayesian estimator for the dilution of a wastewater sample. When wastewater is diluted by rainwater an estimate of the level of dilution is required if we are to normalise sample measurements of disease markers such as SARS-CoV-2 RNA. We consider the situation where flow measurements are available, but will regularly be unreliable because of the action of combined sewer outflows (CSOs) and wastewater storage tanks, which divert wastewater away from treatment plants when the flow is excessive. However, we also have proxies for the flow from various chemical markers (e.g.\ phosphate, ammonium, electrical conductivity), whose level per unit of population is fixed. The new flow estimator has multiple advantages compared to existing procedures: credible intervals for the estimates; optimal weighting of the chemical markers; systematic handling of missing and censored values; and model based smoothing without lags.

Dark pigmentation can be observed in various parts of the plant, ranging from foliage to petals to berries. The molecular basis of black pigmentation appears to vary among species, with anthocyanins playing a significant role, although specific anthocyanin types and their mechanisms differ. These findings suggest that the development of phenotypes is species-specific or varies between larger taxonomic groups; this is further supported by the polyphyletic nature of dark pigmentation. Additionally, several different regulatory mechanisms have been described for the occurrence of dark pigmentation. Firstly, the repression or knockout of the competing flavone biosynthesis has been shown to lead to darker pigmentation while another mechanism is based on the activation and upregulation of the anthocyanin biosynthesis genes in the presence of MYB transcription factors. Potential ecological functions of dark pigmentation were identified as the protection of the photosynthesis apparatus, camouflage against herbivores, and the attraction of pollinators. Promising industrial applications include microbial factories for the production of natural food colourants, induction of novel phenotypes for the ornamental plant industry and lastly the increase of anthocyanins within agriculturally relevant crops.

Exoskeleton technology has been shown to be useful for individuals with spinal cord injury (SCI), potentially facilitating their recovery of motor function and social reintegration. However, studies on the safety and usability of exoskeletons are limited. This study aimed to design a powered exoskeleton for SCI and evaluate its safety and usability. Ten healthy adults participated in this study. The prototype exoskeleton featured an adjustable frame, computer-controlled hip and knee joint actuators, and a gait-trigger sensor. The experimental actions included walking, standing, and sitting, with and without the prototype. Safety outcomes included adverse events, vital signs, numerical rating scale (NRS) scores for pain, discomfort, and fatigue, and prototype-human body clearance. Usability outcomes included donning and doffing times, subjective ratings, gait speed, stride length, and kinematic parameters of hip and knee joint angles. Safety outcomes showed no serious adverse events, stable vital signs, minimal NRS scores, and acceptable clearance. Usability outcomes showed high efficiency and received positive ratings. Kinematic parameters showed significant positive correlations between normal walking and walking with the prototype for both hip and knee joint angles, confirming its effectiveness in assisting walking. However, further device improvements and gait parameter tuning are necessary for future clinical application.

A Cu₂ZnSnS₄ (CZTS) film with a thickness of approximately 1.5 μm was fabricated on a Mo-coated glass substrate by annealing a CZTS precursor fabricated from nanoparticle ink. The chemical states of the elements in the CZTS thin film in the depth direction were studied to identify the presence of secondary phases, which are detrimental to the performance of solar cells containing CZTS. X-ray diffraction was unable to detect any secondary phases in CZTS because of their small relative amount. Instead, X-ray photoelectron spectroscopy (XPS), which is highly sensitive to chemical state, was conducted at different depths in the CZTS film to further check the presence of secondary phases. XPS analysis revealed peaks shift consistent with the presence of secondary phases. For the CZTS film annealed in a S atmosphere at 575 °C for 3 h, the film surface consisted of a secondary-phase layer composed of CuS, ZnS, and SnSx (x=1 or 2) originating from the decomposition of CZTS. At depths below 80 nm, the film was pure CZTS. Formation of MoS2 at the CZTS–Mo interface was confirmed by XPS analysis of Mo and S.

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic and it represents a pollutant of global concern. Liquid Hg is highly volatile and it can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paints, plasters, roof tiles, concretes, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into 7 units) covers a surface of about 65 ha and contains mining structures and managers and workers buildings. In this work, nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in the units 2, 3 and 6. Moreover, detailed measurements were performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in terms of space and time mostly depending on the distance from the building hosting driers, furnaces and condensers and ambient temperature, respectively. In the Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng m⁻³, while in the Unit 6 they were on average much higher and occasionally they saturated the GEM measurement device (>50,000 ng m⁻³). Concentrations of total (in mg kg⁻¹) and leached (in μg L⁻¹) mercury measured in different building materials (up to 46,580 mg kg⁻¹ and 4,470 mg L⁻¹ for total and leached mercury, respectively) showed for the same type of material highly variable values in dependence on the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for the operational cleanings to be carried out during the reclamation activities.

Multiple valued logic (MVL) has proven to be a better alternative and solution to the challenges of traditional binary logic because of its fast computation, fewer interconnects, and small die. It is a potential candidate for future digital design because it allows energy-efficient, low-complex, and high-speed circuits. This paper introduces a new resistive-load two-dimensional field effect transistor-based ternary logic gates, wherein the active resistive-load is replaced with memristor to reduce chip area and power consumption. A memristor-based standard ternary inverter (STI) is designed using GNRFET, MoS2 FET, WSe2 FET, and FinFET, and their performance metric such as delay, power, and energy delay product (EDP) are analyzed. The results show that the proposed design achieves 50% reduction in circuit area, the average power dissipation is reduced by 11.7X, 6.8X, and 3.2X for GNRFET, MoS2 FET, and WSe2 FET, respectively, as compared to FinFET-based ternary inverter. Moreso, other logic gates such as OR, NOR, AND and NAND were simulated in T-SPICE EDA tool, and the results and truth table are in good agreement.

Detection of virus in sample is an actual problem in biotechnology, virology, medicine using biosensor. History of problem dates back to middle of last century and is associated with development of an ion-sensitive solid-state device for neurophysiological measurements. Aim of work is theoretical investigation process of detection antibody+antigen (AB+AG) complexes using SOI-FET biosensor. On example of crystal with ten biosensors, estimates of probability detection AB+AG complexes influenza virus are made. In detection process, following four results are possible: – target complex is present in test sample, and it was correctly detected; – target complex is present in sample, but it was not detected; – target complex is absent in sample, but background particles are mistakenly detected as target complex; – target complex is absent in sample, background particles present in sample and are correctly detected as noise.

46 patients with a newly diagnosed, histologically verified glioma that was visually classified as [18F]FET-negative were included. Tumor volumes were defined using routine T2/FLAIR MRI data and applied to extract information from dynamic [18F]FET PET data, i.e. early and late tu-mor-to-background (TBR5-15, TBR20-40) images and time-to-peak (TTP) images. Radiomic features of healthy background were calculated from the tumor volume-of-interest mirrored to the con-tralateral hemisphere. Differences between tumor and healthy tissue features were compared us-ing Wilcoxon test. Additionally, the ability to distinguish tumor from healthy tissue was assessed using logistic regression. 5 % of features derived from TBR20-40 images were significantly differ-ent; 16 % of features derived from TBR5-15 images and 69 % of features derived from TTP images. The high number of significantly different features derived from TTP images was even found in isometabolic gliomas (after exclusion of photopenic gliomas) with visually normal [18F]FET up-take in static images. However, the differences did not reach satisfactory predictability for ma-chine learning based identification of tumor tissue. In conclusion, radiomic features derived from dynamic [18F]FET PET data may extract additional information even in [18F]FET-negative glio-mas, which should be investigated in larger cohorts and correlated with histological and out-come features in future studies.

The treatment of the bulky Rind-based dibromosilanes, (Rind)2SiBr2 (2) [Rind = 1,1,7,7-tetra-R1-3,3,5,5-tetra-R2-s-hydrindacen-4-yl: EMind (a: R1 = Et, R2 = Me) and Eind (b: R1 = R2 = Et)], with two equivalents of tBuLi in Et2O at low temperatures resulted in the formation of blue solutions derived from the diarylsilylenes, (Rind)2Si: (3). Upon warming the solutions above −20 °C, the blue color gradually faded, accompanying the decomposition of 3 and yielding the cyclic hydrosilanes (4) via intramolecular C−H bond insertion at the Si(II) center. The molecular structures of the bulky Eind-based 3b and 4b were confirmed by X-ray crystallography. Thus, at −20 °C, blue crystals were formed (Crystal-A), which were identified as mixed crystals of 3b and 4b. Additionally, colorless crystals of 4b as a singular component were isolated (Crystal-B), whose structure was also determined by an X-ray diffraction analysis. Although the isolation of 3 was difficult due to their thermally-labile nature, their structural characteristics and electronic properties were discussed based on the experimental findings complemented by computational results. We also examined the hydrolysis of 3b to afford the silanol, (Eind)2SiH(OH) (5b).

