Fly ash cement has rarely been used in Japan, mainly because its strength development is slower than ordinary Portland cement. In this research, the effect of the new fly ash cement with both high alite (C3S) cement and fly ash modified by electrostatic belt separation method on cracking resistance of precast concrete prepared by steam curing was studied. The mechanical and shrinkage properties of the proposed fly ash concrete were compared with those of concrete made using OPC cement without fly ash. In order to study the cracking tendency of precast concrete with the proposed fly ash cement, thermal stress analysis was conducted taking into consideration of the experimental data of concrete properties with the different concrete mix proportions. A standard precast concrete box culvert model was used in this 3D FEM analysis and the distribution of temperature and relative humidity in cross section and induced restraint stress during and after steam curing were discussed. Steam-cured concrete with fly ash and high alite cement developed higher compressive strength on the first day of age than concrete with OPC. The proposed fly ash concrete developed high cracking resistance in the early days. On the other hand, the results showed that the drying shrinkage at later ages was the main cause of cracking.

The global antibiotic resistance crisis, driven by antibiotic overuse and misuse, is multifaceted. This study aimed to assess the microbiological and genetic characteristics of raw retail pork meat, including the isolation, antibiotic susceptibility testing (AST), whole genome sequencing (WGS) of selected indicator bacteria, antibiotic residue testing, and metagenomic sequencing. Samples were purchased from 10 randomly selected retail stores in Gauteng, South Africa. Samples were aseptically separated, with a portion sent to an external laboratory for isolating indicator bacteria and antibiotic residue testing. Identification of the isolated bacteria was reconfirmed using matrix-assisted laser desorption/ionization-time of flight mass spectrometry (MALDI-TOF MS). AST was performed using the Microscan Walkaway system. WGS and metagenomic sequencing were performed using the Illumina NextSeq 550 instrument. The isolated E. coli and enterococci exhibited little phenotypic resistance, with WGS revealing tetracycline resistance genes. Isolated bacteria and meat samples all harboured tetracycline resistance genes, and the antibiotic residue concentrations were within acceptable limits for human consumption. In the metagenomic context, most identified bacteria were of food/meat spoilage and environmental origin, with the resistome analysis primarily indicating beta-lactam, tetracycline and multidrug resistance genes. Further research is needed to understand the broader implications of these findings on environmental health and antibiotic resistance.

Coronavirus disease-19 (COVID-19) has disproportionately affected certain demographics in England, exacerbating existing health disparities. Effective therapeutics are a critical line of defence against COVID-19, particularly for patients at elevated risk for severe disease. Surveillance systems were established to monitor usage of COVID-19 therapeutics in hospital and community settings and inform stewardship. Three antiviral therapies: nirmatrelvir plus ritonavir (Paxlovid®), remdesivir (Veklury®), and molnupiravir (Lagevrio®); and two neutralising monoclonal antibody therapies (nMAbs): sotrovimab (Xevudy®) and casirivimab with imdevimab (Ronapreve®); were in use in England between July 2020 to April 2023. This paper aims to illuminate trends in the utilisation of COVID-19 therapeutics treatment in both hospital and community settings, stratified by the Index of Multiple Deprivation (IMD) in England. Chapter 3 of the English Surveillance Programme for Antimicrobial Utilisation and Resistance (ESPAUR) report 2022 to 2023 also discusses the epidemiological surveillance of these five directly-acting antiviral COVID-19 therapeutics use in England between 2022 to 2023.

Aerobic vaginitis (AV) is a distinct clinical entity characterized by inflammation and abnormal vaginal microflora. Often mistaken for bacterial vaginosis, AV remains relatively unknown and underdiagnosed. AV's understanding is evolving, with some experts suggesting it may primarily be an immunological disorder, the prevalence of which ranges from 7-13% in non-pregnant women and 4.1-8.3% during pregnancy. Pregnancy can affect susceptibility to vaginal infections, leading to adverse outcomes for the woman and the newborn. This review summarizes the correlation between AV and adverse pregnancy outcomes, particularly preterm birth, the leading cause of morbidity and mortality among neonates. Improved understanding of AV's impact on pregnancy outcomes can lead to early recognition, proper management, and effective interventions. While some studies support an association between AV and preterm labor, the existing knowledge of this relationship remains limited. The evidence suggests that AV may contribute to adverse pregnancy outcomes, mainly preterm birth, but further research is needed to establish a definitive link. Further studies are needed to investigate the underlying mechanisms and clarify AV's role in premature labor. A comprehensive understanding of AV's impact on pregnancy outcomes is crucial for early recognition, appropriate management, and effective interventions.

Porcine parvovirus 8 (PPV8), a novel virus in the Parvoviridae family, was first identified in 2022 in lung samples of domestic pigs from China. Retrospective analyses showed that it had been circulating in China since 1998, but no other countries had reported its presence so far. A recent study conducted in South America did not detect any PPV8-positive samples in that region. Here we report the detection of PPV8 in Hungarian and Slovakian pig farms and the estimated prevalence of the virus in Hungary. Altogether 2230 serum, 233 oral fluid, and 115 processing fluid samples were systematically collected from 23 Hungarian and 2 Slovakian pig farms between 2020 and 2023. A real-time quantitative PCR method was developed to detect the viral genome. Our results revealed the presence of PPV8 on 65% of the Hungarian farms and on both Slovakian farms included in our study, marking its first detection in Europe. Oral fluid samples showed the highest positivity rates, reaching up to 100% in some herds. The viral genome was successfully detected in serum and processing fluid samples too, but with significantly lower prevalence rates of 4% and 5%, respectively. Genetic analysis of 11 partial VP2 sequences demonstrated high similarity to the original Chinese strain but with unique amino acid mutations, suggesting possible local evolution of the virus. Our study presents the first scientific evidence of PPV8 infection outside of China and offers a comprehensive assessment of its prevalence in the Hungarian pig population. Further research is required to understand its potential impact on swine health.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

Objective: This research was aimed to estimate the anti-fatigue effects of arecoline and elucidate its underlying mechanisms using a murine model of central fatigue precipitated by sleep deprivation (SD). Methods: Seventy-two male C57BL/6 mice were randomly allocated into six groups: a control group, a SD-induced fatigue model group, a group receiving Rhodiola Rosea capsules (2.5 mg/kg), and arecoline groups administered low, medium, and high doses (10, 20, and 40 mg/kg, respectively). Following 28 days of continuous administrations, the effects of arecoline on the mouse fatigue-related behaviors was assessed by the behavioral tests, including grip strength, rotarod performance, and weight-bearing swimming endurance. Enzyme-linked immunosorbent assays (ELISAs) were utilized to measure the levels of the relevant biochemical markers. Western blotting was employed to quantify the expression of nuclear factor erythroid 2-related factor (Nrf2), Kelch-like ECH-associated protein 1 (Keap1), heme oxygenase 1 (HO-1), sequestosome-1 (p62), and NADPH quinone oxidoreductase 1 (NQO1) in the gastrocnemius muscle. Results: Arecoline administration notably enhanced grip strength, delayed the onset of fatigue as evidenced by extended latencies in rotarod tests, and increased the duration of weight-bearing swimming in mice. In the elevated plus maze, arecoline significantly reduced both the number of entries and the total distance traveled in the open arms. Arecoline markedly decreased serum levels of creatine kinase, blood urea nitrogen, lactate dehydrogenase, triglycerides, and cholesterol, while elevated total testosterone, lactate dehydrogenase, and immunoglobulin G levels. Furthermore, it significantly increased superoxide dismutase(SOD), catalase(CAT), and glutathione peroxidase activity in the gastrocnemius muscle, reduced malondialdehyde levels, augmented hippocampal SOD and CAT activity, and elevated glycogen stores in both liver and muscle tissues. Neurotransmitter levels were significantly increased, cytokine levels were markedly reduced, and the expression of Nrf2, Keap1, NQO1, p62, and HO-1 in brain tissue was significantly upregulated. Conclusion: The current study for the first time demonstrated that arecoline has significant anti-fatigue activity, and its mechanism of action is related to elevate the levels of glucose and lipid metabolism, relieve oxidative stress damage, inhibit neuroinflammatory response, regulate neurotransmitter levels and Keap1/Nrf2/HO-1 signaling pathway. The current study provides a new insight into the potential of arecoline in prevention and improvement of fatigue.

At present, failure definition and damage characteristic curve (DCC) analysis included in the framework to assess bitumen fatigue cracking performance have an inconsistency in ranking bitumen fatigue behaviour. This study utilized two types of self-healing polymers (STP and IPA1w) to modify the neat asphalt (NA), and research four different types of bitumens: NA, STP-modified bitumen, IPA1w-modified bitumen, and styrene-butadiene-styrene modified bitumen (SBSB), to evaluate the above-mentioned framework. All bitumens were subjected to short-term and long-term aging and tested utilizing the Linear amplitude sweep (LAS) test and simplified viscoelastic-continuum-damage (S-VECD) model. The results showed that the SBSB exhibited the highest numbers of loading cycles (in long-term aging analysis) to reach failure points at 25°C, 28°C, and 31°C which were 2290, 2340, and 2510, respectively. However, this bitumen failed to exhibit the best performance in terms of DCC assessment under the same conditions, confirming the above-mentioned inconsistency. Besides, the current failure criterion could not accurately predict bitumen fatigue behaviour under certain test conditions because two R2 values were below 0.1. As a result, this study proposed a new failure definition and failure criterion to overcome these issues. The proposed failure definition agreed with the DCC analysis to rank bitumen fatigue performance, and the proposed failure criterion showed R2 values higher than 0.9. The new framework presented the modified bitumen containing 0.5% of STP as the asphalt binder with the best fatigue cracking performance, according to the selected test conditions.

This article presents a description of a new method for solving the factorization problem, based on the gradient descent algorithm. This approach demonstrates significant improvements in efficiency compared to traditional methods proposed in previous research. This article describes a new method for solving the factorization problem, based on the gradient descent algorithm, and demonstrates the transition from algebraic methods to approaches based on functional analysis. The proposed approach not only improves the efficiency of solving the problem but also allows the application of computational algorithms of functional analysis, opening new possibilities for research and optimization.

One of the major concerns in structural health management (SHM) is the early detection of a growing crack. Using this, future damage due to crack propagation can be mitigated or eliminated by implementing proper repair and maintenance. Acoustic Emission (AE) is a non-destructive testing (NDT) method with potential applications for locating and monitoring fatigue cracks. The research presented in this paper focuses on SHM using AE. A novel AE signal analysis approach was proposed in order to detect crack initiation and assess small crack lengths. Experimental investigation indicated that initiation of a crack could be identified through the statistical analysis of the resulting features of the AE signals. A probabilistic AE-based model for small fatigue crack sizing was developed and the uncertainties of the model were estimated. In addition, a probabilistic model validation approach was implemented to confirm accurate estimation of the results. The outcome of this research can be used to evaluate the integrity of structures under fatigue loading. The proposed approach can also be applied as an approach to manage health and assess prognosis of structures.

