As a new type of high-performance material, gradient structural steel is widely used in engineering fields due to its unique microstructure and excellent mechanical properties. For the prevalent fatigue failure problem, the rate of change of the local grain size gradients along the structure (referred to as the gradient rate) is a key parameter in the design of gradient structures, which significantly affects the fatigue performance of gradient structural steel. In this work, a method of ‘Voronoi primary + secondary modeling’ is adopted to successfully establish three typical high-strength steel models corresponding to the convex, linear, and concave type gradient rates for gradient structures, focusing on the stress-strain response and crack propagation in structural steel with different gradient rates under cyclic loading. It is found that the concave gradient rate structural model is dominated by finer grains with larger volume fraction, which is conducive to hindering fatigue crack propagation and has the longest fatigue life; the linear structure is the second one, and the convex structure is the shortest one. The simulation results in this work are consistent with the relevant experimental phenomena. Therefore, when regulating the gradient rate, priority should be given to increasing the volume fraction of fine grains and designing a gradient rate structure dominated by fine grains to improve the fatigue life of the material.

AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

While L-PBF offers advantages in terms of geometrical freedom or lightweight construction, its use is often limited by economic constraints or currently achievable part costs. With an anticipated increase of L-PBF machine productivity during the next years, an increase of the share of material costs and the share of non-productive time for powder layer application process is to be expected. This results in a demand for less expensive powder materials and advanced processing strategies for the short-and medium-term advancement of L-PBF. As one possible approach, the processing of gas- and water atomized stainless steel (316L) powders with different morphology and particle size distribution as well as their impact on L-PBF productivity is investigated. The actual powder applicability in L-PBF systems and the L-PBF processability determines the minimum necessary powder quality. The main focus of the presented work is put on the interaction between powder quality, powder layer properties, part quality and cost-effectiveness of the L-PBF process. To this end, the influence of the gas and water-atomized powder properties (particle size and morphology) during the powder layer application process at highest possible powder recoater speeds and the resulting powder bed properties (powder layer density, powder bed density, powder demixing) and part properties (part density and tensile strength) is investigated.

The objective of this study is to determine the relationship between body condition score (BCS) and body carcass fat (BCF) of ewes at two key stages of the production cycle. Data were collected from 88 Coopworth ewes including BCS measurements manually evaluated by the farm manager, BCF measurements determined by computerized tomography (CT) and body parameter measurements automatically determined by an image processing application. Artificial neural network (ANN) statistical analysis method was used to develop a relationship between the body parameters and the BCF with an r2=0.96 and RMSE=1.01 using all top and side variables.

Hydration and fluids detected with bioimpdance can be confounderdby ecw expansion and overload. to estimates with sufficient accuracy body fat A confrontation with imaging and dxa is confirmatory

Obesity is a highly prevalent chronic disease characterized by excessive weight gain and fat accumulation. There is growing evidence that Lactiplantibacillus plantarum strains with bile salt hydrolase (BSH) activity are effective in preventing and alleviating obesity. However, few of them has confirmed the anti-obesity effect of BSH by gene deletion. In this study, 23 BSH-positive Lp. plantarum strains were screened by bile salt precipitation halo assay. Among these strains, Lp. plantarum Lp20 showed the highest BSH activity with a hydrolysis rate to glycodeoxycholic acid (GDCA) by 91.62%. Genomic sequencing and bioinformatics analysis indicated that gene bsh1 was associated with BSH activity of Lp. plantarum Lp20 and gene deletion of bsh1 confirmed the role of Bsh1 in GDCA hydrolysis. To investigate if the Bsh1 from Lp. plantarum Lp20 could alleviate obesity, the wild type and bsh1 deletion mutant strains were administered daily for 8 weeks to diet-induced obese mice, respectively. Compared with mutant strain, the wild type strain Lp20 significantly reduced body weight gain, inguinal white adipose tissue and mesenteric fat mass in obese mice. In addition, Lp20 also reduced serum total cholesterol levels and LDL-C by 20.8% and 33.3%, respectively. Furthermore, the recovered liver steatosis was only observed in Lp. plantarum Lp20 treated mice. Taken together, the bile salt hydrolase Bsh1 from Lp. plantarum Lp20 was a key functional factor on ameliorating HFD-induced obesity by reducing cholesterol levels and suppressing adipogenesis in mice.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Excess consumption of a high-fat diet has been identified as one of the contributing factors for obesity. Women are at higher risk for adult obesity than men, predisposing them to a different set of detrimental disease conditions. Furthermore, aging studies show that physiological decline also has a serious impact on changes in the endocrine properties of white adipose tissue. Howev-er, there is still relatively little known about the factors associated with obesity and aging and their compounding impact on women’s health. To investigate adipocytokine secretion profile changes, female C3H/HeJ mice were induced to obesity through long-term consumption of a high-fat diet. Weight gain measurements and Echo MRI analysis of fat composition showed in-creases were a due solely to the high fat content in the diet. Adipocytokine secretions were ana-lyzed in media conditioned from harvested visceral fat tissue that was organ cultured ex-vivo. Adipocytokine analysis across diets and age showed significant increases in Adiponectin and Leptin secretion in high-fat diets, accelerated increases in Resistin secretion with high-fat diets. Aging induced increased secretion of Lipcalin-2, Pentraxin-3 and Serpin E1, MCP-1 and ICAM-1, regardless of diet. Furthermore, comparisons of organoid cultured protein secretions and flash-frozen tissue samples differed greatly, suggesting the WAT organoid cultures may yield information more reflective of in situ conditions. Taken together, our results show that diet and aging significantly impact secretions from adipose tissue, that may contribute to women’s health issues.

Fused deposition modeling (FDM) is a rather new technology in the production of personalized dosage forms. Melting and printing of polymer–active pharmaceutical ingredient (API) – mixtures can be used to produce oral dosage forms with different dosage as well as release behavior. This process is utilized to increase the bioavailability of pharmaceutically relevant active ingredients that are poorly soluble in physiological medium by transforming them into solid amorphous dispersions (ASD). Release from such ASDs is expected to be faster and higher compared to the raw materials and thus enhance bioavailability. Printing directly from powder while forming ASDs was realized. Different techniques to change release patterns as well as a non-destructive way for determination of API distribution were shown. By measuring the melt viscosities of mixtures printed a rheological model for the printer used is proposed.

Polymeric composites such as Poly-ether-ether-ketone (PEEK)/carbon fiber (CF) have been widely utilized due to outstanding performances such as high specific strength and specific modulus. The PEEK/CF components via powder-bed fusion additive manufacturing usually show brittle fracture behaviors induced by their poor interfacial affinity and inner voids. These defects are strongly associated with powder packing quality upon deposition. The particle dynamic model has been widely employed to study the interactions of particle motions. Powder property, bulk material property, and interfacial features of composite powders are key factors in the particle dynamic model. In this work, an efficient and systematic material evaluation is developed for composite powders to investigate their deposition mechanism. The discrete element method is utilized to simulate the dynamic behaviors of PEEK/CF composite powders. The powder properties, bulk material properties, and interfacial features of powders are calibrated and justified by experimental measurement, numerical simulation, and design of experiments. The particle dynamic model can well explain the powder flow behaviors and interactions. It reveals that the addition of short CF particles can assist the flow of PEEK powders and improve the packing quality of the composite powders.

Succinate is proposed to be a mediator of muscle exercise-induced adaptations. We studied metabolic health and changes of muscle mass in 6-month-old male mice after 12 weeks of feeding regular diet (RD, 13.4 kcal% fat, 66.8 kcal% carbohydrate, 29.8 kcal% protein), high fat diet (HFD, 60 kcal% fat, 20 kcal% carbohydrates, 20 kcal% protein) and ketogenic diet (KD, 80 kcal% fat, <1 kcal% carbohydrates, 20 kcal% protein) with or without 2% succinate supplements (SUS) in drinking water (n=8-12 per group). Functional overloading of the plantaris muscle (PL) was induced in a group of mice by denervation of the gastrocnemius and soleus muscles at week 6 of feeding different diets. HFD induced the greatest (p < 0.001) increase in body and fat mass. HFD and KD lead to significant (p < 0.01) impairment in glucose tolerance compared to RD. SUS blunted (p < 0.01) initial surge in energy intake when mice were switched from RD to HFD, but did not influence any measures of metabolic health after 12 weeks of the study. Functional overloading lead to ~25% increase in PL mass which was not affected by diet or SUS. In conclusion, SUS does not have a long-term effect on metabolic health or muscle mass.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

(1) The purpose of this study was to compare the percentages of quarterly change for each of the variables analysed (height, weight, body fat percentage and muscle mass) as a function of the quarter in a sample of adolescent football players. (2) The sample consisted of young male football players of different categories belonging to a high-performance football academy, (more than 5 years in football and have spent 1 full year at the academy). (3) Two-way repeated measures ANOVA revealed for the anthropometric variable, P_value

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Epoxy powders offer a low-cost means of manufacturing thick section composite parts, such as those found in wind and tidal turbines. Currently, their processing cycle includes a lengthy drying stage (≥ 15 h) to remove ambient moisture. This prevents void defect formation and, thereby, a reduction in mechanical properties, however, it constitutes up to 60% of the processing time. Little research has been published on the study of this process or its optimisation. Experimental and simulated analyses are used to investigate the effects of hygroscopicity in epoxy powder composites. In particular, focus is given to the drying process, which is used to prevent void defect formation and, thereby, a reduction in mechanical properties. As such, tests are performed to quantify the void content of dried and undried laminates, and to measure its impact on transverse flexural strength. Dynamic vapour sorption analysis is used to study the sorption behaviour of the epoxy powder. Sorption data is fitted to a modified linear driving force model, and then implemented in existing process simulations tools. The drying of a thick epoxy powder composite section is simulated to investigate the influence of powder sintering on the duration required for drying. It is shown that the epoxy powder is slightly hygroscopic (1.36 wt%) and exhibits sorption behaviour that is characteristic of glassy polymers. This results in up to 4.8% voids (by volume) if processed in an undried state, leading to a 43% reduction in transverse flexural strength. Process simulations reveal that a standard drying cycle prematurely sinters the powder; inhibiting moisture release. By maintaining a powder state, simulations show that the drying cycle can be reduced to 5 h.