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

The prevalence of hepatitis B and delta viruses (HBV/HDV) among people who use drugs (PWUD) remains largely unknown. In the context of one Philadelphia-based harm reduction organization (HRO), this study aimed to assess HBV/HDV prevalence and facilitate linkage to care. Participants completed a demographic HBV/HDV risk factor survey and were screened for HBV and reflexively for HDV if positive for HBV surface antigen or isolated core antibody. Fisher’s exact tests and regression were used to understand relationships between risks and HBV blood markers. Of the 498 participants, 126 (25.3%) were susceptible to HBV, 52.6% had been vaccinated against HBV, and 17.9% had recovered from a past infection. Eleven (2.2%) participants tested positive for isolated HBV core antibody, 10 (2.0%) for HBV surface antigen, and one (0.2%) for HDV antibody. History of incarceration was associated with current HBV infection, while transactional sex and experience of homelessness were predictive of previous exposure. This study found high rates of current and past HBV infection, and a 10% HBV/HDV co-infection rate. Despite availability of vaccine, one quarter of participants remained vulnerable to infection. Findings demonstrate the need to improve low-threshold HBV/HDV screening, vaccination, and linkage to care among PWUD. The study also identified gaps in the HBV/HDV care cascade, including lack of point-of-care diagnostics and lack of support for HROs to provide HBV services.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

Transition-metal-free synthesis of 4-pyrones via TfOH-promoted nucleophilic addition/cyclization of diynones and water has been developed. This transformation is simple, atom economical and environmentally benign, providing rapid and efficient access to substituted 4-pyrones.

Diabetes mellitus (DM) poses a significant challenge to global health, with its prevalence projected to rise dramatically by 2045. This narrative review explores the bidirectional relationship between periodontitis (PD) and type 1 diabetes mellitus (T1DM), focusing on cellular and molecular mechanisms derived by the interplay between oral microbiota and the host immune response. A comprehensive search of literature published between 2008 and 2023 was conducted to elucidate the association between these two diseases. Preclinical and clinical evidence suggests a bidirectional relationship, with individuals with T1DM exhibiting heightened susceptibility to periodontitis, and vice versa. The review includes recent findings from human clinical studies, revealing variations in oral microbiota composition in T1DM patients, including increases in certain pathogenic species such as Porphyromonas gingivalis, Prevotella intermedia, and Aggregatibacter actinomycetemcomitans, along with shifts in microbial diversity and abundance. Molecular mechanisms underlying this association involve oxidative stress and dysregulated host immune responses, mediated by inflammatory cytokines such as IL-6, IL-8, and MMPs. Furthermore, disruptions in bone turnover markers, such as RANKL and OPG, contribute to periodontal complications in T1DM patients. While preventive measures to manage periodontal complications in T1DM patients may improve overall health outcomes, further research is needed to understand the intricate interactions between oral microbiota, host response, periodontal disease, and systemic health in this population.

In recent years, graphene has received so much attention because of its superlative properties and its potential to revolutionize electronics especially in VLSI. This study analyzes the effect of single event upset (SEU) in SRAM cell which employs metal-oxide semiconductor type graphene nano-ribbon field effect transistor (MOS-GNRFET) and compares the results respectively with another SRAM cell designed in PTM 10nm FinFET node. Our simulation show there is a change in data stored in the SRAM after heavy ion strike. However, it recovers from radiation effects after 0.46 ns for GNRFET and 0.51 ns for FinFET. Since the degradation observed in Q and Qb of GNRFET SRAM are 2.7X and 2.16X as compared to PTM nano-MOSFET, we can conclude that GNRFET is less robust to single effect upset. In addition, the stability of SRAM can be improved by increasing the supply voltage VDD.

Modification of electrode surface with a selective layer gives the possibility to detect target ana-lytes of forensic interest. 3-(4-trifluoromethyl)-phenyl)-thiophene (ThPhCF3) was deposited on a graphite (G) electrode by electrochemical oxidation and characterized as a receptor for the recognition of synthetic stimulants (2-aminoindane, buphedrone, naphyrone). First, the structural characterization of the polymeric layer were obtained from Raman spectroscopy. Second, the electrochemical profiles of selected synthetic stimulants and their affinity to ThPhCF3/G-modified electrodes were studied using square wave voltammetry and electrochemical impedance spec-troscopy. The values of the adsorption constant show the importance of – PhCF3 groups in the interaction with synthetic stimulants, namely recognition by the formation of hydrogen bonds (Kads (buphedrone) < Kads (2-AI)) and interaction with aromatic H atoms (Kads (buphedrone) < Kads (naphyrone)). It was demonstrated that the polymeric layer derived from thiophene with – PhCF3 group is capable to increase the intensity of the electrochemical signal.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

In this paper the one-to-one correspondences and equivalences between ideals, primals, filters and grills are introduced. It is shown the local functions and the topological spaces induced by them are the same. From this point of view, the topological properties with respect to one topology can be derived from topological properties valid in the corresponding topology.

To address the issue of reduced orbit estimation accuracy resulting from discrepancies between in-orbit measured geomagnetic field values and IGRF model values in autonomous orbit estimation of microsatellites based on geomagnetic field measurements, this study introduces an adaptive cubature H-infinity filtering algorithm. Firstly, it presents the low-altitude orbital dynamics model and geomagnetic field measurement model for microsatellites. Subsequently, within the adaptive cubature H-infinity filtering algorithm, a spherical simplex rule and a second-order Gaussian-Legendre quadrature criterion are employed to compute the spherical surface integral and radial integral. Additionally, a spherical simplex-radial quadrature rule is proposed to enhance the approximation accuracy of nonlinear Gaussian weighted integrals. Furthermore, by integrating extended H-infinity filtering based on game theory with the cubature quadrature rule, an inverse proportional relationship between constraint level and filtering innovation is established. This allows for adaptive adjustment of the constraint level to enhance robustness against model errors. Finally, through semi-physical simulation experiments, it is demonstrated that compared with traditional algorithms, the proposed algorithm improves autonomous orbit estimation position accuracy of microsatellites by 7.49%, while also enhancing velocity accuracy by 3.1%, thus validating its effectiveness.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Poultry farming in Slovakia has a tradition and an irreplaceable position to ensure rational nutrition for the population. In terms of a nutritional value, poultrymeat (Galliformes) contains a high amount of proteins, essential amino acids, essential unsaturated fatty acids, minerals, vitamins and a low fat content. Poultrymeat production has a relatively short reproductive cycle and thus allows regulating the demand and supply. The poultry market also influences the development of domestic consumption. According to the Statistical Office of the Slovak Republic, the consumption of meat has witnessed a persistent increase over the last 10 years. [1] According to the 2023 AVEC (The Voice of European Meat Sector) annual report, the consumption of poultrymeat in Slovakia was 20.0 kg per person per year. The average consumption in the EU-27 (2021) was 23.4 kg, with the countries with the highest consumption being Portugal (37.8 kg), Ireland (36.0 kg), Hungary (33.5 kg) and Spain (29.9 kg). On the other hand, the countries with the lowest consumption of poultrymeat, apart from Slovakia, also include Austria and Greece with a consumption of 21.5, resp. 21.0 kg [2]. The breeding of broiler chickens, as well as the production and placing on the market of poultrymeat must comply with the requirements laid down by legislation, while the compliance is regularly checked by the competent authorities.

PVC items are environmentally friendly as, unlike polyolefins, they are mainly based on chlorine, one of the most abundant elements on earth. However, in the eco-design context, articles' durability plays the crucial role, contributing to the enhancement of their sustainability. In this framework the research on additives capable of increasing the weatherability of outdoor articles is essential. The theory section of the paper reviews the mechanisms of weathering leading to PVC degradation that undermine the durability of items such as window frames or roller shutters. The weathering of PVC items is a complex phenomenon involving photo-chemical and secondary chemical reactions, that yields the formation of conjugated polyene sequences underskin in absence of oxygen and carbonyls in the surface. Here the chain scission of the polymer backbone occurs, bringing the disintegration of the surface of the item and causing the typical discoloration called chalking, especially evident in dark-colored articles. In the experimental section of the paper the effect of different acid scavengers on the item weathering has been studied with natural outdoor and two accelerated exposures, xenon-arc and Q-UV testing devices. Results confirm that some acid scavengers are efficient in preventing chalking, but some are ineffective or even detrimental. Thus, the PVC formulations of durable articles upon weathering still depend on a complex choice of the appropriate ingredients, and several outdoor and indoor accelerated weathering tests are needed to predict the articles' lifetime.

Nowadays, animal breeders look for effective innovations to care animal health. Use of probiotics, postbiotics, parabiotics and the other beneficial natural substances are dominated. Mundticin-like substance EM 41/3 is thermo-stable bacteriocin (postbiotic) with a broad antimicrobial spectrum. In this study its effect in broiler rabbits was assessed. Rabbits represent food-derived animal and they are also suitable animal model. The parameters tested were analyzed by validated methods. Administration of MLS EM 41/3 produced by non-autochthonous strain Enterococcus mundtii EM 41/3 lead to significant increase of parameter immunity-phagocytic activity, while it did not influence microbiota composition. It also did not influence blood biochemistry and no oxidative stress was noted. Moreover, higher growth parameters were noted and also stimulated hydrolytic activity. Finally, no negative influence on rabbit meat quality was noted. Postbiotic MLS EM 41/3 administration in feeding strategy seems to be contributing fact for rabbit health status maintaining.