Fruit cracking or splitting, a severe physiological disease that highly affects appearance and quality, compromise the commodity value of fruit and also causes huge economical losses to the producers of several fleshy fruit crops. The growth-promoting phytohormone gibberellic acid (GA) and growth-inhibiting phytohormone abscisic acid (ABA) antagonistically regulate numerous developmental processes throughout the plant life cycle. Homeostasis of endogenous GA and ABA play a significant role in the normal growth of fruits, and its imbalance may lead to the occurrence of cracking or splitting during the process of fruit growth, development, ripening and postharvest storage. The pathways of GA and ABA metabolism and signaling have been studied widely, and the major components were well characterized, which including the genes encoding major biosynthesis and catabolism enzymes and the key signaling components. Nevertheless, our knowledge of the mechanisms of GA and ABA governing fruit cracking is not comprehensive enough. In this review, we not only focus on the scenarios of effects of endogenous GA and ABA contents in the fruit and exogenous plant growth regulators GA and ABA treatments, but also endeavor to provide some genetic cues on the function of GA and ABA responsible for fruit cracking modulation. Information from this review aims to strengthen the understanding of potential molecular bases underlying GA and ABA in fruit cracking control and provide guidance in breeding of fruit cultivars with cracking-resistant ideotypes, and also make great theoretical significance in guiding the establishment of integrated prevention and control measures to fruit cracking or splitting.

This paper illustrates an experimental activity for the closed-loop position control of an actuator made using shape memory alloy (SMA) wire. A solution with the self-sensing effect was implemented to miniaturize the systems, i.e., without external sensors. A proportional control algorithm was initially used, demonstrating the idea's feasibility: the wire can behave simultaneously as an actuator and sensor. An experimental investigation was subsequently conducted for the optimization of the developed actuator. As for the material, a Flexinol wire, Ni-Ti alloy, with a diameter of 0.150 mm and a length of 200 mm, was used. Preliminarily, a characterization of the SMA wire at constant and variable loads was carried out: the characteristics detected are elongation vs. electric current and elongation vs. electrical resistance. The control system is PC-based with a data acquisition card (DAQ). A drive board has been designed and built to read the wire's electrical resistance and power it by pulse width modulation (PWM). A notable result is that the actuator works with good precision and in dynamic conditions, even when it is called to support a load up to 65% different from that for which the electrical resistance-length correlation has previously been experimentally obtained, on which the control is based. This opens up the possibility of using the actuator in a counteracting configuration with a spring, which makes hardware implementation and control management simple.

Acacia dealbata Link, named Mimosa in Portugal, is an invasive hardwood species with potential for construction use, but research is limited. The available stock of small-diameter juvenile wood (sjw) logs can help reduce this gap, but tangential cracking at log ends challenges fastener connections. This study evaluated different treatments to control and reduce end-face cracking in sjw logs during air drying, an economical and environmentally friendly procedure. Extreme two-thirds of sixteen Mimosa logs were subjected to two treatments: one with longitudinal kerfs 15 mm deep along the length (2 and 3 kerfs) and the other with a hollow in the centre up to half the length (16 mm and 30 mm diameters). Over 219 days of air drying and compared with the central part, kerfing treatments significantly reduced outer wood tangential cracking (p < 0.001), with the 3-kerf also reducing crack numbers (p < 0.05) but increasing significantly cracks near the pith (p < 0.01). The 30 mm central hollow significantly reduced central perforation cracking (p < 0.05). Results suggest that a combined treatment approach could help mitigate cracking, enhancing the suitability of wild Mimosa logs for construction use.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

The Interdisciplinary Canadian Collaborative ME Research Network (ICanCME), established in 2019, aims to foster research in Canada and contribute to finding the causes and possible treatments for myalgic encephalomyelitis /chronic fatigue syndrome (ME/CFS), thereby reducing the impact of ME/CFS on the health of Canadians. The main objectives of this paper are to suggest standards for ME/CFS research for the collection of data from participants (Recommended Data Elements) and to consider other factors, such as design, language, cultural issues, equity, and diversity. Consensus of the relevant contents of this research guideline was reached during the ICanCME working group meetings and were based on existing guidelines. Members of the working group contributed to guideline development based on their respective expertise. The proposed research guidelines could improve research quality and advance knowledge in the field of ME/CFS, and ultimately benefit ME/CFS patients.

The application of antimicrobials in aquaculture primarily aims to prevent and treat bacterial infections in fish. Inappropriate use of antimicrobials in fish farming may result in the emergence of zoonotic antibiotic-resistant bacteria and subsequent transmission of resistant strains to humans via food consumption. From recently, AMR emerged as a significant public health concern in the aquaculture ecosystem and fisheries. The aquatic environment serves as a potential reservoir for resistant bacteria, with aquaculture practices providing an ideal breeding ground for AMR due to the excessive use of antimicrobials to prevent and treat diseases. The mutual inter-connection of intensive fish farming systems with terrestrial environments, food processing industry and human population creates pathways for the transmission of resistant bacteria, exacerbating the problem further. One Health concept, which recognizes the interconnectedness of human, animal and environmental health, enables a holistic approach to address the challenges posed by AMR. By understanding the evolution of such approach, the future of aquaculture, being the important source of a global animal protein supply, can be safeguarded. Risk mitigation strategies for AMR should be based on One Health concept to contribute to sustainable aquaculture practices that protect human and animal health, ensure food safety and protection of environment.

Escherichia coli is an indicator microorganism in One Health antibiotic resistance surveillance programmes. The purpose of the study was to describe and compare E. coli isolates obtained from pigs and human contacts from a commercial farm in South Africa using conventional methods and whole genome sequencing (WGS). Porcine E. coli isolates were proportionally more resistant phenotypically and harboured a richer diversity of antibiotic resistance genes, as compared to human E. coli isolates. Different pathovars, namely ExPEC (12.43%, 21/169), ETEC (4.14%; 7/169), EPEC (2.96%, 5/169), EAEC (2.96%, 5/169) and STEC (1.18%, 2/169) were detected at low frequencies. Sequence type complex (STc) 10 were the most prevalent (85.51%, 59/169) among human and porcine isolates. Six STcs (STc10, STc86, STc168, STc206, STc278 and STc469) were shared at the human-livestock interface according to multilocus sequence typing (MLST). Core genome MLST and hierarchical clustering (HC) showed that human and porcine isolates were overall genetically diverse, but some clustering at HC2 to HC200 were observed. In conclusion, even though the isolates shared a spatio-temporal relationship, there were still differences in the virulence potential, antibiotic resistance profiles, and cgMLST and HC according to the source of isolation.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil & gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

K417G Ni-based superalloy is widely used in aeroengine turbine blade for its excellent properties. However, the aeroengine rotor blade zigzag crown appears early failure frequently, which is because of the wear problems occurring in the working process. Laser forming repairing (LFR) is a promising technique to repair these damaged blades. Unfortunately, the laser formed Ni-based superalloys with high content of (Al + Ti) have a high cracking sensitivity. In this paper, the crack characterization of the LFRed K417G, the microstructure, microhardness and tribological properties of the coating before and after laser remelting are presented. The results show that the microstructure of as-deposited K417G consists of γ phase, γ′ precipitated phase, γ + γ′ eutectic and carbide. Cracking mechanisms including solidification cracking, liquation cracking and ductility dip cracking are proposed based on the composition of K417G and processing characteristics to explain the cracking behavior of the K417G superalloy during LFR. After laser remelting, the microstructure of the coating has been refined, and the microhardness and tribological properties has been improved. Laser remelting can decrease the size of the cracks in the LFRed K417G but not the number. Therefore, laser remelting can be applied as an effective method for strengthening coating and as an auxiliary method for controlling cracking.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (>0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Acetic acid bacteria (AAB) are major contributors to the production of fermented vinegar, offering various cultural, culinary, and health benefits. Although the residual unpasteurized AAB after vinegar production are not pathogens, these are necessary the safety evaluations including antibiotic resistance for the use as starters. In this research, we investigated the antibiotics resistance profiles of 26 AAB strains, including various species of Komagataeibacter and Acetobacter, against ten different antibiotics using the E-test method. All strains exhibited resistance to aztreonam and clindamycin. Komagataeibacter species demonstrated a 50% resistance rate to ciprofloxacin, analogous to Acetobacter species, but showed twice the resistance rates to chloramphenicol and erythromycin. Genomic analysis of K. saccharivorans CV1 identified intrinsic resistance mechanisms, such as multidrug efflux pumps, thereby enhancing our understanding of antibiotic resistance in acetic acid-producing bacteria. These findings enhance understanding of antibiotic resistance in AAB for food safety and new antimicrobial strategies, suggesting the need for standardized testing methods and molecular genetic study.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Culex quinquefasciatus is an important target for vector control because of its ability to transmit pathogens that cause disease. Most populations are resistant to pyrethroids and often to organophosphates, the two most common classes of active ingredients used by public health agencies. A knockdown resistance (kdr) mutation, resulting in a change from a leucine to phenylalanine in the voltage gated sodium channel, is one mechanism contributing to the pyrethroid resistant phenotype. Enzymatic resistance has also been shown to play a very important role. Recent studies have shown strong resistance in populations even when kdr is relatively low which indicates factors other than kdr may be larger contributors to resistance. In this study, we examined on a statewide scale (over 70 populations), the strength of the correlation between resistance in the CDC bottle bioassay and the kdr genotypes and allele frequencies. Spearman correlation analysis showed only moderate (-0.51) and weak (-0.29) correlation between the kdr genotype and permethrin and deltamethrin respectively. The frequency of the kdr allele was an even weaker correlate. These results indicate, in contrast to Aedes aegypti, assessing kdr in populations of Culex quinquefasciatus is not a good surrogate for phenotypic resistance testing.

Improvement of hydrophysical properties and corrosion resistance of self-compacting concrete to the effects of alternate freezing-thawing and aggressive soils of southern and central Kazakhstan is of interest to a wide range of researchers from the side of practical application of the obtained results in construction practice. It is proposed to form a spatially reinforced fine crystalline structure of cement matrix with maximum dense packing by using a complex modifier (Hyperplasticiser + Polymer + Microsilica + Fibro fibers) in the composition of self-compacting concretes (SCC). The introduction of the calculated amount of the above additives increases the operational reliability of the current SCC compositions, increasing the water resistance to W16, frost resistance to F=500, increasing the compressive strength by 20%, reducing the mass loss of samples during corrosion leaching to 50%. It has been experimentally established that the proposed addition of complex modifier (Hyperplasticiser + Polymer + Microsilica + Fiber fibers) to the SCC composition allows obtaining self-compacting concrete of high quality with improved performance characteristics (compressive strength, water resistance, frost resistance and corrosion resistance). Studies have shown that the complex modifier-modified SCC compositions have a high degree of resistance in aggressive environments and leaching corrosion. Based on the results of the conducted tests, it is possible to recommend the obtained SCC compositions for production of building products working in the zone of alternating freezing-thawing and aggressive soils.

Two austenitic stainless steel (ASS) plates, 304L and 316L, were cold-rolled (304R and 316R) with a 10 % reduction in thickness then subjected to laser welding. Cold-rolling caused a slight surface hardening and introduced residual tensile stress into the ASS plates. The susceptibility to stress corrosion cracking (SCC) of the welds (304RW and 316RW) was determined using the U-bend test pieces in a salt spray. To highlight the stress concentration at the weld’s fusion boundary (FB), the top weld reinforcement was not ground off before bending. Moreover, micro-shot peening (MSP) was performed to mitigate the SCC of the welds by imposing high residual compressive stress and forming a fine-grained structure. Cold-rolling increased the susceptibility of the 304R specimen to pitting corrosion (PTC) and intergranular (IG) microcracking. Moreover, PTC and SCC were found more often at the FBs of the 304RW. The corrosion pits of the peened 304RW (304RWSP) were finer but greater in amount than the un-peened one. The results also indicated that the 316L ASS welds with MSP was resistant to the incidence of PTC and SCC in a salt spray. The better reliability and longer service life of dry storage canister could be achieved by using 316L ASS for construction and application of MSP on it.