Background: The modified Duke index derived from coronary computed tomography angiography (CCTA) was designed to predict cardiovascular outcomes based on the severity of coronary ste-nosis. However, it does not take into consideration the presence or severity of peri-coronary in-flammation. The peri-coronary fat attenuation index (FAI) is a novel imaging marker determined by CCTA which reflects the degree of inflammation in the coronary tree in patients with coronary artery disease. Purpose: To assess the association between the modified Duke index assessed by CCTA, cardiovascular risk factors and peri-coronary inflammation in the coronary arteries of pa-tients with coronary artery disease. Methods: One hundred seventy-two patients who underwent CCTA for typical angina were assigned into two groups based on the modified Duke index: group 1 – patients with low index ≤ 3 (n=107) and group 2 – patients with high index > 3 (n=65). Demo-graphic, clinical and CCTA data were collected for all patients, and FAI analysis of coronary in-flammation was performed. Results: Patients with increased values of the modified Duke index were significantly older compared to those with a low index (61.83 ± 9.89 vs. 64.78 ± 8.9; p = 0.002). No differences were found between the two groups in terms of gender distribution, hypertension, hypercholesterolemia or smoking history (all p > 0.5). The FAI score was significantly higher in patients from group 2, who presented a significantly higher score of inflammation compared to the patients in group 1, especially at the level of the right coronary artery (FAI score 20.85 ± 15.80 vs. 14.61 ± 16.66; p = 0.01 for the right coronary artery, 13.85 ± 8.04 vs. 10.91 ± 6.5; p = 0.01 for the circumflex artery, and 13.26 ±10.18 vs. 11.37 ± 8.84; p = 0.2 for the left anterior descending artery). CaRi-Heart® analysis identified a significantly higher risk of future events among patients with a high modified Duke index (34.84 % ± 25.86 % versus 16.87 % ± 15.80 %; p

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

This study investigated the effects of fish oil (FO) treatment, particularly enriched with eicosapentaenoic acid (EPA), on obesity induced by a high-fat diet (HFD) in mice. The investigation focused on elucidating the impact of FO on epigenetic modifications in white adipose tissue (WAT) and the involvement of adipose-derived stem cells (ASCs). C57BL/6j mice were submitted to a control diet or a HFD for 16 weeks, treated (or not) with FO for the last 8 weeks. WAT was removed for RNA and protein extraction, while ASCs were isolated, cultured, and treated with Leptin. All samples were analyzed using functional genomics tools, including PCR-array, RT-PCR and Western Blot assays. Mice receiving HFD displayed increased body mass, fat accumulation, and altered gene expression associated with WAT inflammation and dysfunction. FO supplementation attenuated these effects, a potential protective role against HFD-induced obesity. Analysis of H3K27 revealed HFD-induced changes in histone, which were partially reversed by FO treatment. The study further explored leptin signaling in ASCs, suggesting a potential mechanism for ASC dysfunction in the leptin-rich environment of obese WAT. Overall, FO supplementation demonstrated efficacy in mitigating HFD-induced obesity, influencing epigenetic and molecular pathways, and shedding light on the role of ASCs and leptin signaling in WAT dysfunction associated with obesity.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

The concerning worldwide increase of obesity and chronic metabolic diseases such as T2D, dyslipidemia, and cardiovascular disease motivates further investigations into preventive and alternative therapeutic approaches. Over the past decade, there is growing evidence that the formation and activation of thermogenic adipocytes (brown and beige) may serve as therapy to treat obesity and its associated diseases owing to its capacity to increase energy expenditure and to modulate circulating lipids and glucose levels. Thus, understanding the molecular mechanism of brown and beige adipocytes formation and activation will facilitate the development of strategies to combat metabolic disorders. Here, we provide a comprehensive overview of pathways and players involved in the development of brown and beige fat as well as the role of thermogenic adipocytes in energy homeostasis and metabolism. Also, we discuss the alterations in brown and beige adipose tissue function during obesity and, explore the therapeutic potential of thermogenic activation to treat metabolic syndrome.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Background: Bioelectrical impedance (BIA) and ultrasound (US) have become popular for estimating body fat percentage (BF%) due to their low cost and clinical convenience. However, agreement of these devices with gold standard method still require investigation. The aim was to analyze the agreement between a gold standard %BF assessment method with BIA and US devices. Methods: Twenty-three men (age 30.1 ± 7.7 years, 82.5 ± 14.9 kg, 1.77 ± 0.05 m) underwent Dual Energy X-Ray Absorptiometry (DXA), BIA (tetrapolar) and US (three-site method) %BF assessment. Pearson and concordance correlations were analyzed. T-test compared means between methods, and Bland Altman plots analyzed agreement and proportional bias. Alpha was set at < .05. Results: Pearson coefficients between BIA and US with DXA were high (BIA = 0.94; US = 0.89; both p < .001). Concordance coefficient was high for BIA (0.80) and moderate for US (0.49). BF% measured by BIA (24.5 ± 7.5) and US (19.4 ± 7.0) were on average 4.4% and 9.6% lower than DXA (29.0 + 8.5%), respectively (p < .001). Lower and upper agreement limits between DXA and BIA were -1.45 and 10.31, while between DXA and US were 2.01 and 17.14, respectively. There was a tendency of both BIA (p = .09) and US (p = .057) to present proportional bias and underestimate BF%. Conclusions: Despite the correlation, the mean difference between the methods were significant, and the agreement limits are very wide. This indicate that BIA and US, as measured in this study, have limited potential to accurately measure %BF compared to DXA, especially in individuals with higher body fat.

This research has developed a process for producing ZnO thin film from DEZn deposited onto a PET substrate with low-pressure, high-frequency Ar + O2 plasma using a chemical vapor deposition technique. The aim is to study the film production conditions that affect electrical properties, optical properties, and thin film surfaces. This work highlights the use of plasma energy produced from a mixture of gases between Ar + O2. Plasma production is stimulated with an RF power supply to deliver high chemical energy and push ZnO atoms from the cathode inside the reactor onto the substrate through surface chemical reactions. The results showed that increasing the RF power in plasma production affected the chemical reactions on the substrate surface of film formation. The film preparation at RF power 300 W will give the thickest films. The film has a continuous columnar formation, and the surface has a granular structure. This results in the lowest electrical resistivity of 1.8 x 10-4 Ω-cm. In addition, when fabricated into a DSSC device, the device tested the PCE value and showed the highest value at 5.68%. This is due to the very rough surface nature of the ZnO film, which increases the scattering and storage of sunlight, making cells more efficient. Therefore, the benefit of this research is that it will be a highly efficient prototype of thin film production technology using a chemical process that reduces production costs and can be used in the industrial development of solar cells.

Polyelectrolyte-drug complexes are interesting alternatives to improve unfavourable drugs properties. Vancomycin (VAN) is an antimicrobial used in the treatment of methicillin-resistant Staphylococcus aureus pulmonary infections in patients with cystic fibrosis. It is generally administered intravenously with high incidence of adverse side effects, which could be reduced by intrapulmonary administration. Currently, there are no commercially available inhalable formulations containing VAN. Thus, the present work focuses on the preparation and characterization of an ionic complex between hyaluronic acid (HA) and VAN with potential use as inhalable formulations. Particulate-solid HA-VAN25 complex by spray drying from an aqueous dispersion was obtained. FTIR spectroscopy and thermal analysis confirmed the ionic interaction between HA and VAN, while an amorphous diffraction pattern by X-ray was observed. The powder density, geometric size and morphology showed a suitable aerosolization and aerodynamic performance of the powder, indicating the capability of reaching the deep lung. An in vitro extended-release profile of VAN from the complex was obtained, exceeding 24 hours. Microbiological assays against methicillin-resistant and -sensitive reference strains of Staphylococcus aureus, showed that VAN preserves its antibacterial efficacy. In conclusion, HA-VAN25 exhibited interesting properties for the development of inhalable formulations with potential efficacy and safety advantages over conventional treatment.

Insulin signaling plays a crucial role in cellular uptake of glucose and different metabolic pathways. Impairment in cellular insulin sensitivity due to various molecular pathways leads to Insulin resistance (IR) as well as fatty liver. In this review, mechanisms by which zinc involved in decreasing IR are described, focusing on oxidative stress, inflammation, immune system, gut flora and hepatic lipophagy. This study reviews the cause of IR and highlights the role of zinc in mechanisms diminishing IR and fatty liver.

Laser Powder Bed Fusion (LPBF), as a transformative technology in the field of additive manufacturing, offers unprecedented design flexibility and material efficiency. This review paper delves into the latest advancements in LPBF technology and the various alloys used in the process, including titanium alloys, aluminum alloys, nickel-based superalloys, steel alloys, copper alloys, and high-entropy alloys. For each alloy category, we discuss their specific applications, performance characteristics, and challenges faced in LPBF usage. The paper discusses important technological breakthroughs, including innovations in laser systems, scanning strategies, and in-situ monitoring technologies, which have enhanced the precision and reliability of LPBF.

Additive manufacturing (AM) is today’s buzzword—and not only in commercial production. One of the AM techniques produces 3D objects with complex geometry using a laser beam. The relationship between the morphology of individual powder particles and the printing process has not been adequately documented yet. This article presents a detailed microscopic analysis of virgin and reused powder particles of maraging steel. Metallographic observation was performed using a scanning electron microscope (SEM). Detailed analyses of individual particles were carried out using SEM with a focused ion beam (FIB) milling capability. Analyses of elemental distribution and phase distribution were performed using EDS and EBSD, respectively. The findings have led to a better understanding and prediction of defects in additive-manufactured products.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

The characteristics of powders on a bulk scale are heavily influenced by both the material properties and the size of their primary particles. Throughout the stages of storage and transportation in the powder processing industry, various forms of deformation and stress, such as pressure and shear, impact these materials. Recognizing the point at which a powder undergoes yielding becomes particularly significant in numerous applications. There are also times when you need to understand the level of stress needed to maintain it. Measurement of powder yield and flow properties remains a challenge and is addressed in this study. As part of the CALIPER collaborative project, a number of shear experiments were performed using two shearing devices: Schulze ring shearing device and Anton Paar Powder Cell (APCC). These experiments have three purposes: i) Test reproducibility/consistency between two shear devices and test protocols. ii) To relate bulk behavior to microscopic particle properties, focusing on bulk density and thus the effect of cohesion between particles; iii) Investigate the influence of the temperature of heated powders on the powder flow properties, which is important for the industrial reactors. Interestingly, for samples with small particle size, bulk cohesion increases slightly, but bulk friction increases significantly, because of particle interaction effects. The experimental data not only provide useful insight into the role of microscopically attractive van der Waals gravitational and/or compressive forces on the macroscopic flow behavior of bulk powders, but also have industrial relevance. We also provide a robust datas of cohesive and attritional fine powder for silo design used for calibration and validation of silos, models and computer simulations.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

The application of solvent method in the preparation of polypropylene powders was investigated, including the influence of various technological conditions, such as the raw material melt index of polypropylene, processing temperature, dosage of the solvent and the packing pressure. The experimental data show that using solvent method can effectively produce polypropylene powder, and the optimal technological conditions are: melt index of polypropylene being about 17.8 g/10min, processing temperature being about 166.0 ℃, dosage of the solvent being about 0.067g/ml and the packing pressure being about 0.7MPa.Under this technological conditions, polypropylene powder with excellent sphericity could be prepared, the apparent density of powder can reach 0.40 g/cm3 and the prepared powder displayed a narrow size distribution with the mean size of about 42.7 µm.