Graphene-based Field-Effect Transistors (FETs) integrated with microstrip patch antennas offer a promising approach for Terahertz signal radiation. In this study, a dual-stage simulation methodology is employed to comprehensively investigate the device’s performance. The initial stage, executed in MATLAB, delves into charge transport dynamics within a FET under asymmetric boundary conditions, employing hydrodynamic equations for electron transport in the graphene channel. Electromagnetic field interactions are modeled via Finite-Difference Time-Domain (FDTD) techniques. The second stage, conducted in COMSOL Multiphysics, focuses on the microstrip patch antenna’s radiative characteristics. Notably, analysis of the S11 curve reveals minimal reflections at the FET’s resonant frequency of 1.34672 THz, indicating efficient impedance matching. Examination of the radiation pattern demonstrates the antenna’s favorable directional properties. This research underscores the potential of graphene-based FETs for Terahertz applications, offering tunable impedance matching and high radiation efficiency for future Terahertz devices.

This study proposes an innovative pharmacovigilance approach, VIGI-4, leveraging ChatGPT Teams Pro version. Our method involves aggregating data from all phase 4 studies published in February 2024 to identify adverse reactions. These results are categorized by disease state alphabetically, demonstrating the method's capacity to generate structured and easily navigable outputs. The results section is tailored to exemplify the valuable, actionable insights attainable through our workflow. This research emphasizes the game-changing potential of integrating advanced technologies such as ChatGPT into pharmacovigilance, signaling a new era in safeguarding drug safety.

This paper presents the PEnsemble 4 model, a sophisticated machine learning framework that integrates IoT-based environmental data to accurately forecast maize yield. With the projected significant growth in global maize demand over the next decade, the inherent risks posed by the crop’s dependence on weather conditions necessitate improved prediction capabilities. The PEnsemble 4 model, developed with high accuracy, incorporates comprehensive datasets encompassing soil attributes, nutrient composition, weather conditions, and UAV-captured vegetation imagery. By employing a combination of Huber and M estimates, the PEnsemble 4 model effectively analyzes temporal patterns in vegetation indices, specifically CIre and NDRE, which serve as reliable indicators of canopy density and plant height. In addition, this research significantly contributes to precision agriculture by offering an efficient and sustainable alternative to conventional farming practices through precise yield predictions. Notably, the PEnsemble 4 model enables earlier estimation, advancing the timeline for yield prediction from the conventional day 100 in the R6 stage to day 79 in the R2 stage. This improvement enhances decision-making processes in farming operations. The remarkable accuracy rate of 91% underscores the importance of adopting a multifaceted data approach that harnesses IoT-derived environmental insights. Additionally, the PEnsemble 4 model extends its benefits beyond yield prediction, facilitating the detection of water and crop stress, as well as disease monitoring in broader agricultural contexts. Ultimately, the PEnsemble 4 model establishes a new standard in maize yield prediction, revolutionizing crop management and protection through the synergistic utilization of IoT and machine learning technologies.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

4-(2-Methyloxazol-4-yl)benzenesulfonamide was synthesized by the reaction of 4-(2-bromoacetyl)benzenesulfonamide with an excess of acetamide. The obtained compound was evaluated as a potential inhibitor of human monoamine oxidase (MAO) A and B and was found to inhibit these enzymes with IC50 values of 3.47 μM for MAO-B and 43.3 μM for MAO-A. Thus, the new selective MAO-B inhibitor was identified, which may be used as the lead compound for development anti-Parkinson’s disease agents.

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

The research of object classification and part segmentation is a hot topic in computer vision. A considerable number of studies have been carried out about deep learning on 3D point clouds. However,it is challenging to achieve effective feature learning due to sparsity of point clouds. Recently, a variety of Transformers have been adopted to improve point cloud processing and display great potential. Nevertheless, large numbers of Transformer layers tend to incur huge computational and memory costs. PointNet++ is one of the most influential neural architectures for point cloud understanding. Although the accuracy of PointNet++ has been largely surpassed by recent networks, this does not mean that PointNet++ has no potential.Thus, this paper offer two major contributions that significantly improve PointNet++ performance. Firstly, we introduce a novel contextual feature extraction (CFE) block that significantly enhances the feature extraction capabilities of PointNet++ networks. Secondly, to further enhance feature fusion, we seamlessly integrate a mutual learning (ML) block into the network architecture. By embedding these two innovative blocks within each layer of the network, we not only enrich the network's functionality but also impart it with greater robustness and adaptability. The specific experiments were conducted on the S3DIS (6-fold cross-validation) and Modelnet40 datasets with 86.5% and 92.7% accuracy, respectively, which proved that our model is comparable or even better than most existing methods for classification and segmentation tasks.

Background: This study focuses on different manual handling methods and their effect on psychomotor skills concerning physical measurements (height, weight, age) and pinch strength. Objective: To assess the effects of three manual handling techniques on psychomotor skills and to establish the prediction of pinch strength by physical measurements. Methods: Three manual handling methods were tested: handling with a 90-degree elbow angle, handling with one hand, and handling with both hands. Psychomotor skills were quantified through handgrip strength, dexterity tests, and perceived exertion scales. Linear and random forest regression models were used to predict pinch strength from physical measurements. Results: Handling with a 90-degree elbow angle significantly increased perceived exertion and error rates while decreasing post-task handgrip strength. The one-hand method showed the least negative effect on psychomotor abilities. Weight emerged as the most influential predictor of pinch strength, followed by height and age. The random forest regression model outperformed the linear regression model, indicating its suitability for capturing complex non-linear relationships among variables. The Random Forest Regression model excelled in predicting weight with a high R² score of 0.78, showing strong predictive power. It was moderately effective for height with an R² score of 0.42. However, it performed poorly for age prediction, with an R² score of 0.01, indicating ineffective features for predicting age. Conclusion: The results emphasize the importance of ergonomic interventions and training programs to optimize manual handling practices, aiming to reduce physical strain and enhance worker productivity and safety. Maintaining muscle strength is crucial in older age groups due to the decline in pinch strength with age. These findings can inform intervention studies and the modification of occupational health and safety practices. Future research should aim to validate these results across diverse populations and explore additional factors influencing handgrip strength.

External hoof characteristics, balance, and conformation have been extensively studied in horses; however, mules remain understudied in these aspects. This study evaluated the size, shape, and symmetry of untrimmed and unshod forelimb hooves, compared the symmetry between forelimb hooves and stratified external forelimb hoof measurements based on the body condition score of mules raised in the foothill plains of northern Thailand. The forelimb hooves of 38 mules were photographed and 33 parameters, including angular and linear measurements, were analyzed. Despite the absence of shoeing and trimming, these mules exhibited optimal left-right forelimb hoof symmetry, with no significant (p < 0.05) differences in: outer wall length and inner wall length (OWL - IWL); sole length and sole width (SLS - SW); dorsal hoof wall length and heel length (DHWL - HL); and frog length and frog width (FL - FW). However, significant (p < 0.05) differences were observed within each body condition score group for forelimb hoof measurements for DHWL, IWL, heel separation (HS), heel bulb distance (HBD), SW, FW, and FL. These findings provide valuable insights into mule welfare and management, contributing to understanding of the interplay between overall health and hoof conformation in the study area.

Antibiotic prescription is the first line of treating bacterial diseases. But it affects the composition and function of non-targeted intestinal microbiota. Antimicrobial resistance will be the cause for the death of millions of people worldwide. By considering collateral damage of antibiotics, searching an alternative antimicrobial agent will be a solution to minimize the problems. Probiotics, prebiotics and synbiotics are an alternative to antibiotics. Thanks to GIT microbes as they are responsible for metabolism, energy production, protection from pathogens and immunomodulation. So, it is appreciable if the gut microbiota modulated through consumption of probiotics, prebiotics and synbiotics. Probiotic effects are genus and species specific. To get good health benefit of probiotics, safety of probiotics should be assessed before using them. This is mandatory for prebiotics and synbiotic selection. So this review paper gives information about side effects of antibiotics on gut microbiota, description of probiotics, prebiotics and synbiotics as alternative to antibiotics in modulating GIT microbiota, techniques of assessing safety of probiotics and health benefits of probiotics, prebiotics and synbiotics with scientific evidence in clinical trial and some disagreement and challenges of using probiotics, prebiotics and synbiotics.

Temporomandibular disorders (TMDs) refer to a group of conditions that affect the temporomandibular joint, causing pain and dysfunction in the jaw joint and related muscles. The diagnosis of TMDs typically involved clinical assessment through operator-based physical examination, self-reported questionnaire and imaging studies. To objectivize the measurement of TMD, this study aims at investigating on the feasibility to use machine-learning algorithms fed with data gathered from low-cost and portable instruments to discriminate the presence of TMD in adult subjects. Through this aim, the experimental protocol involved fifty participants, equally distributed between TMD and healthy subjects, acting as control group. The diagnosis of TMD has been performed by a skilled operator through the typical clinical scale. Participants underwent to a baropodometric analysis by using a pressure matrix and the evaluation of the cervical mobility through inertial sensors. Nine machine-learning algorithms belonging to support vector machine, k-nearest neighbours and decision tree were compared. The k-nearest neighbours based on cosine distance was found as the best performing, achieving performance of 0.94, 0.94 and 0.08 for the accuracy, F1-score and G-index, respectively. These findings open the possibility to use such methodology to support the diagnosis of TMDs in clinical environments.