Rice, as a staple crop feeding billions, faces constant threats from various diseases jeopardizing global food security. Precise understanding of disease resistance mechanisms is crucial for developing resilient rice varieties. Traditional genetic mapping methods, such as QTL mapping, provide valuable insights into the genetic basis of diseases. However, the complex nature of rice diseases demands a holistic approach to gain accurate knowledge of it. Omics technologies, including genomics, transcriptomics, proteomics, and metabolomics, enable a comprehensive analysis of biological molecules, uncovering intricate molecular interactions within the rice plant. Integration of various mapping techniques using multi-omics data has revolutionized our understanding of rice disease resistance. By overlaying genetic maps with high-throughput omics datasets, researchers can pinpoint specific genes, proteins, or metabolites associated with disease resistance. This integration enhances the precision of disease-related biomarkers with better understanding of their functional roles in disease resistance. Improvement of rice breeding for disease resistance through this integration represents a significant stride in agricultural science because better understanding of the molecular intricacies and interactions underlying disease resistance architecture leads to more precise and efficient development of resilient and productive rice varieties. In this review, we explore how the integration of mapping and omics data can give a transformative impact on rice breeding for enhancing disease resistance.

Carbapenem antibiotics are the drug of choice for treating multidrug-resistant bacterial infections. Metallo-beta-lactamases (MBLs) are carbapenemase capable of hydrolyzing nearly all therapeutically available beta-lactam antibiotics. Consequently, a need to assess the frequency and phenotypic resistance phenomena of two MBL genes in diarrheal and urinary tract infections (UTIs). Samples were collected through a cross-sectional study, with MBLs genes detected via PCR. Two hundred twenty eight diarrheal bacteria were isolated from 240 samples. The most predominant pathogens were Escherichia coli (32%) and Klebsiella spp. (7%). Phenotypic resistance to amoxicillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 50.4%, 65.6%, 66.8%, 80.5%, 54.4%, 41.6%, 25.7%, 41.2%, 37.2%, and 42.9%, respectively.  Total 142 UTI pathogens were obtained from 150 urine samples, with Klebsiella spp. (39%) and Escherichia coli (24%) are the major pathogens. Phenotypic resistance to amoxycillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 93.7%, 75.0%, 91.5%, 93.7%, 88.0%, 72.5%, 13.6%, 44.4%, 71.1%, and 43%, respectively.  Twenty four diarrheal isolates carried either blaNDM-1 or blaVIM genes; the overall MBL gene prevalence was 10.5%. Thirty six UTI pathogens carried either blaNDM-1 or blaVIM genes (25.4%). Seven isolates carried both blaNDM-1 and blaVIM genes.  MBL genes exhibited a strong association with phenotypic carbapenem and other beta-lactam antibiotic resistance. Resistance to carbapenems requires active surveillance and stewardship.

Associating the most influential parameters with the product distribution is of uttermost importance in complex catalytic processes such as fluid catalytic cracking (FCC). These correlations can lead to the information-driven catalyst screening, kinetic modeling and reactor design. In this work, a dataset of 104 uncorrelated experiments, with 64 variables, has been obtained in an FCC simulator using 6 types of feedstock (vacuum gasoil, polyethylene pyrolysis waxes, scrap tire pyrolysis oil, dissolved polyethylene and blends of the previous), 36 possible sets of conditions (varying contact time, temperature and catalyst/oil ratio) and 3 industrial catalysts. Principal component analysis (PCA) has been applied over the dataset, showing that the main components are associated with feed composition (27.41% variance); operational conditions (19.09%) and catalyst properties (12.72%). The variables of each component have been correlated with the indexes and yields of the products: conversion, octane number, aromatics, olefins (propylene) or coke, among others.

Sepsis is a life-threatening syndrome triggered by infection and accompanied by high mortality, with antimicrobial resistances (AMRs) further escalating clinical challenges. Rapid and reliable detection of causative pathogens and AMRs are key factors for fast and appropriate treatment, in order to improve outcome in septic patients. However, current sepsis diagnostics based on blood culture is limited by low sensitivity and specificity while current molecular approaches fail to enter clinical routine. Therefore, we developed a Suppression PCR-based selective enrichment sequencing approach (SUPSETS), providing a molecular method combining multiplex suppression PCR with Nanopore sequencing to identify most common sepsis-causative pathogens and AMRs using plasma cell-free DNA. Applying only 1 mL of plasma, we target eight pathogens across three kingdoms and ten AMRs in a proof-of-concept study. SUPSETS was successfully tested on first ten clinical samples and revealed comparable results to clinical metagenomics while clearly outperforming blood culture. Several clinically relevant AMRs could be detected additionally. Furthermore, SUPSETS provided first pathogen and AMR-specific sequencing reads within minutes of starting sequencing, thereby potentially decreasing time to results to 11 - 13 hours and suggesting diagnostic potential in sepsis.

In this paper, the deformation behavior of S32750 duplex stainless steel during low cycle fatigue was studied by controlling number of cycles. The microstructure of the specimens under different cycles was characterized by optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). Microhardness of two phases was measured by a digital microhardness instrument. The results showed that the microhardness of ferrite increases significantly after the first 4000 cycles, while the austenite shows a higher strain hardening rate after fatigue fracture, and the microhardness of ferrite and austenite increases by 23 HV and 87 HV, respectively. Two-phase kernel average misorientation (KAM) diagram showed that the continuous accumulation of plastic deformation easily leads to the initiation of cracks inside the austenite and at the phase boundaries. The evolution of dislocation morphology in two phases was obviously different. With the increase of cycle number, the dislocation in ferrite gradually transforms from dislocation bundles and dislocation array to sub-grain structure, while the dislocation in austenite gradually develops from dipole array to ordered Taylor lattice network structure.

Relative to several model bacteria, the ethanologenic bacterium Zymomonas mobilis is shown here to have an elevated resistance to exogenous antimicrobial peptides (AMPs) – both, with regard to peptide bulk concentration in the medium, and the numbers of peptide molecules per cell. By monitoring integration of the AMPs in the bacterial cell membrane and observing the resulting effect on membrane energy-coupling, it is concluded that the membranotropic effects of the tested AMPs in Z. mobilis and in Escherichia coli are comparable. The advantage of Z. mobilis over E. coli apparently results from its uncoupled mode of energy metabolism that, in contrast to E. coli, does not rely on oxidative phosphorylation, and hence, is less vulnerable to disruption of its energy-coupling membrane by AMPs. It is concluded that the high resistance to antimicrobial peptides (AMPs) observed in Z. mobilis not only proves crucial for its survival in its natural environment but also offers a promising platform for AMP production and sheds light on potential strategies for novel resistance development in clinical settings.

Aim: We estimated the correlation between serum bilirubin concentrations and insulin resistance in advanced maternal age without diabetes mellitus. Method: The cross-sectional study involved consecutive 50 women of advanced maternal age without diabetes mellitus, and insulin resistance (IR) was diagnosed according to the homeostatic model assessment insulin resistant (HOMA-IR) formula and the cut-off point was set to more than 2.5. Serum bilirubin and HOMA-IR were compared between the IR (+) and IR (-) groups. Results: We found that serum bilirubin levels in the IR subjects were significantly decreased compared to those without IR (p = 0.0252). Serum bilirubin concentrations were negatively correlated with the weight and the fasting insulin concentrations in all subjects (r=−0.282, p=0.047, r=-0.424, p=0.002). Additionally, serum bilirubin had a negatively correlation with HOMA-IR (r = -0.410, p = 0.003) in all subjects. The multiple linear regression analysis found that serum total bilirubin levels were independently correlated with HOMA-IR (beta = -0.392, p= 0.015) in these subjects. Conclusions: The study demonstrated that serum bilirubin concentrations had negatively correlation with insulin resistance in advanced pregnant women without diabetes mellitus, and decreased serum bilirubin may forebode increased gestational diabetes mellitus risk in our study population.

This study explored the effects of cryogenic treatment on the microstructure, hardness, and wear-resistance of diamond-like carbon (DLC) by cryogenically treating NAK 80 mold steel coated with DLC. Raman spectroscopy analyzed the structure of the DLC film. Nanoindenter analyzed the hardness and Young’s modulus of the film, and their relationship determined the wear resistance. Wear test assessed the wear rate and friction coefficient of the DLC film. The results showed that cryogenic treatment increased the rate of carbide precipitation and refined the grain structure. Raman spectroscopy indicated that the Raman intensity rate (I_D/I_G) of treated DLC films was smaller than those without cryogenic treatment. When the sp3 bond increased, the hardness and wear-resistance of the DLC film also increased.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

In recent years, the emergence of cancer drug resistance is one of the crucial tumor hallmarks which is supported by the level of genetic heterogeneity and complexities at cellular levels. Oxidative stress, immune evasion, metabolic reprogramming, overexpression of ABC transporters and stemness are among the several key contributing molecular and cellular response mechanisms. Topo-active drugs, e.g., doxorubicin and topotecan, are clinically active and are utilized extensively against a wide variety of human tumors and often results in the development of resistance and failure to therapy. Thus, there is an urgent need for an incremental and comprehensive understanding of mechanisms of cancer drug resistance specifically in the context of topo-active drugs. This review delves into the intricate mechanistic aspects of these intracellular and extracellular topo-active drug resistance mechanisms and explores use of potential combinatorial approaches by utilizing various topo-active drugs and inhibitors of pathways involved in drug resistance. We believe that this review will help guide basic scientists, pre-clinicians, clinicians, and policymakers toward holistic and interdisciplinary strategies that transcend resistance, renewing optimism in the ongoing battle against cancer.

In the FCC conversion of heavy petroleum fractions as atmospheric residues, the main challenge for refiners to achieve the quantity and quality of various commercial products depends essentially on the catalyst used in the process. A deep characterization of the catalyst at different steps of the process (fresh, regenerated, and spent catalyst) was investigated to study the catalyst's behavior including the physicochemical evolution, the deactivation factor, and kinetic-thermodynamic parameters. All samples have been characterized by various spectroscopy methods such as N2 adsorption-desorption, UV-visible spectroscopy, Raman spectroscopy, LECO carbon analysis, Scanning electron microscopy (SEM), X-ray diffraction (XRD), X‐ray fluorescence (XRF), nuclear magnetic resonance spectroscopy (NMR13C) analysis, and Thermogravimetric analysis. The results of N2 adsorption-desorption, UV-vis, Raman, LECO carbon, and SEM images showed that the main causes of catalyst deactivation and coking were the deposition of carbon species that covered the active sites and clogged the pores, and the attrition factor due to thermal conditions and poisonous metals. The XRD and XRF results showed the catalyst’s physicochemical evolution during the process and the different interlinks between catalyst and feedstock (Nickel, Vanadium, Sulfur, and Iron) elements which should be responsible for the coking and catalyst attrition factor. It has been found that, in addition to the temperature, the residence time of the catalyst in the process also has an influence on catalyst structure transformation. NMR13C analysis revealed that polyaromatic hydrocarbon is the main component in the deposited coke of the spent catalyst. Thermogravimetric analysis showed that the order of catalyst mass loss was fresh > regenerated > spent catalyst due to the progressive losses of the hydroxyl bonds (OH) and the structure change along the catalyst thermal treatment. Moreover, the kinetic and thermodynamic parameters showed that all zones are non-spontaneous endothermic reactions.