Mee (Madhuca longifolia) is an important economic tree growing throughout the subtropical region of the Indo-Pak subcontinent. Mee seed constituents have distinctive chemical properties and thus provide nutritional and functional characteristics to the mee fat. The mee seed fat is an edible fat which can provide fat requirement of human diet in an economical way. Research on potential utilizations, understanding on the chemical composition, nutritional value and industrial applications of mee fat is important for efficient use mee seed fat. There were some reports available on potential applications of mee fat in food processing industry. But presently mee fat can be considered as an underutilized seed fat. In India mee fat used for edible purposes for a certain extent with compare to Sri Lanka. Therefore, more scientific researches should conduct on Sri Lankan mee varieties on edible purposes and popularized edible uses of Mee fat in Sri Lanka. Scientific knowledge and agricultural tools should effectively apply to make mee fat beneficial for its commercial applications. This chapter summarizes recent research work and studies available on botany, phytochemistry, functional properties, processing as well as food and non-food industrial applications of mee fat and other valuable parts of mee tree.

Dietary intake and alcohol consumption might be influenced by genetic variations in taste receptor genes. The objectives of this study were to examine the relationship between polymorphisms in bitter taste receptor genes TAS2R13 (rs1015443) and TAS2R38 (rs1726866, rs10246939, and rs713598) as well as alcohol consumption and body fat percentage in college students. Four hundred and two students with a mean age of 20.2 years participated in this study. An NIH Diet History Questionnaire (DHQ II) was used to collect data on their dietary intake, while AUDIT survey was used to determine their level of alcohol consumption. Bitter taste receptor gene polymorphisms were assessed by TaqMan allelic discrimination assays. Despite significant associations between TAS2R13 (rs101544) and certain aspects of alcohol consumption, including the frequency of alcohol intake, no indeed significant associations were found between TAS2R13 (rs1015443) and alcohol consumption after accounting for confounding variables in the regression model. Neither association was found regarding percent of body fat. In contrast, ethnicity and gender significantly influenced percent of body fat (p < 0.001), while no significant association was observed between TAS2R13 (rs1015443) and percent of body fat. Likewise, TAS2R38 (rs1726866, rs10246939 and rs713598) demonstrated no significant association with alcohol consumption and percent of body fat. These results were controlled for confounding factors, such as ethnicity and gender. Body fat percentage and alcohol consumption may be influenced by ethnicity, gender and age rather than SNPs of TAS2R13 and TAS2R38 genes. Assessing the taste genes’ interactions with diet and body composition might be useful in identifying human disease risk.

The incidence of obesity which leads to insulin resistance (IR) and metabolic disorder increases in developing countries including Indonesia. Male adult has higher risk to have abdominal obesity than female which is associated with cardiometabolic disorders. Several anthropometric measurements have been proposed to predict IR. The aim of this study was to investigate whether body mass, body mass index (BMI), waist circumference (WC), body fat percentage (BF) or visceral fat percentage (VF) could become a better predictor of IR in healthy young male adult. Total of 140 healthy young male adults ranging from 18-25 years were recruited in the study. Insulin resistance was measured by calculating Homeostatic Model Assessment for Insulin Resistance (HOMA-IR). Subjects with HOMA-IR value >75th percentile with cut off 3.75 were defined as IR. Anthropometric measurements included body weight, BMI, WC were performed whereas BF and VC were measured by bioelectrical impedance analysis (BIA). IR had significant strong correlation with body weight, BMI, WC, BF and VF. The area under curve of body mass, BF, VF were greater than WC and BMI. Anthropometric measurements correlated strongly with IR but body weight, BF, VF have stronger correlation than WC and BMI in healthy young male adult.

To understand the mechanisms involved in the anti-obesity effects Centella asi-atica (CA), we examined body weight, serum levels, white adipose tissue (WAT) weight, histological analysis, and the expression of cholesterol homeostasis- and lipid metabolism-related genes in mice with high-fat, high-sugar diet (HFHSD)-induced obesity that were orally treated with CA for 12 weeks. Eight-week-old, male C57BL/6J mice were assigned to the following four groups (eight mice/group): NOR, normal diet; Control, HFHSD; CA-L, HFHSD+CA 300 mg/kg; CA-H, HFHSD+CA 600 mg/kg. CA treatment signifi-cantly attenuated HFHSD-induced increase in body weight gain, serum glucose, serum triacylglycerol, and WAT weight (p < 0.05). Compared to that in Control group, adipocyte diameter and macrovesicular area of epididymal WAT signif-icantly decreased with CA treatment (p < 0.05). The mRNA expression levels of peroxisome proliferator-activated receptor gamma (PPARγ), fatty acid synthase (FAS), cluster of differentiation 36 (CD36), 3- hydroxyl-3-methylglutaryl CoA reductase (HMGCR), and stearoyl CoA desaturase 1 (SCD 1) were significantly downregulated in the CA-H group compared to the Control group (p < 0.05). CA exerts anti-obesity effects by lowering body fat accumulation via regulat-ing gene expression in the liver and thus, is a potential lipid-lowering agent.

Curcumin is the main secondary metabolites of Curcuma longa and other Curcuma spp, and has been reported to have some potential in preventing and treating some physiological disorders. This study investigated the effect curcumin in inhibiting high-fat diet and streptozotocin (STZ)-induced hyperglycemia and hyperlipidemia in rats. Twenty-six male Sprague-Dawley (SD) rats (170-190 g) were randomly divided into a standard food pellet diet group (Control group), a high-fat diet and streptozotocin group (HF+STZ group), and a high-fat diet combined with curcumin and STZ group (HF+ Cur +STZ group). Compared with the HF+STZ group, the HF+Cur+STZ group exhibited significantly reduced fasting blood glucose (FBG), total cholesterol (TC), triglyceride (TG), low-density lipoprotein cholesterol (LDL-C), high-density lipoprotein cholesterol (HDL-C), alanine aminotransferase (AST) and aspartate transaminase (ALT) levels, and liver coefficients; in the livers of these rats, the expression of malondialdehyde (MDA) and Bax was downregulated, whereas that of superoxide dismutase (SOD) and Bcl-2 was upregulated. Moreover, the liver histology of these rats was improved and resembled that of the control rats. These results suggest that curcumin prevents high-fat diet and STZ-induced hyperglycemia and hyperlipidemia, mainly via anti-oxidant and anti-apoptotic mechanisms in the liver.

Common genetic variants of the fat mass and obesity associated (FTO) gene are strongly associated with obesity and type 2 diabetes. FTO is ubiquitously expressed, but appears to have tissue-specific roles. Earlier studies have focused on the role of hypothlamic FTO in the regulation of metabolism. However, it appears that FTO plays a role in the regulation of metabolism in a tissue-specific manner. Recent studies suggest that expression of hepatic FTO is regulated by metabolic signals such as nutrients and hormones and altered FTO levels in liver affects glucose and lipid metabolism. This review outlines recent findings on hepatic FTO in the regulation of metabolism, with particular focus on hepatic glucose and lipid metabolism. It is proposed that abnormal activity of hepatic signaling pathways involving FTO links metabolic impairments such as obesity, type 2 diabetes and nonalcoholic fatty liver disease (NAFLD). Therefore, a better understanding of these pathways may lead to therapeutic approaches to treat these metabolic diseases by targeting hepatic FTO. The overall goal of this review is to place FTO within the context of hepatic regulation of metabolism.

Accurate estimation of body fat percentage is essential for various health and fitness applications. Traditional methods for measuring body fat, such as underwater weighing, can be costly and inconvenient. In this study, we apply machine learning techniques to predict body fat percentage using easily accessible body measurements and data. The results highlight the effectiveness of regression models in estimating body fat, with Linear Regression, Ridge Regression, and Bayesian Ridge models achieving R-squared scores of approximately 74%, 73%, and 73%, respectively. These models provide a practical and cost-effective solution for individuals and professionals seeking reliable body fat estimates.

The current study emphasizes on optimizing a suitable ratio of enzymatically hydrolyzed potato powder (EHPP) and whole milk powder (WMP) to produce a quality yogurt by evaluating the physicochemical and rheological properties. The results showed that the addition of EHPP decreased the pH towards acidic conditions which resulted in the high acidity of yoghurt. The proximate composition showed that EHPP increased the ash, protein, water holding capacity (WHC) while fat, synersis, color parameters and total solid were decreased when compared to control yoghurt (CY) sample. Moreover, texture profile (TPA) analysis showed that the addition of EHPP decreased the hardness and cohesiveness while springiness did not show significant difference. Furthermore, rheological properties revealed that EHPP decreased the storage modulus (G’) and loss modulus (G”) when compared with control. In addition to this, sensory analysis revealed that the treatment P4M (1:3) was found as optimum ratio regarding taste, flavor, and aroma. Besides this, scanning electron microscopy (SEM) confirms that the high amount of EHPP resulted in the void holes while CY showed dense gel structure. The prepared yogurt with EHPP provides an excellent flavor, satisfying sweetness and homogeneous texture. These findings suggest the optimum formulation ratio of prepared yogurt was found to be P4M (1:3) for desirable attributes and consumer acceptance. The prepared yogurt from the EHPP presents the potential industrial applications.

The purpose of this work was analysing the compaction of a cohesive material using different DEM simulators to determine the equivalent contact models and identify how some parameters of the simulations affect the compaction results (maximum force and compacts appearance) and computational costs. For that purpose, three cohesion contact models were tested (‘linear cohesion’ in EDEM; ‘SJKR’ and ‘SJKR2’ in LIGGGHTS). The influence of the particle size distribution (PSD) on the results was also investigated. Further assessments were performed on the effect of selecting different timesteps, using distinct conversion tolerances for exporting the 3D models to STL files and moving the punch with different speeds. Consequently, it was possible to determine that a timestep equal to a 10% Rayleigh timestep, a conversion tolerance of 0.01 mm and a punch speed of 0.2 m/s are adequate for simulating the compaction process using the contact models in this work. In addition, the results determined that the maximum force was influenced by the PSD because of the rearrangement of the particles. The PSD was also related to the computational cost because of the number of simulated particles and their sizes. Finally, an equivalence was found between the linear cohesion and SJKR2 contact models

Powder Bed Fusion (PBF) is a type of Additive Manufacturing (AM) technology that builds parts in a layer-by-layer fashion out of a bed of metal powder via the selective melting action of a laser or electron beam heat source. The technology has become widespread, however the demand is growing for closed loop process monitoring and control in PBF systems to replace the open loop architectures that exist today. This paper demonstrates the simulated efficacy of applying closed-loop state estimation to the problem of monitoring temperature fields within parts during the PBF build process. A simplified LTI model of PBF thermal physics with the properties of stability, controllability and observability is presented. An Ensemble Kalman Filter is applied to the model. The accuracy of this filters’ predictions are assessed in simulation studies of the temperature evolution of various test parts when subjected to simulated laser heat input. The significant result of this study is that the filter supplied predictions that were about 2.5x more accurate than the open loop model in these simulation studies.