Background: Ventilator-associated pneumonia (VAP) is among the most common healthcare-associated infections in Pediatric Intensive Care Units (PICUs). Because of the lack of a gold-standard diagnostic test, early diagnosis of VAP is challenging. We investigated whether bronchial biomarkers interleukin-4 (IL-4), plasminogen activator inhibitor-1 (PAI-1) and soluble receptor for advanced glycation end products (RAGE) could contribute in early VAP diagnosis through their fluctuation in time in critically ill pediatric patients. Methods: Bronchial secretions were collected from PICU patients with VAP on days 1 and 6. PAI-1, RAGE and IL-4 levels were measured by ELISA. Protein concentrations between high and low VAP suspicion patients were compared using unpaired Student’s t or Mann–Whitney U tests. Results: Twenty PICU patients, with median age 7.75yrs (range 0.5-15.3), mechanically ventilated for ≥48hrs with increased oxygenation requirements and VAP clinical/laboratory signs were enrolled. They were divided in VAP high-suspicion (n=12) or low-suspicion (n=8) groups based on Clinical Pulmonary Infection Score (cutoff:6). ΡΑΙ-1 και RAGE levels did not differ between high- or low-VAP suspicion groups the 1st or 6th days (p-value&gt;0.05). IL-4 was not detected in bronchial secretions. Conclusion: Bronchial concentrations of IL-4, PAI-1 and RAGE in critically ill children are not correlated with high- or low-VAP suspicion.

We define a spinor-Minkowski metric for SL(4,C). It is not a trivial generalization of the SL(2,C) metric and it involves the Minkowskian one. We define 4x4 version of the Pauli matrices and eight 4-component associated generalized eigenvectors that can be regarded as undotted covariant spinors. The 4-component spinors can be grouped into four categories. Each category transforms in its own way. The outer products of pairwise combinations of 4-component spinors can be associated with 4-vectors. Including the dotted covariant, undotted and dotted contravariant forms totally we have sixteen pairs of spinors. Eight of them live in the conjugate space which has no countepart in SL(2,C).

Introduction The monitoring of cerebral perfusion in patients with brain damage is a major clinical challenge. Monitoring cerebral oxygenation (rSO2) by NIRS was introduced at the turn of the 1980s, and many clinicians believed it was a valuable method for assessing cerebral perfusion and subsequent measures to optimize cerebral flow. The main problem of NIRS usage is the presence of the intermediate structures-skin, skull, meninges, cerebrospinal fluid-and their influence on the outcome of the test. Therefore, it seems that NIRS assessment performed on a patient during brain death attempts, can give an idea of the magnitude of the influence of these intermediate structures on the monitoring result. Case We present a retrospective analysis of cerebral oxygenation measurements of a patient undergoing a brain death diagnostic procedure. A clinical situation where the cerebral blood flow is stopped can give an idea of the specificity of the method, particularly the impact of the influence of intermediate structures on the monitoring outcome. In this case, the NIRS result is increased by the oxygenation of the patient before the apnoea test. The influence of chromophores in the tissues surrounding the CNS, reflections and scattering of the light wave spectrum have a very significant effect on the final result of cerebral saturation measurement. Discussion The majority of research observations describing changes in cerebral perfusion or its optimisation may be burdened by the problem described, i.e. the significant influence of measured oxygenation from intermediate structures. The specificity of NIRS to assess cerebral perfusion requires careful analysis. The therapeutic implications of monitoring cerebral oxygenation with NIRS are of great importance and, from the example presented and the literature provided, the method should be used with caution. It has been shown that in a patient with brain death, the result of NIRS oxygenation measurements depends on the surrounding structures of the brain.

Biomaterials are the basis for the development of medicine because they allow safe contact with a living organism. The aim of this work was to produce innovative oxide layers with a porous microstructure on the surface of commercially pure titanium Grade 4 (CpTi G4), and to characterize their properties as drug carriers. Anodization of the CpTi G4 subjected to mechanical grinding and electrochemical polishing was carried out in a solution of 1M ethylene glycol with the addition of 40 g of ammonium fluoride at a voltage of 20 V for 2, 18, 24 and 48 hours at room temperature. It was found that the longer anodization time, the greater the number of pores formed on the CpTi G4 surface as revealed by FE-SEM method, and the greater the surface roughness determined in profilometric tests. As the anodizing time increases, the amount of the drug in the form of gentamicin sulfate incorporated into the resulting pores decreases. The most favorable drug release kinetics profile determined by UV-VIS absorption spectroscopy was found for the CpTi G4 anodized for 2 h making them the best choice when it comes to the drug carrier allowing full use of the therapeutic dose of the drug.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Herein, two title compounds, N-Benzoyl-N’-4-cyanophenyl thiourea (I) and N-(4-nitrobenzoyl)-N’-4-cyanophenyl thiourea (II) were synthesized in high yield, via aroyl isocyanate and 4-aminobenzonitrile. The structure of the prepared compounds was characterized by elementary analysis and FT-IR, ¹H, ¹³C NMR spectroscopic methods. Cyclic voltammetric (CV) experiments were performed with glassy carbon electrode. The reduction potential values of different functional group such as nitro, cyano in title compounds were investigated using CV curves.

Hydrological processes are complex to compute on hilly areas when compared to the plain areas. Most of the hydrological model do not take into account the critical rainfall-runoff generation processes such as subsurface storm flow, saturation excess flow, overland flow, return flow and pipe storage. The simulations of the above processes in the soil matrix requires detailed hillslope hydrological modelling. In present study, a hillslope experimental plot is designed to study the runoff generation processes on the plot scale. The setup is designed keeping in view the natural hillslope conditions prevailing in the north western Himalayas, India where high intensity storm event occurs frequently. Using the experimental data and the developed conceptual model, the overland flow and the subsurface flow through macropore dominated area has been estimated/analyzed on the pixel basis. Over the experimental hillslope plot, a rainfall simulator was installed to generate the rainfall intensity in the range of 15 to 150 mm/hr which represented the dominating rainfall intensity range in the region. Soil moisture sensors were also installed at 100 mm and 300 mm depth at different locations of the plot to observe soil moisture variations. It was found that once the soil is saturated, it remains in the field capacity for next 24-36 hours. Such antecedent moisture conditions are most favorable for the generation of rapid stormflow from hillslopes. Dye infiltration test was also performed on the undisturbed soil column to observe the macropore fraction variability over the vegetated hillslopes. The surface runoff predicted using the developed hillslope hydrological model compared well with the observed surface runoff under high intensity rainfall conditions.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

Reverse engineering is applied to identify optimum polymerization conditions for the synthesis of polymer with pre-defined properties. The proposed approach uses multi-objective optimization (MOO) and provides multiple candidate polymerization procedures to reach the targeted polymer property. The objectives for optimization include maximal similarity of molar mass distributions (MMD) compared to the target MMD, minimal reaction time, and maximal monomer conversion. The method is tested for vinyl acetate radical polymerizations and can be adopted to other monomers. The data for the optimization procedure is generated by an in-house developed kinetic Monte-Carlo (kMC) simulator for a selected recipe search space. The proposed reverse engineering algorithm comprises several steps: kMC simulations for the selected recipe search space to derive initial data, performing MOO for a targeted MMD, and identification of the Pareto optimal space. The last step uses a weighted sum optimization function to calculate the weighted score of each candidate polymerization conditions. To decrease the execution time clustering of the search space based on MMDs is applied. The performance of the proposed approach was tested for various target MMDs. The suggested MOO-based reverse engineering provides multiple recipe candidates depending on competing objectives.

Abiotic stress is responsible for significant reduction in crop plant productivity worldwide. Ultraviolet (UV) radiation is a natural component of sunlight and a permanent environmental stimulus. This study investigated the distinct responses of young wheat and einkorn plants to excessive UV-B radiation (180 min at λmax 312 nm) following foliar pretreatment with 1 µM synthetic cytokinin 4PU-30. Results demonstrated that UV radiation significantly amplified hydrogen peroxide levels in both wheat and einkorn, with einkorn exhibiting more pronounced increase compared to wheat. This elevation indicated the induction of oxidative stress by UV radiation in the two genotypes. Intensified antioxidant enzyme activities and increased accumulation of typical stress markers and non-enzyme protectants were evidenced. Transcriptional activity of genes encoding key antioxidant enzymes was also investigated aiming to elucidate the genetic regulation of the antioxidant systems in both wheat and einkorn seedlings. Our results suggested a role for POX1 and POX7 genes in the UV-B tolerance of the two wheat species as well as a cytokinin stimulated UV-B stress response in einkorn mediated through upregulation of the tau subfamily gene GSTU6. Based on these findings it could be concluded that 4PU-30 had the potential of alleviating oxidative stress by attenuating the symptoms of superfluous UV-B illumination in the two examined plant species.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

An oxidation resistant coating on cemented tungsten carbides is characterised in this work. Cemented tungsten carbides (cWCs) are routinely used in mining and manufacturing but are also candidate materials for compact radiation shielding in fusion power generation. In both environments, cWCs will suffer significant degradation due to oxidation at relatively low temperatures. In a recent study, a Si-deposition coating method was demonstrated to improve the oxidation resistance of cWCs by up to a factor of 1,000. This work focusses on the growth kinetics, phase composition, and mechanical properties of these coatings. By combining quantitative X-ray diffraction, electron microscopy and nanoindentation, we show that the coating layer has a 20 % higher hardness than the substrate, which was explained on the basis of a previously-unknown presence of a fine distribution of very hard SiC laths. To interpret the coating stability, a coating growth map is developed. The map shows the structure is stable under a broad range of processing temperatures and composite compositions, demonstrating the potential application of these coatings in a variety of nuclear shielding cWCs.