Rising antimicrobial resistance (AMR) in Salmonella serotypes host-adapted to cattle is of increasing concern to the beef and dairy industry. The bulk of the existing literature focuses on AMR post-slaughter. In comparison, the understanding of AMR in Salmonella among pre-harvest cattle is still limited, particularly in Texas, which ranks top five in beef and dairy exports in the United States; inherently, the health of Texas cattle has nationwide implications for the health of the United States beef and dairy industry. In this study, long-read whole genome sequencing and bioinformatic methods were utilized to analyze antimicrobial resistance genes (ARGs) in 98 isolates from beef and dairy cattle in the Texas Panhandle. Fisher exact tests and elastic net models accounting for population structure were used to infer associations between ARGs and antimicrobial phenotypic profiles and metadata. Gene mapping was also performed to assess the role of mobile genetic elements in harboring ARGs. ARG were found to be statistically different between the type of cattle operation and Salmonella serotypes. Beef operations were statistically significantly associated with more resistance genes compared to dairy operations. Salmonella Heidelberg, followed by Salmonella Dublin isolates, were associated with the most ARGs. Additionally, specific classes of ARGs were only present within mobile genetic elements.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

It has been known for nearly over 150 years that fatigue life data exhibits a considerable amount of variability. Furthermore, statistically modeling fatigue life adequately is challenging. Different empirical approaches have been used, each of which has merit; however, none is appropriate universally. Even when a sufficiently robust database exists, the scatter in the fatigue lives may be extremely large and difficult to characterize. The complications in empirical modeling are exacerbated for long life estimation when experimental observations are rare. The purpose of this work is to review traditional and more modern empirically based methodologies for estimating the cumulative distribution functions for fatigue life, given an applied load. To assess the applicability of the methods confidence bounds will be estimated. The analyses will be performed on an historic set of data for annealed aluminum wire tested in reverse torsion fatigue. These data are available in publications. It is recommended that a time dependent distribution function that is an based on principles of reliability that can be generalized for a variety of modeling applications should be considered for fatigue life estimation.

The emergence of antibiotic-resistant Campylobacter jejuni, a leading cause of gastroenteritis worldwide, presents a significant public health challenge requiring vigilant surveillance and disease control. This study aimed to characterize C. jejuni strains isolated in Romania from 2017-2020, focusing on genetic diversity, virulence, and antibiotic resistance determinants. The isolates underwent phenotypical testing, PCR, and antibiotic resistance assessment using Disc Diffusion Kirby–Bauer for ciprofloxacin, nalidixic acid, erythromycin, and tetracycline. Genetic analysis identified resistance and virulence genes, point mutations, and performed sequence typing (7-gene MLST) to determine genetic relatedness. Results indicated substitutions at position 86 in the amino acid sequence or position 257 in the nucleotide sequence of the gyrA gene in 47 fluoroquinolone-resistant isolates. Additionally, mutations in the rRNA23S gene at positions 2074 and 2075, associated with macrolide resistance, were found in 12 of the 66 isolates. Allelic profiles generated 38 sequence types (STs), including three new STs not present in the reference database. The sequence data analysis revealed a genetically diverse C. jejuni population with a weak clonal structure. This study provides crucial insights into the genetic diversity and antibiotic resistance of C. jejuni strains in Romania, highlighting the need for ongoing surveillance and control measures.

Leaf springs are critical components for the railway vehicle safety in which they are installed. Although these components are produced in high-strength alloyed steel and designed to operate under cyclic loading conditions in the high-cyclic fatigue region, their failure is still possible to occur and hence lead to economic and human catastrophes. The aim of this document is precisely to characterise the mechanical crack growth behaviour of the 51CrV4 spring steel representative of leaf springs under cyclic conditions, that is, crack propagation in mode I. The common fatigue crack growth prediction models (Paris and Walker) considering the effect of stress ratio and parameters such as propagation threshold, critical stress intensity factor and crack closure ratio are also determined using statistical methods, which resulted in good approximations with respect to the experimental results. Lastly, the fracture surfaces under the different test conditions were analysed using SEM, with no significant differences to declare. As a result of this research work, it is expected that the developed properties and fatigue crack growth prediction models can assist design and maintenance engineers in understanding fatigue behaviour in the initiation and propagation phase of cracks in leaf springs for railway freight wagons.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

Excessive oxidative stress and exercise-induced fatigue reduce physical performance and can lead to dysfunction in antioxidant systems within muscular and hepatic tissues. Integrating natural substances with exercise may mitigate fatigue via anti-oxidant effects. This study aims to compare and evaluate the effects of exercise and supplementation with Sundarbans honey vs energy drinks on the strength, anxiety physiological profiles, and hepatic antioxidant capacity in mice undergoing extraneous exercise and fatigue. Forty-eight four-week-old Swiss albino mice were randomly assigned to one of eight groups: (1) Control, (2) Speed™ (Sp), (3) Royal Tiger™ (RT), (4) Sundarbans Honey (SH), (5) Exercise (Ex), (6) Exercise + Sundarbans Honey (Ex+SH), (7) Exercise + Speed™ (Ex+Sp), and (8) Exercise + Royal Tiger™ (Ex+RT). Supplements were administered via oral gavage: Sp (2.5 ml/kg BW), RT (2.5 ml/kg BW), and SH (1 g/kg BW), four times a week for 60 days. Mice in the Ex, Ex+SH, Ex+Sp, and Ex+RT groups underwent daily swimming and running. The strength, fatigue, anxiety levels, lipid profiles, and antioxidant biomarkers were evaluated post-treatment. The SH, Ex, and Ex+SH groups exhibited significantly enhanced physical performance (p

We report the development of an extrinsic self-healing coating system that shows no fluorescence from the intact coating, yellowish fluorescence in cracked regions, and greenish fluorescence in healed regions, thus allowing the separate monitoring of cracking and healing of coatings. This fluorescence monitoring self-healing system consisted of a top coating, an epoxy matrix resin containing mixed dye-loaded in single microcapsule. The dye-loaded microcapsules consisted of a poly(urea-formaldehyde) shell encapsulating a healing agent containing MAT-PDMS and styrene, a photo-initiator and a mixture of two dyes, one that fluoresces only in the solid state (DCM) and a second that fluoresces dramatically increased in the solid than solution state (4-TPAE). A mixture of the healing agent, photo-initiator and the two dyes was yellow due to fluorescence from DCM. On UV curing of this mixture, however, the color changed from yellow to green and the fluorescence intensity increased due to fluorescence from 4-TPAE in the solid state. When a self-healing coating embedded with microcapsules containing the DCM/4-TPAE dye mixture was scratched, the damaged region exhibited a yellowish color that changed to green after healing. Thus, the self-healing system reported here allows the separate monitoring of cracking and healing based on changes in fluorescence color.

The concept of Design Fatigue Factors (DFFs) was introduced for providing desired level of safety in structural fatigue design, often associated with damage calculated from S-N curves. Calculation of fatigue damage from S-N curves can be affected by multiple factors, e.g. types of weld class, corrosion condition, loading conditions, stress concentration on different geometries etc. Each of them can be subject to different level of uncertainties. This study intends to recalibrate the DFFs from a detailed reliability analysis by investigating the probabilistic models derived from the database of S-N curves that has been most frequently used in offshore wind industry. The results of such study indicate that the DFFs can be reduced substantially for the corrosive environmental fatigue models from current standards to the same level of target reliability.

This study investigates the stress corrosion cracking (SCC) behavior of type 316L stainless steel (SS316L) produced with sinter-based material extrusion additive manufacturing (AM). This technology has been shown to produce SS316L with microstructures and mechanical properties comparable to its wrought counterpart in the annealed condition. However, despite plenty of research on SCC of SS316L, little is known about SCC in sinter-based AM SS316L. This study focuses on the influence of sintered microstructures on susceptibility to SCC initiation and crack-branching. Custom-made C-rings were exposed to different stress levels in acidic chloride solutions at various temperatures. To better understand the SCC behavior of SS316L, solution-annealed (SA) and cold-drawn (CD) wrought SS316L were tested for comparison. Results showed that sinter-based AM SS316L was more susceptible to SCC initiation than SA wrought SS316L but more resistant than CD wrought SS316L. Moreover, sinter-based AM SS316L showed noticeably better resistance to crack-branching than both wrought SS316L counterparts. The investigation was supported by comprehensive pre- and post-test microanalysis using light optical microscopy (LOM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and micro-computed tomography (micro-CT)

In this work, the recently proposed cracking elements method (CEM) is used for simulating the damaging processes of structures with initial imperfections. CEM is built in the framework of conventional FEM which is formally like a special type of finite element. The disconnected piecewise cracks are used for representing crack paths. Taking the advantages of CEM that both the initiations and propagations of cracks can be naturally captured, we numerically study the uni-axial compression tests of specimens with multiple joints and fissures, where the cracks may propagate from the tips, or from some other unexpected positions. Though uni-axial compression tests are considered, mainly tensile damage criteria are used in the numerical model. On one hand, the results demonstrate the robustness and effectiveness of the CEM while on the other hand, some drawbacks of the present model are demonstrated, showing the future work.

In 2011, it was reviewed that there is a strong co-occurrence between major depression and chronic fatigue syndrome (CFS), with fatigue and physio-somatic symptoms being key symptoms of depression, and depressive symptoms appearing during the course of CFS. Moreover, the comorbidity between both conditions may in part be explained by activated immune-inflammatory pathways, including increased translocation of Gram-negative bacteria and increased levels of pro-inflammatory cytokines, such as interleukin (IL)-1. Nevertheless, the possible involvement of activated microglia in this comorbidity has remained unclear. This paper aims to review microglial disturbances in major depression, CFS and their comorbidity. A comprehensive literature search was conducted using the PubMed / MEDLINE database to identify studies that are relevant to this current review. Depressed patients present neuroinflammatory alterations, probably related to microglial activation, while animal models show that a microglial response to immune challenges including lipopolysaccharides is accompanied by depressive-like behaviors. Recent evidence from preclinical studies indicate that activated microglia have a key role in the onset of fatigue. In chronic inflammatory conditions, such as infections and senescence, microglia orchestrate an inflammatory microenvironment thereby causing fatigue. In conclusion, based on our review we may posit that shared immune-inflammatory pathways and activated microglia underpin comorbid depression and CFS and that activated microglia are the main orchestrators of this comorbidity. As such, microglial activation and neuro-inflammation may be promising targets to treat the overlapping manifestations of both depression and CFS.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

Chili peppers (Capsicum annuum L.) are economically important crop worldwide. Pepper yellow leaf cure Thailand virus (PepYLCTHV), a Begomovirus causing yellow leaf mosaic disease of chili pepper has been reported to damage 95% economic loss under favorable epidemic conditions. Thirty-one chili genotypes were screened for resistance to PepYLCTHV disease through challenge inoculation using 10-15 viruliferous whiteflies per plant. We purified two resistant lines (PEP6 and PEP12) through four generations of selfing and selection through challenged inoculations. At the 28 days after inoculations two chili genotypes showed symptoms less based on disease severity and percentage of disease incidence of 30 plants PEP6 showed a disease severity 3.64 with 69.33 % DI and PEP12 showed a disease severity 3.83 with 77.67 % DI. PEP6 and PEP12 were selected for pure-line development for four cycles.Both varieties showed an increase in percentage of the resistant plant 12.78 % and 16.77 %, respectively. These lines have potential for release as resistant lines for improvement chili pepper resistance to PepYLCTHV and for developing maker associated with the resistant trait.