Cellular substructure has been widely observed in the sample fabricated by laser powder bed fusion, while its growth direction and the crystallographic orientation have seldom been studied. This research tries to build a general model to construct the substructure from its two-dimensional morphology. All the three Bunge Euler angles to specify a unique growth direction are determined, and the crystallographic orientation corresponding to the growth direction is also obtained. Based on the crystallographic orientation, the substructure in the single track of austenitic stainless steel 316L is distinguished between the cell-like dendrite and the cell. It is found that, with the increase of scanning velocity, the substructure transits from cell-like dendrite to cell. When the power is 200 W, the critical growth rate of the transition in the single track can be around 0.31 ms^-1.

This work presents an analytical methodology to predict meat juiciness (discriminant semi-quantitative analysis using groups of intervals of intramuscular fat) and intramuscular fat (regression analysis) in Longissimus thoracis et lumborum (LTL) muscle of Bísaro pigs using as independent variables the animal carcass weight and parameters from color and image analysis. These are non-invasive and non-destructive techniques which allow development of rapid, easy and inexpensive methodologies to evaluate pork meat quality in a slaughterhouse. The proposed predictive supervised multivariate models were non-linear. Discriminant mixture analysis to evaluate meat juiciness by classified samples into three groups—0.6 to 1.1%; 1.25 to 1.5%; and, greater than 1.5%. The obtained model allowed 100% of correct classifications (92% in cross-validation with seven-folds with five repetitions). Polynomial support vector machine regression to determine the intramuscular fat presented R2 and RMSE values of 0.88 and 0.12, respectively in cross-validation with seven-folds with five repetitions. This quantitative model (model’s polynomial kernel optimized to degree of three with a scale factor of 0.1 and a cost value of one) presented R2 and RSE values of 0.999 and 0.04, respectively. The overall predictive results demonstrated the relevance of photographic image and color measurements of the muscle to evaluate the intramuscular fat, rarther than the usual time-consuming and expensive chemical analysis.

Maternal milk, from well-nourished and healthy mothers, is a source of several bioactive compounds and balanced nutrients required for proper growth and development of the infant. Hence it is regarded as the optimal form of nourishment. Human milk fat from human milk is the most crucial component and is a necessity for the growing infant. However, in certain cases, the breast milk may fulfill the nutritional needs or the breast-feeding of the infant is not feasible; infant formulae are then considered as the best alternative as nutritional support. It becomes essential for the infant formula to behave and provide nutritive support in the same way as human milk. In order to achieve so, the most crucial components of all should also be prepared precisely, i.e., the analogue of human milk fat. This analogue, which mimics the actual human milk fat, can be then used as a prime ingredient while designing the infant formula. Significant research and several advances have been made in preparing the infant formula enriched with adequate fat content, and more studies are still being conducted in order to achieve a more sound product in the most economical and simplest way possible.

Formula feeding, as an alternative to breastfeeding, offers benefits such as convenience and consistent nutrition. Among the drawbacks of formula feeding, however, is potential dilution or concentration errors in the of formula during preparation that may lead to infant health issues. The present study aimed to investigate the accuracy of caregiver measurements as they prepared infant formula under multiple conditions, compared with manufacturer specifications. A diverse sample of caregivers (N = 84) participated in this cross-over experimental study. Participants hand-scooped infant formula powder and poured water to prepare 4oz and 7oz feedings, using both a standardized set of infant formula products and participants’ own products. Linear mixed effects models were used to estimate fixed effects of target amount (4oz versus 7oz) and products (participant versus researcher) on mean absolute percent error (MAPE) of measurement. Across all conditions MAPE was significantly greater for measuring powder than for water (9.0% vs. 4.4%; p&lt;0.001) with a combined powder and water MAPE at 13.0%. Greater measurement error was associated with the odd-sized 7oz preparation and participants’ own products. We observed considerable variability and substantial error during infant formula preparation, particularly for hand-scooping of powder, which tended toward higher values than the theoretical gold standard.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

Powder bed fusion (PBF) process is a metal additive manufacturing process which can build parts with any complexity from a wide range of metallic materials. PBF process research has predominantly focused on the impact of only a few parameters on product properties due to the lack of a systematic approach for optimizing a large set of process parameters simultaneously. The pivotal challenges regarding this process require a quantitative approach for mapping the material properties and process parameters onto the ultimate quality; this will then enable the optimization of those parameters. In this study, we propose a two-phase framework for optimizing the process parameters and developing a predictive model for 316L stainless steel material. We also discuss the correlation between process parameters -- i.e., laser specifications -- and mechanical properties and how to achieve parts with high density (> 98%) as well as better ultimate mechanical properties. In this paper, we introduce and test an innovative approach for developing AM predictive models, with a relatively low error percentage of 10.236% that are used to optimize process parameters in accordance with user or manufacturer requirements. These models use support vector regression, random forest regression, and neural network techniques. It is shown that the intelligent selection of process parameters using these models can achieve an optimized density of up to 99.31% with uniform microstructure, which improves hardness, impact strength, and other mechanical properties.

Traditionally Moringa is known as mystical miracle tree or the tree of life. Soup can be classified as an appetizer, warm food during cold and sick. Moringa oleifera pods have been procured from College of Agriculture, JNKVV, Jabalpur. The present investigation is planned with objectives to standardize best combination of for the development of instant soup mix, to evaluate various quality parameters, to evaluate the storage stability and cost estimation of product. Protein in instant soup is ranged from 9.76 to 11.89 percent in different formulations of instant soup mix. Formulation MPP4 (11.89) had significantly maximum protein content followed by MPP3, MPP2, MPP1 and Control with the minimum protein content. The original instant soup mix (control) exhibited highest carbohydrate content (61.52%) followed by MPP1, MPP3, MPP4, and MPP2 with lowest content. The evaluated scores of control for colour and appearance, taste, flavour, consistency, after taste and overall acceptability are 8.36, 8.50, 8.60, 8.90, 8.76 and 8.63 respectively

Metal powder bed fusion (PBF) additive manufacturing (AM) builds metal parts layer by layer upon a substrate material. The strength of this interface between substrate and printed material is important to characterize, especially in applications where the substrate is retained and included in the finished part. This paper studied the tensile and torsional strengths of wrought and additively manufactured (through PBF) SS316L and compared them to specimens composed of half wrought material and half PBF material. The PBF specimens consistently exhibited higher strength and lower ductility than the wrought specimens. The hybrid PBF/wrought specimens performed similarly to the wrought material. In no specimens did any failure appear to occur at or near the interface between wrought substrate and PBF material. In addition, most of the deformation in the PBF/wrought specimens appeared to be limited to the wrought portion of the specimens. These results are consistent with microscopy showing smaller grain size in the PBF material, which often leads to increased strength in SS316L due to the Hall-Petch relationship.

The microstructural evolution, thermodynamics and kinetics of Mo-21%Tm₂O₃ (mass fraction, %) powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm₂O₃ to be decomposed and then dissolved into Mo crystal. The supersaturated nanocrystalline solid solution of Mo (Tm, O) was obtained after 96 h of ball milling. The elements of Mo, Tm and O were distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo-21%Tm₂O₃, it was mechanical work, not negative heat of mixing, that provided the driving force to form supersaturated nanocrystalline Mo (Tm, O) solid solution.

This work deals with the analysis of phase composition of sintered Ti-Al-C composite materials under high voltage electrical discharge. The samples of Ti-Al-C powder composites were tested by SEM, Raman spectroscopy and XRD. It was determined that the treatment of the powder by high voltage electrical discharge (HVED) and further sintering at high temperatures using the method of spark plasma sintering (SPS) encourages the formation of the intermetallic reinforcing phases, carbides and different nanocarbon structures like graphene and fullerenes, as well as pure graphite. Intermetallic phases and nanocarbon structures improve mechanical and physical properties of the composites. By using experimental methods mentioned above, the phase composition of Ti-Al-C powder composites obtained at different sintering temperatures was determined.

Rapid and accurate prediction of residual stress in metal additive manufacturing processes is of great importance to guarantee the quality of the fabricated part to be used in a mission-critical application in the aerospace and automotive industries. Experimentation and numerical modeling are valuable tools for measuring and predicting the residual stress; however, to-date conducting experimentation and numerical modeling is expensive and time-consuming. Thus, herein, a physics-based thermomechanical analytical model is proposed to predict the residual stress of the additively manufactured part rapidly and accurately. A moving point heat source approach is used to predict the temperature field by considering the effects of scan strategies, heat loss, and energy needed for solid-state phase transformation. Due to the high temperature gradient in this process, part experiences a high amount of thermal stress following solidification which may exceed the yield strength of the material. The thermal stress is obtained using Green’s function of stresses due to the point body load. The Johnson-Cook flow stress model is used to predict the yield surface of the part under repeated heating and cooling. As a result of the cyclic heating and cooling and the fact that the material is yielded, the residual stress build-up is predicted based on incremental plasticity and kinematic hardening behavior of the metal according to the property of volume invariance in plastic deformation in coupling with the equilibrium and compatibility conditions. The computational methodology is realized with the laser powder fusion of maraging steel 350 as a material of example. The validation of the predictive models has been presented in terms of the comparison of predicted and measured scan-direction and build-direction residual stress distributions along depth of build under various process parameter combinations. Moreover, for the first time, the Jonson-Cook parameters of maraging steel 350 are predicted using analytical modeling of machining forces and non-linear optimization techniques.

This study used eco-friendly materials known as Periwinkle Shell Powder (PSP) in stabilizing the engineering properties of lateritic soil. Preliminary test was performed on the un-stabilized lateritic soil for the purposes of identification and classification (natural moisture content, liquid limits, plastic limits, and plasticity index). The engineering tests were conducted on the lateritic soil stabilized with additions of (2, 4, 6, 8 and 10 %) PSP and OPC respectively. The result showed that cement gave a progressive increase in the Maximum Dry Density (MDD) of the lateritic soil from 1875 kg/m3 (2 %) to 2294 kg/m3 (10 %) respectively. This represents 22 % increase in the MDD from the un-stabilized state. For PSP, the Maximum MDD was attained at 6 % (1974 kg/m3), representing 5.3 % increase in MDD of the soil from the un-stabilized state. For both stabilizing agent, the Optimum Moisture Content (OMC) increases from 13.65 % to 13.83 % and from 11.72 % to 14.41 % for Cement and Periwinkle Shell Powder respectively. PSP recorded an increase of 5.6 % of CBR value compared with OPC that recorded an increase of 34 % CBR value. The study therefore concluded that Periwinkle Shell Powder (PSP) could be considered as good stabilizer for clayey or lateritic, and its uses as a stabilizer could also provide a big relief to the environmental pollution caused by its indiscriminate dumping.