Molecular-scale density fluctuations at equilibrium produce cavities in a liquid and can be analyzed to shed light on the statistics of the number of molecules occupying observation volumes of increasing radius. An information theory approach led to the conclusion that these probabilities should follow a Gaussian distribution function. This prediction has been confirmed by computer simulations in different liquid models if the size of the observation volume is not large. The reversible work of cavity creation is exactly linked to the probability of finding zero molecules in a given observation volume. The Gaussian formula for the latter probability is scrutinized to arrive at the enthalpy and entropy changes associated with cavity creation. The reversible work of cavity creation has a purely entropic origin due to the solvent-excluded volume effect produced by the inaccessibility of a given region of the configurational space. The consequent structural reorganization of liquid molecules leads to exactly compensating enthalpy and entropy changes. These results are in line with those obtained in a direct statistical mechanical study by Lee.

Treatment of the non-purified mixture of dinitro isomers obtained from the nitration of 1,4-dimethoxybenzene with piperidine, led to the isolation of novel but minor adduct, 1-(2,5-dimethoxy-4-nitrophenyl)piperidine (2b) in 15% yield. Yields of nucleophilic aromatic substitution adducts are high when using purified 1,4-dimethoxy-2,5-dinitrobenzene (1b) with piperidine and pyrrolidine to give 2b and 1-(2,5-dimethoxy-4-nitrophenyl)pyrrolidine (3b) in 76% and 82%, respectively.

The 5-hydroxymethylfurfural (HMF) is a six-carbon heterocyclic organic compound with two substituents an aldehyde group and an alcohol group. It is formed from saccharides as a result of two reactions: the Maillard reaction and the caramelization of saccharides. It has both a negative and a positive effect on the human body, which makes it, even more, an attractive research object. The objective of the study was to determine HMF content in honey samples available on the Polish market using three varied methods and compare the results obtained. The methodology used included: two spectrophotometric methods (by White and Winkler) and the HMF determination method based on the LC-MS/MS technique developed uniquely for this study. The determined HMF content in all tested honey samples did not exceed the applicable standard. All results are within the scope of the European Council Directive 2001/110/EC of 20 December 2001, i.e. they do not exceed HMF content in honey, which is 40 mg/kg.

The increasing emergence of multidrug resistant (MDR) pathogens causes difficult-to-treat infections, with long-term hospitalizations and high incidence of death, thus representing a global public health problem. To manage MDR bacteria bugs, new antimicrobial strategies are necessary, and their introduction in practice is a daily challenge for scientists in the field. An extensively studied approach to treat MDR infections consists in inducing high levels of reactive oxygen species (ROS) by several methods. Although further clinical investigations are mandatory on the possible toxic effects of ROS to mammalian cells, clinical evaluations are extremely promising, and their topical use to treat infected wounds and ulcers, also in presence of biofilm, is already clinically approved. Biochar (BC) is a carbonaceous material obtained by pyrolysis of different vegetable and animal biomass feedstocks, at 200−1000 °C in limited presence of O2. Recently, it has been demonstrated that BC capability of removing organic and inorganic xenobiotics is mainly due to the presence of persistent free radicals (PFRs), which can activate oxygen, H2O2 or persulfate in the presence or not of transition metals by electron transfer thus generating ROS, which in turn degrade pollutants by advanced oxidation processes (AOPs). In this context, the antibacterial effects of BC containing PFRs have been demonstrated by some authors against Escherichia coli and Staphylococcus aureus, thus giving birth to our idea of the possible use of BC-derived PFRs as a novel method capable of inducing ROS generation for antimicrobial oxidative therapy. Here, the general aspects concerning ROS physiological and pathological production and regulation, and the mechanism by which they could exert antimicrobial effects have been reviewed. The methods currently adopted to induce ROS production for antimicrobial oxidative therapy have been discussed. Finally, for the first time, BC-related PFRs have been proposed as a new source of ROS for antimicrobial therapy via AOPs.

Background: This study assesses the effects of the ‘Radiant’ image enhancement technique on fetal nuchal translucency (NT) measurements during first trimester sonographic ex-ams. Methods: A retrospective analysis of 263 ultrasound images of first trimester midsagittal sections was conducted. NT measurements were obtained using a semi-automatic tool. Statistical methods were applied to compare NT measurements with and without ‘Radi-ant’ enhancement. An in-vitro setup with predefined line distances provided additional data. Results: Incremental increases in NT measurements were observed with varying levels of ‘Radiant’ application: An average increase of 0.19 mm with ‘Radiant min’, 0.24 mm with ‘Radiant mid’ and 0.30 mm with ‘Radiant max.’ The in-vitro results supported these findings, showing consistent effects on line thickness and measurement accuracy, with the smallest mean deviation occurring at the ‘Radiant mid’ setting. Conclusions: ‘Radiant’ image enhancement leads to significant increases in NT measure-ments. To avoid systematic biases in clinical assessments, it is advisable to disable ‘Radi-ant’ during NT measurement procedures. Further studies are necessary to corroborate these findings and to consider updates to the NT reference tables based on this technology.

Solar radiation is the main energy source for mankind and an accurate data of solar radiation levels for a particular location is vital for the optimum operation of solar energy transducers such as photovoltaic cells and solar thermal collectors. In this work, we show that there is a linear relationship between recorded monthly average temperatures and solar radiation in Swaziland. The correlation can be utilized to develop two mathematical models for the estimation of solar radiation: one from the measured monthly average temperatures and the other based on the square-root of the difference between measured maximum and minimum monthly average temperatures. Both models fit the data well and can be applied to estimate solar radiation in other parts of the region.

The importance of contact with nature for human health was confirmed by numerous research. One of the sometimes neglected fields is the landscape design of hospital premises. This study focuses on the perception and preferences of prospective patients regarding the hospital site design. The methodology included anonymous survey with images and lists of adjectives. The online questionnaire was distributed using e-mails and social media from 4th May to 8th July 2024. The objective was to include all age groups. The results confirm previous studies and demonstrate the importance of landscape architecture design of hospital premises for the well-being of patients. The findings may inform the design of hospital sites.

Paratuberculosis, or Johne's disease, caused by Mycobacterium avium subsp. paratuberculosis (MAP), is a chronic granulomatous enteritis affecting both domestic and wild ruminants. The agent was also found in wild mammals such as wild boar (Sus scrofa), however, the role of wild mammals in the epidemiology of MAP is unclear. During the research period, 941 free-ranging wild boar (S. scrofa) legally hunted in two locations in the Centre-eastern region of Portugal were examined. Ninety-seven wild boar exhibited one or more gross lesions and were tested for the presence of Mycobacterium avium subsp. paratuberculosis using acid-fast staining, mycobacterial culture, poly-merase chain reaction (PCR), and histopathological examination. Forty-five animals (46.4%, 95% CI: 36.5-56.3%) were identified as infected, as indicated by positive results in culture and/or PCR. The findings revealed that the most significant risk factor was being a juvenile compared to year-lings and adults (OR = 10.2, 95% CI: 2.2-48.0). Based on our results, 37.9% (n = 11) of the infected animals were considered suitable for human consumption. Our findings offer novel insights into mycobacterial infections in wild boar populations in Portugal and suggest that wild boar could be a source of human infection if zoonotic potential is considered.

Postprandial glucose levels between 4 and 7.9 hours (PPG4–7.9h) correlate with mortality from various diseases including hypertension, diabetes, cardiovascular disease, and cancer. This study aimed to assess if predicted PPG4–7.9h could diagnose diabetes. Two groups of participants were involved: Group 1 (4420 participants) had actual PPG4–7.9h, while Group 2 (8422 participants) lacked this measure but had all the diabetes diagnostic measures. Group 1 underwent multiple linear regression to predict PPG4–7.9h using 30 predictors, achieving accuracy within 11.1 mg/dL in 80% of the participants. Group 2 had PPG4–7.9h predicted using this model. Receiver operating characteristic curve analysis showed that predicted PPG4–7.9h could diagnose diabetes with an accuracy of 87.3% in Group 2, with a sensitivity of 75.1% and specificity of 84.1% at the optimal cutoff of 102.5 mg/dL. Simulation on 10,000 random samples from Group 2 revealed that 175 participants may be needed to investigate PPG4–7.9h as a diabetes diagnostic marker with a power of at least 80%. In conclusion, predicted PPG4–7.9h appears to be a promising diagnostic indicator for diabetes. Future studies seeking to ascertain its definitive diagnostic value might require a minimum sample size of 175 participants.