This review article focuses on the role of Artificial Intelligence (AI) in transforming healthcare in Africa, specifically in combatting infectious diseases, neglected tropical diseases (NTDs), and antimicrobial resistance. We provide a comprehensive overview of the significance of AI in the healthcare industry, highlighting its urgency and importance in addressing these specific health challenges in Africa. We begin by discussing the role of AI in infectious disease surveillance and outbreak detection. We explore how AI technology can be employed for real-time tracking and prediction of outbreaks, providing examples of successful AI applications in infectious disease surveillance within the African context.Next, we examine the potential of AI-enabled diagnosis and treatment for faster and more accurate diagnoses of infectious diseases and NTDs. We highlight specific examples of AI applications in diagnosing and treating these diseases in Africa, showcasing the potential of AI to improve clinical outcomes and save lives.Furthermore, we focus on how AI-driven drug discovery and development can expedite the search for new treatments for infectious diseases and combat antimicrobial resistance. We present examples of AI applications in drug discovery within the African context, illustrating the potential for AI to revolutionize the development of effective therapeutics.In addition, we delve into how AI-powered public health interventions can enhance the design and implementation of targeted interventions. We explore how AI can optimize resource allocation and facilitate data-driven decision-making processes, providing examples of AI applications in public health in Africa.Finally, we address the challenges and limitations of implementing AI in combatting infectious diseases, NTDs, and antimicrobial resistance in Africa. We discuss potential barriers and ethical concerns surrounding AI applications in healthcare, aiming to encourage informed and responsible utilization of AI technologies.Overall, this review emphasizes the importance and potential of AI in combatting infectious diseases, NTDs, and antimicrobial resistance in Africa. It positions AI as a catalyst for revolutionizing healthcare in the region, leading to more effective disease surveillance, diagnosis, treatment, drug discovery, and public health interventions.

The KcsA is a prokaryotic potassium-oriented channel, which is sourced from the Streptomyces lividans soil bacteria. From extensive studies that have been carried over the KcsA potassium channel, it has been proved that various factors enable the gating and shuttling of the potassium ions into and out of the cells. Some of the factors include the different concentration of protons in the inside and outside membrane. The other factor is the existence of the selectivity filter equipped in the exit of channel pore, which enables the movement of the K⁺ ions. Not only are potassium ions present in the channel but also sodium ions. Potassium and sodium ions are the ions that are essential in the conductivity of a cell because of their charge. An intuitive idea about why K⁺ ions are at least 10,000 times more permeant than Na⁺ ions is presented in various entities. The hypothesis is that the selectivity ratio is probably related to the successive entry of Na⁺ ions, based on the premise that the ratio seems to be relevant to unpredictable quantities caused by Brownian corrosion of ions.

Drug resistance in melanoma is a major hindrance in cancer therapy. Growth hormone (GH) plays a pivotal role in contributing to resistance to chemotherapy. Knocking down or blocking the GH receptor has been shown to sensitize the tumor cells to chemotherapy. Extensive studies have demonstrated that exosomes, a subset of extracellular vesicles, play an important role in drug resistance by transferring key factors to sensitize cancer cells to chemotherapy. In this study, we explore how GH modulates exosomal cargoes from melanoma cells and their role in drug resistance. We treated the melanoma cells with GH, doxorubicin, and GHR antagonist, pegvisomant, and analyzed the exosomes released. Additionally, we administered these exosomes to recipient cells. The GH-treated melanoma cells released exosomes with elevated levels of ABC transporters (ABCC1 and ABCB1), N-cadherin and MMP2, enhancing drug resistance and migration in recipient cells. GHR antagonism reduced these exosomal levels, restoring drug sensitivity and attenuating migration. Overall, our findings highlight a novel role of GH in modulating exosomal cargoes that drive chemoresistance and metastasis in melanoma. This understanding provides insights to the mechanisms of GH in melanoma chemoresistance and suggests GHR antagonism as a potential therapy to overcome chemoresistance in melanoma treatment.

Rice blast is the most harmful disease caused by Magnaporthe oryzae, leading to yield loss. The aim of the work is to improve resistance of rice to blast by introducing and pyramiding genes using conventional breeding technique and modern MAS analysis. Pyramiding is the combination of several resistance genes in one genotype, in this case it improves the resistance of rice to pathogens. MAS analysis revealed that 3 out of 4 studied domestic high-yielding rice cultivars (Bakanasski, Aisaule and Aru) contain 1 blast resistance gene (Pi-2). It was discovered 7 pyramidal lines with the introduction of a combination of 2 blast resistance genes (Pi-1 and Pi-ta) into 6 hybrids and 3 genes (Pi-1, Pi-33 and Pi-ta) into 1 line. Phytopathological test of local cultivars and pyramidal lines of rice showed that 3 out of 7 pyramidal lines have moderate resistance: 2 lines (F2 Bakanasski/7667 (var. vulgaris Koern.) and F2 Aisaule/7664 (var. italica Alef.)), containing 2 resistance genes (Pi-1 and Pi-ta) and 1 line – F2 Aisaule/7689 (var. zeravschanica Brsch.), carrying 3 genes (Pi-1, Pi-33 and Pi-ta), while the local cultivars Bakanasski, Aisaule and Aru are susceptible. As a result, the blast resistance of rice was improved by creating pyramidal lines. Pyramided lines can be used for germplasm exchange and in rice breeding programs to improve blast resistance in rice.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

The impact of systemic vascular resistance (SVR) in hypertrophic (HCM) and amyloid cardio-myopathies has been seldom investigated. We studied pressure-strain loop derived myocardial work (MW) indices and SVR in patients with either sarcomere HCM or wild type transthyretin cardiac amyloidosis (ATTR), presented with heart failure and preserved left ventricular ejection fraction (HFpEF) at the outpatient cardiology units at Messina and Catania University Hospitals (Italy). Patients were in sinus rhythm and needed to have good transthoracic ultrasound imaging quality to undergo transthoracic strain-echocardiography. Other than conventional parameters, SVR and GWI (global work index) were measured. Based on cross-tabulation (a way to assess the ventricular-arterial coupling), the patients were then classified in 4 classes according to the cut-off values suggested by previous studies of 1,440 dyne/s/cm-5 for SVR (Stefadouros et al., 1973) and 1576 mm Hg% for GWI (Olsen et al., 2022). Sixty patients, 30 in each group, aged 61±16 years, 78% males, were studied. HCM were younger than ATTR patients and in a better clinical status (23% HCM vs 77% ATTR were NYHA class 3, p<0.001). Overall, 51 patients (85%) showed high SVR, of whom 21 were HCM (70%) and 30 ATTR (100%) (p<0.005). Both, SVR and GWI were impaired (the poorest class C) in 43% HCM patients (with greater left ventricular concentric hypertrophy) vs 93% of ATTR patients (in advanced NYHA class) (p<0.001). In conclusion, assessing SVR and GWI in HFpEF patients with HCM or ATTR can help clinicians to interpret the pathophysiological and clinical features of such complex diseases.

Recent works in mechanical fatigue consider that a threshold of entropy exists, the fracture fatigue entropy. The determination of this quantity is usually done considering empirical models for the mechanical power estimation. In this paper, we experimentally observe the existence of a threshold of entropy and exergy in low cycle fatigue for a flat Al-2024 specimen avoiding the use of a model, solely measuring the heat generated during a fatigue test. Results are then compared considering various hypotheses (1D heat dissipation with convection and radiation considered as heat sources, and, heat transfer from a fin with convection and radiation as boundary conditions) to an empirical mechanical model known in the literature and deviations between them are discussed.

Athletes are exposed to high-intensity loads to promote athletic performance, however without appropriate evaluation for its effects. This study investigates the effects of four types of exhaustion exercises on Heart Rate Variability (HRV) and Poincaré features as markers of central fatigue; Creatine Kinase (CK) and blood lactate concentrations ([LA-]b) as biomarkers of peripheral fatigue. To achieve this purpose, ten healthy volunteers were exposed to exhaustive exercise using isotonic-, isometric-, aerobic-, and anaerobic-fatigue protocols. HRV Poincaré features, standard deviation of instantaneous beat-to-beat R-R interval variability (SD1) and standard deviation of continuous long-term R-R interval variability (SD2) variables were collected. Central fatigue was tested through the sympathetic stress index (SS) and the sympathetic and parasympathetic index (SS/SD1). Blood samples were collected at the beginning and at the end of the exercises to determine CK and [LA-]b. The SD1 decreased in each exercise protocol, while the SS and SS/SD1 increased. [LA-]b and CK increased at the end of each protocol and correlated with SD1 and SS/SD1. HRV, CK, and [LA^-]_b are acute markers to detect, both central and peripheral fatigue; sensitive to the type, duration, and intensity of exercise, being HRV a novel noninvasive marker, simple and useful for sports coaches and athletes.

Prostate cancer is the second leading cause of death in males in America, with advanced prostate cancers exhibiting a 5-year survival rate of only 32%. Castration-resistance is often developed during the course of treatment, though its influences require further understanding. This study explores the human microbiome for its implications in castration-resistance and metastasis in prostate cancer. RNA sequencing data was downloaded for bone and soft tissue biopsies of patients with metastatic castration-resistant prostate cancer. These sequences were mapped to bacterial sequences to yield species-level abundance approximations. Numerous species were found to correlate to the expression of known markers of castration-resistance, including AR, PI3K, and AKT. Castration-resistance-associated signaling pathways were also enriched with these species, including PI3K-AKT signaling and endocrine resistance. For their implications in cancer aggression and metastasis, cancer stem cell markers were further explored for relation to these species. EGFR and SLC3A2 were widely downregulated with greater abundance of most species. Our results suggest that the microbiome is heavily associated with castration-resistance and stemness in prostate cancer. By considering the microbiome’s importance in these factors, we may better understand the highly aggressive and highly invasive nature of prostate cancer, allowing for needed improvement in the treatment of this disease.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

Estrogen receptor-positive (ER+) breast cancer is common among postmenopausal women and is frequently treated with Letrozole. Letrozole inhibits aromatase from synthesizing estrogen from androgens. Decreased estrogen slows the growth of tumors and can be an effective treatment. Letrozole resistance is increasingly being observed, which poses a unique problem for patients. We reanalyzed transcriptomic data comparing individuals who responded to Letrozole therapy (responders) to those who were resistant to treatment (non-responders). We identified SOX11 and S100A9 as two genes that significantly differed between these patients; with “PLK1 signaling events” being the most significant signaling pathway. We also identified PRDX4 and E2F8 as the top transcriptional biomarkers for ER+ treatment resistance. Many of the other significant gene products play a known role in ER+ breast cancer or other types of cancer, which partially validate our results. Several of the gene products we identified do not have a characterized role in ER+ breast cancer. Our analysis identified a set of genes that warrant further research to elucidate the molecular mechanism of Letrozole resistance in this patient population, as well as novel high-performing biomarkers. We anticipate that these findings could contribute to improved therapeutic outcomes in human patients.