Commercially pure (c.p.) iron powders with a deliberate high degree of oxidation were consolidated by medium-frequency electrical resistance sintering (MF-ERS). This is a consolidation technique where pressure, and heat coming from a low-voltage and high-intensity electrical current, are simultaneously applied to a powder mass. In this work, the achieved densification rate is interpreted according to a qualitative microscopic model, based on the compacts global porosity and electrical resistance evolution. The effect of current intensity and sintering time on compacts was studied on the basis of micrographs revealing the porosity distribution inside the sintered compact. The microstructural characteristics of compacts consolidated by the traditional cold-press and furnace-sinter powder metallurgy route are compared with results of MF-ERS consolidation. The goodness of MF-ERS versus the problems of conventional sintering when working with oxidized powders is analyzed. The electrical consolidation allows to obtain higher densifications than the traditional route under non-reducing atmospheres.

The 2020-2025 Dietary Guidelines for Americans recommends limiting intakes of saturated fat and added sugars (SF/AS) to 88% of the representative sample of U.S. adults. The top sources of SF were cheese, pizza, ice cream, and eggs. The leading sources of AS were soft drinks, tea, fruit drinks, and cakes and pies. This analysis reflects a parsimonious approach to reliably identify foods and beverages that contribute to SF/AS intakes in U.S. adults.

Wasted Green tuff powder produced by cutting Towada stone is recycled as environmental cleaning material. The optimum temperature for green tuff powder calcination to reduce the hydroxyl radical produced in hydrogen peroxide decomposition with ultraviolet light (UV) and no light. The green tuff calcined at 800 °C shows the large decomposition rate of hydrogen peroxide with no UV light when measured by using ESR. With UV light, the optimum temperature for calcinating the green tuff powder in order to reduce hydroxyl radical is also 800 °C. Next, the powder calcined at 800 °C is used to produce the tile by compression and heating, and then the formaldehyde adsorption rate was measured. The green tuff powder calcined at 800 °C showed a high adsorption rate, similar to that of the activated carbon. The tiles formed at 40 MPa and heated st 1100 °C were the strongest and also adsorbed formaldehyde. The adsorbed formaldehyde on the green tuff tile and powder might have a possibility to decompose by photocatalytic.

Arthrospira platensis is the widely available source of spirulina and contains distinctive natural pigments including carotenoids and C-phycocyanin (C-PC). In this study, the major carotenoid and C-PC contents were determined in seven commercially available spirulina powder products and laboratory-prepared A. platensis trichomes (AP-1) by an LC-DAD method and a UV-Visible spectrometry, respectively. The correlation of these two pigment content levels with Hunter color coordinates and antioxidant activity was also evaluated. The L* value failed to show a significant correlation with pigment content, but a positive correlation was observed between a* values and the contents of total carotenoid and C-PC. As b* values decreased, the total carotenoid and C-PC contents increased. AP-1 exhibited the highest content of total carotenoids, chlorophyll a and C-PC, and antioxidant activities among the samples. This observation could be related to degradation of these pigments during the mass production process. The carotenoid profiles suggested that the commercial spirulina powders originated from two different sources, A. platensis and A. maxima. Total carotenoid and C-PC content exhibited positive significant correlations with antioxidant activities measured by DPPH and ABTS assays. These results provide a strong scientific foundation for the establishment of standards for the commercial distribution of quality spirulina products.

Due to the high specific surface area of titanium aluminide powders, significant and unavoidable surface oxidation takes place during processing. The resulting oxides disrupt the conventional powder metallurgical process route (pressing and sintering) by reducing green strength and sintered properties. Oxide-free particle surfaces offer the potential to significantly increase particle bond strength and enable the processing of difficult-to-press material powders. In this work, the effect of milling titanium aluminide powder in a silane-doped atmosphere on the component properties after pressing and subsequent sintering was investigated. Ball milling was used to break up the oxide layers and create bare metal surfaces on the particles. With the help of silane-doped inert gas, the oxygen partial pressure was greatly reduced during machining. It was investigated whether oxide-free surfaces could be produced and maintained by milling in silane-doped at-mospheres. Furthermore, the resulting material properties after pressing and sintering were an-alyzed using density measurements, hardness tests, EDX-measurements and micrographs. It was concluded, that ball milling in a silane-doped atmosphere produces and maintains oxide-free particle surfaces. These oxide-free surfaces and smaller particle sizes improve the component properties after pressing and sintering.

Aloe Vera leaves have a great potential as an economic supplement with an adequate nutritional profile. In this study, Aloe Vera leaf gel (AVG) powder was used to fortify plain cakes. Freeze drying of AVG was performed for the production of Aloe Vera powder (ALP) and four plain cakes were prepared with different proportions of ALP for further investigation. Analysis suggested that ALP contained significantly (p&lt;0.05) higher amount of protein (22.23 vs 12.24), ash (19.83 vs 0.64) and iron (175 vs 3.05) content than refined wheat flour (RWF). ALP also contained significant amount of total polyphenols and antioxidant. Moisture, protein, ash, weight, and minerals (Fe, Ca) content were higher (p&lt;0.05) in ALP-cakes; whereas fat, volume, specific volume, height, baking loss, and total carbohydrate content were higher (p&lt;0.05) in RWF-cakes. Incorporation of 6 and 8% ALP in the formulation increased the total polyphenols and anti-oxidant activity in plain cakes. Texture analysis revealed that hardness and chewiness increased in ALP-cakes but decreased in RWF-cakes, however, cohesiveness, springiness, and chewiness decreased in ALP-cakes. Sensory attributes suggested that 4% ALP incorporated cake was attributed as the best formulation. In conclusion, ALP can be supplemented in cakes up to 8% to improve the nutrient value.

Background: Heart failure is a major cause of morbidity and mortality worldwide; left ventricular diastolic dysfunction plays a leading role in this clinical context. Diastolic dysfunction may be predisposed by increased abdominal fat and, consequently, increased pericardial and epicardial adiposity. This study aimed to determine whether pericardial and epicardial fat are associated with left ventricular diastolic function. Methods: 82 patients had their abdominal circumference measured and underwent transthoracic echocardiography to measure the thickness of pericardial and epicardial fat and assess the left ventricular diastolic function. Two groups were created based on mean pericardial fat thickness (4.644 mm) and were related to abdominal circumference and echocardiographic parameters. Results: Subjects in the PF High group showed a significant decrease in septal e' (p&lt;0.0001), lateral e' (p&lt;0.0001) and E/A ratio (p=0.003) and a significant increase in E/e' ratio (p&lt;0. 0001), E wave deceleration time (p=0. 013), left atrial volume (p&lt;0.0001), LV mass (p=0.003), tricuspid regurgitant jet velocity (p&lt;0.0001) and LV diameter (p=0.014) compared to the PF Low group. Conclusions: Measurement of abdominal circumference, pericardial and epicardial fat is an early indicator of diastolic changes with transthoracic echocardiography being the gold standard exam.

This study sought to improve the nutritional, functional and biochemical properties of pearl millet through malting and fermentation. Moringa oleifera leaf powder (MLP) was used as a fortificant. Mixture design was used to find optimal proportions for each of the components that yield a high protein and or low saturated fat content. Twelve mixtures with varying ratios of fermented, and malted pearl millet flour ranging between 30–65%, and MLP between 5–15% were generated through I-Optimal mixture design. The mixtures were wet-cooked, freeze-dried and analyzed for protein and fat content. The data obtained were fitted to a linear mixture model and the search for the optimum was done using Numerical Optimization for maximising protein and minimising saturated fat. The linear model was suitable for explaining variation for total protein and saturated fat with r2 of 0.50 and 0.51, respectively. Increasing MLP increased protein content. Two final formulations were generated through the optimization process. Pearl millet’s protein content increased by up to 22% while saturated fat decreased by up to 13%. Ash content increased by 75%. Polyphenol content and oxygen radical absorbance capacity increased by 80% and 25%, respectively. Final and peak viscosity were reduced by 90% and 95%, respectively.

Laser powder bed fusion can fabricate porous structure through lattices, but it remains a challenge to prepare micropores (

The importance of both recycling and additive manufacturing (AM) is increasing, however there has been a limited focus on development of AM alloys that are recyclably compatible with the larger scrap loops of wrought 5xxx, 6xxx and cast 3xx aluminium alloys. In this work the powder bed fusion (PBF) printability of AlMgSi alloys in the interval of 0-30wt%Mg and 0-4wt%Si is screened experimentally with a high throughput method. This method produces PBF mimicked material by PVD co-sputtering followed by laser remelting. Strong evidence was found for AlMgSi alloys being printable in two different composition ranges; Si+Mg<0.7wt% or for Si+2/3Mg>4wt% when Mg < 3wt% and Si > 3wt%. Increasing the amount of Mg and Si influence the grain structure by introducing fine columnar grains at the melt pool boundary, although the melt pool interior was unaffected. Hardness in as-built state increased with both Mg and Si, alt-hough Si had neglectable effect at low levels of Mg. Both evaporative loss of Mg and the amount of Mg in solid solution increased linearly with the amount of Mg.

Powder mixture with given molar ratio Ca/P = 1.67 consisting of brushite (calcium hydrophosphate dihydrate) CaHPO4·2H2O, calcium oxalate monohydrate CaC2O4·H2O in form of whewellite and weddellite and some quantity of quasi-amorphous phase was obtained as a result of the interaction of hydroxyapatite powder Ca10(PO4)6(OH)2 with an aqueous solution of oxalic acid H2C2O4 at a molar ratio of Ca10(PO4)6(OH)2/H2C2O4 = 1:4 under mechanical activation conditions. This powder mixture was used to produce microporous monophase ceramics based on hydroxyapatite Ca10(PO4)6(OH)2 with aperient density of 1.25 g/cm3 after firing at 1200 oC. Microporosity of sintered ceramics was formed due to presence of particles with plate-like morphology, restraining shrinkage during sintering. Microporous ceramics based on hydroxyapatite Ca10(PO4)6(OH)2 with roughness of the surface as a consequence of the created microporosity can be recommended as a biocompatible material for the bone defects treatment and as a substrate for bone cell cultivation.

The present study analyzed the efficiency of a naturally derived fenugreek powder for removal of Congo red dye from the aqueous solution. The flocculation Studies on Congo Red (CR) a hazardous, textile dye onto Fenugreek Powder and its adsorption was analyzed. Fenugreek Powder is Eco-friendly, biodegradable and locally available in the market. The dye adsorption process was performed in different batches at varying pH, dye concentration, adsorbent concentration and contact time to get the best results. The result showed that the maximum removal of dye was 42.4% with 10mg/l of Fenugreek powder at pH 4.