A variant of the von Neumann-Wigner Interpretation is proposed. Problems arising from the quantum Zeno effect are addressed as we have described previously. We do, however, offer some new, and perhaps unexpected observations. We are accustomed to thinking of wave function collapse as occurring consequent to laboratory measurements. We speculate that, whatever physical correlate of consciousness exists within the brain, it is quantum mechanical in the sense that a brain, left to itself, would eventually decohere into a state no longer compatible with its conscious functioning. Wave function collapse returns it to a state compatible with consciousness. Indeed, this may be its important reason for occurring. A universe without it simply could not play host to conscious brains. The fact that it also prevents us from encountering "absurd" situations in the laboratory is merely a fortunate dividend. Whenever a quantum measurement is made the universe's future history splits into a number of possibilities. This number may be very large or infinite. And we believe consciousness plays a vital role in this happening. A "conscious" universe where quantum measurements are being made allows for an enormous number of equally acceptable world-histories. An "unconscious" one, always evolving in a unitary fashion, allows for only one. If we assume that the decision as to which worldhistory is the real one (i.e. this one) is made at random we see that the universe is overwhelmingly more likely to be "conscious" than not.

Synergistic effects between reactions, reagents and catalysts can lead to minor heats of reaction and occur as an inherent result of multi-component reactions (MCRs) and their extensions. They enable syntheses to be performed at a low energy level and the number of synthesis steps to be drastically reduced in comparison with ‘classical’ two-component reactions. The very high potential for variability, diversity and complexity of MCRs additionally generates an extremely diverse range of products, thus bringing us closer to the aim of being able to produce tailor-made and extremely low-priced materials, drugs and libraries.

Analysis of liquid biopsy samples can reveal a wealth of molecular as well as cellular entities circulating in various body fluids. These entities include circulating tumor cells, circulating cell-free and tumor DNA, RNA, and proteins. Detection and characterization of this genetic and proteomic material can provide crucial information on tumor characteristics, including its heterogeneity, biology, tumor progression, staging, associated gene mutations and the course of therapy. The increased use of liquid biopsy in clinical oncology offers in non-invasive manner easier tumor sampling and continuous monitoring of the disease evolution through repetitive sampling from cancer patients. The continuous monitoring offered by this method is highly relevant to the assessment of a given therapeutic regime and early detection of markers associated with possible drug resistance, which may develop in the course of the therapy. The use of proteomic approaches, including mass spectrometry-based proteomics for the analysis of biofluids extends for over three decades, yet only in the last few years such methods have found their way to clinical oncology. The non-invasive nature of liquid biopsy and the simple procedures for sample collection made this approach far more attractive than the traditional and well-established tissue biopsy. Such preference becomes more practical in the analysis of solid tumors, particularly in pediatric population. In this review we discuss some works on the emerging role of liquid biopsy analyses in clinical oncology, and how such use allows a better understanding of diagnosis, prognosis, disease evolution and response to therapy of various forms of cancer. We also discuss the role of MS-based methods in the characterization of post-translational modifications of proteins circulating in liquid biopsies.

The reactivity of 3,5-di-(pyridin-4-yl)-1,2,4-thiadiazole (L1) with 1,4-diiodotetrafluorobenzene (1,4-DITFB) was explored and the halogen-bonded 1:1 co-crystal (1) was successfully isolated and structurally characterized.

The study of precipitation amount at different time scales constitutes an important issue in climate research and risk assessment. When dealing with daily totals, a frequent but sometimes underestimated problem is at what time the observation day begins. The choice of different starting times may lead to incompatibility between stations and incorrect identification of extreme events. In this work, the problem of temporal misalignment between precipitation datasets characterized by different starting time of the observation day is analyzed. The most widely used adjustment methods (1day and uniform shift) and two methods based on reanalysis (NOAA and ERA5) are evaluated in terms of temporal alignment, precipitation statistics and percentile distributions. As test series, the precipitation amount collected from 9 a.m. local time (09 LT) on the previous day to 09 LT on the target day (9-9 datasets) of the Padua and nearby stations in the period 1993-2022 have been selected. Results show that the reanalysis-based methods, in particular ERA5, outperform the others in temporal alignment, regardless the station. But, for the periods in which reanalysis data are not available, “1day” method, which shifts the daily amount back one calendar day, and “unif” method, which distributes uniformly the daily total from a 2-day moving window surrounding the target date, can be considered valid alternatives. On the other side, concerning the precipitation statistics, the reanalysis-based methods are not the best option, as they increase the precipitation frequency and reduce the mean value over wet days, NOAA much more than ERA5. Nevertheless, the uniform method provides a larger deviation from the original daily series. The use of the series of a station nearby the target one, which is mandatory in case of missing data, gives similar or better results than applying any adjustment method to the 9-9 series. General conclusions can hardly be drawn as they depend on the method and station. For the Padua dataset, the analysis was repeated at monthly and seasonal resolution. In general, the adjustment series show the most relevant changes in the precipitation statistics in summer and less temporal alignment with the original series in summer and autumn, the two seasons mainly affected by heavy rains in Padua. Finally, the percentiles distribution, analyzed for all the methods and stations, indicates that any adjustment method underestimates the percentile values, except ERA5. Only Legnaro, the station most correlated with Padua, gives results like ERA5.

Accurate classification of objects in 3D point clouds is a significant problem in several applications, such as autonomous navigation and augmented/virtual reality scenarios, which has become a research hot spot. In this paper, we presented a deep learning strategy for 3D object classification in augmented reality. The proposed approach is a combination of the GRU and LSTM. LSTM networks learn longer dependencies well, but due to the number of gates, it takes longer to train; on the other hand, GRU networks have a weaker performance than LSTM, but their training speed is much higher than GRU, which is The speed is due to its fewer gates. The proposed approach used the combination of speed and accuracy of these two networks. The proposed approach achieved an accuracy of 0.99 in the 4,499,0641 points dataset, which includes eight classes (unlabeled, man-made terrain, natural terrain, high vegetation, low vegetation, buildings, hardscape, scanning artifacts, cars). Meanwhile, the traditional machine learning approaches could achieve a maximum accuracy of 0.9489 in the best case.

Hydrogen gas (H2) has attracted attention as a next-generation clean energy source. Its efficient and safe preparation and utilization are crucial in both industry and organic chemistry. In this study, a Pt/CB-catalyzed MW-mediated continuous-flow hydrogenation reaction was developed using methylcyclohexane (MCH) as the reducing agent (hydrogen carrier). Alkynes, alkenes, nitro groups, benzyl esters, and aromatic chlorides were chemoselectively hydrogenated using Pt/CB under MW-assisted continuous-flow conditions. This methodology represents a safe and energy-efficient hydrogenation process, as it eliminates the need for an external hydrogen gas supply or heating jackets as a heat medium. Further application of MW-mediated continuous-flow hydrogenation reactions is a viable method for the efficient generation and utilization of sustainable energy.

This article has been studied the synthesis of a new derivative of the known alkaloid cytisine contained in the seeds of plants of Cytisus laburnum L. and Thermopsis lanceolata R.Br., both of the Lugiminosae family. The new compound has been obtained from two biologically active compounds such as isoxazole and cytisine. It has been demonstrated that the reaction led to the single-stage method under very mild conditions to obtain some 4-[(3,5-dimethyl-1,2-oxazole-4-yl)sulfonyl]amides. This class of compounds is promising to obtain the new biologically active compounds. This article has examined in detail a structure with using the 1H and 13C NMR and two-dimensional NMR spectroscopy of COSY (1H-1H), HMQC (1H-13C) and NMVS (1H-13C). As a result, the homo- and heteronuclear spin-spin couplings should be established. The X-ray diffraction analysis has determined the spatial structure of a new derivative based on cytisine alkaloid. Thus, its hemorheological activity has been studied.

Pueraria mirifica (PM), a plant whose dried and powdered tuberous roots are now widely used in rejuvenating preparations to promote youthfulness in both men and women, may have major estrogenic influence. In this study, we investigated modifying effects of PM at various doses on mammary and endometrial carcinogenesis in female Donryu rats. Firstly, PM administered to ovariectomized animals at doses of 0.03%, 0.3%, and 3% in a phytoestrogen-low diet for 2 weeks caused significant increase in uterus weight. Secondly, a 4 week PM application to non-operated rats at a dose of 3% after 7,12-dimethylbenz[a]anthracene (DMBA) initiation resulted in significant elevation of cell proliferation in the mammary glands. In a third experiment, postpubertal administration of 0.3% (200 mg/kg body weight (b.w.)/day) PM to 5-week-old non-operated animals for 36 weeks following initiation of mammary and endometrial carcinogenesis with DMBA and N-ethyl-N′-nitro-N-nitrosoguanidine (ENNG), respectively, resulted in significant increase of mammary adenocarcinoma incidence. A significant increase of endometrial atypical hyperplasia multiplicity was also observed. Furthermore, PM at doses of 0.3% and, more pronouncedly, of 1% induced dilatation, hemorrhage and inflammation of the uterine wall. In conclusion, postpubertal long-term PM administration to Donryu rats exerts estrogenic effects in the mammary gland and uterus, and at a dose of 200 mg/kg b.w./day was found to promote mammary carcinogenesis initiated by DMBA.