TThe aim of the work is to present a newly developed stand and methodology of accelerated tests of fatigue strength of flexible propellers and fins. The paper presents the design and concepts of the measuring elements used in the research. Test methodology and water stressing were devel-oped. The mechanical properties of the following materials were presented: Arnitel EL-550 and QUEO 8230 with the addition of PP / EVA 50/50 (polypropylene / ethylene-vinyl acetate) - in the proportion of 70/30 (QUEO 8230 / additive). The constructed test stand and a new method of fa-tigue testing of biomimetic fins made it possible to determine the number of fin movement cy-cles under a given load, which may facilitate the determination of a warranty for a newly intro-duced product. The current consumption by the fin drive and video monitoring allowed for the selection of the range of the number of movement cycles and the determination of the moment of fatigue cracks until the fin structure loses its capacity. During the analysis, the test results showed that the fins made of Arnitel EL-550 did not show changes in the measured values of the current and the force generated by the fin. For a fin made of QUEO 8230, at 35,000 cycles, there is a decrease in the current and force consumed, which indicates the initiation of fatigue damage to the fin. The performed tests can be the basis for the development of standards for the fatigue strength of flexible propellers.

Evidence suggests that COVID-19 infection can cause lasting health consequences. Multidiscipli-nary rehabilitation services have been recommended to reduce the sequalae. However, the effec-tiveness of physical exercise interventions remains insufficiently documented. The aim of this study was to develop and implement a specific and well tolerated protocol-based, intervention to reduce muscle weakness in older adults impacted by COVID-19. Forty six older adults random-ized into Intervention and Control Groups. Isometric and isokinetic strength assessments were conducted for selected muscle groups using JBA Staniak® torquemeter and Biodex System 3 dy-namometer. Functional abilities were evaluated with the Time Up and Go test and Chair Stand Tests. Men in intervention group demonstrated a significant improvement in static conditions for knee flexors (KF), trunk extensors (TE) and trunk flexors (TF) and in dynamic conditions for knee extensors (KE). Women in intervention group showed significant improvement in static condition for EF, KF, TE and TF and in dynamic for a KE and for a KF. The interaction GROUP x TESTING SESSION was significant for Chair test (s) and Chair test (n). Our results demonstrate the effec-tiveness of a well-tolerated, protocol-based approach that can be used to diminish long lasting functional deficits in post-covid survivors.

In the world's first pig-to-human cardiac xenotransplant, the elevated levels of porcine cytomeg-alovirus (PCMV) are considered key factors contributing to patient mortality. This has renewed attention to PCMV, a virus widely prevalent in pigs. Currently, there are no effective drugs or vaccines targeting PCMV, and its high detection difficulty poses challenges for prevention and control research. In this study, antiviral small hairpin RNA (shRNA) was selected and inserted into the Rosa26 and miR-17-92 loci of pigs via a CRISPR/Cas9-mediated knock-in strategy. Further in vitro viral challenge experiments demonstrated that these genetically edited pig cells could effec-tively limit PCMV replication. Through this process, we constructed a PCMV-infected cell model, validated partial viral interference sites, enhanced gene knock-in efficiency, performed gene editing at two different gene loci, and ultimately demonstrated that RNA interference (RNAi) technology combined with CRISPR/Cas9 has the potential to generate pig cells with enhanced antiviral infec-tion capabilities. This opens up possibilities for the future production of pig populations with anti-viral functionalities.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

In this paper, we present a new stress calculation method for flexible structures, particularly, the tensile armors, and apply it to flexible riser fatigue analysis. The method is based on a 3-dimensional curved bar theory. First, the tensile armor center line was described as a cylindrical helix curve, its bended curve length and bending migration length were derived and studied under different friction scenarios. Second, the tensile and bending stiffness was given with consideration of frictional hysteretic effect, and verified through FEA analysis results. Third, we presented the stress calculation formula for tensile armor under tension and bending load. All stress components are considered, including tensile, bending and shear stresses. Fourth, the method was benchmarked with published experimental results on a flexible prototype tension and bending tests, and comparisons showed general agreements. Fifth, the method is further applied to a 8” flexible riser for fatigue assessment and lifetime extension evaluation, and showed the flexible riser has sufficient remaining fatigue life, and is suitable to continue its service under the current operating conditions. Last, conclusions are drawn. It concluded that the presented tensile armor stress calculation method and modelling techniques are valid for flexible riser fatigue analysis. This method is time efficient, and can be implemented into other multi-scale models for riser dynamic analysis. It is also applicable to other similar helix structure stress analysis, such as wire ropes, submarine hoses, and subsea umbilicals.

Natural cellulose hydrogels have been widely used to enhance mechanical properties. However, existing natural fiber composite hydrogels are not reusable, limiting their potential applications. To address this issue, we designed and prepared a polyvinyl alcohol/glycerol /bamboo microfibril double network tough hydrogel using a simple method. The bamboo microfibril and polyvinyl alcohol form a tight and rigid network through hydrogen bonding, improving mechanical properties. The prepared polyvinyl alcohol/glycerol/bamboo microfibril double network tough hydrogel has the advantages of reusability and fatigue resistance. Furthermore, both the elastic modulus and toughness of the hydrogel increase with increasing bamboo microfibril content. We also demonstrated that the hydrogel can be recast after cyclic compression, maintaining its recyclability, stability, and certain stiffness and toughness. Our study highlights the potential of hydrogels for controllable mechanical properties, fatigue resistance and shows that polyvinyl alcohol/glycerol/bamboo microfibril hydrogel has broad value for plasticity and reuse.

This paper aims to provide an overall review of degradation, damage evolution and fatigue models in the literature of various engineering materials, mostly metals, and composites.

Reliable fatigue design rules affect the proactive identification of safety parameters in aerospace industry. Numerous fatigue crack initiation and propagation models, linear and nonlinear, have been developed for designing purposes or estimation of the remaining life of aging airplanes. Depending on the adopted assumptions, the accuracy varies for different loading histories, loading types, and materials. Semi empirical models are simple but yield significant inaccuracies. Models with better theoretical basis provide better accuracy, but implementation in real conditions is problematic. In the present work, a review of author’s recent fatigue crack initiation and propagation models based on physical mechanisms is presented and improvements are proposed. Verification of the models on test results is provided and discussed.

In Nature, it is common for living plants and non-living plant tissues to consist of materials with anisotropic multilayer and non-homogenous structure. The structure of tissues determines their self-shaping and self-folding capabilities in response to a stimulus in order to activate different functionalities. Predetermined movements are realized according to changes in environmental conditions, which trigger the fibrous anisotropic structure of the plants’ material. In this study, we present the fabrication process of low-cost anisotropic multilayer materials that are capable of realizing complex movements caused by small temperature changes (<40 ^oC). The mismatch in the thermo-mechanical properties between three or more anisotropic thin layers creates responsive materials that alter their shape owing to the developed internal stresses. Isotropic layers can perform only bending movements, whereas anisotropic multilayer materials can perform bending, twisting or complex combined modes. The movements of the material can be controlled by forming anisotropic homogenous metallic strips over an anisotropic polymer. As a result, inexpensive responsive materials can be developed to passively react to a very broad range of thermal requirements. We studied the major parameters that affect the sensitivity of the developed materials, as well as their failure modes and crack formation under thermal fatigue conditions.

Vancomycin is one of the ‘last-line’ classes of antibiotics used in the treatment of life-threatening infections caused by Gram-positive bacteria. Even though vancomycin was discovered in 1950s it was widely used after 1980s for the treatment of infections caused by methicillin-resistant Staphylococci as prevalence of such strains were increased. However, currently it is evident that vancomycin resistant Staphylococcusaureusandvancomycin-resistant Enterococci have been developed as a result of various reasons including use of avaparcin, which is an analog of vancomycin, as feed additive in livestock. In present day context, more attention should be paid on prevention of emergence of resistance for the antibiotics in order to keep antibiotics effective. In order to prevent emergence of resistance, proper guidance for the responsible use of antimicrobials is indispensable. Therefore, almost all stakeholders who use antibiotics should have in depth understanding on the antibiotic they use. As such, it is imperative to be aware of the important aspects of vancomycin. In the present review, efforts have been made to discussthe pharmacokinetics and pharmacodynamics, indications, emergence of resistance, control of resistance, adverse effects and alternative therapy for vancomycin.

The dynamic resistance is an important parameter in flux pumping. It is simple to calculate in slab geometry but more complex in tapes. In this paper another simple geometry is analysed which is a wire loop. To do this it is essential to make clear what is meant by the term 'voltage', which is ambiguous when there are alternating magnetic fields present. The term can be used if it refers to the EMF along a specified path. However this means that results are dependent on how the voltage leads are attached. If the n value of the V-I characteristic is large simple analytic expressions can be obtained. This will be referred to as the 'Bean' model solution. A more exact approach uses Faraday's law to derive a differential equation which is solved and compared with the Bean model. The dynamic resistance of the loop can be used to drive a flux pump of the type proposed by Geng and Coombs [4] and again simple expressions can be obtained for the performance. If the load is of high inductance L2 and the loop has an inductance L1 then the load current increases exponentially with a characteristic number of cycles L2/L1. The final current can be close to the critical value.

The spread of antimicrobial resistance (AMR) is a global challenge. Close and continuous surveillance for quick detection of AMR can be difficult, especially in remote places. This narrative review focuses on the contributions of pharmacovigilance (PV) as an auxiliary tool for identifying and monitoring the ineffectiveness of, resistance to, and inappropriate use of antibiotics (ABs). The terms “drug ineffective,” “therapeutic failure,” “drug resistance,” “pathogen resistance,” and “multidrug resistance” were found in PV databases and dictionnaires, and denote ineffectiveness. These terms cover a range of problems that should be better investigated because they are useful in warning about possible causes of AMR. “Medication errors,” especially those related to dose and indication, are highlighted in the literature, suggesting inappropriate use of ABs. Hence, the included studies show that the terms of interest related to AMR are not only present but frequent in PV surveillance programs. This review illustrates the feasibility of using PV as a complementary tool for antimicrobial stewardship activities, especially in scenarios where other resources are scarce.

The plate heat exchanger (PHE) is a component that provides heat to be transferred from hot water to domestic cold water without mixing them with high efficiency. Over the lifetime of the PHE, cyclic pressures act on the brazing points and the plates, and this may lead to fatigue failure. The fatigue behaviour of the PHE, designed by using copper-brazed 316L stainless steel, was investigated in this study. First, the fatigue tests under the load ratio R = 0.1 were performed on the Vibrophore 100 testing machine to obtain the S-N curve of the analysed brazed joint. Based on the obtained experimental results, an appropriate material model of the analysed brazed joint has been created, which was validated with numerical calculation in the framework of a program code Ansys. A validated material model was then used for the subsequent numerical analysis of PHE. In order to carry out a numerical calculation using the finite element method (FEM), a 3D model of the heat exchanger was created based on the previous scanning of PHE-geometry. Thereafter, the geometry was parameterised, which allowed us to perform parametric simulations (monitoring different responses depending on the input geometry). Numerical simulations were carried out in the framework of the Ansys software, whereby the obtained results were analysed, and the responses were appropriately characterised according to previously determined load cases.