The relationship between epicardial adipose tissue (EAT) and atrial fibrillation (AF) has gained interest in recent years. Previous literature on the topic presents great heterogeneity, focusing especially on computed tomog-raphy imaging. Aim of the present study is to determine whether an increased volume of left atrial (LA) EAT evaluated at routine pre-procedural cardiac magnetic resonance imaging (MRI) relates to AF recurrences after catheter ablation. 50 patients undergoing AF cryoballoon ablation and pre-procedural cardiac MRI allowing quantification of LA EAT were enrolled. In one patient segmentation of LA EAT could not be achieved. After a median follow-up of 16.0 months, AF recurrences occurred in 17 patients (34%). Absolute volume of EAT was not different in patients with and without AF recurrences (10.35 ml vs. 10.29 ml; p-value=0.963), whereas volume of EAT indexed on the LA (EATi) was lower, albeit non statistically significant, in patients free from arrhythmias (12.77% vs. 14.06%; p-value=0.467). Receiver operating characteristic curve testing the ability of EATi to predict AF recurrence after catheter ablation showed sub-optimal performance (AUC: 0.588). The finest identified cut-off of EATi was 10.65%, achieving a sensitivity of 0.5, a specificity of 0.82, a positive predictive value of 0.59 and a negative predictive value of 0.76. Patients with values of EATi lower than 10.65% showed greater survival free from arrhythmias than patients with values above this cut-off (84% vs. 48%; p-value=0.04). In conclusion, indexed LA EAT volume evaluated at cardiac MRI independently relates to arrhythmia recurrence after AF cryoballoon ablation.

The type of tail of sheep is an important economic trait. However, the candidate genes associated with the tail type are uncertain. The objective of this study was to identify the genetic region and genotype responsible for the tail type phenotype. Here we perform a genome-wide association study (GWAS) in 40 large tailed Han sheep and 40 Altay sheep as case and 40 Tibetan sheep as control. The results indicated that a total 31 genome-wide significant SNPs associated with type of tail traits were detected. For significant SNPS loci, determine its physical location, and screening of candidate genes within section. By combining information of previously reported and annotated biological functional genes, we identified SPAG17, Tbx15, VRTN, NPC2, BMP2 and PDGFD as the most promising candidate genes for type of tail traits. Based on the above identified candidate genes on type of tail traits, we selected BMP2 and PDGFD to conduct the genetic effect analysis in a large Altay sheep and Tibetan sheep population. Rs119 T>C in the exon1 of BMP2 gene and 1 SNPs in the exon4 (rs69 C>A) of PDGFD gene were detected, rs119 that located on exon1 of BMP2 gene was TT genotype in Altay sheep, while with CC genotype in Tibetan sheep. On rs69 of PDGFD gene, Altay sheep with CC genotype, however, Tibetan sheep with AA genotype. These results indicated that the significant associations of SNPs detected in GWAS were indirectly caused by the genetic effects of BMP2 and PDGFD on sheep tail fat deposition.

Dietary recommendations to decrease the risk of cardiovascular disease (CVD) have focused on reducing intake of saturated fatty acids (SFA) for more than 50 years. While the 2015-2020 Dietary Guidelines for Americans advise substituting both monounsaturated and polyunsaturated fatty acids for SFA, evidence supports other nutrient substitutions that will also reduce CVD risk. For example, replacing SFA with whole grains, but not refined carbohydrates, reduces CVD risk. Replacing SFA with protein, especially plant protein may also reduce CVD risk. While dairy fat (milk, cheese) is associated with a slightly lower CVD risk compared to meat, dairy fat results in a significantly greater CVD risk relative to unsaturated fatty acids. As research continues, we will refine our understanding of dietary patterns associated with lower CVD risk.

Agaricus bisporus is well known as a source of polysaccharides that could improve human health. The objective of this study was to explore anti-obesity effect of A. bisporus extract (H2Oslim®) abundant in polysaccharides and its underlying mechanism. Pancreatic lipase inhibitory activity in vitro was determined after treatment with H2Oslim® and chitosan. Treatment with H2Oslim® and chitosan significantly decreased pancreatic lipase activity. Five-week-old male SD rats were randomly divided into three groups for acute feeding with vehicle, H2Oslim® at 80 mg/kg body weight (BW)/day, and H2Oslim® at 160 mg/kg BW/day. H2Oslim® does-dependently increased plasma lipid clearance in an oral lipid tolerance test. Five-week-old male C57BL/6N mice were fed a control diet (CD), a high fat diet (HFD), an HFD with H2Oslim® at 80 mg/kg BW/day, H2Oslim® at 160 mg/kg BW/day, or chitosan at 160 mg/kg BW/day for eight weeks. HFD-fed mice showed significant increases of body weight, fat mass, white adipose tissue, average lipid droplet size, and serum levels of glucose, triglyceride, ALT, and AST compared to those in the CD group. However, H2Oslim® or chitosan administration ameliorated these increases. H2Oslim® or chitosan signifi-cantly reduced dietary efficiency and increased fecal excretion levels of lipid, triglyceride, and total cholesterol. These in vitro and in vivo findings suggest that H2Oslim® might act as an anti-obesity agent by inhibiting pancreatic lipase-mediated lipid absorption, at least in part.

The flowability of a powder is a characteristic dependent on both the particle ensemble's physical properties as well as the testing equipment and conditions. In powder bed additive manufacturing processes (SLM, EBM), flowability can be used to predict the quality of the deposited powder layer. However, how representative flowability is for the powder bed layer quality is not always clear.In this work, we compared several steel powders, as well as different testing methods. Each powder had an individual combination of composition or particle size distribution. Furthermore, the flowability testing equipment and methods were selected according to standards (Tap density, Hall flow) or referring to the published literature (angle of repose, FT4 Powder Rheometer). After measuring the flowability of different samples for each testing method, we created a database to evaluate a first correlation between the different testing methods. Finally, with a Powder Rheometer, we investigated for one sample some flow properties as function of different particle size distributions.

The COVID-19 pandemic has disrupted the supply chain for personal protective equipment (PPE) for medical professionals, including N95-type respiratory protective masks. To address this shortage, many have looked to the agility and accessibility of additive manufacturing (AM) systems to provide a democratized, decentralized solution to producing respirators with equivalent protection for last-resort measures. However, there are concerns about the viability and safety in deploying this localized download, print, and wear strategy. Several polymer-based AM processes produce porous parts, and inherent process variation between printers and materials also threaten the integrity of tolerances and seals within the printed respirator assembly. The goal of this paper is to quantitatively measure particle transmission through printed respirators of different designs, materials, and AM processes, and assess the viability of printed respirators as N95 equivalents. Results from this study show that respirators printed using desktop/industrial-scale fused filament fabrication processes and industrial-scale powder bed fusion processes have insufficient filtration efficiency at the size of the SARS-CoV-2 virus, even while assuming a perfect seal between the respirator and the user’s face. Almost all printed respirators provided <60% filtration efficiency at the 100-300 nm particle range. Only one respirator, printed on an industrial-scale fused filament fabrication system provided >90% efficiency as-printed. Post-processing procedures including cleaning, sealing surfaces, and reinforcing the filter cap seal generally improved performance, but no respirator sustained the filtration efficiency of an N95 respirator, which filters 95% of SARS-CoV-2 virus particles. Instead, the printed respirators showed similar performance to various cloth masks. While continued optimization of printing process parameters and design tolerances could be implemented to directly print respirators that provide the requisite 95% filtration efficiency, AM processes are not sufficiently reliable for widespread distribution and local production of N95-type respiratory protection without commensurate quality assurance processes in place. Certain design/printer/material combinations may provide sufficient protection for specific users, but the respirators should not be trusted without quantitative filtration efficiency testing. It is currently not advised to expect printed respirators originating from distributed designs to replicate performance across different printers and materials.

This study was aimed at investigating the effects of roasting and cryogenic milling on particle size, water solubility, and amount of bioactive components in ginseng root. Samples were pulverized by cryogenic milling, and one treatment condition was selected for each size range (10-50 μm, and >50 μm). The selected samples were roasted at different temperatures (160-200 °C) followed by cryogenic milling. Powdered samples were analyzed for their physicochemical characteristics. Results revealed that roasted samples exhibited significantly smaller particle size than controls (not roasted, p<0.05), and the particle size of roasted samples decreased with increase in roasting temperature until flocculation occurred around 180-190 °C. With decrease in particle size of ginseng; water solubility index, antioxidant activity, total polyphenol content, and total polysaccharide content were observed to increase. Ginseng samples showed an increasing trend in antioxidant activity with decreasing particle size (p>0.05) with significantly higher values for all roasted samples compared to the controls (p<0.05). Non-polar ginsenosides such as Rg2(S), Rg2(R), Rg3(S), Rg3(R), and Rh1(S) showed an increase in temperature-dependent manner. This study revealed that roasting at certain temperature range with cryogenic milling has positive effects on ginseng by reducing its particle size, and increasing water solubility and bioactive components.

This study aimed to decrease the particle size of ginseng by roasting and cryogenic milling to increase its water solubility and physiological activity. The samples were roasted for different times (9–21 min) and generated in different sizes (10–50, and > 50 μm). All roasted samples revealed significantly smaller particle sizes than did non-roasted samples based on Sauter mean diameter (D [3,2], p < 0.05). Further, the particle sizes of roasted samples decreased till roasting up to 15 min. In terms of the water solubility index (WSI), antioxidant activity, total polyphenol content (TPC), and total polysaccharides according to particle size, 10-20 μm-sized samples showed the highest values when compared with >50 μm-sized samples. Based on roasting time, WSI values of all samples roasted for up to 15 min were higher than those of the control (not roasted) (p < 0.05). Antioxidant activity and TPC also increased with increasing roasting time. Total polysaccharide content was the highest upon roasting for 15 min except for the 10-20 μm sample. Ginsenoside content of roasted samples >20 μm size was higher than that of the control (not roasted) except after 15 min of roasting. Therefore, roasting and cryogenic milling are effective in producing ginseng root powder.

The annual construction and demolition waste (CDW) generated from EU construction sector was 850 million tons, which represented 31% of the total waste generation and about 28% of CDW was ceramics (bricks and tiles). In this study, the feasibility of using CDW brick powder as the precursor of alkali activated mortar (AAM) and extruded polystyrene (XPS) as the lightweight aggregates to form lightweight brick powder AAM (LW-BP-AAM) for non-structural applications was investigated. The thermal conductivity of LP-BPAAM was 0.112 W/m·K with density of about 1,135 kg/m³ which was lower than the counterparts with similar density in literature. The acid resistance of LW-BP-AAM is comparable to conventional fly ash based AAM and superior than ordinary Portland cement. From the scanning electron microscopy with energy dispersive X-ray spectroscopy, there was no severe damage on the surface of LW-BP-AAM but aluminate was removed from the matrix which was further verified in Fourier transform infrared spectroscopy. The mass and strength loss of LP-BP-AAM was 1.5% and 33%, respectively. Although the compressive strength of the LP-BP-AAM was low (about 1.8 MPa), it can be improved by optimising the particle size of the XPS aggregates.