The comparison of three types of ionosonde data from Europe during an Interplanetary Coronal Mass Ejection (ICME) and a Stream Interaction Regions (SIRs) / Corotating Interaction Regions (CIRs) -driven geomagnetic storm event is detailed in this study. The selected events are 16-20 March 2015 for the ICME-driven and 30 May to 04 June 2013 for the SIR/CIR-driven one. Ionospheric data from three European ionosonde stations, namely Pruhonice (PQ), Sopron (SO) and Rome (RO), are investigated. The ionospheric F2-layer responses to these geomagnetic events are analyzed with the ionospheric foF2 and h’F2 parameter, the calculated deltafoF2 and deltahF2 values, ratio of Total Electron Content (rTEC) and Thermosphere, Ionosphere, Mesosphere, Energetics and Dynamics (TIMED) satellite Global Ultraviolet Imager (GUVI) thermospheric [O]/[N2] measurement data. The storm-time and the quiet day mean values are also compared, and it can be concluded that the quiet day curves are similar at all stations while the storm-time ones showed the latitudinal dependence during the development of the storm. As a result of the electron density comparison, during the two events it can be concluded that SSC that characterized the ICME induced a Travelling Atmospheric Disturbance (TAD) seen in the European stations, while this is not in the SIR/CIR-driven ionospheric storm, which showed a stronger and more prolonged negative effect in all stations probably due to the season.

New dimers of selected dipyridothiazines with an m-xylene linker have been designed, synthesized and characterized. Their structure was identified using 1H and 13C NMR as well as 2D NMR techniques (COSY, ROESY, HSQC and HMBC experiments) and HR MS spectrometry. The compounds were subjected to preliminary in silico biological profile tests using the Way2Drug server and analysis of the probable cytotoxic effect on various cancer cell lines. Preliminary in vitro cytotoxicity tests were performed against normal cell lines (HaCaT) and five cancer cell lines (SW480, SW620, MDA-MB-231, A-549, LN-229) showing moderate activity. An analysis of the structure-activity relationship was performed.

Background: Histone deacetylases (HDACs) are implicated in carcinogenesis, and HDAC inhibitors (HDACis) are explored as a therapeutic tool in several tumors. The aim of this study was to evaluate the clinical significance of HDAC -2, -4, and -5 expression in epithelial ovarian carcinoma (EOC). Methods: HDAC-2, -4, and -5 immunohistochemical expression was examined in 92 EOC tissue specimens and was correlated with clinicopathological characteristics. Results: HDAC-2 was the most frequently (94.4%) expressed isoform, being marginally higher in serous tumors compared with other types (p=0,08). HDAC-5 was the less frequently expressed (28.1%), being positively associated with HDAC-4. HDAC-4 positivity was associated with lower FIGO-stage (p=0,045) and T-category (p=0.,043) and the absence of lymph node (p=0,05) or distant metastasis (p=0,09) in serous carcinomas. HDAC-2 positivity was correlated with absence of lymph node metastasis in serous tumors (p=0,045). On the contrary, HDAC-5 nuclear positivity was correlated with lymph node metastasis in the entire cohort (p=0,048). HDAC-4 positivity was marginally associated with favorable prognosis in serous carcinomas in univariate survival analysis (p=0,086), a correlation which was not significant in multivariate analysis. Conclusion: These findings suggest a differential expression of HDAC-2, -4 and -5, providing evidence for a potential role in the pathobiology of EOC.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.

The cooling of server components has been continuously developed over the past few years in order to meet the increasing cooling requirements of server component manufacturers such as for the processor chips. The growth in performance and power density increases the cooling demand. These requirements directly influence the energy consumption and performance of the hardware. To gain a better understanding of the historical evolution and possible future technology development paths in the field of data center cooling, a patent analysis method was used. The focus is on previous and current development priorities and possible research gaps within the server and computer room levels. The European patent database was selected as data source. To determine relevant patents, the search terms for various cooling technologies were developed iteratively. After the patent extraction for the period 2000 - 2023 (earliest priority year), the search results were classified and analysed. Most of the patents deal with air or liquid cooling. In the area of liquid cooling, the focus was on direct liquid cooling, followed by total liquid cooling. Since 2015 a technological shift from air to liquid cooling can be identified on the level of patent activities. In this context, the patent groups with focus on “constructional details for different types of electric apparatus” and “electrical digital data processing” have the largest share of patents. In addition, the technology focus of the TOP 10 patent applicants was in the field of liquid cooling. In conclusion from the patent analysis, it can be derived that liquid cooling will continue to gain in importance in the future and could also be combined with other approaches in the form of hybrid cooling. However air cooling may still be relevant, even if the main cooling load is handled by liquid-based approaches. At the same time, the optimisation potential for air cooling seems to have been largely exploited in comparison to liquid cooling, as can be seen from the falling number of the patent applications.

The point cloud is a form of three-dimensional data that comprises various detailed features at multiple scales. Due to this characteristic and its irregularity, point cloud analysis based on deep learning is challenging. While previous works utilize the sampling-grouping operation of PointNet++ for feature description and then explore geometry by means of sophisticated feature extractors or deep networks, such operations fail to describe multi-scale features effectively. Additionally, these techniques have led to performance saturation. And it is difficult for standard MLPs to directly "mine" point cloud. To address above problems, we propose the Detail Activation (DA) module, which encodes data based on Fourier transform after sampling and grouping. We activate the channels at different frequency levels from low to high in the DA module to gradually recover finer point cloud details. As training progresses, the proposed Point-MDA can uncover local and global geometries of point cloud progressively. Our experiments show that Point-MDA achieves superior classification accuracy, outperforming PointNet++ by 3.3% and 7.9% in terms of overall accuracy on the ModelNet40 and ScanObjectNN dataset, respectively. Furthermore, it accomplishes this without employing complicated operations, while exploring the full potential of PointNet++.

A software defined radio (SDR) is a communication system that makes use of components that can be configured through software, in contrast to traditional systems where these components are variable through hardware, these radio devices are much more versatile, this article describes the factors that must be considered when implementing a communication system based on Software Defined Radios (SDR), in order to reduce the attenuation factors and thus obtain the maximum distance for a transmission of data effectively in the UHF band. The calculations made for the first Fresnel zone and for the design of the Ground Plane type antennas used in the transmission/reception stages of the x40 bladeRF platforms are also presented. The tests were carried out at the facilities of the Huarangal Nuclear Center of the Peruvian Institute of Nuclear Energy, obtaining favorable results that allow ratifying the versatility and performance of the SDRs.

1) We shall discuss what modern interpretations say about the Heisenberg's uncertainties. These interpretations explain that a quantity begins to 'lose' meaning when a conjugate property begins to 'acquire' definite meaning. We know that a quantity losing meaning means that it has no fixed value and has an uncertainty . In this paper we look deeper into this interpretation and the outcome reveals more evidence of the quantity losing meaning. Newer insights appear. 2) We consider two extreme cases of hypothetical processes nature undergoes, without interference by a measurement: One, a system collapses to an energy eigenstate under the influence of a Hamiltonian instantaneously at a time $t$. This is thus what would happen if we would measure the system's energy. Next, when a particle becomes localised to a point at a time $t_0$ under the influence of a Hamiltonian. This is thus what would happen if we would measure the system's position. We shall prove that both these situations cannot arise under ordinary circumstances and thus measurement processes cannot be modelled by physical Hamiltonians.

Access to medical care is a global issue. Technology-aided approaches have been applied in addressing this. Interventions have however not focused on medical diagnosis as a fully automated procedure and available applications employ mainly text-based inputs rather than conversation in natural language. We explored the utility of ontology-based chatbot technology for the design of intelligent agents for medical diagnosis through a systematic review of the most recent related literature. English articles published in 2011-2016 returned 233 hits which yielded 11 relevant articles after a 3-stage screening. Findings showed that the creation of expert systems had been the focus of many the studies which utilize the physician-system-patient framework with system training based mostly on expert knowledge for designing web- or mobile phone-based applications that serve assistive purposes. Findings further indicated gaps in the design and evaluation of more effective systems deployable as standalone applications, for example, on an embodied robotic system. The need for technology supporting the physical examination part of diagnosis, connection to data sources on patients’ vitals and medical history are also indicated in addition to the need for more qualitative work on natural language-based interaction. The system should be one that is continuously learning. Future works should also be directed towards the building of more robust knowledge base as well as evaluation of theory-based diagnostic methodological options

Digital filtering is a fundamental technique in digital signal processing, which operates on a digital sequence without any information on how the sequence was generated. This paper proposes a methodology for designing the equivalent of digital filtering for neuromorphic samples, which are a low power alternative to conventional digital samples. In the literature, filtering using neuromorphic samples is done by filtering the reconstructed analog signal, which is required to belong to a predefined input space. We show that this requirement is not necessary, and introduce a new method for computing the neuromorphic samples of the filter output directly from the input samples, backed by theoretical guarantees. We show numerically we can achieve a similar accuracy compared to the conventional method. However, given that we bypass the analog signal reconstruction step, our results show significantly reduced computation time for the proposed method and good performance even when signal recovery is not possible.