The underlying molecular basis of Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is not well understood. Characterized by chronic, unexplained fatigue, a disabling payback following exertion (“post-exertional malaise”) and variably presenting, multi-system symptoms, ME/CFS is a complex disease which demands concerted biomedical investigation from disparate fields of expertise. ME/CFS research and patient treatment have been challenged by the lack of diagnostic biomarkers and finding these is a prominent direction of current work. Despite these challenges, modern research demonstrates a tangible biomedical basis for the disorder across many body systems. This evidence is largely comprised of disturbances to immunological and inflammatory pathways, autonomic and neurologic systems, abnormalities in muscle and mitochondrial function, shifts in metabolism, and gut physiology or gut microbiome disturbances. It is possible that these threads are together entangled as parts of an underlying molecular pathology reflecting a far-reaching homeostatic shift affecting each of these systems. Due to the variability of non-overlapping symptom presentation or precipitating events such as infection or other bodily stresses, the initiation of body-wide pathological cascades with similar outcomes stemming from different causes may be implicated in the condition. Patient stratification to account for this heterogeneity is therefore one important consideration during exploration of potential diagnostic developments.

Background: The resurgence of syphilis, primarily in MSM populations, has necessitated novel prophylactic strategies, such as the use of doxycycline post-exposure prophylaxis (doxy-PEP). However, the potential for increased doxycycline use to select for tetracycline resistance represents significant challenges in managing this sexually transmitted infection. This study aims to identify chromosomal mutations associated with tetracycline resistance in Spirochaetales to inform treatment strategies and surveillance measures.Methods: Whole genome sequences (WGS) from the Spirochaetales order, including 4,355 genomes, were analyzed for the presence of mutations in 16S rRNA and non-synonymous mutations in the rpsC and rpsJ genes. The study utilized WGS from GenBank® and sequence data from the PubMLST Treponema pallidum isolate collection. Genetic resistance to tetracycline was detected using a combination of BLASTN searches and gene-gene analysis. Results: A transition mutation TGA to TGG at positions 965-967 in the 16S rRNA gene was detected in 5.6% of Treponema spp. and 3.97% of Spirochaeta spp. genomes. The rpsJ gene exhibited a V57G amino acid substitution across a significant subset of Treponema spp. Notably, the V57K mutation was common in Spirochaeta spp. The rpsC gene had the H178Q mutation and was found to be present in the Spirochaetales bacterium.Conclusion: The identification of mutations associated with tetracycline resistance in Spirochaetales provides a foundation for the development of rapid molecular diagnostics and guides the clinical selection of antibiotics for syphilis treatment. This study underscores the complexity of antibiotic resistance mechanisms and the critical importance of surveillance in the era of antibiotic prophylaxis for STI management.

Elevated circulating triglyceride levels have been linked to an increased risk of diabetes, although the precise mechanisms remain unclear. This study aimed to investigate whether low-density lipoprotein (LDL) cholesterol, homeostatic model assessment (HOMA) for insulin resistance, and C-reactive protein served as mediators in this association across a sample of 18,435 US adults. Mediation analysis was conducted using the PROCESS Version 4.3 Macro for SPSS. Simple medi-ation analysis revealed that all three potential mediators played a role in mediating the associa-tion. However, in the parallel mediation analysis, where all three mediators were simultaneously included, HOMA for insulin resistance remained a significant mediator (indirect effect coefficient, 0.47; 95% confidence interval [CI], 0.43—0.52; p < 0.05) after adjusting for all tested confounding factors. Conversely, LDL cholesterol (indirect effect coefficient, -0.13; 95% CI, -0.31—0.05; p > 0.05) and C-reactive protein (indirect effect coefficient, 0.01; 95% CI, -0.003—0.02; p > 0.05) ceased to be significant mediators. HOMA for insulin resistance accounted for 49% of the association between triglycerides and diabetes. In conclusion, HOMA for insulin resistance was the dominant mediator underlying the association between triglycerides and diabetes. Therefore, reducing triglyceride levels may hold promise for improving insulin sensitivity in diabetic patients.

Predictive studies are essential to establish fundamental data for monitoring and controlling Xylella fastidiosa infections in our country. Limited knowledge exists about how Xylella fastidiosa interacts with the plant host's immune system, leaving numerous unanswered questions regarding Xylella fastidiosa biology and its interactions with national plant hosts. Key inquiries include understanding of how the plant immune system interfaces with Xylella fastidiosa in the xylem and identifying the specific or shared mechanisms underlying the susceptibility of different hosts. Factors such as the presence of insect vectors, abundance of host plants, and climate suitability play pivotal roles in Xylella fastidiosa dispersal. We recommend that countries identified with relatively high risk, like Portugal, undertake thorough individual risk analyses. The implementation of preventive measures and, if necessary, the enhancement of surveillance systems for early detection of Xylella fastidiosa in plants and insect vectors are crucial steps. Additionally, raising awareness is of equal importance to mitigate socioeconomic and ecological impacts on their ecosystems.

Abstract: Lung cancer, characterized by its heterogeneity, presents a significant challenge in ther-apeutic management, primarily due to the development of resistance to conventional drugs. This resistance is often compounded by the tumour’s ability to reprogram its metabolic pathways, a survival strategy that enables cancer cells to thrive in adverse conditions. This review article ex-plores the complex link between drug resistance and metabolic reprogramming in lung cancer, offering a detailed analysis of the molecular mechanisms and treatment strategies. It emphasizes the interplay between drug resistance and changes in metabolic pathways, crucial for developing effective lung cancer therapies. The review examines the impact of current treatments on metabolic pathways and the significance of considering metabolic factors to combat drug resistance. It highlights the different challenges and metabolic alterations in non-small cell lung cancer and small cell lung cancer, underlining the need for subtype-specific treatments. Key signalling pathways, including PI3K/AKT/mTOR, MAPK, and AMPK, have been discussed for their roles in promoting drug resistance and metabolic changes, alongside the complex regulatory networks involved. The article evaluates emerging treatments targeting metabolism, such as metabolic inhibitors, dietary management, and combination therapies, assessing their potential and challenges. It concludes with insights into the role of precision medicine and metabolic biomarkers in crafting personalized lung cancer treatments, advocating for metabolic targeting as a promising approach to enhance treatment efficacy and overcome drug resistance. The review underscores ongoing advancements and hurdles in integrating metabolic considerations into lung cancer therapy strategies.

Chronic Fatigue Syndrome (CFS) can be triggered by different factors and create a complex health situation. In the last decades incidence has been increasing. This situation is a clear example of how humans, viruses, and the environment are all connected. In the 90s cases related to CFS, com-plaints about a feeling of chronic fatigue, inability for everyday tasks, dull pain, cephalalgia, de-pression, anxiety, poor concentration. Clinical tests for EBV, HHV, CMV, IgG, IgM, T4 and T8 subsets were tested, along with hormones and hemogram tests. Most of the cases were women. The timeline of the medical history showed also myomas, breast lumps, premenstrual syndrome previously to CFS development. The nature of these conditions promoted the idea of a possible common link among them and CFS. Some cases also suffered from allergies, food intolerances, candidiasis, intestinal impairment, thyroid implications, endometriosis. As an initial working hypothesis, The Liver Link (TLL) was proposed in order to understand those different conditions affecting body, mind and emotional wellbeing. Considering liver implication can make a differ-ence in treatment and recovery. Low grade inflammatory conditions are related to Th2 predom-inance and liver functions. Functional disharmonies are very important because they usually still do not appear in any conventional tests. In 2002, TLL was presented as a framework to explain the concomitance of CFS and other conditions and the relationship with some viruses such as EBV, HHV, CMV, as a lecture in a congress at the University of Westminster (London). When SARS-CoV-2 outbroke, TLL helped to warn about the post-covid syndrome more likely to occur in specific individuals.

In this paper, we investigate the effects of mean stress, multiaxial loading, and residual stresses on the fatigue life of springs. We study the fatigue life of a homogeneously stressed material subjected to cyclic loading with nonzero mean stress. Traditional methods for estimating fatigue life are based on Goodman and HAIGH diagrams. The formal analytical descriptions, namely "stress-life" and "strain-life" approaches, are found to be more suitable for the numerical methods. The fatigue analysis method described above, which describes crack growth per cycle, is extended. The extensions allow consideration of the mean stress of a load cycle. Closed-form expressions for crack length versus number of cycles are derived. The complementary effects on the fatigue life of springs, which ultimately have a significant influence on the fatigue life of springs, are summarized. For the proposed unified fatigue life functions, the ranges for the stress loading factor are extended by introducing the effective stress intensity. The solution leads to the factor range for the effective stress intensity, the effective mean value of the stress intensity factor and the effective stress ratio. The developed method assumes the homogeneous stress state in the whole spring element. For the non-homogeneously loaded structural elements, the weak-link concept is applied to account for fatigue.

Little is known about how recreational triathletes prepare for an Olympic distance event. The aim of this study was to identify the training characteristics of recreational-level triathletes within the competition period and assess how their preparation for a triathlon influences their health and their levels of fatigue. During the 6 weeks prior to an Olympic distance triathlon, and the 2 weeks after, 9 recreational athletes (5 males, 4 females) completed a daily training log. Participants answered the Daily Analysis of Life Demands Questionnaire (DALDA), the Training Distress Scale (TDS), and the Alberta Swim Fatigue and Health Questionnaire weekly. The Recovery-Stress Questionnaire (REST-Q) was completed at the beginning of the study, on the day before the competition, and at the end of week 8. Training loads were calculated using session-based rating of perceived exertion (sRPE). The data from every week of training was compared to week 1 to determine how athletes’ training and health changed throughout the study. No changes in training loads, duration, or training intensity distribution were seen in the weeks leading up to the competition. Training duration was significantly reduced in week 6 (p=0.041, d = 1.58, 95% CI = 6.9, 421.9), while the number of sessions was reduced in week 6 (Z=2.32, p=0.02, ES = 0.88) and week 7 (Z = 2.31, p=0.02, ES = 0.87). Training was characterized by large weekly variations in training loads and a high training intensity. No significant changes were seen in the DALDA, TDS, or REST-Q questionnaire scores throughout the 8 weeks. Despite large spikes in training load and a high overall training intensity, these recreational-level triathletes were able to maintain their health in the 6 weeks of training prior an Olympic distance triathlon.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

Using the culture-work-health model, this study investigates the factors influencing the quality of life of maritime workers. This study conducted a survey of 320 maritime workers who have experience living and working on a ship for more than six months. This self-administered questionnaire included questions on organizational culture and support, self-efficacy, perceived fatigue, as well as the quality of work life. Organizational culture and self-efficacy were identified as factors affecting the quality of work life, while organizational support was found to have an indirect effect after passing through self-efficacy and perceived fatigue. The final model accounts for 63.1% of the variance in maritime workers’ quality of life. As such, this study shows that self-efficacy is important for the quality of life of maritime workers, having both direct and indirect effects. Moreover, organizational support may prove the primary intervention point for relieving perceived fatigue and enhancing self-efficacy, thus improving the quality of work life.

Myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) is a complex, multisystem, and profoundly debilitating condition, probably of multifactorial etiology. No effective approved drugs are currently available for its treatment. Several studies have proposed symptomatic treatment with melatonin and zinc supplementation in chronic illnesses; however, little is known about the synergistic effect of this treatment on fatigue-related symptoms in ME/CFS. The primary endpoint of the study was to assess the effect of oral melatonin plus zinc supplementation on fatigue in ME/CFS. Secondary measures included participants’ sleep disturbances, anxiety/depression, and health-related quality of life. A proof-of-concept, 16-week, randomized, placebo-controlled, double-blind trial was conducted in 50 ME/CFS patients assigned to receive either oral melatonin (1 mg) plus zinc (10 mg) supplementation (n = 24) or matching placebo (n = 26) once daily. Endpoint outcomes were evaluated at baseline and then reassessed at 8 and 16 weeks of treatment and 4 weeks after treatment cessation, using self-reported outcome measures. Treatment was safe and well-tolerated. The most relevant results were the significant reduction in the perception of physical fatigue in the active group at the final follow-up versus placebo (p < 0.05), and the significant improvement in the physical component summary at all follow-up visits in the experimental group. Our findings suggest that oral melatonin plus zinc supplementation for 16 weeks is safe and potentially effective in reducing fatigue and improving the quality of life in ME/CFS. This clinical study was registered on ClinicalTrials.gov (NCT03000777).

Extensive genome structure variation, such as copy number variations (CNVs) and presence/absence variations, is the basis for the remarkable maize genetic diversity; however, the effect of CNVs on maize herbivory defense remains largely underexplored. Here, we report that the naturally occurring duplication of the maize 9-lipoxygenase gene, ZmLOX5, leads to increased resistance of maize to herbivory by fall armyworms (FAW). Previously, we showed that ZmLOX5-derived oxylipins are required for defense against chewing insect herbivores and identified several inbred lines, including Yu796, that contained duplicated CNVs of ZmLOX5, referred to as Yu796-2×LOX5. To test whether introgression of the Yu796-2×LOX5 locus into the herbivore-susceptible B73 background that contains a single ZmLOX5 gene is a feasible approach to increase resistance, we generated a series of near-isogenic lines that contained either 2, 1 or 0 copies of the Yu796-2×LOX5 locus in the B73 background by six back crosses (BC6). Droplet digital PCR (ddPCR) confirmed the successful introgression of the Yu796-2×LOX5 locus in B73. The resulting B73-2×LOX5 inbred line displayed increased resistance against FAW associated with increased expression of ZmLOX5, increased wound-induced production of its primary oxylipin product, the α-ketol, 9-hydroxy-10-oxo-12(Z),15(Z)-octadecadienoic acid (9,10-KODA), and the downstream defense hormones regulated by this molecule, 12-oxo-phytodienoic acid (12-OPDA) and abscisic acid (ABA). Surprisingly, wound-induced JA-Ile production was not increased in B73-2×LOX5, resulting from the increased JA catabolism. Furthermore, B73-2×LOX5 displayed enhanced drought tolerance likely due to increased ABA and 12-OPDA content. Taken together, this study revealed that the duplicated CNV of ZmLOX5 quantitively contributes to maize antiherbivore defense and presents proof-of-concept evidence that the introgression of naturally occurring duplicated CNVs of a defensive gene into the productive, but susceptible, crop varieties is a feasible breeding approach for enhancing plant resistance to herbivory and tolerance to abiotic stress.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

Wilms tumor (WT), the most prevalent type of renal cancer in children, exhibits overall survival rates exceeding 90%. However, chemotherapy resistance, which occurs in approximately 10% of WT cases, is a major challenge for the treatment of WT, particularly for advanced-stage patients. In this study, we aimed to discover potential mutation markers and drug targets associated with chemotherapy resistance in advanced stage WT. We performed exome sequencing to detect somatic mutations and molecular targets in 43 WT samples, comprising 26 advanced stage WTs, of which 7 cases are chemotherapy-resistant. Our analysis revealed four genes (ALPK2, C16orf96, PRKDC, and SVIL) that correlated with chemotherapy resistance and reduced disease-free survival in ad-vanced-stage WT. Additionally, we identified driver mutations in 55 genes within the chemo-therapy-resistant group, including 14 druggable cancer driver genes. Based on the mutation profile of the resistant WT samples, we propose potential therapeutic strategies involving platinum-based agents, PARP inhibitors, and antibiotic/antineoplastic agents. Our findings provide insights into the genetic landscape of WT and offer potential avenues for targeted treatment, particularly for patients with chemotherapy resistance.

Leafhopper Yamatotettix flavovittatus Matsumura is a phloem feeder that causes significant damage to sugarcane and also transmits sugarcane white leaf (SCWL) disease. Understanding the settling preference, feeding behavior, honeydew production and biophysical factors affecting Y. flavovittatus leafhopper infestation in sugarcane cultivation is crucial for effective pest management strategies. This study investigated these aspects across nine sugarcane cultivars. Significant variability was observed among cultivars in terms of settling behavior, with KK3 and LK92-11 showing the highest number of settled leafhopper adults. Similarly, honeydew production varied significantly among cultivars, with KK3 and LK92-11 exhibiting the highest production. Employing the electrical penetration graph (EPG) technique provided insights into distinct probing behaviors across cultivars, highlighting correlations between settling preference, honeydew production, and specific EPG waveforms. Principal component analysis (PCA) categorized cultivars into four groups based on settling preference, honeydew production, feeding behavior, and biophysical factors. Strong correlations were found between settling preference, honeydew production, and various EPG waveforms, while negative correlations were observed with the number of silica cells and rows per unit area, indicating their potential role in deterring leafhopper settlement. We concluded that TPJ04-768 and K84-200 are promising for resistance to leafhoppers and exploited in sugarcane breeding programs for resistance to insects.

Viroids are known the smallest plant pathogens, and although their genome sequences do not encode proteins, they can cause disease in economically important crops. In order to control viroid diseases and mitigate their damage, genetic resources used for breeding of the viroid-resistant crop have been searched, but the practical resistant trait has not been found in almost all viroid-crop combinations, as well as the tolerant trait. Due to the difficulty in exploiting naturally occurring resistance or tolerance, various effective strategies have been devised to control viroid diseases using non-transforming or transforming techniques. Meanwhile, extensive findings related to viroid resistance and tolerance may lead to confer resistance or tolerance to viroid infection by combining with the recently emerged new technologies (e.g., spray-induced gene silencing and genome-editing technologies), which are believed to be more environmentally viable and acceptable to the general public than previously reported approaches. In particular, some genome-modified crops produced by the latter technology are already on the market. In this review, we comprehensively summarize the current status about investigation of naturally occurring genetic traits for viroid resistance and tolerance, accumulating knowledge about host factors involved in viroid pathogenicity, and various basic technologies developed to try to possible viroid disease control strategies. Furthermore, we discuss prospects and challenges for the achievement of more effective, practical, and sustainable disease control of viroid.

Abstract Background Fatigue Syndrome (FS) is described as extreme exhaustion following ordinary activities. Sleep deprivation, the use of antidepressants, autoimmune illnesses, and anemia are also risk factors for FS. Symptoms of FS include headache, dizziness, and dyspnea, among others. Objective: This study focused on assessing the prevalence of fatigue syndrome (FS) and its association with depression and anxiety, among the medical students in Saudi Arabia. Methodology In this cross-sectional investigation conducted in 2023, 740 medical students participated. Data were gathered using an online survey, which encompassed four key sections: Sociodemographic details, the 11-item Chalder Fatigue Questionnaire (CFQ), the 9-item Primary Health Questionnaire (PHQ) assessing depression, and the Generalized Anxiety Disorder 7-item (GAD-7) scale. Analyses were performed by the use of SPSS version 25. Results A total of 740 students were surveyed, 417 (56.4%) satisfied the diagnostic requirements for fatigue syndrome (FS), with most of them being females. Furthermore, 234 (31.2%) and 296 (40.8%) of the participants reported having significant anxiety symptoms and depressive symptoms, respectively. FS was positively correlated with symptoms of anxiety and depression (P

Triple negative breast cancer (TNBC) is associated with a generally poor prognosis due to its highly aggressive and metastatic nature, lack of targetable receptors, as well as the frequent development of resistance to chemotherapy. We previously reported that AU1, a small molecule developed as an inhibitor of BPTF (bromodomain PHD finger containing transcription factor), was capable of sensitizing preclinical models of triple negative breast cancer to chemotherapy, in part via the promotion of autophagy. In studies reported here, we identify an additional property of this compound, specifically that sensitization is associated with inhibition of the P-glycoprotein efflux pump. In silico molecular docking studies indicate that AU1 binds to active regions of the efflux pump, in a manner consistent with inhibition of pump function. This work identifies a novel chemical structure that can influence multidrug efflux, an established mechanism of drug resistance in triple negative breast cancer, that has not yet been successfully addressed by clinical efforts.

The aim of our study was to assess university students’ sleep quality and fatigue before and during the academic exam period and identify potential associated factors. A Web-based survey was completed by 940 students of 20 different Tertiary Institutions including demographics, sleep habits, exercise, caffeine, tobacco, alcohol use, subjective sleep quality (Pittsburgh Sleep Quality Index - PSQI) and fatigue (Fatigue severity scale – FSS) at the beginning of semester and at examination period. During exam period, PSQI (8.9 vs 6.1, p&lt;0.001) and FSS scores (36.9 vs 32.7, p&lt;0.001) were significantly elevated compared to pre-exam period. Increase of PSQI score was associated with age (β=0.111, p=0.011), presence of chronic disease (β=0.914, p=0.006), and depressive symptoms (β=0.459, p=0.001). Increase of FSS score was associated with female gender (β=1.658, p&lt;0.001), age, (β=0.198, p=0.010), increase in smoking (β=1.7, p=0.029), coffee/energy drinks consumption (β=1.988, p&lt;0.001), decreased levels of physical exercise (β=1.660, p&lt;0.001), and depressive symptoms (β=2.526, p&lt;0.001). In conclusion, our results show that sleep quality and fatigue are affected in university students during exam periods. Potential factors were identified which may lead to development of strategies for better quality of sleep, and wellbeing.

Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is a complex disease characterized by profound fatigue, post-exertional malaise (PEM), and neurocognitive dysfunction. Immune dysregulation and gastrointestinal symptoms are commonly observed in ME/CFS patients. Despite affecting approximately 0.89% of the general population, the underlying pathophysiological mechanisms remain poorly understood. This study aimed to elucidate the relationship between immunological characteristics and intestinal barrier function in ME/CFS patients. ME/CFS patients were stratified into two groups based on their immune competence. After documentation of detailed medical records, serum and plasma samples were collected for assessment of inflammatory immune mediators and biomarkers for intestinal barrier integrity by ELISA. We found reduced complement protein C4a levels in immunodeficient ME/CFS patients suggesting a sub-group specific innate immune dysregulation. ME/CFS patients without immunodeficiencies exhibit a mucosal barrier leakage, as indicated by elevated levels of Lipopolysaccharide-binding protein (LBP). Stratifying ME/CFS patients based on immune competence enabled the distinction of two subgroups with different pathophysiological patterns. The study highlights the importance of emphasizing precise patient stratification in ME/CFS, particularly in the context of defining suitable treatment strategies. Given the substantial health and socioeconomic burden associated with ME/CFS, urgent attention and research efforts are needed to define causative treatment approaches.