This study examines the association between dietary saturated fatty acid (SFA) intake and leukocyte telomere length (LTL) using data from the National Health and Nutrition Examination Survey (NHANES) 1999-2002. Telomeres, protective repeats of DNA at the ends of chromosomes, play a crucial role in cellular aging. Their length is shortened over time and is influenced by various factors, one of which is diet. The present study's objective was to evaluate whether increased SFA consumption is associated with shorter LTL. The analysis, conducted on a large, nationally representative sample of 6646 adults, revealed an inverse association between dietary SFAs and LTL. When examined further, this association was found to be significant in women, but not in men. Serum C-reactive protein (CRP) levels were tested as a potential mediator in this relationship, but no such mediation was found. These findings support the role of dietary factors in modulating cellular aging. However, further research is warranted to elucidate the underlying mechanisms driving the overall association, as well as the gender-specific effects observed.

In this study, the efficiency of coating (alginate and carrageenan) and osmotic dehydration pre-treatment (NaCl and sucrose) on decreasing oil uptake of potato strips was assessed. It was examined how various pre-treatments affected the sample’s texture, morphology, color and density properties as well as their moisture content and effective moisture diffusion coefficient (Deff). Results showed that NaCl osmotic dehydration pre-treatment and sucrose solution decreased oil uptake by 30.76% and 41.75%. This is attributed to moisture removal increasing caused by improving dielectric properties. Osmotic dehydration and coating pre-treatment frequently enhanced product shrinkage, browning index, a* and ∆E. Conversely, density, lightness, breaking force, Deff and b* decreased. In control samples, SEM revealed a severely damaged internal structure in comparison to a tissue homogenous layer produced by coating. For moisture loss and oil uptake, the coefficient of determination (R2) and root mean square error (RMSE) of eight empirical models were compared. Finally, the Dehghannya and Krokida model (moisture loss) and the Movahhed and Naghavi model (oil uptake) were found the best fit to the experimental data. Although coating pre-treatment and osmotic dehydration can be used as an alternate de-oiling approach for potato chips, the mechanism of oil uptake reduction differ.

Brown adipose tissue (BAT) function may depend on its anatomical location and developmental origin. Interscapular BAT (iBAT) regulates acute macronutrient metabolism, whilst perivascular BAT (PVAT) regulates vascular function. Although phenotypically similar, whether these depots respond differently to acute nutrient excess is unclear. Given their distinct anatomical locations and developmental origins and we hypothesised that iBAT and PVAT would respond differently to brief period of nutrient excess. Sprague-Dawley rats aged 12 weeks (n = 12) were fed either a standard (10% fat, n = 6) or high fat diet (HFD: 45% fat, n = 6) for 72 h and housed at thermoneutrality. Following an assessment of whole body physiology, fat was collected from both depots for analysis of gene expression and the proteome. HFD consumption for 72 h induced rapid weight gain (c. 2.6%) and reduced serum NEFA with no change in either total adipose or depot mass. In iBAT, an upregulation of genes involved in insulin signalling and lipid metabolism was accompanied by enrichment of lipid-related processes and functions, plus glucagon and PPAR signalling pathways. In PVAT, HFD induced a pronounced down-regulation of multiple metabolic pathways which was accompanied with increased abundance of proteins involved in apoptosis (e.g. Hdgf and Ywaq) and toll-like receptor signalling (Ube2n). There was also an enrichment of DNA-related processes and functions (e.g., nucleosome assembly and histone exchange) and RNA degradation and cell adhesion pathways. In conclusion, we show that iBAT and PVAT elicit divergent responses to short-term nutrient excess highlighting early adaptations in these depots before changes in fat mass.

Background/Goals: The gut hormone PYY secreted from intestinal L-cells has been implicated in the mechanisms of satiation via Y2-receptor (Y2R) signaling in the brain and periphery and is a major candidate for mediating the beneficial effects of bariatric surgery on appetite and body weight. Methods: Here we assessed the role of Y2R signaling in the response to low- and high-fat diets and its role in the effects of Roux-en-Y gastric bypass (RYGB) surgery on body weight, body composition, food intake, energy expenditure and glucose handling, in global Y2R-deficient (Y2RKO) and wildtype mice made obese on high-fat diet. Results: Both male and female Y2RKO mice responded normally to low- and high-fat diet in terms of body weight, body composition, fasting levels of glucose and insulin, as well as glucose and insulin tolerance for up to 30 weeks of age. Contrary to expectations, obese Y2RKO mice also responded similarly to RYGB compared to WT mice for up to 20 weeks after surgery, with initial hypophagia, sustained body weight loss, and significant improvements in fasting insulin, glucose tolerance, HOMA-IR, and liver weight compared to sham-operated mice. Furthermore, non-surgical Y2RKO mice weight-matched to RYGB showed the same improvements in glycemic control as Y2RKO mice with RYGB that were similar to WT mice. Conclusions: PYY signaling through Y2R is not required for the normal appetite-suppressing and body weight-lowering effects of RYGB in this global knockout mouse model. Potential compensatory adaptations of PYY signaling through other receptor subtypes or other gut satiety hormones such as GLP-1 remain to be investigated.

The flow properties of pellets or granules are crucial for further processing the drug dosage forms. Optimal compression or filling the multiparticulate dosage forms into capsules is influenced by forces between discrete particles, which could be partially characterized by flow properties. Several techniques were developed for the examination of flowability, including static and dynamic methods applying empirical studies and the up-to-date chaos theory; however newest methods seem only to be powerful with the supplement of empirical principles. Our experiments try to refine both the technique of analysis and the methods by finding new, alternative ways. Our approach to the flowability measurements was to set up a dynamic time-dependent model which combines empirical observations and the chaos theory on a geometrical basis, thus find new aspects regarding flow properties of pellets and granules that could be relevant for drug developers.

The global focus on geopolymer binder production has increased due to the adoption of waste materials and industrial byproducts. Given the gradual decline of the availability of fly ash and ground granular blast furnace slag (GGBFS) resulting from the decarbonization process in electricity and steel productions, waste clay brick powder (WCBP), could be a viable substitute of these pozzolanic by-products. This research is dedicated to thoroughly investigate the techno-eco-efficiency performance of WCBP when utilized as a geopolymer precursor. The favorable mechanical characteristics exhibited by fly ash-GGBFS-WCBP-based geopolymer binder emphasize the importance of assessing its sustainability alongside its technical viability. The study employed life cycle analysis (LCA), following ISO 14040-44 standards, and using the Simapro software, to evaluate the environmental implications of the use of WCBP-based geopolymer mixtures. Human toxicity emerged as the primary impact. Moreover, the analysis of life cycle costs highlighted key financial factors, with around 65-70% attributed to alkaline activators of the total cost. The production of alkaline activators was identified as a critical point for both environmental impact and economic considerations due to energy consumption. While WCBP-rich samples exhibit a 1.7-0.7% higher environmental impact compared to the control mix (CM), their high mechanical strength and cost-effectiveness make them technologically and economically efficient geopolymer mixes. In conclusion, the portfolio analysis for techno-eco-efficiency affirms that mixes containing 40%, 30%, and 20% WCBP are more efficient than those using 10% and 0% WCBP, respectively.

Disposing pollutants into water sources has posed risks to human health and the environment, and biosorption has emerged as an eco-friendly, cost-effective, and green alternative for wastewater treatment. This work shows banana peel powder (BPP) biosorbents for efficient sorption of methylene blue (MB), atrazine, and glyphosate pollutants. The biosorbent highlights several surface chemical functional groups and morphology containing agglomerated microsized particles and microporous structures. BPP showed 66% elimination of MB in 60 min, with an adsorption capacity (qe) of ~33 mg g-1, where a combination of film diffusion and chemisorption governed the sorption process. Besides, the biosorbent removed 91% and 97% of atrazine and glyphosate pesticides after 120 min, with qe of 3.26 and 3.02 mg g-1, respectively. The glyphosate and atrazine uptake best followed the Elovich and pseudo-first-order kinetic, respectively, revealing different sorption mechanisms. Our results suggest that BPP are low-cost biomaterials for green and environmentally friendly wastewater treatment.

The ultrasonic vibration assisted pressing process can improve the fluidity, the uneven distribution of density and particle size of WC-Co powder. However, the microscopic mechanism of ultrasonic vibration on the powder remains unclear. In this paper, WC and Co particles are simulated by three-dimensional spherical models of two particle sizes with the aide of the secondary development of Python. At the same time, the forming process of powder at mesoscale is simulated in the virtue of the finite element analysis software ABAQUS. The influence of vibration amplitude on the fluidity, the filling density and the stress distribution of WC-Co powder is investigated when the ultrasonic vibration is applied to the conventional pressing process. From simulation results, the ultrasonic vibration amplitude has great influences on the density of the compact. With the increase of the ultrasonic amplitude, the compact density also increases gradually. At the initial stage of the compaction, the particles move violently under the action of ultrasonic vibration, the fluidity is obviously enhanced, the arch bridge effect between particles is destroyed, the fine particles quickly fill the pores between the large particles, which increase the density, and the residual stress in the billet decreases after the compaction. From the experimental results, the size distribution of the billet is more uniform, the elastic aftereffect is reduced, the dimensional instability is improved, and the density curves obtained by experiment and simulation are within a reasonable error range.

Introduction: Dental health problems including dental plaque are common health problems affecting people of different age groups globally. Air-polishing is a safe tooth polishing technique used by dental professionals for stain and plaque removal and as preventive procedure for dental health. Here we report the technical improvisation of existing air-polishing technique by supplementing cannabinoid powder into the classic polishing powder for effective removal of supragingival and subgingival plaque and inhibition of plaque forming bacteria. Methods: The cannabidiol (CBD) powder was added to the tooth polishing powder (AIR-N-GO, classic) at 1% (wt/wt) ratio. The study was conducted on 12 patients, of which 6 received regular polishing treatment and 6 received CBD-supplemented polishing treatment. The dental plaque samples were collected before and after each treatment and subjected to in vitro microbiological analysis and the colony forming units (CFU) were analyzed using automated colony counter. Results: Based on in vitro microbiological analysis, the average CFU of interdental space samples collected from post-CBD-supplemented polishing treatment was significantly reduced (linear fold change between 3.9-18.4) compared to that of post-regular polishing (linear fold change between 1.0-2.6) treatment. Conclusions: CBD-supplemented polishing powder can help in effective removal and killing of dental plaque bacteria during the polishing treatment. CBD powder can be added as enhancing supplement to the existing polishing powders.