The purpose of this work is to determine the possibility of using an automated SkyWatcher Virtuoso system to analyze distribution of sky luminance. The article presents the procedure for measuring the sky luminance distribution defined according to CIE using a manual luminance meter cooperating with the SkyWatcher system. The use of matrix luminance meter was also analyzed.

Unmanned Aerial Vehicles (UAVs) are now filling in the gaps between spaceborne and ground-based observations and enhancing the spatial resolution and temporal coverage of data acquisition. In the realm of hydrological observations, UAVs have a key role to quantitatively characterize the surface flow allowing for remotely accessing the water body of interest. In this paper we propose a technology which uses a sensing platform encompassing a drone and a camera to determine the water level. The images acquired my means of the sensing platform are then analyzed using the Canny method to detect the edges of water level and of Ground Control Points (GCPs) used as reference points. The water level is then retrieved from images and compared to a benchmark value obtained by a traditional device. The method is tested at four locations in an artificial lake in central Italy. Results are encouraging as the overall mean error between estimated and true water level values is around 0.02 m. This technology is well suited to improve hydraulic modeling and thus provide a reliable support to flood mitigation strategies also in uneasy-to-access environments.

Migraine is a neurovascular disorder that can be debilitating for individuals and society. Current research focuses on finding effective analgesics and management strategies for migraines by targeting specific receptors and neuropeptides. Nevertheless, the responder rates of recently approved calcitonin gene-related peptide (CGRP) monoclonal antibodies (mAbs) and receptor inhibitors remain around 50 percent. To address the need for novel therapeutic targets, researchers are exploring the potential of another secretin family peptide, pituitary adenylate cyclase-activating polypeptide (PACAP), as a ground-breaking treatment avenue for migraine. Preclinical models have revealed how PACAP affects the trigeminal system, which is implicated in headache disorders. Clinical studies have demonstrated the significance of PACAP in migraine pathophysiology; however, a few clinical trials remain inconclusive: the pituitary adenylate cyclase-activating peptide 1 receptor mAb, AMG 301 showed no benefit for migraine prevention, while the PACAP ligand mAb, Lu AG09222 significantly reduced the number of monthly migraine days over placebo in a phase 2 clinical trial. Meanwhile, another secretin family peptide vasoactive intestinal peptide (VIP) is gaining interest as a potential new target. In light of recent advances in PACAP research, we emphasize the potential of PACAP as a promising target for migraine treatment, highlighting the significance of exploring PACAP as a member of the antimigraine armamentarium, especially for patients who do not respond to or contraindicated to anti-CGRP therapies. By updating our knowledge on PACAP and its unique contribution to migraine pathophysiology, we can pave the way for reinforcing PACAP and other secretin peptides, including VIP, as a novel treatment option for migraines.

Migraine and neuropathic pain (NP) are evocative of painful, disabling, chronic conditions which exhibit resembling symptoms and thus considered to share a common etiology. Calcitonin gene-related peptide (CGRP) has gained credit as a target for migraine management; nevertheless, the efficacy and the applicability of CGRP modifiers warrant search for more effective therapeutic targets for pain management. This scoping review overviews human studies of common pathogenic factors in migraine and NP to explore potential novel therapeutic targets. CGRP causes inflammation in the meninges; monoclonal antibodies and inhibitors target CGRP. Gluta-mate-induced hyperexcitability and subsequent sensitization are closely linked to an alteration of the tryptophan (Trp)-kynurenine (KYN) metabolic system; the Trp-KYN system may serve as a potential target. Microglial overaction is observed in migraine and NP; modifying the microglial activity may be a possible approach. Cytokine-induced inflammation is a leading hypothesis of the pathogenesis of the conditions; alleviating neuroinflammation may complement a pain-relieving armamentarium. Transient receptor potential (TRP) ion channels evoke the release of several substances; TRP ion channels may potentially emerge as new targets. The endocannabinoid system plays a major role in the pain trafficking pathway; modification of the system may open a new path toward discovery of new analgesics. Here we highlight the mechanism of those common pathogenic factors to explore therapeutic targets for innovative pain management in migraine and NP.

Nearly half a century has passed since the discovery of cytoplasmic inheritance of human chloramphenicol resistance. The inheritance was then revealed to take place maternally by mitochondrial DNA (mtDNA). Later, a number of mutations in mtDNA were identified as a cause of severe inheritable metabolic diseases with neurological manifestation, and the impairment of mitochondrial functions has been probed in the pathogenesis of a wide range of illnesses including neurodegenerative diseases. Recently growing number of preclinical studies has revealed that animal behaviors are influenced by the impairment of mitochondrial functions and possibly by the loss of mitochondrial stress resilience. Indeed, as high as 54% of patients with one of the most common primary mitochondrial diseases, mitochondrial encephalomyopathy with lactic acidosis and stroke-like episodes (MELAS) syndrome, present psychiatric symptoms including cognitive impairment, mood disorder, anxiety, and psychosis. Mitochondria are multifunctional organelles which produce cellular energy and play a major role in other cellular functions including homeostasis, cellular signaling, and gene expression, among other. Mitochondrial functions are observed to be compromised and to become less resilient under continuous stress. Meanwhile, stress and inflammation have been linked to the activation of the tryptophan (Trp)-kynurenine (KYN) metabolic system, which observably contributes to development of pathological conditions including neurological and psychiatric disorders. This narrative review discusses the functions of mitochondria and the Trp-KYN system, the interaction of the Trp-KYN system with mitochondria, and the current understanding of the involvement of mitochondria and the Trp-KYN system in preclinical and clinical studies of major neurological and psychiatric diseases.

A simple approach was developed to predict corn yields using the MoDerate Resolution Imaging Spectroradiometer (MODIS) data product from two geographically separate major corn crop production regions: Illinois, USA and Heilongjiang, China. The MOD09A1 data product, which are 8-day interval surface reflectance data, were obtained from day of the year (DOY) 89 to 337 to calculate the leaf area index (LAI). The sum of the LAI from early in the season to a given date in the season [end of DOY (EOD)] was well fitted to a logistic function and represented seasonal changes in leaf area duration (LAD). A simple phenology model was derived to estimate the dates of emergence and maturity using the logistic function parameters b1 and b2, which represented the rate of increase in LAI and the date of maximum LAI, respectively. The phenology model predicted emergence and maturity dates fairly well, with root mean square error (RMSE) values of 6.3 and 4.9 days for the validation dataset, respectively. Two simple linear regression models (YP and YF) were established using LAD as the variable to predict corn yield; the yield model (YP) used LAD from predicted emergence to maturity, and the yield model (YF) used LAD for a predetermined period from DOY 89 to a particular EOD. When state/province corn yields for the validation dataset were predicted at DOY 321, near completion of the corn harvest, the YP model performed much better than the YF model, with RMSE values of 0.68 t/ha and 0.66 t/ha for Illinois and Heilongjiang, respectively. The YP model showed a similar or better performance, even for the much earlier yield prediction at DOY 257, compared to that of the YF model. In conclusion, the phenology and yield models were developed based only on logistic changes in remote sensing-derived LAD, and predicted phenological dates and corn yields with considerable accuracy and precision for the two regions selected for this study. However, these models must be examined for spatial portability in more diverse agro-climatic regions.

Using two infectious DNA clones originating from isolates obtained in Kenya, a genetic investigation of maize streak virus (MSV) pathogenicity was carried out. The susceptible Pioneer hybrid 3379 was used to investigate the virulence of kernels administered through vascular puncture inoculation. Mild [pMSV-KL (mild)] and severe [pMSV-Km(severe)] parental infectious MSV DNA clones were linked with considerable changes in the severity of chlorotic streaks and stunting of seedlings. Using restriction endonuclease fragments, chimeric clones were created from parental clones in order to investigate the genetic elements influencing these changes. Restrictions mapping was used to validate clone identities. For genomic portions encoding the replication initiator (Rep and RepA), movement (MP), and coat (CP) protein ORFs as well as for those containing non-coding long (LIR) and short intergenic regions (SIR), putative virulence determinants were discovered. Recombinant clones with intermediate symptoms included LIRs together with the first 189 nt of the Rep/RepA ORFs from the pMSV-Km (Severe) and pMSV-KL (Mild) ORFs. Symptoms identical to those of parental clones were produced by complementary substitution of the Rep/RepA ORF. When compared to pMSV-Km (Severe), the recombinant clone having MP, CP, and SIR genome sequences from pMSV-KL(Mild) and LIR, Rep, and RepA genome sequences from pMSV-Km (Severe) displayed much more severe symptoms and accumulated greater concentrations. The reciprocal clone, in contrast, displayed much milder signs and virus titers than pMSV-KL(Mild). The level of leaf chlorosis and plant stunting were linked with viral accumulation. These findings are consistent with the idea that MSV virulence is a polymorphic feature involving complementary sense genes (LIR and SIR) and the virion.