Inhalation of gasoline vapors (GV) is associated with developing various pathologies. Particularly, oil refinery and gas station workers are at greater risk of developing lung cancer, kidney cancer, bladder cancer, and hematological disorders, including acute myeloid leukemia. Therefore, preventing the harmful effects of GV and alleviating their consequences appear to be an important and timely issue. In this study, we investigated the potential of vitamin D3, turmeric powder and their combination to ameliorate the toxicity of gasoline fumes in rats. Separate groups of animals fed with a standard rodent diet, with or without supplementation of vitamin D3 (750 IU/kg of body weight) and/or turmeric powder (0.5%, w/w, in food), were untreated or treated with GV (11.5±1.3 cm3/h/m3/day) for 30, 60 or 90 days. Changes in the body weight were monitored weekly. Histological, biochemical, and hematological parameters were determined at the end of each treatment period. While exposure of rats to GV resulted in a time-dependent reduction in body weight, supplementation with vitamin D3, but not with turmeric root powder or their combination, partially prevented weight loss. Macroscopical and histological analyses showed pronounced time-dependent changes in the organs and tissues of GV-treated rats. These included alveolar wall collapse in the lungs, destruction of the lobular structure and hepato-cytolysis in the liver, shrinkage and fragmentation of glomeruli in the kidneys, and disorganization of the lymphoid follicles in the spleen. However, co-treatment with the nutritional supplements tested, especially vitamin D3, noticeably alleviated the above conditions. This was accompanied by a significant improvement in blood chemistry and hematological parameters. Collectively, our results demonstrate that the harmful effects of environmental exposure to GV can be reduced upon supplementation of vitamin D3. The fact that the protective activity of vitamin D3 alone was higher than that of turmeric root powder or the combined treatment suggests that combinations of these supplements may not always be more beneficial than each agent applied separately.

Hydrotalcites (HTlc) represents a class of nanostructured layered materials that may be employed in a variety of applications, from green to bio technologies. In this paper, we report an investigation on HTlc made of Mg and Fe, recently employed to improve the growth in vitro of osteoblasts within a keratin sponge. We have carried out an analysis of powder materials and of HTlc dispersed in keratin and spin-coated on a Si/SiO2 substrate at different temperatures. A DC magnetic study of the powders has been carried out with a Quantum Design Physical Property Measurement System, equipped with a Vibrating Sample Magnetometer. The data gathered prove that these HTlc are fully paramagnetic, and keratin shows a very small magnetic response. Optical and Atomic Force Microscopy analyses of the thin films provide a detailed picture of clusters randomly dispersed in the films with various dimensions. The magnetic properties of these films have been characterized using the Nano Magneto Optical Kerr Effect (NanoMOKE) down to 7.5K. The data collected show that the local magnetic properties can be mapped with a micrometric resolution distinguishing HTlc regions from keratin ones. This approach opens new perspectives in the characterization of these composite materials.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

Milk fat globule membrane (MFGM) is a complex tri-layer membrane that wraps droplets of lipids in milk. In recent years, it has attracted widespread attention due to its excellent bioactive functions and nutritional value. The milk fat globule membrane contains a diverse array of bioactive lipids, including cholesterol, phospholipids, and sphingolipids, which play pivotal roles in mediating the bioactivity of the milk fat globule membrane. We sequentially summarize the main lipid types in milk fat globule membrane in this comprehensive review and outline the characterization methods used to employed them. In this comprehensive review, we sequentially describe the types of major lipids found in the milk fat globule membrane and outline the characterization methods employed to study them. Additionally, we compare the structural disparities among glycerophospholipids, sphingolipids, and gangliosides, while introducing the formation of lipid rafts facilitated by cholesterol. The focus of this review revolves around an extensive evaluation of current research on lipid isolates from the milk fat globule membrane, as well as products containing milk fat globule membrane lipids, with respect to their impact on human health. Notably, we emphasize clinical trials encompassing a large number of participants. The summarized bioactive functions of milk fat globule membrane lipids encompass regulation of human growth and development, influence on intestinal health, inhibition of cholesterol absorption, enhancement of exercise capacity, and anti-cancer effects. By offering a comprehensive overview, the aim of this review is to provide valuable insights into the diverse biologically active functions exhibited by lipids in milk fat globule membrane.

Obesity, which is characterized by an excessive accumulation of body fat, is one of the critical factors causing metabolic syndrome. Many studies have been performed to identify appropriate agents to control obesity, but toxicity remains a problem. Herein, we identified that phenylbutyrate (PBA), which has been used to treat urea cycle disorder with very low toxicity for a long time, efficiently inhibited high fat-induced body weight gain in a diet-induced obesity mouse model (DIO model). PBA treatment decreased body fat mass and increased lean composition. Moreover, PBA increased brown adipose tissue (BAT) activity by increasing glucose uptake, thereby improving glucose tolerance and insulin tolerance. Interestingly, PBA could induce the expression of phosphofructokinase (PFKL), a key enzyme in the glycolytic pathway, and knocking down PFKL dramatically repressed the expression level of Ucp1 as well as those of Prdm16, Cidea, Pgc1α, and Pparγ, which are marker genes for BAT activation. These results strongly suggested that PBA could increase energy expenditure by increasing BAT activity via the induction of PFKL. Taken together, PBA could be used as a therapeutic agent for people with obesity to prevent the development of metabolic syndrome.

The energy sensor AMP-activated protein kinase (AMPK) is a key player in the control of energy metabolism. AMPK regulates hepatic lipid metabolism through the phosphorylation of its well-recognized downstream target acetyl CoA carboxylase (ACC). Although AMPK activation is proposed to lower hepatic triglyceride (TG) content via the inhibition of ACC to cause inhibition of de novo lipogenesis and stimulation of fatty acid oxidation (FAO), its contribution to the inhibition of FAO in vivo has been recently questioned. We generated a mouse model of AMPK activation specifically in the liver achieved by expression of a constitutively active AMPK using adenoviral delivery. Indirect calorimetry studies revealed that liver-specific AMPK activation is sufficient to induce a reduction in the respiratory exchange ratio and an increase in FAO rates in vivo. This led to a more rapid metabolic switch from carbohydrate to lipid oxidation during the transition from fed to fasting. Finally, mice with chronic AMPK activation in the liver display high fat oxidation capacity evidenced by increased [C14]-palmitate oxidation and ketone body production leading to reduced hepatic TG content and body adiposity. Our findings suggest a role for hepatic AMPK in the remodeling of lipid metabolism between the liver and adipose tissue.

Treatment techniques for facial paralysis have evolved significantly over the past few decades, offering a variety of options to improve facial symmetry and muscle function. The purpose of this paper is to introduce a novel static treatment technique for the surface of the nasolabial fold (NLF) in patients with chronic facial nerve paralysis, aged between 40 and 80 years, who are not candidates for dynamic rehabilitation and present with NLF erasure. The surgical marking process was initiated by determining the projection of the nasolabial fold on the paralyzed side, through measurement of the NLF on the non-paralyzed side. Subsequently, a line was drawn around the nasal ala, and a second line was demarcated in the medial region of the sulcus. In the region close to the nasal ala, along this second line, a notch was planned. The procedure was conducted under local anesthesia. In this study, four procedures were performed without any complications. Comparatively, the outcomes demonstrated an improvement in facial symmetry, the creation of a new NLF, elevation of the ipsilateral lip commissure, and correction of nasal deviation. The proposed technique is straightforward, reproducible, and can be performed in an outpatient setting.

Background - Technological developments induced lifestyle changes and increase population physical inactivity. This change in lifestyle can affect the male-female morphological and physical fitness differences. The aim of this study is to determine and to compare the effect of sex differences in percentage of body fat on speed and endurance running performance. Methods - 72 male and 64 female students aged 20 to 23 years participated in this study. After assessing their morphological characteristics, running performances during 30 m and 400 m, and maximum aerobic velocity (MAV) and maximal oxygen consumption (VO2max) during a 20 m shuttle running test have been estimated for each subject. Male students were re-tested after being overweighed down with a weight equivalent to the mean differences in body fat recorded between the two sexes in the form of a loaded worn vest. Results – Male presented a percentage of fat mass (17.2 ±2%) significantly (p <0.001) lower than that of women subject (25.0 ±2.5%). Running performances during 30 m and 400 m, MAV and VO2max were significantly (p<0.001) better in males. During the weighted condition, male performances during 30 m and 400 m, MAV and VO2max were attenuated by 6.89%, 14.16%, 6.48% and 10.07%, respectively but remain significantly better than those of female students. Conclusion - The persistence of sex differences after overweighting male students indicates that body fat could be responsible for ≈ 50 to 70% of the observed differences between sexes performances during short and long sprints, and 20 m shuttle running test.

Environmental factors as maternal high-fat diet (HFD) intake can increase the risk of age-related cognitive decline in adult offspring. The epigenetic mechanisms are a possible link between diet effect and neurodegeneration across generations. Here, we found a significant decrease in triglyceride levels in a high-fat diet with resveratrol HFD+RV group and the offspring. Firstly, we obtained better cognitive performance in HFD+RV groups and their offspring. Molecularly, a significant increase in 5-mC levels, as well as increased gene expression of Dnmt1 and Dnmt3a in HFD+RV F1 group, were found. Furthermore, a significantly increased of m6A levels in HFD+RV F1 were found, and there were changes in gene expression of its enzymes (Mettl3 and Fto). Moreover, we found a decrease in gene expression levels of pro-inflammatory markers such as Il1-β, Il-6, Tnf-α, Cxcl-10, Mcp-1 and Tgf-β1 in HFD+RV and HFD+RV F1 groups. Moreover, there was increased gene expression of neurotrophins such as Ngf and Nt3 and its receptors TrkA and TrkB. Likewise, an increase in protein levels of BDNF and p-Akt in HFD+RV F1 was found. These results suggest that maternal RV supplementation under HFD intake prevents cognitive decline in SAMP8 adult offspring, promoting a reduction in triglycerides and leptin plasma levels, changes in the pro-inflammatory profile, restoring the epigenetic landscape as well as synaptic plasticity.

The consumer’s acceptability of hamburgers elaborated with the flank of culling cows in which the content of salt or fat had been partially replaced was studied. A mixture of potassium chloride, potassium ferrocyanide and sodium ferrocyanide was used as substitutes for the salt. Oat flakes or a mixture of chia and flax seeds were used as substitutes for the fat. The hamburgers were tasted by 34 consumers. Consumers did not detect significant differences between the control and the rest of the formulations. Neither the gender nor the age of the consumers influenced the sensory appraisal. However, many comments regarding texture failures were recorded. Therefore, the substitution of salt and / or fat in the composition of hamburgers made with the flank of cows is a viable alternative for the commercialization of these pieces of low commercial value as long as the texture of the same is adjusted to resemble it to the control.

A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites. Pure Mg, Mg-3Sn alloy, and Mg-3Sn+0.2GNP alloy-nanocomposite were synthesized by powder metallurgy followed by hot extrusion. The microstructural characteristics of the bulk extruded samples were explored using X-ray diffraction, field-emission scanning electron microscopy, and optical microscopy and their mechanical properties were compared. The microhardness, tensile strength, and compressive strength of the Mg-3Sn alloy improved when compared to those of monolithic Mg sample and further improvements were displayed by Mg-3Sn+0.2GNP alloy-nanocomposite. No significant change in the compressive strain to failure was observed in both the alloy and the alloy-nanocomposite with respect to that of the pure Mg sample. However, an enhanced tensile strain to failure was displayed by both the alloy and the alloy-nanocomposite.